The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

During the 16th and 17th centuries, Latin American cities adopted earthen construction techniques from European colonizers. As a result, rammed earth (RE) buildings now occupy an important place in Latin America's cultural heritage. However, earthquakes around the world have shown that unreinforced earthen constructions are highly vulnerable. For several years, researchers in northern South America have been proposing a technique that consists of installing confining steel plates (or wooden elements) on both sides of the RE walls forming a grid. This system has shown excellent performance in controlling seismic damage and increasing strength and ductility capacity. Although researchers have tested full-scale one- and two-story earthen walls under pseudo-static loading in the laboratory, and one- and two-story earthen walls at 1:1 and 1:2 scale on uniaxial and biaxial shaking tables, the behavior of a complete reinforced module (one- or two-story) on a shaking table has never been assessed. The present study presents the results of shaking table tests performed on two-story RE modules at 1:4 scale. The experimental data indicate that the retrofit system with confining steel strips was effective in reducing the seismic damage of earthen constructions. In addition, the comparison of the results of the 1:4 scale tests with the 1:2 and 1:1 scale tests previously conducted by the researchers, shows that the acceleration levels of the equivalent prototypes are in the same order of magnitude for the three scales.

Computational Fluid Dynamics (CFD)-based simulation has been the traditional way to model complex industrial systems and processes. One very large and complex industrial system that has benefited from CFD-based simulations is the steel blast furnace. The problem with the CFD-based simulation approach is that it tends to be very slow to generate data. The CFD-only approach may not be fast enough for use in real-time decision-making. To address this issue, in this work, the authors propose the use of machine learning techniques to train and test models based on data generated via CFD simulation. Regression models based on neural networks are compared to tree boosting models. In particular, several areas (tuyere, raceway, and shaft) of the blast furnace are modeled using these approaches. The results of the model training and testing are presented and discussed. The obtained R2 metrics are, in general, very high. The results look promising and may help to improve the efficiency of operator and process engineer decision-making when running a blast furnace.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

Current conventional methods of evaluating microstructures are characterized by a high degree of subjectivity and a lack of reproducibility. Modern machine learning (ML) approaches have already shown great potential in overcoming these challenges. Once trained with representative data in combination with an objective ground truth, the ML model is able to perform a task properly in a reproducible and automated manner. However, in highly complex use cases, it is often not possible to create a definite ground truth. This study addresses this problem using the underlying showcase of microstructures of highly complex quenched and quenched and tempered (Q/QT) steels. A patch-wise classification approach combined with a sliding window technique provides a solution for segmenting entire microphotographs where pixel-wise segmentation is not applicable due to the problem of reproducibly creating unambiguous training masks. Using correlative microscopy, consisting of light optical microscope (LOM) and scanning electron microscope (SEM) micrographs as well as corresponding data from electron backscatter diffraction (EBSD), a training dataset of reference states that covers a wide range of microstructures was acquired in order to train accurate and robust ML models. Despite the enormous complexity associated with the steels treated here, classification accuracies of 88.8% in the case of LOM images and 93.7% for high-resolution SEM images were achieved. These high accuracies are close to super-human performance, especially in consideration of the reproducibility of the automated ML approaches compared to conventional methods based on subjective evaluations through experts.

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as the innovative seismic protection devices. For this, 4, 8 and 12 storey steel frames were designed with 6.5 m equal span length and 4 m storey height. Thereafter, the VDs and BRBs were placed over the height of each frame considering three different configurations. The structures were modeled using SAP2000 finite element program and evaluated by the nonlinear time history analyses subjected to the six natural accelerograms (1976 Gazlı, 1978 Tabas, 1987 Superstition Hills, 1992 Cape Mendocino, 1994 Northridge and 1999 Chi-Chi). The structural response of the structures with and without VDs and BRBs were studied in terms of variation in the displacement, interstorey drift, absolute acceleration, maximum base shear, time history of roof displacement. The results clearly indicated that the application of VDs and BRBs had remarkable improvement in the earthquake performance of the case study frames by reducing the local/global deformations in the main structural systems and satisfied the serviceability.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

700 MPa grade Ti and Nb-Ti microalloyed steels produced by thermo-mechanical control rolled processes (TMCP) were studied to elucidate texture that contributes to delamination and consequent impact toughness. The microstructure of Ti and Nb-Ti steels consisted of ferrite and bainite. Compared with Ti steel, Nb-Ti steel was characterized by a microstructure with finer ferrite and more bainite. The results from tensile and impact tests indicated that there is insignificant change in tensile properties, but toughness was greater in Nb-Ti steel compared with Ti steel. More severe delamination in Nb-Ti steel is attributed to stronger α-fiber (RD ||<110>) texture than Ti steel, especially {100}<110>, {113}<110> and {112}<110> texture. Typical cleavage river patterns were not observed on delaminated fracture surface, instead the cleavage fracture surface indicated some dimples. Interestingly, the impact energy of samples with delamination was greater than samples without delamination in the ductile–brittle transition region. The study suggests that delamination in the ductile–brittle transition zone may also be representative of high toughness.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

