This paper studied the combined influences of the hot streak and swirl on the cooling performances of the NASA C3X guide vane coated with or without TBCs. The results show that: (1) Even under uniform velocity inlet conditions, the hot streak core can be stretched as it impinges the leading edge which causes higher heat load on the suction side of the forward portion. (2) The swirl significantly affects circumferential and radial migration of the hot streak core in the NGV passage. On the passage inlet plane, positive swirl leads to a hotter tip region on the suction side. In comparison, negative swirl leads to a hotter hub region on the pressure side. (3) Under the influence of swirl, migration of coolant improve the coverage of film cooling close to the midspan, while in the regions close to the hub and tip end-wall, the overall cooling performance decrease simultaneously. (4) In the regions with enough internal cooling, the cooling effectiveness increment is always larger than that in other regions. Besides, the overall cooling effectiveness increment decreases on the region covered by film cooling for the coated vane, especially in the region with negative local heat flux.

One of essential procedure nowadays to analyze a dynamic process in Science and Engineering is Computational modeling. Most of dynamic processes are distributed parameter systems, i.e., systems with state variables depend on the number of independent variables (such as space and time) which are expressed by a set of Partial Differential Equations (PDEs). Lateral method of lines is a method which used for solving PDEs numerically by solving a set of boundary value problems sequentially. The aim is to report the development of PDE toolbox based on SCILAB. This paper provides users with a method that is very easy to understand in the applications related to dynamic process. The method uses a SCILAB template to develop numerical simulations in the new field. In this paper, a model of tropical fruit heat treatment for decimating insect is presented. The illustration will be given to show how the lateral method of line template works to solve the problem.

Cylindrical Fe-6.5wt.% Si bars with 7.5 mm in diameter were successfully fabricated from as cast ingot through three rolling stages within 10 passes: rough rolling at 850–900 °C and 8–10 m/min, medium rolling at 800–850 °C and 10–15 m/min, and finish rolling at 800–850 °C and 12–18 m/min. The evolution of microstructure, texture and ordered structure, and the mechanical property are investigated. The results showed that the grains were refined by the hot bar rolling. Area fractions of the {100}<011> oriented grains and the {011}<100> oriented grains decreased to 0 during the hot bar rolling. Whereas, the {100}<001> component, the {011}<211> component and the {112}<110> component increased, and γ fiber with {111}<110> component was dominant. DO₃ ordered phase were suppressed, and B2 ordered domains were refined after the hot bar rolling. Ductility of the as rolled bar was higher than that of the rotary swaged bar, due to the absence of the DO₃ ordered phase and the fine grains in the rolled bar. Hence, the hot bar rolling technology is an excellent process to fabricate the Fe-6.5wt.% Si bars.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Abstract: Objective: To assess both individual and interactive effects of prenatal medical conditions depression and Diabetes, and health behaviors including smoking during pregnancy on infant birth defects. Methods: The data for this research study were collected by the Pregnancy Risk Assessment Monitoring System (PRAMS) in 2018. Birth certificate records were used in each participating jurisdiction to select a sample representative of all women who delivered a live-born infant. Complex sampling weights were used to analyze the data with a weighted sample size of 4,536,867. Descriptive statistics were performed to explore frequencies of the independent and dependent variables. Bivariate and multivariable analyses were conducted to examine associations among the independent and dependent variables. Results: The results indicate and significant interaction between the variables smoking and Depression and Depression and Diabetes (OR= 3.17; p-value <0.001 and OR= 3.13; p-value <0.001 respectively). Depression during pregnancy was found to be strongly associated with delivering an infant with a birth defect (OR= 1.31, P-value < 0.001). Conclusion: Depression during pregnancy and its interaction with smoking and Diabetes are vital in determining birth defects in infants. The results indicate that birth defects in the United States can be lowering Depression in pregnant women.

While SARS-CoV-2 uses angiotensin converting enzyme 2 (ACE2) as the receptor for cell entry, it is important to examine for other potential interactions between the virus and other cell receptors. Based on the clinical observation of low smoking prevalence among hospitalized COVID-19 patients, we recently identified a “toxin-like” amino acid (aa) sequence on the receptor binding domain of the spike glycoprotein of SARS-CoV-2 (aa 375-390) with homology to a sequence of a snake venom toxin, which could interact with nicotinic acetylcholine receptors (nAChRs). We now present computational molecular modelling and docking experiments using 3D structures of the SARS-CoV-2 spike glycoprotein and the extracellular domain of the nAChR alpha9 subunit. We identified an interaction between the aa381-386 of the SARS-CoV-2 spike glycoprotein and the aa189-192 of the extracellular domain of the nAChR alpha9 subunit, a region which forms the core of the “toxin-binding site” of the nAChRs. The mode of interaction is very similar to the interaction between the alpha9 nAChR and alpha-bungarotoxin. A similar interaction was observed between the pentameric alpha7 AChR and the SARS-CoV-2 spike glycoprotein. Our findings support the hypothesis that severe COVID-19 may be associated with disruption of the nicotinic cholinergic system which could be caused by an interaction between SARS-CoV-2 and nAChRs.

One of the main factors that influence the fertility of cattle in grazing systems in hot tropical climates is heat stress. The objective of this study was to evaluate the effect of season, breed, hormonal and physiological condition on the quantity and quality of cumulus-oocyte complexes (COCs) and embryos produced in vitro, from Romosinuano (RM) and Tropical Milking (TM) donors. Three ovum pick-up and in vitro fertilization (OPU-IVF) were performed, one per season; hot dry (HD; 10, 10), hot humid (HH; 9, 9) and fresh dry (FD; 7, 10) in RM and LT donors. Serum levels of cortisol, insulin and glucose were measured, in addition to heart rate (HR), respiratory rate (RR) and rectal temperature (RT). Effect of season x genotype interaction (p≤0.05) was observed in all COCs variables and only in cleavage embryos (CLI) (p≤0.05). Body weight (BW) affected all COCs variables (p≤0.01), except unviable (UNV) although affected degenerated embryos (DEG) (p≤0.01) and total blastocysts (BLAST) (p≤0.01). Cow age only affected viable COCs (VIAB) (p ≤ 0.05), code one blastocysts (BC1) and BLAST (p≤0.01). Cortisol affected total COCs (COCsT), VIAB and total matured in vitro (TMIV) (p≤0.01), as well as CLI, BC1 (p≤0.01) and BLAST (p≤0.05). Insulin affected COCsT (p≤0.01), UNV (p≤0.05), denuded oocytes (DE) (p≤0.01), BC1 and code two blastocysts (BC2) (p≤0.01). Glucose affected all COCs variables (p≤0.01), except UNV and all embryo variables except BC2. HR affected COCsT, DE, TMIV (p≤0.01), CLI, BLAST and DEG (p≤0.05). RR affected COCsT, UNV, VIAB, CLI (p≤0.05), BC1, BLAST and DEG (p≤0.01). RT only affected DE, VIAB (p≤0.01) and BLAST (p≤0.05). The seasonal climatic year variation of Veracruz and changes in physiological and hormonal variables have diverse effects on the cumulus-oocyte complexes and embryos produced by RM and TM donors.

In this study, the effect of laser processing (LP) on the thermoelectric (TE) properties of bismuth antimony telluride (BST) alloy pellets is investigated. The stoichiometric alloy used is Bi0.4Sb1.6Te3.0, which was prepared by mechanical alloying techniques (MA) and hot pressed (HP) into pellets under optimal pressing and temperature conditions. An innovative approach to HP was also developed to enhance the yield of BST samples per HP process while maintaining the TE profiles of the samples within a variance of less than 1%. The LP process was executed by employing a metal 3D printer, with a thorough analysis of beam parameters. Notably, the laser power (P) was held constant at 25 W, along with a fixed hatching distance (HD) of 50 μm, while the parameter adjusted was the laser's scanning speed (SS), which spanned from [600 - 1800] mm/s in increments of 200 mm/s. Examination via scanning electron microscopy (SEM) revealed two material states: melted and sintered. The melted state formed the surface crust of "canyon" patterns that were held on the surface of the samples, and which both size and quantity were altered with changes in SS. For thermoelectric characterization, two distinct shapes of LP samples were produced: rectangular (for electrical properties) and disk (for thermal properties). The results demonstrated that the electrical properties are profoundly influenced by SS, with the electrical conductivity peak at SS value of 1600 mm/s, while the Seebeck coefficient reaches a minimum at the same value. Consequently, within the temperature range of interest, a notable 12% increase in electrical conductivity and a 9% decrease in the Seebeck coefficient were observed compared to the non-LP material state. Overall, the ZT value experience an 6.9% decline within the same temperature interval.

