One-fifth of the world’s population and critical infrastructures are near the coast and regions at high risk of sea level elevation. Climate change is expected to increase coastal extreme events, rising sea levels, and impact on ecosystem. This paper reviews coastal physical processes, wave and impacts, and the introduction of nature-based models for the mitigation of flooding, erosion, and recovery. Hard engineering like seawalls has been used to prevent, protect, and control water-based environmental forces with an extended impact on the land. A nature-based engineering solution, such as growing vegetation, is being adopted as a sustainable solution to help make existing technology live its design life and provide climate change adaptation and resilience for coastal and riverine communities. This paper presents applications of seaweed farms as an advanced nature-based mitigation approach. The result of the experiments conducted at RWTH Aachen University on wave damping of seaweed types and farming structures to validate the hypothesis will be presented in part B. A soft engineering approach to designing future vegetated protection systems using seaweed as a nature-based solution can help existing coastal infrastructure design life and protect against climate-induced SLR rise and adaptation, coastal risk mitigation, ecosystem restoration, and blue bio-economic development.

The rapid development of quantum computing devices promises powerful machines with capabilities that solve a wide range of problems that traditional computers cannot. Therefore, quantum computers generate new threats at unprecedented speed and scale and specifically pose an enormous threat to encryption. Lattice-based cryptography is considered to be the rival to a quantum computer attack and the future of post-quantum cryptography. So, cryptographic protocols based on lattices have a variety of benefits, like security, efficiency, lower energy consumption, and speed. In this work, we study the most well-known lattice-based cryptosystems while a systematic evaluation and comparison is presented also, and focuses on their strengths and weaknesses.

Many assets of clinical medicine, such as clinical chemistry and diagnostic imaging, make clinical diagnosis outstanding compared to postmortem diagnosis. An assessment of functional status certainly has priority over the postmortem, cross-sectional use of diagnostic tests and laboratory equipment. In addition, the cost of these tools is sometimes steep, and their use does not always fit into a reasonable cost–benefit ratio. However, sometimes postmortem observations, such as inflammation, pulmonary edema, or infiltration and cerebral swelling, cannot be explained without implementing immunohistochemical markers for postmortem diagnosis. Introducing blood-based biomarkers in postmortem care could significantly reduce the rates of inconclusive postmortems and discrepancies in autopsy findings and clinical diagnoses. This is particularly relevant in the scope of vascular pathology, considering the great burden of vascular diseases in overall mortality. Expanding traditional autopsy with blood-based (circulating) biomarkers to avoid invasive postmortem examination would have cultural, religious, and potential economic advantages. All of the target molecules are discussed in the context of the process they up-regulate or down-regulate and which turns out to be the final cause of death. Ultimately, it is evident that further studies are needed to provide concrete validation for a combination of markers on a specific case order to reach a postmortem diagnosis with or without clinical records.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

The oncologic disease is a big global health issue that causes thousands of deaths annually, and it has a significant impact in the life quality of patients. Prostate cancer (PCa) is the second most diagnosed cancer and the fourth leading cause of cancer-related death in men in the western world. Delineation of pathogenetic pathways and key driver molecular alterations involved in PCa development has provided a roadmap for the evaluation of biomarkers in predicting disease outcome and to identify potential therapeutic targets. Chemotherapeutic agents introduced from the 1990s include the taxanes (paclitaxel, docetaxel and cabazitaxel), which are the most anticancer drugs used for PCa treatment. This review presents the current knowledge about the onset and development of PCa, state-of-art on the use of taxane-based therapy, and their combination with targeting different transmembrane oncoproteins in PCa. The silencing of some transmembrane proteins can improve taxane sensitivity, and therefore, may be a mechanism to improve the ef-fectiveness of these drugs in PCa treatment. This combined therapy needs to be explored as po-tential therapeutic agent for reducing cell proliferation, migration, and invasiveness in PCa.

Objective: To investigate the feasibility and preliminary effects of a 12-week home-based moderate intensity cycling programme in stroke survivors. Design: Single-blinded, parallel group, Randomised Controlled Trial Setting: Home-based Participants: Participants will be survivors of first-ever stroke and randomly assigned to an Active Cycling Group (ACG) or control group. Intervention: The ACG performed a 12-week home-based cycling programme, three sessions per week. Work intervals were executed at 75% of the maximal heart rate (HR_max), recovery intervals at 50% of HR_max. Work interval duration increased from three ten-minute intervals to 30 minutes continuous cycling. The control group completed a 12-week neurocognitive exercise programme. Main outcome measurements: Primary outcome measures are compliance with training, adherence to protocol and safety as measured by adverse events. Secondary outcome measurements included a: simplified modified Rankin Scale questionnaire (stroke severity), Six-Minute Walking Test (walking ability), Ten-meter Walk Test (walking ability), Rivermead Mobility Index (walking ability), graded submaximal cycling test (exercise capacity), Physical Activity for Individuals with Physical Disability questionnaire (physical activity), EQ-5D-5L (quality of life), Stroke Specific Quality of Life questionnaire (quality of life), Montreal Cognitive Assessment (cognition), General Self-Efficacy Scale (self-efficacy), and Exercise Self-Regulation Questionnaire (self-regulation).

Close to half (45.4%) of 2.3 million breast cancers (BC) diagnosed in 2020 were from Asia. While the burden of breast cancer has been examined on the level of broad geographic regions, literature on more in-depth coverage of the individual countries and subregions of the Asian continent is lacking. This review examines the breast cancer burden in 47 Asian countries. Breast cancer screening guidelines and risk-based screening initiatives are discussed.

ASEAN SME has a role as the regional socioeconomic stabilizer. This particular role is inseparable from endogenous multi-sector collaboration. Although, Indonesian SMEs were struggled in adopting Industry 4.0 correspond to digital infrastructure and digital literacy problems. This study evaluates Indonesian SME collaboration dynamics with government and technology startup (TS). The integration of agent-based model and causal loop simulation were employed to assess the TS collaboration impact on SME Industry 4.0 adoption and SME competition with larger competitors. The simulation results imply the SME collaboration with TS can lead to early adoption of Industry 4.0 which balances the business competition environment. The model also shows rising the government aid exponentially can help the SME to late adoption of Industry 4.0 which unable to sustain the SME in business competition. Thus, the developed integrative simulation model is a state-action planning model with each state result bounded to the previous state result that determined by initial input parameters. Conclusively, the model can be used as a resiliency planner for SME Industry 4.0 adoption.

After a long limbo, RNA has gained its credibility as a druggable target, fully earning its de-served role in the next-generation area of pharmaceutical R&D. We have recently probed the Trans-Activation Response element (TAR), a RNA stem–bulge–loop domain of the HIV-1 genome with bis-3-chloropiperidines (B-CePs), and revealed the compounds unique behavior in stabiliz-ing TAR structure, thus impairing in vitro the chaperone activity of the HIV-1 nucleocapsid (NC) protein. Seeking to elucidate the determinants of B-CePs inhibition, we have further characterized here their effects on the target TAR and its NC recognition, while developing quantitative analyti-cal approaches for the study of multicomponent RNA-based interactions.

Cadmium (II) contamination in the environment is an emerging problem due to its acute toxicity and mobility, so it is very urgent to remove this species from industrial wastewater before it is discharged into the environment. Thus, a starch-based activated carbon (AC) with a specific surface area of 1600 m2g-1 is used as an adsorbent for the capturing of toxic Cadmium (II) ions from synthetic solution. The sorbent is characterized by BET, SEM, TEM, XRD, FT-IR, TGA, and zeta potential. The maximum uptake (284 mg g-1) of Cadmium (II) ion is obtained at pH 6. The thermodynamics parameters like ∆G, ∆H, ΔS are found to be -17.42 kJmol-1, 6.49 kJ mol-1, and 55.66 Jmol-1K-1 respectively, revealing that the adsorption mechanism is endothermic, spontaneous, and feasible. The experimental data follows the D-R and Langmuir models well. The mass transfer is controlled by pseudo 2nd order kinetics. Furthermore, the density functional theory simulations demonstrate that the activated carbon strongly interacted with the Cd (II) ion through its various active sites. The adsorption energy noted for all interactive sites is highly negative (-0.45 eV to -10.03 eV), which shows that the adsorption process is spontaneous and stable which is in agreement with the experimental thermodynamics analysis.

Due to the continuing high suicide rates among young men, there is a need to understand help-seeking behaviour and engagement with tailored suicide prevention interventions. The aim of this study was to compare help-seeking among younger and older men who attended a therapeutic centre for men in a suicidal crisis. In this case series study, data were collected from 546 men who were referred into a community-based therapeutic service in North West England. Of the 546 men, 337 (52%) received therapy; 161 (48%) were aged between 18 and 30 years (mean age 24 years, SD=3.4). Analyses included baseline differences, symptom trajectories for the CORE-34 Clinical Outcome Measure (CORE-OM) and engagement with the therapy. For the CORE-OM there was a clinically significant reduction in mean scores between assessment and discharge (p<0.001) for both younger and older men. At initial assessment, younger men were less affected by entrapment (46% v 62%; p=.02), defeat (33% v 52%; p=.01), not engaging in new goals (38% v 47%; p=.02), and positive attitudes towards suicide (14% v 18%; p=.001) than older men. At discharge assessment, older men were significantly more likely to have an absence of positive future thinking (15% v 8%; p=0.03), have less social support (45% v 33%; p=.02) and feelings of entrapment (17% v 14%; p=.02) than younger men. Future research needs to assess the long-term effects of help-seeking using a brief psychological intervention for young men in order to understand whether the effects of the therapy are sustainable over a period of time following discharge from the service.

Substantial research is required to ensure that micro-mobility ride sharing provides a better fulfillment of user needs. This study proposes a novel crowdsourcing model for the ride-sharing system where light vehicles such as scooters and bikes are crowdsourced. The proposed model consists of three entities: suppliers, customers, and a management party responsible for receiving, renting, booking, and demand matching with offered resources. It can allow suppliers to define the location of their private e-scooters/e-bikes and the period of time they are available for rent. Using a dataset of over 9 million e-scooter trips in Austin, Texas, we ran an agent-based simulation six times using three maximum battery ranges (i.e., 35, 45, and 60 km) and different numbers of e-scooters (e.g., 50 and 100) at each origin. Computational results show that the proposed model is promising and might be advantageous to shift the charging and maintenance efforts to a crowd of suppliers.