The use of new developed high-strength steel in concrete members can reduce steel bars congestion and construction costs. This research aims to study the behavior of concrete columns reinforced with new developed high-strength steel under eccentric loading. Ten reinforced concrete columns were fabricated and tested. The test variables are transverse reinforcement amount and yield strength, eccentricity, and longitudinal reinforcement yield strength. The failure patterns are compression and tensile failure for columns subjected to small eccentricity and large eccentricity, respectively. The same level of post-peak deformability and ductility only can be obtained with lower amount of transverse reinforcement when high-strength transverse reinforcements are used in columns subjected to small eccentricity. The high-strength longitudinal reinforcement can improve bearing capacity and post-peak deformability of concrete columns. Besides, three different equivalent rectangular stress block (ERSB) parameters in predicting bearing capacity of columns with high-strength steel were discussed based on test and simulated results. It is concluded that the Code of GB 50010-2010 overestimates the bearing capacity of columns with high-strength steel, whereas bearing capacities computed using Codes of ACI 318-14 and CSA A23.3-04 agree well with test results.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

This study investigates the application of regression neural networks, in particular the fitrnet model, in predicting the hardness of steels. The experiments involve extensive tuning of hyperparameters using Bayesian optimization and employ 5-fold and 10-fold cross-validation schemes. The trained models are rigorously evaluated, and their performances are compared using various metrics such as mean square error (MSE), root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). The results provide valuable insights into the effectiveness of the models and their ability to generalize to unseen data. In particular, Model 4208 (8-85-141-1) emerges as the top performer with an impressive RMSE of 1.0790 and an R² of 0.9900. The research paper contains an illustrative example that demonstrates the practical application of the developed model in determining the hardenability band for a specific steel grade and shows the effectiveness of the model in predicting and optimizing heat treatment results.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

This study explores the development and characterization of ceramic rod reinforced TWIP (Twinning Induced Plasticity) steel matrix composites, fabricated using a lost foam casting process. The incorporation of ceramic rods aims to enhance the mechanical properties of TWIP steel, which is known for its excellent plasticity. Mechanical testing demonstrated a significant improvement in flexural strength and ductility, with the composite exhibiting over double the strength of the unreinforced TWIP steel. Heat treatment at 500°C for 60 minutes further enhanced these properties, increasing the composite's flexural strength to 1023 MPa and improving its ductility. The observed improvements are attributed to the synergistic effects of the hard ceramic reinforcement and the ductile matrix, as well as the microstructural modification conferred by heat treatment. These findings suggest that ceramic rod reinforced TWIP steel composites are promising materials for applications requiring a combination of high strength and ductility.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

To address the problems of lining cracking and spalling of tunnel structures in coastal areas under the influence of special geologic conditions, environmental loading, and the coupling effect of chemical erosion effects, hybrid fibers were introduced to fly ash concrete in this study. The working performance, compressive strength, split tensile strength, and flexural strength of the hybrid fiber fly ash concrete were tested.The NEL chloride diffusion coefficient under steady-state conditions and the durability test for resistance to sulfate corrosion were carried out. Thus, in-depth analyses of the comprehensive performance of the hybrid fiber fly ash concrete used for tunnel lining were carried out and the damage mechanism were explored. The results showed that the hybrid fiber fly ash concrete exhibited higher strength compared to the control group concrete. However, when the fibers exceeded a certain dosage, the reduction in the working properties of the concrete structure led to the creation of larger pores in the matrix structure, which in turn affected the mechanical properties of the concrete. The most significant reduction in NEL chloride diffusion coefficient was observed when both steel fibers and coconut fibers were added at 1.0 % volumetric parameter, compared to the control group. The apparent state and compressive strength after sulfate corrosion were also minimally affected. This study ensured that the mechanical properties of the concrete were improved and also substantially improved the corrosion resistance of the matrix, providing a scientific basis for the performance improvement of tunnel lining concrete, confirming that steel-coconut fibers hybrid fiber fly ash concrete has a great potential to improve the structural load bearing capacity and durability, and may provide theoretical support for the continued use of tunneling projects and construction processes.

