Several copolymer hydrogels were prepared from free radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with itaconic acid (IA). A series of Poly(2-hydroxyethyl methacrylate-co-itaconic acid) hydrogel, poly(HEMA-co-IA) were prepared at different feed monomer ratio using ammonium persulfate (APS) initiators in water at 70°C. The phytodrug 2,4-dichlorophenoxy acetic acid (2,4-D) were grafted to Poly(HEMA-co-IA) by esterification reaction. In addition, swelling behavior (Wt%) was studied at different pH. The hydrolysis of Poly(HEMA-co-IA)-2,4-D showed that the release of the bioactive compounds in aqueous phase, using Liquid-phase polymer-based retention (LPR) ultrafiltration system is dependent on the hydrophilic character as well as on pH value. The acid-hydrolysis of the herbicide from the conjugates follows a first order kinetics, showing higher kinetic constants as the pH increases. The base-catalyzed hydrolysis reaction of the herbicide follows a zero order kinetic, where the basic medium acts as a catalyst accelerating the release rate of the herbicide, showing higher kinetic constants as the pH increases. The differences in the release rates found for the hydrogel-herbicide at different pH can be correlated with the difference in their swelling capacity, where the release rate generally increases with an increase in the swelling capacity from water solution at higher pH. The study of the release process revealed that all samples in distilled water at pH 10 are representative of agricultural systems, showed first-order swelling kinetics and an absorption capacity that conforms to the parameters for hydrogels for agricultural application, which supports their potential for these purposes.

Interferon alpha (IFNα) is a protein drug used to treat viral infections and cancer diseases. Due to its poor stability in the gastrointestinal tract, only parenteral administration ensures bioavailability, which is associated with severe side effects. We hypothesized that the nanoencapsulation of IFNα within nanoparticles of the mucoadhesive polysaccharide chitosan would improve the oral bioavailability of this drug. In this work, we produced IFNα-loaded chitosan nanoparticles by the ionotropic gelation method. Their size, size distribution and concentration were characterized by dynamic light scattering and nanoparticle tracking analysis. After confirming their good cell compatibility in Caco-2 and WISH cells, the permeability of unmodified and PEGylated nanoparticles was measured in monoculture (Caco-2) and co-culture (Caco-2/HT29-MTX) cell monolayers. Results indicated that the nanoparticles cross the intestinal epithelium mainly by the paracellular route. Finally, the oral pharmacokinetics in BalbC mice of nanoencapsulated IFNα revealed that it was absorbed reaching an area-under-the-curve of 56.9 pg.h/mL.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

The inner walls of drinking water distribution system (DWDS) are expected to be clean to ensure a safe quality of drinking water. In reality, complex physical, chemical and biological processes take place when water comes into contact with the pipe surface. This paper describes the impact of leaching different compounds from the water supply pipes into the drinking water and subsequent risks. Among these compounds there are heavy metals. It is necessary to prevent these metals to get into the DWDS. Those compounds are susceptible to impact the quality of the water delivered to population either by leaching dangerous chemicals into the water or by enhancing the development of microorganism growth on the pipe surface. The corrosion process of different pipes materials, scale formation mechanisms and the impact of bacteria formed in corrosion layers are discussed. Water treatment processes and the pipe materials also affect the water composition. Pipes materials act differently in the flowing and stagnation conditions. Also, they age differently (e.g metal based pipes are subjected to corrosion while polymer based pipes have a decreased mechanical resistance) and are susceptible to enhance bacterial film formation. This review helps to clarify what are the possible sources of compounds responsible for drinking water quality degradation. Also, it gives guidance on the measures that are needed to maintain a stable and safe drinking water quality.

Low charge density nanometric ions were recently shown to bind strongly to neutral hydrated matter in aqueous solution. This phenomenon, called (super-)chaotropic effect, arises from the partial dehydration of both, the nano-ion and the solute, leading to a high gain in enthalpy. Here, we investigate the chaotropic effect of the polyoxometalate α-PW12O403- on the triblock copolymer P84: (EO)19(PO)43(EO)19 with (EO)19 the polyethoxylated and (PO)43 the polypropoxylated chains. The combination of phase diagrams, spectroscopic (nuclear magnetic resonance) and scattering (small angle neutron/X-ray scattering) techniques reveals that (i) below the micellization temperature of P84, PW12O403- exclusively binds to the propylene oxide moiety of P84 unimers and (ii) above the micellization temperature, PW12O403- mostly adsorbs on the ethylene oxide micellar corona. The preferential binding of the PW12O403- to the PPO chain over the PEO chains suggests that the binding is driven by the chaotropic effect and reinforced by the hydrophobic effect. At higher temperatures, the copolymer micellization leads to the displacement of PW12O403- from the PPO chain to the PEO chains. This study deepens the understanding of the subtle interplay between the chaotropic and hydrophobic effects in complex salt-organic matter solutions.

Viscoelastic relaxation measurements on Stirene-Butadiene rubbers (SBR) doped with Carbon Nanotube (CNT) at different concentration show the time-temperature superposition (TTS). This process is described in terms of the Mode Coupling Theory (MCT) approaches to the viscoelasticity by considering the frequency behavior of the loss modulus E”(ω), and shown that the corresponding TTS is linked to a (ω)1/2 decay. From of the analysis of the obtained data we observe that the interaction between the SBR and CNT determine different decays different decays according to their concentration. The rubbers with the lowest CNT concentration are only characterized, in the studied T-range, by a fragile glass forming behavior. Whereas those at the highest ones instead show, at a specific temperature TL, a crossover towards a pure Arrhenius, that according to the MCT, indicates the presence of a kinetic glass transition (KGT); where the system response functions are characterized by scaling behaviors.

Computational modeling (CM) is a versatile scientific methodology used to examine the properties and behavior of complex systems, such as polymeric materials for biomedical bioengineering. CM has emerged as a primary tool for predicting, setting up, and interpreting experimental results. Integrating in silico and in vitro experiments accelerates scientific advancements, yielding quicker results at a reduced cost. While CM is a mature discipline, its recent prominence in Bio-medical Engineering for biopolymer materials has recently gained prominence. In biopolymer biomedical engineering, CM focuses on three key research areas: A) Computer-aided design (CAD/CAM), B) Finite Element Analysis, and C) Molecular Dynamic Simulations. This review centers on Molecular Dynamics (MD) simulations in biopolymers, analyzing structural, functional, and evolutionary aspects of biomolecular systems over time. MD simulations solve Newton's equations of motion for all-atom systems, generating spatial trajectories for each atom, providing insights into properties like water absorption on biopolymer surfaces and interactions with solid surfaces, crucial for biomaterial assessment. This review offers readers a comprehensive overview of the diverse applications of Molecular Dynamics (MD) simulations on biopolymers. Furthermore, it emphasizes the flexibility, robustness, and synergistic relationship between in silico and experimental techniques.

Cancer, characterized by abnormal cell proliferation driven by genetic mutations, remains a significant health challenge. Tailoring effective therapies depends on factors like tumor location, grade, and stage, alongside patient condition. Leveraging Nano-carrier encapsulated drugs offers a promising avenue, as they accumulate preferentially at tumor sites, enhancing therapeutic efficacy while mitigating side effects. Polymeric Nano-carriers, with their customizable properties, further optimize drug delivery efficiency and specificity. Incorporating active targeting ligands such as antibodies, carbohydrates, peptides, folates, and aptamers-onto polymeric nanoparticle surfaces through techniques like functionalization, adsorption, and conjugation plays a pivotal role in directing therapeutic agents to tumor cells. Consequently, polymeric nanoparticles emerge as the carrier of choice for delivering drugs to various tumor types, including breast, colon, lung, prostate, liver, and spleen tumors.