Since decades, oxybutynin hydrochloride is prescribed to improve bladder control in cases of incontinence and excessive urination frequency. This review summarizes synthetic methods enabling preparation of the racemic drug and, in a detailed manner, preparation of (S)-2-cyclohexyl-2-hydroxy-2-phenylacetic acid, a key intermediate in the synthesis of (S)-oxybutynin. Mode of action and metabolism are briefly commented in order to explain the main adverse effects associated with its use and to justify the evolution observed in the diverse commercial formulations. Repositioning opportunities are discussed in terms of clinical trials for the management of hyperhidrosis, hot flashes, and obstructive sleep apnea.

Cancer is considered nowadays one of the main causes of human death worldwide, being characterized by an alteration of the oxidative metabolism. Many natural compounds with anti-tumor attributes have been described, many of them from plant origin. Among them, capsaicin, which is the molecule responsible for the pungency in hot pepper fruits, has been reported to show antioxidant, anti-inflammatory and analgesic activities, as well as anti-proliferative properties against cancer. Thus, in this work the potential anti-proliferative activity of pepper (Capsicum annuum L.) fruits from diverse varieties with different capsaicin content (California < Piquillo < Padrón < Alegría riojana) against several tumor cell lines (lung, melanoma, hepatoma, colon, breast, pancreas, and prostate) has been investigated. The results showed that the capsaicin content in pepper fruits did not correspond with their anti-proliferative activity against tumor cell lines. By contrast, the greatest activity was promoted by the pepper tissues which contained the lowest capsaicin amount. This indicates that other compounds different from capsaicin have this anti-tumor potentiality in pepper fruits. Based on this, green fruits from the variety Alegría riojana, which has negligible capsaicin levels, was used to study the effect on the oxidative and redox metabolism of tumor cell lines from liver (Hep-G2) and pancreas (MIA PaCa-2). Different parameters from both lines treated with pepper fruit crude extracts were determined including, among others, protein nitration and protein S-nitrosation (two post-translational modifications (PTMs) promoted by nitric oxide), the antioxidant capacity, as well as the activity of the antioxidant enzymes superoxide dismutase (SOD), catalase, and glutathione peroxidase (GPX). Besides, the activity of the NADPH-generating enzymes glucose-6-phosphate dehydrogenase (G6PDH), 6-phosphogluconate dehydrogenase (6PGDH), and NADP-isocitrate dehydrogenase (NADP-ICDH) was followed. Our data revealed that the treatment of both cell lines with pepper fruit extracts altered their antioxidant capacity, enhanced the catalase activity, and considerably reduced the activity of the NADPH-generating enzymes. As a consequence, less H2O2 and NADPH seem to be available to cells, thus avoiding cell proliferation and possibly triggering cell death in both cell lines.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

In the present study Aprepitant (APT) ternary solid dispersions (SDs) were developed and evaluated for the first time. Specifically, ternary SDs of APT with Poloxamer 188 and Soluplus^® (SOL) were prepared via melt mixing and compared to binary APT/Poloxamer 188 and APT/SOL SDs. Initially, combined thermo-gravimetric and hot-stage polarized light microscopy studies indicated that all tested compounds were thermally stable up to 280 °C, while Poloxamer 188 acted as a plasticizer to SOL by significantly reducing the temperature required to fully solubilize the API during SD preparation. Differential scanning calorimetry combined with wide angle X-ray diffraction studies showed that crystalline API was dispersed in both binary and ternary SDs, while Fourier transformation-infrared spectroscopy studies revealed no molecular interactions among the components. Scanning electron microscopy combined with EDAX element analysis showed that the API was dispersed in nano-scale within the polymer matrices, while increasing APT content led to increasing API nano-crystals within the SDs. Finally, dissolution studies showed that the prepared formulations enhanced dissolution of Aprepitant and its mechanism analysis was further studied. A mathematical model was also investigated to evaluate the drug release mechanism

The flow behavior of Fe-6.5wt.%Si alloys during hot compression was investigated at temperatures 650–950 °C and strain rates 0.01–10 s^-1. The results showed that the flow stress depended distinctly on the deformation temperatures and strain rates. The flow stress and work hardening rate increased with the decrease of temperature and the increase of strain rate. The activation energy under all the deformation conditions was calculated to be 410 kJ/mol. The constitutive equation with hyperbolic sine function and Zener–Hollomon parameter was developed. The peak stress, critical stress, and steady-state stress could be represented as σ=A+Bln(Z/A). Dynamic recrystallization occurred under the deformation conditions where the values of Z were lower than 10²⁰. Processing maps were established to optimize the processing parameters. The power dissipation efficiency decreased in the high temperature and low strain rate region, increased in the high temperature and high strain rate region, and remained unchanged in other regions with the increase of true strain. Furthermore, the unstable area expanded. The true strain of 0.7 was the optimum reduction according to the processing map. Based on the analysis of surface quality, microstructures, and ordered structures, the optimized processing parameters for the Fe-6.5wt.%Si alloys were the temperature and strain rate of higher than 900 °C and 0.01–10 s^-1, respectively, or 800–900 °C and lower than 0.4 s^-1, respectively.

Objective: To analyse the association between maternal risk factors such as age, body mass index (BMI) and cigarette smoking, with perinatal outcomes. Materials and Methods: This a retrospective analysis from prospectively collected data performed at Hospital Universitario de Torrejón (Madrid, Spain), between September 2017 and December 2019. All pregnant women with singleton pregnancies and non-malformed live fetuses attending their routine ultrasound examination at 11+0 to 13+6 weeks' gestation were invited to participate. Association between preeclampsia, preterm birth, gestational diabetes mellitus (GDM), small for gestational age (SGA) or fetal growth restricted (FGR) neonates and type of delivery according to maternal age, BMI, and cigarrete smoking was studied. Logistic mixed models were used to analyze the data. Results: 1921 patients were included in the analysis. Women of 40 years old had a significantly higher risk of having GDM (Odds Ratio (OR) 1.61, 95% Confidence Interval (CI) 1.08 to 2.36), and SGA neonates (OR 1.54, 95% CI 1.00 to 2.37). Women with a BMI &lt;18 had an increased rate of birth SGA and FGR neonates (OR 3.28, 95% CI 1.51 to 7.05, and OR 3.73, 95% CI 1.54 to 8.37, respectively), whereas women with a BMI ≥35 had a higher risk of GDM (OR 3.10, 95% CI 1.95 to 4.89). Smoking increased the risk of having SGA and FGR neonates (OR 1.83, 95% CI 1.36 to 2.46, and OR 1.91, 95% CI 1.29 to 2.78). Conclusions: Advanced maternal age, low or high BMI, and smoking status are significant risk factors for pregnancy complications. Both clinicians and society should concentrate their efforts on addressing these factors to enhance reproductive health.

Smoking is a pervasive global health concern associated with a myriad of diseases, but its impact on cellular aging, particularly in relation to telomeres, is increasingly recognized. Telomeres, protective caps at the ends of chromosomes, play a crucial role in maintaining genomic integrity. This review critically examines the existing evidence on the association between smoking and telomere atrophy, exploring the molecular mechanisms involved and the implications for accelerated aging and heightened disease risk. The comprehensive analysis encompasses both cross-sectional and longitudinal studies, elucidating potential gender and age disparities. Insights into the molecular pathways linking smoking to telomere shortening are discussed, along with the broader implications for public health. The review concludes by outlining potential interventions and suggesting future research directions in this critical area.

The present study compared the contralateral suppression and the amplitude of distortion product otoacoutsic emissions (DPOAEs) between smokers and non-smokers to determine the influence of smoking. Thirty smokers and thirty non-smokers within the age range of 18-40 years with a normal hearing sensitivity were considered for the study. For both the groups, DPOAEs were measured and the efferent auditory system functioning was measured by presenting the white noise of 50 dB HL to the contralateral side, while recording the DPOAEs. There was no significant effect of age on the amplitude of DPOAEs in both the groups. However, there were significant differences in the amplitude of DPOAEs between smokers and non-smokers. The amount of suppression and DPOAE amplitude were reduced in smokers when compared to non-smokers. The study found no significant correlation between the amount of smoking and amount of suppression between smokers and non-smokers. However, there were significant correlations between the amount of smoking and DPOAE at low and mid frequencies between smokers and non-smokers. Therefore, the present study highlights the increased damage to the efferent auditory system risk and the smoking ill-effects on the efferent auditory system.

