Hydrothermal carbonization of cellulose was examined at 240 ℃ for 1 h. Ammonium sulfate and thiourea were selected as the doping sources of inorganic nitrogen and organic nitrogen for the preparation of supercapacitor carbon. The effect of boric acid on the properties of the resulting hydrochar after KOH activation was examined. The results showed that the proportion of functional groups and the specific surface area of the activated hydrochar would be reduced after the addition of boric acid, and the pore-forming process of the micropores would be inhibited. The hydrochar obtained from the reaction of cellulose and organic nitrogen compounds had better pore size distribution and electrochemical properties after activation. The largest specific surface area (952.27 m2 g-1) was obtained when only thiourea was used as the only doping source. In the three-electrode system, the specific capacitance resulting activated hydrochar reached 236.25 F g-1 at a current density of 1 A g-1. After 20,000 cycles of charging and discharging at a current density of 10 A g-1, the capacitance retention rate reached 99.96%. Therefore, this study proves that the supercapacitor carbon with good electrochemical properties could be obtained by the direct reaction of cellulose with organic nitrogen compounds.

Two methods for Pd nanoparticle synthesis were explored with three different carbide-derived carbon (CDC) support materials of which one was nitrogen-doped. These materials were studied for oxygen reduction reaction (ORR) in 0.1 M KOH solution. The prepared CDC/Pd catalysts were characterized using TEM, XRD and XPS. Using these methods, we can observe the influence of support materials for one-pot synthesis methods as we use the standard citrate method and polyol method with polyvinylpyrrolidone (PVP) as a capping agent. Comparing the two methods N-doping of carbon material resulted in smaller nanoparticles only in the case of citrate synthesis, suggesting that the influence of support is weaker using polyol method. Citrate method on CDC1, which was predominantly microporous led to a higher degree of agglomeration and larger particle formation in comparison to CDC2 and CDC3 supports, which possessed higher degree of mesoporosity. Smaller Pd particle sizes were achieved using citrate and NaBH4 in comparison to the ethylene glycol-PVP method. CDC2 and CDC3 did not show significant difference suggesting that the N-doping did not have much of an influence on the ORR. Highest SA value was observed on CDC1/Pd_Cit, which could be attributed to formation of larger particles and agglomerates.

Urbanization is a dynamic process. At different stages of urbanization, polices of managing car-bon emissions should be adjusted. In this paper, two types of nighttime light data and statistical data of 68 cities in China from 2002 to 2021 are used to establish an urban development evalua-tion system comprising population, economy, construction, and society subsystems. Then, cities were categorized into expanding, contracting, and stable types to understand the uncertainty of urbanization's impact on carbon emissions. The main conclusions are as follows: (1) Integrated nighttime light data is used to extract built-up area boundaries, achieving an overall accuracy ranging from 68.75% to 98.4%, with kappa coefficients ranging between 0.60 and 0.94. (2) Ex-panding cities were concentrated in the eastern coastal regions, while contracting cities were mainly located in inland cities with traditional industries. Urban agglomerations in the Beijing-Tianjin-Hebei region, Yangtze River Delta region, and Chengdu-Chongqing metropolitan demonstrate synchronized characteristic of urbanization development. (3)Economy and con-struction have a greater impact on carbon emissions than population and society. For expanding cities, the focus of carbon emission governance should prioritize rational land use planning. Conversely, for contracting cities, emphasis should be placed on adjusting economic structures.

Potassium-oxygen batteries (KOBs) are a promising energy storage technology with high theoretical en-ergy density, low overpotential and long cycle life. Cathode microstructure plays a significant role in the electrochemical performance of KOB. In this article, hierarchical porosity was introduced to commer-cially available carbon paper cathodes by the thermal pretreatment in air at different pretreatment times. This pretreatment modifies the properties, such as, surface area, defects, oxygen functional groups etc. and it has been found to enhance the discharge capacity and it result in reduction of dis-charge overpotentials.

Recently, electrocatalysts for oxygen reduction reactions (ORRs) as well as oxygen evolution reactions (OERs) hinged on electrospun nanofiber composites have attracted wide research attention. Transition metal elements and heteroatomic doping are important methods used to enhance their catalytic performances. Lately, the construction of electrocatalysts based on metal-organic framework (MOF) electrospun nanofibers has become a research hotspot. In this work, bimetallic NixCoy-ZIF nanocrystals were synthesized in an aqueous solution, followed by NixCoy-ZIF/PAN electrospun nanofiber precursors, which were prepared by a simple electrospinning method. Bimetal (Ni-Co) porous carbon nanofiber catalysts doped with nitrogen, oxygen, and sulfur elements were obtained at high-temperature carbonization treatment in different atmospheres (Ar, Air, and H2S), respectively. The morphological properties, structures, and composition were characterized by SEM, TEM, SAED, XRD, and XPS. Also, the specific surface area of materials and their pore size distribution was characterized by BET. Linear sweep voltammetry curves investigated catalyst performances towards oxygen reduction and evolution reactions. Importantly, Ni1Co2-ZIFs/PAN-Ar yielded the best ORR activity, whereas Ni1Co1-ZIFs/PAN-Air exhibited the best OER performance. This work provides significant guidance for the preparation and characterization of multi-doped porous carbon nanofibers carbonized in different atmospheres.

Greenhouse gas (GHG) emissions from agriculture are significant contributors to global change. We experimentally manipulated biogeochemical control points of irrigation and nitrogen (N) to examine management strategies that could impact GHG flux, i.e., carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) and soil physiochemical changes over a growing season in an arid New Mexico sorghum (Sorghum bicolor (L.) Moench) cropping system. Sorghum is water and N efficient and amenable to environmental stress. Interrogating how crop systems perform in intense heat, aridity and ultraviolet stress of the southwestern US climate can inform future management in areas that produce more food currently, but that will undergo these stresses in the near future. Water was applied at regionally typical rates, or at ~30% below those rates. Timing N to plant needs may reduce N loss and N2O emissions, and we tested this hypothesis by adding equal amounts of fertilizer to all plots, with half receiving all fertilizer at planting versus plots fertilized at 50:50 planting and 30 days post-planting. Gas flux from soil was analyzed via FTIR. More biomass was harvested from the fully irrigated plots; N timing did not significantly affect biomass. Soil pH fluctuated throughout the season in response to both treatments. Carbon dioxide emissions significantly increased in fully irrigated plots through time. Methane uptake was depressed by full irrigation. Nitrous oxide flux was lower in split N plots, but N2O emissions were not impacted by reduced irrigation. These results suggest that arid adapted crops can maintain economically feasible yield, and biogeochemical monitoring within a growing season can help manage for GHG flux.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

The Green Deal for Europe aims to achieve climate neutrality by 2050 and sets a binding EU target of a 55% reduction in greenhouse gas emissions by 2030 compared to 1990 levels. The contributions of EU Member States to this target will be partly determined by the market through the EU Emissions Trading Scheme. For the remaining part of greenhouse gas emissions outside the EU Emissions Trading Scheme, the Effort Sharing Regulation sets binding national reduction targets. The paper applies an energy optimization model to analyze the ability of the Czech Republic to meet the climate targets. Given the high level of GHG emissions in 1990 and the significant reduction of GHG emissions in the 1990s, Czechia could achieve a 55% reduction by 2030. However, further decarbonization will be quite challenging.

Shutdown for just six days enables land plants to entirely fix CO₂ excess of +4 Gt C per yr. Rebuilding soil organic carbon (SOC) in worm-worked humus is the only practical carbon capture and storage (CCS) capable of freely offsetting annual anthropogenic emissions. A case is made to redirect all available resources towards proven, earthworm-based, organic husbandry. Priority is to safely combat mounting global threats due to irreversible species extinction, perilous climate change and deteriorating human wellbeing (mental/physical health). All three interlinked risks are underpinned by a relentless, yet largely ignored, critical loss of precious topsoil. A first step to topsoil recovery is vermi-composting all vegetable and animal ‘wastes’ for return to the field.

In this study, we report the antibacterial mechanisms of action of uniform silver nanoparticles (AgNPs) and decorated activated carbon nanocomposite (CAC-AgNPs) obtained using a green synthesis approach. The nanomaterials were characterized by ultraviolet-visible (UV-vis) absorption spectra and Fourier transform infrared (FTIR) spectra. The antibacterial activity of the as-prepared nanomaterials was evaluated against an array of bacterial strains by microdilution method, whereas their cytotoxicity profile was evaluated on Vero cells (human mammalian cells). The antibacterial mechanistic studies of active nanomaterials were carried out through bacterial growth kinetics, nucleic acid leakage test, and catalase inhibition assay. A silver nanocomposite was successfully fabricated from Croton macrostachyus-based activated carbon. The as-prepared nanomaterials exhibited antibacterial activity against an array of bacterial strains (minimum inhibitory concentration (MIC) range: 62.5 to 500 µg/mL), the most susceptible being Escherichia coli and Staphylococcus aureus. Cytotoxicity studies of the nanomaterials on Vero cells revealed that the nanocomposite (median cytotoxic concentration (CC50): 213.6 µg/mL) was less toxic than the nanoparticles (CC50 value: 164.75 µg/mL) counterpart. Antibacterial mechanistic studies unveiled that the nanomaterials induced (i) bacteriostatic activity vis-à-vis E. coli and S. aureus and (ii) inhibition of catalase in these bacteria. This novel contribution on the antibacterial mechanisms of action of silver nanocomposite from C. macrostachyus-based activated carbon might contribute to the understanding of antibacterial action of these biomaterials. Nevertheless, more chemistry and in vivo experiments, as well as in depth antibacterial mechanistic studies are warranted for the successful utilization of these antibacterial biomaterials.

This study presents a novel polyurethane-activated carbon composite (PACC) as an effective and sustainable adsorbent for treating lead-ion-contaminated waters. The PACC was characterized using SEM-EDX, FTIR, BET, XRD, and TGA to evaluate its physicochemical and thermal properties. Furthermore, the PACC was employed in an experimental column adsorption setup to investigate its adsorption performance and to develop a dynamic method suitable for industrial implementation. Parameters such as bed height (50, 100, 150 mm), flow rate (4, 6, 8 mL min-1), pH (2, 4, 6), and initial metal ion concentrations (10, 50, 100 mg L-1) were examined. The experimental data exhibited strong agreement with the Thomas and Yoon-Nelson models (R2 ≥ 0.96), indicating efficient adsorption mechanisms. Remarkably, the depleted adsorbent has the potential for facile regeneration without substantial loss in capacity. The PACC demonstrated excellent adsorption performance for lead ions in aqueous solutions in a fixed-bed column system. Thus, the novel PACC material holds potential for scalable application in industrial settings to address water pollution challenges, especially in regions with uncontrolled effluent discharge.

With the aim of profitable conversion of carbon dioxide (CO2) in an efficient, economical and sustainable manner, we developed a CuBr/ionic liquid (1-butyl-3-methylimidazolium acetate) catalytic system which could efficiently catalyze the three-component reactions of propargylic alcohols, 2-aminoethanols, and CO2 to produce 2-oxazolidinones and α-hydroxy ketones. Remarkably, this catalytic system employed lower metal loading (0.0125-0.5 mol%) but exhibited the highest turnover number (2960) ever reported, demonstrating its excellent activity and sustainability. Moreover, our catalytic system could efficiently work under 1 atm of CO2 pressure and recycle among the metal-catalyzed systems.