Molecular engineering research is the fundamental way and the only way for the development of biomaterials. Based on molecular engineering, the biocompatibility of natural conformation and polymer biomaterials was studied. In this paper, we discuss that natural conformation is the basis of protein biological function, and that the synergistic action of peptide chain and side group is the motive force for protein to construct natural conformation and complete biological function. On the basis of the influence of the adsorption of polymer biomaterials on the natural conformation of proteins, the relationship between biocompatibility of biomaterials and protein conformation is further explained. Studies have shown that bismuth molecular materials can only be applied in the market and have their functionality if they have good biocompatibility. Therefore, the biocompatibility evaluation of new materials has important practical significance.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

In recent years, the field of drug delivery has seen a significant shift towards the exploration and utilisation of nanoparticles (NPs) as versatile carriers for therapeutic agents. With its ability to provide exact control over NPs' characteristics, microfluidics has emerged as a potent platform for the efficient and controlled synthesis of NPs. Microfluidic devices designed for precise fluid ma-nipulation at the micro-scale offer a unique platform for tailoring NP properties, enabling en-hanced control over NP properties such as size, morphology and size distribution while ensuring high batch-to-batch reproducibility. Microfluidics can be used to produce liposomes, solid lipid nanoparticles, polymer-based NPs and lipid-polymer hybrid NPs, as well as a variety of inorganic NPs such as silica, metal, metal oxide, quantum dots and carbon-based NPs, offering precise control over composition and surface properties. Its unique precision in tailoring NP properties holds great promise for advancing NP-based drug delivery systems in both clinical and industrial set-tings. Although challenges with large-scale production still remain, microfluidics offers a trans-formative approach to NP synthesis. In this review, starting from the historical development of microfluidic systems, the materials used to create the systems, microfabrication methods and system components will be discussed in order to provide the reader with an overview of micro-fluidic systems. In the following, studies on the fabrication of nanoparticles such as lipid NPs, polymeric NPs and inorganic NPs in microfluidic devices are included.

Carbon nanodots (CNDs) have garnered significant attention as viable drug delivery vehicles in recent years, especially in the field of phytomedicine. Although there is much promise for therapeutic applications with phytomedicine, its effectiveness is frequently restricted by its low solubility, stability, and bioavailability. This paper offers a thorough synopsis of the developing field of phytomedicine drug delivery based on CND. It explores CND synthesis processes, surface functionalization strategies, and structural and optical characteristics. Additionally, the advantages and difficulties of phytomedicine are examined, with a focus on the contribution of drug delivery methods to the increased effectiveness of phytomedicine. The applications of CNDs in drug delivery are also included in the review, along with the mechanisms that underlie their improved drug delivery capabilities. Additionally, it looks at controlled release methods, stability augmentation, and phytomedicine loading tactics onto CNDs. The potential of polymeric carbon nanodots in drug delivery is also covered, along with difficulties and prospective directions going forward, such as resolving toxicity and biocompatibility issues. In summary, the present review highlights the encouraging contribution of CNDs to the field of drug delivery, specifically in enhancing the potential of phytomedicine for therapeutic purposes.

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

In this study we assessed the electrical and optical behavior of semiconductor hybrid films fabricate from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically by means of Infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology, besides; the PS matrix allows the crystallization of the porphin, while the PMMA promotes the amorphous structure in CuP. The polymeric matrix also has an effect on the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV) and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is around 0.01 A for PS:CuP film, while for PMMA:CuP film it is 0.0015 A. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

Polymeric hydrogels are promising polymeric functional materials that have been widely used in the biomedical field as an emerging carrier of various therapeutic agents. Polymeric hydrogels as a carrier of therapeutics can leverage therapeutically beneficial outcomes of drug delivery than systemic chemotherapy and can provide spatial and temporal control over the release of various therapeutic agents. Polymeric hydrogels are cross-linked three-dimensional networks constructed by hydrophilic polymers and they are capable of absorbing and re-taining a large amount of water. Polymeric hydrogels share many physiochemical features with natural tissues due to their water abundance, biomimetic microstructure, and intrinsic flexibility. Polymeric hydrogels have excellent biocompatibility, biodegradability, and lower toxicity. Polymeric hydrogels enhance the convenience and efficiency of drug delivery by assisting in situ gelation and controlling drug release by changing their volume and other properties when it encounters some stimuli (e.g., heat, pH, light, and ultrasound). This review aims to outline the overview of polymeric hydrogels, properties, types, advantage, disadvantages, characteri-zation, and their application with present status and future perspective used for the delivery of therapeutics in pharmaceutical and biomedical sciences.

The presence of metal ions, in high concentrations, in the effluents results from industrial metal coating is a well-known fact. Most of time, such metal ions, once they reach the environment, contribute significantly to its degradation. Therefore, it is essential that before such effluents are discharged into the environment, the concentration of metal ions is reduced (as much as possible), to minimize the negative impact on the quality of ecosystems. Among all methods that can be used to reduce the concentration of metal ions, sorption is one of the most viable options, due to its high efficiency and low cost. Moreover, due to the fact that many of the industrial wastes have sorbent properties, this method is in accordance with the principles of circular economy. Based on these considerations, in this study, mustard waste biomass (resulting after oil extraction) was functionalized with an industrial polymeric thiocarbamate (METALSORB), and used as an sorbent to removal Cu(II), Zn(II) and Co(II) ions from aqueous media. The best conditions for the functionalization of mustard waste biomass were found to be: mixing ratio biomass : METASORB = 1g : 1.0 mL and temperature of 30 C. The experimental sorption capacities of functionalized sorbent (MET-MWB) were 0.42 mmol/g for Cu(II), 0.29 mmol/g for Zn(II) and 0.47 mmol/g for Co(II), and were obtained in the following conditions: pH of 5.0, 5.0 g sorbent/L and temperature of 21 C. Modeling of isotherms and kinetic curves, but also the analysis of the results obtained from desorption processes, demonstrates the usefulness of this sorbent in the treatment of effluents contaminated with metal ions. In addition, tests on real wastewater samples highlight the potential of MET-MWB for large-scale applications.

Composite biomaterials that combine osteoconductive and osteoinductive properties are a promising approach for bone tissue engineering (BTE) since it allows osteogenesis stimulation while mimicking the extracellular matrix (ECM) morphology. In this context, the aim of the present research work was to produce polyvinylpyrrolidone (PVP) nanofibers containing mesoporous bioactive glass (MBG) 80S15 nanoparticles. These composite materials were produced by electrospinning technique. The design of experiments (DOE) was used to estimate the optimal electrospinning parameters to reduce average fiber diameter. The polymeric matrices were thermally crosslinked under different conditions, and the fiber’s morphology was studied using scanning electron microscopy (SEM). Evaluation of the mechanical properties of nanofibrous mats revealed a dependence on thermal crosslinking parameters and on the presence of MBG 80S15 particles inside the polymeric fibers. Degradation tests indicated that the presence of MBG led to a faster degradation of nanofibrous mats. On the other hand, MBG presence also leads to higher swelling capacity. The assessment of in vitro bioactivity in simulated body fluid (SBF) was performed in MBG pellets and PVP/MBG (1:1) composites to assess whether the bioactive properties of MBG 80S15 were kept when it was incorporated into PVP nanofibers. FTIR and XRD analysis along with SEM–EDS results indicated that a hydroxy-carbonate apatite (HCA) layer was formed on the surface of MBG pellets and nanofibrous webs after soaking in SBF over different time periods. In general, the materials revealed no cytotoxic effects on Saos-2 cell line. The overall results for the produced materials show the potential of the composites to be used in BTE.

