Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

This study explores into a comprehensive examination of an optical cavity system that integrates Raman and Yb-doped gain media, with a focus on understanding their interactions. The research implies a characterization of each gain medium within the cavity while subjecting them to diverse co-pumping conditions with the other. When the Raman-lasing cavity is co-pumped by exciting the Yb-doped section, the resulting composite laser exhibits significant threshold reductions and there is an optimal co-pumping regime that enhances energy transfer from pump to Stokes. As for the complementary cavity, where the Yb-doped gain is influenced by the co-pumped Raman gain, at moderate pump powers a light-controlling-light behavior phenomenon arises. Within this regime, the 1064-nm signal suppresses the Yb-generated 1115-nm signal, suggesting potential applications in intracavity optical modulation. For higher pump levels, a cooperative effect emerges whereby both lasers mutually enhance each other. Minor variations in the primary 974-nm pump power, even by just a few milliwatts, result in significant capabilities for switching or modulating the Stokes signal. Under these conditions of mutual enhancement, the hybrid optical system validates notable improvements regarding energy transfer efficiency and threshold reduction. This research provides valuable insights into the intricate dynamics of optical cavity systems and reveals promising avenues for applications in advanced optical modulation technologies.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

Sensors became integrated through the control condition arrangement, either for visual, mechanical, biological, or chemical applications. New stuff is designed for detection, as Diluted Magnetic Semiconductors (DMS), and are considered attractive candidates that consist of a traditional 111- V, II-VI, or group IV semiconductor. Manganese Mn-doped GaN (Mn.Gac.N) epitaxial velum has a unique magnetic, visual and chemical properties in order to control system intelligent for detector design. The subject area of the magnetic properties of MnxGal-xN is on a large scale available, there are only a few studies on the visual properties and electrochemical properties of MnxGal-xN epitaxial velums. Where MnGaN velums were used in spintronic and opto-electronic applications according to their magnetic characterization and constructed MnGaN electrode are drop fabric potential for potentiometric sensor applications since they have good performance as ion-selective electrodes. The electrical and magnetic properties that allow the control of electron spin as well as complaint period, makes the materials ideal for spintronic applications. Designing such spintronic and optoelectronic devices based on MnxGal-xN requires a broader agreement of physical, visual, electrical and chemical properties epitaxial velums that are still seldom in the literature. This bailiwick displays the potential use of MnGaN semiconductor as an all solid-state potentiometric sensor for measuring anions in solutions in the control engineering field.

Magnesium-silver alloys are of high interest for the use as temporary bone implants due to their antibacterial properties in addition to biocompatibility and biodegradability. Thin wires in particular can be used for scaffolding, but the determination of their degradation rate and homogeneity using traditional methods is difficult. Therefore, we have employed 3D imaging using X-ray near-field holotomography with sub-micrometer resolution to study the degradation of thin (250 μm diameter) Mg-2Ag and Mg-6Ag wires. The wires were studied in two states, recrystallized and solution annealed to assess the influence of Ag content and precipitates on the degradation. Imaging was employed after degradation in Dulbecco’s modified Eagle’s medium and 10% fetal bovine serum after 1 to 7 days. At 3 days of immersion the degradation rates of both alloys in both states were similar, but at 7 days higher silver content and solution annealing lead to decreased degradation rates. The opposite was observed for the pitting factor. Overall, the standard deviation of the determined parameters was high, owing to the relatively small field of view during imaging and high degradation inhomogeneity of the samples. Nevertheless, Mg-6Ag in the solution annealed state emerges as a potential material for thin wire manufacturing for implants.

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

Although fragility fractures, osteoporosis, sarcopenia and frailty are becoming more prevalent in our aging society the treatment options are limited and preventative strategies are needed. Despite magnesium being integral bone and muscle physiology the relationship between dietary magnesium and skeletal muscle and bone health has not been investigated concurrently before. We analysed cross-sectional associations between dietary magnesium and skeletal muscle mass (as fat free mass – FFM), grip strength and bone density (BMD) in 156,575 men and women aged 39-72 years from the UK Biobank cohort. FFM was measured with bioelectrical impedance and expressed as the percentage of body weight (FFM%) or divided by body mass index (FFM_BMI). Adjusted mean grip strength, FFM%, FFM_BMI, and BMD were calculated according quintiles of dietary magnesium, correcting for covariates. Significant inter-quintile differences across intakes of magnesium existed in men and women respectively of 1.1% and 2.4% for grip strength, 3.0% and 3.6% for FFM%, 5.1% and 5.5% for FFM_BMI, and 2.9% and 0.9% for BMD. These associations are as great or greater than annual measured losses of these musculoskeletal outcomes indicating potential clinical significance. Our study suggests that dietary magnesium may play a role in musculoskeletal health and have relevance for population prevention strategies for sarcopenia, osteoporosis and fractures.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

