Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

Synchronous homopolar machines (SHM) with excitation winding on the stator have attracted the attention of researchers for many decades due to their high reliability. They are used in a variety of applications such as aircraft and railway generators and traction motors. At the same time, the three-dimensional structure of their magnetic circuit makes the problem of their analysis and optimization challenging. This problem becomes even more complicated when considering an SHM with hybrid excitation, with ferrite magnets in the rotor slots. The article proposes a mathematical procedure for optimizing a synchronous homopolar generator with hybrid excitation based on the single-criterion Nelder-Mead method and two-dimensional finite element analysis (FEA). The use of the Nelder-Mead method compared to multicriteria methods and 2D FEA compared to 3D FEA makes possible to significantly reduce the computational burden. As a result of optimization, the power loss and torque ripples of the generator are significantly reduced. The article also compares the characteristics of synchronous homopolar generators with and without ferrite magnets.

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.

Background: Developing an efficient and standardized method to isolate and characterize adipose-derived stem cells (ASCs) from the stromal vascular fraction (SVF) of the adipose tissue for clinical application represents one of the major challenges in cell therapy and tissue engineering. Methods: In this study, we proposed an innovative, non-enzymatic protocol to collect clinically useful ASCs within freshly isolated SVF from adipose tissue by centrifugation of the infranatant portion of lipoaspirate and to determine the characteristic cytofluorimetric pattern, prior to in vitro culture. Results: The SVF yielded a mean of 73,32 \pm\ 10,89% cell viability evaluated with CALCEINA-FITC, i.e. cell-permeant dye. The ASCs were positive for PC7-labeled mAb anti-CD34 and negative for both PE-labeled mAb anti-CD31 and APC-labeled mAb anti-CD45. The frequency of ASCs estimated according to the panel of cell surface markers used was 51,06%\ \pm 5,26% versus the unstained ASCs subpopulation that was 0,74%\pm0,84% (P<0.0001). The ASCs events/\muL were 1602,13/\muL \pm 731,87/\muL. Conclusion: Our findings suggested that ASCs found in freshly isolated adipose SVF obtained by centrifugation of lipoaspirate can be immunophenotypically identified with a basic panel of cell surface markers. These findings aimed to provide standardization and contribute to reducing the inconsistency on reported cell surface antigens of ASC derived from the existing literature.

The streptavidin and biotin interaction is one of the strongest non-covalent interactions in nature. As a result, this non-covalent interaction has been of great interest when it comes to biochemical assays, diagnosis of diseases, and cell-targeted drug delivery. Past research has proven that biotin-streptavidin is useful in biosensor development to improve the detection of a system when conjugated to nanoparticles. This study aims to prove that streptavidin-coated nanoparticles can be conjugated with biotinylated antibodies using the primary-secondary method to non-invasively detect adenocarcinoma in-vitro. While the use of nanoparticles is not uncommon to the diagnostics area of scientific research, the technique this research aims to investigate is a non-invasive one, utilizing the primary-secondary method. Specifically, the increased stability of fluorophores when bound to antibodies as opposed to nanoparticles directly can be indicative of the particles conjugated through the primary-secondary method’s ability to specifically bind to overexpressed transferrin receptors in the A549 cell line. In this paper, streptavidin-coated nanoparticles were conjugated with biotinylated anti-transferrin receptor antibodies and AlexaFluor-488 secondary antibodies were used to enable fluorescence-based detection. The efficiency of these particles were observed quantitatively through a plate reader and qualitatively through a fluorescence microscope. I demonstrated that these nanoparticles are able to specifically bind to the target proteins in this study. These findings contribute to the field of nanoparticle diagnostics and can be extended to different diseases caused by overexpression of proteins in the future. While this was conducted in-vitro, conjugates can be prepared to detect cancer in-vivo and can be tested with magnetic relaxometry in the future.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

For bounded unit interval, we propose a new Kumaraswamy generalized (G) family of distributions from a new generator which could be an alternate to the Kumaraswamy-G family proposed earlier by Cordeiro and de-Castro in 2011. This new generator can also be used to develop alternate G-classes such as beta-G, McDonald-G, Topp-Leone-G, Marshall-Olkin-G and Transmuted-G for bounded unit interval. Some mathematical properties of this new family are obtained and maximum likelihood method is used for estimating the family parameters. We investigate the properties of one special model called a new Kumaraswamy-Weibull (NKwW) distribution. Parameter estimation is dealt and maximum likelihood estimators are assessed through simulation study. Two real life data sets are analyzed to illustrate the importance and flexibility of this distribution. In fact, this model outperforms some generalized Weibull models such as the Kumaraswamy-Weibull, McDonald-Weibull, beta-Weibull, exponentiated-generalized Weibull, gamma-Weibull, odd log-logistic-Weibull, Marshall-Olkin-Weibull, transmuted-Weibull, exponentiated-Weibull and Weibull distributions when applied to these data sets. The bivariate extension of the family is proposed and the estimation of parameters is given. The usefulness of the bivariate NKwW model is illustrated empirically by means of a real-life data set.

We propose an improved earlier described “mirror” method [1] for detecting in cell nuclear extracts mutations that arise in DNA during its replication due to misincorporation of deoxyadenosine-5’-monophosphate (dAMP) opposite 7,8-dihydro-8-oxoguanine (8-oxoG). The method is based on the synthesis of a complementary chain (“mirror”) by nuclear extracts of different mice organs on a template containing 8-oxoG inside and dideoxycytidine residue (ddC) at the 3’-end. The “mirror”was amplified by PCR using primers part of which was non-complementary to the template. It allowed obtaining the “framed mirror” products. The misincorporation of dAMP in “framed mirror” products forms an EcoRI restriction site. The restriction analysis of double-stranded “framed mirror” products allows a quantification of the mutation frequency in nuclear extracts. The data obtained showed that the mutagenic potential of 8-oxoG markedly varied in different organs of adult mice and embryos.

The introduction of electrical vehicle charging infrastructure including EV charger, renewable energy resource at secondary feeder in distribution system has been increased as one of countermeasure for global environmental issues. However, the Electric Vehicle Charging (EVC) infrastructure may act as the peak load in distribution system, which can adversely impact on the voltage stability when the electric vehicle is quickly charged. Therefore, to keep within the limit capacity of secondary feeder and allowable limit for feeder voltage, this paper proposes a stabilization method by the Energy Storage System (ESS) control strategy at secondary feeder in order to be not violated over than lower and upper limit. Also, this paper presents the estimation method to keep the proper standard value of State of Charge (SOC). From the simulation results, the voltage stabilization operation by ESS should make the feeder voltages of the distribution system(secondary feeder) introduced EVC Infra keep better voltage conditions, also estimation method to keep the proper standard value is confirmed that the SOC of ESS when is the standby condition could be exactly kept within the proper reference range.

In recent years, numerous topologies of single phase and three phase Field Excited Flux-Switching Machine (FEFSM) have been developed for several applications. Comparative study of three types of single-phase low-priced Field Excited Flux-Switching Machine (FEFSM) is presented in this paper. Both the conventional 8S/4P sub-part rotor design and 6S/3P salient rotor design have an overlapped winding arrangements between armature coil and field excitation coil that depicts high copper losses as well as results in increased size of motor. Additionally, FEFSM with salient structure of the rotor have high flux strength in the stator-core that has much impact on high iron losses. Copper consumption and iron loss being a crucial proportion in total machine losses. Therefore a novel topology of single phase modular rotor field excited FSM with 8S/6P configuration is proposed, which enable non-overlap arrangement between armature coil and FEC winding that facilitates devaluation in the copper losses. The proposed modular rotor design acquires reduced iron losses as well as reduced active rotor mass comparatively to conventional rotor design. It is very persuasive to analyze the best range of speed for these rotors to avoid cracks and deformation, the maximum tensile strength (can be measured with principal stress in research) of the rotor analysis is conducted using JMAG. A deterministic optimization technique is used to enhance the performance of 8S/6P modular rotor design. The electromagnetic performance of conventional sub-part rotor design, F1-A3-3P design and proposed novel-modular rotor design are analyzed by 3D-Finite Element Analysis (3D-FEA), includes flux linkage, flux distribution, flux strength, back-EMF, cogging torque, torque characteristics, iron losses and efficiency.