The thermal lubrication of an entangled polymeric liquid in wall-driven shear flows between parallel plates is investigated by using a multiscale hybrid method coupling molecular dynamics and the hydrodynamics (i.e., the synchronized molecular dynamics method). The temperature of the polymeric liquid rapidly increases due to viscous heating once the drive force exceeds a certain threshold value. The rheological properties of the polymeric liquid drastically change at around the critical drive force. In the weak viscous-heating regime, the conformation of polymer chains is dominated by the local shear flow so that the anisotropy of the bond orientation tensor grows as the drive force increases. However, in the large viscous-heating regime, the conformation dynamics is dominated by the thermal agitation of polymer chains so that the bond orientation tensor recovers more uniform and random structures as the drive force increases, even though the local shear flows are further enhanced. Remarkably, these counter-intuitive transitional behaviors give an interesting re-entrant transition in the stress--optical relation, where a linear formalism in the stress--optical relation approximately holds even though each of the macroscopic quantities behaves nonlinearly. The robustness of the linear stress--optical relation is also confirmed in the spatiotemporal evolution at the hydrodynamic level.

Now-a-days, the thrust area of materials’ research is to develop multifunctional materials, which have multiple properties in a single functional material. We are interested to develop multifunctional polysilanes having special functional properties such as optical activity and photoluminescence (PL) properties. In this investigation, poly(methyl phenyl silane) (PMPS) was integrated with a chiral unit and a photoactive unit by in situ photopolymerization of (R)-N-(1-phenyl ethyl) methacrylamide (R-NPEMAM) and disperse red 1 methacrylate (DR1MA) monomer in the presence of PMPS. PMPS acted as a macrophotoinitiator and by UV exposure it produced macroradicals which initiated polymerization of chiral and photoactive monomers. Thus a block copolymer of PMPS-b-(R-NPEMAM-ran-DR1MA) was synthesized.The synthesized multifunctional organic inorganic hybrid polymer samples were characterized by FTIR and NMR spectroscopy. The molecular weights of the samples were measured by GPC analysis. The optical, chiroptical and photoluminescence properties were studied. The narrow band at about 1638 cm^-1 is due to C=O stretching vibration of -CONH- of the chiral unit. A wide absorption peaks at 3444 cm^-1 is the characteristic of NH trans stretching vibration of secondary amide group. The asymmetric stretching of NO₂ group appeared at 1481 cm^-1 and the characteristic peak at 1427 cm^-1 was observed due to azo (-N=N-) group stretching of DR1MA unit. The Si-Si band of PMPS appeared at about 462 cm^-1 in FTIR spectra. The optical absorbance observed at 272 nm is due to π-π* transition of aromatic ring and at 330 nm corresponds to σ-σ* transition of Si-Si bond. The other electronic absorption observed in the visible region at 475 nm corresponds to the combined contribution of n-π* and π-π* transition of DR1MA unit. The photoluminescence properties of such polymers were studied for the variation of concentration of the polymer solution and variation with excitation energy such as 275 nm, 325 nm and 475 nm in THF solvent. Such synthesized multifunctional photoactive organic-inorganic polymers having unusual optical, chiroptical and photoluminescence property may find novel optoelectronic (friend foe identification and secretive code identification) applications.

Amine containing polymers are extensively studied as special carriers for short-chain RNA (13–25 nucleotides) which are applied as gene silencing agent in gene therapy of various diseases including cancer. Elaboration of the oligonucleotide carriers requires knowledge about peculiarities of oligonucleotide - polymeric amine interaction. Critical length of the interacting chains is the important parameter which allows to design sophisticated constructions containing oligonucleotide binding segments, solubilizing, protective and aiming parts. We studied interaction of (TCAG)n, n=1-6 DNA oligonucleotides with polyethylenimine and poly(N-(3-((3-(dimethyl­amino)propyl)(methyl)amino)propyl)-N-methylacrylamide). Critical length for oligonucleotides in interaction with polymeric amines is 8-12 units and complexation at these length can be accompanied by "all-or-nothing" effects. New dimethylacrylamide based polymers with grafted polyamine chains were obtained and studied in complexation with DNA and RNA oligonucleotides. The most effective interaction and transfection activity into A549 cancer cells was found for a sample with average number of nitrogens in polyamine chain equal to 27, i.e. for a sample in which all grafted chains are longer the critical length for polymeric amine - oligonucleotide complexation.

Macrophages are well known for the involvement in the biocompatibility, as well as biodistribution, of nano(bio)materials. Although there are a number of rodent cell lines, they may not fully recapitulate primary cell responses; particularly for those of human cells. Isolation of tissue resident macrophages, from humans, is difficult and may result in insufficient cells with which to determine the possible interaction with nano(bio)materials. Isolation of primary human monocytes, and differentiation to monocyte-derived macrophages, may provide a useful tool with which to study, further, these interactions. To that end, we developed a standard operating procedure for this differentiation, as part of the REFINE project, and used it to measure the secretion of bioactive molecules from M1 and M2 differentiated monocytes in response to model nano(bio)materials, following an initial assessment of pyrogenic contamination which may confound, potential, observations. The SOP was deployed in two partner institutions with, broadly, similar results. The work presented here shows the utility of this assay but, highlights the relevance of donor variability in responses to nano(bio)materials. Whilst donor variability can provide some, logistical, challenges to application of such assays, this variability is much closer to the heterogeneous cells that are present in vivo, compared to homogeneous, non-human, cell lines.

Currently, the most promising work seems to be aimed not so much at the development of new drugs, but rather at creating ways of targeted delivery of existing drugs. In this paper, we show that polymeric micelles based on chitosan, heparin grafted with lipoic and oleic acids residues demonstrate the potential for doxorubicin delivery to tumors due to pH-, glutathione-sensitivity. Smart delivery systems use the Aikido principle, i.e. they target tumor cells according to their features. Natural polysaccharides (heparin and chitosan) provide the pH sensitivity of micelles: the release of doxorubicin (Dox) is enhanced in a slightly acidic environment (model tumor microenvironment). Fatty acid residues are necessary for the formation of micelles and solubilization of cytostatics in a hydrophobic core. Lipoic acid residues formed a labile S-S cross-linking between polymer chains (the first method), and also covalently attached doxorubicin molecules through glutathione-sensitive S-S bridges (the second option) – determine Redox sensitivity of micelles to tumors. The characterization of polymeric micelles and prodrugs (Dox-polymer) was carried out using FTIR spectroscopy. The release of doxorubicin from micelles occurs slowly (20% / 6h) in an environment with a pH of 7.4 and the absence of glutathione, while in a slightly acidic environment and in the presence of 10 mM glutathione, the rate increases up 6 times, with an increase in the effective concentration up to 5 times after 7 h. The permeability of free doxorubicin, micellar formulations (covalent S-S crosslinked and not) into Raji, K562, A875 cancer cells was studied using confocal laser scanning microscopy (CLSM), demonstrated an increase in the permeability of micellar formulations based on Dox. Thus, we have presented micellar formulations of doxorubicin for targeted delivery to tumor, what is important in the aspects of reducing non-target toxicity, increasing the selectivity of cytostatics against tumors and overcome multidrug resistance.

