Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

In this study, we have included the water footprint (WF) in the process of optimising animal feed rations. The global footprint of cattle production accounts for the largest share (33%) of the global water footprint of livestock production. Using two homogeneous groups of Limousine Podolian young bulls, two different diets were compared: corn silage feeding (CSF), with corn silage-based diet; and the triticale silage feeding (TSF), with triticale silage-based diet. Silage constituted about 41% and 46% of the feed composition (for CSF and TSF, respectively). Diets were characterised by the same energy and protein content. Despite the lower WF in the TSF group than in the CSF group (7726 vs 8571 l/day/calf respectively), no significant differences were found in animal performances (i.e., daily weight gain and final weight), feed conversion and income over feed costs. These results show that simple production decisions can have a significant impact on water resource. Therefore, the use of triticale silage should be further promoted, especially in world regions with limited water resources where low WF feed formulation is more strategic than elsewhere.

The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

Accurate forecast of tail water level (TWL) is of great importance for the safe and economic operation and management of hydropower stations. The predictive performance is significantly influenced by the backwater effect of downstream hydropower stations and tributaries, but the explicit quantification method of the backwater effect is lacked. In this study, a deep learning model based forecasting framework for TWL predictions is established and applied to forecast TWL of Xiangjiaba (XJB) hydropower stations, which is influenced by the backwater effect of downstream tributaries including Hengjiang River (HJR) and Minjiang River (MJR). Firstly, the lag time of the backwater effect of HJR and MJR is analyzed based on the permutation importance. The results demonstrate that the lag time of backwater effect on the TWL of XJB is 5-7 hours for the HJR and 1-2 hours for the MJR. Then, the runoff thresholds of the HJR and MJR for impacting the TWL of the XJB station are obtained by scenario comparison, and the results show that the thresholds of HJR and MJR are 700 m3/s and 7000 m3/s respectively. Finally, the deep learning methods based TWL forecasting model is established based on the lag time and threshold analysis. The model is used to forecast the TWL in future 48 hours. The results show that the forecasting model has a good predictive performance with 98.22% of absolute errors less than 20 cm. The mean absolute error over the validation dataset is 5.27 cm and the maximum absolute error is 63.35 cm.

During the development of horizontal wells in bottom water reservoirs, the strong heterogeneity of reservoir permeability leads to premature bottom water breakthrough at locations with high permeability in the horizontal wellbore, and the water content rises rapidly, which seriously affects production. In order to cope with this problem, a new technology has emerged in recent years that utilizes gravel filling to block the flow in the annulus between the horizontal well and the borehole, and utilizes the Inflow Control Device (ICD) completion tool to carry out segmental water control in horizontal wells. Unlike conventional horizontal well ICD completions that use packers for segmentation, gravel pack combined with ICD completions breaks the original seg-mentation routine and increases the complexity of production dynamic simulation. In this paper, the flow in different spatial dimensions such as reservoir, gravel packed layer, ICD completion section and horizontal wellbore is modeled separately, and the annular pressure at different locations is used as the solution variable for the coupled solution, which realizes the prediction of oil production, water production and water content of gravel pack combined with ICD completions of horizontal wells. The model was used to calculate the effects of different crude oil viscosities, different reservoir permeabilities, different permeabilities of gravel packed layers, and different development stages on the water control effects of gravel pack combined ICD completions and conventional ICD completions at field conditions. This study provides a basis for using gravel pack combined ICD completions in horizontal wells in bottom water reservoirs.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).

water resources in Morocco have been severely influenced by climate change (CC) and pro-longed drought, particularly, in the pre-Saharan zone. The Tafilalet region faces increasing pres-sure due to high demographic growth, increased demand for water, excessive groundwater con-sumption, and investment in agriculture. Using the Water Evaluation and Planning System (WEAP), this study assessed land cover and elevation and created future scenarios using the Standard Precipitation Index (SPI) and Standard Groundwater Level Index (SGI) to monitor hy-droclimate drought conditions in the Ziz watershed from 1989 to 2022. Results show decreasing precipitation, particularly from 2010-2020, with the last four years being the most challenging (SPI<-2). SPI and SGI have a high correlation, suggesting precipitation impacts groundwater in-dicators. Future scenarios predict a high risk of CC, with a 30% decrease in annual precipitation accumulation by 2100 under the optimistic scenario SSP126. Minimum temperature is expected to increase by 1.08°C (SSP126) and 2.61°C (SSP585), and maximum temperature by 1.05°C (SSP126) and 2.93°C (SSP585). Keywords: Climate Change, Water Resources, SPI, SGI, WEAP, Ziz watershed, Drought

Arsenic (As) contamination of groundwater is a common problem in BDP. The alkaline pH of the groundwater provides favourable condition for geomicrobiochemical processes, where organic matter also plays an important role in mobilization of As. The total arsenic content (AsT) of the groundwater is in the range of 69-178 µgL-1 with mean value of 118.58 µgL-1. The groundwater quality of monitored drinking water wells are related to local land–use pattern and rural sanitation installation and practices (which can have a strong influence on microbial contamination). The study indicates that As heterogeneity, probably a consequence of microbial heterogeneity is a feature of the study area. The excessive total and fecal coliform (TC and FC) count of the ponds possibly suggest uncontrolled surface run offs and sewage leakage, notably from nearby pit-latrine, which increased the microbial contamination in these water sources. The tube wells located in close proximity (~ 2-3 m) of the surveyed ponds are also contaminated with high TC and FC values, due to faulty water supply system, pond water infiltration and cracked tube well platforms. Coliforms may influence geomicrobiological processes in groundwater and thereby, contribute in As release and mobilization. The TC and FC values of monitored tube wells and ponds show seasonal variation, with high TC and FC values during wet season. Attempt has been made to focus on sanitation risk of the monitored wells (based on sanitation and fecal coliform scores) which is usually less explored. The sanitary risk score reveal the need of immediate attention to all the sites, as 25.0 %, 58.3 %, 11.1 % and 5 % of tube wells of the six sites fell under very high risk (sanitary risk score ≥ 9), high risk (sanitary risk score 6-8), intermediate risk (sanitary risk score 3-5) and low risk category (sanitary risk score 0-2), respectively. Fecal coliform score classified all the sites under intermediate risk category (FC count 10-100 per 100 ml of water). The predominance of As heterogeneity particularly in areas under high risk category (showing high TC and FC contamination) is observed along with the similar sinusoidal pattern of TC, FC and AsT content. Finally, this study shed light on the factors responsible for unsafe nature of monitored tube wells and the influence of anthropogenic activities on the microenvironment of the groundwater, which could be a probable reason behind the As heterogeneity in the groundwater of the study area.

The way humans use natural resources and especially freshwater, reflects their relationship with nature. It also influences the conceptual Water Resources Management (WRM) model. A historical review shows that the interplay between Humans and Nature is diachronically in constant change between two opposites: conflict and cooperation. Lessons from the past 20.000 years indicate that the WRM model is a function of two main parameters: (1) socio-economics, and (2) climate conditions. Three different Eras of the Humans-Nature relationship have been distinguished: (1) Naturalistic: Nature dominating Humans during the Last Glacial Period (100-10) kyr BC, (2) Dualistic: Nature-Humans cooperation and competition from 10 kyr BC to 1800 AD, and (3) Anthropocentric: Humans dominating Nature from 1800 AD to now. Since 2000, the Integrated WRM (IWRM) model is promoted as state-of-the-art and remains anthropocentric producing huge externalities. Its assessment during the last 20 years has given mixed results and needs to be reformulated. The new model we suggest is based on the dialectical tool for conflict resolution. It unifies Humans and Nature and enhances the social dimension of WRM. After identifying conflicts between stakeholders and the natural laws (eristic part), opposite objectives are unified to harmonize Humans with Nature (dialectical resolution). A case study of flood mitigation illustrates the eristic-dialectical methodology.

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

This paper deals with the use of low earth orbit (LEO) satellite links in long-term monitoring of water, ice and snow levels across wide geographic areas, where no other communication links can be applied. Unlike geostationary satellites, LEO satellites do not maintain the same position relative to the ground station, and transmissions need to be scheduled for satellite overfly periods. For our application, the energy consumption optimization is critical, and we develop a learning approach for scheduling the transmission times from the sensors. Our approach is based on online learning, and is applicable to any LEO satellite transmissions.

In this work Cu2O nanoparticles (NPs) were created in-situ on graphene functionalized with Thermomyces lanuginosus lipase (G@TLL) where site-oriented supported TLL acted as template and binder in the presence of copper salt by tailorable synthesis under mild conditions, producing a heterogeneous catalyst. Cu2O NPs was confirmed by XRD and XPS. The TEM microscopy showed that the nanoparticles were homogeneously distributed over the G@TLL surface with sizes of 53 nm and 165nm. This G@TLL-Cu2O hybrid was successfully used in the degradation of toxic organic compounds such as trichloroethylene (TCE) and Rhodamine B (RhB). In the case of TCE, the hybrid presented a high catalytic capacity, degrading 60 ppm of product in 60 min in aqueous solution and room temperature without the formation of other toxic subproducts. In addition, a TOF value of 7.5 times higher than the unsupported counterpart (TLL-Cu2O) was obtained, demonstrating the improved catalytic efficiency of the system in the solid-phase. The hybrid also presented an excellent catalytic performance for the degradation of Rhodamine B (RhB) obtaining a complete degradation (48ppm) in 50 min in in aqueous solution and room temperature and with the presence of a green oxidant as H2O2.

The management of urban water has evolved from single-function systems to more sustainable designs promoting society and nature as inputs to engineer novel infrastructure. In transdisciplinary research, co-design refers to a design thinking strategy in which people jointly frame a problem-solution. This article presents a conceptual framework to assess a case study focusing on the process of co-design and implementation of green infrastructure as a prototype for stormwater management. The evaluation is carried out from a self-reflective post-implementation perspective. Research activities are translated into the framework to evaluate conditions shaping the trajectory of the prototype. As a result, key aspects driving the research regarding levels of stakeholder participation and dimensions of power are identified. Planning resilient co-design strategies to retrofit urban spaces is necessary to avoid unintended consequences, especially at the initial experimental stages. This study aims to contribute to the continuous improvement of pilot strategies in urban spaces by providing a framework for a structured evaluation of research experiences.

