Full-scale/model test comparison studies to validate the traditional ABL wind tunnel simulation technique are reviewed. According to the literature review, notable discrepancies between full-scale measurement results and model test results were observed by most performed comparison studies, but the causes of the observed discrepancies were not revealed in a scientific way by those studies. In this regard, a new research scheme for future full-scale/model test comparison studies is proposed in this article, which utilizes the multiple-fan actively controlled wind tunnel simulation technique. With the new research scheme, future full-scale/model test comparison studies are expected to reasonably disclose the main problems with the traditional ABL wind tunnel simulation technique, and the technique can be improved correspondingly.

To delve into the structure-function relationship of transmembrane proteins (TMPs), robust protocols are needed to produce them in a pure, stable, and functional state. Among all hosts that express heterologous TMPs, E. coli has the lowest cost and fastest turnover. However, many of the expressed in E. coli TMPs are misfolded. Several strategies have been developed to either direct the foreign TMPs to E. coli’s membrane or retain them in a cytosolic soluble form to overcome this deficiency. Here, we summarize protein engineering methods to produce chimera constructs of the desired TMPs fused to either signal peptide or precursor maltose binding protein (pMBP) to direct the entire construct to the periplasm, therefore depositing the fused TMP in the plasma membrane. We further describe strategies to produce TMPs in soluble form by utilizing N-terminally fused MBP without signal peptide. Depending on its N- or C-terminus location, a fusion to apolipoprotein A-I can either direct the TMP to the membrane or shield the hydrophobic regions of the TMP, maintaining the soluble form. Strategies to produce G-protein coupled receptors, TMPs of Mycobacterium tuberculosis, HIV-1 Vpu, and other TMPs are discussed. This knowledge could increase the scope of TMPs’ expression in E. coli.

This study aimed to assess the microbiological quality of set of fruits and vegetables sold on stalls in the streets and open markets of Dakar, the capital city of Senegal. Samples purchased in seven sites were analyzed to isolate E. coli, Salmonella spp. and Vibrio spp. Some primary samples with a positive microbiological culture were subjected to DNA extraction and subsequent metagenomic analysis. A total of 240 fresh fruit and vegetable samples were collected including lettuce (n=40), tomatoes (n=40), mango slices (n=40), onion slices (n=40), mint leaves (n=40), strawberries and grapes (respectively n=20). Of these samples, 50.83% (122/240) and 60.41% (145/240) was contaminated with Escherichia coli and Vibrio spp. respectively, while Salmonella was not isolated in any product. Levels of contamination with both E. coli (1.3 103 to 6 106 CFU/g) and Vibrio spp. (4.55 102 to 8.73 106 CFU/g) were significantly above the thresholds acceptable for human consumption. The most contaminated samples were lettuce with a prevalence of 98% (39/40) for E. coli and for Vibrio spp. followed by mint leaves with 100% (40/40) and 93% (37/40) of the samples containing for E. coli and Vibrio spp. respectively. Out of 46 samples sequenced, metagenomic analysis revealed high contamination rates for E. coli, Vibrio spp. and Salmonella spp. with 100%, 67.39% and 93.47% of prevalence respectively. On the other hand, the alpha diversity analysis shows a high bacterial diversity in lettuce and mint leaf samples while beta diversity analysis highlighted the presence of two major clusters. Our results stress the need of a surveillance system that extends this investigation to a national scale while increasing the number of sampling sites and products analyzed.

The purpose of this research was to analyze the moderating effect of clean energy innovation on the relationship between corporate carbon footprint and corporate profits in those industrial sectors associated with high demand for fossil fuels in which it is "hard to abate" CO₂e emissions. It used a longitudinal research design, in particular a panel study under a structural equation modeling (SEM) approach, based on partial least squares. For the longitudinal moderation analysis, this research employed the Bayesian method by defining a multiple-indicator latent growth curve model (B-LGC model). A global sample was used consisting of 7,827 firm-year observations between 2015 and 2021 corresponding to 167 international firms. The results revealed a very significant impact of the corporate carbon footprint on corporate profits. Likewise, the results showed that innovations in clean energy, when measured as the consumption of renewable energy, positively moderates the relationship between the greenhouse gas emissions from the value chain associated with Scope 3 of the Greenhouse Gas (GHG) Protocol, and the gross profit margin obtained. Besides the academic contribution represented by the moderating effect of clean energy innovation, these findings imply that a more detailed understanding of the emissions of the entire value chain (Scope 3 CO₂e) by executives and managers of high emitting CO₂e companies represents an effective mechanism to obtain higher profits, create competitive advantages and, at the same time, achieve a net zero emissions strategy. More importantly, public policy makers will be able to use these results to revise CO₂e-related policies paying more attention to the Scope 3 CO₂e emissions produced by these companies, to formulate regulatory and control mechanisms that stimulate clean energy innovation.

Geomagnetic induced current (GIC) is a ground end manifestation associated with the space weather perturbations that should be greatly taken into account by the society. Although the GICs implication to the power system is not regular, it can cause large scale of system failure. In equatorial, the power system is considered safe since the most intense of geomagnetic storm happened in high latitude. However, the internal damage due to GICs which finally led to the South African power system failure has totally changed the normal perception. Therefore, a preliminary investigation on the GICs activity in equatorial region is performed to understand the space weather impact to the power system. Time derivative of the horizontal magnetic field component (dB/dt) is done to indicate the GICs activity value based on Faraday’s law. All the reported power failures are compiled to produce the threshold value of dB/dt, which possibly cause the harmful effect to the system. Then, dB/dt analysis is extended to show the pattern of GICs activity in function of magnetic latitude and local time. The results reveal that power network in equatorial region has possibly suffered by GIC. Plus, high number of intense GIC activity in this region occurred during dayside.

Genetic variations at the Apolipoprotein E (ApoE) and microtubule-associated protein tau (MAPT) loci have been implicated in multiple neurogenerative diseases, but their exact molecular mechanisms are unclear. In this study we performed transcript level linear modelling using the blood whole transcriptome data and genotypes of the 570 subjects in the Parkinson’s progression markers initiative (PPMI) cohort. ApoE, MAPT haplotypes and two SNPs at the SNCA locus (rs356181, rs3910105) were used to detect expression quantitative trait loci eQTLs associated with the transcriptome and differential usage of transcript isoforms. As a result, we identified 151 genes associated with the genotypic variations, 29 cis and 122 trans eQTL positions. Profound effect with genome-wide significance of ApoE e4 haplotype on the expression of TOMM40 transcripts was identified. This finding potentially explain in part the frequently established genetic association with the APOE e4 haplotypes in neurodegenerative diseases. Moreover, MAPT haplotypes had significant differential impact on 23 transcripts from the 17q21.31 and 17q24.1 loci. MAPT haplotypes had also the largest (256) and smallest (-178) effect sizes measured as beta values on two different transcripts from the same gene (LRRC37A2). Intronic SNP in the SNCA gene, rs3910105, differentially induces expression of three SNCA isoforms. In conclusion, this study established clear association between well-known haplotypic variance and transcript specific regulation in the blood. APOE e4 and MAPT H1/H2 haplotypic variants are associated with the expression of several genes related to the neurodegeneration.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

Given the rise in the number of cases and their recurrences, Urinary Tract Infections (UTI) are one of the major burdens on public healthcare worldwide. Rapid, inexpensive and selective detection of Uropathogenic E. coli (UPEC), a major contributor to UTIs, is the need of the hour for effective treatment, given the rise of antibiotic-resistant bacteria due to improper diagnosis. Here we present a rapid, real-time, selective and label-free detection of UPEC using an integrated sensing platform based on Crossed Surface Relief Gratings (CSRGs) as nanoplasmonic sensors. Detection is achieved due to the unique Surface Plasmon Resonance (SPR)-based light energy exchange attributed to the CSRGs, allowing real-time sensing in a very narrow bandwidth of the incident light to pass where the SPR energy conversion occurs. The sensing ability of the platform is experimentally demonstrated by the detection of bulk Refractive Index (RI) changes, with a bulk sensitivity of 382.2 nm/RIU and a resolution in the order of 10-6 RIU. We demonstrate selective capture and detection of clinical concentration of UPEC, as opposed to other gram-negative bacteria, in real-time, a first for CSRGs. This work is particularly important for effective treatment of UTIs, allowing point-of-care diagnosis for economically disadvantaged regions around the world.

The greenhouse gases and air pollution generated by extensive energy use have exacerbated climate change. An electric-bus (e-bus) transportation system favors reducing pollution and carbon emissions. This study analyzed the minimization of construction costs for an all battery-swapping public e-bus transportation system. A simulation was conducted according to existing timetables and routes. Daytime charging was incorporated during the hours of operation; the two parameters of the daytime charging scheme were the residual battery capacity and battery-charging energy during various intervals of daytime peak electricity hours. The parameters were optimized using three algorithms: particle swarm optimization (PSO), a genetic algorithm (GA), and a PSO–GA. This study observed the effects of optimization on cost changes (e.g., number of e-buses, on-board battery capacity, number of extra batteries, charging facilities, and energy consumption) and compared the plug-in and battery-swapping e-bus systems. The results revealed that daytime charging can reduce the construction costs of both systems. In contrast to the other two algorithms, the PSO–GA yielded the most favorable optimization results for the charging scheme. Finally, according to the cases investigated and the parameters of this study, the construction cost of the plug-in e-bus system was lower than that of the battery-swapping e-bus system.

Aluminium alloys are used for fabrication of fuel clad of research grade nuclear reactors as well as of several types of core components of high flux research reactors. In order to carry out design and safety analysis of these components, their mechanical and fracture properties are required by the designer. In this work, experiments have been conducted on tensile specimens machined from an aluminium alloy block to evaluate the material stress-strain curve. For evaluation of fracture properties, experiments have been conducted on disc shaped compact tension specimens in order to determine the fracture toughness of aluminium alloy. From crystal plasticity based finite element analysis and experimental data, a material damage parameter for prediction of crack initiation has been evaluated. The variation of the parameter for various values of initial a/W ratios of the disc-shaped CT specimens have been studied. It was observed that the damage parameter is independent of crack geometry and hence, it qualifies as transferable material property which can be used to predict crack initiation in a component of this material subjected to different kinds of loading conditions. In addition, the JR curves of the disc-shaped CT specimens have also been evaluated from experiments. The material damage parameter has also been used to study the crack initiation in single crystal fracture specimens with two different orientations. It was observed that the [111] orientation is more susceptible to crack initiation and propagation compared to the [100] orientation as the damage parameter is high in the ligament of the specimen ahead of the crack-tip for the same level of load. The results of the experiments and the material damage parameter shall be helpful for integrity analysis of fuel clad of research reactors as well as components of high flux research reactors.

Estimating the infection risks in indoor environments comprises the assessment of the behavior of virus-laden aerosols, i.e. spreading, mixing, removal by air purifiers etc. A promising experimental approach is based on using non-hazardous surrogate aerosols of similar size, e.g. salt particles, to mimic the virus aerosol behavior. This manuscript addresses the issue how a successful transfer of such experiments can be accomplished. Corresponding experiments in two very different environments, a large community hall and a seminar room, with optional use of air purifiers in various constellations were conducted. While high particle concentrations are advantageous in terms of avoiding influence of background aerosol concentrations, it is shown that appropriate consideration of aggregation and settling are vital to theoretically describe the experimentally determined course of particle concentrations. A corresponding model equation for a well-mixed situation is derived and the required parameters are thoroughly determined in separate experiments independently. It is demonstrated that clean air delivery rates (CADR) of air purifiers determined with this approach may differ substantially from common approaches not explicitly taking into account aggregation.

