Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

The key objective of the experiment was to show the environmental based of copper nanoparticles which counters the growth of bacterial pathogens such as Pseudomonas aeruginosa, and Staphylococcus aureus. To begin with the experiments, root extract of Asparagus racemosus was used to synthesise Copper nanoparticles. To confirm the formation of Cu-NPs, it was subjected to characterization such as Ultra Violet analysis, X-ray Diffraction method, Fourier Transform Infrared Spectroscopy and Scanning electron microscope images. Later the antibacterial activity of Cu-NPs was studied by incorporating it into two bacterial pathogens (Pseudomonas aeruginosa and Staphylococcus aureus). The outcome displayed a satisfactory antibacterial activity against the bacterial pathogens by the biosynthesized copper nanoparticles. To boost up the enzyme inhibition property of the Cu NPs, Antioxidant and Antidiabetic assay were also performed. The biosynthesised Cu NPs displayed a satisfied result in Antifouling function. The result was used assessed with green algae bloom water.

Femtosecond laser-induced fluorescence (FLIF) and femtosecond laser-induced optical breakdown spectroscopy (FIBS) are important tools for remote diagnostics of atmospheric aerosols using LiDAR techniques. They are based on light emission excitation in disperse medium via the multiphoton nonlinear processes in aerosol particles induced by high-power optical pulses. To date, the main challenge restraining the large-scale application of the FLIF and FIBS in atmospheric studies is the lack of valued theory of the stimulated light emission in liquid microparticles with sufficiently broad range of sizes. In this paper, we fill this gap and present the theoretical model of dye water droplets emission under high-intense laser exposure that adequately simulates the processes of multiphoton excited fluorescence and optical breakdown plasma emission in microparticles and gives quantitative estimates of the angular and power characteristics of the nonlinear emission. The model is based on the numerical solution to the inhomogeneous Helmholtz equations for the stimulating (primary) and nonlinear (secondary) waves provided by the random nature of molecule emission in particles. We show that droplet fluorescence stimulated by the multiphoton absorption generally becomes more intensive with increasing particle size. Moreover, far-field plasma emission from liquid particles demonstrates larger angular diversity when changing droplet radius in comparison with the multiphoton excited fluorescence, which is mainly due to the excitation of the internal optical field resonances in spherical particles.

Background: Skin and soft tissue infections (SSTI) are common presentations to the emergency department. However, this is less common after contact with contaminated water, both salt or fresh. This review presents the diagnosis and the management of water-related soft tissue sepsis in this vulnerable and difficult to treat subgroup of necrotizing soft tissue sepsis. Methods: A summative literature overview regarding bacterial and fungal SSTI after contact with contaminated water, with practical diagnostic and management aspects addressed. Results: The literature indicates that these remain difficult to treat wounds and organisms. An approach using appropriate diagnostic tools with both medical and surgical management strategies is provided. Conclusion: SSTI due to water contamination of wounds involve unusual organisms with unusual resistance patterns and require a nuanced and directed diagnostic approach with adaptation of the normal antibiotic or antifungal selection to achieve cure, along with aggressive debridement and wound care.

The Roman villa of Pisões (Beja, Portugal), was part of the Lusitanian colony of Pax Iulia. This place stands out for the predominance of the water element in several structures of the villa, highlighting the balneum and the large natatio, one of the largest known in Roman Hispania. The records of the initial excavations that took place since 1967 do not allow the establishment of clear functionalities of the villa. The University of Évora, owner of the site, conceived an action plan for the requalification and enhancement of the archaeological site. One of the tasks aims to investigate using Applied Geophysics. This work analyses the landscape directly related to the villa, given that it is in the flooded area of a river, with a Roman containment dam. It is uncertain whether the water supply comes from this structure or other nearby springs. The use of ground-penetrating radar, combined with unnamed aerial vehicles, all integrated in a geographic information system, allows us to know the location of underground water connections and create a topographic model with high resolution. Considering all the information, we propose a model for the water transport inside the villa and estimate the location of the water supply.

Steam Generator Level Control System (SGLCS) is one of the key instrumentations and control subsystems to ensure the safe operation of nuclear power plants. It is highly recommended to perform reliability analysis for SGLCS for making better maintenance strategy. SGLCS is a digital control system with complex redundant configuration and failure\self-diagnosis\repair action, traditional fault tree is not applicable due to its static property, Markov model is not a good choice too because of heavy burden of creating state transition graph for even medium-size system. Boolean Logic Driven Markov Process (BDMP) can describe complex failure-repair state transition via ‘trigger link’ and three kinds of leaf nodes, as well as keep compact and easy-read struct like fault tree. So BDMP is adopted to analysis reliability of SGLCS. Graphical BDMP modeling environment KB3 and Monte Carlo simulator YAMS is used for BDMP modeling and quantitative analysis respectively, and unavailability of SGLCS is obtained. The contribution of three parts of SGLCS to the unavailability of the system is also evaluated, and it is found that the water supply flow control part contributes the most to the failure of SGLCS.

Currently, the design and construction of embankments of roads, railroads and hydraulic structures are based on regulatory documents developed 25-30 years ago. For the construction of granite massifs it is necessary to use sandy soils, the distribution of which in the Arctic zone of Siberia in the areas of construction is not more than 1.5%. In this case, the range of transport of sand in the alluvial area is 35 kilometers, in the rest of the area - an average of 60 kilometers. Large volumes of soil massifs require large amounts of transportation units, fuel consumption and are accompanied by large emissions of hydrocarbons into the atmosphere. Over the past 15 years, the authors have developed designs and technologies that significantly reduce the energy consumption during the construction of soil embankments. Combined structures are cages made of geosynthetic materials filled with unsuitable melted and frozen overmoistened clay and peaty soils. This allowed the use of soils within the construction sites and thereby reduce the range of transportation from 0.2 to 2.0 kilometers. As an example, when reducing the range of transportation from 25 km to 1 km, the energy consumption is reduced by a factor of 21. The use of geosynthetics made it possible to set the initial parameters of the water-heat regime control process, which increased the life cycle of the embankment from 2 to 5 times in comparison with traditional soil massifs and reduced the consumption of energy for repair and maintenance of linear transport structures. This article gives a theoretical substantiation of water-heat regime management, based on which new designs and technologies have been proposed and tested in Siberia in 2008-2013. The results of the tests confirm the theoretical research. Thus, the use of combined constructions of geosynthetics and inapplicable soils not only reduces the distance of transportation, but also reduces the volume of earthworks. It reduces the consumption of energy by 1.5-2 times.

The article is devoted to the topical problem of estimating water content in water-oil mixtures and porous media they saturate, according to low-field NMR relaxometry and dielectric spectroscopy. The aim of the research is to theoretically substantiate and experimentally validate the capability of joint interpretation of data from these methods to acquire information on the filtration-volumetric properties of drill cuttings, relaxation characteristics of oil-containing fluids, water/oil ratio in water-oil mixtures and saturated with them drill cuttings in order to control the composition of liquids produced from boreholes. The studies were carried out on samples of cuttings and oils taken from fields in the northern and Arctic regions of the West Siberian oil-and-gas province. Based on the experimental data obtained, we evaluated the water content in the water-oil mixtures, determined the main NMR parameters of the mixtures in terms of properties of the constituent oils, and specified the parameters and shapes of NMR and complex dielectric permittivity spectra. The NMR method was found to be effective in examining high-viscosity and medium-viscosity oils, while the dielectric spectroscopy method – in the study of light oils; their integration allows obtaining reliable data for all the samples under study. We also showed how the shapes of NMR and complex dielectric permittivity spectra depend on the rheological properties of oil belonging to the mixture.

The Mediterranean is one of the regions of the world where human-induced climate warming is expected to have large impacts on water and environmental resources. To predict shifts in the current climate system, more regional climate records, including seasonal-to-century scale variability spanning longer than the instrumental periods, are needed. To help fill this gap, we provide a reconstruction of autumn precipitation variations for the Central Pyrenees range since 1500 Common Era (CE) using the varved sediments of Lake Montcortès. To assess the suitability of the calcite sublayer width of the sediments of this lake as a proxy for precipitation anomalies, we performed an analysis and smoothing of the temporal structure of the width series, calibration of the new series with the available instrumental climate records, calculation of a transfer function and testing and comparison of the reconstructed series against available empirical data.The prediction model was statistically robust and showed that the climatic signal was captured in the calcite sublayers. The reconstruction provides the first estimations of regional autumn precipitation shifts in the Central Pyrenees at annual resolution, since 1500 CE. Pronounced interdecadal shifts in precipitation were noticeable; no increasing nor decreasing linear trends or periods of extreme precipitation events were identified. The reconstructed precipitation anomalies suggest a decrease in rainfall during the coldest phase within the coldest period of the Little Ice Age and also during the 20^th century, probably associated to current Global Warming. Correlations between autumn precipitation and the North Atlantic Oscillation, Western Mediterranean Oscillation and Southern Oscillation indices were weak to moderate. A potential relationship with the Atlantic Multidecadal Oscillation pattern is suggested. The reconstructed autumn precipitation trends are coherent with other palaeohydrological reconstructions in similar Mediterranean settings, and consistent at a regional level.

The water quality of the river is becoming deteriorated due to human interference. It is essential to understand the relationship between human activities and land-use types to assess the water quality of a region. GIS has the latest tool for analyzing the spatial correlation. Land use land cover and change detection is the best illustration to show the human interactions on land features. The study assessed water quality index of upper Ganga River near Haridwar, Uttarakhand and spatially correlated them with changing land use to reach a logical conclusion. At the upper course of Ganga along 78 Km long from Kaudiyala to Bhogpur, water samples were collected from five stations. For water quality index the physicochemical parameters like pH, EC, DO, TDS, CaCO3-, CaCO3, Cl¯, Ca++, Mg++, Na+, K+, F-, Fe2+ were considered. The result of the spatial analysis was evaluated through error estimation and spatial correlation. The root mean square error between spatial land use and water quality index of selected sampling sites was estimated as 0.1443. The spatial correlation between land-use change and site-wise differences in water quality index has also shown a high positive correlation with R² = 0.8455. The degree of positive correlation and root mean square error has strongly indicated that the water quality of the river at the upper course of Ganga is highly impacted through human activities.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

Bioethanol has many environmental and practical benefits as a transportation fuel. It is one of the best alternatives to replace fossil fuels due to its liquid nature which is similar to petrol and diesel fuels traditionally used in transportation. In addition, bioethanol production technology has the capacity for negative carbon emissions which is vital for solving the current global warming dilemma. However, conventional bioethanol production takes place based on an inland site and relies on freshwater and edible crops (or land suitable for edible crop production) for production, which has led to the food vs fuel debate. Establishing a coastal marine biorefinery (CMB) system for bioethanol production that is based on coastal sites and relies on marine resources (seawater, marine biomass and marine yeast) could be the ultimate solution. In this paper, we aim to evaluate the environmental impact of using seawater for bioethanol production at coastal locations as a step towards the evaluation of a CMB system. Hence, a life cycle assessment for bioethanol production was conducted using the proposed scenario named Coastal-Seawater and compared to the conventional scenario, named Inland-Freshwater (IF). The impact of each scenario in relation to climate change, water depletion, land use and fossil depletion was studied for comparison. The coastal-seawater scenario demonstrated an improvement upon the conventional scenario in all the selected impact categories. In particular, the use of seawater in the process had a significant effect on water depletion showing an impact reduction of 31.2%. Furthermore, reductions are demonstrated in natural land transformation, climate change and fossil depletion of 5.5%, 3.5% and 4.2% respectively. This indicates the positive impact of using seawater and coastal locations for bioethanol production and encourages research to investigate the CMB system.

