This paper proposes a novel micro-grid structure, which can operate fully-autonomously with inherent seamless switching. It can operate independently in both grid-connected and islanded mode as a self-governed entity without relying on the utility grid. An AC/DC/AC converter is employed as the interface between the micro-grid and the utility grid, which enables the two entities to have different voltages in grid-connected mode. Seamless switching between operation modes can be achieved naturally. The micro-grid is regulated to exchange predefined amount of power with the utility grid in grid-connected mode. This will benefit the power dispatching algorithm of the power system. The predefined power is estimated based on power forecasting of local renewable generations and loads with consideration of the Sate of Charge (SOC) of the battery, and is updated and broadcasted every certain period. A small scale AC micro-grid with a rotating generator, battery storage and solar arrays etc. is built for investigation. Matlab/Simulink results are provided to validate the robustness and flexibility of proposed micro-grid and its operation strategy.

Several design methods and principles have been presented so far, in order to guide the design of autonomous operations. Putting the required efforts into learning and using the methods for designing autonomous operations is a daunting task. Experiences so far have shown that the use of methods meant to the help the design process are often ignored. One reason could be that the design guidelines are too complex and contain much information often not relevant for the project at hand, and therefore there is no easy way to distinguish what is important from what is not. This is an issue that needs to be solved with our approach. In this article, the Autonomous Job Analysis (AJA) method is presented. The proposed methodology is created in order to guide the design of autonomous operations in maritime systems by breaking them down in to sub-operations in order to reveal challenges, needs and limitations regarding autonomous behavior. The canvas contains the categories of the AJA method on a single page format -the canvas- and each category is supported with questions to be asked during the design procedure, as well as example answers. We will describe the AJA method and the AJA canvas in detail, and present a use case scenario of an autonomous operation in order to show how they can be applied. The particular use-case is the design of an autonomous operation for the detection, inspection and tracking of a waste water plume.

Integrating advanced air mobility (AAM) into the logistics of high-value electronic commodities can enhance efficiency and promote sustainability. The objective of this study is to optimize the logistics network for high-value electronics by integrating AAM solutions, specifically using heavy-lift cargo drones for middle-mile transport and using the mostly rural and small urban U.S. state of North Dakota as a case study. The analysis utilized geographic information system (GIS) and spatial optimization models to strategically assign underutilized airports as multimodal freight hubs to facilitate the shift from long-haul trucks to middle-mile air transport. Key findings demonstrate that electronics, because of their high value-to-weight ratio, are ideally suited for air transport. Comparative analysis shows that transport by drones can reduce the average cost per ton by up to 60% compared to traditional trucking. Optimization results indicate that a small number of strategically placed logistical hubs can reduce average travel distances by more than 13% for last-mile deliveries. Cost analyses demonstrate the viability of drones for middle-mile transport, especially on lower-volume rural routes, highlighting their efficiency and flexibility. The study emphasizes the importance of utilizing existing infrastructure to optimize the logistics network. By replacing truck traffic with drones, AAM can mitigate road congestion, reduce emissions, and extend infrastructure lifespan. These insights have critical implications for supply chain managers, shippers, urban planners, and policymakers, providing a decision support system and a roadmap for integrating AAM into logistics strategies.

In the realm of autonomous driving tort, a significant disparity exists in the parties' access to autonomous driving data and essential technical information, resulting in challenges in unilateral proof. The traditional burden of proof framework in driving litigation is inadequate for direct application in the autonomous driving sphere. As we approach the era of widespread autonomous driving operations, there is an urgent need to clarify and redefine the allocation of the burden of proof in specific litigations. Utilizing comparative legal analysis and case studies, this paper delves into the disparities in legislative provisions concerning the burden of proof for autonomous driving in Germany and China. China can learn from Germany's legislative precedence in shifting the burden of proof for 'product defect' and 'fault' onto the manufacturer, thereby requiring the infringed party to merely furnish preliminary evidence indicating a 'causal relationship between the defect and the damage.' This approach mitigates the evidentiary burden on the aggrieved party, clarifies litigation procedures, incentivizes manufacturers to enhance technology, reinforces risk management, and ultimately, facilitates the progression of autonomous driving technology.

This article focuses on generating an alternative in order to identify traffic officers during driving. This research employed the latest You Only Look Once (YOLO) model, using a six-phase methodology: data collection, data preparation involving resizing and labeling, implementation of various filters to avoid overfitting, model training, prediction evaluation, and result interpretation. The YOLO model was applied across three iterations using a dataset of 1862 images. To enhance training efficiency and detection speed, the graphics processing unit (GPU) acceleration was utilized, further enhancing the experimental process. The results of this study revealed that the YOLOv8x variant produced the most promising results. This proposed model attained a remarkable F1 score of 0.95, bolstered by a confidence score of 0.631, with the potential for an increase to 0.80 in confidence without significantly compromising the F1-score. These findings are poised to make a substantial contribution to the broader research landscape, particularly in advancing the effectiveness of detection models for traffic officers.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

For autonomous driving, perception is a primary and essential element that fundamentally deals with the insight into the ego vehicle’s environment through sensors. Perception is a challenging task suffering from dynamic objects and continuous environmental changes. The issue gets worse due to interrupting the quality of perception by adverse weather like snow, rain, fog, night light, sand storm, strong daylight, etc. In this work, we have tried to improve camera-based perception accuracy, such as autonomous driving-related object detection in adverse weather. We proposed the improvement of YOLOv8-based object detection in adverse weather through transfer learning using merged data from various harsh weather datasets. Two prosperous open-source datasets (ACDC and DAWN) and their merged dataset were used to detect primary objects on the road in harsh weather. A set of training weights were collected from training on the individual datasets, their merged version, and several subsets of those datasets according to their characteristics. A comparison between the training weights also occurred by evaluating the detection performance on the above-mentioned datasets and their subsets. The evaluation revealed that using custom datasets for training significantly improves the detection performance compared to the YOLOv8 base weights. And using more images through the feature-related data merging technique steadily increases the object detection performance.

Reinforcement Learning (RL) has demonstrated considerable potential in solving challenges across various domains, notably in autonomous driving. Nevertheless, implementing RL in autonomous driving comes with its own set of difficulties, such as the overestimation phenomenon, extensive learning time, and sparse reward problems. Although solutions like Hindsight Experience Replay (HER) have been proposed to alleviate these issues, the direct utilization of RL in autonomous vehicles remains constrained due to the intricate fusion of information and the possibility of system failures during the learning process. In this paper, we present a novel RL-based autonomous driving system technology that combines Obstacle Dependent Gaussian (ODG) RL, Soft Actor-Critic (SAC), and meta-learning algorithms. Our approach addresses key issues in RL, including the overestimation phenomenon and sparse reward problems, by incorporating prior knowledge derived from the ODG algorithm. We evaluated our proposed algorithm on official F1 circuits, using high-fidelity racing simulations with complex dynamics. The results demonstrate exceptional performance, with our method achieving up to 89% faster learning speed compared to existing algorithms in these environments.

In the context of partial autonomy, where autonomous vehicles and humans share control of the vehicle, bringing out-of-the-loop drivers back into the loop is a significant challenge. While warning signal design guidelines are commonly used to provide alerts, few studies have examined each signal in depth with an emphasis on the autonomous environment. This study aims to fill this gap by investigating visual, auditory, and tactile stimuli and modifying their sub-attributes to explore variations related to age, gender, and other individual backgrounds. A driving simulator was utilized to create a realistic driving environment and measure participants' reaction times in takeover request situations. Analysis of the data revealed correlations between age and reaction times for auditory and tactile signals, with interaction effects observed between age and sub-attribute intensity. Additionally, participants exhibited varying reaction time patterns in response to different sub-attribute intensities. By evaluating individual differences in perception based on modality characteristics, often overlooked in prior research, this study serves as a foundational contribution to future research in the field.

This paper presents an analysis of the sensitivity of controlling an autonomous surface object among a group of encountered objects to the inaccuracy of state control process data. For this purpose, a safe and optimal model of the control process was defined. An algorithm for determining the optimal and safe trajectory of an object, based on the multi-object game model, was developed; for comparative analysis, an algorithm for calculating only the optimal trajectory, not taking into account the maneuverability of other objects, was additionally developed. First, simulation-based studies of the algorithms enabled a comparative analysis of a number of different acceptable strategies for optimally shifting the trajectory of maneuvering objects from a single initial direction. Thereafter, the main goal of this paper was implemented: an analysis of the sensitivity characteristics of safe control, assessed with the risk of collision, both on the inaccuracy of navigation data and on the number of possible control strategies. Finally, final conclusions and a plan for further research on the subject of the paper were formulated.

In the context of Shared Autonomous Vehicles, the need to monitor the environment inside the car will be crucial. This article focuses on the application of deep learning algorithms to detect objects, namely lost/forgotten items to inform the passengers, and aggressive items to monitoring if violent actions may arise between passengers. For object detection algorithms was used public datasets (COCO and TAO) to train state-of-the-art algorithms, such as YOLOv5. For violent action detection was used the MoLa InCar dataset to train on state-of-the-art algorithms such as I3D, R(2+1)D, SlowFast, TSN and TSM. At the end an embedded automotive solution was used to demonstrate both methods running in real-time.

Adaptive Cruise Control (ACC) is useful in the most dangerous maneuvers such as braking and acceleration. This study assesses how ACC modifies traffic flows by analysing the differences be-tween manual and autonomous driving in connected and autonomous vehicles (CAVs). Using a platoon of 80 vehicles, tested in pairs on the road, it was possible to define the speed trends during braking and acceleration and the reaction times to the driving maneuvers (PRT, TH, TCC) with a kinematic data detector. The interactions between the CAV and the driver, have been studied in-novatively, i.e through gaze analysis. Situations of potential danger, characterized by the braking of the vehicle that precedes the car with the driver equipped with the eye tracker tool, have been recreated, considering the influence of the driver’s ACC experience. Results statistically confirmed that with the ACC switched on the reaction times are greater than manual driving (2.4/3.8 sec); this can lead to a reduction in road safety, further motivated by the rapid decrease in speed. The interpolation between automated and human data, finally, has allowed the detection of some criticalities of the system that are fundamental in order to reach the second level of automation.

Fog, haze, or smoke are usual atmospheric phenomena that dramatically compromise the overall visibility of any scene, critically affecting features such as illumination, contrast, and contour detection of objects. The decrease in visibility compromises the performance of computer vision algorithms such as pattern recognition and segmentation, some of them very relevant for decision-making for the security or autonomous vehicle industries. Several dehazing methods have been proposed, however, to the best of our knowledge, all proposed metrics compare the defogged image to its ground truth for evaluation of the defogging algorithms, or need to estimate parameters through physical models. This fact hinders progress in the field as obtaining proper ground truth images is costly and time-consuming, and physical parameters greatly depend on the scene conditions. This paper aims to tackle this issue by proposing a contour-based metric for image defogging evaluation that does not need a ground truth image. The proposed metric only requires the original hazy RGB image and the RGB image after the defogging procedure. A comparison of the proposed metric with metrics currently used in the NTIRE 2018 defogging challenge is performed to prove its effectiveness in a general situation, showing comparable results to conventional metrics.