The effects of simulated acid rain (SAR) on the photosynthetic performance of subtropical coniferous species have not been thoroughly investigated. In this study, we treated two coniferous species, Pinus massoniana (PM) and Cunninghamia lanceolata (CL), with SAR and then analyzed photosynthetic activities via the simultaneous measurement of prompt fluorescence(PF), delayed fluorescence(DF), and modulated reflection at 820 nm(MR820). Following the low-pH SAR treatment, the I–P phase of the OJIP curves of PM and CL decreased significantly and then the K-band and L-band were detectable. The delayed fluorescence for both PM and CL decreased as the pH of the SAR solution decreased, with a more significant decrease in the I1 peak than in the I2 peak. According to the MR820 curve, the exposure to SAR stress inhibited the rapid decrease and slow increase in the MR820 transients of PM and CL. The gradients of the decreasing and increasing phases were lower for CL than for PM at pH 2.5. In addition, SAR decreased the light energy captured per unit area (ABS/CSm) and the quantum yield of electron transfer per unit area (ETO/CSm), but it increased the accumulation of QA−, thereby decreasing primary photochemical efficiency (TRO/CSm, φPO). These changes in photosystem II (PSII) resulted in a decrease in the maximum quantum yield of PSII (Fv/Fm) and the performance index (PIABS). Moreover, PSII was protected from thylakoid membrane photodamages through the increase in heat dissipation per unit area (DIO/CSm) in response to SAR. The increase in δRO as the pH of the SAR solution decreased was observed for PM, but not for CL. Considered together, the study findings suggest that SAR treatments can decrease chlorophyll contents and damage the OEC in PM and CL, which obstructs the transfer of electrons on the donor and acceptor sides of PSII. However, PM is better able to withstand SAR stress than CL, likely because of the activation of a protective mechanism (reflected by the change in δRO). Therefore, in coniferous forest areas severely affected by acid rain, CL may need to be protected more than PM.

Control of canine infections with Leishmania infantum (L. infantum), a major zoonotic disease in Brazil and southern Europe is becoming increasingly important due to their close proximity to humans, the increasing import of dogs from endemic regions and impact of climate change on vector spreading. Simple, rapid and reliable diagnostic tests are therefore needed to detect infected dogs. Here, we re-evaluated different serological methods for the diagnosis of canine leishmaniosis (CanL) in Croatia and Brazil. The diagnostic performance of the indirect fluorescent antibody test (IFAT) and the VetLine® Leishmania ELISA was compared with three rKLi8.3 based diagnostic test systems, the rKLi8.3 ELISA, the INgezim® Leishma CROM lateral flow test (LFT) and the VetBlot® Leishmania LineBlot. CanL symptomatic dogs were efficiently diagnosed by all tests, except the VetLine® Leishmania ELISA, which is based on whole Leishmania antigens. The advantage of rKLi8.3 was also observed in oligo-and asymptomatic dogs from Brazil and Croatia, although with reduced diagnostic efficiency compared to symptomatic dogs. Similar to IFAT and rKLi8.3 ELISA, the LFT did not cross-react with other common canine pathogens, showed a very high specificity for healthy dogs from endemic regions of both countries and did not react with healthy, vaccinated dogs in Brazil. In conclusion, sero-diagnostic tests based on the rKLi8.3 antigens are superior to whole parasite antigens and the LFT has the advantage of providing a laboratory independent, rapid and specific diagnosis of CanL.

The work consisted in identifying possible effects from heavy metals (HMs) pollution due to waste disposal activities in three potentially polluted sites located in Basilicata (Italy), where a release of pollutants with values over the thresholds allowed by the Italian legislation was detected. The potential variations in the physiological efficiency of vegetation have been analyzed through the multitemporal processing of satellite images. In detail, Landsat 5 Thematic Mapper (TM) and Landsat 8 Operational Land Imager (OLI) images were used to calculate the Normalized Difference Vegetation Index (NDVI) trend over the years. Then, the multitemporal trends were analyzed using the median of Theil-Sen, a non-parametric estimator particularly suitable for the treatment of remote sensing data, being able to minimize the outlier effects due to exogenous factors. Finally, the subsequent application of the Mann-Kendall test on the trends identified by Theil-Sen slope allowed the evaluation of trends significance and, therefore, the areas characterized by the effects of contamination on vegetation. The application of the procedure to the three survey sites led to the exclusion of the presence of significant effects of HMs contamination on the vegetation surrounding the sites during the years of waste disposal activities.

A wide variety of bacteria, fungi and plants can produce bioactive secondary metabolites, which are often referred to as natural products. With the rapid development of DNA sequencing technology and bioinformatics, a large number of putative biosynthetic gene clusters have been reported. However, only a few natural products can be detected when isolated species are grown under conventional laboratory conditions, as most biosynthetic gene clusters are not expressed or are expressed at extremely low levels at these conditions. With the rapid development of synthetic biology, advanced genome mining and modification strategies have been reported, and they provide new opportunities for discovery of natural products. This review discusses advances in recent years that can accelerate the design, build, test, and learn (DBTL) cycle of natural product discovery, and prospects trends and key challenges for future research directions.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Chronic diseases are still known as incurable diseases, and we suspect that the medical research model is unfit for characterizing chronic diseases. In this study, we examined accuracy and reliability required for characterizing chronic diseases, reviewed implied presumptions in clinical trials and assumptions used in statistical analysis, examined sources of variances normally encountered in clinical trials, and conducted numeric simulations by using hypothetical data for several theoretical and hypothetical models. We found that the sources of variances attributable to personal differences in clinical trials can distort hypothesis test outcomes, that clinical trials introduce too many errors and too much inaccuracies that tend to hide weak and slow effects of treatments, and that the means of treatments used in statistical analysis have little or no relevance to specific patients. We further found that a large number of uncontrolled co-causal or interfering factors normally seen in human subjects can greatly enlarge the means and the variances of the experimental errors, and the use of high rejection criteria (e.g., low p values) further raises the chances of failing to find treatment effects. As a whole, we concluded that the research model using clinical trials is wrong on multiple grounds, under any of our realistic theoretical and hypothetical models, and that misuse of statistical analysis is most probably responsible for failure to identify treatment effects for chronic diseases and to detect harmful effects of toxic substances in the environment. We proposed alternative experimental models involving the use of single-person or mini optimization trials for studying low-risk weak treatments.

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

This paper introduces an approach that chooses the fault detection by calculating probabilities using probability mass function (pmf) and cumulative distribution function (CDF). This work used a method for multiple stuck-at faults by producing a new test pattern in combinational circuits. We assumed that existence of all multiple faults is only because of one single component that is faulty. A complete test set can be created by all possible single stuck-at faults in a combinational circuit using some combination of gates. The test set generation fault detection method is applied on two different 3-bit input variable and 4-bit input variable circuits. The probability of error occurrence is calculated at both 3-bit and 4-bit input variable circuits. The resulting feature is used to obtain maximum error occurrence probability to detect faults by the logic used that the complexity of the circuit is inversely proportional to the fault occurrence probability. Then again, undetectability is directly proportional to the complexity of the circuit. Therefore, finest feasible circuit should have large input variable components with less complexity to reduce the fault occurrence probability.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

Artificial Intelligence (AI) and Deep Reinforcement Learning (DRL) have revolutionised e-learning by creating personalised, adaptive, and secure environments. However, challenges such as privacy, bias, and data limitations persist. E-FedCloud aims to address these issues by providing more agile, personalised, and secure e-learning experiences. This study introduces E-FedCloud, an AI-assisted adaptive e-learning system that automates personalised recommendations and tracking, thereby enhancing student performance. It employs federated learning-based authentication to ensure secure and private access for both course instructors and students. Intelligent Software Agents (ISAs) evaluate weekly student engagement using the Shannon Entropy method, classifying students into either engaged or not-engaged clusters. E-FedCloud utilises weekly engagement status, demographic information, and an innovative DRL-based early warning system, specifically ID2QN, to predict the performance of not-engaged students. Based on these predictions, the system categorises students into three groups: risk of dropping out, risk of scoring lower in the final exam, and risk of failing the end exam. It employs a multi-disciplinary ontology graph and an attention-based capsule network for automated, personalised recommendations. The system also integrates performance tracking to enhance student engagement. Data is securely stored on a blockchain using the LWEA encryption method.

To develop a modern plague vaccine, we used hypo-endotoxic Yersinia pestis bacterial ghosts (BGs) with combinations of genes encoding the bacteriophage ɸX174 lysis-mediating protein E and/or holin-endolysin systems from λ or L-413C phages. Expression of the protein E gene resulted in the BGs that retained the shape of the original bacterium. Co-expression of this gene with genes coding for holin-endolysin system of the phage L-413C caused formation of structures resembling collapsed sacs. Such structures, which have lost their rigidity, were also formed as a result of the expression of only the L-413C holin-endolysin genes. Similar holin-endolysin system from phage λ containing mutated holin gene S and intact genes R-Rz coding for the endolysins caused generation of mixtures of BGs that had (i) practically preserved and (ii) completely lost their original rigidity. The addition of protein E to the work of this system shifted the equilibrium in the mixture towards the collapsed sacs. The collapse of the structure of BGs can be explained by endolysis of peptidoglycan sacculi. Immunizations of laboratory animals with the variants of BGs followed by infection with a wild-type Y. pestis strain showed that bacterial envelopes protected only cavies. BGs with peptidoglycan maximally hydrolyzed had a greater protectivity compared to BGs with preserved peptidoglycan skeleton.

The present study was aimed to evaluate the levels of oxidative stress markers in breast diseases by measuring the 8-hydoxy-2-deoxyguanosine (8-OHdG), vitamin A, vitamin C, vitamin E and total antioxidant status (TAS) alterations in relation to cell proliferation activity and disease progression. Significant increases in the level of oxidative damage marker 8-OHdG and cell proliferation activity were observed in breast carcinoma patients in comparison to benign and normal controls, which were accompanied by significant decrease in non enzymatic antioxidants and TAS concentrations. 8-OHdG and cell proliferation level were negatively correlated with non enzymatic antioxidants viz., Vitamin A, Vitamin C, vitamin E level and total antioxidant activity. Altered levels of biomarkers of oxidative stress and cell proliferation activity amongst the malignant, benign and controls suggest a correlation of increased oxidative stress and cell proliferation activity in the progression of disease in breast carcinoma patients. Among the oxidative stress markers and cell proliferation index, decreased level of vitamin A, vitamin C, vitamin E, TAS and increased level of 8-OHdG, cell proliferation index emerged as best predicted biomarkers for subjects with malignancy and benign breast disease.

