Timely processing of observations from hyper-spectral imagers, such as SEVIRI (Spinning Enhanced Visible and Infrared Imager), largely depends on fast radiative transfer calculations. This paper mostly concerns the development and implementation of a new forward model for SEVIRI to be applied to real time processing of infrared radiances for the physical retrieval of surface temperature and emissivity. The new radiative transfer model improves computational time by a factor of ≈ 7 compared to the previous versions and makes it possible to process SEVIRI data at nearly real time. The new forward model has been applied for the simultaneous retrieval of surface temperature and emissivity in three infrared channels (8.7, 10.8, 12 μm). The inverse scheme relies on a Kalman filter approach, which allows us to exploit a sequential processing of SEVIRI observations. Based on the new forward model, the paper also presents a validation retrieval performed with in situ observations acquired during a field experiment carried out in 2017 at Gobabeb (Namib desert) validation station. Furthermore, a comparison with IASI (Infrared Atmospheric Sounder Interferometer) emissivity retrievals has been performed as well. It has been found that the retrieved emissivities are in good agreement with each other and with in situ observations, i.e. average differences are generally well below 0.01.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

Purpose: To investigate the extent of anterior chamber angle circumference needed to maintain a physiological outflow facility (C). Methods: Twenty anterior segments of porcine eyes were assigned to 5 groups, each with a different degree of cyanoacrylate-mediated angle closure: 90° (n = 4), 180° (n = 4), 270° (n = 4), 360° (n = 4) and four unoccluded control eyes. The outflow facility was measured at baseline, 3, 12, 24, and 36 hours after angle closure. Outflow patterns were evaluated with canalograms and the histomorphology was compared. Results: Baseline outflow facilities of the five groups were similar (F = 0.922, P = 0.477). Complete, circumferential occlusion over 360° induced a significant decrease in facility from baseline at all time-points (P ≤ 0.023 at 3, 12, 24 and 36 hours). However, no difference from baseline was found in any of the partially-occluded (0–270°) groups (F ≥ 0.067, P ≥ 0.296 at 3, 12, 24 and 36 hours). The canalograms confirmed the extent of occlusion with flow through the unblocked regions. Histology revealed no adverse effects of blockage on the TM or aqueous plexus in the unoccluded angle portions. The unoccluded TM appeared normal. Conclusion: Cyanoacrylate-mediated angle occlusion created a reproducible angle closure model. 90° of unoccluded anterior chamber angle circumference was sufficient to maintain physiological outflow. This model may help understand how outflow can be regulated in healthy, nonglaucomatous TM.

Objective: This paper aims to build an Effort Estimation Model for design, coding and testing Web Applications Based Fuzzy and Practical Models, which will help in optimizing the efforts in software development. Methods/Analysis: Soft computing approach is adopted and applied in the effort estimation and then compared with practical efforts in the development process with interpreting the historical data available for the existing functionalities. Findings: The effort estimation model presented in this paper focuses on the first level estimates published by Project Managers and the second level estimates presented by Project Leaders or Developers for any new requirement or enhancement for a web application built on 3-tier architecture using Microsoft technologies. The model considers the classification of each task as either Low or Medium or High complexity. These tasks pertain to the lowest level parts in bottom-up estimation. Efforts are estimated for designing, coding and unit testing of these tasks and the efforts are summed up to get the effort estimation for the higher level which is a feature to be implemented. Novelty/Improvement: The paper also discusses about the application of the effort estimation model by taking a new requirement as a case study. The first level estimates calculated using the effort estimation model has a variance of about 25% when compared with the actual effort. This variance is very much acceptable considering the fact that the first level estimates can be tolerable up to 35%. The proposed effort estimation tool would help the project managers to efficiently control the project, manage the resources effectively, and improve the software development process and also trade off analyses among schedule, performance, quality and functionality. Fuzzy logic is used to verify the claims made in efforts estimation. It is proposed a new relation between the number of data and efforts value membership for actual data. And converts it into crisp value in the range [0…1] which helps to classify the complexity of the task and subtask in the design, coding and testing phases.