Capturing and storing CO2 (CCS) was once regarded as a significant, urgent, and required option for reducing the emissions of CO2 from coal and oil and gas industries and mitigating the serious impacts of CO2 on the atmosphere and the environment. This recognition came about as a result of extensive research conducted in the past. The CCS cycle comes to a close with the last phase of CO2 storage, which is accomplished primarily by the adsorption of CO2 in the ocean and injection of CO2 subsurface reservoir formation, in addition to the formation of limestone by the process of CO2 reactivity with reservoir formation minerals through injectivities. CCS is the last stage in the carbon capture and storage (CCS) cycle and is accomplished chiefly via oceanic and subterranean geological sequestration, as well as mineral carbonation. The injection of supercritical CO2 into geological formations disrupts the sub-surface's existing physical and chemical conditions; changes can occur in the pore fluid pressure, temperature state, chemical reactivity, and stress distribution of the reservoir rock. This paper aims at advancing our current knowledge in CO2 injection and storage systems particularly CO2 storage methods and the challenges encountered during the implementation of each method and analyses on how key uncertainties in CCS can be reduced. CCS sites are essentially unified systems; yet, given the scientific context, these storage systems are typically split during scientific investigations based on the physics and spatial scales involved. Separating the physics by using the chosen system as a boundary condition is a strategy that works effectively for a wide variety of physical applications. Unfortunately, the separation technique does not accurately capture the behaviour of the larger important system in the case of water and gas flow in porous media. This is due to the complexity of geological subsurface systems, which prevents the approach from being able to effectively capture the behaviour of the larger relevant system. This consequently gives rise to different CCS technology with different applications, costs and social and environmental impacts. The findings of this study can help improve understanding of selecting a suitable CCS application method and can further improve the efficiency of greenhouse gas emissions and their environmental impact, promoting the process sustainability and helping to tackle some of the most important issues that human being is currently accounting global climate change. Though this technology has already had large-scale development for the last decade, some issues and uncertainties are identified. Special attention was focused on the basic findings achieved in CO2 storage operational projects to date. The study has demonstrated that though a number of CCS technology has been researched and implemented to date, choosing a suitable and acceptable CCS technology is still daunting in terms of its technological application, cost-effectiveness and socio-environmental acceptance.

Carbon subsurface storage (CSS) has already been recognised as a critical, urgent, and essential method for reducing anthropogenic CO2 emissions and mitigating the severe effects of climate change. CSS is the last stage in the carbon capture and storage (CCS) cycle and is accomplished chiefly via oceanic and subterranean geological sequestration, as well as mineral carbonation. The injection of supercritical CO2 into geological formations causes a disruption in the subsurface's existing physical and chemical conditions; changes can occur in the pore fluid pressure, temperature state, chemical reactivity, and stress distribution of the reservoir rock. This paper aims to present a comprehensive review on the current advances in CSS, particularly CO2 storage methods and the challenges encountered during the implementation of each methods and analyses on how key uncertainties in CSS can be reduce. CSS sites are essentially unified systems; yet, given the scientific context, these systems are typically split during scientific investigations based on the physics and temporal/spatial scales involved. Separating the physics by using the system as a boundary condition is a strategy that works effectively for a wide variety of physical applications. Unfortunately, the separation technique does not accurately capture the behaviour of the larger important system in the case of water and gas flow in porous media. This is due to the complexity of geological subsurface systems, which prevents the approach from being able to effectively capture the behaviour of the larger relevant system. This consequently give rise to different CSS methods. A good CSS application method can further improve the efficiency of greenhouse gas emission and their environmental impact, promoting the process sustainability and helping to tackle some of the most important issues that human being is currently accounting, global climate change. Though this technology is already large-scale development for the last decade, some issues and uncertainties are identified. Special attention was focused on the basic findings achieved in CO2 storage operational projects to date.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

Forests play an important role in reducing greenhouse gases in the atmosphere, thereby mitigating the impact of climate change. Estimating the accumulated biomass in a forest ecosystem is important for assessing the productivity and sustainability of the forest. Allometric models for above ground biomass (AGB) are linear regression equations based on the relationships between biomass and diameter at breast height (DBH), tree height (H), and/or wood density. This study estimates AGB in the Colo-I-Suva Forest Park by applying the allometry of Chave et al (2005) and the diameter: height ratio derived from Payton & Weaver (2011) for height estimation in a plot of 20

For every three people on the planet there is approximately two Tonne (Te) of available plastic waste. We show that carbon recovery from polystyrene (PS) plastic is enhanced by the co-addition to solvents to grow carbon nanotubes (CNTs) by liquid injection chemical vapour deposition. Polystyrene was loaded up to 4 wt% in toluene and heated to 780 °C in the presence of a ferrocene catalyst and a hydrogen/argon carrier gas in a 1:19 ratio. High resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Raman spectroscopy were used to identify multi-walled carbon nanotubes (MWCNTs). The PS addition in the range from 0 to 4 wt% showed improved quality and CNT homogeneity; Raman “Graphitic/Defective” (G/D) values increased from 1.9 to 2.3; mean CNT diameters increased from 43.0 to 49.2 nm; and maximum CNT yield increased from 11.3% to 14.2%. Since both the CNT diameters and the percentage yield increased with respect to polystyrene addition, we conclude that carbon from the PS contributes to the carbon within the MWCNTs. The electrical contact resistance of acid washed Bucky papers produced from each loading, ranged from 2.2 to 4.4 Ohm, with no direct correlation to PS loading. Due to this narrow range, the materials with different loading were mixed to create six wires of an Ethernet cable and tested using iPerf to give uplink and downlink speeds of ~99.5 Mbps, comparable to Cu wire of identical dimension (~99.5 Mbps). The lifecycle assessment (LCA) of CNT wire production was compared to copper wire production for the use case in a Boeing 747-400 over the lifespan of the craft. Due to their lightweight nature the CNT wires decreased the CO2 footprint by 21 kTonne (kTe) over the aircraft lifespan.

Nanoparticles (NPs) have various applications in medicine, cosmetics, optics, catalysis, environmental purification, and other areas nowadays. With an increasing annual production of NPs, the risks of their harmful influence to the environment and human health is rising. Currently, our knowledge about the mechanisms of interaction between NPs and living organisms is limited. Additionally, poor understanding of how physical and chemical characteristic and different conditions influence the toxicity of NPs restrict our attempts to develop the standards and regulations which might allow us to maintain the safe living conditions. The marine species and their habitat environment are under continuous stress due to anthropogenic activities which result in the appearance of NPs in the aquatic environment. Our study aimed to evaluate and compare biochemical effects caused by the influence of different types of carbon nanotubes, carbon nanofibers, and silica nanotubes on four marine microalgae species. We have evaluated the changes in growth-rate, esterase activity, membrane polarization, and size changes of microalgae cells using flow cytometry method. Our results demonstrated that toxic effects caused by the carbon nanotubes strongly correlated with the content of heavy metal impurities in the NPs. More hydrophobic carbon NPs with less ordered structure had a higher impact on the red microalgae P. purpureum because of higher adherence between the particles and mucous covering of the algae; silica NPs caused significant inhibition of microalgae growth-rate predominantly produced by mechanical influence.

A flexible asymmetric supercapacitor (ASCs) is successfully developed by using the composite of MoO3 and graphene oxide (GO) electrochemically deposited on carbon cloth (CC) (MoO3/rGO/CC) as the negative electrode, the MnO2 deposited on CC (MnO2/CC) as the positive electrode and Na2SO4/polyvinyl alcohol (PVA) as gel electrolyte. The results show that the introduction of GO layer can remarkably increase the specific capacitance of MoO3 from 282.7 F g-1 to 341.0 F g-1. Furthermore, the combination of such good electrode materials and a neutral gel electrolyte renders the fabrication of high-performance ASC with a large operating potential difference of 1.6 V in 0.5 mol L-1 Na2SO4 solution of water. Furthermore, the ASCs exhibit excellent cycle ability and the capacitance can maintain 87 % of its initial value after 6000 cycles. The fact that a light-emitting diode can be lighted up by the ASCs indicates the device’s potential applications as energy storage devices. The encouraging results demonstrate a promising application of the composite of MoO3 and GO in energy storage devices.

This review focuses on an extensive synopsis of the recent improvements in the field of CO2 hydrogenation over structured zeolites including their properties, synthesis methods, and characterization approaches. The role of bimodal mesoporous structures surface oxygen vacancies, and the Si/Al ratio in improving catalytic activity is highlighted. The porosity, thermal stability, and structural integrity are also discussed in the review along with how structured zeolites are affected by electrical and plasma interactions. The synthesis methods are analyzed in detail by comparing the benefits and drawbacks of the bottom-up techniques, such as hard templating, soft templating, and non-templating on the one side; and the top-down approaches, e.g. dealumination, desilication, and recrystallization on the other. This review also draws attention to the necessity of overcoming the difficulties arising from these synthesis techniques, for example, micropore-induced diffusion restrictions and morphological constraints, employing innovative approaches and optimization strategies. Conventional and advanced characterization techniques are pointed out in this respect as crucial for understanding the catalytic mechanism and the dynamic behavior, hence, beneficial in the advancements of research on structured zeolites with higher efficiency and activity. The review ends with a perspective that highlights the necessity of further research in the improvement of synthesis approaches and characterization procedures of the structured zeolites to increase their catalytic activity in CO2 hydrogenation, a critical process of paramount importance in the global effort to reduce excessive carbon emissions and combat climate change..

Smoked cigarette butts (SCB) can be used as precursors to obtain activated carbon (AC) due to their high carbon content related to the presence of cellulose acetate and components that are retained in the tobacco combustion process. In this way, it was analyzed how the process of pyrolysis or formation of char from this residue occurs, for this a study of the kinetics of formation of char is carried out by thermogravimetry, using three heating speeds 5, 10 and 15 °C/min. Based on the data obtained, mathematical models such as Kissenger - Akahira - Sunose (KAS), Starink (STK) and Ozawa - Flynn - Wall (OFW) were used in order to identify thermodynamic parameters through the energy of activation. The char obtained was subjected to an activation treatment with KOH in order to increase the surface area and pore volume, obtaining values of 433 m2/g of BET area and 0.25 cm3/g of micropore volume. Finally, the adsorbent was applied in the removal of Cr (VI) obtaining a Qmax capacity determined by the Langmuir model of 55.8 mg/g.

A series of supported CuO-based nanoparticle catalysts were prepared by impregnation method and used for the synthesis of glycerol carbonate from glycerol and CO2 in the presence of 2-cyanopyridine as a dehydrant and DMF as a solvent. The effects of supports (activated alumina, silicon dioxide, graphene oxide, graphene, and activated carbon), CuO loading amount, calcination temperature, and reaction parameters on the catalytic activity of catalyst were investigated in detail. XRD, FTIR, SEM, BET, and CO2-TPD were used for the characterization of the prepared catalysts. It is found that CuO/Al2O3 shows a higher catalytic activity, which depends on the CuO loading amount and calcination temperature. The surface area and amount of basic sites of the catalyst exhibit crucial effect on the catalytic activity of CuO/Al2O3. Furthermore, there is a synergistic effect between the catalyst and 2-cyanopyridine that the former has higher activation ability for glycerol and the latter acts not only as a dehydrant, but also as a promoter for CO2 activation. Recycling experiments reveal that this catalyst can be reused at least five cycles without any inactivation. Based on the experiment results and FTIR characterization, a possible reaction mechanism for the carbonylation of glycerol and CO2 is proposed.