Background/Objectives: Endometriosis represents substantial direct and indirect healthcare costs impacted by absent accurate, non-invasive uniformly diagnostic tools. We endeavored to demonstrate gastrointestinal myoelectrical activity (GIMA) biomarkers unique to endometriosis allow noninvasive, uniformly accurate diagnosis or exclusion of endometriosis. Methods: Prospective open-label comparative study of 154 patients, age >18, with or without diagnosed endometriosis. Population included 62 non-endometriosis controls (Cohort 1), 43 subjects with surgically histologically-confirmed endometriosis (Cohort 2), and 49 subjects with abdominal pain and negative imaging (Cohort 3). Electroviscerography (EVG) recorded GIMA biomarkers from three abdominal electrodes before and 30-minutes post water-load protocol. Cohort 2 had postoperative EVG and Cohort 3 had preoperative EVG. Calculated specificity, sensitivity, NPV, PPV and predictive probability or C-Statistic used univariate, multivariate, linear and logistical regression analyses of the area under the curve (AUC) at all frequency and time points, including age and pain covariants. Results: Non-endometriosis cohort differed significantly from endometriosis cohorts (p<0.001) for median (IQR), and AUC percent frequency distribution of power at baseline, 10-minute, 20-minute, and 30-minute post water-load at all frequency ranges 15-20cpm, 30-40cpm and 40-50cpm. Endometriosis cohorts were statistically similar (p>0.05). GIMA biomarker threshold scoring demonstrated 95%/91% sensitivity and PPV, 96%/95% specificity and NPV and C-statistic of >99%/98% respectively for age subsets. GIMA biomarkers in Cohort 3 predicted 47/49 subjects positive and 2/49 negative for endometriosis, confirmed surgically. Hormonal therapy, surgical stage, nor pain score affected diagnostic accuracy. Conclusions: Non-invasive electroviscerography with GIMA biomarker detection distinguished participants with and without endometriosis based upon endometriosis specific GIMA biomarkers threshold scoring.

Cervical cancer, primarily caused by high-risk human papillomavirus (HR-HPV) types 16 and 18, is a major global health concern. Persistent HR-HPV infection can progress from reversible pre-cancerous lesions to invasive cervical cancer, which is driven by the oncogenic activity of human papillomavirus (HPV) genes, particularly E6 and E7. Traditional screening methods, including cytology and HPV testing, have limited sensitivity and specificity. This review explores the ap-plication of p16/Ki-67 dual-staining cytology for cervical cancer screening. This advanced im-munocytochemical method allows for simultaneously detecting p16 and Ki-67 proteins within cervical epithelial cells, offering a more specific approach for triaging HPV-positive women. Dual staining and traditional methods are compared, demonstrating their high sensitivity and negative predictive value but low specificity. The increased sensitivity of dual staining results in higher detection rates of CIN2+ lesions, which is crucial for preventing cervical cancer progression. However, its low specificity may lead to increased false-positive results and unnecessary biopsies. The implications of integrating dual staining into contemporary screening strategies, particularly considering the evolving landscape of HPV vaccination and changes in HPV genotype prevalence are also discussed. New guidelines and further research are necessary to elucidate the long-term effects of integrating dual staining into screening protocols.

Among all the active confinement techniques, the use of pre-tensioned stainless steel straps has recently gained much attention. The flexibility of the stainless steel straps allows us to bend and pass them through the thickness of the masonry, thus creating a three-dimensional strengthening system between the two opposite facings. The use of the same perforation for the passage of several straps closed in a loop generates a continuous strengthening system that prevents parts of the structure from falling and injuring the occupants during seismic events. However, the perforations can nullify the in-plane strengthening, as they act as cylindrical hinges and make the reinforcement system labile for certain strap arrangements. Diagonal compression tests on square masonry panels performed in the present study show that the straps improve neither strength nor ductility when running along the mortar head and bed joints, arranged in square meshes. Conversely, they improve both strength and ductility when the straps make angles of 45° with the mortar joints. Furthermore, the experimental results show that the straps exert an anisotropic effect that decreases the apparent in-plane Poisson ratio. They also provide new insights into the diagonal compression test and allow formulating a new proposal for the pseudo-ductility factor.

Understanding the dynamic interaction between piles and surrounding soil under vehicular impacts is essential for effectively designing and optimizing soil-embedded vehicle barrier systems. The complex behavior of pile-soil systems under impact loading, attributed to the soil’s nonlinear behavior and large deformation experienced by both components, presents significant simulation challenges. Popular computation techniques, such as the Updated Lagrangian Finite Element Method (UL-FEM), encounter difficulties in scenarios marked by large soil deformation, e.g., impacts involving rigid piles. While mesh-free particle and discrete element methods offer another option, their computational demands for field-scale pile-soil impact simulations are considerable. We introduce the erosion method to bridge this gap by integrating UL-FEM with an erosion algorithm designed for simulating large soil deformations during vehicular impacts. Validation against established physical impact tests confirmed the method’s effectiveness for flexible and rigid pile failure mechanisms. Additionally, this method was used to investigate the effects of soil mesh density, soil domain sizes, and boundary conditions on the dynamic impact response of pile-soil systems. Our findings provide guidelines for optimal soil domain size, mesh density, and boundary conditions. This investigation sets the stage for improved, computationally efficient techniques for the pile-soil impact problem, leading to better pile designs for vehicular impacts.

Diabetes mellitus is a widespread chronic metabolic disorder demanding regular blood glucose level surveillance (BGLs). Current invasive techniques, such as finger-prick tests, often result in discomfort for patients, leading to infrequent monitoring and potential health complications. The primary objective of this study was to design a novel, portable, non-invasive system for diabetes detection using breath samples, named as DiabeticSense, an affordable digital health device for early detection, encouraging immediate intervention. The device employed MOSFET-based electrochemical sensors to assess volatile organic compounds in breath samples, whose concentrations differ between diabetic and non-diabetic individuals. The system merged body vital signs with sensor voltages obtained by processing breath sample data to predict diabetic conditions. Our research used readings from 100 patients at a nationally recognised hospital to form the dataset. Data was then processed 10 using a Gradient Boosting Classifier model, and performance was cross-validated. The proposed system attained a promising accuracy of 86.6%, marking an improvement of 20.72% over an existing regression technique. The developed device introduces a non-invasive, cost-effective, and user-friendly solution for preliminary diabetes detection. It has the potential to increase patient adherence to regular monitoring.

To improve the understanding of soil–pile interaction of laterally loaded piles, the quasi-static test of pile group foundation in silty clay with 5 foundation piles arranged in cross shape is carried out. The direct measurement-based p–y curves at different depths showed nonlinear behavior, in which the initial stiffness and ultimate soil reaction increased as the depth increased. The loading displacement amplitude corresponding to the failure of each foundation pile in the high axial compression reinforced concrete pile group foundation is given as follows: the front-end nappe foundation pile (#3 pile) is 6mm, the middle pile is 16mm, the front-end nappe foundation pile is 20mm, and the loading displacement amplitude of side pile is 24mm. In silty clay, due to the existence of pile group effect, the edge effect has little effect on the horizontal foundation bed coefficient of foundation pile in pile group, while the influence of masking effect on the horizontal foundation bed coefficient of each foundation pile in pile group is not related to the position of pile, but only to the existence of masking effect, and the influence of different columns of masking effect on the horizontal foundation bed coefficient is the same.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Research Highlights: Data of advanced-age provenance tests were reanalyzed applying a new approach, to directly estimate the growth of populations at their original sites under individually generated future climates. The results reveal surprisingly high resilience potential of fir species. Background and Objectives: The growth and survival of silver fir under future climatic scenarios is insufficiently investigated at the xeric limits. The selective signature of past climate determining the current and projected growth was investigated to analyze the prospects of adaptive silviculture and assisted transfer of silver fir populations, and of the introduction of non-autochthonous species. Materials and Methods: Hargreaves’ climatic moisture deficit was selected to model height responses of adult populations. Climatic transfer distance was used to assess the relative drought stress of populations at the test site, relating these to the past conditions to which the populations had adapted. ClimateEU and ClimateWNA pathway RCP8.5 data served to determine individually past, current, and future moisture deficit conditions. Beside silver fir, other fir species from South Europe and the American Northwest were also tested. Results: Drought tolerance profiles explained the responses of transferred provenances and predicted their future performance and survival. Silver fir displayed significant within-species differentiation regarding drought stress response. Applying the assumed drought tolerance limit of 100mm relative moisture deficit, most of the tested silver fir populations seem to survive their projected climate at their origin until the end of the century. Survival is likely also for transferred Balkan fir species and for grand fir populations, but not for the Mediterranean species. Conclusions: The projections are less dramatic than provided by usual field assessments. Some results contradict generally accepted concepts. The method fills the existing gap between experimentally determined adaptive response and the predictions needed for management decisions. It also underscores the unique potential of provenance tests.

Abstract Introduction: Visual perceptual skills are essential for independent participation in self-care tasks, educational, work and leisure time activities. The effect of HIV on the visual perceptual skills is not well understood among children in low resource settings like Zimbabwe. Methods: A cross sectional comparative study was done with 30 children living with HIV and 30 children living without HIV residing in Harare urban area. The TVPS-3 was used to assess their visual perceptual skills. SPSS version 22, STATISTICA 13 and Microsoft 2016 were used for data analysis. Results: Both groups of children had mean percentile ranks below 50 on their TVPS-3 scores. Children without HIV generally performed better than those with HIV but the difference was not statistically significant in most cases. Through univariate analysis, only performance on Spatial Relations significantly differed between the two groups. Both groups had lowest scores in Basic visual perceptual skills. Age and school grade were the independent predictors of the children’s performances in the study. Conclusion: There is need for Occupational therapy services in public primary schools and in the pediatric Opportunistic Infections clinics in hospitals to be part of the health team which caters for children with visual perceptual challenges.

This study investigates the factors influencing the choice of online and offline shopping trips and their impacts on urban transportation, environment, and economy in Tehran, Iran. A questionnaire survey was conducted to collect data from 1,000 active e-commerce users who made successful orders in both online and offline services in the last 20 days of 2021 in areas 2 and 5 of Tehran. A deep neural network model was developed to estimate the type of shopping trip based on 10 indicators, such as age, gender, car ownership, delivery cost, product price, etc. The performance of the model was compared with three other algorithms: MLP, decision tree, and KNN. The results showed that the deep neural network model had the highest accuracy of 95.63%. The most important factors affecting the choice of shopping trips were delivery cost, delivery time, and product price. This study provides insights for transportation planners, e-commerce managers, and policymakers to design effective strategies for reducing transportation costs, pollutant emissions, urban traffic, and increasing user satisfaction and sustainable development.

Background: Metastatic oral squamous cell carcinoma (OSCC) is associated with poor patient prognosis. Metastasis is a complex process involving various proteins, tumor cell alterations including changes caused by the epithelial-to-mesenchymal transition (EMT) process, and interactions with the tumor microenvironment (TME). In this study, we investigate a combined protein marker system consisting of connexin 43 (Cx43), EMMPRIN (CD147), E-cadherin and vimentin during the invasive metastatic process of OSCC and the possibility of using this system for prognosis prediction. Methods: The protein expression profiles of Cx43, EMMPRIN, E-cadherin and vimentin were investigated by immunohistochemistry in tissue samples from 24 OSCC patients. The metastatic process was mapped through different regions of interest (ROI) of adjacent healthy oral mucosa (OM), center of primary OSCC, invasive front (IF), and local cervical lymph node metastases (LNM). Disease-free survival (DFS) and overall survival (OS) were the primary clinical endpoints. Results: Significant changes in the expression profiles of the different marker proteins were detected between the different ROIs (all p values < 0.05). Multivariable Cox regression analysis revealed a significant effect of increased EMMPRIN expression towards IF on DFS (p = 0.019) and OS (p = 0.023). The combined predictive analysis showed a significant predictive value of the marker system for DFS (p = 0.0017) and OS (p = 0.00044). Conclusions: The combined marker system was able to significantly predict patient prognosis. An increase in EMMPRIN expression towards IF showed the strongest effect and could be an interesting new antimetastatic therapy approach.

