The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

Biochar application to the soil can improve soil quality and nutrient leaching loss. Recent studies have reported that surficial application of biochar to stored swine manure can reduce emissions of odorous compounds and reduce the volatilization loss of ammonia. Our working hypothesis was that the biochar-treated manure application to the soil would decrease nutrient leaching from manure and increase plant-available nutrients. The study objectives were to evaluate the impact of biochar-treated swine manure on soil total C, N, and other major and minor nutrients. Three biochars (i) neutral pH red-oak (RO), (ii) highly alkaline autothermal corn (Zea mays) stover (HAP), and (iii) mild acidic Fe-treated autothermal corn stover (HAPE) were incubated with swine manure for a month. The biochar-manure mixture was applied in triplicate to soil columns with application rate determined by the P₂O₅-P content in manure or manure-biochar mixtures after the incubation. The ammonium (NH₄⁺), nitrate (NO₃^-), and reactive P concentrations in soil column leachates were recorded for eight leaching events. Soil properties and plant-available nutrients were compared between treatments and control manure & soil. Manure-(HAP&HAPE) biochar treatments significantly increased soil organic matter (OM) and increased soil total C, N, and improved soil bulk density. Concentrations of KCl-extractable NH₄⁺ and NO₃^- significantly increased in HAPE column leachates during this 4-week study and in the soil after the experiment. A significant reduction in soil Mehlich3 Cu was also observed for the manure-HAPE mixture compared with the control. Overall, the manure-biochar incubation enabled biochar to sorb nutrients from manure, and the subsequent manure-biochar mixture application to soil improved soil quality and plant nutrient availability in comparison to conventional manure application to soil. This proof-of-the-concept study suggests that biochars could be used to solve both environmental and agronomic challenges and further improve the sustainability of animal and crop production agriculture.

HDPE (high-density polyethene) plastic waste is stronger, harder, and more resistant to high temperatures than other plastics. Using it as an additive in a concrete mixture is one solution to reduce this type of waste. We examined how HDPE-type plastics can be used as an additive material in the manufacture of concrete to improve its hardness, tensile strength and compressive strength. Using 156 samples, we aimed to identify the effect of HDPE plastic fibres on concrete of three qualities; B0, f'c10 MPa (low quality), and f'c25 MPa (medium and high quality). We added four compositions (2.5%, 5%, 10% and 20% by weight of cement) of HDPE plastic fibre to each quality of cement, with HDPE plastic fibre sizes of 1 x 1 cm, 0.5 x 2 cm or 0.25 x 4 cm. We found that the addition of 5% HDPE plastic fibre with a 0.5 x 2 cm cross-sectional shape to the f'c10 MPa concrete gives the best result, with increased tensile and compressive strength of the concrete.

The food distribution process is responsible for significant quality loss in perishable products. However, preserving quality is costly and consumes a tremendous amount of energy. To tackle the challenge of minimizing transportation costs and CO2 emissions while also maximizing product freshness, a novel multi-objective model is proposed. The model integrates a vehicle routing problem with temperature, shelf life, and energy consumption prediction models, thereby enhancing its accuracy. Non-dominated sorting genetic algorithm II is adapted to solve the proposed model for the set of Solomon test data. The conflicting nature of these objectives and the sensitivity of the model to shelf life and shipping container temperature settings are analyzed. The results show that optimizing freshness objective degrade the cost and the emission objectives, and the distribution of perishable foods are sensible to the shelf life of the perishable foods and temperature settings inside the container.

Construction and demolition waste (CDW) represents 1/3 of the weight of all-waste produced. Increasing their recycling and reutilization with recycled aggregates (RA) means closing the life cycle of construction materials. Research has been carried out on artificial aggregates from the exclusive crushing of structural concrete waste in selective demolitions (CDWRConc). This study analyses the use of recycled concrete as graded aggregate (GARConc) and in cement soil (CSRConc). The material complies with the requirements as a road base, although due to the low values of resistance to fragmentation these materials are adequate for use in sensitive road systems and other places such as urban roads and car parks. The sensitive road systems are infrastructures in places of great natural wealth and low traffic intensity, with an annual average of heavy vehicle traffic (AADTh) below 50 vhp/d. As soluble salt contents have been detected, additional waterproofing or drainage measures must be adopted to prevent water infiltration into the layers made up of CDWRHorm. Finally, the high initial values of UCS allow the temporary passage of light vehicles over CSRConc after 3 days.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Global food waste has a huge impact on the environment, as it is a source of greenhouse gas (GHG) emissions and wasted natural resources. Across the world, over 30% of food is lost or wasted each year. Aside from this, food industry, as well, is one of the biggest sources of agro-industrial waste and by-products, which can be valorized and used for different purposes. Such waste is a good source of bioactive organic compounds which can be extracted without al-tering their properties, where deep eutectic solvents (DESs) can serve as green solvents and excel-lent replacement for volatile organic solvents. Isolated compounds can be used in innovative food production, chemical production, cosmetics and other industries. DESs have attracted extraordi-nary attention due to their advantages such as environmental friendliness, availability and easy preparation, easy handling and utilization of non-toxic components for their formation. Due to those properties, they are a greener alternative to classic organic solvents for many processes, in-cluding extractions. In this paper, we review the utilization of deep eutectic solvents as potential green media for the extraction of organic compounds such as polyphenols, carbohydrates, pro-teins, alkaloids from by-products of the food industry and agro-industrial-waste.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Red mud (RM) is composed of a waste alkaline solution (pH = 13.3) obtained from the production of alumina. It contains high concentrations of soluble hematite (Fe2O3), goetite (FeOOH), gibisite [Al(OH)3], a boemite (AlOOH), anatase (Tetragonal - TiO2), rutile (Ditetragonal dipyramidal - TiO2), hydrogarnets [Ca3Al2(SiO4)3−x(OH)4x], and perovskite (CaTiO3). It was shown to be an excellent catalytic mixture for biodiesel production. To demonstrate the value of RM, an environmentally friendly process of transesterification in aqueous medium using waste cooking oil (WCO), MeOH and waste alkaline solution (WAS) obtained from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 oC to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 0.019% (w/w) WAS/WCO using the WAS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process. The use of the new catalyst (WAS) resulted in a high yield of the products (greater than 99% yield).

