Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

Lombok earthquake that occurred in July 2018 has three large magnitude earthquakes that caused huge losses; 564 victims died, 1684 injured, 445 343 refugees, and 215 628 houses were damaged. The role of anesthesiology is very important to give prompt therapy for injured victims. This research gave an overview of the important role of Anesthesiologist and the selection of anesthesia techniques during the natural disasters’ victims’ management. This study was conducted by collecting data of all earthquake victims treated at the emergency room (ER) of RSUD NTB on August 6^th and 7^th 2018 and all victims operated during August 5 – 25^th 2018. All data were recorded, analyzed, and presented in descriptive form using frequency, pie chart, and bar diagrams. The result shown that the highest number of patients treated in ER are during the first seven days after the earthquake and reduced to several weeks. The majority of patients treated are trauma patients who need orthopedic surgery. Since limited number of anesthesiologist should be considered with the right selection of anesthesia techniques, so that the disaster preparedness could be prepared well and the disaster management could run well. General anesthesia was widely used than regional anesthesia, but the different is not significant. The type of regional anesthetic drug usually used is lidodex in combination with catapres. The role of anesthesiologist during disaster is important to handle a safe and optimal surgical condition.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

In this study, rheological properties of the bread wheat flour dough from 6 wheat genotypes were determined. For the pereparation of flour, 3 red bread (Pandas, Sagitorya, Pehlivan) and 3 white bread (Kaşifbey, Göktan, Ceyhan-99) were selected as wheat genotype. To determine the rheological properties of the wheat flour dough, farinograph, extensograph, mixolab and glutograph devices were used. According to the results of the Farinograph analysis, the average development time of wheat White and red genotypes were 1.95 minutes and 8.96 minutes, respectively. According to the extensograph results of the flour samples, the most extended stability value was determined with 7.47 min in Ceyhan-99 cultivar. As a result of the research, it was determined that flour yields of red bread varieties were higher other genotypes, gas retention capacities of white bread flours were showed high result in extensograph application and resistance of dough to elongation was higher. In the Mixolab analysis, it determined that white bread wheat varieties have higher values in terms of kneading properties and gluten properties, and red bread wheat varieties have higher values in values of viscosity, amylase value and starch retrogradation.

This study aimed to decrease the particle size of ginseng by roasting and cryogenic milling to increase its water solubility and physiological activity. The samples were roasted for different times (9–21 min) and generated in different sizes (10–50, and > 50 μm). All roasted samples revealed significantly smaller particle sizes than did non-roasted samples based on Sauter mean diameter (D [3,2], p < 0.05). Further, the particle sizes of roasted samples decreased till roasting up to 15 min. In terms of the water solubility index (WSI), antioxidant activity, total polyphenol content (TPC), and total polysaccharides according to particle size, 10-20 μm-sized samples showed the highest values when compared with >50 μm-sized samples. Based on roasting time, WSI values of all samples roasted for up to 15 min were higher than those of the control (not roasted) (p < 0.05). Antioxidant activity and TPC also increased with increasing roasting time. Total polysaccharide content was the highest upon roasting for 15 min except for the 10-20 μm sample. Ginsenoside content of roasted samples >20 μm size was higher than that of the control (not roasted) except after 15 min of roasting. Therefore, roasting and cryogenic milling are effective in producing ginseng root powder.

In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

Low back pain (LBP) is a pandemic and costly musculoskeletal condition in the United States. Patients with LBP may endure surgery, injections, and expensive visits to emergency departments. Some suggest that using physical therapy or chiropractic in the earlier stage of LBP reduces the utilization of expensive health services and lowers the treatment costs. Nevertheless, there is no consistent evidence to declare which one of these methods is a cost-effective treatment within a short (less than a year) period of time. The purpose of this study was to investigate the cost-effectiveness of chiropractic versus physical therapy in the United States. A decision tree analytic model was used for estimating the economic outcomes. The findings showed that in the chiropractic group, the total average cost was $48.56 lower than the physical therapy group, and daily adjusted life years (DALY) was 0.0043 higher than the physical therapy group. Chiropractic care was shown to be a cost-effective alternative compared with physical therapy for adults with at least three weeks of low back pain over six months.

A robust bank industry is a major player in the stability of an economy. The operational efficiency and stability of banks are therefore paramount. By way of financial ratios and Z-score, this study analysed UT Bank’s financial performance prior to the 2017 bank sector reforms in Ghana. Annual financials over a ten year period (2007-2016) were used. Debt management practices of UT Bank per the results obtained were quite on the hind side and unimpressive. This was reflected in the poor leverage and risk management variables. UT Bank would have been unable to meet creditors’ claims considering the mean average values of debt-to-assets and debt-to equity ratios of 0.76 and 0.90 respectively. The entire bank sector will benefit if credit management practices of individual banks are refreshed and worked on. The bank industry regulator should tighten its supervisory and monitoring role over banks to help detect early signs of non-performing banks. The study further recommends that statutory lending limits of banks be re-enforced to uphold the threshold of 10 percent for unsecured loans and 25 percentage for secured loans of net owned funds of the bank.

The known three-component reaction-diffusion system modeling competition and co-existence of different language speakers is under study. A modification of this system is proposed, which is examined by Lie symmetry method; furthermore exact solutions in the form of traveling fronts are constructed and their properties are identified. Plots of the traveling fronts are presented and the relevant interpretation describing the language shift occurred in Ukraine during the Soviet times is suggested

Glioblastoma (GBM) is the most lethal form of brain tumor, characterized by rapid growth and surrounding tissue invasion. The current standard treatment is surgery followed by radiotherapy, and concurrent chemotherapy, typically with temozolomide. Although extensive research has been performed over the past years to develop an effective therapeutic strategy for the treatment of GBM, efforts have not provided major improvements in the overall survival of patients with GBM. Thus, new therapeutic approaches are urgently needed. A major challenge in the development of therapies for central nervous system (CNS) disorders is overcoming the blood–brain barrier (BBB). In this context, the intranasal (IN) route of drug administration has been proposed as a non-invasive alternative route to directly targeting the CNS. In fact, this route of drug administration may bypass the blood-brain barrier and reduce systemic side effects. Recently, formulations have been developed to further enhance nose-to-brain transport, mainly with the use of nano-sized and nanostructured drug delivery systems. The focus of this review will be on the strategies developed to deliver a number of anticancer compounds for the treatment of GBM using the nasal administration. In particular, the specific properties of nanomedicines proposed for the nose-to-brain delivery will be critically evaluated. The number of preclinical and clinical data reviewed support the idea that nasal delivery of anticancer drugs might represent a breakthrough advancement in the fight against GBM.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

(-)-Zeylenone is a promising cytotoxic agent，which is a natural product isolated from Uvaria grandiflora Roxb. Though substantial antitumor mechanism has been researched , little has focused on its enantiomer (+)-Zeylenone.This article will try to find a gram scale synthesis method of (+)-Zeylenone and explain the structure-activity relationship of this kind of compound. Total synthesis of (+)-zeylenone was completed in 13 steps with quinic acid as starting material in 8.8% overall yield. The highlight of the route was the control of the three carbon’s chirality by clever use of single step dihydroxylation under the direction of the key C-3 chirality. In addition, zeylenone derivatives were designed and synthesized and their antitumor activity were evaluated against three human cancer cell lines using the CCK8 assay. Structure-activity relationship suggested compounds with both two absolute configurations exhibited good activity. Besides, hydroxyls at C-1/2 position were crucial for the activity and esterification of C-1 hydroxyl with large groups made the activity disappeared. Hydroxyl at C-3 position was also important as proper ester substituent could increase the potency.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

Research within the field of hydrology often focuses on comparing stochastic to machine learning (ML) forecasting methods. The comparisons performed are all based on case studies, while an extensive study aiming to provide generalized results on the subject is missing. Herein, we compare 11 stochastic and 9 ML methods regarding their multi-step ahead forecasting properties by conducting 12 large-scale computational experiments based on simulations. Each of these experiments uses 2 000 time series generated by linear stationary stochastic processes. We conduct each simulation experiment twice; the first time using time series of 100 values and the second time using time series of 300 values. Additionally, we conduct a real-world experiment using 405 mean annual river discharge time series of 100 values. We quantify the performance of the methods using 18 metrics. The results indicate that stochastic and ML methods perform equally well.

Exact and soliton type solutions have great importance in propagation of surface waves, fluid dynamics, optics, and many other elds of nonlinear sciences. In this study, the explicit and exact soliton type solutions for two space-time fractional Equal- Width (FEW) equations with conformable derivative are procured via the hyperbolic function approach. The wave type solutions are represented in some hyperbolic and trigonometric functions.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

Lichens are traditionally divided into short “crustose”, intermediate “foliose” and tall “fruticose” types, a practice that hides a growth continuum. Substrate, temperature and water are thought to affect vertical growth, but such factors are difficult to measure, because, for example, the water actually available to lichens does not match rainfall patterns or even ground water levels. To reliably assess the effect of those factors, I recorded temperature, moisture, and substrate in and under individual terricolous lichen colonies in 60 fixed quadrats on April, August, October, and December of 2015 (Cerro de la Muerte, Costa Rica, 9°33′N; 83°45′W). The measurements were taken inside the colonies themselves (rather than on the general environment), covering an annual cycle of the relatively simple páramo habitat, where animals and vegetation have less impact than in lower ecosystems. The hypotheses were that lichens would grow taller on softer, warmer, and moister ground; on the Caribbean versant; and on the rainy season. Results matched the hypotheses, with one exception: lichens on soft ground were not taller than those on rock. Caribbean colonies were, on the average, 7 cm taller than those on the drier Pacific versant. Physiologically available water seems to be the main determinant of lichen vertical growth: more water means taller lichens and greater protection from climatic change for both the lichens and their microcommunities.

Zinc is mostly extracted from zinc oxide and sulfide minerals, and this process involves flotation as a key step. While it is easier to float the sulfide mineral, its consumption and depletion has led to an increased reliance on zinc oxide minerals, including smithsonite; hence the development of efficient ways of collecting smithsonite by flotation is an important objective. Herein, we describe the use of 2-(hexadecanoylamino)acetic acid (HAA), a novel surfactant, as a collector during smithsonite flotation. The mechanism and flotation performance of HAA during smithsonite flotation were investigated by total organic carbon (TOC) content studies, zeta potential measurements, FTIR spectroscopy, and XPS analyses, combined with micro-flotation experiments. The flotation results revealed that HAA is an excellent collector in pulp over a wide pH range (9–12) and at a relatively low concentration (2 × 10^‒4 mol/L), at which a recovery of close to 90% of the smithsonite mineral was obtained. TOC-content studies reveal that the good flotation recovery is ascribable to large amounts of collector molecule adsorbed on the smithsonite surface, while zeta potential measurements show that the HAA is chemically adsorbed onto the smithsonite. FTIR and XPS analyses reveal that the HAA-collector molecules adsorb onto the smithsonite surface as zinc-HAA complexes involving carboxylate moieties and Zn sites on the smithsonite surface in alkaline solution.

A formulation of nonequilibrium thermo field dynamics has been performed using the nonequilibrium statistical operator method by D.N. Zubarev. Generalized transfer equations for a consistent description of kinetics and hydrodynamics of the dense quantum-field system with strongly coupled states are derived.

In recent years, biomedical research has faced increased scrutiny over issues related to reproducibility and quality in scientific findings(1-3). In response to this scrutiny, funding institutions and journals have implemented top-down policies for grant and manuscript review. While a positive step forward, the long-term merit of these policies is questionable given their emphasis on completing a check-list of items instead of a fundamental re-assessment of how scientific investigation is conducted. Moreover, the top-down style of management used to institute these policies can be argued as being ineffective in engaging the scientific workforce to act upon these issues. To meet current and future biomedical needs, new investigative methods that emphasize collective-thinking, teamwork, shared knowledge and cultivate change from the bottom-up are warranted. Here, a perspective on a new approach to biomedical investigation within the individual laboratory that emphasizes collaboration and quality is discussed.