The novel COVID-19 disease is a contagious acute respiratory infectious disease whose causative agent has been demonstrated to be a new virus of the coronavirus family, SARS- CoV-2. Multiple studies have already reported that risk factors for severe disease include older age and the presence of at least one of several underlying health conditions. However, a recent physiopathological report and the French COVID-19 scientific council have postulated a protective effect of tobacco smoking. Thanks to a meta-analysis, we have been able to demonstrate the statistical significance in this regard of twelve series from China, France and in the US, reporting three different smoking status (current smoker,former smoker, with a smoking history) as well as disease severity (with respectively odds-ratio of 1.78 [1.08-3.10], 4.60 [3.13-7.17], 2.74 [0.63-5.89]). Subsequently and using a Bayesian approach we have established that past, and present smoking is associated with more severe COVID-19 outcomes. Finally, we refute claims linking general population smoking status (N=O(10^8) or O(10^9)) to much smaller disease course series (N=O(10^4)). The latter point in particular is presented to stimulate academic discussion, and must be further investigated by well-designed studies.

Almost 6% of cancers worldwide are attributable to alcohol consumption. Approximately half of them occur in tissues highly exposed to ethanol, such as the oral cavity, pharynx, upper larynx and esophagus. However, since ethanol is not mutagenic and the carcinogenic metabolite of ethanol (acetaldehyde) is mainly produced in the liver, it is unclear why alcohol consumption preferentially causes a local carcinogenic effect. We recently hypothesized that the cytotoxic activity of ethanol could explain the high risk of these cancers in alcohol users. Here we report that short-term exposures (2-3 seconds) to ethanol concentrations between 10% and 15% start to cause a marked cytotoxic effect on human epithelial keratinocytes in a concentration-dependent manner. After discussing new evidence that cancer is the end-result of the accumulation of cell divisions in stem cells, we explain why regular alcohol consumption imposes a high risk of cancer on these tissues. Briefly, the cytotoxicity of ethanol reduces the lifespan of the cells lining these tissues. The stem cells located in deeper layers need to divide more often than usual to renew the damaged epithelia. The accumulation of cell divisions in stem cells leads to the accumulation of cancer-promoting errors (e.g., mutations arising during DNA replication) that increase their risk of malignant transformation. Cell division also exposes the DNA of the stem cells to the genotoxic activity of acetaldehyde and tobacco carcinogens. We propose that choosing alcoholic beverages containing non-cytotoxic concentrations of ethanol, or diluting ethanol to non-cytotoxic concentrations, is a simple way to reduce the risk of cancer of the oral cavity, pharynx, larynx and esophagus in alcohol users. This preventive strategy may also abolish the known synergistic effect of alcohol drinking and tobacco smoking on the risk of these cancers.

Artificial intelligence methods, especially artificial neural networks (ANNs), have increasingly been utilized for the mathematical description of physical phenomena in (metallic) material processing. Traditional methods often fall short in explaining the complex, real-world data ob-served in production. While ANN models, typically functioning as "black boxes," improve pro-duction efficiency, a deeper understanding of the phenomena, akin to that provided by explicit mathematical formulas, could enhance this efficiency further. This article proposes a general framework that leverages (CAE) ANNs to explain predicted results alongside their graphical presentation, marking a significant improvement over previous approaches and those relied on expert assessments. Unlike existing Explainable AI (XAI) methods, the proposed framework mimics the standard scientific methodology, utilizing minimal parameters for the mathematical representation of physical phenomena and their derivatives. Additionally, it analyzes the relia-bility and accuracy of the predictions using well-known statistical metrics, transitioning from deterministic to probabilistic descriptions for better handling of real-world phenomena. The proposed approach addresses both aleatory and epistemic uncertainties inherent in the data. The concept is demonstrated through the hot extrusion of aluminum alloy 6082, where CAE ANN models and predicts key parameters, and ChatGPT explains the results, enabling researchers and/or engineers to better understand the phenomena and outcomes obtained by ANNs.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Hypertension (HTN) is the foremost contributor to cardiovascular diseases (CVD), which remain a leading cause of death. However, adherence to the properly prescribed dosage form is critical and challenging for patients with chronic diseases such as HTN to prevent illness progression and death. The study’s objective was to develop AMB-loaded subcutaneous implants to reduce the frequency of administration, thus improving patient compliance during HTN management. AMB subcutaneous implants were prepared using continuous hot melt extrusion technology using PCL and PLGA with dimensions of 7.5 cm (length) by 2 mm (diameter). The implants were characterized for thermal characteristics, drug-excipient incompatibilities, surface morphology, fracturability, in vitro release, and stability studies. DSC showed that the drug was in the crystalline state in the fabricated implants. Scanning Electron Microscopy (SEM) revealed a smooth surface. The lead formulation presented good drug content, showed an extended drug release profile over 30 days, and followed zero-order release kinetics with a mean dissolution time of 15 days. The formulation was stable over 30 days in accelerated stability conditions (the last time point was tested, 40℃/75% RH), and the release profile was similar to the initial drug release profile. The lead formulation showed good fracturability during textural analysis. Therefore, the hot melt extruded implants could be an alternative management strategy for conventional amlodipine besylate (AMB) formulation.

The menopausal transition often accompanies distressing manifestations, including vasomotor symptoms, sleep disruptions, and depressive syndrome. Omega-3 fatty acids have emerged as a potential intervention to alleviate these symptoms. This review aimed to comprehensively assess the impact of omega-3 supplementation on vasomotor symptoms, sleep quality, and depression among postmenopausal women. We conducted a systematic search focusing on randomized control trials across the Cochrane Library, Web of Science, PubMed, CINAHL, EMBASE, and SCOPUS databases from inception to August 2023. Among the initial pool of 163 studies, 9 studies met the inclusion criteria and were incorporated into this review. Four studies suggested potential benefits of omega-3 intake for improving hot flashes and night sweats. Sleep quality outcomes displayed heterogeneity across the studies. Incorporating diverse scales such as the Hamilton Depression Rating Scale-21, the Patient Health Questionnaire depression scale, and Generalized Anxiety Disorder-7 for depression outcomes, the review found inconclusive evidence on omega-3's impact on depression. Overall, the combined analysis of these studies did not provide substantial evidence to support the efficacy of omega-3 fatty acids in improving vasomotor symptoms, sleep quality, and depression. Further well-designed RCTs with larger participant groups are crucial to validate and generalize these results.

Objectives: The present study was conducted to evaluate the indicators of the aging-friendly using GIS software in the eight districts of Ahwaz, southwest Iran in 2022. Materials and methods: this descriptive-analytical study was conducted on 317 older adults by stratified random sampling method. Data collection tools were demographic characteristics and aging-friendly city indicators. GIS methods were used for the spatial analysis and SPSS version 28 software was used to analyze descriptive statistics. Results: The mean age of the participants was 66.21±6.99 years. Most of the participants in this study were male (53.9%), illiterate (34.7%), married (84.9%) and residents of district 7 (22.1%). The findings of the present study showed that all 8 districts follow spatial autocorrelation and cluster pattern in all components of the aging-friendly city (urban open spaces, intra-urban transportation system, public and religious places and buildings, safety and ease of traffic, social participation and communication, social respect, culture-recreation, health and treatment). Conclusion: According to the results, the city of Ahwaz is far from the ideal level among the components of an aging-friendly city; therefore, provincial and city officials should pay more attention to these indicators and take more effective steps to increase their quality.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