Modern agent-based models (ABM) and other simulation models require evaluation and testing of many different parameters. Managing that testing for large scale parameter sweeps (grid searches) as well as storing simulation data requires multiple, potentially customizable steps that may vary across simulations. Furthermore, parameter testing, processing, and analysis are slowed if simulation and processing jobs cannot be shared across teammates or computational resources. While high-performance computing (HPC) has become increasingly available, models can often be tested faster through the use of multiple computers and HPC resources. To address these issues, we created the Distributed Automated Parameter Testing (DAPT) Python package. By hosting parameters in an online (and often free) "database", multiple individuals can run parameter sets simultaneously in a distributed fashion, enabling ad hoc crowdsourcing of computational power. Combining this with a flexible, scriptable tool set, teams can evaluate models and assess their underlying hypotheses quickly. Here we describe DAPT and provide an example demonstrating its use.

Due to the continuing high suicide rates among young men, there is a need to understand help-seeking behaviour and engagement with tailored suicide prevention interventions. The aim of this study was to explore help-seeking behaviour and engagement for young men aged 18 to 30 years who attended a therapeutic centre for men in a suicidal crisis. In this prospective cohort study, data were collected from 546 men who were referred into a community-based therapeutic service in North West England. Of the 546 men, 337 (52%) received therapy; 161 (48%) were aged between 18 and 30 years (mean age 24 years, SD=3.4). One third (n=54; 34%) of the men were seen within 48 hours of their referral. Analyses included baseline differences, symptom trajectories for the CORE-34 Clinical Outcome Measure (CORE-OM) and engagement with the therapy. For the CORE 34 there was a clinically significant reduction in mean scores between assessment and discharge (p<0.001), with all outcomes demonstrating a large effect size. Future research needs to assess the long-term effects of help-seeking using a brief psychological intervention for young men in order to understand whether the effects of the therapy are sustainable over a period of time following discharge from the service.

It’s always a challenge for a teacher to get their students to be more engaged or active in the classroom. Engagement happens when students are interested in the subject, have fun, and feel welcome in the classroom. But how do we make students more engaged? To make this happen, Educational escape rooms were introduced into studies. In this paper, we will discuss about the creation and evaluation of educational escape rooms within an engineering learning context. As part of our research project, four educational escape rooms were created for students and surveys were conducted among them to evaluate the success of our project. Our findings indicate that the escape room learning model is well accepted by the students. As a result of the activity, high levels of dedication and enthusiasm are recorded and students shows the eagerness to do more escape room activities.

In some parts of Nigeria, many girls do not attend school, and among those sent to school, many still drop out early. This and other socio-cultural factors affect girls psychologically. There is no doubt that girls need consistent love and tutoring to guide them through the turbulent teen years and beyond. They need a mentor who acts as a friend and a role model. The Mobile-based Mentoring Platform seeks to leverage on mobile technology's affordances to focus on the needs of the girl-child, such as improvement in academic achievement, guidance in career choice, development of self-concept, and esteem. The girl-mentees comments revealed that using the platform provided them frequent access to mentors and access to learning opportunities. The challenges they faced include epileptic internet network, intrusions by parents, and others. Therefore, this paper examined the challenges and benefits of mentoring girls via a mentoring platform.

Course-based undergraduate research experiences (CUREs) provide students with opportunities for the same gains that apprenticed research with faculty members offer. As their popularity increases, it is important that critical elements of CUREs are supported by thoughtful design. Student experiences in CUREs can provide important insights into why CUREs are so effective. We present evidence from students who participated in CUREs at the introductory, intermediate, and advanced levels, as well as from graduate teaching assistants for an introductory lab course that included a CURE. Students and teaching assistants describe repetition as a valuable element in CUREs and other laboratory experiences. We used student work and open-ended interviews to identify which of five previously described elements of CUREs students found important. Because repetition was particularly salient, we characterized how students described repetition as they experienced it in courses that contained full-length or “micro”-CUREs. In prompted interviews, students described how repetition in CUREs provided cognitive (learning concepts) and practical (learning technical skills) value. Recent graduates who had participated in CUREs at each level of their Biology education were particularly aware that they placed value in repetition and acknowledged it as motivational in their own learning. Many students described repetition in metacognitive terms, which also suggests that as students advance through laboratory and CURE curricula, their understanding of how repetition supports their learning becomes more sophisticated. Finally, we integrated student descriptions to suggest ways in which repetition can be designed into CUREs or other laboratory courses to support scientific learning and enhance students’ sense of scientific identity.

Starting from the importance of risk perception for taking certain preventive measures to protect people and their property from disasters, the subject of the research is to examine the factors influencing public perception of mythically-based human behavior in disaster conditions. Using the random sampling method, 250 adult respondents were surveyed in the city of Belgrade, using a specially created and adapted survey questionnaire. The results of the research show that there is no statistically significant influence of gender, age, educational and economic factors on the public perception of human behavior in disaster conditions. The results of the research can be used to improve strategies and campaigns based on risk assessment, aimed at improving the safety of people in disasters.

High levels of meat consumption are increasingly being criticised for ethical, environmental, and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein in comparison to meat. This alternative offers several social, environmental and health benefits and may play a role in reducing meat consumption. However, there has been a lack of research on how specific meat substitute attributes can influence consumers to replace or partially replace meat in their diets. Research demonstrates that in many countries consumers are highly attached to meat. They consider it as an essential and integral element of their daily diet. For these consumers which are not interested in vegan or vegetarian alternatives to meat, so-called meathybrids could be a low-threshold option for a more sustainable food consumption behaviour. In meathybrids only a fraction of the meat product (e.g. 20% to 50%) is replaced with plant-based proteins. In this paper, the results of an online survey with 501 Belgium consumers are presented with focus on preferences and attitudes relating to meathyrids. The results show that more than fifty percent of consumers substitute meat at least occasionally. Thus, about half of the respondents reveal an eligible consumption behaviour in respect to sustainability and healthiness to a certain degree. Concerning the determinants of choosing either meathybrid or meat it becomes evident that a strong effect is exerted by the health perception. The healthier meathybrids are perceived, the higher is the choice probability. Thus, this egoistic motive seems to outperform altruistic motives like animal welfare or environmental concerns when it comes to choice for this new product category.

High levels of meat consumption are increasingly being criticised for ethical, environmental, and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein that, in comparison to meat, offer a number of social, environmental and health benefits and may play a role in reducing meat consumption. However, there has been a lack of research on the role they can play in the policy agenda and how specific meat substitute attributes can influence consumers to replace partially replace meat in their diets.

High levels ofmeat consumption are increasingly being criticised for ethical, environmental, 2 and social reasons. Plant-based meat substitutes have been identified as healthy sources of protein in 3 comparison to meat. This alternative offers several social, environmental and health benefits and may 4 play a role in reducing meat consumption. However, there has been a lack of research on how specific 5 meat substitute attributes can influence consumers to replace or partially replace meat in their diets. 6 Research demonstrates that in many countries consumers are highly attached to meat.They consider 7 it as an essential and integral element of their daily diet. For these consumers which are not interested 8 in vegan or vegetarian alternatives to meat, so-called meathybrids could be a low-threshold option 9 for a more sustainable food consumption behaviour. In meathybrids only a fraction of the meat 10 product (e.g. 20% to 50%) is replaced with plant-based proteins. In this paper, the results of an online 11 survey with 500 German consumers are presented with focus on preferences and attitudes relating 12 to meathyrids. The results show that more than fifty percent of consumers substitute meat at least 13 occasionally. Thus, about half of the respondents reveal an eligible consumption behaviour in respect 14 to sustainability and healthiness to a certain degree. Concerning the determinants of choosing either 15 meathybrid or meat it becomes evident that the highest effect is exerted by the health perception. The 16 healthier meathybrids are perceived, the higher is the choice probability. Thus, this egoistic motive 17 seems to outperform altruistic motives like animal welfare or environmental concerns when it comes 18 to choice for this new product category.

Latin binomials, popularised in the eighteenth century by the Swedish naturalist Linnaeus, have stood the test of time in providing a stable, clear and memorable system of nomenclature across biology. However, relentless and ever-deeper exploration and analysis of the microbial world has created an urgent unmet need for huge numbers of new names for Archaea and Bacteria. Manual creation of such names remains difficult and slow and typically relies on expert-driven nomenclatural quality control. Keen to ensure the legacy of Linnaeus lives on in the age of microbial genomics and metagenomics, we propose an automated approach, employing combinatorial concatenation of roots from Latin and Greek to create linguistically correct names for genera and species that can be used off the shelf as needed. As proof of principle, we document over a million new names for Bacteria and Archaea. We are confident that our approach provides a road map for how to create new names for decades to come.

Universitas Sebelas Maret (UNS) through SMART UNS Company has conducted research and development of e-motorcycle conversion using Li-ion battery pack as a substitute for ICE energy source from the conventional motorcycle. Currently, the battery-pack that used for e-motorcycle conversion is in the development phase towards commercialization. The challenge of estimating production costs is the complicated production process and storing hidden expenses that can be a problem. This hidden cost is often a missing or varied factor that costs less or more expensive. This study presents an integrated parametric cost estimation model with activity-based cost assignments to estimate production costs through cost calculations for each activity. Activity-based costs break the production process into a specific cost element for each step. Each activity's cost is put into a parametric cost estimation model to calculate the cost of each activity into the total cost of production. Cost estimation results will be analyzed using a regression method to determine which variables most affect the production cost of Li-ion battery packs for the conversion of e-motorcycles in the SMART UNS company.

Coronavirus, also known as COVID-19, has been declared a pandemic by the World Health Organization (WHO). At the time of conducting this study, it had recorded over 1.6 million cases while more than 105,000 have died due to it, with these figures rising on a daily basis across the globe. The burden of this highly contagious respiratory disease is that it presents itself in both symptomatic and asymptomatic patterns in those already infected, thereby leading to an exponential rise in the number of contractions of the disease and fatalities. It is therefore crucial to expedite the process of early detection and diagnosis of the disease across the world. The case-based reasoning (CBR) model is an effective paradigm that allows for the utilization of cases’ specific knowledge previously experienced, concrete problem situations or specific patient cases for solving new cases. This study therefore aims to leverage the very rich database of cases of COVID-19 to solve new cases. The approach adopted in this study employs the use of an improved CBR model for state-of-the-art reasoning task in classification of suspected cases of Covid19. The CBR model leverages on a novel feature selection and semantic-based mathematical model proposed in this study for case similarity computation. An initial population of the archive was achieved with 68 cases obtained from the Italian Society of Medical and Interventional Radiology (SIRM) repository. Results obtained revealed that the proposed approach in this study successfully classified suspected cases into their categories at an accuracy of 97.10%. The study found that the proposed model can support physicians to easily diagnose suspected cases of Covid19 base on their medical records without subjecting the specimen to laboratory test. As a result, there will be a global minimization of contagion rate occasioned by slow testing and as well reduce false positive rates of diagnosed cases as observed in some parts of the globe.