Minerals might have played critical roles for the origin and evolution of possible life forms on Mars. The study of the interactions between “building blocks of life” and minerals relevant to Mars mineralogy under conditions mimicking the harsh Martian environment may provide key insight into possible prebiotic processes. Therefore, this contribution aims at reviewing the most important investigations carried out so far about the catalytic/protective properties of Martian minerals toward molecular biosignatures under Martian-like conditions. Overall, it turns out that the fate of molecular biosignatures on Mars depends on a delicate balance between multiple preservation and degradation mechanisms often regulated by minerals, which may take place simultaneously. Such a complexity requires more efforts in simulating realistically the Martian environment in order to better inspect plausible prebiotic pathways and shed light on the nature of the organic compounds detected both in meteorites and on the surface of Mars through in situ analysis.

The alignment of nanostructures in materials such as lyotropic liquid crystals (LLCs) templated materials has the potential to signicantly improve their performances. However, accurately characterising and quantifying the alignement of such fine structures remains very challenging. In situ small angle X-ray scattering (SAXS) and molecular dynamics were employed for the first time to understand the hexagonal LLC alignment process with magnetic nanoparticles under a magnetic field. The enhanced alignment has been illustrated from the distribution of azimuthal intensity in the samples exposed to magnetic field. Molecular dynamics simulations reveal the relationship between the imposed force of the magenetic nanoparticles under magnetic field and the force transferred to the LLC cylinders which leads to the LLC alignment. The combinational study with experimental measurement and computational simulation will enable the development and control of nanostructures in novel materials for various applications.

This study was designed to assess variation of possible phytochemical compounds in the ethanolic extracts of Gigantochloa scortechinii rhizome. Destructive sampling was done by using selective random sampling method on four consecutive rhizomes from healthy clumps and was conducted at two natural forests and one secondary forest (planted). Homogenized sample were extracted using solvent extraction (70% ethanol) method. Ethanolic extracts of G. scortechinii rhizome were qualitatively analyzed using GC/MS GC2010 Plus, Shimadzu to determine the composition of phytochemical compounds and identified using FFNSC 1.3, NIST11, PMW_tox2, and Wiley229 spectral library. A qualitative variation was observed with a total of 56 compounds were identified and differentiated between study site and rhizome age. Results revealed that G. scortechinii rhizome contains various phytochemical compounds with potential as a plant of phytopharmaceutical importance. This is the first finding on the spatial and age-related effects of phytochemical compounds in a consecutive rhizome and of G. scortechinii rhizome specifically.

Overexpression of a constitutively active truncated form of OsCDPK1 (OEtr) in rice produced smaller seeds, but a double-stranded RNA gene-silenced form of OsCDPK1 (Ri) yielded large seeds, suggesting that OsCDPK1 plays a functional role in rice seed development. In the study presented here, we propose a model in which OsCDPK1 plays key roles in negatively controlling the grain size, amylose content, and endosperm appearance, and also affects the physicochemical properties of the starch. The dehulled transgenic OEtr grains were smaller than the dehulled wild-type grains, and the OEtr endosperm was opaque and had a low amylose content and numerous small loosely packed polyhedral starch granules. However, the OEtr grain sizes and endosperm appearances were not affected by the temperature being either optimal (25 °C ) or low (22 °C) or high (31 °C) during the grain-filling phase. In contrast, the transgenic Ri grains were larger, had higher amylose contents, and had more transparent endosperms filled with tightly packed polyhedral starch granules. This demonstrates that OsCDPK1 plays a novel functional role in starch biosynthesis during seed development and affects the transparent appearance of the endosperm. These results improve our understanding of the molecular mechanisms through which the grain filling process occurs in rice.

This article aims to serve as a guide for the construction of supply chain simulation models designed with a lean approach, using Promodel software. To achieve this, a supply chain was designed for a fictitious company located in the City of Celaya, Guanajuato and a set of suppliers located in different cities within the same State. It was used as a google tool to define the distances between each of the companies. As a final result, a representative model of a supply chain was obtained, as well as a methodology that allows the construction of lean supply chains regardless of the number of companies that comprise it. The effect of the variability in the delivery times between suppliers was incorporated into the simulation model, as well as an equation that calculates the pollution emissions of the vehicles that integrate the network that moves the products between the companies. With this work it is possible to represent networks of supply chains of real world companies, where the variability and contamination factor is included, to facilitate the decision making regarding the number of vehicles, inventory levels, quantities to be shipped, frequency in the shipments, etc. with the purpose of contaminating as little as possible and at the same time preventing interruptions in the supply chain using the least amount of resources possible.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

In a global context, the story of the Jesuit compound in Shanghai, since its establishment by French Jesuits in 1847, reflected not only conflicts between rival powers in Europe but also the fight for their interests in the Eastern world. The Pope, who was stuck without legal status in the Vatican after 1861, was also seeking the chance to save the authority of the Church in the face of questions regarding the extent of his temporal power and the status of Rome in the context of Italian unification. As in the Reformation, a break-through in the east seemed to offer a solution for losses in Europe. However, the Jesuits to the East in the late 19th century were not only troops working and fighting on behalf of the Pope; their identities under the French Protectorate added complexity to an already complicated story involving not just the Church, but the course of world history.The female Catholic orders at the east bank of Zi-ka-wei compound became a unique window to approach the complexity.

Bread wheat (Triticum aestivum L.) is staple of Pakistani people. However, its yield at farmer field is low as compared with its genetic potential. Integration of various crop and soil management strategies might be an option to enhance wheat productivity at farmer field. This 2-year experiment was conducted to check the influence of combine application of natural plant water extracts and biochar on the productvity of wheat during the winter season of 2015-16. The experiment consisted of seven treatment viz. (1) control (2) application of biochar (0.18 kg pot-1) alone, (3) application of sorghum water extract (SWE) alone, (4) application of moringa water extract (MWE) alone, (5) application of biochar + SWE, (6) application of biochar + MWE, (7) application of biochar + SWE+MWE. The results revealed that application of both crop water extracts in combination with biochar improved the growth and grain yield of wheat. Use of MWE in combination with biochar enhanced the grain weight, grain number and grain yield of wheat by 44, 14, and 24%, respectively than the control treatment. In crux, use of MWE in combination with biochar might be a viable option to improve the productivity of bread wheat.

In sub-Saharan Africa (SSA), cervical cancer is a critical public health issue; it is the second leading cause of cancer among women and the leading cause of female cancer deaths. Incidence and mortality rates are substantially higher than in high-income countries with population-based screening programs, yet implementing screening programs in SSA has so far proven to be challenging due to financial, logistical and sociocultural factors. Human Papillomavirus (HPV) vaccination is an effective approach for primary prevention of cervical cancer and presents an opportunity to reduce the burden from cervical cancer in SSA. With a number of SSA countries now eligible for GAVI support for vaccine introduction, it is timely to consider the factors that impede and facilitate implementation of vaccine programs in SSA. This article reviews the epidemiological and clinical features of cervical cancer in SSA and describes the current status of HPV vaccine implementation in SSA countries. The review considers the challenges that will need to be addressed, and effective approaches to the design and implementation of HPV vaccination programs, using Rwanda as a case study. The review aims to provide suggestions and guidance to those involved in the development and implementation of HPV vaccination programs in SSA.

While obesity is a serious chronic condition, its prevalence and documentation as a diagnosis has not been extensively studied in hospitalized patients. We conducted a retrospective chart review to investigate the prevalence and documentation of obesity as a diagnosis among patients admitted to our medical center. IRB approval was obtained for this retrospective study. Body mass index as per CDC, admission and discharge diagnosis of obesity and common comorbidities including hypertension, diabetes, hyperlipidemia and others, were recorded. Length of hospital stay was calculated. We also investigated whether counselling for weight loss was provided to obese patients. A total of 540 consecutive patients with mean age of 66 ± 6 years, were investigated, of which 182(34%) had normal weight, 188(35%) patients were overweight and 170(31%) patients were obese. Obese group included 55% female and 45% male. 100 (59%) had class I obesity, 43(25%) had class II obesity and 27(16%) class III obesity. Of the obese patients 40/170(23.5%) patients had obesity documented on the admission problem list and only 21(12%) had obesity documented as a discharge diagnosis. Only 3(2%) patients received appropriate counseling and referral for obesity management during the hospitalization. Comorbidities included hypertension (68%), diabetes (35%), hyperlipidemia (36%), coronary artery disease (18%), chronic kidney disease (17%), congestive heart failure (18%) and COPD (24%). The average length of stay in normal weight, overweight and obese patients was similar (4.5 ± 0.5 days). An overwhelming percentage never had weight status documented despite significant prevalence of obesity. Hospitalization offers health care providers a window of opportunity to identify obesity, communicate risks and initiate weight management interventions.

In Africa, 80% of households in urban areas are food insecure and is coupled with a dramatically changing urban food culture towards increased consumption of sugary and fatty foods. Consequently, incidences of obesity and undernourishment in many African cities are becoming escalating. Urban and peri-urban forestry emerges as a complementary measure to contribute towards elimination of urban hunger and improved nutritional security. However, there is scanty knowledge about the composition, diversity and socioeconomic contributions of urban food trees in African cities and this hinders policy discussions integrating urban forestry into the food security discourse. This paper examines the diversity and composition of the urban forest and food trees of Accra and sheds light on perceptions of urbanites regarding food tree cultivation and availability in the city. Using a mixed methods approach, about 105 respondents in six neighbourhoods of Accra were interviewed while over 200 100-m2 plots were surveyed across five land use types. Twenty-two out of the 70 woody species in Accra are edible. The food tree abundance in the city is about half of the total number of trees enumerated. The species richness and abundance of the edible trees and all trees in the city were significantly different among land use types (p<0.0001) and neighbourhood types (p<0.0001). The diversity of food bearing tree species was much higher in the poorer neighbourhoods than in the wealthier neighbourhoods. Respondents in wealthier neighbourhoods indicated that tree and fruit tree cover of the city was generally low and showed greater interests in cultivating fruit trees and expanding urban forest cover than poorer neighbourhoods. These findings demonstrate the need for urban food policy reforms that integrate urban grown tree foods in the urban food system/culture.

The increase in the emission of greenhouse gases (GHG) is one of the most important world problems. Decreasing of GHG emission is a big challenge in the future. Transportation sector uses a significant part of petroleum production in the world and it leads to an increase in the emission of GHG. The result of this issue is that population of the world befoul environment of transportation system automatically. Electric Vehicles (EV) have a potentiality to solve a big part of the GHG emission and energy efficiency issues such as stability and reality of energy. The energy actors and their research team determine some targets for 2050; hence, they hope to decrease the world temperature to 6 °C in the best and 2 °C in the normal condition. Fulfillment of these scenarios needs suitable grid infrastructure but in most of the countries, the grid does not have a suitable background to apply those scenarios. In this paper, some problems about energy scenarios, energy storage systems, grid infrastructure and communication systems in supply and demand side of the grid and its solutions have been investigated.