The space time fractional Korteweg-de Vries equation, modified Equal Width equation and Benney-Luke Equations are solved by using simple hyperbolic tangent Ansatz method. A simple compatible wave transformation in one dimension is employed to reduce the governing equations to integer ordered ODEs. Then, the ansatz approximation is used to derive exact solutions. Some illustrative examples are presented for some particular choices of parameters and derivative orders.

An expansion method based on time fractional Sine-Gordon equation is implemented to construct some real and complex valued exact solutions to the Korteweg-de Vries and modified Korteweg-de Vries equation in time fractional forms. Compatible fractional traveling wave transform plays a key role to be able to apply homogeneous balance technique to set the predicted solution. The relation between trigonometric and hyperbolic functions based on fractional Sine-Gordon equation allows to form the exact solutions with multiplication of powers of hyperbolic functions.

All empirical water column correction methods have consistently been reported to require existing depth sounding data for the purpose of calibrating a simple depth retrieval model; they yield poor results over very bright or very dark bottoms. In contrast, we set out to (i) use only the relative radiance data in the image along with published data, and several new assumptions, (ii) in order to specify and operate the simplified radiative transfer equation (RTE), (iii) for the purpose of retrieving both the satellite derived bathymetry (SDB) and the water column corrected spectral reflectance over shallow seabeds. Sea truth regressions show that SDB depths retrieved by the method only need tide correction. Therefore it shall be demonstrated that, under such new assumptions, there is no need (i) for formal atmospheric correction, (ii) nor for conversion of relative radiance into calibrated reflectance , (iii) nor for existing depth sounding data, to specify the simplified RTE and produce both SDB and spectral water column corrected radiance ready for bottom typing. Moreover, the use of the panchromatic band for that purpose is introduced. Altogether, we named this process the Self-Calibrated Supervised Spectral Shallow-sea Modeler (4SM). This approach requires a trained practitioner, though, to produce its results within hours of downloading the raw image. The ideal raw image should be a “near-nadir” view, exhibit homogeneous atmosphere and water column, include some coverage of optically deep waters and bare land, and lend itself to quality removal of haze, atmospheric adjacency effect, and sun/sky glint.

The three dimensional conformable time fractional Kadomtsev-Petviashvili and the conformable time fractional modified Kawahara equations are solved by implementing the Kudryashov's procedure. The corresponding wave transformation reduces both equations to some ODEs. Balancing the nonlinear and the highest order derivative terms gives the structure of the solutions in the finite series form. The useful symbolic tools are used to solve the resultant algebraic systems. The solutions are expressed in explicit forms.

Effective solar forecasting has become a critical topic in the scholarly literature in recent years due to the rapid growth of photovoltaic energy production worldwide and the inherent variability of this source of energy. Due to the technological and econonomic limitations of energy storage solutions, using other, mosty conventional, sources to cover energy shortfalls and at the same time utilising solar surpluses production becomes necessary. The need to optimize energy systems, ensuring power continuity, and balancing energy supply and demand has led to the development of various forecasting methods and approaches based on meteorological data or photovoltaic plant characteristics. This article presents the results of a meta-review of the solar forecasting literature, including the current state of knowledge and methodological discussion. It presents a comprehensive set of forecasting methods, evaluates current classifications, and proposes a new synthetic typology. The article emphasizes the increasing role of artificial intelligence (AI) and machine learning (ML) techniques in improving forecast accuracy, alongside traditional statistical and physical models. It explores the challenges of hybrid and ensemble models, which combine multiple forecasting approaches to enhance performance. The paper addresses the emerging trends in solar forecasting research, such as the integration of big data and advanced computational tools. Additionally, from a methodological perspective, the article outlines a rigorous approach to the meta-review research procedure, addresses the scientific challenges associated with conducting bibliometric research, and highlights best practices and principles. This includes defining research questions, selecting eligibility criteria, literature search, data extraction, synthesis, and assessing bias and quality. The article contributes to the solar forecasting field by providing up-to-date knowledge, along with insights on the emerging trends, future research directions, and anticipating implications for the theory and practicce.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

The Suter curves for Wh and Wm characteristics of collected and the first time presented Four-quadrant (4Q) diagrams of 11 radial pump-turbine models with different specific speeds (nq=24.34, nq=24.8, nq=27, nq=28.6, nq=38, nq=41.6, nq=41.9, nq=43.83, nq=50, nq=56, and nq=64.04) are given in the paper, as well as the Suter curves for 2 pump models (nq=25, and nq=41.8) which were already published in the literature. These 11+2 curves were analyzed to establish a certain universal law of behavior in dependence on the specific speed. For the determination of existing laws in behavior, the fitting procedure using the Regression and Spline methods was used. The paper presents a research plan and structures that include: data collection of four-quadrant diagrams for models of pump-turbines and pumps with different specific speeds (nq), the procedure of recalculation of Four-quadrant diagrams of the models into Suter curves for Wh and Wm characteristics, the definition of the optimal point for the pump and turbine operating mode in pump-turbine models for different specific speeds, and developing numerical models in the MATLAB program to obtain the Universal Equation for the Wh and Wm characteristics. The scientific contribution of this paper is the firstly published original mathematical curve named Universal Equation for the Wh and Wm characteristics for radial pumps and pump-turbines. Application of the equation has been demonstrated at the pumping station where two radial pumps are installed. The calculation of transient processes was performed using the numerical model developed by the authors in the mathematical program MATLAB. Comparison of the transition process results has been made for the two cases - when input data in the numerical model have been firstly used with the values of Suter curves for Wh and Wm characteristics obtained by recalculation from the Four-quadrant operating characteristics (Q11, n11, M11) of model’s specific speed, and then secondly with the values of the Suter curves for Wh and Wm characteristics obtained from the Universal Equation.

One of the uses of Helmholtz resonators is as sound absorbers for room acoustic applications, especially for the low frequency range. Their efficiency is centered around their resonance frequency which is mainly depended on elements of their geometry such as the resonator volume and neck dimensions. Incorporating additional necks on the body of a Helmholtz resonator (depending on whether they are open or closed) has been found to alter the resulted resonance frequency. For this study, tunable Helmholtz resonators to multiple resonance frequencies, are proposed and investigated utilizing additional necks. The resonance frequencies of various multi-neck Helmholtz resonators are first modeled with the use of finite element method (FEM), then calculated with the use of an analytical approach and the results of the two approaches are finally compared. Results of this study show that Helmholtz resonators with multiple resonances at desired frequencies are achievable with the use of additional necks, while FEM and analytical methods can be used for the estimation of the resonance frequencies. Analytical and FEM approach results show a good agreement in cases of small number of additional necks, while the increasing differences in cases of higher neck additions, were attributed to the change in effective length of the necks as demonstrated by FEM. The proposed approach can be useful for tunable sound absorbers for room acoustics applications according to the needs of a space. Also, this approach can be applied in cases of additional tunable air resonances of acoustic instruments (e.g. string instruments).

Energy transition is a major structural change in the whole social system, and the energy system must be changed globally to replace fossil fuels. Hydropower is one of the largest renewable energy in the world. However the involuntary resettlees due to the construction of hydropower projects are suffering from being far away from their native land, losing the land cultivated for generations and the houses they live in, and losing the social relationship network based on geography and blood ties. Based on the system evaluation theory of reservoir resettlement and referring to relevant research findings, this paper constructs a comprehensive evaluation index framework for assessing the implementation effect of the PostRelocation Support (PReS) policy. The research region is located in Zhijin County, Bijie City, Guizhou Province, China. Accordingly, a combined method of a structural equation model and a fuzzy comprehensive evaluationary model is used in this paper to analyze the implementation of the PReS policy. The results show that the total score of implementing effects of the PReS policy is 4.4, with dramatic significance. The subindex scores of the resettlers’ family income, living conditions, and production conditions; the local economy; and social stability are 4.3, 4.6, 4.4, 4.6, and 4.3, respectively, with dramatic significance. This paper has analyzed and summarized the successful practices of implementing the PReS policy for reservoir resettlers in three dimensions: poverty alleviation, beautiful home construction and accelerating rural revitalization. Research shows that China's rural reservoir resettlers' PReS policy has been more effective in restoring the livelihoods of reservoir resettlers.