This paper presents a novel approach of welding thick steel plates that offers time and energy savings compared with conventional techniques. The combination of gas metal arc welding (GMAW) and hot-wire technology simplifies the joint configuration and enhances the process tolerance. In this study, a square butt joint was prepared with as-cut edges and a thickness of 15 mm. The relationship between the welding current and the deposition rate of solo GMAW showed limitations and low process tolerance. Increasing the welding current led to a larger deposited volume with unnecessary weld penetration. An independent deposition volume due to hot-wire insertion was used to improve process tolerance. This approach provided an additional volume without increasing the welding current and reduced unnecessary penetration. With optimized parameters, full-penetration single-pass welding was achieved. Compared with the formation of a typical single-v butt joint at a similar welding speed of 30 cm/min, the proposed process reduced the minimum arc time and power consumption by approximately 83% and 62%, respectively. Moreover, a single pass at a travel speed of 60 cm/min was achieved with approximately 91% and 81% less arc time and power consumption, respectively. In summary, the combined process simplifies the joint configuration, enables full-penetration single-pass welding, and reduces time and energy requirements.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

. In today’s world, cyber attack is one of the major issues concerning the organizations that deal with technologies like cloud computing, big data, IoT etc. In the area of cyber security, intrusion detection system (IDS) plays a crucial role to identify suspicious activities in the network traffic. Over the past few years, a lot of research has been done in this area but in the current scenario, network attacks are diversifying in both volume and variety. In this regard, this research article proposes a novel IDS where a combination of information gain and decision tree algorithm has been used for the purpose of dimension reduction and classification. For experimental purpose the NSL-KDD dataset has been used. Initially out of 41 features present in the dataset only 5 high information gain valued features are selected for classification purpose. The applicability of the selected features are evaluated through various machine learning based algorithms. The experimental result shows that the decision tree based algorithm records highest recognition accuracy among all the classifiers. Based on the initial classification result a novel methodology based on decision tree has been further developed which is capable of identifying multiple attacks by analyzing the packets of various transactions in real time.

This short note proposes a national Geographic Information System (GIS) - based health infrastructure to deal with epidemics and pandemics. Currently, there is no pan-India health infrastructure available that can compile, update, and report the spread of epidemic diseases. It not only curtails the opportunity of finding the real-time data on the spatial distribution of a disease but prevents one to inquire into the causes of the disease through epidemiological analysis. The proposed infrastructure in this study is a pan-India one and can broadly be divided into two parts, hotspot mapping and accessibility to services. In the first part, hospitals are proposed to act as nodes of data collection, sending data to a national GIS portal. This portal shall have the capabilities of plotting the data using map rendering services such as Google and Bing Maps. This way, hotspots can be visualized in no time, benefitting the government and common citizenry alike. The second part deals with the accessibility of citizenry to a wide range of services, i.e., healthcare services, grocery outlets, emergency services, baby food, and many other essential services of the day to day life. In order to implement this, we propose that the government need to enforce a mandatory submission of locational coordinates of all Goods and Services Tax (GST) enrolled service providers. Once the coordinates are submitted, the government can effectively control the opening and closing of services and inform the citizenry at the same time. The proposed infrastructure is going to help deal with the extraordinary situations during epidemic and pandemics similar to what the world is currently facing in the form of Corona Virus Disease 2019 (COVID-19). Furthermore, the infrastructure can be scaled up or down as per the spread of a disease. The health-GIS platform proposed in this concept paper, shall help India in controlling and managing the epidemic more efficiently.

Hot deformation at elevated temperature is essential to densify the particle reinforced Aluminum matrix composites (AMCs) and improve their performance. However, hot deformation behavior of the AMCs is sensitive to the variation of hot processing parameters. In this paper, optimal processing parameters of the dual-scale SiCp/A356 composites was determined to explore the control strategy of the microstructure. Hot compression tests were conducted at the temperature ranging from 460 to 520℃ under strain rates from 0.01 to 5 s−1. Constitutive equation and processing maps were presented to determine the hot processing parameters. Microstructure evolution of the dual-scale SiCp/A356 composites was analyzed. The strain rate of 0.62 ~ 5s-1 and deformation temperature of 495 ~ 518℃ is suitable for the hot processing. The number of DRX grains in the “safe” domains is larger and the dislocation density is lower compared to those of instability domains. DRX particles mainly occurred around SiC particles. The presence of SiC particles can promote effectively the DRX nucleation, which result in that the dynamic softening mechanism of the dual-scale SiCp/A356 composites is dominated DRX.

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

Mere similar grades of same excipients manufactured by two different manufacturers often differ significantly that they even have an impact on the variations in final product or dosage form. Solid lipids are one of the most available options as matrix former in sustained drug delivery. Due to their chemical and physical complexity, lipids may exhibit a complex behaviour (i.e. melting crystallization and polymorphism). The aim of this study was to evaluate the physical and chemical properties of two Glyceryl Monostearate (GMS) lipids (Geleol from Gattefosse and Capmul GMS 50K from Abitec Corp. USA) and how these properties may affect during melt granulation process for sustained release applications. Thermal processing was applied on GMS samples to understand the polymorphic nature and suitability as meltable binders. Niacin was used as model drug. A thorough evaluation of GMS samples and sustained release tablets was undertaken using analytical techniques such as differential scanning calorimetry (DSC), X-ray diffraction (XRD). Moreover, melt viscosity study assisted to apprehend the behaviour of GMS samples in hot melt extrusion processing. Surface morphology of the drug and extruded granules examined via SEM and AFM revealed high level of surface interaction and dense structure of drug inside lipid matrix. The DSC and XRD study confirmed that Geleol could not withstand the heat treatment applied during thecontinuous melt granulation processing. The shifting of stable β form to an unstable α form in Geleol was detected. In the contrary case, Capmul GMS 50K was able to withstand the heat treatment supported by the applied analytical techniques. Nonetheless,both GMS samples perform differently in final dosage form. This change in stable β form to an unstable α form affected dissolution profiles at 3 months storage in accelerated condition. This study helped to interpret the complex solid-state behaviour of solid lipid extrudates with different compositions, in order to the simply and outline a suitable formulation strategy for the development of lipid-based oral dosage forms.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

NSCLC is a very aggressive solid tumor, with a poor prognosis due to post-surgical recurrence. Analysis of the specific tumor and immune signatures of NSCLC samples is a critical step in prognostic evaluation and management decisions for patients after surgery. Routine histological assay has some limitations. Therefore, new diagnostic tools with the capability to quickly recognize NSCLC subtypes and correctly identify various markers are needed. We developed a technique for ex vivo expansion of cancer and immune cells from surgical tumor and lung tissue samples of patients with NSCLC (adenocarcinomas and squamous cell carcinomas) and their examination on ex vivo cell preparations and, parallelly, on histological sections after Romanovsky–Giemsa and immunofluorescent/immunochemical staining for cancer-specific and immune-related markers. As a result, PD-L1 expression was detected for some patients only by ex vivo analysis. Immune cell profiling in the tumor microenvironment revealed significant differences in the immunological landscapes between the patients’ tumors, with smokers’ macrophages with simultaneous expression of pro- and anti-inflammatory cytokines, neutrophils, and eosinophils being the dominant populations. The proposed ex vivo analysis may be used as an additional diagnostic tool for quick examining cancer and immune cells in whole tumor samples and avoiding false negatives in histological assays.

Opium smoking for long hours and over many years is common in Iran, and the Covid-19 pan-demic and false beliefs about the protective effects of that opium against COVID-19 infection has caused the increasing of opium smoking during the pandemic. The aim of this study was to in-vestigate the relationship between non-ergonomic positions of traditional opium smoking in Iran with the occurrence of neck pain and disability, forward head posture and hyperkyphosis. In this cross-sectional and correlation study 120 people who smoke opium were selected based on the inclusion criteria and were interviewed about their addiction profile and evaluated for the pres-ence of pain and disability in the neck by Maudsley Addiction Profile, Leeds Dependence Ques-tionnaire, the Visual Analog Scale and Neck Disability Index. Also, they were evaluated about forward head posture (FHP) through side view photography and hyperkyphosis (HK) through flexible ruler. Data were analyzed by correlation coefficient tests and stepwise linear regression. There was a significant relation between homelessness, the duration of lifetime opium smoking (months), the duration of daily opium smoking (minutes) and drug dependence severity with the severity of neck pain, neck disability, forward head posture and hyperkyphosis. Homelessness is the strongest predictive variable of the possibility of neck pain and disability, FHP and HK, fol-lowed by ‘‘the number of months of opium smoking’’ and ‘‘the number of minutes of opium smoking in one day’’ respectively. Increasing the duration of sitting in non-ergonomic positions can lead to neck pain and disability, FHP and HK due to their non-neutral posture in opium smokers.