Nanoparticles (NPs) are widely used in diverse disciplines, including biology, medicine science. The central question that need to be answered is whether NPs have toxic effects on biological cells and molecules or are they safe. The safety of NPs including targeted drug delivery is critical and so is their toxicity in the environment. In recent years, in vitro and in vivo research on animals has generated abundant information about the toxicity of NPs. However, due to varying laboratory conditions, the comparison of the results from ensuing studies is somewhat unreliable. It should be noted that, depending on the type of production, NPs can enter the body through inhalation, skin and via digestive routes. Due to the diversity of NPs and their properties, there is paucity of accurate information on their toxicological effects; particle size, shape, surface area and the chemical levels are considered as key factors in creating health and toxicological effects. Consequently, there is a need for reliable information about their effects on various organs so as to deal with NPs effectively and their impact on health and the environment. This review covers the existing knowledge base on the subject that hopefully prepares us better to address these challenges.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

Extensive phytochemical and chromatographic analysis of different root fractions of Jatropha pelargoniifolia Courb. (Euphorbiaceae) resulted in the isolation and identification of 22 distinct secondary metabolite compounds. Two new compounds, 6-hydroxy-8-methoxycoumarin-7-O-β-D-glycopyranoside and (3-(2-(methylamino) ethyl)-1H-indol-2-yl) methanol, were isolated and identified for the first time from a natural source. In addition, other known compounds, such as hovetricoside C and N-methyltryptamine were isolated from Euphorbiaceae, and hordenine, N-methyltyramine, their salts, cynaroside and linarin were identified in Jatropha spp. for the first time. Some isolated metabolites, such as β-sitosterol, β-sitosterol glucoside, curcusons D and C, naringenin, apigenin, cleomiscosins B and A, spruceanol, propacin, jatrophadiketone, and uracil were previously identified in various Jatropha species. The structures of the isolated compounds were determined using different spectroscopic techniques. The anti-inflammatory, antinociceptive, antipyretic, and antioxidant activities were evaluated for some adequately available isolated compounds. Compounds showed significant antinociceptive activity compared with the standard analgesic drug indomethacin. The edema size was significantly reduced (p< 0.05–0.001) in the animals treated with low doses (5 and 10 mg/kg) of the isolated compounds compared with those treated with a high dose (100 mg/kg) of standard anti-inflammatory drug (phenylbutazone). Furthermore, all tested compounds showed a significant (p< 0.05–0.001) reduction in the rectal temperature of hyper-thermic mice.

Background: Ultrasound measurement of dynamic changes in inferior vena cava (IVC) diameter and collapsibility index (CI) evaluates to estimate the fluid responsiveness and intravascular volume status. We conducted a analysis to quantify the sonographic measurement of IVC diameter changes in adult patients at preoperative and postoperative period. Methods: Ultrasonography was performed on 72 patients scheduled for surgery with American Society of Anesthesiologists physical status I to III. Quantitative assessments of the end-expiration (D_min), end-inspiration (D_max) and CI at preoperative and postoperative period were compared in a prospective, observational study. The patients received intravenous fluid according to standard protocol regimes peroperatively. The cutt-off value of dIVC 40% was accepted as hypovolemia. Results: Ultrasonography of IVC measurement was unsuccessful in 12.5% of patients and 63 patients remained for analyses. The mean age was 43.29 ± 17.22 (range 18 - 86) years. The average diameter of the D_min, D_max and dIVC at preoperative and postoperative were 1.99 ± 0.31 vs. 2.05 ± 0.29 cm, 1.72 ± 0.33 vs. 1.74 ± 0.32 cm, 14.0 ± 9.60 % vs. 15.14 ± 11.18 %, respectively (p<0.05). Using a threshold dIVC of 40%, one patient preoperatively and 5 postoperatively were hypovolemic (p<0.05). CI was also positively associated preoperatively and postoperatively (regression coefficient = 0.438, p<0.01). Conclusion: The diameter of IVC did not change preoperatively and postoperatively in adult patients with standard fluid regimens. The parameters of the IVC diameter increased postoperatively according to preoperative period.

The “Crisis of Reproducibility” has received considerable attention both within the scientific community and without. While factors associated with scientific culture and practical practice are most often invoked, I propose that the Crisis of Reproducibility is ultimately a failure of generalization with a fundamental scientific basis in the methods used for biomedical research. The Denominator Problem describes how limitations intrinsic to the two primary approaches of biomedical research, clinical studies and pre-clinical experimental biology, lead to an inability to effectively characterize the full extent of biological heterogeneity, which compromises the task of generalizing acquired knowledge. Drawing on the example of the unifying role of theory in the physical sciences, I propose that multi-scale mathematical and dynamic computational models, when mapped to the modular structure of biological systems, can serve a unifying role as formal representations of what is conserved and similar from one biological context to another. This ability to explicitly describe the generation of heterogeneity from similarity addresses the Denominator Problem and provides a scientific response to the Crisis of Reproducibility.

Clinical training in medical schools in Spain is performed by rotations in university hospitals. During these internships, students are expected to acquire and master basic procedural skills. However, the assessment tools available rarely check whether these skills are completely acquired by the students. We have used an e-portfolio to determine the optimal number of times the students need to repeat a procedure to be able to perform it independently. The results were compared with the actual performance during the internships. An e-portfolio collected qualitative information about the internships. Quantitative information was also requested about the number of times each clinical skill was performed. Later, a survey asked these students and their teachers the optimal number of times each skill should be repeated before it could be considered fully acquired. The questionnaire was answered by 98.6% of the students and 70.3% of their teachers. Out of the 21 clinical skills and procedures selected, both students and their tutors agreed in a similar optimal value in 16 of them; only in five of them, teachers thought that students needed a greater number of times than that selected by the students. When these optimal values were compared with the actual values recorded in the portfolio during the internships, it was found that about half of the clinical skills were carried out less frequently than expected, thus providing an important feedback about the internships. Quantitative information collected in portfolios reveals a moderate mismatch between students and tutors perceptions of their training needs.

The wide range of applications of nanoparticles (NPs) has increased the probability of environmental and occupational exposure. In a previous comparative study on cell line A549, we observed that oxidative stress caused by Co₃O₄ NPs affects the energetic homeostasis and the detoxification capacity, preventing autophagy induced by TiO₂ NPs. In this study, we have investigated the effects of NPs on the cell cycle.Cytofluorimetric analysis showed a slow-down of the cell cycle progression for both NPs, with increases in the percentage of resting cells in the G0/G1. These observations were confirmed by a reduced expression of all cyclins, especially of CCNE1 and CDK2, involved in the late stages of the G1 phase, coupled with a significant increase in the expression of p21 only for Co₃O₄ NP exposure. On the contrary, the effects of TiO₂ NPs were modest. Cell cycle related miRNA-34a, miRNA-126 and miRNA-1290 resulted increased at different early time-points (4-8h) but were down-expressed at 24h-48h only after TiO₂ NP exposure. Our results show that NPs have an antiproliferative effect and deregulate cell cycle on A549 cells. These effects should not be underestimated because regulation of cycle progression is crucial for cell survival and repair of genetic damage.

In the international scenario of agriculture, Brazil stands out as the main producer and consumer of common bean (Phaseolus vulgaris L.) The increase in the productive potential of the crop is mainly due to breeding programs. The objective of this study was to estimate genetic parameters, predict genotypic values with REML/BLUP (Restricted Maximum Likelihood/Best Linear Unbiased Prediction) and, based on these values, study the variability in common bean cultivars with carioca and black grain. Twenty three agromorphological descriptors were evaluated, among them grain yield. Deviance analysis detected significant differences between the cultivars in both groups. Selective accuracy (Ac) was considered high for most of the traits. Broad-sense heritability (h_g² ) ranged from 0.05 to 0.72, but it was low for the trait yield (YLD). In the carioca grain group, the h_g² values for the traits related to plant morphology were higher than in the black group. Nevertheless, the h_g² values in the black group were higher in relation to the pod and seed traits. The correlations for YLD were moderate but different in the two commercial groups studied. In the black group, variables related to the seed morphology were correlated with grain yield, and in the carioca group, traits related to seed quantity. Based on the groupings, variability among the cultivars was observed. Three distinct clusters were formed for the carioca group and four for the black group. Based on the predicted genetic values, genetic variability and the most adapted and stable cultivars were detected among the cultivars in the studied environments.

We present a numerical study in which large-scale bulk simulations of self-assembled DNA constructs have been carried out with a realistic coarse-grained model. The investigation aims at obtaining a precise, albeit numerically demanding, estimate of the free energy for such systems. We then, in turn, use these accurate results to validate a recently proposed theoretical approach that builds on a liquid-state theory, the Wertheim theory, to compute the phase diagram of all-DNA fluids. This hybrid theoretical/numerical approach, based on the lowest order virial expansion and a nearest-neighbor DNA model, can provide, in an undemanding way, a thermodynamic description of DNA associating fluids that is in semi-quantitative agreement with experiments. We show that the predictions of such scheme are as accurate as the ones obtained with more sophisticated methods. We also demonstrate the flexibility of the approach by incorporating non-trivial additional contributions that go beyond the nearest-neighbor model to compute the DNA hybridization free energy.

The rapid urbanization has exerted tremendous pressure on natural systems in mountains. As a measure of sustainable use of natural resources, ecological footprint is an important basis for judging whether the development of a country or region is within the biocapacity. Taking Dali Bai Autonomous Prefecture as an example, this study comprehensively analyzes the impact of human activities on mountain resources and environment from the three aspects of urbanization, land use and ecological carrying capacity. The results show that Dali Prefecture with the urbanization rate of 33% is still in the accelerated stage of urbanization. The urban space presents the core-periphery feature, and the central city is the focus of human existence and living activities. The per capita ecological footprint is 1.14 hm2/person higher than the ecological carrying capacity, meaning Dali Prefecture is in an ecological deficit state. This indicates that there is an uncoordinated state between urbanization and environment. Arable land is the main source of per capita ecological footprint in the prefecture. However, the urban expansion overly occupies the arable land in the plain sub-region, leading the arable land to an ecological deficit state. In the future, the development of the mountainous area should focus on the protection of arable land and choose a new sustainable path.

Plants are an important feature of urban ecosystems which provide numerous environmental and ecosystem benefits such as defenses against noise and air pollution and conservation of biodiversity. The aim of this study was to investigate the structure and composition of urban vegetation in different urban habitats like roadsides, parks, gardens and playgrounds in Dhaka South City area. Stratified random sampling method was used in this study. A total of 221 plant species belonging to 63 families were identified and recorded. Among all plant species Swietenia macrophylla, Polyalthia longifolia, Cocos nucifera, Samanea saman, and Artocarpus heterophyllus are recorded as the most dominant. Most of the tree and shrub population were found between 6-9 m and 1-3m height classes whereas most of tree and shrub population were found in between 10-15cm dbh classes. Highest IVI was found for Swietenia macrophylla (193.22%) followed by Polyalthia longifolia (184.59%), Samanea saman (138.37%), Cocos nucifera (79.9%) and Delonix regia (68.27%) respectively. Average frequency, density, dbh and basal area were found 46.82%, 138.28 tree ha^-1, 458.59 cm ha^-1 and 12.33 m² ha^-1 respectively. Findings of this study reveals that structural attributes of plant represent quite young and still developing vegetation. This research will help to plan for future green infrastructure which will maintain ecosystem function, therefore, providing longer term benefits for the city dwellers.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

Bayesian analysis for masked data under competing risk frameworks is studied for the purpose of assessing the impact of covariates on the hazard functions when the failure time is exactly observed for some subjects but only known to lie in an interval of time for the remaining subjects. Such data, known as partly interval-censored data, usually result from periodic inspection. Dirichlet and Gamma processes are assumed as priors for masking probabilities and baseline hazards. The Markov Chain Monte Carlo (MCMC) technique is employed for the implementation of the Bayesian approach. The effectiveness of the proposed model is tested through numerical studies, including simulated and real data sets.

Western Iran barb species are scientifically, environmentally, and economically important. Some of them are the largest riverine freshwater species, which will grow in size and weight to 170 cm, and 120 kg respectively. Although these species are vulnerable, there is little information on taxonomy or environmental status of the species Luciobarbus barbulus is one of the important large species. In order to find the new record on the present status of large barb species sampling program carried out in western Iran, during the resent year since 2013 to now. This species overlaps in distinction with L. mystaceus, L scheich, and other similar species. In this study re-description of L.barbulus is given. This species differs from L. mystaceus in having thick and very wide fleshy lip, inferior mouth and slightly shorter head. In Luciobarbus barbulus head is more inferior. The details of differences between these species are given. This species is one of stable growing fish without dimorphism, retain its shape from a fingerling species to a giant fish.

