Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

Keywords: underground engineering; numerical simulation; excavation length effect, major principal stress; displacement; damage initiation; CPU time

Pd-Pt catalysts supported on carbon preheated to 1600°C have been reinvestigated in CHFCl2 hydrodechlorination. An additionally adopted catalyst oxidation at 350-400°C produced an order of magnitude increase in the catalytic activity of Pd/C. This increase is not caused by changes in metal dispersion or possible decontamination of the Pd surface from superficial carbon, but rather by unlocking the active surface, originally inaccessible in metal particles tightly packed in the pores of carbon. Burning carbon from the pore walls attached to the metal changes the pore structure, providing easier access for the reactants to the entire palladium surface. As upon calcination the performance of the rest of the Pd-Pt/C catalysts changes less than for Pd/C, the relation between the turnover frequency and alloy composition does not confirm the Pd-Pt synergy invoked in our previous work. The use of even higher-preheated carbon (1800°C), completely free of micropores, results in a Pd/C catalyst that does not need to be oxidized to achieve high activity and excellent selectivity up to CH2F2 (>90%).

Neonatal palliative care (NPC) is an integrated and holistic approach that is an integral part of the contemporary neonatal treatment delivery paradigm. It is the highest fulfillment of the notion of beneficence (doing or creating 'good') that has otherwise been neglected/underestimated by the focus of modern medicine on technology and instrumental treatments by its commitment to alleviating patient pain and quality of life. For decades, the Double-Effect Doctrine (DDE) has been used to consider and address a range of ethically questionable circumstances, often at the end of life, including euthanasia, termination of pregnancy to save maternal life, and morally justified warfare. The theory has continued to be mired in controversy as ethicists, legal scholars, theologians, and philosophers discuss the abstract concepts of moral reasoning, purpose, foresight, and other underlying moral theories. In this paper, the moral theory of DDE is discussed in its clinical application to the ethical decision-making process in neonatal palliative and end-of-life treatment, specifically 1) the administration of opioids as required for symptom control and 2) the use of palliative sedation for intractable symptom care.

Soil CO2 efflux (FCO2) plays a dominant role in the terrestrial carbon (C) cycle but interpreting constraints on local observations is impeded by challenges in disentangling belowground CO2 sources. Trees contribute most C to forest soils, so linking aboveground properties to FCO2 could open new avenues to study plant-soil feedbacks and facilitate scaling; furthermore, FCO2 responds dynamically to meteorological conditions, complicating predictions of total FCO2 and forest C balance. We tested for proximity effects of individual Acer saccharum Marsh. trees on FCO2, comparing FCO2 within 1 m of mature stems to background fluxes before and after an intense rainfall event. Wetting significantly increased background FCO2 (6.4±0.3 vs. 8.6±0.6 s.e. μmol CO2 m-2s-1), with a much larger enhancement near tree stems (6.3±0.3 vs. 10.8±0.4 μmol CO2 m-2s-1). FCO2 varied significantly among individual trees and post-rain values increased with tree diameter (with a slope of 0.058 μmol CO2 m-2s-1 cm-1). Post-wetting amplification of FCO2 (the ‘Birch effect’) in root zones often results from the improved mobility of labile carbohydrates and further metabolization of recalcitrant organic matter, which may both occur at higher densities near larger trees. Our results indicate that plant-soil feedbacks change through tree ontogeny and provide evidence for a novel link between whole-system carbon fluxes and forest structure.

The extracts from the aerial parts of Helianthus salicifolius A. Dietr and Helianthus tuberosus L. collected in June were obtained using carbon dioxide supercritical fluid extraction with water as co-solvent. The antimicrobial activity in vitro of these extracts were determined against the reference species of Gram-positive and Gram-negative bacteria as well as fungi, representing by the yeast species of Candida spp. The following parameters were estimated: minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC). Both extracts were found to possess antimicrobial activity with MIC = 0.62-5 mg mL-1 for bacteria and MIC = 5-10 mg mL-1 for yeasts, showing bactericidal (MBC/MIC = 2-4) or fungicidal effect (MFC/MIC = 1-2 ). The highest activity was observed against S. aureus ATCC 29213 (MIC = 0.62 mg mL-1 for H. salicifolius extract; MIC = 2.5 mg mL-1 for H. tuberosus extract). Bactericidal effect of both extracts against S. aureus ATCC 29213 was confirmed by time-kill assay. Higher antioxidant activity was found for H. tuberosus extract (EC50 = 0.332 mg mL-1) as compared to that of H. salicifolius (EC50 = 0.609 mg mL-1). The total polyphenol content (TPC) expressed as gallic acid equivalents (GAE) was 13.75 ± 0.50 mg GAE (g of H. salicifolius extract)-1 and 33.06 ± 0.80 mg GAE (g of H. tuberosus extract)-1. There was a correlation between the antioxidant potential of both extracts and TPC but not between antistaphylococcal activity and TPC. The obtained data suggest potential application of these extracts as the natural preparations with the biocidal activity, including those with antistaphylococcal activity. Besides, both extracts may be regarded as potential natural conservants in cosmetics as well as natural preservatives in food.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

Less aligned emphasis has been given to the COVID-19 infodemic coordinating with the COVID-19 outbreak. Global profusion of tangled monikers and hashtags has found their ways in daily communication and contributed to backlash against Chinese. Official naming efforts against infodemic should be meet with a fair share of identification. Based on brief critical reviews on previous multifarious naming practices, we punctuate heuristic introspection in scientific conventions and sociocultural paradigms. Infodemiological analysis promises to articulate that people around the globe are divided in their favor stigmatized monikers in the public and scientific communities because of perceptual bias. There is no positive correlation between the degree of infection in their territories and collective perceptual bias to COVID-19. The official portfolio “COVID-19” and “SARS-CoV-2” has not become de facto standard usages, but full-fledged official names are excepted to duly contribute to the resilience of negative perceptual bias and collective behavioral propensities.

It is shown that the termination of the channeling of the fundamental radiation mode in the waveguide can be observed upon heating of an optical integrated circuit based on proton exchange channel waveguides formed in a lithium niobate single crystal. This process is reversible, but restoration of waveguide performance takes tens of minutes. The effect of the waveguide disappearance is observed upon rapid heating (5 °C/min) from a low temperature (minus 40 °C). This effect can lead to a temporary failure of navigation systems using fiber optic gyroscopes with modulators based on a lithium niobate crystal

Torenia Concolor Lindley var. formosama Yamazaki ethanolic extract (TCEE) is reported to have anti-inflammatory and anti-obesity properties. However, the effects of TCEE and its underlying mechanisms in the activation of endothelial nitric oxide synthase (eNOS) have not yet been investigated. Increasing the endothelium-derived nitric oxide (NO) production has been known to be beneficial against the development of cardiovascular diseases. In this study, we investigated the effect of TCEE on eNOS activation and NO-related endothelial function and inflammation by using in vitro system. In endothelial cells (ECs), TCEE increased NO production in a concentration-dependent a manner without affecting the expression of eNOS. In addition, TCEE increased the phosphorylation of eNOS at serine 635 residue (Ser635) and Ser1179, Akt at Ser473, calmodulin kinase II (CaMKII) at threonine residue 286 (Thr286) and AMP-activated protein kinase (AMPK) at Thr172. Moreover, TCEE-induced NO production, and EC proliferation, migration and tube formation were diminished by pretreatment with LY294002 (an Akt inhibitor), KN62 (a CaMKII inhibitor) and compound C (an AMPK inhibitor). Additionally, TCEE attenuated the tumor necrosis factor-α-induced inflammatory response as evidenced by the expression of adhesion molecules in ECs and monocyte adhesion onto ECs. These inflammatory effects of TCEE were abolished by L-NG-nitroarginine methyl ester (a NOS inhibitor). Collectively, our findings suggest that TCEE confers protection from endothelial dysfunction by activating the Akt/CaMKII/AMPK/eNOS/NO signaling pathway.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

An eigenvalue equation representing symmetric (dual) quantum equation is introduced. The particle is described by two scalar wavefunctions, and two vector wavefunctions. The eigenfunction is found to satisfy the quantum Telegraph equation keeping the form of the particle fixed but decaying its amplitude. An analogy with Maxwellian equations is presented. Massive electromagnetic field will satisfy a quantum Telegraph equation instead of a pure wave equation. This equation resembles the motion of the electromagnetic field in a conducting medium. With a particular setting of the scalar and vector wavefunctions, the dual quantum equations are found to yield the quantized Maxwell's equations. The total energy of the particle is related to the phase velocity ($v_p$) of the wave representing it by $E=p\,|v_p|$, where $p$ is the matter wave momentum. A particular solution which describes the process under which the particle undergoes a creation and annihilation is derived. The force acting on the moving particle is expressed in a dual Lorentz-like form. If the particle moves like a fluid, a dissipative (drag) quantum force will arise.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

The literature on the causation of multiple sclerosis (MS), both genetic and environmental, extends over hundreds of years, with no firm conclusions on the exact role of autoimmunity and lifestyle. The epidemiology of MS was the basis for this review, but with a new, extensive examination of genes pertaining to each disorder, and disease of first, and second, degree relatives of those with MS. The author’s motivation was to discover some relationship between MS, and notable familial conditions, as the heredity of MS is concluded to be 30%, and the disorders had a chronic and/or idiopathic nature. This investigation hoped to further understand the randomness of MS- who acquires it, and what symptoms develop- after the author’s decades of observing several incidences of multiple members developing MS in a single family. Online databases for the human genome were used to link genes to MS, and symptoms, including excessive depression, fatigue and suicide rates, in coordination with linking genes for specific familial conditions including seizures, stroke, mental illness, bowel disorders, and thyroid conditions. Interesting associations were found, notably a cluster of Th2 cytokines, known to cure the animal model of MS, important receptors for neurotransmitters and hormones, a gene specific to Epstein Barr Virus, and potential genes for mitochondrial dysfunction. The results surprised the author, showing polygenic regions of chromosome 2 and 5, especially a cluster at loci 5q31-q33, may be dysregulated. The conclusion agrees with past hypotheses MS results not from a single gene, but from various genes, including those expressed in glial cells. The individual theories to the causation of MS, starting with Charcot may be explained by multiple pathways converging into a single disease outcome. In coordination with a sunlight factor, chromosome 2 appears to mediate the immune system, and inflammation, through ultraviolet radiation producing vitamin D3 in the skin, but additionally through peptides formed in the melanocyte stimulating and concentrating hormone class. The impact of stress in MS could be primary, given the loci of several stress-related and stress-modulated genes on these chromosomes, and calls for more appreciation of, and greater care for, the MS patients’ state of mind.