Ecological footprint calculators are digital tools that help individuals calculate their environmental or climate impact, with the aim of stimulating pro-environmental behaviour change. These footprint calculators typically take an information-provision approach, but this strategy assumes that increased levels of knowledge result in increased levels of pro-environmental behaviour (i.e., a reduced footprint). This is not a given – existing literature on the relationship between environmental knowledge and pro-environmental behaviour is inconclusive, and this relationship may be different from that of environmental knowledge and ecological footprint. As such, we investigated the relationship between environmental knowledge and ecological footprint as estimated by a footprint calculator. 448 Dutch participants completed an online survey, including an ecological footprint calculator. We found no evidence for a relationship between environmental knowledge and ecological footprint calculator outcome. Rather, an exploratory analysis of our data showed that environmental values were more important predictors of ecological footprint. The finding that increased levels of knowledge are not related to a reduced ecological footprint suggests that calculators would do well to move beyond information provision, and employ additional behaviour change strategies. Based on our exploratory analysis, we provide several concrete examples of potential strategies.

In this study, a new nitrogen-enriched multiwall carbon nanotube is prepared and utilized to stabilize palladium species. After the characterization of this new composite, it was applied as a catalyst in the reduction of nitroarenes and hydrodesulfurization of dibenzothiophene. Using this newly established catalyst, a wide range of aromatic compounds were reduced to the corresponding amines under a very low amount of Pd (0.005 mol%) in short reaction times. Also, dibenzothiophene (a major pollutant in fuel oil) was very efficiently transformed using this catalyst. Its robustness was studied in the recycling process where, after 20 runs in the reduction of 4-nitrotoluene and 5 times in the desulfurization of dibenzothiophene, the activity of the catalyst remained intact. According to the E-factor calculations, the present Pd catalyst meets the standards of green chemistry.

Continuous cropping of Platycodon produces problems that significantly impact its yield and quality making it a pressing issue that requires immediate attention. In this study, the sandwich method is employed to evaluate the allelopathic activity of different plant parts (leaves, stems, and roots) of Platycodon. The inhibitory effects of the various Platycodon plant parts were quantified based on their effects on lettuce seedlings growth by Sandwich method, with the following average inhibition percentages at 1 mg/ml (agar) of : leaves (79.4%, 61.8%), stems (58.0%, 45.7%), and roots (53.4%, 49.3%) for lettuce radicals and hypocotyls, respectively. At a concentration of 5 mg/ml, the inhibitory effects were as follow: leaves (91.9%, 72.2%), stems (79.5%, 60.3%), and roots (71.4%, 65.2%). Also, by employing the Plant Box method, it was determined that Platycodon root exudation. The growth inhibition rates of lettuce seedling roots and hypocotyls were 45.5% and 18.9%, respectively. The effect of activated carbon on the adsorption of allelopathic substances was investigated, and the results of the sandwich method with a concentration of 1 mg/ml showed the following growth inhibitory effects on lettuce seedlings and hypocotyls: roots (27.8%, 25.7%), leaves (13.3%, 25.7%), and stem (9.07%, 13.6%). The Plant Box method revealed average rates of inhibition of -16.7% and -4.70% on the growth of lettuce seedlings and hypocotyls, respectively. The results of this study demonstrated that activated carbon has a mitigating effect on the allelopathic inhibition associated with the different plant parts and root exudation of Platycodon, thus may provide a potential solution for overcoming obstacles associated with continuous cropping of Platycodon.

Carbon fiber insole (CFI), which is lightweight and stiff to reduce energy loss and help wearers perform better in sports, has recently been introduced. However, there are scarce reports on the effects of CFI on sports performance, muscle fatigue and wearing comfort. This study investigat-ed the short-term effects of CFI on sports performance, lower extremity muscle activity, and sub-jective comfort. Thirty young healthy males performed various sports tasks and treadmill runs with wearable sensors under two experimental insole conditions (benchmark insole as a baseline, CFI). The results showed that compared to the benchmark insole, CFI significantly improved sports performance in terms of power generation and agility. However, it activated more of the Tibialis Anterior and Gastrocnemius Medialis muscles and was perceived stiffer, and less com-fortable. These findings suggested that CFI can improve sports performance, but it could cause more lower extremity muscle fatigue and subjective discomfort.

.Functionalization of multi-walled carbon nanotubes (MWNTs) surface with sulfonated poly(ether ether ketone) SPEEK chains using hexane diamine (HAD) as the interlinking molecule was investigated. MWNTs were first oxidized by nitric acid to generate carboxyl groups on their surface. Grafting of SPEEK chains on the MWNTs surface was achieved using hexane diamine as a cross-linking molecule. The attachment took place after the reaction of amine groups with carboxyl groups of oxidized MWNTs and sulfonate groups of SPEEK as confirmed by infrared (FTIR) analysis. Scanning electron microscopy (SEM) showed that MWNTs were packed into a dense and compact structure. Transmission electron microscopy (TEM) showed that the nanotubes were wrapped by polymer chains and arranged in a bundle like structure. These observations reveal that some of MWNTs were interconnected by SPEEK chains.

Herein, we present a combination of experimental and computational study on the mitochondrial F0F1-ATPase nanotoxicity inhibition induced by single-walled carbon nanotubes (SWCNT-pristine, SWCNT-COOH). To this end, the in vitro inhibition responses in submitochondrial particles (SMP) as F0F1-ATPase enzyme were strongly dependent on the concentration assay (from 3 to 5 µg/ml) for both types of carbon nanotubes. Besides, both SWCNTs show an interaction inhibition pattern like the oligomycin A (the specific mitochondria F0F1-ATPase inhibitor). Furthermore, the best crystallography binding pose obtained for the docking complexes based on the free energy of binding (FEB), fit well with the previous in vitro evidences from the thermodynamics point of view. Following an affinity order as: FEB (oligomycin A/F0-ATPase complex) = -9.8 kcal/mol > FEB (SWCNT-COOH/F0-ATPase complex) = - 6.8 kcal/mol ~ FEB (SWCNT-pristine complex) = -5.9 kcal/mol. With predominance of van der Waals hydrophobic nanointeractions with key F0-ATPase binding site residues (Phe 55 and Phe 64). By the other hand, results on elastic network models, and fractal-surface analysis suggest that SWCNTs induce significant perturbations by triggering abnormal allosteric responses and signals propagation in the inter-residue network which could affect the substrate recognition ligand geometrical specificity of the F0F1-ATPase enzyme in order (SWCNT-pristine > SWCNT-COOH). Besides, the performed Nano-QSTR models for both SWCNTs show that this method may be used for the prediction of the nanotoxicity induced by SWCNT. Overall, the obtained results may open new avenues toward to the better understanding and prediction of new nanotoxicity mechanisms, rational drug-design based nanotechnology, and potential biomedical application in precision nanomedicine.

Increase in the emission of Greenhouse Gases (GHS) is among the significant concerns of government, societies, and policymakers. Due to the highest share of carbon dioxide in the produced GHGs, it is necessary to assess the factors that influence its emission. Energy systems and economic activities noticeably influence the amount of carbon dioxide production of countries. In this article, Artificial Neural Network (ANN) in addition to a linear correlation used to predict carbon dioxide emission of four CIS countries, including Turkmenistan, Uzbekistan, Kazakhstan, and Azerbaijan based the consumption of various energy sources and GDP, as the economic indicator. According to the obtained data by the proposed models, carbon dioxide emission can be accurately estimated by utilizing the mentioned input data. Models’ R-squared value are 0.9997 and 0.9999 in the cases of applying the correlation and ANN-based model. Moreover, the average absolute relative deviations by utilizing the correlation and GMDH ANN are approximately 1.05% and 0.61%, respectively. These statistical values demonstrate more proper performance of the ANN-based model compared with the applied linear correlation.

Amid urgent global climate and biodiversity crises, the strategic restoration of degraded forests stands as a vital countermeasure. This study pioneers a novel approach for the identification and prioritization of potential degraded forest areas suitable for restoration (PDFR), utilizing the advancements in Earth observation data. Utilizing Landsat data within the Google Earth Engine, our PDFR method applies a nuanced, phenology-based threshold classification to accurately map forest covers at a 30-m resolution, distinguishing prime restoration areas such as evergreen, semi-evergreen, deciduous, and flooded forests, and categorizing them into varying levels of degradation using Siem Reap, a province in Cambodia as a case study. The projections indicate a promising potential for carbon sequestration through restoration of the critically (~96,693 ha), highly (48,878 ha), moderately (46,487 ha), and slightly degraded (75,567 ha) forests, estimating a capture of 193.73 TgCO2 in Siem Reap from 2021 to 2030 upon comprehensive restoration initiatives. As Earth observation technologies continue to evolve, the PDFR method emerges as a strategic blueprint for data-driven policy formulation, fostering sustainable forest management and aligning with the global commitments delineated in the Glasgow Forests Declaration for 2030.

This retrospective study evaluates the effect of a telemedicine program developed in the central Catalan region in lowering the environmental footprint by reducing the emission of atmospheric pollutants thanks to a reduction in the number of hospital visits involving journeys by road. Between January 2018 and June 2019 a total of 12,322 referrals were made to telemedicine services in the primary care centers, avoiding a total of 9,034 face-to-face visits. In total, the distance saved was 192,682 km, with a total travel time savings of 3,779 hours and a total fuel reduction of 11,754 liters with an associated cost of €15,664. This represents an average reduction of 3,248.3 g of carbon dioxide, 4.05 g of carbon monoxide, 4.86 g of nitric oxide and 3.2 g of sulphur dioxide. This study confirms that telemedicine reduces the environmental impact of atmospheric pollutants emitted by vehicles, reducing the number of journeys made for face-to-face visits and can contribute to environmental sustainability.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

To promote low-carbon and green travel, this study proposes a tripartite evolutionary game model among new energy vehicle manufacturers, consumers, and government agencies. The game strategy combinations of each party and the stability conditions of the equilibrium point in the evolutionary game system are analyzed, and the validity of the conclusions is verified through simulation results. The study shows a strong correlation between the three parties in the evolutionary game system. From the perspective of car manufacturers, the probability of producing new energy vehicles is positively proportional to the subsidy received from new energy policy, the additional revenue gained from the management of the carbon trading scheme, and the fine received for producing conventional fuel vehicles. However, from the consumer perspective, the likelihood that consumers purchase new energy vehicles is positively related to the utility value to consumers and the coverage of public charging points in the city, and inversely related to the sales price of new energy vehicles. From the government perspective, a combination of direct subsidy policies and indirect support strategies should be considered to stimulate the rapid development of the new energy vehicle industry.

