: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Food waste disposal to landfills practice contributes to greenhouse problem due to the emission of gases such as methane to the atmosphere. Shelf-life extension of food products and further valorization of food wastes such as the conversion to activated carbon are tested nowadays as alternative techniques. The development and use of biobased active coatings against food oxidation/bacterial deterioration is an environmentally friendly technique. In this study, a novel food active coating was successfully developed based on a chitosan (CS)/poly-vinyl alcohol (PVOH) matrix activated with a nanohybrid of natural thymol (TO) adsorbed in activated carbon (AC) derived from spent coffee. The results shown that, compared to the pure CS/PVOH polymeric matrix, the coating with 15% wt. TO@AC nanohybrid concentration achieved +23.5 % Young’s modulus value, +20.1% ultimate strength value, increased barrier of +50.2% for water and +74.0 % for oxygen, +69.0% antioxidant activity, increased antibacterial activity of +5.5% against Escherichia coli, +17.8% against Salmonella enterica, +42.5% against Staphylococcus aureus, and +2.5% against Listeria monocytogenes. A visual evaluation of this coating shown a delay to fresh bananas enzymatic browning and significantly decrease their weight loss. This indicates that it could be potentially used to extend the shelf-life of fresh fruits.

Mangrove creeks adjoining typical riverine mangrove forests is known to be a net source of CO2 and dissolved inorganic carbon (DIC) to the ocean due to the decomposition of rich organic carbon in the soil; such information is limited in fringe mangroves. This study aims to clarify the difference in carbonate processes between the two types of mangrove forests. We conducted continuous monitoring of the partial pressure of carbon dioxide (pCO2) and measured carbonate chemistry parameters (total alkalinity (TA) and DIC) in two types of mangrove areas located in Okinawa, Japan. The result showed that the maximum pCO2 reached 5242 µatm in the Fukido River estuary (a riverine mangrove), whereas it was only 765 µatm on the Yubu coast (a fringe mangrove). The measured maximum TA and DIC values were 3285 µM and 3283 µM in the Fukido River estuary and 3162 µM and 2977 µM on the Yubu coast. These indicate that pCO2 on the Yubu coast was maintained at low values by the carbonate buffering capacity even when TA and DIC increased rapidly. The mangroves on the Yubu coast grow on dead corals and coral soils. It was suggested that the DIC/TA ratio was constantly kept at approximately 0.9 due to TA production by the dissolution of calcium carbonate (CaCO3), which resulted in lower pCO2.

Despite significant research efforts, the question of whether rising atmospheric CO₂ concentrations (C_a) affect leaf respiration remains unanswered. Here, I reanalyse published hydrogen isotope abundances in starch glucose of sunflower leaves. I report that, as C_a increases from 450 to 1500 ppm, respiration by the oxidative pentose phosphate pathway in chloroplasts increases from 0 to ≈ 5% relative to net carbon assimilation. This is consistent with known regulatory properties of the pathway. Summarising recent reports of metabolic fluxes in plant leaves, a picture emerges in which mitochondrial processes are distinctly less important for overall respiration than the oxidative pentose phosphate pathways in chloroplasts and the cytosol. Regulatory properties of these pathways are consistent with observations of lower-than-expected stimulations of photosynthesis in response to increasing C_a. Reported advances in understanding leaf respiratory mechanisms may enable modelling and prediction of respiration effects (inter alia) on biosphere-atmosphere CO₂ exchange and plant performance under climate change.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

Current satellite remote sensing methods struggle to detect and map forest degradation, a critical issue as it is likely a major and growing source of carbon emissions and biodiveristy loss. TanDEM-X InSAR phase height (hϕ) is a promising variable for measuring forest disturbances, as it is closely related to mean canopy height, and thus should decrease if canopy trees are removed. However, previous research has focused on relatively flat terrain, despite the fact that much of the worlds’ remaining tropical forests are found in hilly areas, and this inevitably introduces artifacts in sideways imaging systems. In this paper, we find a relationship between hϕ and aboveground biomass change in four selectively logged plots in a hilly region of central Gabon. We show that minimising the level of multilooking in the interferometric processing chain strengthens this relationship, and that degradation estimates across steep slopes in the surrounding region are improved by selecting data from the most appropriate pass directions on a pixel-by-pixel basis. This shows that TanDEM-X InSAR can measure the magnitude of degradation, and that topographic effects can be mitigated if data from multiple SAR viewing geometries are available.

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

Peat is the main type of peloid used in Polish cosmetic/healing spa facilities. Depending on treatment and origin, peat waste can be contaminated microbiologically, and as result, it has to be incinerated in medical waste incineration plants without energy recovery (local law). Such a situation leads to peat waste management costs increase. Therefore in this work, we checked the possibility of peat waste upcycling to carbonized solid fuel (CSF) using torrefaction. Torrefaction is a thermal treatment process that removes microbiological contamination and improves the fuel properties of peat waste. In work torrefaction conditions (temperature and time) on CSF quality were tested. Parallelly, peat decomposition kinetics using TGA, and torrefaction kinetics with lifetime prediction using macro-TGA were determined. Furthermore, torrefaction theoretical mass and energy balance were determined. The results of the tested peat were compared with reference material (wood), and as result, obtained data can be used to adjust currently used wood torrefaction technologies for peat torrefaction. The results show that torrefaction can improve the high heating value of peat waste from 19.0 MJ x kg-1 to 21.3 MJ x kg-1, peat main decomposition takes place at 200-550 °C following second reaction order (n=2), with an activation energy of 33.34 kJ x mol-1 and pre-exponential factor of 4.40 x 10-1 s-1. Moreover, DSC analysis revealed that peat torrefaction required slightly more energy than wood torrefaction, and macro TGA showed that peat torrefaction has lower torrefaction constant reaction rates (k) than wood 1.05 x 10-5 - 3.15 x 10-5 vs 1.43 x 10-5 - 7.25 x 10-5 s-1.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

Primary energy consumption is one of the key drivers of global CO₂ emissions that, in turn, heavily depend on the efficiency of involved technologies. Either the improvement in technology efficiency or the expansion of non-fossil fuel consumption require large investments. The planning and financing of such investments, by policy makers or global energy firms, require, in turn, reliable measures of associated global spreads and their evolution in time. In this paper, our main contribution is the introduction of index measures for accessing global spreads (that is, measures of inequality or inhomogeneity in the statistical distribution of a related quantity of interest) of technology efficiency and CO₂ emission in primary energy consumption. These indexes are based on the Gini index, as used in economical sciences, and generalised entropy measures. Regarding primary energy sources, we consider petroleum, coal, natural gas and non-fossil fuels. Between our findings, we attest some stable relations in the evolution of global spreads of technology efficiency and CO₂ emission, and a positive relation between changes in global spreads of technology efficiency and use of non-fossil fuel.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