An extensive review of literature simulations of polymer melts is given, considering results that test aspects of the Rouse model in the melt. We focus on the mean-square amplitudes < (X_p(0))^{2} > and time correlation functions < X_p(0) X_p(t) > of the Rouse modes $X_p(t)$. Contrary to the Rouse model: (i) Mean-square Rouse mode amplitudes < (X_p(0))^2> do not scale as sin^{-2}(p \pi/2N), N being the number of beads in the polymer. For small p (say, p <= 3) < (X_p(0))^2> scales with p as p^{-2}$; for larger p it scales as p^{-3}. (ii) Rouse mode time correlation functions < X_p(t) X_p(0) > do not decay with time as exponentials; they instead decay as stretched exponentials exp(-a t^b)$. b depends on p, typically with a minimum near N/2 or N/4. (iii) Polymer bead displacements are not described by independent Gaussian random processes. (iv) For p not equal to q, < X_p(t) X_{q}(0) > is sometimes non-zero. (v) The response of a polymer coil to a shear flow is a rotation, not the affine deformation predicted by Rouse. Simulations thus conclusively demonstrate that the Rouse model is invalid in polymer melts. We also briefly consider the Kirkwood-Riseman polymer model.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

Environmental deterioration factors are constantly increasing, causing unwanted aesthetic changes to stone artworks due to exposure to various physical and chemical deterioration factors. Inorganic nanoparticle-filled polymer composites have extended their multiple functionalities to various applications, including cultural heritage conservation. Therefore, this study has examined the effects of clay, SiO2, Ca(OH)2 and CaCO3 nanomaterials in the enhancement of the physicomechanical properties of limestone monuments, the aim of the present work being to evaluate comparatively the effectiveness of nanoparticles as consolidation and protection material for limestone artworks. The nanoparticles were added to an acrylic-based copolymer (polyethylmethacrylate (EMA)/methylacrylate (MA) (70/30), in order to improve its physiochemical and mechanical properties, and produced a significant improvement in the ability of the polymers to consolidate and protect the stone. The synthesis process of nanoparticles/polymer nanocomposite has been prepared by an in situ emulsion polymerization system. The nanocomposites contained poly (EMA/MA) with a solid content of 3% [poly (EMA/MA)] in the absence and presence of 5% nanoparticles (0.15 g nanoparticles). Samples were subjected to artificial aging by relative humidity/temperature and acid/salt crystallization weathering to show the optimum conditions of durability and the effectiveness of the nano-mixture in improving the physical and mechanical properties of the stone material. To ensure that the treatment had no negative effects on the physical characteristics of the limestone, the properties of the treated limestone samples were evaluated comparatively before and after artificial aging by the conduct of microstructural (phase morphology studied by means of scanning electron microscopy) and aesthetic (colour and lightness measured by spectrophotometry) analyses. Also used were measurement of static contact angle of water droplets on the surface of the samples, total immersion water absorption, compressive strength, and abrasion resistance test. Results demonstrated that the addition of nanoparticles to an acrylic-based polymer enhanced its capability to consolidate and protect the limestone samples.

This paper explores the multifaceted impact of biofilms, bacterial communities enveloped in extracellular polymeric substance (EPS). Biofilms play a dual role, acting as environmental champions and health threats. They interact with heavy metals, either causing pollution or aiding environmental remediation. Beneficial biofilms generate electricity and repair concrete cracks, offering sustainable solutions. Conversely, they contribute to infections, posing health risks. The study emphasizes the need for in-depth research, utilizing bibliographic methods to analyze global biofilm research. By identifying keywords, core countries, and pivotal organizations, the paper informs future investigations, offering insights into biofilm research evolution and practical applications.

Biofilm serves as the residence for bacteria, wherein bacteria attach to surfaces and produce extracellular polymeric substances, including proteins, polysaccharides, and extracellular DNA. In recent years, biofilm reactors have gained increasing significance, playing a crucial role, for instance, in immobilizing heavy metals from waterways. This paper employs a bibliographic study to analyze the most important keywords and organizations in the field of biofilm reactors, identifying recent significant papers. Additionally, the paper discusses the opportunities for the future development of biofilm reactors. Through this study, a better understanding of key factors in biofilm reactor research is achieved, providing valuable guidance for future studies and applications in this field.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

Micellar Casein Concentrate (MCC) is manufactured from microfiltration (MF) of skim milk utilizing ceramic or polymeric membrane filtration. While ceramic filtration has higher efficiency, use of polymeric is cost effective and the process is familiar to several US dairy processors. The aim of the present study was to develop an optimized membrane filtration process to produce MCC using spiral wound polymeric membrane filtration (SW MF) system by systematic selection of transmembrane pressure (TMP) and level of diafiltration (DF). Using skim milk as feed material, preliminary lab-scale MF experiments were conducted using 0.5 µm polyvinylidene fluoride (PVDF) membrane. Three TMP (34.5, 62.1, and 103.4 kPa) and three levels of DF (70, 100, and 150%) along with a process without DF as control were used in the study. Effect of TMP and effectiveness of DF on flux rates, SP removal, casein to total protein (CN/TKN) ratio, casein to true protein (CN/TP) ratio, rejection of casein (rej CN) and SP (rej SP) were evaluated. At all TMP values used in the study, the overall flux (O Flux) increased with the level of DF. Highest O Flux of 30.77 liter per meter square per hour (LMH) was obtained with 34.5 kPa pressure and 150% DF. The impact of DF was more pronounced at lower pressures than at the higher pressures used in the study. With controlled DF, instantaneous flux was maintained within 80% of initial flux for the entire process run. For all the experiments, casein has a rejection of 0.97 to 1.0, while serum protein has the lowest rejection of 0.10 at 34.5 kPa pressure and 150% DF level. Use of 34.5 kPa and DF level of 150 % contributed to 81.45% SP removal, and casein to true protein ratio of 0.96. SP removal data from the lab-scale experiments were fitted into a mathematical model using DF and square of TMP as factors. The model predicts SP removal within 90-95% of actual SP removal got from the pilot plant experiments.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

The mechanical properties of faecal sludge (FS) influence its moisture retention characteristics to a greater extent, besides other properties. A comprehensive fundamental characterization of the mechanical properties is scarce in literature. This research focused on bulk and true densities, porosity, particle size distribution and zeta-potential, extracellular polymeric substances, rheology and dilatancy, microstructure analysis and compactibility, in the context of using the FS as a substitute for soil in land reclamation and bioremediation processes. FS from different on-site sanitation systems were collected from around Durban, South Africa. The porosity of the FS varied between 42% to 63%, with the zeta-potential in negative, below 10 mV. Over 95% of the particles were &lt;1000 µm. The TB-EPS influenced the stability of the sludge, highest being in the septic tank with greywater sample. More proteins than carbohydrates also ascertained the anaerobic nature of the sludge. The results of the textural properties using penetrometer showed similar behaviour as that reported for sewage sludges. The dynamic oscillatory measurements exhibited a firm gel-like behaviour with a linear viscoelastic behaviour of the sludges due to the change in EPS because of anaerobicity. The high TS samples exhibited the role of moisture as a lubricating agent on the motion of solid particles, leading to dilatancy with reduced moisture, where the yield stress was no longer associated with the viscous forces but with the frictional contacts of solid-solid particle interactions. The filtration-compression cell test showed good compactibility, but presence of unbound moisture even at high pressure of 300 kPa.

