Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

This manuscript explores sustainable agriculture's role in mitigating environmental challenges and meeting the nutritional needs of a growing global population. The objective is to assess the impact of different fertilizers on two distinct tomato-growing soils, each characterized by unique chemical and biological properties. The study compares four fertilizer treatments: Additionally, it evaluates the environmental implications of these fertilizers, focusing on their Carbon and Water Footprints. The findings indicate significant improvements in soil quality with SBO fertilizer. Both soils experienced a shift towards a near-neutral pH, increased organic matter content, and heightened microbial biomass. Enzyme activities were notably superior in SBO-treated soils. Life Cycle Assessment (LCA) results demonstrate that the SBO-based system is the most sustainable, with the lowest Carbon footprint. NPK exerts the highest environmental impact. The Water Footprint analysis aligns with these results, showing that SBO requires the least water for tomato production. In summary, this study underscores the significance of sustainable fertilization practices in improving soil quality and reducing environmental footprints in agriculture, offering potential benefits for food production and environmental conservation.

Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

This study investigates water consumption in two areas with limited water resources – the Salar de Atacama and Salar de Atacama-Vertiente Pacifico basins in Chile's Antofagasta Region – with the aim of developing strategies that incorporate social and environmental aspects into water management. A qualitative approach was employed that involved a focus group with four water management representatives and surveys of the general population (156 responses). Additionally, the current state of water rights in the basins was examined and the feasibility of the proposed strategies was assessed. The findings reveal that the mining industry's development approach is viewed negatively, mainly due to inadequate community engagement, confidential consumption data, and limited government oversight. Adopting a comprehensive water stewardship approach that considers social and environmental factors would help mitigate the adverse effects of mining on communities. Therefore, improved management and transparent collaboration among stakeholders are essential for responsible water resource use in mining.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

The limited availability of water resources worldwide presents obstacles, to the progress of ag-riculture. This situation calls for the implementation of water saving technologies to address these challenges effectively. The quest for technologies that conserve water in agriculture, par-ticularly within the context of cotton production, is related to the study of the impact of drought on the growth, leaf surface area, accumulation of dry matter, boll number, and productivity. The benefits of local drip irrigation have been established. Various models and strategies for opti-mizing and improving the efficiency of how we use water for irrigation purposes. In a market driven economy the effective utilization of water assetsis closely linked to the improvement of managing mineral nutrients. To enhance both the quantity and quality of production, nitrogen is the key factor element that plays a role in the process. The formation of highly efficient cotton crops by adapting the growing technology to the specific soil-climatic conditions of the area, in-cluding controlling nitrogen fertilizing and irrigation, is the primary method to achieve con-sistent harvests. The results of irrigation with water deficit and feeding plants with different fer-tilizer rates are presented. This matter is presently significant, in achieving dependable crop harvests supporting the economic growth of farms and safeguarding the well being of agricul-tural environments.

In recent years, a large-scale afforestation campaign has taken place in Inner Mongolia, China, to control desertification and soil erosion. However, the water consumption associated with large-scale afforestation significantly impacts the water resources in Inner Mongolia, resulting in a substantial ecological risk. This study aimed to evaluate the ecological risk of water resources caused by afforestation in the region. In this study, based on land cover data, Normalized Difference Vegetation Index (NDVI) data, and meteorological data, used trend analysis, water balance equation, and Water resources Security Index (WSI) index to analyze the ecological risks of water resources caused by afforestation in Inner Mongolia from 2000 to 2020. The results show that:(1) The afforestation area in Inner Mongolia was 5.37×104 km2 in 2000-2020; (2) Afforestation in arid and semi-arid areas leads to the reduction of water resources. (3) Afforestation reduces water resources in the study area by 0.76×108m3/year; (4) ~76% of afforestation regions face ecological risks of water resources.

The coastal zone of Bangladesh covers an area of 47,201 square km, 32% of the country, around 35 million people are living coastal zone, where about 15 million are women (Ahmad, 2019). Though the women of this area have a significant contribution in aquaculture, food production and economic growth of Bangladesh, still the health issues of women remain ignored, especially sexual and reproductive health issue. Women and girls experience heightened vulnerabilities to reproductive health problems in coastal areas. In aiming to investigate the prevalence of vaginal problems in coastal area the study has been designed. The study followed retrospective cohort study as a study design and use percentile and regression analysis to draw the result of the study. The study found that 94% of women are experiencing vaginal problems in coastal villages in Bangladesh. This number is about 05 times higher than the non-coastal villages and it also found water use for hygiene practice as a significant role for high rate of vaginal diseases in coastal areas of Bangladesh

Cotton is an important plant since it provides raw materials for various in-dustry bracnhes. Even though cotton is generally tolerant of drought, it is af-fected negatively by long-term drought stress. This experiment was conduct-ed according to a completed randomized plots trial design with 3 replications to determine the upland cotton genotype’s reactions against drought under controlled conditions in the 2022 year. All genotypes were watered with 80 mL-1 of water (100% irrigation, Field capacity) until three true leaves ap-peared. After this period water stress was applied at limited irrigation of 75% (60 mL-1), 50% (40 mL-1), and 25% (20 mL-1) of field capacity. After the trial terminated at 52. Days, the cv. G56, elit line G44, G5, and commercial variety G86 genotype, respectively resulted in the highest Root Length (RL), and the G76 genotype resulted in the lowest RL followed by G41 and G35 elite lines. G1 cultivar showed the highest Root Fresh Weight (RFW), followed by G56, G44, G86, G51, and G88, respectively. The lowest RFW was also obtained in elite lines G76 and G41. The third drought morphological marker, the Num-ber of Lateral Roots (NLRs), was the highest in G44, followed by G86, Cv. G56, elite lines G13 and G5 genotype. The lowest NLRs value was obtained in genotype G47 and G76. The highest RDW means was obtained in elite line G5, followed by Cv. G56, elite line G44, G75 and cv. G90, while the lowes RDW mean obtained in elite line G76, G35, and local varieties G20 and G61. In the SL marker, the highest averages were recorded for genotypes G35, G15, G26, G67, and G56, respectively. In the SFW marker, the highest averages were observed in genotypes G15, G52, G60, G31, and G68, respectively. The lowest SL values were observed in genotypes G91, G72, G32, and G22. Simi-larly, the lowest SFW values were found in genotypes G83, G2, G75, and G91. In another shoot drought marker, Shoot Dry Weight (SDW), the highest val-ues were obtained in genotypes G35, G52, G57, G41, and G60, respectively. Conversely, the lowest SDW values were observed in genotypes G65, G91, G4, G20, and G22. In conclusion, the commercial varieties with high averages in roots, namely G86, G56, G88, and G90, and the genotypes G67, G20, G60, and G57 showing tolerance in shoots, are suggested to be potential parent plants for developing cotton varieties resistant to drought. Using the culti-vars found tolerant in the current study as parents in a drought-tolerant vari-ety development Marker-assisted selection (MAS) plant breeding program will increase the chance of success in reaching the target after genetic diversi-ty analyses are performed. It is highly recommended to continue the plant breeding program with the G44, G30, G19, G1, G5, G75, G35, G15, G52, G29, and G76 genotypes which show high tolerance in both root and shoot sys-tems.

The perturbation in water balance rather than any change in salt content is the main cause of hyponatremia, the most frequent electrolyte abnormality defined as serum sodium concentration <135 mEq/L. Hyponatremia may be divided as mild (Na>120 mEq/L) or severe (Na<120 mEq/L) hyponatremia, most frequently observed in elderly ICU hospitalized patients. Based on tonicity hyponatremia may be hypotonic (decreased concentration of solute), isotonic, and hypertonic (falsely low sodium). According to the volume of the extracellular fluid (ECF) hyponatremia is further divided as hypovolemic, euvolemic, or hypervolemic hyponatremia. Finally, hyponatremia may develop rapidly as acute (<48 h) with usually severe symptoms, or slowly as chronic hyponatremia, being usually asymptomatic or with mild symptoms. Patient’s medical history and clinical symptoms and signs could point to a certain diagnostic direction. Acute severe hyponatremia is presented with headaches, vomiting, nausea, fatigue, impaired cognition, gait with increased falls symptoms etc., while the severe symptomatology due to hyponatremic encephalopathy is presented as confusion, agitation, seizures, or even coma and death. Nevertheless, an urgent evaluation of the volume and neurological status is essential for prevention of neurological damages. The treatment of hyponatremia should of course be based on the underlying cause, the duration and degree of hyponatremia, the observed symptoms, and volume status of patient.

It was for long time believed that lidar systems based on the use of high-repetition micro-pulse lasers could be effectively used to only stimulate atmospheric elastic backscatter echoes, and thus only exploited in elastic backscatter lidar systems. Their application to stimulate rotational and roto-vibrational Raman echoes, and consequently their exploitation in atmospheric thermodynamic profiling, was considered not feasible based on the technical specifications possessed by these laser sources until a few years ago. However, recent technological advances in the design and development of micro-pulse lasers, presently achieving high UV average powers (1-5 W) and small divergences (0.3-0.5 mrad), in combination with the use of large aperture telescopes (0.3-0.4 m diameter primary mirrors), allow to presently develop micro-pulse laser-based Raman lidars capable to measure the vertical profiles of atmospheric thermodynamic parameters, namely water vapour and temperature, both in daytime and nighttime. This paper is aimed at demonstrating the feasibility of these measurements and at illustrating and discussing the high achievable performance level, with a specific focus on water vapour profile measurements. The technical solutions identified in the design of the lidar system and their technological implementation within the experimental setup of the lidar prototype are also carefully illustrated and discussed.

Water deficit greatly affects global crop growth and productivity, particularly in water-limited environments like upland rice cultivation, leading to reduced grain yield. Plants activate various defense mechanisms during water deficit, involving numerous genes and complex metabolic pathways. Exploring orthologous genes, linked to enhanced drought tolerance, can aid functional validation in target species using genomic data from model organisms. Here, we studied the OsCPK5 gene in upland rice, an AtCPK6 ortholog from A. thaliana, by overexpressing it in the BRSMG Curinga cultivar. Transformants were assessed under two conditions: water deficit applied 79 days after seeding, lasting 14 days, followed by 7 days of irrigation at 80% field capacity. Physiological data and samples were collected at R3, R6, and R8 stages. GM plants consistently exhibited higher OsCPK5 gene expression across stages, peaking during grain filling. During this phase, GM plants displayed reduced stomatal conductance, photosynthetic rate, and increased water use efficiency compared to non-GM plants under drought. GM plants also exhibited higher filled grain percentage in both irrigation conditions. Their drought susceptibility index was 0.9 times lower than NGM plants, and they maintained a higher chlorophyll a/b index, indicating sustained photosynthesis. NGM plants under water deficit exhibited more leaf senescence, while OsCPK5-overexpressing plants retained green leaves. Overall, OsCPK5 overexpression induced diverse drought tolerance mechanisms, hinting at potential for future development of more drought-tolerant rice cultivars.

