Although train simulation research is vast, most available network simulators do not track the instantaneous movements and interactions of multiple trains for the computation of energy/fuel consumption. In this paper, we introduce the NeTrainSim simulator for heavy long-haul freight trains on a network of multiple intersecting tracks. Trains are modeled as a series of moving mass points (each car/locomotive is modeled as a point mass) while ensuring safe following distances between them. The simulator considers the motion of the train as a whole and neglects the relative movements between the train cars/locomotives. Furthermore, the powers of the different locomotives are transferred to the first locomotive as such a simplification result in a reduced simulation time without impacting the accuracy of energy consumption estimates. While the different tractive forces are combined, the resistive forces are calculated at their corresponding locations. The output files of the simulator contain pertaining information to the train trajectories and the instantaneous energy consumption levels. A summary file is also provided with the total energy consumed for the full trip and the entire network of trains. Two case studies are conducted to demonstrate the performance of the simulator. The first case study validates the model by comparing the output of NeTrainSim to empirical trajectory data using a basic single-train network. The results confirm that the simulated trajectory is precise enough to estimate the electric energy consumption of the train. The second case study demonstrates the train-following model considering six trains following each other. The results showcase the model’s ability in relation to maintaining safe-following distances between successive trains. Finally, the NeTrainSim is demonstrated to be scalable with computational times of O(n) for less than 50 trains (n) and O(n²) for higher number of trains.

he present experiment concerns deposition of ZnO by ALD and subsequent growth of nanowires by chemical bath. We used a novel AISI 301 steel substrate with mechanical parameters that make it suitable to use as a piezoelectric component in an energy harvesting device. We found out that a thin layer of another oxide below ZnO provides outstanding adhesion. Without it, ZnO exhibits island growth and is mechanically unstable. Such prepared samples were placed under repeated mechanical stress. They showed a piezoelectric signal which is stable after hundreds of actuations. This shows good promise for use of our device based on ZnO, an earth-abundant and non-toxic material, as an alternative to widespread in piezo components but environmentally unfriendly PZT. The piezo layers generated enough power for operations performed by a IoT chip. The designed measurement setup allowed for the demonstration of an application of AISI 301 steel substrate coated with ZnO by atomic layer and chemical bath deposition techniques as a piezoelectric component capable of generating energies usable in Internet of Things applications.

The dark energy from virtual gravitons is consistent with observational data on supernova with the same accuracy as the CDM model. The fact that virtual gravitons are capable of producing of a de Sitter accelerated expansion of the FLRW universe was established in 2008 (see references). The combination of conformal non–invariance with zero rest mass of gravitons (unique properties of the gravitational field) leads to the appearance of graviton dark energy in a mater-dominated era. Тhis fact explains the relatively recent appearance of the dark energy and answers the question “Why now?”. The transition redshifts (where deceleration is replaced by acceleration) that follow from the graviton theory are consistent with model independent transition redshifts derived from observational data. Prospects for testing the GCDM model (the graviton model of dark energy where G stands for gravitons) and comparison with the CDM model are discussed.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

Metabolic flexibility is the ability of an organism to adapt its energy source based on nutrient availability and energy requirements. In humans, this ability has been linked to cardio-metabolic health and healthy aging. Genome-scale metabolic models have been employed to simulate metabolic flexibility by computing the Respiratory Quotient (RQ), which is defined as the ratio of carbon dioxide produced to oxygen consumed, and varies between values of 0.7 for pure fat metabolism and 1.0 for pure carbohydrate metabolism. While the nutritional determinants of metabolic flexibility are known, the role of low energy expenditure and sedentary behavior in the development of metabolic inflexibility is less studied. In this study we present a new description of metabolic flexibility in genome-scale metabolic models which accounts for energy expenditure, and we study the interactions between physical activity and nutrition in a set of patient-derived models of skeletal muscle metabolism in older adults. The simulations show that fuel choice is sensitive to ATP consumption rate in all models tested. The ability to adapt fuel utilization to energy demands is an intrinsic property of the metabolic network

Research Highlights: (1) Reed canary grass (RCG) is analysed in Sweden compared to willow and poplar for 2001-2020 (2) Each crop presents a different land-use and climatic profile (3) Average yield records of reed canary grass are similar to willow and poplar (4) There are divergences between trial-based and commercial yields (5) Existing LUC patterns suggest meadow>RCG and RCG>cereal (6) RCG land area is very sensitive to policy incentives. Background and objectives: RCG is an alternative crop for biomass-to-energy due to high yield and frost tolerance. We assess the cultivation in Sweden by using an extensive compilation of data, with emphasis on the extension of the cultivation, areas planted, climatic profile, land use patterns and yield levels. Material and methods: All RCG plantations are analysed for 2001-2020. A geostatistical analysis is performed to characterize where is cultivated and the land uses associated. Climatic, productivity and yield profiles are compared to willow and poplar plantations, from experiments and from commercial plantations. Results: The results show that the cultivation of reed canary grass expanded after 2005, with a maximum of 800 ha in 2009 to then decrease to the current levels of about 550 ha. It is mainly grown in colder climatic areas, with lower agricultural productivity than willow and poplar. Mean yields from trials are 6 odt ha-1 yr-1; commercial yields are 3.5 odt ha-1 yr-1. RCG replace meadow land and is replaced by cereals, when abandoned. Conclusions: Reed canary grass is an interesting alternative, growing on colder areas but on similar yield levels than other energy crops. The cultivation is more sensitive to policy incentives

Energy demand has been overgrowing in developing countries. Moreover, the fluctuation of fuel prices is a primary concern faced by many countries that highly rely on conventional power generation to meet the load demand. Hence, the need to use alternative resources such as renewable energy is crucial to mitigate fossil fuel dependency alongside the reduction of Carbon Dioxide emission. Algeria’s being the largest county in Africa has rapid growth in energy demand since the past decade due to the significant increase of residential, commercial, and industry sectors. Currently, the hydrocarbon-rich nation highly dependent on fossil fuels for electricity generation, where renewable energy only has a small contribution to the country’s energy mix. However, the country has massive potential for renewable energy generations such as solar, wind, biomass, geothermal, and hydropower. Therefore, the government aims to diversify away from fossil fuel and promoting renewable energy generations through policies and renewable energy-related programs. The country’s Renewable Energy and Energy Efficiency Development Plan focuses on large scale solar, wind generation as well as geothermal and biomass technologies. This paper provides an update on the current energy position and renewable energy status in Algeria. Moreover, this paper discusses RE policies and programs that aim to increase the country’s renewable energy generation and its implementation status.

Stellar heated gas and dust makes a significant entropic/information energy contribution to the universe. At temperatures ~10⁷ the ~10⁸⁶ bits are equivalent to ~10⁷⁰J, equivalent to the energy equivalence of the universe’s ~10⁵³ kg ordinary baryon matter. A survey of stellar mass density measurements shows this dark energy contribution has a constant energy density that effectively mimics a cosmological constant over the redshift range z<1.35. The measurable difference between this information energy and a true cosmological constant is small, with a maximum difference of <2% in Hubble parameter at z~2. As information energy is significant and co-located with hot baryons it produces gravitational effects that resemble dark matter. Information energy is shown to be consistent with the dark matter effects observed in clusters of colliding galaxies (e.g. Bullet Cluster), with dark matter location specified by baryon location and strongest in regions of highest luminosity / temperature. The dark matter fraction measured in galaxy surveys more closely fits an information energy explanation than the fraction expected in the standard ɅCDM model. Information energy provides a solution to the cosmological coincidence problem and also would allow the cosmological constant to take the preferred zero value.

The present article discusses the institutional model adopted in Brazil regarding energy production through biomass. The theoretical-empirical method is used to conclude that the model's difficulties can be overcome by adopting a network of contracts capable of subjecting renewable energy generation to an energy compensation model.

The high consumption of firewood in Honduras requires the search for alternatives that reduce its negative effects on health, economy, and the environment. One of these alternatives has been the promotion of improved cooking stoves, which achieve a large reduction in firewood consumption. This paper shows a cost-benefit analysis for an improved cooking stove adoption strategy for Honduras. The methodology uses the Long-range Energy Alternatives Planning System, LEAP, a tool globally used in the analysis and formulation of energy policies and strategies. The energy model considers the demand for firewood as well as the gradual introduction of improved cooking stoves, according to premises of a National Strategy. Hence, it is demonstrated that the costs of implementing this adoption strategy are lower than the costs of not implementing it, taking into consideration various scenarios up to and including the year 2030.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

The role of energy and entropy in decomposition of turbulent velocity flow-fields is to be shown in the paper. The decomposition methods based on energy concept are taken into account, namely the Proper Orthogonal Decomposition (POD) and its extension Bi-Orthogonal Decomposition (BOD). Entropy motivated view on the decomposed modes could offer new possibilities in the modes physical interpretation and in Reduced Order Modelling (ROM) strategy efficiency evaluation.