Visualization of the seabed terrain is one of the key functions of marine geographic information system. The major challenge here is that the obtained data for seabed terrain usually consists of elevation and sediment only but does not include remote sensing images, which is important for ground terrain visualization, as they can be used as textures to reveal detailed information and achieve realistic visual results. Existing seabed terrain visualizing methods (including annotations, color-mapping, and texture-mapping) have limitations in reality and intuition, as they are inadequate to express the physical characteristics of sediment accurately. This paper presents a novel and advanced 3D visualization method of seabed terrain, which introduces the Physically Based Rendering (PBR) theory into the field of geographic visualization. We analyze the main categories of seabed sediments and their optical features respectively, then develop a procedural method to generate physically based rendering materials for different sediments. Then an enhanced bidirectional reflectance distribution function is employed to achieve accurate and intuitive terrain rendering. We also refine the texture sampling method and propose a procedural seabed objects generation method to construct a more natural and realistic undersea environment. Experimental results reveal our method can make good use of the limited seabed terrain data and get significant improvements in visual effect, which can help users to cognize and analyze the seabed geographic environment more accurately and intuitively.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

Previously, we described the initial use of Flipped Team‐Based learning (FTBL) defined as TBL approach combined with flipped classroom learning methodology, in which students previewed online lectures and applied their knowledge in different in-class activities. The purpose of the present study is to review the progress within this approach and to investigate how constant changes in team allocation can affect student’s perception regarding this modified FTBL approach. Although students showed reluctance initially to get out of their ‘comfort zone’, our findings show that learners perceived the adoption of the continued random allocation, and became accustomed to this learning approach, which finally assisted them to enhance their team-work skills and classroom performance, to develop their reflective capabilities as well as improving their rapport building skills, learning and academic performance. Learners also believed that this learning strategy that creates critical incidents can simulate their future work environment as they might be expected to work in unfamiliar situations. Therefore, the present study indicated strong support for the modified FTBL method and was seen to work exceptionally well, despite some minor problems that students can experience working in a team and/or with different teammates in every session.

The effect of microstructure and chemistry of passive films on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys was also investigated employing Tafel extrapolation and dynamic electrochemical impedance spectroscopy. Corrosion studies were performed in 0.9% NaCl solution at 37 oC, and the obtained results were compared with ultrapure Ti (99.99%). The different phases of the microstructure were characterized by X-ray diffraction and scanning electron microscopy. Chemical composition and chemistry of the corroded surfaces were studied using X-ray photoelectron analysis. For all studied alloys, the microstructure consisted of α matrix, which was strengthened by β phase. The highest and the lowest values of the β phase’s volume fraction were recorded for TC21 and Ti-Al-Nb alloys, respectively. The uniform corrosion rate and pitting corrosion resistance (R_pit) of the studied alloys were enhanced following the sequence: Ti-6Al-7Nb < Ti-6Al-4V << TC21. The corrosion resistance of Ti-Al-Nb alloy approached that of pure Ti. The obvious changes in the microstructure of these alloys, together with XPS findings, were adopted to interpret the pronounced variation in their corrosion rates.

Bangladeshi construction industry suffers a lot of safety and accidental issues than other developing countries in the world. Among many of these, accident of construction project goes far beyond and shape a horrific figure of death for every year. The aims of this study is that analysis and discussion of causes of accident at construction project in Bangladesh. A widespread statistical data collection and data analysis take place to identify the causes and design the questionnaire. The questionnaire-based survey was used to elicit the attitude of four stakeholders as workers, owners, consultants, and contractors towards passive causes of fatal accident at construction site. These study also identify 77 passive causes under 14 major groups and ranked them based on Relative Importance Index (RII). The top 5 major group of causes are (1) Management related, (2) Consultant related, (3) Technology related, (4) Labour related and (5) Contractor related. The top 5 passive causes are: (1) Unaware of safety-related issue, (2) Lack of personal protective equipment, (3) Lack of safety eliminating/ avoiding design, (4) Unfit equipment, (5) Lack of knowledge and training on equipment.

Portfolio weights solely based on risk avoid estimation error from the sample mean, but they are still affected from the misspecification in the sample covariance matrix. To solve this problem, we shrink the covariance matrix towards the Identity, the Variance Identity, the Single-index model, the Common Covariance, the Constant Correlation and the Exponential Weighted Moving Average target matrices. By an extensive Monte Carlo simulation, we offer a comparative study of these target estimators, testing their ability in reproducing the true portfolio weights. We control for the dataset dimensionality and the shrinkage intensity in the Minimum Variance, Inverse Volatility, Equal-risk-contribution and Maximum Diversification portfolios. We find out that the Identity and Variance Identity have very good statistical properties, being well-conditioned also in high-dimensional dataset. In addition, the these two models are the best target towards to shrink: they minimise the misspecification in risk-based portfolio weights, generating estimates very close to the population values. Overall, shrinking the sample covariance matrix helps reducing weights misspecification, especially in the Minimum Variance and the Maximum Diversification portfolios. The Inverse Volatility and the Equal-Risk-Contribution portfolios are less sensitive to covariance misspecification, hence they benefit less from shrinkage.

Some contaminants of emerging concern (CECs) are known to survive conventional wastewater treatment plants, which introduce them back to the environment and can potentially cycle up in drinking water supplies. This is especially concerning because of the inherent ability of some CECs to induce physiological effects in humans at very low doses. Advanced oxidation processes (AOPs) such as TiO2 based photocatalysis are of prominent interest for addressing CECs in aqueous environments. Natural water resources often contain dissolved metal cations concentrations in excess of targeted CEC concentrations. These cations may significantly, adversely impact degradation of CECs by scavenging TiO2 surface generated electrons. Consequently, simple pseudo first order or Langmuir-Hinshelwood kinetics are not sufficient for reactor design and process analysis in some scenarios. Rhodamine B dye and dissolved copper cations were studied as reaction surrogates to demonstrate that TiO₂ catalyzed degradation for very dilute solutions is very nearly completely due to homogeneous reaction with hydroxyl radicals and that in this scenario the hole trapping pathway has negligible impact. Chemical reaction kinetic studies were then carried out to develop a robust model for RB/metal reactions that is exact in the electron pathways for hydroxyl radical production and metal scavenging.

To date, several independent methods and algorithms exist exploiting constraint-based stoichiometric models to find metabolic engineering strategies that optimize microbial production performance. Optimization procedures based on metaheuristics facilitate a straightforward adaption and expansion of engineering objectives as well as fitness functions, while being particularly suited for solving problems of high complexity. With the increasing interest in multi-scale models and a need for solving advanced engineering problems, we strive to advance genetic algorithms, which stand out due to their intuitive optimization principles and proven usefulness in this field of research. A drawback of genetic algorithms is that premature convergence to sub-optimal solutions easily occurs if the optimization parameters are not adapted to the specific problem. Here, we conducted comprehensive parameter sensitivity analyses to study their impact on finding optimal strain designs. We further demonstrate the capability of genetic algorithms to simultaneously handle (i) multiple, non-linear engineering objectives, (ii) the identification of gene target-sets according to logical gene-protein-reaction associations, (iii) minimization of the number of network perturbations, and (iv) the insertion of non-native reactions, while employing genome-scale metabolic models. This framework adds a level of sophistication in terms of strain design robustness, which is exemplarily tested on succinate overproduction in Escherichia coli.

Background: Few studies have investigated the longitudinal association between cervical spondylosis (CS) and migraine by using a nationwide population-based database. Methods: We conducted a retrospective cohort study from 2000 to 2011 identifying 27,930 cases of cervical spondylosis and 111,720 control subjects (those without cervical spondylosis) from a single database. The subjects were frequency-matched on the basis of sex, age, and diagnosis date. The non- cervical spondylosis cohort was four times the size of the cervical spondylosis cohort. To quantify the effects of cervical spondylosis on the risk of migraine, univariate and multivariate Cox proportional hazard regression analyses were used to calculate the hazard ratio (HR) and 95% confidence interval (CI). Results: After a 10-year follow-up controlling for potential confounding factors, overall migraine incidence was higher in the cervical spondylosis cohort than in the non- cervical spondylosis cohort (5.16 and 2.09 per 1,000 people per year, respectively; crude hazard ratio = 2.48, 95% confidence interval = 2.28–2.69) with an adjusted hazard ratio of 2.03 (95% confidence interval = 1.86–2.22) after accounting for sex, age, comorbidities, and medication. Individuals with myelopathy in the cervical spondylosis cohort had a 2.19 times (95% confidence interval = 1.80–2.66) higher incidence of migraine compared than did those in the non- cervical spondylosis cohort. Conclusion: Individuals with cervical spondylosis exhibited a higher risk of migraine than those without cervical spondylosis. The migraine incidence rate was even higher among individuals with cervical spondylotic myelopathy.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

Big data has revolutionised science and technology leading to the transformation of our societies. High Performance Computing (HPC) provides the necessary computational power for big data analysis using artificial intelligence and methods. Traditionally HPC and big data had focused on different problem domains and had grown into two different ecosystems. Efforts have been underway for the last few years on bringing the best of both paradigms into HPC and big converged architectures. Designing HPC and big data converged systems is a hard task requiring careful placement of data, analytics, and other computational tasks such that the desired performance is achieved with the least amount of resources. Energy efficiency has become the biggest hurdle in the realisation of HPC, big data, and converged systems capable of delivering exascale and beyond performance. Data locality is a key parameter of HPDA system design as moving even a byte costs heavily both in time and energy with an increase in the size of the system. Performance in terms of time and energy are the most important factors for users, particularly energy, due to it being the major hurdle in high performance system design and the increasing focus on green energy systems due to environmental sustainability. Data locality is a broad term that encapsulates different aspects including bringing computations to data, minimizing data movement by efficient exploitation of cache hierarchies, reducing intra- and inter-node communications, locality-aware process and thread mapping, and in-situ and in-transit data analysis. This paper provides an extensive review of the cutting-edge on data locality in HPC, big data, and converged systems. We review the literature on data locality in HPC, big data, and converged environments and discuss challenges, opportunities, and future directions. Subsequently, using the knowledge gained from this extensive review, we propose a system architecture for future HPC and big data converged systems. To the best of our knowledge, there is no such review on data locality in converged HPC and big data systems.