Aquaporins (AQPs) are water channels widely distributed in living organisms and involved in many pathophysiologies as well as in cell volume regulations (CVR). In the present study, based on the structural homology existing between mineralocorticoids receptors (MR), glucocorticoids receptors (GR), cholesterol consensus motif (CCM) and the extra-cellular vestibules of AQPs, we investigated the binding of corticosteroids on AQP family through in silico molecular dynamics simulations of AQP2 interactions with cortisol. We propose for the first time a putative AQPs corticosteroids binding site (ACBS) and discussed its conservation through structural alignment. Corticosteroids can mediate non-genomic effects, nonetheless, the transduction pathways involved are still misunderstood. Moreover, a growing body of evidence is pointing out toward the existence of a novel membrane receptor mediating part of these rapid corticosteroids effects. Our results suggest that the naturally produced glucocorticoid cortisol inhibits channel water permeability. Based on these results, we propose a detailed description of a putative underlying molecular mechanism. In this process, we also bring new insights on the regulatory function of AQPs extra-cellular loops and on the role of ions in tuning the water permeability. Altogether, this work brings new insights into corticosteroids non-genomic effects through the proposition of AQPs as membrane receptor of this family of regulatory molecules. This original result is the starting point for future investigations to define more in depth and in vivo the validity of this functional model.

The paper presents a review of currently available evaluations of the effects of continuously increasing anthropogenic loads on water resources. The increase in the fluxes of elements and compounds into the environment, such as the emission of greenhouse gases and dispersion of nutrients (nitrogen and phosphorus), acidifying gases, and toxic elements and compounds that adversely affect the water quality are considered. The significance of fresh waters as a life support factor of the human populations is demonstrated. Examples are presented to illustrate how key anthropogenic induced processes develop in land waters under the effect of anthropogenic loads, as exemplified by the Russian Kola regions. Climate warming and the increasing dispersion of elements are demonstrated to result in the eutrophication of surface waters even in areas remote from anthropogenic impacted regions. Although the emissions of acidifying gases diminish, the waters are still acidified in acid-vulnerable areas, and the chemical compositions of the waters have been significantly modified over the past decades, which indicates that the changes in the chemical composition of the waters are of irreversible. A new feature of the waters is distinguished: the toxicity of the habitats for aquatic organisms. Arguments are presented for establishing a theoretical approach for evaluating critical loads.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

This paper discusses the use of a participatory approach to assess the level of understanding of the Water-Energy-Climate Change nexus in South Africa. The aim is to facilitate the development of well-coordinated, systematic, and holistic strategies for efficient management of the nexus and its implications in the country. The assessment was guided by the broader Integrated Water Resource Management framework, which promotes a participatory approach in the administration of water resources. The paper argues that despite the reasonable level of understanding of WECC, there is still a lack of integrated policy development and planning among key stakeholders. This is exacerbated by limited coordination and consultation among these stakeholders, particularly policymakers. This necessitates the urgent adoption of holistic and systems thinking approaches, and the promotion of collaboration among different stakeholders mandated to manage WECC sectors. Until such approaches are adopted, the WECC nexus will continue to impede the country’s socio-economic development and environmental wellbeing.

A brief review of the history of the problem is intended to trace the progress in the development of scientific views on the structure of water. The discoveries in this area made in the first half of the last century are considered in comparison with modern data. It is shown that due to the de facto ban on the study of the structure of water in 1971, work in this direction was frozen for a long time. The paradox is that many forgotten truths have been independently "rediscovered" in our time, which speaks of their authenticity. On the basis of scientific literature and their own research, the authors come to the conclusion that water under room conditions is a microdispersed system, one phase of which is represented by continuous water, and the other - by polywater, discovered in the 70s of the last century.

Clearly policy makers should consider the impacts of any decisions they might make before making them. Science can provide estimates of various economic, ecologic, environmental, and even social impacts of alternative policies, impacts that determine how effective any particular policy will be. These impact estimates can be used to compare and evaluate alternative policies in the search for identifying the best one to implement. Among all scientists providing inputs to policy making processes are analysts who develop and apply models that provide these estimated impacts and, possibly, their probabilities of occurrence. But just producing them is not a guarantee that they will be considered by policy makers. This paper discusses ways scientists, including systems analysts, can effectively contribute to and inform those involved in making water management decisions. Brief descriptions of a variety of past and on-going water management policy making processes illustrate both some successes and failures of science informing policy.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

This literature review found that it is doubtful that there is water ice in the polar craters on the Moon. In the course of this review, the following findings were found: (1) The absorption strength of hydroxyl radicals and hydroxyl groups are all 2.9μm, so it is easy to confuse hydroxyl radicals and hydroxyl groups when interpreting M³ spectra data. I do not doubt the ability of LCROSS to detect OH from water, but only suspect that LCROSS is unable to distinguish between hydroxyl radicals from water ice and hydroxyl groups from Moon's methanol due to ignore their spectral identity; (2) The water brought by comets and asteroids and the one caused by solar wind has been exhausted by reacts with the widespread methanol on the Moon in the presence of Pt/α-MoC or Pt/C catalysts. These reacts form large amount of hydrogen, thus clarifying a question NASA raised that "Scientists have long speculated about the source of vast quantities of hydrogen that have been observed at the lunar poles"; (3) The vast quantities of hydrogen in lunar polar craters at extremely low temperatures might be in liquid or solid state now, easy to confuse with water ice. It seems that all our previous misconceptions about water ice in the lunar polar craters might be due to the neglect of the widespread chemical role of lunar methanol. It is necessary to conduct in-depth research in this field in the future.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

Responding to the substantial finance gap for achieving Sustainable Development Goal 6.1 and 6.2, the Water and Sanitation sector has mobilized to launch new blended finance vehicles with increasing frequency. The sustainability and scale-up of financial solutions is intended to support increased access to unserved, marginalized populations. However, without addressing foundational issues in the sector, any finance mechanism, whether public, private or blended, will be a short-term, band-aid solution and the sector will continue the cycle of dependency on external assistance. This paper presents the results of a collaborative effort of Water.org, IRC WASH and the World Bank Water Global Practice. Drawing from the latest research on effective public financial management and based on evidence from the countries where these organizations work, the paper demonstrates that sustainable success in mobilising finance at large scale is dependent on a reasonable level of performance across 10 foundational areas. The paper presents evidence on the 10 foundational areas and discusses why other aspects of finance and governance while necessary are not sufficient. Better coordination amongst all development partners and governments, including a collective commitment to and prioritization of working on these foundational issues, is a necessary first step.

The future of the Colorado River water supply (WS) affects millions of people and the U.S. economy. A recent study suggested a cross-basin correlation between the Colorado River and its neighboring Great Salt Lake (GSL). Following that study, the feasibility of using the previously developed multi-year prediction of the GSL water level to forecast the Colorado River WS was tested. Time-series models were developed to predict the changes in WS out to 10 years. Regressive methods and the GSL water level data were used for the depiction of decadal variability of the Colorado River WS. Various time-series models suggest a decline in the 10-year-averaged WS since 2013 before starting to increase around 2020. Comparison between this WS prediction and the WS projection published in a 2012 government report (derived from climate models) reveals a widened imbalance between supply and demand by 2020. Further research to update similar multi-year prediction of the Colorado River WS is needed. Such information could aid in management decision making in the face of future water shortages.

The order Nymphaeales, consisting of three families with a record of eight genera, has gained significant interest from botanists probably due to its position as a basal-angiosperm. The phylogenetic relationships within the order have well been studied and resolved; however, a few controversial nodes still remain in the Nymphaeaceae including the position of the genus Nuphar. The position of the genus Nuphar and the monophyly of the Nymphaeaceae family remain uncertain. This study adds to the increasing number of completely sequenced plastid genomes of the Nymphaeales and applies large chloroplast gene data set in reconstructing the intergeneric relationships within the Nymphaeaceae. Five complete chloroplast genomes were newly generated, including a first one for the monotypic genus Euryale. Using a set of 66 protein coding genes from the chloroplast genomes of 17 taxa, the phylogenetic position of Nuphar was determined and a monophyletic Nymphaeaceae family was obtained with a convincing statistical support from both partitioned and unpartitioned data schemes. Although genomic comparative analyses revealed a high degree of synteny among the chloroplast genomes of the ancient angiosperms, key minor variations were evident particularly in the contraction/expansion of the Inverted Repeat regions and in RNA editing events. Genome structure, gene content and arrangement were highly conserved among the chloroplast genomes.

This paper presents an overview of the principal structural and dynamics characteristics of reverse micelles (RMs) in order to highlight their structural flexibility and versatility, along with the possibility to modulate their parameters in a controlled-manner. The multifunctionality in a large range of different scientific fields is exemplified in two distinct directions: a theoretical model for mimicry of biological microenvironment and practical application in the field of nanotechnology and nano-based sensors. RMs represents a convenient experimental approach that limits the drawbacks of the conventionally biological studies in vitro, while the particular structure confers them the status of simplified mimics of cells by reproducing a complex supramolecular organization in an artificial system. The biological relevance of RMs is discussed in some particular cases referring to the confinement and crowding environment, molecular dynamics of water and cell membrane structure. The use of RMs in different range of applications seems to be more promising due to their structural and compositional flexibility, a high efficiency and selectivity being achieved. The advance in nanotechnology is based on developing new methods of nanomaterials synthesis and deposition. This review highlighting the advantages of using RMs in synthesis of nanoparticles with specific properties and in nano (bio)sensors design.

The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

Abstract: Radiation-induced skin injury can be a serious cutaneous damage and have specific characteristics. Asymptomatic periods are classified as the latent stage. The skin barrier plays a critical role in the modulation of skin permeability and hydration and protects the body against a harsh external environment. However, an analysis on the skin barrier dysfunction against radiation exposure in the latent stage has not been conducted. Thus, we investigated whether skin barrier is impaired by irradiation in the latent stage and aimed to identify the molecules involved in skin barrier dysfunction. We analyzed skin barrier function and its components in SKH-1 mice that received 20 and 40 Gy local irradiation. Increased transepidermal water loss and skin pH were observed in the latent stage of the irradiated skin. Skin barrier components, such as structural proteins and lipid synthesis enzymes in keratinocyte, increased in the irradiated group. Interestingly, we noted sebaceous gland atrophy and increased serine protease and inflammatory cytokines in the irradiated skin during the latent period. This finding indicates that the main factor of skin barrier dysfunction in the latent stage of radiation-induced skin injury is sebaceous gland deficiency, which could be an intervention target for skin barrier impairment.