p-type Ag-N dual acceptor doped ZnO thin films with long electrical stability were deposited by DC magnetron reactive co-sputtering technique. After deposition, the films were annealed at 400 °C for one hour in a nitrogen-controlled atmosphere. The deposited films were amorphous. However, after annealing they crystallize in the typical hexagonal wurtzite structure of ZnO. The Ag-N dual acceptors were incorporated substitutionally in the structure of zinc oxide and achieving that the three samples presented the p-type conductivity in the ZnO. Initial electrical properties showed a low resistivity of from 1 to10^{−3} Ω.cm, Hall mobility of tens cm2/V.s and a hole concentration from 10^{17} to 10^{19} cm^{−3}. The electrical stability analysis reveals that the p-type conductivity of the ZnO:Ag,N films is very stable and does not revert to n-type, even after 36 months of aging. These results reveal the feasibility of using these films for applications in short-wavelength or transparent optoelectronic devices.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

The influences of doped hole transporting layer (HTL) on the performances of perovskite solar cells were studied. The influences of electrostatic and surface roughness effect by solvent additive doping were compared. The electrostatic effect of solvent additive doping was compared by addition of 1,8-diiodooctane and 1,8-dichlorooctane to the HTL layer. The surface roughness effect of solvent additive doping was examined using atomic force microscopy. The perovskite crystallinity by doping HTL was studied by X-ray diffraction. The conductivity of HTL was measured using four probe methods and was higher for doped devices. Enhanced conductivity of PEDOT:PSS film was also proved using fluorescence emission quenching. Long-term stability of the device was enhanced by doping HTL. The device with solvent additive exhibited much enhanced stability, retained over 80% of the initial PCE for 400 hours, while PCE of the device without solvent additive decreased to less than 80% after 200 hours. A very weak power microwave treatment was used for post-annealing of the fully fabricated devices. Post-annealing enhanced the lifetime of the device. Comparing different size of cells, the device lifetime was decreased as the cell area increased and as the size of the cell increased, the extent of lifetime enhancement by doping was increased.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

Mulberry (Morus alba L), a significant fruit tree crop, requires magnesium (Mg) for its optimal growth and productivity. Nonetheless, our understanding of the molecular basis underlying magnesium stress tolerance in mulberry plants remains unexplored. In our previous study, we identified several differential candidate genes associated with Mg homeostasis via transcriptome analysis including xyloglucan endotransglucosylase/hydrolase (XTH) gene family. The XTH gene family is crucial for plant cell wall reconstruction and stress responses. These genes have been identified and thoroughly investigated in various plant species. However, there is no research pertaining to XTH genes within the M. alba plant. This research systematically examined the M. alba XTH (MaXTH) gene family at the genomic level using a bioinformatic approach. In total, 22 MaXTH genes were discovered and contained the Glyco_hydro_16 and XET_C conserved domains. The MaXTH’s were categorized into five distinct groups by their phylogenetic relationships. The gene structure possesses four exons and three introns. Furthermore, the MaXTH gene promoter analysis reveals a plethora of cis-regulatory elements; mainly stress responsiveness, growth and development, light responsiveness, and phytohormone responsiveness. GO analysis indicated that MaXTHs encode proteins that exhibit xyloglucan xyloglucosyl transferase and hydrolase activities in addition cell wall biogenesis as well as xyloglucan and carbohydrate metabolic processes. Moreover, a synteny analysis unveiled an evolutionary relationship between the XTH genes in M. alba and those in three other species: A. thaliana, P. trichocarpa, and Zea mays. Expression profiles from RNA-Seq data displayed distinct expression patterns of XTH genes in M. alba leaf tissue during Mg treatments. Real-time quantitative PCR analysis confirmed the expression of the MaXTH genes in Mg stress response. Overall, this research enhances our understanding of the characteristics of MaXTH gene family members and lays the foundation for future functional genomic study in M. alba.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