As a result of rapid population growth, an exponentially growing human population, and industrial expansion, it has become increasingly difficult to manage municipal solid wastes throughout the world. Decentralized waste management systems have created difficult situations in developing countries such as Malaysia. Wastes generated in the country, due to various cultural, social, and religious activities, organic and contributing to environmental pollution (air, water, and soil) and human health troubles. A questionnaire survey was participated by 220 construction professionals in Malaysia using structured and semi-structured methods. The framework was assessed using A partial least square structural equation modeling (PLS-SEM) to target sustainable development goals (SDG). Statistical analysis results indicate a significant effect between SCW management, since(r(270)=.687, P&lt;0.001). Improving factors has strong relationship with SCW management, since(r(270)=.723, P&lt;0.001). The mediation results also suggested a significant indirect positive effect of improving factors drivers on SCW management through policy-related factors sinceβ=0.688, t=8.254, P&lt;0.001, 95% CI for β=0.536,0.866. Finally, policy-related factors construct has a strong relationship with SCWM) management, since(r(270)=.811, P&lt;0.001) With the R Square of 0.787 and 0.785. The developed framework can improve construction waste management in the construction industry and enhance construction waste management to achieve global sustainable development goals. The findings show that one of the most critical issues of enhancing profitability is using preventive policies to reduce construction waste. This study could guide construction industry stakeholders in identifying the different waste management features during a building project's construction and design stage

The extraction of grape processing waste (wine pomace) via microwave-hydrodiffusion and gravity (MHG) from three different cultivars grown in Sicily (Syrah, Perricone and Nero d’Avola) rapidly affords aqueous extracts highly concentrated in valued biophenols including flavonoids, anthocyanins and phenolic acids. The method does not employ organic solvent, acid or base and does not require grinding or freeze drying of the wine pomace nor separation of the grape skins from seeds and stem. All the extracts have a pronounced stability as shown by their red-violet color fully retained after storage for more than a year (15 months) in freezer under air. Concentrations of phenolics up to 2000 ppm were detected in the aged extracts of Sicily’s local cultivar Perricone, which also has the highest content of flavonoids. These findings provide a simple and economically viable extraction route to biophenol-rich red extracts that can be used as food colorants as well as to formulate nutraceutical, cosmetic and personal care products starting from an agricultural by-product available in >10 million tonne yearly amount.

As a consequence of intense industrialization in the last few decades, the amount of agro-industrial wastes has increasing, where new forms of valorization are crucial. In this work, 5 residual biomasses from Maranhão (Brazil) were investigted as supports for immobilization of lipase from Thermomyces lanuginosus (TLL). The new biocatalysts BM-TLL (babaçu mesocarp) and RH-TLL (rice husk) showed immobilization efficiencies &gt;98% and hydrolytic activities of 5,331 U.g-1 and 4.608 U. g-1 respectively against 142 U. g-1 by Lipozyme® TL IM. High esterification activities were also found, with 141.4 U.g-1 and 396.4 U.g-1 from BM-TLL and RH-TLL against 113.5 U.g-1 by TL IM. Results of porosimetry, SEM and BET demonstrated BM and RH supports are mesoporous materials with large hydrophobic area, allowing a mixture of hydrophobic adsorption and confinement, resulting in hyperactivation of TLL. These biocatalysts were applied in the production of hexyl laurate, where RH-TLL was able to generate 94% conversion in 4 h. Desorption with Triton X-100 and NaCl confirmed that new biocatalysts were more efficient with 5 times less protein than commercial TL IM. All results demonstrated that residual biomass was able to produce robust and stable biocatalysts containing immobilized TLL with better results than commercial preparations.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