Although the European reports highlight an increase in community-acquired Legionnaires’ disease cases, the risk of Legionella spp. in private houses is underestimated. In Pisa (Italy) we performed a three-year survey on Legionella presence in 121 buildings with an independent hot water production (IB); 64 buildings with a central hot water production (CB); and 35 buildings with a solar thermal system for hot water production (TB). From all the 220 buildings Legionella spp. was researched in two hot water samples collected either at the recirculation point or at on the first floor and on the last floor, while the potable water quality was analyzed in three cold water samples collected at the inlet from the aqueduct network, at the exit from the autoclave, and at the most remove remote? tap. Legionella pneumophila sg1, Legionella pneumophila sg2-16 and not-pneumophila Legionella species were detected in 26% of the hot water networks, mostly in CB and TB. In these buildings we detected correlations between the presence of Legionella and the total chlorine concentration decrease or/and the increase of the temperature. Cold water resulted free from microbiological hazards, with the exception of Serratia liquefaciens and Enterobacter cloacae isolated at the exit from two different autoclaves. We observed an increase in total microbial counts at 22 and 37°C between the samples collected at the most remote taps compared to the ones collected at the inlet from the aqueduct. The study highlights a condition of potential risk for susceptible categories of population and supports the need for measures of risk assessment and control.

The purpose of this paper is to provide empirical evidence to water policy-makers and the evaluation of the application of economic instruments such as price and other factors affecting demand, they contribute to improved decision-making around water management in the Biosphere Reserve El Vizcaino, Mexico. It was estimated a dynamic function with average price specification and other price perception specification. The findings show that consumers react to average price perceived and not the marginal price; long-run price elasticity is higher than short-run and both elasticities are inelastic. Elasticities inelastic with rising prices generate high incomes to improve water planning, supply quality and expand service coverage. The results suggest that the level of knowledge of users on the price is key to take into account restructuring rates in a scenario where the consumer has asymmetric information and themselves achieve goals of economic efficiency, social equity and environmental sustainability.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

The accuracy of estimating changes in terrestrial water storage (TWS) using Gravity Recovery and Climate Experiment (GRACE) level-2 products is limited by the leakage effect resulting from post-processing and the weaker signal magnitude in adjacent areas. TWS anomaly in Dnieper River basin, where characteristic with medium scale and adjacent weak TWS anomaly, is estimate in this work. Two categories of leakage error repaired method (including forward modeling, Data-driven, single and multiple scaling factor) are employed. Root mean square error (RMSE) and Nash-Sutcliffe Efficiency (NSE) are used to evaluate the efficiency of methods. Compare to independent methods, TWS anomaly inverted by multiple scaling factor depending on CPC Soil Moisture model is more accurate in terms with RMSE 2.32 and NSE 0.88, which scaling factors corresponding to trend term 1.02, annual term 1.04, and semi-annual term 1.14. Further, comprehensive climate insights behind of the TWS anomaly were confirmed. The temperate continental climate of this River basin is shown, according to the variation of TWS anomaly in spatial domain. Snowmelt is significant role in TWS anomaly of Dnieper River basin, which is accord with the precipitation record and the 14 years temperature spatial distribution of February. Overall, we compare TWS anomaly recovered by single and multiple scaling method, the leakage signal originates mainly from semi-annual term of the TWS anomaly.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

Drought is one of the most serious abiotic stressors in the environment, restricting agricultural production by reducing plant growth, development, and productivity. To investigate such a complex and multifaceted stressor and its effects on the plants, a systems biology-based approach is necessitated, entailing the generation of co-expression networks, identification of highly-priority transcription factors (TFs) dynamic mathematical modeling, and computational simulations. Here, we studied a high-resolution drought transcriptome of Arabidopsis. We revealed distinct temporal transcriptional signatures and demonstrated the involvement of specific biological pathways. Generation of a large-scale co-expression network followed by network centrality analyses identified 117 TFs that possess critical properties of hubs, bottlenecks, and high clustering coefficients nodes. Dynamic transcriptional regulatory modeling on integrated TF-target and transcriptome datasets uncovered major transcriptional events during the course of drought stress. Mathematical transcriptional simulations allowed us to ascertain the activation status of major TFs as well as the transcriptional intensity and amplitude of their target genes. Finally, we validated our predictions by providing experimental evidence of gene expression under drought stress for a set of four TFs and their major target genes using qRT-PCR. Taken together, we provided a systems-level perspective on the dynamic transcriptional regulation during drought stress in Arabidopsis and uncovered numerous novel TFs that can potentially be used in future genetic crop engineering programs.

Electrification coverage in Sarawak is the lowest at 78.74%, compared to Peninsular Malaysia at 99.62% and Sabah at 82.51%. Kapit, Sarawak with its 88.4% populations located in rural areas and mostly situated along the main riverbanks has great potential to generate electrical energy by hydrokinetic system. Yearly water velocity data is the most significant parameter to perform hydrokinetic analysis study. Nevertheless, the data retrieved from local river databases are inadequate for river energy analysis, thus hindering its progression. Instead, flow rates and rainfall data had been utilised to estimate the water velocity data. This signifies no estimation of water velocity in an unregulated river by using water level data had been made. Therefore, a novel technique of estimating the daily average water velocity data in unregulated rivers is proposed. The modelling of regression equation for water velocity estimation was performed and two regression model equations were generated to estimate both water level and water velocity on-site and proven to be valid as the coefficient of determination values had been R² = 87.4% and R²=87.9%, respectively. The combination of both regression model equations can be used to estimate long-term time series water velocity data for type-C unregulated river in remote areas.

The growing prevalence of disposable toilet seat covers in public restrooms stems from concerns about personal hygiene, given the direct contact between the seat and various users' skin. To enable flushing these disposable cover sheets down the toilet instead of discarding them in the trash, they must possess specific properties. These include rapid water absorption for quick disintegration, strength to endure user movement or moisture on the toilet seat surface, and a comfortable texture. To address these challenges, the study investigated the disintegration characteristics of flushable cover sheets prepared under different refining conditions. Alkyl ketene dimer (AKD) was also employed to enhance water resistance, while an organic antibacterial agent was used to impart antimicrobial properties. The findings revealed that adding 0.2% AKD and 1% organic antibacterial agent to pulp stock with a freeness of about 650 mL CSF was suitable for manufacturing disposable cover sheets with disintegration characteristics like toilet tissue paper.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

Bodybuilders utilize peaking strategies in a bid to fine-tune their aesthetics for competition day. The most prevalent peaking strategies utilized by natural bodybuilders are unreported in the current literature. Eighty-one (M - 59, F - 22) natural bodybuilders were recruited from competitions during the 2016 and 2017 British Natural Bodybuilder Federation seasons. Competitors completed a 34-item questionnaire designed to investigate peaking and contest day strategies. The questionnaire listed commonly utilized peaking strategies and provided additional space for qualitative information. Analysis of the data indicated that carbohydrate (CHO), water and sodium manipulation were the most commonly utilized peak week strategies. The consumption of high glycemic index CHO was the most common competition day strategy. Only 6.2 % of competitors reported following their regular diet the week prior to competition. The CHO manipulation strategies were similar to classical CHO loading, whereby bodybuilders attempt to maximize muscle glycogen concentrations. Furthermore, bodybuilders attempted to remove superfluous water by exploiting the diuretic/polyuria effect associated with water loading/restriction. The potentially deleterious effects of peaking on bodybuilders' health is considered and the efficacy of these strategies to enhance appearance is discussed. The findings of the present investigation are likely to be of interest to bodybuilders and their coaches.

A paddle wheel aerator is developed in this research, which includes a wireless sensor network for measuring the water quality in the aquaculture of marine shrimp ponds. It can also move to the desired position to fill oxygen and measure water quality. A basic requirement is good standard water quality to prevent shrimp from epidemics and improve production. The water quality paddle wheel aerator applies a microcontroller and sensors to measure eight parameters of water quality. These water quality parameters are observed on the web application via an IoT module. The movement system of the water-quality paddle wheel aerator consists of a LiDAR, GPS, and remote RF signal. Each item of data is recorded immediately on the cloud server while the water-quality paddle wheel moves in the marine shrimp farm. The controlled paddle wheel aerator is harnessed automatically to enhance precisely the spatial monitoring resolution of the measurement system installed, which is needless for a multiple measurement system with high cost of investment. Also, farmers can access real data through the Line application. Hence, they are able to plan and control a good environment for aquaculture, preventing the occurrence of various epidemics and decomposing organic matter in the pond.

Estimates of extreme water level return periods in river systems are crucial for hydraulic engineering design and planning. Recorded historical water level data of Taiwan’s rivers are not long enough for traditional frequency analyses when predicting extreme water levels for different return periods. In this study, the integration of a one-dimensional flash flood routing hydrodynamic model with the Monte Carlo simulation was developed to predict extreme water levels in the Danshuei River system of northern Taiwan. The numerical model was calibrated and verified with observed water levels using four typhoon events. The results indicated a reasonable agreement between the model simulation and observation data. Seven parameters, including the astronomical tide and surge height at the mouth of the Danshuei River and the river discharge at five gauge stations, were adopted to calculate the joint probability and generate stochastic scenarios via the Monte Carlo simulation. The validated hydrodynamic model driven by the stochastic scenarios was then used to simulate extreme water levels for further frequency analysis. The design water level was estimated using different probability distributions in the frequency analysis at five stations. The design high-water levels for a 200-year return period at Guandu Bridge, Taipei Bridge, Hsin-Hai Bridge, Da-Zhi Bridge, and Chung-Cheng Bridge were 2.90 m, 5.13 m, 6.38 m, 6.05 m, and 9.94 m, respectively. The estimated design water levels plus the freeboard are proposed and recommended for further engineering design and planning.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

Organic farming has positive, impact on environment, soil health, and healthy food quality. Worldwide demand for organic foods is increasing by leaps and bounds in recent years. The present investigation was undertaken during 2014 to 2018 to evaluate the effect of cowpea (Vigna unguiculata) co-culture with maize (Zea mays L.) on productivity enhancement over prevailing maize-fallow system, and to assess the feasibility of inclusion of short duration winter crops after maize with appropriate residue management practices on productivity and soil health. The experiment comprised of six cropping systems in main plot and three soil moisture conservation (SMC) measures options in sub plot. Results indicated that the inclusion of second crop in place of fallow and cowpea co-culture with maize increased average maize grain yield by 6.2 to 23.5% as compared to that of maize-fallow (MF). Use of maize stover mulch (MSM) + weed biomass mulch (WBM) increases maize grain yield by 19.1 and 6.5% over those of MSM and no mulch (NM), respectively. Various soil moisture conservation (SMC) measures had significant (p=0.05) effect on crop yields and water productivity. Double cropping system had significantly (p=0.05) higher amount of soil available NPK, soil organic carbon (SOC), microbial biomass carbon (MBC) and dehydrogenase activity (DHA) at 0-15 cm and at 15-30 cm depth than those under MF. The SWC measures of MSM+WBM had significantly higher available N, SOC, and MBC by 5.5, 4.8 and 8.1% than those under NM, respectively. Correspondingly, soils under MSM and MSM+WBM had 2.24 and 2.99% lower bulk density (ρb) in 0-15 cm and 2.21 and 2.94% lower ρb in 15-30 cm than that of NM. The energy use efficiency (EUE) was significantly higher under MCV (7.90%) over rest of the cropping sequences. MSM+WBM and MSM recorded 25.1 and 16.6% higher net energy over NM, respectively. The net return (INR 159.99×103/ha) and B:C ratio (2.86) were significantly higher with MCV system followed by MCR cropping sequence. MSM+WBM had significantly higher net return (INR 109.44×103/h), B:C ratio (2.46) over those under MSM (INR 97.6×103/h) and NM (INR 78.61×103/h). Overall the cowpea co-culture with maize and inclusion of short cycle winter crops along with MSM+WBM in maize-based cropping systems was found productive in terms of crop and water, profitable, energy efficient and sustained the soil health.