This study spatially estimates degraded lands in Indonesia that have limited functions for food production, carbon storage, and conservation of biodiversity and native vegetation, and examines their suitability to grow biodiesel species (Calophyllum inophyllum, Pongamia pinnata and Reutealis trisperma) and biomass species (Calliandra calothyrsus and Gliricidia sepium). Results showed that Indonesia has ∼3.5 million ha of degraded lands potentially suitable for these species. With the all-five-species scenario, these lands had the potential to produce 1105 PJ yr⁻¹ of biomass and 3 PJ yr⁻¹ of biodiesel. With the biodiesel-only-species scenario, these lands showed the potential to produce 10 PJ yr⁻¹ of biodiesel. Despite this energy potential, however, the land sizes were too small to support economies of scale for biofuel production. The study findings contribute to identifying lands with limited functions, modeling biofuel-species growth on regional lands and estimating carbon stocks of restored degraded lands in Indonesia.

Device-to-device (D2D) communication is an essential part of the future fifth generation (5G) system that can be seen as “network of networks”, consisting of multiple seamlessly integrated radio access technologies (RATs). Public safety communications, autonomous driving, social-aware networking, and infotainment services are example use cases of D2D technology. High data rate communications and use of several active air interfaces in the described network create energy consumption challenges for both base stations and the end user devices. In this paper, we review the status of 3GPP standardization and define a set of application scenarios. We use the recent models of 3GPP Long Term Evolution (LTE) and WiFi interfaces in analyzing the power consumption both from the infrastructure and user device perspectives. The results indicate that the number of active interfaces should be minimized.

In this three-part paper, we show that gravitational waves (classical and quantum) produce the accelerated de Sitter expansion at the start and by the end of the cosmological evolution of the Universe. In these periods of time, the Universe contains no matter fields but contains classical and quantum metric fluctuations, i.e. it is filled with classical gravitational waves and gravitons. In such gravitational wave and graviton dominated eras of evolution of the Universe, the de Sitter state is the exact solution to the self-consistent equations for gravitational waves and gravitons and background geometry for the empty (with no matter fields) space-time with FLRW metric. In both classical and quantum cases, this solution is of the instanton origin since it is obtained by Wick rotation with the subsequent analytic continuation to real time. The cosmological acceleration from gravitational waves and gravitons provides a transparent physical explanation to the coincidence and threshold paradoxes of dark energy avoiding recourse to the anthropic principle. The cosmological acceleration from gravitons/gravitational waves at the start of the Universe evolution produces inflation which is consistent with the observational data on CMB anisotropy.

Thermoelectric materials may be used in devices as thermoelectric “air conditioner” in a smart house for improved energy efficiency. Energy harvesting uses ambient energy to generate electricity. It provides potentially low-cost, maintenance-free, long-life equipment by reducing the need for batteries or power chords. Energy harvesting (EH) is also known as power harvesting or energy scavenging. EH is considered to give benefits related to environmental friendliness, safety, security, convenience and affordability. EH can be used for brand enhancing. Technically, it can be used to make new things possible depending on visionary engineering. The variety of thermoelectric (TE) materials that can be used in energy harvesting is quite large, and the optimal material for a given application depends mainly on the temperature range in which the material is to be used. In this work we study the development and characterization of thermoelectric materials which were prepared by two different method, which were: a) ball-milling followed by sintering and b) ball-milling, microwave synthesis, high energy planetary ball milling, and sintering. Finally, we study the thermoelectric properties, calculate the band gaps and the ZT for the thermoelectric materials.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

As the world’s second largest economy, China ranks amount the world’s top nations when it comes to carbon emission, and therefore its attitude towards climate change is closely followed by all parties concerned. There have been few researches on the role of environmental governance in low-carbon city transformation process, especially the Chinese one. This paper analyses the role of government environmental regulation played in the low-carbon city transformation process by taking Shenzhen as the research object. One of the world's youngest super cities, it also happens to be the lowest carbon emission intensity city in China. Striving to explore green low-carbon development path for the whole country, Shenzhen provides practical experience for countries to cope with global climate change. However, its efforts to reduce the total carbon emissions failed, but it emphasized the carbon emission intensity, which is consistent with the international commitments made by the central government. China’s policy towards handling climate change relies on hierarchical governance arrangement. The strength of the NGOs in the country is weak and incomparable with the government’s, which has mastered most of the resources and is just a reality in China.

Quantum machine learning applications have become viable with the recent advancements in quantum computing. Merging ML with the power of quantum computing holds great potential for data-driven decision-making, as well as the development of more powerful models capable of handling more complex datasets with faster processing time. This area offers potential for improving the accuracy of real-time forecasting renewable energy production. However, the literature on this topic is sparse. Addressing this knowledge gap, this study aims to design, implement, and evaluate the performance of a quantum neural network forecast model for solar irradiance up to 3-hours ahead. The proposed model was compared with Support Vector Regression, Group Method of Data Handling, and Extreme Gradient Boost classical models. Using the best quantum neural network configuration found, the proposed framework could provide competitive results when compared to its competitors, considering forecasting intervals of 5- to 120-minutes ahead, where it was the fourth best-performing paradigm. For 3-hours ahead predictions, the QNN was able to overcome its clas-sical counterparts, but the XGBoost. This fact can be an indication that the quantum model may identify and retrieve relevant spatiotemporal information from the input dataset in such a manner not attainable by the current classical approaches.

There is currently an exponential growth in the electric vehicle market, which will require an increase in the electrical grid capacity to meet the demand of charging. If, on the one hand, the introduction of energy generation from renewable sources can be used to meet that requirement, the intermittent nature of some of these sources poses challenges to the required real time equilibrium between generation and consumption. The impossibility of controlling generation from some of these sources leads to the attempt of controlling and manage the consumption of electricity, according with the levels of generation. In this context, the emergence of smart grids has introduced mechanisms that guarantee a balance between consumption and generation of electricity. One of these mechanisms is the smart charging of electric vehicles. Effective smart charging relies on communication between the supply equipment and the electric vehicle, en-abling the adjustment of the energy transfer according with the generation levels. Thus, there is a necessity for a standardised system that guarantees this communication. In this context, the ISO 15118 standard, allows high level communication mechanisms, much beyond the basic control solutions offered by the IEC 61851-1 specification. In this context, this paper presents the development of a charge emulation system, based on the ISO 15118 communication protocol and discusses its application for demand response purposes.

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

Wind turbine upgrades have been spreading in the recent years in the wind energy industry, with the aim of optimizing the efficiency of wind kinetic energy conversion. This kind of interventions has material and labor costs and it is therefore fundamental to estimate realistically the production improvement. Further, the retrofitting of wind turbines sited in harsh environments might exacerbate the stressing conditions to which wind turbines are subjected and consequently might affect the residue lifetime. This work deals with a case of retrofitting: the testing ground is a multi-megawatt wind turbine from a wind farm sited in a very complex terrain. The blades have been optimized by installing vortex generators and passive flow control devices. The complexity of this test case, dictated by the environment and by the features of the data set at disposal, inspires the formulation of a general method for estimating production upgrades, based on multivariate linear modeling of the power output of the upgraded wind turbine. The method is a distinctive part of the outcome of this work because it is generalizable to the study of whatever wind turbine upgrade and it is adaptable to the features of the data sets at disposal. In particular, applying this model to the test case of interest, it arises that the upgrade increases the annual energy production of the wind turbine of an amount of the order of the 2%. This quantity is of the same order of magnitude, albeit non-negligibly lower, than the estimate based on the assumption of ideal wind conditions. Therefore, it arises that complex wind conditions might affect the efficiency of wind turbine upgrades and it is therefore important to estimate their impact using data from wind turbines operating in the real environment of interest.

The rapid progress in renewable energy sources and the increasing complexity of energy distribution networks have highlighted the need for efficient and intelligent energy management systems. This paper presents a comparative analysis of two optimisation algorithms, P and M70, used for the optimal control of the operation of microgrids in islanded mode. The main objective is to minimise production costs while ensuring a reliable energy supply. Algorithm P prioritises the use of photovoltaic (PV) and battery storage and operates the diesel generator at minimum capacity to reduce fuel consumption and maximise the use of renewable energy sources. Algorithm M70, on the other hand, uses a heuristic approach to adaptively manage energy resources in real time. In this study, the performance of both algorithms is evaluated through simulation in different operating scenarios. The results show that both algorithms significantly improve the efficiency of the microgrid, with the M70 algorithm showing better adaptability and cost efficiency in dynamic environments. This research contributes to ongoing efforts to develop robust and scalable energy management systems for future smart grids.