The paper presents the problem of damage detection in steel girders. Static displacements at the selected point of the structure play the role of measured variables. Structural response signal decomposition is performed according to the Mallat pyramid algorithm, which is used to perform the discrete wavelet transform (DWT). This procedure allows us to quite well determine the location of structural damage. The geometry and the placement of any defective part of the structure may have a random character. It can be assumed that the random processes occurring in the broadly understood structure mechanics are Gaussian in nature. The first four probabilistic moments are estimated using three approaches independent: semi-analytical (SAM), perturbative (SPT), and Monte-Carlo simulations (MCS). The semi-analytical random approach seems to be the most optimal due to the necessary computation time. The incorporation of the mathematical stochastic apparatus into the classical (deterministic) analysis of the statics of the structure makes it possible to estimate the reliability measures of the analyzed girder.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

In this study, we investigated the effects of three surface treatment techniques on 316L stainless steel, low-temperature immersion corrosion, shot peening followed by immersion corrosion, and electrochemical corrosion. Surface alterations were analyzed using scanning electron microscopy, Raman spectroscopy, and α-step thin-film thickness profiling. Human osteoblast adhesion was evaluated using Liu’s stain and metallographic optical microscopy. The results revealed weak cell adhesion after low-temperature immersion and shot peening followed by immersion corrosion. By contrast, electrochemical corrosion, particularly with a high current density and low corrosive solution concentration, resulted in a uniformly corroded surface, thus promoting dense cell adhesion. All three techniques resulted in porous oxide layers. Overall, our experimental findings highlighted shot peening (1 kg/cm2 for 20 s) and electrochemical corrosion (0.5 M HCl) as effective processes. Electrochemical corrosion produced uniformly dense corrosion pits, whereas shot peening produced semicircular grooves with small corrosion pits, both favorable for cell adhesion. Electrochemical corrosion also yielded excellent cell adhesion, emphasizing its suitability for biomedical activity. We developed a process for creating a porous surface layer and thereby enhancing the cell adhesion to 316L stainless steel for potential biomedical implant applications.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

The possibility of increasing the resource of steel fingers working in tandem with bronze bushings by plasma-electrolytic nitrocarburizing of the surface of medium carbon steel is shown. The phase composition, microhardness, morphology and surface roughness were studied. Tribological tests were carried out under dry friction conditions according to the shaft-pad scheme. It has been established that plasma-electrolytic nitrocarburizing of the surface of medium carbon steel at a temperature of 700 °C for 5 minutes leads to a decrease in a friction coefficient by 2.3 times, weight wear of steel by 24.9 times, and bronze counterbody by 5.9 times. At the same time, the contact stiffness increases 2.6 times. The type of wear is fatigue with dry friction and plastic contact. Changes in tribological characteristics are associated with the high hardness of the hardened steel surface together with the influence of dispersed nitrides and iron carbonitrides distributed in it.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

This article reports on the comparative study of the hot deformation behaviour of virgin (steel A) and rejuvenated heat treatment creep-exhausted (steel B) P91 steels. Hot uniaxial compression tests were conducted on the two steels at the deformation temperature range of 900°C-1050°C and a strain rate range of 0.01-10s-1 to 0.6 strain using Gleeble® 3500 equipment. The results showed that the flow stress largely depends on the deformation conditions. The flow stress for the two steels increased with an increase in strain rate at a given deformation temperature and vice versa. The flow stress-strain curves exhibited a dynamic recovery as the softening mechanism. The material constants determined using Arrhenius constitutive equations were: stress exponent was: steel A (5.76) and steel B (6.67), and the apparent activation energy was: steel A (473.1 kJ mol-1) and steel B (564.5 kJmol-1). From these results, steel A exhibited better workability than steel B. Statistical parameters analyses showed that the flow stress for the two steels had a good correlation between the experimental and predicted data. Pearson’s correlation coefficient (R) was: steel A (0.97) and steel B (0.98). The Average Absolute Relative Error (AARE) values were: 7.62% (steel A) and 6.54% (steel B). The study shows that the Arrhenius equations can effectively describe the flow stress behaviour of P91 steel, and this method is applicable to the industrial metalworking process.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

The change in the value of the breaking energy is discussed here for selected steel grades used in building structures after subjecting the samples made of them to episodes of heating in the steady-state heating regime and then cooling in a simulated fire conditions. These changes were recorded based on the instrumented Charpy impact tests, in relation to the material initial state. The S355J2+N, 1H18N9T steels and also X2CrNiMoN22-5-3 duplex steel were selected for detailed analysis. The fire conditions were modelled experimentally by heating the samples and then keeping them for a specified time at a constant temperature of: 600°C (first series) and 800°C (second series), respectively. Two alternative cooling variants were investigated in the experiment: slow cooling of the samples in the furnace, simulating the natural fire progress, without any external extinguishing action, and cooling them in water mist simulating an extinguishing action by a fire brigade. The temperature of the tested samples was set at the level -20oC and alternatively at the level + 20oC. The conducted analysis is aimed at assessing the risk of sudden, catastrophic fracture of load-bearing structure made of steel degraded as a result of a fire previously occurred with different development scenarios.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

