Theoretical approaches were applied to study the effect of magnetic field and heat transfer on the flow of blood plasma through an asymmetric arterial segment. The plasma was considered to be unsteady, laminar and an incompressible fluid through non-uniform arterial segment in a two-dimensional flow. Axial velocity, pressure gradient, stream function and pressure shift per wavelength were evaluated in blood plasma flow in arteries by use of coupled linear partial differential equations, solved with the help of Finite difference method. The corresponding initial and boundary conditions were obtained by discretizing the flow channel. The effect of magnetic field on blood plasma in arteries was determined by creating a magnetic field gradient through the application of a varying strength of magnetic field on the flow. Heat transfer characteristics due to applied magnetic field and viscosity of blood was obtained by use of linear partial differential equations to determine varying temperature conditions in heat transfer characteristics. Numerical results for velocity profiles, magnetic profiles and temperature profiles were obtained to characterize blood plasma viscosity by use of various non-dimensional parameters. The results were graphically presented using MATLAB software. The results obtained helped in analyzing theoretically the effects of magnetic field and heat transfer in arterial plasma flow.

Four Chinese herbs Zhishi, Zhiqiao, Qingpi and Chenpi from Citrus genus were widely used for treating various cardiovascular and gastrointestinal diseases. Although many pharmacological functions of these herb decoctions can be clarified from the bioactivities of identified ingredients, some of them remain confusing. To clarify the reasons of those confusing functions, depending on the extended structure-activity relationships of cholinergic and anti-cholinergic agents, here a simple method for quickly discovering possible choline analogs was established using a specific TLC method, and then stachydrine and choline were first identified from these Citrus herb decoctions based on their NMR and HRMS data. After this, two TLCS methods were first established respectively for the quantitatively analyses of stachydrine and choline, and the contents of both two ingredients and synephrine in 39 samples were determined using the valid TLCS and HPLC methods, respectively. The results showed the contents of stachydrine were 2.4 times to those of synephrine in Zhiqiao while about 1/3 to 2/3 in Zhishi, Qingpi and Chenpi. Simultaneously, the contents of stachydrine, choline and synephrine in these herbs present similar changing trends along with the delay of harvest time. However, the contents of synephrine decrease most rapidly, while those of stachydrine decrease most slowly. Based on these above, comparing with the pharmacological activities and pharmacokinetics reported of stachydrine and synephrine, it indicated that stachydrine and synephrine can be considered as a pair of bioactive equilibrists, especially in the cardio-cerebrovascular protection from these citrus herbs. Simultaneously, it confirmed that stachydrine should play an important role in the pharmacological functions, especially in dual-directionally regulating the uterus and various beneficial effects on cardio-cerebrovascular system, kidney and liver, of these citrus herbs.

This article describes the Analytic Hierarchy Process (AHP) method which can be calculated by several methods. The AHP method is essential for the managerial decision-making to recognize which method is efficient for the calculation and to determine the proper order of criteria. In the article there are included methods that can be used in order to calculate the matrix in the AHP process for setting criteria such as Geometric mean, Arithmetic mean, Row sum of the adjusted the Saaty matrix, Reverse sums of the Saaty matrix columns and Row sums of the Saaty matrix. The paper is focused on the accuracy of the methods used. The results show that the most accurate method is the Saaty method, and the second most accurate method is the geometric mean in order to determine the ranking. This method is easier to use when the same order is achieved as in the Saaty method, followed by Geometric mean, which is favourable for fast and easy determination of alternatives using in the AHP process. The survey carried out among managers graduated from Universities and Colleges in Slovakia showed that the respondents considered the Saaty method as the most complex and also the most difficult method and the geometric mean average method the simplest method. 44% of respondents stated that they are capable to use a program to calculate the AHP. 46% of respondents said they had experience with some method related to the managerial decision-making process. 72% of managers regarded as important to manage some method for decision-making in their managerial position.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

The Simplified Spherical Harmonic (SPN) approximation was first introduced as a three-dimensional (3-D) extension of the plane-geometry Spherical Harmonic (PN) equations. A third order SPN (SP3) solver, recently implemented in the Nodal Expansion Method (NEM), has shown promising performance in the reactor core neutronics simulations. This work is focused on the development and implementation of the transport corrected interface and boundary conditions in NEM SP3 solver, following recent published work on the rigorous SPN theory for piecewise homogeneous regions. A streamlined procedure has been developed to generate the flux zero and second order/moment discontinuity factors (DFs) of the generalized equivalence theory to eliminate the error introduced by pin-wise homogenization. Moreover, several color set models with varying size and configuration are later explored for their capability of generating DFs that can produce results equivalent to that using the whole-core homogenization model for more practical implementations. The new developments are tested and demonstrated on the C5G7 benchmark. The results show that the transport corrected SP3 solver shows general improvements to power distribution prediction compared to the basic SP3 solver with no DFs or only zero order/moment DFs. The complete equivalent calculations using the DFs can almost reproduce transport solutions with high accuracy. The use of equivalent parameters from larger size color set models show better prediction in the whole-core calculations. By coupling different color set models DFs can offer the best accuracy at both eigenvalues and power distributions.

The analytical method for the calculation of the properties of a bolted connection established by the structural Eurocodes proposes the T-stub as a component for the characterization of the tension and compression zones in moment joints. In this article, a review of the state of the art on the T-stub component is developed, where the works developed since it was initially defined, and from the perspectives of formulation, experimentation and numerical simulation are summarized and discussed. Additionally, possible future lines of work are proposed.

The methods for constructing solutions to integro-differential equations of the Volterra type are considered. The equations are related to fractional conformable derivatives. Explicit solutions of homogeneous and inhomogeneous equations are constructed and a Cauchy-type problem is studied. It should be noted that the considered method is based on the construction of normalized systems of functions with respect to a differential operator of fractional order.

Missing observations constitute one of the most important issues in data analysis in applied research studies. The magnitude and their structure impact parameters estimation in the modeling with important consequences for decision-making. This study aims to evaluate the efficiency of imputation methods combined with the backpropagation algorithm in a nonlinear regression context. The evaluation is conducted through a simulation study including sample sizes (50, 100, 200, 300 and 400) with different missing data rates (10, 20, 30 40 and 50%) and three missingness mechanisms (MCAR, MAR and MNAR). Four imputation methods (Last Observation Carried Forward, Random Forest, Amelia and MICE) were used to impute datasets before making prediction with backpropagation. 3-MLP model was used by varying the activation functions (Logistic-Linear, Logistic-Exponential, TanH-Linear and TanH-Exponentiel), the number of nodes in the hidden layer (3 - 15) and the learning rate (20 - 70%). Analysis of the performance criteria (R2, r and RMSE) of the network revealed good performances when it is trained with TanH-Linear functions, 11 nodes in the hidden layer and a learning rate of 50%. MICE and Random Forest were the most appropriate for data imputation. These methods can support up to 50% of missing rate with an optimal sample size of 200.

The magnetic polarization tensor has a promising capability of determining the geometry and material properties of metallic samples. In this paper, a novel computation method is proposed to estimate the magnetic polarization tensors for the metallic samples using the boundary element method. In this method, the metallic sample is placed in a uniformly distributed magnetic field. Based on assumptions that the excitation frequency and/or the conductivity of the sample is very high, the metallic sample is regarded as a perfect electrical conductor (PEC). Therefore, the scattered field at a certain distance can be simulated. By utilising the boundary element method, the magnetic polarization tensor can be derived from the simulated scattered field. The theoretical calculation is presented and simulations and experiments have been carried out to validate the proposed method. The results from the simulation are matched with the analytical solution for the case of sphere samples. Moreover, there is a good agreement between the simulation results and the experimental results for the copper cylindrical samples.

This paper proposes a model to evaluate business projects to get into an incubator, allowing to rank them in order of selection priority. The model combines the Momentum method to build prospective scenarios and the Multiple Criteria Decision Making (MCDM) method TOPSIS-2N to rank the alternatives. Six business projects were evaluated to be incubated. The Momentum method made it possible for us to create an initial core of criteria for the evaluation of incubation projects. The TOPSIS-2N method supported the decision to choose the company to be incubated by ranking the alternatives in order of relevance. Our evaluation model has improved the existing models used by incubators. This model can be used and / or adapted by any incubator to evaluate the business projects to be incubated. The set of criteria for the evaluation of incubation projects is original and the use of prospective scenarios with a MCDM method to evaluate companies to be incubated does not exist in the literature.

This work focuses on the bifurcation behavior before chaos phenomenon happens. Traditional numerical method is unable to solve the unstable limit cycle of nonlinear system. One algorithm is introduced to solve the unstable one, which is based one of the continuation method is called DEPAR approach. Combined with analytic and numerical method, the two stable and symmetrical equilibrium solutions exist through Fork bifurcation and the unstable and symmetrical limit cycles exist through Hopf bifurcation of Lorenz system. With the continuation algorithm, the bifurcation behavior and its phase diagram is solved. The results demonstrate the unstable periodical solution is around the equilibrium solution, besides the trajectory into the unstable area cannot escape but only converge to the equilibrium solution.