Hydrogen sulfide and ammonia are always a concern in the livestock industries, especially when farmers try to clear their manure storage pits. Agitation of manure can cause dangerously high concentrations of harmful agents such as H₂S and NH₃ to be emitted into the air. Biochar has the ability to sorb these gases. We hypothesized that applying biochar on top of manure can create an effective barrier to protect farmers and animals from exposure to NH₃ and H₂S. In this study, two kinds of biochar were tested, highly alkaline, and porous (HAP, pH 9.2) biochar made from corn stover and red oak biochar (RO, pH 7.5). Two scenarios of (6 mm) 0.25” and (12 mm) 0.5” thick layers of biochar treatments were topically applied to the manure and tested on a pilot-scale setup, simulating a deep pit storage. Each setup experienced 3-min of agitation using a transfer pump, and measurements of the concentrations of NH₃ and H₂S were taken in real-time and measured until the concentration stabilized after the sharp increase in concentration due to agitation. The results were compared with the control in the following 3 situations: 1. The maximum (peak) flux 2. Total emission from the start of agitation until the concentration stabilized, and 3. The total emission during the 3 min of agitation. For NH₃, 0.5” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 63.3%, overall total emission by 70%, and total emissions during the 3-min agitation by 85.2%; 0.25” HAP biochar treatment significantly (p<0.05) reduced maximum flux by 75.7%, overall, total emission by 74.5%, and total emissions during the 3-min agitation by 77.8%. 0.5” RO biochar treatment significantly reduced max by 8.8%, overall total emission by 52.9%, and total emission during 3-min agitation by 56.8%; 0.25” RO biochar treatment significantly reduced max by 61.3%, overall total emission by 86.1%, and total emission during 3-min agitation by 62.7%. For H₂S, 0.5” HAP biochar treatment reduced the max by 42.5% (p=0.125), overall total emission by 17.9% (p=0.290), and significantly reduced the total emission during 3-min agitation by 70.4%; 0.25” HAP treatment reduced max by 60.6% (p=0.058), and significantly reduced overall and 3-min agitation’s total emission by 64.4% and 66.6%, respectively. 0.5” RO biochar treatment reduce the max flux by 23.6% (p=0.145), and significantly reduced overall and 3-min total emission by 39.3% and 62.4%, respectively; 0.25” RO treatment significantly reduced the max flux by 63%, overall total emission by 84.7%, and total emission during 3-min agitation by 67.4%.

The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

Waste biogenic materials from seafood exploitation are valuable resources of new compounds exploitation within the blue bioeconomy concept. Here, we describe the effectiveness of Raman technology implementation as an in-line tool for demineralization process control of crustaceans or gastropods. We produced transparent chitin polymer foils from three waste crustacean shells (C. sapidus, S. mantis and M. squinado) using a slow, green chemical approach employing acetic acid, and showed the progressive process of biogenic carbonate dissolution and increasing the Raman characteristic signal of chitin, in a time dependence manner. It turned that chitin foils obtaining is species-specific, and the demineralization bath of waste shell mixture can be effectively tracked by Raman spectroscopy, for solvent control and the recovery of the calcium acetate as valuable by-product. Comparatively, calcium acetate drug, a compound widely used in kidney failure diseases, or as additive in nutraceuticals and food industry, has been obtained here, following a green demineralization path of the sea snail Rapana venosa intact shell, assisted by Raman tech-nology, using 9% acetic acid (vinegar) solution for 14 days. To validate the final products identity and quality, The process of waste shells demineralization and the final products of the treatment were investigated using various Raman techniques and technologies, cross-validating the results with FT-IR, XRD and SEM-EDX techniques. NIR Raman spectroscopy revealed chitin bands in a time-dependent manner, while Resonance Raman spectroscopy showed the preservation of ca-rotenoids after two weeks of acetic acid treatment. A hand-held flexible TacticID Raman system with a 1064 nm excitation demonstrated its effectiveness as a rapid, in-line decision making tool during process control and revealed excellent reproducibility of the lab-based instrument signal, suitable for in situ evaluation of the demineralization status and solvent saturation control. The calcium acetate recovered from residual treatment solutions was assessed regarding its hydration status, purity, and suitability as recrystallized material for further use as pharmaceutical product or ingredient in complex formulations.

Abstract Global marine fish harvest has reached a plateau over the last decade. Efforts to increase aquaculture tend to face limitations in water resources and contamination problems. Of the current fish harvest at least 50% is discarded as waste. The chemical and microbiological contaminations limit the utilization of harvested fish. There is a need to improve fish preservation to minimize spoilage and process them into more appealing products. Instead of resorting to individual food processing methods, the efficiency of processing could best be increased by a combination of conventional and modern processing methods, or combinations of modern processing methods. Fish waste is a rich source of oils containing essential fatty acids, polypeptides, and amino polysaccharides that could be utilized through upscaling of the current scientifically proven methods, to new processing technologies. Separation of collagens, gelatins, bioactive peptides, edible fish oils, and chitosan form the primary stages in the utilization of fish waste. The products need purification to meet food quality and safety standards, and desirable industrial characteristics. The diversity of information and products generated through new methods requires advanced data handling and prediction systems, such as artificial intelligence, to address food safety and get the best out of fish processing and utilization.

The regional recycling of plant waste from municipal green space maintenance, private households and private gardens is traditionally carried out in partially open composting plants. In addition to climate-relevant gases, dust, germs and odours are emitted. Compared to aerobic rotting the pyrolysis at higher temperatures and/or reforming offers industrial utilisation of plant based biowaste, with additional availability of energetic by-products. A high-quality plant charcoal derived from a pilot plant is used in a one-year field trial to establish a theoretical comparability with substrates from composting. The advantages and disadvantages of composting and high-quality pyrolysis is shown for comparison, to foster further investigation in advanced technologies for production of plant charcoal aiming the sequester of biogenic Carbondioxide.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Pyrochlore oxides (A2B2O7) are potential nuclear waste substrate material due to their superior radiation resistance properties. We performed molecular dynamics simulations to study the structural properties and displacement cascades in ytterbium titanate pyrochlore (Yb2Ti2O7). We computed threshold displacement energy ( Ed ) and lattice constant ( ao) of Yb2Ti2O7. The effect of displacement cascades in Yb2Ti2O7 of recoils of energies 1 keV, 2 keV, 5 keV, 10 keV in different crystallographic directions ([100], [110], [111]) were studied. The number of defects is found to be proportional to the energy of incident PKA. Additionally, the Ed of pyrochlore is computed and it exhibits anisotropy. Furthermore, radiation damage in high-entropy pyrochlore (HEPy) i.e., YbYTiZrO7, YbGdTiZrO7 , Yb0.5Y0.5Eu0.5Gd0.5TiZrO7 were investigated and compared with Yb2Ti2O7. It was found that HEPy have a larger Ed as compared with Yb2Ti2O7 which exhibits characteristic of lower radiation damage resistance than HEPy. Our simulation proposed that HEPy alloys are more radiation resistant than individual pyrochlore constituents . This work will provide atomic insights in developing substrate materials for nuclear waste applications.