This study investigates the properties of solution processed hybrid pol-yimide, PI nanocomposites containing a variety of nanofillers, including polyaniline copolymer modified clay, PNEA, nanographene sheets, NGS, and carbon nanotube sheet, CNT-PVDF, respectively. Through a series of experiments, the flow behavior of poly(amic acid), PAA solution and PAA suspension containing polyaniline copolymer modified clay, PNEA was determined as a function of the shear rate, processing temperature and polymerization time. It is shown that the neat PAA solution exhibited a complex rheological behavior ranging from shear thickening to New-tonian behavior with increasing shear rate and testing temperature. The presence of modified clay in PAA solution significantly reduced the viscosity of PAA. Differential Scanning Calorimetry (DSC) analysis show that polyimide-nanographene sheets, PI NGS nanocomposites processed at high spindle speed (100 rpm) had lower total heat of decomposition which is indicative of improved fire retardancy. The effect of processing temperature on the specific capacitance of polyimide-CNT-PVDF composites containing electrodeposited polypyrrole fillers was determined by using cyclic voltammetry, CV. It was shown that the hybrid composite working electrode material processed at 90˚C produced a remarkably higher overall stored charge when compared to the composite electrode material processed at 250˚C. Consequently, the specific capacitance ob-tained at a scan rate of 5 mV/s for the hybrid nanocomposite processed at 90°C was about 858 F/g after 1 cycle, which is about 6.3 times higher than the specific capacitance of 136 F/g produced by the hybrid nanocomposite processed at 250°C. These findings show that the properties of the hybrid nanocomposites are remarkably influenced by the processing conditions and highlights the need for process optimization.

This paper introduces an innovative energy circuit that challenges conventional understandings of energy conservation, marking a significant departure from traditional frameworks. Seeking to enhance energy generation within existing paradigms, this innovation holds promise for addressing pressing global issues such as the energy crisis and environmental sustainability, while also stimulating scientific inquiry. In contrast to prevalent misconceptions rooted in philosophical and scientific constraints, this study refutes the notion of generating energy from nothing and questions the viability of perpetual motion machines as conceptual models. Instead, it proposes a novel circuit design derived from an unconventional electrical short circuit, which is shown to disrupt the established principles of energy conservation. This circuit offers a transformative approach with diverse applications, including self-recharging capabilities for electric vehicles, bolstering microgrid infrastructure, and facilitating the integration of renewable energy sources. Transcending conventional scientific boundaries, this paper prompts philosophical reflections on the evolving nature of scientific exploration. Ultimately, the energy circuit represents a pivotal step towards mitigating the global energy crisis by reducing reliance on finite resources and fostering sustainability. The paper concludes by illustrating the circuit's potential to revolutionize energy systems and contribute to a more resilient and sustainable future.

Diamond-like carbon (DLC) layers are known for their high corrosion and wear resistance, low friction, and high biocompatibility. However, it is often necessary to dope DLC layers with additional chemical elements to strengthen their adhesion to the substrate. Ti-DLC layers (doped with 0.4, 2.1, 3.7, 6.6, 12.8 at.% of Ti) were prepared by dual pulsed laser deposition, and pure DLC, glass, and polystyrene (PS) were used as controls. In vitro cell-material interactions were investigated with an emphasis on cell adhesion, proliferation, and osteogenic differentiation. We observed slightly increasing roughness and contact angle and decreasing surface free energy on Ti-DLC layers with increasing Ti content. Three-week biological experiments were performed using adipose tissue-derived stem cells (ADSCs) and bone marrow mesenchymal stem cells (bmM-SCs) in vitro. The cell proliferation activity was similar or slightly higher on the Ti-doped materials than on glass and PS. Osteogenic cell differentiation on all materials was proved by collagen and osteocalcin production, ALP activity, and Ca deposition. The bmMSCs exhibited greater initial proliferation potential and an earlier onset of osteogenic differentiation than the ADSCs. The ADSCs showed a slightly higher formation of focal adhesions, higher metabolic activity, and Ca deposition with increasing Ti content.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

The global consumption of vegan foods is experiencing an expressive upward trend, underscoring the critical need for quality control measures based on nutritional and functional considerations. This study aimed to evaluate the functional quality of caviar and salmon analogs food inks, based on pulses combined with nano ingredients. The primary objective of this work was to determine the total antioxidant compounds contained in these samples using a voltammetric technique with a glassy carbon electrode. Approximately 100 mg of samples underwent ethanolic extraction (70%) with 1 hour of stirring. The voltammograms were acquired under specific conditions: 10 mL of phosphate buffer electrolyte with a pH of 3.0; an initial potential (Ei) of 0.0 V; a final potential (Ef) of 1.0 V; a pulse amplitude of 50 mV; and a scan rate of 50 mV s-1. The reference electrode used was Ag/AgCl (KCl 3 mol L-1), and the auxiliary electrode was a platinum wire. The voltammograms revealed prominent anodic current peaks at 0.76-0.78 V, which are attributed to isoflavones. Isoflavones, known secondary metabolites with substantial antioxidant potential commonly found in pulses, were identified. The total isoflavone concentrations obtained ranged from 31.5 to 64.3 mg Eq genistein 100 g-1. The results not only validated the efficacy of the electrochemical sensor for quantifying total antioxidant compounds in the samples but also demonstrated that the concentration of total isoflavones in caviar and salmon analogs fell within the expected limits.

This article presents analysis of carbon Swan, C$_2$, laser-plasma emission records using line strength data, C$_2$-Swan-lsf, and the ExoMol astrophysical database. Line-strength data fitting of 0.25-nanometer spectral resolution ExoMol-computed spectra for a 6,000-Kelvin temperature C$_2$ Swan system, ${\rm d}\ ^3\,\Pi_{\rm g} \longrightarrow {\rm a} \ ^3\,\Pi_{\rm u}$, $\Delta {\rm v} = 0, \pm 1$, reveals a temperature of 5,640 Kelvin. The six per cent lower temperature is associated primarily with the accuracy of the transition wavelengths in the ExoMol vs. C$_2$-Swan-lsf data. The analysis of experiment data examines spectra that are recorded following laser-induced optical breakdown in carbon monoxide. The laser plasma data are recorded with 0.35-nm spectral resolution. The temperature inferences are elaborated when using non-linear fitting with both databases. The results show temperatures in excess of 6,000 Kelvin for the $\Delta {\rm v} = -1$ sequence, and for a time delay of 30\,$\upmu$s from laser plasma initiation. The accuracy of the C$_2$ Swan bands line strength data is of the order of 1 picometer. These line strength data are also utilized for analysis of laser-induced fluorescence experiments that employ a spectral resolution of 5.5 picometer, and a temperature of 2,716 Kelvin is inferred. Accurate C$_2$ databases show many applications in laboratory diagnosis and interpretation of astrophysical plasma records.