Controlled drainage (CD) is an important agricultural measure for maintaining soil moisture and nutrients, controlling groundwater level, and increasing crop yield. In arid regions, CD can be used to improve the water supply in agriculture and reduce environmental pollution. In this study, we investigated the effect of CD, including a drainage depth of 40 cm (CWT1) and 70 cm (CWT2) during the plant growth period, free drainage (FD), and open ditch drainage (OD) on the migration of water, nutrients, and salts in the soil; the dynamics of groundwater level; the loss of soil nitrogen; and the growth of oilseed sunflower plants. Compared with FD, CD increased the water and nutrient content in the soil, reduced nitrogen loss, and enhanced the ability of the soil to continuously supply nitrogen to the oilseed sunflower plants, which benefited plant growth at later growth stages and reduced environmental pollution. During the period between irrigation at the budding stage and harvest stage, the average soil water content in the 0–20 cm soil layer in CWT1 increased by 3.67%, 4.78%, and 0.55%, respectively, compared with that in CWT2, FD, and OD. The soil mineral content in CWT1 was 25.17%, 35.05%, and 17.78% higher than that in CWT2, FD, and OD, respectively, indicating that higher soil salinity occurred at the later stage of plant growth in CWT1, which actually had little effect on the plants due to their enhanced salt tolerance and increased need for water and nutrients at that stage. In addition, CD delayed the decline in groundwater level, which allowed the plants to use groundwater at later growth stages, and as a result the yield and water use efficiency were improved. CWT1 significantly increased oilseed sunflower yield by 4.52–11.14% and increased water use efficiency by 1.16–10.8%. Moreover, CWT1 also increased the survival rate of the oilseed sunflower plants by 2.62–2.92%, and the plants demonstrated good growth. Therefore, under CD conditions, plants used soil water and nitrogen more efficiently and, as a result, their productivity was increased, and the water quality was improved.

As for most Mediterranean countries, groundwater is the main resource for irrigation and drinking supply in most parts of Syria, however this resource suffers from mismanagement. In the study area (Northeast of Mt. Hermon), the lack of information makes water management in this area extremely difficult. Assessing groundwater pollution risk is the most essential issue for water resources management, especially in the regions where complex interaction between climate, geology, geomorphology, hydrogeology, water scarcity and water resource mismanagement exist. This complexity leads to significant complication in determining pollution risk of studied system. In the present work, we adopted an Integrative Approach to assess groundwater pollution risk in the study area. This methodology is based on the analysis of hydrogeological characteristic of aquifer system and the available information about socio-economic context and physio-chemical groundwater condition that might affect this system. This approach allowed us to delineate the groundwater pollution risk map based on the analysis of concerning parameters/ indicators. The degree of risk was assessed based as the sum and average of rating of these parameters and indicators for each subarea. Typically, very high pollution risk index was identified over the Quaternary/Neogene horizon, i.e shallow and unconfined aquifer and in the lower part of Jurassic aquifer. In these two parts, the majority of anthropogenic activities are concentrated. Low pollution risk index was found for the outcropping of low permeable Quaternary basalt at the Southern part of the study area. A moderate pollution index was identified for the low/moderate permeability of silt, clay and marly limestone rich horizons of the major part of Neogene aquifer outside of the intersected zones with Quaternary aquifer and for the Paleogene formations. The spatial analysis shows that about 50% of the study area is characterized as being at very high and high pollution risk index. Hence, the overall natural protective capacity of this area is still poor. This study demonstrates the flexibility of the proposed approach to assess groundwater pollution risk in local complex aquifer system characterized by lack of information and data in order to reduce the risk of future groundwater pollution.

One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.

Specific aquaporins (AQP), called peroxyporins, play a relevant role in controlling H2O2 permeability and ensure reactive oxygen species wasting during oxidative stress. Another target involved in oxidative stress is the Sigma1 Receptor (S1R), since its activation is triggered by oxidative or endoplasmic reticulum stress. Herein we evaluated the effect of S1R modulators on AQP-dependent water permeability in the presence and in the absence of oxidative stress. Applying stopped-flow light scattering and fluorescent probe methods, water and hydrogen peroxide permeability in Hela cells have been studied. Results evidenced that S1R agonists can restore water permeability in heat-stressed cells and the co-administration with a S1R antagonist totally counteracted the ability to restore the water permeability. All compounds except one were able to counteract the oxidative stress of HeLa cells specifically knocked down for S1R. Taken together, our results support the hypothesis that the investigated compounds act as dual aquaporin and Sigma1 receptor (DAS) modulators. The finding that small molecules can modulate both AQP and S1R opens a new direction toward the identification of innovative drugs able to regulate cell survival during oxidative stress in pathologic conditions, like cancer and degenerative diseases.

Highly-resolved data on water balance components (like runoff or storage) are crucial to improve water management, e.g., in drought or flood situations. Because regional observations of these components cannot be acquired adequately, applying water balance models is a feasible solution. We developed an innovative approach using the physically-based lumped-parameter water balance model BROOK90 (R version) integrated into a sensor network platform to derive daily water budget components for catchments in the Free State of Saxony. The model is not calibrated but rather uses available information on soil, land use and precipitation only. We applied the hydro response units (HRUs) approach for 6175 small and medium-sized catchments. For the evaluation, model output was cross-evaluated in ten selected head catchments in a low mountain range in Saxony. The mean values of Kling-Gupta efficiency (KGE) for the period 2005-2019 to these catchments are 0.63 and 0.75 for daily and monthly discharge simulations, respectively. The simulated evapotranspiration and soil wetness are in good agreement with the SMAP_L4_GPH product in April 2015-2018. The study can be enhanced by using different data platforms as well as available information on study sites.

Soil water loss by evaporation influences the sodium adsorption ratio (SAR) of irrigation drainage water. Evaporation concentrates sodium and magnesium but calcite precipitation has a more complicated effect on soluble calcium and alkalinity. Here we propose a revised sodicity hazard assessment that quantifies the impact of evaporative water loss and calcite precipitation on drainage water SAR. This paper shows sodicity hazard is determined by the initial composition of irrigation water as originally suggested by previous researchers, and provide a simple, accurate way to identify the potential sodicity hazard of any irrigation water. In particular, the initial equivalent concentration of alkalinity and calcium determine the salinization pathway followed during evaporation. If the irrigation water alkalinity exceeds soluble calcium expressed as equivalent concentrations, drainage water SAR approaches an upper limit determined by the initial relative concentration of sodium and magnesium. If irrigation water alkalinity is less than soluble calcium, drainage water SAR approaches a lower limit determined by the initial calcium, magnesium and sodium. In both cases the SAR is scaled by the square root of the concentration factor √Fc quantifying soil water loss. To assess the impact of evaporation and calcite precipitation on the SAR and test the accuracy of the new sodicity hazard assessment, we evaluated data from previously published lysimeter studies. We plotted water composition boundaries for each source water, comparing these boundaries to the drainage water composition recorded in the lysimeter studies. As salinity increased by evaporation, each drainage water followed a distinct salinization path.

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

In this article, we report the generation of alternating current by application of constant and ramping DC voltages across oil-water interfaces. The work reported here can be broadly divided into two parts depending on the shapes of oil-water interfaces i.e. flattened and curved. In the first part, an alternating current of ~100 nA (amplitude)was generated by applying a constant DC voltage of -3V& above across a free standing and flattened oil-water interface.In another part, an alternating current of ~150 nA (amplitude) was generated by applying a ramping up DC voltage starting from -5V to 5V, then again ramping back down to -5V for the free standing and curved interface. The suggested qualitative mechanism that engenders such a phenomenon includes the oil-water interface acting like a membrane. This membrane oscillates due to the electrophoretic movement of ions present in aqueous phase by application of a DC voltage across the interface.This electrophoretic movement of ions across oil-water interfaces causes the Faraday instabilities leading to oscillations of the said interface.This method could also be used to study the stress levels in the interfacial films between two immiscible liquids. It explores more-than-Moore’s paradigm by finding a substitute to a conventional alternator/inverter that generates alternating current upon applying DC voltage input. This work would be of substantial interest to researchers exploring alternatives to conventional AC generators that can be used in liquid environments and in the design of novel integrated circuits that could be used for unconventional computing applications.

Easy to use satellite-based water quality visualizations are needed for monitoring and understanding coastal and inland waters, but to date, no publicly accessible real-time global visualization system was in place. Here we introduce the Ulyssys Water Quality Viewer (UWQV), a Sentinel Hub EO Browser Custom script designed for qualitative views of aquatic chlorophyll and suspended sediment concentrations. The viewer avoids unmixing of the chlorophyll and suspended sediment spectral signal by visualizing these parameters together, with high concentrations of suspended sediment obscuring chlorophyll if present. Cloud masking uses the Hollstein and Braaten algorithms (existing EO Browser custom script code), additionally water surfaces are masked using the Normalized Differential Water Index. Chlorophyll is estimated using reflectance line height-based indicators such as fluorescence line height and maximum chlorophyll index. Suspended sediment is visualized based on single-band reflectances at 620 or 700 nm. Data sources are Sentinel-2 and Sentinel-3 images, allowing either 20 m spatial resolution or up to daily imaging. This visualization system is easy to operate and interpret, and combined with the data service capacity of the Sentinel Hub, it is expected that UWQV will contribute to monitoring of remote water bodies and to our overall understanding of physical limnology and aquatic ecology.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

The exposure of people to opportunistic premise plumbing pathogens (OPPPs) such as Legionella, Mycobacterium and Pseudomonas in aerosolised water has been linked to opportunistic infections. Water mist systems (WMS) that are used to cool public places by flash evaporation of tiny water aerosols are gaining prominence in hot climatic regions of Australia. Their potential to be colonised by OPPPs has not been adequately studied. The public health impact of OPPPs is significant, as Legionella caused 63% of waterborne disease case hospitalisations in the United States associated with drinking water systems during 2013–2014, and the incidence of Mycobacterium avium over the same period was 647 cases per 100,000. As WMS are part of premise plumbing, they have structural characteristics that can promote biofilm formation, as well as the presence of free-living amoebae (FLA), low residual disinfection levels, elevated water temperatures and oligotrophic conditions, all of which can promote OPPP inhabitancy. This review highlights the potential public health risks of using WMS as a cooling intervention in public places and advocates for their regulation in places of public assembly and entertainment.