Encapsulation is a valuable strategy to protect and deliver anthocyanins (ACNs), phenolic com-pounds with outstanding antioxidant capacity but limited stability. In this study, coacervation was used to encapsulate an ACNs-rich red cabbage extract (RCE). Two agri-food by-products polymers, whey protein isolate (WPI) and apple high-methoxyl pectin (HMP), were blended at pH 4.0 in a specific ratio to induce the formation of nanoparticles (NPs). The process optimisation yielded a monodispersed population (PDI < 0.200) of negatively charged (-17 mV) NPs with an average diameter of 380 nm. RCE concentration influenced size, charge, and antioxidant capacity in a dose-dependent manner. NPs were also sensitive to pH increase from 4 to 7, showing a progressive breakdown. The encapsulation efficiency was 30%, with a retention of ACNs within the polymeric matrix being influenced by their chemical structure: diacylated and/or C3-triglucoside forms were more efficiently encapsulated than monoacylated C3-diglucosides. In conclusion, we report a promising, simple, and sustainable method to produce monodispersed NPs for ACNs encapsu-lation and delivery. Evidence of differential binding of ACNs to NPs, dependent on specific ac-ylation/glycosylation patterns, indicate that care must be taken in the choice of the appropriate NPs formulation for the encapsulation of phenolic compounds.

The use of the commercial simulator Aspen Plus® could bring an amelioration in the accuracy of the predictions of the chemical species composition in the output streams of the anaerobic digestion process, due to availability of a broad library of thermodynamic and phenomena transport properties in this commercial package. In the present investigation, the process simulation model for anaerobic digestion, which was originally developed by Rajendran et al. [1], has been modified by including a stoichiometric-equilibria reactor to calculate the extent of the ionization of the molecules present in the anaerobic digestate. The refined model offers a more accurate prediction of the composition of the biogas because it delves on the chemical equilibrium of the gaseous stream and the anaerobic digestate. Additionally, the refined model allows to assess the possibility of upgrading the gaseous stream to biomethane degree via manufacturing of ammonium bicarbonate. This processing pathway relies on the stabilization of the anaerobic digestate by means of biomass ash-based treatment. First of all, the titration of the manure digestate with the hydrochloric acid showed that a dose of 3.18 mEq/g would be required to attain the targeted pH of zero-point charge, upon addition of the sewage sludge ash in a ratio to the manure digestate of 0.6 ± 0.2 %. Secondly, the profiles of ammonia, carbon dioxide, and methane found in the biogas agree with both the pH of the treated digestate and the processes described in for the simultaneously upgrading the biogas and the production of ammonium bicarbonate. The refined Aspen Plus® model presented in this article needs to be further developed to ensure the standards are attained in all output streams of stabilized anaerobic digestate, biomethane, and isolated added-value chemical fertilizers.

Ever-increasing need for improving the livability of a city and improve outcomes for its residents, over the last decade, the adoption of technology to develop urbanised societies around the world has given rise to the need for developing smart cities. The speed at which the world population is growing, the use of Internet of Things in smart cities have really advanced the quality of life. One significant area of concern within the smart city framework is waste management. If the waste within a city is not adequately managed, then it leads to issues in the health of the citizens. Additionally, the waste management has such a high impact on the environmental footprint, hence the need to have a smart way of managing waste is of critical importance. Through our research, we analyse the challenges of waste management within a city to understand the impact of the problem on to the citizens and overall city operations. We then investigate ways in which we can solve these problems using the emerging technologies, such as the Internet of Things, to collect valuable data of large volumes arriving at an astronomical rate, then apply multi-agent deep reinforcement learning algorithms to harness the power of big data to extract meaningful information and actionable insights. We ingest data generated by our Internet of Things into our algorithm for three main purposes including providing the notifications to an external system, for example, a map navigation engine out of the scope for this project but a future extension for route optimisation and waste vehicle tracking; extracting and reporting the actionable insights from the underlying data; and consuming the extracted data for predictive forecasting to draw out the unknown patterns of waste fill levels within various geographical locations and again send out triggers and notification to external systems for example a waste collection authority who can efficiently schedule the waste collection vehicles and optimise the route. To achieve the above mentioned outcomes, we propose a framework that is agnostic of the hardware that it connects to and can effectively interface with a wide variety of hardware keeping a level of abstraction in the architecture.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

Alternative fuels available at low cost, friendly to natural environments and meet the energy needs and demands, have witnessed a growing demand and use today. Ethanol is an attractive renewable energy source with a high content of oxygen. Ethanol can be produced through ethanolisis, however for this work direct blending of conventional diesel, waste plastic pyrolysis oil and ethanol with commercial fuel improver CI-0808 purchased from Innospec company was attempted. The primary purpose of adding a cetane improver was to improve the combustion characteristics of the blends by at least 1- 3 ignition quality points. Five mixing ratios were chosen in the following order, 50:25:25, 60: 20:20, 70: 15:15, 80: 10:10 and 90: 5:5 for Waste Plastic Pyrolysis Oil (WPPO), ethanol and conventional diesel (CD) respectively. However, for the fuel additive mixing ratio the total volume percentage was considered and the ratio put at 0.01% of the total quantity of blended fuel. In this work WPPO, diesel blends and fuel additives improvers were used as alternative fuel. This was to evaluate their performance and emission characteristics in a stationary single cylinder water cooled experimental diesel engine. The CI-0808 was added due to its potential power to reduce emissions of CO, UHC, NO_X, PM and improved engine performance. The results obtained were compared carefully to ASTM standards and discussed using graph curves figures and tabulated values. The conclusion was that ethanol and WPPO blends can be used in diesel engines as alternative fuel without modification. Used in combination with cetane improvers the emissions reduce significantly and performance improved equalling that of conventional diesel fuel.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