This study investigates the failure of a roof with steel truss construction of a factory building in Tekirdag in North-western part of Turkey. The failure occurred under hefty weather conditions including thunderbolt, lightning strikes, heavy rain and fierce winds. In order to interpret the reason for the failure, the effects of different combinations of factors on the design and dimensioning of the roof are checked. Therefore, finite element analysis is performed several times under different assumptions and considering different factors aiming to determine the dominant ones that are responsible for the failure using the commercial software Abaqus (Dassault Systèmes, Vélizy-Villacoublay, France). Each loading condition gives out a characteristic form of failure. The scenario with the most similar form of failure to the real collapse is considered as the most likely scenario of failure. Also, the factors included in this scenario are expected to be the responsible factors for the partial collapse of the steel truss structure.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

The detection of temporary color steel buildings and the analysis of their spatiotemporal patterns and characteristics are of great importance in many developing cities, because areas densely distributed with color steel buildings are usually problematic regions with high population density, sustainable development and risk level, which are challenging for local governments. Using the high-resolution satellite images of the Anning District, Lanzhou City, China as the case study, this paper first extracts the information of the color steel buildings for two different periods. Then the spatiotemporal distributional characteristics of the color steel buildings are analyzed, both at small scale (temporary buildings) and large scale (planthouses, warehouses, etc.). Finally, this paper utilizes kernel density estimation, Delaunay triangulation and Voronoi diagrams to examine the spatial distribution, aggregation and proximity characteristics of the color steel buildings. Our experiments show that the temporal and spatial differences of urban development, the phased characteristics and urban space are represented by various types of color steel buildings. Thus, there are some robust coupling relationship between color steel buildings, urban spatial form and urban development.

Cold gas-dynamic spray (cold spray) is an evolving coating deposition and restoration technology in which particles are deposited above the sonic speed. This paper presents the non-destructive three-dimensional characterization of cold sprayed stainless steel coating. The visualization of coating morphology and volumetric porosity, and the analyses of porosity size and spatial distributions confirmed that dense stainless steel coating with non-connected, micron-sized gradient porosity is successfully produced by cold spray. The suitability of X-ray tomography for characterizing cold sprayed coatings is assessed.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

This study presents the experimental and analytical evaluations on an innovative connection class under cyclic loading. The connection was an H- or I-shaped section as a short stub column (SSC) between the end-plate and the column. The stub section was bolted to the column flange on the one side and bolted to the beam along with the welded end-plate on the other side. Stiffeners were installed on the webs and flanges of the beam and stub to ensure the necessary stiffness of the connection. The variables included thickness of stub flange/web and height of stub web. The cyclic loading was applied on a sample of the proposed connection according to AISC ANSI/AISC 341-16 loading protocol. Experimental observations displayed that the proposed connection, one can either employ hot rolling sections or create the connection as a plate girder, in which case the flange thickness and stub web, as well as the distance between two flanges and their height, was obtained according to the demand and performance of the structure. The optimum cross-section of the stub was then obtained. Also, the analytical model was calibrated using the finite element method (FEM), and its performance was confirmed. The effective parameters of the proposed connection were determined by modeling in the FEM software, and the design method was presented.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

A recently published article posited the use of polymer matrix composites (PMCs) as a replacement material for low-carbon steel (LCS) in large power transformer (LPT) tanks [1]. PMCs offer potential advantages such as weight reduction, corrosion prevention, and self-healing of the tank material which may not be achievable with traditional LCS. LCS can arrest ballistic projectiles at relatively low velocities, but at higher velocities, penetration can occur leading to a potential major transformer failure. Numerical simulations of steel projectile impacts upon LCS plates and glass and/or carbon fiber polymer composite laminates showed that with sufficient thickness both could prevent projectile penetration. This prevention was especially efficient when the plates were coated with a high strain rate sensitive material such as polyurea (PU). Our simulations show that the addition of a 3 mm coating of PU to a standard 10 mm thick LCS plate used in LPT tanks could prevent penetration of a 400 m/s steel projectile. For PMC plates, the simulations with the same projectile velocity showed three times faster deceleration with a 3 mm PU coating than without the coating. Thus, two realistic approaches to improving the ballistic protection of LPTs are presented. In addition to their other advantages, this research clearly shows that PMCs with the coating could provide significant ballistic protection for the next generation of LPT tanks.