This paper concerns a new methodology for accuracy assessment of global positioning system verified experimentally with LiDAR (Light Detection and Ranging) data alignment at continent scale for autonomous driving safety analysis. Accuracy of GPS (Global Positioning System) positioning of an autonomous driving vehicle within a lane on the road is one of the key safety considerations. Safety is addressed as a geometry of the problem, where the aim is to maintain knowledge that the vehicle (its bounding box) is within its lane. Accuracy of GPS positioning is checked by comparing it with mobile mapping tracks in the recorded high definition source. The aim of the comparison is to see if the GPS positioning remains accurate up to the dimensions of the lane where the vehicle is driving. For this reason, a new methodology is proposed. Methodology is composed of six elements: 1) Mobile mapping system minimal setup, 2) Global positioning data processing, 3) LiDAR data processing, 4) Alignment algorithm, 5) Accuracy assessment confirmation and 6) Autonomous driving safety analysis. The research challenge is to assess positioning accuracy of moving cars taking into account the constraints of the coverage of limited access highways in the United States of America. The available coverage limits the possibility of repeatable measurements and introduces an important challenge being the lack the ground truth data. State-of-the-art methods are not applicable for this particular application, therefore a novel approach is proposed. The method is to align all the available LiDAR car trajectories to confirm the GNSS+INS (Global Navigation Satellite System + Inertial Navigation System) accuracy. For this reason, the use of LiDAR metric measurements for data alignment implemented using SLAM (Simultaneous Localization and Mapping) was investigated, assuring no systematic drift by applying GNSS+INS constraints. SLAM implementation used state-of-the-art observation equations and the Weighted Non-Linear Least Square optimization technique that enables integration of the required constraints. The methodology was verified experimentally using arbitrarily chosen measurement instruments (NovAtel GNSS+INS, LiDAR Velodyne HDL32) mounted onto mobile mapping systems. The accuracy was assessed and confirmed by the alignment of 32785 trajectories with total length of 1,159,956.9~km and of total $186.4*10^{9}$~optimized parameters (six degrees of freedom of poses) that cover the United States region in the 2016--2019 period. It is demonstrated that the alignment improves the trajectories, thus final map is consistent. The proposed methodology extends the existing methods of global positioning system accuracy assessment focusing on realistic environmental and driving conditions. The impact of global positioning system accuracy on autonomous car safety is discussed. It is shown that 99\% of the assessed data satisfies the safety requirements (driving within lanes of 3.6~m) for Mid-Size (width 1.85~m, length 4.87~m) vehicle and 95\% for 6-Wheel Pickup (width 2.03--2.43~m, length 5.32--6.76~m). The conclusion is that this methodology has great potential for global positioning accuracy assessment at global scale for autonomous driving applications. LiDAR data alignment is introduced as a novel approach to GNSS+INS accuracy confirmation. Further research is needed to solve the identified challenges.

Considering the significant advancements in autonomous vehicle technology, research in this field is of interest to researchers. To drive vehicles autonomously, controlling steer angle, gas hatch, and brakes need to be learned. The behavioral cloning method is used to imitate humans’ driving behavior. We created a dataset of driving in different routes and conditions and using the designed model, the output used for controlling the vehicle is obtained. In this paper, the Learning of Self-driving Vehicles Based on Real Driving Behavior Using Deep Neural Network Techniques (LSV-DNN) is proposed. We designed a convolutional network which uses the real driving data obtained through the vehicle’s camera and computer. The response of the driver is during driving is recorded in different situations and by converting the real driver’s driving video to images and transferring the data to an excel file, obstacle detection is carried out with the best accuracy and speed using the Yolo algorithm version 3. This way, the network learns the response of the driver to obstacles in different locations and the network is trained with the Yolo algorithm version 3 and the output of obstacle detection. Then, it outputs the steer angle and amount of brake, gas, and vehicle acceleration. The LSV-DNN is evaluated here via extensive simulations carried out in Python and TensorFlow environment. We evaluated the network error using the loss function. By comparing other methods which were conducted on the simulator’s data, we obtained good performance results for the designed network on the data from KITTI benchmark, the data collected using a private vehicle, and the data we collected.

In the field of autonomous vehicles, lane detection and control plays an important role. In autonomous driving the vehicle has to follow the path to avoid the collision. A deep learning technique is used to detect the curved path in autonomous vehicles. In this paper a customized lane detection algorithm was implemented to detect the curvature of the lane. A ground truth labelling tool box for deep learning is used to detect the curved path in autonomous vehicle. By mapping point to point in each frame 80-90% computing efficiency and accuracy is achieved in detecting path.

Road conditions, often degraded by insufficient maintenance or adverse weather, significantly contribute to accidents, exacerbated by the limited human reaction time to sudden hazards like potholes. Early detection of distant potholes is crucial for timely corrective actions, such as reducing speed or avoiding obstacles, to mitigate vehicle damage and accidents. This paper introduces a novel approach that utilizes perspective transformation to enhance pothole detection at different distances, focusing particularly on distant potholes. Perspective transformation improves the visibility and clarity of potholes by virtually bringing them closer and enlarging their features, which is particularly beneficial given the fixed-size input requirement of object detection networks, typically smaller than the raw image resolutions captured by cameras. Our method automatically identifies the region of interest (ROI)—the road area—and calculates the corner points to generate a perspective transformation matrix. This matrix is applied to all images and corresponding bounding box labels, enhancing the representation of potholes in the dataset. This approach significantly boosts detection performance when used with YOLOv5-small, achieving a 45.7\% improvement in average precision (AP) at IoU thresholds of 0.5 to 0.95 for a single class, and notable improvements of 30.3\%, 78.6\%, and 278\% for near, medium, and far pothole classes, respectively, after categorizing them based on their distance. This work is the first to employ perspective transformation specifically for enhancing the detection of distant potholes.

To date, the development of unmanned technologies using autonomous underwater vehicles (AUV) has become an urgent demand for solving the problem of inspection of industrial sub-sea structures. A key issue here is precise localization of AUVs relative to underwater objects. However, the well-known challenges of recognizing and coordinating underwater objects (impossibility to use GPS, undercurrents, etc.) do not allow high-precision navigation if based solely on a standard suite of AUV navigation tools (sonars, etc.). An alternative is a technology of processing of optical images that, at short distances, can provide higher accuracy of AUV navigation compared to a technology of acoustic measurement processing. In this study, in the context of the problem of subsea production system inspection, we propose a method to recognize underwater objects and provide coordinate reference of AUV to them, based on stereo-image processing. Its distinctive features are the use of a non-standard technique for generating a geometric model of an object from its views (foreshortening) taken from positions of a pre-made overview trajectory, the use of various characteristic geometric elements when recognizing objects, and the original algorithms for comparing visual data of the inspection trajectory with an a priori model of the object.

This paper systematically discusses the application of reinforcement learning in automatic driving system. Reinforcement learning frameworks show significant advantages in optimizing decision making, predictive perception, path planning, and controller design, exceeding the limitations of traditional supervised learning methods. The paper highlights the critical role of components such as scene understanding, positioning, and map making in autonomous driving systems, which provide reliable environmental awareness through deep learning and sensor fusion technologies to support intelligent decision-making in complex urban environments. In addition, the paper discusses innovative approaches to safety reinforcement learning to reduce risk in autonomous driving and ensure that systems adhere strictly to safety constraints while maximizing expected rewards. These findings provide an important theoretical and practical basis for further improving algorithm robustness, managing multi-agent interactions, and integrating ethical considerations in the future.

Technological developments within the maritime sector are resulting in rapid progress that will see the commercial use of autonomous vessels, known as Maritime Autonomous Surface Ships (MASS). Such ships are equipped with a range of advanced technologies, such as IoT devices, artificial intelligence (AI) systems, machine learning (ML) based algorithms and augmented reality (AR) tools. Through such technologies, the autonomous vessels can be remotely controlled from Shore Control Centres (SCC) by using real-time data to optimise their operations, enhance safety and reduce the possibility of human error. Apart from the regulatory aspects, which are under definition by the International Maritime Organisation (IMO), cybersecurity aspects must be considered and properly addressed to prevent such complex systems from being tampered with. In this paper, we propose an approach to secure communication channels between the SCCs and the vessels using SECOM standard and the underlying digital infrastructure in charge of data collection, storage and processing by relying on a set of machine learning (ML) algorithms for anomaly detection. The proposed approach is validated against a real implementation of the SCC deployed at Livorno seaport premises. Finally, the experimental results and the performance evaluation are provided to assess its effectiveness accordingly.

Artificial intelligence (AI) systems of autonomous systems such as drones, robots and self-driving cars may consume up to 50% of total power available onboard, thereby limiting the vehicle’s range of functions and considerably reducing the distance the vehicle can travel on a single charge. Next-generation onboard AI systems need an even higher power since they collect and process even larger amounts of data in real time. This problem cannot be solved using the traditional computing devices since they become more and more power-consuming. In this review article, we discuss the perspectives of development of onboard neuromorphic computers that mimic the operation of a biological brain using nonlinear-dynamical properties of natural physical environments surrounding autonomous vehicles. Previous research also demonstrated that quantum neuromorphic processors (QNPs) can conduct computations with the efficiency of a standard computer while consuming less than 1% of the onboard battery power. Since QNPs is a semi-classical technology, their technical simplicity and low, compared with quantum computers, cost make them ideally suitable for application in autonomous AI system. Providing a perspective view on the future progress in unconventional physical reservoir computing and surveying the outcomes of more than 200 interdisciplinary research works, this article will be of interest to a broad readership, including both students and experts in the fields of physics, engineering, quantum technologies and computing.

Equipping autonomous agents for dynamic interaction and navigation is a significant challenge in intelligent transportation systems. This study aims to address this by implementing a brain-inspired model for decision-making in autonomous vehicles. We employ active inference, a Bayesian approach that models decision-making processes similar to the human brain, focusing on the agent's preferences and the principle of free energy. This approach is combined with imitation learning to enhance the vehicle's ability to adapt to new observations and make human-like decisions. The research involved developing a multi-modal self-awareness architecture for autonomous driving systems and testing this model in driving scenarios, including abnormal observations. The results demonstrated the model's effectiveness in enabling the vehicle to make safe decisions, particularly in unobserved or dynamic environments. The study concludes that the integration of active inference with imitation learning significantly improves the performance of autonomous vehicles, offering a promising direction for future developments in intelligent transportation systems.

Autonomous target recognition (ATR) plays a crucial role in maintaining situational awareness during environmental monitoring. Unmanned aerial vehicles (UAVs) equipped with autonomous target recognition technology can gather and analyze real-time information about targets, including their locations, sizes, and types. However, UAV-captured images in complex real-world environments often display significant variations in perspective and scale due to changes in UAV altitude and distance. Existing methods for autonomous target recognition on UAVs struggle to capture targets from large field-of-view and multi-scale images, resulting in low recognition accuracy and high false-positive rates. This paper introduces two novel Slimmable neural network models, namely SE-YOLOv5s and ST-YOLOv5s, which are based on the YOLOv5s architecture. These models incorporate the Squeeze and Excitation and Swin-Transformer mechanisms to enhance the ability to extract features from large field-of-view and multi-scale images. To evaluate their performance, experiments were conducted on the Visdrone19 aerial dataset. Compared to the state-of-the-art YOLOv5s algorithm, the utilization of SE-YOLOv5s and ST-YOLOv5s for autonomous target recognition on low-altitude drones resulted in improvements in both accuracy and false-positive rates. These proposed methods combine Slimmable neural network design with feature enhancement mechanisms, addressing the challenges posed by complex real-world environments in UAV missions. The advancements in autonomous target recognition on low-altitude drones will significantly contribute to enhancing situational awareness in future environmental monitoring.