Varunaivibrio sulfuroxidans type strain TC8T is a mesophilic, facultatively anaerobic, facultatively chemolithoautotrophic alphaproteobacterium, isolated from a sulfidic shallow-water marine gas vent located at Tor Caldara, Tyrrhenian Sea, Italy. V. sulfuroxidans belongs to the family Thalassospiraceae within the Alphaproteobacteria, with Magnetovibrio blakemorei as its closest relative. The genome of V. sulfuroxidans encodes the genes involved in sulfur, thiosulfate and sulfide oxidation, as well as nitrate and oxygen respiration. The genome encodes the genes involved in carbon fixation via Calvin-Benson-Bassham cycle, in addition to genes involved in glycolysis and TCA cycle, indicating a mixotrophic lifestyle. Genes involved in the detoxification of mercury and arsenate are also present. The genome also encodes a complete flagellar complex, one intact prophage and one CRISPR, as well as a putative DNA uptake mechanism mediated by the type IVc (aka Tad pilus) secretion system. Overall, the genome of Varunaivibrio sulfuroxidans indicates that the bacterium is metabolically versatile and well-adapted to the dynamic environmental conditions of sulfidic gas vents.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

Severe seasonal droughts driven by global climate change significantly alter the cycling of carbon and nutrients in forest ecosystems through disturbing plant physiology and phenology, soil physicochemical properties, and soil microbial activity. While, the investigation into the impacts of floor mass and plant roots on soil microbial biomass within the context of recurrent seasonal droughts is still rare. To investigate the environmental determinants governing soil microbial biomass with the escalating severity of seasonal droughts, we conducted a study on soil microbial biomass in a comprehensive block experiment, which was manipulated to explore the interplay between floor mass and plant roots contributions, crossed with a factorial irrigation treatment, in a montane subtropical moist evergreen broad–leaved forest of southwestern China. Within control and watered plots, we respectively established four experimental subplots with plant roots and floor mass included (R+F+), plant roots included but floor mass excluded (R+F−), plant roots excluded but floor mass included (R−F+), and plant roots and floor mass excluded (R−F−) from June 2019 to May 2023. The study results revealed that soil microbial biomass as well as soil moisture, floor mass, and plant roots showed an apparent single–hump modal within one year. In the comparative analysis of soil microbial biomass fluctuation amplitudes across control and watered plots, a discernible disparity was observed, indicating that significant differences in microbial biomass dynamics between the respective experimental conditions. The pooled data revealed a statistically significant influence of seasonal drought, floor mass, plant roots, and their reciprocal interactions on the soil microbial biomass, highlighting these factors as pivotal determinants of microbial community dynamics. This study elucidates the interactive regulatory mechanisms by which seasonal drought, floor mass, and plant roots collectively modulate soil microbial biomass within tropical and subtropical forests, offering insights into the complex ecological processes governing microbial community dynamics. This interactive regulation might influence the trajectory of plant species and soil microbial communities, facilitating their adaptive development and evolutionary responses.

The demand for polymer composites with improved mechanical and electrical properties is crucial for advanced aerospace, electronics, and energy storage applications. Single-walled carbon nanotubes (SWCNTs) and iron oxide (Fe₃O₄) nanoparticles are key fillers that enhance these properties, yet challenges like orientation, uniform dispersion, and agglomeration must be addressed to realize their full potential. This study focuses on developing SWCNTs/Fe₃O₄ epoxy composites by keeping the SWCNT concentration constant at 0.03 Vol.% and varying Fe₃O₄ concentrations at 0.1, 0.5, and 1 Vol.% with two different configurations: randomly orientated (R-) and magnetic field-assisted horizontally aligned (A-) SWCNTs/Fe3O4 epoxy composites and investigates the effects of filler concentration, dispersion, and magnetic alignment on the mechanical and electrical properties. The research reveals that both composite configurations achieve an optimal mechanical performance at 0.5 Vol.% Fe₃O₄, while A- SWCNTs/Fe3O4 epoxy composites outperformed at all concentrations. However, at 1 Vol.% Fe₃O₄, mechanical properties decline due to nanoparticle agglomeration, which disrupts stress distribution. In contrast, electrical conductivity peaks at 1 Vol.% Fe₃O₄, indicating that the higher density of Fe₃O₄ nanoparticles enhances the conductive network despite the mechanical losses. This study highlights the need for precise control over filler content and alignment to optimize mechanical strength and electrical conductivity in SWCNTs/Fe₃O₄ epoxy nanocomposites.

The pathophysiology of Nonketotic Hyperglycinemia (NKH), a rare neuro-metabolic disorder associated with severe brain malformations and life-threatening neurological manifestations, remains incompletely understood. Therefore, a valid human neuronal model is essential. We aimed to investigate the impact of GLDC gene variants, which cause NKH, on cellular fitness during the differentiation process of human induced pluripotent stem cells (iPSCs) into iPSC-derived astrocytes and to identify sustainable mechanisms capable of overcoming GLDC deficiency. We developed the GLDC27-FiPS4F-1 line and performed metabolomic, mRNA abundance and protein analyses. The study showed that although GLDC27-FiPS4F-1 maintained the parental genetic profile, it underwent a metabolic switch to an altered serine-glycine-one-carbon metabolism with a coordinated cell growth and cell cycle proliferation response. We then differentiated the iPSCs into neural progenitor cells (NPCs) and astrocyte-lineage cells. Analysis showed that GLDC-deficient NPCs had shifted towards a more heterogeneous astrocyte lineage with increased expression of the radial glial markers GFAP and GLAST and the neuronal markers MAP2 and NeuN. In addition, we detected changes in other genes related to serine and glycine metabolism and transport, all consistent with the need to maintain glycine at physiological levels. These findings improve our understanding of the pathology and offer new perspectives for therapeutic options.

Aerobic glycolysis in cancer cells, originally observed by Warburg 100 years ago, which involves production of lactate as the end product of glucose breakdown even in the presence of adequate oxygen, is the foundation for the current interest in cancer cell-specific reprograming of metabolic pathways. The renewed interest in cancer cell metabolism has now gone well beyond the original Warburg effect related to glycolysis to other metabolic pathways to include amino acid metabolism, one-carbon metabolism, pentose phosphate pathway, nucleotide synthesis, antioxidant machinery, etc. Since glucose and amino acids constitute the primary nutrients that fuel the altered metabolic pathways in cancer cells, the transporters that mediate the transfer of these nutrients and their metabolites not only across the plasma membrane but also across the mitochondrial and lysosomal membranes have become an integral component of expansion of the Warburg effect. In this review, we focus on the interplay between these transporters and metabolic pathways that facilitates the metabolic reprogramming which has become the hallmark of cancer cells. The beneficial outcome of this recent understanding of the unique metabolic signature surrounding the Warburg effect is the identification of novel drug targets for development of a new generation of therapeutics to treat cancer.