The County of Avon in England was abolished in 1996 and replaced by four unitary planning authorities. Recently the authorities have been working closely to develop a West of England Joint Spatial Plan to facilitate better integration of policies on transport, housing, the environment etc. The Joint Spatial Plan team commissioned a multidisciplinary study to investigate whether the West of England has special characteristics of 'place' that engender shared interest and regional affinity, i.e. ‘sense of place’, to which emerging planning policies might positively respond. In this regard the present article is particularly focused on identifying whether the West of England has unique and unifying landscape characteristics, relating to topography, rural scenery, and flora and fauna, which combine with human experiences to distinguish the Region from adjoining areas. It is concluded that the West of England does indeed have real geographical integrity, being bound on all sides by attractive and prominent landscape features - the Mendip Hills, Cotswold Hills and Severn Estuary – that contribute to a sense of identity and belonging among its inhabitants. The alternating limestone ridges and broad clay vales that prevail across the Region’s heart, combined with low lying flatlands on the Region’s western fringe, provide further contrast with neighbouring regions, reinforcing the emotional bond to the landscape. Furthermore, it is suggested that the inhabitants of the West England show a particularly special environmental consciousness that sets them apart from neighbouring populations, complementing the influence of the physical environment in making the Region a special place to live.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Lack of water resources in Iran, especially in recent years, has faced the agricultural sector as the most important consumer of water resources, with serious challenges. In Iran, the agricultural sector accounted for more than 90% of water consumption. However, the focus on domestic production and self-sufficiency policy in staples (wheat, barley, maize and rice) has been emphasized in general agriculture's policy. This study was conducted to estimate the imported virtual water from the imports of basic products in Iran using defined indicators during 1961-2013. Also this study investigated the possibility of achieving self-sufficiency due to the limited water resources in Iran. The results of this study showed with the increase in cereal imports, virtual water imports from 0.28 billion cubic meters in 1961 increased to 17.6 billion cubic meters in 2013 and on average about 60% of virtual water imports in strategic products is related to wheat imports during the past 53 years. Other products in cereal (barley, maize and rice) are also indicative of the general trend of increasing imports of virtual water in development plans. The estimated long-run elasticity of virtual water imports in the cereal group compared with the country's water resources also showed that with a one percent reduction in renewable water resources of the country, the virtual water import in the main cereal group will increase equivalent to 2.89 percent and the determination coefficient more than 90 percent also confirms this negative relationship. According to this result and the emphasis on the fact that renewable water resources per capita in the country is falling increasingly, it cannot be expected that domestic production could compensate for the imports of the cereal group and virtual water imports with current technology, without increasing the water productivity and without additional harm to water resources.

Solanum nigrum fruits have been conventionally available as a material of beverage due to its nutritional substances such as minerals, vitamins, amino acids, proteins, sugars, polyphenols and anthocyanins. Here has rarely reported on the characterizaton of the components and the regulatory mechanism of Anthocyanins in S. nigrum. In this study, we determined that the peel and flesh of S. nigrum fruits shared the similar HPLC profiles, but the different contents and total antioxidant activities for Anthocyanins. After an efficient purification method mainly including extraction with pH 1.0 distilled water and then desorption with pH 1.0 95% ethanol after a DM-130 resin adsorption step to obtain more pure anthocyanins extracts, the purity of anthocyanins extract from S. nigrum fruits reached to 56.1%. Moreover, eight anthocyanins from S. nigrum fruit were identified with HPLC-MS/MS for the first time. A typical R2R3-MYB transcription factor gene, SnMYB, was also cloned for the first time by RACE-PCR from S. nigrum. Moreover, the contents of anthocyanins was shown a good correlation (r = 0.93) with the expression levels of SnMYB during the fruits developmental stages. Most significantly, SnMYB successfully produced high anthocyanins contents (1.03 mg/g) when SnMYB was transiently expressed in tobacco leaves. Taken together, S. nigrum fruits are a promising resource for anthocyanins extraction and SnMYB is an activator that positively regulates anthocyanins biosynthesis in S. nigrum.

Carbon nanotube (CNT) yarns are fiber-like materials that exhibit excellent mechanical, electrical and thermal properties. More importantly, they exhibit a piezoresistive response that can be tapped for sensing purposes. The objective of this study is to determine experimentally the piezoresistive response of CNT yarns that are embedded in a polymeric medium while subjected to either compression or tension, and compare it with that of the free or unconstrained CNT yarns. The rationale for this study is the need to know the response of the CNT yarn while in a medium, which provides a lateral constraint to the CNT yarn thus mimicking the response of integrated CNT yarn sensors. The experimental program will include the fabrication of samples and their electromechanical characterization. The CNT yarns are integrated in polymeric beams and subjected to four-point bending, allowing the determination of their response under tension and compression. The electrical resistance data from an Inductance-Capacitance-Resistance (LCR) device is used with the data acquired from the mechanical testing system to determine the piezoresistive response of the CNT yarns. This data and information will be used for future modeling efforts and to study the phenomena that occur when CNT yarns are integrated in polymeric and composite materials and structures.

Quantum Computers are provisioned as very high performance computers using quantum mechanical aspects for information processing. Quantum Information Theory and Quantum Computing topics are popular topics in academia aiming the construction of theoretical background of Quantum Computers. The information processing units for Quantum Computers are defined as qubits but for some problems three level (trinary) systems may be applied as well. We call these three level systems as qutrits. The scope of this work is the analysis of well-defined entanglement measures Negativity and Relative Entropy of Entanglement (REE) for two qutrit (3- level/trinary) quantum systems. In this manner, for randomly generated 1000 two qutrit and 1000 two qubit states the mentioned measures are calculated and these values are compared. These comparisons are analyzed and for quantum state ordering problem, some interesting results are reported.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

There is a need for alternatives or complements to synthetic fertilizers to enhance agricultural sustainability. Applying organic amendments can play a significant role in this. Insect droppings show high potential, though studies evaluating their agronomic value have only recently begun to emerge. This study compared black soldier fly (Hermetia illucens) and mealworm (Tenebrio molitor) larvae frass with another organic amendment (Nutrimais) derived from composting forestry, agro-industrial, and domestic waste. The experiment also included ammonium nitrate at two rates [the same as the organic amendments, 50 kg ha–1 nitrogen (N) (FullR), and half that rate (HalfR)] and an unfertilized control. The study spanned two growth cycles of lettuce (Lactuca sativa L.) grown in pots, followed by unfertilized oats (Avena sativa L.) to assess the residual effects of the fertilizing treatments. Mealworm larvae frass mineralized rapidly, with an apparent N recovery of 37.4% over the two lettuce growth cycles, indicating its high availability to soil heterotrophic microorganisms. The average dry matter yield (DMY) of lettuce was the highest among all treatments (12.8 and 9.8 g plant–1 in the first and second lettuce cycles), even compared to the FullR treatment (12.2 and 7.8 g plant–1), though without significant differences. Although mealworm larvae frass exhibited a high mineralization rate, the DMY cannot be attributed solely to N supply, as plants in the FullR treatment showed better N nutritional status. Mealworm larvae frass provided strong evidence of a plant biostimulant effect, not explained by the variables measured in this study. Black soldier fly larvae frass exhibited typical behavior of a moderately reactive organic amendment, while Nutrimais showed low reactivity, with a near-neutral mineralization/immobilization balance. The results suggest mealworm larvae frass is recommended for early maturing vegetable crops, whereas Nutrimais appears more suitable for perennial crops with low short-term nutrient requirements.

The administration and management of urban transport has become an urgent need, in the context of the increasing congestion problems and the environmental and economic damage, resulting from rapid urban expansion witnessed by the Algerian cities in recent times, in order to achieve prosperity and quality of urban life. It became necessary to use the tools of modern technology, which administrative and technical departments are seeking to use primarily to support ways of decision-making and actions required. Boosted by high capabilities in the statistical data and other information is stored, and coordination and tabulation, with the possibility of installation and analysis by operations. Especially against the inability of traditional methods, which have become less able to cope with the changes that led to the urban dynamic currently experienced by urban communities in our country. This research aims to employ geographic information systems in the administration and management of the urban transport network, facing both the population and the local administration of the city of Batna. Which was chosen as a model for major Algerian cities, which is suffering more than ever of transportation bottlenecks, as well as the unintended damage for these networks and other networks. Hence the importance of the subject of our research, which aims to use GIS MapInfo systems as a means to snipe (Data Capture) and storage (Data Storage) and address (Data Processing) and directed by spatial information (Spatial Data) and link them to the descriptive information (Attribute Data). To develop a modern digital data and charts the base of each of these elements of the urban service lines equipment and mechanisms, ... etc. As a tool available to those creating and carrying out urban spaces, as well as decision-makers. It was concluded that the possibilities offered by this system would facilitate the processes of monitoring and management in order to ensure the quality of the service.

(1) Background: This text emphasizes concerns regarding the safety of Spanish police officers at-tributed to inadequate training, employing biomechanics for the analysis and mitigation of risks during Use of Force training. The elevated global prevalence of musculoskeletal disorders under-scores the imperative for effective occupational health measures. The study concentrates on evalu-ating injury risks in novice police officers during Use of Force training. (2) Research method: The movements of police officers were captured using a Rokoko Smartsuit Pro equipped with 19 sen-sors. The Biomechanics of Bodies software processed the data, providing REBA and Marras risk scores. Statistical tests were conducted, and Operational Tactical Procedures (OTP) were inte-grated into police training. A diverse group of officers participated, categorized by training level and equipped with the Rokoko Smartsuit. (3) Results: The study evaluates police force training us-ing REBA and Marras methods. REBA scores indicate a moderate to high injury risk, suggesting effective technique design. ANOVA reveals no significant differences between training levels. Marras analysis, characterized by non-normal distribution, unveils varied risk perceptions among groups via the Kruskal-Wallis test. (4) Conclusions: The analysis of both the REBA and Marras methods implies the effectiveness of the OTP technique in reducing injury risks across dif-ferent training levels. The ANOVA test indicates no significant differences in REBA Maximum Scores between the groups. However, the Kruskal-Wallis test for Marras Probability of high-risk values suggests distinctions in medians between training levels. The combined analysis visually illustrates variations in membership regions between expert, intermediate, and novice groups.

Surveillance is the systematic data collection, analysis, and interpretation essential to planning and implementing control activities. The lack of success in control and surveillance elsewhere for the Ae. aegypti mosquito demands developing new accessible and effective strategies. This work aimed to develop and evaluate an adhesive and lure trap for household indoor and outdoor surveillance of Ae. aegypti. Based on a bibliographic review, four compounds with significant attraction percentages for Ae. aegypti were considered. Our more effective blend was determined by preliminary bioassays using the high-throughput screening system (HITSS) and 90 × 90 cm mosquito cages. We designed a low-cost, pyramid-shaped, sticky cardboard trap to incorporate the selected blend. Semi-field 2 x 2 m cages and field tests were conducted to evaluate its effectiveness through mosquito capture percentages. In laboratory tests, blend number 2 presented an attraction percentage of 47.5 ± 4.8%; while in semi-field cages, a 4-inch, 110-v powered fan was used to disperse the attractants, then a similar capture percentage of 43.2 ± 4.0 % was recorded. Field evaluation of the at-house indoor environment and comparing it with the golden standard BG-Sentinel trap recorded interesting results, i.e., an average of our prototype 6.0 ± 1.5 trapped mosquitoes versus 10.0 ± 2.6. In most Latin American countries, there is a lack of formal and accessible strategies for monitoring adult populations of Ae. aegypti, therefore, must develop tools that reinforce entomological surveillance methods.

Failure to meet the deadlines for the implementation of investment and construction projects is a problem in all countries of the world, and leads to unstable activity of construction companies. The article studies the most important destabilizing factors affecting the main indicator of sustainable activity of construction companies-the duration of the implementation of an investment and construction projects. To determine and assess the impact of destabilizing factors on the duration of implementation of selected investment and construction projects, a survey was conducted, in which a number of customers, consultants and contractors involved in construction projects took part. Questionnaires developed on the basis of a cluster sample were sent to respondents, 48 responses were received in response to the assessment of destabilizing factors. To analyze the received and grouped information, structural equation modeling using the Smart-PLS program was used. As a result of modeling, a number of results were obtained, the most important of which are the identification of the main reasons that lead to an average (20% - 50%) increase in the duration of projects in the construction sector. The most significant were: the lack of an appropriate procurement program for materials; inefficient scheduling by contractors and instability of construction production; poor-quality processing of incoming information and untimely deci-sion-making due to changes in projects during their implementation. Destabilizing factors con-tribute to an increase in the duration of construction sector projects, which leads to time overruns, cost overruns, and an increase in the negative impact on the overall use of resources. As a result of the study, a set of recommendations was formed, the most important of which is the use of possible compensatory measures that can allow construction companies to eliminate the risks of disrupting construction deadlines for sustainable activities. These compensatory measures include: - recommendations to customers of the construction project; - recommendations to contractors; - recommendations to the consultant. Moreover, the control of destabilizing factors that can cause delays, the improvement of contracts and the precise and clearer definition of all elements of the project can help to reduce the duration of construction, and will allow companies to maintain sustainable activities in the construction industry.