Organic farming has positive, impact on environment, soil health, and healthy food quality. Worldwide demand for organic foods is increasing by leaps and bounds in recent years. The present investigation was undertaken during 2014 to 2018 to evaluate the effect of cowpea (Vigna unguiculata) co-culture with maize (Zea mays L.) on productivity enhancement over prevailing maize-fallow system, and to assess the feasibility of inclusion of short duration winter crops after maize with appropriate residue management practices on productivity and soil health. The experiment comprised of six cropping systems in main plot and three soil moisture conservation (SMC) measures options in sub plot. Results indicated that the inclusion of second crop in place of fallow and cowpea co-culture with maize increased average maize grain yield by 6.2 to 23.5% as compared to that of maize-fallow (MF). Use of maize stover mulch (MSM) + weed biomass mulch (WBM) increases maize grain yield by 19.1 and 6.5% over those of MSM and no mulch (NM), respectively. Various soil moisture conservation (SMC) measures had significant (p=0.05) effect on crop yields and water productivity. Double cropping system had significantly (p=0.05) higher amount of soil available NPK, soil organic carbon (SOC), microbial biomass carbon (MBC) and dehydrogenase activity (DHA) at 0-15 cm and at 15-30 cm depth than those under MF. The SWC measures of MSM+WBM had significantly higher available N, SOC, and MBC by 5.5, 4.8 and 8.1% than those under NM, respectively. Correspondingly, soils under MSM and MSM+WBM had 2.24 and 2.99% lower bulk density (ρb) in 0-15 cm and 2.21 and 2.94% lower ρb in 15-30 cm than that of NM. The energy use efficiency (EUE) was significantly higher under MCV (7.90%) over rest of the cropping sequences. MSM+WBM and MSM recorded 25.1 and 16.6% higher net energy over NM, respectively. The net return (INR 159.99×103/ha) and B:C ratio (2.86) were significantly higher with MCV system followed by MCR cropping sequence. MSM+WBM had significantly higher net return (INR 109.44×103/h), B:C ratio (2.46) over those under MSM (INR 97.6×103/h) and NM (INR 78.61×103/h). Overall the cowpea co-culture with maize and inclusion of short cycle winter crops along with MSM+WBM in maize-based cropping systems was found productive in terms of crop and water, profitable, energy efficient and sustained the soil health.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

Original and improved version of the Hardy Cross iterative method with related modifications are today widely used for calculation of fluid flow through conduits in loops-like distribution networks of pipes with known node fluid consumptions. Fluid in these networks is usually natural gas for distribution in the municipalities, water in waterworks or hot water in district heating system, air in the case of ventilation systems in buildings or mines, etc. Since, the resistances in these networks depend of flow, problem is not linear like in electrical circuits, and iterative procedure must be used. In both version of the Hardy Cross method, in original and in the improved one, initial results of calculation in iteration procedure is not flow, but rather the correction of flow. Unfortunately, these corrections should be added to or subtracted from a flow calculated in previous iteration according to complicate algebraic rules. After the here presented node-loop method, final results in each of the iterations is flow directly rather than flow correction. In that way complex algebraic scheme for sign of flow correction is avoided, while the final results still remain unchanged. Numbers of required iterations for the same results are comparable with the improved Hardy Cross method.

Increasing salt intake has substantial negative impacts on health and well-being. This review article focusses on the effect of salinity intrusion (SI) on the water quality and community health of coastal Bangladesh and to find out the effectiveness of interventions for reducing the negative effects of salinity. Saline water is a noteworthy reason for hypertension or high blood pressure in the coastal areas. Health status of women especially the pregnant women are vulnerable because of drinking water sodium (DWS) prompting to pre-eclampsia, high blood pressure and hypertension as well as infant mortality. Several interventions such as rainwater harvesting and Pond sand filter (PSF) system as well as managed aquifer recharge (MAR) usage and the integration of mixed sources were reviewed on the content of drinking water sodium (DWS). Although rainwater has the positive impact of low or no sodium intake on human health, it still possesses negative impacts from not having vital minerals. Despite what might be expected, in MAR a steady increment in sodium concentration through the span of the dry season was observed. It is, subsequently, important to increase awareness about drinking water sodium (DWS) intake by providing and adopting correct technological interventions.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

Object. Flooding in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous. In an average year floods on the rivers of Volyn region take place from one to three times which extend beyond the limits of the floodplain. The floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Methodology. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. Based on the statistical data of the Volyn Regional Center for Hydrometeorology during the 7 year period 2011-2017 about water levels of the river Styr. We conducted mathematical modeling of fluctuations of water levels within the territory of Lutsk, based on creating a partial Fourier series for discrete values of middle-ten-day water levels values. The post hydrological measurements of Styr river water levels in the territory of Lutsk located on the Shevchenko Street comply with an altitude 172.87 meters. Based on the data of short-term flood forecasting in February and March, and relief data from the Department of Architecture and Urban Development of Volyn State Administration, we conducted visualization of the results using geographic information system QGIS. Results. The results of mathematical processing were the basis for geoinformation simulation of flooded areas using remote sensing data that are publicly available. Use of statistical and geospatial data in this article has great potential for further application in modeling the processes of natural and technogenic origin. Scientific novelty. The mathematical model of short-term forecasting of water levels during the flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed. Practical significance. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The spring flood in February-March 2018, with the maximum water level 5.33 m, corresponds to an absolute mark of 178.20 m, which is forecasted in this article.

This paper proposes an Integrated Fire Management (IFM) framework that can be used to support communities and resource managers in finding effective and efficient approaches to prevent damaging fires, as well as maintain desirable fire regimes in Kenya. Designing and implementing an IFM approach in Kenya calls for a systematic understanding of the various uses of fire and the underlying perceptions and traditional ecological knowledge of the local people. The here proposed IFM framework allows an evaluation of the risks posed by fires, while balancing them with their beneficial ecological and economic effects, and thus developing effective fire management approaches. A case study of the proposed IFM framework was conducted in Gathiuru Forest that is part of the larger Mt. Kenya Forest Ecosystem. Focus group discussions were held with key resource persons, primary and secondary data on socio-economic activities were studied, fire and weather records were analyzed and the current fire management plans were consulted. Questionnaires were used to assess how the IFM is implemented in the Gathiuru Forest Station. The results show that the proposed IFM framework is scalable and can be applied in places with fire-dependent ecosystems as well as in places with fire-sensitive ecosystems in Kenya. The effectiveness is dependent on the active participation, formulation and implementation of the IFM activities by the main stakeholder groups (Kenya Forest Service (KFS), Kenya Wildlife Service (KWS), and the Community Forest Associations (CFA)). The proposed IFM framework helps in implementing cost-effective approaches to prevent damaging fires and maintain desirable fire regimes in Kenya.

Floods in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous signs. In an average year in the rivers of Volyn passes from one to three floods with going beyond the limits of the floodplain. Floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The mathematical model of short-term forecasting of water level in flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed.

Urban development and planning are increasingly centered on matters of sustainability, balancing economic development with ecosystem services and biotic structures within urban environments. In addition to these institutional and structural factors, the decision-making process within individual households must be understood to address rising concerns about water use. Therefore, individual characteristics and preferences that influence the use of water also warrant examination. In response to a survey of occupants of single-family residences in the Fresno Clovis Metropolitan Area of California, contextual interviews and focus group interviews with a homeowner sub-sample, we find evidence of an interplay of social-structural, institutional, and cultural factors involved in influencing individual water use behaviors and landscape decision making. The complexity of residential behaviors and decision-making poses some potential issues with regards to the interactions between individual households and institutional actors in matters of water usage and landscaping, as survey respondents indicate relatively little confidence in institutions and groups to make wise water policy decisions. We conclude that the promotion and implementation of sustainable water use practices will require not only environmental education for the citizenry, but also a tailoring of information for environmental educational initiatives that address the particularities of individual neighborhoods and communities.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

A novel experimental technique, quasi-equilibrated temperature-programmed desorption and adsorption (QE-TPDA) was used to study the water sorption properties and hydrothermal stability of aluminum trimesate MIL-96 and aluminum isophthalate CAU-10, which have been selected due to their remarkable sorption properties. The QE-TPDA profiles of water observed for MIL-96 and CAU-10 confirmed the hydrophilic nature of these materials. Complex QE-TPDA profiles indicate that water sorption in MIL-96 follows a three-step pore filling mechanism. The shape of single desorption peaks in the QE-TPDA profiles for CAU-10 confirms that water sorption involves a reversible phase transition. Based on the QE-TPDA profiles, the water adsorption heat were determined: 45-46 kJ/mol for CAU-10 and 43-56 kJ/mol for MIL-96, in the latter case depending on the adsorption extent. Hydrothermal stability tests revealed that MIL-96 retained its stable porosity-related sorption capacity for water after hydrothermal treatment up to 290°C. Gradual changes in the QE-TPDA profiles due to the hydrothermal treatment above 290°C, with decreasing the high-temperature desorption peak and increasing the low-temperature one, indicate minor structural changes occurring in this material. Only after 410° C treatment was fast degradation of MIL-96 observed. CAU-10 exhibited high and unchanged hydrothermal stability up to 400°C.

Limited evidence on hepatitis A seroprevalence among HIV-exposed uninfected (HEU) children compared to their HIV infected (HIV) and unexposed uninfected (HUU) counterparts compromises rational vaccine decision-making. This study comprised of a retrospective health facility-based population of children aged 1 month – 12 years. Archival sera were tested for markers of acute (anti-HAV IgM) or past (total anti-HAV) HAV infection. Subgroup analysis was conducted based on HIV exposure or infection status. Of 513 participants, 54% (277) were male and the median age was 10 (IQR: 4 – 25) months. The median maternal age was 29 (IQR: 25 – 34) years. An anti-HAV seropositivity of 95.1% (117/122 [95% CI 90.2-98.4]) was found among those ≤6 months of age, indicative of the rate of transplacental antibody transfer. Among 1–12-year-olds, hepatitis A seroprevalence was 19.3% (37/192 [95% CI 14.1-25.7]), while 1.1% (2/188 [95% CI 0.12-2.76]) had evidence of acute infection. Compared to HIV-exposed subgroups (HIV=60%, 6/10 [95% CI 27.4-86.3] and HEU=45%, 9/20 [95% CI 23.8-68]), hepatitis A seroprevalence among HUU children was low (29.2%, 47/161 [95% CI 22.4-37.0]). Natural immunity among HIV -exposed and -unexposed children in South Africa is insufficient to protect against severe liver complications associated with HAV infection later in adulthood.