In this paper, the definition of information entropy of Smoluchowski coagulation equation for Brownian motion is introduced based on coagulation probability. The expression of entropy is the function of geometric average particle volume and standard deviation with lognormal distribution assumption. The asymptotic solution with moment method shows that the entropy is a monotone increasing function of time, which is equivalence to the entropy based on particle size distribution. the result reveals that the present definition of entropy of Smoluchowski coagulation equation are inadequate because the particle average volume at equilibrium cannot be determined from the principle of maximum entropy. This provides a basis for further exploring the global properties of Smoluchowski coagulation equation.

This study used the sol–gel method to synthesize a non-halogenated hyperbranched flame retardant containing nitrogen, phosphorus and silicon, HBNPSi, which was then added to a polyurethane (PU) matrix to form an organic–inorganic hybrid material. Using 29Si nuclear magnetic resonance, energy-dispersive X-ray spectroscopy of P- and Si-mapping, scanning electron microscopy, and X-ray photoelectron spectroscopy, this study determined the organic and inorganic dispersity, morphology, and flame retardance mechanism of the hybrid material. The condensation density of the hybrid material PU/HBNPSi was found to be 74.4%. High condensation density indicates a dense network structure of the material. The P- and Si-mapping showed that adding inorganic additives in quantities of either 20% or 40% results in homogeneous dispersion of the inorganic fillers in the polymer matrix without agglomeration, indicating that the organic and inorganic phases had excellent compatibility. In the burning test, adding HBNPSi to PU resulted in the material passing the UL-94 standard at the V2 level, unlike the pristine PU, which did not meet the standard. The results demonstrated that after non-halogenated flame retardant was added to PU, the material’s flammability and dripping were lower, thereby proving that flame retardants containing elements such as nitrogen, phosphorus, and silicon exert an excellent flame retardant synergistic effect.

We investigate the impact of air quality and weather on the equity returns of the Shenzhen Exchange. To capture the air quality and weather effects, we use dummy variables created by employing a moving average and moving standard deviation. The important results are as follows. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative influence on the equity returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative impacts on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the weather effect of the abnormal temperature on the stock returns is greater in severe bearish market. Whereas the effect of the air pollution on the stock returns is greater in the bullish market. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analyzing these effects in a very volatile emerging market such as the Shenzhen stock market.

In order to overcome this problem our group designed a novel machine learning technique, multivariate linear method (MLM) which can capture convergent data from voxel-based morphometry, functional resting state and task-related neuroimaging and the relevant clinical measures. In this paper we report results from convergent cross-validation of biological signatures of disease in a sample of patients with schizophrenia as compared to depression. Our model provides evidence that the combination of the neuroimaging and clinical data in MLM analysis can inform the differential diagnosis in terms of incremental validity to reach 90 % accuracy of the prediction.

Cluster-based routing in Mobile Ad-Hoc Networks is considered one of the convenient methods of routing. The existence of Cluster Head (CH) in a group of nodes for data forwarding improves the performance of routing in terms of routing overhead and power consumption. In this paper, a clustering algorithm using hierarchical routing for mobile ad hoc networks is proposed. In the proposed method, first, clusters are formed by the FLOC clustering method with low overlapping. Then, according to the most important network criteria, including hop count, noise ratio, distance, remaining energy, and link expiration time, head clusters are selected based on the weighting algorithm. To transfer data in the proposed method, two types of communication are used, e.g., inter-cluster communication and intra-cluster communication in which the shortest path to the target cluster is selected. The proposed P-METHOD technique is based on hierarchy and clustering as well as using a weighted algorithm that reduces delay in data transmission on the network. Moreover, P-METHOD is evaluated here via extensive simulations carried out in NS-2. The simulation results indicate that the MANET network performance metrics are improved in terms of average throughput, Packet Delivery Ratio (PDR), delay, residual energy, and lifetime.

To investigate the effect of Polyvinylpyrrolidone (PVP) addition and consequently porosity, two different sets of membranes are manufactured, since PVP is a widely used poring agent which has an impact on the mechanical properties of the membrane material. The first set (PAN 1) includes PAN and the necessary solvent while the second set (PAN 2) is made of PAN and PVP. These membranes are put through several characterisation processes including tensile testing. The obtained data are used to model the static behaviour of the membranes with different geometries, but similar loading and boundary conditions that represent their operating conditions. This modelling process is undertaken by using finite element method. The main idea is to investigate how geometry affects the load-carrying capacity of the membranes. Alongside membrane modelling, their materials are modelled with representative elements with hexagonal and rectangular pore arrays (RE) to understand the impact of porosity on the mechanical properties. Exploring the results, the best geometry is found as the elliptic membrane with the aspect ratio 4 and the better RE as the hexagonal array which can predict the elastic properties with an approximate error of 12%.

As the aileron mass parameter and its position on the velocity and frequency of the flutter is an important problem in design of the aircraft wings, the optimization of the composite wing with an aileron is represented in this paper. Mass properties and its distribution have a great influence on the multi-disciplinary optimization procedure based on speed and frequency of flutter. At first, flutter speed was obtained with and without aileron, then aileron was mass-equilibrated and other studies were performed using the proposed method. It is deduced that changing the position and mass properties of the aileron the speed and frequency of the flutter changed. The position of the aileron was determined for better wing performance in flutter instability and minimizing the composite stress. In the present study, it has been attempted to model the aerodynamics of the problem under ultrasound with the panel method, and the structure has been modeled using finite element method and coupled with the aerodynamics. Using the p-k method, the equations are solved and the results are extracted.

We investigate the impact of air quality and weather on the stock market returns of the Shenzhen Exchange. To capture the air quality and weather effects, we apply dummy variables generated by applying a moving average and moving standard deviation. Our study provides several interesting results. First, in the whole sample period (2005–2019), we find that high air pollution and extremely high temperature have significant and negative effects on the Shenzhen stock returns. In the sub-period I (2005–2012), the 11-day model and 31-day model show that high air pollution have significant and negative effects on the Shenzhen stock returns. Second, the results of the quantile regression show that high air pollution have significant and negative effects during bullish market phase, and extremely high temperature have significant and negative effects during bearish market phase. This implies that the air quality and weather effects are asymmetric. Third, the more the Shenzhen stock returns drop, the greater the effect of the abnormal temperature is. Whereas, the more the Shenzhen stock returns increase, the greater the effect of the abnormal air quality is. Fourth, the least squares method underestimates the air quality and weather effects compared to the quantile regression method, suggesting that the quantile regression method is more suitable in analysing these effects in a very volatile emerging market such as the Shenzhen stock market.

The consumption of dairy products and the dairy industry is one of the main global agro-food sectors for size, economic importance and level of technology. Microbiological quality of pasteurized milk or other milk products is dependent on microbiological quality of raw milk. A variety of microbiological count methods is available for monitoring the hygienic quality of raw milk. Among them, the pour plate method is the official essay for counting the number of colony forming units in milk samples according to ISO 4833-1:2013. The aim of the present study is the validation of the Micro Biological Survey (MBS) method, against the reference plate count method, for the assessment of the microbiological quality of raw milk. This comparative study, performed in collaboration with the “Istituto Zooprofilattico Sperimentale del Lazio e della Toscana M. Aleandri” (IZSLT), demonstrates the accuracy of this alternative method for the determination of total viable bacterial count in cow’s raw milk. The results obtained with the MBS method highlighting its potential as a valid tool for reliable microbiological analysis in dairy industries.

One of essential procedure nowadays to analyze a dynamic process in Science and Engineering is Computational modeling. Most of dynamic processes are distributed parameter systems, i.e., systems with state variables depend on the number of independent variables (such as space and time) which are expressed by a set of Partial Differential Equations (PDEs). Lateral method of lines is a method which used for solving PDEs numerically by solving a set of boundary value problems sequentially. The aim is to report the development of PDE toolbox based on SCILAB. This paper provides users with a method that is very easy to understand in the applications related to dynamic process. The method uses a SCILAB template to develop numerical simulations in the new field. In this paper, a model of tropical fruit heat treatment for decimating insect is presented. The illustration will be given to show how the lateral method of line template works to solve the problem.