This review paper addresses the growing challenges and developments in frequency control within power systems influenced by increasing penetration of renewable energy sources. It evaluates the advancements and limitations of renewable-based control technologies and explores the critical role of diverse energy storage technologies in providing fast frequency response ancillary services. Through a comprehensive analysis of global literature, this paper categorizes energy storage solutions according to their efficacy in meeting fast frequency response demands and potential for revenue generation. It reveals significant gaps in current research, which predominantly focuses on battery energy storage systems and microgrid applications, with insufficient attention to grid-scale storage solutions and innovative energy storage technologies. This analysis identifies a lack of detailed technical simulations and hybrid storage models for frequency control, as well as a minimal exploration of the environmental benefits, particularly in terms of carbon dioxide emission reductions, associated with deploying new energy storage technologies in ancillary service markets. The paper concludes by highlighting the necessity for further research incorporating detailed techno-economic evaluations and carbon dioxide reduction potential of modular, scalable energy storage technologies, facilitated by advanced network simulation models and comprehensive market analysis.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Although solar photovoltaic (PV) system costs have declined, capital cost remains a barrier to widespread adoption. Do-it-yourself (DIY) system designs can decrease costs by about 50% by reducing labor costs, but if not attached to a building structure demand ground penetration for conventional footings. This is not technically and economically feasible at all sites. To overcome these challenges, this study details systems designed to eliminate drilling holes and pouring concrete. Two different designs for both fixed tilt and variable tilt PV racking are investigated to assess their structural integrity, constructability, and economic cost when fabricated with a ballast-supported foundation. The ballast-supported foundations are analyzed for eight such systems by proposing two separate ballast designs: one for single line of post systems, and one for double line of post systems built on a 4-kW basis. The results of the analysis found that both designs are slightly more expensive than typical in-ground concrete systems by 25%, but the overall DIY systems costs remain economically advantageous. Sensitivity analyses are conducted to show how modifications to the dimensions including clearances and distances between gabions influence the weight of the system and thus change the economic value of the design, so users can trade dimensional freedom for cost-savings, and vice versa. Overall, all the wood-based PV racking system designs provide users with cost-effective and easy DIY alternatives to conventional metal racking, and the novel ballast systems presented provide more versatility for PV systems installations.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

In recent years, advancements in rooftop solar panel technology have sparked a revolution in the electricity markets. This has given rise to a new concept of energy exchange - the ability for consumers and producers to trade localized energy. This concept has been made possible by the emergence of blockchain technology, which has gained significant traction in the energy markets. Its unique ability to facilitate peer-to-peer (P2P) energy transactions has made it a promising solution for the trilemma of scalability, security, and decentralization. However, while blockchain technology has shown great potential, it is still in its early stages of development and has yet to reach its full potential. To fully understand the potential of blockchain technology in P2P energy trading, it is important to explore the trilemma in depth. This study proposes a blockchain-based scalability solution, with a focus on P2P energy trade. This strategy is supported by empirical modeling, utilizing data gathered from a trial case study. The results of this study demonstrate that the suggested technique outperforms base layer models in terms of scalability, while still maintaining the essential elements of security and decentralization. This proposed solution not only has the potential to revolutionize the energy markets, but also has broader implications. By providing a more secure and decentralized platform for P2P energy trading, it has the potential to address issues of energy distribution inequality and promote the adoption of renewable energy. With blockchain technology, individuals and communities have the opportunity to take control of their energy usage and production, reducing their reliance on traditional centralized energy systems. This not only has the potential to lower energy costs for consumers, but also contributes to the overall goal of reducing carbon emissions and mitigating the effects of climate change. The combination of rooftop solar panel technology and blockchain applications has the potential to create a significant shift towards decentralized and sustainable energy systems. This will not only benefit individuals and communities, but also have a positive impact on the environment and the global energy market as a whole. However, for this transition to occur, it is crucial that governments and energy companies continue to support and invest in these advancements.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

The ubiquitous connectivity for the space-air-ground integrated network (SAGIN) of the beyond fifth generation of communication and sixth generation of communication (B5G/6G) is envisaged to meet the needs for the demanded quality of service (QoS), green communication, and "dual carbon" target. However, the offloading and computation of massive latency-sensitive tasks dramatically increases the energy consumption of the network. Furthermore, the traditional power supply technology of the network base stations (BSs) enhances the carbon emission. To address these issues, we first propose a SAGIN architecture with energy harvesting devices, where the BS is powered by both renewable energy (RE) and the conventional grid. The BS explores wireless power transfer (WPT) technology to power the unmanned aerial vehicle (UAV) for stable network operation. RE sharing between neighbouring BSs is designed to fully utilize RE for reduce carbon emission. Secondly, on the basis of task offloading decision, UAV trajectory, and RE sharing ratio, we construct cost functions with joint latency-oriented, energy consumption, and carbon emission. Then, we develop a twin delayed deep deterministic policy gradient (TD3PG) algorithm based on deep reinforcement learning to minimize the cost function. Finally, simulation results demonstrate that the proposed algorithm outperforms the benchmark algorithm in terms of reducing latency, energy saving, and lower carbon emission.

In recent years, the need to make the built environment more resilient and adaptable to climate change has become increasingly evident. In Europe, this aspect concerns the vast majority of existing buildings, which present several deficiencies from the energy-efficiency point of view, considering they were designed before the introduction of modern energy codes. Nowadays, it is possible to retrofit existing buildings using advanced and high-efficient technologies such as Double Skin Façades (DSFs). The research aims to evaluate the use of properly designed DSFs for the energy restoration of existing buildings. In detail, various DSF configurations are applied to a residential building located in central Italy and investigated under present and future climate conditions, estimated through regional climate models. The results underline that all the analysed Double Skin Façades confirm to be a useful option, and, in particular, the Multi-Storey typology allows drastic energy needs decrement. Moreover, the general increase in temperatures and solar radiations could affect the building energy performance, and the insertion of DSF can mitigate the climate change effects, reducing the predicted energy consumption and ensuring better behaviours than the building in its original state.

RNA viruses exhibit a great tendency to mutate. Starting from 2019, the wild type that was labeled Hu-1 has during the last 3 years evolved to produce several dozen new variants, as a consequence of mutations. Mutations cause changes in empirical formulas of new virus strains, which lead to change in thermodynamic properties of biosynthesis and binding. These changes cause changes in the rate of reactions of binding of virus antigen to the host cell receptor and the rate of virus multiplication in the host cell. Changes in thermodynamic and kinetic parameters lead to changes in biological parameters of infectivity and pathogenicity. SARS-CoV-2 has starting from in 2019, until today, evolved towards increase in infectivity and maintaining constant pathogenicity, or for some variants a slight decrease in pathogenicity. In the case of Omicron BQ.1, BQ.1.1, XBB and XBB.1 variants pathogenicity is identical as in the Omicron BA.2.75 variant. On the other hand, infectivity of the Omicron BQ.1, BQ.1.1, XBB and XBB.1 variants is greater than those of previous variants. This will most likely result in the phenomenon of asymmetric coinfection, that is circulation of several variants in the population, some being dominant.

The energy sector plays an important role in Mexico’s development trajectory. Mexico makes an interesting case study, because it shows how difficult it is to reduce fossil energy dependence despite geographic and climatic conditions that favour renewable energy deployment and use. Resolving path dependencies and the related carbon lock-in are key to Mexico’s sustainable energy transition. This case study aims to identify and discuss how carbon lock-in affects Mexico’s sustainable energy transition. Mexico’s carbon lock-in involves oil and oil-run power plants that are costly to build but relatively inexpensive to operate. This case study identifies potential entry points for transitioning towards sustainable energy in Mexico – resources that can promote the use of clean energy despite carbon lock-in. For example, focusing on electrification – particularly of the carbon-intensive sectors – can help Mexico transit towards sustainable energy despite institutional constraints. Complementing this case study is a teaching guide with recommendations for using Mexico’s energy transition in courses on sustainability. It introduces a “learning activation framework” to identify emerging opportunities that can advance sustainable energy transitions in different cases of carbon lock-in. Finally, the framework also gives students a chance to help dismantle or cope with carbon lock-ins.

We study the center of energy (CE) before and after the separation of superposed wave from a moving medium (MM). It is assumed that two out-of-phase mechanical transverse waves propagating from the opposite directions on a medium moving at non-relativistic speeds are superposed and the superposed portion (SP) is separated from the MM at that moment. We consider the CE of the SP before and after the separation from the MM. The location of CE (LCE) of the SP seems to be at the center of it at the moment of superposition. The SP rotates due to the separation from the MM since the velocity of each portion symmetric with respect to the center of the SP is equal in magnitude and opposite in direction. The magnitudes of velocities of the symmetric portions become different as soon as the SP begins to rotate with the separation from the MM. Then the energies of their symmetric portions are not the same, so the LCE of the SP is not at the center of it. As a result, the LCE of it looks different before and after the separation from the MM. We must find a solution to keep the LCE of the SP constant. We propose that two out-of-phase mechanical transverse waves (MTWs) propagating from the opposite directions on a MM originally have hidden difference in relativistic energy and it suddenly appears within the range observable in Newtonian mechanics when the SP starts rotating. This means that the point of view of hidden difference in relativistic energy is necessary to keep the LCE constant.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

Real-time energy management of a converter-based microgrid is difficult to determine optimal operating points of a storage system in order to save costs and minimise energy waste. This complexity arises due to time-varying electricity prices, stochastic energy sources and power demand. Many countries have imposed real-time electricity pricing to efficiently control demand side management. This paper presents a particle swarm optimisation (PSO) for the application of real-time energy management to find optimal battery controls of a community microgrid. The modification of the PSO consists in altering the cost function to better model the battery charging/discharging operations. As optimal control is performed by formulating a cost function, it is suitably analysed and then a dynamic penalty function in order to obtain the best cost function is proposed. Several case studies with different scenarios are conducted to determine the effectiveness of the proposed cost function. The proposed cost function can reduce operational cost by 12% as compared to the original cost function over a time horizon of 96 hours. Simulation results reveal the suitability of applying the regularised PSO algorithm with the proposed cost function, which can be adjusted according to the need of the community, for real-time energy management.