Aim: The main purpose of this feasibility study was to estimate compliance and acceptability rate of a 9-Steps mobile app preparation program. Subsequently, to assess its impact regarding attitudes towards smoking cessation. Methods: The program was only available on versions above iOS 13.3. The ecological study collected user’s data via the app from 04/07/2021 to 28/07/2021. Results: A total of 2331 ecological users completed onboarding; 1926 users (73.9%) completed the step 0 and only 265 users continued in step 1. On average, participants actively engaged with intra-steps activities (85,1%). Most users were highly satisfied at the end of each step. On average 86% found the content of each step comprehensive and relevant. Mann-Whitney tests demonstrated positive changes in attitudes toward smoking cessation on the less confident users: willing (3 to 5, p <.05); confidence (3 to 5, p <.001) and readiness to quit (3 to 5, p <.001). Conclusions: This ecological study corroborates the expected dropout between first use and regular use of health mobile apps. However, engagement and satisfaction rates support the feasibility and acceptability of a 9-step preparation program. Additional research is needed to better understand determinants of regular use of mobile apps and its impact on the target behavior.

Background: The primary objective worldwide during the COVID-19 pandemic has been controlling disease transmission. However, lockdown measures used to mitigate transmission have affected human behavior and altered lifestyles, with a likely impact on chronic non-communicable diseases. More than a year into the pandemic, substantial peer-reviewed literature has emerged on altered lifestyles following the varying lockdown measures imposed globally to control the virus spread. Objective: To explore the impact of lockdown measures on the six lifestyle factors, namely diet, physical activity, sleep, stress, social connectedness, and the use of tobacco, alcohol, or other harmful substances.Methods: We comprehensively searched PubMed and the World Health Organization’s global literature database on COVID-19 and retrieved 649 relevant articles for the narrative review. A critical interpretative synthesis of the articles was performed.Results: Most of the articles included in the review identified the negative effect of lockdown measures on each of the lifestyle factors in many parts of the world. Interestingly, encouraging lifestyle trends were also highlighted in a few articles. Such trends can positively influence the outcome of lifestyle-related chronic diseases, such as obesity and diabetes.Conclusions: The COVID-19 pandemic provides an opportunity to better understand the negative impact of strict lockdown measures on lifestyles. At the same time, it helps us identify and initiate positive behavioral changes, which, if consolidated, could improve chronic disease outcomes. It is up to governments, communities, and healthcare/academic entities to derive benefit from lessons learned from the pandemic, with the ultimate objective of better educating and promoting healthy lifestyles among communities.

The COVID-19 pandemic has become a public health emergency of international concern, which may affect lifestyle habits and mental health. Based on national health profile assessments, this study investigates perceived changes of lifestyle habits in response to the COVID-19 pandemic and associations between perceived lifestyle changes and mental health in Swedish working adults. Among 5,599 individuals (50% women, 46.3 years), the majority reported no change (sitting 77%, daily physical activity 71%, exercise 69%, diet 87%, alcohol 90%, and smoking 97%) due to the pandemic. Changes were more pronounced during the first wave (April-June) compared to the second (October-December). Women, individuals <60 years, having a university degree, being white-collar workers and having unhealthy lifestyle habits at baseline had higher odds of changing lifestyle habits compared to their counterparts. Negative changes in lifestyle habits as well as more time in mentally passive sitting at home was associated with higher odds of mental ill-health (including health anxiety regarding one’s own and relatives’ health, generalized anxiety and depression symptoms, and concerns regarding employment and economy). The results em-phasize the need to support healthy lifestyle habits to strengthen the resilience in vulnerable groups of individuals to future viral pandemics, and prevent health inequalities in society.

The current scenario of radioactive waste management requires innovative and automated solutions to ensure effectiveness and safety. In response to this need, the PI3SO (Proximity Imaging System for Sort and Segregate Operations) project was proposed. It is a gamma radiation proximity scanner system for radioactive waste with the primary goal of speeding up some aspects of the waste management cycle while reducing direct human operations. The system will provide proximity imaging for hot spot finding and spectral analysis for radiological characterization, enabling semiautomatic recognition, sorting and separation of radioactive waste. The core of the proposed scanning system consists of an array of 128 CsI(Tl) scintillators, 1 cm3 size, coupled with silicon photomultipliers (SiPM), installed on a motorized bridge sliding along a suitable table in order to scan the materials under investigation.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

Forestry workers play a crucial role in implementing forest management programs, but their outdoor work exposes them to rising temperatures caused by global climate change, which poses potential health risks related to heat. This study focuses on Indonesian forestry workers and examines the relationship between their knowledge of heat-related issues, risk perception, and precautionary behavior in dealing with increasing workplace heat exposure. Developing effective precautionary behavior is essential for preventing heat-related health disorders and promoting health protection programs. To facilitate a comprehensive comparison of the three variables, interviews were conducted with two groups of outdoor workers, comprising 210 forestry workers and 215 paddy farmers. The findings indicate that increasing knowledge about heat-related issues promotes precautionary behavior, and risk perception acts as a mediator between knowledge and behavior. Additionally, the study highlights that the emotion of "dread" intensifies perceived risk and predicts positive behavior change. To enhance heat-related knowledge, exploring the potential use of a "fear" tone is important. In conclusion, comprehensive strategies need to be implemented to promote precautionary behavior among vulnerable forestry workers, particularly manual laborers.

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

Background: The new media provides a convenient digital platform to access, use and exchange health information. As a special group of health care, maternal is still of international concern due to their high mortality rate. Improving maternal health as a Millennium Development Goal of the United Nations is an important quest for the health care system. Scientific research provides advice on how to improve maternal health through stringent reasoning and accurate data. However, the dramatic increase of publications, the diversity of themes, and the dispersion of researchers may reduce efficiency. Objective: This study aims to analyze the research progress on maternal health under the global new media environment, exploring the current research hotspots and research frontiers. Methods: A scientometric analysis was carried out by CiteSpace5.7.R1, searching in the core database of Web of Science for articles published in English from 1998 to 2021, and combined topic words such as new media, maternal, and health. In total, 3312 articles have been retrieved, of which 2270 studies have been included for further analysis. Top countries and institutions, potentially high-impact literature, research frontiers, and hotspots were analyzed in this study. Results: The number of publications grew rapidly after 2008, from 29 publications sharply increasing to 472 publications by 2020. Research centers concentrated in Latin America, such as the University of Toronto, the University of California. The work of Larsson M, Lagan BM, Tiedje L, and Helle C had a high potential impact. Most of the research subjects were maternal and newborn babies, and the research frontiers focused on health education and maternal psychological problems. Maternal mental health, maternal and infant nutrition, weight, production technology, and equipment were hotspots. Conclusion: The development of new media has brought a new era for maternal health, characterized by psychological qualities, healthy and reasonable physical conditions, and advanced technology.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Cyber security plays an important role to protect our computer, network, program and data from unauthorized access. Intrusion detection system (IDS) and intrusion prevention system (IPS) are two main categories of cyber security, designed to identify any suspicious activities present in inbound and outbound network packets and restrict the suspicious incident. Deep neural network plays a significant role in the construction of IDS and IPS. This paper highlights a novel IDS using optimized convolution neural network (CNN-IDS). An optimized CNNIDS model is an improvement over CNN which selects the best weighted model by considering the loss in every epoch. All the experiments have been conducted on the well known NSL-KDD dataset. Information gain has been used for dimensionality reduction. The accuracy of the proposed model is evaluated through optimized CNN for both binary and multiclass categories. Finally, a critical comparison has been performed with other general classifiers like J48, Naive Bayes, NB tree, Random forest, Multilayer Perceptron (MLP), Support Vector Machine (SVM), Recurrent Neural Network (RNN) and Convolution Neural Network(CNN). All the experimental results demonstrate that the optimized CNN-IDS model records the best recognition rate with minimum model construction time.