In the study of mountainous areas, mountain peaks play a vital role as geomorphic features that have significant influence on hydrological processes, vegetation distribution, and other important topographic characteristics. From the perspectives of geomorphology and hydrology, the river network water system is an interconnected entity that serves as a crucial component in describing regional topography, geomorphology, and hydrological features. The primary objective of this article is to extract water system information and mountain peak data in Chongli District, Hebei Province. To extract mountain peaks, coarse-resolution Digital Elevation Model (DEM) data is utilized to estimate their positions and initiate data sampling based on DEM elevations. Deep learning models are employed to avoid explicit feature extraction and instead implicitly learn from training data. By using weight sharing techniques, the training parameters of the network are reduced, achieving more accurate extraction and recognition of mountain peaks in Chongli District, along with their classification. For the extraction of the water system, the fast regional convolutional neural network algorithm from target detection is introduced to enhance the efficiency and accuracy of extracting water system information through image processing. This algorithm rapidly identifies the type, location, and width of the water systems. Additionally, the AlexNet transfer learning method is applied to locate the river skeleton within the extracted water system area. Morphological methods are then used to extract river morphology and calculate its length and width. Finally, a developed algorithm for water system information extraction detects the presence of water system coverage areas in Chongli District. Through experiments, a total of 2792 mountain peak data points were successfully extracted. In terms of water system information extraction, the Faster R-CNN and CNN-based methods demonstrate high efficiency and low detection rates. This study provides information services and data support for the operation and maintenance of the Chongli Winter Olympics. Furthermore, it serves as a reference for future research conducted by scholars in the Chongli area, offering insights into various fields such as environmental changes, vegetation classification, and geomorphic features.

The study on the sustainable utilization capacity of water resources is of great significance for the realization of sustainable water resources management and development in the water-scarce regions of Northwest China. It provides insights into the potential for sustainable utilization of these resources. To evaluate the sustainable utilization capacity of the Huangshui Basin, a comprehensive evaluation index system was constructed based on three aspects: climate factors, water resources systems, and socio-economic factors. The evaluation was conducted using two methods: the fuzzy comprehensive evaluation model and the ELECTRE III evaluation method. The results indicate that the Huangshui Basin's water resources, as a whole, exhibit a medium sustainable utilization capacity. Climatic factors and socio-economic characteristics are the main factors affecting the sustainable utilization of water resources in the Huangshui Basin. Based on the results, measures such as strengthening the introduction of external water resources, enhancing water resources management, and implementing comprehensive remediation efforts in the basin can improve the level of sustainable use of water resources. The research results can provide a reference for decision-making regarding the evaluation of sustainable utilization capacity of water resources in water-scarce areas and the optimization of water resources management in the Huangshui Basin.

The term ‘photocatalysis’ has recently gained high popularity, and various products using photocatalytic functions have been commercialized. Of all the materials that may be used as photocatalysts, TiO₂ is virtually the only one that is now and most likely will remain appropriate for industrial application. Water and air purification systems, sterilization, hydrogen evolution, self-cleaning surfaces, and photoelectrochemical conversion are just a few of the products and applications in the environmental and energy domains that make extensive use of TiO₂ photocatalysis. This is due to the fact that TiO₂ has the lowest cost, most stability, and most effective photoactivity. Furthermore, history attests to its safety for both people and the environment because it has been used as a white pigment since antiquity. This review discusses some important aspects and issues concerning different synthesis methods and their influence on the structure and properties of TiO₂, as well as the concept of photocatalysis based on it as a promising biocompatible functional material that has been widely used in recent years. The advantages of TiO₂ applications in various fields of science and technology are discussed, including environmental protection, photocatalysis including self-cleaning surfaces, water and air purification systems, hydrogen liberation, photovoltaic energy, cancer diagnosis and therapy, coatings and dental products, etc. Information on the structure and properties of TiO₂ phases, as well as modern methods of synthesis of functional materials based on them are presented. This is followed by a detailed review of the basic principles of TiO₂ photocatalysis with a brief introduction to the modern concept of TiO₂ photocatalysis. Finally, the challenges and prospects of TiO₂ photocatalysis for various applications are briefly discussed. Recent advances in the fundamental understanding of TiO₂ photocatalysis at the atomic-molecular level are highlighted, and important recent advances in TiO₂ photocatalysis are summarized in terms of the design and engineering of new materials.

The growing prevalence of disposable toilet seat covers in public restrooms stems from concerns about personal hygiene, given the direct contact between the seat and various users' skin. To enable flushing these disposable cover sheets down the toilet instead of discarding them in the trash, they must possess specific properties. These include rapid water absorption for quick disintegration, strength to endure user movement or moisture on the toilet seat surface, and a comfortable texture. To address these challenges, the study investigated the disintegration characteristics of flushable cover sheets prepared under different refining conditions. Alkyl ketene dimer (AKD) was also employed to enhance water resistance, while an organic antibacterial agent was used to impart antimicrobial properties. The findings revealed that adding 0.2% AKD and 1% organic antibacterial agent to pulp stock with a freeness of about 650 mL CSF was suitable for manufacturing disposable cover sheets with disintegration characteristics like toilet tissue paper.

The study reveals correlations between the parameters of ions and their HOMO and LUMO orbital energy level values. In particular, it demonstrates a clear correlation for the ion adsorption parameters on model electrodes: the aluminum oxide (0001) surface, graphene and Au (111) surface. Correlations are also observed for the parameters of ion binding to water and dimethyl carbonate molecules, which are often used as solvents. In addition, the dipole moment, polarizability and solvation energy of ions are well correlated with the values of the molecular orbital energies, and for anions a dependence on the oxidation potential is observed. The obtained descriptors make it possible to select ions with desired values for a specific problem. As an illustrative example, in this work we consider the problem of displacement of water molecules from the inner electric double layer by ions, which is one of the factors increasing the potential window in electrolytes of aqueous batteries. This approach can be applied in the rapidly developing field of aqueous electrolytes for battery or supercapacitor design, catalysis control through surface composition variations, as well as in studies of heavy metal ion binding to sorption materials.

Quinacridone (QA) and 2,9-dimethylquinacridone (DQA) are synthetic substances suitable as a hard, abrasion-resistant, self-organizing gliding layer on ice, snow, and water. For sustainable use, a large number of parameters must be considered to demonstrate that these non-biogenic substances and their by-products and degradation products are harmless to humans and the environment in the quantities released. For this task, available experimental data are used and supplemented for all tautomers by numerous relevant physical, chemical, toxicological and ecotoxicological estimated values based on various Quantitative Structure Activity Relationship (QSAR) methods. On the one hand, the low solubility of QA and DQA leads to stable gliding layers and thus low abrasion and uptake by plants, animals, and humans. On the other hand, the four hydrogen bond forming functional groups per molecule allow nanoparticle decomposition and enzymatic degradation in natural environments. All available data justify a sustainable use of QA and DQA as a gliding layer. The assessment of the toxicological properties is complemented with an investigation of the size and morphology of DQA particles as well as field tests indicating an excellent performance as a gliding layer on snow.

Seasonal precipitation variance significantly alters soil water content, potentially inducing water stress and affecting plant transpiration in semiarid deserts. This study explored the effects of environmental variables and hydraulic conductance on whole-tree transpiration (ET) in Mongolian pines (Pinus sylvestris var. mongolica) across different forest stages in the semiarid deserts of northern China. We measured ET using sap flow in mature (MMP), half-mature (HMP), and young (YMP) Mongolian pine plantations. Measurements included soil-leaf water potential difference (ΔΨ), atmospheric conditions, and soil moisture contents on sunny days, both in dry and wet periods. Seasonally variable rainfall distinctly affected soil moisture, correlating ET with photosynthetically active radiation (PAR) and vapor pressure deficit (VPD). Notable nocturnal sap flow occurred during the growing season. During the dry periods, both stomatal and hydraulic conductance influenced ET, whereas during the wet periods, stomatal conductance primarily regulated it. Discrepancies between predicted and measured ET were noticed: compared to the predicted ET, measured ET was lower during dry periods while higher during wet periods. Hydraulic conductance (KT) increased with tree height (H) and ΔΨ, although tall trees exhibited lower KT rates, suggesting that hydraulic compensation had occurred. This compensation, observed between 11:00 and 13:00, aligned with increased hydraulic resistance during dry periods. Decreasing hydraulic conductance intensified leaf water stress in dry periods, especially during the time when PAR and VPD were heightened, potentially increasing stomatal sensitivity to drought, promoting water conservation and plant survival. A linear relationship between predawn and midday leaf water potentials was noticed, indicating extreme anisohydric behavior across forest stages during both dry and wet periods. Although both stomatal and hydraulic conductance influenced ET during the dry period, MMP and YMP were more susceptible to drought conditions. Understanding these dynamics could help evaluate semiarid desert ecological functions for water conservation amidst uneven seasonal precipitation in Northern China.

Nuʻupia Ponds, a traditional Hawaiian fishpond system, are located at Marine Corps Base Hawaii (MCBH) and part of the Nuʻupia Ponds Wildlife Management Area, a wetland refuge for native, endangered, and protected birds and Hawaiian green sea turtles, as well as many native fish species. Currently, there is uncertainty regarding the ecological status and condition of the fishponds following prior modification of wetland habitats in and around the ponds. This study examines circulation dynamics and characterizes water exchange, pond volume, and residence time across the full tidal spectrum at Nuʻupia fishponds. Our results indicate a general west to east gradient in current flow; with higher flushing rates and lower residence times of fishponds in the western ponds of the Nu’upia system compared to the eastern ponds. We further found low flushing rates at several sites causing limited water exchange with Kāne’ohe Bay, as well as within Nu’upia Pond system. Sufficient water circulation plays a fundamental role in maintaining a healthy balance of fishpond flora and fauna and preserve ecosystem health. The results from this study provide a baseline of current physical water circulation dynamics and implications for ecosystem health, as well as inform science-based conservation and management strategies moving forward.

Heavy metals represent a class of chemical elements that includes metalloids, bases and transition metals, lanthanides and actinides. They are distinguished for their toxicity in small concentrations and for their negative effects on the environment and human health. They are present in various samples, mainly in water, industrial waste and food. The determination of heavy metals is carried out mainly by analytical methods, using spectroscopy, spectrometry and electroanalysis, while studies are being carried out for the development of new and faster methodologies and techniques for their analysis, with particular emphasis on voltammetry. This review deals with the determination of heavy metals mainly in environmental samples (water) using voltammetry. In particular, the methods of their determination are evaluated in terms of sensitivity, selectivity and applicability.