Brain tumors are frequently classified with high accuracy using convolutional neural networks (CNNs) and better comprehend the spatial connections among pixels in complex pictures. Due to their tiny receptive fields, the majority of deep convolutional neural network (DCNN)-based techniques overfit and are unable to extract global context information from more significant regions. While dilated convolution retains data resolution at the output layer and increases the receptive field without adding computation, stacking several dilated convolutions has the drawback of producing a grid effect. To handle gridding artifacts and extract both coarse and fine features from the images, this research suggests using a dilated parallel deep convolutional neural network (PDCNN) architecture that preserves a wide receptive field. To reduce complexity, initially, input images are resized and then grayscale transformed. Data augmentation has since been used to expand the number of datasets. Dilated PDCNN makes use of the lower computational overhead and contributes to the reduction of gridding artifacts. By contrasting various dilation rates, the global path uses a low dilation rate (2,1,1), while the local path uses a high dilation rate (4,2,1) for decremental even numbers to tackle gridding artifacts and extract both coarse and fine features from the two parallel paths. Using three different types of MRI datasets, the suggested dilated PDCNN with the average ensemble method performs better. The accuracy provided by the Multiclass Kaggle dataset-III, Figshare dataset-II, and Binary tumor identification dataset-I is 98.35%, 98.13%, and 98.67%, respectively. In comparison to state-of-the-art techniques, the suggested structure improves results by extracting both fine and coarse features, making it efficient.

Conjugated polymers (CPs) offer potentials for sustainable semiconductor devices due to their low cost, and inherent molecular self-assembly. Enhanced crystallinity and molecular orientation in thin films of solution-processable CPs have significantly improved organic electronic device per-formance. In this work, three methods namely spin-coating, dip-coating, and unidirectional float-ing-film transfer method (UFTM) were utilized with their parametric optimization for fabricating RR-P3HT films. These films were then utilized for their characterization via optical and micro-structural analysis to elucidate dominant roles of molecular orientation, and crystallinity in con-trolling charge transport in organic field-effect transistors (OFETs). OFETs fabricated by RR-P3HT thin films using spin-coating and dip-coating displayed field-effect mobility (μ) of 8.0 × 10-4 cm2V-1s-1 and 1.3 × 10-3 cm2V-1s-1, respectively. This two-time enhancement in (µ for dip-coated films was attributed to its enhanced crystallinity. Interestingly, UFTM films based OFETs demon-strated μ of 7.0 × 10-2 cm2V-1s-1, >100 times increment as compared to its spin-coated counterpart This superior device performance is attributed to synergistic influence of higher crystallinity and molecular orientation. Since the crystallinity of dip-coated and UFTM-thin films are similar ~50 times improved µ of UFTM thin films suggest a dominant role of molecular orientation as com-pared to crystallinity in controlling the charge transport.

A review of literature, supporting the view on the psychophysical origins of some acceptance effects of cyber-physical systems (CPSs), is presented and discussed in the paper. Psychological effects like the reactance to a robot or the uncanny valley phenomenon suggest that CPSs are perceived as a special type of ‘being’, a phylogenetically emergent category, or a novel ontology in a philosophical sense, culturally developing as a function of the social brain. Justification of this view is provided by the psychophysically-relevant human responses to technologically and socially ambiguous stimuli on the one hand, and the probabilistic independence of the proposed ontology to similar ontologies, subjectively experienced by the human, on the other. The results of the presented in the paper analysis demonstrate the feasibility of the proposed hypothesis of ontological ‘near independence’ of the distribution of the probabilistic psychophysical processes in response to the cyber-physical stimulus as a socially evolving phenomenon.

Transition metal complexes have historically played a pivotal role in creating vibrant pigments utilized across artistic mediums such as ceramics, paintings, and glass mosaics. Despite their extensive historical use, our understanding of the mechanisms governing transition metal complex behavior has predominantly emerged in recent times, leaving numerous aspects of this process ripe for exploration. These complexes exhibit striking color variations under diverse conditions when employed in pigment formulations. This review utilizes a bottom-up scientific approach, spanning from microscopic to macroscopic scales, to unravel the molecular origins of the colors generated by transition metal complexes in pigments and ceramic glazes. Advanced spectroscopy techniques and computational chemistry play pivotal roles in this endeavor, highlighting the significance of understanding and utilizing analytical data effectively, with careful consideration of each technique's specific application. Furthermore, the review investigates the influence of processing conditions on color variations, providing valuable insights for artists and manufacturers aiming to enhance the precision and quality of their creations while mitigating environmental impact.

Active front-end (AFE) rectifiers have been becoming widely employed in power systems to achieve unity power factor and harmonic mitigations. The typical modeling approaches applied for AFE rectifiers in the literature mostly relied on two baselines named the detailed model and the time average model. The former approach deals with the switching element model (SEM) leads to significant harmonics in currents with distorted waveforms. The latter approach uses the average-value model (AVM) to overcome the currents’ harmonics as well as provide fast responses. However, even the AVM baseline has contained problems during the starting stage (lack of control signals) and over the dead-time periods which causes serious issues in the implementation process. This paper presents an improved dynamic AVM for AFE rectifiers by precisely considering the issues mentioned above along with the practical starting procedure and desirable initialization. The studied AFE rectifier is developed using the voltage-oriented control (VOC) technique based on the different modeling methodologies including SEM, Conventional AVM, and the proposed AVM. The performance of all models is analyzed and compared using simulation results with MATLAB/Simulink R2023a Function blocks for all the algorithm parts and SimScape elements for the electrical circuit model. The simulation results illustrate that the performance of the proposed AVM approach can closely resemble the behavior of the SEM baseline with low harmonic distortion.

Musculoskeletal infections (MIs) are among the most difficult-to-treat staphylococcal diseases. The limited availability of effective antibiotics has encouraged the development of innovative strategies such as combinatory therapy to combat MI. The aim of this study was to investigate the in vitro antistaphylococcal activity of anti-inflammatory and the antimicrobial combinatory effect of celecoxib with oxacillin. The minimum inhibitory concentrations (MICs) of 17 anti-inflammatory drugs were determined for standard strains and clinical isolates of S. aureus strains, counting methicillin-resistant strains (MRSA), by the broth microdilution method. The fractional inhibitory concentration indices (FICIs) were evaluated by the checkerboard assays. Celecoxib produced the most potent antistaphylococcal effect against all the tested strains (MIC ranging from 32 to 64 mg/mL), followed by diacerein against MRSA3 and MRSA ATCC 33592 (MIC 64 mg/mL). Several synergistic effects were observed for tested S. aureus strains, including MRSA (FICI ranging from 0.087 to 0.471). The strongest synergistic interaction (FICI 0.087) was obtained against MRSA ATCC 33592 at a celecoxib concentration of 2 mg/mL with a 19-fold oxacillin MIC reduction (from 512 to 26.888 mg/mL). This is the first report on the antistaphylococcal combinatory effect of celecoxib with oxacillin. Our findings suggest celecoxib and its combination with oxacillin as perspective agents for research focused on the development of novel therapies for MI caused by S. aureus. Thus, this study presents novel findings that celecoxib could, in some cases, resensitise MRSA strains to become susceptible to certain β-lactams (e.g., oxacillin) not previously tested.

A novel high-speed directly modulated two-section distributed feedback (TS-DFB) semiconductor laser based on the detuned-loading effect is proposed and simulated. Grating structure is designed by reconstruction-equivalent-chirp (REC) technique. A π phase-shift is introduced into the reflection grating, which can provide a narrow-band reflection region with a sharp falling slope on both sides of the reflection spectrum, thus enhancing the detuned-loading effect. Owing to its unique dual-falling-edges structure the bandwidth can be improved even when the lasing wavelength shifts beyond the left falling edge due to thermal effect in actual test, in which condition the detuned-loading effect can be used twice, which greatly improves the yield. The modulation bandwidth is increased from 17.5 GHz for a single DFB laser to around 24 GHz when the lasing wavelength is located on the left falling edge of the TS-DFB laser based on detuned-loading effect, and can be increased to 22 GHz for the right side. An eight-channel laser array with precise wavelength spacing is investigated, with side mode suppression ratio (SMSR) > 36dB. Besides, TS-DFB lasers with uniform reflection grating are studied and simulated result shows that modulation characteristic is far inferior to the laser with a phase-shifted grating reflector.