Electric streamer discharges (streamers) in air are a very important stage of lightning, taking place before formation of the leader discharge, and with which an electric discharge starts from conducting objects which enhance the background elecric field, such as airplanes. Despite years of research, it is still not well understood what mechanism determines the values of streamer parameters, such as its radius and propagation velocity. The Streamer Parameter Model (SPM) is aimed to understand this mechanism, as well as to provide a way to efficiently calculate streamer parameters. Previously, we demonstrated that SPM results compared well with a limited set of experimental data. In this Brief Report, we compare SPM predictions to the published hydrodynamic simulation (HDS) results.

Classical mechanics describes the laws of motion in the macroscopic material world, while quantum mechanics describes the laws of motion in the microscopic material world that classical mechanics cannot explain, and achieves a highly accurate mathematical representation of the laws of microscopic physical motion. But even with such a successful theory, there is confusion about the probability wave. Therefore, this paper attempts to improve the physical definition of the conceptual basis of quantum mechanics, thus solving the confusion of quantum mechanical probability waves, and finally surprisingly discovered another feasible interpretation of the principle of cosmic redshift and the invariance of the speed of light.

J. C. Maxwell, B. Riemann and H. Poincar$\acute{e}$ have proposed the idea that all microscopic particles are sink flows in a fluidic aether. Following this research program, a previous theory of gravitation based on a mechanical model of vacuum and a sink flow model of particles is generalized by methods of special relativistic continuum mechanics. In inertial reference frames, we construct a tensorial potential which satisfies the wave equation. Inspired by the equation of motion of a test particle, a definition of a metric tensor of a Riemannian spacetime is introduced. Applying Fock's theorem, generalized Einstein's equations in inertial systems are derived based on some assumptions. These equations reduce to Einstein's equations in case of weak field in harmonic reference frames. There exist some differences between this theory and Einstein's theory of general relativity.

In recent years, nocturnal ozone enhancement(NOE) events have become a hot research topic in the field of atmospheric environment. By using statistically-based data analysis, we made a comparative investigation about nocturnal ozone concentrations and NOE events in 2022 and 2023, and further explored the effects of NOE events on O3 and PM2.5 at the night of the same day and the next day. The results showed that from 2022 to 2023 in Dongying, the annual average nocturnal ozone concentrations increased from 51 μg/m3 to 59 μg/m3, and the frequency of NOE events was higher in spring, summer and autumn, and lower in winter. NOE events not only had an obvious promoting effect on nocturnal O3 and Ox, and the daily maximum 8 h average concentration of O3 (MDA8-O3) of the same day (more apparent in summer and autumn), and nocturnal PM2.5 and PM2.5-bounded NO3- and SO42- (more apparent in winter), but also had a distinct influence on O3, Ox and MDA8-O3 of the next day (more apparent in summer). The results could strengthen the understanding of the phenomena of NOE events, and provide a scientific basis for the collaborative control of PM2.5 and ozone in urban areas in the Yellow River Delta, China.

(1) Background: The aim of this study was to analyze the relationship between the serum levels of soluble transferrin receptor (sTfR) and interleukin 4 (IL-4), and disease activity and organ mani-festations in SLE patients. (2) Methods: We studied 200 SLE patients and 50 controls. We analyzed disease activity, organ involvement, serum sTfR, IL-4, and interleukin-6 (IL-6) levels, and antinu-clear and antiphospholipid antibody profiles. (3) Results: The median serum levels of sTfR (p>0.000001) and IL-4 (p<0.00001) were higher in the study group than in the controls. SLE patients, compared to the controls, had significantly lower HGB levels (p<0.0001), a lower iron concentration (p=0.008), a lower value of total iron-binding capacity (TIBC) (p=0.03), and lower counts of RBC (p=0.004), HCT (p=0.0004), PLT (p=0.04), neutrophil (p=0.04), and lymphocyte (p<0.0001). Serum sTfR levels were negatively correlated with lymphocyte (p=0.0005), HGB (p=0.0001) and HCT (p=0.008), and positively correlated with IL-4 (p=0.01). Elevated serum sTfR >2.14 mg/dL was associated with an increased risk of myocardial infarction (OR: 10.6 95 CI 2.71–464.78; p=0.001), ischemic heart disease (OR: 3.25 95 CI 1.02–10.40; p=0.04), lung manifestations (OR: 4.48 95 CI 1.44–13.94; p=0.01), and hematological manifestations (OR: 2.07 95 CI 1.13–3.79; p=0.01), and with a reduced risk of neuropsychiatric manifestations (OR: 0.42 95 CI 0.22–0.80; p=0.008). Serum IL-4 was negatively correlated with CRP (p=0.003), and elevated serum IL-4 levels > 0.17 mg/l were associated with a reduced risk of mucocutaneous manifestations (OR: 0.48 95 CI 0.26–0.90; p=0.02). (4) Conclusions: In SLE patients, elevated serum levels of sTfR were associated with an increased risk of cardiovascular, pulmonary, and hematological manifestations, and with a decreased risk of neuropsychiatric manifestations. In contrast, elevated serum IL-4 levels were associated with a decreased risk of mucocutaneous manifestations.

Previous studies detail that the different blood groups are associate to incidence of oxidative stress-related diseases such as certain carcinomas. Bioactive compounds represent an alternative to prevent this oxidative-stress. The aim of this study was to elucidate the impact of blood groups on the erythroprotective potential of Fucoxanthin, β-Carotene, gallic acid, quercetin, and ascorbic acid as therapeutic agents against oxidative-stress. The impact of ABO blood groups on the erythroprotective potential was evaluate by the elucidated antioxidant capacity, blood biocompatibility, blood susceptibility and erythroprotective potential (membrane stabilization, in vitro photostability and antihemolytic activity). All antioxidant tested exhibited a highest potent antioxidant capacity and presented the ability to inhibit ROO•-induced oxidative-stress without compromising the cell membrane, providing an erythroprotective effect dependent on the blood group. Effect that increased in the presence of antigen A. This result could be key to the prevention of carcinomas associated with antigen A, such as breast and skin cancer. These results revealed a probable relationship between the different erythrocyte antigens with the erythroprotective potential, highlighting the importance of bio-targeted drugs for groups mostly susceptible to certain chronic-degenerative pathologies. These compounds could be applied as additive, nutraceutical or encapsulated to improve its bioaccessibility.

Ovarian hyperstimulation syndrome (OHSS) is the main severe complication of the ovarian stimulation for in vitro fertilization (IVF) cycles. The aim of the current study was to identify the interventions for prevention of and reduction in the incidence and severity of OHSS in patients who undergo IVF not included in systematic reviews with meta-analysis of randomized controlled trials (RCTs), assess and grade their efficacy and evidence base. The best available evidence for each specific intervention was identify, analyzed in terms of safety/efficacy ratio and of risk of bias, and graded using Oxford Centre for Evidence-Based Medicine (CEBM) hierarchy of evidence. A total of 15 interventions to prevent OHSS were included in the final analysis. In IVF population not at high risk for OHSS, follitropin delta for ovarian stimulation may reduce the incidence of early OHSS and/or preventive interventions for early OHSS. In high-risk patients, inositol pretreatment, ovulation triggering with low doses of urinary hCG, and the luteal phase administration of GnRH antagonist may reduce the OHSS risk. In conclusion, even if not supported by systematic reviews with homogeneity of the RCTs, several treatments/strategies to reduce the incidence and severity of OHSS have shown to be promising.

Novel pH responsive semi-interpenetrating polymer hydrogels based on tamarind gum-co-poly(acrylamidoglycolic acid) (TMGA) polymers have been synthesized using simple free radical polymerization in the presence of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker and potassium persulfate as a initiator. In addition, these hydrogels have been used as templates for green synthesis of silver nanoparticles (13.4±3.6 nm in diameter, TMGA-Ag) by using leaf extract of Teminalia bellirica as reducing agent. Swelling kinetics and equilibrium swelling behavior of the TMGA hydrogels have been investigated in various pH environment the maxium % equilibrium swelling behavior observed i.e., 2882±1.2. The synthesized hydrogels and silver nanocomposites have been characterized by the UV, FTIR, XRD, SEM and TEM. TMGA and TMGA-Ag hydrogels have been investigated to study the characteristics of drug delivery and antimicrobial study. Doxorubicin hydrochloride, a chemotherapeutic agent successfully encapsulated with maximum encapulstaion efficiency i.e., 69.20±1.2 and performed in vitro release studies in pH physiological and gastric environment at 37 ℃. The drug release behavior is examined with kinetic models such as zero order, first order, Higuchi, Hixson Crowell, Korsmeyer-Peppas. These release data was the best fitted with the Korsemeyer-Peppas transport mechanism with n=0.91. Treatment effect on HCT116 Cell, human colon cancer cells were assessed with cell viability and cell cycle analysis. Antimicrobial activity of TMGA-Ag hydrogels is studied against to Staphylococcus aureus and Klebsiella pneumonia. Finally, the results demonstrate that TMGA and TMGA-Ag are promising candidates for anti-cancer drug delivery and inactivation of pathogenic bacteria, respectively.

Background and objectives: Induction chemotherapy (ICT) before definitive chemoradiation (CRT) gives high response rates in LA-SCCHN. However, pre-ICT gross tumour volume (GTV) for radiotherapy (RT) planning is still recommended. As ¹⁸F-FDG PET/CT has an advantage of biological tumour information comparing to standard imaging methods, we aimed to evaluate the feasibility of ¹⁸F-FDG PET/CT-based post-ICT GTV delineation for RT planning in LA-SCCHN and to assess the prognostic value of PET parameters: maximum standardized uptake value (SUV_max), metabolic tumour volume (MTV) and total lesion glycolysis (TLG). Methods: 47 LA-SCCHN patients were treated with 3 cycles of ICT (docetaxel, cisplatin, and 5-fluorouracil) followed by CRT (70 Gy in 35 fractions with weekly cisplatin). Pre- and post-ICT PET/CT examinations were acquired. Planning CT was co-registered with post-ICT PET/CT and RT target volumes were contoured according to post-ICT PET. Post-ICT percentage decrease of SUV_max, MTV and TLG in primary tumour and metastatic regional lymphnodes (LN) was counted. Loco-regional failure patterns, 3-year progression free (PFS) and overall survival (OS) were evaluated. Results: 3-year PFS and OS rates for study population were 67% and 61% respectively. 31.9% of patients progressed loco-regionally. All progresses were localised in high-to-intermediate dose (60–70 Gy) RT volumes and none in low dose (50 Gy) volumes. Decrease of SUV_max ≥74% (p = 0.03), MTV ≥ 68% (p = 0.04), TLG ≥ 76% (p = 0.02) in primary tumour, and LN TLG decrease ≥74% (p = 0.03) were associated with PFS. Decrease of primary tumour SUV_max ≥ 74% (p = 0.04), MTV ≥ 69% (p = 0.04), TLG ≥ 74% (p = 0.02) and LN TLG ≥ 73% (p = 0.02) were prognostic factors for OS. Conclusions: According to our results, 18F-FDG PET/CT-based post-ICT GTV delineation is feasible strategy without negative impact on loco-regional control and survival. Percentage decrease of metabolic PET parameters SUV_max, MTV and TLG has a prognostic value in LA-SCCHN.