Counter-current spontaneous imbibition of water is a critical oil-recovery mechanism. In the laboratory, the Amott test is a widely used technique to assess efficacy of brine imbibition into oil-saturated core plugs. The classic Amott-cell methodology was designed to estimate ultimate oil recovery, but not the recovery dynamics that provides essential information about the imbibition mechanisms. Retention of oil droplets at the external core surface and delayed onset of oil production are the two key artifacts of the classic Amott experiment. This retention, referred to here as the ``external-surface oil holdup effect'', often results in stepwise recovery curves that obscure true dynamics of spontaneous imbibition. To address these holdup drawbacks of the classic Amott method, we modified the Amott cell and experimental procedure. For the first time, using water-wet Indiana limestone cores saturated with brine and mineral oil, we showed that our improvements of the Amott method enabled accurate and reproducible measurements of oil-recovery dynamics. We used the Generalized Extreme Value (GEV) statistics to describe oil-production histories from water-wet heterogeneous limestone cores with finite initial water saturations, for the first time. We demonstrated that our four-parameter GEV model accurately described the recovery dynamics, and that optimal GEV parameter values systematically reflected the key characteristics of the oil-rock system, such as oil viscosity and rock permeability. These findings gave us a more fundamental understanding of spontaneous, counter-current imbibition mechanisms and insights into what constitutes a predictive model of counter-current water imbibition into oil-saturated rocks with finite initial water saturation.

The digital transformation of critical infrastructures, such as energy or water distribution systems, is essential for their smart management. Faster issue identification and smoother services enable better adaptation to consumers' evolving demands. However, these large-scale infrastructures are often outdated. Their digital transformation is crucial to enable them supporting societies. This process must be carefully planned, providing guidance that ensures that the data they rely on is dependable and that the system remains fully operational during the transition. This paper presents a formal model that supports reliable data acquisition in legacy critical infrastructures, facilitating their evolution towards a data-driven smart system. Our model provides the foundation for a flexible transformation process while generating dependable data for system management. We demonstrate the model's applicability in a use case within the water distribution domain and discuss its benefits.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

A qualitative analysis of pressure acting within the human eye is presented. The situation emerging within the human eye in rest and human eye of accelerated/training person should be distinguished. When the person is in rest, the hydrostatic pressure is much larger than the Laplace pressure. The dynamic (Bernoulli pressure) emerging from intraocular flows in this case is negligible. The situation is rather different for accelerated or decelerated person. In this case, the dynamical pressure and the water hammer pressure become dominant. Under certain circumstances, the water hammer pressure may be larger than the ultimate tensile strength of retina, choroid and the Bruch membrane‐choroid complex, which may possibly affect the retina. As a recommendation: physical training, which is not accompanied with ultimate acceleration/acceleration of the body, may be performed after posterior vitreous detachment; however, potentially traumatic activities such as boxing or competitive diving should be avoided.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

A paddle wheel aerator is developed in this research, which includes a wireless sensor network for measuring the water quality in the aquaculture of marine shrimp ponds. It can also move to the desired position to fill oxygen and measure water quality. A basic requirement is good standard water quality to prevent shrimp from epidemics and improve production. The water quality paddle wheel aerator applies a microcontroller and sensors to measure eight parameters of water quality. These water quality parameters are observed on the web application via an IoT module. The movement system of the water-quality paddle wheel aerator consists of a LiDAR, GPS, and remote RF signal. Each item of data is recorded immediately on the cloud server while the water-quality paddle wheel moves in the marine shrimp farm. The controlled paddle wheel aerator is harnessed automatically to enhance precisely the spatial monitoring resolution of the measurement system installed, which is needless for a multiple measurement system with high cost of investment. Also, farmers can access real data through the Line application. Hence, they are able to plan and control a good environment for aquaculture, preventing the occurrence of various epidemics and decomposing organic matter in the pond.

Irrigation and fertilization are indispensable links in the jujube planting industry in southern Xinjiang, China. However, the water and fertilizer integration effects on jujube growth and fruit quality remain unclear. A two-year water and fertilizer optimization coupling test was conducted to determine the optimal water- and nutrient-supply scheme. The three-factor randomized block experiment included water (W), nitrogen (N), and phosphorus (P). According to the principal component analysis of each index, each treatment’s comprehensive score was obtained. Using yield and economic regression models, the theoretical value and yield value of the optimal economic benefit are inferred. When W, N, and P were applied together, the fruit quality and yield of each treatment significantly differed, and the vitamin C, soluble sugar, and sugar–acid ratio increased significantly with an increase in nitrogen fertilizer. However, the titratable acid decreased. An increase in irrigation and nitrogen application significantly increased fruit yield. The comprehensive score was the highest in the N3P3W2 treatment, which improved fruit quality, and the lowest in the N4P3W2 treatment. When the amounts of N, P, and W were 275.56 kg·hm-2, 413.66 kg·hm-2, and 7278.19 m3·hm-2, respectively, the theoretical economic benefit was the best. The N4P3W2 treatment is the optimal treatment.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

The global rising demand for exploiting limited shared groundwater resources, coupled with significant water deficit, especially in arid and semi-arid regions, has led to escalating conflicts among stakeholders. As such, using Bankruptcy Theory methods can be an appropriate response to the reallocation of resources. This study introduces a novel approach to weighted Bankruptcy, where the relative importance of stakeholders is determined by their contributions to sustainable development, and the impact of their claims on the shared groundwater resources is considered. The framework is implemented in a two-level bankruptcy process including the plains and their beneficiaries (agriculture, drinking and industry). The proposed two-level weighted bankruptcy process applies to the Neyshabour-Ataiyeh-Sabzevar plains in Iran. The process is implemented for two scenarios including the Baseline scenario related to the present status of demands and the Future scenario associated with the estimated demands for the year 2041. To compare the weighted proposed method with the other weighted methods such as Proportional (WPRO), Constrained Equal Awards (WCEA), Pinile (WPIN), Talmud (WTAL), Constrained Equal Losses (WCEL), Modified Constrained Equal Losses (MWCEL), two categories including the deficit-based and resource-based approaches are considered. According to the stability analysis using the Bankruptcy Allocation Stability Index (BASI) method, among the deficit-based methods, the novel approach is chosen as the preferred method for the beneficiaries’ reallocation like the Sabzevar’s beneficiaries. Accordingly, it allocates 86.95%, 10.86% and 2.17% of the shared resource to the agricultural, drinking, and industrial demands, respectively. Among the resource-based methods, the WPIN method is selected for reallocation between the stakeholders and their beneficiaries in each level and scenario of reallocation. The novel approach offers a promising solution to the water resource reallocation problem, ensuring a more equitable and sustainable management of shared groundwater resources.

This study aimed to elucidate the antibacterial efficacy and unique chemical compositions generated from plasma-activated water (PAW) when utilized a novel vaginal cleansing device. We conducted an analysis of antibacterial activity against probiotics and several chemical compositions including ions under various operational parameters of PAW, including electrical power (12 and 24 V), treatment duration (1, 10, and 20 min), and stay duration (immediate, 30 and 60 min). Our findings revealed that as treatment duration increased, hypochlorous acid (HOCl), Ca2+, and Mg2+ concentrations increased and Cl−concentrations decreased. Higher electrical power and longer treatment duration resulted in increased HOCl levels, which acts to prevent the growth of general microorganisms. Notably, PAW exhibited no antibacterial effects against a type of probiotic, Lactobacillus reuteri that produces lactic acid for vaginal health. This result demonstrated the ability of the vaginal cleaning device to generate ions, primarily HOCl and some cations (Ca2+ and Mg2+), thereby providing vaginal mucosa protecting and cleansing effects with the vaginal environment.

The analysis of water inflow is a key issue in the construction of subsea tunnels. However, present research on the water inflow of subsea tunnels is predominantly focused on single-bore tunnels. Given the current practices in engineering, it is common to see a parallel configuration of three bores. In such cases, the proximity of tunnels to one another might result in alterations to the water inflow due to the interplay of seepage fields. This paper begins by conducting a numerical simulation to assess the water inflow characteristics of a three-bore parallel subsea tunnel. The study then investigates the impact of many factors, including the permeability coefficient of the surrounding rock, the depth of the seawater, the depth of the tunnel, the spacing between tunnels, and the relative size of the tunnels, on the water inflow phenomenon. Furthermore, based on the principles of the analytic hierarchy process and fuzzy mathematics, a comprehensive assessment framework is developed to evaluate the water inflow of three-bore parallel subsea tunnels. Ultimately, this grade of water inflow is used in practical engineering. The results show that there is mutual influence between the three parallel tunnels, and the predicted water inflow will be too large if the single tunnel model is adopted. The interaction between tunnels should be considered in the water inflow grade evaluation system of the three-hole parallel submarine tunnel. Engineering cases show that using a single-hole tunnel model without considering the interaction between tunnels will lead to higher water inflow grades. The research results of this paper can provide guidance for the waterproofing and drainage design of three parallel subsea tunnels and the stability analysis of surrounding rocks.

Women are at higher risk of cognitive impairment and Alzheimer’s disease (AD) after menopause when the estrous cycle becomes irregular and begins to taper off. Numerous studies have shown that estrogen deficiency, especially estradiol (E2), has been shown to play a key role in this phenomenon. Recently, a novel polymeric drug, hyaluronic acid-17β-Estradiol conjugate (HA-E2), has been developed which has the ability to cross the blood-brain barrier (BBB), facilitate a longer E2 release profile and lower risk of estrogen supplement related side effects. In this study, we used an ovariohysterectomy (OHE) rat model of postmenopausal cognitive deficits and explore whether HA-E2 treatment can improve the cholinergic septo-hippocampal innervation system, synaptic transmission in the hippocampal pyramidal neuron and cognitive impairment. Our results show that OHE rats after HA-E2 administration have increased expression of choline acetyltransferase (ChAT) in the medial septal nucleus (MS nucleus) and the hippocampus, increased spine density in hippocampal pyramidal neurons, and improved spatial learning and memory. Therefore, HA-E2 has great potential as a new novel class of drugs for estrogen-deficiency-induced cognitive impairment and AD.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Recently, the Internet of Things (IoT) has attracted wide attention from many fields, especially healthcare, because of its large capacities of information perception and collection. In this paper, we present an IoT-based home telehealth system for providing smart healthcare management for individuals, especially older people. Each client node of the system is mainly composed of an electronic water meter that records the user's daily water usage and an unobtrusive sleep sensor that monitors the user's physiological parameters during sleep such as heart rate (HR), respiratory rate (RR), body movement (BM), and states on the bed or outside the bed. The sleep sensor senses the biosignals and states by a sensor matrix composed of 12 piezoelectric sensors. The collected data can be transmitted to a remote centralized cloud service by a wireless home gateway for analyzing the living pattern and rhythm of users. Furthermore, the periodic feedback of results can be provided to users themselves as well as their family and health advisers. In the present study, data collections from a total of 18 older subjects were made for one year to evaluate the effectiveness of the proposed system. By analyzing living pattern and rhythm, preliminary results indicate the effectiveness of the telehealth system and suggest the potential of the system regarding improvement of quality of life (QoL) of older people and promotion of their health.