The paper focuses of the interaction between tungsten (W) wire and microwave field in carbon dioxide (CO2) atmosphere. Our experimental set-up uses a microwave plasma generator in order to generate the plasma from the metallic wires. The microwave plasma generator contain a cylindrical cavity - TM_011 propagation modes, commercial source (magnetron) having the 2.45 GHz frequency at 800 W microwave and power supply. In the focal point of the cylindrical cavity we have a high energy of the electromagnetic radiation. The metallic wires from this area will be vaporized and ionized having as effect CO2 dissociation. The electron temperature regarding metallic plasma produced was estimated using the ratio of atomic emission lines acquired by a high definition of the optical multichannel spectrometer. Determination of the CO2 dissociation quantity was estimated measuring of the carbon monoxide (CO) resulting of the CO2 dissociation process. We obtained a high electron temperature of the plasma and a strong dissociation of the CO2.

The purpose of this study was to detect mind-wandering experienced by pre-service teachers while learning video lecture on physics. The lecture was videotaped and consisted of a live lecture in a classroom. The lecture was about Gauss's law on physics. We investigated whether oculomotor data and eye movements could be used as a marker to indicate the learner’s mind-wandering. Each data was collected in a study in which 24 pre-service teachers (16 females and 8 males) reported self-caught mind-wandering while learning physics video lecture during30 minutes. A Tobii Pro Spectrum (sampling rate: 300Hz) was used to capture their eye-gaze during learning Gauss's law course video. After watching video lecture, we interviewed pre-service teachers about their mind-wandering experience. We first used the self-caught method to capture the mind-wandering timing of pre-service teachers while learning from video lectures. We detected more accurate mind-wandering segments by comparing fixation duration and saccade count. We investigated two types of oculomotor data (blink count, pupil size) and nine eye movements (average peak velocity of saccades; maximum peak velocity of saccades; standard deviation of peak velocity of saccades; average amplitude of saccades; maximum amplitude of saccades; total amplitude of saccades; saccade count/s; fixation duration; fixation dispersion). The result was that the blink count could not be used as a marker for mind-wandering during learning video lectures among them (oculomotor data and eye movements), unlike previous literatures. Based on the results of this study, we identified elements that can be used as mind-wandering markers while learning from video lectures that are similar to real classes, among the oculomotor data and eye movement mentioned in previous literatures. Also, we found that most participants focused on past thoughts and felt unpleasant after experiencing mind-wandering through interview analysis.

The aim of the research was a comprehensive evaluation of concrete using the EIPI method. In the evaluation the compressive strength of concrete and its durability properties represented by sorptivity and air permeability were taken into account. Since copper slag waste with increased natural radioactivity was used in the assessed concrete, additional evaluation was carried out taking into account the influence of natural radioactivity within the performance index. Also the reference concrete, which was made without the use of copper slag waste, was evaluated for comparative purposes. In order to make the evaluation as comprehensive as possible, the concrete made with the use of three types of cement was subjected to the assessment: CEM I, CEM II and CEM III. The results show that in both approaches the best result was achieved by concrete with CEM III cement. If natural radioactivity is not taken into account in the evaluation, the best result is obtained by concrete made with copper slag waste, and if radioactivity is considered, the best result is obtained with concrete without addition of the waste. It follows from the above that although natural radioactivity has a significant impact on the EIPI evaluation result, the decisive factor is still the type of cement.

Use of Machine Learning (ML) methodologies in optical communications has paved a new pathway. In this paper, firstly, we discuss the use of ML methodologies for reducing optical fiber nonlinearities, nonlinearity compensation, fault detection and optical performance monitoring. Then we present our recent work where we compare RL-SARSA and SVM based method with conventional method. The results show that RL-SARSA and SVM methods are successful candidates in mitigating the nonlinearities in proposed system as compared to conventional optical communication system.

We present an improved algorithm for fast calculation of the inverse square root for single-precision floating-point numbers. The algorithm is much more accurate than the famous fast inverse square root algorithm and has a similar computational cost. The presented modification concern Newton-Raphson corrections and can be applied when the distribution of these corrections is not symmetric (for instance, in our case they are always negative).

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

It is important for enterprises to decide their environmental policies after carefully examining their future paths based on the relationship between the environment and the economy. This study focused on Japanese minimum administrative divisions (municipalities) and attempted to quantify the annual environmental efficiency of production activities within each division according to the theory of life-cycle impact assessment (LCIA). This study leverages the assessment theory LIME2, which is an endpoint-type LCIA method developed in 2010 that integrates environmental loads for certain impact categories, such as global warming and land use into a simple indicator by monetary unit. First, annual environmental impact assessments were conducted for all Japanese municipalities based on statistical information that was reliable, verifiable, and comparable. Next, the environmental efficiency of productivity for each division was conceptualized by dividing the gross domestic product by the environmental damage amounts as calculated above. Assessment results for each municipality were placed on a map of Japan in order to visualize the regionality of each indicator. The findings revealed in this study will aid public administrators in their decision-making process with respect to environmental policies.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

Hardy Cross originally proposed a method for analysis of flow in networks of conduits or conductors in 1936. His method was the first really useful engineering method in the field of pipe network calculation. Only electrical analogs of hydraulic networks were used before the Hardy Cross method. A problem with the flow resistance versus the electrical resistance makes these electrical analog methods obsolete. The method by Hardy Cross is taught extensively at faculties and it still remains an important tool for analysis of looped pipe systems. Engineers today mostly use a modified Hardy Cross method which threats the whole looped network of pipes simultaneously (use of these methods without computers is practically impossible). A method from the Russian practice published during 1930s, which is similar to the Hardy Cross method, is described, too. Some notes from the life of Hardy Cross are also shown. Finally, an improved version of the Hardy Cross method, which significantly reduces number of iterations, is presented and discussed. Also we tested multi-point iterative methods which can be used as substitution for the Newton-Raphson approach used by Hardy Cross, but this approach didn’t reduce number of required iterations to reach the final balanced solution. Although, many new models have been developed since the time of Hardy Cross, main purpose of this paper is to illustrate the very beginning of modeling of gas and water pipe networks or ventilation systems.

1) Public health remains a tiny portion of the undergraduate pharmacy curriculum and the material is integrated into other modules. The objective of this study is to describe the UK undergraduate pharmacy curriculum, including its public health content; 2) Methods: A qualitative method (content analysis of websites) was used to describe the UK undergraduate pharmacy curriculum and teaching and learning policy. This involved selecting relevant concepts and then quantifying their presence and the relationships between them. The NVivo software was used to carry out ‘group queries’ and visualisation of results; 3) Results: Public health remains an optional module in the curricula of many UK schools of pharmacy. Several public health-related topics are often integrated into other modules, but UK undergraduate pharmacy curricula are still dominated by traditional pharmacy modules; and 4) Conclusions: Most of the curricula analysed were dominated by traditional pharmacy modules designed to enhance students' knowledge and skills. The skill set of UK pharmacy students with respect to macro-level public health activities needs to be improved in order to enhance pharmacists’ contribution to public health.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

Transient analysis of gas flow in pipeline was studied. Finite Element Method based on ANSYS FLOTRAN was used to account for changes in pressure, temperature and flow rate. Compressibility factor function of temperature and pressure was considered. For non-isothermal transient results, the pressure and the flowrate gave wave propagation as a result of slow transients created by demand condition at the outlet end of custody transfer. Results obtained were in agreement with the demand restrictions at the outlet end of custody transfer indicating that the predictions are accurate and reliable. The results demonstrated that the Finite Element Method gave accurate prediction of pressure, temperature and flowrate in transient gas studies. For steady state non-isothermal model, results showed that the magnitude of the average pressure drop was higher when pressure was predicted with constant compressibility factor, but the same average pressure drop was reduced when the pressure was predicted with variable compressibility factor, z. Since compressibility factor is a function of temperature and pressure, the above findings signifies that in the case when gas temperature does not stabilize, the prediction of pressure with isothermal model and constant compressibility factor will lead to significant errors.

Declining water supply is the main cause of rising water fee for agricultural use. Moreover, in non-technical irrigation, poor irrigation infrastructure exacerbates water scarcity. Thus, the purpose of this study is to identify farmer willingness to pay for non-technical irrigation and its determinants. Structured questionnaire was used to collect data from 100 farmers. Contingent valuation method was employed to elicit farmer WTP and multiple linear regression was used to find its determinants. The result shows that farmer average WTP is Rp 3,055,168 /ha/year. It accounts for 20 percent of total farmer revenue and almost 20 times fee for technical irrigation. Economic and technical variables are the significant determinants of WTP while social variables seem insignificant to WTP. This result indicates high economic value of water, and to improve irrigation management we recommend establishing irrigation infrastructure gradually by mobilizing farmer resources (capital and management) and strengthening WUA.

