Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water applications. This work presents a simulation study using a ray tracing methodology. With this technique we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations: stationary at 21° throughout the year and multi position setup; tilted with respect to the horizontal depending on three seasonal positions: 0° for summer, 16° for spring / autumn and 32° for winter, with the objective of increasing the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed system works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The methodology developed herein proved to be a valuable tool for prototype design and performance evaluation.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Hydrologic studies on rainfall-runoff have been extensively conducted in many regions around the globe to fulfill various desirable needs with a purpose of effective and proper planning and managing water resources for present and future uses, whereas such study is not well drawn much attention to river catchments of Tonle Sap Lake Basin in Cambodia, which may prevail to water insecurity. The Stung Sreng catchment, which is one among them considered to be a significant basin for water resources management in Cambodia, is remarkably increasing under intolerable pressures in water resources development. This study was to apply HEC-HMS (Hydrological Engineering Center-Hydrological Model System) model to predict streamflow of Stung Sangker catchment, located in Tonlesap Lake Basin in Cambodia. The result showed that the calibration was good at monthly basis. The model performance was given by Nash-Sutcliffe Efficiency criteria followed by 0.44 for daily and 0.71 for monthly basis, respectively. Moreover, the Percent Bias (PBIAS) for daily and monthly simulation was 4.13% and 3.56%, indicating a satisfactory model fit. The HEC-HMS conceptual model can be used to simulate flow of Stung Sangke catchment on a continuous time scale particularly monthly basis. The result also indicated that there was a clear seasonal variation in monthly water availability, especially during both wet and dry season.

The paper presents the main experimental capabilities of the automatic system for the study of the interaction between porous media and atmosphere. This system is one of the possible variants of patent 2-241-477. The paper shows the result of a drying and wetting study of a tailings sample. The sample is 32 cm in height and 29 cm in diameter. The saturation and drying process was carried out at 26 degrees Celsius at the sample surface, an air velocity of 2 m/s and a relative humidity of 60%. The recharge applied to the column surface was 0.3 cm3/cm2/minute. The results show the effectiveness of the system in controlling the spatial-temporal variation of different physical properties of the porous medium in the vertical and surface profile. The controlled variables include volumetric water content, suction, relative humidity, sample weight variation due to recharge or drying, shrinkage, temperature, etc. The experiment shows how the tailings saturate very quickly but dry very slowly. Tailings consolidation occurs in the drying and wetting processes, being higher in the first one.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

Although corn is the most important and nitrogen (N)-fertilized crop, there is a lack of long-term data on the effects of organic and inorganic N fertilizer on N balance and losses for corn systems under different tillage systems. From 2012 to 2023 we assessed the effects of N sources on grain yields from cultivated continuous corn receiving irrigation at a site with minimal erosion in Fort Collins, Colorado, USA, and compared these effects to no-till (NT) and strip till (ST) systems receiving inorganic N. An N balance accounting for N and carbon (C) sequestration found a system nitrogen use efficiency (NUE_Sys) for organic N fertilizer (manure) with tillage of 86.3%, which was higher than the NUE_Sys of 60.2% with inorganic N fertilizer (enhanced efficiency fertilizer, EEF). Conventional tillage with manure use is a good management practice that contributed to higher grain yields (2 of 11 yr.), C sequestration (P<0.05), soil organic N content (P<0.05), and soil phosphorus (P) content than inorganic N fertilizer with tillage (P<0.05). Tilled systems, whether receiving organic or inorganic N fertilizer, had higher yields and grain N content than NT and ST systems receiving inorganic N fertilizer (P<0.05). The grain production of the cultivated system receiving organic N fertilizer did not decrease with time, while the yields of the cultivated system receiving inorganic N fertilizer decreased with time (P<0.05), suggesting that cultivated systems receiving organic N fertilizer may be more sustainable and better able to adapt to a changing climate. Additionally, a combination of manure (30% of N input) with EEF (70% of N input) contributed to a synergistic effect that increased agronomic productivity (harvested grain yields).

This study aims to enhance the detection and assessment of safety hazards in small-scale reservoir engineering using advanced image processing and deep learning techniques. Given the critical importance of small reservoirs in flood management, water supply, and ecological balance, the effective monitoring of their structural integrity is crucial. This paper developed a fully convolutional semantic segmentation method for hidden danger images of small reservoirs using an encoding-decoding structure, utilizing a deep learning framework of convolutional neural networks (CNNs) to process and analyze high-resolution images captured by UAVs. The method incorporated data augmentation and adaptive learning techniques to improve model accuracy under diverse environmental conditions. Finally, the quantification data of hidden dangers (length, width, area, etc.) was obtained by converting the image pixels to the actual size. Results demonstrate significant improvements in detecting structural deficiencies, such as cracks and seepage areas, with increased precision and recall rates compared to conventional methods, and the HHSN-25 network (Hidden Hazard Segmentation Network with 25 layers)proposed in this paper outperforms other methods. The main evaluation indicator mIoU of HHSN-25 is higher than other methods, reaching 87.00%, and Unet is 85.50%, Unet++is 85.55%. The proposed model achieves reliable real-time performance, allowing for early warning and effective management of potential risks. This study contributes to the development of more efficient monitoring systems for small-scale reservoirs, enhancing their safety and operational sustainability.

This paper proposes Pierre Bourdieu's sociological concepts of social field, capital, and habitus to analyze water management in Colombia. By mapping the social dynamics of water management, this study examines the interactions and power relationships among agents, including government agencies, private companies, academic institutions, non-profits, and local communities. The analysis reveals how various forms of capital, such as economic, cultural, social, and symbolic, influence water management practices, policies, and the distribution of power. Integrating agent-based modeling with hydrological simulations provides a more nuanced understanding of how social dynamics influence water management. This interdisciplinary approach helps develop more adaptive and equitable strategies by capturing the complex interactions between human behavior and environmental factors. The research demonstrates that agent-based modeling, informed by Bourdieu's sociological framework, offers valuable insights for policy development in regions facing socio-economic and environmental challenges. The study highlights the need to localize the analysis of the social field to capture regional customs and specific social dynamics. This localized approach ensures that water management strategies are more relevant, context-sensitive, and sustainable. This paper advocates for the wider adoption of agent-based modeling in water management, proposing a methodology that combines the engineering principles of practical problem-solving and adaptive design with an understanding of the social complexities in water management.

Roof and roofings built to protect the housing and homeowner from undesirable rainwater, have been seen an important structural element throughout history in the entire of housing. In this research, structural and spatial relationships between building envelope with isolation from water in traditional housing architecture are analyzed. Roof, eaves and rain gutters which are isolation from water items were investigated according to shapes, slope direction, materials, carrier systems and covering materials. The qualification of the roofing, eave and rain gutter elements which are equipment elements related to the comfort of the building envelope and the extent of changes in these elements were examined at the traditional housing level. Exemplary, the traditional housing in the city of Trabzon in Turkey were selected. During the completion process of the working, detailed aims related to structure-health reinforcements were specified with the relevant literature review. The chart form has been developed for compilation of information about the general characteristics of the housing in the research area and the building-health reinforcements within the aim of the research. Exemplary houses were selected by external observation technique and the data obtained as a result of observations, interview and determinations related to general characteristics and building-health reinforcements of these housing were handled into a chart form. By evaluating the data obtained; harmony and contrasts in system level practices, the dimensional properties of the elements at the spatial level, the greatness and accuracy levels preferred in various fittings, the harmony and contrasts in the materials, dimensions and practices of the elements at the system and spatial level, harmony and contrasts of applications of new opportunities at the level of building-health reinforcements in traditional housing, conclusions were drawn to identify special and general situations at the level of building-health reinforcements and to obtain information about the comfort requirements of traditional housing. Nowadays, where the health of the building, which is mostly ignored, is gaining importance day by day, concrete and applicable solution data are presented and interpreted for new designs to be made in this direction.

The environmental vulnerability diagnosis of a river basin depends on a holistic analysis of its environmental aspects and degradation factors. Based on this diagnosis, the definition of priority areas where interventions for environmental recovery should be carried out is fundamental, since financial and natural resources are limited. In this study, we developed a methodology to assess these fragilities using an Environmental Vulnerability Index (EVI) that combines physical and environmental indicators related to the natural sensitivity of ecosystems and their exposure to anthropogenic factors. The EVI developed was applied to the headwater’s region of the São Francisco River basin, Brazil. The proposed index was based on the AHP multi-criteria analysis and was adapted to include four variables representative of the study area: Land Use Adequacy, Burned Area, Erosion Susceptibility and Quantitative Water Balance. The EVI analysis highlighted that the presence of easily erodible soils, associated with sloping areas and land uses above their capacity, generate the most vulnerable areas in the headwaters of the São Francisco River basin. The results of this study indicate where resources should be applied for environmental preservation in the basin under study, directing the allocation of efforts to areas with lower resilience in maintaining ecosystem services.

Microalgae cultivation for biotechnological purposes is an expanding field. Their cultivation is usually performed on a liquid culture medium and require the presence of an energy source. Culture media are water-salt solutions containing nitrogen, sulfur, phosphate sources, with trace of transition metals. Light source supplies energy through photosynthesis process, resulting in metabolic reactions and cell growth. Thanks to the huge number of existing species and their diversity, it is possible to exploit alternative water sources with chemical and physical properties far from the commonly used freshwater media. Among these, oilfield or formation waters (AFW) are saline wastewater produced during oil drilling. They represent over 95 % of the total fluids collected from gas and oil wells during fuel extraction. This study exploits the adaptation capability of a Galdieria sulphuraria strain in different salinity conditions to build up a more feasible microalgae-based platform. Batch cultivation of G. sulphuraria was evaluated in a range from 0 to 20 g/L NaCl in terms of growth rate, metabolite content, photophysiology, and intracellular redox state. Moreover, the same strain has been tested for artificial formation water growth in semicontinuous cultivation mode. In these condition, NaCl preadaptation effect has been assessed too. Results clearly demonstrate that biomass composition is influenced from medium salinity. Strains preadapted in 0 to 20 g/L range of NaCl salinity show almost same cell growth profile and a slightly different ratio between lipids, carbohydrates, and proteins. Pigments content and photophysiology point out that variations of osmotic pressure and ionic strength in medium affect Photosystem II (PSII). Regulation of light harvesting is necessary to trigger metabolism shift toward synthesis of metabolites required in the adaptation process.

This study aimed to evaluate the effects of plasma treated metal contaminated water, used for irrigation, on plant growth. Zinc (Zn) is one of the more commonly used metals. It can enter the environment from industrial processes as particles released into the atmosphere or as wastewater discharged into waterways or the ground. Exposure to large amounts of zinc, even for a short time, can seriously affect human health. In this experiment, three different DBD O2 plasma treated zinc contaminated water and a control (tap water) were used, with Arabidopsis thaliana as the model plant. The treatments were: i) Control, ii) Zn water, iii) Zn+O3(30 min), and iv) Zn+O3(60 min). Arabidopsis plant exhibited maximum growth in the Zn+O3(30 min) treatment. All growth parameters, except leaf area, followed this trend: Zn+O3(30 min) > Control > Zn water > Zn+O3(60 min). Gene expression analysis revealed that reduced metal ion stress and controlled oxidation due to active oxygen species contributed to favorable/improved growth of Arabidopsis in the Zn+O3(30 min) treatment. Therefore, 30 minutes of DBD O2 plasma treated zinc contaminated water [Zn+O3(30 min)] can mitigate the adverse effects of excess zinc ions and promote the growth of Arabidopsis plants.