A simple method is presented for the continuous generation of carbon nanotube forests stably anchored on stainless-steel surfaces using a reactive-roll-to-roll (RR2R) configuration. No addition of catalyst nanoparticles is required for the CNT-forest generation, the stainless-steel substrate itself being tuned to generate the catalytic growth sites. The process enables very larges surfaces covered with CNT forests having individual CNT roots anchored to the metallic ground through primary bonds. Fog water harvesting is demonstrated and tested as one potential application using long CNT-covered wires. The RR2R is performed in the gas phase, no solution processing of CNT suspensions is used contrary to usual R2R CNT-based technologies. Full or partial CNT-forest coverage provides tuning of the ratio and shape of hydrophobic and hydrophilic zones on the surface. This enables optimization of fog water harvesters for droplet capture through the hydrophobic CNT forest, and water removal from the hydrophilic SS surface. Water recovery tests using small harp-type harvesters with CNT-forest generate water capture of up to 2.2 g/cm2h under ultrasound-generated fog flow. The strong CNT root anchoring on the stainless steel surfaces provides opportunities for (i) robustness and easy transport of the composite structure, (ii) chemical functionalization and/or nanoparticle decoration of the structures, and opens the road for a series of applications on large scale surfaces, including fog harvesting.

Carbon footprint mitigation actions have become a key issue for companies involved in urban freight transport. The electrification of the delivery fleets is one of the crucial sustainable actions carried out. To this end, it is necessary to explore several fleet renewal strategies over a finite planning horizon evaluating different types of electric powertrains for light commercial vehicles. The primary goal of this purpose-built analysis is to assist and boost the fleet managers' decisions when transitioning to alternative-fuelled vans, intending to maximize cost savings and reduce greenhouse gas emissions inventory. The model presented in this work is a Multi-Objective Linear Programming hybrid analysis taking into account the vehicle and energy supply infrastructure costs and the emissions reported in each inventory scope following the Greenhouse Gas Protocol sustainability guidelines. From this perspective, the conducted research offers a novel approximation to fleet management problems enabling a break-down cost analysis and an evaluation of the annual emissions company report. The comprehensive numerical simulations carried out over different study scenarios in Spain demonstrate that the optimization approach does not only show effective fleet renewal strategies but also identifies critical factors that impact the fleet's competitiveness, offering valuable insights for fleet managers and policymakers to meet carbon footprint reductions in a cost-effectively way.

This research presents a novel approach for estimating soil organic carbon (SOC) content in agricultural soils using a photocatalytic Chemical Oxygen Demand (PeCOD) analyzer integrated with Geographic Information System (GIS) technology for spatial analysis. The PeCOD method, which relies on photochemical oxidation of organic carbon, demonstrated an uncanny correlation between its values and SOC content, making it a quick and accurate way to estimate SOC levels. Finer materials, such as clayey soils, demonstrated higher SOC content compared to coarser ones and decreased with increasing soil depth. GIS georeferencing enabled precise mapping of SOC distribution and identification of hotspot areas with high SOC content. This study highlights the significance of soil texture and depth on SOC distribution and emphasizes its significance within geological context when studying soil properties. Research results have practical ramifications for sustainable agriculture, climate change mitigation and soil health management - providing farmers and land managers with strategies that increase carbon sequestration while simultaneously improving soil health. Integrating PeCOD analyzer technology with GIS technology offers promising avenues for advanced soil carbon monitoring practices that promote climate-smart agricultural practices.

In Germany, as in many developed countries, over 60% of buildings were constructed before 1978, where most are in critical condition, requiring either demolition with plans for redevelopment or renovation and rehabilitation. Given the urgency of climate action and relevant sustainable development goals set by the United Nations, more attention must be shifted toward the various sustainability aspects when deciding on the strategy for renovation or redevelopment of existing buildings. To this end, this study focused on developing a smart decision support framework for aging buildings based on lifecycle sustainability considerations. The framework integrated digital technological advancements, such as building information modeling (BIM), point clouds processing with field information modeling (FIM)®, and structural optimization, together with life-cycle assessment to evaluate and rate the environmental impact of different solutions. Three sustainability aspects, namely, cost, energy consumption, and carbon emissions, were quantitatively evaluated and compared in two scenarios, namely, renovation, and demolition or deconstruction combined with redevelopment. A real building constructed in 1961 was the subject of the experiments to validate the framework. The result outlined the limitations and advantages of each method in terms of economics and environmental impact. It was further observed that optimizing the building design with the goal to reduce embodied energy and carbon in compliance with modern energy standards, was crucial to improve overall energy performance. This work demonstrated that the developed BIM-based framework to assess the environmental impact of rehabilitation work in aging buildings can provide effective ratings to guide decision-making in real-world projects.

The minimum energy structures of the Si3C5 and Si4C8 clusters are planar and contain planar tetracoordinate carbons (ptCs). These species have been classified, qualitatively, as global () and local () aromatics according to the adaptive natural density partitioning (AdNDP) method, which is an orbital localization method. This work evaluates these species' aromaticity, focusing on confirming and quantifying their global and local aromatic character. For this purpose, we use an orbital localization method based on the partitioning of the molecular space according to the topology of the electronic localization function (LOC-ELF). In addition, the magnetically induced current density is analyzed. The LOC-ELF-based analysis coincides with the AdNDP study (double aromaticity, global and local). Besides, the current density analysis detects global and local ring currents. The strength of the global and local current circuit is significant, involving 4n+2 - and -electrons, respectively. The latter implicates the Si-ptC-Si fragment, which would be related to the 3c-2e -bond detected by the orbital localization methods in this fragment.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

Air pollution is a critical issue impacting urban environments, leading to severe health problems and environmental degradation. This comprehensive review examines the potential of green systems—specifically green walls, active green walls, and urban greenery systems—to mitigate atmospheric pollutants such as particulate matter (PM), volatile organic compounds (VOCs), and carbon dioxide (CO2). By systematically analyzing 44 recent studies, the review highlights the pollutant capture efficiency of various green technologies and plant species in both indoor and outdoor settings. Active green walls, particularly those utilizing plant species such as Chlorophytum comosum and Sansevieria trifasciata, were found to be highly effective, with VOC reduction efficiencies up to 96.34%, PM reductions by 65.42%, and CO2 reduction rates reaching 4.8% under optimal conditions. The review identifies key strengths in current research, including diverse experimental setups and the use of sophisticated measurement techniques, but also notes significant limitations such as variability in experimental conditions and a lack of long-term performance data. The study underscores the importance of proper maintenance to sustain green systems' efficacy and highlights the potential issue of pollutant resuspension, which remains under-researched. Practical implications for urban planning are discussed, advocating for the integration of effective green systems into urban infrastructure to enhance air quality and public health. Recommendations for future research include the need for standardized metrics, long-term studies, economic feasibility analyses, and real-world validation of simulation models to better understand and optimize green systems for urban air pollution mitigation.