The main aim of this study is to predict whether the type of breast cancer is “benign” or “malignant” by classical generalized linear model (GLM) approach and an extended family of GLM called generalized linear mixed model (GLMM) approach for binomially distributed response variable with binary link functions. In this study, an advanced statistical modeling approach based on the GLMM to the traditional statistical modeling approach based on the GLM for binomially distributed response variable with various binary link functions is proposed to investigate the relationships between the “malignant or benign diagnosis of the BC in patients” and “nine attributes” of 699 BC diagnosed patients. This study also focuses on the statistical significance of the accurate classification of the BC diagnosed patients in cancer studies in medicine in “benign” or “malignant” type based on the WBC dataset. In this study, the superiority of the GLMM approach over the GLM approach for the binary response variable especially belonging to the WBC dataset is emphasized in the field of cancer diagnosis in medicine. Also the importance and the power of the IC and performance metrics as the goodness-of-fit test statistics are strongly emphasized for accurate statistical inferences from the “best” fitted model. In this study, from the main findings, the best fitted model among the GLM and GLMM approaches for the binary response variable is determined as the GLMM under “logit” link function with “id” random effect with the most statistically significant odds of the occurance of the BC being “malignant” as 7.9104, 5.6888, 5.6643, 4.9842, 4.1212, 2.0679, 1.8755, and 1.3970 times more than being “benign” for every one-unit increase in the quantities of “clump thickness”, “bland chromatin”, “mitoses”, “bare nuclei”, “cell shape”, “marginal adhesion”, “epithelial cell size”, and “cell size”, respectively.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Cardiovascular diseases (CVDs) represent the leading cause of global mortality with 1,7 million deaths a year. One of the alternative systems to drug therapy to minimize the risk of CVDs is represented by alpha-linolenic acid (ALA), an essential fatty acid of the Omega-3 series, known for its cholesterol-lowering effect. The main purpose of this review is to analyze the effects of ALA and investigate the relevant n-6/n-3 ratio in order to maintain functionally beneficial effects. Concerning the lipid-lowering preventive effects, ALA may favorably affect the values of LDL-C and triglycerides in either adult and pediatric populations and it has a positive and protective effect against hypertension, suggesting that ALA is an useful diet-related antihypertensive compound. According to the 2009 EFSA statement, dietary ALA may contribute to reducing the risk of CVDs, thanks to anti-hypertensive, anti-atherosclerotic and cardio-protective effects.

Computer and Smart Device-assisted Learning (CSDL) has gained increasing attention from educational researchers and practitioners in recent years. However, it remains controversial whether student can benefit from CSDL and what moderator could affect the impact of CSDL. Within the specific context of Korea, where the interest in digital education is steadily increasing, the number of empirical studies exploring the causal effect of CSDL remains relatively scarce. The primary objective of this empirical study was to investigate the impact of CSDL on students' academic achievement in Korea. To achieve this objective, a two-way fixed effect model was employed, utilizing a panel dataset spanning three years derived from the 'Korean Education Longitudinal Study 2013'. The findings revealed a significant positive impact of CSDL on students’ Mathematics achievement. Notably, higher income levels, increased availability of computer resources provided by schools, and the implementation of more individualized education were identified as factors that moderate the effect of CSDL on students' achievement levels in Korean and English subjects. These findings underscore the need for an approach that optimizes the educational benefits of CSDL by considering subject-specific characteristics. Furthermore, this study highlights the importance of allocating educational resources, such as computers and smart devices, and integrating individualized educational activities within the classroom environment.

: Airports are often the centers driving economic development of the local community in which they are located and have a significant impact on the national economy. Therefore, the infrastructural development of the airport is of great importance. On the other hand, passengers are becoming more experienced, more informed and more demanding in achieving their own satisfaction related to the level of quality of the service provided. The new airport infrastructure has an impact on improvement of customer experience, but with the assumption that certain physical and operational conditions are met. The research found that, in addition to the facilities that are part of the passenger operations, passengers pay significant attention to the commercial facilities, design and ambiance of the passenger terminal. It can be concluded that with the new airport infrastructure development such as passenger terminal, a wow effect at the customers will be achieved, but that only right design of ambient, simplified passenger flows and organization of commercial areas with a diverse offer and acceptable prices will ensure long term customer satisfaction and that the experience gap remains positive and sustainable.

Background and Objectives: Mucilaginous substances from plant extracts are known to be able to support the lubricating effect of hyaluronic acid (HA) in dry eye disease (DED). In this pilot study, the combined lubricating effect of HA and mallow extract (Malva sylvestris L.) in patients with DED was assessed. Materials and Methods: 20 patients at 5 ophthalmological practices in Italy were treated with eye drops, containing HA and mallow extract on the one hand, and with eye drops containing HA only, on the other hand, in a two-period crossover design. As primary endpoints, the tear film breakup time (TBUT), the reduction of lissamine green staining of the ocular surface (Oxford Scheme, OS), and the safety and efficacy assessment by the ophthalmologists were evaluated. As secondary variables, the patient symptom score, the ocular surface index (OSDI), and the satisfaction, preference and efficacy judgement by the patients were evaluated. All data were analysed descriptively in addition to an exploratory analysis of the target variables. Results: Both products were well tolerated. There were no statistically significant differences, with regard to the TBUT, OS and OSDI, between both treatments. Anyway, the efficacy and safety assessments by the ophthalmologists and the patients showed results in favour of the combined product. Conclusion: The addition of mallow extract to HA containing eye drops enhances the treatment of DED at least with respect to subjective measurements. Further assessments will have to be done to prove and explain this observation in terms of measurable parameters, e.g. markers for inflammatory cytokines.

To explore the impact of parenting styles on the perception of campus non-physical bullying, 492 students in upper elementary school grades were surveyed by using the Delaware Bullying Victimization Scale, the Negative Coping Style Scale, the Negative Affect Scale, and the Egna Minnen Beträffende Uppfostran Questionnaire. The questionnaire survey was conducted in the fifth and sixth grades of eight primary schools in Zhejiang province. The results showed that cyberbullying was not significantly related to an anxious parenting style, but negative affect experiences, negative coping styles, negative family parenting styles, and the perception of campus non-physical bullying were all positively correlated with each other (p < 0.05). The refusal parenting style was shown to be an important factor that affected students’ perception of campus non-physical bullying; it was observed to directly affect students’ perception of campus non-physical bullying and indirectly affect students’ perception of campus non-physical bullying by influencing negative affect experiences and negative coping styles. In conclusion, negative affect experiences and negative coping styles had a chain-like mediating effect between the refusal parenting style and students’ perception of campus verbal bullying. Moreover, negative affect experiences had a partial mediating effect between the refusal parenting style and students’ perceptions of campus cyberbullying, relationship bullying, and non-physical bullying total scores. Implications and suggestions based on these results are also discussed.

The present study was aimed at revealing the influence of the mechanical stress induced by water molecules adsorption on the composition of crystalline phases in the ZrO2–3mol%Y2O3-nanoparticles. Three basic methods have been used to determine the phase transition: neutron diffraction, Raman microspectroscopic scanning, and X-ray diffraction. The fact of phase-structural β → α transformation and the simultaneous presence of two polymorphic structural modifications (β is the phase of the tetragonal syngony and α of monoclinic syngony in nanosized particles (9nm)) under normal physical conditions was established by these methods. Satisfactory consistency was achieved between the results obtained using different techniques.

Product Design is getting nowadays new challenges on developing new products, since the industry is in a rush to introduce products into the marketplace, where customers demand products faster, cheaper, and free of failures. In the meantime, global companies are always trying to improve their Product Design process to get advantages over their competitors using proven tools like FEMA and mixing methodologies like Fuzzy theories with FMEA. Even today using all this tools and combination of methodologies there is a gap to address and it is required a robust risk analysis solving current issues in the electronic industry. This document aims to reveal a novel integrated method, where Failure Mode and Effect Analysis, Pythagorean Fuzzy Sets and Dimensional Analysis are cohesive into a model that minimize the uncertainty of the ranking and prioritization over the Failure Mode and Effect Analysis execution, helping to identify risks within an accurate grade over possible failures in the Product Design process. A real practical example is used to show the proposed method, where it is identified a robust methodology integration and solid and results using a sensitivity analysis.

The combined effects of global warming and increasing urban heat islands (UHIs) on air temperature and heat stress in cities are notable physical and mental health implications for citizens. With research having shown the effective role of urban green spaces in decreasing urban heat, this study investigated the cooling effect of a large urban park on thermal comfort outside the park area, from psychological and physiological perspectives. The studied park is located in the center of Madrid and adjacent to UHI. The study was performed by conducting field measurements and a survey with questionnaires. The measurements made on six summer days (with two-week intervals) showed that the park’s cooling effect could decrease the air temperature by 2.4-2.8°C right up to the edge of the heat island (600m), and decrease the physiological equivalent temperature (PET) by about 3.9°C. By decreasing air temperature and PET, this park was also shown to increase the perceived thermal comfort (PTC) of the citizens from the psychological perspective in the defined area of effect. This perceived thermal comfort was found to have a significant inverse relationship with PET (P-value <0.05). The examination of cognitive maps drawn by citizens showed that out of the 145 respondents, 68.3% marked the park as the area that they perceive as having the greatest thermal comfort, and prefer as the place to spend time enjoying thermal comfort, irrespective of its distance from their location.

The time-resolved flowfield of a spatially oscillating jet emitted by a Sweeping Jet (SWJ) actuator is investigated numerically using three-dimensional Reynolds-averaged Navier-Stokes (3D-URANS) equations. Numerical simulations are performed for a practical range of mass flow rates providing flow conditions ranging from incompressible to subsonic compressible flows. A linear relationship between the mass flow rate and the jet oscillation frequency is found. The results of the numerical model are compared with the experimental data in the literature, and good agreement is found. Additionally, it is observed that the SWJ actuator frequency response switches from one linear mode to another linear mode when the compressibility effects become important.

The radiosensitivity of biological systems is strongly affected by the system oxygenation. On the nanoscopic scale and molecular level, this effect is considered to be strongly related to the indirect damage of radiation. Even though particle track radiolysis has been the object of several studies, still little is known about the nanoscopic impact of target oxygenation on the radical yields. We present here an extension of the chemical module of the Monte Carlo particle track structure code TRAX, taking into account the presence of dissolved molecular oxygen in the target material. The impact of the target oxygenation level on the chemical track evolution and the yields of all the relevant chemical species is studied in water under different irradiation conditions: different linear energy transfer (LET) values, different oxygenation levels, and different particle types. Especially for low LET radiation, a large production of two highly toxic species (HO₂^• and O₂^•− ), which are not produced in anoxic conditions, is predicted and quantified in oxygenated solutions. The remarkable correlation between the HO₂^• and O₂^•− production yield and the oxygen enhancement ratio observed in biological systems suggests a direct or indirect involvement of HO₂^• and O₂^•− in the oxygen sensitization effect. The results are in agreement with available experimental data and previous computational approaches. An analysis of the oxygen depletion rate in different radiation conditions is also reported.