Excessive intracellular glucose in insulin independent tissues including nerve, nephron, lens and retina invites mishandling of metabolism of glucose resulting in a background of increased oxidative stress, advanced glycation end products (AGE) formation, lipid peroxidation and failure of antioxidant defense systems in type 2 diabetes mellitus (T2DM). All these detrimental biochemical anomalies ultimately attack biological membranes and especially capillary beds of retina and glomerulus of kidney, resulting in break-down of inner blood-retinal i.e. initiation of diabetic retinopathy (DR). If these disarrays are corrected to a large extent, development of DR can be avoided or delayed. In this prospective clinical trial, 185 patients with T2DM who received B-vitamins, vitamin-C, and E along with anti-diabetic medication for five years, demonstrated a slower rate of the development of DR and reduced abnormal biochemical mediators like reactive oxygen species (ROS), malondialdehyde (MDA), AGE, and vascular endothelial growth factor (VEGF) compared to 175 T2DM individuals who were treated with only anti-hyperglycemic drugs.

Myr47 lipopeptide consisting of hepatitis B virus (HBV) pre-S1 domain (myristoylated 2-48 peptide) is a commercialized effective anti-HBV drug, preventing the interaction of HBV with sodium taurocholate cotransporting polypeptide (NTCP) on human hepatocytes, of which the activity requires both N-myristoylation residue and specific amino acid sequence. Meanwhile, we recently reported that Myr47 reduces the cellular uptake of HBV surface antigen (HBsAg, subviral particle of HBV) in the absence of NTCP expression (Somiya; et al. Virology 2016, 497, 23–32). In this study, we analyzed how Myr47 reduces the cellular uptake of lipid nanoparticles (including liposomes (LPs) and HBsAg) without NTCP expression. By using Myr47 mutants lacking the HBV infection inhibitory activity, they could reduce the cellular uptake of LPs in an N-myristoylation-dependent manner whereas in an amino acid sequence-independent manner. Moreover, Myr47 and its mutants could reduce the interaction of LPs with apolipoprotein E3 (ApoE3) in an N-myristoylation-dependent manner regardless of their amino acid sequences. From these results, N-myristoyl residue of lipopeptides generally could interfere the LPs/HBsAg-ApoE3 complex formation, thereby reducing the cellular uptake of LPs/HBsAg. When lipid nanoparticles are used as a DDS (drug delivery system) nanocarrier, the surface modification with lipopeptides may be a new method to inhibit unwanted cellular uptake of DDS nanocarriers by non-target cells.

An accurate radiative transfer model (RTM) is essential for the retrieval of soil moisture (SM) from microwave remote sensing data, such as the passive microwave measurements from the Soil Moisture Active Passive (SMAP) mission. This mission delivers soil moisture products based upon L-band brightness temperature data, via retrieval algorithms for surface and root-zone soil moisture, the latter is retrieved using data assimilation and model support. We found that the RTM based on the tau-omega (?-ω) model, can suffer from significant errors over croplands (in average between -9.4K and + 12.0K for Single Channel Algorithm SCA; -8K and + 9.7K for Dual-Channel Algorithm DCA) if the vegetation scattering albedo (omega) is treated as a constant and the temporal variations are not accounted. In order to reduce this uncertainty, we propose a time-varying parameterization of omega for the widely established zeroth order radiative transfer ?-ω model. The main assumption is that omega can be expressed by a functional relationship between vegetation optical depth (tau) and the Green Vegetation Fraction (GVF). The validation was performed from 14 May to 13 December 2015 over 61 Climate Reference Network sites (SCRN) classified as croplands. The application of the proposed time-varying vegetation scattering albedo results in a consistent improvement for the unbiased root mean square error of 16% for SCA and 15% for DCA. The reduction for positive and negative biases was 45% and 5% for SCA and 26% and 12% for DCA, respectively. This indicates that vegetation dynamics on croplands are better represented by a time-dynamic single scattering albedo.

This study examines the role of using algorithmic HRM to make strategic decisions pertaining to HR activities in organizations. The study develops a scale to measure algorithmic HRM usage in its first phase, and in the second phase, it finds that algorithmic HRM having significant impact on the strategic HR decision making that helps and enables organization in creating the competitive advantage. Utilizing the author’s LinkedIn profile, 234 final participants considered for this research. Collected data analyzed by applying PLS SEM. It evaluates the mediation role of the HR strategic decision making, and the HR digital maturity as a moderator in seeing the impact of algorithmic HRM on the competitive advantage of the firm. The study finds a strong relationship between the algorithmic HRM usage and competitive advantage, a significant relationship between algorithmic HRM usage and the strategic HR decision making, and lastly, a significant relationship between strategic HR decision making and the competitive advantage. The moderating role of HR digital maturity was found to be insignificant in this research which paves the way for further research. This research, the model, and its findings contribute to the theory and implicate the practicality of algorithmic HRM. It's one of few papers that address the algorithmic HRM usage in the transitioning economy like Saudi Arabia.

Historically, viral hepatitis is a considerable public health problem in Central Asian countries, which may have worsened after dissolution of the Soviet Union. However, up-to-date seroepidemiological studies are lacking. The aim of the present study was, therefore, to provide current estimates of seroprevalence of viral hepatitis in Kyrgyzstan, one of the economically least developed countries in the region. We conducted a population-based cross-sectional study in 2018 in the capital of Kyrgyzstan, Bishkek (n=1075). Participants, children and adults, were recruited from an outpatient clinic. Data were collected during face-to-face interviews. A blood sample (6 ml) was collected from each participant and tested with ELISA for the presence of serological markers for five viral hepatitides (A, B, C, D and E). Poststratification weighting was performed to obtain nationally representative findings. The overwhelming majority of the study participants were positive for anti-HAV (estimated seroprevalence, 75.3%; 95% confidence interval: 72.5–77.9%). The weighted seroprevalence estimates of HBsAg, anti-HCV and anti-HDV were 2.2% (1.5–3.3%), 3.8% (2.8–5.1%), and 0.40% (0.15–1.01%), respectively. Anti-HEV seropositivity was 3.3% (2.4–4.5%). Of the 33 HBsAg positive participants, five (15%) were anti-HDV positive. Our study confirms that Kyrgyzstan remains a high endemic country for hepatitis virus A and C infections. However, seroprevalences of HBV and HDV were lower than previously reported, and based on these data, the country could potentially be reclassified from high to (lower) intermediate endemicity. The observed anti-HEV seroprevalence resembles the low endemicity pattern characteristic of high-income countries.

ORF6 is responsible for suppressing the immune response of cells infected by the SARS-CoV-2 virus. It is also the most toxic protein of SARS-CoV-2, and its actions are associated with the viral pathogenicity. Here we study in silico and in vitro the structure of the protein, its interaction with RAE1, and the mechanism of action behind its high toxicity. We show both computationally and experimentally that SARS-CoV-2 ORF6, embedded in the membranes of the endoplasmic reticulum, binds to RAE1 and sequesters it in the cytoplasm, thus depleting its availability in the nucleus and impairing nucleocytoplasmic mRNA transport. This negatively affects the cellular genome stability by compromising the cell cycle progression into the S-phase and by promoting the accumulation of RNA-DNA hybrids. Understanding the multiple ways in which ORF6 affects DNA replication may also have important implications for elucidating the pathogenesis of SARS-CoV-2 and developing therapeutic strategies to mitigate its deleterious effects on host cells.

Background: The manifestations, severity, and mortality of COVID-19 are considered to be associated with the changes in various hematological parameters and in immunity. Associations of immunoglobulin G antibodies against severe acute respiratory syndrome-linked coronavirus (IgG-SARS)-positive status with cardiac function and hematological and biochemical parameters in apparently health subjects are poorly understood. Methods: The present cross-sectional study included 307 healthy volunteers (24-69 years of age; 44.8±8.6 years; 80.4% men) and was initiated in 2019 before the COVID-19 pandemic. COVID-19 episodes were confirmed by detection of IgG-SARS against SARS-CoV-2 S1 RBD to reveal 70 IgG-SARS-positive and 237 negative participants. Numerous ultrasound characteristics were assessed by echocardiography, and 15 hematological and biochemical parameters were assayed in the blood. Descriptive and comparative analysis was based on the IgG-SARS status of the participants. Results: The left ventricular mass index, mitral ratio of peak early to late diastolic filling velocity or flow velocity across the mitral valve, and deceleration time of early mitral inflow were decreased (P<0.05) in IgG-SARS-positive participants versus those in IgG-SARS-negative participants according to multivariate logistic regression analysis. Erythrocyte sedimentation rate and platelet count were slightly increased, and blood hemoglobin was decreased in IgG-SARS-positive participants compared with those in IgG-SARS-negative participants. Conclusions: LV filling, inflammation, blood coagulation, and hemoglobin appear to be influenced by COVID-19 infection in healthy participants. These observations contribute to the development of a population recovery strategy after the episodes of COVID-19.

The epithelial-mesenchymal (E/M) hybrid state has emerged as an important mediator of elements of cancer progression, facilitated by epithelial mesenchymal plasticity (EMP). We review here evidence for the presence, prognostic significance, and therapeutic potential of the E/M hybrid state in carcinoma. We further assess modelling predictions and validation studies to demonstrate stabilised E/M hybrid states along the spectrum of EMP, as well as computational approaches for characterising and quantifying EMP phenotypes, with particular attention to the emerging realm of single-cell approaches through RNA sequencing and protein-based techniques.

Synthetic fuels play an important role in the defossilization of future aviation transport. To reduce the ecological impact of remote airports due to long range transportation of kerosene, a decentralized on-site-production of synthetic paraffinic kerosene is applicable, preferably as near-drop-in fuel or alternatively as blend. One possible solution for such a production of synthetic kerosene is the Power-to-Liquid process. The basic development of a simplified plant layout addressing the specific challenges of a decentralized kerosene production which differ from most current approaches for infrastructural well-connected regions is described. The decisive influence of the Fischer-Tropsch synthesis on the PtL process is shown by means of a steady-state reactor model which was developed in Python and serves as basis for further development of a modular environment able to represent entire process chains. The reactor model is based on reaction kinetics according current literature. The effects of adjustments of the main operation parameters on the reactor behavior are evaluated and the impacts on up- and downstream processes are described. The results prove the governing influence of the Fischer-Tropsch reactor on the PtL process and show its flexibility regarding the desired product fraction output, which makes it an appropriate solution for a decentralized kerosene production.