The macro-litter (plastic) sea bottom pollution of 14 city harbors and marinas in North Africa and in the western Baltic Sea was investigated using a new simple mobile underwater camera system. The study was complemented by a harbor manager survey and 3D-hydrodynamic transport simulations. The average pollution in German marinas was 0.1 particles/m² sea floor (0.04–1.75). The pollution in North African marinas on average was 7 times higher (0.7 particles/m²) and exceeded 3 particles/m² in city center harbors. The resulting &gt;100,000 litter particles per harbor indicate the existence of a problem. With 73%-74%, plastic particles are dominating. Existing legal and management frameworks explain the lack of plastic bottles and bags on sea floors in Germany and are one reason for the lower pollution levels. Items that indicate the role of untreated sewage water were not found. Harbor festivals seem not to be quantitatively relevant for open sea bottom pollution. Our method tends to underestimate the pollution level. Model simulations indicate that storms can cause litter reallocations and sediment cleanings. However, marina sea floor monitoring is recommendable, because it addresses pollution hot-spots, is cost-effective and takes place close to emission sources. Further, the effectiveness of land-based pollution reduction measures can easily be assessed.

Pomegranate (Punica granatum L.) is well known for its high content in bioactives including polyphenols, flavonoids and tannins, which have been shown to exhibit a wide range of biological activity such as antioxidant, antimicrobial and anticancer effects. It is worth noting that the majority of these molecules are found in the peels (PP), which are usually disposed of after processing, causing a significant amount of waste, amounting to more than 3.6 million t/y. This work investigates MW-assisted extraction (MAE) in water for the recovery of antioxidants from PP, including the optimization of temperature and extraction times. The total phenolics, anthocyanin, flavonoid and tannin contents of the recovered extracts have been determined, as have their antioxidant activities, which were found to be 356.35 mgGAE/gextr., 303.97 µgCy3G/gextr., 37.28 mgQE/gextr., 56.48 mgGAE/gextr. and 1.43 µmolTE/gextr., respectively (according to the adopted reference). All results have been compared with those obtained using a conventional protocol. In addition, the potential for water recycling by means of nanofiltration downstream in optimized MAE has been investigated, leading to overall water reuse of approx. 75%. Energy consumption (20.92W/mgGAE) and the common green metrics, RME, E-Factor and PMI (PME), have been considered in evaluating the proposed PP valorization strategy. Finally, the biological activity of the main products has been assessed. The antimicrobial properties of the PP extracts against three Gram-positive and three Gram-negative bacteria, and their antiproliferative activity towards human cancer cells have been tested. The S. aureus bacteria was the most susceptible to the PP extracts. All tested products displayed antiproliferative activity in HeLa cells when higher concentrations were tested, with D-PP/NF being the most effective. This result was also confirmed in a clonogenic analysis, which generally indicated the possible anti-cancer activity of pomegranate peel extracts obtained using this green approach.

Coffee production generates significant amounts of by-products, posing challenges for waste management in the industry. Recent research has revealed that coffee by-products are rich in bioactive compounds suitable to produce functional food ingredients and nutraceuticals. In this review, we explore biorefinery strategies for extracting and utilizing bioactive compounds from coffee by-products, including the production of bio-based chemicals and materials, as well as the extraction of phenolic compounds, antioxidants, and dietary fiber for food applications. We propose a stepwise approach for the development of functional food ingredients and nutraceuticals from coffee by-products, covering the identification of needs, comprehensive characterization, in vitro and in vivo research, unraveling the mechanism of action, food and nutraceutical formulation, sensory analysis, shelf-life stability, scale-up, randomized control trials, and biostatistic and bioinformatic integration. Additionally, we discuss the market potential, regulatory issues, and technological innovation surrounding the commercialization of coffee by-product-based products. Emphasizing the importance of regulatory compliance and sustainability in the coffee industry, this review highlights the potential of coffee by-products to be transformed from waste into valuable functional food ingredients and nutraceuticals, offering a promising avenue for waste reduction and promoting sustainability in the coffee industry.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

The current study assessed the influence of Anti Stripping Agents (ASA), Ground Tire Rubber (GTR) and waste polyethylene terephthalate (PET) on performance behavior of binder and Stone Matrix Asphalt (SMA) mixtures. Through this paper, the 85/100 penetration grade bitumen was utilized as original bitumen. Also, three liquid ASA’s (ASA (A), ASA (B), ASA (C)) were used as a mixture modifier. For this purpose, softening point, penetration, rotational viscosity, Dynamic Shear Rheometer, Multi Stress Creep Recovery (MSCR) and Linear Amplitude Sweep (LAS) tests were implemented to investigate the rheological properties of modified bitumen. For evaluating the behavior of modified mixtures several tests such as; Resilient Modulus, Tensile Strength, dynamic creep, wheel track and four-point beam fatigue tests were implemented. Based on MSCR test results, utilization of mentioned polymers enhanced the elasticity of bitumens and therefore the permanent deformation resistance of binders increases. Also by the addition of PET percentage, the rutting resistance improves. Results indicated that utilization of ASAs, PET and Crumb Rubber (CR) enhance the Resilient Modulus (Mr), Indirect Tensile Strength (ITS), rutting resistance, fatigue life and Fracture Energy (FE) of asphalt mixtures. Also based on results, modification of binder by PET/CR with a ratio of 50%/50% and ASA (B) have the highest fatigue life which indicates that this mixture has highest resistance against fatigue cracking.