Maize, a crop of international relevance, frequently undergoes xylem embolism due to water shortage, negatively impacting growth, yield, and quality. Consequently, a refined comprehension of xylem embolism is vital for enhancing maize cultivation. Notwithstanding extensive research and the generation of analytical models for embolism mechanisms, prevalent models often disregard crop-specific hydraulic processes and the formation of embolisms via air bubbles in the xylem conduit. In this research, we present an inventive model applying pipe cavitation parameters to discern water potential and bubble formation in maize leaf xylem. The model integrates pivotal physiological traits of maize—leaf count, leaf vein count, and average leaf radius—demonstrating robust correlations. Furthermore, we constructed a percentage conductivity loss (PLC) curve based on pre-dawn leaf water potential and compared it with our model, offering interval data to observe embolisation events triggered by air bubbles. Utilizing experimental data, our novel cavitation-parameters based model effectively corresponds with observed bubble phenomena and appropriately characterizes water transport in plant xylem conduits. This method enabled us to observe the transition from bubble occurrence to cavitation embolism microscopically, which aligned with the embolism intervals provided by the model. This procedure reveals potential trends in bubble-induced embolism and deepens our knowledge of microscopic plant hydraulics and crop embolism. This work establishes a basis for understanding the generation of bubble embolisms in maize, assists in evaluating maize plant water status for efficient water supply management throughout the growth cycle, and contributes towards potential water management strategies for maize.

An experiment was conducted in 2016 & 2017 for development of novel rice hybrids for aerobic ecology with lesser yield penalties in comparison to irrigated ecosystem, further with added advantage of reduced methane emissions and water budget as witnessed in irrigated system. Based on the restorer / maintainer reaction and spikelet fertility (%), 10 restorer lines were selected to cross with 3 CMS lines in the line by tester fashion in Yasangi (summer) season 2016-17. Resulting 30 experimental hybrids besides 13 parental lines (10 Restorer lines and 3 B - lines of akin CMS lines) and checks (GK 5022, CR Dhan 201) assessed during Vankalam (rainy) season 2017 at three different places/locations viz., Rajendranagar, Warangal and Kampasagar. The outcome of experiment were two experimental hybrids viz., APMS-6A × HRSV – 7 and IR-79156A × ATR – 372, were categorized as stable hybrids with desirable sca effects, heterosis (ranging from 7% to 13%) over best check GK 5022 along with an in-essence performance for yield and other yield attributing characters.

Polymer electrolyte membrane water electrolyser suffers mainly from slow kinetics regarding oxygen evolution reaction (OER). Noble metal oxides, like IrO2, RuO2, are generally more active for OER than metal electrodes, exhibiting low anodic overpotentials and high catalytic activity. However, issues like electrocatalyst stability under continuous operation and cost minimization through reduction of the catalyst loading are of great importance for the research community. In the present study, unsupported IrO2 of various particle sizes (different calcination temperatures) were evaluated for the OER and as anode electrodes for PEM water electrolyzers [1]. The elec-trocatalysts were synthesized by the modified Adams method [2][3] and the effect of calcination temperature on the properties of IrO2 electrocatalysts is investigated. Physicochemical charac-terization was conducted using X-ray Diffraction, BET, High-Resolution TEM and XPS analyses. For the electrochemical performance of synthesized electrocatalysts in the OER, cyclic voltammetry and linear sweep voltammetry were conducted in a typical 3-cell electrode configuration, using glassy carbon as working electrode, where the synthesized electrocatalysts were casted on, in 0.5 M H2SO4 solution. The materials, as anode PEM water electrolysis electrodes, were further evaluated in a typical electrolytic cell using Nafion®115 membrane as electrolyte and Pt/C as cathode elec-trocatalyst. The IrO2 electrocatalyst calcined at 400°C shows high crystallinity with 1.24 nm particle size, high specific surface area (185 m2 g-1) and a high OER activity of 177 mA cm-2 at 1.8 V as anode electrocatalyst for PEM water electrolyzer.

The gradual decline of the Aral Sea’s water level over the past five decades poses a huge environmental problem in the heart of Central Asia. Uzbekistan, once blessed with abundant water resources, now struggles with water scarcity in certain regions. While global environmental issues contribute to some degree to this dilemma, irrigation mismanagement plays a central role. This study focuses on the widespread problem of irrigation mismanagement in Uzbekistan and specifically addresses the rural district of Oltinsoy in the southern province of Surkhandarya. The main objective of this research project is to propose effective measures that can alleviate the pressing problem of water scarcity in the region while emphasizing the urgent need for well-executed projects and careful maintenance to ensure long-term sustainability at the local level. It is important to note that this study does not include an examination of the impact of global warming on the decline of water resources in Uzbekistan.

Neonicotinoids (NEOs) have become the most widely used insecticides in the world since the mid-1990s. According to Chinese dietary habits, rice and water are usually heated before being consumed, but the information about the alteration through the heat treatment process is very limited. In this study, the parents of NEOs (p-NEOs) accounted for >99% of the total NEOs mass (∑NEOs) in both uncooked (median: 66.8 ng/g) and cooked (median: 41.4 ng/g) rice samples from Guangdong Province, China, while the metabolites of NEOs (m-NEOs) involved in this study accounted for less than 1%. We aimed to reveal the concentration changes of NEOs through heat treatment process, thus, several groups of rice and water samples from Guangdong were cooked and boiled, respectively. Significant (p < 0.05) reductions in acetamiprid, imidacloprid (IMI), thiacloprid, and thiamethoxam (THM) have been observed after the heat treatment of the rice samples. In water samples, the concentrations of THM and dinotefuran decreased significantly (p < 0.05) after the heat treatment. These results indicate the degradation of p-NEOs and m-NEOs during the heat treatment process. However, the concentrations of IMI increased significantly in tap water samples (p < 0.05) after heat treatment process, which might be caused by the potential IMI precursors in those industrial pesticide products. The concentrations of NEOs in rice and water can be shifted by the heat treatment process, so this process should be considered in relevant human exposure studies.

Due to the impacts from climate change, the allocation of water resources must urgently be optimized worldwide to ensure that the needs of both water managers and farmers are balanced. In this study, manager-oriented and farmer-oriented assessment models were developed for irrigation water optimization and allocation. The distance from water sources and hydraulic head were the main factors in the manager-oriented assessment model; crop value, water demand of crops, and soil type were additional factors in the farmer-oriented assessment model. The developed assessment models were used to assess irrigation water allocation in five villages in Neimen District. Cadasters at high elevation were discovered to not be suitable for cultivation of crops because of the difficulties in constructing irrigation facilities and the loss of irrigation water during transportation. The result obtained from the manager-oriented assessment system was related to the costs involved in the construction and maintenance of irrigation facilities, which indicated that cadasters located at long distances from water sources and at high elevation are unsuitable for cultivation. By contrast, the result obtained from the farmer-oriented assessment system was related to the profits of farmers and revealed that more cadasters would be suitable for cultivation if suitable crops were chosen.

Coagulation is the most sensitive step in drinking water treatment. Underdosing may not yield the required water quality, whereas overdosing may result in higher costs and excess sludge. Traditionally, the coagulant dosage is set based on bath experiments performed manually. Therefore, this test does not allow real-time dosing control, and its accuracy is subject to operator experience. Alternatively, solutions based on machine-learning (ML) have been evaluated as a computer-aided alternative. Despite these advances, there is open debate on the most suitable ML method applied to the coagulation process, capable of the most highly accurate prediction. This study addresses this gap, where a comparative analysis between ML methods was performed. As a research hypothesis, a novel data-driven fuzzy inference system (FIS) should provide the best performance due to its ability to deal with uncertainties inherent to complex processes. Although ML methods have been widely investigated, only a few studies report hybrid neuro-fuzzy systems applied to coagulation. Thus, to the best of our knowledge, this is the first study thus far to address the accuracy of this novel data-driven FIS for such application. The novel FIS provided the smallest error (0.86), indicating a promising alternative tool for real-time and highly accurate coagulant dosing in drinking water treatment.

This paper develops the study of the effect of powerful ultrasound on the laser breakdown of liquids and a comparative study of the possibilities of acoustic and optical diagnostics of breakdown. The method of laser-induced breakdown spectroscopy (LIBS) for elemental analysis of liquids, along with high efficiency, continues to be less sensitive compared to traditional chemical methods. The paper develops a method of using additional ultrasound irradiation of the laser breakdown area in order to increase the efficiency of LIBS. Using the developed technique, spectral lines of chemical elements such as potassium, manganese, sodium, calcium, etc. were obtained for the first time depending on the frequency and power of ultrasound. It is shown that a sharp increase in the intensity of spectral lines of elements in water during laser breakdown is observed in the field of high-power ultrasound. It indicates an increase in the sensitivity of the combined method of ultrasonic LIBS. Along with the optical spectrum, the spectral and energy characteristics of acoustic emission were studied. An automated complex for hydrophysical and spectral studies is described, which was tested in the Sea of Japan during the voyage No. 81 of the research vessel RV "Professor Gagarinsky" in August 2022.

Reference evapotranspiration (ETo) is a key agrometeorological index for rational irrigation management. The standard method for ETo estimation, proposed by FAO, is based on a complicated Penman-Monteith equation, requires great number of meteorological inputs thus making it difficult for practical use by farmers. To the moment, there are many alternative simplified approaches for ETo estimation, most of them are directed to cutting the number of required meteorological inputs for calculation. Among them, special attention should be paid to various temperature-based methods of ETo assessment. One of the temperature-based models for ETo computation was realized in free mobile app ETo Calculator (Ukraine). The app gives Ukrainian farmers an opportunity to assess ETo values on daily or monthly scale using mean air temperature as the only input. The goal of the study was to test the app accuracy comparing to FAO-based calculations in five key regions of Ukraine, each of which representing a particular climatic zone of the country. It was established that the app provides relatively good accuracy of ETo estimation even in raw (not adjusted to windspeed and relative air humidity) run; the results of statistical comparison with the FAO-calculated values are: R2 within 0.82-0.87, RMSE within 0.74-0.81 mm, MAE within 0.60-0.70, MAPE within 18.07-25.50% depending on the region. ETo Calculator (Ukraine) is a good alternative for complicated Penman-Monteith method and could be recommended for Ukrainian farmers to be used for irrigation management.

Water distribution networks are vital infrastructure, needed for providing consumers with sufficient water of appropriate quality. The cost of construction, operation, and maintenance of such networks is extremely large. The problem of optimization of a water distribution network is governed by the type of water distribution network and the size of pipelines placed in the distribution network. This problem of the optimal diameter allocation of pipes in a distribution network has been heavily researched over the past few decades. This study describes the development of a computer program, ‘Smart Optimization Program for Water Distribution Networks’ (SOP–WDN), which applies Genetic Algorithm to the problem of the least-cost design of water distribution networks. SOP–WDN demonstrates the application of an evolutionary optimization technique, Genetic Algorithm, linked with a hydraulic simulation solver EPANET, for the optimal design of water distribution networks. The developed program was applied to three benchmark water distribution network optimization problems and produced consistently good results. SOP–WDN can be utilized as a tool for guiding engineers during the design and rehabilitation of water distribution pipelines.

Shallow bathymetry inversion algorithms have long been applied in various types of remote sensing imagery with relative success. However, this approach requires that imagery with increased radiometric resolution in the visible spectrum is available. The recent developments in drones and camera sensors allow for testing current inversion techniques on new types of datasets. This study explores the bathymetric mapping capabilities of fused RGB and multispectral imagery, as an alternative to costly hyperspectral sensors. Combining drone-based RGB and multispectral imagery into a single cube dataset, provides the necessary radiometric detail for shallow bathymetry inversion applications. This technique is based on commercial and open-source software and does not require input of reference depth measurements in contrast to other approaches. The robustness of this method was tested on three different coastal sites with contrasting seafloor types. The use of suitable end-member spectra which are representative of the seafloor types of the study area and the sun zenith angle are important parameters in model tuning. The results of this study show good correlation (R2>0.7) and less than half a meter error when they are compared with sonar depth data. Consequently, integration of various drone-based imagery may be applied for producing centimetre resolution bathymetry maps at low cost for small-scale shallow areas.