Industrial buildings have numerous energy-losing equipment, such as engines, ovens, boilers, and heat exchangers. Energy losses are related to inefficient energy use and lousy work conditions for the people inside the buildings. This work is devoted to the recovery of lost energy from industrial buildings. Firstly, the residual energy of the building is extracted to be used to warm water. Consequently, the work conditions of the people inside industrial buildings can be improved by maintaining the adequate temperature. The recovery energy is done by the multipurpose heat pump system (HP system). The working fluid used in the HP system is R134a, which is a traditional and cheap working fluid. The thermophysical properties of R134a are obtained through the PC-SAFT equation of state. This work presents a performance mapping based on the intercepted areas framework to evaluate which working conditions are the optimal operating variables. The latter depends on several key parameters, such as compressor work, heat delivery, heat absorbed, and exergetic efficiency. The results show that the optimal work conditions are found at different condenser and evaporator temperatures, and that may be limited by what the designer considers a good performance of the heat pump system.

This article aims to carry out experiments on water absorption by husked red rice, at constant temperatures of 28, 40 and 50 °C. The description of the absorption kinetics, as well as the analyses of water distribution and volumetric expansion of each grain, at a given instant, was done using a diffusion model. In order for the model to be as close as possible to the real physical situation, the mesh necessary to numerically solve the diffusion equation was generated from the photograph of a grain. Thus, the diffusion equation was written in Boundary-Fitted Coordinates (BFC). The solution of the diffusion equation written in generalized coordinates was then discretized in space and time, using the Finite Volume method, with a fully implicit formulation, considering variable volume and also variable mass diffusivity as a function of local moisture content. Optimizations based on Levenberg-Marquardt algorithm make it possible to determine the parameters of an exponential function relating mass diffusivity and the local moisture content for each temperature. Statistical indicators (chi-square, determination coefficient and Student’s t-test) allowed concluding that the model proposed was very satisfactory for all temperatures, making it possible to simulate water absorption, water distribution and volumetric expansion of the grain over time.

The Latin American Giant Observatory (LAGO) is a ground-based extended cosmic rays observatory designed to study transient astrophysical events, the role of the atmosphere on the formation of secondary particles, and space-weather-related phenomena. With the use of a network of Water Cherenkov Detectors, LAGO measures the secondary particle flux, a consequence of the interaction of astroparticles impinging on the Earth with the atmosphere. These interactions yield a flux of secondary particles that can be grouped into three distinct basic constituents: the electromagnetic, muonic, and hadronic components. In this work we extend our previous research by using detailed simulations of the expected atmospheric response to the primary flux and the corresponding response of our WCDs to atmospheric radiation. After implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD, we have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout LAGO distributed detection network and other astroparticles observatories for semi-automated, onboard and real-time data analysis. When a particle enters a Water Cherenkov Detector (WCD), it generates a measurable signal characterized by unique features correlating to the particle’s type and the detector’s specific response. The resulting charge histograms from these signals provide valuable insights into the flux of primary astroparticles and their key characteristics. However, this data is insufficient to effectively distinguish between the contributions of different secondary particles. This research extends our previous investigations, wherein we implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD. We have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. This methodology facilitates the differentiation among particle types and utilizes the detector’s nuanced response to each particle type, thus pinpointing the principal contributors within each group. In this work, we utilize OPTICS to analyze simulated data, further validating the proposed method. We created a simulated dataset by combining the outputs of the ARTI and MEIGA frameworks. This dataset simulates the expected WCD signals produced by the flux of secondary particles during one day at the LAGO site in Bariloche, Argentina, situated at 865 meters above sea level. To achieve this, real-time magnetospheric and local atmospheric conditions for February and March of 2012 were analyzed, and the resultant atmospheric secondary-particle flux was integrated into a specific MEIGA application featuring a comprehensive Geant4 model of the WCD at this LAGO location. The output from MEIGA was modified for effective integration into our machine learning pipeline. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard and real-time data analysis. Our analysis demonstrates that OPTICS can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard data analysis.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

Coastal environments are complex systems that are influenced by a combination of natural processes and human activities. Scientific interest in the effects of coastal erosion/accretion and climatic change-related processes greatly increased in recent decades due to the growing human development along coastal areas. This paper investigates the state and evolution of beach-dune systems for the 1977-2001 and 2001-2019 periods of the Mediterranean coast of Andalusia (Spain) using two different proxies: the dune toe line, which was used to track foredunes evolution, and the high-water line, which was used to assess shoreline evolution. Results showed a general erosional behavior of the studied beach-dune systems and identified cases where the main trend was altered through human interventions. In the 1977-2001 period, 54% of foredunes showed erosion, 24% accretion and 22% stability while and 34% of shorelines showed erosion, 40% accretion and 34% stability. In the 2001-2019 period, 42% of foredunes showed erosion, 28% accretion and 30% stability, and 40% of shorelines showed erosion, 34% accretion and 26% stability. Combining the evolution classes of each proxy (dune toe/shoreline) allows the behavior of both shoreline proxies to be assed together and provides insights additional to those derive from the use of a single proxy. In this regard, Erosion/Erosion (EE) was the most frequent behavior, with 25% and 27% in the first and second periods respectively, and Accretion/Accretion (AA), with 17% in both periods. Erosion of foredunes combined with stability or accretion of the shoreline (ES and EA) were the most common pairings in the first period, while stability of dunes combined with accretion of the shoreline (SA) and Stability/Stability (SS) dominated in the second period. The results obtained provide additional insights on the nature and drivers of coastal change that aid local coastal managers and administrations in understanding erosion processes. The method can be applied at other areas around the world where a similar data base is available.

A flat-plate unglazed solar water heater (SWH) with polymer thermal absorber was developed and tested. Polymer thermal absorber as a viable alternative to metal thermal absorber that is found in most SWH systems. The performance of this polymer SWH system is measured based on inlet and outlet water temperature, water flowrate, ambient air temperature and solar irradiance. The polymer thermal absorbers are hollow Polyvinyl Chloride (PVC) pipes with 20mm external diameter and 3 mm thick, painted in black to enhance radiation absorption. The pipes are arranged in a rectangular spiral inward-outward opposing-flow (RSioof). The collector pipes are placed in a 1 m2 square enclosure with bottom insulation and reflective surface for better radiation capture. Water circulation is a closed loop with a 16-liter uninsulated storage tank, driven by a pump and controlled by valves to maintain a mass flow rate of 0.00031 to 0.00034 kg/s. The test was conducted under partially clouded sky from 9 am to 5 pm, with solar irradiance between 105 and 1003 W/m2 and 27-36oC ambient air temperature. The SHW produced outlet hot water at 65oC by mid-day and maintained the storage temperature at 63oC until the end of test duration. Photo-thermal energy conversion was recorded with 23% maximum value. Results indicate that a flat plate solar water heater with polymer thermal absorber in RSioof design can be an effective alternative to the metal thermal absorber solar water heater and can be further optimized with glazing and tube sizing.

Along with the increasing industrialization of contries and population growth, the global. With the thougth of overcoming climate change and renducing greenhouse gas emissions in the atmosphere, interest in alternative sloar, wind, water, geothermal, tidal and ocean wave energy has significantly increased. Hydropower is one of the most used inexhaustible sources of energy on a global scale. The efficiency of water turbines can be increased by optimizing the blade cascade and the casing. For this purpose, research is conducted on specialized laboratory benches. The purpose is to determine the influencing parameters which affecting the nature of the power and cavitaion curves This paper presents the results of numerical and laboratoty studies of axial hydrokinetic turbines. A detailed analysis of the influence of the geometric parameters of the blades on the operating curves is made. A mathematica model for synthesis of the blade cascade is derived. An assessment of water energy soures has been made and sites of high energy potential have been pointed. The present material can be used for development of a methodology for calculation of efficient axial hydrokinetic turbines.

This review paper presents a comprehensive synthesis of current knowledge on the contamination of water systems by polycyclic aromatic hydrocarbons (PAHs). PAHs, organic contaminants characterized by two or more fused aromatic rings, are notably problematic due to their persistence, bioaccumulation, and significant health risks. The review commences with an examination of various sources of PAHs in aquatic environments, encompassing both anthropogenic activities, such as industrial discharges, urban runoff, and oil spills, and natural phenomena including volcanic eruptions and wildfires. Subsequently, the discussion shifts to the distribution patterns of PAHs within different aquatic ecosystems, with an analysis of factors that influence their transport. Considerable focus is placed on the entry mechanisms of PAHs into water systems and their interactions with diverse environmental matrices. Additionally, the ecotoxicological effects of PAHs on aquatic life are scrutinized, with particular emphasis on molecular, individual, and ecosystemic impacts. This includes an exploration of PAH bioaccumulation in aquatic organisms and their potential mutagenic and carcinogenic consequences. The review further addresses the challenges associated with detecting and quantifying PAHs in aquatic settings, reflecting on the advancements in analytical methodologies and the complexities introduced by their varied physicochemical properties. The paper concludes with a summary of existing regulatory frameworks and guidelines governing PAH contamination in water systems, underscoring the imperative for global collaboration in the monitoring and management of PAH pollution.

The purpose of this review is to investigate the role of legume cover crops in improving climate adaptability and water use efficiency in South African grassland systems. Climate change is posing significant obstacles to agricultural systems all over the world, which includes South Africa, where shortages of water and fluctuations are significant issues. Legume cover crops are growing in popularity as a long-term and cost-effective solution to these problems. The purpose of this review is to demonstrate the possible advantages of legume cover crops for enhancing climate resilience and water use efficiency in South African grassland systems, as well as the fundamental processes and present study findings. According to the outcomes, legume cover crops may boost soil water availability, nutrient cycling, carbon sequestration, and overall ecosystem productivity, resulting in increased climate resilience and water use efficiency. However, a variety of factors, including species selection, management practices, and environmental conditions, can all have an impact on the effectiveness of legume cover crops. With the concerted efforts, adaptation strategies of livestock farmers that seeks to maximise the potential of legume cover crops in South African grassland systems, it is critical to consider site-specific factors when establishing them. This review offers significant insights into the role of legume cover crops in climate resilience and water use efficiency, laying the groundwork for future research and agricultural practices.

This paper investigates women’s empowerment and their active involvement in governance aimed at promoting sustainable development. The study focuses on examining the roles and processes of co-creation of nature-based solutions (NBS) for water management in Milan. Three research directions were explored: 1) to determine gender-based roles within local governance; 2) to detect semantic groups of NBS based on stakeholders' gender; c) to analyze gender-based linguistic and conceptual patterns of NBS. To achieve our objectives, we converted a sample of audio-video interviews of local stakeholders into textual data along with metadata indicating speakers' roles and gender. Descriptive statistics were applied to explore the governance's roles. We employed a combination of textual analysis and network analysis to identify thematic groups of NBS, and applied a word embedding approach to uncover linguistic patterns indicative of semantic sub-structures. The findings revealed significant demographic diversity. Male stakeholders perceive sustainable development as a process driven by the circular economy and the coordination of territorial authorities, while female stakeholders envision a transformative approach rooted in science, culture, and collaboration. The semantic sub-structure analysis highlighted a tendency among male governance to emphasize specialized skills, whereas female governance placed greater emphasis on problem definition rather than resolution.