Abstract: Measures to counteract AMD generation need to start at the mineral surface, inhibiting mineral-oxidizing, acidophilic microbes. Laboratory and long-term field tests with pyrite-containing mining wastes, where Carbonaceous Phosphate Mining Waste (CPMW) was added, resulted in low acidity, and near neutral drainage. The effect was reproducible, nd confirmed by several independent research groups. This was shown to involve an organic coating, likely a biofilm. The biofilm formation was confirmed when CPMW was added to lignite coal waste with an initial pH of 1. Forty five days after the addition, the coal waste was dominated by heterotrophic microorganisms in biofilms. A review of the scientific literature supports that CPMW has physical and chemical characteristics which are capable of inducing a strong inhibitory effect on sulphide oxidation by forming an organic coating over the mineral surface. CPMW characteristics appear to provide the cornerstone of a new technology for the reduction of sulphide oxidation in mine wastes. An hypothesis for testing this technology is presented which could result in an economical and sustainable approach to mine waste and water management.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

The concept of biorefinery constitutes a significant contributing factor to the emerging transition towards a sustainable bioeconomy. In such a context, replacing oil and petrochemicals by biomass may involve several feedstocks, platforms, processes, technologies, as well as final products. This paper concentrates in the complex process of transferring the concept of biorefinery from laboratory to industry, and sheds light on the techno-economic, and complexity management dimensions involved in this endeavor. Towards this end, adopting a systems perspective, the paper presents a structured and comprehensive framework, comprising of the definition of the transformation process, business model development, technoeconomic assessment and strategic positioning and viability assessment, which may be employed to facilitate the engineering at-large and launch of a biorefining venture in a circular bioeconomy context. The framework is applied in the context of a biorefinery plant in a specific region in Southern Greece, which is based on the valorisation of olive mill wastewater (a ‘strong’ and quite common industrial waste in Mediterranean Basin), and produces biopolymers (PHAs) and bioenergy (H2).

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: The promotion of sustainable packaging is part of the European Green Deal and plays a key role in the EU’s social and political strategy. One option is the use of renewable resources and biomass waste as raw materials for polymer production. Lignocellulose biomass from annual and perennial industrial crops and agricultural residues are a major source of polysaccharides, proteins, and lignin, and can also be used to obtain plant-based extracts and essential oils. Therefore, these biomasses are considered as potential substitute for fossil-based resources. Here, the status quo of bio-based polymers is discussed and evaluated in terms of properties related to packaging applications such as gas and water vapor permeability as well as mechanical properties. So far, their practical use is still restricted due to lower performance in fundamental packaging functions that directly influence food quality and safety, the length of shelf life and thus the amount of food waste. Besides bio-based polymers, this review focuses on plant extracts as active packaging agents. Incorporating extracts of herbs, flowers, trees, and their fruits is inevitable to achieve desired material properties that are capable to prolong the food shelf life. Finally, the adoption potential of packaging based on polymers from renewable resources is discussed from a bioeconomy perspective.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

This study examines the attitudes and practices of dentists and dental students towards envi-ronmental issues within their professional context. Data was selected based on their responses on a Google Forms e-questionnaire, designed specifically for the study. The sample consisted of 78 professional dentists and 75 dental students in Greece and their attitudes towards environmental protection, awareness of the environmental impact of dental practices, and factors influencing the adoption of environmentally friendly practices were assessed. Results reveal generally positive attitudes towards environmental protection, with students demonstrating higher levels of proper waste management practices. Dentists express awareness of their environmental impact but ex-hibit varying levels of engagement in eco-friendly practices. Factors such as moral consciousness and believing in the severity of climate change significantly influence environmental awareness in dental practice. Notably, dental students exhibit greater environmental awareness compared to practicing dentists. These findings emphasize the importance of integrating environmental edu-cation into dental curricula and continuing education programs to foster sustainable practices in dental care. Future research could explore interventions to enhance environmental consciousness among practicing dentists and assess the long-term impact of environmental education initiatives on dental care sustainability.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

White-rot fungi (WRF) have specific enzymes to degrade lignocellulosic and phenolic compounds. Therefore, their direct application could be an alternative to biodegrade complex lignocellulosic biomass such as olive mill solid waste (OMSW). The aim of this study was to evaluate the capacity of A. discolor and S. hirsutum to grow in OMSW as the sole substrate under static conditions and evaluate the phenolic removal compounds and lignin degradation. The lignolytic enzyme activity was determined, as was the phenolic compound removal. At the same time, lignin degradation and structural changes were evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscope (SEM), respectively. Both strains were able to grow using OMSW as the sole substrate without adding other nutrients, oxygen and/or agitation. The higher ligninolytic enzyme activity was found at day 8, and the highest phenolic removal (more than 80% with both strains) was reached after 24 days of incubation. The CLSM analysis confirmed lignin degradation through the drop in lignin fluorescence from 3967 for untreated OMSW to 235 and 221 RFU after 24 days of treatment by A. discolor and S. hirsutum respectively. The results indicate that both WRF could be suitable candidates to design an in-situ pretreatment step of OMSW, as long as in future research the WRFs have the same performance in non-sterile conditions.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