Freshwater pond aquaculture is the prevailing fish culture system worldwide, especially in developing countries. Climate change outcomes and inadequate environmental practices challenge its sustainability. This study applies emergy synthesis to assess the environmental performance of freshwater pond aquaculture in Brazil, aiming to identify and propose practices towards sustainability. As a study model, nine semi-intensive lambari farms operating at three levels of management were evaluated: low (LC), moderate (MC) and high (HC) control. Results showed that the main inputs for LC were services (27-46%), feed (7-39%), and water (15-21%), while for the MC and HC farms, they were feed (35-49% and 17-48%, respectively) and services (33-39% and 26-36%, respectively). All farms required more than 60% of their emergy from purchased inputs, resulting in low emergy sustainability index (ESI = 0.1-0.5). Replacing animal protein and oil on diet composition by vegetal sources, using superficial water instead of springwater, increasing juvenile productivity, and controlling pond fertilization can lead all systems to higher efficiency and resilience, increasing sustainability.

Background: The study describes the comparison of different microbial load results of natural falling and dipping of the house fly (Musca domestica) in water and milk to investigate the possibilities of preventing the effect of the transferred pathogens from the house fly to our sources by pointing out the existence of antimicrobial factors within the house fly. Methods: Samples of house fly were collected from Jeddah and Makkah (Makkah region) and were directly transferred to the laboratory. Each house fly was packed in sterile test tubes. Each tube was opened oppositely to a larger test tube containing 10 ml of sterile tap water, and sterile water at pH 4.0 in other similar series of treatments to represent the reactions of stomach fluids. Later, the house flies were left for 20 seconds after reaching the water surface, and then cultured on different microbial media to evaluate the microbial load of the natural falling of the house fly. To evaluate the complete dipping of house flies in the water, two methods were tested by one complete dip for the flies for 20 seconds, and three times complete dipping for 20 seconds in water before evaluating the microbial load. The same methods were achieved on milk in a series of experiments and the microbial load was evaluated after the incubation at room temperature for three hours. Results: It was found that dipping treatments of house flies gave lower microbial contamination in water at pH 4.0 than neutral pH. The lower microbial load was also observed when dipping the house flies three times in water as compared to once dipping and natural falling treatments. It was also found that the complete dipping of house flies’ treatments in milk will reduce the microbial contamination as compared to natural falling treatments. Conclusion: The observed results support the presence of antimicrobial factors on the house fly.

Water mist fire suppression technology has attracted an increasing interest from the field of fire protection services such as fire safety for buildings, ships, spacecraft, libraries and museums due to its non-toxic and high efficiency in the suppression of a wide variety of fires. To support the technological development of water mist fire suppression system and its application areas, this review introduces the concept of water mist system and discusses its suppression mechanisms in comparison with other fire protection systems. The recent application areas of water mist system are surveyed for class A fires involving combustible solid materials such as wood, paper and textiles; class B fires involving flammable liquids such as petrol, oils, lubricants, paints and waxes; class C fires involving flammable gasses such as natural gas and liquefied petroleum gas; fires involving electrical (class E) equipment such as computers and information technology facilities; and the class F fires involving flammable cooking oils and fats. Finally, the paper concludes the review by identifying the current research trends, and providing the future direction for water mist technology and applications.

TiO₂ nanorod as a superior nanostructure has attracted a lot of attention to exert in the photocatalytic and photoelectrocatlytic applications in recent years. Nevertheless, its practical usage is restricted by a number of limitations such as the large band gap energy, the low rate of photo-induced carriers generation and the high rate of charge carriers recombination. Therefore in this study, incorporation of TiO₂ nanorod with WO₃ is proposed as a suitable approach to overcome these defects. In this regard, WO₃-TiO₂ nanorod was constructed by a facile one pot hydrothermal method in two incessant steps and was then employed as a potent photoanode for photoelectrocatalytic hydrogen generation. The morphology, elemental compositions and optical properties were characterized by the FESEM, EDS and DRS analysis, respectively. Furthermore, voltammetry analyses were performed to assay the photoelectrochemical features of WO₃-TiO₂ nanorod. The results confirmed that the incorporation of TiO₂ nanorod with WO₃ not only significantly made the band gap energy narrower (from 3eV to 2eV), but also dramatically intensified the photocurrent density and photoconversion efficiency from 1mA.cm^-2 to 1.8mA.cm^-2 and from 0.3% to 0.45%, respectively. As a consequence of improving optical properties and photoelectrochemical features, WO₃-TiO₂ nanorod could generate 2.43 mmol H₂ during 100 min under UV irradiation, which was 1.71 times more than hydrogen generated over pure TiO₂ nanorod

The novel coronavirus SARS-CoV-2, the causative agent of COVID-19, emerged in the human population in December 2019 and spread worldwide within a few short months. Much of the public health focus for preventing and mitigating the spread of COVID-19 has been on individual and collective behaviors, such as social distancing, mask-wearing, and hygiene. Yet it is equally important to recognize that these behaviors and health outcomes occur within broader social and environmental contexts. Factors within local communities, regional policy, race, history, personal beliefs, and natural- and built environmental characteristics affect underlying population health and the spread of disease. For example, COVID-19 has renewed attention to secure water and sanitation services and their importance in protecting human health. Many remote Alaskan communities are particularly vulnerable because of inadequate water and sanitation systems. In this paper, we describe how inadequate water and sewer services may place the inhabitants of remote Alaskan communities at higher risk of COVID spread. We argue that insufficient water security and inadequate sewer systems, along with household overcrowding, multigenerational residences, limited transportation options, limited medical facilities, and higher prevalence of chronic diseases could lead to a greater potential of COVID-19 transmission and to more severe disease outcomes in these communities.

The fabrication and characterisation of photo-anodes based on black-Si (b-Si) are presented using a photo-electrochemical cell in NaOH solution. Black-Si was fabricated by maskless dry plasma etching and was conformally coated by tens-of-nm of TiO2 using atomic layer deposition (ALD) with a top layer of CoO_x cocatalyst deposited by pulsed laser deposition (PLD). Low reflectivity R < % of Black-Si over the entire visible and near-IR (λ < 2 µm) spectral range is favourable in better absorption of light while an increased surface area facilities larger current densities. Photoelectrochemical performance of the heterostructured photoanode is discussed in terms of n-n junction between b-Si and TiO₂.

The “memory of water” experiments suggested the existence of molecular-like effects without molecules. Although no convincing evidence of modifications of water – specific of biologically-active molecules – has been reported up to now, consistent changes of biological systems were nevertheless recorded. We propose an alternate explanation based on classical conditioning of the experimenter. Using a probabilistic model, we describe not only the biological system, but also the experimenter engaged in an elementary dose-response experiment. We assume that during conventional experiments involving genuine biologically-active molecules, the experimenter is involuntarily conditioned to expect a pattern, namely a relationship between descriptions (or “labels”) of experimental conditions and corresponding biological system states. The model predicts that the conditioned experimenter could continue to record the learned pattern even in the absence of the initial cause, namely the biologically-active molecules. The phenomenon is self-sustained because the observation of the expected pattern reinforces the initial conditioning. A necessary requirement is the use of a system submitted to random fluctuations with autocorrelated successive states (no forced return to the initial position). The relationship recorded by the conditioned experimenter is, however, not causal in this model because blind experiments with an “outside” supervisor lead to a loss of correlations (i.e., system states randomly associated to “labels”). In conclusion, this psychophysical model allows explaining the results of “memory of water” experiments without referring to water or another local cause. It could be extended to other scientific fields in biology, medicine and psychology when suspecting an experimenter effect.

The megacities´ sewage creates socioeconomic dependence related to water availability in the nearby zones, especially in countries with hydric stress. The present paper studies the water balance progression of realistic scenarios from 2005 to 2050 in the Mezquital Valley, the receptor of Mexico City untreated sewage since 1886, allowing agriculture irrigation in unsustainable conditions. WEAP model calculated the water demand and supply. Validation was performed with outflows data of the Tula River and simulated three scenarios: 1st) Steady-state based on inertial growth rates, 2nd) Transient scenario concerned climate change outcomes, with minor influence in surface water and hydric stress in 2050; 3rd) Transient scenario perturbed with a planned reduction of 36% in the imported wastewater and the start-up of a massive Water Treatment Plant, allowing drip and sprinkler irrigation since 2030. In the 2005-2017 period, 59% of the agriculture depended on the flood irrigation with megacity sewage. The water balance scenarios evaluated the sectorial supply of the ground and superficial water. Drip irrigation would reduce 42% of agriculture demands, but still does not grant the downflow hydroelectric requirements, aggravated by the lack of wastewater supply since 2030. This research alerts about how present policies compromise future Valley demands.

Caribbean SIDS are among the most vulnerable to climate change which will have a disproportionate impact on local environments and economies. Whilst there is a growing literature on how Caribbean SIDS can adapt to become more resilient a question that has received little attention is with regard to migration as an unplanned response. It is recognised that events such as hurricanes and flooding can lead to internal relocation in the short term but societal responses to droughts through migration have not generally been investigated. This paper seeks to address this by considering the case of the island of Carriacou, part of the state of Grenada. Carriacou with its small population, limited land area and local economy, historically based on agriculture has had a high degree of migration. This is in part a response to limited economic opportunities. Environmental stress manifest through limited water availability, inappropriate land management and social conditions is likely to be exacerbated by climate change and variability. Resultant increases in the frequency and intensity of droughts, in the absence of proactive interventions, are likely to result in non-linear migration, both to Grenada itself and beyond.

The Safe Drinking Water Act Amendments of 1996 require community water systems in the United States to send consumers Consumer Confidence Reports (CCRs). CCRs contain information on detected contaminants and required educational information about drinking water. The authors of this study developed a survey to evaluate how utilities track consumer feedback, understanding, and the role of the CCR in shaping consumer perceptions about water quality. Responses from this survey indicate it is common for utilities to indirectly track the effectiveness of their CCRs, but few utilities indicated directly evaluating consumer understanding or the effect of CCRs on consumer perceptions.

The emission of mercury (II) from coal combustion and other industrial processes continues to be a concern and have local impact on water resources. The detection of these ions in water with sensitive but rapid testing methods is desirable for environmental screening and fieldwork. Nanoparticles of various chemistries have shown promise for this purpose, as they can be used in simple colorimetric analyses. Silver nanoprisms were chemically synthesized resulting in a blue reagent solution, that transitioned towards yellow and colorless solutions when exposed to Hg²⁺ ions at various concentrations. A rapid galvanic reduction of Hg²⁺ onto the nanoprism surfaces is apparently responsible for a change in shape towards spherical nanoparticles, leading to the change in color. There were no interferences by other metal ions in solution, and pH had minimal effect in the range of 6.5 to 9.8. The silver nanoprism reagent provided a detection limit of approximately 0.5 µM (100 µg/L) for mercury (II), which compares favorably with other nanoparticle-based techniques. Further optimization may reduce this detection limit.