Decades of research suggest that Mindfulness-Based Stress Reduction (MBSR) training supports a greater capacity to live with chronic medical conditions and contributes to lowering stress levels. This paper introduces a model for a Mindfulness-Based Recovery from Stroke (MBRfS) for promoting stroke recovery, informed by the lived experience of the author (a stroke survivor and certified MBSR instructor), the research literature regarding MBSR training, and the specific challenges of stroke recovery. Four themes emerged from the autoethnographic analysis that informed the proposed model: Readiness to accept the stroke event and the acquired brain injury; Navigating uncertainties of stroke recovery with awareness and self-responsibility for outcomes; Trusting the inherent wisdom of the body as a stroke recovery “teacher”; and Increased capacity to integrate complex emotions with self-compassion, and a sense of wholeness. A four component MBRfS model is offered, which consists of an integration amongst a modified MBSR framework, emergent attitudinal themes, and insights from the autoethnographic vignettes. The MBRfS model offers a path for providing participants with a supportive experience within stroke recovery. Recommendations and suggestions for future studies are offered to support the development of MBRfS for stroke survivors and their caregivers, as well as contributing to health care providers.

The main objective of this study is to analyze the impact of investment in Research & Development on the performance and value of companies, that is, to try to explain how R&D investment influences the companies’ performance. For this purpose, a dynamic panel data model was estimated using the Generalized Method of Moments, which made possible to measure the impact of R&D investment on performance through the Return on Operating Assets ratio for the Portuguese companies that invested the most between 2012 to 2019. The results show that the investment in R&D is not statistically significant in explaining the operating return on assets. However, the lagged financial performance in one period, the leverage, the asset turnover ratio and the accounts payable turnover show to have impact on the variable under study.

Manufacturing firms need to streamline their initiatives in line with 17 sustainable development goals (SDGs) 2030 as a means for improving performance. This research adapts SDG’s goals 8 decent job and economic growth’ as a measure of performance, in examine the effect of corporate sustainability strategies on performance of manufacturing firms. Census sampling technique was used in cross sectional survey of 900 multi-industry managers from one hundred and fifty (150) manufacturing firms in Kano, Nigeria. A five Likert scale, well-structured questionnaire was used in collecting data, analysed by Structural Equation Modelling SEM PLS Package. The study shows positive and significant effect of eco-efficiency, and positive and insignificant effect of both legitimation and risk mitigation strategies on performance respectively. The study concluded that the positive and significant effects of eco efficiency initiatives could be due to benefits derived from total quality management system, energy monitoring, and process safety management reflected in sustainability oriented visionary leadership of the managers. The positive and insignificant effects of legitimation initiatives could be as a result of huge spending on sustainability reporting, and corruption. The positive and insignificant effect of risk mitigation could be due to pro-activeness of the firms’ managers in tackling risk through sustainability oriented visionary leadership. The study recommended firms should adopt conservative eco-efficiency initiatives for improving performance and stop adopting extroverted legitimation and introverted risk mitigation strategies as both have no significant effect on performance. Future researchers should use longitudinal research design using financial metrics adopting the same independent variables in other economic sectors.

Recently, environmental degradation has become an international issue due to the extensive economic activities around the globe. This aspect demands the policymakers' and new researchers’ emphasis. Hence, the present article examines the impact of corporate social responsibilities (CSR) to community and environment on the environmental performance (ENP) of the manufacturing industry in China. The article also investigates the mediating role of green innovation and environmental strategy among CSR to community, CSR to environment and ENP of manufacturing industry in China. The article gets the primary data from the selected employees of the manufacturing industry using questionnaires. The article also tests the data's validity and reliability, and association among variables using smart-PLS. The outcomes indicated that CSR to environment has a positive association with ENP. The outcomes also revealed that green innovation and environmental strategy significantly mediate among CSR to community, CSR to environment and ENP. The article guides the policymakers in making policies related to improve ENP using CSR to environment and green innovation.

Non-impregnated small pore graphite (NSPG) with the compact microstructure for using in molten salt reactors (MSR) was prepared by the novel process, and the pore diameter of the obtained graphite was reduced to ~800 nm. The irradiation evaluation of the prepared graphite was carried out by 7 MeV Xe26+ ion irradiation and the microstructural changes of the graphite were investigated with IG-110 as a comparison. The graphitization degree of NSPG was higher than that of IG-110, though it was not subjected to an impregnation process. Under low-dose ion irradiation (

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The study evaluated the impact of supplementing ZH in combination with D3 on growth performance, energy efficiency, carcass traits, and meat quality of feedlot lambs. Thirty-two Dorper x Katahdin cross lambs (37.3±5.72 kg) were utilized in a 29 d experiment in a complete randomized block design with a 2x2 factorial structure consisting of two levels of ZH for 26 d (0 and 0.20 mg /kg PV-1) and two levels of D3 for 7 d (0 and 1.5x106 IU/d-1). ZH improved (P≤0.05) average daily gain (ADG) and feed efficiency by 9.9% and 17.8%, respectively, as well as hot carcass weight (HCW) and dressing carcass by 4.3% and 2.6%, respectively. (p≤0.03). However, ZH increased (p<0.01) muscle pH and Warner-Bratzler shear force (WBSF) (2.5 and 23.0%, respectively). D3 supplementation negatively affected (P≤0.02) dry matter intake (DMI) (last 7 d) and ADG by 15.7% and 18.1%. On the other hand, D3 improved the pH of the longissimus muscle (LM) by 1.7% (p=0.03) without affecting WBSF. When D3 was supplemented in combination with ZH, it was observed that meat quality was improved by reducing muscle pH compared to lambs treated only with ZH. However, D3 did not improve meat tenderness produced by ZH supplementation.

Abstract: Social media has become a vital tool in ensuring productivity among Undergraduates, as studies have shown an increased number of users globally. This study assessed the impact of social media usage on undergraduates’ academic performance and working memory. Participants from three different universities such as the University of Georgia (UG), Eastern European University (EEU), and Batumi State University (BSU) completed this study using online google forms. UG and EEU are in the capital city, and BSU is in Batumi City. The study questionnaires were approved by the institutional review board before the data collection. Descriptive analyses were assessed for all study populations, characteristics, frequencies, percentages, means, and standard deviations using Statistical Package for Social Science (SPSS Inc., Chicago, IL, version 25.0 for Windows) software. 41.3% were male students, as most of the participants were foreign students living and studying in Georgia. Male students had the risk of ‘conflict’ with families and friends because of social media. Female students are at increased risk of using social media as an ‘escape’ from negative feelings. 89.7% of students that perform physical activities, considering their academic workload had the risk of preoccupation complaints. 87.9% felt dissatisfied regularly because they wanted to spend more time on social media. Utilization of social media differed based on the characteristics of the participants such as age, gender, and geography. We observed the increase in prevalence of social media addiction, its effect on academic performance and working memory among undergraduate students.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

UNESCO highlights socio-emotional, cognitive, and behavioral learning as critical for advancing sustainability. As major events, sports generate significant social, economic, and environmental impacts. This study analyzed how academic background, gender, age, sport type, and modality influenced elite Colombian Olympic and Paralympic athletes' socio-emotional competencies. Methods: Colombian elite athletes who were members of the “Support to the Excellence Coldeportes Athlete” participated in the study. The total population studied included 334 Colombian elite athletes: mean age 27.10 ± 6.57 years old with 13.66 ± 6.37 years practicing his/her sports modality. The socio-emotional competencies of the participants were assessed using the Socio-emotional Competencies Scale (SECS). Results: Men scored higher in interpersonal regulation, self-awareness, conflict resolution, and emotional regulation. Younger athletes (≤25 years) had higher self-consciousness. Individual versus team sports did not differ. Paralympians showed higher motivation, self-awareness, teamwork, and emotional regulation. University educated athletes scored higher in motivation, self-awareness, teamwork, and empathy. All competencies positively correlated. Conclusion: Individualized interventions targeting improved socio-emotional performance are vital for sustainability and should account for differences across gender, age, education, and disability status.

Understanding the implications of organic acids in animal diets on physiological markers is critical for developing viable strategies for improving overall health and performance. The aim of this study was to evaluate the influence of dietary organic acids inclusion on rabbits’ growth performance and physiological status by determining blood and intestine development indicators. Forty weaned rabbits aged 28-d randomly assigned into 2 groups and fed with standard compound diet (SCD) and SCD + 0.2% organic acids mixture (butyric, propionic, sorbic; OAM). Growth performance was evaluated between 28-77 d of age, physiological status at 77 d of age. OAM’s rabbits final body weight, ADG, DFI, growth rate indicators were higher, but FCR lower compared to SCD (P &lt; 0.05). OAM increased total protein and albumin levels in blood plasma; reduced pH, increased DM, achieved greater viscosity in caecum’s content (P &lt; 0.05). Compared to SCD better gut development observed in OAM, as total intestinal weight was significantly higher (P &lt; 0.05). Acetic and propionic acids concentrations were increased, but butyric reduced in OAM caecum’s content (P &lt; 0.05). OAM had significant effect on the most caecum histomorphometric parameters: increased villus height, crypt depth and their ratio (P &lt; 0.05). According to our results OAM can improve rabbits’ growth performance, nutrient intake, and feed digestibility by significantly improving physiological status.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

Disease detection and prediction have been one of the most frequent uses of machine learning models in the last decade, and Parkinson's disease is no exception. It is common for people in their old age to have one form of disease or another depending on the circumstances in which they find themselves. This study analyzed and evaluated various supervised machine learning models to detect the presence of Parkinson's disease in elderly individuals. An extreme gradient boosting model, along with other models, such as naïve Bayes, random forest, K-nearest neighbor, and support vector machine (SVM), was implemented to determine the best outcome. The extreme gradient boosting (XGBoost) model is a powerful boosting machine learning technique, particularly in terms of speed and accuracy. The results showed that the XGBoost model, which is an optimized version of the other boosting models, is capable of projecting the presence of Parkinson's disease with very high accuracy compared to other algorithms. The implemented classification algorithm extreme gradient boosting method achieved approximately 98 % accuracy, 97.5 % precision, 100.0 % recall, and 98.7% f1-score which are high compared with the results found in the existing literature.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