Defects in pre-mRNA splicing are frequently a cause of Mendelian disease. Despite the advent of next-generation sequencing, allowing a deeper insight into a patient’s variant landscape, the ability to characterize variants causing splicing defects has not progressed with the same speed. To address this, recent years have seen a sharp spike in the number of splice prediction tools leveraging machine learning approaches, leaving clinical geneticists with a plethora of choices for in silico analysis. In this Review, some basic principles of machine learning are introduced in the context of genomics and splicing analysis. A critical comparative approach is then used to describe seven recent machine learning-based splice prediction tools, revealing highly diverse approaches and common caveats. We find that, although great progress has been made in producing specific and sensitive tools, there is still much scope for personalized approaches to prediction of variant impact on splicing. Such approaches may increase diagnostic yields and underpin improvements to patient care.

Inequality of health service for different specialty categories not only occurs in different areas inequality of health service for different specialty categories in the world, but also happens in the online service platform. In the online health community (OHC), health service was often of inequality for different specialty categories, including both online views and medical consultation for offline registered service. Moreover, how the factor city-level impacts the inequality of health service in OHC is still unknown. We designed a causal inference study with data on distributions of serviced patients and online views in over 100 distinct specialty categories on one largest OHC in China. To derive the causal effect of the city-levels (two levels inducing 1 and 0) on the Gini coefficient, we matched the focus cases in cities of rich healthcare resources with the potential control cities. For the Gini coefficient of serviced patients in over 100 specialty categories, the average treatment effect of level-1 cities is 0.470, which is 0.029 higher than that of the matched group. Similarly, for the Gini coefficient of online views, the average treatment effect of Level-1 cities is 0.573, which is 0.016 higher than that of the matched group. For each of the specialty categories, we also estimated the average treatment effect the specialty category’s Gini coefficient ( ) with the balanced covariates. The results support the argument that the total Gini coefficient of all the doctors in OHC shows that the inequality of health service is still very serious. This study contributes to the development of the theoretically grounded understanding of the causal effect of city-level on the inequality of health service in an online to offline healthcare service setting.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

We investigate emergent conductive phenomena triggered by collinear antiferromagnetic orderings. We show that an up-down-zero spin configuration in a triangle cluster leads to linear and nonlinear spin conductivities even without the relativistic spin–orbit coupling; the linear spin conductivity is characterized by the Drude-type one, while the nonlinear spin conductivity is characterized by the Hall-type one. We demonstrate the emergence of both spin conductivities in the breathing kagome system consisting of a triangle cluster. The nonlinear spin conductivity becomes larger than the linear one when the Fermi level lies near the region where a small partial band gap opens. Our results indicate that collinear antiferromagnets with the triangle geometry give rise to rich spin conductive phenomena.

We have investigated the influence of the relative proportions of glass formers in a series of lithium alumino-borosilicate glasses with respect to electrical conductivity () and glass transition temperature (Tg) as functions of glass structure, as determined by Raman spectroscopy. The ternary lithium alumino-borate glass exhibits the highest  and lowest Tg among all the compositions of the glass series, 30Li2O•3Al2O3• (67-x) B2O3•xSiO2. However, as B2O3 is replaced by SiO2, a shallow minimum in  as well as a shallow maximum in Tg are observed near x = 27, where the Raman spectra indicate isolated diborate/tetraborate/orthoborate groups are being progressively replaced by danburite/reedmergnerite-like borosilicate network units. Overall, as the glasses become silica-rich,  is minimized, while Tg is maximized. In general, these findings show correlations among Tg, (sensitive to network polymerization),  (proportional to ionic mobility), and the different borate and silicate glass structural units as determined by Raman spectroscopy. X-ray diffraction analyses demonstrate the absence of appreciable crystallinity in the glasses investigated. However, scanning electron microscopy (SEM) images of HF-etched samples showed that glasses, and especially the borate-rich compositions comprise two distinct glassy phases. The isolated phase is 25-100 nm in diameter, dispersed evenly in a glassy matrix.

In this article, many experimental similarities between electromagnetic fields (which are applied in systems of electrons, atoms, and liquids) and strong interaction fields (which are applied in systems of quarks, nucleons, and nuclei) are reviewed. The currently accepted theories describing electromagnetic fields differ fundamentally from those describing strong fields. Therefore, the many similarities are quite surprising, and some are not adequately explained even today. Several such unexplained similarities are listed among the top open problems in particle physics, such as the “EMC effect,” the “proton spin crisis,” and the “strong CP problem.” This paper highlights, for the first time, the underlying common characteristics of these problems, potentially offering valuable contribution to future explanations.

Perceived peer support is a critical factor in the academic adjustment of higher vocational college students. While previous studies have explored this relationship, few studies have delved into the underlying mechanisms. This study surveyed 9782 students from 35 higher vocational colleges in 13 provinces and cities in China to explore the relationship and mechanisms between perceived peer support and academic adjustment. Drawing on Conservation of Resources theory and Social Support Resource theory, the findings revealed that perceived peer support not only directly predicted the academic adjustment of higher vocational college students, but also indirectly through the independent mediating effect of academic hope and professional identity, as well as the chain-mediating effect of academic hope to professional identity. Additionally, students from vocational high schools showed a more significant increase in academic hope due to perceived peer support compared to those from general high schools, highlighting the moderating effect of educational background. The study provided a new theoretical perspective for understanding the complex mechanisms of academic adjustment in students and offers valuable guidance for educational practice, emphasizing the importance of fostering perceived peer support, academic hope, and professional identity in higher vocational education.

In the process of climate change mitigation and adaptation, the focus on climate risks driven by transition innovations has received widespread attention from governments, regulators and investors. Based on the identification of low-carbon patents through the Green and Low-carbon Technology Inventory in China, we construct low-carbon innovation measurements of listed firms in China from 2015 to 2021 then an empirical model is used to investigate the impact and mechanism of climate transition innovations on the default risk. The baseline regression model shows that low-carbon innovations can mitigate the default risk of firms. Moreover, our findings are supported by instrumental variable regressions that use time costs of innovation. In addition, the mediation effect demonstrates that investor attention, total factor productivity, and technology spillovers are paths for transition innovations to affect the default risk. This study reveals that low-carbon technological advances have a positive effect on climate transition risks. Further, it provides empirical evidence for listed companies to develop low-carbon innovations.

Abstract Background: Cluster randomized controlled trials are increasingly becoming popular in public health research interventions and health services research in primary health care design and use in low and middle-income countries. However, the majority of researchers in these trials did not account correctly for the effect of confounders and clustering in the design and analysis stages. Objectives: This article aimed to review the main implications of implementing a cluster randomized controlled trials design in public health research and emphasize the practical application of proper analytical methods and the performance of different statistical models. Methods: The practical application of various analytical methods is validated via the utilization of experimental data from a public health research case study. This article also demonstrated the performance of hierarchical models and made comparisons in terms of empirically precise effect size estimates. Results: Three hierarchical statistical models were provided with highly varied effect sizes during the analysis of the intervention effect on outcome, such as model 1 (AOR: 14.32; 95% CI: 3.75–54.68), model 2 (ARR: 3.52; 95% CI: 2.16–5.77), and model 3 (ARR: 4.79; 95% CI: 2.69–5.52).Conclusion: Inaccurate results and potentially misleading conclusions can arise from improper cluster randomized controlled trial designs and analyses. This article has shown that real-world data can be adjusted for the effects of confounders and clustering, and we advocate for the routine use of suitable design and analytical methods. This article concludes that researchers should be careful when selecting hierarchical models to analyze cluster randomized controlled trials.

Wounds represents a medical problem that contribute importantly to patient morbidity and to the healthcare costs in several pathologies. In Hidalgo, Mexico, Bacopa procumbens plant has been traditionally used for wound healing care for several generations; in vitro and in vivo experiments were design to evaluate the effects of bioactive compounds obtained from B. procumbens aquoethanolic extract and to determine the key pathways involved in wound regeneration. Bioactive compounds were characterized by HPLC- QTOF-MS and proliferation, migration, adhesion, and differentiation studies were done on NIH/3T3 fibroblasts. Polyphenolic compounds from Bacopa procumbens (PB) regulated proliferation and cell adhesion; enhanced migration reducing the artificial scratch area; and modulated cell differentiation. PB compounds were included in a hydrogel for topical administration on rat excision wound model. Histological, histochemical and mechanical analysis showed that PB treatment accelerates wound closure in at least 48 h; reduce inflammation, increasing cell proliferation and deposition and organization of collagen in earlier times. These changes resulted in the formation of a scar with better tensile properties. Immunohistochemistry and RT-PCR molecular analyses demonstrated that treatment induces: i) overexpression of transforming growth factor beta (TGF-β); and ii) the phosphorylation of Smad 2/3 and ERK1/2, suggesting the central role of some PB to enhance wound healing, modulating TGF-β activation.

Background: Tele-emergency physicians (TEPs) take an increasingly important role in the need-oriented provision of emergency patient care. To improve emergency medicine in rural areas, we set up the project Land|Rettung (English: Rural|Rescue), which uses TEPs to restructure professional rescue services using information and communication technologies (ICTs) in order to reduce the therapy-free interval. Successful implementation of ICTs relies on user acceptance and knowledge sharing behavior. Methods and findings: We conducted a factorial design with active knowledge transfer and technology acceptance as a function of work satisfaction (high vs. low), workload (high vs. low) and point in time (prior to vs. after digitalization). Data were collected via machine readable questionnaires issued to 755 persons (411 pre, 344 post), of which 304 or 40.3% of these persons responded (194 pre, 115 post).Technology acceptance was higher after the implementation of TEP for nurses but not for other professional groups, and it was higher when the workload was high. Regarding active communication and knowledge sharing, employees with low work satisfaction are more likely to share their digital knowledge as compared to employees with high work satisfaction. Additional and more detailed analyses reveal that this is an effect of previous knowledge concerning digitalization. After implementing the new technology, work satisfaction increased for the more experienced employees, but not for the less experienced ones. Results are discussed considering the Dunning-Kruger effect. The Dunning-Kruger effect describes a cognitive bias. People with high expertise often underestimate their actual skill level. They have a more critical attitude towards their performance and feel the urgent need to fill possible knowledge gaps they notice. Conclusions: Our research illustrates that employees’ workload has an impact on the intention of using digital applications. The higher the workload, the more people are willing to use TEPs. Regarding active knowledge sharing, we see that employees with low work satisfaction are more likely to share their digital knowledge compared to employees with high work satisfaction. This might be attributed to the Dunning-Kruger effect. Highly knowledgeable employees initially feel uncertain about the change, which translates into temporarily lower work satisfaction. They feel the urge to fill even small knowledge gaps, which in return leads to higher work satisfaction. Those responsible need to acknowledge that digital change affects their employees’ workflow and work satisfaction. During such times, employees need time and support to gather information and knowledge in order to cope with digitally changed tasks.