High-rise buildings represent technological, urban and life-style trends of the modern urban landscape, yet there are limited data regarding their embodied carbon and environmental impacts, particularly when compared to low- or mid-rise buildings. Given that the projected growth of the global urban population by 2050 requires cities with higher density and potentially greater number of high-rise buildings, it is crucial to develop a clear understanding of the embodied carbon and environmental impacts of high-rise buildings. This article utilizes the building in-formation modelling (BIM) based life cycle assessment (LCA) in Revit and Tally to examine the embodied carbon and environmental impacts of an actual high-rise building structure case-study in Chicago that uses hybrid concrete steel structure. The results show that the embodied carbon and environmental impacts of the high-rise building structure are dominated by the impacts of the product stage in the building life cycle, and concrete as the main structural material. Specifically, this study reveals that concrete constitutes a substantial 91% share of the total mass of the building structure, with 74% contribution to life cycle global warming potential, 53% to acidification po-tential, 74% to eutrophication potential, 74% to smog formation potential, and 68% to non-renewable energy. On the other hand, steel accounts for 9% of the building structure mass, estimated to constitute 26% of the global warming potential, 47% to acidification potential, 26% to eutrophication potential, 26% to smog formation potential, and 32% to non-renewable energy.

The climate change is likely to modify the freezing-thawing cycles in soils and surface waters of permafrost-affected and subarctic regions. Yet, the change of solution chemical composition during ice formation and evolution of remaining fluids remain very poorly known. Towards better understanding of dissolved (< 0.45 µm) organic carbon, major and trace elements behavior in permafrost peatland environments, here we performed laboratory freezing of peat leachates, from complete freezing to complete thawing in order to quantify the partitioning of solutes between the aqueous solution and the remaining ice. We hypothesized the existence of two main groups of solutes, behaving conservatively or non-conservatively during freezing depending on their incorporation into the ice or ability to coagulate in the form of insoluble minerals or amorphous materials in the fluid phase. An unexpected result of this work was that, despite sizable degree of element concentration in the remaining fluid and possible coagulation of organic, organo-mineral and inorganic compounds, the freezing and subsequent thawing produced the final concentrations of most solutes which were not drastically different from initial concentrations in starting leachates, prior freezing. This demonstrates high stability of dissolved (< 0.45 µm) OC, Fe, Al and some trace metals to repetitive freezing and thawing of surface waters in permafrost peatlands.

Recent developments in high-performance electrode materials have been pivotal for real-time monitoring biosensors, necessitating compatibility with biomaterials and robust electrochemi-cal properties. This study explores the development of electrode materials using single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs), with a primary fo-cus on assessing their dispersion and electrochemical properties. Various solvents, including N N-Dimethylformamide (DMF), deionized water, ethanol, and acetone, were used for dispersion analysis by employing ultrasonic waves. The results showed that SWCNTs exhibited well-dispersed characteristics without precipitation when introduced to a DMF solution. It found that resistance values decreased as the concentration of SWCNTs increased over the range of 0.025 to 0.4 g/L, with a considerable electrical conductivity reached at concentrations ranging from 0.2 g/L to 0.4 g/L in DMF. The biosensor platform was evaluated with 1-pyrenebutanoic acid succin-imidyl este (PBSE) as the linker and glucose oxidase (Gox) and chitosan as the binding substrate. The binding of Gox with glucose resulted in a significant decrease in resistance value of the biosensor with rising their concentrations ranged from 0.001 to 0.1 M. Though this research provides founda-tional insights for the advancement of SWCNT-based high-performance electrode materials, it will pave the way for the next generation of efficient and reliable biosensors.

The current work shows the optimization in the preparation of nanosized titanium carbide (TiC) in-situ through mechanical alloying (MA). Metallic titanium (Ti) powders, along with two carbon sources, carbon nanotubes (CNTs), and stearic acid (SA), were used to reduce the particle size using a high-energy Spex800 mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent (PCA) proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4-hour timeframe. The use of 20 wt % of both carbon sources was compared to determine the ability of CNTs to form carbides and the decomposition of PCAs during mechanical milling. The result reveals structures like nanoblocks and nanolumps with and important size reduction. The structure and morphology of the composites and starting materials were evaluated through x-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

Cadmium(II) contamination in the environment is an emerging problem due to its acute toxicity and mobility, so it is very urgent to remove this species from industrial wastewater before it is discharged into the environment. Thus, a starch-based activated carbon (AC) with a specific surface area of 1600 m2g-1 is used as an adsorbent for the capturing of toxic cadmium(II) ions from synthetic solutions. The sorbent is characterized by BET, SEM, TEM, XRD, FT-IR, TGA, and zeta potential. The maximum uptake (284 mg g-1) of Cadmium(II) ion is obtained at pH 6. The thermodynamic parameters like ∆G, ∆H, ΔS are found to be -17.42 kJmol-1, 6.49 kJ mol-1, and 55.66 Jmol-1K-1 respectively, revealing that the adsorption mechanism is endothermic, spontaneous, and feasible. The experimental data follows the D-R and Langmuir models well. The mass transfer is controlled by pseudo 2nd order kinetics. Furthermore, the density functional theory simulations demonstrate that the activated carbon strongly interacted with the Cd(II) ion through its various active sites. The adsorption energy noted for all interactive sites is highly negative (-0.45 eV to -10.03 eV), which shows that the adsorption process is spontaneous and stable which is in agreement with the experimental thermodynamics analysis.

The transition to renewable energy sources is pivotal in addressing the escalating challenges of climate change and environmental degradation. Solar energy, particularly photovoltaic (PV) technology, stands out as a prominent solution due to its potential for clean and sustainable electricity generation with minimal greenhouse gas emissions. However, accurately assessing the carbon footprint of PV modules is essential for guiding policy, industry practices, and research. This paper reviews the state of current literature and highlights the difficulties in estimating the carbon footprint of PV modules manufactured in China. It emphasizes the inherent limitations of Process-Based Life Cycle Assessment (PLCA), including data collection challenges, dynamic environmental changes, and subjective methodological choices. The study underscores the need for improved transparency, standardization, and reproducibility in Life Cycle Assessments (LCAs) to provide more accurate and reliable environmental impact evaluations.

This research was to examine the impacts of long-term rice-crayfish coculture systems(RS) on soil nutrients, carbon pools, and rice yields in paddy fields , aiming to establish a scientific basis for the sustainable development of RS in the northern region of Zhejiang. The results showed that the change from rice monoculture (CK) to RS resulted in a 24.99% increase in the 5-year average of soil ammonium nitrogen(AN), while the soil nitrate nitrogen(NN), available potassium(AK), and available phosphorus content(AP) decreased by 28.02%, 16.05%, and 28.76% respectively. Moreover, the total organic carbon(TOC), easily oxidizable organic carbon(EOC), dissolved organic carbon(DOC), and microbial biomass carbon(MBC) decreased by 2.45%, 8.82%, 35.31%, and 65.84% respectively. Correlation analysis showed that there was a significant positive correlation between NN, EOC and MBC in the RS. In terms of rice yield, 5-year average of rice yield in RS has decreased by 8.4% compared to CK.The average yield of planting early-maturing varieties of rice was reduced by 13.16%, while the average yield of planting late-maturing varieties of rice was reduced by 6.00%. In conclusion, enhancing water and nutrient management and cultivating late maturing rice varieties are essential strategies for achieving the sustainable development of RS in northern Zhejiang.

Deforestation through land-use conversion, illegal logging, and timber trafficking is believed to cause ~10% of the annual human carbon dioxide emissions at the global level. Given the large contribution, local and national policies have been set in place in the effort to reduce deforestation and support reforestation. However, accurate assessment of forest carbon stock is expensive and challenging in remote areas and on large geographical scales. To improve carbon stock monitoring and evaluation of fine-scale forest loss, we developed a rapid, automatic, scalable, and cost-efficient generalized deep learning framework that uses diverse remote sensing data and satellite imagery to derive aboveground carbon density from accurate estimates of tree canopy heights at fine-grained resolution (30x30 meters) in remote tropical rainforests. The remote sensing data is composed of Landsat-8, Sentinel-1, land cover, digital elevation model, and NASA CMS airborne LiDAR, as well as vegetation indices, texture metrics, and climatic data. Data sources were compiled into a data pipeline which produced >300 features and 2 million observations over forests in Indonesian Borneo. Using LiDAR swath data on canopy forest high for ~100,000 hectares in Indonesian Borneo to create a training and validation datasets, our neural network model produced aboveground carbon density estimates with R2 of 0.82, which is a significant improvement from comparable works by using Random Forest (R2 of 0.3-0.5). This deep learning framework can be used to facilitate further carbon stock modeling in other forest regions (e.g., Brazil) as well as for the general purpose of climate change mitigation.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

Hypoxia, associated with abnormal vessel growth, is a characteristic feature of many solid tumors that increases their metastatic potential and resistance to radiotherapy. Carbon ion radiation therapy, alone or in combination with other treatments, is one of the most promising treatments for hypoxic tumors because the oxygen enhancement ratio decreases with increasing particle LET. Nevertheless, the current clinical practice does not yet fully benefit from using carbon ions for tackling hypoxia. Here we give an overview of the existing experimental and clinical evidence supporting the efficacy of C-ion radiotherapy in overcoming hypoxia-induced radioresistance, followed by a discussion of the strategies proposed to enhance it, including different approaches to maximize the LET in the tumors.

Despite providing some critical financial services to support the operation of Emissions Trading Systems (ETS), such as increasing market liquidity and price visibility and allowing operators to hedge against future fluctuations, there is growing concern about the potential threat of financial actors' speculation behaviour to the ETS's effectiveness. To confirm or alleviate the fear associated with such concern, we employ both ex-post and ex-ante approaches to determine the role of speculation in the emission reduction effect of the ETS and its forecasting power in predicting climate change. In addition to confirming carbon prices and the speculation behaviour of the emissions non-compliance actors in the ETS as accurate predictors of climate change, we also show that they both matter in the emission reduction effect of the ETS. We use several verifiable econometric approaches to select the Feasible Quasi Generalised Least Squares (FQGLS) as the best estimator for addressing some of the biases in climate change predictability. We demonstrate that a predictive model combining the complementing dynamics of the EST emissions compliance and emissions non-compliance features forecasts climate change more accurately. We demonstrate the robustness of our findings for both in-sample and out-of-sample forecasts and across different forecast horizons by using alternative approaches to evaluate forecast performance.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

With the rapid and continuous advancement and deployment of advanced energy storage de-vices, there has been significant interest in aqueous capacitors that possess non-flammable properties and high safety features. Consequently, extensive research efforts have focused on investigating zinc anodes and low-cost carbonaceous cathode materials. Despite these efforts, the development of high-performance zinc-ion capacitors (ZICs) still faces challenges such as limited cycling stability and low energy densities. In this study, we present a novel approach to address these challenges. We demonstrate the utilization of a three-dimensionally (3D) grown conductive porous carbon framework cathode coupled with zinc anode cells, which exhibit exceptional sta-bility and durability in ZICs. Our experiments reveal a remarkable cycling performance, with a capacity retention of approximately 97.3% and a coulombic efficiency of nearly 100% even after 10,000 charge-discharge cycles. These findings signify significant progress in enhancing the performance of ZICs.