Object detection is important in many applications, such as autonomous driving. While 2D images are lack of depth information and are sensitive to environmental conditions, 3D point cloud can provide accurate depth information and a more descriptive environment. However, sparsity is always a challenge in single-frame point cloud object detection. This paper introduces a two-stage proposal-based feature fusion method for object detection using multiple frames. The proposed method, called proposal features fusion (PFF), utilizes a cosine-similarity approach to associate proposals from multiple frames and employs an attention weighted fusion module to merge features from these proposals. It allows for feature fusion specific to individual objects and offers lower computational complexity while achieving higher precision. The experimental results on the nuScenes dataset demonstrate the effectiveness of our approach, achieving a mAP of 46.7%, which is 1.3% higher than the state-of-the-art 3D object detection method.

Autonomous driving vehicles rely on sensors for the robust perception of surroundings. Such vehicles are equipped with multiple perceptive sensors with a high level of redundancy to ensure safety and reliability in any driving condition. However, multi-sensor, such as camera, LiDAR and radar, systems bring up the requirements related to sensor calibration and synchronization, which are the fundamental blocks of any autonomous system. On the other hand, sensor fusion and integration have become important aspects of autonomous driving research and directly determine the efficiency and accuracy of advanced functions such as object detection and path planning. Classical model-based estimation and data-driven models are two mainstream approaches to achieving such integration. Most recent research is shifting to the latter, showing high robustness in real-world applications but requiring large quantities of data to be collected, synchronized, and properly categorized. To generalize the implementation of the multi-sensor perceptive system, we introduce an end-to-end generic sensor dataset collection framework that includes both hardware deploying solutions and sensor fusion algorithms. The framework prototype integrates a diverse set of sensors, such as cameras, LiDAR, and radar. Furthermore, we present a universal toolbox to calibrate and synchronize three types of sensors based on their characteristics. The framework also includes the fusion algorithms, which utilize the merits of three sensors , namely, camera, LiDAR and radar, and fuse their sensory information in a manner that is helpful for object detection and tracking research. The generality of this framework makes it applicable in any robotic or autonomous applications, also suitable for quick and large-scale practical deployment.

For the emerging autonomous swarm technology, from the perspective of systems science and systems engineering, there must be some novel elements and methods to aggregate multiple systems into a group, which distinguish with the general components with specific functions, and we expect to provide the presentation of their existence in the swarm development processes. The inspiration of our methodology origins from the integration of swarm ontology, multi-paradigm modeling, multi-agent system, cyber-physical system, etc. Therefore, we choose the model-driven technology as a framework to acquire an approach of model representation across the multiple levels of abstraction and composition. The autonomous strategic mechanism is defined and formed in parallel with ConOps analysis and systems design, so as to effectively solve the cognitive problem of emergence caused by the nonlinear causation among individual and whole behaviors. This approach highlights to use the MBSE processes and their artifacts to embed the meso mechanism to integrate the operational and the functional, and which means to connect the macro and micro aspects in formalism and so to become a whole with its expected goals, and then to verify and validate within a L-V-C simulation environment.

Autonomous systems and intelligent machines are involved in almost all areas of human activity and they are now more and more present in our everyday life. The reason for this extensive use certainly resides in all the benefits these machines offer to the users. In experimental settings, numerous studies have demonstrated the positive effects that the introduction of autonomous systems have on human decision-making and performance. However, studies have shown in addition that the introduction of these systems can have important negative effects as well. Considering that autonomous systems are now introduced in sensitive domains like the military or medicine, we need more than ever a comprehensive understanding of the effects they cause on human performance and decision-making, and particularly in tasks and contexts with a social or moral dimension. The aim of this narrative review is threefold. First, we will provide an overview of the main effects on a human agent’s decision-making and performance produced by the introduction of autonomous systems. Second, we will review the conditions identified as underlying factors of these effects, and see how current models of human – autonomous systems interaction integrate those conditions. Third, we will conclude this review by highlighting new directions for future investigations.

Object segmentation is still considered a challenging problem in autonomous driving, particularly in consideration of real world conditions. Following this line of research, this paper approaches the problem of object segmentation using LiDAR-camera fusion and semi-supervised learning implemented in a fully-convolutional neural network. Our method is tested on real-world data acquired using our custom vehicle iseAuto shuttle. The data include all-weather scenarios, featuring night and rainy weather. In this work, it is shown that LiDAR-camera fusion with only a few annotated scenarios and semi-supervised learning, it is possible to achieve robust performance on real-world data in a multi-class object segmentation problem. The performance of our algorithm is measured in terms of intersection over union, precision, recall and area-under-the-curve average precision. Our network achieves 82% IoU in vehicle detection in day fair scenarios and 64% IoU in vehicle segmentation in night rain scenarios.

To validate the accuracy and reliability of onboard sensors for object detection and localization in driver assistance, as well as autonomous driving applications under realistic conditions (indoors and outdoors), a novel tracking system is presented. This tracking system is developed to determine the position and orientation of a slow-moving vehicle (e.g. car during parking maneuvers), independent of the onboard sensors, during test maneuvers within a reference environment. One requirement is a 6 degree of freedom (DoF) pose with a position uncertainty below 5 mm (3σ), an orientation uncertainty below 0.3° (3σ) at a frequency higher than 20 Hz, and a latency smaller than 500 ms. To compare the results from the reference system with the vehicle’s onboard system, a synchronization via Precision Time Protocol (PTP) and a system interoperability to Robot Operating System (ROS) is implemented. The developed system combines motion capture cameras mounted in a 360° panorama view set-up on the vehicle with robotic total stations. A point cloud of the test site serves as a digital twin of the environment, in which the movement of the vehicle is simulated. Results have shown that the fused measurements of these sensors complement each other, so that the accuracy requirements for the 6 DoF pose can be met, while allowing a flexible installation in different environments.

Autonomous weapons systems (AWS), sometimes referred to as “killer robots”, are receiving evermore attention, both in public discourse as well as by scholars and policymakers. Much of this interest is connected with emerging ethical and legal problems linked to increasing autonomy in weapons systems, but there is a general underappreciation for the ways in which existing law might impact on these new technologies. In this paper, we argue that as AWS become more sophisticated and increasingly more capable than flesh-and-blood soldiers, it will increasingly be the case that such soldiers are “in the power” of those AWS which fight against them. This implies that such soldiers ought to be considered hors de combat, and not targeted. In arguing for this point, we draw out a broader conclusion regarding hors de combat status, namely that it must be viewed contextually, with close reference to the capabilities of combatants on both sides of any discreet engagement. Given this point, and the fact that AWS may come in many shapes and sizes, and can be made for many different missions, we argue that each particular AWS will likely need its own standard for when enemy soldiers are deemed hors de combat. We conclude by examining how these nuanced views of hors de combat status might impact on meaningful human control of AWS.

Complexity is a crucial metric for evaluating urban intersection scenarios. However, existing complexity evaluations are often derived indirectly from the driving risk of autonomous vehicles, leading to subjective and incomplete evaluations. Therefore, this study undertakes a comprehensive evaluation of intersection scenarios from a systems perspective by quantifying the number of vehicles and the characteristics of vehicle interactions within the intersection.Specifically, we propose an objective framework for assessing complexity. In this framework, the number of vehicles serves as the foundation for assessment, while three interaction characteristics—interaction density, interaction disorder, and interaction risk—are modeled as scaling factors of complexity. In particular, by combining logistic and hyperbolic tangent functions, we accurately capture the nonlinear effects of vehicle numbers and interaction characteristics on complexity.The experimental results demonstrate that the evaluation outcomes of the proposed method are highly correlated with the risk and efficiency performance of autonomous vehicles at intersections, thereby validating the method. Additionally, this method is utilized to guide the generation of highly complex urban intersection scenarios, achieving double the generation efficiency compared to the random sampling method.

This paper examines the control challenges faced by underactuated Autonomous Underwater Vehicles (AUVs) under ocean current disturbances. It proposes a Backstepping Integral Sliding Mode Control (BISMC) strategy to enhance their adaptability and robustness. The BISMC strategy integrates the system decomposition capability of the Backstepping Control method with the rapid response and robustness advantages of the Sliding Mode Control method, enabling the design of a heading controller and a double closed-loop depth controller. By introducing an integral component, the strategy eliminates steady-state errors caused by ocean currents, accelerating system convergence and improving accuracy. Furthermore, a saturation function is employed to mitigate output chattering issues. Simulation results demonstrate that the BISMC controller significantly enhances the control precision and anti-disturbance capabilities of AUVs under low-frequency ocean current disturbances, showcasing exceptional adaptive and self-disturbance rejection performance.

Unmanned agricultural tractor (UAT) represents the advanced stage of autonomous navigation and serves as a core technology in agricultural production. It reduces the operator’s workload, and improves operational accuracy and efficiency. This article reviews three aspects of key autonomous navigation technologies for UATs: perception, path planning and tracking, and motion control. The advantages, and shortages of these key technologies on UATs are clarified by analyzing technical principles and the current research status. We conducted summaries and analyses of existing unmanned navigation solutions for different application scenarios in order to identify current bottleneck issues. Based on the analysis of the applicability of key autonomous navigation technologies on UATs, it can be seen that fruitful research progresses have been achieved. The review also summarizes the common problems in current technologies. The application research on sharing and integrating multi-source data for autonomous navigation are relatively weak. There is an urgent need of high-precision, and high-stability sensing equipment. The universality of path planning methods, and the efficiency and precision of path tracking need to be improved. It is necessary to develop high reliability electrical control modules to enhance motion control performance. Overall, advanced sensors, high-performance intelligent algorithms, and reliable electrical control hardware are key factors in promoting the development of UAT technology.

The port environments have some structures that still need regular control. However, the nature of these environments presents a number of challenges in determining an accurate vehicle position and consequently performing successful image similarity detection. These scenarios, however, can have poor visibility conditions and are highly dynamic, making place recognition difficult because the appearance of a place can change over time. Under these operational conditions, imaging sonars are a promising solution. There are some factors that affect the quality of the captured images, but the fact that they do not suffer from haze is a plus. Therefore, in this paper, a purely acoustic similarity detection method based on forward-looking sonar (FLS) data is proposed to overcome the inherent perceptual problems in a port scenario. Considering the lack of available data in this context and to facilitate the variation of environmental parameters and sensor configurations, a port scenario was simulated using the Stonefish simulator. Experiments were conducted on predefined trajectories near structures. The place recognition approach performs better compared to the results obtained with optical imagery. In general, it provides a good compromise in terms of distinctiveness and achieves a performance of 87.5% when appropriate constraints and assumptions are made.