This research addresses the respiratory distress syndrome (RDS) in preterm newborns, caused by insufficient surfactant synthesis, which can lead to serious complications, including pneumothorax, pulmonary hypertension, and pulmonary hemorrhage, increasing the risk of a fatal outcome. By analyzing chest radiographs and blood gases, we specifically focus on the significant contributions of these parameters to the diagnosis and analysis of the recovery of patients with RDS. The study involved 32 preterm newborns, and the analysis of gas parameters before and after the administration of surfactants and inhalation corticosteroid therapy revealed statistically significant changes in values of parameters such as FiO2, pH, pCO2, HCO3 and BE (Sig.&lt;0.05), ehile the pO2 parameter showed a potential change (Sig.=0.061). Parallel to this, the research emphasizes the development of a lung segmentation algorithm implemented in the MATLAB programming environment. The key steps of the algorithm include preprocessing, segmentation, and visualization for a more detailed understanding of the recovery dynamics after RDS. These algorithms have achieved promising results, with a global accuracy of 0.93±0.06, precision 0.81±0.16 and an F-score of 0.82±0.14. These results highlight the potential application of algorithms in the analysis and monitoring of recovery in newborns with RDS, also underscoring the need for further development of software solutions in medicine, particularly in neonatology, to enhance the diagnosis and treatment of preterm newborns with respiratory distress syndrome.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

In recent years, Neural networks are increasingly deployed in various fields to learn complex patterns and make accurate predictions. However, designing an effective neural network model is a challenging task that requires careful consideration of various factors, including architecture, optimization method, and regularization technique. This paper aims to comprehensively overview the state-of-the-art artificial neural network (ANN) generation and highlight key challenges and opportunities in machine learning applications. It provides a critical analysis of current neural network model design methodologies, focusing on the strengths and weaknesses of different approaches. Also, it explores the use of different learning approaches, including convolutional neural networks (CNN), deep neural networks (DNN), and recurrent neural networks (RNN) in image recognition, natural language processing, and time series analysis. Besides, it discusses the benefits of choosing the ideal values for the different components of ANN, such as the number of Input/output layers, hidden layers number, activation function type, epochs number, and model type selection, which help improve the model performance and generalization. Furthermore, it identifies some common pitfalls and limitations of existing design methodologies, such as overfitting, lack of interpretability, and computational complexity. Finally, it proposes some directions for future research, such as developing more efficient and interpretable neural network architectures, improving the scalability of training algorithms, and exploring the potential of new paradigms, such as Spiking Neural Networks, quantum neural networks, and neuromorphic computing.

The study investigates the effect of corporate governance characteristics on the financial performance of 124 Indian-listed companies that have undergone mergers and acquisitions during 2014–2020. It employs several performance measures, such as short-term capital market performance, long-term capital market performance, accounting-based and market-based measures, and firm-level control factors. The study found board size to be a positive and significant factor affecting short-term market performance. Further, it also documents weak linkages with other corporate governance variables like board independence, CEO duality, etc. Regarding control variables, leverage, the company's age, price-to-book ratio, and research and development expenses significantly impact the acquiring companies' financial returns. The study's findings add to our understanding of corporate governance's impact on performance in cases such as mergers and acquisitions.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

Affected by the COVID-19 and the international development pattern, the international environment has undergone profound changes, and enterprises, as the main body of activities rushing in the front line of production and operation and the main battlefield of market competition, are facing various risk challenges in the domestic and international markets. For theoretical research, the impact of organizational change on employee innovation performance has become a key issue in organizational behavior and human resource management research. However, the influence mechanism of organizational change on employee innovation performance is still unclear. In this study, we examine whether, how, and when organizational change increases employee innovation performance in accordance with job demands-resource theory, as well as the effect of work pressure and work engagement on employee innovation performance. Data from 289 employees at three time points are examined. The results show that: (1) Organizational change negatively affects employee innovation performance through work pressure, i.e., work pressure mediates the impact of organizational change on employee innovation performance. (2) Organizational change positively affects employee innovation performance through work engagement, i.e., work engagement mediates the impact of organizational change on employee innovation performance. (3) Organizational identity plays a moderating role between organizational change and work pressure and work engagement, respectively, and there is a moderating effect in the process of mediation of work pressure and work engagement. The findings of this study provide important insights into how and when organizational change influences employee innovation performance.

In this paper, to make the missile intercept the maneuvering target, the parallel approaching guidance law is developed. In order to estimate the target maneuver more accurately and reduce that’s influence on guidance accuracy, the distance-scalar disturbance observer is employed. Specifically, the estimation accuracy of the observer designed is regardless of the relative distance. The finite-time prescribed performance is employed to ensure that the line-of-sight angular rate is capable of converging to a predesigned small region in the specified finite time. All signals of interception system can guarantee ultimately uniformly boundedness proved by the Lyapunov stability theory. Finally, the availability of the parallel approaching guidance law is demonstrated by the numerical simulation.

The Sustainable Development Goals (SDGs) require collaboration among academia, indus-try, citizens, public administration and politics. Analysis and monitoring of the SDGs is a deci-sive step in evaluating possible corrective actions. In this regard, this paper assesses the perfor-mance of Italian regions in 2021 compared to the values recorded in 2020. An online survey among academics aims to support Multi-criteria decision analysis (MCDA) choices, which aims to calculate a sustainability score for Italian regions. The results, based on 27 targets, show that the northern regions show better performance, with the province of Trento topping the list. This is followed by Valle d'Aosta and the province of Bolzano, confirming the trio that emerged in the previous year. A very interesting fact is the growth of the central regions, which overall tend to reach a value close to that of the northern regions. In particular, Toscana, Marche and Lazio stand out for a good performance. It is also confirmed that the southern regions occupy the last places in the ranking with the only excep-tion being Abruzzo. The implications of this paper move toward a pragmatic approach that goes beyond the ideological in order to arrive at solutions and projects that are viewed with sharing by stake-holders. There is a need to foster collaboration between different territorial realities in order to achieve a social community in which young people have a role in which they can grow and share their ideas. Made in Italy is a target on which to enhance the SDGs to help make the Medi-terranean area a crossroads of the future global economy.

During shearer operation, piston rod is susceptible to wear from invasion of pollutants, and then ruins sealing ring in hydraulic cylinder. This work attempts to conduct a systematical investigation of Cu-DLC (Cu-doped Diamond-like Carbon) film to improve the seal performance. Failure process of hydraulic cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of piston rod in a multi-ion beam assisted system, and their structures and combined tribological performances were investigated. As a result, dust particles attached to the piston rod may enter the cylinder, and damage the sealing ring under the radial force. Cu grains prefer to orientate (111) crystal plane with increase of Cu content, and may induce drop of hardness and internal stress for the film. Friction coefficient of the film ranges from 0.04 to 0.15, and rise of IG/ID ratio from 1.4 to 2.3 in Raman data indicates that bond transition from sp3-C to sp2-C may lower the friction coefficient. Modification mechanism of Cu-DLC film for the seal performance may come from synergistic effects of (i) contact force and friction heat induce the film graphitization, (ii) Cu doping improves toughness of the film and acts as a solid lubricant, and (iii) transfer layer plays a role of self-lubrication.

The purpose of the study is to analyze the trade performance of Bangladesh during the COVID-19 pandemic. The study identifies the effects of private consumption demand shock and trade disruptions due to higher trade costs caused by the pandemic on the export and import of Bangladesh in different sectors and compares the analysis results with actual data. Based on the previous literature, this study assumes the shocks in different levels such as low, medium, and high level and identifies their effects on the trade in Bangladesh. The study applies the CGE model using GTAP to measure the effects of the shocks on trade and output and compares the actual trade with the CGE simulated results. The results of the study suggest that both demand shock and trade disruptions substantially affect the export, import, and domestic output of Bangladesh during the Covid-19 pandemic. It is also evident that the higher the level of shock, the higher the impact on trade and output. The actual export and import data cross-validate the CGE analysis results and provide mixed findings on the trade performance of various sectors of Bangladesh during the pandemic.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.

(1) Background: The purpose of this study was to investigate the relationship between IMO and burnout while assessing the contribution of job demands and resources on increasing internal orientation and worker well-being and, consequently, the levels of perceived performance; (2) Methods: Data were collected between April and December 2021 by completing an online questionnaire, developed in the Google Forms platform. The following descriptive statistics were analyzed: measures of central tendency (mean), dispersion (standard deviation), minimum value and maximum value. Next, Pearson's correlation coefficient was calculated to analyze the relationship between the variables under study.; (3) Results: The results showed the mediating effect of IMO between performance feedback and perceived performance, while burnout mediates the relationship between emotional and technology demands and perceived performance. (4) Conclusions: These conclusions demonstrate that constructive feedback might help a more efficient performance through better internal communication and the positive effects of technology demands could be the result of the interaction between personal and organizational resources.

Our research aims to address the urgent need for retrofitting measures to enhance the resilience of damaged coupling beams in real-life scenarios. We conducted a series of tests on scaled-down prototype coupling beams, carefully adhering to similarity theory requirements to ensure accurate representation. The test results showed that the chord rotation capacities of different specimens with the same diagonal bundle varied significantly due to the difference in the confinement levels. The specimens with lower level of confinement were found to have less displacement capacity. When the specimens were strengthened by wrapping with GFRP after damage, it was observed that the increase in confinement level significantly increased the chord rotation capacities of all specimens. In addition, in the tests before the strengthening, the elongation behavior of the specimens is observed until the damage development reaches approximately 2% chord rotation. With the in-crease in chord rotation, the elongation behavior of the specimens stops with increasing damage and then shortening behavior is observed. After retrofitting, it was observed that the axial elongation continued in a limited manner depending on the location and size of the concrete separated from the beam core in the case of collapse before strengthening, and then the beam showed a shortening behavior predominantly. After strengthening studies, our findings contribute valuable insights into the behavior and performance of damaged coupling beams, emphasizing the potential of urgent GFRP wrapping as a viable solution to enhance the seismic resilience of middle- and high-class buildings with structural walls after seismic events.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

Solar energy is a renewable and sustainable source of energy, and it has been used in addition of specified technologies, such as solar cooling. The demand for cooling continues to increase in line with environmental changes and a greater desire for human comfort. This study primarily aimed to analyze the performance of an evaporative cooling system powered by solar energy and assess the economic and environmental impact of this system. In this system, hot, dry incoming air is used to evaporate water, thus transforming part of its sensitive heat into latent heat without any variation in enthalpy or total heat. The outputted air then has a lower temperature and a greater humidity, thus providing a more comfortable, healthier environment for its users. To achieve this study’s objectives, numerical code was developed and implemented in MATLAB. The obtained results reveal that the efficiency of the evaporative cooler exceeds 90%, with maximum efficiency being reached at a high wet-bulb depression, while minimum efficiency was observed when the dry air has a high relative humidity and a low dry-bulb temperature.