It is required to manage sustainable Short-Rotation Coppices (SRCs) as an important role on carbon sink and bioenergy output, because most of SRCs were established in reclaimed land in South Korea. However, during the last three years, growth pattern of the SRCs was remarkably changed with soil condition. This study aimed to identify the sustainability of SRCs on carbon storage, biomass and fuel pellet production, monitoring the neighboring vegetation of SRCs by land-use exchange, physiological change of poplar on seasonal trend, and to evaluate whether poplar is suitable for making wood pellets. The calculated biomass yield per area of poplar grown was 103.07 Mg per total area (55.6 ha), and volumes of carbon dioxide absorption was estimated to be 330 Mg CO2. Wood pellet quality based on the criteria scored third grade, indicating that poplar is suitable for manufacturing fuel pellets. Moreover, monitoring of the flora distribution in SRCs revealed changes in species composition. As halophyte was increased during drought, soil organic matter, net growth and total chlorophyll of poplar were significantly decreased. These findings indicated that photosynthesis and growth pattern of SRCs may be negatively affected by microclimate and will provide valuable information for effective management of SRCs.

The jalapeño pepper is a vegetable of great economic importance worldwide. However, low germination efficiency, weak seedlings, and a high mortality rate during transplant compromise the viability and sustainability of the crop. An innovative solution is the nanopriming tech-nique, an emerging and novel technology, which involves the imbibition of seeds for a specific period using mineral nanoparticles. The addition of micronutrients such as Zinc and Molyb-denum has been used in seed germination and early seedling development due to their crucial roles. The aim of this study was to evaluate the effectiveness of using Zinc-Molybdenum nano-priming in Jalapeño Pepper on germination and early growth. The results showed that applying nanopriming 124-10 mg L−1 of Zinc-Molybdenum promotes effectiveness on the imbibition and germination of jalapeño pepper seeds, resulting in heavier seeds with better initial absorption. This method not only improves germination rates and seedling vigor but also points towards more sustainable and efficient agriculture. Building on these findings, the Zinc-Molybdenum nanopriming method could potentially transform jalapeño pepper cultivation by enhancing seed quality and resilience. This could lead to more robust crop yields and reduce the need for chemical inputs such as fertilizers and pesticides, thus lowering production costs and environ-mental impact.

Perioperative dysglycemia in cardiac surgery is associated with poor outcomes. Glycemic variability rather than glucose levels are a predictor of length of ICU stay, rise in creatinine and acute kidney injury after cardiac surgery. Glycated haemoglobin (HbA1c) values correspond closely with average blood glucose levels and cut off values can be used to define diabetic and pre-diabetic status. These have been correlated with perioperative events. This narrative review discusses the role of glycated hemoglobin in cardiac surgery.

Constructing a globally consistent high-precision map is essential for the application of mobile robots. Existing optimization-based mapping methods typically constrain robot states in pose space during the graph optimization process, without directly optimizing the structure of the scene, thereby causing the map to be inconsistent. To address the above issues, this paper presents a three-dimensional (3D) LiDAR mapping framework (i.e., BA-CLM) based on LiDAR bundle adjustment (LBA) cost factors. We propose a multivariate LBA cost factor, which is built from a multi-resolution voxel map, to uniformly constrain the robot poses within a submap. The framework proposed in this paper applies the LBA cost factors for both local and global map optimization. Experimental results on several public 3D LiDAR datasets and a self-collected 32-line LiDAR dataset demonstrated that the proposed method achieves accurate trajectory estimation and consistent mapping.

We performed a literature review to identify articles regarding the state of urological cancers in low-to-middle income countries (LMIC). The challenges that LMIC face are multifactorial and can include, poor health education, inadequate screening, as well as limited access to treatment options and trained urologists. Many of the gold standard treatments in high income countries (HIC) are scarce in LMIC due to their poor socioeconomic status leading to advanced stage of disease at diagnosis and ultimately a higher mortality rate. These standards of care are vital components of oncological disease management, however, the current and sparse literature available from LMIC indicate that there are many obstacles delaying early diagnosis and management options in LMIC. In the era of evolving medical diagnosis and treatments, sufficient data must be gathered and understood in order to provide appropriate diagnostic and treatment options to curtail rising mortality rates, and therefore help to alleviate the bur-den in LMIC.

This paper presents computer and color vision research focusing on human color perception in VR environments. A VR art gallery with digital twins of original artworks is created for this experiment. In this research, the field of colorimetry and the application of CMYK and RGB color models are applied. The interrelationships of the two colors models are applied to create a color modification of the VR art gallery environment using C# Script procedures. This color-edited VR environment works with a smooth change of color tone in a given time interval. At the same time, a sudden change in the color of the RGB environment is defined in this interval. This experiment aims to record a user's reaction embedded in a VR environment and the effect of color changes on human perception in a VR environment. The research uses lie detector sensors that record the physiological changes of the user embedded in VR. Five sensors are used to record the signal. An experiment on the influence of the user's color perception in a VR environment using lie detector sensors has never been conducted. This research defines the basic methodology for analyzing and evaluating the recorded signals from the lie detector. The presented text thus provides a basis for further research in the field of colors and human color vision in a VR environment and lays an objective basis for use in many scientific and commercial areas.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

Elastic yarns are the key component of high-performance compression garments. However, it remains a challenge to fabricate anti-fatigue yarns with high mechanical force and long elongation for generating compression garments with prolonged wear. In this paper, we report the development of anti-fatigue double-wrapped yarns with excellent mechanical properties by wrapping high-denier Spandex with nylon filaments in opposite twists. In particular, 560D high-denier Spandex as the core was untwisted which can maximumly reduce the interaction between the core and wrapping filaments, enabling high elongation of the double-wrapped yarns. In addition, we chose 70D nylon filaments with a tensile force of 387.40 ± 8.82 cN as the wrapping materials to provide sufficient force for double-wrapped yarns. Notably, opposite twists were induced for the inner and outer wrapping filaments to achieve a balanced stable yarn structure. By systematically optimizing manufacturing parameters including inner wrapping density, outer wrapping density, taking-up ratio, and drafting ratio, we obtained double-wrapped yarn with excellent tensile force (952.00 ± 24.03 cN) and elongation (357.28% ± 9.10%). Notably, the stress decay rate of optimized yarns was only 12.0% ± 2.2%. In addition, the optimized yarn was used as the weft-lining yarn for generating weft-lined fabrics, the elastic recovery rate of the obtained fabric was only 2.6% after cyclic stretching, much lower than the control fabric. Our design of anti-fatigue double-wrapped yarns could be widely used for fabricating high-performance compression garments.

The Bacillus megaterium LVN01 species native to Colombia has demonstrated the ability to metabolize different co-products or industrial waste (such as fique juice, cane molasses, residual glycerol) and accumulate polyhydroxybutyrate (PHB), giving it potential in the bioplastics industry. In this research, the potential of liquid digestate as a carbon source for the production of PHA in fermentation processes with this bacterial strain was evaluated. Favorably, it was found that B. megaterium utilizes the nutrients from this residual substrate to multiply appropriately and efficiently synthesize poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV). Bench scale aerobic batch fermentation, under the operational conditions of this research [Volume: 3L; Temperature: 30.8°C; Agitation: 400 rpm; pH: 7.0 ± 0.2; Disolved Oxygen: 100% saturation; Antifoam 10% (v/v)], generated maximum values of DCW (0.56 g cell L-1) at 60 h, while the maximum PHB yield (360 mg PHB L-1) occurred at 16 h, which is very favorable for sustainable degradable bioplastics production. Additionally, GC-MS and NMR analyses confirmed that the PHBV copolymer synthesized by B. megaterium is made up of the monomers 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV). Furthermore, the thermal properties determined by TGA (Tonset=283.1 ºC, Tendset= 296.98 ºC. Td =290.114 °C) and DSC (Tm= ºC155.7 °C, ΔHf= 19.80 J g-1, Xcr = 18.17%), indicate that it is a thermally stable biopolymer with low percentages of crystallinity, providing flexibility that facilitates molding, adaptation, and application in various industrial sectors.

A very detailed water budget was conducted on Lake Trafford in southern Florida. The inflow was dominated by surface-water influx via five canals (61%) with groundwater influx constituting 12% and direct rainfall 27%. Lake discharge was dominated by sheet-flow (69%) and evapotranspiration (30.5%) with groundwater recharge of the hydraulically connected unconfined aquifer accounting for only 0.5%. Removal of 30 M tons (4.4 x 106 m3) of organic sediment impacted groundwater influx, causing enhanced groundwater flows into the deeper parts of the lake and mixed flows along the banks creating a rather unusual pattern. The large number of groundwater seepage meters used during the investigation led to a very reliable set of measurements with occasional failure of only a few meters. A distinctive relationship was found between the wet season lake stage, heavy rainfall events and pulses of exiting sheet-flow from the lake. Estimation of the evapotranspiration loss using data collected from a weather station on the lake allowed the use of three different models which, when averaged, produced results comparable to Lake Okeechobee (southern Florida). A limitation of the investigation was the inability to directly measure sheet-flow discharges, which had to be estimated as a residual within the calculated water budget.

Access to medical care is a global issue. Technology-aided approaches have been applied in addressing this. Interventions have however not focused on medical diagnosis as a fully automated procedure and available applications employ mainly text-based inputs rather than conversation in natural language. We explored the utility of ontology-based chatbot technology for the design of intelligent agents for medical diagnosis through a systematic review of the most recent related literature. English articles published in 2011-2016 returned 233 hits which yielded 11 relevant articles after a 3-stage screening. Findings showed that the creation of expert systems had been the focus of many the studies which utilize the physician-system-patient framework with system training based mostly on expert knowledge for designing web- or mobile phone-based applications that serve assistive purposes. Findings further indicated gaps in the design and evaluation of more effective systems deployable as standalone applications, for example, on an embodied robotic system. The need for technology supporting the physical examination part of diagnosis, connection to data sources on patients’ vitals and medical history are also indicated in addition to the need for more qualitative work on natural language-based interaction. The system should be one that is continuously learning. Future works should also be directed towards the building of more robust knowledge base as well as evaluation of theory-based diagnostic methodological options

Background/Aim: microRNAs (miRNAs) are key regulators of both physiological and pathophysiological mechanisms in diabetes and gastrointestinal (GI) dysmotility. Our previous studies have demonstrated the therapeutic potential of miR-10a-5p mimic and miR-10b-5p mimic (miR-10a/b mimics) in rescuing diabetes and GI dysmotility in murine models of diabetes. In this study, we elucidated the safety profile of a long-term treatment with miR-10a/b mimics in diabetic mice. Methods: Male C57BL6 mice were fed a high-fat, high-sucrose diet (HFHSD) to induce diabetes and treated by five subcutaneous injections of miR-10a/b mimics for a 5-month period. We examined the long-term effect of the miRNA mimics on diabetes and GI dysmotility, including an assessment of cancer risk as well as liver and colon inflammation using cancer and inflammatory biomarkers. Results: HFHSD-induced diabetic mice subcutaneously injected with miR-10a/b mimics monthly for 5 months exhibited a marked reduction in fasting blood glucose levels with restoration of insulin and significant weight loss, improved glucose and insulin intolerance, and restored GI transit time. In addition, the miR-10a/b mimic treated diabetic mice showed no indication of risk for cancer development and inflammation induction in the liver, colon, and blood for the 5 months post injections. Conclusion: This longitudinal study demonstrates that miR-10a/b mimics, when subcutaneously administered in diabetic mice, effectively alleviate diabetes and GI dysmotility for 5 months with no discernible risk for cancer or inflammation in the liver and colon. The sustained efficacy and favorable safety profiles position miR-10a/b mimics as promising candidates in miRNA-based therapeutics for diabetes and GI dysmotility.