Carbon monoxide (CO) is a cytoprotective endogenous gas that is ubiquitously produced by the stress response enzyme heme-oxygenase. Being a gas, CO rapidly diffuses through tissues and binds to hemoglobin (Hb) increasing carboxyhemoglobin (COHb) levels. COHb can be formed in the erythrocytes or in plasma from cell-free Hb. Herein, it is discussed whether endogenous COHb is or is not an innocuous and inevitable metabolic waste product and it is hypothesized that COHb has a biological role. In the present review literature data is presented to support this hypothesis based on two main premises: (i) there is no direct correlation between COHb levels and CO toxicity; and (ii) COHb seems to have a direct cytoprotective and antioxidant role in erythrocytes and in hemorrhagic models in vivo. Moreover, CO is also antioxidant by generating COHb, which protects against the pro-oxidant damaging effects of cell free Hb. Up to now COHb has been considered as a sink for both exogenous and endogenous CO generated during CO intoxication or heme metabolism, respectively. Hallmarking COHb as an important molecule with a biological (and eventually beneficial) role is a turning point on CO Biology research, namely in CO intoxication and CO cytoprotection.

The build-up of greenhouse gases (GHGs) is causing warmness in the Earth’s atmosphere, resulting in climate change. The transport sector is one of the active members of GHG emissions and it is imperative to use sustainable transport sources to control climate change. The measure aims to encourage citizens to stop using their private vehicles as their choice of transport and instead opt for joint sustainable mobility during traveling. In this study, a quantitative research method was used and data were collected from a sample of 410 respondents through questionnaire. On the other hand, study also took a simulation-based (N=10000) sample size of private vehicle data. The data were analyzed using structural equation modelling. The results revealed that sustainable transportation, climate change technologies and electric rail vehicles reduce climate change in the ecoregions of China. We conclude that sustainable transportation policies could be formulated and implemented to reduce climate change. In response to the research results, it is recommended that, since climate change is a multi-level governance issue and the outdated pyramidal transport industry models must be shifted to a sustainable transportation system model.

Background There is increasing awareness of problems associated with global warming but a lack of a systematic approach on how to deliver more environmentally sustainable dental care. A sustainable world aims to ensure that basic needs and quality of life of everyone are met, now and for future generations. The carbon footprint is an indicator of environmental sustainability. Aim The aim is to suggest an environmental management change for the dental practice focusing on the objective of carbon footprint reduction. Environmental management change design The management change is based on the concept of “Plan-Do-Check-Act”, as recommended by the International Organisation for Standardisation (ISO) and described through the environmental aspects of the dental practice. The approach focuses on establishing and implementing environmental objectives, followed by monitoring results and taking actions to improve continually. The environmental aspects considered for the dental practice are activities causing an impact on the carbon footprint: energy use, travel, product purchasing, waste production, emission to air, water use, and contamination of land. Conclusions The “Plan-Do-Check-Act” ISO 14100-2015 model can be effectively integrated into the dental practice setting for its environmental management. A reduction of the carbon footprint of the dental practice is achieved by applying the environmental management change described for each activity.

The direct growth of single-walled carbon nanotubes (SWCNTs) with a narrow distribution of diameter or chirality remains elusive despite significant benefits in properties and applications. Nanoparticle catalysts are vital for SWCNT synthesis, but how to precisely manipulate their chemistry, size, concentration, and deposition remains difficult, especially within a continuous production process from the gas-phase. Here, we demonstrate the preparation of W₆Co₇ alloyed nanoparticle catalysts with precisely tunable stoichiometry using electrospray, which remain solid state during SWCNT growth. We also demonstrate continuous production of liquid iron nanoparticles with in-line size selection. With the precise size manipulation of catalysts in the range of 1-5 nm, and a nearly monodisperse distribution (σ_g < 1.2), an excellent size selection of SWCNT can be achieved. All of the presented techniques show great potential to facilitate the realization of single-chirality SWCNT production.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.

This article presents the copper ions adsorption process using an activated carbon from winemaking wastes. The pH, temperature, activated carbon amount and initial copper concentration were varied based on a full factorial 2^k experimental design. Kinetic and thermodynamic studies were also carried out. The adsorption kinetics was found follow a pseudo-second-order model. The adsorption data fit better to the Langmuir isotherm. The ANOVA demonstrated that both pH of the solution and activated carbon dosage had the greatest influence on copper adsorption. The activation energy was -32 kJ·mol^-1 suggesting that the copper adsorption is a physic-sorption process. The best fit to a linear correlation was the moving boundary equation that controls the kinetics for the adsorption copper ions onto the activated carbon. The X-ray photoelectron spectroscopy (XPS) results reveal the existence of different copper species (Cu²⁺, Cu⁺ and or Cu⁰) on the surface of the carbonaceous adsorbent after the adsorption, which could suggest a simultaneous reduction process.

The harmful nature of high concentrations of antibiotics to humans and animals requires urgent development of novel materials and techniques for their absorption. In this work, CTAB (Cetyltrimethyl Ammonium Bromide)-assisted synthesis of ZIF-8 (zeolitic imidazolate framework) derived hollow carbon (ZHC) was designed, prepared and used as a high-performance adsorbent, further evaluated by Langmuir and Freundlich isothermal adsorption experiments, dynamic analysis as well as theoretical calculation. The maximum capacities of ZHC on adsorbing tetracycline (TC), norfloxacin (NFO) and levofloxacin (OFO) are 267.3, 125.6 and 227.8 mg g^-1, respectively, which delivers superior adsorptive performance when compared to widely studied inorganic adsorbates. The design concept of ZIFs-derived hollow carbon material provides guidance and insights for the efficient adsorbent of environmental antibiotics.

Pyrolyzed waste biomass, or biochar, has been suggested as a means to increase plant growth and to mitigate soil salinization, which is a widespread agricultural issue and can reach extreme levels in urban soils impacted by de-icing salts. Soil mixing is enhanced by reduced biochar particle size; however, biochar properties vary with particle size and recent studies suggest that plant growth responses may be maximized at intermediate particle sizes. We examined the responses of two plant species (cowpea (Vigna unguiculata) and velvetleaf (Abutilon theophrasti)) to biochar amendments that spanned a wide range of particle sizes obtained by sieving, with and without de-icing salt additions. The smallest size fractions of biochar reduced plant growth relative to unamended controls. Plant biomass production was generally maximized at intermediate biochar particle size treatments, with particles sizes of 0.5-2.0 mm showing the best response. Mitigation of salt effects was also improved at intermediate biochar particle sizes in this particles size range. Our results emphasize the importance of optimizing biochar particle size to best enhance plant responses to biochar, with particular reference to saline soils.

We explore the importance of curvature in carbonaceaous species transformation and stability, using laser-induced vaporisation to evaporate and ionise a source of curved polyaromatic hydrocarbons: carbon nanobelts. Collision impacts between species cause mass loss and the resultant ions are catalogued via mass-spectrometry. To interpret the mass spectra, we perform a series of “in-silico” simulated systematic hydrogen-loss studies using density functional theory (DFT) modelling, sequentially removing hydrogen atoms using thermodynamic stability as a selection for subsequent dehydrogenation. In an initial sequence of H2 removal, the rings are maintained through stable carbyne chain and pentagon-chain formation, giving rise to circular strained dehydrobenzoannulene species. The chains subsequently break, releasing CH and C2. While theoretical closed-cage routes are identified, they are not observed experimentally. The results can serve as a useful guide to high-energy impact conditions observed in some astrochemical environments.

Developing nanomaterials with the capacity to restrict the growth of bacteria and fungus is of current interest. In this study, nanocomposites of poly(2-hydroxyethyl methacrylate) (PHEMA) and carbon nanotubes (CNTs) functionalized with primary amine, hydroxyl, and carboxyl groups were prepared, and characterized. An analysis by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy showed that PHEMA chains were grafted to the functionalized CNTs. The morphology of the prepared nanocomposites studied by field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM) shows significant changes with respect to the observed for pure PHEMA. The thermal behavior of the nanocomposites studied by differential scanning calorimetry (DSC) revels that the functionalized CNTs affects strongly the mobility of the PHEMA chains. Tests carried out by thermogravimetric analysis (TGA) were used to calculate the degree of grafting of the PHEMA chains. The ability of prepared nanocomposites to inhibit the growth of the fungus Candida albicans, and the bacteria Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli was evaluated. A moderated antifungal and antibacterial capacity of the prepared nanocomposites was determined.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

Biomass exploitation is a global trend due to the circular economy and the environmentally friendly spirit. Numerous applications are now based on the use of biomass derived products. Hydrogen sulfide (H2S) is a highly toxic and environmentally hazardous gas, which emitted from various processes. Thus, the efficient removal of this toxic hazardous gas following cost effective processes is an essential requirement. In this study, we present the synthesis and characterization of biomass-derived activated-carbon/zinc-oxide (ZnO@AC) composites from different biomass sources as potential candidates for H2S sorption. The synthesis involved a facile method for activated carbon production via pyrolysis and chemical activation of biomass precursors (spent coffee, Aloe-Vera waste leaves, and corncob). Activated carbon production was followed by the incorporation of zinc oxide nanoparticles into the porous carbon matrix using a simple melt impregnation method. The synthesized ZnO@AC composites were characterized using X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and nitrogen porosimetry. The H2S removal performance of the ZnO@AC composites was evaluated through sorption experiments using a handmade apparatus. Our findings demonstrate that the Aloe-Vera, Spent-coffee, and Corncob derived composites exhibit superior H2S sorption capacity up to 106 mgH2S/gads., 66 mgH2S/gads., and 47 mgH2S/gads. respectively.

The treasury of a DAO is purported to uphold the value of the DAO-issued token, and this study represents a pioneering effort to delve into these realms. We explore the relationship between the treasury and market capitalization in two DAO projects, namely Olympus DAO and KlimaDAO. Employing Granger Causality tests, we scrutinize the relationship between market capitalization and the treasuries of these DAOs. Furthermore, we use an EGARCH model to investigate the in-fluence of carbon offset tokens on KlimaDAO’s market capitalization, incorporating this variable into the model's conditional mean equation. The findings reveal a significant relationship between market capitalization and the treasuries of the DAOs, indicating a potential impact of market capitalization on treasuries. Additionally, the well-specified EGARCH model highlights the sig-nificance of carbon offset tokens, suggesting their potential to influence the overall market capi-talization of a DAO project and support its value.

By sinking and storing carbon from the atmosphere via photosynthesis, forests play a significant role in combating climate change. Global warming is currently the most pressing global issue. Forests play an important role in the global carbon cycle, covering 30% of the world's terrestrial land area and conserving 81% of the earth's terrestrial carbon biomass. The aim of the study was to quantify and map the Carbon Sink and Stock Values of the Yeraba state forest ecosystem. Primary and secondary data sources were used in this study. Primary data such as plot length and width, DBH (diameter at breast height), soil data, and ground control point (GCP) were obtained in the field using a Garmin 72 GPS, a clinometer, and a diameter tape. Diameter tape, caliper and Soil ogre materials. Beside from this sentimental 2 satellite image, there was also another important primary data. In addition to the primary data source, secondary data sources were used. It includes published books, journals and studies, reports, website sources, and other materials that are publicly available. The systematic sampling technique for identifying each intersection point in the area at regular intervals was the most appropriate sampling design for this study. The study used data from four forest carbon pools, including AGB, BGB, soil, and litter, to calculate the carbon sink and stock values of the Yeraba state forest ecosystem. A total of 17 quadrats, each measuring 20m x 20m and spaced 428 m apart, were used to collect vegetation data. For litter and soil sample collection, five 1 m x 1 m sub-quadrats were established at each quadrat's four corners and center. This data was correlated with five Sentinel 2A level 1c imagery data derived vegetation indices of 2023 to obtain a model and estimate of AGB and AGC at the study site. The total mean carbon stock density of Yeraba state Forest was 404.895 t/ha, with 223.656t/ha, 58.15t/ha, 3.41t/ha, and 119.679 t/ha in the above ground carbon, below ground carbon, litter carbon, and soil carbon pools, respectively. The three environmental factors that influence the distribution of different carbon pools in the forest are altitudinal gradient, slope, and aspect. Standing from the result and inputs the researcher recommended that, Future research may find that using LiDAR and Radar imageries, which can address the saturation and canopy penetration issues, will increase the accuracy of carbon stock estimation.