Soil erosion seriously affects vineyards. In this study, the influence of two plant covers on soil moisture and the effect of different physiographic conditions on runoff and sediment yields were evaluated in a rainfed vineyard formed by four fields (NE Spain) during 15 months. One field had spontaneous vegetation as plant cover and three fields had a cover crop of common sainfoin. The vineyards’ rows were dry and stable, whereas the inter-row areas were wet although very variable, and the corridors were wet and very stable. Soil moisture in the inter-row areas with Common sainfoin was much higher than in the rows (62% - 70%) whereas this difference was lower with spontaneous vegetation (40%). Two runoff and sediment traps (STs) were installed in two ephemeral gullies, and 26 time-integrated surveys (TIS) done. The mean and maximum runoff yields were 9.8 and 30.7 l TIS^–1 in ST2 and 13.5 and 30.2 l TIS^–1 in ST3. The mean turbidity was 333 and 19 g l^–1, and the maximum sediment yields were 41,260 and 2,778 g TIS^–1 in ST2 and ST3. Changes in the canopy covers (grapevines and plant covers) and rainfall parameters explained the runoff and sediment dynamics.

Agriculture technical development exclusively relies on the effective delivery of agrochemicals and water to the plants and reduce the harmful effects of the agrochemicals on the useful organisms in the soil. Wherefore, super absorbent hydrogels were prepared by copolymerization of gum Arabic (GA) with chitosan (CS) or poly(vinyl alcohol) (PVA), and cross-linked by N,’N-methylenebisacrylamide (MBA) chemically (CH) or using sodium hexametaphosphate (SHMP) as physical (PH) cross-linker. The prepared hydrogels include PVA/GA-CH, PVA/GA-PH, CS/GA-CH and CS/GA-PH showed different degree of swelling (DS) in the following swelling medium, deionized water (DW), river water(RW) and buffer solution pH9. PVA/GA-CH and CS/GA-CH hydrogels have showed 84g/g and 63g/g maximum DS in RW respectively, while PVA/GA-PH and CS/GA-PH hydrogels have showed 81g/g and 69g/g maximum DS in pH9 respectively. The water- retention capability of some hydrogels were studied using a mixture of 0.5%(w/w) hydrogel in agricultural soil and the composite showed about 20 days extra retain of water with a control sample of soil alone. The hydrogels were loaded using urea the important fertilizer in agriculture field. The hydrogels of higher DS were only loaded, where PVA/GA-CH hydrogel has shown 89%(w/w) maximum loading percentage (Lmax%), and CS/GA-PH hydrogel reached 79.75%(w/w) of urea. The release behavior in different medium and degree of temperatures of loaded hydrogels were studied. Generally, PVA/GA-CH hydrogel have shown better release profile in RW medium at 10oC, while CS/GA-PH hydrogel showed more controlled release in pH9 medium at 30oC. Different analytical methods of SEM, FTIR of loaded hydrogel and after their release were achieved, whereas XRD,1H NMR and (TGA, DSC) of prepared hydrogels have been characterized.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

The changing dynamics in climate is the primary and important determinant of agriculture productivity. The effects of this changing climate on overall productivity in agriculture can be understood when we study the effects of individual components contributing to the changing climate on plants and crops. Elevated CO₂ (eCO₂) and drought due to high variability in rainfall is one of the important manifestations of the changing climate. There is a considerable amount of literature that addresses climate effects on plant systems from molecules to ecosystems. Of particular interest is the effect of increased CO₂ on plants in relation to drought and water stress. As it is known that one of the consistent effects of increased CO₂ in the atmosphere is increased photosynthesis, especially in C₃ plants, it will be interesting to know the effect of drought in relation to elevated CO₂. The potential of elevated CO₂ ameliorating the effects of water deficit stress is evident from literature suggesting that these two are agents are brothers in arms protecting the plant from stress rather than partnering in crime, specifically water deficit when in isolation. The possible mechanisms by which this occurs will be discussed in this minireview. Interpreting the effects of short-term and long-term exposure of plants to elevated CO₂ in the context of ameliorating the negative impacts of drought will show us the possible ways by which there can be effective adaption to crops in the changing climate scenario.

Degraded soils causing from natural and human affects are universal in arid and semi-arid regions all over the world. Bentonite and humic acid (BHA) are increasingly being tested to remediate these degraded lands with potential benefits on crop production and soil health. The objective of this paper was to determine the residual effects four to five years after a one-time BHA application at six rates on (i) dynamic changes in soil properties, and (ii) oat crop productivity parameters, in a dryland farming ecosystem. With increasing rates of one-time BHA application, soil profile water storage displayed a piecewise linear increase plus plateau, whereas soil electrical conductivity, pH and bulk density were all reduced significantly (P < 0.05) in the 0-20 cm and 20-60 cm layers. The improved soil environments gave rise to an increased activity of soil enzymes urease, invertase and catalase that respectively reached the peak values of 97%, 37% and 32% at the rates of 21 to 24 Mg BHA ha-1. These conversely boosted soil nutrient turnover, leading to a 40% higher soil available P. Compared with the control treatment, application of BHA at the estimated optimum rate (roughly 24 Mg ha-1) increased grain yield by 20%, protein yield by 62%, water use efficiency by 41%, and partial factor productivity of N by 20%. Results of this study showed for the first time that a one-time BHA application would be a new and effective strategy to combat land degradation, drought, and promote a sustainable soil micro-ecological environment in dryland agroecosystem under a varying climate scenario.

Whereas a vast literature exists on satellite-based mapping of rice paddy fields in Asia, where most of the global production takes place, little has been produced so far that focuses on the European context. Detection and mapping methods that work well in the Asian context will not offer the same performances in Europe, where different seasonal cycles, environmental contexts, and rice varieties make distinctive features dissimilar to the Asian case. In this context, water management is a key clue; watering practices are distinctive for rice with respect to other crops, and within rice there exist diverse cultivation practices including organic and non-organic approaches. In this paper, we focus on satellite-observed water management to identify rice paddy fields cultivated with a traditional agricultural approach. Building on established research results, and guided by the output of experiments on real-world cases, a new method for analysing time series of Sentinel-1 data has been developed, which can identify traditional rice fields with a high degree of reliability. This work is a part of a broader initiative to build space-based tools for collecting additional pieces of evidence to support food chain traceability; the whole system will consider various parameters, whose analysis procedures are still at their early stages of development.

Here, we report on ZnO nanoparticles (NPs) generated by nanosecond pulsed laser (Nd:YAG, 1064 nm) through ablation of metallic Zn target in water and air and their comparative analysis as potential nanomaterials for biomedical applications. The prepared nanomaterials were carefully characterized in terms of their structure, composition, morphology and defects. It was found that in addition to the main wurtzite ZnO phase, which is conventionally prepared and reported by others, the sample laser-generated in air also contained some amount of monoclinic zinc hydroxynitrate. Both nanomaterials were then used to modify model wound dressings based on biodegradable poly-L-lactic acid. The as-prepared model dressings were tested as biomedical materials with bactericidal properties towards S. aureus and E. coli strains. The advantages of the NPs prepared in air over their counterparts generated in water found in this work are discussed.

Mediterranean coastal lagoons and their peripheral areas often provide a collection of habitats for many species, and they often face significant threats from anthropogenic activities. Diverse human activities in such areas directly affect the spatio-temporal dynamic of surface water and its ecological characteristics. Monitoring the surface water dynamic, and understanding the impact of human activities are of great significance for coastal lagoon conservation. The Regional Natural Park of Narbonne includes a typical Mediterranean lagoon complex where surface water dynamic and its potential link with local diverse human activities has not yet been studied. In this context, based on all the available Landsat images covering the study area during 2002-2016, this study identified the water and non-water classes for each satellite observation by comparing three widely used water indices (i.e., NDVI, NDWI and MNDWI) and using the Otsu method. The yearly water frequency index was then computed to present the spatio-temporal dynamic of surface water for each year, and three water dynamic scenarios were also identified for each year: permanent water (PW), non-permanent water (NPW) and non-water (NW). The spatial and inter-annual variation in the patterns of the three water scenarios were characterized by computing the landscape metrics at scenario-level quantifying area/edge, shape, aggregation and fragmentation. Finally, the quantitative link between different land use and land cover (LULC) types derived from the LULC maps of 2003, 2012 and 2015 and the surface water dynamic scenarios was established in each of the 300 m x 300 m grid cells covering the study area to determine the potential impact of human activities on the surface water dynamic. In terms of the inter-annual variation during 2002-2016, PW presented an overall stability, and NPW occupied only a small part of the water surface in each year and presented an inter-annual fluctuation. NPW had a smaller patch size, with lower connectivity degree and higher fragmentation degree. In terms of spatial variation during 2002-2016, NPW often occurred around PW, and its configurational features varied from place to place. Moreover, PW mostly corresponded to natural lagoon, and salt marsh (as a part of lagoons), and NPW had a strong link with arable land (agricultural irrigation) and salt marsh (salt production), sand beach/dune, coastal wetlands and lagoon for the LULC maps of 2003, 2012 and 2015. However, more in-depth analysis is required for understanding the impact of sand beach/dune, coastal wetlands and lagoon on surface water dynamics. This study covers the long-term variations of surface water patterns in a Mediterranean lagoon complex having intense and diverse human activities, and the potential link between LULC types and the water dynamic scenarios was investigated on different dates. The results of the study should be useful for environmental management and protection of coastal lagoons.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

Two different silica conformations (Xerogels and Nanoparticles) both formed by the mediation of dendritic poly (ethylene imine) were tested at low pHs on the problematic uranyl cation sorption. The effect of crucial factors i.e., temperature, electrostatic forces, adsorbent composition, accessibility of the pollutant to the dendritic cavities and MW of the organic matrix was investigated to conclude the optimum formulation for water purification under these conditions. This was attained with the aid of UV-Visible and FTIR spectroscopy, dynamic light scattering (DLS), ζ-potential; Brunauer–Emmett–Teller (BET) porosimetry, Thermo Gravimetric Analysis (TG) and Scanning Electron Microscopy (SEM) Results highlighted that both adsorbents have extraordinary sorp-tion capacity. Xerogels are cost-effective since they approximate the performance of na-noparticles with much lesser organic content. Furthermore, they are more practicable materials since they may penetrate the pores of a metal or ceramic solid substrate in the form of a precursor, gel-forming solution.