Materials based on Mg2+-containing phosphates are gaining great relevance in the field of bone tissue repair via regenerative medicine methods. Magnesium ions, together with condensed phosphate ions, play a significant role in the process of bone remodeling, affecting the early stage of bone regeneration through active participation in the process of osteosynthesis. Here we pro-vide a comprehensive overview of the usage of biomaterials based on magnesium phosphate and magnesium calcium phosphate in bone reconstruction. The role of magnesium ions in angiogene-sis, an important process associated with osteogenesis, is considered. Finally, the biological properties of magnesium phosphates for bone regeneration are summarized. They show promis-ing results in terms of use as bone replacement material.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

Purpose: Obstructive sleep apnoea (OSA) affects patients’ quality of life and health. Magnesium (Mg) is an essential mineral and a potent antioxidant. Mg deficiency can worsen oxidative stress caused by sleep deprivation or disorders. The impact of OSA on serum Mg levels and its health consequences remain unclear. Methods: This study systematically reviewed clinical studies investigating the serum Mg levels of OSA patients and the potential relationships with other biomarkers.Results: Six articles were included for qualitative synthesis; five were used in quantitative analysis. Two out of four studies that compared OSA patients to healthy controls found them to have significantly lower serum Mg levels. Our meta-analysis with three studies shows that patients with OSA had significantly lower serum Mg with an effect size of -1.22 (95% CI: -2.24, -0.21). However, the mean serum Mg level of OSA patients (n=251) pooled from five studies (1.90 mg/dL, 95% CI: 1.77, 2.04) does not differ significantly from the normal range. OSA severity appears to affect serum Mg negatively. Serum Mg levels generally improve after treatment, coincide with the improvement of OSA severity. Low serum Mg levels correlate with worsening of cardiovascular risk biomarkers of C-reactive protein, ischaemia-modified albumin, and carotid intima-media thickness. The serum Mg levels also potentially correlate with biomarkers for lipid profile, glucose metabolism, calcium and heavy metals. Conclusions: Sleep deprivation appears to deplete Mg levels of OSA patients, making them at risk of Mg deficiency, which potentially increases systemic inflammation and the risk of cardiovascular and metabolic diseases.

Magnesium (Mg) is a vital element, which involves in various key cellular processes in plants. Mg transporter (MGT) genes play an important role in magnesium distribution and ionic balance maintenance. Here, MGT family members were identified and characterized in three species of the plant family Malvaceae, including Theobroma cacao, Corchorus capsularis, and Gossypium hirsutum to improve our understanding of their structure, regulatory systems, functions, and possible interactions. We identified 18, 41, and 16 putative non-redundant MGT genes from the genome of T. cacao, G. hirsutum, and C. capsularis, respectively, which were clustered into five groups within maximum likelihood tree. Several segmental/tandem duplication events were determined between MGTs genes. It seems that MGTs were slowly evolving and have been evolved under a purifying selection. Analysis of gene promoter regions showed that MGTs have a high potential to respond to biotic/abiotic stresses as well as hormones. The expression patterns of MGT genes revealed their possible T. cacaorole in response to P. megakarya fungi in T. cacao, whereas MGT genes showed differential expression in various tissues and respond to several abiotic stresses, including cold, salt, drought, and heat stress in G. hirsutum. Besides, the co-expressions network of MGTs indicated that genes involved in auxin responsive, lipid metabolism, cell wall organization, and photoprotection can interact with MGTs.

Plants produce above- and below-ground biomass. However, our understanding of both production and decomposition of below-ground biomass is poor, largely because of the difficulties of accessing study materials. Below-ground organic matter decomposition studies are scanty and especially rare in the tropics. Here, we used a litter bag experiment to quantify the mass loss and nutrients dynamics of decomposing twigs and fine roots from an arbuscular mycorrhizal fungal associated tree, Parashorea chinensis, in a tropical rain forest in Southwest China. Overall, twig litter decomposed 1.9 times faster than fine roots (decay rate (k) twig=0.255, root=0.134). The difference in decomposition rates can be explained by a difference in phosphorus (P) concentration, availability and use by decomposers or C quality. Both materials showed an increase in N concentration, with final measurements still higher than initial levels. This suggests N may not be available due to microbial immobilization. Both carbon and nitrogen dynamics were significantly predicted by mass loss and showed a negative and positive relationship, respectively. Our study results imply that fine roots carbon and nitrogen contribute more to soils organic matter and enlarge the resident time. Therefore, better understanding of carbon cycle requires better understanding of mechanisms governing below ground biomass decomposition.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