One of the measures required by the European Green Deal to decarbonise the freight transport sector is the promotion of inland waterway transport (IWT), in particular intermodal transport in Europe. To facilitate intermodal transport on the Danube, we developed six new barge designs for the transport of 45' pallet-wide high-cube containers using a four-step approach. Our approach consisted of detailed desk research, followed by design and further analysis of the identified barge types, taking into account, for example, sight lines or stability. The container carrying capacity reaches up to 90 containers in three layers, which is double the capacity of existing standard barges on the Danube. Nevertheless, three-layer transport is hardly feasible in several cases, due to restrictions regarding sight lines and stability. We conclude that each loading condition must be evaluated separately to determine the best barge design option for each case. The study is limited by its geographical scope and the type of container used to develop the new barge designs. This could be a possible direction for further research on this topic: using other container types and/or extending the geographical scope.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomass such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240°C), molding time (5-30 min), fiber/fine particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials. The density ranged from 1198 to 1507 kg/m3, the flexural modulus from 0.9 to 6.9 GPa and the flexural strength at breaking point from 6.1 to 43.6 MPa. Water absorption (WA) and thickness swelling (TS) respectively ranged from 21% to 240% and from 9% to 208%. Higher mechanical properties were obtained using SCB with fine particles, low moisture content (4-10%), high temperature (≥ 200°C) and pressure (≥ 68 MPa), while water resistance was improved using more severe thermocompression conditions with the highest temperature (240°C) and time (30 min) or a higher moisture content (≥ 12.5%). Correlations were noted between the mechanical properties and density, while the material obtained with only fine particles had the highest mechanical properties and density. Material obtained with a 30 min molding time had the lowest WA and TS due to internal chemical reorganization followed by hemicellulose hydrolysis into water-soluble extractables.

Soybean a pulse of considerable nutritional value due to its high protein, fibers and polyunsaturated fatty acid (PUFA) contents, also contains phytoestrogenic compounds that definitely hinder its recommendation for general consumption. Contrarily to ancient times when soybeans were boiled, modern commercial soy-foods can contain up to 150 mg/100g of estrogenic isoflavones. Interestingly, current estimations of isoflavone intake in the literature do not distinguish between the origins of soy-food i.e. home-made or commercial. As a result, the isoflavone exposure in Asian countries may well be over-estimated. This study aims to demonstrate, based on step-by-step monitoring of isoflavones, that traditional and domestic treatments, leveraging isoflavones water-solubility, can indeed significantly reduce their content in soy-foods. Indeed, when compared to commercial foods, the isoflavone contents was found to be 20, 2.6, 4.5 and 9.8 times lower in “home-made” soy-juice, tofu, tempeh and miso, respectively. Additionally, water soaking was found to reduce the isoflavones levels in soy-textured-proteins by more than 70%. Hence, this simple process has the potential to help drastically reduce overall xenoestrogens exposure. This study could serve as a basis for establishing the isoflavones Reference Dose and issuing food safety guidelines.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

Pollutants accumulate in aquatic habitats as a result of mining activities. Lemna gibba and Lemna minor were used in this study to examine the accumulation capacities of Mo+, Pb+, and Cu++ in the acid fluids of the copper mining. Duckweed family includes water plants like L. minor and L. gibba. These are tiny, delicate, free-floating aquatic plants. Two reactors were assigned to L. gibba and L. minor, respectively. Throughout the course of eight days, these plants and reactor water were gathered every day. The acid mine water's pH, temperature, and electric conductivity were also tested every day. The L. gibba and L. minor were cleaned, dehydrated, and burned in a drying oven for a whole day at 300 oC. ICP-MS (Inductively Coupled Plasma Mass Spectroscopy) was used to determine the Mo+, Pb+, and Cu++ content of the plant and water samples. The concentrations of Mo, Pb, and Cu in the acid mine fluids of the copper mining were 30±4, 260±12, and 15535±322 μg L−1, respectively.in that order. When it came to extracting Mo, Pb, and Cu from the acidic fluids of the copper mining, L. gibba and L. minor performed well and efficiently compared to control samples; they did so 29 and 177 times for Mo, 30 and 109 times for Pb, and 495 and 1150 times for Cu. Considering all these findings, it has been shown that L. gibba and L. minor have the ability to efficiently remove Mo, Pb and Cu in acid mine fluids and can be good rehabilitation plants for polluted waters.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

Under the extreme shortage of water resources in the Yellow River Basin, it is of great signifi-cance to analyze the spatial distribution relationship between rural settlement and water re-sources for the coordinated development of human and water resources in the Yellow River Ba-sin. However, the water allocation scheme depended on statistical data in the previous work, not on rural settlements in space. Furthermore, previous researches seldom focus on the evaluation of surface water resources accessibility according to the spatial distribution characteristics of ru-ral settlements and water resources, especially, in the Yellow River Basin and using rural set-tlement as unit. Therefore, a quantitative evaluation model of surface water resources accessibil-ity is constructed by using the GIS network analysis method, taking rural settlement as the re-search unit, based on three dimensions of topography, distance, and surface water resources, at the Yellow River basin scale. The results show that: (1) The surface runoff of rural settlement in the Yellow River basin is mostly less than 0.05 km/m2, reaching 99.83%. In other words, the Yel-low River Basin is extremely short of water resources. The surface water resources accessibility is affected by distance, topography, and surface water resources. The evaluation results show that the range of surface water resources accessibility is 0.13~0.88, with an average value of 0.47 and a standard deviation of 0.05. The High surface water resources accessibility value in the Yel-low River Basin is in the east and west, and the low value is mainly distributed in the middle. (2) The range from low to high of surface water resources accessibility in 12 catchments is Sanmen-xia station, Lanzhou station, Shizuishan station, Longmen station, Tongguan station, Toudaoguai station, Xiaolangdi station, Huayuankou station, Lijin station, Gaocun station, Ai Shan station and Tangnaihai station. (3) The value of surface water resources accessibility at the city scale is higher in the east of 10 cities and in the west of 1 city. However, it is lower in the west of 9 cities. And the values of the other cities are at a medium level. The correlation coefficient with primary industry GDP and surface water resources accessibility is 0.271 (N=56, Sig=0.043, in 0.05 level, the correlation is significant), which verifies the rationality of surface water resources accessibility model to some extent.

Little is known about how the degree of mixing of forest-forming species affects forest floor hydrology. We evaluated the water storage capacity of the resulting litter layer by mixing litterfall of Scots pine and sessile oak and studying their decomposition time. We prepared 90 artificial samples containing pure pine litter, pure oak litter, and mixed pine-oak litter with varying shares of pine needles. These samples were subjected to 15 months of decomposition in soil. After every three months of decay, some samples were removed from the soil, and their water storage capacity, bulk density, and C:N ratio were evaluated. Our findings indicate that samples with the greatest water storage capacity had a low C:N ratio and a predominant share of oak leaves. Conversely, samples with a high C:N ratio and a predominant share of pine needles had the lowest water storage capacity. After 12 and 15 months of decomposition, the water storage capacity increased by more than 52% compared to the initial water capacity of the samples. The highest increase in water storage capacity (>40%) was observed in samples with a predominant share of oak leaves, while the lowest (approximately 28%) was recorded in samples with 80 and 100% of pine needles.

Cultures in Mediterranean climate zones (MCZs) around the world have long been reliant on groundwater and springs as freshwater sources. While their ecology and cultural sustainability are recognized as critically important, inter-relationships between springs and culture in MCZs has received little attention. Here we augmented a global literature review with case studies in MCZ cultural landscapes to examine the intensity of cultural and socio-economic impacts on springs ecohydrogeology. MCZs are often oriented on the west and southern coasts in tectonically active landscapes, which control aquifer structure, the prevalence of westerly winds, and aridity, and generally expose associated habitats to harsh, afternoon sunlight. Cultural appreciation and appropriation of springs ranges widely, from their use as subsitence supplies to profound traditions, such as Greco-Roman nymphs, and Asian and Abrahamic spiritual cleansing and baptism. Commoditization of water resources for agriculture, industry (e.g., mining, water bottling, geothermal resorts), and urban needs is placing ever-increasing, non-sustainable demands on aquifers and springs. When economic values approach or exceed cultural values, these irreplaceable aquatic resources are degraded and lost. Sustainable stewardship of springs and the aquifers that support them are a little-recognized, but central conservation challenge for modern society facing global climate changes.

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

The three-component reaction of enaminones, benzaldehyde and hydrazine-HCl or four-component reaction of enaminones, benzaldehyde, hydrazine–HCl and ethyl cyanoacetate in water in the presence of catalytic amount of ammonium acetate has been devised as a straightforward , sustainable approach for the synthesis of 1-H-pyrazole, N-aminopyridine and pyrazol[3,4-b]pyridine derivatives . The key benefits of this approach is simple experimental procedure associated with cost effective and environmentally friendly techniques.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

The European Fish Index EFI+ is the only fish-based multimetric index for the assessment of the ecological status of running waters validated and thus applicable across the European Union. Metrics of the index rely on several attributes of the species present in the fish assemblage, irrespective of their native/alien status. The abundance of alien fish, together with other anthropogenic impacts, is one of the most important threats to the conservation of native fish and ecosystem health and is also an indicator of degraded stream conditions. Therefore, to improve the performance and utility of the EFI+ in regions with high incidence of alien species, the EFI+ was adapted to include the alien fish pressure by averaging the two original metrics with a new metric that reflects the number of alien species as well as the proportional abundance of alien individuals. The application of the adapted index (A-EFI+) is illustrated with data from several Iberian Mediterranean basins and showed similar or stronger correlations than the original EFI+ with anthropogenic pressure (land-use variables) and with other regional fish indices. EFI+ has been invaluable to intercalibrate fish indices across Europe and A-EFI+ is similar but explicitly includes the alien pressure, thus helping to provide a more comprehensive assessment of ecosystem health and to communicate it to society.

Pistol shrimps generate cavitation bubbles. Cavitation impacts due to bubble collapses are harmful phenomena, as they cause severe damage to hydraulic machineries, such as pumps and valves. However, cavitation impacts can be utilized for mechanical surface treatment to improve the fatigue strength of metallic materials, which is called “cavitation peening”. Through conventional cavitation peening, a cavitation is generated by a submerged water jet, i.e., a cavitating jet or a pulsed laser. The fatigue strength of magnesium alloy when treated by the pulsed laser is larger than that of the jet. In order to drastically increase the processing efficiency of cavitation peening, the mechanism of pistol shrimp (specifically when used to create a cavitation bubble), i.e., alpheus randalli, was quantitatively investigated. It was found that a pulsed water jet generates a cavitation bubble when a shrimp snaps its claws. Furthermore, two types of cavitation generators were developed, namely, one that uses a pulsed laser and one that uses a piezo actuator, and this was achieved by mimicing a pistol shrimp.