The aim of this study was to develop and assess the reliability and validity of an innovative field test that measures lower limb explosive power in basketball players (i.e., alactic anaerobic capacity) for the dominant and non-dominant leg. The test examines the performance of vertical, horizontal, and combined movements while holding the ball – similar to penetration of the basket or layup. Such capabilities are required throughout basketball practice and games, combined with upper and lower body coordination. The study included 22 male basketball players, ages 16-18, members of an elite youth league team in Israel. To assess validity, the participants performed the test for each leg, followed by nine standardized tests that were developed for a range of ball games, including basketball. To assess reliability, the participants performed a retest of the unique test 72-hours later. Our findings indicate the validity and reliability of the proposed anaerobic alactic field test for basketball players, for the dominant and non-dominant leg. Moreover, strong correlations were seen between the novel test and the standardized tests, with a high correlation for horizontal explosive power (0.5<r<0.7), a very high correlation for vertical explosive power (0.7<r<0.9), and a nearly perfect correlation for the two combined (r>0.9). In conclusion, this unique field test for basketball players could assist coaches in developing and applying optimal training programs and game plans, for players individually, and for the team as a whole. As the test measures each leg separately, it could also offer an assessment tool following players’ injuries.

Burkina Faso is a sub-Saharan African country with a high poverty rate that has quadruplicated its population in the last half fifty years, that is, from 4.5 to 18 million inhabitants. Such demographic changes together with an intense migration process from rural areas to large cities, among other issues, are contributing to a rapid process of socio-cultural transformation. In this context, changes in both traditional and contemporary housing are analyzed and a complete ther-mo-hygrometric evaluation is carried out by processing significant data from on-site measure-ments to shed new light on the response of the said dwellings to the environmental and local cultural values. Results show that the introduction of land ownership linked to climate change and the increasing scarcity of natural resources are forcing native ethnic groups to modify their traditional ways of life, threatening their subsistence. Consequently, we can prove that the new building typologies are not in the least suitable for the climatic conditions nor the rich cultural heritage of Burkina Faso. This fact, negatively affects the possibility of revitalizing vernacular and environmentally-oriented solutions for the contemporary world and the necessary advance to-wards a more sustainable architecture.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

As a new distributed machine learning (ML) approach, federated learning (FL) shows the great potential to preserve data privacy by enabling distributed data owners to collaboratively build a global model without sharing their raw data. However, the heterogeneity in terms of data distribution and hardware configurations make it hard to select participants from the thousands of nodes. In this paper, we propose a multi-objective node selection approach to improve time-to-accuracy performance while resisting malicious nodes. We firstly design a deep reinforcement learning assisted FL framework. Then the problem of multi-objective node selection under this framework is formulated as a Markov decision process (MDP), which aims to reduce the training time and improve model accuracy simultaneously. Finally, a deep Q-netwok (DQN) based algorithm is proposed to efficiently solve the optimal set of participants for each iteration. Simulation results show that the proposed method not only significantly improves the accuracy and training speed of FL, but has stronger robustness to resist malicious nodes.

Unsmooth reversing is one of the most common faults in the four-way reversing valve of air conditioning system, and the airflow in the valve chamber and the shape of the slider of the reversing valve are the main factors in unsmooth reversing. In order to study the influence of the airflow in the chamber and the slider shape on the reversing process, the fluid flow in the valve chamber of a four-way reversing valve is obtained using computational fluid dynamics (CFD) simulations, and the influence of slider structure on slider thrust and resistance of the four-way reversing valve is analyzed. Four-way reversing valves with no-cutting, straight-cutting and arc-cutting sliders are employed to evaluate the reversing characteristics. A pressure measuring device for a four-way reversing valve chamber is designed, which is performed to test the chamber pressure of three different types of sliders of four-way reversing valves. The maximum error of experimental tests and simulations is within 5% of engineering tolerance, so as to verify the reliability of numerical simulation. The results indicate that the chamber pressure and resistance-thrust ratio with the cutting slider are reduced, which is beneficial to the reversing of the four-way reversing valve. Compared with the straight cutting structure, the arc cutting slider four-way reversing valve has a more stable reversing process and better comprehensive reversing performance. The results can provide a theoretical basis for engineers to improve the performance of four-way reversing valves.

As the echoes of ChatGPT's remarkable success continue to permeate the AI community, its formidable successor, GPT-4, has emerged, showing off a wealth of novel features. In this concise paper, we elucidate the capabilities of GPT-4 and conduct a comparative analysis with its predecessor, ChatGPT, offering insights into their relative strengths and advancements in the rapidly evolving field of generative AI. We also present a comprehensive summary of the major performance results reported by OpenAI on GPT-4 across various Natural Language Processing (NLP) tasks. We place great emphasis on the innovative advancements offered by GPT-4 in comparison to its predecessors. Our focus is on highlighting its remarkable performance while also mentioning its limitations. The purpose of this paper is to deliver a succinct understanding of the new features and performance benchmarks of GPT-4.

When sellers set the price for ex-ante unobservable and ex-post unenforceable quality, price signals credence quality. Hedge funds resemble incomplete long-term contracts for credence goods under buyer-determined auctions. I show that hedge funds' ability to solicit investments at higher management fees signals their capacity to generate higher net returns. This result is more pronounced during bust cycles and closer to financial hubs, i.e., when signaling quality is more valuable. The findings are relevant to understanding price and effort in the provision of credence goods like medical procedures and legal advice.

The effect of defatted Hermetia illucens meal (HIM) dietary inclusion on growth performance, stress indicators and gut histological traits of Sparus aurata was studied. For 131 days, 312 fish were fed with one basal diet, containing fish meal as animal protein source, and three diets containing 25%, 35% and 50% HIM as a partial replacement for fishmeal. On all fish (26 fish per tank, 3 replicate tanks per diet, 78 fish per diet) the growth performance were calculated. At the end of the trial, on a subsample of 72 specimens (6 fish per tank, 3 replicate tanks per diet, 18 fish per diet), stress parameters were determined on blood samples and gut histological tract investigated. Insect meal inclusion did not affect (p > 0.05) growth performance, blood parameters, length and width of villi and goblet cell count of the posterior gut tract while, those of the anterior gut tract while increased (p < 0.05). The histological examination of the intestinal sections showed in fish fed the HIM25 and HIM50 diets, more frequent and evident morphological changes; instead, there were no substantial differences between HIM0 and HIM35 groups. In conclusion, the HIM35 was the most tolerated formulation by fish.

Background: The duration of the vaccine's protective efficacy against SARS-CoV-2 is unknown. Evaluation of the clinical performance of available tests is required. Objectives: To evaluate the clinical performance of three immunoassays for the detection of IgG antibodies generated by mRNA vaccines against SARS-CoV-2. Methods: Two automated immunoassays (Euroimmun Anti-SARS-CoV-2 ELISA IgG and Abbott SARS-CoV-2 CLIA IgG) and one lateral flow immunoassay (LFIA Test Livzon IgG) were tested. 300 samples distributed in 3 groups were analyzed: 100 subjects over 18 years old and under 45 years old, 100 subjects between 45-65 years old and another 100 over 65 years old. collected before vaccination, at 21 days, 1, 2, 3 and 6 months post-vaccination. Sensitivity, specificity, positive predictive value, negative predictive value, positive likelihood ratio, negative likelihood ratio, and agreement (I. Kappa) were calculated for each serological test. Results: Maximum sensitivity for IgG was 98.7%, 98.1%, and 97.8% for the ELISA Euroimmun, CLIA Abbott, and Livzon LFIA assays and maximum specificity for IgG was 99.4%, 99.9%. % and 98.4% ELISA, CLIA and LFIA respectively at 3 months after vaccination with a decrease in antibody levels from the sixth month. The best agreement was observed between ELISA and CLIA 100%; (k = 1.00). The agreement between ELIA, CLIA and LIFIA was 99% (k = 0964) at the second and third month after vaccination. Seroconversion was faster and longer lasting in the younger age groups. Conclusion: Our study showed an equivalent and homogeneous clinical performance for IgG of three immunoassays after vaccination and that the LIFIA assay is the most cost-effective, reliable and accurate for routine use in population studies of seroconversion and seroprevalence.

The mental and emotional health of an athlete is crucial for their performance and well-being. Sports-related stress can significantly impair that mental health. Yoga of Immortals (YOI) is a unique combination of specific yogic postures, breathing exercises, sound therapy &amp; meditation, which has demonstrated benefit in improving measures of mental health. This study used the Sports Mind Inventory (SMI) to examine whether YOI can improve the resilience of athletes to sports-related stress. Participants were a diverse set of athletes based in Mauritius who routinely engage in a wide range of athletic activities. Participants were randomly assigned to receive four weeks of YOI or no intervention. Both groups completed the SMI questionarie at baseline and again after four weeks. The YOI intervention significantly increased the total mean SMI scores by 14%, indicating improved sports resilience and psychological health. No improvement was observed in the control group. This study demonstrates that YOI is a promising intervention in improving sports related stress.

The COVID-19 crisis has emphasized the importance of digital transformation of SMEs and has served as an accelerator. Digital transformation empowers SMEs to rethink the way they make decisions and apply technology in meaningful and sustainable ways. The purpose of this study is to explore the role of digital transformation, fostered by COVID-19, and its potential contribution to the sustainability of SMEs. This paper examines a new conceptual framework designed on resource-based theory perspectives by using a survey data of 246 SMEs in Latvia and employing mediation analysis. The main findings of the study are that digital orientation and digital capability have direct positive effects on digital transformation; higher levels of digital orientation and capability, mediated by digital transformation, lead to higher revenue; as well as a more sophisticated business model in the case of digital orientation. Even if we cannot confirm that higher digital capability, mediated by digital transformation, leads to a more sophisticated business model, we found statistically significant direct effects from digital capability to digital transformation and from digital transformation to business model. These findings can be useful for policymakers, managers and practitioners to clarify how digital orientation, digital capability intermediated through digital transformation affect sustainability of SMEs.