Concern over potential antimony mediated toxicity from mining and smelting activities has instigated novel concepts toward removing aqueous antimony ions. The iron based adsorbent Fe3O4/HCO was found to be efficient for treating antimony-containing wastewater However, ineffective methodology for preparation limited its effective adsorption capacity and thus wider application. In this study, a new type of HCO-doped-(Fe3O4)x adsorbent was prepared by co-precipitation method for doping Fe3O4 into HCO sludge (HCO), thereby improving adsorption performance for Sb(III) and Sb(V) ions, with the maximum adsorbing capacity being 44.46 mg/g and 47.91 mg/g, respectively. According to the results of BET, SEM-EDS, XRD and XPS, it were confirmed that the FeOOH and X≡Fe-OH were formed during the preparation process, bring about the increased the surface area, thus resulting in further increase of surface area, hydroxyl groups and the net negative ionic charge. Moreover, the adsorption kinetics followed the pseudo-second-order kinetic model which indicated that adsorption process of Sb(III)/Sb(V) by HCO-doped-(Fe3O4)x adsorbent was controlled by chemical reaction. The main adsorption mechanism is that antimony ion and amorphous iron oxide X≡Fe-OH undergo coordination exchange reaction and complexation reaction with CeO2 or Ce2O3. Furthermore, HCO-doped-(Fe3O4)x could adapt to wide pH and had stable adsorption ability after regeneration. The good adsorption performance of HCO-doped-(Fe3O4)x makes it a potential applications of adsorbent for removal of antimony.

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.

The problem of effective immobilization of liquid radioactive waste (LRW) is key to the successful development of nuclear energy. The possibility of using magnesium potassium phosphate (MKP) compound for LRW immobilization on the example of nitric acid solutions containing actinides and rare earth elements (REE), including high level waste (HLW) surrogate solution is considered in the research work. Under the study of phase composition and structure of the MKP compounds obtained by the XRD and SEM methods, it was established that the compounds are composed of crystalline phases - analogues of natural phosphate minerals (struvite, metaankoleite). The hydrolytic stability of the compounds was determined according to the semi-dynamic test GOST R 52126-2003. Low leaching rates of radionuclides from the compound are established, including a differential leaching rate of ²³⁹Pu and ²⁴¹Am - 3.5 × 10^-7 and 5.3 × 10^-7 g/(cm²∙day). As a result of the research work it was concluded that the MKP compound is promising for LRW immobilization and can become an alternative material combining the advantages of easy implementation of the technology like cementation and the high physical and chemical stability corresponding to a glass-like compound.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

The intermediate filament protein vimentin constitutes a critical sensor for electrophilic and oxidative stress. We previously showed that vimentin interacts with zinc, which affects its assembly and redox sensing. Here we have used vimentin wt and C328S, an oxidation-resistant mutant showing improved NaCl-induced polymerization, to assess the impact of zinc on soluble and polymerized vimentin by light scattering and electron microscopy. Zinc acts as a switch, reversibly inducing the formation of vimentin oligomeric species. High zinc concentrations elicit optically-detectable vimentin structures with a characteristic morphology depending on the support. These effects also occur in vimentin C328S, but are not mimicked by magnesium. Treatment of vimentin with micromolar zinc induces fibril-like particles that do not assemble into filaments, but form aggregates upon subsequent addition of NaCl. In contrast, when added to NaCl-polymerized vimentin, zinc increases the diameter or induces lateral association of vimentin wt filaments. Remarkably, these effects are absent or attenuated in vimentin C328S filaments. Therefore, the zinc-vimentin interaction depends on the chemical environment and on the assembly state of the protein, leading to atypical polymerization of soluble vimentin, likely through electrostatic interactions, or to broadening and lateral association of preformed filaments through mechanisms requiring the cysteine residue. Thus, impact of zinc on vimentin assembly and redox regulation is envisaged.