The application of organic fertilizers plays a crucial role in achieving carbon sequestration in the agricultural sector. This paper discusses how farmers can more smoothly promote organic fertilizer extension services. An evolutionary game model is developed to describe the conflicting interests of Chinese farmers and local governments in organic fertilizer extension services, and the dynamic evolution of the game players and the influence of parameter adjustment on the strategic choices of both parties is presented. In this paper, the game model and the main results are validated with the help of simulation tools, and a sensitivity analysis of the selected parameters is performed. The results show that (1) the implementation of subsidy policy is less helpful for organic fertilizer extension services; (2) The ideal event probability of the game was found to be positively related to the cost of applying inorganic fertilizers, additional benefits to farmers, political returns to local governments, and penalties for not using organic fertilizers; (3) This is important for improving the performance of local governments, reducing government regulatory costs, improving policy support for organic fertilizer extension services, and reducing the cost of implementing organic fertilizer extension services.

The production of concrete and the manufacturing process of cement results in a significant carbon footprint, contributing to a large portion of global emissions in structures such as buildings, bridges, roads, and tunnels. Although concrete is an ideal building material that is durable and long-lasting, it can be susceptible to micro-cracks. These micro-cracks in concrete can allow water and chlorine ions to penetrate the structure, leading to the degradation of concrete and corrosion of the reinforcement, posing an unacceptable level of structural risk. Self-healing concrete is not a new material in the construction industry but can be characterized by the capability of concrete to repair its cracks autogenously or autonomously. Recent advancements in concrete research and technology have given us a better understanding of concrete's healing properties. Self-healing concrete combines durability with sustainability while offsetting the high carbon output of concrete manufacturing and production and associated life-cycle costs. Technologies such as microbially-induced calcite (calcium carbonate) precipitation (MICP), shape memory polymers, encapsulation methods, hydration, and swelling agents can potentially reduce carbon emissions while enhancing resilience and longevity. This paper examines these technologies and their applications in the construction industry by comprehensively reviewing the literature and available case studies. The study concluded that there are promising advancements and innovations in concrete, particularly when improving upon the autogenous healing properties. The recommendations for future research include exploring more ways to bring the concrete industry and cement manufacturing toward net zero carbon emissions.

Low-dimensional carbon-based (LDC) materials have attracted extensive research attentions in electrocatalysis because of their unique advantages such as structural diversity, low cost, and chemical tolerance. They have been widely used in a broad range of electrochemical reactions to relief environmental pollution and energy crisis. Typical examples include hydrogen evolution reaction (HER), oxygen evolution reaction (OER), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO₂RR), and nitrogen reduction reaction (NRR). Traditional “trial and error” strategies seriously slowed down the rational design of electrocatalysts for these important applications. Recent studies show that the combination of density functional theory (DFT) calculations and experimental research is capable of accurately predicting the structures of electrocatalysts, thus could reveal the catalytic mechanisms. Herein, current well-recognized collaboration methods of theory and practice are reviewed. The history of modern DFT, commonly used calculation methods, and basic functionals are briefly summarized. Special attention is paid to descriptors that are widely accepted as a bridge links the structure and activity, and the breakthroughs for high-volume accurate prediction of electrocatalysts. Importantly, correlating multiple descriptors are used to systematically describe the complicated interfacial electrocatalytic processes of LDC catalysts. In addition, machine learning and high-throughput simulations are crucial in assisting the discovery of new multiple descriptors and reaction mechanisms. This review will guide the further development of LDC electrocatalysts for extended applications from the aspect of DFT computations.

Assuming that climate warming in the WSL will lead to a northward shift of the forest and permafrost boundaries, a “substituting space for time” approach predicts an increase in concentration of DIC and labile major and trace elements and a decrease of the transport of DOC and low soluble trace metals in the form of colloids in the main stem of the Ob River. However, an unknown factor is the change in hydrochemistry of the largest southern tributary, the Irtysh River, which is impacted by permafrost-free steppe and forest-steppe zone. Overall, seasonally-resolved transect studies of large riverine systems of western Siberia are needed to assess the hydrochemical response of this environmentally-important territory to on-going climate change.

As traditional supply chains face increasingly severe environmental issues and countries promote green development and sustainable development policy concepts, cultivating green supply chain operation models is gradually being highly valued by current governments and enterprises. Generally speaking, the production of green products incurs higher additional costs and thus their total production costs also increase. In this work, the product green level is related to the random demand. Under the green supply chain buy-back contract with the green product R&amp;D cost sharing between the manufacturer and the retailer, both the product green level and the order quantity need to be decided to maximize the channel profit. In order to coordinate the green supply chain, the manufacturer needs to share both the risk of good salvage and the green product R&amp;D cost with the retailer. We find that both the wholesale price and buy-back price increase in the manufacturer’s proposition of the green product R&amp;D cost, but decrease in emission reduction efficiency coefficient or carbon trading price. In addition, the product green level, the optimal order quantity and the channel profit increase in emission reduction efficiency coefficient, but decrease in the R&amp;D cost coefficient of the product green level. Interestingly, we find that if the carbon trading price is low, the manufacturer will set a low product green level and the product carbon emission trading is a cost for the supply chain. The increment of the carbon trading price leads to a higher cost such that the channel profit is decreased. However, if the carbon trading price is high, the manufacturer will set a high product green level and the product carbon emission trading is a revenue for the supply chain. The increment of the carbon trading price leads to a higher revenue such that the channel profit is increased.

In the present study, the polysaccharide-hydrolyzing secretomes of Irpex lacteus BCC104, Pycnoporus coccineus BCC310, and Schizophyllum commune BCC632 were analyzed in submerged fermentation conditions to elucidate the effect of chemically and structurally different carbon sources on the expression of cellulases and xylanase. Among polymeric substrates, crystalline cellulose appeared to be the best carbon source providing the highest endoglucanase, total cellulase, and xylanase activities. Mandarin pomace as a growth substrate for S. commune allowed to achieve comparatively high volumetric activities of all target enzymes while wheat straw induced a significant secretion of cellulase and xylanase activities of I. lacteus and P. coccineus. A synergistic effect on the secretion of cellulases and xylanases by the tested fungi was observed when crystalline cellulose was combined with mandarin pomace. In I. lacteus the cellulase and xylanase production is inducible in the presence of cellulose-rich substrates but is suppressed in the presence of an excess of easily metabolizable carbon source. These enzymes are expressed in a coordinated manner under all conditions studied. It was shown that the substitution of glucose in the inoculum medium with Avicel provides accelerated enzyme production by I. lacteus and higher cellulase and xylanase activities of the fungus. These results add new knowledge to the physiology of basidiomycetes to improve cellulase production.

This study explores the effect of seasonality on soil carbon efflux and pasture growth based on field and lysimeter experiments during summer-fall and winter-spring in two years. Focus is also pointed on irrigation strategies to alleviate the crop response to seasonal fluctuations in precipitation and surface temperatures. Soil respiration, soil and air temperature, leaf photosynthesis, plant dry weight and leaf area index were quantified and analyzed. It has been found significant differences in the CO₂ efflux between the two growing season. Emission of soil CO₂ allowed to characterize and to prioritize the temperature and rain influence in seasonal brachiaria response. During the seasons, the transient variation of CO₂ efflux was highly correlated with rainfall (r = 0.87, P < 0.05), and poorly correlated with soil temperatures (r = 0.5, P < 0.05). The CO₂ efflux and plant response to different level of reposition of evapotranspiration demonstrated that irrigation during fall mitigates the reduction of growth conditioned by drying soil and the lower temperatures. The lower temperatures are limiting only when the soil moisture is below 32% of the field capacity. Thus, we propose to keep the soil moisture around 50% during the fall as a key practices for mitigating the effect of seasonality and its intensification with the climate change, even more if added to management routine practices the soil and water conservation.

In this field pot study, effect of drainage method (e.g., intermittent drainage (ID) and continuous flooding (CF)) on greenhouse gas (GHGs: CO2 and CH4) emission was determined from three Korean paddies (BG, MG, and JS series), varying soil properties such as soil texture, labile carbon, and mineral types. Emission of GHGs was evidently influenced by the irrigation, to a different extent, depending on paddy’s redox (Eh) shift upon flooding events. The Eh decline upon flooding was slower in JS pot, where pore-water concentration of ferric and sulfate ions is the highest (~ up to 3-fold) among three paddies. MG pot was 2- to 3-fold percolative than others and the Eh drop during flooding period was the smallest (staying above -50 mV). In ID treatment, CH4 emission (t CO2-eq ha-1 yr-1) was reduced in a wide range by 5.6 for JS pot, 2.08 for BG pot, and 0.29 for MG pot relative to CF, whereas CO2 emissions (t CO2-eq ha-1 yr-1) was increased by 1.25 for JS pot, 1.07 for BG pot, and 0.48 for MG pot due to the enhanced oxidation of labile carbon. Grain yield and aboveground biomass production from ID were no less than those from CF (p &lt; 0.05). Consequently, gain of global warming potential (S GWP) by ID varied as the order of JS (37%) &gt; BG (14%) &gt; MG (~0 %) pots, and negligible effect observed for MG pot is due to the equivalent trade-off between CO2 and CH4. Our findings suggest that the efficacy of ID practice on GHGs emission can be further improved by the consideration of redox response of paddy system.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

Emission trading schemes (ETSs) have become vital tools in striving toward global emission reduction objectives and promoting a sustainable economy. This paper empirically investigates the impact of market conditions on interconnectedness within precious metals, clean energy, green bonds, and carbon markets, focusing on China and the EU ETSs as the study subjects. A TVP-VAR-based asymmetric connectedness approach is adopted to capture the evolving relationships between the variables of interest in the time–frequency domain. The empirical findings reveal that: First, time-varying asymmetric connectedness and spillover effects among clean energy, precious metals, green bonds, and carbon markets are identified in both time and frequency domains under diverse market conditions, with long-term connectedness asymmetry being particularly sensitive, although spillovers exhibit variations. Second, the role and intensity of net transmitters or receivers vary across market conditions and frequency domains, indicating the complex and nuanced nature of market interactions. The EU ETS demonstrates a higher level of connectivity with global markets for clean energy, precious metals, and green bonds when compared to the Chinese ETS. However, it also shows greater susceptibility to fluctuations in market conditions. These results have significant implications for both investors striving to build sustainable diversified portfolios and regulators endeavoring to craft effective policies for risk regulation and sustainable development.