Food and nutrition insecurity, affecting 30% of the global population in 2020, poses a significant challenge to achieving Sustainable Development Goal (SDG) 2 - Zero Hunger. Urbanization, particularly in sub-Saharan African cities e.g. Lagos, Nigeria, exacerbates these issues, impacting resources and contributing to informal settlements. There is emphasis on innovative solutions in urban farming, with Recirculating Aquaculture Systems (RAS) emerging as one of the promising approach due to its efficiency in space and capital utilization. However, maintaining optimal conditions in RAS, crucial for SDG 2 and 11, requires robust water quality monitoring. This study explores the availability of digital tools for water quality monitoring in small-scale urban RAS, evaluating handheld devices and IoT sensors' reliability through t-test statistical method. The results aim to guide practitioners in selecting effective monitoring tools, contributing valuable insights for sustainable aquaculture in urban areas, particularly in sub-Saharan Africa, where access to affordable digital solutions is pivotal for success and can attract youth to agri-food technologies.

The adsorption of actinide ions (Am(III) and U(VI)) from aqueous solutions by pristine and oxidized carbon fabrics has been investigated by means of batch experiments at different pH values (4, 7 and 9) and temperatures (25, 35 and 45 °C) under ambient atmospheric conditions. The experimental results indicate that both pH and fabric texture affect the adsorption rate and the relative removal efficiency, which results at 70% and 100% for Am(III) and U(VI), respectively. The Kd (L/kg) values for U(VI) have been generally found to be higher (2 &lt; log10(Kd)&lt; 3) than the corresponding values for the Am(III) adsorption (1.5 &lt; log10(Kd) &lt; 2). The data obtained from the experiments regarding the temperature effect imply that the relative adsorption for both actinides increases with temperature and that the adsorption is an endothermic and entropy-driven reaction. Application of the fabrics to remove the two actinides from contaminated seawater samples shows that both the relative removal efficiency and the Kd values decrease significantly due to the presence of competitive cations (e.g., Ca2+ and Fe3+) and complexing anions (CO32-) in the respective waters. Nevertheless, the removal efficiency is still remarkable (50% and 90% for Am(III) and U(VI), respectively), demonstrating that these materials could be attractive candidates for the treatment of radionuclide/actinide contaminated waters.

Seasonal snowpacks, characterized by their snow water equivalent (SWE), play a major role in the hydrological cycle, snow melt contributions to floods and the subsequent availability of water resources downstream. Accurately estimating SWE and understanding its spatial and temporal variations presents a considerable challenge, particularly within mountainous regions characterized by complex terrain and limited observational data. Seeking to enhance the performance of the widely used Soil and Water Assessment Tool (SWAT), we report a new approach characterising snowpack behaviour incorporating both modelled and remotely sensed derived SWE calibration data. We focus on the Chenab River Basin (CRB) a headwater catchment of the Indus Basin, globally significant in terms of human inhabitants and intensifying flood risk due to climate change. We conducted a thorough assessment of five satellite-derived and reanalysis-based precipitation datasets: ERA5-Land, CMORPH, TRMM, APHRODITE, and CPC UPP. This reveals significant levels of uncertainty in global precipitation products when compared to reference data from observed stations as well as in the resulting simulated streamflow from the SWAT model. Subsequently, we expanded the scope of the SWAT model to encompass the spatial and temporal simulation of SWE. This was achieved by incorporating information from remotely sensed and modelled SWE products, manually adjusting snow parameters in R-SWAT for both the main basin and at sub-basin scales. Integrating SWE from reference snow products into the calibration process, alongside streamflow data, substantially enhanced modelling accuracy to simulate SWE compared to the conventional auto-calibration and single-variable approaches reliant solely on streamflow data. This approach results in considerable improvement in SWE predictions and to some extent in streamflow simulation in catchments dominated by snow. This research highlights the potential of remote sensing and modelled SWE parameterisation in the absence of in-situ snowpack data in high-altitude environments. An improved understanding of SWE behaviour is vital for predicting hydrological responses spanning hazards to water resources in the populous downstream regions of the Indus Basin, especially in the face of climate change.

The presence of heavy metals in industrial effluents has recently become a source of concern for human health and the environment. Efficient removal of metal ions and wastewater treatment is essential for protecting public health and the environment. In this study, we present an eco-friendly, green synthesis of reactive and fully dispersed zerovalent iron nanoparticles (nZVI) in carbon nanofibers via an electrospinning technique. In this novel study, green tea (GT) was used as environmentally friendly, polyvinyl alcohol (PVA) was used for the stabilization and reduction of nZVI, and tetraethyl orthosilicate (TEOS) was added to provide flexibility and to increase the specific surface area of the nZVI based nanofibers. GT contains polyphenols, which act as reducing agents, converting iron ions into nZVI and the particles can then serve as the building blocks for the carbon nanofibers. TEOS can also contribute to the stability of the nZVI by coating their surfaces with a silica layer. This silica layer helps prevent the oxidation of the nZVI, thereby reducing their catalytic activity. The nZVI-based composite (∼ 400 nm) / carbonized (∼ 200 nm) nanofibrous mats were fully characterized by scanning electron microscopy. The average size of the nZVI embedded in the composite and carbonized nanofibers can range from 50 nm to 100 nm. The x-ray diffraction (XRD) analysis of nZVI-based carbon nanofibers showed that there is no crystallinity and a single-phase cubic structure. Both energy-dispersive X-ray spectroscopy (EDX) and Fourier transform infrared (FTIR) analysis also confirmed the formation of single-phase nZVI-based composite / carbonized nanofibers. The high intensity of the peaks in the FTIR spectrum indicates the formation of nZVI in the nanofibers structure. The electrospun nZVI-based carbon nanofibers have a higher surface area and better reactivity due to small particle size and large surface area-to-volume ratio. They can provide excellent water stability and dispersibility in water compared to bulk nZVI, which tend to agglomerate and settle quickly. Additionally, nanofiber morphology can enhance the mechanical strength and durability of the composite material. Due to low-cost synthesis and their high efficiency in removing pollutants, these nanofibers could be used as nano-filters for wastewater treatment.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

Abstract: The species composition, the structure of phytoplankton communities, hydrochemical parameters in the artificial cooling reservoir of one of the largest thermal power plants (TPP) in the north-east of Europe in the Pechora River basin, Komi Republic were studied in the ice-open period in June and August. Altogether 81 species of algae and cyanobacteria was revealed with the last one predominated. Among cyanobacteria and algae (Bacillariophyta, Chlorophyta), indicators of water quality were found. Assessment of water quality according to the species composition and abundance of indicator phytoplankton species showed that the waters of the Pechorskoe Reservoir can be at-tributed to the III class of water quality, beta-mesosaprobic self-purification zone, with water quality of satisfactory purity, retaining the ability to self-purify. An increase in the diversity of plankton communities and high values of their abundance and biomass under the influence of the warming effect of TPP water outlet were noted and revealed its spatial distribution over the reservoir surface. The plankton of the northern reservoir under the influence of warm waters indicates a slight in-crease in the trophic status of the studied water body, which is also confirmed by the data of hydrochemical analysis. Ecological mapping for the chemical and biological variables as well as pollution indices over the water area of the reservoir was carried out. The results obtained can be used to make forecasts of changes in the phototrophic biota of small northern water bodies under the conditions of climate change.

Towards better understanding of factors controlling carbon (C) exchange between inland waters and atmosphere, we addressed inorganic carbon cycle in semi-arid lakes of Central Eurasia, subjected to strong impact of on-going climate change. For this, we assessed the hydrochemical vari-ability and quantified its control on formation of authigenic carbonate minerals, occurring within the upper layer of sediments in 43 semiarid lakes located in the southwest of Western Siberia (Central Eurasia). Based on measurements of pH, total dissolved solids (TDS), cationic and anionic composition, dissolved organic and inorganic C, as well as textural and mineralogical characterization of bottom sediments using X-ray diffraction and scanning electron microscopy, we demonstrate that lake water pH and TDS are primarily controlled by both lithological and climatic context of the lake watershed. We have not revealed any direct relationships between lake morphology and water chemistry. The most common authigenic carbonates scavenging atmospheric CO2 in the form of insoluble minerals in lake sediments were calcite, aragonite, Mg-calcite, dolomite and hydro-magnesite. The calcite was the most common component, aragonite mainly appears in lakes with sediments enriched in gastropod shells or artemia cysts, while hydromagnesite was most common in lakes with high Mg/Ca molar ratios, as well at high DIC concentrations. The relationships between mineral formation and water chemistry established in this study can be generalized to a wide suite of arid and semi-arid lakes in order to characterize current status of inorganic C cycle and predict its possible modification under on-going climate warming such as water temperature rise and change of hydrological connectivity, primary productivity and nutrient regime.

The inner walls of drinking water distribution system (DWDS) are expected to be clean to ensure a safe quality of drinking water. In reality, complex physical, chemical and biological processes take place when water comes into contact with the pipe surface. This paper describes the impact of leaching different compounds from the water supply pipes into the drinking water and subsequent risks. Among these compounds there are heavy metals. It is necessary to prevent these metals to get into the DWDS. Those compounds are susceptible to impact the quality of the water delivered to population either by leaching dangerous chemicals into the water or by enhancing the development of microorganism growth on the pipe surface. The corrosion process of different pipes materials, scale formation mechanisms and the impact of bacteria formed in corrosion layers are discussed. Water treatment processes and the pipe materials also affect the water composition. Pipes materials act differently in the flowing and stagnation conditions. Also, they age differently (e.g metal based pipes are subjected to corrosion while polymer based pipes have a decreased mechanical resistance) and are susceptible to enhance bacterial film formation. This review helps to clarify what are the possible sources of compounds responsible for drinking water quality degradation. Also, it gives guidance on the measures that are needed to maintain a stable and safe drinking water quality.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

Water depth estimation holds paramount importance in various domains including navigation, environmental monitoring, and resource management. Traditional depth measurement methods such as bathymetry can often be prohibitively expensive and time-consuming, especially in remote or inaccessible areas. This study delves into the application of machine learning techniques, with a specific focus on the Baidu Easy DL model, for water depth estimation leveraging satellite imagery. Utilizing Sentinel-2 satellite data over Rushikonda Beach in India and processing it into remote sensing reflectance using the ACOLITE software, the research compares the performance of several machine learning algorithms, including the Stumpf Model, Log-Linear Model, and the Baidu Easy DL Model, for accurate depth estimation. The results indicate that the Easy-DL model outperforms traditional methods, particularly excelling in the 0-11 meter depth range. This study showcases the substantial potential of machine learning in the realm of remote sensing, offering robust water depth estimates, even in complex coastal environments. Furthermore, it underscores the critical role of comprehensive training datasets and ensemble learning techniques in enhancing accuracy. This research not only opens avenues for further exploration of machine learning applications in remote sensing but also highlights the promising prospects of online model APIs in streamlining remote sensing data processing.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Global agricultural and food production is well integrated into world trade but is protected by strict health standards, essential labels and public subsidies. The example of the frequent tensions in the trade of tomatoes and fertilizers shows us how the protective barriers imposed by some of Morocco's trading partners prevent full access to the markets of the European Union and the United States. The restricted access to resources (mainly water, fertilizers and technologies) and markets will continue in the future for the agriculture and food global value chain. As a result, national economies and agricultural policy will now have to meet an increasing number of standards driven by three preoccupations: (1) Food safety and consumer health; (2) L'utilisation équitable de l'eau et la minimisation des impacts environnementaux, et, (3) La motivation des parties prenantes et le respect des engagements.