E-commerce businesses employ recommender models to assist in identifying a personalized set of products for each visitor. To accurately assess the recommendations’ influence on customer clicks and buys, three target areas—customer behavior, data collection, user-interface —will be explored for possible sources of erroneous data. Varied customer behavior misrepresents the recommendations’ true influence on a customer due to the presence of B2B interactions and outlier customers. Non-parametric statistical procedures for outlier removal are delineated and other strategies are investigated to account for the effect of a large percentage of new customers or high bounce rates. Subsequently, in data collection we identify probable misleading interactions in the raw data, propose a robust method of tracking unique visitors, and accurately attributing the buy influence for combo products. Lastly, user-interface issues discuss the possible problems caused due to the recommendation widget’s positioning on the e-commerce website and the stringent conditions that should be imposed when utilizing data from the product listing page. This collective methodology results in an exact and valid estimation of the customer’s interactions influenced by the recommendation model in the context of standard industry metrics such as Click-through rates, Buy-through rates, and Conversion revenue.

Undoubtedly, there is a potential impact of large language models like ChatGPT in revolutionizing information retrieval and knowledge discovery, particularly in the context of the vast amount of electronic material available. On another strong note, the current work offers a first time ever mathematical approach to accurately fine tune perplexity AI, which sets a giant step ahead towards accurate next generations AI. Having started this world leading discovery, the upper and lower bounds of perplexity AI, namely , , respectively, are obtained for the first-time ever. Concluding remarks combined with emerging open problems and next research phase are provided.

This paper aims to contribute to refining the e-values for testing precise hypotheses, especially when dealing with nuisance parameters, leveraging the effectiveness of asymptotic expansions of the posterior. The proposed approach offers the advantage of bypassing the need for elicitation of priors and reference functions for the nuisance parameters and the multidimensional integration step. For this purpose, starting from a Laplace approximation, a posterior distribution for the parameter of interest only is considered and then a suitable objective matching prior is introduced, ensuring that the posterior mode aligns with an equivariant frequentist estimator. Consequently, both Highest Probability Density credible sets and the e-value remain invariant. Some targeted and challenging examples are discussed.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

In this work, a hybrid component Fault Detection and Diagnosis (FDD) approach for industrial sensor systems is established and analyzed, to provide a hybrid schema that combines the advantages and eliminates the drawbacks of both model-based and data-driven methods of diagnosis. Moreover, it shines the light on a new utilization of Random Forest (RF) together with model-based diagnosis, beyond its ordinary data-driven application. RF is trained and hyperparameter tuned using three-fold cross validation over a random grid of parameters using random search, to finally generate diagnostic graphs as the dynamic, data-driven part of this system. This is followed by translating those graphs into model-based rules in the form of if-else statements, SQL queries or semantic queries such as SPARQL, in order to feed the dynamic rules into a structured model essential for further diagnosis. The RF hyperparameters are consistently updated online using the newly generated sensor data to maintain the dynamicity and accuracy of the generated graphs and rules thereafter. The architecture of the proposed method is demonstrated in a comprehensive manner, and the dynamic rules extraction phase is applied using a case study on condition monitoring of a hydraulic test rig using time-series multivariate sensor readings.

In this work, A hybrid component Fault Detection and Diagnosis (FDD) approach for industrial sensor systems is established and analyzed, to provide a hybrid schema that combines the advantages and eliminates the drawbacks of both model-based and data-driven methods of diagnosis. Moreover, spotting the light on a new utilization of Random Forest (RF) together with model-based diagnosis, beyond its ordinary data-driven application. RF is trained and hyperparameter tuned using 3-fold cross-validation over a random grid of parameters using random search, to finally generate diagnostic graphs as the dynamic, data-driven part of this system. Followed by translating those graphs into model-based rules in the form of if-else statements, SQL queries or semantic queries such as SPARQL, in order to feed the dynamic rules into a structured model essential for further diagnosis. The RF hyperparameters are consistently updated online using the newly generated sensor data, in order to maintain the dynamicity and accuracy of the generated graphs and rules thereafter. The architecture of the proposed method is demonstrated in a comprehensive manner, as well as the dynamic rules extraction phase is applied using a case study on condition monitoring of a hydraulic test rig using time series multivariate sensor readings.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

In this paper we describe many important aspects connected with lubricants, namely: the most cheapest organic lubricant in the word, how effectively save lubricant between pairs of friction, what kind of rational shapes for the lubricant must be, what it will be connected with wear and tear using the new organic lubricant (for this purpose formulas and curves are shown in computer program MathCad with calculation). Moreover, there is one physical model which helps to catch car exhausted gases. In conclusion, some recommendations will be given to realize them into the practice during the operation for the different mechanisms including ecology.

Direct Behavior Rating (DBR) as a behavioral progress monitoring tool can be designed as longitudinal assessment with only short intervals between measurement points. The reliability of these instruments has been evaluated mostly in observational studies with small samples based on generalizability theory. However, for standardized use in the pedagogical field, a larger and broader sample is required in order to assess measurement invariance between different participant groups and over time. Therefore, we constructed a DBR with multiple items to measure the occurrence of specific externalizing and internalizing student classroom behaviors on a Likert scale (1 = never to 7 = always). In a pilot study, two trained raters observed 16 primary school students and rated the student behavior over all items with a satisfactory reliability. In the main study, 108 regular primary school students, 97 regular secondary school students and 14 students in a clinical setting were rated daily over one week (five measurement points). IRT analyses confirmed the instrument’s technical adequacy, and latent growth models demonstrated the instrument’s stability over time. Further development of the instrument and study designs to implement DBRs are discussed.

The electronic cigarette or e-cigarette is the new alternative method to deliver nicotine. In 2007, the United States introduced vaping devices on the market. Due to their attractive taste and lack of adverse effects, these vaping devices have gained popularity among youth and adults. However, there has been increasing evidence that vaping can cause severe lung injury, and these devices release toxic chemicals into the body. E-cigarettes are recognized as a global threat to public health. Nicotine, the most prevalent chemical in vaping devices, is associated with neurological problems and cognitive decline. Long-term use of e-cigarettes can cause adverse health problems, including respiratory illnesses, asthma, bronchitis, and lung inflammation. In 2019, the Centers for Disease Control and Prevention (CDC) officially declared vaping-associated illness EVALI (e-cigarette or Vaping Product Associated Lung Injury). The US Surgeon General published an alarm in December 2016 that e-cigarette consumption among adolescents and teens in the US is a "major public health concern" and that more young people are now vaping than smoking traditional cigarettes and cigars. Since its commercial introduction in 2003, modern electronic cigarettes (or E-cigarette s) have become increasingly popular with smokers, non-smokers, and those who used to smoke who have switched to them. With such a rise in consumption, people are becoming more aware of the irritating, harmful, and perhaps cancer-causing effects on the lungs. (Chadi et al., 2019; Dinardo & Rome, 2019; Lyzwinski et al., 2022; Marrocco et al., 2022; O’Callaghan et al., 2022)

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

To enable the deployment of battery-electric vehicles (BEV) as passenger cars in the private transport sector, a suitable charging infrastructure is crucial. In this paper a methodology for efficient spatial distribution of charging infrastructure is evaluated by investigating a scenario with a market penetration of BEVs of 100 percent (around 1.3 million vehicles). It aims towards the development of various charging infrastructure scenarios - including public and private charging - which are suitable to cover the charging demand. Therefore, these scenarios are investigated in detail with focus on number of public charging points, their spatial distribution, the available charging power and the necessary capital costs. For the creation of those charging infrastructure scenarios a placement model is developed. It uses the data of a MATSim (Multi-Agent Transport Simulation) traffic simulation of the metropolitan area of Berlin to evaluate and optimize different distributions of charging infrastructure. The model uses a genetic algorithm and the principle of multi-objective optimization. The capital cost of the charging points and the mean detour car drivers must cover additionally are used as optimization criteria. Using these criteria should lead to cost efficient infrastructure solutions which provide high usability at the same time. The main advantage of the method selected is that multiple optimal solutions with different characteristics can be found and suitable solutions can be selected by using other criteria subsequently. The optimized charging infrastructure solutions show capital costs between 624 and 2950 million euro. Users must cover an additionally mean detour of 254m to 590m per charging process to reach an available charging point. According to the results a suitable ratio between charging points and vehicles is between 11:1 and 5:1. A share of fast charging infrastructure (&gt;50kW) of less than ten percent seems to be sufficient, if it is situated at main traffic routes and highly frequented places.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

The progress in markerless technologies is bringing clinicians tools to rapidly evaluate tests such as Timed Up and Go (TUG) without compromising the time of the assessment, yet it raises questions about the potential trade-off in accuracy compared to traditional marker-based systems, suggesting that the precision of these evaluations is not yet conclusively established. The OpenCap system is an easy tool to process 3D kinematics with two iPhone cameras placed in front of the subject. Previous research has primarily focused on walking and movement towards the cameras with the subject facing the cameras (WF) and thus has been unable to disentangle the differences in the movement directions. We have compared the OpenCap system with a standard marker-based system for both walking directions. In OpenCap, we found significantly worse results capturing walking facing away from the cameras (RW). Compared to the marker-based system, our findings indicate troubles measuring kinematic parameters but provide good accuracy in measuring spatial-temporal parameters. These insights pave the way for refining markerless assessment technologies, potentially enhancing their utility in clinical settings.

Dance is physically demanding, requiring physical fitness(PF) that includes upper body, lower body, core fitness, and balance for successful performance. Whether PF changes as dancers advance from when they enter(freshmen) to when they graduate from their collegiate program(seniors) is unclear. We prospectively compared collegiate dancers’ freshman-to-senior PF. We recorded PF of the upper body strength-endurance(push-ups, n=number), core strength-endurance(front, left-side, right-side, and extensor plank hold times, s=seconds), lower body power(Single-leg-hop-SLH distances % Height; Leg Symmetry Index: LSI=higher/lower*100, %), and balance(Anterior Reach Balance,%Leg-Length, LL; LSI balance=higher/lower*100, %) in 25 collegiate dancers(23 females, 2 males; freshmen age=18.2±0.6yrs). Paired t-tests(p&lt;.05) compared measures from freshmen-senior years. Across their collegiate programs, dancers’ PF remained unchanged: upper body strength-endurance push-ups numbers(p=.93), core strength-endurance plank times(left:p=.44, right:p = .67, front:p=.60, p=.22), SLH distances(left: p =.44, right:p =.85) and SLH symmetry(p=0.16). Dancers’ right leg balance(p =.08) remained similar, while the left balance(p =.02) improved with better symmetry(p&lt;.001) in senior balance scores. Overall, dancers’ PF did not change across their collegiate programs, except for greater left leg balance scores. Findings suggest that practitioners can use collegiate dancers’ freshmen baseline PF when devising rehabilitation programs and making return to activity decisions post injury throughout their dance programs.