Some of the recent large-scale national projects in South Korea are delayed or suspended due to belated responses to risk occurring on site. Currently, the Far East District (FED) project is being implemented to relocate the US Army bases from Yongsan to Pyeongtaek. Because of lack of experience and understanding about the characteristics of such a project, the deadline of taking over to the US Army Korea has been missed. This study identifies problems of each participant in the Yongsan Relocation Plan (YRP) of the US Army Korea with respect to construction project management and establishes a risk management strategy reflecting characteristics of FED project. To derive significant risk factors influencing YRP, various field data like weekly and monthly reports and other reports on construction condition are analyzed, and experts’ advices are collected and a survey is conducted. Mediators and latent variables are ultimately obtained. Furthermore, a structural equation model is used to both analyze and evaluate complex causal relations among many variables of YRP. The impact of risk factors on the schedule, quality and cost of the project is analyzed. In particular, the case of Site A is examined to see how the project is affected by those risk factors.

The creation of computer models is often driven by the need to make predictions in regions where there is no data (i.e. extrapolations). This makes validation challenging as it is difficult to ensure that a model will be suitable when it is applied in a region where there are no observations of the system of interest. The current paper proposes a method that can reveal flaws in a model which may be difficult to identify using traditional approaches for model calibration and validation. The method specifically targets the situation where one is attempting to model a dynamical system that is believed to possess time-invariant calibration parameters. The proposed approach allows these parameters to vary with time, even though it is believed that they are time-invariant. The of such an analysis is to identify key discrepancies - indications that a model has inherent flaws and, as a result, should not be used to influence decisions in regions where there is no data. The proposed method isn't necessarily a predictor of extrapolation performance, rather, it is a stringent test that, the authors believe, should be applied before extrapolation is attempted. The approach could therefore form a useful part of wider validation frameworks in the future.

Fusarium graminearum causes head blight in wheat and corn, and produces chemicals harmful for humans and other animals. It is important to understand how it grows in order to prevent outbreaks. There are 3 well-known growth models for microorganisms and they seem applicable to molds: linear, Gompertz and Baranyi. This study aimed to see which could better represent F. graminearum growth. Three replicates were grown in yeast extract agar (YEA) for 20 days. The Feret’s radius was measured in ImageJ software, and then related to the models. Linear model was the most closely correlated to the actual growth. Thus, considering that it was the most representative of the reality and it is easier to use, it seems to be the best logical choice for F. graminearum growth studies.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

As climate is not only a valuable tourism resource but also a factor influencing travel experience, estimating climate change can provide implications to sustainable development of the tourism industry. This study develops Climate Volatility Index (CVI) using GARCH model and estimates the relationship between CVI and Japanese tourism demand for Korea using a tourism demand model, based on data from January 2000 to December 2013. Time lag is applied based on a decision making process regarding travel destinations. The result shows that an increase in volatility of climate change leads to a decrease in tourism demand.

Abstract: Background and objective: Propofol is an anesthetic agent that is frequently used in anesthesia induction, maintenance and sedation. Propofol has severe side effects such as hypotension, bradycardia and respiratory depression. Although propofol is commonly used, there is no known antidote for its toxic effects. An approach to prevent toxic effects of propofol would be beneficial. The aim of this study was to assess the effects of intravenous lipid emulsion (ILE) therapy in the prevention of depressive effects of propofol on cardiovascular and respiratory systems. Materials and methods: Twenty-eight Sprague-Dawley adult rats were randomly divided into 4 groups. The saline-administered group was determined as the Control group. The second group was administered propofol (PP group); the third group was administered ILE (ILE group), and the fourth was administered propofol with ILE therapy (ILE+PP group). Systolic blood pressure (SBP), Diastolic blood pressure (DBP), Mean arterial blood pressure (MAP), Respiratory rate (RR), Heart rate (HR) and mortality were recorded at 10 points during 60 minutes. A repeated measures linear mixed-effect model with unstructured covariance was used to compare the groups. Results: In the PP group, SBP, DBP, MAP, RR and HR levels were declining steadily; all rats in this group died after 60 minutes. In the ILE+PP group, after a while, the decreased SBP, DBP, MAP, RR and HR levels increased SBP, DBP, MAP, RR and HR levels of the Propofol group were found to be significantly lower than those of the other groups (p<0.01). The mortality rate was 100% (surviving period, 60 min) for the PP group, whereas 0% for the ILE, ILE+PP and Control groups. Conclusion: Our results suggest that undesirable side effects that can be seen after propofol application such as hypotension, bradycardia and respiratory depression might be prevented by using ILE therapy.