This article reviews all the major stages in the origins of life. From the emergence of matter in the initial Big Bang to the modern, civilized human being. On an immaterial level, it is proposed and explained how consciousness necessarily takes precedence over matter. Next, we explain how consciousness, with its ability to process information, selected the water molecule to breathe life into the periodic table of elements. We also explain why the notion of entropy allows us to evolve: "Die Entropie der Welt strebt einem Maximum zu" (second principle) and, therefore, takes precedence over the notion of energy, which, on the contrary, encourages us to preserve what we have: "Die Energie der Welt bleibt konstant" (first principle). This is followed by a discussion of the importance of quantum coherence and the need to rely on a second quantization formalism for a proper understanding of the physical-biochemical properties of water. Moreover, throughout the argument developed on the best and most fundamental things science has to offer, care is taken to link this knowledge to the great philosophies of the West (Greece), the East (China, India) or even to practices of a shamanic nature (Africa, America). Hence, finally, the proposal to reconsider all musical practice within the framework of the diapason of water at a frequency of 429.62 Hz, as well as all therapeutic practice on the basis of seven clearly identified and established frameworks of thought.

The extracts from the aerial parts of Helianthus salicifolius A. Dietr and Helianthus tuberosus L. collected in June were obtained using carbon dioxide supercritical fluid extraction with water as co-solvent. The antimicrobial activity in vitro of these extracts were determined against the reference species of Gram-positive and Gram-negative bacteria as well as fungi, representing by the yeast species of Candida spp. The following parameters were estimated: minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC). Both extracts were found to possess antimicrobial activity with MIC = 0.62-5 mg mL-1 for bacteria and MIC = 5-10 mg mL-1 for yeasts, showing bactericidal (MBC/MIC = 2-4) or fungicidal effect (MFC/MIC = 1-2 ). The highest activity was observed against S. aureus ATCC 29213 (MIC = 0.62 mg mL-1 for H. salicifolius extract; MIC = 2.5 mg mL-1 for H. tuberosus extract). Bactericidal effect of both extracts against S. aureus ATCC 29213 was confirmed by time-kill assay. Higher antioxidant activity was found for H. tuberosus extract (EC50 = 0.332 mg mL-1) as compared to that of H. salicifolius (EC50 = 0.609 mg mL-1). The total polyphenol content (TPC) expressed as gallic acid equivalents (GAE) was 13.75 ± 0.50 mg GAE (g of H. salicifolius extract)-1 and 33.06 ± 0.80 mg GAE (g of H. tuberosus extract)-1. There was a correlation between the antioxidant potential of both extracts and TPC but not between antistaphylococcal activity and TPC. The obtained data suggest potential application of these extracts as the natural preparations with the biocidal activity, including those with antistaphylococcal activity. Besides, both extracts may be regarded as potential natural conservants in cosmetics as well as natural preservatives in food.

The main objective of this work was to evaluate the application of individual and ensemble machine learning models to classify malignant and benign breast masses using features from two-dimensional (2D) correlated spectroscopy spectra extracted from five-dimensional Echo Planar-Correlated Spectroscopic Imaging (5D EP-COSI) and Diffusion-weighted imaging (DWI). Twenty-four different metabolite and lipid ratios with respect to 2D diagonal peaks at 1.4ppm and 5.4ppm, and water from one-dimensional non-water-suppressed (NWS) spectra were used as the features. Additionally, water fraction, fat fraction and water-to-fat ratios from NWS spectra and apparent diffusion coefficients (ADC) from DWI were included. Nine most important features were identified using recursive feature elimination. XGBoost (AUC:93.0%, Accuracy:85.7%, F1-score:87.6%), GradientBoost (AUC:94.4%, Accuracy:87.0%, F1-score:89.4%), CatBoost (AUC:95.2%, Accuracy:86.9%, F1-score:88.4%) and RandomForest (AUC:92.2%, Accuracy:85.3%, F1-score:87.6%) were the best performing models. While the conventional biomarkers like choline, myo-Inositol, and glycine were statistically significant predictors, the key features contributing to the classification were ADC, 2D diagonal peaks at 0.9ppm, 2.1ppm and 2.3ppm, cross peaks between 1.4 and 0.9ppm, 4.3 and 4.1ppm, 2.1 and 1.4ppm and the triglyceryl-fat cross peak. The results highlight the contribution of the 2D spectral peaks to the model, and they demonstrate the potential of 5D EP-COSI for early breast cancer detection.

The smart management of water resources is an increasingly important topic in today's society. In this context, the paradigm of Smart Water Grids (SWGs) aims at a constant monitoring through a network of smart nodes deployed over the water distribution infrastructure. In such a way, a continuous assessment of water quality and state of health of the pipeline infrastructure can be achieved, allowing an early detection of leaks and water contamination. Acoustic wave-based technology has arisen as a viable communication technique among the nodes of the network. Such technology can be suitable to replace traditional wireless networks in SWGs, as the acoustic channel is intrinsically embedded in the water supply network. However, the fluid-filled pipe is one of the most challenging media to be employed for data communication. This paper aims at reviewing those works dealing with acoustic-based communication networks in real large-scale urban water supply networks. An overview on the characteristics, trends and design challenges of existing works is provided as a guideline for future research.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

The shallow water equations are widely applied for the simulation of flow routing in rivers and floodplains, as well as for flood inundation mapping. From a mathematical point of view, they are a hyperbolic system of nonlinear partial differential equations, whose numerical integration is sometimes computationally burdensome. For this reason, the interest of many researchers has been focused on the study of simplified forms of the original set of equations, which requires less computational effort. One of the most commonly applied simplifications consists in neglecting the inertial terms, which changes the hyperbolic model to a parabolic one. The effects of such a choice on the outputs of the simulations of flooding events are controversial and an important topic of debate. In the present paper, two numerical models, recently proposed for the solution of the complete and zero-inertia forms of the shallow waters equations, are applied to several unsteady flow routing scenarios. We simulate synthetic and laboratory studies, starting from very simple geometries and moving towards complex topographies. Analyzing the role of the terms in the momentum equations, we try to understand the effect, on the computed results, of neglecting the inertial terms in the zero-inertia formulation. We analyze the computational costs.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

In-depth insights into the profound impacts of climate change and human activities on water resources are garnered through the dynamic changes in surface water, a crucial aspect of effective water resource management and the preservation of aquatic ecosystems. This paper introduces an innovative approach employing the random forest algorithm for the systematic extraction and monitoring of surface water at large regional or national scales. This method integrates spectral bands, spectral indices, and digital elevation model data, offering a novel perspective on this critical task. A data filling model is proposed to mitigate the impact of missing data due to cloud cover. Leveraging the capabilities of the Google Earth Engine (GEE), detailed information on surface water dynamics during the rainy and dry seasons in the Yangtze River Basin (YRB) from 1991 to 2021 is extracted using Landsat time series imagery. The analysis encompasses spatial-temporal variation characteristics and trends, with a specific focus on the intricate interplay between the areal extent of surface water and hydro-meteorological factors in each sub-basin of the YRB. Importantly, this includes considerations of potential groundwater contributions to surface water. Key findings from our research include: (1) Achieving a remarkable overall accuracy of 0.96 ± 0.03 in obtaining reliable surface water datasets with the support of GEE. (2) Identifying significant trends, such as a noteworthy increase in rainy season surface water bodies (+248.0 km2·yr−1) and a concerning decrease in surface ice/snow cover during both rainy and dry seasons, with change rates of −39.7 km2·yr−1 and −651.3 km2·yr−1, respectively. (3) Uncovering the driving mechanisms behind these changes, revealing positive correlations between the areal extent of rainy season surface water bodies and precipitation, as well as negative correlations between surface ice/snow cover area and average surface skin temperature. It is crucial to note that these driving factors exhibit variation among secondary river systems, underscoring the complexity of surface water dynamics. Furthermore, comparative analyses with existing surface water products are conducted, contributing to a deeper understanding of the advantages and uncertainties inherent in our proposed extraction method. The proposed method for large-scale surface water extraction not only enhances the monitoring of spatio-temporal surface water dynamics in the YRB but also provides valuable insights for the sustainable utilization and protection of water resources, considering the potential role of groundwater in supplementing surface water.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

Water supply policy is closely linked to sustainability as it directly influences the conservation and management of vital natural resources. This policy focuses on developing regulations and designing various activities related to the preser-vation of water resources, which can promote both ecological and economic sustainability. This study focuses on the Challenges of the Israeli Water Sector in Times of Emergency. In a time of growing climate crisis and despite the global warming trend, Israeli citizens routinely enjoy a regular constant supply of clean fresh water, thanks to local desalina-tion plants. Establishment of the desalination plants has become a model of water management for many countries in an era of growing climate crisis. At the same time, Israel’s water sector is faced with challenges and threats related to earthquakes and various states of warfare and security confrontations. In such times of emergency, Israel’s water sector is particularly vulnerable to disruptions of the water infrastructure and it’s adequate operation, by both contamination of the water sources and damage to the desalination plants. This study examines the challenges of the Israeli water sec-tor that require it to contend with these emergency situations in an era of reliance on desalination plants. The research method combines analysis of statistical data extracted from Israel’s Central Bureau of Statistics, Government Water and Sewage Authority, and Meteorological Service, in addition to reading and analyzing primary documents generated by various government ministries and government organs related to Israel’s water policy. The research findings lead to the conclusion that public policy on managing the water sector, manifested in the development and establishment of water desalination plants, has resolved Israel’s water crisis, put an end to its dependency on the amount of precipitation and on natural water sources, and allowed an increase in water production to match the rise in consumption. Nonetheless, as successful as this public policy may be, it does not consider the possibility of extreme scenarios and does not develop the entire range of steps necessary to confront them, and thus undermines the ability of the Israeli water sector to provide its citizens with water in times of emergency.