This paper explores the intricate world of microbial life, focusing on biofilm as a dynamic consortium of bacteria forming complex networks within a self-produced matrix of extracellular polymeric substances (EPS). Analogous to a bacterial house, these structures provide both shelter and support, playing a pivotal role in the microbial realm with dual effects on human and environmental contexts. Biofilm's significance extends beyond its microcosmic architecture, positively contributing to heavy metal removal, electricity generation through microbial fuel cells, and structural remediation, while also posing threats with detrimental formations implicated in conditions from lung to urinary tract infections. Control of biofilm becomes imperative to unlock its positive attributes and mitigate potential negatives, serving as a cornerstone for environmental remediation, sustainable energy, and infrastructure maintenance. Employing a comprehensive bibliographic approach, this study identifies keywords, countries, and organizations influencing biofilm research, proposing innovative avenues like machine learning for future exploration. The aim is not only to contribute to existing knowledge but to pioneer cutting-edge strategies for biofilm optimization and challenge mitigation, shaping its trajectory towards sustainable applications across diverse fields.

New advances of nano-enabled weed management: using poly(epsilon-caprolactone)-based nanoherbicides. A review

Ocular drug delivery is one of the most challenging administration routes due to the very low drug bioavailability. In this work, we produce and characterize mucoadhesive mixed polymeric micelles (PMs) made of chitosan and poly(vinyl alcohol) backbones graft-hydrophobized with short poly(methyl methacrylate) blocks and use them to encapsulate cannabidiol (CBD), an anti-inflammatory cannabinoid. CBD-loaded mixed PMs are physically stabilized by ionotropic crosslinking of the CS domains with sodium tripolyphoshate and spray-drying. These mixed PMs display CBD loading capacity of 20% w/w and sizes of 100-200 nm, and spherical morphology (cryogenic-transmission electron microscopy). The good compatibility of the unloaded and CBD-loaded PMs is assessed in a human corneal epithelial cell line. Then, we confirm the permeability of CBD-free PMs and nanoencapsulated CBD in cornea cell monolayers under liquid-liquid and air-liquid conditions. Overall, our results highlight the potential of these polymeric nanocarriers for ocular drug delivery.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Concrete is the most utilized construction material worldwide. In the marine environment, it is subject to chemical degradation through reactions with chloride (the most important ion), sulfate and magnesium ions in seawater and to biodeterioration resulting from biological (initially microbiological) activities, principally acid production. These two types of corrosion are reviewed and the failure of attempts to predict the degree of deterioration resulting from each is noted. Chemical (abiotic) corrosion is greatest in the splash zone of coastal constructions, while phenomenological evidence suggests that biodeterioration is greatest in tidal zones. There have been no comparative experiments to determine the rates and types of microbial biofilm formation in these zones. Both chemical and microbiological concrete deterioration are complex and have not been successfully modeled. The interaction between abiotic corrosion and biofilm formation is considered. EPS can maintain surface hydration, potentially reducing abiotic corrosion. The early marine biofilm contains relatively specific bacterial colonizers, including cyanobacteria and proteobacteria; these change over time, producing a generic concrete biofilm, but adhesion of microorganisms to concrete in the oceans is little investigated. The colonization of artificial reefs is briefly discussed. Concrete appears to be a relatively prescriptive substrate, with modifications necessary to increase colonization for the required goal of increasing biological diversity.

Cotton cationization with low molecular-weight/polymeric cationic modifiers allows the effective dyeing of fabrics with reactive dyes under salt-free and more environmentally-friendly conditions. The current work focuses on the spectroscopic study of the intermolecular interactions, which dictate the physicochemical process associated with dyeing. Water-soluble copolymers of vinyl benzyl chloride and vinyl benzyl triethylammonium chloride (VBCTEAM) have been used as cellulose cationic modifiers. Dye uptake was assessed using Remazol Brilliant Blue and Novacron Ruby dyes. The study involves ATR-FTIR, UV-Vis, fluorescence and XPS spectroscopy. The results of binary polymer-rich dye-polymer aqueous solutions or dye-polymer precipitates at stoichiometric charge-ratio revealed that the sulfonate/sulfate anions of the dyes interact with the cationic VBCTEAM units of the polymer via electrostatic interactions. Moreover, the comparative study of unmodified/modified dyed cotton indicates that the dye reactive sites remain unaffected for cationized cotton, suggesting that electrostatic interactions are the main driving force for the high dyeing performance observed.

Cells take decisions on their responses depending on the stimuli received by the surrounding extracellular environment, that provides the essential cues at the micro and the nano-lengthscales required for adhesion, orientation, proliferation and differentiation. In this study, discontinuous microcones on silicon (Si) and continuous microgrooves on polyethylene terephthalate (PET) substrates were fabricated via ultrashort-pulsed laser irradiation at various fluences, resulting in microstructures with different roughness and geometrical characteristics. The topographical models attained were specifically developed to imitate the guidance and alignment of Schwann cells for oriented axonal regrowth, towards nerve regeneration. At the same time, positive replicas of the silicon microstructures formed were successfully reproduced, via soft lithography, on the biodegradable polymer poly(lactide-co-glycolide) (PLGA). The anisotropic continuous (PET) and discontinuous (PLGA replicas) microstructured polymeric substrates were assessed in terms of their influence on the Schwann cells responses. It is shown that the developed micropatterned substrates enable control over the cellular adhesion, proliferation and orientation and are thus useful to engineer cell alignment in vitro. This property could be potentially useful in the fields of neural tissue engineering and for dynamic microenvironment systems that simulate in vivo conditions.

This study explores the pivotal biofilm life cycle, essential for comprehending intricate processes in biofilm formation and dispersal. With profound implications for medicine, environmental science, and industrial applications, the life cycle involves initial attachment, irreversible attachment, maturation, and dispersion. Employing bibliographic analysis, the paper unravels critical aspects, unveiling key keywords, prominent research countries/regions, and significant research organizations. This comprehensive approach provides insights into the current biofilm research landscape, identifying gaps for future exploration. Biofilm's influence extends to medical conditions, environmental ecosystems, and industrial challenges, accentuating the urgency of understanding its life cycle. The study also delves into global research distribution and influential organizations, guiding collaborative efforts. As a forward-looking initiative, it proposes future research opportunities, aiming to steer advancements and address challenges in biofilm science. Ultimately, this analysis contributes to the ongoing progress of biofilm research, fostering interdisciplinary collaboration and inspiring future initiatives.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

Valorization of excess sludge through the recovery of high-value products, such as biopolymers, could be a crucial step to implement circular economy principles in wastewater treatment plant (WWTP). In this frame, the present study was aimed at evaluating the simultaneous production of polyhydroxyalkanoates (PHA) and extracellular polymeric substances (EPS), obtainable from the treatment of an agro-industrial wastewater. Two biological systems, one implementing aerobic granular sludge (AGS) and the other a conventional activated sludge operating as a sequencing batch reactor (SBR) were operated for 204 and 186 days, respectively. Both the systems involved a three-stage process for mixed microbial culture enrichment and biopolymers accumulation. The maximum biopolymers accumulation capacity was close to 0.60 mg gVSS^-1 in the AGS when the enrichment reactor was operated at 3 kgCODm^-3d^-1, whereas in the SBR it was slightly more than half (0.35 mg gVSS^-1). Biopolymers extracted from the AGS were mainly constituted by EPS (>70%), which percentage increased with the organic loading rate applied in the enrichment reactor up to 95%. In contrast, SBR enabled to obtain a higher PHA production (50% of the biopolymers). Results suggested that organic carbon was mainly channeled toward metabolic pathways for extracellular storing in AGS, likely as a consequence of metabolic stressors (e.g., hydraulic selection pressure, shear forces) applied for promoting aerobic granulation.