This paper presents an approach to the elastic analysis of beams subjected to Saint-Venant torsion using Green’s theorem and the finite difference method (FDM). The Saint-Venant torsion of beams, also called free torsion or unrestrained torsion, is characterized by the absence of axial stresses due to torsion; only shear stresses are developed. A solution to this torsion problem consists of finding a stress function that satisfies the governing equation and the boundary conditions. The FDM is an approximate method for solving problems described with differential equations; it does not involve solving differential equations, equations are formulated with values at selected nodes of the structure. In this paper, the beam’s cross-section was discretized using a two-dimensional grid and additional nodes were introduced on the boundaries. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary conditions. Beams with solid sections as well as multiply connected cross-sections were analyzed using this model; shear stresses and localized stresses at reentrant corners, torsion constant, and warping displacements were determined. Furthermore, beams with thin-walled closed sections, single-cell or multiple-cell, were analyzed using the Prandtl stress function whereby a linear distribution of the shear stresses over the thickness was considered; closed-form solutions for shear stresses and torsion constant were derived. The results obtained in this study showed good agreement with the exact results for rectangular cross-sections, and the accuracy was increased through a grid refinement. For thin-walled closed sections, the shear stresses obtained at the centerline using the closed-form solutions were in agreement with the values using Bredt’s analysis but the maximal values in the cross-section, which did not necessarily occur at the position with the smallest thickness, were higher; in addition, the results using the closed-form solutions were in good agreement with those using FDM.

The Multi-Level Model (=MLM) was suggested by A. Levichev as a description of quarks and gluons. The review recalls MLM-terminology while MLM-findings (for quarks and leptons) are compared to the theoretical and experimental data as accepted by the Standard Model (=SM). MLM is based on Segal’s compact space-time U(2) and on the sequence of embeddings: U(2) into U(3), U(2) into U(4), etc. These groups were called the levels (of matter): U(2) - the 0th (that is, our mundane world), U(3) - the 1st, U(4) - the 2nd, etc. Such a convention matches the SM-quarks' generations list. Each SM-quark is viewed either as a sunken proton, or as a captured proton. The MLM-proton is elementary and indestructible (hence no need for confinement). For MLM-quarks, in terms of the notion of a ruling group, flavor and color are defined mathematically. The number of colors (and of flavors) is level-dependent. For levels U(3) through U(6) the correspondence with the SM-quarks is established. Three new quarks and two new leptons are predicted. The SM-puzzle of quark and lepton generations is solved. Using the Han-Nambu scheme, the notion of the quark’s electric charge is expressed in terms of color charges. The original part of the review suggests studying the proton’s properties (like mass, shape and inner pressure) on the ba-sis of its wave function.

Demographic change is leading to the aging of German society. As long as the baby boom co-horts are still of working age, the working population will also age - and decline as soon as this baby boom generation gradually reaches retirement age. At the same time, there has been a trend towards increasing absenteeism (times of inability to work) in companies since the zero years, with the number of days of absence increasing with age. We present a novel stochastic forecast approach that combines population forecasting with forecasts of labor force participation trends, considering epidemiological aspects. For this, we combine a stochastic Monte Carlo-based cohort-component forecast of the population with projections of labor force participation rates and morbidity rates. This article examines the purely demographic effect on the economic costs associated with such absenteeism due to the inability to work. Under expected future employment patterns and constant morbidity patterns, absenteeism is expected by close to 5 percent by 2050 relative to 2020, associated with increasing economic costs of almost 3 percent. Our results illustrate how strongly the pronounced baby boom/ baby bust phenomenon determines demographic development in Germany in the midterm.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

This paper presents a robust and efficient fault detection and diagnosis framework for handling small faults and oscillations in synchronous generator (SG) systems. The proposed framework utilizes the Brunovsky form representation of nonlinear systems to mathematically formulate the fault detection problem. A differential-flatness model of SG systems is provided to meet the conditions of the Brunovsky form representation. A combination of high-gain observer and group method of data handling neural network is employed to estimate the trajectory of the system and to learn/ approximate the fault and uncertainties associated functions. The fault detection mechanism is developed based on output residual generation and monitoring so that any unfavourable oscillation and/or fault occurrence can be detected rapidly. Accordingly, an average L1-norm criterion is proposed for rapid decision making of faulty situations. The performance of the proposed framework is investigated for two benchmark scenarios which are actuation fault and fault impact on system dynamics. The simulation results demonstrate the capacity and effectiveness of the proposed solution for rapid fault detection and diagnosis in SG systems in practice, and thus enhancing service maintenance, protection, and life cycle of SGs.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

This article deals with the conformable double Laplace transforms and their some properties with examples and also the existence Condition for the conformable double Laplace transform is studied. Finally, in order to obtain the solution of nonlinear fractional problems, we present a modified conformable double Laplace that we call conformable double Laplace decomposition methods (CDLDM). Then, we apply it to solve, Regular and singular conformable fractional coupled burgers equation illustrate the effectiveness of our method some examples are given.

Search for periodic signals from blazars has become widely discussed topic in recent years. This is because periodic signals bear imprints of the processes occurring near the innermost regions of blazars which are mostly inaccessible to our direct view. Such signals provide insights into various aspect of blazar studies including disk-jet connection, magnetic field configuration and, more importantly, strong gravity near the supermassive black holes and release of gravitational waves from the binary supermassvie black hole systems. In this work, we report detection of a periodic signal in the radio light curves of the blazar J1043+2408 spanning ~10.5 years. We performed multiple methods of time series analysis, namely, epoch folding, Lomb-Scargle periodogram, and discrete auto-correlation function. All three methods consistently reveal a repeating signal with a periodicity of ~563 days. To robustly account for the red-noise processes usually dominant in the blazar variability and other possible artifacts, a large number of Monte Carlo simulations were performed. This allowed us to estimate a high significance (99.9% local and 99.4% global) against possible spurious detection. As possible explanations, we discuss a number of scenarios including binary supermassive black hole system, Lense-Thirring precession, and jet swing and precession.

The Sine-Gordon expansion method is implemented to construct exact solutions some conformable time fractional equations in Regularized Long Wave(RLW)-class. Compatible wave transform reduces the governing equation to classical ordinary differential equation. The homogeneous balance procedure gives the order of the predicted polynomial-type solution that is inspired from well-known Sine-Gordon equation. The substitution of this solution follows the previous step. Equating the coefficients of the powers of predicted solution leads a system of algebraic equations. The solution of resultant system for coefficients gives the necessary relations among the parameters and the coefficients to be able construct the solutions. Some solutions are simulated for some particular choices of parameters.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete break-down of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit (Q²) and the standard deviation (σ) of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol (N=3386 test molecules) for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol (N=1791) for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol (N=373) for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K (N=2637) for the entropy of fusion and 0.5804 and 32.79 J/mol/K (N=2643) for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules, for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation coefficient R² of 0.6066.

Exact solutions to conformable time fractional (3+1)- dimensional equations are derived by using the modified form of the Kudryashov method. The compatible wave transformation reduces the equations to an ODE with integer orders. The predicted solution of the finite series of a rational exponential function is substituted into this ODE. The resultant polynomial equation is solved by using algebraic operations. The method works for the Jimbo-Miwa, the Zakharov-Kuznetsov and the modified Zakharov-Kuznetsov equations in conformable time fractional forms. All the solutions are expressed in explicit forms.