The Limpopo estuary mangrove forest covers about 928 ha, however 382 ha remain intact and 546 ha were degraded after the 2000 floods. Mangrove replanting campaigns have been carried out at the site. This article aims to evaluate the structure and carbon pool of aboveground and belowground living biomass and soil carbon in natural and replanted mangrove forests (2016, 2014 and 2010). The methodology consisted of selecting 40 strata where structural data were collected. Living biomass above and below ground and soil carbon was obtained based on the methodology described by Kauffman and Donato (2012). The results showed that A. marina was the most observed species in all study areas. The carbon reserve of living biomass above and below ground in the natural forest was 67.9±100.9 MgCha -1 and 65.0±77.1MgC ha -1 , respectively; and in the planted forests (2016, 2014, 2010) it was 1.1±0.5MgCha-1 and 2.1±1.0MgCha-1, 1.8±1.0MgCha-1 and 3.6±2.0MgCha-1, 3.7±2.0MgCha-1 and 5.3±2.5MgCha-1 . Soil carbon reserve was 229.4±119.4 MgCha-1 in natural forest and 230.3±134.8 MgCha-1 , 234.8±132.7MgC ha-1, 229.4±119.4 MgCha-1 in planted forests (2016, 2014, 2010). The total carbon reserve in the natural forest was 362.3 MgCha-1 and in the planted forestsn(2016, 2014, 2010) it was 233.5 MgCha-1 , 240.2 MgCha-1, 246.4 MgCha-1. Natural and restored forests had similar anoumts of soil carbon, which reinforces the idea that soil is a stabel carbon pool. Morever, restored forests failed to store the same amount of live biomass (an carbon), which supports the idea that it is better to prevent habitat degradation than to restore it.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

The benthic matrix acts as a key natural archive where the memory of long-term timescale environmental changes is recorded. Some ecological and chemical features of fjord sediments were explored during the AREX cruise carried out in the Svalbard archipelago in summer 2021. The activity rates of the enzymes leucine aminopeptidase (LAP), beta-glucosidase (GLU) and alkaline phosphatase (AP) and community-level physiological profiles (CLPP) were studied with the aim of determining the functional diversity of the benthic microbial community, while bacterial isolates were screened for their susceptibility to antibiotic molecules in order to explore the role of these extreme environments as potential reservoirs of antibiotic resistance. Enzyme activity rates were obtained by fluorogenic substrates, CLPP by Biolog Ecoplates; antibiotic susceptibility assays were performed through the standard disk diffusion method. Spatial trends observed in the functional profiles of the microbial community suggested the variability in the microbial community composition, presumably related to the patchy distribution of organic substrates. Complex Carbon sources, carbohydrates and amino acids were the organic polymers preferentially metabolized by the microbial community. Multiple resistance to ampicillin, clindamycin and gentamycin was detected in all the sampled sediments, excepting in the southern Hornsund area, stressing the role of sediments as a potential reservoir of chemical wastes ascribable to antibiotic residuals. This study provides new insights on the health status of fjord sediments of West Spitsbergen applying a dual ecological and biochemical approach. Microbial communities in the fjord sediments showed globally a good functional diversity, suggesting their versatility to rapidly react to changing conditions.

This paper examines the interplay between media and the “social side of soils” whereby climate change action implicates individual and collective capacity to adapt, participate in groups or organizations, networks, and respond to challenges and opportunities across a system. The context examined here is Canadian agriculture, and soil health initiatives in the province of Ontario. Our review of relevant literature points to a knowledge gap on the role of the media in enabling climate action in the Canadian agricultural sector with a focus on soil management practices. This study conducted a media content analysis of 100 English-language news articles published between 2022 and 2024 and conducted 31 surveys with media professionals. Approximately one-quarter of the screened news articles contained any relevant coverage of soil health-related climate change mitigation issues. Journalist surveys identified the resource constraints on soil health media coverage with a wide range of traditional and Internet-based journalism on climate change issues, motivated particularly by crisis communication and one-off “parachute reporting”. Going forward, the engagement of key stakeholders of soil health in Canada such as farmers for media and communication about climate change mitigation needs attention. Key policy structures at the federal and provincial levels can help to make this happen.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

The dynamic interaction between carbon nanodots (CNDs) and cannabidiol (CBD) has captured significant attention as an innovative avenue for redefining drug delivery and amplifying therapeutic effectiveness. This in-depth review delves into the intricate synergy between these two elements, unveiling their profound potential in medicine. Commencing with an examination of the unique characteristics of CNDs and the techniques governing their synthesis, we discuss their versatility as drug carriers, highlighting their invaluable role in advancing CBD delivery. Cannabidiol, a non-psychoactive compound sourced from cannabis, has emerged as a focal point for its diverse therapeutic attributes. Nevertheless, the limitations posed by its restricted bioavailability and susceptibility to degradation pose substantial hindrances to realizing its full potential. Here, we elucidate how the amalgamation of CBD with CNDs transcends these challenges. We delve into the mechanisms that underlie this synergy, such as the augmentation of solubility and the safeguarding of CBD against premature breakdown, providing an intricate analysis. We will also journey you through a comprehensive exploration of diverse CBD loading techniques onto CNDs, dissecting the realms of physical encapsulation, covalent bonding, and adsorption processes. In summation, the combination of CNDs and CBD presents an extraordinary opportunity to elevate therapeutic outcomes. This synergetic paradigm masterfully tackles pivotal challenges in drug delivery, thereby paving the path for pioneering medical solutions.

The transition towards a CO2 neutral industry is currently spurring many new developments regarding processes for the conversion of CO2, or CO2-rich streams, into platform molecules such as methanol and dimethyl ether (DME). New processes give rise to new separation challenges, as well as novel opportunities for joint optimization of reaction and separation. In this context, the separation of CO2 and DME can be performed very efficiently using the newly developed concept of Stripping Enhanced Distillation (SED). SED is a distillation process that utilizes an additional stripping component (clearing gas) to promote the separation in the column. SED benefits from the utilization of the feedstock components as a clearing gas that can afterwards be recycled back to the conversion unit with the vapor distillate. Strongly improving the separation performance in the column, this approach also removes the need for external stripping mediums and in addition this recycle approach may significantly reduce the demand on the conversion unit upstream of SED. The benefits of using SED are demonstrated for two different processes for DME synthesis: (i) CO2 – DME separation after the Sorption Enhanced DME Synthesis (SEDMES) process, using hydrogen as clearing gas, and (ii) CO2 – DME separation after direct DME synthesis via dry reforming (DIDR), using methane as clearing gas. For the different cases, it is shown that, with minimal adaptations, the energy consumption for distillation is reduced by 20-30%, while product losses are minimized at the same time.

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

Global change is affecting vegetation cover and processes through multiple pathways. Long time series of surface land surface properties derived from satellite remote sensing offer a unique abilities to observe these changes, particularly in areas with complex topography and limited research infrastructure. Here, we focus on Nepal, a biodiversity hotspot where vegetation productivity is limited by moisture availability (dominated by a summer monsoon) at lower elevations and by temperature at high elevations. We analyze normalized difference vegetation index (NDVI) from 1981 to 2015 semimonthly, at 8 km spatial resolution. We use a random forest (RF) of regression trees to generate a statistical model of NDVI as a function of elevation, land use, CO2 level, temperature, and precipitation. We find that NDVI has increased over the studied period, particularly at low and middle elevations and during fall (post-monsoon). We infer from the fitted RF model that the NDVI linear trend is primarily due to CO2 level (or another environmental parameter that is changing quasi-linearly), and not primarily to temperature or precipitation trends. On the other hand, interannual fluctuation in NDVI is more correlated with temperature and precipitation. RF accurately fits the available data and shows promise for estimating trends and testing hypotheses about their causes.

Greenhouse gases (GHGs) trap heat in the atmosphere, causing the Earth's surface temperature to rise. The main GHGs are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), perfluorocarbons (PFCs), hydrofluorocarbons (HFCs), and sulfur hexafluoride (SF6). Human activities are increasing GHG concentrations rapidly, which is causing global climate change. Global climate change is increasing environmental and public health problems. To reduce greenhouse gas (GHG) emissions, identify where the emissions are coming from, develop a plan to reduce them, and then implement and monitor the plan to ensure that emissions are actually reduced. Anthropogenic global climate change has large and increasingly adverse economic effects. Cities emit the most GHGs due to fossil fuel burning and power usage. The four major GHG emitters are energy, transportation, waste management, and urban land use sectors. Organizations should prepare action plans to lower their GHG emissions and stop the worst consequences of climate change. These action plans require companies and local authorities to submit their GHG emissions reports on a yearly basis. A GHG emissions management system includes several processes and tools created by organizations to understand, measure, monitor, report, and validate their GHG emissions. Two of the most widely adapted frameworks for GHG inventory reporting are ISO 14064 and the GHG Protocol. This review paper aims to identify some of the key points of GHG inventory preparation and mitigation strategies.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

The influence of long-term chemical fertilization in paddy soils is based on the interaction between labile carbon and phosphorus fractions and how this influences soil organic carbon (SOC). Four soil depths (0–30 cm) were analyzed in this study. Easily oxidized organic carbon components, such as permanganate oxidized carbon (POXC) and dissolved organic carbon (DOC), and other physicochemical soil factors were evaluated. The correlation and principal component analyses were used to examine the relationship between soil depth and the parameter dataset. The results showed that Fe-P concentrations were greater in the 0–5 cm soil layer. DOC, inorganic phosphate fraction, and other soil physiochemical characteristics interacted more strongly with SOC in the 0–5 cm soil layer, compared to that in the 10–15 cm layer, influencing soil acidity. An increase in DOC in the 0–5 cm soil layer had a considerable effect on lowering SOC, consistent with P positively correlated with POXC, but negatively with SOC and water-soluble carbon (WSC). The changes in SOC could be attributed to the relationship between DOC and inorganic phosphate fractions (as Fe-P) under a specific soil pH condition. An increase in soil DOC could be caused by changes in the P fraction and pH. The DOC:Avai. P ratio could serve as a compromise for the C and P dynamic indicators. The soil depth interval is a critical element that influences these interactions. Agricultural policy and decision-making may be influenced by the P from chemical fertilization practices, considering the yields and environmental effects.