This study examines the spatial impact of FDI on the poverty of 44 African countries. In achieving this, the study uses the Driscoll-Kraay fixed effect instrumental variable regression, instrumental variable generalised method of moments estimator (IV-GMM), and the spatial durbin model. The empirical investigation of this study yielded four significant findings: (1) neighbouring countries’ FDI has a positive and significant impact on the incidence and intensity of host country’s poverty. (2) Improved institutional quality in neighbouring countries has a significant impact on FDI-poverty reduction nexus of the host country. (3) the empirical results lend support for a significant spatial spillover of poverty in the region. (4) the marginal effect results indicate that countries within the region are no longer in isolation or independent, i.e., the level of poverty in a particular country is influenced by its determinants in the neighbouring country. This result is robust to the alternative proximity matrix, which is the inverse distance. Since there is spatial interdependence among African countries, we recommend that African governments through the African Union (AU) should not only champion the institutional reform in the region, but also establish a binding mechanism to ensure reform implementation.

Introduction. Bacterial resistance to antibiotics is estimated to cause the major number of deaths by 2050 if we do not find strategies to slow down the rise of drug resistance [1]. Reviews on Mediterranean Wild Edible Plants (MWEPs) with antimicrobial properties are scarce in the mean databases (Pubmed, Scopus and WoS). Hence, we proceeded to a new review of the studies on MWEPs. Methods. We used Wild Edible Plant and Antimicrobial as keywords. We only included the Mediterranean plants, and studies in non-Mediterranean countries, but for plants growing in Mediterranean basin. Exclusion criteria were the document type, studies not concerning plant, plants not edible, not antimicrobial properties, or totally out of topic. Results. Finally, the number of studies reviewed, starting from one hundred and ninety-two, was thirty-eight (19,8%), concerning the antimicrobial properties of seventy-four MWEPs species, be-longing to twenty-five Families. Fifty-seven (77%) out of seventy-four species, proved to be antimicrobial with a stringent threshold selection. Conclusions. The studies are still very heterogeneous. We still know too little about MWEPs properties, but what we already know seriously recommends continuing.

There is a need to search for new antifungals, especially for the treatment of the invasive Candida infections, caused mainly by C. albicans. These infections are steadily increasing at an alarming rate, mostly among immunocompromised patients. The newly synthesized compounds (3a-3k) were characterized by physico-chemical parameters and investigated for antimicrobial activity using the microdilution broth method to estimate minimal inhibitory concentration (MIC). Additionally, their antibiofilm activity and mode of action together with the effect on the membrane permeability in C. albicans were investigated. Biofilm biomass and its metabolic activity were quantitatively measured using crystal violet (CV) staining and tetrazolium salt (XTT) reduction assay. The cytotoxic effect on normal human lung fibroblasts and hemolytic effect were also evaluated. The results showed differential activity of the compounds against yeasts (MIC = 0.24-500 µg/mL) and bacteria (MIC = 125-1000 µg/mL). Most compounds possessed strong antifungal activity (MIC = 0.24-7.81 µg/mL). The compounds 3b, 3c, and 3e, showed no inhibitory (at 1/2 MIC) and eradication (at 8 x MIC) effect on C. albicans biofilm. Only slight decrease in the biofilm metabolic activity was observed for compound 3b. Moreover, the studied compounds increased the permeability of the membrane/cell wall of C. albicans and their mode of action may be related to action within the fungal cell wall structure and/or within the cell membrane. It is worth noting that the compounds had no cytotoxicity effect on pulmonary fibroblasts and erythrocytes at concentrations showing anticandidal activity. The present studies in vitro confirm that these derivatives appear to be a very promising group of antifungals for further preclinical studies.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

This research paper examines the effects, advantages, challenges, and economic aspects of a research town. The study concludes that inclusion and diversity not only constitute fundamental values but also serve as crucial drivers of business success and sustained competitiveness. Universities play a central role in shaping the prosperity of the research town by functioning as knowledge hubs, fostering collaboration, nurturing talent, and contributing to the broader innovation ecosystem. The symbiotic relationship between universities and industries within the cluster establishes a dynamic and resilient environment for research and development. The presence of startups within the research cluster introduces novel ideas, enhancing the overall vibrancy and competitiveness of the local economy. In an era where social media algorithms increasingly influence people's choices, the potential for foreign interference emerges as a significant threat.

In cosmology dark energy and dark matter are included in the ΛCDM model, but they are still completely unknown. Because in black holes Lorentz invariance seems not to be applicable for curved space-time, we introduce a model for a reduced speed of light in black holes due to quantum gravity effects and the Heisenberg uncertainty relation. Then black holes are a source for a scalar field with dark energy characteristics. This model has no information paradox for black holes because particles / radiation entering the black hole are redshifted in their wavelength that far that the wavelength has the size of the Schwarzschild radius and thus they are in some way "frozen" in the black hole. We show that the scalar field also has characteristics of dark matter shortly after Planck time, when we use a Big Bounce model. This model also presents an alternative to cosmological inflation with the possibility to solve the flatness and horizon problem and the problem of density fluctuations.

Attempts to find and quantify the supposed low entropy of organisms and its preservation are revised. Absolute entropy of the mixed components of non-living biomass (around -1.6 x 103 J K-1 L-1) is the reference to which other entropy decreases would be ascribed to life. Compartmentation of metabolites and departure from the equilibrium of metabolic reactions account for 1 and 40-50 J K-1 L-1, respectively, decreases of entropy and, though small, are distinctive features of living tissues. DNA and proteins do not supply significant decreases of thermodynamic entropy, but their low informational entropy is relevant for life and its evolution. No other living feature contributes significantly to the low entropy associated to life. The photosynthetic conversion of radiant energy to biomass energy accounts for the most of entropy (2.8 x 105 J K-1 carbon kg-1) produced by living beings. The comparative very low entropy produced in other processes (around 4.8 x102 J K-1 L-1 day-1 in human body) must be rapidly exported outside as heat to preserve the low entropy decreases due to compartmentation and non-equilibrium metabolism. Enzymes and genes are described whose control minimize the rate of production of entropy and could explain selective pressures in biological evolution and the rapid proliferation of cancer cells.

The present work evaluates the food effect on the absorption of rivaroxaban (Riva), a BCS II drug, from the orally administered commercial immediate-release tablet (Xarelto IR) using physiologically based pharmacokinetic (PBPK) and conventional in vitro- in vivo correlation (IVIVC) models. The bioavailability of Riva upon oral administration of Xarelto IR tablet is reported to exhibit a positive food effect. The PBPK model for Riva was developed and verified using the previously reported in vivo data for oral solution (5 and 10 mg) and Xarelto IR tablet (5 and 10 mg dose strength). Once the PBPK model was established, the in vivo performance of the tablet formulation with the higher dose strength (Xarelto IR tablet 20 mg in fasted and fed state) was predicted using the experimentally obtained data of in vitro permeability, biorelevant solubility and in vitro dynamic dissolution data using United States Pharmacopeia (USP) IV flow-through cell apparatus. In addition, the mathematical IVIVC model was developed using the in vitro dissolution and in vivo profile of 20 mg strength Xarelto IR tablet in fasted condition. Using the developed IVIVC model, the pharmacokinetic (PK) profile of the Xarelto IR tablet in fed condition was predicted and compared with the PK parameters obtained via the PBPK model. A virtual in vivo PK study was designed using a single-dose, 3-treatment cross-over trial in 50 subjects to predict the PK profile of the Xarelto® IR tablet in the fed state. Overall, the results obtained from the IVIVC model were found to be comparable with that from the PBPK model. The outcome from both the model pointed to the positive food effect on the in vivo profile of the Riva. The developed models thus can be effectively extended to establish bioequivalence for the marketed and novel complex formulations of Riva such as amorphous solid dispersions.

Transcriptional regulations have been widely studied as one of the main bridges between biology and other basic sciences as well as medicine. The traffic across it has been mostly unidirectional: chemistry and physics provided a lot of tools for biology, although the supply is now saturating. The traffic in opposite direction, the supply of subjects to develop chemistry and physics, has been only a little. However, if there are any, the supply will be at least from transcription, because the notion of chemical reaction is the strongest. This topic is aimed to increase the opposite traffic by introducing the forefront of physicochemical studies of transcription.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

We previously reported new superconductivity produced by an electrostatic field and a diffusion current in a semiconductor without refrigeration. In particular, the superconductivity was investigated theoretically and confirmed experimentally. Here, we determine that the derived superconducting quantum state can be reproduced in a capacitor. When circuits are formed with this new-type capacitor and diodes, a magnetic field is applied to the diodes’ depletion layer. The depletion layer is biased because of the conversion from the magnetic-field energy to electric-field energy, resulting in the diodes’ spontaneously emitting a current. Thus, the new-type capacitor is charged using no other energy source. This new phenomenon is described theoretically with assistance of initial experiments.