Beginning with navigation system design, this paper presents a comprehensive strategy for enhancing the search and rescue capabilities of agile mobile robots. Towards this, the autonomous ground vehicle (AGV) utilizes surface classification to determine and prioritize the terrain it is traversing. Our developed system design incorporates real-time terrain data with task objectives at a high level, ensuring that the robot can effectively navigate complex and ever-changing environments. This design, in conjunction with the introduction of a novel lightweight surface classification model, forms the basis of our adaptive terrain perception and decision-making systems, enabling robots such as Jackal to adapt rapidly and make the decisions necessary to complete the task. Subsequently, we exhaustively validated these systems through a series of extensive experiments in a variety of terrains, including normal and mixed terrains, demonstrating their robustness and efficacy in real-life situations.

This article presents a state-of-the-art literature review to understand people’s perceptions and opinions of Autonomous Vehicles (AVs) and the factors that influence AV adoption. A strategic literature search was conducted to select articles for this review. Most of the articles were published within the last five years and they used a household questionnaire survey to collect data. Mostly, they used statistical and econometric methods to evaluate the factors that affect people’s intentions to adopt AVs. The results show that psychological factors often appear as the most important internal factors of people’s willingness to adopt AVs. Additionally, other internal factors such as the socioeconomic profile of individuals and their household, and knowledge and familiarity with AV technologies would affect AV adoption tendencies. User attributes also indirectly affect AV adoption by influencing the psychological factors of users. We identify several critical external factors such as opportunities (e.g., safety and security, low congestion, energy use) and challenges (e.g., system failure, privacy breach, and legal issues), while another influential group includes transportation factors (e.g., travel mode, distance, and time), urban form (e.g., urban/rural, density, land use diversity), affinity to new technology, and the institutional regulatory environment. We discuss some recommendations for policy makers, auto industries, and private stakeholders to formulate policies and strategies to increase market share of AVs. Finally, we identify some limitations of previous studies and provide a blueprint for future research on AV adoption.

The use of digital twins for the development of Autonomous Maritime Surface Vessels (AMSVs) has enormous potential to resolve the increasing need for water-based navigation and safety at the seas. Aiming at the problem of lack of broad and integrated digital twin implementations with live data along with the absence of a digital twin-driven framework for AMSV design and development, an application framework for the development of a fully autonomous vessel using an integrated digital twin in a 3D simulation environment has been presented. Our framework has four layers to ensure that the simulation and the real-world boat as well as the environment are as close as possible. Åboat, an experimental research platform for maritime automation and autonomous surface ship applications, equipped with two trolling electric motors, cameras, LiDARs, IMU and GPS has been used as the case study to provide a proof of concept. Åboat and its sensors, alongwith the environment have been replicated in a 3D simulation environment. Using the proposed application framework, we develop obstacle detection and path planning systems based on machine learning which leverage live data from a 3D simulation environment to mirror the complex dynamics of the real world.

This work aims to develop an autonomous system for the unmanned aerial vehicle (UAV) to land on a moving platform such as the automobile or marine vessels, providing a promising solution for a long-endurance flight operation, a large mission coverage range, and a convenient recharging ground station. Different from most state-of-the-art UAV landing frameworks which rely on UAV’s onboard computers and sensors, the proposed system fully depends on the computation unit situated on the ground vehicle/marine vessel to serve as a landing guidance system. Such novel configuration can therefore lighten the burden of the UAV and computation power on the ground vehicle/marine vessel could be enhanced. In particular, we exploit a sensor fusion-based algorithm for the guidance system to perform UAV localization, whilst a control method based upon trajectory optimization is integrated. Indoor and outdoor experiments are conducted and the result shows that a precise autonomous landing on a 43 X 43 cm platform could be performed.

As Automated Driving Systems (ADS) technology gets assimilated into the market, the driver’s obligation will be changed to a supervisory role. A key point to consider is the driver’s engagement in the secondary task to maintain the driver/user in the control loop. The paper’s objective is to monitor driver engagement with a game and identify any impacts the task has on hazard recognition. We designed a driving simulation using Unity3D and incorporated three tasks: No-task, AR-Video, and AR-Game tasks. The driver engaged in an AR object interception game while monitoring the road for threatening road scenarios. From the results, there was less than 1 second difference between the means of gaming task (mean = 2.55s, std = 0.1002s) to no-task (mean = 2.55s, std = 0.1002s). Game scoring followed three profiles/phases: learning, saturation, and decline profile. From the profiles, it is possible to quantify/infer drivers’ engagement with the game task. The paper proposes alternative monitoring that has utility, i.e., entertaining the user. Further experiments AR-Game focusing on real-world car environment will be performed to confirm the performance following the recommendations derived from the current test.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

Visual-inertial integrated navigation system (VINS) has been extensively studied over the past decades to provide accurate and low-cost positioning solutions for autonomous systems. Satisfactory performance can be obtained in an ideal scenario with sufficient and static environment features. However, there are usually numerous dynamic objects in deep urban areas, and these moving objects can severely distort the feature tracking process which is fatal to the feature-based VINS. The well-known method mitigates the effects of dynamic objects is to detect the vehicles using deep neural networks and remove the features belongs to the surrounding vehicle. However, excessive exclusion of features can severely distort the geometry of feature distribution, leading to limited visual measurements. Instead of directly eliminating the features from dynamic objects, this paper proposes to adopt the visual measurement model based on the quality of feature tracking to improve the performance of VINS. Firstly, a self-tuning covariance estimation approach is proposed to model the uncertainty of each feature measurements by integrating two parts: 1) the geometry of feature distribution (GFD), 2) the quality of feature tracking. Secondly, an adaptive M-estimator is proposed to correct the measurement residual model to further mitigate the impacts of outlier measurements, such as the dynamic features. Different from the conventional M-estimator, the proposed method effectively alleviates the reliance of excessive parameterization of M-estimator. Experiments are conducted in a typical urban area of Hong Kong with numerous dynamic objects, and the results show that the proposed method could effectively mitigate the effects of dynamic objects and improved accuracy of VINS is obtained when compared with the conventional method.

Autonomous aerial refueling technology is an effective solution to extend flight duration of unmanned aerial vehicles, and also a great challenge due to its high risk. For autonomous probe-and-drogue refueling tasks, relative navigation to provide relative position between the receiver aircraft and the refueling drogue is the first and essential step, and vision-based method is the most frequently used. A new monocular vision navigation sensor with image processing strategy consisting of the drogue detection method and the tracking method is developed for autonomous aerial refueling in this paper. In the drogue detection method, thresholding and mathematical morphology method are adopted to eliminate image interference, and contours extraction method is applied to obtain all contours, which are then subsequently checked to achieve target contour of drogue. In the tracking method, a rectangle of interest (ROI) of current frame image is determined by positioning results of last frame, and then processed by the previous drogue detection method. Finally, the proposed image processing strategy in monocular vision navigation sensor is validated using real flight images, which are captured from an autonomous aerial refueling testbed using a micro six-rotor aircraft as receiver aircraft.

Semi-autonomous vehicles (AVs) enable drivers to engage in non-driving tasks but require them to be ready to take control during critical situations. This "out-of-the-loop" problem demands a quick transition to active information processing, raising safety concerns and anxiety. Multimodal signals in AVs aim to deliver take-over requests and facilitate driver-vehicle cooperation. However, the effectiveness of auditory, visual, or combined signals in improving situational awareness and reaction time for safe maneuvering remains unclear. This study investigates how signal modalities affect driver’s behavior using virtual reality (VR). We measured drivers’ reaction times from signal onset to take-over response and gaze dwell time for situational awareness across twelve critical events. Furthermore, we assessed self-reported anxiety and trust levels using the Autonomous Vehicle Acceptance Model questionnaire. Results showed visual signals significantly reduced reaction times, whereas auditory signals did not. Additionally, any warning signal, together with seeing driving hazards, increased successful maneuvering. Analysis of gaze dwell time on driving hazards revealed that audio and visual signals improved situational awareness. Lastly, warning signals reduced anxiety and increased trust. These results highlight the distinct effectiveness of signal modalities in improving driver reaction times, situational awareness, and perceived safety, mitigating the “out-of-the-loop” problem and fostering human-vehicle cooperation.

The rise of the Internet of Things (IoT) has opened up exciting possibilities for new applications. One such novel application is the modernization of maritime communications. Effective maritime communication is vital for ensuring the safety of crew members, vessels, and cargo. The maritime industry is responsible for the transportation of a significant portion of global trade, and as such, the efficient and secure transfer of information is essential to maintain the flow of goods and services. With the increasing complexity of maritime operations, technological advancements such as unmanned aerial vehicles (UAVs), autonomous underwater vehicles (AUVs), and the Internet of Ships (IoS) have been introduced to enhance communication and operational efficiency. However, these technologies also bring new challenges in terms of security and network management. Compromised IT systems, with escalated privileges, can potentially enable easy and ready access to operational technology (OT) systems and networks with the same privileges, with an increased risk of zero-day attacks. In this paper, we first provide a review of the current state and modalities of maritime communications. We then review the current adoption of Software-Defined Radios (SDRs) and Software-Defined Networks (SDNs) in the maritime industry and evaluate their impact, as IoT enablers, on the future of maritime industry operations, safety, and security.

Underwater robotics equipped with visual detection systems have the function of detecting un-derwater artifacts, which is of great significance to deep-sea archaeology. Underwater artifacts are located in complex environments with poor imaging conditions, and the targets have chal-lenging problems such as breakage, stacking, and sediment burial, which causes the marine cul-tural target detection failures. To solve these problems, this paper proposes an underwater cul-tural target detection algorithm based on the deformable deep aggregation network model for underwater robotics exploration. To fully extract the target feature information of underwater targets in complex environments, this paper designs a multi-scale deep aggregation network with deformable convolutional layers. Besides, the BAM attention module is designed for fea-ture optimization, which enhances the potential feature information of the target while weak-ening the background interference information. Finally, the target prediction is achieved through feature fusion at different scales. The proposed algorithm has been extensively validat-ed and analyzed on the collected underwater artifact datasets, and the precision, recall, and mAP of the algorithm have reached 93.1%, 91.4%, and 92.8%, respectively. In addition, the present al-gorithm has been practically deployed on the underwater robotics. In the deep-sea tests, the ar-tifact detection frame rate reaches up to 19 fps, which satisfies the real-time target detection。

The accessibility of public transportation is also known as the last mile problem, and it is one of the main obstacles that affect travelers to choose public transport. Although autonomous vehicles (AVs) have made much progress, they have not been officially put into commercial use. This paper adopts stated preference experiments to explore the impact of shared AVs on train trips’ last-mile travel behavior and takes Wuhan as an example for case analysis. First of all, this paper establishes a structural equation model (SEM) based on the theory of planned behavior to explore the latent psychological variables, including travelers’ attitudes (ATTs), subjective norms (SNs), perceived behavior control (PBC), and behavioral intention to use (BIU) toward AVs. These latent psychological variables are incorporated into the latent class (LC) logit model to establish a hybrid model to study the factors and degree of influence on the travel mode choice for the last mile of train trips. The results show that travelers have preference heterogeneity for the travel mode choice of the last mile of train trips. Through the analysis of LCs, education, career, and income significantly impact the classification of LCs. The latent psychological variables towards AVs have a significant impact on the travel behavior of respondents, but the impacts vary among different segments. Elastic analysis results illustrate that a 1% increase in the travel cost for shared AV in segment 1 leads to a 7.598% decrease in the choice probability of shared AV. Respondents from different segments vary significantly in their willingness to pay, and the value of travel time for high-income groups is relatively higher.