Cogging torque is a pulsating, parasitic and undesired torque ripple intrinsic of the design of a permanent magnet synchronous generator (PMSG), which should be minimized due to its adverse effects: vibration and noise. In addition, as aerodynamic power is low during start-up at low wind speeds in small wind energy systems, the cogging torque must be as low as possible to achieve a low cut-in speed. A novel mitigation technique using compound pre-slotting, based on a combination of magnetic and non-magnetic materials, is investigated. The finite element technique is used to calculate the cogging torque of a real PMSG design for a small wind turbine, with and without using compound pre-slotting. The results show that cogging torque can be reduced by a factor of 48% with this technique, while avoiding the main drawback of the conventional pre-slotting technique: the reduction of induced voltage due to leakage flux between stator teeth. Furthermore, through a combination of pre-slotting and other cogging torque optimization techniques, 84%, cogging torque can be eliminated for a given design.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Matter grows and self-assembles to produce complex structures such as virus capsids, carbon fullerenes, proteins, glasses, etc. Due to its complexity, performing pen-and-paper calculations to explain and describe such assemblies is cumbersome. Many years ago, Richard Kerner presented a pen-and-paper path integral approach to understand self-organized matter. Although successfully addressed many important problems including the yield of fullerene formation, the glass transition temperature of doped chalcogenide glasses, the fraction of boroxol rings in B2O3 glasses, the first theoretical explanation for the empirical recipe of window and Pyrex glass and the understanding of virus capsid self-assembly, still is not the primary choice when tackling similar problems. The reason lies in the fact that it diverges from mainstream approaches based on the energy landscape paradigm and non-equilibrium thermodynamics. In this context, a critical review is presented, demonstrating that the Richard Kerner method is, in fact, a clever way to identify relevant configurations. Its equations are simplified, common physical sense versions to those found in the energy landscape kinetic equations. Subsequently, the utilization of equilibrium Boltzmann factors in the transition Markov chain probabilities is analyzed within the context of local two-level energy landscape models kinetics. This analysis demonstrates that their use remains valid when the local energy barrier between reaction coordinate states is small compared to the thermal energy. This finding places the Richard Kerner model on par with other more sophisticated methods and, hopefully, will promote its adoption as an initial and useful choice for describing the self-agglomeration of matter.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

We reduplicate the Book “Dark Energy” by M. Li, X-D. Li, and Y. Wang, given zero-point energy calculation with an unexpected “length’ added to the ‘width’ of a graviton wave just prior to specifying the creation of ‘gravitons’, using the Rosen and Israelit model of a nonsingular universe. In doing so we are in addition to obtaining a wavelength 10^30 times greater than Planck’s length so we can calculate DE, may be able to with the help of the Rosen and Israelit model have a first approximation as to the arrow of time, and a universe with massive gravity. We have left the particulars of the nonsingular starting point undefined but state that the Rosen and Israelit model postulates initial temperatures of 10^-180 Kelvin and also a value of about Planck temperature, at 10^-3 centimeters radii value which may satisfy initial conditions asked by t’Hooft for describing an arrow of time. A key assumption is that the DE is formed at 10^-3 cm, after an expansion of 10^30 times in radii, from the Planck length radius nonsingular starting point. The given starting point for DE in this set of assumptions is where there is a change in the cosmic acceleration, to a zero value, according to Rosen and Israel, with time t = 1.31 times 10^-42 seconds. Which may be where we may specify a potential magnitude, V, which has ties into inflaton physics. The particulars of the model from Rosen and Israelit allow a solution to be found, without discussion of where that nonsingular starting point came from, a point the author found in need of drastic remedies and fixes.

: This study presents energy and exergy analyses conducted on a Gifford-McMahon cycle refriger-ator. Through detailed numerical simulations, the performance of the refrigerator is thoroughly assessed, with a particular focus on energy and exergy losses. The obtained results are compared with Sankey and Grassman diagrams, providing visual representations of energy and exergy flows within the system. The localization of exergy losses is carefully analysed to identify key areas for optimization aimed at enhancing efficiency and power output. By pinpointing sources of ex-ergy destruction, targeted improvements can be implemented to maximize the overall perfor-mance of the refrigerator. Overall, this research contributes to a deeper understanding of the thermodynamic behaviour of Gifford-McMahon cycle refrigerators and provides valuable insights for optimizing their performance in practical applications.

Intracellular potassium concentrations, [K+], are high in all types of living cells, but the origins of this K+ are unknown. The simplest hypothesis is that life emerged in an environment that was high in K+. One such environment is the spaces between the sheets of the clay mineral, mica. The best mica for life’s origins is the black mica, biotite, because it has a high content of Mg++ and it has iron in various oxidation states. Life also has many of the characteristics of the environment between mica sheets, giving further support for the possibility that mica was the substrate on and within which life emerged.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

There are two major proposed forms of dark energy: the cosmological constant and the quintessence scalar field. However, the former has the cosmological constant problem and the latter does not have observational evidence to support the theory. In this paper, we propose a dark energy paradigm to solve the cosmological constant problem and to predict lepton masses as evidence. The dark energy paradigm is a unified dark sector that is based on Planck's dimensional analysis, Lambda CDM, energy conservation, and force equilibrium. We find that dark energy can vary from the cosmological constant to the Planck scale. We find that the predicted values of lepton masses based on the dark energy paradigm agree with the observed values to 1% (or within error ranges).

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

In this paper, a systematic literature review is presented, through a survey in the main digital databases, about modelling methods for Short-Term Load Forecasting (STLF) for hourly electricity demand for residential electricity and to realize the performance evolution and impact of the Artificial Intelligent (AI) in STLF. With these specific objectives, it was developed a conceptual framework on the subject, a systematic review of the literature based on scientific publications with high impact and a bibliometric study directed to the scientific production of AI and STLF. The review of research articles over a 10-year period, which takes place between 2012-2022, uses the Preferred Reporting Items for Systematic and Meta-Analyses (PRISMA) method. This research resulted in more than 300 articles, available in 4 (four) databases: Web of Science, IEEE Xplore, Scopus and Science Direct. The research was organized around 3 (three) central themes, which were defined through keywords: STLF, Electricity, Residential and their corresponding synonyms. 334 research articles were analyzed and identified the year of publication, journal, author, geography by continent and country and the area of application. Of the 334 documents found in the initial research and after applying the inclusion/exclusion criteria, which allowed delimiting the subject addressed in the topics of interest for analysis, 37 (thirty-seven) documents are in English (25 are journal articles and 12 are conference papers). The results point to a diversity of modelling techniques and associated algorithms. The corresponding performance is measured with different metrics and, therefore, cannot be compared directly. Hence, it should be desirable to have a unified data set together with a set of benchmarks with well-defined metrics for a clear comparison of all the modelling techniques and the corresponding algorithms.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

For more than one hundred years, scientists dispute the correct interpretation of Lorentz transformations within the framework of the special theory of relativity of Albert Einstein. On the one hand, the changes in length, time and mass with increasing velocity are interpreted as apparent due to the observer dependence within special relativity. On the other hand, real changes are described corresponding to the experimental evidence of mass increase in particle accelerators or of clock delay. This ambiguity is accompanied by an ongoing controversy about valid Lorentz-transformed thermodynamic quantities such as entropy, pressure and temperature. In this paper is shown that the interpretation problem of the Lorentz transformations is genuinely anchored within the postulates of special relativity and can be solved on the basis of the thermodynamic approach of matter-energy equivalence, i.e. an energetic distinction between matter and mass. It is suggested that the velocity-dependent changes in state quantities are real in each case, in full agreement with the experimental evidence.

Ethical sourcing practices play a pivotal role in addressing price inflation within renewable energy supply chains. This qualitative research investigates the multifaceted impacts of ethical sourcing, drawing insights from interviews with key stakeholders in the renewable energy sector. The study reveals that ethical sourcing enhances supply chain transparency, traceability, and resilience by mitigating risks associated with unethical practices such as labor exploitation and environmental degradation. Fair trade initiatives contribute to economic stability and reduce price volatility by ensuring fair compensation for producers and workers, fostering long-term relationships, and reinvesting premiums into community development projects. Sustainable sourcing practices align with consumer preferences for eco-friendly products, reduce the demand for virgin resources, and promote regulatory compliance and incentives, thereby stabilizing costs and reducing environmental impact. Socially responsible companies that prioritize fair labor practices and community support experience fewer disruptions and benefit from a more stable and productive workforce. Entrepreneurship and emotional intelligence among leaders drive the adoption and successful implementation of ethical sourcing practices, enhancing brand reputation, consumer trust, and market competitiveness. Despite challenges, such as higher implementation costs and supplier resistance, the long-term benefits of ethical sourcing outweigh the initial costs and contribute to sustainable supply chains. Collaboration, consumer education, and effective regulation are essential for promoting ethical sourcing across the renewable energy sector.