The spike protein of SARS coronavirus (SARS-CoV) attaches the virus to its cellular receptor, angiotensin-converting enzyme 2 (ACE2), which is mediated by the receptor binding domain (RBD) of the spike protein. Recently, an analysis based on decade-long structural studies of SARS was reported to illustrate with atomic-level details receptor recognition by the novel coronavirus from Wuhan, i.e., 2019-nCoV. Here, this article reports a comprehensive set of structural electrostatic analysis of all SARS-CoV spike protein RBD-related structures as of February 13, 2020, aiming at identifying the electrostatic hot spots for SARS-CoV spike protein to be complexed with ACE2 and its neutralizing antibodies. First, this article identified a structural action mechanism of the F26G19 antibody (of SARS-CoV spike protein), where its Asp56 residue binds to the Arg426 of the SARS-CoV spike protein RBD against the formation of the interfacial Arg426-Glu329 salt bridges between ACE2 and the SARS-CoV spike protein RBD. Second, a hypothesis is reported that a pair of electrostatic clips exist at the interface between ACE2 and the SARS-CoV spike protein RBD, including both Arg426-Glu329 and His445-Glu23-Lys447 salt bridges. Last, this article reports a structurally identified interfacial Glu35-Arg479 salt bridge which helps stabilize the complex structure of ACE2 and the SARS-CoV spike protein RBD. Overall, the structurally identified electrostatic hot spots reported here may be useful for the design of SARS-CoV-neutralizing antibodies in future.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

The ITALUNG trial started in 2004 and compared lung cancer (LC) and other-causes mortality in 55-69 years-aged smokers and ex-smokers who were randomized to four annual chest low-dose CT (LDCT) or usual care. ITALUNG showed a lower LC and cardiovascular mortality in the screened subjects after 13 years of follow-up, especially in women, and produced many ancillary studies. They included recruitment results of a population-based mimicking approach, development of software for computer aided diagnosis (CAD) and lung nodules volumetry, LDCT assessment of pulmonary emphysema and coronary artery calcifications (CAC) and their relevance to long-term mortality, results of a smoking-cessation intervention, assessment of the radiations dose associated with screening LDCT, and the results of biomarkers assays. Moreover ITALUNG data indicated that screen-detected LCs are mostly already present at baseline LDCT, can present as Lung Cancer associated with Cystic Airspaces, and can be multiple. However, several issues of LC screening are still unaddressed. They include the annual vs biennial pace of LDCT, choice between opportunistic or population-based recruitment and between uni or multi-center screening, implementation of CAD-assisted reading, containment of false positive and negative LDCT results, incorporation of emphysema and CAC quantification in models of personalized LC and mortality risk, validation of ultra-LDCT acquisitions, optimization of the smoking-cessation intervention and prospective validation of the biomarkers.

Smoking is a major risk factor for non-communicable diseases and remains a significant public health challenge in many lower- and middle-income countries (LMIC) including Namibia. The purpose of the study was to estimate the prevalence of smoking and its associated risk factors among HCWs and non-HCWs in Zambezi region. An exploratory cross-sectional survey was conducted between March and October 2020 among residents of the eight (8) constituencies of Zambezi region. Four hundred and sixty-one (461) respondents who had been residents of the selected constituencies for over five years and aged between 17-60 years were selected for the study. The main outcome measure was current cigarette smoking status. Descriptive statistics were used to summarize the socio-demographic characteristics of the respondents. We stratified data analysis by individual being health workers or non-health workers. A bivariate Pearson Chi-square test was used to determine the association between socio-demographic characteristics and the smoking status. Statistically significant variables in the bivariate analysis were used as predictors in the univariate and multivariate models. The response rate of potential participants was 95% (n=434). The mean (±SD) age of participant’s was 32.5 (± 11.34 years). Significant relationships were observed between smoking status and area of residency (constituency), gender, age category, level of education, age of onset of smoking and the daily smoking frequency. The majority of smokers (n=108) were none-HCWs with males being the majority (n=62). Age (p=0.001), education levels (p=0.001) and area of residency (p=0.022) were highly associated with smoking among none-HCW while marital status was associated with smoking among HCWs (p=0.013). In the final multivariate model, the odds of smoking among female non-HCWs were significantly lower (OR: 0.386; 95% CI: 0.228 – 0.655). Furthermore, the odds of smoking among this same group were lower among those who had secondary level education (OR: 0.178; 95% CI: 0.0659 – 0.483), post-secondary (OR: 0.117, 95% CI: 0.0412 – 0.330) and first stage tertiary (OR: 0.306: 95% CI: 0.106 – 0.881) compared to those who had primary school education. In conclusion, smoking prevalence among none HCWs and HCWs working in Zambezi included in the study was similar to that of the general Namibian population but higher than other neighboring countries within SADC. The results showed a need for the establishment of specific smoking related strategies that target HCWs to address smoking use parallel to the running of none HCWs which would ultimately decrease the smoking prevalence and improve health.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

The prolonged exposure to nicotine and the development of nicotine dependence have significant implications for cancer risk. Tobacco use, driven by nicotine addiction, is a major contributing factor to the development of various types of cancer. Smoking tobacco, in particular, has been strongly associated with an increased risk of lung cancer, as well as other malignancies. The harmful chemicals present in tobacco products, including carcinogens, can cause DNA damage and promote the initiation and progression of cancerous cells. This article presents a comprehensive literature review on the neurobiology of nicotine dependence and its implications for tobacco use treatment. Nicotine dependence is a complex phenomenon involving various neurobiological mechanisms. When nicotine enters the body, it binds to nicotinic acetylcholine receptors in the brain's reward circuitry, triggering the release of neurotransmitters like dopamine, serotonin, and norepinephrine. Over time, repeated nicotine exposure leads to neuroadaptive changes in the brain, resulting in increased motivation to seek and use the drug. Understanding the neurobiology of nicotine dependence is crucial for developing effective treatment strategies. Pharmacological interventions, such as nicotine replacement therapy and medications like bupropion and varenicline, can help individuals manage cravings and withdrawal symptoms. Additionally, behavioral therapies and counseling play a vital role in enhancing self-efficacy and providing support for smoking cessation efforts. By reviewing the existing literature, this article sheds light on the intricate neural pathways and processes involved in nicotine addiction. It emphasizes the importance of a multidimensional approach that combines pharmacological treatments and behavioral interventions to address the physiological and psychological aspects of nicotine dependence. This knowledge can inform the development of more targeted and personalized treatment approaches to help individuals overcome tobacco addiction and improve their chances of successful smoking cessation.

The current spreading novel coronavirus SARS-CoV-2 is highly infectious and pathogenic and has attracted global attention. Recent studies have found that SARS-CoV-2 and SARS-CoV share around 80% of homology and use the same cell entry receptor, ACE2. These inspired us to study other receptors of SARS-CoV, which may be used for SARS-CoV-2 binding as well. In this study, we screened the gene expression of three receptors (ACE2, DC-SIGN and L-SIGN) in four datasets of normal lung tissue from lung adenocarcinoma patients and two single-cell RNA sequencing datasets from normal lung and bronchial epithelial cells separately. No significant difference in gene expression of these three receptors were found between gender groups (male vs female). We found higher gene expression of DC-SIGN in elder with age>60 and higher gene expression of L-SIGN in Caucasian than Asian. Similar to ACE2, we observed significantly higher DC-SIGN gene expression in the lungs of smokers, especially former smokers. However, smokers upregulate ACE2 and DC-SIGN gene expression in different cell types. In the whole lung, ACE2 is actively expressed in remodeled Alveolar Type II cells of former smokers, while DC-SIGN is largely expressed in monocytes of former smokers and dendritic cells of current smokers. In bronchial epithelium, no obvious gene expression of DC-SIGN and L-SIGN was observed while ACE2 was found to be actively expressed in goblet cells of current smokers and club cells of non-smokers. In conclusion, our findings may indicate that smokers, especially former smokers, and people over 60 have higher risk and are more susceptible to SARS-CoV-2 infection. Also, this study provides hints on possible SARS-CoV-2 pathogenicity mechanisms in lung infection.

Healthy life style is associated with decreased risk of chronic kidney disease (CKD) and mortality in the general population. However, there is no definitive evidence on the benefits of physical activity and other health-related behaviors in the early-stage CKD. This study aimed to explore the association between health-related behaviors and end-stage renal disease (ESRD) and mortality in the early stages of CKD. The National Health Insurance Service (NHIS) database from January 1st, 2009 to December 31st, 2016 was used to screen 83,470 subjects with early stage CKD. Cox proportional hazard regression analysis was used to evaluate the association between health-related behaviors and ESRD and death. Kaplan-Meier curves for mortality and ESRD were plotted according to the physical activity, smoking status and alcohol consumption pattern. Risk of death decreased significantly in subjects who engaged in sufficient physical activity (adjusted Hazard Ratio (HR) 0.73; 95% CI: 0.64-0.83; p < 0.001). Risk of ESRD and death increased significantly in the current smoker with adjusted HR of 1.44 (95% CI: 1.06-1.95; p < 0.02) and 1.61 (95% CI: 1.44-1.80; p < 0.001) respectively. Therefore, systematic interventions to encourage physical activity and smoking cessation need to be actively considered in the early stages of CKD.