One of the most significant challenges that is facing urban-planning ,is the develop-ment of a transportation network, particularly in historical Syrian cities, which are characterized by their compact urban form. Historical Syrian cities, including historical city of Aleppo, present difficulties due to the essential balance required between saving cultural heritage and meeting the needs of a present-day population. This study basically addresses the city's key elements and planning issues, including traffic density, pedestrian safety, and the massive spreading of motor-ized vehicles. The objective of this study is to analyze the street structure, understanding its components and problems in order to develop a methodology that can be used to enhance urban mobility and to improve the structure of the historical city. for this purpose, two main methods were employed, method of analyzing geographical data based on Geographic Information Systems (GIS) and K-Means cluster analysis method. These two methods were employed to gain detailed and clear vision into mobility patterns of historical Aleppo. Which involved careful processing of data, such as street names, locations, components, quantities, and widths, based on the author’s observations and notes and a variety of local and international sources. This analysis process will not only reveal the current hierarchy of streets but also demonstrates the dynamical and complicated formation of transportation structures of the historical city. The findings of the study describe the challenges faced by historic city centers and highlight the interrelationship between the following: urban structure, objects of cultural heritage, tourism plans, and mobility patterns. The application of spatial analysis method serves as a technique that reveals the formulation of possible scenarios that helps to develop the transportation structure in the historical city of Aleppo. These generated scenarios will be used as typical solutions that can be generalized to all similar historic Syrian cities.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

We discuss two queueing-inventory systems with catastrophes in the warehouse. Catastrophes occur according to Poisson process and upon arrival of a catastrophe all inventory in the system is instantly destroyed. But consumer customers in the system (in the server or in the buffer) continue still waiting for the replenishment of the stock. The arrivals of the consumer customers follow a Markovian Arrival Process (MAP) and they can be queued in an infinite buffer. Service time of a consumer customer follows a phase-type distribution. The system receives negative customers whose have Poisson flows to service facility and upon arrival of a negative customer one consumer customer is pushed out from the system, if any. One of two replenishment policies can be used in the system: either (s,S) or (s,Q). If upon arrival of the consumer customer, the inventory level is zero, then according to the Bernoulli scheme, this customer is either lost (lost sale scheme) or join the queue (backorder sale scheme). The system is formulated by a four-dimensional continuous-time Markov chain. Steady state distribution is obtained using the matrix-geometric method. A comprehensive numerical study is performed on the performance measures under various replenishment policies. Finally, an optimization study is presented.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

Since the come up in the 70´s, various decentralized control methodologies have been developed to deal with the challenge of controlling complex and/or spatially distributed systems with multiple inputs and multiple outputs (MIMO), e.g., chemical plants, power systems, water systems, etc. In general, the use of distributed information and control structures requires to synthesize control laws in a constrained (decentralized) information structure. The article presents another version of the unified frequency domain robust decentralized controller design method [1]. The proposed design procedure is appropriate for uncertain dynamic MIMO systems given as a set of transfer function matrices. Its main framework is provided by the Equivalent Subsystems Method [1, 24] guaranteeing fulfillment of the necessary and sufficient stability condition of the overall closed-loop system if individual closed-loop equivalent subsystems are stable. Generating sets of equivalent subsystems for all transfer function matrices describing the uncertain MIMO plant allows to use the QFT method [19] to independently design local robust SISO controllers that constitute the resulting decentralized controller implemented on true subsystems. The developed design procedure is verified and illustrated on a case study on robust decentralized level controller design for a quadruple tank process [2, 24].

In this paper, we design two inertial-type subgradient extragradient algorithms with line-search process for solving the pseudomonotone variational inequality problems (VIPs) and common fixed-point problem (CFPP) of finite Bregman relatively nonexpansive mapping and a Bregman relatively demicontractive mapping in p-uniformly convex and uniformly smooth Banach spaces, which are more general than Hilbert spaces. Under mild conditions, we derive weak and strong convergence of the suggested algorithms to a common solution of the VIPs and CFPP, respectively. Additionally, an illustrated example is furnished to back up the feasibility and implementability of our proposed methods.

This article analyzes and compares the integration of two different maximum power point tracking (MPPT) control methods, which are tested under partial shading and fast ramp conditions. These MPPT methods are designed by Improved Particle Swarm Optimization (IPSO) and a combination technique between Neural Network and Perturb & Observe method (NN_P&O). These two methods are implemented and simulated for photovoltaic systems (PV), where various system responses, such as: voltage and power are obtained. The MPPT techniques were simulated using Matlab/Simulink environment. A comparison of the performance of IPSO and NN_P&O algorithms is carried out to confirm the best accomplishment of the two methods in terms of speed, accuracy and simplicity.

Tissue engineering has the potential for repairing large bone defects, which impose a heavy financial burden on the public health. However, difficulties with O₂ delivery to the cells residing in the interior of tissue engineering scaffolds make it challenging to grow artificial tissues of clinically-relevant sizes. This study uses image-based simulation in order to provide insight into how to better optimize the scaffold manufacturing parameters, and the culturing conditions, in order to resolve the O₂ bottleneck. To do this, high resolution 3D X-ray images of two common scaffold types (salt leached foam and non-woven fiber mesh) are fed into a Lattice Boltzmann Method fluid dynamics and reactive Lagrangian Scalar Tracking mass transfer solvers. The obtained findings indicate that the scaffolds should have maximal surface area-to-solid volume ratios, for higher chances of the molecular collisions with the cells. Furthermore, the cell culture media should be flown through the scaffold pores as fast as practically possible (without detaching or killing the cells). Finally, we have provided a parametric sweep that maps how the molecular transport within the scaffolds is affected by variations in rates of O₂ consumption by the cells. Ultimately, the results of this study are expected to benefit the computer-assisted design of tissue engineering scaffolds and culturing experiments.

The article analyzes the problems connected with ensuring the coordinated operation of slipway drives that arise during the launch of a ship. The dynamic model of load of the electric drive of the ship's cart is obtained taking into account the peculiarities of the construction of the ship-lifting complex, which allows to analyze the influence of external factors and random influences during the entire process of launching the ship. A linearized mathematical model of the dynamics of a complex vessel movement in the process of descent in the space of states is developed, which allows to identify the mode of operation of the multi-drive system, taking into account its structure. The analysis of efficiency of application of recurrent methods of identification (stochastic approximation and least squares) of the parameters of the linearized model in the space of states is carried out. A decision support system has been developed in the automated system of operational control by the module for estimating the situation and the control synthesis to ensure a coherent motion of a complex ship-carts object in a two-phase environment.

This paper develops Bayesian inference in reliability of a class of scale mixtures of log-normal failure time (SMLNFT) models with stochastic (or uncertain) constraint in their reliability measures. The class is comprehensive and includes existing failure time (FT) models (such as log-normal, log-Cauchy, and log-logistic FT models) as well as new models that are robust in terms of heavy-tailed FT observations. Since classical frequency approaches to reliability analysis based on the SMLNFT model with stochastic constraint are intractable, the Bayesian method is pursued utilizing a Markov chain Monte Carlo (MCMC) sampling based approach. This paper introduces a two-stage maximum entropy (MaxEnt) prior, which elicits a priori uncertain constraint and develops Bayesian hierarchical SMLNFT model by using the prior. The paper also proposes an MCMC method for Bayesian inference in the SMLNFT model reliability and calls attention to properties of the MaxEnt prior that are useful for method development. Finally, two data sets are used to illustrate how the proposed methodology works.

The exact solutions of some conformable time fractional PDEs are presented explicitly. The modified Kudryashov method is applied to construct the solutions to the conformable time fractional Regularized Long Wave-Burgers (RLW-Burgers, potential Korteweg-de Vries (KdV) and clannish random walker's parabolic (CRWP) equations. Initially, the predicted solution in the finite series of a rational form of an exponential function is substituted to the ODE generated from the conformable time fractional PDE by using wave transformation. The coefficients used in the finite series are determined by solving the algebraic system derived from the coefficients of the powers of the predicted solution.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

The complexity of modern power grids, exacerbated by integrating diverse energy sources, espe-cially inverter-based resources (IBRs), presents a significant challenge to grid operation and plan-ning since linear models fail to capture the intricate IBR dynamics. This study employs the Sparse Identification of Nonlinear Dynamics (SINDy) method to bridge the gap between theoretical un-derstanding and practical implementation in power system analysis. It introduces the novel Volterra-based Nonlinearity Index (VNI) to examine system-level nonlinearity comprehensively. The distinction of dynamics into first-order linearizable terms, second-order nonlinear dynamics, and third-order noise elucidates the intricacy of power systems. The findings demonstrate a fundamental shift in system dynamics as power sources transit to IBRs, revealing system-level nonlinearity compared to module-level nonlinearity in conventional syn-chronous generators. The VNI quantifies nonlinear-to-linear relationships, enriching our comprehension of power system behavior and offering a versatile tool for distinguishing between different nonlinearities and visualizing their distinct patterns through the proposed VIN profile.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