The application possibilities of austenitic stainless steels in high friction, abrasion and sliding wear conditions are limited by their inadequate hardness and tribological characteristics. In order to improve these properties, thermochemical treatment of their surface by plasma nitriding is suitable. This article is focused on corrosion resistance of the conventionally plasma nitrided AISI 304 stainless steel (530 °C, 24 hours) in 0.05 M and 0.5 M sodium chloride solutions at room temperature (20 ± 3 °C), tested by potentiodynamic polarization and electrochemical impedance spectroscopy. The optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy are used for the nitrided layer characterization. The experiment results point to a significant reduction in corrosion resistance after performed plasma nitriding even in a solution with a very low chloride concentration (0.05 mol/L).

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

This study reveals the essential load-bearing characteristics of the steel-concrete composite floor system under fire conditions applying structural stressing state theory. Firstly, the strain data in the entire process of the fire test are modeled as state variables which can present the slab’s stressing state evolution characteristics; Then, the state variables are used to build the stressing state mode and the parameter characterizing the mode. Further, the Mann-Kendall criterion is adopted to detect the leap points in the evolution curves of the characteristic parameters during the entire fire exposure process. Also, the evolution curves of the stressing state modes are investigated to verify the leap profiles around the leap/characteristic points; Finally, the detected leap points are defined as the failure starting points and elastoplastic branching points, which is unseen in the past researches focusing on the failure endpoint defined at the ultimate load-bearing state of the composite floor system. The failure starting point and the elastoplastic branching point are the embodiment of natural law from quantitative change to quality change of a system rather than an empirical and statistical judgment. Hence, both characteristic points avoidably exist in the strain data of the composite floor system undergoing the fire process, which can be revealed through the proper modeling methods and update the existing theories and methods on structural analysis and design in fire.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

Additive manufacturing (AM) or 3D printing of metals is gaining popularity due to its flexibility in fabricating parts with highly complex designs, as well as simplifying manufacturing steps and optimizing process times. In this investigation, 17-4 PH stainless steel was additively manufactured using Laser-Powder Bed Fusion (L-PBF), followed by functionalization through a DUPLEX treatment. This treatment involved a plasma-assisted nitriding process, followed by deposition of an arc-PVD c-Al0.7Cr0.3N hard coating. The microstructural modifications resulting from plasma nitriding (such as the formation of Fe2,3N and Fe4N, and the αN or expanded martensite phases), and the surface improvements with the c-Al0.7Cr0.3N coating on the 3D-printed 17-4 PH steel, are evaluated in comparison to conventionally manufactured 17-4 PH steel. These microstructural characteristics are correlated with the mechanical response of the treated surfaces. As a result of the plasma nitriding process, the hardness of the 3D-printed 17-4 PH SS increased by approximately 260%. The wear, measured through dynamic and static scratch-testing, was reduced by approximately 31%. This improvement was attributed to the modification of adhesive failure mechanisms, leading to a reduction in wear volume, improved coating adhesion, and enhanced scratch resistance.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Upon the implementation of the European Union Carbon Border Adjustment Mechanism (CBAM), substantial challenges are anticipated to impact the international trade of Chinese steel products. To safeguard the competitiveness of Chinese steel products on the global stage, this paper establishes a tripartite evolutionary game model, involving large steel enterprises, small and medium-sized steel enterprises, and the government. The model integrates collaborative emission reduction and free-riding benefits among enterprises, along with the government's dynamic subsidies and penalties. The paper analyzes the evolutionary trends and stable states of the three parties during different stages of CBAM, including a sensitivity analysis of key parameters. The findings indicate that large enterprises demonstrate a heightened sensitivity to CBAM, while small and medium-sized enterprises are more significantly influenced by free-riding benefits. Government intervention should be strategically timed and incline towards passive management during the strengthening phase of CBAM. Additionally, the refinement of the Chinese carbon market emerges as an effective means to counter CBAM. This paper provides theoretical support for how steel enterprises and the government can respond to CBAM, aiding stakeholders in selecting optimal strategies during different implementation stages and mitigating the impacts of CBAM to the maximum extent possible.