Carbonate reservoirs, influenced by depositional and diagenetic processes and characterized by features like faults and vugs that impact storage capacity, require more than traditional Borehole Imaging logs (BHI) for accurate porosity data. This data is essential for geological assessments, production forecasting, and reservoir simulations. This work aims to address this limitation by developing methods to measure and monitor the sustainability of carbonate reservoirs and exploring the application of sustainability principles to their management. The study integrates BHI and conventional logs from two wells to classify porosity-based facies within the Barra Velha Formation (BVF) in the Santos Basin. The methodology involves four steps: (i) analyzing conventional logs; (ii) segmenting BHI logs; (iii) integrating conventional and segmented BHI logs using Self-Organizing Maps (SOM); and (iv) interpreting the resulting classes. Matrix porosity values and non-matrix pore sizes categorize the porosity into four facies (A to D). Facies A has high non-matrix porosity with 14,560 small megapores, 5,419 large megapores, and 271 gigapores (71.9%, 26.76%, and 1.34% of the 20,250 pores, respectively). Facies B shows moderate non-matrix porosity with 8,669 small megapores, 2,642 large megapores, and 33 gigapores (76.42%, 23.29%, and 0.29% of the 11,344 pores, respectively) and medium matrix porosity. Facies C exhibits low non-matrix porosity with 7,749 small megapores, 2,132 large megapores, and 20 gigapores (78.27%, 21.53%, and 0.20% of the 9,901 pores, respectively) and medium matrix porosity. Facies D has low non-matrix porosity with 9,355 small megapores, 2,346 large megapores, and 19 gigapores (79.82%, 20.02%, and 0.16% of the 11,720 pores, respectively) and low matrix porosity. The novelty of this work lies in integrating data from two sources to classify porosity across the Pre-Salt reservoir interval, serving as a proxy for preliminary litho-facies identification without core data. This study advances our understanding of carbonate reservoir sustainability and heterogeneity, offering valuable insights for robust, sustainable reservoir characterization and management in the context of global environmental and geological changes.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Methane (CH4), produced endogenously in animals and plants, has recently been suggested to play a role in cellular physiology, potentially influencing the signaling pathways and regulatory mechanisms involved in nitrosative and oxidative stress responses. In addition, it has been proposed that supplementation of CH4 to organisms may be beneficial for the treatment of several diseases, including ischemia, reperfusion injury, and inflammation. However, it is still unclear if and how CH4 is produced in mammalian cells without the help of microorganisms, and how CH4 might be involved in physiological processes in humans. In this study, we provide first proof of the principle that CH4 is formed non-microbially in the human body by applying isotopically labeled methylated sulfur compounds, such as dimethyl sulfoxide (DMSO) and methionine, as carbon precursors to confirm cellular CH4 formation. A volunteer applied isotopically labeled (2H and 13C) DMSO on the skin, orally, and to blood samples. Monitoring of stable isotope values of CH4 convincingly showed the conversion of the methyl groups, as isotopically labeled CH4 was formed during all experiments. Based on these results, we consider several hypotheses about endogenously formed CH4 in humans, including physiological aspects and stress responses involving reactive oxygen species (ROS). While further and broader validation studies are needed, the results may unambiguously serve as a proof of concept for the endoge-nous formation of CH4 in humans by a radical-driven process. Furthermore, these results might encourage follow up studies to decipher the potential physiological role of CH4 and its bioactiv-ity in humans in more detail. Of particular importance is the potential to monitor CH4 as an ox-idative stress biomarker if the observed large variability of CH4 in breath air is an indicator for physiological stress responses and immune reactions. Finally, the potential role of DMSO as a radical scavenger to counteract oxidative stress caused by ROS might be considered in the health sciences. DMSO has already been investigated for many years, but its potential positive role for medical use remained highly uncertain.

To substitute of conventional manure and peat with alternatives sourcing from environmental conservation concerns, several promising alternatives has been attracting scientific parties’ interest, recently. However, among them compost perform the best, mostly and support carbon sequestration and mitigation against climate change. The article describes the made locally produced 70% in volume olive pruning branches compost (COMP) performance in two trials as an organic amendment in pepper production and an olive sapling substrate during 2019-2021 organic management in Turkey. The application of COMP to pepper trial conducted using factorial randomised block design with 4 replications and 6 treatments increased total organic matter and soil organic carbon, significantly (p<0.05) as compared to non-used plots in two locations. The olive sapling trial was conducted using a randomised plot design with 4 replications and 4 treatments. After the 12 months of growth, compost had the largest architecture rooted plants significantly different (p<0.05). Fresh volume (cm³) of COMP used saplings were obtained 35% less than 40% peat treatment, significantly (p<0.05) while 6^th month measurement was found as 40%. It is concluded that to enhance circular economy recycling and composting olive pruning branches is lucrative for the country to reduce external input usage in organic horticultural production.

This work discusses laboratory measurements of atomic and diatomic molecular species in laser-plasma generated in gases. Noticeable self-absorption of the Balmer series hydrogen alpha line occurs for electron densities of the order of one tenth of standard ambient temperature and pressure density. Emission spectra of selected diatomic molecules in air or specific gaseous mixtures at or near atmospheric pressure reveal minimal plasma re-absorption. Abel inversion of the plasma in selected gases and gas mixtures confirm expansion dynamics that unravel regions of atomic and molecular species of different electron temperature and density. Time resolved spectroscopy diagnoses self-absorption of hydrogen alpha and hydrogen beta lines in ultra-high pure hydrogen gas. Radiation from a Nd:YAG laser device induces micro-plasma for pulse widths in the range of 6 ns to 14 ns, energies in the range of 100 mJ to 800 mJ, and for peak irradiance of the order 1 to 10 TW/cm². Atomic line profiles yield electron density and temperature from fitting of line profiles to wavelength and sensitivity corrected spectral radiance data. Analysis of measured diatomic emission data yields excitation temperature of primarily molecular recombination spectra. Applications of the laboratory experiments extend to investigations of stellar astrophysics white dwarf spectra.