Maximum hardness and hardened depth are the responses of interest in relation to the laser hardening process. These values define heat treatment quality and have a direct impact on mechanical performance. This paper aims to develop models capable of predicting the shape of the hardness profile depending on laser process parameters for controlling laser hardening quality (LHQ), or rather the response values. An experimental study was conducted to highlight hardened profile sensitivity to process input parameters such as laser power (P_L), beam scanning speed (V_S) and initial hardness in the core (H_C). LHQ modeling was conducted by modeling attributes extracted from the hardness profile curve using two effective techniques based on the punctual and geometrical approaches. The process parameters with the most influence on the responses were laser power, beam velocity and initial hardness in the core. The obtained results demonstrate that the geometrical approach is more accurate and credible than the punctual approach according to performance assessment criteria.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

A heat pump with thermal storage system is a system that operates a heat pump during night-time using inexpensive electricity; during this time, the generated thermal energy is stored in a thermal storage tank. The stored thermal energy is used by the heat pump during daytime. Based on a model of a dual latent heat storage tank and a heat pump, this study conducts control simulations using both conventional and advanced methods for heating in a building. Conventional methods include the thermal storage priority method and the heat pump priority method, while advanced approaches include the region control method and the dynamic programming method. The heating load required for an office building is identified using TRNSYS, used for simulations of various control methods. The thermal storage priority method shows a low coefficient of performance (COP), while the heat pump priority method leads to high electricity costs due to the low use of thermal storage. In contrast, electricity costs are lower for the region control method, which operates using the optimal part load ratio of the heat pump, and for dynamic programming, which operates the system by following the minimum cost path. According to simulation results for the winter season, the electricity costs using the dynamic programming method are 17% and 9% lower than those of the heat pump priority and thermal storage priority methods, respectively. The region control method shows results similar to the dynamic programming method with respect to electricity costs. In conclusion, advanced control methods are proven to have advantages over conventional methods in terms of power consumption and electricity costs.

As a procedure deriving UH (unit hydrograph), the root selection method necessitates only storm runoff data. However, this method must deal with the uncertainty related to the noise fluctuation of runoff ordinates and derive one optimal UH from many storms. This study proposes a procedure that applies the Savitzky-Golay filter to smooth the noise fluctuation of the runoff ordinates and uses the linear combination of UHs from individual storms to derive an optimal UH. The proposed method is applied to the storms of the Nenagh River basin in Ireland. The applicability of the Savitzky-Golay filter for smoothing the noise fluctuation of storm runoffs is examined by means of the Nash-Sutcliffe efficiency index. Furthermore, the root selection method is extended to also estimate IUHs. The results show that the adoption of the Savitzky-Golay filter improves the applicability of the root selection method and that the optimal UH predicts accurately the time-to-peak and peak discharge.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.

We investigate entropy generation in unsteady three-dimensional axisymmetric MHD nanofluid flow over a non-linearly stretching sheet. The flow is subject to thermal radiation and a chemical reaction. The conservation equations were solved using the spectral quasi-linearization method. The novelty of the work is in the study of entropy generation in three-dimensional axisymmetric MHD nanofluid and the choice of the spectral quasilinearization method as the solution method. The effects of Brownian motion and thermophoresis are also taken into account when the nanofluid particle volume fraction on the boundary in passively controlled. The results show that as the Hartman number increases, both the Nusselt number and the Sherwood number decrease whereas the skin friction increases. It is further shown that an increase in the thermal radiation parameter corresponds to a decrease in the Nusselt number. Moreover, entropy generation increases with the physical parameters.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in some sections we present concerning numerical examples and the respective softwares.

One of the important air pollutants is ammonia, which is mainly emitted from the agriculture sector. This sector is responsible for over 81% of global ammonia emissions. The main threat related to ammonia emissions is water eutrophication and soil acidification. The aim of the research was a preliminary assessment of the implementation status of methods for reducing ammonia emissions on farms and to learn the views and awareness of agricultural producers on reducing emissions of pollutants into the air. The research was conducted using a survey questionnaire that was made available to farmers in various ways. Based on the results of pilot surveys, it can be concluded that farmers have general knowledge of environmental protection and generally agree that people have an impact on the state of the environment. Low-emission practices to reduce ammonia emissions from agricultural sources are not widely used. The best situation is regarding reduction practices in the storage of natural fertilizers and the use of low-emission fertilizer application techniques. Some reduction activities are not obligatory, therefore it is difficult to determine the scope of application of these practices. Therefore, such periodic research will allow monitoring the activity of agricultural producers in implementing reduction methods.

Sick sinus syndrome (SSS) is a disease of sinus rhythm abnormalities. This study aimed to establish an SSS model by injecting 3% NaOH into the jugular vein(JV). Sprague-Dawley rats were randomly divided into sham, 3% NaOH, and 10% NaOH groups. Anesthetized rats underwent electrocardiogram recording before right JV exposure. Rats in the experimental groups received NaOH injections at 0.01 ml/s, while the sham group did not. Model success was evaluated after one hour. Heart rate(HR) and rhythm were documented at 1 hour, 1 week, and 2 weeks post-molding, including HE staining, membrane ion transcription and expression, and calcium ion content test. In the 3% NaOH group, the model establishment rate was 87%, and the mortality rate was 13%, whereas in the 10% NaOH group, they were 57% and 43% respectively (P < 0.01). The HR of the 3% NaOH group decreased at multiple time points post-molding (P < 0.001), presenting as arrhythmias such as sinus bradycardia. The JV sustained less damage, with necrosis of P cells, changes in membrane ion channels, and reduced calcium ion distribution. In conclusion, JV injection of 3% NaOH can establish the SSS model and benefit animals.

Wireline Formation Testing is an important technique in the oil field of exploration and development. Not only it can make real fluid samples of the formation directly obtained to know exactly oil existed in formation or not; but it can also show flowing pressure change to see the production capacity of the formation. So it is important measurement for formation evaluation during the drilling process and supports for activities of the exploration and development in the oil field. A numerical simulation model in this article is researched and established based on the Finite Volume Method with considering the influence of sensitive parameters such as reservoir heterogeneity, probe suction area, and mud-filtrate invasion depth during the drilling. The model is capable to design and evaluate for formation fluid sampling operations with calculating hydrocarbon content and flowing pressure. Furthermore, through case application, the performance and effect in the process of Wireline Formation Testing was demonstrated. The results indicate that this technology can be served as an effective auxiliary tool for fluid sampling operations with the function of optimizing fluid sampling measures. It can improve the accuracy of predicting indicators such as hydrocarbon content and breakthrough time during the sampling process. This study provides important backups and technical guidance for professionals in geological exploration and oilfield development.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

Nonlocal theories are gaining prominence because they can solve problems which lead to unphysical conclusions in standard models. This study presents a novel fractional boundary element method (BEM) solution for nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. This broad BEM solution combines two solutions: anisotropic fibrous polymer nanomaterials problem solution and nonlinear nonlocal thermoelasticity problem solution. The nonlinear nonlocal thermoelasticity problem solution divides the displacement field into complementary component and particular component. The overall displacement is generated using the boundary element technique, which is the solution to a Navier type problem, while the particular displacement is derived using local radial point. The New Modified Shift-Splitting (NMSS) approach, which reduces memory and processing time requirements, was used to solve linear systems created by BEM. Figures demonstrate the numerical findings, which show the effects of fractional and graded parameters on the thermal stresses of nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. The numerical results indicate the consistency and efficiency of the proposed methodology.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

The circular supply chain was applied to many industries in the past studies, whereas the rubber recycling industry has not been explored in detail yet. Therefore, this study indentified the key factors of the circular supply chain used in remanufactured products, thereby perfecting its framework. This study put forward 5 aspects and 19 criteria for reference, so that companies in the rubber recycling industry are able to clearly know the direction of implementation when con-structing the circular supply chain for remanufactured products. This study integrated expert opinions with the fuzzy Delphi method and the fuzzy decision making trial and evaluation laboratory proposed key factors, and performed the ranking of importance. The results have displayed that key aspects include the circular business model (A3), increasing the value of resources in the supply chain (A4), and risk management of the circular supply chain (A2). The factors that the rubber recycling industry needs to pay attention to are: optimizing the production process (C2), sharing data in the product lifecycle (C4), effectively tracking and recycling products (C5), redesigning remanufactured products (C13), enhancing resource efficiency (C16), and identifying waste composition and separating materials (C14) . Based on the abovementioned, we had a discussion in this study.