AVs suffer reduced maneuverability and performance due to the degradation in sensor performances in fog. Such degradation causes significant object detection errors essential for AVs' safety-critical conditions. For instance, YOLOv5 performs significantly well under favorable weather but suffers miss detections and false positives due to atmospheric scattering caused by fog particles. Existing deep object detection techniques often exhibit a high degree of accuracy. The drawback is being sluggish at object detection in fog. Object detection methods with fast detection speed have been obtained using deep learning at the expense of accuracy. The problem of the lack of balance between detection speed and accuracy in fog persist. This paper presents an improved YOLOv5-based multi-sensor fusion network that combines radar's object detection with a camera image bounding box. We transformed radar detection by mapping the radar detections into a two-dimensional image coordinate and projected the resultant radar image on the camera image. Using the attention mechanism, we emphasized and improved important feature representation used for object detection while reducing high-level feature information loss. We trained and tested our multi-sensor fusion network on clear and multi-fog weather datasets obtained from the CARLA simulator. Our result shows that the proposed method significantly enhances the detection of distant and small objects. Our small CR-YOLOnet model best strikes a balance between accuracy and speed with an accuracy of 0.849 at 69 fps.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

The capabilities of autonomous mobile robotic systems have been steadily improving due to recent advancements in computer science, engineering, and related disciplines such as cognitive science. In controlled environments, autonomous robots have been able to achieve relatively high levels of autonomy. In more unstructured environments, however, the realisation of autonomous mobile robots remains challenging due to limitations in the robots’ external environment understanding. Many autonomous mobile robots use classical, learning-based or hybrid approaches for navigation. The classical navigation approach typically includes robot perception, localisation, environmental mapping, path planning and motion control stages. More recent learning-based methods may replace the complete navigation pipeline or selected stages of the classical approach. For effective deployment, autonomous robots need to be able to understand their external environments at a sophisticated level according to their intended applications. Therefore, in addition to robot perception, scene analysis and higher-level scene understanding (e.g., traversable/non-traversable, and rough or smooth terrain) are required for autonomous robot navigation in unstructured outdoor environments. A wide number of alternative approaches have been proposed in recent years to attempt to address these scene understanding requirements. This paper provides a comprehensive review and critical analysis of these methods in the context of their applications to the problems of robot perception and scene understanding in unstructured environments, and the related problems of localisation, environment mapping and path planning. State-of-the-art sensor fusion methods and multimodal scene understanding approaches are also discussed and evaluated within this context. The paper concludes with an in-depth discussion regarding the current state of the autonomous ground robot navigation challenge in unstructured outdoor environments and the most promising future research directions to overcome these challenges.

The paper presents the measurement campaign carried out on a real-world motorway stretch of Hungary with the participation of both industrial and academic partners from Austria and Hungary. The measurement included vehicle based as well as infrastructure based sensor data. The obtained results will be extremely useful for future automotive R&amp;D activities due to the available ground truth for static and dynamic content. The aim of the measurement campaign was twofold. On the one hand, road geometry was mapped with high precision in order to build Ultra High Definition (UHD) map of the test road. On the other hand, the vehicles - equipped with differential Global Navigation Satellite Systems (GNSS) for ground truth localization - carried out special test scenarios while collecting detailed data using different sensors. All test runs were recorded by both vehicles and infrastructure. As a complementary task, the available 5G network was monitored and tested. The paper also showcases application examples based on the measurement campaign data, in which the added value of having access to the ground truth labeling and the created UHD map of the motorway section becomes apparent. In order to present our work transparently, a part of the measured data have been shared openly such that interested automotive as well as academic parties may use it for their own purposes.

Autonomous driving systems are increasingly becoming a necessary trend towards building smart cities of the future. Numerous proposals have been presented in recent years to tackle particular aspects of the working pipeline towards creating a functional end-to-end system, such as object detection, tracking, path planning, sentiment or intent detection. Nevertheless, few efforts have been made to systematically compile all of these systems into a single proposal that effectively considers the real challenges these systems will have on the road, such as real-time computation, hardware capabilities, etc. This paper has reviewed various techniques towards proposing our own end-to-end autonomous vehicle system, considering the latest state on the art on computer vision, DSs, path planning, and parallelization.

This study reports on empirical findings of participatory design workshops for the development of a supportive user experience design system in the automotive. Identifying and addressing this area with traditional research methods is problematic due to the different UX design perspectives that might be conflicting and the related automotive domain limitations. To help resolve this problem, we conducted research with 12 User Experience (UX) designers through individual participatory prototyping activities to gain insights on their explicit, observable, tacit and latent needs. These activities allowed us to explore their motivation to use different technologies; the system's architecture; detailed features of interactivity and describe user needs including Efficiency, Effectiveness, Engagement, Naturalness, Ease of Use, Information retrieval, Self-Image awareness, Politeness, and Flexibility. Our analysis led us to design implications that translate participants' needs into UX design goals, informing practitioners on how to develop relevant systems further.

The rapid acceleration of artificial intelligence (AI) has sparked extensive debate about its impact on the safety and security of society. While AI has shown trans- formative potential, particularly in areas such as healthcare and independent structures where it complements productivity and minimizes human error, accu- racy and protection. However, the misuse of artificial intelligence poses real risks, along with threats such as deep counterfeiting, computer cyber-attacks and the manipulation of social behavior through disinformation. These risks vary from privacy and cyber security breaches to moral dilemmas around liability. The unchecked improvement of AI is expected to threaten the social order, so the relationship between innovation and governance is essential so that AI-related threats do not overshadow its benefits. This article offers a detailed assessment and review of the literature that studies the potential dangers that AI poses to society. The cumulative effects underscore the urgent need for comprehensive regulatory frameworks to mitigate these threats.

In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

In autonomous driving systems, high-speed and real-time image processing, along with object recognition, are crucial technologies. This paper builds upon the research achievements in in-dustrial item sorting systems and proposes an object recognition and sorting system for auton-omous driving. In industrial sorting lines, goods sorting robots often need to work at high speeds to efficiently sort large volumes of items. This poses a challenge to the robot's real-time vision and sorting capabilities, making it both practical and economically viable to implement a real-time and low-cost sorting system in a real-world industrial sorting line. Existing sorting systems have limitations such as high cost, high computing resource consumption, and high power consump-tion. These issues lead to the fact that existing sorting systems are typically used only in large industrial plants. In this paper, we design a high-speed, low-cost, low-resource-consumption FPGA (Field-Programmable Gate Array) based item sorting system that achieves similar perfor-mance to current mainstream sorting systems at a lower cost and consumption than existing sorting systems. The recognition part employs a morphological recognition method, which segments the image using a frame difference algorithm and then extracts the color and shape features of the items. To handle sorting, a six-degree-of-freedom robotic arm is introduced in the sorting segment. The improved cubic B-spline interpolation algorithm is employed to plan the motion trajectory and consequently control the robotic arm to execute the corresponding actions. Through a series of experiments, this system achieves an average recognition delay of 25.26ms, ensures smooth operation of the gripping motion trajectory, minimizes resource consumption, and reduces implementation costs.

The vast majority of autonomous driving systems are limited to applications on roads with clear lane markings and are implemented using commercial grade sensing systems coupled with specialized graphic accelerator hardware. This research reviews an alternative approach for autonomously steering vehicles that eliminates the dependency on road markings and specialized hardware. A combination of machine vision, machine learning and artificial intelligence based on popular pre-trained Convolutional Neural Networks (CNN) and Recurrent Neural Networks (RNN) was used to drive a vehicle along roads lacking lane markings (unmarked roads). The team developed and tested this approach on the ACTor (Autonomous Camus TranspORt) vehicle - an autonomous vehicle development and research platform coupled with a low-cost webcam based sensing system and minimal computational resources. The proposed solution was evaluated on real-world roads and varying environmental conditions. It was found that this solution may be used to successfully navigate unmarked roads autonomously with acceptable road following behavior.

The presence of fog in the background can prevent small and distant objects from being detected, let alone tracked. Under safety-critical conditions, multi-object tracking models require faster-tracking speed while maintaining high object-tracking accuracy. The original DeepSORT algorithm used YOLOv4 for the detection phase, and a simple neural network for deep appearance descriptor. Consequently, the feature map generated loses relevant details about the track being matched with a given detection in fog. Targets with a high degree of appearance similarity on the detection frame are more likely to be mismatched, resulting in identity switches or track failures in heavy fog. We propose an improved multi-object tracking model based on the DeepSORT algorithm to im-prove tracking accuracy and speed under foggy weather conditions. First, we employed our camera-radar fusion network (CR-YOLOnet) in the detection phase for faster and more accurate object detection. We proposed an appearance feature network to replace the basic convolutional neural network. We incorporated GhostNet to take the place of the traditional convolutional layers to generate more features and reduce computational complexities and cost. We adopted a segmentation module and fed the semantic labels of the corresponding input frame to add rich semantic information to the low-level appearance feature maps. Our proposed method outperformed YOLOv5 + DeepSORT with a 35.15% increase in multi-object tracking accuracy, a 32.65% increase in multi-object tracking precision, the speed increased by 37.56%, and identity switches decreased by 46.81%.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

This article addresses the problem of formation control of a quadrotor and one (or more) marine vehicles operating at the surface of the water with the end goal of encircling the boundary of a chemical spill, enabling such vehicles to carry and release chemical dispersants used during ocean cleanup missions to break-up oil molecules. Firstly, the mathematical models of the Medusa class of marine robots and quadrotor aircrafts are introduced, followed by the design of single vehicle motion controllers that allow these vehicles to follow a parameterized path individually using Lyapunov based techniques. At a second stage, a distributed controller using event triggered communications is introduced, enabling the vehicles to perform cooperative path following missions according to a pre-defined geometric formation. In the next step, a real time path planning algorithm is developed that makes use of a camera sensor, installed on-board the quadrotor. This sensor enables the detection in the image of which pixels encode parts of a chemical spill boundary and use them to generate and update in real time a set of smooth B-spline based paths for all the vehicles to follow cooperatively. The performance of the complete system is evaluated by resorting to 3-D simulation software, making it possible to simulate visually a chemical spill. Results from real water trials are also provided for parts of the system, where two Medusa vehicles are required to perform a static lawn-mowing path following mission cooperatively at the surface of the water.

In this paper, we present a complete, flexible and safe convex-optimization-based method to solve speed planning problems over a fixed path for autonomous driving in both static and dynamic environments. Our contributions are five fold. First, we summarize the most common constraints raised in various autonomous driving scenarios as the requirements for speed planner developments and metrics to measure the capacity of existing speed planners roughly for autonomous driving. Second, we introduce a more general, flexible and complete speed planning mathematical model including all the summarized constraints compared to the state-of-the-art speed planners, which addresses limitations of existing methods and is able to provide smooth, safety-guaranteed, dynamic-feasible, and time-efficient speed profiles. Third, we emphasize comfort while guaranteeing fundamental motion safety without sacrificing the mobility of cars by treating the comfort box constraint as a semi-hard constraint in optimization via slack variables and penalty functions, which distinguishes our method from existing ones. Fourth, we demonstrate that our problem preserves convexity with the added constraints, thus global optimality of solutions is guaranteed. Fifth, we showcase how our formulation can be used in various autonomous driving scenarios by providing several challenging case studies in both static and dynamic environments. A range of numerical experiments and challenging realistic speed planning case studies have depicted that the proposed method outperforms existing speed planners for autonomous driving in terms of constraint type covered, optimality, safety, mobility and flexibility.