The increasing occurrence of widespread drought phenomena is a global environmental emergency, especially for the effects of ongoing climate change on groundwater availability. Dry years and extreme temperatures are common drivers of current climate impacts all over the world, including, for example, freshwater supply for drinking and agriculture purposes, ecosystems, forestry, health, etc.. In this frame, to ensure temporal water availability in water-stressed areas, a sustainable groundwater management is an increasing challenge. Most of groundwater in the South-East Latium Region, Central Italy, as in the whole Apennine Mountains chain, is stored in karst aquifers. In this area important water resources are present, but even here in the last decades they are affected by groundwater depletion as a consequence of occurring drought events, the upward trend in the globally average temperature and the increasing of anthropogenic activities. Due to the lack of flow rates data of springs in many areas of Italy, the spring response modeling could be a useful tool for supporting a proper water resource management. Several research studies proposed methods based on relationships between spring discharges and rainfall data. The goal of this paper is to propose a model, based on rainfall-discharges cross correlations, in order to assess the spring flow rate patterns of Capodacqua di Spigno Spring, which is the main one in the study area. The results obtained using the developed model has been compared to an existing method that uses the SPI index for the estimation of the minimum annual spring discharge.

Best Management Practices (BMPs) are commonly used to control pollution in the river basins. Prioritization of BMPs helps improve the efficiency and effectiveness of pollution reduction, especially in Critical Source Areas (CSAs) that produce the highest pollution loads. Recently, the Dez River in Khuzestan, Iran, has become highly eutrophic from the overuse of fertilizers and pesticides. In this basin, dry and irrigated farming produce 77.34% and 6.3% of the Total Nitrogen (TN) load, and 83.56% and 4.3% of the Total Phosphorus (TP) load, respectively. In addition, residential, pasture, and forest land uses together account for 16.36% of the TN and 12.14% of the TP load in this area. The Soil and Water Assessment Tool (SWAT) was implemented to model the Dez River basin and evaluate the applicability of several BMPs, including point source elimination, filter strips, livestock grazing, and river channel management, in reducing the entry of pollution loads to the river. Sensitivity analysis and calibration/validation of the model was performed using the SUFI-2 algorithm in the SWAT Calibration Uncertainties Program (SWAT-CUP). The CSAs were identified using individual (sediment, TN, TP) and combined indices, based on the amount of pollution produced. Among the BMPs implemented, the 10 m filter strip was most effective in reducing TN load (42.61%), and TP load (39.57%).

Humans may be exposed to microbial pathogens at recreational beaches via environmental sources, such as water, sand, and aerosols. Although infectious disease risk from exposure to waterborne pathogens has been an active area of research for decades, sand is a relatively unexplored reservoir of pathogens and fecal indicator bacteria (FIB). Beach sand and water habitats provide unique advantages and challenges to pathogen introduction, growth, and persistence, as well as continuous exchange between habitats. Models of FIB and pathogen fate and transport in sandy beach habitats can help predict the risk of infectious disease from recreational water use, but filling knowledge gaps such as decay rates and potential for microbial growth in beach habitats is necessary for accurate modeling. Climatic variability, whether natural or anthropogenically-induced, adds complexity to predictive modeling, but may increase human exposure to waterborne pathogens via extreme weather events, warming of water bodies and sea level rise in many regions. The popularity of human recreational beach activities, combined with predicted climate change scenarios, could amplify the risk of human exposure to pathogens and related illnesses. Other global change trends such as increased population growth and urbanization are expected to exacerbate contamination events and the predicted impacts of increasing levels of waterborne pathogens on human health. Such changes will alter microbial population dynamics in beach habitats, and will consequently affect the assumptions and relationships used in population models and quantitative microbial risk assessment (QMRA). Here, we discuss the literature on microbial population and transport dynamics in sand-water continuum habitats at beaches, how these dynamics can be modeled, and how climate change and other anthropogenic influences (e.g., land use, urbanization) should be considered when using and developing more holistic, beachshed-based models.

In many regions where drinking water supply is intermittent and unreliable, households adapt by storing water in cisterns or rooftop tanks. Both intermittent supply and stored water can be vulnerable to contamination by microorganisms with deleterious health effects. The Guadalajara Metropolitan Area is a rapidly growing urban center with over five million residents where household storage is nearly ubiquitous. This pilot study was conducted in July 2018 to examine the microbiological quality of drinking water in Guadalajara. Samples were tested for free available chlorine residual, total coliform bacteria, and E. coli. A survey on access to water and public perspectives was also conducted. Water exiting rooftop tanks exceeded regulatory limits for total coliform levels in half of the homes studied. Piped water arriving at two homes had total coliform levels that far exceeded regulatory limits. No E. coli were detected in any of the samples. Only 35% of homes had a chlorine residual between the recommended 0.2 and 1.5 mg/L. Many homes reported unpleasant odors and colors. Only 7% of residents drank the piped water. Future studies are needed, especially during April and May when many homes reported a higher disruption to water service.

This paper analyses six major transitions in watershed management in the Lower Mississippi River from the early 19th century till present. A conceptual framework is developed for analysing the role of visions, agency and niches in water management transitions and applied to a historical case on water management in the Lower Mississippi River. It is shown that water management regimes change over time and that major transitions were preceded by niches, in which new visions were developed and empowered. The case shows that: (i) emerging visions play an important role in guiding transitions; (ii) agency enables the further diffusion of visions and niches; (iii) vision champions play an important role in transitions, but are not decisive; (iv) each transition has led to an extension of the number of societal functions provided, which has led to more complex water management regimes in which functions are combined and integrated; and (v) external landscape factors are important, as they can lead to awareness and urgency in important decision making processes.

Development of carbon nanomaterials for adsorption thus removal of organic pollutants from water is a progressive research subject. In this regard, carbon nanomaterials with bifunctionality towards polar and non-polar or even amphiphilic undesired materials is indeed attractive for further study and implementation. Here, we created carbon buckypaper adsorbents comprising amphiphilic (oxygenated amorphous carbon (a-COx)/graphite (G)) nanofilaments that can dynamically adsorb organic biomolecules (i.e. urease enzyme) and thus purify the wastewaters of relevant industries. Given the dynamic conditions of the test, the adsorbent was highly efficient in adsorption of the enzyme (88%) while permeable to water (2382 L.h-1.m-2), thus holds a great promise for further development and upscaling. A subsequent citric acid functionalization declined selectivity of the membrane to urease, implying the biomolecules adsorb mostly via graphitic domains rather than oxidized, polar amorphous carbon ones. The devised platform i.e. the urease functionalized buckypaper is optimally conductive (13 S.cm-1) and can be further employed as a biosensor. Accordingly, water treatment can be linked to biosensing via a nanostructured membrane.

Pollution of sub-surface water reservoirs mainly rivers and streams through contaminated water point sources (CWPS) was studied. The objective was to formulate a discrete time delay mathematical model which describes the dynamics of reservoir pollution using mixing-problem processes that involve single species contaminants such as nitrates, phosphorous and detergents. The concentration of pollutants was expressed as a function of the inflow and outflow rates using the principle for the conservation of mass. Systems of ODEs generated from principles of mixing problems were refined into a system of DDEs so that the concentration of pollutant leaving the reservoir at time would be determined at some earlier instant, for the delay. The formulated model is a mathematical discrete time delay model which would be used to describe the dynamics of sub-surface water reservoir pollution. The results from the validation of the model were analyzed to determine how time delays in the mixing processes affect the rate of particle movement in water reservoirs.

Elastic bodies entering the water might experience Fluid-Structure Interaction phenomena introduced by the mutual interaction between the structural deformation and the fluid motion. Cavity formation, often misleadingly named cavitation, is one of these. This work presents the results of an experimental investigation on the water entry of deformable wedges impacting a quiescent water surface with pure vertical velocity in free fall. The experimental campaign is conducted on flexible wedges parametrically varying the flexural stiffness, deadrise angle, and drop height. It is found that under given experimental conditions cavity pockets forms beneath the wedge. Their generation mechanism is found to be ruled by a differential between structural and fluid velocities, which is introduced by the structural vibrations. Results show that the impact force during water entry of stiff bodies is always opposing gravity, while in case of flexible bodies might temporarily reverse its direction, with the body that is being sucked into the water within the time frame between the cavity formation and its collapse. Severe impacts might also generate a series of cavity generation and collapses.

Water and sanitation facilities in sub-Saharan Africa and Africa in general are appalling and for the most part absent. Progress continues with respect to the development of plant materials as potent adsorbents, disinfectants, coagulants, flocculants, wetland species and lots more as substitutes for the dangerous chemical disinfectants. This research presents the potential of phyto-active components of Zanthoxylum zanthoxyloides and Gongronema latifolium as effective biocides against water microbial contaminants. Dry powder of Zanthoxylum zanthoxyloides and Gongronema latifolium were extracted and prepared into different concentrations with ethyl acetate and chloroform, ranging from 25 to 500 mg/ml. These fractions were then examined for antimicrobial activities against inherent bacterial and fungal water contaminants using disc diffusion assay. Fractions were afterwards screened for phytochemical active compounds using standard methods. Crude extracts of the different plant examined selectively comprise saponins, tannins, reducing sugars, anthraquinones, flavonoids, terpenoids, phlobatanins and alkaloids. All plant extracts showed broad spectrum antibiosis against selected gram positive and gram negative bacteria including E. coli, P. aeruginosa, Klebsiella sp, S. pneumoniae and B. cereus, as well as tested fungi, including A. niger, A. flavus, Trichoderma sp and Candida sp. While all extracts exhibited maximum antibiosis at 500 mg/ml, the chloroform extracts compared well than ethyl acetate extracts. The overall results revealed that antimicrobial activities of the plant extracts are dose dependent with comparative activity greater than that of commercial antibiotics at the concentration of extracts tested. E.coli was the most susceptible microbial isolate tested and represents the potential of the extract against a group of coliform which are important indicators of microbial pollution in water. Other microbial isolates also recorded sensitivity to extracts tested at varying degrees. The findings indicate that microbes tested were mostly susceptible to chloroform extract of Z. zanthoxyloides and G. latifolium except for the activity of ethyl acetate extract of Z. zanthoxyloide against E.coli. Results of phytochemical screening of the extract also showed the varied presence of alkaloids, saponins, tannins, flavonoids, terpenoids and anthraquinones The results indicated that plant materials investigated can be developed as effective biocides against water microbial contaminants

Degussa P25 is a benchmark form of TiO₂ used worldwide in photocatalysis studies. Currently no such benchmark exists for co-catalysts, which are essential for many photocatalytic reactions. Here, we present the preparation of Pt nanocluster co-catalysts on TiO₂ using an unmodified commercial source and equipment that is commonly available. Transmission electron microscopy reveals that the procedure produces TiO₂ decorated with Pt atom and nanoclusters (1-5 atoms). Optical reflectance and X-ray diffraction measurements show that the procedure does not affect the TiO₂ polymorph or UV-Vis absorbance. Gas phase photocatalytic splitting of heavy water (D₂O) shows that the Pt nanocluster decorated TiO₂ outperforms Pt nanoparticle (produced by photodeposition) decorated TiO₂ in D₂ production. Pt nanoclusters, produced directly from a commercial source, with high co-catalyst activity are prime candidates to be used in benchmark photocatalytic reactions.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

Urban lakes, especially those of natural origin, provide ecosystem services, recreation being one of the most important and highly valued by the city dwellers. Fulfilling the needs of city residents to relax and have contact with nature has become a priority in urbanized areas and has been proved to positively affect people’s health and well-being. The recreational potential of water bodies was identified to be most important aspect of ecosystem services to the residents of the neighboring areas. An assessment of recreational ecosystem services (RES) provisioning to society based on the real time spent by the citizens and housing values in the rural-urban gradient revealed that the economic benefits of lakes differ in urbanized, suburban and rural landscapes. The growth of cities has led to an increased population density in the surroundings of ecologically valuable areas, resulting in higher pressure from visitors seeking recreational areas. Along with urbanization, the impoverishment of ecosystem functions takes place, limiting their capability to provide ecosystem services. In this work provisioning of recreational ecosystem services of 28 floodplain lakes located along the urban-rural gradient of the Warsaw agglomeration was assessed. The relationship between the ecological value of the water bodies, measured using naturalness indices, and the recreational ecosystem services they can provide was assessed. The results showed that the floodplain lakes located along the urban-rural gradient are of a great importance to the citizens due to their recreational potential. The provisioning of recreational ecosystem services is poorly connected with the ecological characteristics of the floodplain lakes. Only hemeroby, was significantly correlated with provisioning, and there was no relationship with factors such as naturalness of vegetation or water quality, demonstrating that public preference was not generally influenced by high ecological quality. These data should be available to potential buyers and be integrated in spatial planning management plans in order to shape future housing policy.