Homotopy perturbation and analysis methods have been widely used to obtain both approximate and exact so- lutions to nonlinear problems. In general, these two methods are based on the Taylor series with respect to an embedding parameter. Many researchers have compared the two methods and raised more concerns on the homo- topy perturbation method (HPM) because the homotopy analysis method (HAM) contains a convergence-control parameter ~: For this reason, in this article, a more general form of HPM is introduced as the -homotopy per- turbation method (-HPM), which contains a control parameter : The introduction of parameter  in this new modi cation gives a better way to adjust and control the convergence region and the rate of the series solution. We con rm through the given examples in this study that the HPM is a special case of the -HPM. The error and convergence analysis of this proposed method are also presented

Digital twin, an innovative technology propelled by data and models, plays a seminal role in the digital transformation and intelligent upgrade of ships. This study introduces a digital twin methodology for real-time monitoring of ship structure deformation fields, based on finite discrete strain data, and a visualization tool framework is developed using virtual reality technology. First, the inverse Finite Element Method (iFEM) is employed to derive the deformation field of the ship structure in real time via sensor strain data. Secondly, the deformation field data obtained based on the iFEM algorithm is converted into general visualization data conducive to interpretation within VR applications. Lastly, a digital twin software tool is built to enable synchronous response and interaction between the virtual scene and the physical scene, directly superposing particular virtual objects (data acquired by sensors, CAD virtual models, and deformation field cloud images) onto the physical scene in real-time. The digital twin tool embodies a virtual reality visualization system framework integrating physical data measurement, reconstruction, analysis, expression, storage, rendering and interaction of deformation field data. Through practical application, the flexibility, effectiveness and compatibility of the developed prototype tool are verified. According to the results, the system can enhance the efficiency of scientific communication, model validation, and interdisciplinary sharing during the analysis and evaluation of mechanical properties of ship structures.

This study investigates effective strategies for second language education in primary schools, analyzing the efficacy of immersive and interactive methods, digital literacy tools, and mixed-method approaches. The findings reveal significant improvements in language proficiency and student engagement through these methodologies, with immersive and interactive strategies showing substantial benefits in oral proficiency and engagement, digital tools enhancing accessibility and engagement, and mixed-method approaches yielding the highest overall effectiveness. The study underscores the importance of a balanced, flexible approach to language education, integrating traditional and modern methods to cater to diverse learner needs. These strategies not only advance linguistic skills but also contribute to the broader cognitive and emotional development of young learners, emphasizing the critical role of effective language education in preparing students for a globalized world.

Bipyridine and its related compounds are starting materials or precursors for a variety of valuable substances, such as biologically active molecules, ligands for catalysts, photosensitizers, viologens, and supramolecular architectures. Therefore, it is important to classify the synthesis methods and know their characteristics. Representative examples include the methods using homo- and heterocoupling of pyridine derivatives in the presence of catalyst. Because bipyridine compounds have a high ability to coordinate with metal centers, a decrease in catalytic activity and yield is often observed in the reaction system. To address this issue, the review provides insight into recent advances in bipyridine synthesis using metal complexes under both homogeneous and heterogeneous conditions. Moreover, the review also sheds light on strategies for bipyridine synthesis involving sulfur and phosphorous compounds. These alternative pathways offer promising avenues for overcoming challenges associated with traditional-catalyzed methods, providing a more comprehensive understanding of the synthesis landscape.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

Anastomosing rivers are wetland systems with multiple channels, and there are many constraints limiting in-situ observations of their hydrodynamics. Therefore, there are few reports on the hydrodynamic data of such rivers. In order to obtain the hydrodynamic parameters of the river channels without hydrological observations in the anastomosing rivers, this study proposes an expression method namely expression of channel morphological parameters (ECMP) for hydrodynamic calculations. The calculation formula of the ECMP method based on the shape factor, scale factor, and gradient factor of the flow cross-section as independent variables. This method can be used to calculate the average velocity, discharge, specific stream power, gross stream power and other hydrodynamic parameters of the flow cross-section at different water levels, only requiring the measurement of morphological parameters such as the average depth, width-depth ratio, and gradient of the flow (channel) cross-section. The applicability of the ECMP method was verified using measured hydrological data. The results show that the ECMP method is a practical calculation method with high computational accuracy and convenient application for calculating river hydrodynamic parameters. It has great application value in study on fluvial geomorphology and hydrodynamics, as well as in the reconstruction of ancient river hydrology and hydrodynamics.

This article describes the choice of an optimization algorithm for solving problems and the optimal design of an unmanned aerial vehicle propeller. To solve the problem using evolutionary algorithms, it was transformed into an unconstrained optimization problem using a penalty function. The airfoil contours were constructed using a Bezier curve. Design variables were divided into two types: those that describe in general terms the propeller geometry or operation, such as propeller diameter, number of blades, and rev/min; and those that vary with propeller radius, such as chord length, effective airfoil angle, and airfoil geometry. The objective function is the calculation of the propeller power required to achieve a given thrust. The differential evolution algorithm was used to solve this problem.

Employing low tensor rank decompositions in image inpainting has attracted increasing attention. This paper exploits a novel tensor-augmentation schemes to transform an image (a low-order tensor) to a higher-order tensor without changing the total number of pixels. The developed augmentation schemes enhance the low-rankness of an image under three tensor decompositions: matrix SVD, tensor train (TT) decomposition, and tensor singular value decomposition (t-SVD). By exploiting the schemes, we solve the image inpainting problem with three low-rank con-strained models which use the matrix rank, TT rank, and tubal rank as constrained priors re-spectively. The tensor tubal rank and tensor train multi-rank are developed from t-SVD and TT decomposition respectively. We exploit efficient ADMM algorithms for solving the three models. Experimental results demonstrate that our methods are effective for image inpainting and supe-rior to numerous close methods.

The intensification of conflicts associated with the use of water in the transition region of the Cerrado and Amazon biomes caused by population and economic growth, combined with the interest in generating energy from hydroelectric plants, raise the need to quantify the surface water availability of rivers contributing with different drainage areas. The present study estimated and compared loco measurements of liquid flow (QL) and depth of rivers in the Teles Pires river basin by reference methods (MLN-7 hydrometric windlass and metal rod/winch) and by Acoustic Current Profiler by Doppler Effect (ADCP RiverRay), in addition, evaluated the total measurement time underestimation uncertainty by ADCP. Field measurements were carried out at monthly intervals between March 2020 and October 2021, seeking to represent the water seasonality and depth and QL variations in the cross-sections of the Caiabi 1 and 2, Celeste, Preto and Renato rivers. The evaluated rivers had a net flow between 3.48 and 60.78 m3 s-1 by the windlass and between 2.66 and 54.30 m3 s-1 by the ADCP, while the depths obtained were from 0.17 to 6.34 m by the rod/winch and from 0.65 to 6.20 m by the ADCP. The methods resulted in similar measurements of net flow and depth in each of the cross-sections, and the statistical performance of the linear regression model was satisfactory with a Willmott concordance index of 0.9977 and 0.9819 for estimates of QL and of the depth of the cross-sections, respectively. The ADCP accurately measured net discharge and depth in shallow (up to 6.5 m) cross-sections of Teles Pires River in relative to the reference method. Determining the total measurement time and pairs of transects to obtain accurate QL by ADCP depends on the hydraulic characteristics of the watercourses.

Purpose: The rapid development of technological innovations is causing major transformations in organisations. These changes are facilitating the transition of organisations from traditional to digital cultures and are influencing the positioning and even the survival of many of them. Higher Education Institutions are no exception. This article aims to understand the main factors that facilitate and drive this transformation from the point of view of their external stakeholders. Design/methodology/approach - Due to the complexity of the study, the case study method has been used as an appropriate methodology. Findings - As the results of the study show, the use of new agile methodologies, the development of continuous improvement processes, the automation of tasks with the use of new technologies, data-driven decision making, and the management of new digital talent are enablers. Research limitations/implications - Further research could conduct similar analyses with other stakeholders, to achieve a complete management model. Practical implications - The case study allows researchers to learn from practitioners and business leaders, while providing a theoretical model that can help other managers in the process of transforming their organisations. Originality/value - The main contribution of this study has been to apply the study to a specific Higher Education Institution.

In recent years, the Chinese government pays more and more attention to agricultural development and ecological protection. While improving the cultivated land green use efficiency(CLGUE) is the key to promote the sustainable development of agriculture. This study aims to study the current situation and influencing factors of agricultural production from the perspective of green utilization efficiency of cultivated land. It takes 39 cities in the upper, middle and lower reaches of the Yangtze River basin in China as an example. The CLGUE values in those 39 cities from 2011 to 2020 were specifically measured, using the Super-SBM model, kernel density estimation and geographic detector method. Their temporal and spatial heterogeneity was described, and the influencing factors were detected at both single and interactive levels. The results showed that: （1）From 2011 to 2020, the green utilization efficiency value of cultivated land in the Yangtze River Basin showed an upward trend on the whole; （2）There is a clear spatial heterogeneity the CLGUE values in the Yangtze River Basin cities, as shown by: downstream region > midstream region > upstream region; (3) Cultivated land resource endowment, socioeconomic development, and agricultural production technology are important factors affecting the variability of CLGUE values. However, there are some differences in the degree and direction of influence of different influencing factors on different sample subgroups.