Polyesters based advanced thin films have versatile industrial applications, especially in the filed of textiles, packaging and electronics. Recent advances in polymer science and engineering resulted in development of advanced amorphous and semi-crystalline polyesters with exceptional performance compared to conventional polymeric films. Among these, 1,4-cycloheanedimethanol (CHDM) and cyclic monomer-based polyesters have gained considerable attention attention for their exceptional characteristics and potential applications in smart films. This review article provides a comprehensive overview of the recent advances in the synthesis, characterization, and applications of CHDM and cyclic monomer based advanced polymers for smart film applications. It discussed the structure-property relationship of these innovative polyesters and highlights their unique characteristics including thermal, mechanical, and barrier characteristics. Furthermore, this article also emphases the solution, melt, and solid state polymerization of the polymers. Special emphasis is placed on the influence of the addition of 2nd diol or 2nd diacid on the performance characteristics of synthesized polyesters/copolyesters to explore their versatile industrial applications. Additionally, the impact of stereochemistry of the monomers is also explored to optimized the characterization of polyester, suitable for the industrial applications. Furthermore, this article explores the potential of these advanced polyesters to be considered as a potential materials for smart film applications, especially in the filed of flexible electronics. Finally, the article examines the challenges and future recommendations for the development CHDM and cyclic monomer-based polyesters for smart film applications. It discusses potential avenues for further research, including in-depth studies for the synthesis and characterization of polyesters, development of sustainable and biodegradable alternatives cyclic monomers, alternative green approaches for the synthesis of polymers etc. This review article provides a valuable insights for the researcher from academia and industry working in the field of polymer science and materials engineering.

Algal-bacterial granular sludge, a new biological technology, has been widely recognized due to its highly effective pollutant treatment and energy efficiency. This study investigated the effects of environmental concentrations of Cr(VI) (0.5-2.5 mg/L) on the performance of algal-bacterial gran-ular sludge and self-defensive responses after 90 days of cultivation. The results showed that Cr(VI) affected chemical oxygen demand (COD), ammonia-N and phosphate removal with different trends being apparent. A linear decline in COD removal was observed, whereas an initial de-creasing and then increasing ammonia-N and phosphate removal took place. Algal-bacterial granular sludge effectively removed Cr(VI) from wastewater through biological adsorption and reduction, showing the potential to treat Cr(VI)-contaminated wastewater. Cr(VI) affected the community abundance of the algal-bacterial granular sludge, in which Chlorophyceae and cya-nobacteria were vulnerable under Cr(VI)-induced stress. To reduce the toxicity of Cr(VI), over-produced EPS-PN and antioxidant enzymes (MDA, SOD and CAT) acted as self-defensive responses to resist oxidative damage. This study showed that algal-bacterial granular sludge can remove 00.5 mg/L of Cr(VI) without performance loss. It is hoped that this study can provide useful information for improved engineering feasibility of algal-bacterial granular sludge.

Intranasal (i.n.) administration became an alternative strategy to bypass the blood-brain barrier and improve drug bioavailability in the brain. The main goal of this work was to preliminarily study the biodistribution of mixed amphiphilic mucoadhesive nanoparticles made of chitosan-g-poly(methyl methacrylate) and poly(vinyl alcohol)-g-poly(methyl methacrylate) and ionotropically crosslinked with sodium tripolyphosphate in the brain after intravenous (i.v.) and i.n. administration to Hsd:ICR mice. After i.v. administration, the highest nanoparticle accumulation was detected in the liver, among other peripheral organs. After i.n. administration of a 10-times smaller nanoparticle dose, the accumulation of the nanoparticles in off-target organs was much lower than after i.v. injection. In particular, the accumulation of the nanoparticles in the liver was 20 times lower than by i.v. When brains were analyzed separately, intravenously administered nanoparticles accumulated mainly in the “top” brain, reaching a maximum after 1h. Conversely, in i.n. administration, nanoparticles were detected in the “bottom” brain and the head (maximum reached after 2 h) owing to their retention in the nasal mucosa and could serve as a reservoir from which the drug is released and transported to the brain over time. Overall results indicate that i.n. nanoparticles reach similar brain bioavailability, though with a 10-fold smaller dose, and accumulate in off-target organs to a more limited extent and only after redistribution through the systemic circulation. At the same time, both administration routes seem to lead to differential accumulation in brain regions and thus, they could be beneficial in the treatment of different medical conditions.

Porphyrinic photosensitizers (PSs) and their nano-sized polymer-based carrier systems are required to exhibit low dark toxicity, avoid side effects, and ensure high in vivo tolerability. Yet, little is known about the intracellular fate of PSs during the dark incubation period and how it is af-fected by nanoparticles. In a systematic study, high resolution magic angle spinning NMR spectroscopy combined with statistical analyses was used to study the metabolic profile of cultured HeLa cells treated with different concentrations of the PS chlorin e4 (Ce4) alone or encapsulated in carrier systems. For the latter, either polyvinylpyrrolidone (PVP) or the micelle forming polyethylene glycol (PEG)-polypropylene glycol triblock copolymer Kolliphor P188 (KP) were used. Diffusion edited spectra indicated Ce4 membrane localization evidenced by Ce4 concentration dependent chemical shift perturbation of the cellular phospholipid choline resonance. The effect was also visible in the presence of KP and PVP, but less pronounced. The appearance of the PEG resonance in the cell spectra pointed towards cell internalization of KP whereas no conclusion could be drawn for PVP that remained NMR-invisible. Multivariate statistical analyses of the cell spectra (PCA, PLS-DA and oPLS) revealed a concentration-dependent metabolic response upon exposure to Ce4 that was attenuated by KP and even more by PVP. Significant Ce4-concentration dependent alterations were mainly found for metabolites involved in the tricarboxylic acid cycle and the phosphatidylcholine metabolism. The data underline an important protective role of the polymeric carriers following cell internalization. Moreover, the current study allowed - to our knowledge for the first time - to trace the intracellular PS localization on an atomic level by NMR methods.

Microbial growth has been of prime importance to the researchers in health and biotechnology industries. It has been known to be closely associated to the secretion of extracellular polymeric substances that help in the formation of colonies. Inter-microbial communication happens within such colonies by means of extracellular electron transfer mediated by the aforementioned polymeric substances. Conventionally, different phases of microbial growth are monitored with the aid of a traditional UV-Visible spectrophotometer by measuring the optical density of the liquid medium at 280 nm. In this paper, we have developed an alternative novel way to sense different growth phases employing electrochemical means i.e. two-terminal cyclic voltammetry. This cyclic voltammetry relies on the extracellular electron transfer mechanism taking place via the polymeric substances secreted by the microorganisms, measured by the temporal area changes in the current-voltage hysteresis curves in the inoculated nutrient broth. This work paves a new way to detect the biological activity in the medium, which can be directly correlated to the population of microorganisms. It would be of immense interest to scientists and researchers working in the field of microbiology as well as in development of biosensors, electrochemical sensors etc. which would be helpful in absence of traditional spectrophotometers.

The advancements in the study of the human sense of touch are fueling the field of haptics. This is paving the way for augmenting the sensory perception during objects palpation in tele-surgery, and reproducing the information through tactile feedback. Here, we present a novel tele-palpation apparatus that enables the user to detect nodules with various distinct stiffness buried in an ad-hoc polymeric phantom. The contact force measured by the platform was encoded using a neuromorphic model and reproduced on the index fingertip of a remote user through a haptic glove embedding a piezoelectric disk. We assessed the effectiveness of this feedback in allowing nodule identification under two experimental conditions of real-time telepresence: In Line of Sight (ILS), where the platform was placed in the visible range of a user; and the more demanding Not In Line of Sight (NILS), with the platform being 50 km apart. We found that the entailed percentage of identification was higher for stiffer inclusions with respect to the softer ones (average of 74% within the duration of the task), in both telepresence conditions evaluated. These promising results call for further exploration of tactile augmentation technology for telepresence in medical interventions.