For the in-house validation of a droplet digital PCR method, a factorial experimental design was implemented. This design serves different purposes. On the one hand, it is an efficient design in relation to the workload involved in achieving a desirable level of reliability of variance estimates. On the other hand, it allows a partitioning of total variance into different components, thus providing information regarding the dominant sources of random variation. The statistical modelling reflects the actual measurement mechanism, establishing relationships between nominal target DNA copies per well, the range of variation of copy numbers per droplet, probability of detection values, and estimated numbers of copies.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

One of the biggest challenges in characterizing 2-D image topographies is finding a low-dimensional parameter set that can succinctly describe, not so much image patterns themselves, but the nature of these patterns. The 2-D Cluster Variation Method (CVM), introduced by Kikuchi in 1951, can characterize very local image pattern distributions using configuration variables, identifying nearest-neighbor, next-nearest-neighbor, and triplet configurations. Using the 2-D CVM, we can characterize 2-D topographies using just two parameters; the activation enthalpy and the interaction enthalpy. Initial investigations with two different representative topographies (``scale-free-like'' and ``rich club-like'') produce interesting results when brought to a CVM free energy minimum. Additional phase space investigations, where one of these two parameters has been set to zero, identify useful parameter ranges. Careful comparison of the analytically-predicted configuration variables versus those obtained when performing computational free energy minimization on a 2-D grid show that the computational results differ significantly from the analytic solution. The 2-D CVM can potentially function as a secondary free energy minimization within the hidden layer of a neural network, providing a basis for extending node activations over time and allowing temporal correlation of patterns.

We have considered a SEIR-SEI Vector-host mathematical model which captures malaria transmission dynamics, described and built on 7-dimensional nonlinear ordinary differential equations. We compute the basic reproduction number of the model; examine the positivity and boundedness of the model compartments in a region using well established methods viz: Cauchy’s differential theorem, Birkhoff & Rota’s theorem which verifies and reveals the well-posedness, and carrying capacity of the model respectively, the existence of the Disease-Free (DFE) and Endemic (EDE) equilibrium points were determined and examined. Using the Gaussian elimination method and the Routh-hurwitz criterion, we convey stability analyses at DFE and EDE points which indicates that the DFE (malaria-free) and the EDE (epidemic outbreak) point occurs when the basic reproduction number is less than unity (one) and greater than unity (one) respectively. We obtain a solution to the model using the Variational iteration method (VIM) (an unprecedented method) to each population compartments and verify the efficacy, reliability and validity of the proposed method by comparing the respective solutions via tables and combined plots with the computer in-built Runge-kutta-Felhberg of fourth-fifths order (RKF-45). We illustrate the combined plot profiles of each compartment in the model, showing the dynamic behavior of these compartments; then we speculate that VIM is efficient and capable to conduct analysis on Malaria models and other epidemiological models.

The city-port involves a decisive reality for the economic development of the territories and nations, capable of significantly influencing the conditions of well-being and quality of life, and of making the Circular City Model operational, preserving and enhancing seas and marine resources in a sustainable way, through the construction of appropriate production and consumption models, with attention to relations with the urban and territorial system. The Circular Economy paradigm identifies the ideal context in the city-port to rethink traditional development models and make ports driver areas for the regeneration of the city and metropolitan territories, in compliance with the EU Directive 2014/89 which considers maritime spatial planning as a tool for public authorities and stakeholders to achieve an integrated approach, promoting the development of maritime and coastal economies and the sustainable use of resources. The paper, starting from these assumptions, presents an adaptive decision-making process for the strategies development of the Naples (Italy) commercial port, aimed at re-establishing a sustainable city-port relationship and making operative Circular Economy principles.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

In this paper, we introduce a new formulation based on Floquet (Fourier) spectral analysis combined with a spectral modulation technique (and its spatial form) to study strongly coupled sublattices predefined in the infinite and large finite extent of almost periodic antenna arrays (e.g metasurfaces). This analysis is very relevant for dense massive MIMO, intelligent surfaces, 5G, and 6G applications (used for very small areas with a large number of elements such as millimeter and terahertz waves applications). The numerical method that is adopted to model the structure is the method of moments simplified by equivalent circuits MoM GEC. Other numerical methods (as the ASM array scanning method and windowing Fourier method) used this analysis in their kernel that to treat periodic and pseudo-periodic (or quasi-periodic) arrays.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

Rodents are known to be reservoirs of Toxoplasma gondii and keep the parasite circulation in the environment. We conducted biomonitoring to assess the role of sylvatic rodents in maintaining T. gondii and to analyse the prevalence and seroprevalence of the parasite in seven wild rodent species. Rodents were collected in our study sites (woodland and open grasslands) located in northeastern Poland and dissected. We collected brain, spleen, blood and serum samples. We applied both molecular (PCR assay, nested-PCR assay) and serological (ELISA and agglutination tests) methods to indicate the best approach for application in the biomonitoring of T. gondii in small mammals. We screened samples from 95 individuals sing PCR assays and found no T. gondii DNA. The agglutination test showed no signal. We found antibodies against T. gondii in 6 sera samples out of 74 analysed (seroprevalence = 8.11% [4.0-17.1]). Our results confirm that rodents participate in the life cycle of T. gondii as reservoirs of this parasite in the sylvatic environment. However, biomonitoring should be performed with the ELISA tests to search for T. gondii antigens, rather than a molecular approach only.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

Durability monitoring of insecticide-treated nets (ITNs) containing a pyrethroid in combination with a second active ingredient (AI) must be adapted so that the insecticidal bioefficacy of each AI can be monitored independently. An effective way to do this is to measure rapid knock down of a pyrethroid-susceptible strain of mosquitoes to assess the bioefficacy of the pyrethroid component and to use a pyrethroid-resistant strain to measure the bioefficacy of the second ingredient. To allow robust comparison of results across tests within and between test facilities, and over time, protocols for bioefficacy testing must include either characterisation of the resistant strain, standardisation of the mosquitoes used for bioassays, or a combination of the two. Through a series of virtual meetings, key stakeholders and practitioners explored different approaches to achieving these goals. Via an iterative process we decided on the preferred approach and produced a protocol consisting of characterising mosquitoes used for bioefficacy testing before and after a round of bioassays, for example at each time point in a durability monitoring study. We present the final protocol and justify our approach to establishing a standard methodology for durability monitoring of ITNs containing pyrethroid and a second AI.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

According to the current European and Italian scenario related to urban re-generation, cultural and landscape heritage, valorisation is being also enhanced by the activation of innovative processes. These involve the development of methodologies and tools that are able to address decision-making processes among low entropy economy, complex values and creative practices. In this perspective, the research aims to investigate the possibilities of developing a Cultural Heritage Low Entropy Enhancement (CHLEE) approach by considering how the complex values of cultural heritage can vary not only through a physical transformation of spaces but also through a program of uses and activities able to produce new values, where the human experience is essential. This type of model modifies the objectives that characterise the valorisation of cultural heritage and landscape, recognising that the fruition is no longer “consumerist” but “experiential”. A crucial role is represented by the heterogeneity of creative practices that contribute to the identificationidentifying and implementation ofimplementing innovative management and governance models. The present paper explores the components of creative regenerative processes, based upon the ex-post evaluation of some Italian experiments, across the PROMETHEE-GAIA multi-criteria method, to understand how creative experiences are building innovation ecosystem thanks to low entropy economy and improve the ex-ante evaluation for new strategies and policies.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

This paper presents an approach to the two-dimensional analysis of elastic isotropic deep beams using the finite difference method (FDM). Deep beams are subjected to in-plane loading and present a shear span to height ratio of less than 2.50; consequently, Euler-Bernoulli beam theory and Timoshenko beam theory do not apply. Deep beams analysis is generally conducted using numerical methods such as the finite element method and to a lesser extent the FDM; the strut-and-tie model and the stress field method are also widely utilized. Analytical approaches usually make use of the Airy stress function, where stresses are formulated in terms of the stress function; however, the exact solution of this function satisfying all of the boundary conditions can hardly be found, even for simple cases. In this paper, deep beams were analyzed using the FDM. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected nodes of the structure. Therefore, the deep beam was discretized with a two-dimensional grid, and additional nodes were introduced at the boundaries and at positions of discontinuity (openings, brutal change of material properties, non-uniform grid spacing), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary and continuity conditions. An Airy stress function approach and a displacement potential function approach were considered in this study whereby strong formulations of equations (equilibrium, kinematic, and constitutive) were set. Stress and stability analyses were carried out with this model; furthermore, deep beams of varying stiffness, layered beams, and beams having openings were analyzed. For slender beams, the results obtained with the Airy stress function approach showed good agreement with those of the Euler-Bernoulli beam theory, and for deep beams, the shapes of stress distributions were in good agreement with a proper understanding of the behavior of structures. On the other hand, the displacement potential function approach delivered unsatisfactory results, probably due to the use of an inefficient equation solver; a more powerful tool will be needed in future research for this purpose.