This contribution deals with the assessment of air pollution caused by atmospheric aerosol particulate matter fraction PM10 and benzo[a]pyrene (BaP) in the urban agglomeration of Ostrava, located in the Czech Republic in Central Europe. The motivation for this research was the need to identify the sources of air pollution in the area, particularly in locations where the contribution of different sources to concentrations of pollutants of concern has not been elucidated yet. In this study, source apportionment in the vicinity of the industrial hot-spot was performed by statistically evaluating measured pollutant concentrations as a function of meteorological variables and using the Positive Matrix Factorization (PMF) receptor model. A significant methodological innovation and improvement over previous assessments was the higher monitoring resolution of benzo[a]pyrene, with samples collected at three-hour intervals instead of the standard 24-hour collection period. The key findings indicate that in the cold part of the year, secondary particles - specifically sulphates and ammonium nitrates - were responsible for the most significant portion of PM10 air pollution throughout the area of interest. The contribution of these particles ranged from one third to two fifths of the total concentration, except at the industrial site of Ostrava-Radvanice (TORE), where they accounted for approximately one fifth of the measured pollution concentration level. Emissions from individual household heating were identified as the main source of this type of pollution. With regards to benzo[a]pyrene air pollution, the study found that in the whole area of interest, except for the Ostrava-Radvanice site, it mainly originated from individual heating with coal (90%). In contrast, at the Ostrava-Radvanice site, two-thirds of the benzo[a]pyrene pollution came from the premises of Liberty Ostrava a.s., primarily from coke production, and less than one-third from local domestic heating. This study also determined the spatial extent of the occurrence of extremely high benzo[a]pyrene concentrations (above 5 ng/m3), which are estimated to affect nearly 10,000 inhabitants. The results confirm that the data from the TORE station are only representative of its immediate surroundings and are not applicable to the assessment of air quality and causes of air pollution in the whole city of Ostrava or the urban area of Ostrava-Radvanice as a whole. After years of research, these findings provide the Ministry of the Environment of the Czech Republic and the government with an accurate basis for implementing measures to address the identified pollution sources in the area of interest. The success of this study was made possible by the adoption of a more detailed sampling approach, which involved a resolution of 3 hours instead of 24 hours. This methodological improvement is a significant finding and will be useful for future source apportionment studies.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

Opioid use disorder has increased in the world in recent years and Iran ranks first in terms of opium smoking in the world. In fact, opium smoking by traditional methods, in addition to dependence on morphine, is a behavioral addiction in Iran. The body position during opium smoking is usually non-standard and non-ergonomic. Over time, changes in muscle tissue, tendons and ligaments, and the connective tissue go from elasticity to neuromuscular plasticity. This study aims to compare sway back posture and musculoskeletal problems between opium smokers and non-drug users. In this comparative and cross-sectional study, 80 opium smokers were compared with 74 non-drug users in terms of sway angle (sway back posture), and musculoskeletal complaints (NORDIC questionnaire) and the association of possible risk factors was investigated. Data were analyzed by Kolmogorov-Smirnov, Correlation Coefficient and paired-t tests using SPSS version 23. There were significant differences between two groups in terms of sway back posture (P=0.007), and neck (<0.001), upper back (<0.001) and lower back (0.006) musculoskeletal complaints. Homelessness, the lifetime duration of opium smoking (in months), and the duration of daily opium smoking (in minutes) had significant correlation with sway back posture and musculoskeletal complaints. Homelessness was the strongest predictor and had strongest correlation. Overall, an increase in the duration of sitting in non-ergonomic positions could lead to increase in sway angle and sway back posture and increase in musculoskeletal complaints of neck, upper back and lower back due to the non-neutral posture of opium smoking. It seems that plasticity and structural and functional adaptations of the posture occurs due to opium smoking and further studies are recommended.

Vitamin C status is known to be associated with several demographic and lifestyle factors. These include gender, age, ethnicity, pregnancy/lactation, body weight, smoking status and dietary habits. In the present study, our aim was to interrogate the National Health and Nutrition Examination Survey (NHANES) 2017-2018 datasets to assess the impact of these factors on vitamin C dose-concentration relationships to establish if there are higher requirements for vitamin C in certain subpopulations and the possible extent of these additional requirements. The relevant data were extracted from the NHANES 2017-2018 datasets, the final cohort of which comprised 2828 non-supplementing adult males and females (aged 18 – 80+ years) with both vitamin C serum concentrations and dietary intake data available. The data was subsequently stratified by gender, age tertiles (≤36, 37-58, ≥59 years), ethnicity (non-Hispanic white, non-Hispanic black, and total Hispanic), socioeconomic tertiles (poverty income ratios: &gt;3.0, 1.36 – 3.0, ≤1.35), weight tertiles (≤72, 72-91, ≥91 kg), BMI tertiles (≤26, 26-32, ≥32 kg/m2) and smoking status. Sigmoidal (four parameter logistic) curves with asymmetrical 95% confidence intervals were fitted to the dose-concentration data. We found that males required vitamin C intakes ~1.2-fold higher than females to reach ‘adequate’ serum concentrations of 50 µmol/L. Males had both higher body weight and a higher prevalence of smoking than females. Smokers required vitamin C intakes ~2.0-fold higher than non-smokers to reach adequate vitamin C concentrations. Relative to adults in the lighter weight tertile, adults in the heaver weight tertile required ~2.0-fold higher dietary intakes of vitamin C to reach adequate serum concentrations. We did not observe any impact of ethnicity or socioeconomic status on the vitamin C dose-concentration relationship, and although no significant difference between younger and older adults was observed at vitamin C intakes &gt; 75 mg/day, at intakes &lt; 75 mg/day, older adults had an attenuated serum response to vitamin C intake. In conclusion, certain demographic and lifestyle factors, specifically gender, smoking and body weight, have a significant impact on vitamin C requirements. Overall, the data indicate that the general population must consume ~110 mg/day of vitamin C to attain adequate serum concentrations, smokers require ~165 mg/day relative to non-smokers, and heavier people (100+ kg) require ~155 mg/day to reach the same vitamin C concentrations. These findings have important implications for global vitamin C dietary recommendations.

The structure of self-reinforced composites (SRCs) based on ultra-high molecular weight 21 polyethylene (UHMWPE) was studied by means of Wide-Angle X-Ray Scattering (WAXS), X-Ray 22 tomography, Raman spectroscopy, Scanning Electron Microscopy (SEM) and in situ tensile testing 23 in combination with advanced processing tools like Avizo, ImageJ, and Ncorr to determine the cor-24 relation between the processing conditions, on the one hand, and the molecular structure and 25 mechanical properties, on the other. SRCs were fabricated by hot compaction of UHMWPE fibers at 26 different pressure and temperature combinations without addition of polymer matrix or softener. 27 It was found by WAXS that higher compaction temperatures led to more extensive melting of 28 fibers with the corresponding reduction of the Herman’s factor reflecting the degree of molecular 29 orientation, while the increase of hot compaction pressure suppressed the melting of fibers within 30 SRCs at a given temperature. X-Ray tomography proved the absence of porosity while polarized 31 light Raman spectroscopy measurements for both longitudinal and perpendicular fiber orienta-32 tions showed qualitatively the anisotropy of SRC samples. SEM revealed that the matrix was 33 formed by interlayers of molten polymer entrapped between fibers in SRCs. Moreover, in situ 34 tensile tests demonstrated the increase of Young’s modulus and tensile strength with increasing 35 temperature.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

This paper develops a novel dynamic correction method for the reliability assessment of large oil-immersed power transformers. First, with the transformer oil-paper insulation system (TOPIS) as the target of evaluation and the winding hot spot temperature (HST) as the core point, an HST-based static ageing failure model is built according to the Weibull distribution and Arrhenius reaction law, in order to describe the transformer ageing process and calculate the winding HST for obtaining the failure rate and life expectancy of TOPIS. A grey target theory based dynamic correction model is then developed, combined with the data of Dissolved Gas Analysis (DGA) in power transformer oil, in order to dynamically modify the life expectancy calculated by the built static model, such that the corresponding relationship between the state grade and life expectancy correction coefficient of TOPIS can be built. Furthermore, the life expectancy loss recovery factor is introduced to correct the life expectancy of TOPIS again. Lastly, a practical case study of an operating transformer has been undertaken, in which the failure rate curve after introducing dynamic corrections can be obtained for the reliability assessment of this transformer. The curve shows a better ability of tracking the actual reliability level of transformer, thus verifying the validity of the proposed method and providing a new way for transformer reliability assessment. This contribution presents a novel model for the reliability assessment of TOPIS, in which the DGA data, as a source of information for the dynamic correction, is processed based on the grey target theory, thus the internal faults of power transformer can be diagnosed accurately as well as its life expectancy updated in time, ensuring that the dynamic assessment values can commendably track and reflect the actual operation state of the power transformers.