Peptides of hydrolysates of food proteins are an easily digestible source of amino acids necessary for the body to adapt to physical stress. Commercially significant hydrolysates include whey protein, casein, and other animal proteins. Hydrolysates of plant proteins are gaining popularity, but they are less common, then animal ones. Soy protein isolate is promising for obtaining the hydrolysates due to its affordable price and balanced amino acid profile. However, there are no direct studies showing an improvement in the result of physical activity when eating soy protein isolate hydrolysate (SPIH). In this work, for the first time, the study was conducted on the safety and efficacy of SPIH during physical load on model animals (rats). It was shown that the hydrolysate did not lead to pathological changes in the viscera, food intake, and weight of animals did not differ from the control group (animals consumed whey protein). Under physical load rats enteral fed SPIH showed a tendency to adapt more quickly to physical stress than the control group and the group of animals that was fed by free amino acids. The metabolites of animal blood serum were studied by NMR spectroscopy. It was shown that by the 95th minute after feeding in the group of rats receiving SPIH, the difference of proteinogenic amino acids concentrations in blood between individuals was significantly less than in the groups receiving whey protein or a mixture of amino acids. In other words, individual biochemical and physiological characteristics of individuals did not affect the assimilation of amino acids of hydrolysate.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

Online and offline shopping trip have different impacts on various aspects of urban life, such as e-commerce, transportation systems, and sustainability. Therefore, it is important to evaluate the factors that influence their choices. We use a hybrid machine learning model that combines a gray wolf optimization algorithm and a deep convolutional neural network to estimate shopping trip based on a survey of 1,000 active e-commerce users who made successful orders in both online and offline services in the last 20 days of 2021 in areas 2 and 5 of Tehran. The gray wolf optimization algorithm performs feature selection and hyperparameter tuning for the deep convolutional neural network, which is a powerful deep learning model for image recognition and classification. The results show that our model achieves an accuracy of 97.81% with an MSE of 0.325 by selecting seven out of ten features. The most important features are delivery cost, delivery time, product price, car ownership. In addition, comparing the performance of the proposed method with other methods showed that the proposed algorithm with an accuracy of 97.81%, the accuracies of the single deep learning model, MLP neural network, decision tree, and KNN models were 95.63%, 90.0%, 86.49%, and 80.16%, respectively.

Electric moped scooter sharing services have recently experienced strong growth rates, particularly in Europe. Due to their compactness, environmental-friendliness and convenience, shared e-mopeds are suitable modes of transport in urban mobility to help reduce the environmental impact. However, its traffic-related, economic and environmental effects are merely represented in academic research. We used passenger car traffic data in Berlin generated by the multi-agent transport simulation framework MATSim to develop a python-based simulation, resembling an e-moped sharing system. Based on the results, a total cost of ownership and a life cycle assessment for fleet sizes of 2,500, 10,000 and 50,000 vehicles were conducted. The results indicate that a substantial part of all passenger car trips in Berlin can be substituted. The larger the fleet, the more and longer trips are replaced. Simultaneously, the efficiency in terms of fleet utilization decreases. The scenario with 10,000 e-mopeds offers the lowest total distance-based costs for sharing operators, whereas a fleet consisting of 2,500 vehicles exhibits the lowest environmental emissions per kilometer driven over the expected lifespan of a shared e-moped. Based on the renewable energy potential for 2050 forecasted by the German Federal Environment Agency, a significant overall decline in environmental impacts can be achieved.

(1) Background: Double-strand breaks (DSBs) in a single nucleus are usually measured using the sperm chromatin structure assay (SCSA), sperm chromatin dispersion (SCD) test, and comet assay (CA). We developed mono-dimensional single-cell pulsed-field gel electrophoresis (1D-SCPFGE) and angle-modulated two-dimensional single-cell pulsed-field gel electrophoresis (2D-SCPFGE) to observe DNA fragmentation in separated motile sperm. (2) Methods: We set up comparative standards, calibration curves, the required sensitivity, and eligibility criteria for test sperm to validate their measurement principles. (3) Results: We revealed that the conventional methods overlooked the interference of nucleoproteins in their measurements. In-gel proteolysis improves the measurement accuracies of 1D- and 2D-SCPFGE. We recommend using naked DNA for comparative standards and test specimens. Moreover, we have observed several dysfunctions that may induce DNA damage in the separated motile sperm. Overall, our discussion highlights the need to revisit the conventional univariable analyses based on the SCSA, SCD test, and CA. (4) Conclusions: Human infertility is a complex syndrome, and the aim of quality control in intracytoplasmic sperm injection is to identify the underlying dysfunctions remaining in the separated motile sperm that render them ineligible for injection. Well-designed, multivariable analyses with special consideration to confounding factors are necessary in future cohort studies.

Improper sitting positions are known as the primary reason for back pain and the emergence of musculoskeletal disorders (MSD) among individuals who spend prolonged time working with computer screens, keyboards, and mice. At the same time, it is well understood that automated technological tools can play an important role in the process of unhealthy habit alteration, so plenty of research efforts are focused on research and technology development (RTD) activities that aim to provide support to the prevention of back pain or the development of MSD. Here, we report on creating a new resource in support of RTD activities aiming at the automated detection of improper sitting positions. It consists of multimodal multisensory recordings of 100 persons made with a video recorder, camera, and wrist-attached sensors that capture physiological signals (PPG, EDA, Skin temperature), as well as motion sensors (three-axis accelerometer). Our multimodal multisensory dataset (MMD-MSD) opens new opportunities for modeling the body stance (sitting posture and movements), physiological state (stress level, attention, emotional arousal, valence), and performance (success rate on the Stroop test) of people working with a computer. Finally, we demonstrate two use cases: improper neck posture detection from pictures and cognitive load detection from physiological signals.

In the last two decades, the development of high-throughput diagnostic methods and availabil-ity of effective treatments has increased interest in newborn screening for lysosomal storage disorders. However, long-term follow-up experience is needed to clearly identify risks, benefits and challenges. We report our 8-year experience of screening and follow up on about 250,000 neonates screened for four lysosomal storage diseases (Pompe disease, mucopolysaccharidosis type I, Fabry dis-ease, Gaucher disease), using enzyme activity assay by tandem mass spectrometry, and bi-omarker quantification as second tier test. Among the 126 positive newborns (0.051%), 51 infants were confirmed as affected (positive pre-dictive value 40%), with an overall incidence of 1:4,874. Of these, 3 infantile-onset Pompe dis-ease, 2 neonatal-onset Gaucher disease and 4 mucopolysaccharidosis type I patients were imme-diately treated. Furthermore, another four Gaucher disease patients needed treatment in the first years of life. Our study demonstrated the feasibility and effectiveness of newborn screening for lysosomal storage diseases. Early diagnosis and treatment allow the achievement of better patient out-comes. Challenges such as false positive rates, the diagnosis of variants of uncertain significance or late-onset forms, and the lack of treatment for neuronopathic forms, should be addressed.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

Alzheimer’s disease (AD) causes dementia and memory loss in the elderly. Deposits of beta-amyloid peptide and hyperphosphorylated tau protein are present in AD’s brain. A filtrate of Helicobacter pylori’s culture was previously found to induce hyperphosphorylation of tau in vivo, suggesting that bacterial exotoxins could permeate the blood brain barrier and directly induce tau’s phosphorylation. H. pylori, which infects ~60% of the world population and causes gastritis and gastric cancer, produces a pro-inflammatory urease (HPU). Here the neurotoxic potential of HPU was investigated in cultured cells and in rats. SH-SY5Y neuroblastoma cells exposed HPU (50-300 nM) produced reactive oxygen species (ROS) and had an increased [Ca2+]i. HPU-treated BV-2 microglial cells produced ROS, cytokines IL-1β and TNF-α, expressed Iba1 and showed reduced viability, consistent with a neurotoxic effect of HPU. Rats received daily i.p. HPU (5 µg) for 7 days. Hyperphosphorylation of tau at Thr205, Ser199 and Ser396 sites was seen in hippocampal homogenates of treated rats, with no alterations in total tau or GSK-3b levels. HPU was not detected in the brain homogenates. Behavioral tests were performed to assess cognitive impairments. Our findings support previous data suggesting an association between infection by H. pylori and tauopathies such as AD, possibly mediated by its urease.

Rainfall variability has resulted in extreme events like devastating floods and droughts which is the main cause of human vulnerability to precipitation in West Africa. Attempts have been made by previous studies to understand rainfall variability over Ghana but these have mostly focused on the major rainy season of April-July, leaving a gap in our understanding of the variability in the September-November season which is a very important aspect of the Ghanaian climate system. The current study seeks to close this knowledge gap by employing statistical tools to quantify variabilities in rainfall amounts, rain days, and extreme precipitation indices in the minor rainfall season over Ghana. We find extremely high variability in rainfall with a Coefficient of variation (CV) between 25.3% and 70.8%, and moderate to high variability in rain days (CV=14.0% - 48.8%). Rainfall amount was found to be higher over the middle sector (262.7 mm – 400.2 mm) but lowest over the east coast (125.2 mm – 181.8 mm). Analysis of the second rainfall season using the Mankandell Test presents a non-significant trend of rainfall amount and extreme indices (R10, R20, R99p, and R99p) for many places in southern Ghana. Rainfall Anomaly Indices show that the middle sector recorded above normal precipitation which is the opposite for areas in the transition zone. The result of this work provides a good understanding of rainfall in the minor rainfall season and may be used for planning purposes.

Autonomous unmanned aerial vehicles (UAVs) require highly reliable navigation information. Generally, navigation systems with the inertial navigation system (INS) and global navigation satellite system (GNSS) have been widely used. However, the GNSS is vulnerable to jamming and spoofing. The terrain referenced navigation (TRN) technique can be used to solve this problem. In this study, to obtain reliable navigation information even if a GNSS is not available or the degree of terrain roughness is not determined, we propose a federated filter based INS/GNSS/TRN integrated navigation system. we also introduce a TRN system that combines batch processing and an auxiliary particle filter to ensure stable flight of UAVs even in a long-term GNSS-denied environment. As an altimeter sensor for the TRN system, we use an interferometric radar altimeter (IRA) to obtain reliable navigation accuracy in high altitude flight. In addition, a parallel computing technique with general-purpose computing on graphics processing units (GPGPU) is applied to process a high resolution terrain database and a nonlinear filter in real time on board. Finally, we verify the performance of the proposed system through software-in-the-loop (SIL) tests and captive flight tests in a GNSS unavailable environment.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

Various factors, such as uncertainty of component parameters and uncertainty of sensor meas-urement values, contribute to the difficulty of fault detection in the landing gear retrac-tion/extension hydraulic system. In this paper, we introduce linear fractional transformation technology and uncertainty analysis theory for the construction of the diagnostic bond graph of the landing gear retraction/extension hydraulic system. In this way, interval analytical redundancy relations and fault signature matrix can be derived. Using the fault signature matrix, existing faults of the system can be preliminarily detected and isolated. Additionally, interval analytical re-dundancy relations can be used to detect system faults in detail, and cases analysis can be carried out to determine if the actuator is externally or internally leaky, and if the landing gear selector valve is reversing stuck. Compared to the traditional analytical redundancy relations, this method takes into account the negative factors of uncertainty; and compared to the traditional absolute diagnostic threshold, the interval diagnostic threshold is more accurate and sensitive.