Data-driven models (DDMs) are extensively used in environmental modeling but face challenges due to limited training data and potential results not adhering to physical laws. To address this challenge, this study developed a process-guided deep learning (PGDL) model, integrating a long short-term memory (LSTM) neural network and a process-based model (PBM), CE-QUAL-W2 (W2), to predict water temperature in a stratified reservoir. The PGDL included an energy constraint term from W2's thermal energy equilibrium into the cost function of the LSTM, besides the mean square error term. In PGDL, parameters were optimized by penalizing deviations from the energy law, ensuring adherence to physical constraints. Compared to LSTM, PGDL demonstrated enhanced satisfaction with the energy balance and superior performance in water temperature prediction. Even with less field data for training, PGDL outperformed both LSTM and calibrated W2 after pre-training with data generated using the uncalibrated W2. Therefore, integration of DDM with a PBM ensured physical consistency in water temperature prediction for complex stratified reservoirs with limited data. Moreover, pre-training the PGDL with PBM proved highly effective in mitigating bias and variance due to insufficient field measurement data.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Sudden water pollution accident is a tough environmental challenge to solve due to its uncertainty, unpredictability and destructiveness. Therein, the dangerous goods transportation accidents on the cross-tributary bridges are increasing worldwide with the acceleration of industrialization and urbanization, posing threats to the water ecological environment and human health. To prevent and control the risk, this study evaluated the risk of sudden water pollution accidents associated with dangerous goods transportation on the cross-tributary bridges by using the expert judgment fuzzy language method and Bayesian network model. Baiyangdian lake as the largest freshwater shallow lake in North China was chosen as a study case. Different accident scenarios were simulated to put forward risk prevention and control measures. The results showed that the primary risk factors were divided into five categories: personnel factors, vehicle factors, tank factors, weather factors, and road environment factors. The probability of dangerous goods transportation accidents was a possible event (P=0.115), with a high risk level. Furthermore, the Baiyangdian lake would suffer from serious environmental pollution and water quality degradation without prevention and control measures by simulating the oil leakage accident. Therefore, emergency prevention and control measures are expected to be formulated and implemented before and after the occurrence of the sudden water pollution accidents. This study provides useful insights into risk prevention and control strategies for sudden water pollution accidents, and the framework can be made applicable to other rivers facing similar risk challenges worldwide.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

Forest damage has become more frequent in Europe in the last decades, and remote sensing offers a powerful tool for monitoring them rapidly and cost-effectively. A novel approach was developed to utilize high-resolution ESA Sentinel-2 satellite imagery and Google Earth Engine cloud computing. The processing, analysing, and visualization of vegetation and water index (NDVI, NDVIch, Z NDVI, EVI, NDWI) maps and charts derived from satellite images took place in the cloud to ensure the detection of forest disturbances in the Hungarian study site for the period 2017-2020. The index maps were classified to reveal forest disturbances, and the cloud-based method successfully showed drought and frost damage in the oak-dominated Nagyerdő forest of Debrecen. Differences in the reaction to damage between tree species were visible in the index values, therefore a Random Forest Machine Learning classifier was applied to show the spatial distribution of dominant species. Accuracy assessment was accomplished with confusion matrices that compared classified index maps to field-surveyed data, demonstrating 71% Total Accuracy for forest damage and 76% for tree species. Based on the results of this study and the resilience of Google Earth Engine, the presented method has the potential to be extended to monitor the entire Hungary.

Agriculture technical development exclusively relies on the effective delivery of agrochemicals and water to the plants and reduce the harmful effects of the agrochemicals on the useful organisms in the soil. Wherefore, super absorbent hydrogels were prepared by copolymerization of gum Arabic (GA) with chitosan (CS) or poly(vinyl alcohol) (PVA), and cross-linked by N,’N-methylenebisacrylamide (MBA) chemically (CH) or using sodium hexametaphosphate (SHMP) as physical (PH) cross-linker. The prepared hydrogels include PVA/GA-CH, PVA/GA-PH, CS/GA-CH and CS/GA-PH showed different degree of swelling (DS) in the following swelling medium, deionized water (DW), river water(RW) and buffer solution pH9. PVA/GA-CH and CS/GA-CH hydrogels have showed 84g/g and 63g/g maximum DS in RW respectively, while PVA/GA-PH and CS/GA-PH hydrogels have showed 81g/g and 69g/g maximum DS in pH9 respectively. The water- retention capability of some hydrogels were studied using a mixture of 0.5%(w/w) hydrogel in agricultural soil and the composite showed about 20 days extra retain of water with a control sample of soil alone. The hydrogels were loaded using urea the important fertilizer in agriculture field. The hydrogels of higher DS were only loaded, where PVA/GA-CH hydrogel has shown 89%(w/w) maximum loading percentage (Lmax%), and CS/GA-PH hydrogel reached 79.75%(w/w) of urea. The release behavior in different medium and degree of temperatures of loaded hydrogels were studied. Generally, PVA/GA-CH hydrogel have shown better release profile in RW medium at 10oC, while CS/GA-PH hydrogel showed more controlled release in pH9 medium at 30oC. Different analytical methods of SEM, FTIR of loaded hydrogel and after their release were achieved, whereas XRD,1H NMR and (TGA, DSC) of prepared hydrogels have been characterized.

Soil erosion due to soil erosion is an important ecological impact factor. In order to further explore the impact and contribution of soil and water conservation measures on sand production and transport in the watershed, and also to provide a reference for soil erosion control, soil and water conservation and ecological environmental protection in the Yellow River Basin. In this paper, based on the measured data from the Henan Soil and Water Conservation Observatory in the Yellow River Basin, we select appropriate equations for quantifying soil erosion factor to calculate the rainfall erosion, topography, soil, vegetation and soil conservation measures in the basin, and then analyse the changes in soil erosion factor and the actual benefits of soil conservation measures in the basin. The results show that there is an increasing trend in the rainfall erosion force factor R in the Yellow River Basin; Soil erosion can be K value made the vertical loess > yellow clunamon soil, the overall change shows a decreasing trend, indicating that erosion control has produced results and that attention should be paid to erosion control in the lithosol region in the future; Since the slope lengths of the runoff plots are laid out consistently with the same LS values for both topographic factors, soil erosion is severely increased when the slope exceeds 20°. The C value of natural vegetation is small, while the C value of bare land is large. The authorities should continue to promote the return of farmland to forests and grasses and pay attention to the self-regulation and restoration of ecosystems; There is an overall decreasing trend in the P value of the soil and water conservation measures factor, the soil and water conservation measures have been effective in providing good protection.

The development of knowledge graphs for water resources as a tool for studying sustainable regional development is a relevant task, as the increasing deterioration of water bodies affects the ecology, economy of the country, as well as the health of the population living near water bodies. Solving this problem requires the development of water resource monitoring methods based on semantic data analysis is required to detect and track sources of pollution and provide recommendations to support decision-making. This research proposes a method of semantic analysis for modeling knowledge graphs and constructing rules that enable the integration of data from heterogeneous sources, semantic compatibility, support for reasoning and inference, facilitate queries and search, and represent knowledge in the field of water resource monitoring. As a result, an ontology based on the SWRL language is created, which enables the expression of complex relationships and derivation of new knowledge, SSN for interaction between the ontology and sensor data, and Time Ontology, which models and analyzes information related to temporal aspects.After populating the ontology and establishing logical connections, SPARQL queries are implemented to retrieve new knowledge about water resources.

China is rich in coal resources under water bodies. However, for a long time, the safety prediction of high-intensity mining under water bodies is one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid-liquid coupling physical simulation test reveals the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole peeping with the height data of water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as -29.39 %. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and provide a scientific guarantee for the formulation of safety measures under such conditions.

Reducing the costs of repairing concrete structures damaged due to the appearance of cracks and reducing the number of people involved in the process of their repair is the subject of a multitude of experimental studies. Special emphasis should be placed on research involving industrial by-products, the disposal of which has a negative environmental impact, as is the case in the research presented in this paper. The basic idea was to prepare a mortar with added granulated blast furnace slag from Smederevo Steel Mill and then treat artificialy produced cracks with a Sporosarcina pasteurii DSM 33 suspension under the conditions of sterile demineralized and water from Danube river in order to simulate natural conditions. The results show a bio-stimulated healing efficiency of 32.02% in sterile demineralized water and 42.74% in Danube water already after 14 days. The SEM images clearly show calcium carbonate crystals as the main compound that has started to fill the crack, and the crystals are much more developed under the Danube water conditions. As a special type of research, microscopic images of cracks were classified into those with and without the presence of bacterial culture. By applying convolutional neural networks (ResNet 50), the classification success rate was 91.55%.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

Reservoir in the Central Structural Zone of the Xihu Sag is the Huagang Formation, dominated by natural gas reservoirs, and the reservoir in the Western Slope Zone is the Pinghu Formation, dominated by light oil and wet gas. In this paper, the Gas Drive Water Displacement- Magnetic Resonance Imaging (GWD-MRI) experiments are used to simulate the charging characteristics of the sandstone migration layer. The centrifugal- Magnetic Resonance (Cen-NMR) experiments simulate the short-term fast trap charging process, and the Semi-Permeable Baffle (SPB) charging experiment simulates the slow trap accumulation process. Studies have shown that there is a start-up pressure for the migration layer charging, and the start-up pressure of the core with a permeability of 0.3mD is about 0.6MPa. Experimental simulations have confirmed that there is a front zone with changed water saturation, with a width of about 1-1.5cm. The migration layer charging mainly has two actions, drive effect and carry effect. The drive effect reduces the water saturation to 70%-80%, and the carry effect can still reduce the water saturation by 5%-10%. The water saturation of rapid charging is mainly affected by the petro-physical. The porosity is high, the water saturation is low. The water saturation decreased significantly with the increase of centrifugal force when the centrifugal force is smaller. If the centrifugal force is greater than 0.8 MPa, the water saturation decreases slowly. The water saturation of the trap slowly charging is basically maintained at 40%-50%, which matches the water saturation of the airtight coring from 40%-55%, the petro-physical do not affect the final water saturation.