Background and Objective: Segmentation of the femur in Dual Energy X-ray (DXA) images poses challenges due to reduced contrast, noise, bone shape variations, and inconsistent X-ray beam penetration. In this study, we investigate the relationship between noise and certain deep learning (DL) techniques for semantic segmentation of the femur to enhance segmentation and bone mineral density (BMD) accuracy by incorporating noise reduction methods into DL models. Methods: Convolutional neural network (CNN) based models were employed to segment femurs in DXA images and evaluate the effects of noise reduction filters on segmentation accuracy and its effect on BMD calculation. Various noise reduction techniques were integrated into DL-based models to enhance image quality before training. We assessed the performance of the fully convolutional neural network (FCNN) in comparison to noise reduction algorithms and manual segmentation methods. Results: Our study demonstrated that FCNN outperformed noise reduction algorithms in enhancing segmentation accuracy and enabling precise calculation of BMD. The FCNN-based segmentation approach achieved a segmentation accuracy of 98.84% and a correlation coefficient of 0.9928 for BMD measurements, indicating its effectiveness in the clinical diagnosis of osteoporosis. Conclusions: In conclusion, integrating noise reduction techniques into DL-based models significantly improves femur segmentation accuracy in DXA images. The FCNN model, in particular, shows promising results in enhancing BMD calculation and clinical diagnosis of osteoporosis. These findings highlight the potential of DL techniques in addressing segmentation challenges and improving diagnostic accuracy in medical imaging.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

From the perspective of manufacturing companies, the political, media and economic discourse on decarbonisation of the recent years manifests itself as an increasing social expectation of action. In Germany in particular, this discourse is also being driven forward by powerful companies, respectively sectors, most notably the automotive industry. Against this background, it was examined how German manufacturing companies react to rising societal pressure and emerging policies. It is examined which measures the companies have taken or plan to take to reduce their footprint, which aspirations are associated with this and by which structural characteristics (company size, energy intensity, sector) these are influenced. A mix methods approach was applied, utilising data gathered from approx. 900 companies in context of the Energy Efficiency Index of German Industry (EEI), along with media research focusing on decarbonisation plans and initiatives announced. We demonstrate that one-size-serves-all approaches are not suitable to decarbonise industry as the situation and ambitions differ considerably depending on size, energy intensity and sector. Even though the level of ambition and urgency is high, particularly micro and energy intensive companies are challenged. The research uncovers a series of questions that call for attention to materialise the ambitions and address the challenges outlined.

Creep deformation behaviour in single phase γ-TiAl alloy has been an extensively studied topic since the late 1970s. A lot of literatures have reported creep behaviour of γ-TiAl alloys, manufactured using different processing techniques [1]–[7]. The present discussion revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase γ-TiAl alloy by Hayes et al. [8] and is aimed to develop an understanding of steady state creep, through strain vs strain rate and strain vs ln(strain rate) plots. Besides, it also attempts to study the variation of stress exponent with temperature between 760-900⁰C and also, to determine activation energies using the two most common approaches, namely: Zener-Hollomon (Z-H) [9] and Sherby-Dorn (S-D, temperature compensated time approach) [10] for stress levels of 69 and 103.4 MPa between 760-900⁰C.

Widely used estimates of food-insecure populations are likely to be biased upwards, lacking adjustment for global increases in sedentary behavior in recent decades. We first construct a household model to account for sedentary choices during leisure and work time decisions. The model rationalizes increasing sedentary behavior from the household by accounting for increasing returns to cognitive human capital vs physical capital, alongside increased productivity of more sedentary activities both at work and at home. The household model then informs an empirical model that makes use of our unique international pseudo-panel data on sitting time, which serves as a proxy for sedentarism. We econometrically estimate a transfer function linking sedentarism to widely available covariates, which then are used to make out-of-sample predictions and can be applied to a large set of countries. The estimated sedentary time can be used to adjust the physical activity level reflected in the minimum dietary energy requirement used to determine a cutoff for food insecurity.

We present a summary of the main results within the Scale Invariant Vacuum (SIV) paradigm as related to the Weyl Integrable Geometry. After a brief review of the mathematical framework, we will highlight the main results related to inflation within the SIV [9], the growth of the density fluctuations [8], and the application of the SIV to scale-invariant dynamics of Galaxies, MOND, Dark Matter, and the Dwarf Spheroidals [7]. The connection of the weak-field SIV results to the un-proper time parametrization within the reparametrization paradigm is also discussed [14].

The ΛCDM model successfully models the expansion of matter in the universe with an expansion of the underlying metric. However, it does not address the physical origin of the big bang and dark energy. A model of cosmology is proposed, where the state of high energy density of the big bang is created by the collapse of an antineutrino star that has exceeded its Chandrasekhar limit. To allow the first neutrino stars and antineutrino stars to form naturally from an initial quantum vacuum state, it helps to assume that antimatter has negative gravitational mass. While it may prove incorrect, this assumption may also help identify dark energy. The degenerate remnant of an antineutrino star can today have an average mass density that is similar to the dark energy density of the ΛCDM model. When in hydrostatic equilibrium, this antineutrino star remnant can emit isothermal cosmic microwave background radiation and accelerate matter radially. This model and the ΛCDM model are in similar quantitative agreement with supernova distance measurements. Other observational tests of the above model are also discussed.

This study aims to provide empirical evidence on whether using renewable and non-renewable energy, CO₂ emissions and the resulting changes in temperature and precipitation can alter cereal yields in European Union countries. To this end, a panel data set covering 1992-2021 has been used to analyse the impact of climate change and economic factors on cereal production in European Union countries. The study employed various analytical techniques to understand better the relationship between climate change, energy consumption, and economic growth. These included using annual average temperature and rainfall to measure climate change and energy consumption and economic growth to analyse the economic aspects. To achieve the objective, feasible generalised least squares (FGLS) models with robust standard errors and bootstrap and a quantile regression (QR) model with marginal analysis were employed. The Westerlund cointegration test confirmed the presence of cointegration between cereal production and climate variables, economic growth, and energy consumption. The results indicate that increases in temperature and precipitation may contribute to increased cereal production in European Union countries. In contrast, energy consumption, including renewable energy and CO₂ emissions, may have a nonlinear effect on cereal production. Quantile regression analysis suggests climate change may impact crop yields most in countries with low and moderate cereal production per hectare. Increased CO₂ emissions may increase yields in the initial period, but excessive CO₂ may negatively impact cereal production in the long term. It would be advisable for countries with low and moderate crop productivity to consider implementing technological advances and combating global warming by modernising cultivation methods and making greater use of renewable energy sources.

Abstract: The increased penetration of renewables in distribution power systems has motivated researchers to take significant interest in local energy transactions. The major goal of Local Energy Markets (LEM) is to promote the participation of small consumers in energy transactions and providing an opportunity for transactive energy systems. Such energy transactions in LEM are considered as a bi-level optimization problem in which all agents at upper and lower levels try to maximize their profits. But typical bi-level problem is very complex as it is inherently nonlinear, discontinued and strongly NP-hard. So, this article proposes the application of hybridized Cross Entropy Covariance Matrix Adaptation Evolution Strategy (CE-CMAES) to tackle such a complex bi-level problem of LEM. The proposed CE-CMAES secured the 1st rank in Testbed-2 entitled, “Bi-level optimization of end-users’ bidding strategies in local energy markets (LM)” at international competitions on Smart Grid Problems, held at GECCO 2020 and WCCI 2020. CE method is used for global exploration of search space and CMAES is used for local exploitation as its adaptive step-size mechanism prevents its premature convergence. A practical distribution system with renewable energy penetration is considered for simulation. The comparative analysis shows that the overall cost, mean fitness and Ranking Index (R.I) obtained from CE-CMAES are superior to those obtained from the state-of-the-art participated algorithms. Wilcoxon Signed Rank Statistical test also proves that CE-CMAES is statistically different from the tested algorithms.

We present a modified version of the Szilard Engine, demonstrating that an explicit measurement procedure is entirely unnecessary for its operation. By considering our modified engine, we are able to provide a new interpretation of Landauer’s original argument for the cost of erasure. From this view, we demonstrate that a reset operation is strictly impossible in a dynamical system with only conservative forces. Then, we prove that to approach a reset yields an unavoidable instability at the reset point. Finally, we present an original proof of Landauer’s principle that is completely independent from the Second Law of Thermodynamics.