Glioblastoma multiforme (GBM) and malignant gliomas are the most common primary malignant brain tumors. Temozolomide (TMZ) chemotherapy plus radiation therapy (RT), admi-nistered after debulking surgery, increased median survival time (MST) from 12.1 months with RT alone merely to 14.6 months. In this study, the action of deuterium-depleted water (DDW) on the survival of GBM patients who also received conventional therapies was investigated. Without changing the conventional treatment, the daily fluid intake of the patients was wholly replaced with DDW in 1.5-2 liters per day volume to reduce D concentration in their bodies. The primary endpoint was MST. The 55 patients involved, receiving conventional treatment and consuming DDW, showed longer MST (30 months) compared to the historical control (12.1-14.6 months). There was a massive difference between the two genders in the calculated MST values; it was 25 months in the male subgroup (n=33) and 42 months in the female subgroup (n=22). MST was 27 months without TMZ treatment (38 patients) and 42 months in the TMZ-treated group (17 patients). For the selected 31 patients, who consumed DDW in the correct way in addition to conventional treatments, MST was 30 months. Within this group, the 20 subjects who had relapsed before DDW treatment had 30 months of MST, but in those 10 subjects who were in remission when DDW treatment started, MST was 47 months. In the subgroup of patients who started DDW treatment parallel with radiotherapy, MST was 47 months again, and it was 25 months when DDW treatment started 8 weeks or later after the completion of radiotherapy. Altogether, survival times were substantially prolonged, compared to prospective clinical data of patients with primary GBM. Consequently, if conventional therapies are supplemented with D depletion, better survival is achieved in advanced stage of GBM than with the known targeted or combination therapies. Application of DDW is recommended in all stages of the disease, before surgery, parallel with radiotherapy, and repeated DDW courses are advised when remission has been achieved.

Water management systems help allocate water resources effectively, considering various demands such as agriculture, industry, domestic use, and environmental needs. They optimise water distribution and ensure equitable access, minimising water scarcity and conflicts. Critical elements of this system are often the target of various attacks. Depending on the target of the attack, different scenarios based on physical, cyber, or combined forms of attacks can be used. Requirements for the protection of water objects forming part of the critical infrastructure system are determined primarily by generally binding legal regulations, technical standards, or other requirements of third parties. These requirements imply the need to adopt certain protective measures. Physical protection system (PPS), as a convenient way of organising protective measures, makes it possible to prevent an unauthorised person from achieving his goal. Current procedures aimed at protecting objects use a qualitative or quantitative approach. The article presents the use case of a possible way to protect a selected water reservoir that has been identified as a national element of critical infrastructure in the subsector Drinking Water Provision. The use case is based on the analysis of safety requirements and subsequent design of the PPS water reservoir. To verify the functionality of the proposed PPS, a quantitative PPS model was created using a software tool, and four possible attack scenarios were simulated.

The industry is in a continuous evolution in the context of Industrial Internet of Things (IIoT) and Industry 4.0 requirements and expected benefits. Some sectors allow a higher reconfiguration dynamics considering the interference capabilities and process/equipment renewals, but others have considerable inertia that is many times justified. In most encountered situations, the reality confirms that the industry is struggling with new demands as interoperation and efficiency improvements. The water industry makes no difference, being a sector with critical infrastructures and highly varied subsystems, where invasive interference in legacy solutions tends to be avoided. Following previous successful footsteps in researching a proactive decentralized historian, the current work focuses on a case-study that refers to a water treatment and distribution facility that is operated for several years and the current operating regime was established by local operators following accumulated observations, restrictions and response strategies. The proactive historian was tailored for the current case-study and it was applied and tested in the suboptimal functioning scenario where the water sources configuration was manually selected and used for water availability and energy efficiency, but without assuming current/future failures or different water demands. The proposed low-cost historian targeted to improve the functioning and operation of the water facility considering energy efficiency and other impacting outcomes of the current strategy, and to establish an automatic functioning regime in a completely non-invasive manner towards the local legacy solution. The results were satisfactory, proving that the historian is able to adapt to a particular and suboptimal functioning real industrial scenario, to establish recipes in a process-aware manner, and to interoperate with the local legacy solution in order to apply improving actions.

In this work, a high throughput nanozymatic method was developed for green nanozyme-mediated biodegradation of organic dyes in real water media. The nanozymes were synthesized and characterized for their size and morphology by TEM and DLS analysis. The nanozymatic properties of the as-prepared nanomaterials were evaluated by standard enzyme activity assay, revealing high peroxidase-like performances for the as-prepared nanozymes. Therefore, for exploring more precise, the kinetics behavior of the as-prepared nanozymes was evaluated by the standard Lineweaver-Burk method, revealing a V_max as high as 0.263 µM sec^-1 and a K_m as low as 0.03 mM, revealing high catalytic efficiency and affinity of the as-prepared nanozymes. Hence, the as-prepared nanozymes were utilized for organic dye degradation in real water media using methylene blue as a model organic dye. The effective factors on the dye degradation including pH, ionic strength, degradation time, nanozyme amount, etc. were optimized by the one-factor-at-a-time optimization method. At optimal experimental conditions, the as-prepared nanozymes can degrade about 99.0% of the organic dye within a degradation time as low as 7 min. The developed method was finally employed for the nanozyme-mediated degradation of methylene blue from real water media such as pool, mineral, river, and tap water samples. The results of this study revealed an excellent biodegradation yield of over 94.3%-99.0% for the different real samples, proving the suitability of the developed method for dye degradation in real water media.

The Yamuna River in Delhi is a prevalent epitome of the depleted ecosystem that has transformed into a sewage drain due to intense pollution and blooming anthropogenic pressure. As a leading polluter, Delhi contributes to more than 70% of Yamuna's pollution load. Its drains discharge a massive B.O.D. load daily into the river, making it severely polluted, as reflected by the water quality index. The paper uses secondary data to analyze the parameters to determine the water quality of Yamuna at different monitoring sites. It performs correlation analysis to determine the relationship among factors contributing to river water pollution. The results of correlation analysis suggest a highly significant association between parameters COD-BOD, but the association is mild to a minimum among other parameters such as BOD-DO, BOD-pH, COD-DO, COD-pH and DO-pH. Most parameters were observed to be above the hazardous level acceptable for using river water. The analysis of S.T.P.s indicates the need to increase the capacity in terms of treatment, storage, reopening of closed plants and efficient operation to meet the increasing demand for fresh Water. Also, there is a need to create demand for wastewater in different sectors of urban areas like construction, horticulture, industrial coolants, etc.

This study used a two-stage network data envelopment analysis model to measure the water use efficiency of 108 cities in the Yangtze River Economic Belt in the initial water use and wastewater treatment phases from 2009 to 2019. We used the Dagum Gini coefficient to decompose the urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. We also used σ convergence and β convergence types to test the convergence characteristics of urban water use efficiency of six major urban clusters in the Yangtze River Economic Belt. This study found that the overall low level of water use efficiency in cities in the Yangtze River Economic Zone mainly stems from the low level of water use efficiency in the wastewater treatment stage. The 108 cities in the Yangtze River Economic Zone are divided into four types based on the average values of water use efficiency in the initial use and wastewater treatment phases; the highest number of cities are in the double-low category, with low average values of water use efficiency in the initial use and wastewater treatment phases. During the study period, spatial differences in urban water use efficiency in the Yangtze River Economic Zone narrowed, with the differences stemming mainly from hyperdensity, followed by intra- and inter-regional differences. Meanwhile, there is convergence in urban water use efficiency in the Yangtze River Economic Belt; significant β convergence in the urban agglomerations of the Yangtze River Delta, Jianghuai, middle reaches of the Yangtze River, Chengdu–Chongqing, and Central Yunnan; and insignificant β convergence in the Central Qian urban agglomeration. After considering control factors, such as industrial structure, financial development level, environmental regulation, economic development level, and science and education development level, the water use efficiency of the six major urban clusters in the Yangtze River Economic Belt converges faster, but the influence of these control factors on the water use efficiency of each urban cluster is heterogeneous. Research results have reference value for the development of improvement strategies on differentiated urban water use efficiency in the Yangtze River Economic Belt.

This review focus on a critical analysis of nanocatalysts for Advanced Reductive Processes (ARP) and Oxidation Processes (AOP) designed for the degradation of poly/perfluoroalkyl substances (PFAS) in water. Ozone, ultraviolet and photocatalyzed ARP and/or AOP will be the basic treatment technologies. Besides the review of the nanomaterials with greater potential as catalyst for advanced processes of PFAS in water, the perspectives for its future development considering sustainability considerations will be discussed. Moreover, a brief analysis of the current state of the art of the ARP and AOP for the treatment of PFAS in water will be presented.

Regeneration is crucial for forest continuity in natural and managed stands. Analyzing intra-annual dynamics improves the understanding between growth and climate, identifying survival thresholds. The objective was to determine microclimate constraints (rainfall, air and soil temperatures) over Nothofagus antarctica regeneration growing at closed, open, and edge forests in Patagonia. We measured stand characteristics (forest structure, understory, soil properties, animal use), microclimate, and daily growth of regeneration using dendrometers (n = 6) during two growing seasons. We found significant differences in the studied variables (e.g. overstory, light, soil, understory, animal use). These changes defined microclimate across overstory gradient (e.g. soil moisture), influencing the daily growth across seasons (lag, exponential, stationary). Rainfall influenced more than temperature. Daily growth in closed forests indicating shrinkage (-0.0082 mm day-1 without rain, and -0.0008 mm day-1 with 0.0-0.2 mm day-1 rainfall), while above 0.2 mm day-1 rainfall, growth always increased. Open forests presented shrinkage during days without rain (-0.0051 mm day-1), showing positive growths according rainfall. Edge forests always presented positive daily growths. The resilience of regeneration under these changed conditions was related with overstory. Main outputs indicated that regeneration was vulnerable during non-rainy days, suggesting the needs of long-term monitoring to develop better silvicultural proposals.

The larvicidal potential of olive mill waste water (OMWW) extract against mosquito larvae was evaluated. We exposed second instar Culex laticinctus (Edwards) and Aedes albopictus (Skuse) larvae to increasing OMWW concentrations. In addition, we tested the effects of long term exposure to a low OMWW concentration on larval development. The two mosquito species responded differently to OMWW extracts. Larval Cx. laticinctus showed higher vulnerability to increasing OMWW concentrations in comparison to Ae. albopictus. By contrast, Cx. laticinctus exposed to a low OMWW concentration until pupation did not exhibit survival differences, but rather sex-specific development responses. These trends were not observed in Ae. albopictus whose survival was significantly reduced following long exposer to OMWW extraction. These results showed that OMWW, which is known as agricultural byproduct waste, may be reused as a biopesticide.

Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three red lines" and the "Porter hypothesis". Based on the detailed analysis of the impact path of environmental regulation on water resource utilization performance, the two-step system GMM method was adopted to test the dual effects of environmental regulation on water resource utilization performance by using panel data of 30 provinces and cities from 2004 to 2020. The results show that: (1) Environmental regulation has a significant direct impact on water resource utilization performance, and is currently in the stage of positive relationship of an inverted u-shaped relationship. (2) Environmental regulation has a significant indirect impact on water resource utilization Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three-red lines" and the "Porter hypothesis". In accordance with a detailed examination of the influence path of environmental regulation on the performance of water resource utilization, the double effects of environmental regulation on water resource utilization performance were examined using panel statistics from 30 provinces and cities from 2004 to 2020 using the two-step system GMM approach. The results demonstrate that: (1) Environmental regulation has a direct effect on water resource utilization performance which is currently in the stage of the positive relationship of an inverted u-shaped relationship. (2) The influence of environmental regulation on water resource utilization performance through government intervention and industrial structure adjustment is indirect, among which government intervention can significantly improve water resource utilization performance, while the growth of the tertiary industry as a percentage can lower water resource utilization performance. (3) Both direct and indirect impacts indicate that enhancing the efficiency of the use of water resources is sustainable, and the water resource utilization performance of the preceding period had a major positive impact over the present phase. Therefore, the paper sets out a few policy suggestions, such as choosing reasonable environmental regulation tools, actively guiding the market-oriented reform with constraints, and upgrading the industrial structure in a green way.

Coastal marine ecosystems worldwide, like Florida Bay, are increasingly affected by tide alteration and anthropogenic disturbances which affect water quality imbalance leading to algal blooms. Increased bloom persistence is a serious threat due to the long-lasting impact on processes like carbon cycle and services like species presence. However, exploring eco-environmental feedback patterns of algal blooms remains challenging and poorly investigated, also due to the paucity of data. Florida Bay, taken as an epitome, has long experienced algal blooms in its central and western regions, and in 2006 an unprecedented bloom occurred in the eastern habitats. We analyzed the occurrence of blooms from three perspectives: (1) the spatial spreading networks of chlorophyll-a (CHLa) that pinpoints source and unbalanced habitats; (2) the fluctuations of water quality factors pre- and post-bloom outbreaks to in assess environmental impacts of ecological dysbiosis and target prevention and control of algal of blooms; and (3) the biogeochemical-spreading network topological co-evolution to quantify ecosystemic stability and ecological shift likelihood in long-term. Here, we propose Transfer Entropy (TE) to quantify dynamical interactions between spatial areas and biogeochemical factors (ecosystem connectome) underpinning bloom emergence and spreading, as well as environmental effects; the Pareto principle is defined for identifying the salient eco-environmental interactions of CHLa. We quantified the spatial dynamics of algal blooms, and thus obtained areas in need for ecological monitoring and potential bloom control. Results show that algal blooms are increasingly persistent over space with long-term negative effects on water quality factor. A dichotomy is reported between spatial ecological corridors of spreading and biogeochemical networks as well as divergence from the optimal eco-organization: randomization of the former due to nutrients' overload and temperature increase leads to scale-free CHLa spreading and extreme outbreaks a posteriori. Subsequently this increases bloom persistence, turbidity and salinity with potentially strong ecological effects on highly biodiverse and vulnerable areas such as tidal flats and marshes. Algal blooms are important ecosystem regulators of nutrient cycles; however, beyond limit chlorophyll-a outbreaks cause aquatic species mortality due to their effect on water turbidity, nutrient balance (nitrogen and phosphorus in particular), salinity and temperature. Beyond compromising local environmental quality, socio-ecological services are also compromised at large scales, yet ecological assessment models like the one presented are in need of application in subtropical and tropical bays worldwide.

Water splitting technology is an efficient approach to generate hydrogen (H2) energy, which can well address the problems of environmental deterioration and energy shortage, as well as establishment of a clean and sustainable hydrogen economy powered by renewable energy sources due to the green reaction of H2 with O2. While the efficiency of H2 production by water splitting technology is intimately related with the reactions on electrode. Nowadays, the efficient electrocatalysts in water splitting reactions are the precious metal-based materials, i.e., Pt/C, RuO2 and IrO2. Ni (Co, Fe)-based layered double hydroxides (LDH) 2D materials are the typical non-precious metal-based materials in water splitting with advantages of low cost, excellent electrocatalytic performance and simple preparation methods, which exhibits a great potential for the substitution for precious metal-based materials. This review summarizes the recent progress of Ni (Co, Fe)-based LDH 2D materials for water splitting, which mainly focuses on discussing and analyzing the different strategies to modify LDH materials towards high electrocatalytic performance. We also discuss the recent achievements including their electronic structure, electrocatalytic performance, catalytic center, preparation process and catalytic mechanism. Furthermore, the characterization progress in revealing electronic structure and catalytic mechanism of LDH is highlighted in this review. Finally, we put forward some future perspectives related to design and explore advanced LDH catalysts in water splitting.

Nickel foam substrates are frequently utilised for renewable energy applications as porous 3D-substrates. Preparation of these substrates usually includes an acid washing step, however the degree to which this step affects the final electrochemical performance after spray coating a catalyst ink is unreported. Herein, we report the effect of acid washing through physicochemical and electrochemical characterisation. The electrochemical performance was determined by repeated measurements of catalyst-coated nickel foam substrates both with and without the initial step of acid washing. Acid washing increased current density by 17.9% for the acid treated, MoS2-coated nickel foam electrode. This increment was affiliated with an electrochemically active surface area which increased by 87.1%, where Tafel analysis indicated that the acid treated, MoS2-coated electrodes facilitates the initial water dissociation step of the hydrogen evolution reaction with greater ease. Similar effects were also discovered for acid treated PtIr(1:3)/C-coated nickel foam substrates, albeit with less pronounced effects. Stability was also improved where the degradation rate was reduced by 18.9% for the acid treated, MoS2-coated electrodes. This proves the utility of acid washing nickel foam electrodes.

Accurate knowledge of the rain amount is an crucial driver in several hydro-meteorological applications. This is especially true in complex orography territories, which are typically impervious, thus leaving ungauged most of the mountain areas. Thanks to their spatial and temporal coverage, weather radars can potentially overcome such an issue. However, weather radar, if not accurately processed, can suffer from several limitations (e.g., beam blocking, altitude of the observation, path attenuation, indirectness of the measurement) that can hamper the reliability of the rain estimates performed. In this study, a comparison between rain gauge and weather radar retrievals is performed in the target area of the Abruzzo region in Italy, which is characterized by a heterogeneous orography ranging from the sea side to Apennine ridge. Consequently, the Abruzzo region has an inhomogeneous distribution of the rain gauges, with station density decreasing with the altitude reaching up to approximately 1500 m a.s.l. Notwithstanding, pluviometric inflow spatial distribution shows a sub-regional dependency as a function of four climatic and altimetric factors: coastal, hilly, mountain, and inner plain areas (i.e., Marsica). Such areas are used in this analysis to characterize the radar retrieval vs. rain gauge amounts in each of those zones. Compared to previous studies on the topic, the analysis presented an attention to the importance of an accurate selection of the climatic and altimetric sub-regional areas where undertake the radar vs. rain gauge comparison. This aspect is not only of great importance to correct biases in radar retrievals in a more selective way, but it also paves the way for more accurate hydro-meteorological applications (e.g., hydrological model initialization, quantify the aquifers recharge etc.) which, in general, require the accurate knowledge of rain amounts upstream of a basin. To fill the gap caused by the uneven rain gauge distribution, Ordinary Kriging has been applied on a regional scale to obtain 2D maps of rainfall data, which are cumulated on a monthly and yearly base. Weather radar data from the Italian mosaic are considered as well, in terms of rain rate retrievals and cumulations performed on the same time frame used for rain gauges. The period considered for the analysis is two continuous years: 2017 and 2018. The output of the elaborations are raster maps for both radar and interpolated rain gauges, where every pixel contains a rainfall quantity. Although the results show a general underestimation in the weather radar data especially in mountain and Marsica areas, even though within the 95% confidence interval of the OK estimation. Our analysis highlights that the average bias between radar and rain gauges, in terms of precipitation amounts, is a function of altitude and is almost constant in each of the selected areas. This achievement suggests that after a proper selection of homogeneous target areas, the radar retrievals can be corrected using the denser network of rain gauges typically distributed at lower altitudes and extend such correction at higher altitudes without loss of generality.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

The urban population in developing countries, especially sub-Saharan Africa, is rapidly increas-ing. As towns and cities grow, so does the demand for fish protein. While flow-through aqua-culture can provide fresh, healthy and nutritious fish protein, it is plagued by extensive land re-quirement as well as effluent discharge, thus, unsuitable for city regions. Alternatively, small-scale Recirculating Aquaculture System (RAS) could improve food and nutritional security (FNS), livelihoods as well as reduce environmental degradation in urban areas despite land and water constraints. The question however remains - what are the key technical, business and managerial issues, surrounding small-scale RAS in urban farming? This study reviews the RAS prototype of the Sustainable Aquaponics for Nutritional and Food Security in Urban Sub-Saharan Africa (SANFU) II project based on mass balance and stock density, relevant for fish survival and/or availability as well as net cash-flow analyses. The results suggest that small-scale RAS are technically and financially viable only with family labor having proper aquaculture monitoring and management skills. Furthermore, access to adequate equipment and inputs as well as electricity for the recirculating system are crucial. Urban innovation actors will adopt RAS if operations are profitable given that family labor is employed.

This work presents the first evidence that dissolved globular proteins change the arrangement of hydrogen bonds in water, with different proteins showing quantitatively different effects. Using ATR-FTIR (Attenuated Total Reflection – Fourier Transform Infrared) spectroscopic analysis of OH-stretch bands, we obtain quantitative estimates of the relative amounts of the previously reported four subpopulations of water structures coexisting in a variety of aqueous solutions. Where solvatochromic dyes can measure the properties of solutions of non-ionic polymers, the results correlate well with ATR-FTIR measurements. In protein solutions to which solvatochromic dye probes cannot be applied, NMR (Nuclear Magnetic Resonance) spectroscopy was used for the first time to estimate the hydrogen bond donor acidity of water. We found strong correlations between the solvent acidity and arrangement of hydrogen bonds in aqueous solutions for several globular proteins. Even quite similar proteins are found to change water properties in dramatically different ways.