A diagnostic method is presented for analysing the large-scale behaviour of the Met Office Unified Model, which is a comprehensive atmospheric model used for weather and climate prediction. Outside the boundary layer, on scales larger than the radius of deformation, semigeostrophic theory will give an accurate approximation to the model evolution. In particular, the ageostrophic circulation required to maintain geostrophic and hydrostatic balance against prescribed forcing and a rate of change of the geostrophic pressure can be calculated. In the tropics the balance condition degenerates to the weak temperature gradient approximation. Within the boundary layer the semigeostriptic approximation has to be used because friction and rotation are equally important. Assuming the calculated pressure tendency and ageotriptic circulation match the observed model behaviour, the influence of the large-scale state and the nature of the forcing on the model response can be deduced in a straightforward way. This process is illustrated by comparing predictions of the ageotriptic circulation from the theory and the model. It is then used to show that the effects of latent heat release can be included by modifying the static stability, and to show the effect of an idealised tropical heat source on the subtropical jet. Finally the response of the ageotriptic flow to boundary layer heating in the tropics is demonstrated. These illustrations show that the model behaviour on large scales conforms with theoretical expectations, so that the results of the diagnostic can be used to aid the development of further improvements to the model.

PEM fuel cell is a technology successfully used in the production of energy from hydrogen, allowing the use of hydrogen as an energy vector. It is scalable for stationary and mobile applications. However, the technology demands more research. An important research topic is fault diagnosis and condition monitoring to improve the life and the efficiency and to reduce the operation costs of PEMFC devices. Consequently, there is a need of physical models that let deep analysis. These models must be accurate enough to represent the PEMFC behavior and to allow the identification of different internal signals of a PEM fuel cell. This work presents a PEM fuel cell model that uses the output temperature in a closed loop, so it can represent the thermal and the electrical behavior. The model is used to represent a NEXA Ballard 1.2 kW; therefore it is necessary to fit the coefficients to represent the real behavior. Five optimization algorithms were tested to fit the model, three of them were taken from literature and two were proposed. Finally, the model with the parameters identified was validated with real.

The non-existence of a land ownership database in most of the developing countries moves the inhabitants to the occupation of public lands. Some of this situation are the origin to areas of informal housing, commerce and agriculture and in the end into new ​​informal settlements. Informal settlements become a serious problem in developing countries. The most common typology of informal settlements is that they are the population settled in public lands without any infrastructures and against the administrator's will. Thought this action the result in an uncontrolled land occupation process that promotes new informal areas without any proper built-up utilities, located in risk areas on the territory, barely ensuring the minimum requirements for a heaty living of the population and in various cases incentives to an informal economy. The process of build a cadastral map in informal settlement areas is a fundamental base to support the future transformation of illegal areas and to regulate the occupation of new subdivision planning and into the creation of new expansion areas. In this paper, it is presented a methodology developed to be applied to support a new register of land and to management. The transformation of informal settlement areas. The model to register the land tenure has been associated with allows the process application to multiple typology of informal settlements. The model to register land tenure has developed on a series of qualitative and quantitative data that determine the identification and classification of the buildings and its physical and functional description. The model was developed using Geographic Information System and with an initial survey of existing land titles of possession and public proposals to develop new expansion areas. A case study of the method is presented, where the land management model was implemented - Chã da Caldeiras in Ilha do Fogo an informal settlement in Cape Verde. The results are a great acceptance of the proposal by the population and local authorities and the starting of the implementation phase.

This research aimed to develop a causal relationship model of the behavior of a Thai rural community in disposing of used batteries. The variables studied were 1) the household latent variable (three observable variables); 2) the social latent variable (six observable variables); 3) the intention latent variable (three observable variable); and 4) the behavior latent variable (three observable variables). Six hundred households were surveyed using a questionnaire. The questionnaire developed was validated by seven experts and its reliability was established by testing it with a sample group. Results showed that the modified model do present a good overall level of fit. The House and social positively and directly influenced intention. Intention positively and directly influenced behavior. The theoretical and practical implications relating specifically to intention to the behavior in disposing of used dry batteries by households are emphasized. The modified model indicated eighty-nine percent of the variance in the behavior in disposing of used dry batteries by households was explained by the intention factors. The most direct effect on behavior was the intention factors with 0.89 of effect size. The factors with indirect effects on behavior were household and social factors with an effect size of 0.52 and 0.35.