Based on the institutional theory and resource-based theory and the "institution-strategy-performance" research paradigm, this research explores the mechanism of institutional support on the innovation performance of new ventures, focusing on the mediating role of entrepreneurs and the moderating role of innovative resource acquisition. An empirical analysis based on 278 survey samples shows that: ① (formal/informal) institutional support positively affects the innovation performance of new ventures; ② entrepreneurial orientation plays an intermediary role between institutional support and innovation performance of new ventures; ③ innovation resource acquisition not only positively regulates the relationship between entrepreneurial orientation and innovation performance of new ventures, but also enhances the mediation of entrepreneurial orientation between institutional support and innovation performance. The conclusion shows that institutional support plays an important role in the innovation practice of new ventures, and can provide guidance for the innovation management practices of new ventures.

The study examines the relationship between corporate social responsibility (CSR) and the corporate life cycle (CLC) of the Chinese pharmaceutical listed companies for the duration of 2010 to 2018. The firm cash flow pattern is used as a proxy for the CLC. The study results indicate that the relationship between CSR and CLC is positive and linear in all the phases of the CLC including, the introduction, growth and maturity stage. Although the relationship is smaller and more significant at the maturity phase. The research further shows that investors incorporating social responsibilities values play a key role in the firm cash flow performance (CFP) across all the firm stages. Whilst, employees espousing social responsibility tenets can only improve CFP in the decline or shakeout stages. Likewise, embedding CSR into the customers group only improves CFP at the maturity stage. Applying the lag effects lead to the same study results. The finding for the bi-directional causality indicates that although CSR can positively influence CFP, CFP is ultimately more associated with the firm unobservable characteristics rather than performance attributed to CSR. On the whole, our study results point to positive causality between CSR and CFP across all the firm life stages and the CSR has a mediating effect on each life cycle.

Based on the resource-based theory, the current study examines the relationship between competitive strategies and strategic alliance performance. Furthermore, big data predictive analytics is treated as a boundary condition between competitive strategies and strategic alliance performance. Big data of predictive analytics in operations and industrial management has been a focal point in the current era. There has been little attention has about big data predictive analytics influences on competitive strategies and strategic alliance performance, especially in developing countries like Pakistan. A survey instrument was used to record the responses from 331 employees of the telecom sectors companies working in Pakistan. Study findings show that big competitive strategies have a positive and significant relationship with strategic alliances performance. It was also found that big data predictive analytics plays the role of moderator between competitive strategies and strategic alliance performance. The study add a new perspective and contribution to the literature on big data predictive analytics, strategic alliance performance, and competitive strategies in Pakistan's telecom sector companies. Further, the study results explain that big data analytics is just like the companies' lifeblood in the current era. The efficient and effective use of big data analytics, companies can boost their standards in a competitive environment.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

Introduction: The Elevation Training Mask 2.0 (ETM) has been introduced as a novel tool to allow for respiratory muscle training and altitude exposure during exercise that can improve performance and hematological markers in elite and well-trained athletes. Thus, the aim of the present study was to assess the effect of wearing ETM while training on erythropoietin (EPO), vascular endothelial growth factor (VEGF), peak oxygen consumption (VO2max), lactate, and 1000-m kayaking performance in elite Kayaking girls. Methods: Thirty elite Kayaking girls (14 to 18-year-old) were equally and randomly assigned into mask, no mask, and control groups. The mask and no-mask groups completed 8 weeks of repeated sprint training, while the control group performed their routine kayaking training programs. Pre- and post-training tests included EPO, VEGF, VO2max, lactate, and 1000-m kayaking performance. Results: 1000-m time trial significantly decreased for mask (p < 0.001) and control (p = 0.035) groups, and was significantly lower in mask group than control (p = 0.014) and no mask (p = 0.009) groups. EPO did not show any significant changes for all groups. VEGF was increased significantly for mask (p = 0.04) and no mask (p = 0.014) groups. Lactate was decreased significantly for mask group (p = 0.025). VO2max increased significantly for no mask group (p = 0.021). Conclusion: Wearing the ETM while participating in 8 weeks of repeated sprint training might improve specific blood markers and endurance performance, especially anaerobic pathways. Performing repeated sprint training while wearing ETM has the potential to enhance performance in Kayak racing.

There is an increasing pressure by community and customers forcing companies to insert environmental concerns in their practices. To help companies initiatives, the green bonds market was incepted. Our research question is how to select bonds in a growing billion-dollar market. This paper presents a multi-criteria decision analysis (MCDA) model to enable investors identify opportunities based not only in opinions, but grounded on objective facts. Analytic Hierarchy Process (AHP) and Complex Proportional Assessment (COPRAS) are two MCDA methods applied in this paper. Top-fifteen green bonds ranked by specialized media were assessed with the proposed MCDA model. Criteria included the Environmental Performance Index (EPI) proposed by Yale University, and common financial indicators as assets, risks (β), and dividends. The new AHP–COPRAS rank is compared with another published by specialized media.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

In order to alleviate the problems regarding conventional damping modeling techniques in nonlinear structural simulations, using concentrated plasticity formulation including rotational end springs with no damping plus middle elastic parts with modified assigned damping has recently been proposed. However, a proper selection for springs’ stiffness is a source of contention. In this paper, the effect of choosing different ratios for springs’ rotational stiffness to the elastic part of the elements on the seismic performance of RC moment frames was investigated. Incremental Dynamic Analysis (IDA) was performed and the derived responses were used for seismic performance assessment methodology. The results demonstrate that using flexible springs may lead to a greatly conservative estimation of collapse capacity, annual losses, and repair costs compared to a rigid one. Due to lack of experimental data, it is not possible to certainly assert the most appropriate ratio. However, such variation in the seismic performance of a building model with different stiffness modification necessitates more investigation on this modeling strategy.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

The influence of a high inclusion level of Chlorella vulgaris, individually and supplemented with two carbohydrase mixtures, in finishing pig diets was assessed on zootechnical performance, carcass characteristics, pork quality traits and nutritional value of pork fat. Forty crossbred entire male pigs, sons of Large White × Landrace sows crossed with Pietrain boars, with an initial live weight of 59.1 ± 5.69 kg were used in this trial. Swines were randomly assigned to one of four dietary treatments (n=10): cereal and soybean meal-based diet (control), control diet with 5% C. vulgaris (CV), CV diet supplemented with 0.005% Rovabio® Excel AP (CV+R) and CV diet supplemented with 0.01% of a four-CAZyme mixture (CV+M). Animals were slaughtered, after the finishing period, with a BW of 101 ± 1.9 kg. Growth performance, carcass characteristics and meat quality traits were not influenced (p > 0.05) by the incorporation of C. vulgaris in the diets. However, the inclusion of the microalga in finishing pig diets increased some lipid-soluble antioxidant pigments and n-3 PUFA, and decreased the n-6:n-3 ratio of fatty acids, thus ameliorating the nutritional value of pork fat. Moreover, the supplementation of diets with the carbohydrase mixtures did not change (p > 0.05) neither animal performance nor meat quality traits, indicating their inefficacy in the increase of digestive utilization of C. vulgaris by pigs under these experimental conditions. It is concluded that the use of C. vulgaris in finishing pig diets, at this high incorporation level, improves the nutritional value of pork fat without compromising pig performance.

The present study investigated the effect of different ambient temperature and relative humidity (RH) but equal temperature-humidity index (THI) on laying performance, egg quality, heterophil to lymphocyte ratio (H/L ratio), corticosterone (CORT) concentration in blood, yolk and albumen, and plasma biochemical parameters in laying hens. One hundred and twenty commercial hens (Hy-Line Brown) aged 60 weeks were allocated into 2 environmental chambers. Laying hens were subjected to either one of two thermal treatments, i.e., 26ºC and 70% RH (LH75) and 30ºC and 30% RH (HL75) for 28 days. Both thermal treatments had equal THI being 75. Neither LH75 nor HL75 affected (P > 0.05) laying performance including egg production, egg weight, egg mass, feed intake, and feed conversion ratio. Plasma biochemical parameters such as total cholesterol, high-density lipoprotein cholesterol, triglyceride, calcium, magnesium, and phosphorus was not altered (P > 0.05) by thermal treatments. As to the stress indicators, both environment regimes failed (P > 0.05) to affect blood H/L ratio and CORT levels in plasma, yolk and albumen although albumen CORT levels were elevated (P < 0.05) in LH75 vs. HL75 at days 3, 7, and 28. In conclusion, our study suggests that laying hens performed and responded equally when they were exposed to equal THI environment conditioned from either 26ºC and 70% RH or 30ºC and 30% RH. The results of this study will be served as a scientific basis for management decisions and handling under thermally challenging conditions.

The purpose of this study is to explore the effects of dual-task training, including cognitive tasks, on cognitive and bodily functioning and β-amyloid levels in Alzheimer's dementia patients. The subjects were 34 inpatients diagnosed with Alzheimer's dementia at a nursing hospital located in Gyeongsansi, South Korea. The patients were randomly divided into a dual-task group (n = 16) and a single-task group (n = 18). The dual-task group performed cognitive tasks at the same time as exercising tasks, while the single-task group performed only exercise tasks. Each group was trained for 30 minutes three times a week for eight weeks. The Mini-Mental State Examination was used to measure the patients’ cognitive function. Static and dynamic balance were measured to evaluate bodily functioning. Static balance was measured using Biorescue, while dynamic balance was measured using the Berg Balance Scale. Blood analysis was performed to measure levels of β-amyloid, which is known to cause Alzheimer's dementia. Both groups exhibited statistically significant improvements in gait function after the training (p < .05). The dual-task group exhibited statistically significant differences in cognitive function, static and dynamic balance function, and β-amyloid levels after training (p < .05). A significant difference was observed between the two groups (p < .05). Dual-task activities were found to be effective in improving cognitive and bodily functioning and reducing β-amyloid levels in Alzheimer's dementia patients. Therefore, dual-task training is thought to be an effective method of treating and preventing Alzheimer's dementia.

2S-hesperidin is a flavanone (flavonoid) found in high concentrations in citrus fruits. It has an antioxidant and anti-inflammatory effect, improving performance in animals. This study investigated the effects of chronic intake of an orange extract (2S-hesperidin) or placebo on aerobic-anaerobic and metabolic performance markers in amateur cyclists. A double-blind, randomized, placebo-controlled trial was carried out between late September and December 2018. Forty amateur cyclists were randomized into two groups: one taking 500mg/day 2S-hesperidin and other taking 500 mg/day placebo (microcellulose) for 8 weeks. All participants completed the study. Performance and metabolic aerobic-anaerobic markers were measured using incremental and rectangular tests by indirect calorimetry. The anaerobic power was determined using Wingate tests. After 8 weeks supplementation, there was a significant increase in the incremental test in estimated functional threshold power (FTP) (3.23%; p≤0.05) and maximum power (2.68%; p≤0.05) with 2S-Hesperdin compared to placebo. In the rectangular test, there was a significant decrease in VO₂ (-8.26%; p≤0.01) and VO₂R (-8.88%; p≤0.01) at VT2 in placebo; however, there were no significant differences between groups. In the Wingate test, there was a significant increase (p≤0.05) in peak and relative power in both groups, but without significant differences between groups. Supplementation with an orange extract (2S-hesperdin) 500mg/day improves estimated FTP and maximum power performance in amateur cyclists.