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

Zinc cobalt oxide-zinc hydroxide (ZnCo2O4-Zn(OH)2) microspheres were successfully fabricated on carbon cloth via a sample hydrothermal method. The surface morphology of these microspheres and their efficacy in degrading methyl violet were further modulated by varying the thermal annealing temperatures. The manipulation of thermal annealing temperatures was pivotal in adjusting the porosity of ZnCo2O4-Zn(OH)2 microspheres to amplify their photocatalytic performance. Various analytical techniques were utilized to evaluate the physical and chemical properties of the ZnCo2O4-Zn(OH)2 microspheres, including field-emission scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, field-emission transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis spectroscopy. Compared to untreated ZnCo2O4-Zn(OH)2 microspheres, those subjected to thermal annealing exhibited increased specific surface area and light absorption capacity, rendering them highly effective photocatalysts under UVC light exposure. Subsequent studies have confirmed the superior performance of ZnCo2O4-Zn(OH)2 microspheres as a reusable photocatalyst for degrading methyl violet and tetracycline. Additionally, trapping experiments during the photodegradation process involving ZnCo2O4-Zn(OH)2 microspheres have identified hydroxyl radicals (·OH) and superoxide radicals (·O2–) as the primary reactive species.

Ecological Society is based on socioeconomic systems directed to the equilibrium of inter-relationships between environment, climate, production systems, technologies and human communities to promote the overall well-being of people and the Earth planet. It has a main goal for supporting sustainable development and equitable societies and achieving optimal health outcomes recognizing the interconnection between people, technologies, animals, plants, and their shared environment for the one health. Using data of scientific publications and patents until the year 2024, this study shows new technologies that can support the energy transition with the shift from fossil fuels to renewable energy sources in an effort to reduce CO₂ emissions for an ecological society having, whenever possible, zero-carbon economies to reduce environmental pollution and climate change and foster health and wellbeing of people. Results reveal that sustainable technologies supporting the transformation of the energy sector, economies and societies, and having a rapid growth, are blue hydrogen, floating photovoltaic systems, carbon capture and utilization, green hydrogen and liquid metal batteries. These findings can guide decisions of policymakers and stakeholders towards fruitful investments driving the transition from fossil-based to zero-carbon socioeconomic systems to have a long-run sustainable development of overall world system that has to direct towards an ecological society associated with one health.

This case study focuses on exploring the potential of biogas as a direct substitute for conventional fossil fuels in industrial applications. Instead of being limited to its common uses as a vehicle fuel or for power generation, this research aims to investigate how biogas can be integrated into industrial processes as an advanced and sustainable energy solution. By conducting a detailed analysis of the financial implications associated with the utilization of landfill gas and gas derived from biomass, a comprehensive understanding of their practical applications in the industrial sector can be obtained. This research goes beyond a superficial examination and delves into the intricate aspects of incorporating biogas as a viable alternative fuel source. When we say that utilizing biogas is technically feasible, it means that the necessary infrastructure and technologies are available to support its integration into industrial processes. This implies that there are existing methods and systems in place that can efficiently harness and utilize biogas for various industrial applications. These technologies ensure a seamless transition from conventional fossil fuels to renewable energy sources, leading to a more sustainable and environmentally friendly industrial landscape. Moreover, the statement that utilizing biogas is economically feasible emphasizes that the financial viability of employing biogas in industrial processes is advantageous. This research explores the potential cost savings and benefits associated with substituting conventional fuels with biogas. By carefully examining the economic aspects, such as initial investments, operational costs, and potential revenue streams, a comprehensive understanding of the financial impact of adopting biogas solutions in the industrial sector can be gained. By expanding and broadening the understanding of the technical and economic feasibility of biogas integration, this research aims to provide valuable insights into the potential of advanced biogas solutions for industrial applications. Indeed, to make biogas a viable and sustainable option as a raw material, it is necessary to establish farming subsidies and financial support specifically tailored for biogas production, similar to the existing support provided for food production. These subsidies and financial incentives play a crucial role in promoting and encouraging the growth of the biogas industry. By establishing such support systems, farmers and other stakeholders in the agricultural sector can be incentivized to participate in the production of biogas. This can involve the utilization of agricultural waste, organic residues, or dedicated energy crops for biogas generation. The financial assistance can help offset the initial investment costs, provide incentives for production, and ensure the economic viability of biogas projects. Moreover, when considering large-scale landfills or situations where industrial demands for energy are relatively low, landfill gas becomes a viable and practical option. Landfill gas, which is generated by the decomposition of organic waste in landfills, can be harnessed and utilized for various industrial purposes. This not only helps in managing waste but also provides a valuable source of renewable energy. In summary, while farming subsidies and financial support are crucial for promoting biogas production, landfill gas remains a viable option for large landfills or situations with minor industrial demands. The combination of these two approaches offers a comprehensive outlook on utilizing biogas as a renewable energy source for industrial applications.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

It is known that the elastic characteristics of polyamides change with increasing temperature, in particular, the Young's modulus decreases significantly. This fact is practically not taken into account in design calculations of metal-polymer plain (MP) bearings, operating under conditions of the boundary and dry friction. The purpose of the study is the analysis of the effect of temperature on the change of the Young's modulus and, accordingly, the contact strength and triboresource according to the developed method of calculating MP bearings. MP bearings with a bushing made of polyamide PA6 reinforced with glass or carbon dispersed fibers were investi-gated. Quantitative and qualitative regularities of change of the maximum contact pressures and resource of the bearings at temperature increase under conditions of boundary and dry friction are established. The pressures in the bearing bushing made of PA6+30GF will be lower than for the bushing made of PA6+30CF. The resource of the bushing made of PA6+30CF will be significantly greater than for PA6+30GF. For thermoplastic polymers, the increase in temperature will have a useful practical effect due to the decrease in the rigidity of the polymer composites of the bearing bushing.

In this paper, based on the symmetrical reliability theory, a research method for the safety factor of overall overturning stability of continuous beam bridge under carbon fiber reinforced polymers (CFRP) during cantilever and horizontal rotation construction is proposed. Under the premise that the given target reliability index is known, the method solves the overall overturning stability safety factor of continuous beam bridge under carbon fiber reinforced polymers during cantilever and horizontal rotation construction by using the symmetrical reliability analysis theory and considering the randomness of structural parameters. This method is used to calculate the safety factor and the design reinforcement aera of CRFP of overturning stability and the design reinforcement aera of CRFP of a continuous beam bridge, and the parameters are analyzed. The calculation results show that the randomness of parameters will have a great impact on the overall safety factor and the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge, and ignoring the influence of randomness of parameters will lead to overestimation of the overall safety factor and underestimation of the CRFP aera of overturning stability of cantilever and horizontal rotation construction of continuous beam bridge.