Cattle slurry is an important nitrogen source for maize on dairy farms. Slurry injection is an effective measure to reduce ammonia emissions after field application, but with higher risk of nitrous oxide emission than surface application. This study compared soil mineral nitrogen dynamics and nitrous oxide emissions with two ways of application. First, traditional injection at 25 cm spacing between rows followed by ploughing (called “non-placed slurry”), and second, injection using a new so-called goosefoot slurry injector that placed the slurry in ploughed soil as a c. 30 cm broad band at 10 cm depth below maize crop rows with 75 cm spacing (named “placed slurry”). Furthermore, the effect of treating slurry with the nitrification inhibitor 3,4-dimethylpyrazole phosphate (DMPP) in Vizura® was tested with both application methods. The field experiment was conducted on a sandy loam soil in a temperate climate. Both nitrous oxide emissions, and the dynamics of soil mineral nitrogen, were monitored for eight weeks after slurry application and seeding of maize using static chambers. The level of nitrous oxide emissions was higher with non-placed compared to placed slurry, mainly due to higher emissions during the first four weeks. That might be due to higher rates of nitrification rate and in turn stimulation of denitrification process. In both placed and non-placed slurry treatments, Vizura® caused higher soil ammonium concentrations and lower nitrate concentrations, particularly from 3 to 8 weeks after slurry application. The final level of soil nitrate was similar with and without the nitrification inhibitor, but higher with placed compared to non-placed slurry. Adding Vizura® to non-placed slurry reduced nitrous oxide emissions by 70 % when compared to placed slurry. Surprisingly, there was a non-significant trend towards higher cumulative emissions from placed slurry with the nitrification inhibitor compared to untreated slurry, which were due to higher emissions in the last part of the monitoring period (5-7 weeks after slurry application). Possibly degradation of the nitrification inhibitor, and nitrification activity inside the slurry band as the soil dried, promoted nitrous oxide emissions by this time. In summary, placement of untreated slurry in a broad band under maize seeds reduced nitrous oxide emissions compared to non-placed slurry with more soil contact. A comparable reduction was achieved by adding a nitrification inhibitor to non-placed slurry. The pattern of nitrous oxide emissions from placed slurry treated with the inhibitor was complex and requires more investigation.

This paper evaluates norms and assesses the level of knowledge in air conditioning project management within the construction industry. A total of 25 questions were distributed to multiple candidates, who were filtered based on pre-established inclusion and exclusion criteria. Thirty-nine candidates were ultimately approved to participate in the survey. The questions were designed to address five hypotheses, with each set of five questions corresponding to one hypothesis. The results were obtained after pre-processing the data using Matlab software. The data was pre-processed using Matlab software, and the results were analyzed using the Delphi method. The analysis revealed that only two hypotheses were approved: No matter whether there are nationalized safety rules or not, the impact of data sciences and smart technologies, including air conditioning management systems, is critical for human life in the building business.

In the present protocol, we determined the presence and concentrations of bisphenol A (BPA) spiked in surface water samples using EEM fluorescence spectroscopy in conjunction with modelling using partial least squares (PLS) and parallel factor (PARAFAC). PARAFAC modelling of the EEM fluorescence data obtained from surface water samples contaminated with BPA unraveled four fluorophores including BPA. The best outcomes for BPA concentration (R2 = 0:996; Standard deviation to prediction error's root mean square ratio (RPD) = 3.41; and a Pearson's r value of 0.998). With these values of R2 and Pearson's r, the PLS model showed a strong correlation between the predicted and measured BPA concentrations. The detection and quantification limits of the methods were 3.512 and 11.708 micro molar (µM), respectively. In conclusion, BPA can be precisely detected and its concentration in surface water predicted using the PARAFAC and PLS models developed in this study and fluorescence EEM data collected from BPA-contaminated water. It is necessary to spatially relate surface water contamination data with other datasets in order to connect drinking water quality issues with health, environmental restoration, and environmental justice concerns.

Anti-microbial drugs and coccidiostat compounds are commonly used in poultry farming. These compounds are subsequently excreted and released into the environment via broiler litter (BL) and can re-enter the food chain as fertilizer and/or animal feed. Residues of such drugs can encourage the appearance of antibiotic-resistant bacteria (ARB), as well as toxicity, when found in animal feed. The aim of this study was to develop a multi-residue analytic method for assessing 30 an-ti-microbial drugs and coccidiostats associated with BL and investigate the effects of stacking treatment on anti-microbial and coccidiostat residue degradation in BL used for ruminant feed at the lab-scale. Today, most analytical methods used to identify and quantitate these drug residues are traditional, and may be specific to some antimicrobials. All call for lengthy sample preparation and may present limitations in assessing broiler litter. Such conventional mul-ti-anti-microbial/coccidiostat residue detection assays employ liquid-liquid extraction (LLE) and solid phase extraction (SPE) for sample purification. In our research, LLE and SPE were replaced by Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) clean-up steps for 30 an-ti-microbials and coccidiostats used in broiler farming and detection by liquid chromatography mass spectrometry (LC/MS/ MS). Using this method, recoveries were 70-120%, with the exception of norfloxacin and narasin, which showed recoveries of 67 and 68%, respectively. This analytical meth-od results show that eight samples were not detected in 42 samples, while in 34 samples, one or more drugs were present. Eighteen anti-microbial and coccidiostat residues were detected dur-ing one year sample collaction. The most frequently detected residues were narasin, nicarbazin, monensin, robenidine, oxytetracycline, chlortetracycline, norfloxacin and sulfachloropyridazine, seen at levels from 0.4 to 8.9 mg•kg-1 (ppm). Nineteen anti-microbials and one coccidiostat were degraded to 95% by the stacking treatment. However, tilmicosin and eight coccidiostats persisted in litter (26-100%). The use of antimicrobials and coccidiostats in animal farming is of paramount concern with respect to human, animal and environmental contamination issues and as a source of resistant pathogenic bacteria. Still, most farmers use BL as ruminant feed and fertilizer without processing. Even though the effects of the stacking treatments on degradation of antimicrobials were significantly high, the degradation of coccidiostats and tilmicosin was limited. Clearly, BL should be treated and supervised before use as feed supplement or for land application. Hence, the present method, designed to support these goals, was optimized in terms of sensitivity and se-lectivity for the analytes addressed.

A class of controlled plants, whose dynamics is governed by a vector system of ordinary differential equations with a partially known right-hand side, is considered. The state variables and their velocities are assumed to be measurable. The aim is to design a controller which minimizes a loss function under certain constraints which arguments is the current state of the controlled plant. The designed control action is admitted to be a function of the current sub-gradient only, which supposed to be measurable on-line. The control design is based on ASG (Average Sub-Gradient method) — version of Integral Sliding Mode (ISM) concept, aimed to minimize on average a given convex (not obligatory strongly convex) cost function of the current state under a set of given constraints. An optimization type algorithm is developed and analyzed using ideas of SDM technique. The main results consist in proving the reachability of the "desired regime" (nonstationary analogue of sliding surface) from the beginning of the process and obtaining an explicit upper bound for the averaged loss function decrement, that is, the averaged in time functional convergence is proven and the rate of such convergence is estimated.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Rare-earth tetraborides RB4 are of great interest due to the occurrence of geometric magnetic frustration and corresponding unusual magnetic properties. While the Gd3+ spins in GdB4 align along the ab plane, Er3+ spins in the isomorphic ErB4 are confined to the c–axis. The magnetization in the latter exhibits a plateau at the midpoint of the saturation magnetization. Therefore, solid solutions of (Gd, Er)B4 provide an excellent playground for exploring the intricate magnetic behavior in these compounds. Single crystals of Gd(1-x)Erx B4 (x = 0, 0.2, and 0.4) were grown in aluminum flux. X-ray diffraction scans revealed single phase materials, and a drop in the unit cell volume with increasing Er content, suggesting the partial substitution of Er at the Gd sites. Heat capacity measurements indicated a systematic decrease of the Néel temperature (TN) with increasing Er content. The effective magnetic moment determined from the magnetization measurement agreed with the calculated free-ion values for Gd3+ and Er3+, providing further evidence for the successful substitution of Er for Gd. The partial substitution resulted in an anomalous ferromagnetic phase below TN, exhibiting significant anisotropy, predominantly along the c-axis. This intriguing behavior merits further studies of the magnetism in the Gd(1-x)ErxB4 borides.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