Automotive manufacturers and suppliers develop new vehicle systems, such as Advanced Driver Assistance Systems (ADAS), to increase traffic safety and driving comfort. ADAS are technologies that provide drivers with essential information or take over demanding driving tasks. More complex and intelligent vehicle systems are being developed toward fully autonomous and cooperative driving. Apart from the technical development challenges, training of drivers with these complex vehicle systems represents an important concern for automotive manufacturers. This paper highlights the new evolving requirements concerning the training of drivers with future complex vehicle systems. In accordance with these requirements, a new training concept is introduced, and a prototype of a training platform is implemented for utilization in future driving schools. The developed training platform has a scalable and modular architecture so that more than one driving simulator can be networked to a common driving instructor unit. The participating driving simulators provide fully immersive visualization to the drivers by utilizing head-mounted displays instead of conventional display screens and projectors. The driving instructor unit consists of a computer with a developed software tool for training session control, monitoring, and evaluation. Moreover, the driving instructor can use a head-mounted display to participate interactively within the same virtual environment of any selected driver. A simulation model of an autonomous driving system was implemented and integrated in the participating driving simulators. Using this simulation model, training sessions were conducted with the help of a group of test drivers and professional driving instructors to prove the validity of the developed concept and show the usability of the implemented training platform.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

Autonomous Underwater Vehicles (AUVs) are highly efficient tools for underwater exploration, capable of carrying various payloads to perform specific missions as needed. To ensure the success of these missions and the spatiotemporal accuracy of sampled data, integrated navigation systems and appropriate filtering algorithms are essential. These systems process and merge motion data to provide accurate positioning information. The most commonly used algorithms in integrated navigation systems are Kalman filter and its nonlinear derivatives. Of these, the ensemble Kalman filter (EnKF) is particularly notable for its ability to handle nonlinear systems by incorporating Monte Carlo methods. This study proposes an enhanced adaptive EnKF algorithm to improve the smoothness and accuracy of the filtering process. Instead of the conventional Gaussian distribution, this algorithm employs a Laplace distribution to construct the system state vector and observation vector ensembles, enhancing stability against non-Gaussian noise. Additionally, the algorithm dynamically adjusts the number of vector members in the ensemble using adaptive mechanism by specifying thresholds during filtering, to adapt the requirements of real-world observational settings. Using measured data from field trials, including DVL, GPS, and electronic compass data, we examine the effects of various parameter settings on the algorithm's performance. Optimal parameter settings are identified to fine-tune and verify the filtering algorithm as well as its adaptive capability. The results demonstrate that the enhanced adaptive EnKF algorithm exhibits superior filtering performance in terms of both accuracy and smoothness compared to the conventional EnKF and EKF algorithms. This indicates the significant advantages of our proposed algorithm for AUV navigation.

Real-time image processing is crucial in applications such as video surveillance, diagnostic medicine, and autonomous vehicle systems. Parallel computing is essential to address the demands of real-time processing, but challenges persist in its practical implementation. This review analyzes parallel computing techniques applied to real-time image processing, examining parallel architectures and algorithms, identifying effective applications, and evaluating challenges and limitations. The results of this study will contribute to the development of more efficient solutions for real-time image processing. Keywords: Parallel computing, real-time image processing, video surveillance, diagnostic medicine, autonomous vehicle systems.

The current work reveals the fine tuning between stability zones and randomness of GI/M/1 Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary D/M/1 queueing system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems. A notable application of GI/M/1 queueing model to achieve ultra-low latency of autonomous driving service is highlighted. Concluding remarks associated with future avenues of research are given.

Prokaryotic genomes are dynamic tapestries that are strongly influenced by mobile genetic elements (MGEs), including transposons (Tn’s), plasmids, and bacteriophages. Of these, miniature inverted-repeat transposable elements (MITEs) are undoubtedly the least studied MGEs in bacteria and archaea. This review explores the diversity and distribution of MITEs in prokaryotes and describes what is known about their functional roles in the host and involvement in genomic plasticity and evolution.

The home is becoming a key location for healthcare delivery, including the use of technology driven by autonomous systems (AS) to monitor and support healthcare plans. Using the example of a smart mirror, this paper describes the outcomes of focus groups with people with multiple sclerosis (MS; n=6) and people who have had a stroke (n=15) to understand their attitudes towards the use of AS for healthcare in the home. We thematic analysis to analyse the data. The results indicate that the use of such technology depends on the level of adaptability and responsiveness to the users’ specific circumstances, including their relationships with the healthcare system. A smart mirror would need to support manual entry, responsive goal setting, effective aggregation of data sources and integration with other technology, have a range of input methods, be supportive rather than prescriptive in messaging, and give the user full control of their data. Barriers to adoption include a perceived lack of portability and practicality, lack of accessibility and inclusivity, a sense of redundancy, being overwhelmed by multiple technological devices, and a lack of trust in data sharing. These results inform the development and deployment of future health technologies based on the lived experiences of people with health conditions who require ongoing care.

In various domains such as energy, manufacturing, and maritime, cyber-physical systems (CPS) have seen increased interest. Both academia and industry have focused on the cybersecurity aspects of such systems. The assessment of cyber risks in CPS is a popular research area with many existing approaches that aim to suggest relevant methods and practices. However, few works have addressed the extensive and objective evaluation of the proposed approaches. In this paper, a standard-aligned evaluation methodology is presented and empirically conducted to evaluate a newly proposed cyber risk assessment approach for CPS. The approach, which is called FMECA-ATT&CK is based on Failure Mode, Effects & Criticality Analysis (FMECA) risk assessment process and enriched with the semantics and encoded knowledge in the Adversarial Tactics, Techniques, and Common Knowledge framework (ATT&CK). Several experts were involved in conducting two risk assessment processes, FMECA-ATT\&CK and Bow-Tie, against two use cases in different application domains, particularly an autonomous passenger ship (APS) as a maritime use case and a digital substation as an energy use case. This allows for the evaluation of the approach based on a group of characteristics, namely, applicability, feasibility, accuracy, comprehensiveness, adaptability, scalability, and usability. The results highlight the positive utility of FMECA-ATT&CK in model-based, design-level, and component-level cyber risk assessment of CPS with several identified directions for improvements. Moreover, the standard-aligned evaluation method and the evaluation characteristics have been demonstrated as enablers for the thorough evaluation of cyber risk assessment methods.

The recent advancements in the field of communication have led data sharing to become an integral part of today's smart cities with the evolution of concepts such as the internet of vehicles (IoV) paradigm. As a part of IoV, Electric Vehicles (EVs) have recently gained momentum as authorities have started expanding their Low Emission Zones (LEZ) in an effort to build green cities with low carbon footprints. Energy is one of the key requirements of EVs not only to support the smooth and sustainable operation of EV itself but to also ensure connectivity between the vehicles and infrastructure with controlling devices like sensors and actuators installed within an EV. In this context, renewable energy sources (such as wind energy) dramatically play their parts in the automobile sector towards designing the energy harvesting electric vehicles (EH-EV) to pare the energy reliance on the national grid. In this article, a novel approach is presented to achieve electric generation due to vehicle mobility to support the communication primitives in electric vehicles which enables plenty of IoV use cases in the presence of surplus energy at hand. A small-scale wind turbine is designed to harness wind power for converting it into mechanical power. This power is then fed to the onboard DC generator to produce electrical energy. Furthermore, the acquired power is processed through a regulation circuitry to consequently achieve the desired power supply for the end load, i.e. the batteries installed. The suitable orientation for efficient power generation is proposed on ANSYS-based aerodynamics analysis. The voltages induced by DC generator at No-Load condition are 35V while at Full-Load 25V are generated at rated current of 6.9A, along with the generation of power at around 100W (at constant voltage) at the rated speed of 90 mph for nominal battery charging. Moreover, the acquired data can be monitored via an android application interface by using a Bluetooth module.

In emergency scenarios service vehicles must identify potential route(s) and use the best available route. However, route identification requires intelligent decision-support systems which generally use non-traditional approaches with tools characterised by flexible non-hierarchical structures. Conventional models using group decision-support systems have been applied; however, when used in smart urban environments, emergency response services have limitations in their ability to identify unobstructed paths (routes) in dynamic operating environments. In this paper we introduce a novel path planning method for autonomous vehicle control in emergency situations. The proposed model uses self-organizing maps in an integrated Spiral STC algorithm termed the: Hybrid SOM-Spiral STC model which uses hedge algebras and \emph{Kansei} evaluation in group decision-support. The proposed model has been designed to quantify qualitative factors using sensor derived data processed with human sensibilities and preferences in emergency decision support. The experimental results show that the proposed model achieves significant improvements in group decision-support under dynamic uncertainty. We posit that our novel approach holds the prospect of improvements in the provision of emergency services.

The convergence of artificial intelligence, robotics, and gaming has sparked critical discussions about the nature of life and the potential for artificial systems to replicate biological traits. This paper examines the defining characteristics of life—such as growth, reproduction, regulation, and sensitivity—and applies these criteria to AI-driven game entities and autonomous robots. By reviewing advancements in AI and robotics from 2015 to 2023, and grounding the analysis in biological theories, this study explores whether these artificial systems can be considered "alive" or if they are merely sophisticated simulations. The findings suggest that while artificial systems can mimic life-like behaviours, they lack essential biological traits, such as metabolism and autonomous reproduction. However, human tendencies to anthropomorphise these systems raise ethical and philosophical questions about the boundaries of life and the need for new frameworks to address the evolving role of artificial intelligence and robotics. This paper concludes by proposing directions for future research on the ethical, social, and technical implications of artificial life.

The article discusses the formation of local electric energy systems (LEES) based on renewable energy sources (RSE) as balancing groups in the electric power system (EPS). These systems can function autonomously, providing electricity even in extreme conditions. LEES incorporate small hydroelectric, photovoltaic, and wind power plants, whose output is unstable due to varying natural conditions. To address this, energy storage systems are included to ensure stability and balance. LEES may vary significantly in terms of reliability, power losses, and quality, making it essential to choose the optimal configuration. Optimizing power supply by focusing on individual indicators is discouraged, as it may negatively affect others. To evaluate LEES performance, an integral indicator has been developed, combining the theory of Markov processes and similarity. This indicator compares actual performance with an "ideal" standard, simplifying the assessment of complex systems. It allows comparison of different transmission and distribution options without needing to evaluate all technical and economic details. The proposed integral indicator effectively reflects real operating conditions and assesses the efficiency, quality, and optimality of power supply, while remaining adaptable to partial indicators.

In recent times, the application areas of unmanned aerial vehicles (UAVs) are expanding, and autonomous functions are becoming increasingly prominent, eliminating the need for remote pilot control. Certain applications require the drone to use a docking station autonomously, even for wireless charging. This involves performing autonomous takeoff and landing, where high preci-sion is demanded. These maneuvers can be significantly influenced by environmental factors. The effectiveness of the precision landing function of the DJI Mavic 2 Pro UAV in strong winds is in-vestigated in this article based on experimental measurements conducted outdoors. New findings on the precision landing capabilities of the DJI Mavic 2 Pro UAV are presented in this paper, par-ticularly under windy conditions. The efficiency of precision landing is compared in cases when the precision landing function is enabled versus when it is disabled. It is investigated whether there is a statistically significant difference between the two landing modes in strong winds and it is examined whether the DJI Mavic 2 Pro can perform precision landing on a surface of a specific size in windy conditions. This helps to predict the suitability of the DJI Mavic 2 Pro for precise landing and wireless charging at a docking station in strong winds and high gusts.