The reliable online analysis of volatile compounds in exhaled breath remains a challenge as a plethora of molecules occur in different concentration ranges (i.e. ppt to %), and need to be detected against an extremely complex background matrix. While this complexity is commonly addressed by hyphenating a specific analytical technique with appropriate preconcentration and/or preseparation strategies prior to detection, we herein propose the combination of three analytical tools based on truly orthogonal measurement principles as an alternative solution: field-asymmetric ion mobility spectrometry (FAIMS), Fourier-transform infrared (FTIR) spectroscopy-based sensors utilizing substrate-integrated hollow waveguides (iHWG), and luminescence sensing (LS). These three tools have been integrated into a single compact analytical platform suitable for online exhaled breath analysis. The analytical performance of this prototype system was tested via artificial breath samples containing nitrogen (N2), oxygen (O2), carbon dioxide (CO2) and acetone as a model volatile organic compound (VOC) commonly present and detected in breath. Functionality of the combined system was demonstrated by detecting these analytes in their respectively breath-relevant concentration range and mutually independent of each other generating orthogonal yet correlated analytical signals. Finally, adaptation of the system towards the analysis of real breath samples during future studies is discussed.

The UK economy is overly reliant on unsustainable production and consumption practices, depleting finite resources at rates that will increase production costs, business risk and economic instability. This over-consumption produces emissions and waste that cause climate change and environmental degradation, impacting on the wellbeing of people in the UK and beyond. The Resource Recovery from Waste programme (RRfW) promotes a transition towards waste and resource management in a circular economy that restores the environment, creates societal benefits and promotes clean growth by engaging relevant actors in the transition process. RRfW collaborates with academia, government, and industry to co-produce a shared vision and approach to realise such a transition. Reflecting insights from RRfW’s government engagement, this article presents a positive outlook for changing the UK economy and society. It envisions a long-term future for waste and resource management that maximises the value of materials by circulating them in the economy for as long as possible. Four themes and an approach are proposed, including recommendations for regulatory instruments and a stable policy framework. It recommends further collaborative research to capitalise on opportunities for economic growth, innovation and resilient infrastructure whilst contributing to quality jobs and welfare in all four UK nations.

Leguminous Inga trees are thought to enhance soil carbon (C) accumulation following reforestation through mostly unknown mechanisms. This study amplified soil DNA using the ITS1F and ITS4 primers for PCR and Illumina MiSeq methods to identify fungal taxa, and traditional C analysis methods to evaluate how planted 4, 8, 11-year-old, Inga punctata trees affected soil fungal community compositions and C utilization patterns compared to old growth I. punctata trees and adjacent unplanted pasture within the same reforestation zone in Monteverde, Costa Rica. Along the tree age gradient the planted I. punctata trees enhanced the tree soil C-capture capacity as indicated by increased levels of soil Biomass-C, Respiration, and efficiency of organic C use (as lower qCO2 values), and development of increasingly more abundant, stable and successionally developed fungal communities, including those associated with decomposition of complex organic C compounds. The level and strength of differences coincided with differences in time of separation between the pasture and tree age or between the different tree ages. Fungal taxa were also identified as potential indicators of early and late stages of soil recovery. Thus, planting I. punctata should be part of future reforestation strategies used in this region of Costa Rica.

Artificial Intelligence (AI) is poised to revolutionize the architectural design and energy management of green buildings, offering significant advancements in sustainability and efficiency. This paper explores the transformative impact of AI on improving energy efficiency and reducing carbon emissions in commercial buildings. By leveraging AI algorithms, architects can optimize building performance through advanced environmental analysis, automation of repetitive tasks, and real-time data-driven decision-making. AI facilitates precise energy consumption forecasting and integration of renewable energy sources, enhancing the overall sustainability of buildings. Our study demonstrates that AI can reduce energy consumption and CO2 emissions by approximately 8% and 19%, respectively, in typical mid-size office buildings by 2050 compared to conventional methods. Further, the combination of AI with energy efficiency policies and low-emission energy production is projected to yield reductions of up to 40% in energy consumption and 90% in CO2 emissions. This paper provides a systematic approach for quantifying AI's benefits across various building types and climate zones, offering valuable insights for decision-makers in the construction industry.

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

The increasing social pressure for decarbonization has placed businesses under considerable scrutiny to actively reduce carbon emissions. A critical step towards achieving this objective is to shift conventional production and consumption systems to more sustainable alternatives. Thus, there is the emergent need to understand the patterns and drivers of the transformative business models (BMs) that underpin that shift. This study adopts a mixed-methods approach that integrates different literature streams--including Sustainability Transitions Theory (STT), Strategic Niche Management (SNM), and the Business Models approach--and stakeholders’ interviews to investigate the key elements of business models that lead towards sustainable practices. This research examines the organizational arrangements of European start-ups operating between 2014 and 2020. The transformation towards decarbonized production and consumption is characterized by efficient combination of business strategies that incorporate advanced technologies (ATs), such as artificial intelligence (AI), machine learning (ML) and its algorithms, along with sustainable elements, resulting in transformative business models. By exploring the driving elements behind the transition to low-carbon approaches, this study fills a significant gap in the existing literature on business models. The findings from this research also hold relevance for policymakers to promote decarbonization.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

Carbon dioxide capture and storage (CCS) is a necessary requirement for high-emitting CO2 industries to significantly reduce volumes of greenhouse gases released to the atmosphere and mitigate the climate change. Geological CO2 storage into depleted oil and gas fields is the fastest and most accessible option for CCS deployment allowing for re-purposing of existing infrastructure and utilizing the significant knowledge about the subsurface acquired during the field production operations. Location of such depleted fields in neighbourhood of high-emitting CO2 industries is additional advantage available for matured on-shore Europe fields. Considering these advantages, the oil and gas operators are now evaluating different possibilities for CO2 sequestration projects for the fields approaching end of production. This article describes an integrated approach to reservoir simulations focused on evaluating CO2 injection pilot at one of such matured fields operated by MND and located in the Czech Republic. The potential CO2 injection site in focus is a naturally fractured carbonate reservoir. This oil-bearing formation has a gas cap at the top and a limited aquifer at the bottom of the reservoir and was produced mainly by pressure depletion with quite limited pressure support from water injection. The article summarizes results of efforts taken by the multi-disciplinary team to develop and apply an integrated approach to reservoir simulation started from geological modelling of the naturally fractured reservoir and integrating results of laboratory studies and their interpretation (geomechanical and geochemistry laboratory experiments) and dynamic field data analysis (pressure transient analysis including time-lapse) into the history matching of the reservoir model and simulations of pilot CO2 injection. Attention is given to evaluating and modelling stress-sensitive fracture properties and safe injection envelope preventing induced fracturing as well as impact of potential salt precipitation in the near wellbore area. These effects are considered in the context of pilot CO2 injection and addressed in reservoir simulations of the injection scenarios. Single porosity and permeability reservoir simulations with dominating fracture flow and black-oil formulation with CO2 simulated as a solvent were used in this study and arguments for such choice of the simulation approach for the site in focus are shortly discussed. The reservoir simulations have indicated larger site injection capacity than required for the pilot injection and allowed to evaluate CO2 migration pathway within the reservoir. The application of the approach to the site in focus has also revealed large uncertainties, related to fracture description and geomechanical evaluations, resulted in an uncertain safe injection envelope. These uncertainties should be addressed in further studies in preparation to the pilot. The article concludes with an overview of the outcomes of the integrated approach and its application to the field in focus including discussion of issues and uncertainties revealed.