The aim of this paper is to optimize thickness variation function of simply supported and cantilever beams, in terms of maximizing gaps between chosen neighboring frequencies and analyze obtained results. The optimization results are examined in terms of achieving the objective function (related to eigenproblem), but also in terms of their dynamics stiffness (forced vibrations excited by point harmonic load). In the optimization process, a Genetic Algorithm was used. Problems related to structural dynamics were solved by FEM implementation into the algorithm. Sample results were presented, and the developed algorithm was analyzed in terms of result convergence by examining several variable parameters. The authors demonstrated the validity of applying the described optimization tool to the presented problems. Conclusions were drawn regarding the correlation between stiffness and mass distribution in the optimized beams and the natural frequency modes in terms of which they were optimized.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Vegetation identification using remote sensing is essential for understanding terrestrial ecosystems and monitoring climate change. This technology by providing high-resolution images of the Earth's surface from satellites, aircraft, and drones has revolutionized the way scientists study and un-derstand vegetation patterns, providing information on the distribution, structure, and health of plant communities in different regions and biomes. However, identifying vegetation in multi and hyperspectral images remains a difficult, time-consuming, and costly process. Traditional methods for vegetation mapping involve the in-terpretation of spectral indices such as the Normalized Difference Vegetation Index (NDVI), alt-hough they often suffer from limitations such as manual interpretation and limited spatial resolution of satellite images. Furthermore, machine learning techniques, artificial neural networks, decision trees, support vector machines, and random forests have shown promising results in identifying and classifying vegetation cover from hyperspectral images. However, due to the need for per-son-nel with specialized expertise, their application on a large scale is still challenging. On the other hand, correlation methods between curves have emerged as powerful and simplified tool for comparing spectral signatures of hyperspectral image pixels and efficiently classifying vegetation in a study area. Pearson's correlation coefficient and spectral angle mapper are among the most common correlation methods used in vegetation mapping. These correlation methods, among many others available, offer an easily implemented and computationally efficient approach, making them particularly useful for applications in developing countries or regions with limited resources. In this article, a comparative study of correlation/distance metrics was conducted for the detection of vegetation pixels in hyperspectral images. The study allowed for the comparison of five distance and/or correlation metrics: direct correlation, cosine similarity, normalized Euclidean distance, Bray-Curtis’s distance, and Pearson correlation. The two metrics that yielded the best accuracy results in vegetation pixel detection were direct correlation and Pearson correlation. Based on the selected methods, a vegetation detection algorithm was implemented and validated on a hyper-spectral image of the Manga neighborhood in Cartagena de Indias, Colombia. The spectral library was utilized for image processing, while the numpy and scipy libraries in the Python programming language were used for the mathematical calculation of correlations. Both the study's approach and the implemented algorithm aim to serve as a reference for conducting detection studies of various material types in hyperspectral images using open-access programming platforms.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

There is an overall scientific consensus that public space and, mainly, space with a high ecological index – most notably experienced in green areas – positively affects individual and collective well-being and urban dwellers’ physical and mental health. However, the ‘reality check’ indicates difficulties in translating the assumed benefits of green space into implementable interventions in urban environments. To examine such an ‘implementation gap’ on the case of Zurich seems valid, given that the ‘green urban agenda’ debate has been embedded in numerous Swiss policies (from the federal to the municipal levels). In narrow terms, the research first focuses on Zurich’s district 9 consisting of two neighborhoods (Altstetten and Albisrieden) – the area under ongoing densification yet with a variety of green spaces, to then elucidate four green space clusters and their 400-meter catchment areas in the mentioned district. The mixed-method approach has been applied at three analytical levels: 1) documentary analysis of multi-scale national policy toolkits, to identify the critical tenets associated with the ‘green urban agenda’, 2) assessment of green spaces in Zurich’s district 9 based on online available quantitative data and on-site observation, to determine their provision, types, size and mutual connectivity, and 3) analysis of four green space clusters within the mentioned district through on-site observation, to identify green space attributes and main activities. Through critical mutual examination of the identified ‘green urban agenda’ principles in the national policies, on the one hand, and green space attributes, on the other, the research findings reveal the extent of the convergence and/or divergence between the ‘green urban agenda’ policy trends and their implementation in practice.

Distributed electric propulsion technology has great potential and advantage in the development of drones. In this paper, to study the slipstream effect of distributed propeller, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by genetic algorithm. The analysis results showed that lift of the wing will be larger when the propellers are higher than the wing. When the relative height between the propeller and the wing is zero, the drag is the lowest. The influence of disk diameter on the slipstream is that the larger the diameter is, the higher the lift force and the drag force are. The slipstream effect of the optimized propeller distribution improves the lift-drag ratio of the wing, by 108.5% in the initial lift-drag ratio.

The analysis concerned a thin-walled plate with a circular central hole made of CFRP (Carbon Fiber Reinforced Polymer) material. The test object was subjected to a tensile test to investigate the cracking mechanism of the composite structure. The tests were performed using two independent test methods experimentally and numerically. In the experiment, the force was recorded as a function of elongation of the tensile plate and the elongation of the plate was investigated using an Aramis non-contact optical measurement system. As part of the numerical analysis, an FEM model adequate to the experimental conditions was performed in the Abaqus system. The fracture process was modeled using the extended finite element method XFEM. This approach enabled the structure of the composite to be investigated over the full range of tensile loading. The behaviour of the circular hole plate before the damage symptoms was investigated, the damage initiation force was determined, then the initial cracking and delamination of the layers were analysed, as well as the crack propagation process leading to the complete failure of the composite structure (cracking of all laminate layers).

Natural ventilation in a building is an effective way to achieve acceptable indoor air quality. Ventilation dilutes contaminants such as bio-effluents generated by occupants, substances emitted from building materials, and water vapor generated by occupants' activities. In a building that requires heating and cooling, adequate ventilation is crucial to minimize energy consumption while maintaining healthy indoor air quality. However, measuring the actual magnitude of the ventilation rate, including infiltration through the building envelope and airflow through building openings, is not always feasible. In this study, the occupant-generated carbon dioxide (CO2) tracer gas decay method was applied to estimate the ventilation rates in an office room in Seoul, South Korea, from summer to winter. Using the method, real-time ventilation rates can be calculated by monitoring indoor and outdoor CO2 concentrations without injecting a tracer gas. 145mm-diameter circular openings on the fixed glass were used for natural ventilation in the test room. As a result, firstly, the indoor CO2 concentrations were used as an indicator to evaluate how much the indoor air quality deteriorated when all the windows were closed in an occupied office room compared to international standards for indoor air quality. Moreover, we found out the estimated ventilation rates varied depending on various environmental conditions, even with the same openings for natural ventilation. Considering the indoor and outdoor temperature differences and outdoor wind speeds as the main factors influencing the ventilation rates, we analyzed how they affected the ventilation rates in different seasons of South Korea. When the wind speeds were calm, the temperature difference played as a factor that influences the estimated ventilation rates. On the other hands, when the temperature differences were low, the wind speed was the primary factor. This study raises awareness about the risk of poor indoor air quality in office rooms that could lead to health problems or unpleasant working environments. This study presents an example of estimating the ventilation rates in an existing building. In the same way, the ventilation rate in an existing building can be simply estimated while using the building as usual, and appropriate ventilation strategies for the building can be determined to maintain desired indoor air quality.

The ordered Ca3TaGa3Si2O14 and disordered La3Ga5SiO14 crystals of the lantangallium silicate family were grown by the Czochralski method. The independent coefficients of thermal expansion of crystals αc and αa were determined by X-ray powder diffraction based on the analysis of X-ray diffraction spectra measured in the temperature range of 25÷1000°C. It is shown that in the temperature range of 25÷800°C the thermal expansion coefficients are linear. At temperatures above 800°C there is a nonlinear character of the thermal expansion coefficients associated with a decrease in the Ga content in the crystal lattice of the lantangallium silicate family crystals.

Quantum computing has attracted significant interest in the optimization community because it potentially can solve classes of optimization problems faster than conventional supercomputers. Several researchers proposed quantum computing methods, especially Quantum Interior Point Methods (QIPMs), to solve convex optimization problems, such as Linear Optimization, Semidefinite Optimization, and Second-order Cone Optimization problems. Most of them have applied a Quantum Linear System Algorithm at each iteration to compute a Newton step. However, using quantum linear solvers in QIPMs comes with many challenges, such as having ill-conditioned systems and the considerable error of quantum solvers. This paper investigates how one can efficiently use quantum linear solvers in QIPMs. Accordingly, an Inexact Infeasible Quantum Interior Point Method is developed to solve linear optimization problems. We also discuss how we can get an exact solution by Iterative Refinement without excessive time of quantum solvers. Finally, computational results with a QISKIT implementation of our QIPM using quantum simulators are analyzed.