In the implementation of thermal enhanced oil recovery (TEOR) techniques, the temperature impact on relative permeability in oil - water systems is of special concern. Hence, developing a fast and reliable tool to model the temperature effect on two-phase oil - water relative permeability is still a major challenge for precise studying and evaluation of TEOR processes. To reach the goal of this work, two promising soft-computing algorithms, namely Group Method of Data Handling (GMDH) and Gene Expression Programming (GEP) were employed to develop reliable, accurate, simple and quick to use paradigms to predict the temperature dependency of relative permeability in oil - water systems (K_rw and K_ro). To do so, a large database encompassing wide-ranging temperatures and fluids/rock parameters, including oil and water viscosities, absolute permeability and water saturation, was considered to establish these correlations. Statistical results and graphical analyses disclosed the high degree of accuracy for the proposed correlations in emulating the experimental results. In addition, GEP based correlations were found to be the most consistent with root mean square error (RMSE) values of 0.0284 and 0.0636 for K_rw and K_ro, respectively. Lastly, the comparison of the performances of our correlations against those of the preexisting ones indicated the large superiority of the introduced correlations compared to previously published methods. The findings of this study can help for better understanding and studying the temperature dependency of oil - water relative permeability in thermal enhanced oil recovery processes.

The electrical motor design requires a lot of work and resources. In the field, motor designers need to decide on competitive motor sizing quickly to compete with other motor suppliers. Generally, it requires expensive FEM S/W to get accurate motor sizing results, but buying and maintaining many licenses is costly. Moreover, it needs some patience to get the result from FEM analysis. In this paper, the motor sizing technique using an existing production motor is presented to respond to urgent requests from customers without using FEM analysis. In order to enhance the fidelity of the result, magnetic flux loss by magnet coating and non-linear characteristics are considered during the motor sizing process. The proposed sizing method was verified by comparison to the FEM analysis and test result and showed reasonable confidence in them. Also, this method has the substantial advantage of outputting accurate results instantly without taking any time. It helps with the modification design of electrical motors without using expensive FEM S/W and a certain level of skill or experience.

In the face of the upcoming 30th anniversary of econophysics, we review our contributions and other related works on the modeling of the long–range memory phenomenon in physical, economic, and other social complex systems. Our group has shown that the long–range memory phenomenon can be reproduced using various Markov processes, such as point processes, stochastic differential equations and agent–based models. Reproduced well enough to match other statistical properties of the financial markets, such as return and trading activity distributions and first–passage time distributions. Research has lead us to question whether the observed long–range memory is a result of actual long–range memory process or just a consequence of non–linearity of Markov processes. As our most recent result we discuss the long–range memory of the order flow data in the financial markets and other social systems from the perspective of the fractional Lèvy stable motion. We test widely used long-range memory estimators on discrete fractional Lèvy stable motion represented by the ARFIMA sample series. Our newly obtained results seem indicate that new estimators of self–similarity and long–range memory for analyzing systems with non–Gaussian distributions have to be developed.

This study focused on hydrolysis of cosmetic fillers hyaluronic acid (HA) and kinetics of the HA hydrolysis using the homogenate of the red king crab hepatopancreas. Turbidimetric analysis of the reaction mixture revealed a bell-shaped time dependence of aggregation formation. It was shown that the obtained homogenate has the similar activity to the commercially available hyaluronidase. The atomic force microscopy (AFM) examination found that the HA fillers were represented by spherical-like structures. These structures were destroyed under the action of the homogenate of the red king crab hepatopancreas. NMR of the reaction mixture showed that HA degradation lasts for some days, but a maximum rate of the reaction is detected in the first hours of incubation. The preparation with hyaluronidase activity obtained from the red king crab hepatopancreas could be used as potentially safe product for treating filler complications.

Robots in space are necessarily extremely light and lack structural stiffness resulting in natural frequencies of resonance so low as to reside inside the attitude controller’s bandwidth. A variety of input trajectories can be used to drive a controller’s attempt to ameliorate the control-structural interactions where feedback is provided by low-quality, noisy sensors. Traditionally, step functions are used as the ideal input trajectory. However, step functions are not ideal in many applications, as they are discontinuous. Alternative input trajectories are explored in this manuscript and applied to an example system that includes a flexible appendage attached to a rigid main body. The main body is controlled by a reaction wheel. The equations of motion of the flexible appendage, rigid body, and reaction wheel are derived. A feedback controller is developed to account for the rigid body modes. Additional filters are added to compensate for the system’s flexible modes. Sinusoidal trajectories are autonomously generated to feed the controller. Whiplash compensation is additionally implemented for comparison. The control method without random errors with the smallest error is the sinusoidal trajectory method, which showed a 97.39% improvement when compared to the baseline response when step trajectories were commanded, while the sinusoidal method was inferior to traditional step trajectories when sensor noise and random errors were present.

The unresolved territories are privileged places for the proliferation of degradation phenomena that affect the environment and human well-being. The impacts of their critical conditions go beyond the limits of the damaged urban fragments, involving the built environment, society, economy, culture and conditioning quality of life. This paper proposes a methodological approach to landscape design supported by an evaluation framework to orient strategic design planning with specific attention to unresolved territories consistent with circular economy perspective. The circular city principles are applied to spatial planning of landscape, by operationalising Ecosystem Services, Landscape Services, and Ecosystem Disservices, as interpretative categories for multi-dimensional regenerative strategies. Starting from the theoretical framework, the objective of the analysis is to implement an approach to the regenerative design of landscapes of waste, defined wastescapes. The industrial area of East Naples is the case study where an incremental evaluative approach has been defined to design scenarios to provide services and values, aimed to drive the conversion in a regenerativescape. A multi-criteria analysis through PROMETHEE-GAIA method has been implemented to compare the base case scenario with two incremental new scenarios and identify situated sustainable priorities.

During the past two decades of e-commerce growth, the concept of a business model has become increasingly popular. More recently, the research on this realm has grown rapidly, with diverse research activity covering a wide range of application areas. Considering the sustainable development goals, the innovative business models have brought a competitive advantage to improve the sustainability performance of organizations. The concept of the sustainable business model describes the rationale of how an organization creates, delivers, and captures value, in economic, social, cultural, or other contexts, in a sustainable way. The process of sustainable business model construction forms an innovative part of a business strategy. Different industries and businesses have utilized sustainable business models’ concept to satisfy their economic, environmental, and social goals simultaneously. However, the success, popularity, and progress of sustainable business models in different application domains are not clear. To explore this issue, this research provides a comprehensive review of sustainable business models literature in various application areas. Notable sustainable business models are identified and further classified in fourteen unique categories, and in every category, the progress -either failure or success- has been reviewed, and the research gaps are discussed. Taxonomy of the applications includes innovation, management and marketing, entrepreneurship, energy, fashion, healthcare, agri-food, supply chain management, circular economy, developing countries, engineering, construction and real estate, mobility and transportation, and hospitality. The key contribution of this study is that it provides an insight into the state of the art of sustainable business models in various application areas and future research directions. This paper concludes that popularity and the success rate of sustainable business models in all application domains have been increased along with the increasing use of advanced technologies.