(1) Predictive assessment of the performance characteristics of metal-polymer (MP) plain bearings at the design stage is necessary and important for engineering practice. They include bearing capacity, linear wear of the bushing, and bearing life. However, no method for their calculation has been developed. (2) The authors have created a generalized analytical method for the mathematical modeling of MP sliding bearings as a classical science-based method of contact mechanics of conformal cylindrical bodies with consideration of polymer bushing wear. (3) Contact problem of the theory of elasticity takes into account the significant difference in the elasticity characteristics of polymeric materials from those of steel: Young's modulus is 60...250 times smaller, Poisson's ratio is 1.27...1.37 times larger. The method has been used to study MP bearings with several common groups of tribopolymers used for bushings: PA, PTFE, PET, and PEEK. The maximum contact pressures and durability of dry friction bearings have been calculated taking into account the load, radial clearance, bushing thickness, elasticity characteristics of tribopolymers, their wear resistance, sliding friction coefficient, and type of tribopolymer materials. (4) The paper establishes quantitative and qualitative regularities of the influence of these factors on the maximum contact pressures and bearing durability.

Polymer-based (nano)composite foams, especially those having a microcellular structure, containing suitable conductive (nano)fillers, have been shown to act as good shielding materials, hence coming as promising to act as shields in electronic devices, limiting/avoiding electromagnetic interference (EMI) pollution. Nevertheless, due to their high (micro)structural complexity, related to their multiphase nature, there is still a lot of unawareness behind the shielding mechanisms acting in these materials, coming as a necessity to study their microstructure-cellular/porous structure-properties relations, especially in terms of their electrical conductivity and EMI shielding efficiency (EMI SE). To target and control the electrical conductivity through a controlled distribution/dispersion of conductive nanofillers, single or combined (nanohybrids), as there is a direct relation between electrical conductivity and EMI SE, as well as the main EMI shielding mechanisms working on the developed microcellular structure of the foams, which are expected to be absorption-dominated or absorption/multiple reflection-based, are two of the main objectives when combining polymer foaming with the addition of conductive nanofillers. The present review work considers the recent developments and trends on polymer-based foams containing conductive nanofillers, especially carbon-based such as carbon nanotubes or graphene-based materials, as well as similar porous structures created using trending technologies such as 3D printing, for EMI shielding applications. It is divided in different sections, starting with the strategy of microcellular foaming to develop polymer-based foams with enhanced EMI shielding characteristics, especially focusing on technologies and methods using supercritical CO2 (sCO2); continuing with the use of polymer foams as templates to synthesize carbon foams with improved EMI shielding performance for high use temperature applications; the recent strategy of combining different functional (nano)fillers to create hybrid nanofillers/nanohybrids to be used at lower amounts as conductive fillers in polymer foams; the control and selective distribution of the nanofillers in terms of favoring the formation of a more effective conductive network and hence promote the enhancement of the EMI SE; the very recent use of computational approaches to tailor the EMI shielding properties of composite foams; and the very trending possibility of creating cellular components with varied porous structures from these materials using 3D printing; to finish, some future perspectives are discussed.

The rapid advancements in gene therapy have opened up new possibilities for the treatment of genetic disorders, including Duchenne muscular dystrophy, Thalassemia, cystic fibrosis, Hemophilia, and Familial hypercholesterolemia. The utilization of the clustered regularly interspaced short palindromic repeats (CRISPR) - CRISPR-associated protein (Cas) system has revolutionized the field of gene therapy by enabling precise targeting of genes. In recent years, CRISPR/Cas9 has demonstrated remarkable efficacy in treating cancer and genetic diseases. However, the susceptibility of nucleic acid drugs to degradation by nucleic acid endonucleases, necessitates the development of functional vectors capable of protecting the nucleic acids from enzymatic degradation, while ensuring safety and effectiveness. This review aims to explore the biomedical potential of non-viral vector-explore CRISPR/Cas9 systems for the treatment of genetic diseases. Furthermore, it provides a comprehensive overview of recent research advances in viral and non-viral vector-based gene therapy for genetic disorders, including insights from preclinical and clinical studies. Additionally, the review analyzes the current limitations of these delivery systems and proposes avenues for the development of novel nano-delivery platforms.

In the recent years, tissue engineering researchers have exploited a variety of biomaterials that can potentially mimic extracellular matrix (ECM) for tissue regeneration. Natural cellulose, mainly obtained from bacterial (BC) and plant-based (PC) sources, can serve as a high potential scaffold material for different regenerative purposes. Natural cellulose has drawn the attention of researchers due to its advantage over synthetic cellulose in terms of availability, cost-effectiveness, perfusablility, biocompatibility, negligible toxicity, mild immune response and due to imitating native tissues. In this article, we will review the recent in vivo and in vitro studies aimed to assess the potentials of natural cellulose for the purpose of soft (skin, heart, veins, nerve, among others) and hard (bone and tooth) tissue engineering.

In the field of construction, materials referred to as sustainable are currently undergoing a process of technological development. This study aims to contribute to the understanding of the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate in their matrix a polyethylene terephthalate-based additive in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity and x-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1, 3, 4, 5, 7 and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation whit other physical and mechanical properties are also explained.

The Amazon region, with its vast biodiversity and rich natural resources, presents a unique opportunity for the development of sustainable polymeric composites reinforced with residues from both the timber and agro-extractive industries. This article explores the potential of these Amazonian residues, such as sawdust, wood shavings, and agro-industrial by-products like açaí seeds and Brazil nut shells, to enhance the mechanical, thermal, and environmental properties of polymer composites. By integrating these natural materials into polymer matrices, significant improvements in composite performance have been achieved, including increased tensile strength, thermal stability, and biodegradability. The study also highlights the environmental and economic benefits of utilizing these residues, promoting waste reduction and supporting a circular economy in the region. Through case studies and detailed analyses, the article demonstrates the feasibility and advantages of incorporating Amazonian residues into composites for a wide range of applications, from construction materials to consumer goods. This approach not only adds value to the by-products of the Amazonian industries but also contributes to the global effort towards sustainable material development.

This paper addresses investigation of guided-wave excitation by angle-beam wedge piezoelectric transducers in multi-layered composite plate structure with orthotropic symmetry of the material. The aim of the present study is to determine the capability of such actuators to provide the controlled generation of an acoustic wave of a desirable type with the necessary wavelength, propagation distance and directivity. The studied CFRP panel is considered as homogenous with effective elastic moduli and anisotropic structural damping, whose parameters were determined experimentally. According to the results of dispersion analysis and taking into account the data of wave attenuation in a highly damping CFRP composite, the two types of propagating waves A0 and S0 were considered theoretically and experimentally in the frequency range 10 - 100 kHz. Using the results of a previous study, the structure of the wedge actuator was reconstructed to develop its finite element (FE) model, and a modal analysis was carried out, which revealed the most intense natural vibration modes and their eigenfrequencies within the used frequency range. Both experimental and numerical studies of the generation, propagation, directivity and attenuation of waves in the orthotropic composite panel under study revealed the influence of the angular orientation of the actuator on the formation of wave patterns and allowed to determine the capabilities of the wave's directivity control.