We have found a region in the northwestern Japan Sea near the Subpolar Front where mesoscale eddies regularly form and circulate. The anticyclonic eddy with a strong dynamic feature, vertically extended to the bottom (~3500 m), multilayer core structure and extreme values of temperature and salinity was sampled there in the cruise in May 2004. The altimetry-based eddy tracking showed that it had a life span of nine months with the size reaching 120 km. CTD observational data were used to explore the eddy’s features and vertical structure. The eddy had a multilayer core with different thermohaline characteristics which could be originated by eddy interaction with the surrounding waters during its life. The evolution of the eddy has been studied and analyzed with the help of altimetry-based Lagrangian indicators of water motion. Performing the particle-tracking numerical experiments, we computed the Lagrangian maps that contain information on the origin of water inside the eddy core and its ‘age’ on every day of the eddy’s life. Inspecting daily-computed Lagrangian maps, we documented the essential events in the evolution of the eddy including its formation, splitting, merger, entrainment and detrainment of water, erosion and eventual decay. All these observations have been verified with the infrared satellite images. The new Lagrangian technique has been applied to calculate day by day the content of water of various origin (coastal, subtropical and subarctic) entrained into the eddy core. It has been found that the surface core has been filled mainly with subtropical water originated in the southern flank of the Subpolar Front. The episodes with cardinal changes of ratio of different water types have been recorded and verified with the infrared satellite images and maps of the origin of water inside the eddy core.

Background: Although Tuberculosis (TB) is one of the oldest diseases known to mankind, many practitioners are still unaware of various aspects of management of TB including drug resistant TB. To be able to make an impact on the disease burden we need to understand the knowledge, attitude and practices (KAP) of practitioners, both in government and private sector, towards TB case management. Methodology: A random cross-sectional survey of 99 respondents to assess the KAP towards TB case management using a digital semi-structured questionnaire which was pre-tested and administered to allopathic practitioners from across States in North and Central India. Results: 77% responders were government doctors and 23% were private practitioners. Chest physicians accounted for 61% of the responders. 26% of government and 78% of private doctors relied on sources which are difficult to validate for their knowledge on drug resistant TB management. There were large variations seen in knowledge on modes of transmission, standard precautions, extent of drug resistant TB, diagnostics as well as treatment regimen for drug resistant TB. Conclusion: The knowledge of both sector doctors especially amongst private practitioners with respect to the awareness of extent, diagnosis, and treatment and infection control measures for drug resistant TB is suboptimal which translates to poor diagnostic, therapeutic and infection control choices amongst private practitioners. If India has to achieve the targets for TB Elimination by 2025, serious work needs to be done to upgrade the knowledge of the private sector doctors on drug resistant tuberculosis. The Ministry of Health and Family Welfare, GoI needs to have regular educational programs for the private practitioners coupled with awareness campaigns and frequent surveys to assess the knowledge, attitude and practices being followed in the private sector for TB management including drug resistant TB.

Lifestyle physical activity (PA) and nutrition are known to be effective interventions in preventing and managing obesity related comorbidities is adult populations, but less so in children and adolescents. We examined the effectiveness of lifestyle interventions in children from minority ethnic populations in western high-income countries. Our systematic review included 53 studies involving 26045 children from minority ethnic populations within western countries, who followed lifestyle intervention programs lasting between 8 weeks and 5 years with an aim to prevent and/or manage childhood obesity and associated comorbidities, including adiposity and cardiometabolic risks. Studies were heterogenous in terms of lifestyle intervention components (nutrition, PA, behavioural counselling) and settings (community vs. schools and after schools). Our meta-analysis included 31 eligible studies and showed no significant effects of lifestyle interventions when they focused on body weight and body mass index (BMI) outcomes [pooled BMI mean change = -0.09 (95% CI -0.19, 0.01), p=0.09]. This was irrespective of the intervention program duration (< 6 months vs. ≥ 6 months), type (PA vs nutrition/combined intervention) and weight status (overweight or obese vs no normal weight), all showed no significant effects in the sensitivity analysis. Nonetheless, 19 of the 53 studies reported reduction in BMI, BMI z scores and body fat percentage. However, majority of lifestyle interventions adopting a quasi-design with a combined primary and secondary obesity measures (11 out of 15 studies), were effective in reducing obesity comorbidities of cardiometabolic risks including metabolic syndrome, insulin sensitivity, and blood pressure in children with overweight and obesity. Preventing childhood obesity and associated comorbidities in children from high-risk ethnic minority groups is best achieved using a combined PA and nutrition intervention approach, which jointly target preventing obesity and cardiometabolic disease primary and secondary outcomes, especially measures of diabetes, hypertension, and cardiovascular disease.

Coincident changes in abundance and behavior pose a challenge for interpreting abundance data from monitoring programs. In the San Francisco Estuary, long-term monitoring documented the declines of many species including the anadromous Longfin Smelt (Spirinchus thaleichthys). We identified seasonal patterns in reginal presence of Longfin Smelt through its life cycle using monitoring data and generalized additive modelling. We then investigated the year-to-year variability in the seasonal patterns of presence using functional data analysis (FDA). FDA separated the variability due to population size from variability due to differences in timing of presence. We found that Longfin Smelt have consistent seasonal distribution patterns and that two trawl types were needed to accurately describe those patterns. After accounting for variability due to year-class strength, shifts in the timing of presence were evident in three regions. The most variable period for the upstream regions Suisun Bay and West Delta was for age-0 fish in summer and for the downstream region Central Bay was for age-0 fish in late fall. This manifested as a delay in the typical fall re-occupation of upstream regions that comprise the study area for another monitoring study (Fall Midwater Trawl). Thus, a portion of the recent reductions in Fall Midwater Trawl abundance of Longfin Smelt resulted from changes in behavior rather than a decline in abundance. The presence of multiple monitoring surveys allowed analysis of distribution from one data set to aid interpretation of patterns in abundance from another monitoring survey. This study highlights how identifying portions of the life cycle with the most and least variability in distribution can help inform the types of management strategies that will be most effective. It also illustrates an analytical method that can be used to address the problem of confounded effects of abundance and behavior on patterns in monitoring data.

The modification the gut microbiota in metabolic syndrome and associated chronic diseases is among leading tasks of microbiome research and needs for clinical use of probiotics. Evidence lack for the implications for microbiome modification to improve metabolic health in particular when applied impersonalized. Probiotics have tremendous potential in personalized nutrition and medicine to develop healthy diets. The aim was to to conduct comprehensive overview of recent updates of role of microbiota on human health and development of metabolic syndrome and efficacy of microbiota modulation considering specific properties of probiotic strain and particular aspects of metabolic syndrome and patient`s phenotype to fill the gap between probiotic product and individual to facilitate development of individualized / personalized probiotic and prebiotic treatments. We discuss the relevance of using host phenotype-associated biomarkers, those based on imaging and molecular and patrient`s history, reliable and accessible to facilitate person-specific appication of probiotics and prebiotic substances. Microbiome phenotypes can be parameters of predictive medicine to recognize patient`s predispositions and evaluate treatment responses; the number of phenotype markers can be effectively involved to monitor microbiome modulation. The studied strain-dependent properties of probiotic strains are potentially relevant for individualized treatment for gut and distant sites microbiome modulation. The evidence regarding probiotic strains properties can be taken to account via pathophysiology-based approach for most effective individualized treatment via gut, oral and vaginal and other sites microbiome modulation according to phenotype of the patient providing individualized and personalized medical approaches. Preventive potential of probiotics is strong and well-documented. Recommendations for individualized clinical use of probiotics, and for probiotic studies design have been suggested.

Objective To investigate the functional and biological significance of telomere-related active genes in cholangiocarcinoma (CCA) using single-cell sequencing and cell communication analysis. Methods First, we identified and annotated different cell types in CCA samples using single-cell sequencing data. Pseudotime analysis revealed the transcriptional status and differentiation process of CCA cells. We then explored interactions between CCA cells and their regulatory pathways through cell communication analysis. 47 key genes related to telomere activity were identified, and GO and KEGG pathway enrichment analysis was performed. Additionally, we constructed a prognostic model and verified the model's predictive efficacy. Finally, we identified genes associated with drug sensitivity in CCA patients and identified pathways associated with CCA prognosis through tumor TMB analysis. Results We identified 452 active telomere-associated cells. Then, we assessed telomere associated gene activity, obtaining 47 differentially expressed telomere genes by intersecting with CCA differentially expressed genes. Major up-regulated signaling pathways, including MIF-(CD74+CXCR4) and HLA-A-CD8A, were identified through pseudotime analysis. Three telomere-associated prognostic genes were identified using LASSO analysis, and prognostic-related models were built. In addition, PBRM1 mutation load was found to be highest in the high-risk group, making it a potential diagnostic target. Finally, drug sensitivity analysis revealed higher sensitivity to certain therapeutic drugs in the high-risk group, providing guidance for tailored CCA treatment. Conclusion The MIF-(CD74+CXCR4) and HLA-A-CD8A signaling pathways appear to be major pathways for CCA cell proliferation. Prognostic models based on telomere-associated genes show promise for application, indicating the biological and clinical significance of telomere activity genes in CCA.

The motivation for investigating the issues presented in this article stemmed from a need to understand better the relationship in long-established physics formulas and extract the information they provided using conventional methods. Based on the definition of magnetic flux quantization, which is based on a combination of fundamental physical constants, the Planck constant, and the particle’s elementary charge, this work explores the results that arise when this equation is combined with the equation of the Bohr-level electrostatic force acting on the electron, which leads to a new mathematical relationship between the combined expressions. The new relationship yields novel theoretical findings related to the known universal constants. Following this insight, the formalism developed in this paper indicates that the mass of the electron and other subatomic particles is associated with the magnitude of the square of the magnetic flux quantum, which makes up the particle. This conclusion is not as strange as it may seem, as the square of the magnetic flux quantum appears in the context of magnetic energy in a current loop and, according to Einstein’s special theory of relativity, energy is equivalent to mass. Another aspect described at the end of this paper demonstrates the connection between the square of the magnetic flux quantum through the Bohr radius and the significance of the wave function in the atom. The theoretical results are in full accordance with experimental results published by NIST CODATA 2018 that I’ve used, which validates the existence of the relationship.

Nucleocytoplasmic large DNA viruses (NCLDVs) have massive genomes and particle sizes compared to other known viruses. NCLDVs, including poxviruses, encode ATPases of the FtsK/HerA superfamily to facilitate genome encapsidation. However, their biochemical and structural characteristics are yet to be discerned. In this study, we demonstrate that the viral ATPases are significantly shorter than their bacterial homologs, representing the minimal ATPase core of the FtsK/HerA superfamily. We analyzed the sequence and structural features of the vaccinia virus A32 protein and determined their roles in the stability of the A32 protein and its ATPase activity. We sought to purify A32 by various techniques and noted that recombinant A32 expressed in E. coli is highly insoluble and unstable in solution, possibly because of the disordered C-terminus. N-terminal fusion with the thioredoxin solubility tag could alleviate this issue to some extent, but subsequent tag cleavage results in increased susceptibility to precipitation and degradation. We also predicted a conserved coiled-coil motif (CCM) towards the C-terminus of VV A32. ATPase activity of A32 is known to increase in the presence of DNA. Our comparative analysis of wildtype A32 versus CCM mutants suggests that this DNA dependence of A32’s ATPase activity is likely regulated by the CCM. Since CCM is also known to facilitate protein oligomerization, these findings provide new opportunities for further detailed characterization of A32.

The effects of simulated acid rain (SAR) on the photosynthetic performance of subtropical coniferous species have not been thoroughly investigated. In this study, we treated two coniferous species, Pinus massoniana (PM) and Cunninghamia lanceolata (CL), with SAR and then analyzed photosynthetic activities via the simultaneous measurement of prompt fluorescence(PF), delayed fluorescence(DF), and modulated reflection at 820 nm(MR820). Following the low-pH SAR treatment, the I–P phase of the OJIP curves of PM and CL decreased significantly and then the K-band and L-band were detectable. The delayed fluorescence for both PM and CL decreased as the pH of the SAR solution decreased, with a more significant decrease in the I1 peak than in the I2 peak. According to the MR820 curve, the exposure to SAR stress inhibited the rapid decrease and slow increase in the MR820 transients of PM and CL. The gradients of the decreasing and increasing phases were lower for CL than for PM at pH 2.5. In addition, SAR decreased the light energy captured per unit area (ABS/CSm) and the quantum yield of electron transfer per unit area (ETO/CSm), but it increased the accumulation of QA−, thereby decreasing primary photochemical efficiency (TRO/CSm, φPO). These changes in photosystem II (PSII) resulted in a decrease in the maximum quantum yield of PSII (Fv/Fm) and the performance index (PIABS). Moreover, PSII was protected from thylakoid membrane photodamages through the increase in heat dissipation per unit area (DIO/CSm) in response to SAR. The increase in δRO as the pH of the SAR solution decreased was observed for PM, but not for CL. Considered together, the study findings suggest that SAR treatments can decrease chlorophyll contents and damage the OEC in PM and CL, which obstructs the transfer of electrons on the donor and acceptor sides of PSII. However, PM is better able to withstand SAR stress than CL, likely because of the activation of a protective mechanism (reflected by the change in δRO). Therefore, in coniferous forest areas severely affected by acid rain, CL may need to be protected more than PM.