The German wine sector has encountered new challenges in water management recently. To manage water resources responsibly, it is necessary to understand the relationship between the input of water and the output of wine, in terms of quantity and quality. The objectives of this study are to examine water use at the farm scale at three German wineries, and to develop and apply, for the first time, a quality-based indicator. Water use is analyzed in terms of wine production and wine-making over three years. After the spatial and temporal boundaries of the wineries and the water flows are defined, the farm water productivity indicator is calculated to assess water use at the winery scale. Farm water productivity is calculated using the AgroHyd Farmmodel modeling software. Average productivity on a quantity basis is 3.91 L wine per m3 of water. Productivity on a quality basis is 329.24 °Oechsle per m3 of water. Water input from transpiration for wine production accounts for 99.4–99.7% of total water input in the wineries, and, because irrigation is not used, precipitation is the sole source of transpired water. Future studies should use both quality-based and mass-based indicators of productivity.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

Using both GRACE satellite data and statistical records, we apply the advanced Super-SBM model in this study to evaluate the efficiency of water resource utilization in 34 prefecture-level cities across three provinces in Northeast China from 2003 to 2020. Furthermore, we employ the Tobit model to examine the factors influencing efficiency. Our findings suggest that while spatial clustering is moderately low, the efficiency of water resource utilization in the Northeast Region is praiseworthy and significantly correlates with the level of technological advancement. Four distinct categories can be identified among the prefecture-level cities based on the scale and technological efficiency of water resource utilization. To promote enhanced utilization of water resources, different regions should implement measures that are specifically tailored to their unique circumstances.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

A quasi-two-dimensional (quasi-2D) modelling approach is introduced to mimic transverse mixing of an inflow into a river from one of its banks, either an industrial outfall or a tributary. The concentrations of determinands in the inflow vary greatly from those in the river, leading to very long mixing lengths in the river downstream of the inflow location. Ideally, a two-dimensional (2D) model would be used on a small scale to capture the mixing of the two flow streams. However, for large-scale applications of several hundreds of kilometres of river length, such an approach demands too many computational resources and too much computational time, especially if the application will at some point require ensemble input from climate-change scenario data. However, a one-dimensional (1D) model with variables varying in the longitudinal flow direction but averaged across the cross-sections is too simple of an approach to capture the lateral mixing between different flow streams within the river. Hence, a quasi-2D method is proposed in which a simplified 1D solver is still applied but the discretisation of the model setup can be carried out in such a way as to enable a 2D representation of the model domain. The quasi-2D model setup also allows secondary channels and side lakes in floodplains to be incorporated into the discretisation. To show proof-of-concept, the approach has been tested on a stretch of the lower Athabasca River in Canada flowing through the oil sands region between Fort McMurray and Fort MacKay. A dye tracer and suspended sediments are the constituents modelled in this test case.

Hydrochemical and geophysical data collected during a hydrological survey in September 2017, reveal patterns of small-scale hydrological connectivity in a small water track catchment, north-European Arctic. Elevated tundra patches underlain by sands were disconnected from the stream and stored precipitation water from previous months. At the catchment surface and in the water track thalweg, some circular hollows, from 0.2 to 0.4 m in diameter, acted as evaporative basins with low d-excess values, from 2 to 4‰. Other hollows were connected to shallow subsurface runoff, yielding d-excess values between 12 and 14‰. ‘Connected’ hollows yielded a 50% higher dissolved organic carbon (DOC) content, 17.5±5.3 mg/L, than the ‘disconnected hollows, 11.8±1.7 mg/L. Permafrost distribution across the landscape is continuous, but highly variable. Open taliks exist under fens and small hummocky depressions, as revealed by electric resistivity tomography surveys. Isotopic evidence supports upward subpermafrost groundwater migration through open taliks under water tracks and fens/bogs/depressions, and its supply to streams via shallow sub-surface compartment. Temporal variability of isotopic composition and DOC in water track and a major river system, the Vorkuta R., evidence the widespread occurrence of the described processes in the large river basin. Water tracks effectively drain the tundra terrain and maintain xeric veg-etation over the elevated inter-track tundra patches.

Since the Paris Agreement in 2016, the goals of limiting climate change and moving toward climate resilience stand. With a share of about \SI{80}{\percent} of global \ce{CO2} emissions, the energy sector is an essential driver for these goals. A shift to low-carbon energy production and a decentralized system for more efficient energy transmission distribution is necessary. In this paper, we present our work on Modeling of Power Exchanges, Algorithms for \ac{LEM}, Competitiveness of \ac{CHP} and Energy Feedback Devices. The study was conducted considering technical, economic, social and regulatory framework. For easy integration into energy simulations or a \ac{DEMS}, a model for power exchanges was created that allows flexible input or deterministic price patterns. The algorithm handles the clearing of an \ac{LEM} by a district aggregator using limit orders with the goal of increasing the share of locally consumed electricity using economic incentives. An investigation was conducted into the operation of flexible \acp{CHP} in low-carbon power systems to balance the volatility of renewable energy. An energy signal light was developed as an energy feedback device, which is integrated into the \ac{DEMS} in a living lab and allows individual configuration. In summary, the results presented should be compared with those of other research approaches in the future and require qualitative and quantitative evaluation.

Pursuing sustainable energy solutions has prompted researchers to focus on optimizing energy extraction from renewable sources. Control laws that optimize energy extraction require accurate modeling, often resulting in time-varying, nonlinear differential equations. An energy-maximizing optimal control law is derived for time-varying, nonlinear, second-order, energy harvesting systems. We demonstrate that sustaining periodic motion under this control law when subjected to periodic disturbances necessitates identifying appropriate initial conditions, inducing the system to follow a limit cycle. The general optimal solution is applied to two point absorber wave energy converter models: a linear model where the analytical derivation of initial conditions suffices and a nonlinear model demanding a numerical approach. A stable limit cycle is obtained for the latter when the initial conditions lie within an ellipse centered at the origin of the phase plane. This work advances energy-maximizing optimal control solutions for nonautonomous nonlinear systems with application to point absorbers. The results also shed light on the significance of initial conditions in achieving physically realizable periodic motion for periodic energy harvesting systems.

The growing use of proton-exchange membrane fuel cells (PEMFC) in hybrid propulsion systems, aimed at replacing traditional internal combustion engines and reducing greenhouse gas emis-sions. Effective power distribution between the fuel cell and the energy storage system (ESS) is crucial, which has led to a growing emphasis on developing energy management systems (EMS) to efficiently implement this integration. To address this goal, this study examines the performance of a fuzzy logic rule-based strategy for a hybrid fuel cell propulsion system in a small hydro-gen-powered passenger vessel. The primary objective is to optimize fuel efficiency, with particular attention to reducing hydrogen consumption. The analysis is carried out under typical operating conditions encountered during a river trip. Comparisons between the proposed strategy with other approaches —control-based, optimization-based and deterministic rule-based— are con-ducted to verify the effectiveness of the proposed strategy. Simulation results indicated that EMS based on fuzzy logic mechanisms was the most successful in reducing fuel consumption. The superior performance of this method stems from its ability to adaptively manage power distri-bution between the fuel cell and energy storage systems.

Sustainable energy development (SED) is a crucial component of the Sustainable Development Goals (SDG), aiming to maintain economic and social progress while protecting the environment and mitigating climate change’s effects. SED serves as a transition paradigm for sustainable development, providing a blueprint for energy peace and prosperity for people and all uses. This article presents the history of SED and then uses a critical discourse approach to summarize existing review studies in SED. Ten interlinked themes of SED are identified, with two of them considered to be among the least studied in existing SED reviews and in the current global discussion around climate change. This study explores these two themes, which include energy financing and the need for 100% renewable energy (RE), a sub-theme of decarbonization strategy working towards the 1.5–2.0 °C scenario. The study suggests that the current G20 countries’ contributions, if maintained continuously per annum, in addition to 80% more funding from private investment compared to the amount in the 1.5 °C scenario financial requirements for clean energy, are sufficient to limit global warming. In addition to the present drive for 100% RE, the article also discusses emerging issues, such as energy storage options with an indication of hydrogen as the most promising, other energy-related development agendas, and the need for regional security stability to prevent energy wars. Selected SED decarbonization strategies are presented across the power, transport, building, and industrial sectors. The study concludes with progress and directions for future research, mainly the need for re-defining nationally determined contribution (NDC) through an emissions budgeting and centralized global or regional emissions stock-taking strategy working towards the 1.5 °C scenario.

Conventional methods of climate change (CC) mitigation have not ‘bent the curve’ of steadily rising annual anthropic CO2 emissions or atmospheric concentrations of greenhouse gases. This study reviews the present position and likely future of such methods, using recently published literature with a global context. It particularly looks at how fast they could be implemented, given that the limited time available for avoiding catastrophic CC (CCC). The study then examines solar geoengineering, an approach often viewed as complementary to conventional mitigation. The review next introduces equity considerations, and shows how this will shorten even further the time available for effective action for CC mitigation. The main findings are as follows. Conventional mitigation approaches will be implemented too slowly to be of much help in avoiding CCC, partly because some suggested technologies are infeasible, while others are either of limited technical potential, or, like wind and solar energy, cannot be introduced fast enough. Because of these problems, solar geoengineering is increasingly advocated as a quick-acting and effective solution. However, it could have serious side effects, and given that there will be winners and losers at the international as well as the more regional level, political opposition may make it difficult to implement. The conclusion is that global energy consumption itself must be rapidly reduced to avoid catastrophic climate change.