Silymarin, a mixture of flavonolignan and flavonoid polyphenolic compounds extractable from the milk thistle seed, Silybum marianum, has anti-oxidant, anti-inflammatory, anti-cancer and anti-viral activities potentially useful in the treatment of several liver disorders, such as chronic liver diseases, cirrhosis and hepatocellular carcinoma. Equally promising are the effects of silymarin in protecting the brain from the inflammatory and oxidative stress effects by which metabolic syndrome contributes to neurodegenerative diseases. However, despite clinical trials have proved that silymarin is safe at high doses (>1500 mg/day) in humans, it suffers limiting factors such as low solubility in water (<50 μg/mL), low bioavailability and poor intestinal absorption. To improve its bioavailability and provide a prolonged silymarin release at the site of absorption, the use of nanotechnological strategies appears to be a promising method to potentiate the therapeutic action and promote sustained release of the active herbal extract. The purpose of this study is to review the different nanostructured systems available in literature as delivery strategies to improve the absorption and bioavailability of silymarin.

Helicobacter pylori is a gastric pathogen that infects nearly half of the global population and is recognized as a group 1 carcinogen by the Word Health Organization. The global rise in antibiotic resistance has increased clinical challenges in treating H. pylori infections. Biofilm growth has been proposed to contribute to H. pylori’s chronic colonization of the host stomach, treatment failures, and the eventual development of gastric diseases. Several components of H. pylori have been identified to promote biofilm growth, and several of these may also facilitate antibiotic tolerance, including the extracellular matrix, outer membrane proteins, the coccoid morphology, modulated metabolism, efflux pumps, and virulence factors. Recent developments in therapeutic approaches targeting H. pylori biofilm have shown that synthetic compounds, such as small molecule drugs and plant-derived compounds, are effective at eradicating H. pylori biofilms. These combined topics highlight the necessity for biofilm-based research in H. pylori, to improve current H. pylori targeted therapeutic approaches and alleviate relative public health burden. In this review we discuss recent discoveries that have decoded the life cycle of H. pylori biofilms and current biofilm targeted treatment strategies.

Interferons (IFNs) are cytokines involved in the immune response that act on innate and adaptive immunity. These proteins are natural cell-signaling glycoproteins expressed in response to viral infections, tumors, and biological inducers and constitute the first line of defense of vertebrates against infectious agents. They have been marketed for more than 30 years with considerable impact on the global therapeutic protein market thanks to their diversity in terms of biological activities. They have been used as single agents or with combination treatment regimens, demonstrating promising clinical results, resulting in 22 different formulations approved by regulatory agencies. The 163 clinical trials with currently active IFNs reinforce their importance as therapeutics for human health. However, their application has presented difficulties due to the molecules’ size, sensitivity to degradation, and rapid elimination from the bloodstream. For some years now, work has been underway to obtain new drug delivery systems to provide adequate therapeutic concentrations for these cytokines, decrease their toxicity and prolong their half-life in the circulation. Although different research groups have presented various formulations that encapsulate IFNs, to date, there is no formulation approved for use in humans. The current review exhibits an updated summary of all encapsulation forms presented in the scientific literature for these cytokines IFNα, IFNß, and IFNγ, from the year 1996 to the year 2021, considering parameters such as: encapsulating matrix, route of administration, and encapsulation.

The paper is aimed to develop an improved acoustic-based Structural Health Monitoring (SHM) and Non-Destructive Evaluation (NDE) techniques, which provide the waves directivity emitting by the angle-beam wedge actuators in the thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of the generated acoustic waves - anti-symmetric Lamb waves A0 and shear horizontally polarized SH waves SS0. The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain high defects resolution by generating short waves, their adjustable directivity and maximum propagation length. The finite element model for the transducer was built by using the results of actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of actuator's structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by a preliminary research using the similar approach and methods presented in this article.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The aim of the current study was to develop and evaluate the therapeutic potential of apocynin (APO) loaded pH-sensitive nanoparticles (NPs) based transdermal hydrogel for management of rheumatoid arthritis (RA). Slightly modified nanoprecipitation technique was used for preparation of polymeric nanoparticles. Optimization was done through design expert software. Optimized APO-NPs were loaded into carbopol-934 based hydrogel as final dosage form and further studied for physicochemical properties. Optimized APO-NPs formulation had a minimum particle size 63.44 nm, polydisperibility index 0.161, and zeta potential -15mV with a maximum encapsulation efficiency of 89%. In-vitro and ex-vivo studies of APO-NPs based hydrogel was performed at pH 5.5 (pH of normal skin) and 6.8 (pH of inflammed joint) showed a pH-responsive sustained drug release and increased penetration in comparison to free APO based hydrogel. The stability studies of APO-NPs based hydrogel were done to strengthen the potential use of the prepared formulation through transdermal route. Assessment and therapeutic efficacy of the prepared pH-sensitive nanocarriers system was evaluated in chronic inflammatory RA mice model. Parameters associated with chronic inflammation were investigated including behavioral changes and histopathological, and radiological x-rays images of joints of mice paws. In-vivo study depicts improvement in behavioral parameter, decline in synovial hyperplasia and bone structure restoration. In conclusion, APO loaded pH-sensitive NPs based transdermal is a promising carrier system that can effectively manage RA.

There is a growing body of evidence supporting the significant role of bacterial biofilms in the pathogenesis of various human diseases including cancer. Biofilms are polymicrobial communities enclosed within an extracellular matrix composed of polysaccharides, proteins, extracellular DNA, and lipids. This complex matrix provides protection against antibiotics and host immune responses, enabling the microorganisms to establish persistent infections. Moreover, biofilms induce anti-inflammatory responses and metabolic changes in the host, further facilitating their survival. Many of these changes are comparable to those observed in cancer cells. This review will cover recent research on the role of bacterial biofilms in carcinogenesis, especially in colorectal (CRC) and gastric cancers, emphasizing the shared physical and chemical characteristics of biofilms and cancer. This review will also discuss the interactions between bacteria and the tumor microenvironment, which can facilitate oncogene expression and cancer progression. This information will provide insight into developing new therapies to identify and treat biofilm-associated cancers, such as utilizing bacteria as delivery vectors, using bacteria to upregulate immune function, or more selectively targeting biofilms and cancer for their shared traits.

Chen, et al., compared two modified polyurethane-based wound dressings (PUE and PUESi), both intended for use in chronic wounds, with a negative control (gauze) and a positive control (PolyMem) via a series of preliminary in vitro and rodent model tests. Future studies may find that one or both of these two new dressings are beneficial. However, the results of this first study cannot be relied upon. Although they exhibited in-depth knowledge of manufacturing techniques, the study designers seem far less familiar with the science of wound healing and with PolyMem wound dressings. This helps explain the flaws in the methods that lead to many of their tests not being translatable to real-world settings. In addition, the interpretation of some of the test results is questionable.

The main purpose of this study was to develop a model for predicting the quality of holes drilled in the root part of a spar of helicopter main rotor blades made of the Glass Fiber Reinforced Plastic (GFRP)-Ti multilayer polymer composite. As the main quality criterion, delaminations at the entry and exit of the drill from the hole were taken. In the experimental study a conventional drill and two modified geometry drills: a double-point angle drill and a dagger drill were used. Preliminary experiments showed the best hole quality when using modified drills, which allowed further detailed study only with both modified drills at different drilling speeds and feed rates. Its results in the form of training sets were used to build the Artificial Neural Networks (ANNs) to predict delamination at the entry and exit of drilled holes. The analysis of the fitted response functions, presented as 3D surfaces plots and superimposed contour plots, made it possible to choose the better tool - a double-point angle drill and determine the optimal area for drilling speed and feed rates, confirming that the prediction of the quality and productivity of machining composites based on ANN is an effective tool to search and quantify the quality criteria of such technologies.