This paper attempts to develop a Dynamic Mode Decomposition (DMD) based Reduced Order Model (ROMs) which can quickly but accurately predict the forces and moments experienced by a road vehicle such that they be used by an on-board controller to determine the vehicle's trajectory. DMD can linearize a large dataset of high-dimensional measurements by decomposing them into low-dimensional coherent structures and associated time-dynamics. This ROM then also can be applied to predict the future state of the fluid flow. Existing literature on DMD is limited to low Reynolds number applications. This paper presents DMD analyses of the flow around an idealized road vehicle, called the Ahmed body, at a Reynolds number of 2.7E6. The high dimensional dataset used in this paper was collected from a computational fluid dynamics (CFD) simulation performed using Menter's shear stress transport (SST) turbulence model within the context of Improved Delayed Detached Eddy Simulations (IDDES). The DMD algorithm, as available in literature, was found to suffer nonphysical dampening of the medium-to-high frequency modes. Enhancements to the existing algorithm were explored, and a modified DMD approach is presented in this paper which includes: (a) a requirement of higher sampling rate to obtain higher resolution of data, and (b) a custom filtration process to remove spurious modes. The modified DMD algorithm thus developed was applied to the high Reynolds number, separation dominated flow past the idealized ground vehicle. The effectiveness of the modified algorithm was tested by comparing future predictions of force and moment coefficients as predicted by the DMD-based ROM to the reference CFD simulation data, and found to offer significant improvement.

Urban areas are centres of business and innovation. Freight transport is indispensable for the proper functioning of any modern urban society. Urban areas can’t function without an appropriate freight transport system, due to the need to replenish stocks of food and other goods in retail shops. The complexity of the decisions concerning implementation of measures to improve the movement of goods in the city requires tools designed to support this process. The purpose of this article is to introduce the possibility of applying the Analytic Hierarchy Process (AHP) as well as the Decision Making Trial and Evaluation Laboratory Method (DEMATEL) in choosing a set of measures and in analysing in the field of distribution logistics, which will help to solve the delivery problems and streamline the cargo flows in Szczecin, in the context of sustainable development.

Conclusions: Our findings suggest that the NMS-E represents a valuable preoperative diagnostic tool for endometriosis, effectively correlating with the disease's severity and surgical outcomes. Incorporating the NMS-E into clinical practice could significantly enhance the management of endometriosis by addressing current diagnostic limitations and guiding surgical planning.

We examine data assimilation coupling between meteorology and chemistry in the stratosphere from both weak and strong coupling strategies. The study was performed with the Canadian operational weather prediction Global Environmental Multiscale (GEM) model coupled online with the photochemical stratospheric chemistry developed at the Belgian Institute for Space Aeronomy, described in Part I. Here, the Canadian Meteorological Centre’s operational variational assimilation system was extended to include errors of chemical variables and cross-covariances between meteorological and chemical variables in a 3D-Var configuration, and we added the adjoint of tracer advection in the 4D-Var configuration. Our results show that the assimilation of limb sounding observations from the MIPAS instrument on board Envisat can be used to anchor the AMSU-A radiance bias correction scheme. Also, the added value of limb sounding temperature observations on meteorology and transport is shown to be significant. Weak coupling data assimilation with ozone-radiation interaction is shown to give comparable on meteorology whether a simplified linearized or comprehensive ozone chemistry scheme is used. Strong coupling data assimilation, using static error cross-covariances between ozone and temperature in a 3D-Var context, produced inconclusive results with the approximations we used. We have also conducted the assimilation of long-lived species observations using 4D-Var to infer winds. Our results showed the added value of assimilating several long-lived species, and an improvement in the zonal wind in the Tropics within the troposphere and lower stratosphere. 4D-Var assimilation also induced a correction of zonal wind in the surf zone and a temperature bias in the lower tropical stratosphere

This research aimed to determine the most viable locations for establishing solar energy facilities in Yemen through the utilization of the Analytical Hierarchy Process (AHP), Best-Worst Method (BWM), and Geographic Information System (GIS). A total of twelve key criteria were meticulously selected and evaluated based on their impact on the appropriateness of sites for solar power plants. These criteria were amalgamated using a weighted overlay tool, resulting in a map that classified regions as either optimal, highly suitable, or suitable. The findings of the study indicated that the eastern, southern, and northern parts of Yemen are prime candidates for solar energy installations due to their moderate climate and flat topography. On the other hand, the western regions were deemed less favorable. The breakdown of site classifications revealed that 38% of areas were optimal, 61% were highly suitable, and only 1% were considered suitable, based on the assigned weights from the AHP and BWM methodologies. Moreover, a sensitivity analysis was carried out to evaluate the impact of adjusting the weights of Global Horizontal Irradiance (GHI) and slope on site classifications. A minor increase in the weights of GHI (from 30% to 31%) and slope (from 10% to 11%) resulted in a significant alteration in the suitability categories, highlighting the importance of weight adjustments in multi-criteria decision-making processes. In conclusion, the study emphasizes the effectiveness of AHP, BWM, and GIS in assessing site suitability for solar energy facilities, as well as the significance of sensitivity analyses. These approaches provide valuable insights for decision-makers, aiding in strategic planning and fostering sustainable energy development in Yemen.

A method for estimating river water surface elevation (WSE) from Landsat imagery using the river inundation area - water surface elevation (RIA-WSE) rating curve constructed from the U.S. Geological Survey Topobathymetric Elevation Model (TEM) data was developed and tested at six gauging stations along the upper Mississippi River. The Otsu's automatic threshold selection algorithm was employed for the image classification and estimation of inundation areas within each pre-defined polygon around each gauging station. In addition to the commonly used green-band based water indices, Landsat 8 and 9 OLI's ultra-blue, blue, and red band-based water indices were also tested in this study, which resulted in twenty different water indices: NDWIv (Normalized Difference Water Index), MNDWI1v and MNDWI2v (Modified Normalized Difference Water Index), AWEIsv (Automatic Water Extraction Index with shadow), and AWEInsv (AWEI without shadow), where v represents the visible light band used in the water index. At each station, about 60-80 Landsat 8 or 9 images during 2013-2023 were used for assessing the performances of the twenty water indices through comparing the estimated WSEs with the measured WSEs. Results showed that the ultra-blue or red band-based AWEIs yielded the most accurate estimations of WSEs among the twenty tested water indices.

This comprehensive analysis thoroughly examines the topic of adversarial attacks in artificial intelligence (AI), providing a detailed overview of the various methods used to compromise machine learning models. It explores different attack techniques, ranging from the simple Fast Gradient Sign Method (FGSM) to the intricate Carlini and Wagner Attack (C&W), emphasising the wide range of adversarial approaches and their intended goals. The discussion also distinguishes between targeted and non-targeted attacks, highlighting the adaptability and versatility of these malicious efforts. Additionally, the study delves into the realm of black-box attacks, revealing the capability of adversarial strategies to compromise models even with limited knowledge. Real-life examples illustrate the tangible consequences and potential dangers of adversarial attacks in various fields such as self-driving cars, multimedia, and voice assistants. These cases highlight the difficulties in ensuring the legitimacy and dependability of AI-powered technologies and programs. The article stresses the importance of ongoing research and innovation to address the growing difficulties posed by advanced methods like deepfakes and disguised voice commands in preserving the security of AI systems. This study provides valuable insights on how different adversarial strategies and defence mechanisms interact within AI. The results emphasise the urgent need for stronger and more secure AI models to combat the increasing number of adversarial threats in today's AI landscape. These findings can guide future research and innovations in developing more resilient AI technologies that can better withstand various adversarial vulnerabilities and challenges.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

Socio-ecologic, socio-economic, and socio-technical transitions are opportunities that require fundamental changes in the system. These will encounter matters associated with security, service adoption by end-users, infrastructure and availability. The purpose of this study is to examine and overcome the risks to take advantage of opportunities through the novel Risky-Opportunity Analysis Method (ROAM). A novel quantitative method is designed to determine when, after making some changes, the risks become acceptable so that the opportunity does not deviate from the objectives. The approach provided a quantitative evaluation of the possible changes in parallel with digitization, towards providing a green Service Supply Chain (SSC). The result of ROAM shows that the most cost-effective change to increase the resilience of the system is a solution (SMS) which is different from that identified by a TOPSIS multi-criteria method. Real-word decisions in change management should tackle the complexity of systems and uncertainty of events during and after transition through a careful analysis of the alternatives. A case-study was carried out to evaluate the alternatives of an ancillary service in the Payment Service Providers (PSP). The comparison of the ROAM results with the traditional TOPSIS of the case-study unveils the priority of the ROAM in practice when the alternatives are Risky-Opportunities. The existing risk assessment tools do not take advantage of risky opportunities. To this aim, the current article introduces the term Risky-Opportunity, and two indexes Stress and Strain of the alternatives that are designed to be employed in the new quantitative ROAM approach.