Background: Mitigating climate change requires fundamentally redesigned energy systems in which renewable energy sources ultimately replace fossil fuels such as natural gas. In this context, the question how and to which extent the gas sector can contribute to an increasingly climate-neutral future EU energy system is heavily debated among scholars, energy industry experts and policy makers. Methods: We take a two-step approach: We begin with a review of studies from energy industry and academia to discuss potential gas sector contributions from a holistic energy system design point of view; this is followed by a comprehensive discussion of technical potentials, micro-economic conditions and societal implications of renewable gas. We then enrich our findings with the results of an empirical focus group process. Results: The gas sector can not only contribute to balancing volatile renewable energy production but also enable the supply of renewable energy to end-users in gaseous form; based on existing infrastructure. This could reduce costs for society, increase public acceptance and ultimately speed up the energy system transformation. There is the theoretical technical potential to substitute major parts of natural gas with renewable gas of biogenic and synthetic nature. This, however, crucially requires a supportive policy framework like the one established for renewable electricity. Conclusion: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.

The United Nations Sustainable Development Goals call for the eradication of poverty, and China has proposed the Rural Revitalization Strategy based on the achievements of its poverty alleviation efforts in 2020. As a vital component of this strategy, the impact of land transfer on farmers' income growth has become a hot topic in both theoretical and practical sectors. This paper utilizes data from the CFPS database for the years 2010-2018 to construct OLS regression models and a Heckman two-stage model to analyze the effects of land transfers on the incomes of different types and sources among farmers. The empirical results show: First, land transfers do promote income growth among farmers, but the effect is primarily positive for those transferring out land, with negligible impact on those acquiring land. Second, the impact of land transfers varies between different types of income for transferees and transferors. Wage income contributes up to 88.26% to the income growth of transferors, a significantly higher rate than the decrease in business income; however, the increase in business income for transferees does not offset the decline in wage income, leading to no significant change in overall income. Further sensitivity analysis using the Heckman two-stage model confirms the robustness of these findings. The conclusions of this study provide theoretical and empirical evidence to optimize land transfer policies, enhance participation in land transfers, and ultimately achieve the mission of rural revitalization.

Revealing the multidimensional value of cultivated land resources, improving calculation methods, and exploring their spatial distribution characteristics and influencing factors are crucial for the enhancement of natural resource accounting system and the protection of cultivated land resources. This study take Guangxi, China as an example and construct a comprehensive multidimensional value evaluation system for cultivated land resources at the county scale. The income capitalization method, substitution market method, and value equivalent correction method were applied to calculate the economic, social, and ecological values of cultivated land resources in 111 counties. Furthermore, spatial autocorrelation analysis was employed to study their distribution characteristics and influencing factors. The results show that: (1) The total value of cultivated land resources in Guangxi reach 19,729.2 billion yuan, and the average cultivated land value is 5.3511 million yuan/hm2, of which the ratio of economic, social and ecological values is about 6:1:2; (2) The value of cultivated land has a certain distribution pattern in the global space, and the average economic and social value show the spatial distribution patterns of "low in the west and high in the east" and "low in the northwest and high in the southeast" respectively."(3) There is a significant spatial clustering effect of all values of cultivated land resources in local space, with "high-high" and "low-low" clustering. (4) Economic development level is significantly negatively correlated with the ecological value of cultivated land, while has a significant positive correlation with social value; (5) Natural conditions, economic development and agricultural development approaches are the key factors affecting the value of cultivated land resources.

A land cover map of two arctic catchments, nearby the Abisko Scientific Research Station, was obtained from a classification of a Sentinel-2 satellite image and a ground survey performed in July 2022. The two contiguous catchments, Miellajokka and Stordalen, are covered by various ecotypes, from boreal forest to alpine tundra and peatland. Two classification algorithms, support vector machine and random forest, were tested and gave very similar results. The percentage of correctly classified pixels was over 88% in both cases. The developed workflow relies solely on open source software and acquired ground observations. Space organization was directed by the altitude as demonstrated by the intersection of the land cover with the topography. Comparison between this new land cover map and previous ones based on data acquired between 2008 and 2011 shows some trends of vegetation cover evolution in response to climate change in the considered area. This land cover map is key input data for permafrost modeling, and hence for the quantification of climate change impacts in the studied area.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

Habitat quality has great significance for regional ecological conservation and human welfare. In this study, we evaluated the spatial and temporal characteristics of land use and habitat quality in the temperate desert sub-region of Ordos Plateau using patch-generating land use simulation (PLUS) and integrated valuation of ecosystem services and trade-offs (InVEST) models. From 2000 to 2020, the areas of grassland, cropland, and unused land in the study area increased significantly; the areas of water bodies and woodland increased slightly; and the area of wasteland decreased significantly. Moreover, the habitat quality in the temperate desert subzone of the Ordos Plateau showed a trend of increasing and then decreasing from 2000 to 2020. The areas of lower and low habitat quality first decreased and then increased, and the overall area decreased over time. Conversely, the areas of high and higher habitat quality initially increased and then decreased, and the overall area increased over time. The area of medium habitat quality first decreased and then increased, although the overall change was minimal. Based on the PLUS model, the habitat quality of the study area in 2025 predicted under the natural development scenario was compared with that predicted under the ecological conservation scenario, showing higher habitat quality and lower habitat degradation under the ecological conservation development scenario. These results can be used to provide a scientific basis and decision reference for the sustainable use of land resources and high-quality socio-economic development in the temperate desert sub-region of the Ordos Plateau.

During disaster response, clouds or darkness can prevent the use of optical images for detecting consequences of natural disasters, including landslides. In these situations, radar images can be used to detect changes more rapidly. However, Synthetic Aperture Radar (SAR) backscatter intensity images are underutilized for landslide detection. Unfortunately, there remains a lack of understanding about how to interpret landslide signatures in SAR imagery. In this study, we investigate how the morphometric features and material properties of landslides, and preexisting land cover, control their expression in SAR backscatter intensity change images. Trends in the spatial and temporal signatures of over 1000 landslides in 30 diverse case studies are investigated, using multi-temporal composites and dense time-series of Sentinel-1 C-band SAR backscatter intensity data. The results show that the orientation of landslide surfaces relative to the sensor, pre-existing land cover, and the roughness of the landslide surface, determine whether landslides will produce an increase or decrease in backscatter intensity values. In certain cases, we can identify morphometric features of landslides (e.g. scarps, transit zone, deposits, ponding) and material properties. Generally, we see that landslides appear most clearly with a strong increase in intensity when they occur in herbaceous vegetation or non-vegetated ground surfaces, due to an increase in surface roughness. While in forested or densely vegetated areas, landslides produce a more complex signature with both decreases due to radar shadow and vegetation removal, and an adjacent edge of increased intensity due to double bounce and direct return from vertical tree trunks and convex edges. In most cases, rough deposits produce an increase in intensity, while smooth deposits (e.g. from mudslides) exhibit specular reflection, and thus show decreased values. Landslides are less visible in cases with pre-event very rough ground, or mixed vegetation conditions. The conceptual model developed can aid interpretation of landslides in SAR imagery, and provide domain knowledge needed to train models for automatic landslide detection.

As a rapidly growing coastal megacity, Shanghai is continuously threatened with land subsidence issues since 1920s. Land subsidence was controlled in 1960s, however in 1990s, unconscious and dangerous urban underground space (UUS) exploration and tunneling development are causing further land subsidence. It is imperative to study previous relations towards future adaptive and resilient scenario modelling and planning. There are multiple cause-effect factors determined in the urban built environment of Shanghai megacity. This paper presents the current evidence based on the relations of the multifactor of the spectrum. Methods consist of understanding the cause-effect relations and spatiotemporal from the crucial period of 1960-2020. Data are collected secondarily from multiple open sourced databases. The results determine Shanghai are highly influenced by the UUS development induced-subsidence, tunneling leakage and weak spatial modelling. Spatiotemporal pattern has shown a mixed positive-negative impact: population, land subsidence is growing in parallel distribution (positive) with tunneling leakage, construction of tunneling, metro system, UUS development, building price, reconstruction area, GDP growth, land price, arable land decrease and further tunnel settlement in Urban City Centre, Pudong New Area, Minhang, Baoshan and Songjiang districts. These results are useful for further adaptive and resilient scenario modelling and spatial planning.

To investigate the dynamics of land surface temperature (LST) in Afghanistan in the period 2000-2021 and to assess the impact of such factors as soil moisture, precipitation, and vegetation coverage on it, remotely sensed soil moisture data from Land Data Assimilation System (FLDAS), precipitation data from Climate Hazards Group Infra-Red Precipitation with Station (CHIRPS), and NDVI and LST from Moderate Resolution Imaging Spectroradiometer (MODIS) were downloaded and correlations between them were analyzed using the regression method. The result shows that the LST in Afghanistan has a slightly decreasing, but insignificant trend during the study period (R=0.2, p-value=0.25), while vegetation coverage, precipitation, and soil moisture had an increasing trend. It was revealed that soil moisture has the highest impact on LST (R=0.7, p-value=0.0007), and the soil moisture, precipitation, and vegetation coverage explain almost 80% of spring (R2=0.73) and summer (R2=0.76) LST variability in Afghanistan. The LST variability analysis done separately for Afghanistan’s rivers subbasins shows that the LST of the Amu Darya subbasin had an upward trend in the study period, while for the Kabul subbasin the trend was downward.

Japan Aerospace Exploration Agency (JAXA) is going to launch Advanced Land Observing Satellite 3 (ALOS-3) after 2022. ALOS-3 satellite is capable of observing global land areas with wide swath (4000 km along-track direction and 70 km cross-track direction) at high spatial resolution (panchromatic: 0.8m, multispectral: 3.2m). Maintenance and updating of land cover and vegetation information at national level is one of the major goals of the ALOS-3 mission. This paper presents the potential of simulated ALOS-3 images for the classification and mapping of land cover and vegetation types at Genus-Physiognomy-Ecosystem (GPE) level. We acquired and simulated WorldView-3 images according to the configuration of the ALOS-3 satellite sensor and the simulated ALOS-3 images were utilized for the classification and mapping of land cover and vegetation types in three sites (Hakkoda, Zao, and Shiranuka) in northern Japan. This research dealt with 17 land cover and vegetation types in Hakkoda site, 25 land cover and vegetation types in Zao site, and 12 land cover and vegetation types in Shiranuka site. Ground truth data were newly collected in three sites, and we employed eXtreme Gradient Boosting (XGBoost) classifier with the implementation of 10-fold cross-validation method for assessing the potential of ALOS-3S images. The classification accuracies obtained in Hakkoda, Zao, and Shiranuka sites in terms of f1-score were 0.810, 0.729, and 0.805 respectively. The fine scale (3.2m) land cover and vegetation maps produced in the study sites showed clear and detailed view of the distribution of plant communities. Regardless of the limited number of the temporal images, ALOS-3S images showed high potential (at least 0.729 F1-score) for the land cover and vegetation classification in all three sites. The availability of more cloud free temporal scenes is expected for improved classification and mapping in the future.