Fusing data from many sources helps to achieve higher results of analysis. In this work, we present a new algorithm to fuse data from multiple cameras with data from multiple lidars. This algorithm was developed to increase the sensitivity and specificity of autonomous vehicle perception systems, where the most accurate sensors measuring the vehicle’s surroundings are cameras and lidar devices. Perception systems based on data from one type of sensor do not use complete information and have lower quality. The camera provides two-dimensional images; lidar produces three-dimensional point clouds. We developed a method for matching pixels on a pair of stereoscopic images using dynamic programming inspired by an algorithm to match sequences of amino acids used in bioinformatics. We improve the quality of the basic algorithm using additional data from edge detectors. We also improve the algorithm performance by reducing the size of matched pixels determined by available car speeds. We perform point cloud densification in the final step of our method, fusing lidar output data with stereovision output. We implemented our algorithm in C++ with Python API, and we provided the open-source library named Stereo PCD. This library very efficiently fuses data from multiple cameras and multiple lidars. In the article, we present the results of our approach to benchmark databases in terms of quality and performance. We compare our algorithm with other popular methods.

Background: Rapid advancements in Distributed Ledger Technology (DLT), including blockchain, are foundational to a new era of digital innovation. This innovation has catalyzed the emergence of ‘Decentralized Science (DeSci),’ a new concept and movement that aims to address the challenges of modern science. Objective: Given the novelty of the field of DeSci, this study aims to provide a comprehensive definition of the term as well as explore and conceptualize shared values and guiding principles inherent to DeSci. Methods: In line with the objectives of this study, an exploratory literature review was conducted to identify and synthesize the scholarly and secondary literature. The search and selection process included six databases (PubMed, Google Scholar, Web of Science, IEEE Xplore, arXiv, and Social Science Research Network), and the search period was limited to the last 15 years, from 2008 to 2023. To identify relevant secondary literature, such as articles, reports, blog posts, and website content, a keyword search was conducted in three search engines (Google.com, Bing.com, and Yahoo.com). Owing to the novelty of the concept and movement of DeSci, the exploratory literature review was supplemented by an anonymous online-based expert survey using a combination of single-choice and open-ended questions. The experts were selected based on predefined inclusion criteria, in association with their activities in the field of DeSci. The responses to the single-choice questions were subject to statistical analysis, whereas the open-ended questions were analyzed using qualitative content analysis. Results: Seven studies were selected for evaluation as part of the search and selection process to identify relevant scholarly literature. Following the review of secondary literature, additional 24 publications were included in the analysis. In the expert survey, 39 valid datasets were collected and analyzed. Following the synthesis of the results of the exploratory literature review and expert survey, a comprehensive definition of the term ‘Decentralized Science’ (DeSci) was formulated to reflect recurring themes. As no publications that explicitly discussed or addressed the values or principles of DeSci in the exploratory literature review could be identified, a set of shared values and guiding principles for DeSci were defined based on the results of the expert survey. Conclusion: The results of this study underscore the emerging nature of DeSci, as evidenced by the limited availability of relevant information and scarcity of academic publications. While this study proposes a comprehensive definition of DeSci as well as a set of shared values and guiding principles, the results of this study highlight the importance of ongoing evaluation and validation. Furthermore, the results of this study indicate a clear need for future research in the field of DeSci, emphasizing its dynamic and developing nature.

Among the possible improvements of Autonomous Emergency Braking (AEB) systems, reducing the intensity of the automatic braking process by studying the kinematics and general behavior of the pedestrian while crossing is crucial to determine the progressiveness of the braking, or replacing part of the braking process by an evasive maneuver when a collision is imminent. This paper proposes the integration of an autonomous avoidance system (Automatic Emergency Steering, AES) that acts directly on the steering system to generate an evasive maneuver and avoid a possible pedestrian collision (OPREVU-AES system), as well as the assessment of its effectiveness compared to a commercial AEB system. OPREVU and VULNEUREA are research projects in which INSIA and CEDINT have cooperated to improve driving assistance systems and the safety of pedestrians and cyclists through Virtual Reality (VR) techniques. The analysis of the kinematic and dynamic response of the OPREVU-AES system is conducted in CarSim© software. The effectiveness evaluation procedure is based on the reconstruction of a sample of road vehicle-to-pedestrian crashes (INSIA-UPM database), using the PCCrash® software, and taking as an indicator the probability of head injury severity (ISP). The results show that the AEB system would have prevented part of the collisions, especially after the incorporation of the OPREVU-AES system. In most of the cases where avoidance is not possible, a significant reduction of the ISP is achieved.

This paper develops feasible control strategies and associated system responses to bring an autonomous front-axle bicycle robot from specified initial conditions to final conditions such that a specific performance index is minimized. To solve the problem, the following approach is used: The feasible controls derived from the normal equations of optimality are substituted into the state and the costate systems and form a combined control-free state-costate system which is vectorized to enable and ease the application of a numerical method. A computer program written in Matlab computer programming language, codes a fourth-order Runge-Kutta numerical method and then solve the combined state-costate system of ordinary differential equations. The obtained results are the feasible bicycle robot trajectory, the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations are designed and provided to persuade on the effectiveness and the reliability of the approach.

Imaging lidars are one of the hottest topics in the optronics industry. The need to sense the surroundings of every autonomous vehicle has pushed forward a career to decide the final solution to be implemented. The diversity of state-of-the art approaches to the solution brings, however, a large uncertainty towards such decision. This results often in contradictory claims from different manufacturers and developers. Within this paper we intend to provide an introductory overview of the technology linked to imaging lidars for autonomous vehicles. We start with the main single-point measurement principles, and then present the different imaging strategies implemented 8 in the different solutions. An overview of the main components most frequently used in practice is also presented. Finally, a brief section on pending issues for lidar development has been included, 10 in order to discuss some of the problems which still need to be solved before an efficient final implementation.Beyond this introduction, the reader is provided with a detailed bibliography containing both relevant books and state of the art papers.

Autonomous and cooperative vehicle systems represent a key priority in the automotive realm. Networked driving simulation can be utilized as a safe, cost-effective experimental replica of real traffic environments in order to support and accelerate the development of such systems. In networked driving simulation, different independent systems collaborate to achieve a common task: multi-driver traffic scenario simulation. Yet distinct system complexity levels are necessary to fulfill the requirements of various application scenarios, such as development of vehicle systems, analysis of driving behavior, and training of drivers. With myriad alternatives of available systems and components, developers of networked driving simulation are typically confronted with high design complexity. There are no systematic approaches to date for the design of networked driving simulation in accordance with the specific requirements of the concerned application scenarios. This paper presents a novel design method for networked driving simulation. The method consists mainly of a procedure model that is accompanied by a configuration software. The procedure model includes the necessary phases for the systematic design of application-oriented platforms for networked driving simulation. The configuration software embeds supportive decision-making processes that enable developers to apply the design method and easily create different system models. The design method was validated by generating system models and developing platforms of networked driving simulation for three different application scenarios.

Electric mobility is a global trend and necessity, with electric and solar boats offering a promising alternative for transportation electrification and carbon emission reduction, especially in the Amazon region. This study analyzes the system of a solar boat from the SIMA project, to be implemented at UFPA, using MATLAB software for modeling. The Simulink tool was utilized to model the system, focusing on operational parameters such as module voltage, converter voltage, and speed. Results indicate that the solar boat's operational cost is significantly lower compared to a similar internal combustion model, considering diesel's high consumption and cost. The environmental impact is also reduced, with nearly 72 tons of CO2 emissions avoided annually, thanks to Brazil's renewable energy matrix. Simulations confirmed the project's parameters, demonstrating the efficiency of digital twin technology in monitoring and predicting system performance. The study underscores the importance of digital twins and renewable energy in promoting sustainable transportation solutions, advocating for the replication of such projects globally. Future research should focus on further advancing digital twin applications in electric mobility to enhance predictive maintenance and operational efficiency.

Simultaneous Localization and Mapping (SLAM) is a crucial function for most autonomous systems, allowing them to both navigate through and create maps of unfamiliar surroundings. Traditional Visual SLAM, also commonly known as VSLAM, relies on frame-based cameras and structured processing pipelines, which face challenges in dynamic or low-light environments. However, recent advancements in event camera technology and neuromorphic processing offer promising opportunities to overcome these limitations. Event cameras inspired by biological vision systems capture the scenes asynchronously consuming minimal power but with higher temporal resolution. Neuromorphic processors, which are designed to mimic the parallel processing capabilities of the human brain, offer efficient computation for real-time data processing of event-based data streams. This paper provides a comprehensive overview of recent research efforts in integrating event cameras and neuromorphic processors into VSLAM systems. It discusses the principles behind event cameras and neuromorphic processors, highlighting their advantages over traditional sensing and processing methods. Furthermore, an in-depth survey was conducted on state-of-the-art approaches in event-based SLAM, including feature extraction, motion estimation, and map reconstruction techniques. Additionally, the integration of event cameras with neuromorphic processors, focusing on their synergistic benefits in terms of energy efficiency, robustness, and real-time performance was explored. The paper also discusses the challenges and open research questions in this emerging field, such as sensor calibration, data fusion, and algorithmic development. Finally, the potential applications and future directions for event-based SLAM systems are outlined, ranging from robotics and autonomous vehicles to augmented reality.

Few prior works study self-driving cars by deep learning with IoT collaboration. SDC-Net, which is an end-to-end multitask self-driving car camera cocoon IoT-based system, is one of the research that tackles this direction. However, by design SDC-Net is not able to identify the accident locations, it only classifies if it is a crash scene or not. In this work, we introduce an enhanced design for the SDC-Net system by 1) replacing the classification network with a detection one, 2) adapting our benchmark dataset labels built on the CARLA simulator to include the vehicles bounding boxes while keeping the same training, validation, and testing samples, 3) modifying the shared information via IoT to include the accident location. We keep the same path planning and automatic emergency braking network, the digital automation platform, and the input representations to formulate the comparative study. SDC-Net++ system is proposed to 1) output the relevant control actions, especially in case of accidents: accelerate, decelerate, maneuver, and brake, and 2) share the most critical information to the connected vehicles via IoT, especially the accident locations. A comparative study is also conducted between SDC-Net and SDC-Net++ with the same input representations: front camera only, panorama and bird-eye views, and with single-task networks: crash avoidance only, and multitask networks. Multitask network with a BEV input representation outperforms the nearest representation in precision, recall, f1-score, and accuracy by more than 15.134%, 12.046%, 13.593%, and 5%, respectively. SDC-Net++ multitask network with BEV outperforms SDC-Net multitask with BEV in precision, recall, f1-score, accuracy, and average MSE by more than 2.201%, 2.8%, 2.505%, 2%, and 18.677% respectively.