HU is the Hypergeometrical Universe Theory (HU)[1-8], proposed in 2006, where the Universe is a Lightspeed Expanding Hyperspherical Hypersurface and Gravitation is an absolute-velocity-dependent, epoch-dependent force. Here we introduce the Big Pop Cosmogenesis and show our calculations associated with the Equation of State of the Universe. This article is the first in a series of articles[9-22] supporting the paradigm shift.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

The application of warm-mixing technology brings considerable economical and environment benefits by decreasing the mixing temperature during warm asphalt mixture(WMA) production. However, the possible water residue also generates concerns in moisture susceptibility. For deep investigation on the influencing factors and mechanism of the moisture susceptibility of WMA, surface free energy(SFE) test and laboratory tests are applied in this research. A novel indicator based on SFE namely effective adhesion work is proposed to assess the asphalt-aggregate adhesion with different moisture contents. Then, given the mixing procedure of dry mixing method, an advanced three-phase model as form of asphalt-aggregate-warm mixing additive is introduced improving from the conventional two-phase asphalt-aggregate model for better reflecting the separate addition of warm mixing additive during mixing. Afterwards, the influence of aggregate types, asphalt type, aggregate moisture contents, warm-mixing agent types and warm-mixing process on the moisture susceptibility of WMA is analyzed utilizing the models and indicators proposed. Finally, the validity of the SFE indicator is verified by comparing the calculation of effective adhesion work with freeze-thaw splitting test result. The results show that all of the above factors impact the moisture susceptibility of WMA by influencing the interfacial adhesion, with the effect of moisture content being the most significant. Meanwhile, effective adhesion work and the three-phase model brought out in this research are proven to be feasible to characterize the adhesion properties of WMA, offering theoretical support to the research on warm mixing technology.

In the context of the minimally extended varying speed of light (meVSL) model, both the absolute magnitude and the luminosity distance of type Ia supernovae (SNe Ia) differ from those predicted by general relativity (GR). Utilizing the Pantheon+ data, we examine the plausibility of various dark energy models under meVSL. Both ωCDM and CPL parameterization dark energy (DE) models exhibit indications of cosmic variations in the speed of light at the 1-σ level. For Ωm0=0.30,0.31, and 0.32 with (ω0,ωa)=(−1,0), the 1-σ range of c˜˙0/c˜0(10−13yr−1) is (-8.76 , -0.89), (-11.8 , 3.93), and (-14.8 , -6.98), respectively. Meanwhile, the 1-σ range of c˜˙0/c˜0(10−12yr−1) for CPL dark energy models with −1.05≤ω0≤−0.95 and 0.28≤Ωm0≤0.32, is (-6.31 , -2.98). The value of c˜ at z=3 can exceed that of the present by 0.2∼3 % for ωCDM models and 5∼13 % for CPL models. Additionally, for viable models except for the CPL model with Ωm0=0.28, we find −25.6≤G˜˙0/G˜0(10−12yr−1)≤−0.36. For this particular model, we obtain an increasing rate of the gravitational constant within the range 1.65≤G˜˙0/G˜0(10−12yr−1)≤3.79.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

Agriculture uses a lot of fuel, fertilizers, pesticides and other substances, while emitting large amounts of GHGs. It is important to optimize these inputs and outputs. One such way is increas-ing crop biodiversity. For this reason, single crops and mixtures of maize, hemp and faba bean as binary and ternary crops were investigated at the Experimental Station of Vytautas Magnus Uni-versity, Lithuania. Results showed that consumption of diesel fuel was by the 31-46% higher than in single and 22-35% higher than in binary cultivations was found in a ternary crop. This influenced on the highest energy input or near twice higher than in maize and hemp single crops and maize+hemp binary crop, but similar with binary crops with faba bean. Despite this, the productivity of the trinary crop and, at the same time, the energy output were 2-5 times higher than in other treat-ments. This compensated for higher energy inputs and the energy efficiency ratio. In ternary crop, energy productivity was from 1.1 to 2.8 times higher and net energy was by 1.9-5.3 times higher than in other tested cultivations. The highest total GHG emissions were obtained in binary maize+hemp and maize+faba bean cultivations (1729.84 and 2067.33 CO2eq ha-1). Ternary cultiva-tion with the highest energy inputs initiated average GHG emission - 1541.90 kg ha-1 CO2eq. For higher efficiency, ternary crop could be sown and harvested in one machine pass. Faba beans should be included in the ter-nary crops, as their biomass takes a significant part of the total biomass produced. We recommend to review the inter-cropped faba bean seeding rates as faba bean seeds have a high energy input equivalent.

Syntrophic acetate oxidation operates close to the thermodynamic equilibrium and very little is known about the participating organisms and their metabolism. Clostridium ultunense is one of the most abundant syntrophic acetate-oxidising bacteria (SAOB) found in engineered biogas processes operating with high ammonia concentrations. It has been proven to oxidise acetate in cooperation with hydrogenotrophic methanogens. There is evidence that the Wood-Ljungdahl (WL) pathway plays an important role in acetate oxidation. In this study we analysed the physiological and metabolic capacities of C. ultunense on genome scale and conducted a comparative study of all known characterised SAOB, namely Syntrophaceticus schinkii, Thermacetogenium phaeum, Tepidanaerobacter acetatoxydans and Pseudothermotoga lettingae. The results clearly indicated physiological robustness beneficial for anaerobic digestion environments and revealed unexpected metabolic diversity with respect to acetate oxidation and energy conservation systems., Unlike S. schinkii and Th. phaeum, C. ultunense clearly does not employ the oxidative WL pathway for acetate oxidation, as its genome (and that of P. lettingae) lack important key genes. In both those species, a proton motive force is likely formed by chemical protons involving putative electron-bifurcating [Fe-Fe] hydrogenases rather than proton pumps. No genes encoding a respiratory Ech hydrogenase, as involved in energy conservation in Th. phaeum and S. schinkii, were identified in C. ultunense and P. lettingae. Moreover, two respiratory complexes sharing similarities to the proton-translocating ferredoxin:NAD⁺ oxidoreductase (Rnf) and the Na+ pumping NADH:quinone hydrogenase (NQR) were predicted. These might form a respiratory chain involved in reduction of electron acceptors other than protons. However, involvement of these complexes in acetate oxidation in C. ultunense and P. lettingae needs further study. This genome-based comparison provides a solid platform for future meta-proteomics and meta-transcriptomics studies and for metabolic engineering, control and monitoring of SAOB.

We do this research to investigate the relationship between renewable energy, public health expenditure, logistics performance indices, and economic and environmental sustainability in the ASEAN member states, through the analysis of a panel data from 2007 to 2017. The study used secondary data, which is downloaded from the World Bank Website and employs SEM (Structural Equation Modelling) model for testing hypothesis. The results show that the usage of renewable energy in logistical operations would enhance the environmental and economic performance in terms of mitigating carbon emissions and greenhouse gas emissions. While, public health expenditure and environmental performance is negatively correlated, which confirms that greater environmental sustainability with lower carbon emissions and greenhouse gases will improve human health and economic growth. Moreover, greater public health expenditure and poor environmental performance has negative effect on economic growth, inefficiency and low productivity of labor slowdown to the economic activities. For another side, the usage of renewable energy and the adoption of green practices in international logistics will develop the environmental sustainability, establish better image of a country and attract foreign direct investment inflows, and also minimize carbon emissions and public health expenditure, spurring sustainable economic growth with better export opportunities in pro-environmental countries.

Hydroxyapatite (HAP) is the main mineral component of bones and teeth. It is widely used in medicine as a bone filler and coating for implants to promote new bone growth. Ion substitutions into the HAP structure highly affect its properties. One of the important substituents is manganese. This paper presents the new results obtained by high-precision density functional theory calculations using hybrid functionals, for studies of the Mn/Ca substitutions in HAP in a wide manganese concentration range within 2x2x2 supercell model. The experimental data on the mechanochemical synthesis of HAP-Mn samples with different Mn concentrations are also presented. The comparison between experiment and theory showed good agreement: the HAP-Mg unit cell parameters and volume decrease with increasing degree of Mn/Ca substitution. It is shown that electronic energy levels appear inside the band gap Eg of HAP, which depend on the concentration of Mn and change the photo-excitation energy of HAP, making its effective value Eg* less than the band gap Eg, and generally changing the photoelectronic properties of HAP. It was established that the energies of formation of the substitutions Mn/Ca depend on the position of the Ca atom (Ca1 or Ca2) and on the concentration of manganese. It has been shown that the replacement of calcium cations with manganese occurs predominantly at the Ca2 position.

In pursuit of sustainable human survival, the effective utilization of renewable energy has become critical to technological advancement. Ocean Thermal Energy Conversion (OTEC) technology, which generates electricity by leveraging the temperature differential between surface and deep ocean waters, enables stable power generation around the clock. In this domain, the combination of thermoelectric generators (TEGs) and heat exchangers has exhibited immense potential for ameliorating the deficiencies of conventional OTEC. This study uses numerical simulation to investigate the fluid dynamics characteristics of heat exchangers with flat fins and different types of longitudinal vortex generators (LVGs) under the same number of fins. The research encompasses heat exchangers with rectangular, triangular, and trapezoidal LVGs. Concurrently, the analysis examines how the vortices generated by the LVGs influence the thermoelectric performance of the TEGs. The results demonstrate that heat exchangers integrating flat fins and LVGs can enhance the power generation efficiency of TEGs. However, the pumping power required by the LVGs constrains the thermoelectric conversion efficiency. Compared to rectangular and triangular LVGs, trapezoidal LVGs achieve a superior balance between output and pumping power. Heat exchangers utilizing trapezoidal LVGs can attain the highest TEG thermoelectric conversion efficiency with a specific seawater flow velocity. Overall, these findings provide valuable reference information for applying TEGs and heat exchangers in OTEC design.