Fast-scan cyclic voltammetry (FSCV) is an electrochemical sensing technique that can be used for neurochemical sensing with high spatiotemporal resolution. Carbon fiber microelectrodes (CFMEs) are traditionally used as FSCV sensors. However, CFMEs are prone to electrochemical fouling caused by oxidative byproducts of repeated serotonin (5-HT) exposure, which makes them less suitable as a chronic 5-HT sensor. Our team is developing a boron-doped diamond microelectrode (BDDME) that has previously been shown to be relatively resistant to fouling caused by protein adsorption (biofouling). We sought to determine if the BDDME exhibits resistance to electrochemical fouling, which we explored on electrodes fabricated with either femtosecond laser cutting or physical cleaving. We recorded the oxidation current response after 25 repeated injections of 5-HT in a flow-injection-cell and compared the current drop from the first to the last injection. The 5-HT responses were compared to dopamine (DA), a neurochemical that is known to produce minimal fouling oxidative byproducts and have a stable repeated response. Physical cleaving of the BDDME yielded a reduction in fouling due to 5-HT compared to the CFME and the femtosecond laser cut BDDME. However, the femtosecond laser cut BDDME exhibited a large increase in sensitivity over the cleaved BDDME. An extended stability analysis was conducted for all device types following 5-HT fouling tests. This analysis demonstrated an improvement in the long-term stability of boron doped diamond over CFMEs, as well as a diminishing sensitivity of the laser cut BDDME over time. This work reports the electrochemical fouling performance of the BDDME when it is repeatedly exposed to DA or 5-HT, which informs the development of a chronic, diamond-based electrochemical sensor for long-term neurotransmitter measurements in vivo.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

In recent years, genetic research has been developing rapidly and taking on a larger role in research and medicine. The synthesis of any particle that can be used in this research can pave the way for new developments in this field. This research aims to develop a chemical method to produce nitrogen-doped carbon quantum dots - economical and bio-sourced substances that bind to genomic DNA. Carbon quantum dots are produced by the green synthesis hydrothermal method from radish, which is abundant in nature, and economically affordable. Nitrogen is added to increase the fluorescence properties of the produced carbon quantum dots and to improve their binding to DNA. The synthesized nitrogen-doped carbon quantum dots (N-CQDs) were tested through chromosome imaging subsequently. It was shown that N-CQDs can bind to the chromosomes, and N-CQDs reflected green light better than DAPI under the FITC filter, a potential advantage of using N-CQDs over DAPI in chromosome imaging.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

Carbonate precipitation induced by microorganism has become a hot spot in the field of carbonate sedimentology, while the effect of different magnesium on biominerals has rarely been studied. Therefore, magnesium sulfate and magnesium chloride were used to investigate the significant role played on carbonate minerals. In this study, Staphylococcus epidermidis Y2 was isolated and identified by 16S rDNA homology comparison. The ammonia, pH, carbonic anhydrase, carbonate and bicarbonate ions were investigated. The mineral phase, morphology and elemental composition were analyzed by XRD and SEM-EDS. The ultrathin slices of bacteria were analyzed by HRTEM-SAED and STEM. The result showed that this bacterium could release ammonia and carbonic anhydrase to increase pH, and elevate the supersaturation via a large number of carbonate and bicarbonate ions released through carbon dioxide hydration catalyzed by carbonic anhydrase. The crystal cell density of monohydrocalcite was lower in magnesium chloride medium than that in magnesium sulfate medium. The crystal grew in a mode of spiral staircas in magnesium sulfate medium, while in a concentric circular pattern in magnesium chloride medium. There was no obvious intracellular biomineralization. This study may be helpful to further understand the biomineralization mechanism, may also provide some references for the reconstruction of paleogeological environment.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. A doping-induced and concentration-dependent phase transition in ZrO₂ under the influence of Y₂O₃ was discovered, due to which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The results show that ab initio approaches are able to describe the mechanism of doping-induced phase transitions in (ZrO₂+Y₂O₃)-like systems, based on which it can be assumed that DFT calculations can also flawlessly evaluate other physical and chemical properties of YSZ, which have not yet been studied quantum chemical research. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