Modeling the reaction time required for the removal of chemical oxygen demand (COD) from wastewater is important because can be an indicator of harmful pollutants that may pose risks to human health.. Here, we evaluate the use of an inverse artificial neural network (ANNi) to optimize the removal of COD from aqueous herbicide solutions using sonophotocatalysis as the treatment process.. This algorithm takes the operating conditions as input and estimates the optimal reaction time to reach the required effluent COD. This model was validated by comparison with both experimental measurements and simulated analysis, resulting in low error (0.5%), high Pearson correlation (R2 = 0.9956), and short computing time (less than one minute). The results for the proposed methodology (ANNi-GAs) were efficient and attractive in a reasonable way providing a satisfactory picture of the relationships between the optimal input parameters. Such parameters control the degradation process of herbicides online and can be used to predict the behavior of COD removal, thus taking actions to reduce the impact of aqueous treatment with alazine and gesaprim herbicides on aquatic, soil biota, and human health. Therefore, this technique constitutes a promising framework for predicting the environmental impact of herbicides within a tolerable degree of error.

Infill well location optimization poses significant challenges due to its complexity and time-consuming nature. Currently, determining the scope of infill wells relies heavily on field engineers' experience, often using single indices such as remaining oil saturation or abundance of remaining oil reserves to evaluate the potential of remaining oil. However, this approach lacks effectiveness in guiding the precise tapping of remaining oil in ultra-high water cut reservoirs. To address this, our study comprehensively considers factors influencing the recoverable potential of remaining oil in such reservoirs. We characterize differences in reservoir heterogeneity, the scale of recoverable remaining oil reserves, water flooding conditions, and oil-water flow capacity to construct a quantitative evaluation index system for the recoverable potential of remaining oil. Recognizing the varying degrees of influence of different indices on the recoverable potential of remaining oil, we determine the objective weight of each evaluation index by combining an accelerated genetic algorithm with the projection pursuit model. This approach enables the construction of a recoverable potential index for remaining oil and forms a quantitative evaluation method for the recoverable potential of remaining oil in ultra-high water cut reservoirs. Subsequently, we establish a mathematical model for infill well location optimization, integrating and optimizing infill well location coordinates, well length, well inclination angle, and azimuth angle. Using the main layer sand body of an oilfield in Bohai as a case study, we conducted evaluations of remaining oil potential and infill well location optimization. Results demonstrate that the assessment of remaining oil potential comprehensively characterizes the influence of reservoir physical properties and oil-water diversion capacity on remaining oil potential across different regional positions. This evaluation can effectively guide the determination of infill well location ranges based on the evaluation results. Furthermore, further optimization of infill well locations can effectively enhance reservoir development outcomes.

Multi-stakeholder participation processes in watershed management face challenges due to limited monitoring and baseline data, resulting in a lack of awareness among stakeholders about the current state of the watershed. This knowledge gap often leads to conflicts of interest, where the broader impacts of individual decisions are overlooked. To overcome these limitations, this paper explores the design and implementation of a Serious Game (SG) aimed at co-producing a watershed management plan at the basin scale within the specific context of the Campoalegre River basin in Colombia. By providing an interactive platform, the SG facilitates collaboration between local actors, who may be unfamiliar with existing watershed plans, and decision-makers. The goal is to create a participatory space where stakeholders can comprehend the watershed management plan structure and prioritize actions based on various climatic, social, and economic conditions. Following the application of the SGs, stakeholders demonstrated an improved understanding of the basin, fostering increased participation, open debate, and the proposal of actions. These outcomes serve as valuable inputs for the implementation of water management planning policies, showcasing the potential of SGs in bridging knowledge gaps, and fostering effective multi-stakeholder engagement.

In this work, a novel approach is presented for the multivariate prediction of hydrological variables, employing a specialized type of recurrent neural network (RNN) known as the long-term memory network (LSTM).The central objective is to develop a flood prediction model using data collected from two hydrological stations situated along the Atrato River in the Choc´o Department, Colombia. The interconnected variables of water level, water flow, and water precipitation are analyzed in this model to enhance flood prediction accuracy. The LSTM model, integrated into an RNN structure, is designed to capture the complex dynamics and cross-correlations inherent in these hydrological variables. Validation involves a comparison with linear and nonlinear Nonlinear AutoRegressive with eXogenous input (NARX) models, considering factors such as estimation error and computational time. Additionally, the study conducts further analysis for water level prediction under two scenarios: utilizing only outflow and inflow measurements or predicting outflow alongside measuring inflow, with the objective of utilizing the proposed approach as a flood early warning system. † This article is a revised and expanded version of a paper entitled Multivariable NARX based Neural Networks Models for Short-term Water Level Forecasting, which was presented at International Conference on Time Series and Forecasting (ITISE-2023), Gran Canaria, Spain, 12th-14th July, 2023.

This study addresses the prediction of recurring failures in water supply networks, a complex and costly task, but essential for the effective maintenance of these vital infrastructures. Using historical failure data provided by Companhia de Água e Esgotos da Paraíba (CAGEPA), the research focuses on predicting the time until the next failure at specific points in the network. The authors divided the failures into two categories: Occurrences of New Faults (ONF) and Recurrences of Faults (RF). To make the predictions, they used predictive models based on Machine Learning, more specifically on MLP (Multi Layer Perceptron) neural networks. The study revealed that, by analyzing data from past failures and considering factors such as altitude, number of failures on the same street and days between failures, it is possible to achieve an accuracy greater than 80% in predicting failures within a 90-day interval. This demonstrates the feasibility of using fault history to predict future water supply outages with significant accuracy. These forecasts allow water utilities to plan and optimize their maintenance, minimizing inconvenience and losses. The article contributes to the field of water infrastructure management by suggesting that the data-driven approach can be applied in other cities or in networks of different types, such as energy or communication networks. The conclusions highlight the importance of data collection and analysis in preventing failures and optimizing water utilities’ resources.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

In the field of climate change adaptation, the future matters. Amongst others, river futures justify the way adaptation projects materialize in rivers. In this paper, we challenge the ways in which dominant paradigms and expert claims monopolise the truth concerning policies and designs of river futures, side-lining and delegitimizing alternative river futures. Currently, limited work is done to critically reflect on the power of river futures in the context of climate change adaptation. We conceptualized the power of river futures through river imaginaries: collectively performed and publicly envisioned reproductions of riverine socionatures, mobilized through truth claims of social life and social order. Through the Border Meuse project case study, a climate change adaptation project in a stretch of the river Meuse in the south of the Netherlands and a proclaimed success story of climate adaptation in Dutch water management, we elucidated how three river imaginaries: a modern river imaginary, a market-driven imaginary and an eco-centric river imaginary, merged and materialized as an eco-modern river imaginary. Importantly, not only the river futures merged, also their aligned truth regimes merged. To this end, we argue that George Orwell’s famous quote “Who controls the past, controls the future: who controls the present, controls the past” can be extended to ‘Who controls the future, controls how we see and act in the present, and how we rediscover the past’.

The Southwest Alpine Canyon Area of China was one of the regions in the world that suffered from severe soil erosion. The focus of this research was to understand the response of land use change on soil loss by water erosion in alpine canyon on Southeast Tibet, we analyzed the characteristics of temporal and spatial dynamics of land use in the Niyang River Basin from 1990 to 2020 using GIS and statistical methods, assessed the spatial and temporal change characteristics of soil erosion in the Niyang River Basin using RUSLE model. For this purpose, the meteorological, soil, topographic, remote sensing data were collected. The results showed the area of cropland and construction land in the Niyang River Basin increased to 2.4 and 6.1 times the original from 1990 to 2020, respectively, the area of forest and water continued to decrease. Grassland, unused land and forest have always been the dominant land types in the Niyang River Basin. Tolerable soil erosion was distributed in the flat areas of the valley terraces in the main stream and its tributaries, slight soil erosion was mainly distributed in the flat areas at high altitudes, and moderate, severe, very severe and destructive soil erosion was sporadically distributed in the Niyang River Basin. The areas of tolerable and slight soil erosion exceeded 82% of the total area, The area of severe, very severe and destructive soil erosion was less than 6%, but the total soil loss amount of severe, very severe and destructive erosion was more than 27%. From 1990 to 2020, the soil erosion area decreased from 9219.34 km2 to 8,090.84 km2 in Niyang River Basin, more than 85% of the soil erosion class has not changed, and the change of total soil loss amount also shows a significant reduction trend as a whole. 99% of the total soil loss amount in the Niyang River basin is generated by grassland, forest and unused land. The conversion of various land use types to cropland will cause the enhancement in soil erosion grade. We recommend that the focus of soil erosion control in the Niyang River Basin is to protect grassland, forest and carry out scientific farming.

The state of Veracruz has ample water resources. However, due to population and industrial growth, there has been an increase in the discharge of wastewater into surface water bodies. To analyze the water quality in the Bobos River, Veracruz, and its sustainability, researchers collected nine samples from nine different points in the reservoir. They measured various parameters such as temperature, pH, dissolved oxygen, conductivity, total nitrogen, nitrate, chemical oxygen demand, total phosphorus, phosphate, dissolved solids, and fecal coliforms. The results showed that the river's water quality is at risk. The concentration of pollutants such as chemical oxygen demand and fecal coliforms is high. Conductivity values ranged from 0.26 to 3.81 mS. If preventive and corrective measures are not taken, the river's ability to purify pollutants will be severely compromised. This study evaluates the physical, chemical, and microbiological characteristics of the water in Bobos River. It specifically investigates the influence of the nearby citrus industry on the river's water quality. The study also aims to promote environmental sustainability.

Collagen is a triple-helical protein unique to the extracellular matrix, conferring rigidity and stability to tissues such as bone and tendon. For the [(PPG)10]3 collagen-mimetic peptide at room temperature, our molecular dynamics simulations show that these properties result in a remarkably ordered first hydration layer, of water molecules hydrogen-bonded to the backbone-carbonyl (bb-CO) oxygen atoms. This originates from the following observations. The radius of gyration attests that the PPG triplets are organized along a straight line, so that all triplets (excepting the ends) are equivalent. The solvent accessible surface area (SASA) for the bb-CO oxygens shows a repetitive regularity for every triplet. This leads to bb-CO⋯HOH occupancy following a similar regularity, similar also to the crystal-phase 0-2-1 water occupancy in the P-P-G triplet. The regularity is maintained in spite of the sub-nsec water exchange rate, because the bb-CO sites rarely remain vacant. The manifested ordered first-shell water molecules are expected to produce a cylindrical electrostatic potential around the peptide, that might guide cation diffusion in its vicinity.

Dye-containing effluent generated in textile industries is polluting and complex wastewater. It should be managed adequately before the final destination. The up-flow anaerobic blanket (UASB) reactor application is an eco-friendly and cost-competitive treatment. The present study briefly reviews the UASB application for dye wastewater valorization. Bioenergy and clean water production potential during dye-containing wastewater treatment are emphasized to promote resource recovery in textile industries. Efficiencies of color and chemical oxygen demand of 50–97% and 60–90% are reported in bench-scale UASB studies. A biogas yield of 0.36–36.04 L d-1 in UASB, which treats dye-containing effluents, is documented. Bioenergy production and water reuse allow environmental and economic benefits. However, data on full-scale UASB treating dye wastewater are missing. Besides, studies on combined systems integrating membrane processes, such as ultrafiltration and nanofiltration, and pretreatment of wastewater and sludge for improvements in biogas production might realize the complete potential for resource recovery of UASB technology.