The integration of renewable energy and hybrid energy storage system (HESS) into electrified railways to build electric railway smart microgrid system (ERSMS) is beneficial for reducing fossil fuel consumption and minimizing energy waste. However, the fluctuations of renewable energy generation and traction load challenge the energy management effectiveness for such a complex system. In this work, an energy management strategy is proposed which firstly decomposes the renewable energy into low-frequency and high-frequency components by an integrated empirical mode decomposition (IEMD). Then, a two-stage energy distribution approach is utilized to appropriately distribute the energy flow among the ERSMS. Finally, the feasibility and effectiveness of the proposed solution are validated through case study.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

Our planet faces several serious and urgent challenges to sustainability, not just climate change. Most researchers argue that technological solutions can solve these problems. This review paper first examines the prospects for decoupling environmental damages in general from economic growth, considered at the global level, then looks at whether the recent advances in Information and Communication Technology (ICT) can help. It is argued that although absolute decoupling might have occurred in some countries, even after accounting for energy-intensive imports, it has not occurred at the global level, which is the relevant level for global sustainability problems. This conclusion is strengthened by the very high correlation over the past three decades found between GDP and several parameters relevant for sustainability, particularly for atmospheric CO2 ppm and ecological footprint as a function of Gross Domestic Product (GDP). ICT innovations relevant to energy use include smart grids and smart cities, especially smart urban transport. A review of recently published papers shows no definite findings of energy or carbon reduction, although some innovations show energy/carbon reduction potential, if given strong policy support. However, the needed policies could well give marked reductions even without ICT approaches. Overall, it is concluded that Earth’s sustainability challenges will necessitate deep energy reductions, which in turn require profound sociopolitical changes.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

The recent advancements in the field of communication have led data sharing to become an integral part of today's smart cities with the evolution of concepts such as the internet of vehicles (IoV) paradigm. As a part of IoV, Electric Vehicles (EVs) have recently gained momentum as authorities have started expanding their Low Emission Zones (LEZ) in an effort to build green cities with low carbon footprints. Energy is one of the key requirements of EVs not only to support the smooth and sustainable operation of EV itself but to also ensure connectivity between the vehicles and infrastructure with controlling devices like sensors and actuators installed within an EV. In this context, renewable energy sources (such as wind energy) dramatically play their parts in the automobile sector towards designing the energy harvesting electric vehicles (EH-EV) to pare the energy reliance on the national grid. In this article, a novel approach is presented to achieve electric generation due to vehicle mobility to support the communication primitives in electric vehicles which enables plenty of IoV use cases in the presence of surplus energy at hand. A small-scale wind turbine is designed to harness wind power for converting it into mechanical power. This power is then fed to the onboard DC generator to produce electrical energy. Furthermore, the acquired power is processed through a regulation circuitry to consequently achieve the desired power supply for the end load, i.e. the batteries installed. The suitable orientation for efficient power generation is proposed on ANSYS-based aerodynamics analysis. The voltages induced by DC generator at No-Load condition are 35V while at Full-Load 25V are generated at rated current of 6.9A, along with the generation of power at around 100W (at constant voltage) at the rated speed of 90 mph for nominal battery charging. Moreover, the acquired data can be monitored via an android application interface by using a Bluetooth module.

Zimbabwe has ambitious and laudable GHG mitigation targets. Compared to a coal based future emissions reductions by 33% per capita by 2030 are targeted, by implementing a set of identified nationally determined contributions (NDCs). If historical climate conditions continue, it can do this at low or negative cost. However, anticipated conditions may not continue, and of the planned emissions reductions in the NDCs, 88% would come from the expansion of hydropower, which is driven by rainfall. If climate change causes the extreme droughts witnessed in recent years to become more frequent, embarking on Zimbabwe’s NDC future (underpinned by its official system development plan) may be expensive and further cripple the economy. Note that the economy is already being strangled by constrained power supplies due to unusually dry conditions in the Zambezi river basin. If the NDC Future is pursued, but the climate becomes drier, proactive efforts might be made to overcome the power shortages. However, this may result in a rapid ramp up of greenhouse gas emissions if the country turns to coal to reinforce its system and increase its resilience against hydropower vulnerability and the costs that would otherwise ensue. If the country were to keep its NDC investments and supplement them with more aggressive deployment of clean adaptation options, strongly positive outcomes appear possible. Specifically, this would require increased deployment of renewable energy technologies, a restructured power market, and deep increases in energy efficiency investments. In so doing, the country would not only exceed its NDC targets, but also reduce costs in a manner that is climate resilient. This would not remove the country's need for hydropower and some level of coal reliance. However, it will introduce requirements to ensure flexibility in both hydropower and coal power production. For hydropower, power stations will need to provide and be recompensed for providing ‘balancing services’, that is, storing water and producing electricity when the wind is not blowing, nor sun shining. In order to ensure continuous output from mines, it may require intelligent stockpiling combined with dynamic forecasting. This would apply not only to production in Zimbabwe, but potentially for neighboring countries. Doing so would allow predictable mining activities, but allow electricity systems to absorb low cost, low carbon hydropower at high rainfall periods. To make the NDCs resilient via clean adaptation, strong institutional restructuring is required. However, internalizing those costs and moving to advanced market structures and business cases may strain the capacity of current institutions.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Ninety percent of the existing building stock in Europe was built before 1990. These buildings are in urgent need for a significant improvement of energy-efficiency through renovation. Regrettably, so far only five percent of renovation projects have been able to yield energy-saving at deep renovation level. State-of-the-art renovation solutions are available, but costly and lengthy renovation processes and incomprehensible technical complexities hinder the achievement of a wide impact at a European scale. This paper presents research on Plug-and-Play (PnP) technologies supported by Building Information Modelling (BIM) to provide affordable, interchangeable and quick-installation solutions to overcome the main barriers of building deep renovation.

The modulation instability of surface capillary-gravity water waves is analysed in a shear flow model with a tangential discontinuity of velocity. It is assumed that air blows along the surface of the water with a uniform profile in the vertical direction. Such a model, despite its simplicity, plays an important role in hydrodynamics as the reference model for investigating basic physical phenomena of wave-current interactions and acquiring insights into a series of complex phenomena. In certain cases where the wavelength of interfacial perturbations is much bigger than the width of the shear fow profile, the model with the tangential discontinuity in the velocity is adequate for describing physical phenomena at least within limited spatial and temporal frameworks. A detailed analysis of the air-flow conditions under which modulation instability sets in is presented. It is also shown that the interfacial waves are subject to dissipative or radiative instability when negativeenergy waves appear at the interface.

Steady-state Reynolds-Averaged Navier-Stokes (RANS) simulations are performed for a leading-edge inflatable wing for airborne wind energy applications. Expanding on previous work where only the inflatable leading edge tube was considered, eight additional inflatable strut tubes that support the wing canopy are now included. The shape of the wing is considered to be constant. The influence of the strut tubes on the aerodynamic performance of the wing and the local flow field is assessed, considering flow configurations with and without side-slip. The simulations show that the aerodynamic performance of the wing decreases with increasing side-slip component of the inflow. On the other hand, the chordwise struts have little influence on the integral lift and drag of the wing, irrespective of the side-slip component. The overall flow characteristics are in good agreement with previous studies. In particular, it is confirmed that at a low Reynolds number of Re=10^5, a laminar separation bubble exists on the suction side of this hypothetical rigid wing shape with perfectly smooth surface. The destruction of this bubble at low angles of attack impacts negatively on the aerodynamic performance.

The issue of water and energy crisis have been turned into global matters which need to be tackled jointly. Accordingly, floating solar power plants, in which photovoltaic modules are used on the surface of water infrastructures, has recently been attracting much interest. This system provides some additional advantages over the ground-based system such as conserving the land and the water and increasing the efficiency of the module. This study first reviews the relevant literature comprehensively and then evaluates the potential of using floating solar photovoltaic (FSPV) on some of Iran’s water infrastructures which have experienced a large amount of evaporation every year due to high solar radiation. To this end, the five important dam reservoirs are selected as the representatives of the five important watersheds in Iran, and the advantages of the FSPV plant is analyzed in terms of energy generation, evaporation reduction, economic and environmental aspects considering different coverage percentages of reservoir’s surfaces. Considering Iran's vast potential for solar radiation, and, on the other hand, huge energy demand and critical water situation, results indicated that Iran can effectively harness solar energy through FSPV systems which help conserve the water in addition to support sustainable energy production.

Coupling the Maxwell tensor to the Riemann-Christoffel curvature tensor is shown to lead to a geometricized theory of electrodynamics. While this geometricized theory leads directly to the classical Maxwell equations, it also extends their interpretation by giving charge density and mass density, and the four-velocity that describes their motion geometric definitions. These geometric definitions are reminiscent of General Relativity’s interpretation of mass in terms of the scalar curvature R and hint at the emergence of gravity. The gravitational theory that does emerge is shown to be equivalent to Einstein’s General Relativity augmented by an energy-momentum tensor term that mimics the properties of dark matter and/or dark energy. In summary, the proposed geometrization of the Maxwell tensor puts both electromagnetic and gravitational phenomena on an equal footing with both being tied to the curvature of space-time. Using specific solutions to the proposed theory, the unification brought to electromagnetic and gravitational phenomena, as well as the relationship of those solutions to the corresponding solutions of the classical Maxwell and Einstein field equations are compared.