A graphene-containing LDH was prepared by re-hydration of the oxides produced by the calcination of an organic LDH. While the memory effect is a widely recognized effect on oxides produced by inorganic LDHs, it is unprecedented from the calcination/re-hydration of organic ones. Different temperatures (400, 600 and 1100 °C) were tested, on the basis of thermogravimetric data. Water instead of a carbonate solution was used for the re-hydration, with CO₂ available from water itself and/or air to induce a slower process with an easier and better intercalation of the carbonaceous species within the layers. The samples were characterized by X-ray Powder Diffraction (XRPD), IR and Raman spectroscopy and scanning electron microscopy (SEM). XRPD indicate the presence of carbonate LDH mixed with a layered phase with a larger d-spacing. IR confirmed that the prevailing anion is carbonate, coming from the water used for the re-hydration and/or air. Raman data indicated the presence of low-ordered graphenic species moieties and SEM the absence of separated graphene of graphitic sheets, suggesting an intimate mixing of the carbonaceous phase with reconstructed LDH. Organic LDHs gave better memory effect after calcination at 400 °C. Conversely, the graphenic species are observed after rehydration of the sample calcined at 600 °C with a reduced memory effect, demonstrating the interference of the carbonaceous phase with LDH reconstruction and the bonding with LDH layers to form a graphene-LDH nanocomposite.

The intracellular calcium dynamics in vascular endothelial cells (VECs) in response to wall shear stress (WSS) and/or adenosine triphosphate (ATP) have been commonly regarded as an important factor in regulating VEC function and behavior including proliferation, migration and apoptosis. However, the effects of time-varying ATP signals have been usually neglected in the past investigations in the field of VEC mechanobiology. In order to investigate the combined effects of WSS and dynamic ATP signals on the intracellular calcium dynamic in VECs, a Y-shaped microfluidic device, which can provide the cultured cells on the bottom of its mixing micro-channel with stimuli of WSS signal alone and different combinations of WSS and ATP signals in one single micro-channel, is proposed. Both numerical simulation and experimental studies verify the feasibility of its application. Cellular experimental results also suggest that a combination of WSS and ATP signals rather than a WSS signal alone might play a more significant role in VEC Ca²⁺ signal transduction induced by blood flow.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

It is often said in human society that it all starts from the mind, and this is true. The answer to the question “Why is it that pets require much fewer years to fully develop than humans?” could be headed to the Theory of Relativity and the perceived time according to the levels of instinct and rationality. It is perhaps no wonder that the French language translates the word “mind” as “l’esprit”, which also means “spirit” in the English language. Given that the Theory of Relativity applies to all physical matter, the theory applies to chemistry, biology and psychology as well. The level of instinct is proportional with the perceived speed of time and implicitly, to the speed of time itself for the whole organism, given that the nervous system coordinates all bodily functions. A pet may experience a few years as humans experience over a decade, making their perceived lifetime to be approximately equal to the human’s. The same applies to the perception of space and its components. This aspect would emphasise upon the fact that all life on Earth shows the same degree of value with regards to uniqueness. Nevertheless, the values represented by the hierarchy of competences among living organisms at the same time differs based on species. Honour of uniqueness and hierarchy of competences represent two scientific concepts that never overcross. As a result, there is no evidence to suggest that scientific facts as such constitute a form of contradiction to philosophical and religious ideas, given that religion refers to animals as companions of humans. With regards to the clock of the living organism; there are three kinds of clocks in a living organism: the emotional clock, the cognitive clock and the molecular clock. These three categories actually constitute the temporal layers of our dimension, so they are in a relationship of interdependence. When one has a feeling that time is slower or quicker, they are not fully experiencing that change in the time speed, but only partially. And one can profoundly experience the change of perceived time speed when they experience profound feelings, which sweep them away from reality. Complete, deep mental focus can bring about this profound change in perception, which will make the individual feel as if they are in a different form of reality. When one is more instinctive, the person in cause perceives time as slower and sees more opportunities within the same frame of time and space. When one experiences the “Fight or flight” mode, the person in the cause finds themselves to be in danger and has two options; to try to prevail over the danger or to flee it. Whilst experiencing such a mode, people are much more alert and therefore, time passes more slowly and the physical space dilates. When people are relaxed, however, time and space become smaller, and when they are in a deep state of resting, they become very small. And where there is a smaller dimension, there is a greater speed, just as the circulating air gains speed when it crosses narrow passages.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

1960s Europe saw a large number of residential neighborhoods built to house those migrating from the countryside. Today, more than 50 years later, these neighborhoods suffer high levels of functional, social, and technical obsolescence. In response to this, University of Seville developed the Aura Strategy as an intervention methodology to find global solutions to issues in outdated neighborhoods. To provide visibility to this aspect of the Aura strategy, the retrofit proposal presented in this article provides a solution to improve the roofing of buildings in a case study neighborhood (Polígono de San Pablo, Seville) and an analysis of the results in terms of energy and financial savings for local residents. The results show that for a population of roughly 18,000 (in 2018), net savings, including energy and retrofitting costs, ranging from nearly 6.5 to over 8.6 million can be made over the 20-year life cycle span. Likewise, the results obtained on the reduction of thermal loads indicate a 72% decrease in energy consumption, equivalent to a saving of close to 4,500 tons of greenhouse gas emissions for the district and the entire life cycle time period, with the consequent benefits on the impact on air quality and and the fight against climate change. climate change.

Sous-vide is a process in which food is vacuum-sealed and prepared in a water bath, heated to a precise temperature, and circulated in a sous-vide machine. This cooking technique is increasingly common in homes and catering establishments due to its simplicity and affordability. However, manufacturers' and chefs' recommendations for low-temperature and long-term sous-vide cooking in media raise food safety concerns, particularly when preparing beef tenderloin. In this study, Salmonella enterica was found to be inactivated by heat and sage essential oil (EO) in beef tenderloin from musculus psoas major that had undergone sous-vide processing. To determine whether heat treatment was likely to increase the sous-vide efficiency, S. enterica and sage EO were mixed. After being vacuum-packed and injected with S. enterica, the samples were cooked sous-vide for the prescribed time at 50, 55, 60, or 65 °C. On days 1, 3, and 6, the amounts of S. enterica, total bacteria, and coliform bacteria were measured in both groups of sous vide beef tenderloin. Mass spectrometry was used to identify bacterial strains on various days and categories. Each day that was measured, the test group exposed to a temperature of 50 °C for 5 minutes had a higher number of all microbiota. The most isolated microorganisms from the control and treated groups were Pseudomonas fragi, and in the treated group also S. enterica. It has been shown that adding sage essence oil (EO) in combination with the sous-vide gastronomic method leads to the stabilization and safety of beef tenderloin.

The functional capacity of the cervical spine plays a central role in healthy living. This study evaluated and created a comprehensive strength, range of motion (ROM), and musculoskeletal pain profile of the cervical spine in young adults. 60 physically active individuals (30 males/30 females; 19-24 year-old) participated in the study. Cervical ROM (forward flexion, extension, lateral flexion, and rotation), maximal isometric strength (forward flexion, extension, lateral flexion), and musculoskeletal pains were assessed using an electronic goniometer, a handheld dynamometer, and the Nordic questionnaire, respectively. Data analysis revealed that: a) fe-males had higher ROM values, during extension and lateral flexion, than males (p<0.05), b) males had higher absolute strength values than females in all movement directions, higher rela-tive strength values/body mass (at forward flexion) and flexion/extension ratio values (p<0.05), c) ROM and strength values were not significantly different between right-left sides (p>0.05), d) a great proportion (43.3%) of the participants had cervical pains (no sex-related differences) and e) cervical strength showed significant small negative correlation with pains (p<0.05; r=-0.225 to -0.345). The reference values created may be used by health and fitness professionals to exten-sively evaluate the cervical spine and to design specific exercise programs for injury prevention and rehabilitation.

In a p-uniformly convex and uniformly smooth Banach space, let the pair of variational inequality and fixed point problems (VIFPPs) consist of two variational inequality problems (VIPs) involving two uniformly continuous and pseudomonotone mappings and two fixed point problems implicating two uniformly continuous and Bregman relatively asymptotically nonexpansive mappings. This article designs two parallel subgradient-like extragradient algorithms with inertial effect for solving this pair of VIFPPs, where each algorithm consists of two parts which are of symmetric structure mutually. Under mild registrations, we prove weak and strong convergence of the suggested algorithms to a common solution of this pair of VIFPPs, respectively. Lastly, an illustrative example is furnished to verify the applicability and implementability of our proposed approaches.

This study selected the Yangtze River Delta urban agglomeration as the research area, combining it with the current situation of the transportation development of the Yangtze River Delta urban agglomeration to construct the urban agglomeration transportation integration index system and evaluate the development status of the Yangtze River Delta urban agglomeration transportation integration. The study examined the influence mechanism of transportation infrastructure on service industry agglomeration. The results are as follows: (1) From 2011–2020, the Yangtze River Delta urban agglomeration’s transportation integration index showed a clear upward trend. (2)The development of transport integration in urban agglomerations has heterogeneous effects on local service agglomeration. The development of the integration level of local transportation has a certain inhibitory effect on the agglomeration of local service industry. The transportation integration of the Yangtze River Delta urban agglomeration plays an important role in promoting the agglomeration of local wholesale and retail industry, transportation, storage and postal services. (3) The transportation integration of urban agglomeration can affect the agglomeration of service industry through the knowledge spillover brought by the free flow of various factors. The knowledge spillover effect caused by local transportation integration can promote the agglomeration of local service industry to a certain extent. The Yangtze River Delta urban agglomeration needs to accelerate the construction of trans-provincial and trans-municipal transportation infrastructure, and further improve the connectivity level of the urban agglomeration, so as to promote the integrated development of high-quality transportation in the Yangtze River Delta urban agglomeration.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