Windthrows in the forestry fund, which have become more frequent due to the increase in extreme weather events, have had and continue to have negative economic and ecological effects, making them a pressing issue in forestry research. Their urgency has been amplified in light of the need to develop sustainable forest management systems. The main objectives of this study are to evaluate the effects of windthrows on some microbiological properties of forest soils and to monitor the evolution of the degraded tree regeneration, 4 years after the event, for three tree species: Norway spruce (Picea abies L.), sessile oak (Quercus petraea), and European beech (Fagus sylvatica L.). The experimental plot used is arranged in dispersed blocks and subdivided plots, with three repetitions, bifactorial, factor A representing the tree species, and factor B the windthrows: in two situations: affected (AW) and not affected by felling (WW). Three representative soil profiles were studied for each tree species, including dehydrogenase activity (DA) and the number of fungi (NF) in the organic horizon at the soil surface. Dehydrogenase activity was determined by the extraction of triphenylformazan, and NF was evaluated using the Plate Count Method (Petri plates) and the Sabouraud Agar culture medium. The values of Current Dehydrogenase Activity (CDA) and Potential Dehydrogenase Activity (PDA) did not show significant statistical differences in relation to the windthrow factor, but were distinctly significant (p &lt; 0.01) for the tree species factor. On the other hand, NF showed statistical significance for both tree species and windthrows factors, at a level of p &lt; 0.01. Correlations were highlighted between the differences in AW and WW of CDA, PDA, and NF with the number of naturally regenerated seedlings (NRS), and the type of soil. The regressions established between NRS and the differences in CDA and PDA, the dependence of the differences in PDA on the differences in NF, and the regression between the differences in NF and the type of soil demonstrate the importance of soil characteristics in the natural regeneration process of the main tree species - Norway spruce, sessile oak, and European beech. Stimulating NRS in AW forests and increasing the volume of terrestrial organic carbon (TOC) biomass is directly dependent on soil fertility, primarily determined by soil organic carbon (SOC), which accumulates in the soil as a result of organic matter, deposited on the surface. Sustainable forest management of AW plots should stimulate the accumulation of SOC, including the partial or total preservation of dead trees, provided that the attack of specific diseases and pests is avoided.

We studied the dynamics of stable carbon (δ13C) and nitrogen (δ15N) isotopes in litters from Norway spruce (NSL) (Picea abies) and Scots pine (SPL) (Pinus silvestris) during in situ decomposition over a period of more than 4 years. Relative to initial values, δ13CNSL showed a weak enrichment (0.33‰), whereas δ13CSPL resulted in depletion (-0.74‰) at the end of decomposition. Both litter types experienced a depletion in δ15N during decomposition; δ15NNSL decreased by -1.74‰ and δ15NSPL decreased by -1.99‰. The effect of the selective preservation of or acid unhydrolyzable residue (AUR) in lowering δ13C of the residual litter was evident only in SPL. In the NSL, only in the initial stage C/N had a large effect on the δ13C values. In the later stages, there was a non-linear decrease in δ13CNSL with a simultaneous increase in AUR concentrations , but the effect size was large, suggesting the role of lignin in driving δ13C of residues in later stages. Depletion in 15N of the residual litters concomitant with the increase in N concentration suggests bacterial transformation of the litter over fungal components. A consistent decline in δ15N values further implies that bacterial dominance prompted this by immobilizing nitrate depleted in 15N in the residual litter.

This study aimed at characterizing the composition and performing chemical speciation modelling to determine species that are abundant in the coal fly ash (CFA) and soil samples sourced from Hendrina Power station located in Mpumalanga Province. All CFA samples were alkaline in nature with pH values ranging between 8.11 ± 0.07 and 8.60 ± 0.03 with an electrical conductivity (EC) ranging between 301.70 and 1515.00 µS/cm while EC of control soil was 103.10 µS/cm. The control soil pH was found to be 6.24 ± 0.13 and total organic carbon values ranged between 2.68 and 85.82 mg/kg and some percentage organic carbon values of CFAs were found to be greater than 8%, which is above the permissible limits of hazardous waste dumping. Oxidation-reduction potential values were negative in all CFA samples and positive in soil. The speciation modelling showed that the potential for a trace metal to have hazardous effects in soil systems depends on its concentration, specific form and interactions with other constituents in CFA. The slow release of metals from CFA to soil was assessed by looking at how a given metal is distributed throughout its several possible chemical forms. The presence of divalent cations (Pb2+, Cu2+, Zn2+, etc.) in CFAs might pose a threat to soil quality. In the competition for binding sites on ferric hydroxides, dissolved metal ions faced off against other metals. Protons (H+) were seen to be in competition with Pb, Cu and Zn for the ability to bind to hydroxyl (OH-) groups and this is due to chemical precipitation and surface complexation.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

Starting from the environmental issues related to global warming, climate change and reduction of greenhouse gas emissions, this review paper describes how CO₂ recycling can represent a challenging strategy suitable to explore new concepts and opportunities for catalytic and industrial development. In this view, the production of dimethyl ether (DME) from catalytic hydrogenation of CO₂ appears as a viable technology, able to meet also the ever-increasing need for alternative environmentally-friendly fuels and energy carriers. Basic considerations on thermodynamic aspects controlling DME production from CO₂ are presented, then summarizing the main catalytic systems developed in such a field. Special attention is paid on the role assumed during last years by zeolite-based systems, either in the methanol-to-DME dehydration step or in the one-pot CO₂-to-DME hydrogenation. On the whole, the productivity of DME results significantly to be dependent on several catalyst features, linked not only to the metal-oxide phase responsible for CO₂ activation/hydrogenation, but also to specific properties of the zeolites (i.e., topology, porosity, surface area, acidity, interaction with active metals, distributions of metal particles, …) influencing activity and stability of hybridized bifunctional heterogeneous catalysts.

In this study, a three-dimensional bioelectrochemical reactor system (3D-BERs) with granular activated carbon (GAC) epitomizes a novel treatment technology for treating nitrate-polluted water. The conventional denitrification process faces many challenges, including the huge demand for organic carbon, long-term accumulation of intermediate products, and the adaptation period. Results shown that under the optimal conditions of the COD/NO3--N ratio was 1.5, the denitrification efficiency reached 98.62%, when compared to 81.12% at COD/ NO3--N ratio of 3.5, and the initial pH of 7.5 ± 0.5, NO3--N was entirely removed at 2.2 h without accumulation of nitrite. The high initial ratio of NO2--N/NO3--N is mainly to accelerate the denitrification rate by accelerating the reduction of nitrite. Denitrification process followed by zero-order kinetics linear model for at different concentrations of inlet NO3--N, and achieved higher denitrification rate at greater inlet NO3--N concentration. High-throughput sequencing shows that the community structure and relative abundance of bacteria changed significantly, especially at the genes and the phyla level in immobilized GAC particles. Microbial composition enhanced the removal of nitrogen at the inner surface (IS) and bottom surface (BS) of immobilized GAC carriers. Therefore, this system is expected to be a more efficient and useful supplement or a cost-effective alternative compared to the traditional low carbon to nitrogen wastewater treatment system.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

Capturing atmospheric CO2 and storing it in natural rock systems (i.e., alkaline earth silicate and hydroxide minerals) through carbonation reactions is a promising greenhouse gas mitigation research, and largely depends on the use of hydrated ultramafic rocks (serpentinites), which are widespread in orogenic belts around the globe. The Jurassic ophiolites in the Southern Apennines represent a natural analogue and a great opportunity for the mineralogical sequestration of CO2. Serpentinites of the Pollino ophiolite Massif have been widely studied for their mineralogical, petrographic, and chemical characteristics, providing major findings on their impact on environmental and human health issues. Serpentinites here have been divided into cataclastic and massive types based on their structures and are characterized by pseudomorphic and vein textures. The mineralogy of the studied serpentinites consists of lizardite, antigorite, clino-crysotile, Cr-chlorite, magnetite, tremolite, actinolite, pyroxene and calcite, and the most commonly occurring serpentine minerals are polymorphs of serpentine including lizardite, clino-crysotile and antigorite. Systematic petrographic and mineralogical studies of serpentinites in ophiolites, such as those outcropping in the Southern Apennines can represent a starting point for the study of natural materials, which can be used for CO2 storage and sequestration. A particular attention must be given to those carbonate phases, produced by carbonation processes to check whether the serpentinites of the Pollino Massif can be used for the induced mineral Carbon Capture Storage (CCS). If successful, this technique and the Pollino Massif serpentinites can become highly significant in safeguarding the health of our planet's climate.

There is currently much interest in avoiding precious metals in Catalysis. The devel-opment of nickel catalysts to replace palladium in the Mizoroki-Heck reaction is a relevant case in this line of research since both elements share many chemical features. This contri-bution focuses on -Phenyl elimination in alkylnickel complexes. This is the microscopic reverse of olefin insertion (or carbometallation), a fundamental step of the Heck cycle that is usually considered irreversible and selectivity-determining. However, the potential reversibil-ity of carbometallation is generally concealed by the facile beta-hydrogen elimination that follows. Where -hydrogen elimination is hindered, beta-aryl elimination may ensue. We have previously shown that cationic 2-methyl-2-phenylpropyl (neophyl) palladium com-plexes supported by bidentate ligands experience -Ph elimination, which can be seen as an example of olefin de-insertion. In this contribution, we report that -phenyl elimination can also occur in their nickel analogs, in which case fast hydrolyses of the resulting phenyl product can follow the reaction. We investigated the mechanism of these processes and compared their feasibility for nickel and palladium catalysts using DFT calculations. These results are relevant information for the design of nickel-based catalysts for the Heck reac-tion.

Plant and animal agriculture is a part of a larger system where the environment, soil, water, nutrient management interact. Biochar (a pyrolyzed biomass) has been shown to affect the single components of this complex system positively. Biochar is a soil amendment, which has been documented for its benefits as soil enhancer particularly to increase soil carbon, improve soil fertility, and better nutrient retention. These effects have been documented in the literature. Still, there is a need for a broader examination of these single components and effects that aims at the complementarity and synergy attainable with biochar and the animal and crop production system. Thus, we report a comprehensive dataset documenting the interactions of biochar with manure, soil, and plants. We evaluated three biochars mixed with manure alongside both manure and soil controls for improvement in soil quality, reduction in nutrient movement, and increase in plant nutrient availability. We explain the experiments and the dataset which contains the physicochemical properties of each biochar-manure mixture, the physicochemical properties of soil amended with each biochar-manure mixture, and the biomass and nutrient information of plants grown in biochar-manure mixture amended soil. This dataset is useful for continued research examining both the short and long-term effects of biochar-manure mixtures on both plant and soil systems. In addition, these data will be beneficial to extent the findings to field settings for practical and realized gains.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

This paper aims to investigate carbon monoxide (CO) concentrations on roadways of Karachi, potential blood levels carboxy-hemoglobin (COHb) in Karachi. Geographical information system (GIS) was used for spatial analysis of diseases potentiality while an interpolation technique has been applied for surface generation with town boundaries and later evaluates risk areas.The higher concentration of carbon monoxide in the ambient is mainly due to automobile emissions. The City center and CBD areas are more perilous.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

The Glasgow Declaration called for scientifically based measurements of CO2 emissions in the tourism industry to achieve the goals of the Paris Agreement. Despite the economic and employment downturn caused by COVID-19, there are limited cases of environmental assessments related to tourism. This study estimates the carbon footprint of the tourism industry in major G20 countries before and after COVID-19. Understanding the characteristics of inbound tourism and domestic tourism is important as they impact different markets. GHG emissions from tourism mainly stem from transportation, but the type of travel and country differences also make souvenirs, accommodation, and food and beverages significant emission factors. The pandemic has greatly impacted the tourism industry. In 2020, GHG emissions from both domestic and inbound tourism significantly decreased, affecting the number of tourists. In some countries, measures against COVID-19 influenced these figures, and although signs of recovery were observed in 2021, the reduction rates varied by country. These emission reductions should be the goals pursued by the tourism industry in the post-COVID-19 era, requiring efforts to achieve sustainable tourism.