The study aims to analyze the performance criteria of the GR4J model to reproduce high water flows in the Ouémé watershed at Bonou's outlet which has been vulnerable to climate change in recent decades. The methodology focused on the use of daily climatological and hydrometric data extracted from files of National Directorate of Meteorology, and General Directorate of Water; they were supplemented by those of SIEREM/HSM dataset over the period 1961-2015. The rainfall was regionalized using Thiessen method. The performance of the GR4J model was assessed with NSE, RMSE and KGE criteria. The results indicate that the study area is marked by rainfall variabilities and detection of two breakpoints (1968 and 1987) which divide the series into three sub-periods; these discontinuities have repercussions on the streamflow. It's found that GR4J model overestimates the streamflow during the low water period and underestimates them in high water. However, the efficiency and performance criteria NSE, RMSE and KGE calculated on high water flow rates are better in calibration than in validation. The KGE values are range between 83-85% in calibration and 56-68% during validation, which gives to GR4J model the efficiency and performance to reproduce high flow rates in the study area

SLEUTH Model (slope, landuse, exclusion, urban extent, transportation and hillshade) is an important tool for landuse planning and land policy. To evaluate the performance of SLEUTH model, implementation of Sensitivity Analysis (SA) is essential. The main limitation of SA in SLEUTH application is a lack of insight into model input self-modification parameters (SMPs) variation, namely, uncertainty involved in the model transfer metrics and model presumptions, which often misled the decision makers and model users. To address this issue, this study divided the forward process into two stages. Firstly, during the transfer process ①, the contribution scores of five SMPs were drawn, and parameters highly sensitive to model output were given. Apart from that, the recommended initial value for SMPs of 0.11, 0.2, 0.87, 1.13, 15, 1.01, 0.49 were found to be subordinated to such a heterogeneous urban area simulation. Secondly, during the transfer process ②, SMP caused imagery metrics indicated the disparity between parameters with Fixed Reference and with Successive Reference. Reversely, it derives reasonable threshold for the best fit values of five prediction coefficients’ initialization by comparing the real image with the predicted one. The framework of SLEUTH model transfer mechanism not only could distinguish highly sensitive SMPs with higher contribution scores, but also could give parametric analysis for simulation imagery based on metrics. The study was found to be a practical tool for quantization response of model input variables for modelling complex urban systems. So, this insight can help geographic information scientists decide how to find out the inner forward transfer mechanism of SLEUTH model for further make good use of it and improve the model.

Migrations are much more important than currently recognised, for explaining important patterns observed in the European archaeology record – according to this archaeology led model. At a high level, they explain the introduction of different farming, monument building, the spread of metalworking and patterns of trade and exchange. This paper presents an archaeogenetic model based on a strategic review of the Neolithic and Chalcolithic archaeology of Europe, alongside a review of recently published ancient DNA data. The model is archaeology led. It takes archaeology themes and proposes migratory events to explain them. Ancient DNA data and further archaeology evidence is then used to test these proposed migrations- to reject or refine them. The model introduces a new and more strategic way of looking at archaeological cultures - that updates early 20th century approaches to studying archaeology cultures, and integrates with the detailed ‘post processual’ studies of the late 20th Century. The model consists of seven maps – each showing multiple migration events – with key evidence to support each migration map. It proposes a new category of a ‘Black Sea’ related population that makes a major genetic contribution to the Middle Neolithic of Europe. The proposed migrations provide an explanation for the observed patterns of archaeology, for example: • multiple Neolithic migrations that introduced, farming and metalworking into Europe; • a major ‘Black Sea’ related ‘Middle Neolithic’ migration that carried advanced knowledge of astronomy that can be recognised in a variety of types of monument from the Neolithic through to Bronze Age Europe; and, • migrations of related cultures (‘supercultures’) that explain patterns of trade and exchange in Bronze Age western Europe. The model also provides ancient DNA and archaeology based support for the key aspects of Childe’s ‘dawn of civilisation’ in Europe and Egypt and Gimbutas’ ‘Old Europe’ and “three waves of migration from the Steppe”.