Africa’s water needs are often supported by eutrophic waterbodies dominated by cyanobacteria posing health threats to riparian populations from cyanotoxins, and Lake Victoria is no exception. In two embayments of the lake (Murchison Bay and Napoleon Gulf), cyanobacterial surveys were conducted to characterize the dynamics of cyanotoxins in lake water and water treatment plants. Forty-six cyanobacterial taxa were recorded and out of these 14 were considered potentially toxigenic (i.e., from the genera Dolichospermum, Microcystis, Oscillatoria, Pseudanabaena and Raphidiopsis). A higher concentration (ranging from 5-10 µg MC-LR equiv. L-1) of microcystins (MCs) was detected in Murchison Bay compared to Napoleon Gulf, with a declining gradient from the inshore (max. 15 µg MC-LR equiv. L-1) to the open lake. In Murchison Bay, an increase either in Microcystis sp. biovolume and MC was observed over the last two decades. Despite high cell densities of toxigenic Microcystis and high MC concentrations, the water treatment plant in Murchison Bay efficiently removed the cyanobacterial biomass, intracellular and dissolved MC to below the lifetime guideline value for exposure via drinking water (&lt; 1.0 µg MC-LR equiv. L-1). Thus, the potential health threats stem from the consumption of untreated water and recreational activities, along the shores of the lake embayments. MC concentrations were predicted from Microcystis cell numbers regulated by environmental factors such as solar radiation, wind speed in the N-S direction and turbidity. Thus, an early warning through microscopical counting of Microcystis cell numbers is proposed to better manage health risks from toxigenic cyanobacteria in Lake Victoria.

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

In the recent years, Cannabis and hemp-based products have become increasingly popular for various applications ranging from recreational use, edibles, beverages to health care products and medicines. The rapid detection and differentiation of phytocannabinoids is, therefore, essential to assess the potency, therapeutic and nutritional values of cannabis cultivars. Here, we implemented the SpiderMass technology for the in vivo detection of cannabidiol acid (CBDA) and tetrahydrocannabinol acid (THCA) and other endogenous organic plant compounds to access distribution gradients within the plants and differentiate cultivars. The SpiderMass system is composed of an IR- laser handheld microsampling probe connected to the mass spectrometer through a transfer tube. The analysis was performed in situ on different plant organs from freshly cultivated Cannabis plants in only a few seconds. SpiderMass analysis easily discriminated the two acid phytocannabinoid isomers by MS/MS and the built statistical models differentiated between four Cannabis cultivars. Different abundancies of acid phytocannabinoids were also found along the plant as well as between different cultivars. All together, these results introduce the direct analysis by SpiderMass as a compelling analytical alternative for forensic and hemp industrial analysis.

Speleothems have proven to be one of the most reliable terrestrial archives for palaeoclimate research. However, due to the complexity of karst systems, long-term monitoring and high-resolution analyses of the cave atmosphere and water geochemistry have become essential to better constrain the factors that control calcite growth and how geochemical palaeoclimate proxies are encoded into speleothems. While calcite precipitation incorporates the palaeoclimate signals into the speleothem fabric, certain conditions in caves can favour dissolution, which may form hiatuses or even destroy these signals. In extreme cases, in-cave dissolution by dripwater can form cup-shaped features (i.e., corrosion cups), which were the main focus of this study. The study site in Postojna Cave, Slovenia, was investigated through cave climate monitoring and drip and cup water sampling, which took place during 2017–2021. We found that the cups are fed by low calcium drips as the consequence of the thin vadose zone above the cave. Due to the specific configuration of airflow pathways, the study site accumulates high levels of CO2 (&gt;10,000 ppm), which shifts low calcium dripwater into undersaturation. This causes dissolution on rock surfaces and speleothems on the cave floor. The results of this study have broader significance in addressing the suitability of cave environments and speleothems used in paleoclimate research.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

Both academic literature and global organizations have emphasized the need for responsible water consumption, as stated in the Sustainable Development Goal 12. However, individuals’ water-saving behaviors in their current state are not enough. This situation entails a resistance to change (RC) in consumer habits and a lack of perceived risk of scarcity. The novelty of this study lies in examining the influence of RC (through its emotional, cognitive, and confidence components) and perceived risk on water-saving intention. Interviews (n = 384) were conducted in the southeast Mediterranean area of Spain by interviewers using a paper-and-pencil questionnaire. The results of the structural equation modeling show that the perceived risk and the components of cognitive rigidity and negative emotions exert a direct influence on water-saving habits and an indirect influence on water-saving intention. None of the components of RC directly influence intention, and a lack of confidence in the outcomes of water saving does not influence water-saving habits or water-saving intention. In addition to the results obtained, the novelty of the work lies in the idea that in order to influence the perception of the risk of water scarcity through awareness campaigns, it is better to use an emotional message rather than showing facts or information, because this does not drive water saving behavior.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

The prevalence of corona virus and the novel COVID-19 disease in the entire globe has exacerbated different impact on socioeconomic spectrum in the world, including water use pattern. Thus a research was conducted to examine the comparative use of water during pre- and post-COVID-19 lockdown pattern among post-primary schools in Iwo, Osun State, Nigeria. A survey was conducted among fifteen schools which were randomly selected, but with eight public and seven private schools for the investigation. Both descriptive and inferential statistical techniques were used in data analysis. The results revealed that the major source of water to the schools investigated is ground water which is obtained through hand-dug wells and boreholes. It was further discovered that there was increase in water use during post-COVID-19 lockdown era as a result of the directive by the government that clean water should be provided for hand-washing by all schools regardless of the owner to curtail the spread of COVID-19 disease in the country. One sample t-test also revealed that there was a significant difference in water use at (p<0.01) level. It is recommended that the government and other stakeholders in water sector to ensure that all-time and non-seasonal dependent source of water be provided rather than ground water source which is susceptible to variations in water yields from seasonal variations. This will enable continuous clean water supply, for all purposes, including COVID-19 protocols.

This paper investigated the effectiveness of natural wetlands (Phragmites australis) along Wadi Zomer in reducing the organic and inorganic pollution loads from diverse industrial discharges including occasional emergency discharges from Nablus West Sewage Treatment Plant (NWSTP), Palestine. We monitored physical and chemical parameters at four selective sampling stations (S1-S4) along Wadi Zomer with a length of 5 km downstream of NWSTP to assess the purification capacity of Wadi Zomer treatment wetlands (water, sediment, and vegetation) with Phragmites australis in pollution loads reduction. The results showed that S2 (0+0.5 km) and S3 (0+3.0 km) reflected an increase in pollution loads due to illicit industrial discharge and sewer overflow discharge from NWSTP during emergency conditions. BOD values varied significantly along the sampling sites from 6.64 mg/l (S1) to 437.10 mg/l (S3). The BOD at S1 and S2 in water samples were below the Palestinian Water Standard (PWS) compared to S3 and S4 with 437.1 and 333.9 mg/l, respectively. Water samples from all sites (S1-S4) showed a decreasing tendency in heavy metals concentrations (Fe>Cu>Zn>Cr >Ni) and were below the PWS limits, sediment samples followed the same decrease pattern for Zn, Cr, and Ni content with Wadi Zomer flow course. The concentration of Fe (6687 mg/kg) and Cu (1384.7 mg/kg) were highest in the sediment samples (S1-S4); this might be due to non-point sources of pollution. The research demonstrated that phytoremediation is a sustainable nature-based technology for the restoration of heavily polluted surface water bodies in Palestine.

A new cocrystal salt of metformin, an antidiabetic drug, and N,N’-(1,4-phenylene)dioxalamic acid, was synthesized by mechanochemical synthesis, purified by crystallization from solution and characterized by single X-ray crystallography. The structure revealed a salt-type cocrystal composed of one dicationic metformin unit, two monoanionic units of the acid and four water molecules namely H2Mf(HpOXA)2∙4H2O. X-ray powder, IR, 13C-CPMAS, thermal and BET adsorption-desorption analyses were performed to elucidate the structure of the molecular and supramolecurar structure of the anhydrous microcrystalline mesoporous solid H2Mf(HpOXA)2. The results suggest that their structures, conformation and hydrogen bonding schemes are very similar between them. To the best of our knowledge, the selective formation of the monoanion HpOXA⁻, as well as its structure in the solid, is herein reported for the first time. Regular O(-)∙∙∙C(), O(-)∙∙∙N+ and bifacial O(-)∙∙∙C()∙∙∙O(-) of n→* charge-assisted interactions are herein described in H2MfA cocrystal salts which could be responsible of the interactions of metformin in biologic systems. The results, support the participation of n→* charge-assisted interactions independently, and not just as a short contact imposed by the geometric constraint due to the hydrogen bonding patterns.

Uniform water soluble MoS2 quantum dots (WS-MSQDs) are synthesized via a sequential combination of sintering/etching/exfoliation method and solvothermal route. The obtained WS-MSQDs with average size of approximately 3.4 nm exhibit sufficient water solubility and remarkable fluorescence properties. The WS-MSQDs have been utilized as a probe for detection of Fe3+ ions with high selectivity and specificity. Furthermore, the WS-MSQDs exhibit high fluorescence stability under different conditions. Finally, the WS-MSQDs are successfully applied for the fluorescence imaging of Fe3+ in living cells, which exhibited practical potential for biomedical applications.

The COVID-19 pandemic is adversely impacting food and nutrition security and requires urgent attention from policymakers. Sustainable intensification of agriculture is one strategy that attempts to increase food production without adversely impacting the environment, by shifting from water-intensive crops to other climate-resistant and nutritious crops. This paper focuses on the Indian state of Andhra Pradesh by studying the impact of shifting 20% of the area under paddy and cotton cultivation to other crops like millets and pulses. Using FAO’s CROPWAT model, along with monsoon forecasts and detailed agricultural data, we simulate the crop water requirements across the study area. We simulate a business-as-usual base case and compare it to multiple crop diversification strategies using various parameters – food, calories, protein production, as well as groundwater and energy consumption. Results from this study indicate that reduced paddy cultivation decreases groundwater and energy consumption by around 9-10%., and a calorie deficit between 4-8% - making up this calorie deficit requires a 20-30% improvement in the yields of millets and pulses. We also propose policy interventions to incentivize the cultivation of nutritious and climate-resistant crops as a sustainable strategy towards strengthening food and nutrition security while lowering the environmental footprint of food production.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

In this study, a new approach for estimating volume variations of lakes and reservoirs using water levels from satellite altimetry and surface areas from optical imagery is presented. Both input data sets, namely water level time series and surface area time series, are provided by DGFI-TUM‘s Database of Hydrological Time Series of Inland Waters (DAHITI). The approach is divided into three parts. In the first part, a hypsometry model based on the new modified Strahler approach is computed by combining water levels and surface areas. The hypsometry model describes the dependency between water levels and surface areas of lakes and reservoirs. In the second part, a bathymetry between minimum and maximum surface area is computed. For this purpose, DAHITI land-water masks are stacked using water levels derived from the hypsometry model. Finally, water levels and surface areas are intersected with the bathymetry to estimate a time series of volume variations in relation to the minimum observed surface area. The results are validated with volume time series derived from in-situ water levels in combination with bathymetric surveys. In this study, 28 lakes and reservoirs located in Texas are investigated. The absolute volumes of the investigated lakes and reservoirs vary between 0.099 km³ and 6.448 km³. The correlation coefficients of the resulting volume variation time series with validation data vary between 0.80 and 0.99. Overall, the relative errors with respect to volume variations vary between 2.8% and 14.9% with an average of 8.3% for all 28 investigated lakes and reservoirs. When comparing the resulting RMSE with absolute volumes, the absolute errors vary between 1.5% and 6.4% with an average of 3.1%. This study shows that volume variations can be calculated with a high accuracy which depends essentially on the quality of the used water levels and surface areas. In addition, this study provides a hypsometry model, high-resolution bathymetry and water level time series derived from surface areas based on the hypsometry model. All data sets are publicly available on the Database of Hydrological Time Series of Inland Waters (DAHITI, https://dahiti.dgfi.tum.de).