Marine litter, comprising persistent and human-made solid materials discarded in marine environments, poses a severe threat to Nigeria's coastal and marine ecosystems. Despite existing international, regional, and national regulations, ineffective enforcement and compliance have led to widespread environmental degradation (UNEP, 2021). This study examines the factors contributing to the proliferation of marine litter in Nigeria, focusing on regulatory gaps, insufficient waste management infrastructure, and the lack of public awareness. The findings reveal that the marine ecosystem is deteriorating due to inadequate waste disposal practices and limited understanding of the impacts of marine litter on both the environment and human health (UNEP, 2021). The paper concludes with recommendations for improving regulatory enforcement, enhancing public education, and investing in waste management infrastructure to address the growing crisis of marine litter. Throughout this article, the limited information on the impacts of marine pollution across Africa is highlighted, emphasizing the value of these insights despite their scarcity.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Traditionally there is a gap between reactor operation and the consideration of nuclear waste in the final disposal. Fuel is produced and fuel must be disposed of in the view of the reactor operator, fuel has to be cleaned in the reprocessing and new solid fuel has to be produced in the view of the chemist. iMAGINE is designed to overcome this separation through the breakthrough development applying an optimized, integrative approach from cradle to grave of nuclear energy production as a first step to come as close as possible to the vision of zero waste nuclear power. It is described here the first time all in three the steps: reactor, fuel cycle, waste, providing the ratio behind each of the choices taken to come to the overall solution to open the discussion and thinking process on what could be achieved by a really innovative approach to integrated nuclear energy production. The opportunities regarding the handling of the remaining waste will be discussed with a view on the expectation of the final disposal community, the study ‘Nuclear waste from small modular reactors’, and the IAEA report ‘waste from innovative types of reactors and fuel cycles - a preliminary study. The aim of the is not to find answers to each of the raised points, but to identify first potential approaches and potentially promising ways to go, as well as to stimulate a discussion among experts. In the best case this could lead to a change of track for nuclear to become an even more sustainable and at least as important, trusted technology to help solve the net-zero challenge.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

This article attempts to identify factors impacting on the quantity of municipal waste in Polish 2478 communes (LAU-2), taking into account the variability of particular determinants influence depending on their regional diversification. The analysis covers the years 2005-2018. The dependent variable is the volume of municipal waste in kg per capita, whereas the group of determinants include: economic and human development, uncontrolled dumping sites, population density, population at the working age, migration, tourism, urbanization, dwellings and housing, retail sales, entities, education and investments in waste management; The geographically weighted regression with spatial error term (GWR-SEM) was employed in this study. The model enabled not only the specification of the waste production determinants, but also the analysis of the variability in the strength and direction of dependencies occurring between the examined variables in individual communes. The results proved that the higher the level of education the less waste is generated (in the north-central Poland); the business entities and working-age population are crucial for the waste quantity in communes of eastern Poland; the factors most considerably as to regional range affecting the waste quantity are urban and business development; as to strength–higher education and the share of working age individuals;

In this study, the effects of food waste (FW) compost, vermicompost, and chemical fertilizers on the growth of organic red radish and soil quality are investigated to promote sustainable agriculture. Utilizing a comparative approach, it assesses the impacts of these fertilizers on various plant growth metrics and soil characteristics, highlighting the potential of converting FW into nutrient-rich amendments as a sustainable alternative to chemical fertilizers. The results indicate a significant variation in fresh weight among different treatments. For example, the FV 25% treatment demonstrated a relatively high mean fresh weight of 7.9664, while the CO 50% treatment yielded a much lower mean fresh weight of 0.2589. These numbers underscore the potential efficacy of specific FW treatments in enhancing plant growth, with VC 50% and FV 25% showing considerable promise in increasing crop yield. The study concludes that FW compost and vermicompost significantly enhance plant growth and soil quality, advocating for their use as sustainable and environmentally friendly alternatives to chemical fertilizers. The findings emphasize the importance of selecting appropriate fertilizer types and concentrations to optimize agricultural productivity and environmental sustainability, supporting the incorporation of FW into agricultural systems as a beneficial resource.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.

Effective waste elimination is critical for the success of construction projects. Although several studies have focused on various aspects of construction waste, limited efforts have investigated the dynamic effect of Making-Do (MD) practices on productivity, rework, defects, and materials wastage. From a lean construction perspective, this study aims to address MD waste using the Last Planner System (LPS) and BIM. First, the casual structure that can cause MD in construction projects was expressed in a casual loop diagram (CLD), and thematic analysis uncovered the strategies of LPS-BIM to eliminate MD identified by reviewing the literature. Secondly, twenty-five strategies from the LPS and BIM strategies to address MD using Structural Equation Modeling (SEM) were assessed. Subsequently, a system dynamics model (SDM) for investigating LPS-BIM strategies on MD decisions in a construction project was formulated based on the underlying causal loop diagrams and the mathematical relations among the variables. Finally, the model was applied to three projects, and simulations for four LPS-BIM scenarios were carried out. The findings show that dynamic interactions among diverse production planning and control factors are critical in evaluating MD impacts on a construction project. The results demonstrate that the LPS-BIM approach resulted in an average 43.8% reduction in the tasks performed with MD, 45.3% of constraints, 66.5% of construction waste, increasing 13.7% completion rate, and 29.3% cost reduction, demonstrating that LPS-BIM as a more efficient solution for MD mitigation and construction planning.