In the current complex and uncertain macroeconomic situation, improving the inherent resilience of the new energy vehicle industry chain is the key to effectively addressing various risks and challenges, and achieving dynamic balance between high-quality industrial development and industrial chain security. Based on the basic concept of resilience and the actual situation of new energy vehicle industry chain development, this study constructs a comprehensive evaluation index system for the resilience of the new energy vehicle industry chain, which includes four dimensional first-level indicators of coping resistance, adaptive resilience, autonomous control and leading competitiveness. In addition, it is measured by combining the data related to the new energy vehicle industry chain in Changzhou City. Our study shows that the situation on the new energy vehicle industry chain is complicated, and the comprehensive evaluation index system is more favorable for evaluating its resilience level.

This paper is dedicated to examining dynamic dark energy models in the context of observational constraints and their implications for the universe's future. By integrating theoretical models with various observational data, we aim to provide a comprehensive view of how dynamic dark energy influences cosmic evolution and the universe's fate. This study tests these models against the latest observational evidence, including the Cosmic Microwave Background, supernovae, and large-scale structure surveys, to refine our understanding of the universe's accelerating expansion and the mysterious nature of dark energy.

In this investigation, the impact of reducing agent concentration on the synthesis of zinc oxide nanoparticles was examined. During the synthesis, an assessment of ionic conductivity was carried out, revealing a significant increase in conductivity prior to the introduction of the reducing agent, followed by a sharp decrease upon its addition. Characterization of the ZnO NPs involved UV-visible spectroscopy, scanning electron microscopy, Fourier Infrared Spectroscopy, and X-Ray Diffraction analysis. The outcomes suggest that the characteristics of the ZnO NPs are influenced by the concentration of the reducing agent during the synthesis process. Notably, the ZnO NPs synthesized with a higher concentration of reducing agent exhibited a narrower optical band gap and increased surface energy. Furthermore, employing a concentration of 0.5 v/v resulted in the rapid production of nanoparticles with relatively uniform sizes. Conversely, concentrations below 0.5 v/v lead to slow formation, while concentrations exceeding 0.5 v/v yielded non-uniform nanoparticles.

The adoption of Industry 4.0 technology is essential for achieving energy efficiency, a critical aspect of Sustainable Development Goal (SDG) no. 12 aimed at addressing climate change. Understanding the impact of Sustainable Attitudes, Digital Trust, and Uncertainty Avoidance is crucial in the decision-making process regarding the implementation of Industry 4.0 technology. The slow adoption of Industry 4.0 technology is attributed to non-technological factors or people, while the need to achieve energy efficiency targets necessitates examining the influence of Sustainable Attitudes and Digital Trust as supporting variables, along with Uncertainty Avoidance, on technology adoption. The study employed a quantitative explanatory research approach to investigate the relationships and impacts of variables. It centered on employees of Schneider Electric Indonesia, a global Industry 4.0 technology provider, with a sample of 189 employees selected through random sampling, incorporating a 5% margin error from Slovin formula. The analysis involved the use of Structural Equation Modeling (SEM) with AMOS version 26. Industry 4.0 technology is essential for fostering innovation and business expansion, leading to a sustainable environment by offering principles, guidance, and energy-efficient technologies for companies. The involvement of Sustainable Attitude, moderated by Uncertainty Avoidance, is vital in reaching energy efficiency goals through Industry 4.0 implementation.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

Peer-to-peer (P2P) energy trading could help address grid management challenges in a decentralizing electricity system, as well as providing other social and environmental benefits. Many existing and proposed trading schemes are enabled by blockchain, a distributed ledger technology (DLT) relying on cryptographic proof of ownership rather than human intermediaries to establish energy transactions. This study used an online survey experiment (n=2064) to investigate how consumer demand for blockchain-enabled peer-to-peer energy trading schemes in the United Kingdom varies depending on how the consumer proposition is designed and communicated. The analysis provides some evidence of a preference for schemes offering to meet a higher proportion of participants’ energy needs, and for those operating at the city/region (as compared to national or neighbourhood) level. People were more likely to say they would participate when the scheme was framed as being run by their local council, followed by an energy supplier, community energy organization, and social media company. Anonymity was the most valued DLT characteristic and mentioning blockchain’s association with Bitcoin led to a substantial decrease in intended uptake. We highlight a range of important questions and implications suggested by these findings for the introduction and operation of P2P trading schemes.

To address global warming, there is a worldwide effort to establish carbon-neutral energy plans. Given the characteristics of renewable energy generation, a diverse 'Energy Mix' consisting of various energy sources such as wind and solar power is crucial. In particular, the wind power is expected to continue expanding globally due to its sustainable nature. Furthermore, the expan-sion of offshore wind farm is making essential and a rapidly growing industry sector to be achieving carbon neutrality with limited land for construction. To facilitate the construction and operation of offshore wind farms, specialized vessels with dynamic positioning (DP) systems are essential such as Wind Turbine Installation Vessels (WTIVs) and Service Operating Vessels (SOVs). The purpose of this study is to predict and analyze the scale and structural changes in the fleet capacity of DP vessel, which is essential for offshore wind power construction as the offshore wind power industry develops using System Dynamics (SD) modeling. Specifically, this study aims to construct a demand forecasting model for DP vessel used in offshore wind farm con-struction based on SD methodology. The study aims to identify influencing factors by analyzing dynamic changes in system configurations over time and establishing causal relationships based on feedback structures. Instead of traditional time series analysis methods, causal relation-ship-based simulations were conducted for quantitative analysis. The results provide insights into the changes in the DP vessel market structure due to the emergence of the new industry and highlight areas that require improvement throughout the industry.

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

Renewable energy sources will play a central role in the sustainable energy systems of the future. Scenario analyses of such hypothesized energy systems require sound knowledge of the techno-economic potential of renewable energy technologies. Although there have been various studies concerning the potential of offshore wind energy, higher spatial resolution, as well as the future design concepts of offshore wind turbines, has not yet been addressed in sufficient detail. Here, we aim to overcome this gap by applying a high spatial resolution to the three main aspects of offshore wind potential analysis, namely ocean suitability, the simulation of wind turbines and cost estimation. A set of constraints is determined that reveal the available areas for turbine placement across Europe’s maritime boundaries. Then, turbine designs specific to each location are selected by identifying turbines with the cheapest levelized cost of electricity (LCOE), restricted to capacities, hub heights and rotor diameters of between 3-20 MW, 80-200 m and 80-280 m, respectively. Ocean eligibility and turbine design are then combined to distribute turbines across the available areas. Finally, LCOE trends are calculated from the individual turbine costs, as well as the corresponding capacity factor obtained by hourly simulation with wind speeds from 1980 to 2017. The results of cost-optimal turbine design reveal that the overall potential for offshore wind energy across Europe will constitute nearly 8.6 TW and 40.0 PWh at roughly 7 €_ct kWh^-1 average LCOE by 2050. Averaged design parameters at national level are provided in an appendix.

We mainly describe the influence factors of captured power by huge wave energy harvesters, which the vertical motion of buoy can transform ocean’s potential energy into piezoelectric energy power by waves. By means of semi-analytical solutions and theoretical analysis, related environmental coefficients are analyzed firstly and find the most appropriate wave frequency and geometric structure as reference. Secondly, the numerical results also discuss the impact trend of hydrodynamic parameters and geometric volume on motion, voltage and power with qualitative agreement. The simulation data confirm that structure parameters of the modified model could markedly deliver sufficient power to ocean high electrical equipment with long-time stability.

Obesity is a worldwide epidemic; hence it is crucial to understand how it can be effectively prevented/treated. Thus, obesity should be tackled considering that it is a multifactorial condition. This work examines a wide range of factors and attempts to understand which contribute most to variability in overweight/obesity. Eighty-four subjects with overweight/obesity were recruited. Dietary baseline information was obtained by analyzing three 24-hour recalls. Resting metabolic rate was measured using indirect calorimetry, physical activity through accelerometry, cardiometabolic parameters were determined in blood samples and body composition by anthropometry and bioimpedance. Factor analysis of principal components (PCA) was carried out (SPSS v22.0). Large interindividual variability was observed in dietetic, biochemical, and physical activity measurements (coefficient of variation ≥30%), but body composition was homogeneous. Volunteers had an unbalanced diet and low physical activity. PCA reduced the 26 analyzed variables into 7 factors, accounting for 81,5% of total data variability. The main factor was the ‘‘caloric and lipid factor’’ related to diet, responsible for 25.9% of total variability, followed by ‘‘adiposity factor’’ (16,9%) and ‘‘cardiometabolic risk factor’’ (13,2%). Diet seems to be the factor that contributes the most to data variability in people with overweight/obesity, especially the intake of lipids, energy and proteins.