: E-commerce sales surge represents a huge challenge for urban freight transport. Parcel lockers constitute a valid solution for addressing the challenges home deliveries imply. In fact, eliminating courier-consumer contact (also relevant for health-related issues, as made evident by COVID19 pandemic) and delivering in few predefined places might help coping with missed deliveries substantially. Furthermore, this option enables consolidated shipping and reducing delivery trip costs. This paper analyses and compares consumers’ preferences for alternative collection strategies. It investigates home delivery vs parcel locker use and forecasts their future market shares. This is performed based on both customers’ socio-economic variables and attributes characterising these alternative logistic fulfilment strategies. The case study considered rests upon a stated preference survey deployed in the city of Rome. The investigation specifically targets young people (i.e., population under 30 years) since they represent early adopters. Discrete choice models allow both quantifying the monetary value of parcel lockers attributes (i.e., willingness to pay measures) and estimating the potential demand for this innovative delivery scheme. Results show that distance and accessibility are the main choice determinants. Furthermore, there is an overall high propensity to adopt parcel lockers. This research can support policymakers when implementing such solutions.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

Investigations reporting positive effects of Extracorporeal Shock Wave Therapy (ESWT) on nerve regeneration are limited to the rat sciatic nerve model. The effects of ESWT on muscle-in-vein conduits (MVCs) have also not been investigated yet. This study aimed to evaluate the effects of ESWT after repair of the rat median nerve with either autografts (ANGs) or MVCs. In male Lewis rats, a 7-mm segment of the right median nerve was reconstructed either with an ANG or MVC. For each reconstructive technique, one group of animals received one application of ESWT while the other rats served as controls. Animals were observed for 12 weeks and nerve regeneration was assessed via computerized gait analysis, the grasping test, electrophysiological evaluations and histological quantification of axons, blood vessels and lymphatic vasculature. Here we provide for the first time a comprehensive analysis of ESWT effects on nerve regeneration in a rat model of median nerve injury. Furthermore, this study is among the first reporting the quantification of lymphatic vessels following peripheral nerve injury and reconstruction in vivo. While we found no significant direct positive effects of ESWT on peripheral nerve regeneration, results following nerve repair with MVCs were significantly inferior to those after ANG repair.

Nowadays, according to spectacular improvement in health care and biomedical level, a tremendous amount of data is recorded by hospitals. In addition, the most effective approach to reduce disease mortality is to diagnose it as soon as possible. As a result, data mining by applying machine learning in the field of diseases provides good opportunities to examine the hidden patterns of this collection. An exact forecast of the mortality after heart surgery will cause Successful medical treatment and fewer costs. This research wants to recommend a new stacking predictive model after utilizing the random forest feature importance method to foresee the mortality after heart surgery on a highly unbalanced dataset by using the most practical features. To solve the unbalanced data problem, a combination of the SVM-SMOTE over-sampling algorithm and the Edited-Nearest-Neighbor under-sampling algorithm is used. This research compares the introduced model with some other machine learning classifiers to ensure efficiency through shuffle hold-out and 10-fold cross-validation strategies. In order to validate the performance of the implemented machine learning methods in this research, both shuffle hold-out, and 10-fold cross-validation results indicated that our model had the highest efficiency compared to the other models. Furthermore, the Friedman statistical test is applied to survey the differences between models. The result demonstrates that the introduced stacking model reached the most accurate predicting performance after Logistic Regression.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

Background: Humoral memory and specific antibodies levels depend on kind of the antigen and individual immunofactors., The presence of IgM antibodies or fourfold rise in specific IgG level, are generally accepted as diagnostic in serology of acute viral infection. This basic model is not adequate for herpesvirome especially after hematopoietic stem cell transplantation (HSCT) due to continuous, usually multifocal antigenic stimulation, various donor serostatus, immunosuppresion and individual immunoreconstitution. Methods: A  case-control study was conducted for identifying cases of Human herpesviruses (HHV) active infection (from 300 diagnosed immunocompromised patients) and evaluating historically associated humoral factors to look at outcomes. We enrolled only patients’ data with meticulous differential diagnosis to exclude other causes, thereby observe pathways and temporal relationships, not statistical ones, usually collected in cohorts. Despite the small number such data collection and analysis avoids a number of biases and indicates cause and effect.Results. In the observational study retrospective analysis of data from 300 patients with clinical diagnosis of herpes simplex (HSV) and varicella zoster virus(VZV) reactivation showed a number of biases. In two well differentiated cases (confirmed by Tzanck test) with various disease and conditioning evolution of immunoparameters showed interesting pathway. Exponential decrease of specific IgG after HSCT precedes virus replication with cytopathic effect (shingles, VZV-encephalitis and HSV-induced mucositis). Minima (smallest IgG levels) before herpes virus reactivation were 234,23 mIU/ml and 94 RU/ml for VZV and HSV, respectively. This coincides with low CD4 titer, but without other infectious process. Other immune response parameters such as Treg, cytotoxic T cells, complement and total IgG level were quite the same as before the transplant procedure. Interestingly, the second wave of immunoreconstitution with anamnestic antibody response was not always observed. It coincided with prolonged herpes viral infection. Patient with lymphocyte depletion in conditioning showed earlier second wave of immunoreconstitution (6th vs 14th month) Conclusions: Typical for infancy kinetics of IgG level is unique after HSCT (the decline phase is first). Host-microbiome factors (i.e. HHV1-3 -serostatus) should be taken into account to predict risk of non-relapse mortality and survival after HSCT. The levels of specific antibodies help to predict the prognosis and improve the management. The lack of differentiation, assessor and confusing bias are the main obstacles in statistical HHV1-3 research. Such time-lapse case studies may be first to build evidence of a pathway and association between immunoparameters and HHV disease.

Nutrition, diabetes, and mental disorders are interconnected and significantly impact an individual's overall health and well-being. This comprehensive review aims to explore the complex interplay between nutrition, diabetes, and mental disorders, highlighting the latest research findings in this field. While the influence of nutrition on the development and management of both diabetes and mental disorders is widely recognized, there remains a gap in understanding the intricate interplay between nutrition, mental health, and diabetes. Diabetes is associated with an increased risk of mental disorders, including depression, anxiety, and cognitive decline. Mental disorders can also contribute to the development of diabetes through various mechanisms including increased stress, poor self-care behaviors, and adverse effects on glucose metabolism. Thus, the mechanisms linking nutrition, diabetes, and mental disorders are complex and multi-factorial. Inflammation, oxidative stress, gut microbiota alterations, and neuroendocrine dysregulation have emerged as potential pathways that may mediate the relationship between nutrition, diabetes, and mental disorders. Additionally, deficiencies in essential nutrients such as omega-3 fatty acids, vitamin D, B vitamins, zinc, chromium, magnesium, and selenium have been implicated in the pathogenesis of both diabetes and mental disorders. Our findings indicate that the use of personalized dietary interventions and targeted nutrient supplementation can improve metabolic and mental health outcomes in patients with type 2 diabetes.

Obesity in adolescents combined with the increased exposure time to electronic devices, enhances a sedentary lifestyle and is linked to the risk of developing musculoskeletal injuries. The aim of this study was to identify possible correlations between anthropometric characteristics, body composition, exposure time to electronic devices or screen time (ST) and physical activity (PA) level along with muscle power and dynamic knee valgus (DKV) in young athletes to avoid future injuries. A total of 125 adolescent basketball athletes (66.4% boys), 12 to 17 years old (13.94±1.58 years) participated. Anthropometric and demographic characteristics were recorded. PA level was assessed through IPAQ and ST through a single question from the HELENA study. The Counter Movement Jump test was used for the evaluation of the lower limb muscle power, while the Single Leg Drop Jump test was used for the evaluation of the dynamic knee valgus via two-dimensional (2D) kinematic analysis. The Pearson index showed a statistically significant positive correlation between muscle power and height (r=0.788, p<0.001), while the Spearman index showed a smaller but equally statistically significant positive correlation with BMI (rs =0.651, p<0.001) and age (rs=0.579, p<0.001). The ST (rs= -0.194, p=0.03) showed a weak negative correlation with DKV, while PA (r=0.85, p<0.001) showed a high, statistically significant, positive correlation. The anthropometric characteristics of adolescent athletes can determine their ability to produce muscle power. A high level of physical activity could play a key role in compensating and thus reducing the negative effects of high exposure to screen time on the dynamic knee valgus

Rodents are known to be reservoirs of Toxoplasma gondii and keep the parasite circulation in the environment. We conducted biomonitoring to assess the role of sylvatic rodents in maintaining T. gondii and to analyse the prevalence and seroprevalence of the parasite in seven wild rodent species. Rodents were collected in our study sites (woodland and open grasslands) located in northeastern Poland and dissected. We collected brain, spleen, blood and serum samples. We applied both molecular (PCR assay, nested-PCR assay) and serological (ELISA and agglutination tests) methods to indicate the best approach for application in the biomonitoring of T. gondii in small mammals. We screened samples from 95 individuals sing PCR assays and found no T. gondii DNA. The agglutination test showed no signal. We found antibodies against T. gondii in 6 sera samples out of 74 analysed (seroprevalence = 8.11% [4.0-17.1]). Our results confirm that rodents participate in the life cycle of T. gondii as reservoirs of this parasite in the sylvatic environment. However, biomonitoring should be performed with the ELISA tests to search for T. gondii antigens, rather than a molecular approach only.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

The core motivation for this study emanates from Voronin S.'s seminal work on the universality of the zeta function. This universality positions the zeta function as a pivotal element in the conceptual framework of global artificial intelligence, suggesting its potential as a foundational component. A critical barrier to harnessing this promising universality has been the absence of efficient algorithms capable of actualizing this concept.

Minerals are the chief constituents of rocks and they have varied properties such as surface area, surface charge, site densities etc. Hence, numerous interactions are bound to occur in the reservoir during rock-fluids (i.e., rock, crude oil and brine) interactions. This study seeks to assess the role of mineralogical composition on the wettability of Sandstone Rocks (SR) and Mineral Mixture (MM) using both Surface Complexation Modelling (SCM) and flotation test. From the considered sandstone rocks, both the experimental results and its simulated counterpart revealed that, the SR were preferentially hydrophilic. For the MM, when the mass fraction of the hydrophobic mineral was increased, the affinity of the MM became slightly hydrophobic and vice-versa. For the dominant sandstone reservoir rock minerals with predominantly negatively charged surfaces, negligible oil adsorption took place due the interfacial repulsive forces at the oil-brine and mineral-brine interfaces. For the MM with low calcite content, the wetting preference was influenced by the mineral with prominent surface area. Our developed model portrayed that the main mechanism for oil adhesion onto sandstone minerals was divalent cations bridging. Nonetheless, adhesion of carboxylate (&gt;COO-) onto the illite, montmorillonite and calcite sites also took place with the latter being more pronounced.

Pavement friction plays a crucial role in ensuring the safety of road networks. Accurately assessing friction levels is vital for effective pavement maintenance and management strategies employed by state highway agencies. Traditionally, friction evaluations have been conducted on a case-by-case basis, focusing on specific road sections. However, this approach fails to provide a comprehensive assessment of friction conditions across the entire road network. This paper introduces a hybrid clustering algorithm, namely the combination of density-based spatial clustering of applications with noise (DBSCAN) and Gaussian mixture model (GMM), to perform pavement friction performance rating across a statewide road network. A large, safety-oriented dataset is first generated by integrating network friction and vehicle crash data based on the attributes contributing possibly to friction related crashes. One-, two-, and multi-dimensional clustering analyses, respectively, are then performed to rate pavement friction. The Chi-square test is further employed to validate and identify the practical ratings. It is shown that by effectively capturing the hidden, intricate patterns within the integrated, complex dataset and prioritizing friction-related safety attributes, the hybrid clustering algorithm can produce pavement friction ratings that align effectively with the current practices of the Indiana Department of Transportation (INDOT) in friction management.