The bacterial adhesion to food contact surfaces is a threat to human health, as these surfaces can serve as a reservoir of pathogenic bacteria. Escherichia coli is a biofilm-forming bacterium involved in surface contamination. Despite the application of disinfection protocols, contamination continues to occur. Hence, new effective and sustainable approaches are needed. Bacteriophages (or simply phages), viruses that only infect bacteria, have proven to be effective in reducing biofilms. Here, phage phT4A was applied to prevent and reduce E. coli biofilm on plastic and stainless steel. The assays were performed in Tryptic Soy Broth (TSB), at 25 °C. The biofilm formation capacity of phage-resistant and sensitive bacteria, after treatment, was also evaluated. Maximum reductions on E. coli biofilm of 5.5 log colony forming units (CFU)/cm2 (after 6 h) and 4.1 log CFU/cm2 (after 9 h), on plastic and stainless steel, respectively, were observed. In the prevention assays, phage prevented biofilm formation in 3.2 log CFU/cm2, after 12 h. Although the emergence of phage-resistant bacteria has been observed during phage treatment, a lower biofilm formation capacity was observed by phage-resistant bacteria comparatively to phage-sensitive bacteria. Overall, phages have shown to be a promising approach to decontaminate food handling surfaces.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors, providing an overview of their unique characteristics and challenges. The paper delves into specific elements related to hydrogen technologies, shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology, the paper offers valuable insights into its suitability for specific applications. Finally, through a particular analysis focused on the steel sector, the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this particular context. By emphasizing the steel sector as a focal point, the authors contribute to a more nuanced understanding of hydrogen's role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+&gt;Ca2+&gt;Mg2+ and HCO3- &gt;Cl- &gt;SO42-.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

The post-weld heat treatment (PWHT) cracking susceptibility of a coarse grain heat-affected zone (CGHAZ) in SA213-T23 (2.25Cr-1.6W steel), used for boiler tubes employed in thermal power plants, was investigated using a Gleeble thermal cycle simulator. The PWHT cracking susceptibility test was performed at 650℃, 700℃ and 750℃, and it can be judged that the lower the reduce of area, the more susceptible it is to PWHT cracking. The results of the test also showed higher cracking susceptibility at 650℃ and 700℃, mostly involving intergranular fracture, while at 750℃, transgranular fracture was exhibited. Therefore, the PWHT cracking susceptibility is considered to be closely related to grain boundary. The microstructure of the simulated CGHAZ and PWHT at 650℃, 700℃and 750℃ was observed after etching with nital and alkaline sodium picrate etchants. Alkaline sodium picrate etched microstructures showed a white band at the grain boundary at 650℃, 700℃ and 750, that did not appear in nital etching. Analysis of the white band using EPMA, TEM and nanoindentation revealed that it was intergranular ferrite depleted with C, W and Cr as compared to that in the matrix. Based on these results, we investigated the mechanism of intergranular ferrite formation during PWHT and its effect on PWHT cracking susceptibility at 650℃, 700℃ and 750℃.

The awareness of the vulnerability of existing structures under both seismic and energy viewpoints highlight the need to develop integrated retrofit solutions combining the structural and thermal performances. In this perspective, the study explores the efficacy of the Resisto 5.9 Tube system, a seismic coat that improves the seismic behaviour of masonry and reinforced concrete (RC) structures, also enhancing their energy performances, thanks to the thermal coat integrated in the basic steel system. The research involves the application of a design procedure specifically developed for this retrofit system from the seismic perspective. Once all the system elements are designed, non-linear static analyses are performed with a Finite Element software comparing the building’s seismic performances before and after the application of Resisto 5.9 Tube. The results demonstrate a significant increase in seismic safety coefficient, proving that this intervention type can be useful to obtain the seismic upgrading of existing RC buildings.

We present an autonomous system that remotely monitors the state of reinforced concrete structures. This system performs the real-time follow-up of the corrosion rate of rebars (iCORR), along with other relevant parameters, such as temperature, corrosion potential (ECORR) and electrical resistance of concrete (RE), at many of structures’ control points by using embedded sensors. Its corrosion sensor is stressed, to which a novel electrochemical polarization technique is applied. The custom electronic system manages the sensor network, consisting of a measurement board per control point connected to a central single-board computer in charge of processing measurement data and uploading results to a server via 4G connection. In this work, we report the results obtained after implementing the sensor system into a reinforced concrete wall, where two well-differentiated representative areas were monitored. The obtained corrosion parameters showed consistent values. Similar conclusions are obtained with ECORR recorded in rebars. With the iCORR follow-up the corrosion penetration damage diagram is built. This diagram is particularly useful for identifying critical events during the corrosion propagation period and to be able to estimate structures’ service life. Hence the system is presented as a useful tool for the structural maintenance and service life predictions of new structures.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