This study addresses the pressing energy constraints in nations like Bangladesh by proposing the implementation of photovoltaic (PV) microgrids. Given concerns about environmental degrada-tion, limited fossil fuel reserves, and volatile product costs, renewable energy sources are gaining momentum globally. Our research focuses on a grid-connected solar PV system model at Char Jazira, Lalpur, Natore, Rajshahi, Bangladesh. Through PVsyst simulation software, we assess the performance ratio (PR) and system losses, revealing an annual solar energy potential of 3375 MWh at Standard Test Condition (STC) efficiency. After considering losses, the system generates 2815 MWh annually, with 2774 MWh exported to the grid. We analyze an average PR of 78.63% and calculate a levelized cost of energy (LCOE) of 2.82 BDT/kWh [1 USD = 110 BDT]. The financial assessment indicates a cost-effective LCOE for the grid-connected PV system, with an annual gross income of 27744 BDT from selling energy to the grid and operating costs of 64060.60 BDT/year. Remarkably, this initiative can prevent 33074.061 tCO2 emissions over the project’s 25-year lifespan.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

The increasing global demand for efficient and sustainable energy storage solutions has driven the exploration of sulfur-based battery technologies. Sulfur’s abundance, low cost, and high theoretical energy density make it a promising candidate for next-generation energy storage, particularly in electric vehicles (EVs) and renewable energy systems. This paper reviews the development of sulfur-based batteries, including lithium-sulfur (Li-S), sodium-sulfur (Na-S), magnesium-sulfur (Mg-S), solid-state sulfur, sulfur-carbon nanocomposites, and hybrid sulfur flow batteries. Each technology is analyzed based on its advantages, challenges, and potential applications. Key research areas such as advanced electrolytes, nanomaterial integration, and sustainable manufacturing are highlighted, along with the current technological barriers to large-scale adoption. This review underscores the importance of continued research and innovation in sulfur-based battery technology to meet future energy storage demands.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

first_pagesettingsOrder Article ReprintsOpen AccessArticleThe Carbon Footprint of Spanish University Websitesby Sonia Sanchez-Cuadrado ¹ andJorge Morato ^2,*1Department of Library and Information Science, Complutense University of Madrid, 28010 Madrid, Spain²Department of Computer Science, Carlos III University of Madrid, Leganes, 28911 Madrid, Spain^*Author to whom correspondence should be addressed.Sustainability 2024, 16(13), 5670; https://doi.org/10.3390/su16135670 (registering DOI)Submission received: 31 May 2024 / Revised: 22 June 2024 / Accepted: 23 June 2024 / Published: 3 July 2024(This article belongs to the Special Issue Sustainable Education in the Digital Society: Applying Communication Technologies and Digital Tools to Education) Downloadkeyboard_arrow_down Browse Figures Versions NotesAbstractThe consumption of digital content is essential for economic and scientific development, leading to a high dependence on information and communication technologies, which significantly impacts the environment. Quantifying this ecological impact is challenging due to its intangible nature and the diversity of factors. This research focuses on assessing the energy consumption and CO₂ production of Spanish university websites to evaluate their levels of digital pollution and environmental impact. The calculation of the carbon footprint considers factors related to energy consumption and the use of green or renewable energies. The findings indicate that only 17% of university websites can be considered environmentally friendly. There are significant differences in CO₂ consumption and emissions depending on whether the websites implement environmentally sound practices. This study highlights the lack of initiatives aimed at reducing energy consumption and greenhouse gas emissions associated with web information management. The study shows that Spanish universities have the potential to contribute to the reduction in CO₂ emissions by implementing sustainable development practices on their websites. Furthermore, it fosters awareness about technology usage and its environmental impact, promoting the adoption of green and sustainable approaches.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

The objective of this study was to identify the factors determining a company’s corporate governance related to climate change. We analyzed the effect of various sustainability corporate governance variables on the disclosure level of climate change governance. These variables included facts such as having a dedicated sustainability executive and board committee, the mediating effect of female representation on the board of directors, number of reporting years according to TCFD, membership in a sustainability index, MSCI ESG rating, the existence of a corporate climate transition plan, a mention of the UN Global Compact and GRI, company location, as well as company size and profitability. By adopting a multi-theoretical framework that included stakeholder theory as well the legitimacy and agency theory, the underlying research study used a sample of 100 of the largest global companies by market capitalization and their reporting for the year 2020. Based on 1,400 observations for fiscal year 2020 and using correlation analysis, univariate and linear multiple regressions, we find a positive association between having a climate transition plan in place, being a leader in sustainability according to MSCI ratings, and being a DJSI constituent and the propensity to disclose information on governance for climate change. In addition, we find a company with a dedicated sustainability executive show an increased tendency to be transparent on climate governance issues. Furthermore, having a company location in a developed country is significantly and positively associated with climate change governance. Surprisingly, gender diversity in the corporate board or having a sustainability board committee did not show any significant correlation between a higher climate change governance level. The same was true for companies being active in either the extractive or non-extractive sector. Companies referring to the Global Reporting Initiative (GRI) or UN Global Compact also did not score higher in climate change governance. Neither did corporate profitability or size play a significant role. Our results are robust to variations and provide valuable insights for researchers, academics, executives, practitioners as well as regulators. As more and more companies are shifting towards a climate change reporting framework, it is of paramount importance that we are able to determine the contributing variables that lead to effective climate change corporate governance. Our results are inconsistent with stakeholder theory and are strongly suggesting that a diversified board and the existence of a sustainability committee that meets often/sufficiently may not necessarily lead to a higher level of transparency/quality regarding climate change. While more research is needed, knowing that a dedicated sustainability executive as well as having a climate plan in place can make a difference in climate change reporting, can be very beneficial to many corporate stakeholders. Given the current urgent climate change situation and the crucial role that corporation play in it, dedicated sustainability positions and committees need to be established. The findings could be useful for managers as well as governmental standards setter and regulators who are interested in improving corporate practices dealing with climate change. This study applies STATA software with various regression models to empirically test the relationship between CG and other variables and corporate climate change reporting.