In this report, we establish a straightforward method for estimating the equilibrium constant for the CK reaction over wide but physiologically and experimentally relevant ranges of pH, Mg2+ and temperature. Our empirical formula for CK Keq” is based on experimental measurements. It can be used to estimate [ADP] when [ADP] is below the resolution of experimental measurements, a typical situation because [ADP] is on the order of micromolar concentrations in living cells, and may be much lower in many in vitro experiments. Accurate prediction of [ADP] is essential for in vivo studies of cellular energetics and metabolism, and for in vitro studies of ATP-dependent enzyme function under near-physiological conditions. With [ADP], we could estimate ΔGATP. Application to actomyosin force generation in muscle provides support for the hypothesis that, when [Pi] varies but not when pH is altered, maximum Ca2+-activated isometric force depends on ΔGATP in both living and permeabilized muscle preparations. Further analysis of the pH studies introduces a novel hypothesis for the role of submicromolar ADP in force generation.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Magnesium nanoparticles of various mean diameters (53 – 239 nm) were synthesized herein via Pulsed Laser Ablation in Liquid (PLAL) from millimeter sized magnesium powders within iso-propyl alcohol. It was observed via a 3x3 full factorial DOE that the processing parameters can control the nanoparticle distribution to produce three size-distribution types (bimodal, skewed and normal). Ablation times of 2, 5, and 25 minutes where investigated. An ablation time of 2 minutes produced a bimodal distribution with the other types seen at higher periods of processing. Mg nanoparticle UV-Vis absorbance at 204 nm increased linearly with increasing ablation time, indicating an increase in nanoparticle count. The colloidal density (mg/ml) generally increased with increasing nanoparticle mean diameter as noted via increasing UV-vis absorbance. High la-ser scan speeds (within the studied range of 3000 - 3500 mm/s) tend to increase the nanoparticle count/yield. For the first time, the effect of scan speed on colloidal density, UV-vis absorbance and nanoparticle diameter from metallic powder ablation was investigated and is reported herein. The nanoparticles formed dendritic structures after being drop cast on aluminum foil as observed via FESEM analysis. Dynamic light scattering was used to measure the size of the nanoparticles. Magnesium nanoparticles have promising use in the fabrication of wearables, such as in conductive tracks or battery electrodes, owing to their low heat capacity, high melting point and bio-compatibility.

Nutrition, diabetes, and mental disorders are interconnected and significantly impact an individual's overall health and well-being. This comprehensive review aims to explore the complex interplay between nutrition, diabetes, and mental disorders, highlighting the latest research findings in this field. While the influence of nutrition on the development and management of both diabetes and mental disorders is widely recognized, there remains a gap in understanding the intricate interplay between nutrition, mental health, and diabetes. Diabetes is associated with an increased risk of mental disorders, including depression, anxiety, and cognitive decline. Mental disorders can also contribute to the development of diabetes through various mechanisms including increased stress, poor self-care behaviors, and adverse effects on glucose metabolism. Thus, the mechanisms linking nutrition, diabetes, and mental disorders are complex and multi-factorial. Inflammation, oxidative stress, gut microbiota alterations, and neuroendocrine dysregulation have emerged as potential pathways that may mediate the relationship between nutrition, diabetes, and mental disorders. Additionally, deficiencies in essential nutrients such as omega-3 fatty acids, vitamin D, B vitamins, zinc, chromium, magnesium, and selenium have been implicated in the pathogenesis of both diabetes and mental disorders. Our findings indicate that the use of personalized dietary interventions and targeted nutrient supplementation can improve metabolic and mental health outcomes in patients with type 2 diabetes.

The increasing global demand for efficient and sustainable energy storage solutions has driven the exploration of sulfur-based battery technologies. Sulfur’s abundance, low cost, and high theoretical energy density make it a promising candidate for next-generation energy storage, particularly in electric vehicles (EVs) and renewable energy systems. This paper reviews the development of sulfur-based batteries, including lithium-sulfur (Li-S), sodium-sulfur (Na-S), magnesium-sulfur (Mg-S), solid-state sulfur, sulfur-carbon nanocomposites, and hybrid sulfur flow batteries. Each technology is analyzed based on its advantages, challenges, and potential applications. Key research areas such as advanced electrolytes, nanomaterial integration, and sustainable manufacturing are highlighted, along with the current technological barriers to large-scale adoption. This review underscores the importance of continued research and innovation in sulfur-based battery technology to meet future energy storage demands.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