The impact of snow darkening by deposition of light absorbing aerosols (LAAs) on snow cover over the Himalaya-Tibetan-Plateau (HTP) and influence on the Asian monsoon are investigated using the NASA Goddard Earth Observing System Model Version 5 (GEOS-5). We find that during April-May-June, deposition of LAAs on snow leads to a reduction in surface albedo, initiating a sequence of feedback processes, starting with increased surface solar radiation, rapid snowmelt in HTP and warming of the surface and upper troposphere, followed by enhanced low-level southwesterlies and increased dust loading over the Himalayas-Indo-Gangetic Plain. The warming is amplified by increased dust aerosol heating, and subsequently amplified by latent heating from enhanced precipitation over the Himalaya foothills and northern India, via the Elevated Heat Pump (EHP) effect during June-July-August. The reduced snow cover in the HTP anchors the enhanced heating over the Tibetan Plateau and its southern slopes, in conjunction with an enhancement of the Tibetan Anticyclone, and the development of an anomalous Rossby wavetrain over East Asia, leading to weakening of the subtropical westerly jet, and northward displacement and intensification of the Mei-Yu rainbelt. Our results suggest that atmosphere-land heating by LAAs, particularly desert dust play a fundamental role in physical processes underpinning the snow-monsoon relationship proposed by Blandford more than a century ago.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

Ultra high molecular weight polyethylene (UHMWPE) is a thermoplastic high-performance polymer in high demand for biomedicine, ship and machine building, anthropomorphic robots and smart prostheses. Highly oriented UHMWPE fibers possess record specific strength and may also be used for the fabrication of self-reinforced PE-PE composites (SRPEC). The temperature evolution study of the small-angle X-ray scattering (SAXS) signature of the supramolecular structure of UHMWPE can help reveal their important role in the mechanism of the shape memory effect in SRPEC. The laboratory SAXS–WAXS beamline XEUSS 3.0 was used for in situ studies of the nanostructure parameters in unidirectional SRPEC. Namely, the radius of gyration and the dimensionality factor were extracted from 2D SAXS patterns using several fitting algorithms. Significant changes of these parameters occurred in temperature ranges that correspond to the initiation of the shape memory effect and melting. The relationship between the material anisotropy and 2D SAXS patterns are discussed in the context of the supramolecular structure evolution.

The atomic nucleus contains protons and neutrons surrounded by a structured electron cloud. Some combinations of protons and neutrons induce the nucleus to behave like a microscopic magnet, possessing a unique magnitude and orientation known as the nuclear magnetic moment (µ). When the numbers of protons and neutrons are both even then µ=0, but otherwise each nu-clide’s nuclear magnetic moment is unique. A second unique nuclear physical property relates to the nucleon binding energy (BE), which can be thought of as the energy between protons and neu-trons bound within the nucleus. The sequence of stable nuclides increases one nucleon at a time through 36Ar. The binding energy associated with the addition of each successive nucleon (∆BE) through this progression is unique. The hypothesis here is that the unique non-zero magnetic mo-ment and ∆ binding energy of each nuclide derive from its respective microscopic nuclear struc-ture, analogous to the way that the atomic physical properties of an element ultimately derive from its unique electron orbital structure. By extension, the identification of nuclear periodic pat-terns might eventually inform a theory of nuclear structure. The light, stable nuclides through 36Ar were arranged in ascending order according to atomic mass, and their nuclear magnetic mo-ments and binding energies were evaluated for periodic patterns. Fixed-period lengths from 4 through 18 nuclides per period were considered. These fixed periods, each of equal length, were stacked one upon the other and analyzed for vertical trends. The best evidence of periodicity in both µ and ∆BE converges precisely at the fixed 12-nuclide period. Implications for nuclear structure are discussed.

In mobile applications such as geomagnetic surveying, two major effects hamper the use of optically pumped magnetometers: dead zones, sensor orientations where the sensors signal amplitude drops; and heading errors, a dependence of the measured magnetic field value on the sensor orientation. We present a concept for an omnidirectional magnetometer to overcome both these effects. The sensor uses two cesium vapor cells, interrogated by circularly-polarized amplitude-modulated laser light split into two beams running perpendicular to each other. This configuration is experimentally investigated using a setup wherein the laser beam and magnetic field direction can be freely adjusted relative to each other within a magnetically shielded environment. We demonstrate that a dead-zone free magnetometer can be realized with nearly isotropic magnetic-field sensitivity. While in the current configuration we observe heading errors emerging from light shifts and due to the nonlinear Zeeman effect, we introduce a straightforward approach to suppress these systematic effects in an advanced sensor realisation.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

The enzyme N-acetylgalactosamine-4-sulfatase (Arylsulfatase B; ARSB) was originally identified as a lysosomal enzyme which was deficient in Mucopolysaccharidosis VI (MPS VI; Maroteaux-Lamy Syndrome). Newly directed attention to the impact of ARSB in human pathobiology indicates a broader, more pervasive effect, encompassing roles as a tumor suppressor, transcriptional mediator, redox switch, and regulator of intracellular and extracellular-cell signaling. By controlling the degradation of chondroitin 4-sulfate and dermatan sulfate by removal or failure to remove the 4-sulfate residue at the non-reducing end of the sulfated glycosaminoglycan chain, ARSB modifies the binding or release of critical molecules into the cell milieu. These molecules, such as galectin-3 and SHP-2, in turn, influence crucial cellular processes and events which determine cell fate. Identification of ARSB at the cell membrane and in the nucleus expands perception of the potential impact of decline in ARSB activity. Regulation of availability of sulfate from chondroitin 4-sulfate and dermatan sulfate may also affect sulfate assimilation and production of vital molecules, including glutathione and cysteine. Increased attention to ARSB in mammalian cells may help to integrate and deepen our understanding of diverse biological phenomenon and to approach human diseases with new insights.

Maxwell’s equations are valid only for a stationary observation point, therefore, to adequately describe real processes so far we have had to move to a moving reference frame. This paper presents the equations of electrodynamics for the moving observation point, it is shown that plane and spherical electromagnetic waves are their solutions, while the spherical wave propagates only outward, which cannot be said about Maxwell’s equations. The fields of uniformly moving charges are also solutions of the equations. Now there is no need to move to a moving reference frame, to use four-dimensional space and covariant form of equations. The question of finding a universal form of the equations that allows a solution in the form of the field of an arbitrarily moving charge remains open. This raises the question of the existence of a two-parameter group of transformations of electromagnetic fields along with the known one-parameter group has been posed. The phenomena derived from the equations, which make an additional contribution to the phase overrun in the Aharonov-Bohm effect are considered. The equation of motion of a charged particle in an electromagnetic field without simplifying approximations is considered, which allows us to take into account the radiation effects. It is shown that the fields in a moving observation point depend on its velocity and acceleration. In particular, although in a constant uniform electric field a force qE acts on a motionless charged particle, but on the same motionless but not fixed particle the force 4/3qE acts already, because it has a nonzero acceleration and the electric field at this point is larger. As the speed increases, the field decreases, and when it reaches the speed of light, when the particle stops accelerating, the force again becomes equal to qE The principle of operation of an unconventional alternator in a constant electric field and its corresponding engine, as well as new types of direct and impulse current generators, predicted by the equations, are described.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

Our previous in vitro reports showed that crude extract prepared with 50% ethanol (ethanol crude extract, ECE) from Mongolian oak cups possessed excellent antioxidant capacities as well as inhibitory activities against α-glucosidase, α-amylase and protein glycation caused by its enrichment in phenolics, including mainly ellagic acid, kaempferol and their derivatives. Nevertheless, few in vivo studies on antidiabetic activities of these phenolics were conducted. The present study investigated hypoglycemic effects with normal and diabetic rats being administrated orally without or with ECE at 200 and 800 mg/kg for 15 days. In normal rats, no significant differences were exhibited after ECE administration in body weight, fasting blood glucose level, levels of chelesterol, triglyceride, LDL and AST in serum, organ indexes, and levels of GSH and MDA in organs. In diabetic rats, the fasting blood glucose level, indexes of heart and liver, and levels of chelesterol and triglyceride in serum and MDA in heart tissue were significantly decreased. Moreover, HDL levels in serum and SOD activities in the four organs of diabetic rats were significantly improved after ECE administration at 800 mg/kg. Thus, in addition to inhibiting α-glucosidase, α-amylase and protein glycation reported previously, oak cups might contain novel dietary phytonutrients in preventing abnormal changes in blood glucose and lipid profile and attenuating oxidant stress in vivo. The results also implied that it is ellagic acid, kaempferol and their derivatives enriched in ECE that might play vital roles in managing type 1 as well as type 2 diabetes.

Using of the organic base tetramethylammonium hydroxides (TMAH) is a viable, cheap and fast route, for the MgZnAl-LDH type materials synthesis by both co-precipitation and mechano-chemical methods. TMAH provided several advantages as smaller quantity of water required in the washing step compared to the use of inorganic alkalis, prevention of LDH contamination with alkali cations, acting as template molecule in texture tailoring along with disadvantages as its presence in small quantities in the resulting layered materials. Regardless the use of organic / inorganic bases and co-precipitation / mechano-chemical methods, zincite stable phase was found in all the synthesized solids. The basicity of catalysts followed the trend: mixed oxides &gt; reconstructed &gt; parent LDH. The memory effect of LDH is supported only by the presence of Mg and Al cations, while Zn remains as zincite stable phase. The catalytic activities for Claisen-Schmidt condensation of benzaldehyde with cyclohexanone provided values higher than 90% after 2h, with a total selectivity in 2,6-dibenzylidenecyclohexanone, while in self-condensation of cyclohexanone no more than 7.29% after 5h. These behaviors depended on catalysts basicity as well as the planar rigidity of the compound.

The purposes of this study are based upon the theory of planned behavior (TPB) to examine the impact of past experiences of contract farming on selecting a specific type of contract farming in the future and then compare different psychological factors in the TPB for different potential contract farmer statuses. These statuses include homesteaders, farmers from cooperative farms, farmers from production and sales teams, professional farmers, and brokers. The impact of factors in the TPB for a particular contract type on potential contract farmers is further to compute. To this end, data are collected in three major sweet potato production areas in Taiwan. The results show that the farmers’ past contract farming experience does not influence the selection of the contract in the future. As for the selection of contract type, strengthening the perception and motivating the behavioral intention of contract farming for cooperative farms will increase the probability of selecting an unclassified sweet potato size contract. On the other hand, enhancing perceived behavioral control factors and behavioral intention factors for professional farmers and brokers is apt to have a relatively high probability of selecting those types involving the highest amount or the best price to obtain the best deal.