The dessert banana is a popular fruit worldwide, but its ripening process is greatly accelerated by high temperatures, which eventually leads to an unpleasant taste and the appearance of spots on the skin of the fruit. To slow down the ripening of bananas, expensive strategies are used, which are usually not practical for conventional farmers in less developed countries. In this study, we try to find a less costly alternative. Therefore, the effects of coatings of lemon peel extract (2.5 %, 5 %, and 10 %), calcium chloride (4 %), and glycerol (2 %) on the shelf life and postharvest quality of banana fruit (Cavendish) stored at 20 ± 3 °C and 50 – 70 % relative humidity were investigated. Treatment with a mixture of 2.5 % lemon peel extract and 2 % glycerol resulted in an extension of the shelf life of the dessert banana by up to 6 days and no detectable fungal infestation. The mixture is an effective alternative to extend the shelf life and reduce quality losses in bananas.

Wild rocket plants were cultivated in a plastic greenhouse into two independent sectors, one for soil-bound (SbS) cultivation and another equipped for soilless (ScS) cultivation systems. In both SbS and ScS, the crop was subjected to treatments consisting in a high-compared to a low-input fertilization program (HF and LF treatment, respectively). Water use efficiency (WUE) and partial factor productivity (PFP) for nutrients (N, P, K, Ca and Mg for ScS, and N for SbS) were measured. Rocket leaves, separated for cultivation system and fertilization program, collected at different cuts during the growing cycle, were cold stored at 10 °C until 16 d. At each sampling day (at harvest and during the storage), sensory parameters, respiration rate, dry matter, colour, electrolyte leakage, antioxidant activity, total phenols, total chlorophyll and ammonia content were evaluated. In ScS, the PFP for all nutrients supplied as fertilizers showed a significant increase with the LF treatment, with values higher than 30 % for N, K and Ca. As for the postharvest performance, rocket leaves cultivated in ScS showed better qualitative traits than those cultivated in SbS, as suggested by the lower values of ammonia content and electrolyte leakage recorded at the end of storage in samples grown in ScS. Moreover, in ScS, data showed a lower membrane damage in LF than HF rocket leaves. Finally, regarding total chlorophyll content, even if no effect of treatments was recorded in SbS, rocket cultivated in ScS, showed a better retention of this parameter applying LF than HF treatment. In addition to this, a PLS model (R2 = 0.7) able to predict the cultivation system, using as variables total chlorophyll content no-destructively measured, was implemented.

The ridge-furrow plastic mulching (RFPM) system and nitrogen application have been effective strategies for improving crop productivity in the Loess Plateau of China. However, it is not clear how the ridge-furrow ratio and nitrogen fertilizer type (NT) affect the utilization of water, nitrogen, heat and radiation resources for increased rain-fed wheat production. Two nitrogen fertilizer types [Traditional urea (TU) and controlled-release urea (CRU)] and four planting patterns [conventional flat planting (F) and the RFPM system of 20 cm ridge with 40 cm furrow (R2F4), 40 cm ridge with 40 cm furrow (R4F4), and 60 cm ridge with 40 cm furrow (R6F4)] were tested from September, 2018 to June, 2021 during winter wheat growing season. The results showed that the RFPM system can increase the soil thermal time (TTsoil) by 41.0–152.1°C d compared to F. The thermal effect of the RFPM system shortens the vegetative growth period and extends the reproductive growth period by 2–7 days, promoting the increase of the leaf area index (LAI) and final dry matter (DM) accumulation. These significantly increased the grain yield (GY) in the RFPM system by 51.6–115.2% and enhanced the thermal time use efficiency (TUE) by 48–99.5%, water productivity (WP) by 37.4–76.3%, radiation use efficiency (RUE) by 16.3–34.4%, and partial factor productivity of nitrogen (PFPN) by 51.6–115.2% compared to F. Although a high ridge-furrow ratio combined with CRU increased GY and resources use efficiency, it also exacerbated the soil water depletion, especially in the 40–140 cm soil layer. Overall, applying CRU in combination with the RFPM system of 40 cm ridge with 40 cm furrow maximized resources use efficiency and increased wheat production in the Loess Plateau of China.

High-temperature cooking process like frying, baking, smoking, or drying can induce chemical transformations in conventional food ingredients, causing deteriorative modifications. These reactions, including hydrolytic, oxidative, and thermal changes, are a common occurrence and can result in alterations to the food's chemical composition. In this study, a combination of sucrose and histidine (Su-Hi) was transformed through a process of charring or pyrolysis. The GC-MS profiling study showed that when sucrose and histidine (Su-Hi) are exposed to high temperatures (≈240°C), they produce carbonyl and aromatic compounds including beta-D-Glucopyranose, 1,6-anhydro (10.11 %), 2-Butanone, 4,4-dimethoxy- (12.89 %), 2(1H)-Quinolinone-hydrazine (5.73%), Benzenamine (6.35%), 2,5-Pyrrolidinedione, 1-[(3,4-dimethylbenzoyl)oxy]- (5.82%), Benzene-(1-ethyl-1-propenyl) (5.62%), and 4-Pyridinamine-2,6-dimethyl (5.52%). The compounds mentioned have the ability to permeate the cell membrane and contribute to the development of cell death by necrosis in human immune cells. The evidence available suggests that a specific set of pyrolytic compounds may pose a risk to immune cells. This investigation reveals the complex relationship between high-temperature cooking-induced transformations, compound permeation inside the cells, and downstream cellular responses, emphasizing the significance of considering the broader health implications of food chemical contaminants.

Obesity and physical activity have opposing effects on cardiorespiratory fitness. This study aimed to investigate the impact of obesity measured by various anthropometric indicators and physical activity level on oxygen uptake and fat oxidation during moderate-intensity aerobic exercise in adults. Forty-eight individuals were recruited. Various anthropometric indicators (i.e., body mass index (BMI), waist circumference (WC), waist-to-hip ratio (WHR), and waist-to-height ratio (WHtR)) were measured. Physical activity was assessed using the International Physical Activity Questionnaire (a short version). Total oxygen uptake (VO2tot) and fat oxidation were recorded during 30-minute aerobic exercise at moderate intensity. There were no differences in oxygen uptake and fat oxidation between obese and non-obese groups. Based on obesity and physical activity, VO2tot was significantly different among groups classified by WHR. Inactive obesity had significantly lower VO2tot 28.1% compared to active obesity and 29.2 % compared to active non-obesity. The inactive obesity had a 3.8%, 27.4%, and 4.3% lower fat oxidation than the active non-obesity, as classified by WC, WHR, and WHtR, respectively. However, the differences were not statistically significant. We conclude that active obesity, as measured by WHR, exhibited higher oxygen uptake compared to inactive obesity. Moreover, inactive obesity showed poorer oxygen uptake than active non-obesity.

Basketball playing entails the repetitive performance of short intense actions using lower limb explosive power. As such, it is important to measure this capability in basketball players, especially among young players, and to optimize training programs and game plans. After presenting an in-depth understanding of the specific physiological requirements when playing basketball, as well as the type of movements required, The aim of this review is to better understand the importance of the physiological energy systems in basketball, to examine the contribution of each energy system and, accordingly, to heighten awareness of the importance and dominance of the alactic anaerobic physiological system in basketball, for actions requiring high level explosive power. This review of the literature depicts the horizontal and vertical physical movements and physiological requirements entailed in playing basketball, and presents eight standardized anaerobic alactic measurement tools relevant to the game. As some of these tests suit a number of ball games, the findings of this review article are important for making order of the elements unique to basketball as well as additional parameters to consider when testing basketball players. By reliably and validly testing the anaerobic alactic capabilities of basketball players, test results can be used for training purposes and for improving game outcomes. Despite the fact that much of the information in this review is familiar to coaches, highlighting the specific needs of basketball may help them to choose the most suitable tools, and may also shed light on new directions for developing basketball-specific assessment tests.

Phosphorus deficiency highly interferes with plant growth and development. Plants respond to the persistent P deficiency by coordinating the expression of genes involved in the alleviation of the stress. Promoters of phosphate transporter genes are of great choice for the development of genetically modified plants with enhanced phosphate uptake abilities, which improve crop yields in phosphate-deficient soils. In our previous study, the sugarcane phosphate transporter PHT1;2 gene, showed a significantly high expression under salinity stress. In this study, the Erianthus arundinaceus EaPHT1;2 gene was isolated and characterized using various in-silico tools. The deduced 542 amino acid residues have 10 transmembrane domains, with a molecular weight and isoelectric point of 58.9 kDa and 9.80, respectively. They displayed 71–96% similarity with Arabidopsis thaliana, Zea mays, and Saccharum hybrid. To elucidate the function of the 5’ regulatory region, the 1.1kb promoter was isolated and validated in tobacco transgenics under Pi stress. The EaPHT1;2 promoter activity was detected using the β-glucuronidase (GUS) assay. While the EaPHT1;2 promoter showed 3 to 4.2-fold higher expression than the most widely used CaMV35S promoter. The 5’ deletion analysis with and without 5’UTR regions, revealed that a small size 374 bp fragment with the highest promoter activity among 5′ truncated fragments, which was 2.7 and 4.2 times higher than the well-used CaMV35S promoter under normal and Pi-deprivation conditions, respectively. The strong and short promoter of EaPHT1;2 with 374 bp showed significant expression in low Pi-stress conditions and it could be a valuable source for the development of stress-tolerant transgenic crops

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

Background and aims: Only one cohort study exists on the incidence of the risk of malnutrition (RM) in older adults, though numerous cross-sectional –and that cohort research– have reported several risk factors associated with the prevalence and incidence of this condition. However, alterations of body composition and impaired physical performance as exposition variables of RM have not been explored. This study assessed the incidence of RM and determined its association with excess fat mass, low total lean tissue, gait speed, and handgrip strength as exposition variables for RM in community-dwelling older adults. Methods: This is a secondary analysis in older adults (≥60 years old) derived from the study “Frailty, dynapenia, and sarcopenia in Mexican adults (FraDySMex)” a prospective cohort project conducted from 2014 to 2019 in Mexico City. At baseline, volunteers underwent body composition analysis and physical performance tests. Several covariates were identified through comprehensive geriatric assessment. At baseline and follow-up, RM was assessed using the long form of the mini nutritional assessment (MNA-LF) scale. Associations between the exposition variables and RM were assessed by multiple logistic regression. Results: The cohort included 241 subjects. Average age was 75.6±7.8 years; 83.4% were women. The mean follow-up period was 4.1 years, during which 28.6% of subjects developed RM. This condition was less likely to occur in subjects with excess fat mass index, even after adjusting for several covariates. RM was also more likely to occur in subjects with low total lean tissue index, according to both an unadjusted model and after adjusting for the corresponding variables. Regarding the association between RM and gait speed, RM was also more likely to occur in subjects with low gait speed according to both the unadjusted and adjusted models. Similar results were found for RM in relation to low handgrip strength; however, after adjusting for the associated covariates, models 1 and 2 no longer reached the level of significance. Conclusion: The risk of malnutrition diagnosed by MNA-LF was significantly less likely to occur among subjects with excess fat mass, but possibility was significantly higher in those with low total lean tissue and low gait speed after 4.1 years of follow-up in community-dwelling older adults. These results highlight that excess fat mass, low total lean tissue, and low gait speed are first than risk of malnutrition and not vice versa.