This paper compares the Medieval (ca. 400–1500 CE) dynamics of forests from low-mountain (Montcortès; ca. 1000 m a.s.l.) and high-mountain (Sant Maurici; 1900 m a.s.l.) areas of the Iberian Pyrenees, both of which experienced similar climatic forcing but different anthropogenic pressures. The main aim is to identify forest changes over time and associate them with the corresponding climatic and anthropogenic drivers (or synergies among them) to test how different forests at different elevations respond to external forcings. This could be useful to evaluate the hypothesis of general Pyrenean deforestation during the Middle Ages leading to present-day landscapes and to improve the background for forest conservation. The study uses palynological analysis of lake sediments, historical documents and paleoecological reconstructions based on pollen-independent proxies. The two sites studied showed different forest trajectories. The Montcortès area was subjected to intense human pressure during regional deforestation up to a maximum of ca. 1000 CE. Further forest recovery took place until the end of the Middle Ages due to a change in forest management, including the abandonment of slash-and-burn practices. Climatic shifts indirectly influenced forest trends by regulating human migrations and the resulting shifts in the type and intensity of forest exploitation. The highland Sant Maurici forests exhibited a remarkably long-standing constancy and an exceptional resilience to climatic shifts, which were unable to affect forest extension and composition, and to local human pressure, from which they rapidly recovered. The Montcortès and Sant Maurici records did not follow the rule of an irreversible forest clearing during the Middle Ages leading to present-day landscapes. The present Montcortès landscape was shaped after a Medieval forest recovery, a new Modern-Age deforestation and a further forest recovery during the last centuries. The Sant Maurici forests remained apparently untouched since the Bronze Age and were never cleared during the Middle Ages. The relevance of these findings for forest conservation is briefly addressed, and the need for the development of more high-resolution studies on Pyrenean forest dynamics is highlighted.

The rural population percentage decreased from 82.7% to 68.9% in 2011, even though there is an increase in the total rural population, which stands at 833.7 million, and the rural population were now more than three times compared to the population seven decades ago. Another observation is the decrease in cultivators percentage from 71.9% to 45.1 %, while agriculture labour increase from 28.1% to 54.9% during the same period. Despite the increase in irrigated land and net area sown, the average holdings' size under the farmers is continuously decreasing, and it requires a study to look into the reasons. The research probes the role of Minimum Support Price (MSP) in supporting farmers and measuring market price above MSP needed to help marginal and small farmers remain above the poverty level. It explains how different market rates above MSP have a different impact on different categories of agriculture landholding. The study works on developing a common model that relates the impact of MSP on different farmers categories. The model can be generalized to all crops and regions and useful in designing policies that focus on uplifting the income of agricultural farmers.

The Ituri-Epulu-Aru landscape (IEAL) is experiencing deforestation and forest degradation. This deforestation is at the root of many environmental disturbances in a region characterized by endemism in biodiversity. This article focuses on the triangulation of spatialized prospective scenarios in order to identify future trajectories based on the knowledge of historical dynamics through the diachronic analysis of three satellite images (2003-2010-2014-2016). The scenarios were de-signed in a supervised model implemented in the DINAMICA EGO platform. The three scenarios Business-As-Usual (BAU), Rapid Economic Growth (REG) and Sustainable Management of the Environment (SME), extrapolating current trends, show that by 2061 this landscape will always be dominated forests (+ 84%). Old-growth forests occupy 74.2% of the landscape area in the BAU scenario, 81.4% in the SEM scenario and 61.2% in the REG scenario. The SEM scenario gives hope that restoration and preservation of biodiversity priority habitats is still possible if policy makers become aware of it.

Land and property development process include a series of multifaceted activities ranging from purchasing to converting it for development purposes and everything in between. The process itself encompasses multiple stakeholders, drivers, and contributions from diversified public and private actors and transaction cost arises out of their complex interaction. Transaction costs incurred during any kind of human interactions (i.e. transactions). Every actor involved in the process wishes to maximize his achievement under various constraints and hence institutional arrangement (i.e. set of humanly devised rules to administer the constraints) is necessary for efficient management of the development process. Therefore, to devise an optimum outcome out of economic and social transactions in the property development process, cooperative and competitive relationships between individuals should be understood from a broader socio-political and governance structure. In this research, it is critically argued that land and property development process should implicate a multifaceted set of formal and informal rules or institutional arrangement to govern the intrinsic interaction, action and thereby reducing the related transaction cost. The argument is further reproachfully evaluated and implicated in the urban development process through the myopic lens of Transit-oriented development (TOD) pathway. A vigilant combination of descriptive and explanatory research approach is adopted to analyze the connection between theory and practice.

Land cover and climate changes greatly influence hydrologic responses of a basin. However, the response vary from basin to basin depending on the nature and severity of the changes and basin characteristics. Moreover, the combined impacts of the changes affect hydrologic responses of a basin in an offsetting or synergistic manner. This study quantified the separate and combined impacts, and the relative contributions of land cover and climate changes on multiple hydrological regimes (i.e., surface runoff, streamflow, groundwater recharge evapotranspiration) for the Dhidhessa Subbasin. Land cover and climate change data were obtained from a recent study completed for the basin. Calibrated Soil and Water Analysis Tool (SWAT) was used to quantify the impacts. The result showed that SWAT model performed well for the Dhidhessa Subbasin in predicting the water balance components. Substantial land cover change as well as an increasing temperature and rainfall trends were reported in the river basin during the past three decades. In response to these changes, surface runoff, streamflow and actual evapotranspiration (AET) increased while groundwater recharge declined. Surface runoff was more sensitive to land cover than to climate changes whereas streamflow and AET were more sensitive to climate change than to land cover change. The combined impacts played offsetting effect on groundwater recharge and AET while inconsistent effects within study periods for other hydrologic responses. Overall, the predicted hydrologic responses will have negative impacts on agricultural production and water resources availability. Therefore, the implementation of integrated watershed management strategies such as soil and water conservation and afforestation could reverse the negative impacts.

The Soil Conservation Service - Curve Number (SCS-CN) method is extensively used to calculate the runoff from rainfall over a large catchment over the world. Slope is an important criterion for runoff but a very few attempts have been made to evaluate the effect of slope on the CN with runoff potential. The objective of this paper is to summarise the historical review on the effects of slope on CN and runoff potential in various regions by the hydrologists. This paper also depicts that how the various researchers proved the importance of consideration of slope for CN and runoff estimation. In addition, paper highlights the key features of research in future like to classify the watersheds on slope based CN, accurate Antecedent Moisture Condition (AMC) and proper initial abstraction in the various regions etc. Considering these parameters an accurate runoff estimation can be predicted and managed properly in the urban watersheds.

The Covid-19 has hit Italy in February 2020 after its outbreak in China at the beginning of January. But why Italy first among Western countries? What are the conditions that made Italy more vulnerable and the first target of such disease? What characteristics and what diffusion patterns could be highlighted and hypothesized, from the outbreak to the end of March 2020, after containment measures - including a national lock down – were introduced? In this paper we try to provide some answers to these questions, analyzing the issue from the medical, geographical and planning points of view. In particular, we started from a hypothesis of very similar economic, geographical, climatic and environmental conditions of the areas of Wuhan – in Hubei Province in China, the outbreak of the epidemics – and the Po Valley area – in Italy – where most cases and deaths were registered. Adopting an ecological approach, we compared the spatial distribution and pattern of Covid-19-related mortality in Italy with several geographical, environmental and socio-economic variables at Provincial level, analyzing them by means of spatial analytical techniques as LISA – Local Indicators of Spatial Association. Possible evidence relating Covid-19 cases and Nitrogen-related pollutants and land take arise, particularly in the Po Valley area.

Section 25(2) of the Constitution of South Africa protects property rights and the White Paper on Land Reform demonstrate tolerance and wisdom in the application of land reform policies. The central argument to this research was whether amendment of Section 25 (2) of the constitution to allow expropriation of land without compensation redresses redistribution of land for social cohesion and political stability. The researcher argues that, currently, Section 25 of the constitution provides for expropriation without compensation but at the same time protects property rights reducing the pace of redistribution. Hence, an amendment of section 25 (2) may remove the property right clause and accelerate expropriation without compensation. But whether the removal of the property right clause and acceleration of the process of expropriation without compensation will result to equitable and fair distribution of land to the majority of landless South Africans is not certain. The study concludes that, amendment of Section 25(2) is a justifiable process and priorities must be given to equity in redistribution to the majority landless at the margins of communities and not elites. If the amendment of Section 25 (2) cannot guarantee equity in redistribution for all ill respective of race, social cohesion, political stability and economic growth, intra-racial tensions may emerge. Such tensions may further compound the land question and affects investors’ confidence in South Africa.

The impact of ponds on basins has recently started to receive its well–deserved scientific attention. In this study, pond–induced impacts on soil erosion and sediment transport were investigated at the scale of the French Claise basin. In order to determine erosion and sediment transport patterns under current conditions, the CORINE erosion and SWAT models were used. The impact of ponds on the studied processes was revealed by means of land cover change scenarios, using ponded versus pondless inputs. Results show that under current conditions (pond presence), 12.48% of the basin corresponds to no–erosion risk zones (attributed to the dense pond network), while 65.66% corresponds to low–erosion risk, 21.68% to moderate–erosion risk and only 0.18% to high–erosion risk zones. The SWAT model revealed that ponded sub–basins correspond to low sediment yields areas, in contrast to the pondless sub–basins, which yield appreciably higher erosion rates. Under the alternative scenario, erosion risks shifted to 1.12%, 0.52%, 76.8% and 21.56% for no, low, moderate and high–erosion risks, respectively, while the sediment transport pattern of the Claise completely shifted to higher sediment yield zones. This approach solidifies ponds as powerful man–induced modifications to hydro/sedimentary processes.

Threats to natural ecosystems are closely linked to human development, and the lack, insufficiency or inefficiency of public policies are some of the most important drivers of negative effects on the environment. The contribution of the IUCN’s Red List of Ecosystems (RLE) to conservation topics has been discussed in previous studies; however, to date its implications for conservation in public policies have not been addressed. This perspective discusses how the RLE may support the improvement and development of these policies, specifically through the implications for public policy of each of the criteria that substantiate the threat status of ecosystems. We aim to provide a plausible baseline to the operationalization of RLE in public and conservation policy, facilitating the work of governments, practitioners and decision makers. Finally, we provide recommendations and examples as to how to proceed in creating and modifying different public policy instruments, such as land-use planning, spatial zoning, tax reduction, compensation schemes, climate change adaptation plans, management of introduced species, development offsets and restoration investment. This perspective contributes to implement RLE into public policy and to improve ecosystem conservation by expanding the current scope of RLE into practical and political dimensions through plausible actions, policies and strategies.

Damage to crops from wildlife interference is a common threat to food security among rural communities in or near Game Management Areas (GMAs) in Zambia. This study uses a two-stage econometric model and cross-sectional data from a survey of 2,769 households to determine the impact of land use planning on the probability and extent of wildlife-inflicted crop damage. The results show that crop damage is higher in GMAs as compared to non-GMAs, and that land use planning could be an effective tool to significantly reduce the likelihood of such damage. These findings suggest that there is merit in the current drive to develop and implement land use plans as means to minimize human-wildlife conflict such as crop damage. This is especially critical as Zambian conservation policies do not have an explicit provision for compensation in the event of damage from wildlife.

Land Surface Temperature (LST) is routinely retrieved from remote sensing instruments using semi-empirical relationships between top of atmosphere (TOA) radiances and LST, using ancillary data such as total column water vapor or emissivity. These algorithms are calibrated using a set of forward radiative transfer simulations that return the TOA radiances given the LST and the thermodynamic profiles. The simulations are done in order to cover a wide range of surface and atmospheric conditions and viewing geometries. This work analyses calibration strategies, considering some of the most critical factors that need to be taken into account when building a calibration dataset, covering the full dynamic range of relevant variables. A sensitivity analysis of split-windows and single channel algorithms revealed that selecting a set of atmospheric profiles that spans the full range of surface temperatures and total column water vapor combinations that are physically possible seems beneficial for the quality of the regression model. However, the calibration is extremely sensitive to the low-level structure of the atmosphere indicating that the presence of atmospheric boundary layer features such as temperature inversions or strong vertical gradients of thermodynamic properties may affect LST retrievals in a non-trivial way. This article describes the criteria established in the EUMETSAT Land Surface Analysis – Satellite Application Facility to calibrate its LST algorithms applied both for current and forthcoming sensors.