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

This paper responds to the research question, “can urban farming help Nepali cities become more sustainable”? Especially after the Covid-19 pandemic, urban residents have begun to realize that food transported from long distances could not always be reliable. Urban farming can help produce fresh food locally and avoid long-distance transportation, and refrigeration. This practice also helps reduce greenhouse gases through plant carbon use efficiency (CUE). Urban farming not only helps city-dwellers towards achieving self-reliance in food production but also in vegetation carbon dynamics (VCD) while supporting the circular economy. Urban farming consists of edible landscapes, which can also be an aesthetic public space. As urban lands command higher prices than agricultural land, urban farming usually happens on residential yards, roofs, balconies, community gardens, and dedicated areas in public parks. Rainwater harvesting, and redirecting can help irrigate urban farms which can be part of rain gardens. The national census of 2021 (CBS 2022, p5) identifies that 66 percent of Nepal’s population live in urban areas. However, the World Bank (2018), shows that only 21 of Nepal’s population was projected to live in urban areas in 2021. It is not debatable that the urbanization process in Nepal is on the rise. Thus, urban agriculture can play an important role to supplement the residents’ food needs. Many cities in Nepal have already successfully adapted to urban farming where residents grow food on their building site, balconies, and rooftop often growing plants on pots, vases, and other types of containers. The UN-Habitat, with the support of European Union and local agencies, has published a rooftop farming training manual (2014) showing the feasibility of urban farming in Nepal.The paper discusses how Public Private Partnership (PPP) can promote urban agriculture and make the process more effective and attractive to urban farming households. It also analyzes how a PPP approach also facilitates the use of better technology, advisory support, and use of research extension activities. This paper draws on literature review, secondary data (e.g., from National Census Nepal 2021) and authors’ professional experiences related to best practices in the areas to analyze the benefits and challenges related to urban farming in Arizona, USA. The paper will provide recommendations for Nepali cities to maximize the benefit provided by urban farming. It is expected to be useful to Nepali policy makers, and government agencies, and nonprofit organizations which promote sustainability, and organic farming.

Recent studies have demonstrated silk fibroin’s ability to extend the shelf life of foods by mitigating the hallmarks of spoilage, namely oxidation and dehydration. Due to the potential for this protein to become more widespread, its safety was evaluated comprehensively. First, a bacterial reverse mutation test (Ames test) was conducted in five bacterial strains. Second, an in vivo erythrocyte test was conducted with Sprague Dawley rats at doses up to 1,000mg/kg-bw/day. Third, a range-finder study was conducted with Sprague Dawley rats at the highest consumption amount given solubility and oral gavage volume constrains (500mg/kg-bw/day). Fourth, a 28-day study in Sprague Dawley rats was conducted at the 500mg/kg-bw/day amount. Fifth, an in vitro pepsin digestion assay was performed to assess the potential for protein allergenicity. Sixth, allergenic potential was further assessed using liquid chromatography-mass spectroscopy for detection of allergenic insect proteins. Seventh, the protein sequences were subjected to bioinformatic analyses. Together, these studies raise no mutagenic, carcinogenic, toxicological, or allergenic concerns with the oral consumption of silk fibroin.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

The demand for improving the nuclear waste management has since long been identified as one of the major hurdles for widespread use of nuclear energy. Nuclear waste management, through partitioning and transmutation (P&T) has been researched since the 1990ies with partitioning being a pre-requisite for the process. Recently, an innovative approach of reactors directly operating on spent nuclear fuel, iMAGINE, has been proposed which could deliver on the aims of P&T as a side effect to more efficient nuclear energy production in the future. The results shown here confirm that it is possible to achieve the aims of P&T without prior partitioning, but it is certainly less efficient since the high concentration of MAs, required for efficient burning, are impossible to obtain in a short operational time. The proposed nuclear waste management approach will be a long-term effort when it is accomplished without partitioning/separation technologies. However, none of the analyses contradicts this effort – the key points are a) when the technology for treating the waste is possible and reliable, the time horizon will not be a major concern b) the waste management is now intrinsically linked with energy production instead of requiring dedicated costly facilities, delivering a promising economic basis c) the waste management is now associated with long-term energy production and massively improved resource utilization. In summary, the objectives of P&T are achievable without prior partitioning – this is a ground-breaking result. However, the approach will require continued nuclear energy production for a very long time. In case of a nuclear phase-out decision, a much more efficient transmutation scenario would have to be envisaged as already discussed several years ago for Germany.

This article seeks to strengthen efforts in technological developments based on the classification of PET plastic that positively impacts sustainable development and contributes to suitable solutions in collection centers in Mexico. Three experiment designs and machine learning tools for data processing were developed. For the experimentation, three factors were considered: the bottle's size, the amount of liquids inside the bottle, and the label on the bottle. The first experiment was to identify the distance of the sensor from post-consumer PET bottles. The second experiment was to determine the detection ability of the sensor with different levels of liquids inside the bottles, and the third was to determine the detection ability on the bottle labels. A digital lux meter on a microcontroller was developed to monitor illuminance on post-consumer PET plastic when it contains liquid as it passes through a conveyor belt for processing at an average rate of three bottles per second. With the implemented methodology, liquids were satisfactorily detected inside the transparent PET bottles when they had beverages between 25% and 100% of their capacity. Finally, this paper highlights that it is possible to implement an affordable design to identify bottles with liquids for collection centers.