Spatiotemporal climate variability is a leading environmental constraint to the rain-fed agricultural productivity and food security of communities in the Abbay basin and elsewhere in Ethiopia. The previous one-size-fits-all approach to soil and water management technology targeting did not effectively address climate-induced risks to rain-fed agriculture. This study, therefore, delineates homogenous climatic regions and identifies climate-induced risks to rain-fed agriculture that are important to guide decisions and selection of site-specific technologies for green water management in the Abbay basin. The k-means spatial clustering method was employed to identify homogenous climatic regions in the study area, while the Elbow method was used to determine an optimum number of the climate clusters. The k-mean clustering used the Enhancing National Climate Services (ENACTS) daily rainfall, minimum and maximum temperatures, and other derived climate variables that include daily rainfall amount, length of growing period (LGP), rainfall onset and cessation dates, and rainfall intensity, temperature, potential evapotranspiration (PET), soil moisture and AsterDEM to define climate regions. Accordingly, 12 climate clusters or regions were identified and mapped for the basin. Clustering a given geographic region into homogenous climate classes is useful to accurately identify and target locally relevant green water management technologies to effectively address local-scale climate-induced risks. The study has also provides a methodological framework that can be used in the other river basins of Ethiopia and indeed elsewhere.

Drought is one of the leading abiotic factors limiting morphological and physiological activities in blackberry cultivation. We investigated the effect of silver nanoparticles (AgNPs) on morphological and physiological processes in the boysenberry crop (Rubus ursinus Chamisso &amp; Schlenhtendal) under drought stress. The experiment was performed with three drought stress levels (0% PEG, 4% PEG and 8% PEG) and three AgNPs treatments (0, 0.1, 0.2 mg L−1) invitro conditions. The results showed that drought stress induced by PEG, reduced root and shoot development of boysenberry plants grown invitro. The addition of AgNPs is significantly alleviated the adverse effect of drought stress and increased the plant growth parameters. Antioxidant activity of SOD and CAT enzymes increased in boysenberry leaves when treated with AgNPs under drought conditions, while the amount of MDA decreased. Therefore, the results obtained in this study suggest that 0.1 mg L-1 AgNPs added to the medium improve the growth and development of invitro boysenberry plants under drought stress.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

Water quality assessments are crucial for human health and environmental safeguards. The utilization of a subset of artificial intelligence such as Machine Learning (ML) presents significant impacts to enhance the prediction and classification of water quality. In this research, a set of diverse ML algorithms was evaluated to handle a comprehensive dataset of water quality measurements over an extended period. The aim was to develop a robust approach for accurately forecasting water quality. This approach employed machine learning classifiers such as Logistic Regression (LR), Support Vector Machine (SVM), Stochastic Gradient Descent (SGD), K-Nearest Neighbors (KNN), Gaussian Process Classification (GPC), Gaussian Naive Bayes (GNB), Random Forest (RF), Decision Tree (DT), XGBoost, and Multilayer Perceptron (MLP). The water quality parameters assessed for pH, hardness, solids, chloramines, sulfate, conductivity, organic carbon, trihalomethanes and turbidity. The XGBoost model exhibited the highest accuracy of 89.47% among the classifiers and Stacked Ensemble Classifiers (SEC) improved the prediction further to 92.98%. The findings suggest that XGBoost and the SEC hold promise as reliable approaches for water quality assessments in contrast of artificial intelligence.

Bisphenol A is a remarkable chemical compound for its many applications mainly in the plastics industry, but also for its toxic effects on the environment and human health. BPA (4,4-isopropylidenediphenol) is an anthropogenic compound, moderately soluble in water (120 – 300 mg/l) at room temperature, and highly soluble in alkaline solutions, ethanol and acetone. BPA can bioconcentrate, bioaccumulate and biomagnify through food webs until it reaches humans. To prevent this, effective strategies are sought to allow its removal from the environment, through physico-chemical or enzymatic methods, advanced oxidation, adsorption and biodegradation, ultrasonic degradation. This article shows a comparative study regarding adsorption of BPA on Active carbon and zeolitic tuff, ZTC. In this paper, the characterization of the zeolitic tuff Rupea adsorbent, was carried out from an elemental and mineralogical point of view, pore size and elemental distribution, using SEM, EDAX, and XRD analysis. The pore size varies from 30 nm to 10 µm, atomic ratio Si/Al≥4, and the 80 % of mineralogical composition represent Ca Clinoptilolite zeolites Ca Clinoptilolite zeolite ((Na1.32K1.28Ca1.72Mg0.52)(Al6.77Si29.23O72)(H2O)26.84). Also, a comparative study of the adsorbtion capacity of bisphenol A from synthetic solutions on activated carbon type - Norit GAC 830 W, GAC, as well as on Clinoptilolite-type zeolitic tuff, ZTC, Rupea, was carried out. The experiments were carried out at a temperature of 20 ºC, a pH of 4.11; 6.98 and 8.12, and ionic strength being assured using KCl of 0.01 M, and 0.1 M. The adsorption capacities of GAC and ZTC tend to 115 mg/g and 50 mg/g respectively, at 8.12 pH and ionic strength of 0 M. The Langmuir mathematical model most faithfully describes the adsorption equilibrium of BPA. The maximum adsorption capacity for both adsorbents increases with increasing pH, and decreases with increasing ionic strength.

Despite a growing concern over sustainability in tourism, research on this domain regarding, specifically, lake destinations, is still scarce. Although perceptions on lake destinations have been studied, no study is known that analyses the impact of visitors’ perceptions on satisfaction and behavioral intentions. Thus, this paper aims to develop and test a model to analyse the effect of lake visitors’ perceptions of destination’s sustainability on both satisfaction and loyalty towards lake destinations. A questionnaire survey was conducted in the Shchuchinsk-Burabay resort area, an important lake destination in northern Kazakhstan. The results support the proposed lake destination loyalty model, tested using partial least squares structural equation modelling (PLS-SEM). Sustainability proved to be decisively influential, with water quality being the dimension with the highest impact on satisfaction with the lakes, along with a positive key impact of the absence of congestion. In addition, both water quality and lack of congestion had a significant indirect impact on satisfaction with the lake destination, and on loyalty. Based on the research findings, theoretical conclusions and practical implications are drawn.

Βottom-up management in catchment scale is deemed as the determinant way to avoid the conflict of the water users through the participation of stakeholders, strategy co-shaping and solutions co-creation. Water management cannot be one-dimensional but demands cross sectoral coop-eration. Usually, the difficulty lies in proper stakeholder training and their opinion inclusion, using a quantifiable manner in water management. The Laspias River watershed occupies an area of 221.8 km2, belonging to the River Basin District of Thrace and it is characterized by intense agricultural and industrial activity. Complying with the augmented water needs and pollution loads by respecting stakeholders’ opinion, this research aims to utilize a hybrid intuitionistic fuzzy multi-criteria-based methodology. It is a common difficulty to deal with supplier selection in resources management since it is a typically decision-making problem encompassing multiple (several conflicting) criteria, on which stakeholder’s opinions are usually imprecise and in a rather qualitative form. Therefore, the proposed method provides the mathematical tool to move into more comprehensive decisions with the public involvement. The weights are produced based on the stakeholder’s opinion. The alternatives’ ranking is achieved based on the fuzzified intuition-istic version of Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) and problems’ mitigation solutions’ hierarchy is achieved.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

With the rapid development of urbanization, the chemical evolution of groundwater is significantly affected by human activities. However, the driving mechanisms of groundwater chemical evolution at different stages of urbanization remain unclear, severely impacting the implementation of groundwater protection. This study investigated the driving mechanisms of groundwater chemical evolution based on the long-term series (from 1985 to 2015) of hydrochemical data from 19 groundwater monitoring sites in rapidly urbanizing areas (Shijiazhuang, Hebei Province, China). The results show that the concentrations of various chemical components in groundwater gradually increase with the acceleration of urbanization process, especially NO3-, which has increased from 13.7 mg/L in the primary stage of urbanization (PSU) to 65.1mg/L in the advanced stage of urbanization (ASU), exceeding the WHO drinking water standard (50mg/L), indicating that the groundwater chemistry has been significantly affected by human activities. It is interesting to find that the main hydrochemical types have changed from HCO3•SO4-Ca•Mg type water in the PSU to SO4•HCO3-Ca•Mg type water in the ASU. It is worth noting that there were obvious differences in driving factors of groundwater chemical evolution at different urbanization stages. In the PSU, the driving factors of groundwater chemical evolution were carbonate and rock salt dissolution, cation exchange, and industrial activities. However, in the intermediate stage and advanced stage, the driving factors of groundwater chemical evolution were changed to carbonate and gypsum dissolution, groundwater over-exploitation, agricultural fertilization, and domestic sewage. Based on the above conclusions, it is suggested that future groundwater management should control the amount of agricultural fertilizers, apply scientific fertilization, and prohibit the discharge of various types of non-compliant sewage, while strengthening the supervision of groundwater extraction to reduce the impact of urbanization development on the groundwater chemical evolution process.

In this paper an overview of waste materials in underground coal mines is presented, whereas waste materials can be of anthropogenic or geogenic origin. Complex interactions with mine water and waste materials take place, especially during mine water level rebound. Bearing in mind that under the increasing societal pressure most, if not all underground coal mines are going to be closed rather sooner than later, it is important to understand these interactions and to predict the composition and dynamics of mine water lever rebound in underground coal mines to prevent adverse effects to the environment, especially receiving waters and drinking water resources. The second part of this article focusses on the experiences gained in the Ruhr area, a closed underground coal mining region in Western Germany, where mine water rebound has been ongoing for decades. In this regard, the modelling program DMT-Boxmodel has been developed and applied to predict the hydrodynamics and hydrogeochemical development of the water rebound. As an example, simulation results of water rebound as well as solute and PCB transport in central province of Ruhr mining area are compared to the monitoring data, and predictions over 3 decades are given. The experiences gained in the mine water management in Ruhr area can be applied in mining areas worldwide.