Fanconi anemia (FA) patients display an exacerbated risk of oral squamous cell carcinoma (OSCC) and precursor lesions at young ages, mainly at the oral cavity. As patients have defects in DNA repair mechanisms, standard-of-care treatments to OSCC such as radiotherapy and chemotherapy give rise to severe toxicities. New methods for early diagnosis are urgently necessary to allow treatments in early disease stages and achieve better clinical outcomes. We have conducted a prospective, longitudinal study whereby liquid biopsies from sixteen lesion/tumor-free patients were analyzed for the presence of mutations in cancer genes. DNA from saliva and plasma were sequentially collected and deep-sequenced, and the clinical evolution followed during a median time of around 2 years. In 9/16 FA patients we detected mutations in cancer genes (mainly TP53) with molecular allele frequencies (MAF) down to 0.07 %. Importantly, all patients having mutations and clinical follow-up data after mutation detection (n=6) developed oral precursor lesions or OSCC. Lead-time between mutation detection and tumor diagnosis ranged from 23 to 630 days. Strikingly, FA patients without mutations display significantly lower risk of developing precursor lesions or OSCC. Therefore, our diagnostic approach could help to stratify FA patients into risk groups, which would allow closer surveillance for OSCC or precursor lesions.

Identifying anti-spike antibodies that exhibit strong neutralizing activity against current dominant circulating variants and antibodies that are escaped by these variants have important implications in the development of therapeutic and diagnostic solutions as well as in improving understanding of the humoral response to SARS-CoV-2 infection. We characterized seven anti-RBD monoclonal antibodies for their binding activity, pairing capability and neutralization activity to SARS-CoV-2 and three variant RBDs (UK, SA and BR P.1) via lateral flow immunoassays. The results allowed us to group these antibodies into three distinct epitope bins. Our studies showed that two antibodies had broadly potent neutralizing activity against SARS-CoV-2 and these variant RBDs and that one antibody did not neutralize the SA and BR P.1 RBDs. The antibody escaped by the SA and BR P.1 RBDs retained binding activity to SA and BR P.1 RBDs but was unable to induce neutralization. Further, we demonstrated that the lateral flow immunoassay can be a rapid and effective tool for antibody characterization, including epitope classification and antibody neutralization kinetics. From these studies, the potential contributions of the mutations (N501Y, E484K and K417N/T) contained in these variants’ RBDs on antibody pairing capability, neutralization activity and therapeutic antibody targeting strategy are discussed.

Finding out how cells with the same genome change fates in differentiation commitment is a challenge of biology. We used MCF-7 breast cancer cells treated with the ErbB2 ligand heregulin (HRG), which induces differentiation, to address if and how the constitutive pericentromere-associated domains (PADs) may be involved in this process. PAD-specific repressive heterochromatin (H3K9me3) and active euchromatin (H3K4me3) marking, centromere (CENPA) labelling, qPCR, acridine-orange-DNA structural test, and microscopic image analysis were applied. We found a two-step DNA unfolding, at 15-20 min and 60 min after HRG treatment, coinciding with bi-phasic activation of the early response genes (c-FOS family) and two steps of critical phase transition which were revealed in transcriptome studies. In control, the distribution of PAD number and size displays a power-law scaling with a boundary at the nucleolus. PADs’ clustering correlates with centromere numbers. 15 min after HRG treatment, the unravelling of PADs occurs, coinciding with the first step of euchromatin unfolding. The second step is associated with transcription of long-non-coding-RNA from satellite III DNA. We hypothesize that splitting of the PAD clusters under the critical size threshold of the silencing domain abrupts position effect variegation. It allows the first genome transcription avalanche to occur, starting differentiation commitment.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

Conclusions: Our findings suggest that the NMS-E represents a valuable preoperative diagnostic tool for endometriosis, effectively correlating with the disease's severity and surgical outcomes. Incorporating the NMS-E into clinical practice could significantly enhance the management of endometriosis by addressing current diagnostic limitations and guiding surgical planning.

The term neurodegeneration with brain iron accumulation (NBIA) brings together a broad set of progressive and disabling neurological genetic disorders in which iron is deposited preferentially in certain areas of the brain. Among NBIA disorders, the most frequent subtype is pantothenate kinase-associated neurodegeneration (PKAN) caused by pathologic variants in the PANK2 gene codifying the enzyme pantothenate kinase 2 (PANK2). Nowadays, there are no effective treatments to stop the progression of these diseases. This review discusses the utility of patient-derived cell models as a valuable tool for the identification of commercial pharmacological or natural compounds for implementing polytarget precision medicine in PKAN. In the last years, several studies have described that PKAN patient-derived fibroblasts manifest the main pathological changes associated with the disease including intracellular iron overload. Interestingly, treatment of mutant cell cultures with various supplements such as pantothenate, pantethine, thiamine, L-carnitine, vitamin E, omega 3, and -lipoic acid improved all pathophysiological alterations in PKAN fibroblasts with residual expression of the PANK2 enzyme. The information provided by pharmacological screenings in patient-derived cellular models can help to optimize therapeutic strategies in individual PKAN patients.

The pH-related metabolic paradigm has rapidly grown in cancer research and treatment. In this contribution, this recent oncological perspective has been laterally for the first time in order to integrate neurodegeneration within the energetics of the cancer acid-base conceptual frame. At all levels of study, molecular, biochemical, metabolic and clinical, the intimate nature of both processes appears to be opposite mechanisms occurring at the far ends of a physiopathological intracellular pH/extracellular pH (pHi/pHe) spectrum. This wide-ranged original approach now permits an increase in our understanding of these opposite processes, cancer and neurodegeneration, and, as a consequence, allows to propose new avenues of treatment based upon the intracellular and microenvironmental hydrogen ion dynamics regulating and deregulating the biochemistry and metabolism of both cancer and neural cells. Under the same perspective, the etiopathogenesis and special characteristics of multiple sclerosis (MS) becomes an excellent model for the study of neurodegenerative diseases and, utilizing this pioneering approach, we find that MS appears to be a metabolic disease even before an autoimmune one. Also within this paradigm, several important aspects of MS, from mitochondrial failure to microbiota functional abnormalities, are analyzed in depth.

The aim of this report is to evaluate the segmental rib index (RI) from T1-T12 spinal level in mild and moderate idiopathic scoliosis (IS) curves of thoracic, thoracolumbar and lumbar type by gender. The relationship of segmental RI to the frontal plane radiological deformity presented as the Cobb angle and to the posterior truncal surface deformity presented as the scoliometric readings of Angle of Trunk Rotation (ATR) in these patients is also assessed. Any statistical significant rela-tionship of these parameters would be very important for biomechanical relations of the rib cage (RC) deformity presented as the rib hump deformity (RHD) and the deformity in the spine and it would thus provide valuable information about scoliogeny. The segmental rib index (RI) is presented in 83 boys and girls with mild and moderate IS. The measurements include the scoliometric readings for truncal asymmetry (TA), the Cobb angle assessment and the segmental RI from T1-T12. The statistical package SPSS 23 was used for statistical analysis. The TA is documented and the Cobb angle is presented by gender and curve type. The segmental RI of thoracic, thoracolumbar and lumbar curves are presented for the first time. The correlations of the segmental RI to surface deformity presented as the rib hump deformity (RHD) in all IS patients and particularly in thoracic curves, to Cobb angle by gender and age and the comparison of the segmental RI index of asymmetric but not scoliotic children to the scoliotic peers by curve (in thoracic, thoracolumbar, lumbar curves) in boys and girls are presented. The findings emphasize the significant protagonistic role of the thoracic asymmetry in relation to the spinal deformity mainly in girls for the thoracic and in boys for the thoracolumbar curves. The cut-off point of age of the examined scoliotics is 14 years, that is when the RI shows stronger correlation with the spinal deformity, namely when the thoracic deformity is decisively effective to the developing thoracic spinal deformity, in terms of Cobb angle. In summary, the results of this study provide aetiological implications for IS, as far as the role of thorax is con-cerned.

Cervical cancer is a worldwide public health problem with a high rate of illness and mortality among women. In this study, we proposed a novel framework based on Faster RCNN-FPN ar-chitecture for the detection of abnormal cervical cells in cytology images from cancer screening test. We extended the Faster RCNN-FPN model by infusing deformable convolution layers into the feature pyramid network (FPN) to improve scalability. Furthermore, we introduced a global contextual aware module alongside the Region Proposal Network (RPN) to enhance the spatial correlation between the background and the foreground. Extensive experimentations with the proposed deformable and global context aware (DGCA) RCNN were carried out using the cer-vical image dataset of “Digital Human Body" Vision Challenge from the Alibaba Cloud TianChi Company. Performance evaluation based on the mean average precision (mAP) and receiver operating characteristic (ROC) curve has demonstrated considerable advantages of the proposed framework. Particularly, when combined with tagging of the negative image samples using tra-ditional computer-vision techniques, 6-9% increase in mAP has been achieved. The proposed DGCA-RCNN model has potential to become a clinically useful AI tool for automated detection of cervical cancer cells in whole slide images of Pap smear.

Background: Cervical cancer prevention in regions with limited access to screening and HPV vaccination necessitates innovative approaches. This study explored the potential of a test-and-treat strategy using mRNA HPV tests to impact cervical cancer prevention in a high-prevalence HIV population. Methods: A cervical screening study was conducted at three South African hospitals involving 710 under-screened, non-pregnant women (25 to 65 years) without known cervical diseases. Cytology, HPV testing, colposcopy, and biopsies were performed concurrently. Histopathologists determined final histological diagnoses based on biopsy and LLETZ histology. mRNA-HPV-genotyping for 3 (16, 18, 45) to 8 (16, 18, 31, 33, 35, 45, 52, 58) high-risk types was performed on leftover liquid-based cytology material. The preventive potential of the test-and-treat approach was estimated based on published data, reporting the causative HPV types in cervical cancer tissue from South African women. Treatment was provided as needed. Results: HPV positivity rate more than doubled from 3-type (15.2%; 95% CI: 12.6-17.8) to 8-type mRNA (31.5%; 95% CI: 28.8-34.9) combinations, significantly higher among HIV-positive women. CIN3+ prevalence among HIV-positive women (26.4%) was double that of HIV-negative women (12.9%) (p&lt;0.01). The 6-type combination showed the best balance of sensitivity, specificity and treatment group size, and effectiveness to prevent cervical cancer. A 4-type combination (16, 18, 35, 45) could potentially prevent 77.6% (95% CI: 71.2-84.0) of cervical cancer burden by treating 20% and detecting 41.1% of CIN3 cases in the study group. Similarly, a 6-type combination (16, 18, 31, 33, 35, 45), treating 25% and including 62% of CIN3 cases, might prevent 85% of cervical cancer cases (95% CI: 79.6-90.6) among HIV-positive and negative women. Conclusion: Employing mRNA HPV tests within a test-and-treat approach holds huge promise for targeted cervical cancer prevention in under-screened populations. Testing for mRNA of the 6 highest-risk HPV types in this population and treating them all is projected to effectively prevent progression from CIN3 to invasive cervical cancer while reducing overtreatment in resource-constrained settings.