The paper delves into the critical issue of damage detection within the guy cable of a truss steel mast, a pivotal component in structural integrity. It introduces a model wherein damage manifests as a localized cross-section reduction in a single element of the cable. Employing Discrete Wavelet Transform (DWT), a pioneering methodology, the study scrutinizes the behavior of the affected elements through static structural analyses. Signal decomposition via the Mallat pyramid algorithm facilitates comprehensive examination. Static displacements at the connection point between the cable and the truss mast serve as the measured variables. Through systematic investigation, the paper evaluates the impact of damage size and location, external loading force, and cable tension force on the efficacy of the proposed approach. Utilizing data derived from Finite Element Method (FEM) computations for wavelet analysis the authors substantiate the findings with numerical examples, thus offering valuable insights into damage detection strategies for structural health monitoring and engineering applications.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

The research object was the stress-strain state of shear stud bonds in the contact joint of steel-concrete beams. The work diagrams for three types of anchors are given. Based on the analysis of numerical and full-scale experiments, analytical dependencies are proposed that reflect the actual operation of anchor ties. Comparisons of the calculation results by analytical formulas and comparisons with numerical and full-scale experiment data are given. Numerical studies have revealed the pattern of the stress-strain state of the contact joint, the stages of development of cracks in the concrete flange, and the sequence of development of deformations in anchor ties. It was revealed that vertical shear studs bonds have an increased bearing capacity, although displacements are 1.5-2 times greater than those of loop-shaped anchor ties.

The article presents a hybrid method for calculating the chemical composition of steel with the required hardness after cooling from the austenitizing temperature. Artificial neural networks and genetic algorithms were used to develop the model. Based on 550 diagrams of continuous cooling transformation (CCT) of structural steels available in the literature, a dataset of experimental data was created. Artificial neural networks were used to develop a hardness model describing the relationship between the chemical composition of the steel, the austenitizing temperature, and the hardness of the steel after cooling. A genetic algorithm was used to identify the chemical composition of the steel with the required hardness. The value of the objective function was calculated using the neural network model. The developed method for identifying the chemical composition was implemented in a computer application. Examples of calculations of mass concentrations of steel elements with the required hardness after cooling from the austenitizing temperature are presented. The model proposed in this study can be a valuable tool to support chemical composition design by reducing the number of experiments and minimizing research costs.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

Due to the imbalance between the supply and demand of oxygen, the oxygen system of iron- and steel-making enterprises in China has problems with high oxygen emission and high pressure in the pipelines, resulting in the energy consumption of oxygen production being high. To relieve this problem, using a large-scale iron- and steel-making mill as a case study, the research on demand forecasting and optimal scheduling of the oxygen system was carried out. The ARIMA model and the GABP model are employed to forecast oxygen demand. Based on the forecast results, an optimal scheduling model for the oxygen system was developed to conduct optimal scheduling. The case study shows that based on the oxygen demand forecast and the optimal scheduling, the oxygen emission and the pipeline pressure in the studied iron- and steel-making enterprise can be significantly reduced, thereby achieving considerable energy-saving effects and economic benefits. Specifically, the following conclusions are obtained: (1) For the oxygen demand forecast, the prediction accuracy of the GABP model is better than that of the ARIMA model. The average MAPE of the 12 sets of data of the ARIMA and GABP models are 23.8% and 20.2%, respectively. (2) By comparing the scheduling results and the field data, it is found that after the scheduling, the amount of oxygen emission has decreased by 6.32%, the pipeline pressure has decreased by 0.61%, and the energy consumption of oxygen compression has decreased by 1.6%. Considering both the oxygen emission loss and the energy consumption of oxygen compression, the total power consumption of the oxygen system is reduced by 1.38%, which saves the electricity cost of about 9.03 million RMB per year.

A medium-Mn steel was processed by a route involving twin-roll strip casting, hot-rolling and quenching and partitioning with different quenching temperatures. The effects of quenching temperature on the microstructure and mechanical properties were studied. It was found primary martensite and retained austenite (RA) were obtained at the quenching temperature of 140–180 °C, while primary martensite, RA and secondary martensite were obtained when the quenching temperature was 220–300 °C. With increase in quenching temperature from 140 to 260 and to 300 °C, RA fraction first increased from 15.4% to 31.8% and then decreased to 16.6%. The sample at quenching temperature of 220 °C yielded the mechanical properties with yield strength of 992 MPa, tensile strength of 1159 MPa and total elongation of 20.4%. The superior mechanical properties were achieved by an optimum combination of high RA fraction (26.5 vol%), appropriate mechanical stability of RA and a small amount of secondary martensite.