This paper proposes a novel model for a PV cell with parameters variance dependency on temperature and irradiance included. The model relies on commercial available data, calculates the cell parameters for standard conditions and then extrapolates them for the whole operating range. An up-to-date review of the PV modeling is also included with series and parallel parasitic resistance values and dependencies discussed. The parameters variance is analyzed and included in the proposed PV model, where the self-heating phenomenon is also considered. Each parameter variance is compared to the results from different authors. The model includes only standard components and can be run on any SPICE-based simulator. Unlike other approaches that consider the internal temperature as a parameter, our proposal relies on air temperature as an input and computes the actual internal temperature accordingly. Finally, the model is validated via experiments and comparisons to similar approaches are provided.

As a high fatal disease, fat embolism syndrome is complication, which brought great pain to patient and their family served as a serious social burden. The mechanism of FES remains unclear. Autophagy controls the cell survival and homeostasis by removing the mis-folded proteins and damaged organelles as well as intracellular pathogens through a lysosomal degradation pathway. Increasing research documented that autophagy was wildly involved in variety of human diseases and had huge therapeutic potential. In our study, we first established the rat model of FES with the liquid fat by tail vein injection. We observed the up-regulated MPO expression and activity, increased Wet-to-Dry (W/D) lung weight, promoted quantity of fat granules, and the dominant disorder in the lung rat model of FES, compared to the control group. These observations demonstrated that we successfully build the rat model of FES. Then, we sought to dissect the role of the autophagy in the rat model of FES. The western blots analysis showed that the autophagy was inhibited in the rat model of FES constructed with liquid fat. Furthermore, Rapamycin could restore the repression of autophagy in rat model of FES. These investigations illustrated that autophagy was involved in FES. In addition, our experiments showed that Rapamycin could alleviate the symptoms of FES. Taken together, our study demonstrated the participation of autophagy in FES and further, as a potential therapeutic target, the modulation of autophagy could affect the symptom of rat model of FES.

Hydro-climatic projections in West Africa are attributed with high uncertainties that are difficult to quantify. This study assesses the influence of the parameter sensitivities and uncertainties of three rainfall runoff models on simulated discharge in current and future times using meteorological data from 8 Global Climate Models. The IHACRES Catchment Moisture Deficit (IHACRES-CMD) model, the GR4J and the Sacramento model were chosen for this study. During model evaluation, 10,000 parameter sets have been generated for each model and used in a sensitivity and uncertainty analysis using the Generalized Likelihood Uncertainty Estimation (GLUE) method. Out of the three models, IHACRES-CMD recorded the highest Nash-Sutcliffe Efficiency (NSE) of 0.92 and 0.86 for the calibration (1997-2003) and the validation (2004-2010) period respectively. The Sacramento model was able to adequately predict low flow patterns on the catchment while the GR4J and IHACRES-CMD over and under estimate low flow respectively. The use of multiple hydrological models to reduce uncertainties caused by model approaches is recommended along with other methods of sustainable river basin managements.