The aim of this pilot study was to investigate whether single nucleotide polymorphisms (SNP) in the gene encoding the catalytic subunit of glutamate cysteine ligase (GCLC) are associated with the risk and clinical features of psoriasis. A total of 944 unrelated individuals, including 474 patients with a diagnosis of psoriasis and 470 healthy controls, were recruited for the study. Six common SNPs in the GCLC gene were genotyped using the MassArray-4 system. Polymorphisms rs648595 (OR=0.56 95%CI 0.35-0.90, Pperm=0.017) and rs2397147 (OR=0.54 95%CI 0.30-0.98, Pperm=0.05) were associated with susceptibility to psoriasis in males. In the male group, diplotype rs2397147-C/C×rs17883901-G/G was associated with decreased risk of psoriasis (FDR-adjusted P=0.014), whereas diplotype rs6933870-G/G×rs17883901-G/G (FDR-adjusted P=0.045) showed association with increased disease risk in females. Joint effects of SNPs with tobacco smoking (rs648595 and rs17883901) and alcohol abuse (rs648595 and rs542914) on the risk of psoriasis were observed (Pperm≤0.05). Furthermore, we found multiple sex-independent associations between GCLC gene polymorphisms and various clinical features such as earlier disease onset, the psoriatic triad, and specific localizations of skin lesions. The present study is the first to show that polymorphisms of the GCLC gene are significantly associated with the risk of psoriasis and related to its clinical features.

A recent review of global vitamin C status indicated a high prevalence of deficiency, particularly in low- and middle-income countries, as well as in specific subgroups within high-income countries. Here we provide a narrative of potential factors influencing vitamin C status. The in vivo status of vitamin C is primarily affected by dietary intake and supplement use. Dietary intake can be influenced by cultural aspects such as staple foods and traditional cooking practices. Environmental factors can also affect vitamin C intake and status; these include geographic region, season and climate, as well as pollution. Demographic factors such as sex, age, and race are known to affect vitamin C status, as do socioeconomic factors such as deprivation, education and social class, and institutionalization. Various health aspects affect vitamin C status; these include body weight, pregnancy and lactation, genetic variants, smoking, and disease states, including severe infections as well as various non-communicable diseases such as cardiovascular disease and cancer. Some of these factors have changed over time, therefore we also explore if vitamin C status has shown temporal changes. Overall, there are numerous factors that can affect vitamin C status to different extents in various regions of the world. Many of these factors are not taken into consideration during the setting of global recommended dietary intakes for vitamin C.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

Safe administration of highly cytotoxic chemotherapeutic drugs is a challenging problem in cancer treatment due to the adverse side effects and collateral damage to non-tumorigenic cells. To mitigate these problems, new promising approaches, based on the paradigm of controlled targeted drug delivery (TDD), utilizing drug nanocarriers with biorecognition ability to selectively target neoplastic cells, are being considered in cancer therapy. Herein, we report on the design and testing of a nanoparticle-grid based biosensing platform to aid in the development of new targeted drug nanocarriers. The proposed sensor grid consists of superparamagnetic gold-coated core-shell Fe₂Ni@Au nanoparticles, further functionalized with folic acid targeting ligand, model thiolated chemotherapeutic drug doxorubicin (DOX), and a biocompatibility agent, 3,6,-dioxa-octanethiol (DOOT). The employed dual transduction based on electrochemical and enhanced Raman scattering detection have enabled efficient monitoring of the drug loading onto the nanocarriers, attached to the sensor surface, as well as the drug release under simulated intracellular conditions. The grid’s nanoparticles serve here as the model nanocarriers for new TDD systems under design and optimization. The superparamagnetic properties of the Fe₂Ni@Au NPs aid in nanoparticles’ handling and constructing a dense sensor grid with high plasmonic enhancement of the Raman signals due to the minimal interparticle distance.

A new lateral force-resisting wall panel is presented for applications in mid-rise prefabricated lightweight steel construction in seismic prone regions. This panelised system is composed of a hot-rolled frame and cold-formed studs and tracks, which works as a lateral force resisting system in lightweight steel framing. The proposed hybrid panel system exhibits proper ductility and energy dissipation behaviour. The hysteretic responses of full-scale panel experiments demonstrate that the system can safely resist high cyclic loads. The hot-rolled steel part, on the other hand, can significantly improve the initial lateral stiffness of the total system that will control the maximum allowable drift of multi-story buildings. Finally, in a case study, by applying the proposed system to the design of a mid-rise building in a high seismic area, the performance of the hybrid panels, are compared with those of fully hot-rolled systems (moment resisting frames) and fully cold formed systems. The findings indicate that applying hybrid panels will result in lower weights and better performance in seismic prone regions.

Number of studies claim that tobacco control (TC) regulations are associated with reductions in smoking-related hospitalisation rates, however very few have estimated the impact of TC laws (TCL) at both countrywide and regional levels, and none of them - in relation to compliance with TC regulations. This study evaluates the effects of Russian TCL on hospital admission (HA) rates for pneumonia countrywide and in 10 Russian regions and the extent of these effects in connection with the compliance to TCL. Methods: HA rates for pneumonia during 2005–2019 were analysed to compare the periods before and after the adoption of TCL in 2013. An interrupted time series design and a Poisson regression model were used to estimate the immediate and long-term effects of TCL on pneumonia annual hospitalisation rates after the TCL adoption, compared with the pre-law period. The 10 Russian regions were compared using the TCL Implementation Scale (TCIS) developed on the basis of the results of Russian TC policy evaluation survey; Spearman’s rank correlation and linear regression models were employed. Results showed a 14.3% reduction in HA rates for pneumonia (RR 0.88; p=0.01) after the adoption of TCL in Russia with significant long-term effect after 2013 (RR 0.86; p=0.006). Regions with better enforcement of TCL exhibited greater reductions in pneumonia HA rates (rsp=−0.55; p=0.04); (=−4.21; p=0.02). Conclusions: TCL resulted in a sustained reduction in pneumonia hospitalisation rates, but these effects, varying by region, may depend on the scale of the TCL enforcement.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

This study introduces a remote sensing application using satellite imagery to survey a network-scale aggregate stockpile inventory. First, a real scale aggregate quarry site was surveyed using a small Unmanned Aerial Vehicle (sUAV) to produce digital terrain models that enabled analysis of aggregate pile geometry. Second, a lab experiment was designed and performed to validate the applicability of close-range Structure from Motion (SfM) photogrammetry for measuring aggregate piles' physical properties such as volume and density. The other part of the lab experiment delved into direct measurement of aggregate density under varying compaction efforts. These experimental results, in conjunction with some simplifying assumptions, enabled the calculation of aggregate stockpile volumes and estimated weights from satellite imagery. We estimated that an inventory of 4.4 and 1.1 million metric tons of crushed aggregates and Reclaimed Asphalt Pavement (RAP), respectively, stockpiled in Washington State for asphalt production in 2017. The merit of producing such database was further showcased in an example on the economic and environmental impacts of material transportation. We approximated that hauling aggregates from quarry plants to construction sites within Washington State incurs a cost of about $50 thousand to over $4 million, consumes about 0.25 to 20 TJ of energy, and emits 20 to over 1,500 tons of CO₂-eq per asphalt plant annually.