This study proposes parabolic dish-based toroidal structured fractal solar collectors. The potential of fractal geometry to increase heat transfer and the ability of the parabolic dish to concentrate solar rays form the basis of the proposed design for increasing the efficiency. In the study, the thermal and hydrodynamic behaviors of the proposed 3-row, 4-row and 5-row parabolic collectors were investigated comprehensively. Using theoretical modeling and experimental results, the performances of the proposed parabolic dish-based toroidal fractal solar collectors were evaluated and compared via numerical simulation methods. After the experimental studies of the 3-row toroidal fractal collector, the analysis studies were completed using the ANSYS-Fluent program. Then, simulations were carried out for other toroidal solar collectors using the results of these experimental studies. As a result of the converging numerical analyzes, the radiative, hydrodynamic and thermal analysis results of the toroidal absorbers in 3-row, 4-row and 5-row structures integrated with the parabolic dish were compared. In the temperature distribution analysis, it was observed that the parabolic dish effectively focuses on the sun rays and provides a gradual temperature increase of approximately 21 K for the fractal collector. It is observed that 96.84% convergence was achieved between the experimental and numerical results.

Tropical regions face unique challenges in building sustainability due to high temperatures, humidity, and heavy rainfall. While building energy regulations are essential for promoting energy efficiency, their effectiveness in addressing tropical climate conditions needs to be studied more. This research aims to systematically investigate tropical building sustainability issues and evaluate the impacts of building energy regulations on these challenges. The study will identify gaps in current regulations by analyzing existing research and recommend strategies for developing more comprehensive frameworks that promote sustainable building practices in tropical regions. This research contributes to developing effective policies and strategies for achieving sustainable and energy-efficient built environments in tropical climates.

The International Renewable Energy Agency (IRENA) was established in 2009 and in 2024, its membership increased to 168 members plus the European Union countries. The purpose of IRENA is to promote the adoption of renewable energy across all industries in the world. Despite the utilization of renewable energy in sectors like power generation and construction, its application in other industries remains limited. Therefore, a literature review study was conducted to investigate the cost and other spatial constraints associated with renewable energy resources, including modeling and optimization techniques that could offer viable solutions to the future challenges faced by the renewable energy production systems. This paper has summarized the result of this study with a focus on the significance of modeling and optimization techniques in energy conservation to highlight the untapped potential for leveraging renewable energy resources in industrial applications. This paper also examined a few case studies from various regions of the world, demonstrating the promising opportunities for research in the modeling and optimization of renewable energy management systems.

Building integrated photovoltaics (BIPV) consists of PV panels that are integrated into the building as part of the construction. This technology has advantages such as the production of electricity without necessary additional land area. This paper provides a literature review about the recent developments in urban building energy modelling, including tools and methods, and how they can be used to predict the effect of PV systems on building outdoor and indoor environments. It is also intended to provide a critical analysis on how PV systems affect the urban environment, both from an energy and a comfort point of view. The microclimate, namelly the urban heat island concept, is introduced and related with the existence of PV systems. It is concluded that urban building energy modelling (UBEM) can be effective to study the performance of PV systems in the urban environment. It allows to simultaneously predict the building energy performance and the microclimate effect. However, there is a need to develop new methodologies to overcome the challenges associated to UBEM, especially in what concerns non-geometric data, which leads to a major source of errors. and to find an effective method to predict the effect of PV systems in the urban environment.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

The benchmarking of hotel energy use comprehensively identifies the controllable and uncontrollable factors affecting energy performance, including building characteristics, management strategies, operations, and maintenance systems. Other factors include climatic conditions, floor areas, operating hours, occupancy rates, and guest populations. A benchmarking study on energy consumption patterns in significant hotels (each with less than 100 rooms and an average staff strength of 40 employees), situated in the university town of Nsukka (longitude 70 23' E, latitude 60 52' N), Nigeria, was performed using the data envelopment analysis (DEA) methodology. DEA, a linear programming technique that measures the relative performances of units, was chosen as a benchmarking methodology due to its ability to handle multiple inputs and outputs. Following a correlation test, energy use intensity, diesel consumption, and the number of employees were selected as the analysis inputs, while the occupancy rate was chosen as the output variable. Data on these variables spanning 12 months were collected using questionnaires, interviews, site visits, and oral conversations with hotel managers to ensure validity. Grid-supplied electricity accounted for most of the hotels' energy needs, followed by diesel used in generators. More than 70% of the electricity use was for HVAC. From the DEA, Hotel 3 (DMU H3) had a technical efficiency score of 1, whereas adjustments were recommended for improving the efficiency scores of the other hotels, which were deemed inefficient. DMU H7 had the lowest efficiency score (0.474) and the highest identified savings for electricity and diesel. The analysis also revealed that occupancy rates were generally low in the months of June and July, coinciding with the high rainfall season with its accompanying decline in outdoor activities. Consistent with this, electricity consumption was highest in the Christmas and Easter holiday months of December, January, and April following increased travel-related activities.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Wireless energy harvesting (EH) communication has long been considered a sustainable networking solution. However, it has been limited in efficiency, which has been a major obstacle. Recently, strategies such as energy relaying and borrowing have been explored to overcome these difficulties and provide long-range wireless sensor connectivity. In this article, we examine the reliability of the wireless-powered communication network by maximizing the net bit rate. To accomplish our goal, we focus on enhancing the performance of hybrid access points and information sources by optimizing their transmit power. Additionally, we aim to maximize the use of harvested energy by energy-harvesting relays for both information transmission and energy relaying. However, this optimization problem is complex as it involves non-convex variables and requires combinatorial relay selection indicators optimization for decode and forward (DF) relaying. To simplify this problem, we utilize the Markov decision process and deep reinforcement learning framework based on the deep deterministic policy gradient algorithm. This approach enables us to tackle this non-tractable problem, which conventional convex optimisation techniques would be difficult to solve in complex problem environments. The proposed algorithm significantly improves the end-to-end net bit rate of the smart energy borrowing and relaying EH system by 13.22%,27.57%, and 14.12% compared to the benchmark algorithm based on borrowing energy with an adaptive reward for Quadrature Phase Shift Keying, 8-PSK, and 16-Quadrature amplitude modulation schemes, respectively.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

The optimization of the energy grid is a critical task for ensuring a sustainable and efficient energy future. Deep machine learning techniques have the potential to improve energy grid optimization by predicting energy demands and supplies, optimizing energy production and distribution, and detecting and preventing fraud. However, there are also several challenges associated with the use of deep machine learning in energy grid optimization. These include the lack of standardized datasets and data quality issues, interpretability and explain-ability of machine learning models, ethical and social implications of using machine learning, and integration with existing energy infrastructure and regulatory frameworks. Having a clear understanding that continued research and developments in deep learning applications to energy field are crucial for achieving a sustainable and efficient energy future. This paper therefore reviewed existing literature for challenges and opportunities associated with deep machine learning in energy grid optimization; and highlights the importance of continued research and development in the field. The paper found out that opportunities for future research in deep machine learning for energy grid optimization include advancements in machine learning algorithms and techniques, development of new datasets and data collection methods, integration of machine learning with other emerging technologies. It also established needs for collaborative research and public-private partnerships.

We use a recently proposed formulation of quantum mechanics based, not on potential functions but rather, on orthogonal energy polynomials. In this context, the most important building block of a quantum mechanical system, which is the wavefunction at a given energy, is expressed as pointwise convergent series of square integrable functions in configuration space. The expansion coefficients of the series are orthogonal polynomials in the energy; they contain all physical information about the system. No reference is made at all to the usual potential function. We consider, in this new formulation, few representative problems at the level of undergraduate students who took at least two courses in quantum mechanics and are familiar with the basics of orthogonal polynomials. The objective is to demonstrate the viability of this formulation of quantum mechanics and its power in generating rich energy spectra illustrating the physical significance of these energy polynomials in the description of a quantum system. To assist students, partial solutions are given in an appendix as tables and figures.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

It is a truism that whole energy system models underpin the development of policies for energy system decarbonisation. But recent reviews have thrown doubt on the appropriateness of such models for addressing the multiple goals for future energy systems, in the face of emergent real-world complexity and the evolution of stakeholder’s priorities. Without an understanding of the changing priorities of policy makers and expectations of stakeholders for future systems, system objectives and constraints are likely to be ill-defined, and there is a risk that models may be inadvertently instrumentalised. Adopting a system architecture perspective, the authors have undertaken a three-year programme of research to explore strategies for decarbonising heat in the UK, with interaction with and elicitation of needs from stakeholders at its heart. This paper presents the procedure, methods, and results of an exercise in which experts from stakeholder organisations across the energy system were interviewed. Analysis of interview data reveals two broad approaches to heat decarbonisation which can be broadly defined as either adaptive or transformative. Specific insights gained from these interviews enabled our modelling teams to refocus their work for exploration with a wider circle of stakeholders. Results suggests that this iterative approach to formalising model-policy interaction could improve the transparency and legitimacy of modelling and enhance its impact on policy making.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

Airborne wind energy (AWE) systems use tethered flying devices to harvest higher-altitude winds to produce electricity. For a successful deployment of these systems, it is crucial to understand how the public perceives them. If public concerns about the technology are not taken seriously, implementation could be delayed or, in some cases, prevented, resulting in increased costs for project developers and a lower contribution of the sector to renewable energy targets. This literature review assessed the current state of knowledge on public responses to AWE. An exhaustive literature search led to the identification of 40 relevant publications that were reviewed. The literature assumed that the safety, visibility, acoustic emissions, ecological impacts, and the siting of AWE systems shape public responses to the technology. The reviewed literature views people’s responses to AWE very optimistically but lacks scientific evidence to back up its claims. It seems to overlook that the influence of AWE’s characteristics (e.g., visibility) on public responses will also depend on a range of situational and psychological factors (e.g., people’s general attitude towards AWE, the public’s trust in project developers). Therefore, empirical social scientific research is needed to increase the field’s understanding of public responses to AWE and thereby facilitate deployment.

Integration of battery energy storage in photovoltaic (PV) systems can reduce the electricity costs and provide desirable flexibility and reliability to these systems decreasing renewable energy fluctuations. This paper presents a review of the PV-battery application in Brazil, highlighting the challenges and prospects based on the state-of-art. A PV-battery systems description is presented in this work, as well as the most applied battery technology and its comparison. The paper also describes the set of applications such as voltage and frequency regulation, renewable energy integration, power quality, etc. In the Brazilian scenario, there are applications of PV-battery systems, most of them part of research and development projects (R&amp;D’s), and some real cases are shown, including its goals, applied equipment, operation modes, strategies, and perspectives. Additionally, this work evaluates the Brazilian scenario regarding the energy storage systems implementation challenges, such as regulatory barriers, business models, and opportunities for R&amp;D in the energy market. In conclusion, it is need develop proper regulatory models to expand PV-battery systems and make them visible to the agents in the electricity sector.