The main contribution of this paper is to develop a graphical tool to evaluate the suitability of a candidate parametric model to fit a data set. The practical motivation is to check the adequacy of the so called SAINT model proposed in Jarner and Kryger (2011). This model has been implemented in practice by an important European pension fund concerned with setting annuity reserves for all current or former employees of Denmark. So, one particular relevant question is whether this mortality model is actually fitting old-age. Our graphical test can be described as follows. First we transform the data by means of the parametric model which is being evaluated. Should the model be correct, the transformed data will be in accordance with an Exponential distribution with rate 1. Then we construct a family of local linear hazard estimates based on the data on the transformed scale. Finally we use the statistical tool SiZer to assess the goodness-of-fit of the Exponential distribution to the data on the transformed scale. If the model is correct the SiZer map should not reveal any significant feature in the family of kernel estimates. Our method allow us to establish a diagnostic regarding the validity of the SAINT model when describing mortality patterns in four different countries.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The recent demand for reducing pollutant and CO2 emissions from internal combustion engines has created an urgent need for the development of ultra-lean burn engines that ensure combus-tion stability and reducing knocking tendency. One of the most promising methods is the Pre-chamber Spark Ignition (PCSI) system, where a jet of high-energy reactive gases, produced by pilot combustion in a pre-chamber, ignites the main combustion event in the cylinder. Given the intricate phenomena inherent to PCSI systems, conducting 3D CFD studies is imperative for a comprehensive analysis and optimal design. Furthermore, the detailed CFD model, combined with the calibrated 0-D/1-D model, is anticipated to yield a significant amount of new data that would be difficult to obtain through experimental approaches, making it essential for advancing our understanding and optimization of these systems. However, recently published papers re-port that some state-of-the-art models developed for conventional SI operation may not be pre-dictive under the challenging conditions of TJI systems, particularly under lean conditions. This review elucidates the reasons behind the widespread adoption of CFD in the optimal design of PCSI engines. It presents significant examples and delves into the potential and challenges of employing CFD not just as a predictive tool but also as a design instrument for enhancing PCSI engine performance.

Here we mathematically model black holes and the early universe following dynamics similar to RLC electrical models, focusing on their similarities at the singularity. We use this mathematically modelling to hypothesize the evolution of an expanding universe as the result of a black hole collapse followed by its evaporation. Or model consists of several steps defined by: (1) the formation of a black hole following general relativity equations; (2) growth of the black hole modelled as a resistance-capacitance-like electrical circuit; (3) expansion of space-time following the disintegration of the black hole, modelled by RLC-like dynamics. In updating this article, version 2, we will expand by presenting three additional examples related to the theory of the generalization Boltzmann's constant in curved space-time and the theory of general and especial relativity. We will calculate the critical mass to produce a black hole in the LHC, the existence of a high temperature Bose-Einstein condensate and finally we will demonstrate the existence of a tangential force to the repulsion force in the disintegration of subatomic particles. In the update of this article, version 3, we will expand to develop two examples. First, we will present the relationship between M-theory, extra dimensions with the theory of the generalization of Boltzmann's constant in curved space-time. Secondly, we will propose the idea of ​​updating the Lambda-CDM model, considering the primordial gravitational waves to correctly describe the evolution of the universe.

The use of logistic regression models in data analysis and machine learning has expanded in recent years and has become the primary preference of researchers in risk assessment studies across a wide range of scientific fields. From the assessment of credit risk in financial institutions to the estimation of risk factors for traffic accidents or the identification of etiological factors for chronic diseases. All logistic models are natural extensions of the simple binary model, and their interpretation is based on it. Using the data of a cross-sectional study on the risk factors of traffic collisions, the two main extended models of logistic techniques, multinomial and ordinal logistic regression, are presented in the article in detail. Emphasis is placed on the use of ordinal regression since the outcome variable of the collision data is defined as ordinal measurement reflecting a latent continuous scale.

The move to a low carbon economy is very important for enhancing international competitiveness. The eco-innovation is the critical factor of the green paradigm. This study is designed to investigate deeply the determinants of eco-innovation of manufacturing firms in Korea by suggesting anticipated regulations, self-regulations, and industry-specific characteristics as external factors and open information sources as internal factors. The data used in the analysis is 1946 sample firms from Korean Innovation Survey 2010 based on the Oslo Manual. Using the multi-variate probit analysis and the zero-inflated negative binomial (ZINB) regression analysis, we have found out that the anticipated regulations and self-regulations have significant influences both on eco-process innovation and eco-product innovation, while industrial characteristics have no effects. The empirical results also show that the breadth of information sources has a positive effect on businesses in implementing eco-innovations. Our findings show that the Korean government should provide a good platform where firms can better understand the future trends of environmental policies, particularly policies on anticipated and self-regulations. At the same time, Korean firms should establish a voluntary system to control environmental activities so that they can improve eco-innovations through integrating external information.