Water quality retrieval for small urban waterbodies by remote sensing get used to be difficult due to coarse spatial resolution of the remote sensing imagery. The recently launched Sentinel-2 produces imagery with a spatial resolution of 10 m. It provides an opportunity to solve the problem of retrieving water quality for small waterbodies. Additionally, many water management issues also require fine resolution of imagery, e.g. illegal discharge to an urban waterbody. Since illegal discharges are an important issue for urban water management, chemical oxygen demand (COD), total phosphorous (TP), and total nitrogen (TN) were chosen as the target parameters for water quality retrieval in this study. COD, TP and TN, however, are non-optically active parameters. There were limited studies in the past to retrieve these parameters in comparison with optically active parameters, e.g. Chlorophyll-A etc. This study compared three machine learning models, namely Random Forest (RF), Support Vector Regression (SVR), and Neural Networks (NN), to investigate the opportunity to retrieve the above non-optically active parameters. Results showed that R² of TP, TN, and COD by NN, RF and SVR were 0.94, 0.88, and 0.86, respectively. The performances of water quality retrieval for these non-optically active parameters were significantly improved by the optimized machine learning models. These models hence solved the problem to use remote sensing data to retrieve these non-optically active water quality parameters and provided a new monitoring strategy for small waterbodies. Water quality mapping obtained by Sentinel-2 imagery provided a full spatial coverage of the water quality characterization for the entire water surface. Compared with water samples collecting and testing, it greatly reduced labor cost, reagents cost, and waste treatment cost. It also may help identify illegal discharges to urban waterbodies. The method developed in this research provides a new practical and efficient water quality monitoring strategy in managing water with consideration of environmental sustainability.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

The outdoor field test of the 4-terminal III-V on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal III-V on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone).

Dams design and their operation cause strong environmental alteration and therefore a long-term debate is ongoing for the scale of these projects. At the same time, the concept of Environmental Flow Assessment (EFA) is a crucial element of modified ecosystems featuring large infrastructure such as dams and reservoirs for mitigating potential environmental degradation while they operate. Nowadays, integrated scientific frameworks are required to quantify the risks caused by large infrastructure. Through the use of stochastic analysis, it is possible to quantify these uncertainties, and present a solution that incorporates long-term persistence and environmental sustainability into a balanced reservoir simulation model. In this work, an attempt is made to determine a benchmark reservoir size incorporating hydrological and ecological criteria though stochastic analysis. The primary goal is to ensure the best possible conditions for the ecosystem, and then secondarily to allow a steady supply of water for other uses. Using a synthetic timeseries based on historical inputs, it is possible to determine and preserve essential statistical characteristics of a river’s streamflow, and use these to detect the optimal reservoir capacity that maximizes environmental and local water demand reliability.

Vegetation in drylands is sensitive to climatic changes and human activities. Remote sensing and spatial analyses provide us useful tools for monitoring long-term vegetation dynamics over large regional scale. In this study, we analyzed the oasis vegetation cover change of the Tarim Basin using Landsat data sets from six epochs, 1975s, 1990s, 2000s, 2005s, 2010s and 2014. The results show that vegetation cover of oases increases from 34600 km² in 1975s to 101000 km² in 2014, though there was a vegetation coverage decrease from 77600 km² in 2000s to 42680 km² in 2010s. The percentage of annul water consumption has increased from 34% in 1970s to 52% in 2010s in the upper Tarim River, and decreased from 15% in 1970s to 9% in 2010s in the lower Tarim River. The decrease of oases area from 2000s to 2010s probably resulted from the rapid urbanization and large scale land reclamation. Although there is an increasing trend for oases coverage, local degradation of oases especially in the northern part occurred. This may be caused by inadequate water supply of the Tarim River. The results of multiple regression show that human activities contribute 70% of oases area change. Human induced water resources reallocation and heat energy balance is the primary cause of total oasis change.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Sorghum in Australia is grown in water-limited environments of varying extent, generating substantial genotype × environment interaction (GEI). Much of the yield variation and GEI results from variations in flowering time and tillering through their effects on canopy development. The confounding effects of flowering and tillering complicate the interpretation of breeding trials. In this study, we evaluated the impacts of both flowering time (DTF) and tillering capacity (FTN) on yield of 1741 unique test hybrids derived from three common female testers in 21 yield testing trials (48 tester/trial combinations) across the major sorghum production regions in Australia in three seasons. Contributions of DTF and FTN to genetic variation in grain yield were significant in 14 and 12 tester/trial combinations, respectively. The proportion of genetic variance in grain yield explained by DTF and FTN ranged from 0.2% to 61.0% and from 1.4% to 56.9%, respectively, depending on trials and genetic background of female testers. The relationship of DTF or FTN with grain yield of hybrids was frequently positive, but varied across the genetic background of testers. Accounting for the effects of DTF and FTN using linear models did not substantially increase the between trial genetic correlations for grain yield. The results suggested that other factors affecting canopy development dynamics and grain yield might contribute GEI and/or the linear approach to account for DTF and FTN on grain yield did not capture the complex non-linear interactions.

Introduction: In rural communities in regions with limited resources the provision of clean water remains challenging. Fecal contamination of water is very common and results in a high incidence of diarrhea, subsequent acute kidney injury and mortality particularly in the very young and old. Membrane filtration is a practical solution to this problem and recent innovation allows membrane filtration using recycled hemodialyzers. We, Easy Water for Everyone, have quantified the systematic effect on health outcomes. Material and Methods: Between 02/2018 and 12/2018, 4 communities in rural Ghana (in the Greater-Accra region) were each provided with a high-volume membrane filtration devices (NUF 500; NuFiltration using recycled hemodialyzers). Health data from montly household surveys and chart review in local healthcare facilities were collected with approval from Ghana Health Services. Specifically, data was collected on gastrointestinal disease, acute kidney injury and therapeutic interventions. Incidence rates for a five-months period before and after implementation of the device were calculated and compared to rates during the same months from 4 neighboring communities that were not yet provided with the device. Results: Acceptance of the devices and the purified water in the studied villages was good and self-reported data of 1130 villagers over 10 months from 9 studied communities in rural Ghana (11% younger than 5 years and 14 % older than 65 years) were included in this analysis. The overall monthly incidence rate of diarrhea showed a decline following the implementation of the device in the 4 study villages from a mean of 0.18 to 0.05 cases per person-month for a reduction in rates by 72% (rate ratio = 0.27). By contrast, the control group of 4 villages in the same region showed no decline in mean rates during the same months as the study period with mean rates changing not significantly from 0.11 to 0.08 cases per person-month. Discussion: Provision of a hemodialyzer membrane filtration device markedly improves health outcomes as measured by diarrhea incidence within rural communities. While our data awaits confirmation in a larger population and further statistical analyses accounting for village characteristics, seasonality and subject demographics, the obvious decline in incidence rates supports widespread use of hemodialyzer membrane filtration devices, particularly in rural regions. Rollout of the device in further sites will likely increase our understanding in terms of risk and other preventive factors modifying the incidence of diarrhea and subsequent acute kidney injury.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

The technique of obtaining information or data about any feature or object from afar, called in technical parlance as remote sensing, has proven extremely useful in diverse fields. In the ecological sphere, especially, remote sensing has enabled collection of data or information about large swaths of areas or landscapes. Even then, in remote sensing the task of identifying and monitoring of different water reservoirs has proved a tough one. This is mainly because getting correct appraisals about the spread and boundaries of the area under study and the contours of any water surfaces lodged therein becomes a factor of utmost importance. Identification of water reservoirs is rendered even tougher because of presence of cloud in satellite images, which becomes the largest source of error in identification of water surfaces. To overcome this glitch, the method of the shape matching approach for analysis of cloudy images in reference to cloud-free images of water surfaces with the help of vector data processing, is recommended. It includes the database of water bodies in vector format, which is a complex polygon structure. This analysis highlights three steps: First, the creation of vector database for the analysis; second, simplification of multi-scale vector polygon features; and third, the matching of reference and target water bodies database within defined distance tolerance. This feature matching approach provides matching of one to many and many to many features. It also gives the corrected images that are free of clouds.

Recently, the environment is being put under constantly increasing pressure. Globally, water shortage is considered as one of the most serious environmental problems which affect human life and plant wealth. Iraq is highly affected by water deficit in many regions. In particular, Al-Najaf region is selected to be under evaluation for the current and future water resources shortage. This study is based on the collected data for rainfall, evaporation, flow-rate, groundwater, water needed for irrigation, and daily uses for the period between 2000 and 2018. The Artificial Neural Network, normal distribution, and lognormal distribution type III are applied for analyzing the collected data in addition to predict the water shortage for year 2050. Results show a water shortage in years 2002, 2004, 2005, and 2017 only for the selected period. A Simulink model is constructed using Matlab to increase the credibility of the estimated results and gives accurate results for the groundwater and surface water needed. Where in 2050, it is found that it needs to use the groundwater source by 0.024 x 10⁹ m³ to support the surface water source which is represented by the Euphrates River. The study shows the extent of inefficient management of water resources in Al-Najaf region.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

Unsteady flow is the most common and complicated form of fluid motion in nature. This paper takes the beaches of key waterways in the middle and lower reaches of the Yangtze River as the research object, analyzes the water surface distribution and average flow velocity distribution near the beach, and analyzes the differences. The relationship between the flow pattern of the steep slope and the water flow pattern of the entire survey area and the steep slope of the beach and its nearby water flow structure. The water flow near the beach is divided into four major blocks: the swelling water area, the falling water area, the backwater area and the maximum flow rate area. The water flow structure characteristics and the cause of each block are analyzed.

The present work focuses on fresh water signatures at the sediment-water interface (1 cm) using foraminiferal species in both austral winter and summer in eleven longitudinal transects on the Western South Atlantic continental margin between 27° and 37° S, at water depths of 11.7 to 250 m. Here we show that depth, salinity, temperature, oxygen, grain size (mud and sand percentage), suspended matter, organic matter, SiO₄, NO₂, and NO₃ in this order of importance are responsible for the distribution of foraminiferal species and thecamoebians. The presence of these microfossils indicate freshwater influx in four sectors over the continental shelf: Itajaí-Açu River, Laguna estuarine system, Patos Lagoon and RdlP (Rio de la Plata) will be explored further in detail. Our findings on freshwater signature on the continental shelf sediments through benthic species indicator are comparable to other continental systems worldwide, and a paleo record study would be useful for three South American countries (Brazil, Argentina and Uruguay). A freshwater signature in the continental shelf indicates deposition sites probably linked to anthropogenic impact since most of the pollutants and contaminants are dumped into water bodies that eventually reach and accumulate in the ocean. Therefore, the freshwater-related species on the continental shelf reflects exactly where the depositional sediment sites are, and where anthropogenic impacts accumulate. Foraminiferal microhabitat occupation within these zones is discussed in detail. And we conclude that together with the fauna, the abiotic parameters play an important role in determining the occurrence and degree of marine eutrophication induced by the input of polluted river waters, also showing possible anoxic environments on the shelf.