Water quality is the measure of chemical, physical and biological suitability of water in relation to natural effects and intended purpose which may affect human health and aquatic life. Assessment of water quality is very essential for the management of water resources and human health. Traditionally, in-situ measurements have been used to obtain the water quality parameters of the water bodies. However, with the availability of satellite images, researchers have shown that satellite images are a reliable tool that can be used to estimate water quality. Satellite image-derived water quality parameters provide extensive spatial extent and large temporal variations when compared to traditional in situ sample collection and laboratory measurements. The present work estimated several parameters for quality of water in the Kamuzu reservoir of Lilongwe River for the 2013-2020 period using Sentinel-2 and Landsat-8 satellite images. The band ratio algorithms were used to retrieve Chlorophyll a (Chl-a), Turbidity, Total Suspended Matter (TSM), Secchi depth, Coloured Dissolved Organic Matter (CDOM), and Cyanobacteria from the reservoir. Turbidity and TSM were compared with the in-situ data collected over the same period. The comparison indicated R² of 0.9 and 0.69 for TSM and Turbidity respectively from Sentinel-2 images whereas R² of 0.56 and 0.61 was obtained using Landsat 8 images which are quite encouraging. The other set of results included the spatial distribution maps of water quality parameters using Landsat-8 and Sentinel-2 satellite data. It was observed that the spatial distribution of water quality parameters, except for CDOM and Cyanobacteria, showed very good distribution and matches with the theoretical results. However, for CDOM and Cyanobacteria, the distribution was almost similar for the entire study area and the band ratio algorithm may not be able to estimate them quite reasonably. This research reiterates the need for the use of remote sensing in estimating the water quality parameters and may be a substitute to the in-situ data, in terms of spread and frequency, which is very common to most of the water bodies, across the globe.

The threat posed by climate change, the progressive erosion of natural resources, the polluting effects related to private motorization, energy waste, excessive consumption of agricultural and natural soils and their progressive waterproofing and reduction in vegetation cover, with the subsequent environmental degradation, have highlighted the need for a sustainable management of natural resources, in terms of an equitable and ethical development, to build inclusive communities able to adapt to the negative effects of emergency phenomena, through new capacities of economic, cultural and social resilience. This contribution presents the results of the activities conducted in the RivEr/Generation_LAB, a project organized by three CIVIS members (Sapienza University of Rome, Universitè libre de Bruxelles, Universidad Autonoma de Madrid) as a part of the CIVIS Project "RivEr/Generation_LAB. Linking resilience with inclusiveness in the urban built environment of Rome, Brussels, and Madrid", financed into the Hub4 Cities, Territories & Mobilities’ Call for proposals 2021. The project proposes a methodology of intervention in the Flaminio district, in particular on the 'Olympic Village' and its relationship with the Tiber River, in line with the Sustainable Development Goals, the Millennium Ecosystem Assessment and the New European Bauhaus, to establish new relationships between cities and the natural environment, favouring sustainable and inclusive public spaces.

Drought is one of the most serious abiotic stressors in the environment, restricting agricultural production by reducing plant growth, development, and productivity. To investigate such a complex and multifaceted stressor and its effects on the plants, a systems biology-based approach is necessitated, entailing the generation of co-expression networks, identification of highly-priority transcription factors (TFs) dynamic mathematical modeling, and computational simulations. Here, we studied a high-resolution drought transcriptome of Arabidopsis. We revealed distinct temporal transcriptional signatures and demonstrated the involvement of specific biological pathways. Generation of a large-scale co-expression network followed by network centrality analyses identified 117 TFs that possess critical properties of hubs, bottlenecks, and high clustering coefficients nodes. Dynamic transcriptional regulatory modeling on integrated TF-target and transcriptome datasets uncovered major transcriptional events during the course of drought stress. Mathematical transcriptional simulations allowed us to ascertain the activation status of major TFs as well as the transcriptional intensity and amplitude of their target genes. Finally, we validated our predictions by providing experimental evidence of gene expression under drought stress for a set of four TFs and their major target genes using qRT-PCR. Taken together, we provided a systems-level perspective on the dynamic transcriptional regulation during drought stress in Arabidopsis and uncovered numerous novel TFs that can potentially be used in future genetic crop engineering programs.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

Degraded soils causing from natural and human affects are universal in arid and semi-arid regions all over the world. Bentonite and humic acid (BHA) are increasingly being tested to remediate these degraded lands with potential benefits on crop production and soil health. The objective of this paper was to determine the residual effects four to five years after a one-time BHA application at six rates on (i) dynamic changes in soil properties, and (ii) oat crop productivity parameters, in a dryland farming ecosystem. With increasing rates of one-time BHA application, soil profile water storage displayed a piecewise linear increase plus plateau, whereas soil electrical conductivity, pH and bulk density were all reduced significantly (P < 0.05) in the 0-20 cm and 20-60 cm layers. The improved soil environments gave rise to an increased activity of soil enzymes urease, invertase and catalase that respectively reached the peak values of 97%, 37% and 32% at the rates of 21 to 24 Mg BHA ha-1. These conversely boosted soil nutrient turnover, leading to a 40% higher soil available P. Compared with the control treatment, application of BHA at the estimated optimum rate (roughly 24 Mg ha-1) increased grain yield by 20%, protein yield by 62%, water use efficiency by 41%, and partial factor productivity of N by 20%. Results of this study showed for the first time that a one-time BHA application would be a new and effective strategy to combat land degradation, drought, and promote a sustainable soil micro-ecological environment in dryland agroecosystem under a varying climate scenario.

In this paper, we present a method for detecting and quantifying pathogens in water samples. The method proposes a portable dark field imaging and analysis system for quantifying E. coli concentrations in water after being labeled with magnetic particles. The system utilizes the tracking of moving micro/nano objects close to or below the optical resolution limit confined in small sample volumes (~ 10 µl). In particular, the system analyzes the effect of volumetric changes due to bacteria conjugation to magnetic microparticles (MP) on their Brownian motion while being suspended in liquid buffer solution. The method allows for a simple inexpensive implementation and the possibility to be used as point-of-need testing system. Indeed, a work-ing prototype is demonstrated with the capacity of quantifying E. coli colony forming units (CFU) at a range of 1x10³ - 6x10³ CFU/mL.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

Life cycle assessment (LCA) is being included formally in EcoDesign regulations. Especially product carbon footprint will be mandatory in Europe. However, life cycle impact assessment including global warming potential (GWP) in LCA is hampered by several challenges. One of these is lack of water vapor characterization indexes for GWP. A life cycle inventory profile for air transport fuel including water vapor emissions is evaluated with state-of-the-art practice, i.e. EF Method and ILCD 2011 Midpoint+ and neglecting water vapors high altitude GWP compared to carbon dioxide. Then the characterization factor in GWP100 for water vapor and alternate normalization for particulates are introduced. The results are compared. The main findings are that the EF method and ILCD both generate rather realistic results for Particulate Matter and Respiratory Inorganics mid-point indicators, respectively, but the amount of premature deaths should be better allocated to different specific emissions, and that water vapor may dominate the GWP100 result over the usual carbon dioxide. LCIA mid-points need measurable and understandable bases. The common knowledge of water vapor’s GWP100 should not be neglected in LCIA for air transport and beyond where relevant.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

Whereas a vast literature exists on satellite-based mapping of rice paddy fields in Asia, where most of the global production takes place, little has been produced so far that focuses on the European context. Detection and mapping methods that work well in the Asian context will not offer the same performances in Europe, where different seasonal cycles, environmental contexts, and rice varieties make distinctive features dissimilar to the Asian case. In this context, water management is a key clue; watering practices are distinctive for rice with respect to other crops, and within rice there exist diverse cultivation practices including organic and non-organic approaches. In this paper, we focus on satellite-observed water management to identify rice paddy fields cultivated with a traditional agricultural approach. Building on established research results, and guided by the output of experiments on real-world cases, a new method for analysing time series of Sentinel-1 data has been developed, which can identify traditional rice fields with a high degree of reliability. This work is a part of a broader initiative to build space-based tools for collecting additional pieces of evidence to support food chain traceability; the whole system will consider various parameters, whose analysis procedures are still at their early stages of development.

Wave breaking is one of the most important yet poorly understood water wave phenomena. It is via wave breaking that waves dissipate most of their energy and the occurrence of wave breaking directly influences several environmental processes, from ocean-atmosphere gas exchanges to beach morphodynamics. Large breaking waves also represent a major threat for navigation and for the survivability of offshore structures. This paper provides a systematic search for intermediate to deep water breaking waves with particular focus on the elusive occurrence of plunging breakers. Using modern remote sensing and deep learning techniques, we identify and track the evolution of over four thousand unique wave breaking events using video data collected from La Jument lighthouse during ten North Atlantic winter storms. Out of all identified breaking waves (Nb=4683), ≈22% were dominant breaking waves, that is, waves that have speeds within [0.77cp, 1.43cp], where cp is the peak wave speed. Correlations between the occurrence rate of dominant breaking waves (that is, waves per area and time per peak wave period) and wave steepness and wave age were observed. As expected, the number of identified plunging waves was small and six waves of all detected breaking waves, or 0.13%, could undoubtedly be considered as plunging waves. Two waves were also identified as unusually large, or rogue waves. Although afflicted by several technical issues, the data presented here provides a good indication that the probability of occurrence of plunging waves should be better incorporated into the design of offshore structures, particularly the ones that aim to harvest energy in offshore environments.

In this work, we propose simple and robust technique for the retrieval of underlying surface spectral albedo using spaceborne observations. It can be used to process both multispectral moderate resolution satellite data and also multi - zone high spatial resolution data. The technique can work automatically for different types of land surfaces without using huge databases accumulated in advance. The new cloud discrimination and retrieval of the water vapor content in atmosphere procedures are presented. The key point of the proposed atmospheric correction technique is the suggested single-wavelength method for determining the atmospheric aerosol optical thickness without reference to a specific type of underlying surface spectrum. The retrievals of spectral albedo for various land surfaces with developed technique, performed using computer simulation and experimental data, have demonstrated a high retrieval accuracy.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

The extracts from the aerial parts of Helianthus salicifolius A. Dietr and Helianthus tuberosus L. collected in June were obtained using carbon dioxide supercritical fluid extraction with water as co-solvent. The antimicrobial activity in vitro of these extracts were determined against the reference species of Gram-positive and Gram-negative bacteria as well as fungi, representing by the yeast species of Candida spp. The following parameters were estimated: minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC). Both extracts were found to possess antimicrobial activity with MIC = 0.62-5 mg mL-1 for bacteria and MIC = 5-10 mg mL-1 for yeasts, showing bactericidal (MBC/MIC = 2-4) or fungicidal effect (MFC/MIC = 1-2 ). The highest activity was observed against S. aureus ATCC 29213 (MIC = 0.62 mg mL-1 for H. salicifolius extract; MIC = 2.5 mg mL-1 for H. tuberosus extract). Bactericidal effect of both extracts against S. aureus ATCC 29213 was confirmed by time-kill assay. Higher antioxidant activity was found for H. tuberosus extract (EC50 = 0.332 mg mL-1) as compared to that of H. salicifolius (EC50 = 0.609 mg mL-1). The total polyphenol content (TPC) expressed as gallic acid equivalents (GAE) was 13.75 ± 0.50 mg GAE (g of H. salicifolius extract)-1 and 33.06 ± 0.80 mg GAE (g of H. tuberosus extract)-1. There was a correlation between the antioxidant potential of both extracts and TPC but not between antistaphylococcal activity and TPC. The obtained data suggest potential application of these extracts as the natural preparations with the biocidal activity, including those with antistaphylococcal activity. Besides, both extracts may be regarded as potential natural conservants in cosmetics as well as natural preservatives in food.