A typical halogen-free flame-retardant (HFFR) formulation for electric cables may contain polymers, various additives, and fire-retardant fillers. In this study, composites are prepared by mixing natural magnesium hydroxide (n-MDH) with linear low-density polyethylene (LLDPE) and a few types of ethylene-octene copolymers (C₈-POE). Depending on the content of LLDPE and C₈-POE, we obtained composites with different crystallinity that affected the final mechanical properties. The nucleation effect of the n-MDH and the variations in crystallinity caused by the blending of C₈-POE/LLDPE/n-MDH were investigated. In the C₈-POE/LLDPE blend, we found a decrease in the crystallization temperature of LLPDE compared to pure LLDPE and an increase in the crystallization temperature of C₈-POE compared to pure C₈-POE. On the contrary, the addition of n-MDH led to an increase in the crystallization temperature of LLDPE. As expected, the increase in the crystallinity of the polyolefin matrix of composites led to higher elastic modulus, higher tensile strength, and lower elongation at break. Overall, these results show how to obtain the required mechanical features for halogen-free flame-retardant compounds for electric cable applications depending on the quantities of the two miscible components in the final blend.

Traditional photodynamic therapy (PDT), a clinical cancer therapeutic approach using light in killing cancer cells, is often limited by insufficient light penetration, inefficient photosensitizer energy transfer, and inadequate oxygen in hypoxic tumors. Employing X-ray to activate photosensitizer in PDT can potentially overcome these limitations. Here, we compared protocols to synthesize a novel nano-photosensitizer composed of a europium-doped yttrium oxide core with a silica shell (Y₂O₃:Eu@SiO₂) which can be utilized in such therapeutic method, i.e., X-ray activated PDT (XPDT). Transmission electron microscopy (TEM) and dihydroethidium (DHE) were utilized to evaluate the effects of various synthesis conditions on the characteristics of Y₂O₃:Eu@SiO₂ and their ability to generate reactive oxygen species (ROS). The in vivo tumor suppression effects of the Y₂O₃:Eu@SiO₂ were assessed by ¹⁸F-fluorothymidine position emission tomography (¹⁸F-FLT PET) in human ovarian cancer xenografts using radiation sensitive CAOV3 and radiation resistant SKOV3 cell lines. Our data revealed a positive correlation between nanoparticle condensation time and core size as well as a negative correlation between urea concentrations and core size. Addition of cetyltrimethylammonium bromide (CTAB) during core synthesis enhanced particle dispersion. Two silica coating conditions showed the greatest efficiency in the enhancement of ROS generation. Furthermore, our in vivo study revealed suppression of tumor growth by Y₂O₃:Eu@SiO₂ administration when compared to non-treated control. Silica shell provides flexibility to conjugate moieties that specifically target to cancers. This nano-photosensitizer demonstrates the significant promise for overcoming limitations of conventional PDT and combating various cancers in clinical applications.

Increased screen time during the COVID-19 pandemic and the accelerated incorporation of technology into daily practices have directly contributed to the increased prevalence of eye disease. The human eye is not built for continual technological use and must adjust to exposure to digital screens. Overexposure to technology can result in eye strain and an increased risk of eye diseases such as myopia with complications later in life, including retinal tears, cataracts, and macular degeneration. As vision and ocular diseases become more prevalent, the study of eye diseases, including their causes and treatments, is especially relevant. There is a need to prevent ocular diseases before they become a burden to individuals, their families, and their communities by better understanding the pathophysiology of ocular diseases. Several ocular diseases are thought to be caused by imbalances in reactive oxygen species (ROS) and autophagy. ROS refers to a class of highly reactive oxygen-containing molecules that can undergo damaging reactions with other molecules in the cell. Autophagy is a cellular process of self-eating whereby damaged, harmful, or dead material in cells is broken down to maintain cellular homeostasis. This paper discusses the role of ROS and autophagy in the pathogenesis of computer vision syndrome (CVS), digital eye strain (DES), myopia, cataracts, glaucoma, diabetic retinopathy (DR), age-related macular degeneration (AMD), optic nerve crush injury (OCN), optic nerve gliomas, and retinoblastoma. Lifestyle changes such as limiting screen time, ensuring adequate exposure to evening sunlight, and using blue light protection measures or protective eyewear are important in the prevention of eye disease. Nutrition also contributes significantly to eye health. A balanced diet rich in vitamins and antioxidants may help to prevent ROS and autophagy imbalance-induced eye disease. Medical and surgical treatments become necessary when preventative measures fail. This paper also addresses how government measures to decrease the onset of eye disease, including targeted programs to increase access to fresh vegetables and fruits in food deserts, are a critical macro-level avenue to reduce eye disease prevalence in the US, which according to the National Eye Institute, costs $139 billion yearly.