A novel prediction model for crack development of reinforced concrete (RC) piles with localized chloride corrosion in marine environment is proposed. A discrete method is used to solve the corrosion pit radius model and a crack extension model is developed to investigate the initiation and extension of cracks. The maximum corrosion degree of reinforced concrete pile is predicted according to the limit crack criterion, and finally a sensitivity analysis is carried out on the important parameters of crack extension. The results show that the radius of corrosion pit, the depth corrosion pit and cross-sectional area loss of reinforcement gradually increase as the corrosion level increases. The loss of local reinforcement section at crack initiation decreases with the increase of the ratio of concrete cover to initial diameter, and increases with the increase of pitting factor. The required pit depth for reinforcement cracking increases with the increase of the ratio of concrete cover thickness to diameter. The loss of cross-sectional area of reinforcement and the radius of corrosion pit increase with the increase of initial diameter of reinforcement. Increasing the pitting factor will reduce the pit depth and make the crack width develop faster before reaching the limit crack width. Increasing the concrete cover thickness can provide an improvement in the propagation of cracks. A comparative analysis shows that the localized corrosion pattern is more in conformity with marine engineering practice.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

The shield tunnels inevitably endure various damage with the service time increasing. Meanwhile, steel corrugated plate has been used extensively in multiple conditions and proved effective to strengthen the segmental joints by full-scale tests. A numerical model is proposed to probe the feasibility of using new Stainless Steel Corrugated Plate (SSCP) to reinforce the shield tunnel segments. A new method, called virtual tracking element technology, is employed to achieve the simulation of realistic stress state of the segmental joint. Moreover, the segmental joint component analysis and parametric study are conducted based on the numerical model. The results demonstrate that: (1) the virtual tracking element technology proves valid and efficient to simulate the secondary stress state of segmental joint; (2) SSCP reinforcement is not fully utilized when the grade of segmental concrete is C50 and it has abundant safety margin for potential overload; (3) SSCP reinforcement is well-performed regardless of the burial depth and reinforcement in advance is recommended.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

For the generation of representative volume elements a statistical description of the relevant parameters is necessary. These parameters usually describe the geometric structure of a single grain. Commonly, parameters like area, aspect ratio and slope of the grain relative to the rolling direction are applied. However, usually simple distribution functions like log normal or gamma distribution are used. Yet, these do not take the interdependencies between the microstructural parameters into account. To fully describe any metallic microstructure though, these interdependencies between the singular parameters need to be accounted for. To accomplish this representation, a machine learning approach was applied in this study. By implementing a Wasserstein generative adversarial network, the distribution, as well as the interdependencies could accurately be described. A validation scheme was applied to verify the excellent match between microstructure input data and synthetically generated output data.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

Stainless steel grade AISI 304 is one of the most widespread modern structural material, alas its sliding wear and cavitation wear resistance are limited. Thus, AlTiN and TiAlN coatings can be deposited for increasing the resistance to wear of stainless steel components. The aim of the work was to investigate the cavitation erosion and sliding wear mechanisms of magnetron sputtered AlTiN and TiAlN coatings deposited on SS304 stainless steel. Films surface morphology and structure were examined using a profilometer, light optical microscope (LOM) and scanning electron microscope (SEM). The mechanical properties (hardness, elastic modulus) were tested by nanoindentation tester. The adhesion of deposited coatings was determined by means of the scratch test and Rockwell test. Cavitation erosion tests were performed according to ASTM G32 (vibratory apparatus) with stationary specimen procedure. Sliding wear tests were conducted using a nano-tribo testes i.e. ball-on-disc apparatus. Wear mechanisms are strongly contingent upon the structure and morphology of the tested materials. In relation to stainless steel substrate, the PVD films present a superior resistance to sliding wear and cavitation erosion. Higher resistance was noticed for AlTiN than for TiAlN film, mainly due to its superior hardness and elastic modulus. Cavitation erosion mechanism of both, AlTiN and AlTiN coatings is prone to embrittlement, imputable to fatigue processes that result in coating rupture and spallation that consist in coating fragmentation, formation of pits and finally detachment from the substrate. Additionally, films nanoindentation results measured before and after cavitation testing indicate changes in coatings structure, that acknowledged wear mechanism that starts with coating internal delamination in flake spallation mode. In contrary to PVD coatings, steel substrate is characterized by developed cavitation erosion wear with roughened surface and plastically deformed, semi-brittle, eroded surface. Sliding wear of thin films is based on micro-ploughing mechanism. For stainless steel adhesive sliding wear mode and plastic deformation with smearing, material transfer and grooving were observed. It was confirmed that various fluid machinery components made from austenitic stainless steel that undergo cavitation erosion, can be prevented by deposition of AlTiN and TiAlN films.