Microstructure evolution in metal additive manufacturing (AM) is a complex multi-physics and multi-scale problem. Understanding the impact of AM process conditions on the microstructure evolution and the resulting mechanical properties of the printed part is an active area of research. At the meltpool scale, the thermo-fluidic governing equations have been extensively modeled in the literature to understand the meltpool conditions and the thermal gradients in its vicinity. In many phenomena governed by partial differential equations, dimensional analysis and identification of important dimensionless numbers can provide significant insights into the process dynamics. In this context, a novel strategy using dimensional analysis and the method of linear least squares regression to numerically investigate the thermo-fluidic governing equations of the Laser Powder Bed Fusion AM process is presented in this work. First, the governing equations are solved using the Finite Element Method, and the model predictions are validated by comparing with experimentally estimated cooling rates, and with numerical results from the literature. Then, through dimensional analysis, an important dimensionless quantity - interpreted as a measure of heat ab- sorbed by the powdered material and the meltpool, is identified. This dimensionless measure of heat absorbed, along with classical dimensionless quantities such as Peclet, Marangoni, and Stefan numbers, is used to investigate advective transport in the meltpool for different alloys. Further, the framework is used to study the variations of thermal gradients and the solidification cooling rate. Important correlations linking meltpool morphology and microstructure evolution related variables with classical dimensionless numbers are the key contribution of this work.

Monte Carlo Filtering (MCF) is one of the methods of Experimental Statistical Energy Analysis (E-SEA), which allows the correction of a negative LF (Loss Factor). In this article, a modification of the MCF method, called DESA (Diagonal Extension of the Search Area), is proposed. The technique applies a non-uniform extension of the search area when generating a population of normalized energy matrices. The degree of expansion of the search area is controlled by the Diagonal Penalty Factor (DPF). The authors demonstrated the method's effectiveness on a system that could not be identified in several frequency bands by the classical MCF method. After applying DESA, it was possible to fill in the problematic bands that were missing CLF and DLF values. The paper also proposes a way to minimize the errors introduced by using overly high DPF values.

Hydraulic fracturing for oil-gas and geothermal reservoir stimulation is closely related to the generation and propagation of Mode I crack. Nonlinear deformation due to rock heterogeneity occurs at such crack tip, which causes the fracture process zone (FPZ) to form before the crack propagates unsteadily. However, the relationship between the FPZ characteristics and rock heterogeneity still remain elusive. We used three rock types common in reservoir for experimental investigation, and each of them includes two subtypes with different heterogeneity due to grain size or microstructural characteristics. Drawing on the experiment results, we calculated the FPZ size in each cracked chevron notched Brazilian disk, and we reproduced the formation process of the FPZ in marble by discrete element method. We showed that strong heterogeneity is favorable to large FPZ size, can enhance the ability of crack generation and complicate crack morphology. Coupling the Weibull distribution with fracture mechanics, the dependence of the FPZ size on heterogeneity degree can be theoretically explained, which suggests that inherent heterogeneity of rocks set physical foundation for formation of FPZ. These findings can improve our recognition to formation mechanism of the Mode I crack and provide useful guidelines for evaluating reservoir fracability.

Based on some geometrical properties of the Rabinovich system the closed-form solutions of the equations has been established. Moreover the Rabinovich system is reduced to a nonlinear differential equation depending on an auxiliary unknown function. The approximate analytical solutions are built using the Optimal Auxiliary Functions Method (OAFM). A good agreement between the analytical and corresponding numerical results has been performed. The accuracy of the obtained results emphasizes that this procedure could be successfully applied for more dynamical systems with these geometrical properties.

In a continuation and extension of an earlier publication, the calculation of the refractivity and polarizability of organic molecules at standard conditions is presented, applying a commonly applicable computer algorithm based on an atom-group additivity method, where the molecules are broken down into their constituting atoms, these again being further characterized by their immediate neighbor atoms. The calculation of their group contributions, carried out by means of a fast Gauss–Seidel fitting calculus, used the experimental data of 5988 molecules from literature. An immediate subsequent ten-fold cross-validation test confirmed the extraordinary accuracy of the prediction of the molar refractivity, indicated by a correlation coefficient R^2 and a cross-validated analog Q^2 of 0.9997, a standard deviation σ of 0.38, a cross-validated analog S of 0.41, and a mean absolute deviation of 0.76%. The high reliability of the predictions has been exemplified with three classes of molecules: ionic liquids, silicon- and boron-containing compounds. The corresponding molecular polarizabilities have been calculated indirectly from the refractivity using the inverse Lorentz-Lorenz relation. In addition, it could be shown that there is a close relationship between the "true" volume and the refractivity of a molecule, revealing an excellent correlation coefficient R^2 of 0.9645 and a mean absolute deviation of 7.53%.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

Gol'denveizer's problem of a torus has been analyzed by Audoly and Pomeau (2002) and Sun (2021). However, all of the investigations of Gol'denveizer's problem of an elastic torus have been linear. In this paper, the finite element method is used to more accurately address this problem. Furthermore, Sun (2021) cannot be solved by nonlinear analysis. We research the nonlinear mechanical properties of Gol'denveizer's problem of circular and elliptic tori, and relevant nephograms are given. We study the buckling of Gol'denveizer's problem of an elastic torus, and propose failure patterns and force-displacement curves of tori in the nonlinear range. Investigations reveal that circular tori have more rich buckling phenomena as the parameter a increases. Gol'denveizer's problem of the buckling of an elliptic torus is analyzed, and we find a new buckling phenomenon called a "skirt." As a/b increases, the collapse load of an elliptic torus of the Gol'denveizer problem is enhanced gradually.

Obtaining classification confidence at the pixel level is a challenging task for accuracy assessment in remote sensing image classification. Among the various methods for estimating classification confidence at the pixel level, interpolation-based methods have drawn special attention in the literature. Even though they have been widely recognized in the literature, their usefulness has not been rigorously evaluated. This paper conducts a comprehensive evaluation of three interpolation-based methods: local error matrix method, bootstrap method, and geostatistical method. We applied each of the three methods to three representative datasets with different spatial resolutions, spectral bands, and the number of classes. We then derive the estimated classification confidence and true classification confidence and compared the results with each other using both exploratory data analysis (bi-histogram) and statistical analysis (Willmott's d and Binned classification quality). The results indicate that the three interpolation methods provide some interesting insights on various aspects of estimating per-pixel classification confidence. Unfortunately, the interpolation assumes that classification confidence is smooth across the space, which is usually not true in practice. In other words, interpolation-based methods have limited practical use.

Some researchers in Taiwan argue that the current mechanism by which government subsidies are allocated for smart city demonstration projects warrants improvement. A comprehensive literature review determined that the development potential of smart cities should be prioritized in site selection for such demonstration projects. This study developed an evaluation framework on the basis of multi-criteria evaluation methods to enable the identification of suitable smart community demonstration sites. Evaluation criteria were first identified through the Delphi method. Next, the weights of each criterion were derived through the analytic hierarchy process. Furthermore, the capability of the proposed evaluation model was determined through simulation testing.

The research presented in this paper concerns the determination of the attraction basins of the Newton’s iterative method which was used to solve the non-linear systems of observational equations associated with the geodetic measurements. The authors considered simple observation systems corresponding to the intersections, or linear and angular resections, used in practice. The main goal was to investigate the properties of the sets of convergent in the initial points of the applied iterative method. An important issue regarding the possibility of automatic and quick selection of such points was also considered. Therefore, the answers to the questions regarding the geometric structure of the basins, their limitations, connectedness or self-similarity were sought. The research also concerned the iterative structures of the basins, i.e. maps of the number of iterations which are necessary to achieve the convergence of the Newton’s method. The determined basins were compared with the areas of convergence that result from theorems on the convergence of the Newton’s method, i.e. the conditions imposed on the eigenvalues and norms of the matrices of the studied iterative systems. One of the essential results of the research is the indication that the obtained basins of attraction contain areas resulting from the theoretical premises and their diameters can be comparable with the sizes of the analyzed geodetic structures. Consequently, in the analyzed cases it is possible to construct methods that enable quick selection of the initial starting points or automation of such selection. The paper also characterizes the global convergence mechanism of the Newton’s method for disconnected basins and, as a consequence, the non-local initial points, i.e. located far from the solution points.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

International guidelines are published in oncology to provide standardized information and fertility preservation (FP) care for adults and children with cancer. For benign gynecologic diseases (BGD), many recommendations are based on data coming from oncofertility studies rather than studies with a stronger and broader evidence base. The purpose of the study was to conduct a modified Delphi process for generating FP guidelines for BGD. A steering committee identified 42 potential FP practices for BGD. Then 114 key stakeholders were asked to participate in a modified Delphi process via two online survey rounds and a final meeting. Consensus was reached for 28 items. Among them, stakeholders rated age-specific information concerning the risk of diminished ovarian reserve after surgery as important but rejected proposals setting various upper and lower age limits for FP. All women should be informed about the benefit/risk balance of oocyte vitrification, in particular about the likelihood of live birth according to age. FP should not be offered in rASRM stages I and II endometriosis without endometriomas. These guidelines could be useful for gynecologists to identify situations at risk of infertility and to better inform women with BGDs who might need personalized counseling for FP.