Evaluating the performance of water indices and mapping the spatial distribution of water-related ecosystems are important for monitoring surface water resources. This is particularly the case for Ethiopia since there is limited information available on water resources development over time despite its relevance for the people and ecosystems. To address this problem, this paper evaluates the performance of seven water indices for country-scale surface water detection based on high spatial and multi-temporal resolution Sentinel-2 data, processed using the Google Earth Engine cloud computing system. Results show that the water index (WI) and automatic water extraction index with shadow (AWEIsh) are the most accurate ones to extract surface water. Comparisons are based on qualitative visual inspections and quantitative accuracy indicators. For the latter, WI and AWEIsh obtained kappa coefficients of 0.96 and 0.95, respectively, and an overall accuracy of 0.98 each. Both indices accounted for similar spatial coverages of surface waters with 82,650 km2 (WI) and 86,530 km2 (AWEIsh) for the whole of Ethiopia.

Background: Instrument-assisted soft tissue mobilization (IASTM) is thought to alter fluid dynamics in human soft tissue. The aim of this study was to investigate the influence of IASTM on the thoracolumbar fascia (TLF) on the water content of the lumbar myofascial tissue. Methods: 21 healthy volunteers were treated with IASTM. Before and after the procedure and 5 and 10 minutes later, lumbar bioimpedance was measured by bioimpedance analysis (BIA) and TLF stiffness by indentometry. Tissue temperature was recorded at the measurement time points using an infrared thermometer. Results: Bioimpedance increased significantly from 58.3 to 60.4 Ω (p < 0.001) at 10-minute follow-up after the treatment. Temperature increased significantly from 36.3 to 36.6° Celsius from 5 to 10 minutes after treatment (p = 0.029), while lumbar myofascial stiffness did not change significantly (p = 0.84). Conclusions: After the IASTM intervention, there was a significant increase in bioimpedance, likely due to a decrease in water content in myofascial lumbar tissue. Further studies in a randomized control trial design are needed to extrapolate the results in healthy subjects to a symptomatic population as well and to confirm the reliability of BIA in myofascial tissue.

River flow prediction is a pivotal task in the field of water resource management during the era of rapid climate change. The highly dynamic and evolving nature of the climatic variables e.g., precipitation has a significant impact on the temporal distribution of the river discharge in recent days making the discharge forecasting even more complicated for diversified water-related issues e.g., flood prediction and irrigation planning. To predict the discharge, various physics-based numerical models are used using numerous hydrologic parameters. Extensive lab-based investigation and calibration are required to reduce the uncertainty involved in those parameters. However, in the age of data-driven predictions, several deep learning algorithms showed satisfactory performance in dealing with sequential data. In this research, Long Short-term Memory (LSTM) neural network regression model is trained using over 80 years of daily data to forecast the discharge time series up to 3 days ahead of time. The performance of the model is found satisfactory through the comparison of the predicted data with the observed data, visualization of the distribution of the errors and Root Mean Squared Error (RMSE) value of 0.09. Higher performance is achieved through the increase in the number of epochs and hyper parameter tuning. This model can be transferred to other locations with proper feature engineering and optimization to perform univariate predictive analysis and potentially be used to perform real-time river discharge prediction.

The thermodynamic phase behavior of charged polymers is a crucial property underlying their role in biology and various industrial applications. A complete understanding of the phase behaviors of such polymer solutions remains challenging due to the multi-component nature of the system and the delicate interplay among various factors, including the translational entropy of each component, excluded volume interactions, chain connectivity, electrostatic interactions, and other specific interactions. In this work, the phase behavior of partially charged, ion-containing polymers in polar solvents is studied by further developing a liquid-state (LS) theory with local short-range interactions. This work is based on the LS theory developed for fully-charged polyelectrolyte solutions. Specific interactions between charged groups of the polymer and counterions, between neutral segments of the polymer, and between charged segments of the polymer are incorporated into the LS theory by an extra Helmholtz free energy from the perturbed-chain statistical associating fluid theory (PC-SAFT). The influence of the sequence structure of the partially charged polymer is modeled by the number of connections between bonded segments. The effects of chain length, charge fraction, counterion valency, and specific short-range interactions are explored. A computational App for salt-free polymer solutions is developed and presented, which allows easy computation of the binodal curve and critical point by specifying values for the relevant model parameters.

Hazardous chemicals like toxic organic dyes are very harmful to the environment and their removal is quite challenging. Therefore there is a necessity to develop techniques, which are environment friendly, cost-effective and easily available in nature for water purification and re-mediation. The present research work is focused on the development` and characterization of the ecofriendly polyvinyl alcohol (PVA) and alginate (Alg) hydrogel beads incorporating natural bentonite (Bent) clay as beneficial adsorbents for removal of toxic methylene blue (MB) from industrial water. PVA−Alg/Bent nanocomposite hydrogel beads with different Bent content (0, 10, 20, and 30 wt%) were synthesized via external ionic gelation method. The designed porous and steady structure beads were characterized by the use of Fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDX), and scanning electron microscopy (SEM). The performance of the beads as MB adsorbents was investigated by treating batch aqueous solutions. The experimental results indicated that the incorporation of Bent (30 w%) in the nanocomposite formulation sustained porous structure, preserved water uptake, and increased MB removal effi-ciency by 230 % compared to empty beads. Designed beads possessed higher affinity to MB at high pH 8, 30 °C, and fitted well to pseudo-second-order kinetic model a high correlation coefficient. Moreover, designed beads had a good stability and reusability as they exhibited excellent removal efficiency (90%) after six consecutive adsorption-desorption cycles. Adsorption process was found be combination of both monolayer adsorption on homogeneous surface and multilayer adsorption on heterogeneous surface. The maximum adsorption capacity of the designed beads system as calculated by Langmuir isotherm was found to be 51.34 mg/g, which is in good agreement with the reported clay-related adsorbents. The designed PVA−Alg/Bent nanocomposite hydrogel beads demonstrated good adsorbent properties and could be potentially used for MB removal from polluted water.

Well placement optimization in a given geological setting for a fractured geothermal reservoir is a prerequisite for enhanced geothermal operations. High computational cost associated in the framework of fully coupled thermo-hydraulic-mechanical (THM) processes in a fractured reservoir simulation, makes the well positioning as a missing point in developing a field scale investigation. Here, in this study, we shed light on this topic through examining different injection-production well (doublet) position in a given real fracture network. Water and CO2 are used as working fluids for geothermal operations and importance of well positions are examined using coupled THM numerical simulations for both the fluids. Results of this study are examined through the thermal breakthrough time, mass flux and the energy extraction potential to assess the impact of well position in a two-dimensional reservoir framework. Almost ten times of the difference between the final amount of heat extraction is observed for different well position but with the same well spacing and geological characteristics. Furthermore, stress field is be a strong function of well position that is important with respect to the possibility of unwanted stress development. As part of the MEET project, this study recommends to perform similar well placement optimization study for each fracture set in a fully coupled THM manner before a field well drilling.

Groundwater monitoring and water level predictions have been a challenging issue due to the complexity of groundwater movement. Simplified numerical simulation models have been used to represent the groundwater system; these models however only provide the conservative approximation of the system and may not always capture the local variations. Several other efforts such as coupling groundwater models with hydrological models and using geostatistical methods are being practiced to accurately predict the groundwater levels. In this study, we present a novel application of geostatistical tool on residuals of groundwater model. Kriging method was applied on the residuals of the numerical model (MODFLOW) generated by the TWDB (Texas Water Development Board) for the Edwards-Trinity (Plateau) aquifer. The study was done for the years 1995 through 2000 where 90% of the observation data was used for model simulation followed by cross-validation with the remaining 10% of the observations. The kriging method reduced the average absolute error of approximately 31 m (for MODFLOW simulation) to less than 5 m. Also, the residuals’ average standard error reduced from 9.7 to 4.7. This implies that the mean value of residuals over entire period can be a good estimation for each year separately. The use of kriging technique thus can provide with improved monitoring of groundwater levels resulting in more accurate potentiometric surface maps.

Permeable pavements have been the subject of numerous studies in recent decades. The possibility of dissipating stormwater more smoothly and generating numerous benefits to the environment and users makes the use of permeable pavements an excellent possibility of integration into sustainable and resilient water management systems in cities. In Brazil, numerous studies on the quantity and quality of infiltrated water, permeability of the coating, clogging, environmental burden, feasibility, among other characteristics, have been researched. Within this theme, the Federal University of Santa Catarina (UFSC) has contributed with ten papers in the research of permeable pavements in the last six years, which address various topics about the effectiveness and applicability of permeable pavements. This paper reviews the studies conducted at UFSC on permeable pavements and discusses the different results within the main issues found. In general, the selected documents addressed seven themes in the studies: potential for potable water savings, clogging, quantity and quality of the water infiltrated into the pavement, Life Cycle Assessment (LCA) and its variants, and hydraulic and structural design details. More specifically, many selected papers assess the potential use of stormwater harvested through permeable pavements in non-potable uses of buildings. The possibility of aligning the benefits of green infrastructure with the rational use of water expands the advantages of the system and can help prevent future water scarcity, as well as reduce the environmental impacts of paving.

A complete halt on all anthropogenic activities and human movement due to COVID-19 lockdown has provided a great opportunity to assess the impact of human activities on coastal marine ecosystems. The current study assessed the concentration of the metals in water samples of the largest brackish water lagoon of Asia; the Chilika lagoon in the state of Odisha, India between pre-COVID-19 and post-COVID-19 lockdown scenarios. Monthly water samples (n=30 stations) from 0.3 m depth were collected from three sectors of the lagoon seasonally; pre-monsoon, monsoon, and post-monsoon. In addition to various physical parameters [pH, salinity, alkalinity, (DO) dissolved oxygen, (TDS) total dissolved solids, and (EC) electrical conductivity] the collected water samples were analysed for 18 trace metals (Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sr, Th, Tl, U, V). Most of the physical parameters showed a significant variation between pre-and post-COVID-19 scenarios, except for pH and DO. The concentration of five metals (Be, Cd, Co, Ni, and Pb) remained below detection limits in all water samples. The impact of COVID-19 lockdown on the concentration of the metal in the water samples was noticed along with the three sectors of the lagoon. However, eight metals (Al, As, Cr, Fe, Mn, Th, U, and V) were significantly different between the COVID-19 scenarios and the remaining five metals were not statistically significant. The mean concentration of Al, As, Fe, Th, and V were higher in the pre-COVID-19 scenarios, whereas only Cr and Mn were higher in the post-COVID-19 scenarios. The mean concentration of U was similar among both COVID-19 scenarios, even though there were seasonal and sectoral differences. The seasonal influence of riverine influx was more evident on metal concentration during the monsoon season, whereas the difference between sectors was more prominent during the post-monsoon season. An increased number of correlations between physical parameters and metal concentration were observed in the post-monsoon season and post-COVID-19 scenario. This study provides evidence that the imposition of COVID-19 lockdown reduced metal influx in the water column and improved the water quality of the Chilika lagoon. Our results can be used as baseline for metal concentration in surface waters of the lagoon.