The introduction of Maritime Autonomous Surface Ship (MASS) through the development of autonomous navigation technologies is expected to bring about new technologies, new vessel types, and new job roles such as remote operation center (ROC) and remote operator (RO). The MASS Code are currently being discussed through Maritime Safety Committee (MSC) of International Maritime Organization (IMO). This code is expected to be adopted in the form of non-mandatory guidelines until 2025, with the goal of establishing mandatory requirements by 2028. Additionally, revisions to the International Convention on Standards of Training, Certification and Watchkeeping for Seafarers (STCW) related to crew training and qualifications are planned for adoption by 2027, which will include requirements for MASS operators. This paper aims to examine the fundamental competencies required for safe MASS operation by remote operators using the Analytic Hierarchy Process (AHP) method, considering the emergence of the new profession of RO. Building upon the 66 Knowledge, Understanding &amp; Proficiencies (KUPs) outlined for marine officer in the STCW Convention, the study seeks to identify the additional competencies necessary for RO and contribute to the development of a training model for the future.

The growing adoption of electric propulsion systems in Maritime Autonomous Surface Ships (MASS) necessitates advancements in shipboard electronics for safe, efficient, and reliable operation. These advancements are crucial for tasks like real-time sensor data processing, control algorithms for autonomous navigation, and robust decision-making capabilities. This study investigates research trends in MASS using bibliographic analysis to inform policy and future research directions in this evolving field. We analyze 3,363 MASS-related articles from the Web of Science database, employing co-occurrence word analysis and latent Dirichlet allocation (LDA) topic modeling. Findings reveal a rapidly growing field dominated by image recognition research. Keywords like "datum," "image," and "detection" suggest a focus on collecting and analyzing marine data, particularly with deep learning for synthetic aperture radar imagery. LDA confirms this, with "Image analysis and classification research" as the leading topic. The study also identifies national and organizational leaders in MASS research. However, research on Arctic routes lags behind other areas. This work provides valuable insights for policymakers and researchers, promoting a deeper understanding of MASS and informing future policy and research agendas for the integration of electric propulsion systems in the maritime industry.

Ultrasonic sensors are inexpensive and can take measurements with high accuracy, even with simple hardware configurations, so they are used in various fields. When multiple ultrasonic sensors exist in the measurement space, crosstalk occurs due to other nodes, which causes measurement errors. Crosstalk includes not only receiving homogeneous signals from other nodes, but also overlap by other signals, and interference by heterogeneous signals. This paper proposes a method that uses frequency sweep keying modulation to be robust against overlap and a faster region-based convolutional neural networks (R-CNN)-based demodulator to reduce the interference caused by heterogeneous signals. The demodulator works by training faster R-CNN with the spectrograms of various received signals and classifying the received signals using a faster R-CNN. Experiments implementing an ultrasonic crosstalk environment showed that compared to on-off keying (OOK), phase-shift keying (PSK), and frequency-shift keying (FSK), the proposed method can implement CDMA even with shorter codes, and is robust against overlap. Compared to correlation-based frequency sweep keying, the time-of-flight error was reduced by approximately 75%. While existing demodulators did not consider heterogeneous signals, the proposed method ignored approximately 99% of the OOK and PSK signals, and approximately 79% of the FSK signals. The proposed method performs better than the existing methods and is expected to be used in various applications.

In modern security situations, tracking multiple human objects in real-time within challenging urban environments is a critical capability for enhancing situational awareness, minimizing response time, and increasing overall operational effectiveness. Tracking multiple entities enables informed decision-making, risk mitigation, and the safeguarding of civil-military operations to ensure safety and mission success. This paper presents a multi-modal electro-optical/infrared (EO/IR) and radio frequency (RF) fused sensing (MEIRFS) platform for real-time human object detection, recognition, classification, and tracking in challenging environments. By utilizing different sensors in a complementary manner, the robustness of the sensing system is enhanced, enabling reliable detection and recognition results across various situations. Specifically designed Radar tag and thermal tag can be used to discriminate friendly and non-friendly objects. The system incorporates deep learning-based image fusion and human object recognition and tracking (HORT) algorithms to ensure accurate situation assessment. After integrating into an all-terrain robot, multiple ground tests were conducted to verify the consistent HORT in various environments. The MEIRFS sensor system has been designed to meet the Size, Weight, Power, and Cost (SWaP-C) requirements for installation on autonomous ground and aerial vehicles.

Abstract: The Micro-Electro-Mechanical System (MEMS) LiDAR point cloud in autonomous vehicles has a large deflection range, which results in slow registration speed and poor applicability. To maximize speed, an improved NDT (Normal Distribution Transform) method that integrates point cloud density features has been proposed. First, the point cloud is reduced using a modified voxel filter and a pass-through filter. Next, the ISS (Intrinsic Shape Signature) algorithm is utilized to analyze the point cloud features and extract keypoints, the 4PCS (4-Point Congruent Sets) algorithm is then employed to calculate the initial pose under the constraints of the keypoint set to complete the coarse registration. Finally, the self-adaptive segmentation model is constructed by using KD-tree to obtain the density features of keypoints, and the NDT algorithm is combined with this model to form an SSM-NDT algorithm, which is used for fine registration. Each algorithm was compared on the autonomous vehicle dataset PandaSet and actual collected data sets, the results show that the novel method increases the speed by at least 60% and takes into account good registration accuracy and strong anti-interference.

Gravity-aided inertial navigation system (GAINS) is an important development in autonomous underwater vehicle (AUV) navigation. An effective path planning algorithm plays an important role in the performance of navigation in long-term underwater missions. By combining the gravity information obtained at each position with the error information from the INS, the posterior Cram\'er-Rao bound (PCRB) of GAINS is derived in this paper. The PCRB is the estimated lower bound of position variance for navigation along the planned trajectory. And the sum of PCRB is used as the minimum cost from the initial state to the current state in the state space, and the position error prediction variance of inertial navigation system (INS) is used as the minimum estimated cost of the path from the current state to the goal state in the A* algorithm. Thus, a path planning method with optimal navigation accuracy is proposed. According to simulation results, traveling along the path planed by the proposed method can rapidly improve the positioning accuracy while consuming just slightly more distance. Even when measuring noise changes, the planned path can still maintain optimal positioning accuracy, and high positioning accuracy is possible for any trajectory located within a certain range of the planned path.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

Connected and Autonomous Vehicle (CAV) combines technologies of autonomous vehicle (AV) and connected vehicles (CV) to develop quicker, more reliable and safer traffic. Artificial Intelligence (AI) based CAV solutions play significant roles in sustainable city. The convergence imposes stringent security requirements for CAV safety and reliability. In practice, vehicles are developed with increased automation and connectivity. Increased automation increases the reliance on the sensor-based technologies and decreases the reliance on driver; increased connectivity increases the exposures of vehicles vulnerability and increases the risk for an adversary to implement a cyber-attack. Much work has been dedicated to identifying the security vulnerabilities and recommending mitigation techniques associated with different sensors, controllers, and connection mechanisms, respectively. However, there is an absence of comprehensive and in-depth studies to identify how the cyber-attacks exploit the vehicles vulnerabilities to negatively impact the performance and operations of CAV. In this survey, we set out to thoroughly review the security issues introduced by AV and CV technologies, analyze how the cyber-attacks impact the performance of CAV, and summarize the solutions correspondingly. The impact of cyber-attacks on the performance of CAV is elaborated from both viewpoints of intra-vehicle system and inter-vehicle system. We pointed out that securing the perception and operations of CAV would be the top requirement to enable CAV to be applied safely and reliably in practice. Also, we suggested to utilize cloud and new AI methods to defend against smart cyber-attacks on CAV.

Leader-follower autonomy (LFA) systems have so far only focused on vehicles following other vehicles. Though there have been several decades of research into this topic, there has not yet been any work on human-vehicle leader-follower systems. We present a system in which an autonomous vehicle — our ACTor 1 platform — can follow a human leader who controls the vehicle through gestures. We successfully developed a modular pipeline that uses artificial intelligence/deep learning to recognize hand-and-body gestures from a user in view of the vehicle’s camera and translate those gestures into physical action by the vehicle. We demonstrate our work using our ACTor 1 platform, a modified Polaris Gem 2 electric vehicle. This work has numerous applications, such as material transport in industrial contexts.

The construction of molecular robotic-like objects that imitate living things is an important challenge for current chemists. Such molecular devices are expected to perform their duties robustly to carry out mechanical motion, process information, and make independent decisions. Dissipative self-organization plays an essential role in meeting these purposes. To produce a micro-robot that can perform the above tasks autonomously as a single entity, a function generator is required. Although many elegant review articles featuring chemical devices that mimic biological mechanical functions have been published recently, the dissipative structure, which is the minimum requirement, has not been sufficiently discussed. This article aims to show clearly that dissipative self-organization is a phenomenon involving autonomy, robustness, mechanical functions, and energy transformation. Moreover, the author details the recent experimental results of an autonomous light-driven molecular device that achieves all of these features. In addition, a chemical model of cell-amplification is also discussed to focus on the generation of hierarchical movement by dissipative self-organization. By reviewing this research, it may be perceived that mainstream approaches to synthetic chemistry have not always been appropriate. In summary, the author proposes that the integration of catalytic functions is a key issue for the creation of autonomous microarchitecture.

This study examines the rationale and perceptions surrounding AI in military technologies, focusing on its application in autonomous weapons systems (AWS), intelligence, surveillance, and reconnaissance (ISR), and decision-support systems (DSS). AI models, such as unmanned aerial and ground platforms, showed high mission success rates, with 92% mission accomplishment, 95% true positive threat identification, and low false alarms. AI's effectiveness surpassed human operators, particularly in response time and threat detection. A global survey revealed mixed opinions: two-thirds believed AI enhances national security, yet 70% opposed autonomous weapons due to ethical concerns, particularly civilian casualties. The study highlights AI's advantages in improving decision-making speed and accuracy but acknowledges challenges such as ethical considerations and public trust in autonomous systems. Future research should address ethical AI models, international humanitarian law (IHL) standards in military operations, human-AI interaction in hazardous environments, and policies related to military robotics and accountability. Understanding and enhancing public awareness of AI in military contexts is also essential.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

Background:As cyber-physical systems (CPS) continue to grow, it is progressively crucial to address the challenges of data protection using artificial intelligence (AI). Objective:The goal of this research is to provide an up-to-date overview of the security and privacy issues of CPS that incorporate AI techniques. Method:To achieve this, the author conducted a systematic literature review, focusing on 35 relevant articles. Results:The data collected from these studies was then categorized into three main areas: 1) different security and privacy issues, 2) application areas and vulnerabilities, and 3) the AI techniques used to address security and privacy concerns. The literature review highlights that intrusion detection and cyberattacks are the most commonly studied areas in CPS, while Machine Learnning (ML)-based attacks and vessel trajectory are less explored. The review identifies various CPS applications such as water treatment, energy, healthcare, and transportation that address security and privacy concerns. However, a relatively small proportion of studies focused on the manufacturing domain. The review also notes that while supervised machine learning algorithms under the classification category are commonly used to address data protection issues, there are comparatively fewer studies that have implemented automation processes using robots and deep learning. Limitations:The articles related to blockchain-based research were not included in this review to focus solely on AI techniques. Conclusion:The results of this analysis indicate that there is a significant need for innovative AI/ML techniques to protect intelligent systems and networks from ML-based security threats.