In an innovation driven business environment, cross-border access to resources is important for companies to improve innovation capabilities and development performance. Based on the previous research, it shows that there are barriers to cross domain communication among alliance firms because of the restriction of multidimensional ties and dyads. Simmelian ties, as a form of alliance network with ternary connections, it effectively restrained opportunism and self-interest in the cooperation process and take a crucial role to evaluate innovation related performance in corporation. Based on the theory of Simmelian, this paper builds a theoretical framework and proposes corresponding research hypotheses between Simmelian ties and enterprise innovation performance. After designing questionnaires, collecting data and conducting empirical analysis to test theoretical models and hypotheses. Results have shown that: (1) Simmelian ties generally have a positive impact on enterprise innovation performance. (2) Knowledge capturing and knowledge integration play a partial intermediary role between Simmelian ties and enterprise innovation performance, and the mediating chain formed by the two variables plays a serial mediating role in the effect. (3) Network routines significantly positively moderates the relationship between Simmelian ties and knowledge capturing. And also, the positive relationship between Simmelian ties and enterprise innovation performance is also actively moderated by network routines. The conclusion of this study is meaningful for companies to establish of Simmelian ties, improve knowledge management capabilities and further promote enterprise innovation performance.

Education plays an essential role in the acquisition of knowledge and skills. School is the place where children’ attitudes, interests, and habits are developed. More involved and supportive a parent is towards their adolescent the higher self-esteem they will gain allowing the adolescent to feel confident and focused during school. Parents therefore enroll their children in schools that can give them expected quality of lives. The main core objective for this study was to determine the parental influence on students’ academic performance - A case study of Debre Berhan General Secondary School. A total of 118 students were included in the present study using simple random sampling technique from the total students (2367). Cross-sectional design was appropriate for this study. Primary source of data was employed collected from students. Descriptive and inferential statistics were applied. For statistical analysis SPSS 20 was used at 5% level of significance. Descriptive statistics results indicate that the average mark of students was with minimum and maximum value of 47 and 94 respectively. Multiple regression models showed that Income level, Rate of money given to satisfy basic and educational materials, Parent’s occupation, Family size, Parent’s educational level, and Parent’s way of giving motivation were found to be a significant effect on academic performance of students at 5% level of significance at study area. However, sex of students, age of students and grade level of students were not found to be significant effect to academic performance at study area. Overall model is statistically significance for the data. All the assumption of regression analysis was satisfied. Normality, Constant variance, absence of multicolinearity, linearity and absence of autocorrelation were satisfied due to formal tests and diagnostic plots. Study recommended the need for programs related to improvement of mother and father education for caring child in appropriate success of their education and also parents should allocate time to visit schools and establish good relationship and discussion about their children’s academic progress in according to way of motivation to learn actively in school.

The present study was conducted to evaluate encapsulated essential oils as an alternative anticoccidial in coccidiosis vaccine challenged broiler chickens. A total of 600 day-old male broiler chicks were provided with no-added corn-soybean meal-based control diet or diets that contained either salinomycin or EO at 60 and 120 mg per kg of diet. On day 21, half of the control groups were orally challenged with a coccidiosis vaccine at 25 times higher than the recommended vaccine dose. During 22 to 28 days (i.e., one-week post coccidiosis vaccine challenge), the challenged chickens had decrease (P < 0.05) in body weight gain and feed intake but increase in feed conversion ratio compared with the non-challenged, naïve control chickens. However, dietary EO significantly counteracted (P < 0.05) coccidiosis vaccine-induced depression in body weight gain and feed intake. Increasing dietary EO linearly decreased (P < 0.05) the concentrations of the volatile fatty acids. Dietary SAL and EO affected gut morphology in chickens at 20 days posthatch. Increasing dietary EO linearly (P = 0.073) increased serum catalase activity. Collectively, our study shows that dietary EO increased coccidiosis vaccine-induced growth depression and altered gut physiology in broiler chickens.

The energy yield of the Vehicle-integrated photovoltaic (VIPV) differs from that of the standard photovoltaics (PV). It is mainly by the difference of the solar irradiance onto the car-roof and car-bodies as well as its curved-shape. Both meaningful and practical modeling and measurement of the solar irradiance for VIPV are needed to be newly established, not the extension of the current technologies. The solar irradiance was modeled by a random distribution of the shading objects and car-orientation with the correction of the curved surface of the PV modules. The measurement of the solar irradiance onto the car-roof and car-body was done using five pyranometers in five local axes on the car for one year. The measured dynamic solar irradiance onto the car-body and car-roof was used for validation of the solar irradiance model in the car.

The aim of the research was a comprehensive evaluation of concrete using the EIPI method. In the evaluation the compressive strength of concrete and its durability properties represented by sorptivity and air permeability were taken into account. Since copper slag waste with increased natural radioactivity was used in the assessed concrete, additional evaluation was carried out taking into account the influence of natural radioactivity within the performance index. Also the reference concrete, which was made without the use of copper slag waste, was evaluated for comparative purposes. In order to make the evaluation as comprehensive as possible, the concrete made with the use of three types of cement was subjected to the assessment: CEM I, CEM II and CEM III. The results show that in both approaches the best result was achieved by concrete with CEM III cement. If natural radioactivity is not taken into account in the evaluation, the best result is obtained by concrete made with copper slag waste, and if radioactivity is considered, the best result is obtained with concrete without addition of the waste. It follows from the above that although natural radioactivity has a significant impact on the EIPI evaluation result, the decisive factor is still the type of cement.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

The aim of this study was to identify gender differences in technical-tactical behaviour in football. To this end 68 matches of the first division of the Spanish men’s and women´s league, corresponding to 2016/17 season were analyzed. A comparison of medians was carried out using the Mann-Whitney U-test were conducted as post hoc test and a grouping of the variables through the clustering bootstrapping technique in both groups. We have detected statistically significant differences regarding all accurate passes, in favour of men, as well as a greater number of yellow cards. In female football, a greater number of picking up free balls, interceptions, lost balls, recoveries, challenges and attacks, both positional and counterattacks, are produced. The clustering analysis also allowed that in male football, the circumstance of receiving a red card is closely related to the number of goals conceded and most of the shots on goal are achieved by positional attacks. In women's football, ball possession on own half is closely related to the number of losses. These results could be useful for gender-specific training information for optimal preparation. However, more research is warranted to establish the main gender differences and characterize women's football.

Solar radiation is closely related to the energy buildings consume for cooling, heating, and lighting purposes. Glazing is the only material of the building envelope that transmits solar radiation and needs to be appropriately designed to reduce energy cㅈonsumption. Currently, smart glass technology is being actively investigated and developed for effective solar radiation control. Among the various types of smart glass, electrochromic glazing is one of the most promising technologies, as it can adjust transmittance on its own, has a wider transmittance range in both the clear and darkened states, and consumes less electricity. Considering the importance of solar radiation adjustment in electrochromic glazing technology, this study attempted to develop an optimal control method for electrochromic glazing. Toward this goal, the solar radiation incident on vertical surfaces and outdoor temperature conditions were controlled in three regions with different climatic characteristics, and the annual cooling, heating, and lighting loads, discomfort glare, and interior illumination were analyzed. This approach enabled the optimal conditions with respect to visual comfort to be determined. Subsequently, the EDPI (Energy and daylight performance index) was used to optimize control conditions for each region, thereby producing integrated evaluations from results with different units and properties. The proposed control method will be utilized to develop a control algorithm and a control system to reduce building energy consumption.

Aortic rupture is known as one of the potential causes of sudden cardiac death in athletes. Nevertheless, adaptation strategies for aortic root dilation in athletes vary. The purpose of this study was to investigate aortic root adaptation to physical workload and to determine if aortic root’s and left ventricle sizes are contingent upon the physical workload. Echocardiography was applied to 151 subjects to measure the aortic root at aortic valve annulus (AA) and at sinus of Valsalva (VS). 122 were athletes (41 females and 81 males) and 29 were non-athletes (14 females and 15 males). Of the 41 female athletes, 32 were endurance athletes, and 9 strength athletes. From 81 male athletes, 56 were endurance athletes, and 25 were strength athletes. AA and VS mean values for the body surface area were presented as rAA and rVS. Left ventricle (LV) meaures incuded LV end-diastolic diameter (LVEDD), interventricular septum thickness in diastole (IVSTd), LV posterior wall thickness in diastole (LVPWTd), LV mass (LVM), LV mass index, LV end-diastolic diameter index (LVEDDI). Results indicated that VS was higher in female athletes (28.9±2.36mm) than in non-athletes (27.19±2.87mm, p=0.03). On the other hand, rAA was higher in strength athletes (12.19±1.48mm/m2) than in endurance athletes (11.12±0.99mm/m2, p=0.04). Additionally, rVS and rAA were higher in female strength athletes (17.19±1.78mm/m2, 12.19±1.48mm/m2) than female basketball players (15.49±1.08mm/m2, p=0.03, 10.75±1.06 mm/m2, p=0.02). Statistically significant positive moderate correlations were found between VS and LVEDD, LVM, IVSTd, LVPWTd, rVS and LVEDDI parameters in all athletes. The diameter of Valsalva sinus was greater in female athletes compared to non-athletes. The rAA mean value for body surface area was greater in female athletes practising strength sports as compared to their counterparts who were practising endurance sports. The diameter of the aortic root at sinuses positively correlated with the LV size in all athletes. Trial was registered at ClinicalTrials.gov Identifier: NCT03656861, September 3, 2018 (retrospectively registered).

A car-roof photovoltaic has an enormous potential to change our society. With this technology, 70% of the personal car can run by the solar energy collected by the solar panel on its car-roof. Unfortunately, it is not a simple extension of the conventional photovoltaic technology. This paper list what we need to do for realizing the future that majority of the personal cars run by renewable solar energy, after clarification of the difference from the conventional photovoltaic technology. In addition to the technological development, the standardization of this innovative technology will be important, and the list was made highlighting the standardization.