In the Lower Yarmouk Gorge the chemical composition of regional, fresh to brackish, mostly thermal groundwater reveal a zonation in respect to salinization and geochemical evolution, which is seemingly controlled by the Lower Yarmouk fault (LYF) but does not strictly follow the morphological Yarmouk Gorge. South of LYF the artesian Mukeihbeh well field produces in its central segment groundwaters of almost pure basaltic-rock type with low contribution (<0.3 vol-%) of Tertiary brine, hosted in deep Cretaceous and Jurassic formations. Further distal, the contribution of limestone water increases originating from the Ajloun Mts. North of the LYF, the Mezar wells, the springs of Hammat Gader and Ain Himma produce dominantly limestone water, which contains 0.14-3 vol-% of the Tertiary brine and possess hence variable salinity. The total dissolved equivalents of solutes gained by water/rock interaction (WRI) and mixing with brine, TDE(WRI+brine), amounts to 10-70 % in the region comprising the Mukheibeh field, Ain Himma and Mezar 3 well, to 55-70 % in the springs of Hammat Gader, and to 80-90 % in wells Mezar 1 and 2. The type of salinization indicates that the Lower Yarmouk fault seemingly acts as the divide between the Ajloun and the Golan Heigths dominated groundwater.

Undoubtedly the Wageningen B-screw Series is the most widely used systematic propeller series. It is very popular to preselect propeller dimensions during the preliminary design stage before performing a more thorough optimization, but in the smaller end of the market it is often used to merely select the final propeller. Over time the originally measured data sets were faired and scaled to a uniform Reynolds number of 2·10⁶ to increase the reliability of the series. With the advent of the computer, polynomials for the thrust and torque values were calculated based on the available data sets. The measured data are typically presented in the well-known open-water curves of thrust and torque coefficients K_T and K_Q versus the advance coefficient J. Changing the presentation from these diagrams to efficiency maps reveals some unsuspected and surprising behaviours, such as multiple optima when optimizing for efficiency or even no optimum at all for certain conditions. These artefacts get more pronounced at higher pitch to diameter ratios and low blade numbers. The present work builds upon the paper presented by the author at the AMT’17 and smp’19 conferences and now includes the extended efficiency maps, as suggested by Danckwardt, for all propellers of the Wageningen B-screw Series.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Mediterranean coastal lagoons and their peripheral areas often provide a collection of habitats for many species, and they often face significant threats from anthropogenic activities. Diverse human activities in such areas directly affect the spatio-temporal dynamic of surface water and its ecological characteristics. Monitoring the surface water dynamic, and understanding the impact of human activities are of great significance for coastal lagoon conservation. The Regional Natural Park of Narbonne includes a typical Mediterranean lagoon complex where surface water dynamic and its potential link with local diverse human activities has not yet been studied. In this context, based on all the available Landsat images covering the study area during 2002-2016, this study identified the water and non-water classes for each satellite observation by comparing three widely used water indices (i.e., NDVI, NDWI and MNDWI) and using the Otsu method. The yearly water frequency index was then computed to present the spatio-temporal dynamic of surface water for each year, and three water dynamic scenarios were also identified for each year: permanent water (PW), non-permanent water (NPW) and non-water (NW). The spatial and inter-annual variation in the patterns of the three water scenarios were characterized by computing the landscape metrics at scenario-level quantifying area/edge, shape, aggregation and fragmentation. Finally, the quantitative link between different land use and land cover (LULC) types derived from the LULC maps of 2003, 2012 and 2015 and the surface water dynamic scenarios was established in each of the 300 m x 300 m grid cells covering the study area to determine the potential impact of human activities on the surface water dynamic. In terms of the inter-annual variation during 2002-2016, PW presented an overall stability, and NPW occupied only a small part of the water surface in each year and presented an inter-annual fluctuation. NPW had a smaller patch size, with lower connectivity degree and higher fragmentation degree. In terms of spatial variation during 2002-2016, NPW often occurred around PW, and its configurational features varied from place to place. Moreover, PW mostly corresponded to natural lagoon, and salt marsh (as a part of lagoons), and NPW had a strong link with arable land (agricultural irrigation) and salt marsh (salt production), sand beach/dune, coastal wetlands and lagoon for the LULC maps of 2003, 2012 and 2015. However, more in-depth analysis is required for understanding the impact of sand beach/dune, coastal wetlands and lagoon on surface water dynamics. This study covers the long-term variations of surface water patterns in a Mediterranean lagoon complex having intense and diverse human activities, and the potential link between LULC types and the water dynamic scenarios was investigated on different dates. The results of the study should be useful for environmental management and protection of coastal lagoons.

It is shown that structuring at the microlevel is the intrinsic property of water and aqueous solutions. At room conditions water (including "ultrapure" one) and aqueous solutions are dispersed systems in which microcrystals of NaCl, surrounded by a layer of hydrated water (average diameter - 10-15 microns), are "elementary microparticles", which form the basis of the dispersed phase. Possible ways of formation of these microparticles and their evolution in the process of evaporation of unstructured part of water - dispersion medium - are considered. It is shown, in particular, that they are present in the air as aerosol contaminants. When the ionic strength of the solution increases, the water-salt particles coagulate, forming a new phase - coacervates, remaining on the substrate after evaporation of the liquid part of the water. The aggregates of coacervate structures, formed in a liquid medium, are disordered during heating, which can cause a change in a number of physicochemical properties of water at the temperatures of 50°-60°C range that have not been correctly explained in the framework of atomic-molecular concepts.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

Decision tables have been used for many years in data processing and business applications to simulate complex rule sets. Several computer languages have been developed based on rule systems and they are easily programmed in several current languages. Land management and river-reservoir models simulate complex land management operations and reservoir management in highly regulated river systems. Decision tables are a precise yet compact way to model the rule sets and corresponding actions found in these models. In this study, we discuss the suitability of decision tables to simulate management in the river basin scale Soil and Water Assessment Tool (SWAT+) model. Decision tables are developed to simulate automated irrigation and reservoir releases. A simple auto irrigation application of decision tables was developed using plant water stress as a condition for irrigating corn in Texas. Sensitivity of the water stress trigger and irrigation application amounts were shown on soil moisture and corn yields. In addition, the Grapevine Reservoir near Dallas, Texas was used to illustrate the use of decision tables to simulate reservoir releases. The releases were conditioned on reservoir volumes and flood season. The release rules as implemented by the decision table realistically simulated flood releases as evidenced by a daily NSE (Nash-Sutcliffe Efficiency) of 0.52 and a percent bias of -1.1%. Using decision tables to simulate management in land, river and reservoir models was shown to have several advantages over current approaches including: 1) mature technology with considerable literature and applications, 2) ability to accurately represent complex, real world decision making, 3) code that is efficient, modular and easy to maintain, and 4) tables that are easy to maintain, support, and modify.

In common model testing practise, the measured values of the self propulsion test are split into the characteristics of the hull, the propeller and into the interaction factors. These coefficients are scaled separately to the respective full scale values and subsequently reassembled to give the power prediction. The accuracy of this power prediction depends {\em inter alia} on the accuracy of the measured values and the scaling procedure. An inherent problem of this approach is, that it is virtually impossible to verify each single step, because of the complex nature of the underlying problem. In recent years the scaling of the open-water characteristics of propeller model tests attracted a renewed interest, fuelled by competitive tests, which became the norm due to requests of the customer. This paper will show the influence of different scaling procedures on the predicted power. The prediction is compared to the measured trials data and the quality of the prediction will be judged. The procedures examined are the standard ITTC~1978 procedure plus derivatives of it: the Meyne, the strip method and the βᵢ-method.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Dietary assessment methods recognized as appropriate for the general population are usually applied in a similar manner to athletes, despite knowledge that sport-specific factors can complicate assessment and impact accuracy in unique ways. As dietary assessment methods are used extensively within the field of sports nutrition, there is concern the validity of methodologies have not undergone more rigorous evaluation in this unique population sub-group. The purpose was to systematically review studies comparing two or more methods of dietary assessment, including dietary intake measured against biomarkers or reference measures of energy expenditure, in athletes. Six electronic databases were searched for English-language, full-text articles published from January 1980 until June 2016. The search strategy combined the following keywords: diet, nutrition assessment, athlete and validity; where the following outcomes are reported but not limited to: energy intake, macro and/or micronutrient intake, food intake, nutritional adequacy, diet quality, or nutritional status. Meta-analysis was performed on studies with sufficient methodological similarity, with between-group standardized mean differences (or effect size) and 95 % confidence intervals (CI) calculated. Of the 1624 studies identified, 18 were eligible for inclusion. Studies comparing self-reported energy intake (EI) to energy expenditure assessed via doubly labelled water were grouped for comparison (n=11) and demonstrated mean EI was under-estimated by 19 % (- 2793 ± 1134 kJ/d). Meta-analysis revealed a large pooled effect size of - 1.006 (95% CI: -1.3 to -0.7; p<0.001). The remaining studies (n=7) compared a new dietary tool or instrument to a reference method(s) (e.g. food record, 24-h dietary recall, biomarker) as part of a validation study. This systematic review revealed there are limited robust studies evaluating dietary assessment methods in athletes. Existing literature demonstrates substantial variability between methods, with under and misreporting of intake frequently observed. There is a clear need for careful validation of dietary assessment methods, including emerging technical innovations, among athlete populations.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

To better understand farmers’ refusal and corresponding negative emotions to pay agricultural water fee under current policy in rural China, this paper applies mental accounting, a behavioral economics framework, to explore how the governmental policies of reform of rural taxes and fees, direct agricultural subsidy programs and agricultural water fee individually influence farmers’ decisions in paying agricultural water fee. Using fieldwork data from 577 farmers and 20 water managers in Sichuan, we explore farmers’ information processing regarding paying agricultural water fee via three sequential mental accounting processes, with the associated underlying principles and measures behind each process. We find that the information processing in three mental accounting scenarios related to the agricultural water fee elucidates farmers’ observed behaviors in rural China. Generally, in the three mental accounting scenarios, two conditional intuitive expectations and nine conditional intuitive preferences are formed, however, the conditions of those expectations or preferences cannot be matched with the facts due to the reform of rural taxes and fees, the direct agricultural subsidy programs and the internal attributes of agricultural water fee, which interpret those negative behaviors in rural China. Additionally, this paper offers a view into how previous policies create negative psychological externalities (such as farmers’ psychological dependence on the government) through mental accounting to negatively influence agents’ subsequent decision making; it highlights the significance of underlying mental factors and information processing of negative behaviors in policymaking for managing or conserving common pool resources.