Constructing an innovation system centered on new-quality productivity is key to achieving China's technological independence and high-quality development, especially against the backdrop of rapid advancements in artificial intelligence. This article utilizes provincial panel data from China spanning 2010 to 2022 and applies kernel density estimation and the Moran's I index to study the spatiotemporal evolution of artificial intelligence and new-quality productivity. The findings indicate a clustering trend in the development of both factors across regions. Causal empirical analysis using a two-way fixed-effects model reveals that artificial intelligence positively influences new-quality productivity, with conclusions validated by robustness and endogeneity tests.

The application of non-uniform spiral gratings to control structure, topological parameters and propagation of orbital angular momentum (OAM) beams was studied experimentally with coherent near-infrared light. Adapted digital spiral grating structures were programmed into the phase map of a high-resolution liquid-crystal-on-silicon spatial light modulator (LCoS-SLM). It is shown that characteristic spatio-spectral anomalies related to Gouy phase shift can be used as pointers to quantify rotational beam properties. Depending on sign and gradient of spatially variable periods of chirped spiral gratings (CSG), variations of rotation angle and angular velocity as a function of propagation distance were measured. Propagation-dependent self-torque is introduced in analogy to known local self-torque phenomena of OAM beams as obtained by the superposition of temporally chirped or phase modulated wavepackets.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

The article considers an internal boundary value problem of the distribution of an electrostatic field in a lens formed by two identical semi-infinite circular cylinders coaxially located inside an infinite external cylinder. The problem is reduced to solving a system of singular Wiener-Hopf integral equations, which is further solved by the Wiener-Hopf method using factorized Bessel functions. Solutions to the problem for each region inside the infinite outer cylinder are presented as exponentially converging series in terms of eigenfunctions and eigenvalues.

The electronic cigarette or e-cigarette is the new alternative method to deliver nicotine. In 2007, the United States introduced vaping devices on the market. Due to their attractive taste and lack of adverse effects, these vaping devices have gained popularity among youth and adults. However, there has been increasing evidence that vaping can cause severe lung injury, and these devices release toxic chemicals into the body. E-cigarettes are recognized as a global threat to public health. Nicotine, the most prevalent chemical in vaping devices, is associated with neurological problems and cognitive decline. Long-term use of e-cigarettes can cause adverse health problems, including respiratory illnesses, asthma, bronchitis, and lung inflammation. In 2019, the Centers for Disease Control and Prevention (CDC) officially declared vaping-associated illness EVALI (e-cigarette or Vaping Product Associated Lung Injury). The US Surgeon General published an alarm in December 2016 that e-cigarette consumption among adolescents and teens in the US is a "major public health concern" and that more young people are now vaping than smoking traditional cigarettes and cigars. Since its commercial introduction in 2003, modern electronic cigarettes (or E-cigarette s) have become increasingly popular with smokers, non-smokers, and those who used to smoke who have switched to them. With such a rise in consumption, people are becoming more aware of the irritating, harmful, and perhaps cancer-causing effects on the lungs. (Chadi et al., 2019; Dinardo & Rome, 2019; Lyzwinski et al., 2022; Marrocco et al., 2022; O’Callaghan et al., 2022)

This study investigates the efficiency of a biogas-powered cooling system through the utilization of energy and exergy calculations. Biogas, which can be generated and stored in small-scale plants as needed, serves as a viable fuel source for absorption cooling systems. The present research focuses on the biogas consumption of a triple-effect absorption cooling system, specifically designed to supply a fixed cooling load of 100 kW under varying operational conditions. The study highlights the COP (Coefficient of Performance) and ECOP (Exergetic Coefficient of Performance) values of the system, along with the exergy destruction rates of its individual components, at the optimal temperatures of operation. Furthermore, to determine the necessary biogas consumption, the study explores the establishment of dedicated farms for various animal species, ensuring an adequate number of animals for biogas production. The findings reveal a COP of 1.78 and an ECOP of 35.4% at the optimized operating temperatures. The minimum mass flow rate of biogas is determined to be 0.0034 kg/s, facilitating the operation of the boiler with a methane content of 65%. The study concludes that a total of 290 head of cattle is required to generate the annual biogas consumption necessary for the cooling system. Also, number of the cattle is enough to establish 284 biogas plants in Bursa province in Türkiye.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

This paper proposes a method of extracting energy from zero-point energy and evaluates the amount of energy gained. In addition, this electric circuit-based approach exhibits the Meissner effect, suggesting a new type of superconductivity that does not require refrigeration. The proposed method can provide extremely large amounts of energy, which is more than a conventional power station, without consuming fossil fuels or emitting radiation. Thus, it has the potential to solve the global energy problem. It involves preparing two electric loops containing diodes and connecting the loops together with current sources. The diodes are oriented in the same direction within each loop but in opposite directions in different loops. With this setup, the currents from the current sources build iteratively within the loops, resulting in large output currents. Our numerical analysis indicates that extremely large electric potentials are produced, which in turn yield large output currents. In addition, we confirm numerically that the voltage is zero around a loop and show analytically that the Meissner effect is present, proving the existence of a new type of superconductivity. Furthermore, when we introduce induction coils to not break the loop’s symmetry, they store extremely large amounts of energy and we can thus obtain energy from them via discharge currents.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

This paper presents an in-depth study of the stress wave behavior propagating in a Rayleigh–Love rod with a sudden cross-sectional area change. The analytical solutions of stress waves are derived for the reflection and transmission propagation behavior at the interface of the cross-sectional area change in the rod, considering inertia and Poisson’s effects. Examples solved by the finite element method are provided to verify the correctness of the analytical results. In addition to the forward analysis of Rayleigh–Love wave propagation in rods impacted by a striker rod, a nondestructive testing method is proposed to conduct the defect assessment in the rod type of the structure component with a sudden cross-sectional area change within a cover medium by using the measured signals at the measurable zone of the rod to be inspected.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

J/ψ, a charmonium bound state made of a charm and an anti-charm quark, has been discovered in the 1970s and confirmed the quark model. Because the mass of charms quarks is significantly above the Quantum Chromodynamics (QCD) scale ΛQCD, charmonia are considered as excellent probes to test perturbative Quantum Chromodynamics (pQCD) calculations. Over the past decades, they have been studied extensively at different high energy colliders. However, their production mechanisms, which involves multiple scales, are still not very well understood. Recently, in high multiplicity p+p collisions at RHIC and at the LHC, a significant enhancement of J/ψ production yield has been observed, which suggests a strong contribution from the Multi-Parton Interaction (MPI). This is different from the traditional pQCD picture where charm quark pairs are produced from a single hard scattering between partons in p+p collisions. In this work, we will report the J/ψ normalized production yield as a function of normalized charged particle multiplicity over a board range of rapidity and event multiplicity in the J/ψ→μ+μ− channel with PHENIX Run 15 p+p data at \sqrt{s}=200 GeV. The results are compared with PYTHIA 8 simulations with the MPI option on and off. Finally, the outlooks of J/ψ in p+Au and Au+p collisions along with Color Glass Condensate (CGC) predictions and of multiplicity dependent ψ(2S)/J/ψ ratio in p+p data will be briefly discussed.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

The principle of the constancy of the velocity of light, which stated that the light velocity is invariant to the motion of the emitter, was well established and directly proven by experiments. Interestingly, the further assumption that the light velocity is independent of the motion of the observer was, arguably, never directly proven by any experiment for a century. This paper proposed the design of two experiments to directly test this assumption, which tried to address some perceived technical difficulty in such experiments. One is to directly measure the light speed as to moving sensors. The experiment setup is designed in such a way that the concerns of time synchronization and dilation can be avoided. Another experiment is to test the isotropy of the light speed to a moving particle in the electromagnetic accelerator by measuring the momentum to acceleration ratio. The experiment result, if positive, will provide direct and solid proof of the assumption. Otherwise, it may imply a need for further investigation. Since the light speed invariance to moving observers is a key assumption of some fundamental physical theory, either way, the experiments will have significant meanings.

Societies around the world face serious energy problems related to the consumption of fossil fuels and the emission of dangerous radiation. To solve these problems, a new superconductor exhibiting a critical temperature higher than room temperature has been pursued but not achieved. This paper proposes a new energy generation system based on a circuit approach. Secondary to this process, a new type of superconductivity without refrigeration is demonstrated. In our previous paper [1], this system was proposed, but it did not describe the underlying theory in detail and did not mention an actual method to generate energy from the system. The present paper describes the theory of the existence of divergent current density and new superconductivity with no refrigeration. Moreover, the present paper proposes a method for extracting energy from the system by employing a voltage-controlled current source (i.e., a voltage–current converting method).The principle of the system is based on a circuit of two loops and independent current sources. First, the two electric loops are prepared, each with 4 diodes, where the diodes are oriented in the same direction within each loop, but their direction is opposite from loop to loop; four independent current sources connect the loops. In this circuit system, current is added iteratively as it flows along the loop according to Kirchhoff’s circuit law. As a result, a large current and electric potential are present along the loop. To confirm that this system works properly, it is necessary to demonstrate the presence of divergent currents in the transient state, and to do this, the present paper employs the Dirac equation and Lorentz conservation. Electric circuit software is employed to demonstrate that the presented method generates energy actually from our system.Our results confirm the presence of divergent current at a connected point of an independent current source in the transient state. Moreover, in the steady state, the theory demonstrates the Meissner effect (i.e., a London equation) and a new type of macroscopic wave function and condensation. For an initial small input current of 0.1 μA, the simulation reveals a large generating current of 7 kA and electric power of 10¹¹ W, which is much larger than unit of power from an average thermal power station; moreover, the system presents with superconducting electrical transport conditions.The present study is significant because it demonstrates theoretically the existence of divergent current density and a new type of superconductivity requiring no refrigeration. Secondly, the simulations show the generation of a large energy density that can be obtained in a small laboratory room with minimal cost.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.