Mereotopology is a concept rooted in analytical philosophy. The phase-field concept is based on mathematical physics and finds applications in materials engineering. The two concepts seem to be disjoint at a first glance. While mereotopology qualitatively describes static relations between things like x isConnected y (topology) or x isPartOf y (mereology) by first order logic and Boolean algebra, the phase-field concept describes the geometric shape of things and its dynamic evolution by drawing on a scalar field. The geometric shape of any thing is defined by its boundaries to one or more neighboring things. The notion and description of boundaries thus provides a bridge between mereotopology and the phase-field concept. The present article aims to relate phase-field expressions describing boundaries and especially triple junctions to their Boolean counterparts in mereotopology and contact algebra. An introductory overview on mereotopology is followed by an introduction to the phase-field concept already indicating first relations to mereo- topology. Mereotopological axioms and definitions are then discussed in detail from a phase-field perspective. A dedicated section introduces and discusses further notions of the isConnected relation emerging from the phase-field perspective like isSpatiallyConnected, isTemporallyConnected, isPhysicallyConnected, isPathConnected and wasConnected. Such relations introduce dynamics and thus physics into mereotopology as transitions from isDisconnected to isPartOf can be described.

This article describes the use of the PI ProcessBook software tool for visualization and indirect monitoring of occupancy of SHC rooms from the measured operational and technical quantities for monitoring of daily living activities for support of independent life of elderly persons. The proposed method for data processing (predicting the CO₂ course using neural networks from the measured temperature indoor T_i (°C), temperature outdoor T_o (°C) and the relative humidity indoor rHi (%)) was implemented, verified and compared in MATLAB SW tool and IBM SPSS SW tool with IoT platform connectivity. Within the proposed method, the Stationary Wavelet Transform de noising algorithm was used to remove the noise of the resulting predicted course. In order to verify the method, two long-term experiments were performed, (specifically from February 8 to February 15, 2015, from June 8 to June 15, 2015) and two short-term experiments (from February 8, 2015 and from June 8, 2015). For the best results of the trained ANN BRM within the prediction of CO₂, the correlation coefficient R for the proposed method was up to 90%. The verification of the proposed method confirmed the possibility to use the presence of persons of the monitored SHC premises for rooms ADL monitoring.

Let β= (((24!)!)!)!, and let {${\mathcal P}_{n^2+1}$} denote the set of all primes of the form {$n^2+1$}. Let ${\mathcal M}$ denote the set of all positive multiples of elements of the set {${\mathcal P}_{n^2+1} \cap (\beta,\infty)$}. The set {${\mathcal X}=\{0,\ldots,\beta\} \cup {\mathcal M}$} satisfies the following conditions: (1) ${\rm card}({\mathcal X})$ is greater than a huge positive integer and it is conjectured that ${\mathcal X}$ is infinite, (2)} we do not know any algorithm deciding the finiteness of ${\mathcal X}$, (3)~a~known and short algorithm for every {$n \in N$} decides whether or not {$n \in {\mathcal X}$}, (4) a known and short algorithm returns an integer~$n$ such that ${\mathcal X}$ is infinite if and only if ${\mathcal X}$ contains an element greater than $n$. The following problem is open: {\em simply define a set {${\mathcal X} \subseteq N$} such that ${\mathcal X}$ satisfies conditions (1)-(4), and \underline{we do not know any representation of~~${\mathcal X}$~~as a finite union of sets whose definitions are simpler than} \underline{the definition of ${\mathcal X}$}} {\tt (5)}. Let {$f(1)=2$}, {$f(2)=4$}, and let {$f(n+1)=f(n)!$} for every integer {$n \geqslant 2$}. For a positive integer $n$, let {$\Psi_n$} denote the following statement: {\em if a system of equations ${\mathcal S} \subseteq \Bigl\{x_i!=x_k: i,k \in \{1,\ldots,n\}\Bigr\} \cup \Bigl\{x_i \cdot x_j=x_k: i,j,k \in \{1,\ldots,n\}\Bigr\}$ has only finitely many solutions in positive integers \mbox{$x_1,\ldots,x_n$}, then each such solution \mbox{$(x_1,\ldots,x_n)$} satisfies {$x_1,\ldots,x_n \leqslant f(n)$}.} We prove that for every statement $\Psi_n$ the bound {$f(n)$} cannot be decreased. The author's guess is that the statements {$\Psi_1,\ldots,\Psi_9$} are true. We prove that the statement $\Psi_9$ implies that the set ${\mathcal X}$ of all {non-negative} integers $k$ whose number of digits belongs to {${\mathcal P}_{n^2+1}$} satisfies conditions {\tt (1)-(5)}.

For evaluating probabilities of arbitrary random events with respect to a given multivariate probability distribution, specific techniques are of great interest. An important two-dimensional high risk limit law is the Gauss-exponential distribution whose probabilities can be dealt with based upon the Gauss-Laplace law. The latter will be considered here as an element of the newly introduced family of (p,q)-spherical distributions. Based upon a suitably defined non-Euclidean arc-length measure on (p,q)-circles we prove geometric and stochastic representations of these distributions and correspondingly distributed random vectors, respectively. These representations allow dealing with the new probability measures similarly like with elliptically contoured distributions and more general homogeneous star-shaped ones. This is demonstrated at hand of a generalization of the Box-Muller simulation method. En passant, we prove an extension of the sector and circle number functions.

The main objective of this communication is to describe the ‘Global Salt Cycle’. Giant salt accumulations are commonly found along continental margins of former rifts. The first stage in the accumulation process is saturation of newly formed oceanic crust with seawater. Final mobilisation and accumulation of the salts occurs during rifting, localised in the vicinity of relict subduction zones. Oceanic crust is created along the spreading ridges in the deep oceans of the Earth. It exchanges mass and energy with seawater in hydrothermal circulation cells that penetrate deep into the new and fractured crust. Water-rock interactions include the formation of hydrated and hydroxylated minerals, e.g., serpentinites and clay minerals. By incorporating hydroxyl groups and water in their crystal lattices, the salinity of remaining brines increases. Subduction of oceanic crust and serpentinised lithosphere transports water, hydrated minerals, and marine salts deep into the crust and mantle. Upon pressurisation and heating of the subducting slab, different parts of this water are expelled at different depths/temperatures. The resulting fluids will contain salts brought in with the slab, as well as new salts formed by water-rock interaction. The combination of elevated pressures and temperatures, water, salinity, and CO2, create permeability in the normally impermeable, peridotitic mantle, by altering the fluid-rock dihedral angles of mineral grains. This P/T-determined intergranular permeability allows ascent of saline fluids, under lithostatic pressure, within the mantle wedge, or the slab itself. The fluids produce a mechanically weakened and buoyant zone within the mantle wedge due to high pore pressure between mineral grains and reduced mantle density. During the lifetime of a subduction zone, a substantial accumulation of saline fluids within the mantle wedge and crust, is evident. Deep, fluid reservoirs accumulate between the subduction trench and the volcanic front. They may exist for hundreds of millions of years, even after the extinction of the subduction zone. Saline fluids may escape to the surface along deep faults, due to overfilling of available pores/fractures. Fluids within the mantle wedge may form rock melts or exist as supercritical, mineral rich fluids. The combination of reduced pressure due to rifting, and a saline and buoyant mantle, creates a mantle circulation that brings the accumulated, saline fluids, to crustal levels. Salts will therefore accumulate during initial stages of rifting as a result of massive fluid expulsion, phase change and boiling of mantle fluids. No extra energy is required to produce phase change and boiling. The result is formation of solid salts or dense brines/slurries invading fractured crustal rocks, or escaping to the surface/seabed. This process may take place both before and after the sea has invaded a continental rift.