Into the frame of the French TANDEM project (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modelling) Principia has been working on the development and qualification of two in-house CFD software’s: the 2D EOLE-SV (Saint Venant) model for simulation of large scale tsunami propagation from the source up to coastal scale and the 3D EOLE-NS (Navier-Stokes) model dedicated to tsunami coastal impact modelling. This paper presents a large range of test cases carried out into the frame of the project and dedicated to the validation of numerical codes in various tsunami wave conditions. The main aspects of phenomena such as wave generation, propagation and coastal impact are investigated on academic situations. A real case simulation is concerned as well, the devastating 2011 Tohoku event which is compared with in-situ data.

Major marine construction projects, resulting in the release of sediments, are subject to environmental assessment and other regulatory approval processes. An important tool used for this is the development of specialized numerical methods for these marine activities. An integrated set of numerical methods addresses four distinct topics: the near-field release and mixing of suspended sediments into the water column (i.e. the initial dilution zone); the transport of the suspended sediments under the influence of complex ocean currents in the far-field; the settling of the transported suspended sediments onto the seabed; and the potential for resuspension of the deposited sediments due to sporadic occurrences of unusually large near-bottom currents. A review of projects subjected to environmental assessment in the coastal waters of British Columbia from the year 2006 to 2017, is presented to illustrate the numerical models being used and their ongoing development. Improvements include higher resolution model grids to better represent the near-field, the depiction of particle size dependent vertical settling rates and the computation of resuspension of initially deposited sediments, especially in relation to temporary subsea piles of sediments arising from trenching for marine pipelines. The ongoing challenges for this numerical modeling application area are also identified.

This paper presents a comprehensive investigation into the applicability and performance of two prominent growth models, namely the Verhulst model and the Montroll model, in the context of modeling tumor cell growth dynamics. Leveraging the power of Physics-Informed Neural Networks (PINNs), we aim to assess and compare the predictive capabilities of these models against experimental data obtained from the growth patterns of tumor cells. We employ a dataset comprising detailed measurements of tumor cell growth to train and evaluate the Verhulst and Montroll models. By integrating PINNs, we not only account for experimental noise but also embed physical insights into the learning process, enabling the models to capture the underlying mechanisms governing tumor cell growth. Our findings reveal the strengths and limitations of each growth model in accurately representing tumor cell proliferation dynamics. Furthermore, the study sheds light on the impact of incorporating physics-informed constraints on the model predictions. The insights gained from this comparative analysis contribute to advancing our understanding of growth models and their applications in predicting complex biological phenomena, particularly in the realm of tumor cell proliferation.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

Panoramic and periapical radiograph tools help dentists diagnose the most common dental diseases. Generally, dentists identify dental caries manually by inspecting X-ray images. However, due to their heavy workload, or poor image quality, dentists may sometimes overlook some unnoticeable dental caries, which may ultimately hinder the patient treatment. The purpose of this study was to develop an algorithm that classifies the teeth X-Ray images into three categories of “Normal”, “Caries”, and “Filled”. Our study used a dataset of 116 patients and 3712 single teeth images for training, validation and testing. Images were pre-processed using a sharpening filter and an intensity color map. We used a pre-trained transfer learning model, the NASNetMobile, which served as the feature extractor and the Convolutional Neural Network (CNN) model served as the classifier. The training dataset had a “Recall” of 0.92, 0.90 and 0.91 for “Normal”, “Caries” and “Filled” respectively and the test dataset had a “Recall” of 0.86, 0.81 and 0.85 for “Normal”, “Caries” and “Filled” respectively. The classification of the teeth X-Rays was successful and can be valuable for dentist as the artificial intelligence algorithm can serve as a decision support tool to aid dentists when they need to diagnose dental treatment.

The purposes of this study are based upon the theory of planned behavior (TPB) to examine the impact of past experiences of contract farming on selecting a specific type of contract farming in the future and then compare different psychological factors in the TPB for different potential contract farmer statuses. These statuses include homesteaders, farmers from cooperative farms, farmers from production and sales teams, professional farmers, and brokers. The impact of factors in the TPB for a particular contract type on potential contract farmers is further to compute. To this end, data are collected in three major sweet potato production areas in Taiwan. The results show that the farmers’ past contract farming experience does not influence the selection of the contract in the future. As for the selection of contract type, strengthening the perception and motivating the behavioral intention of contract farming for cooperative farms will increase the probability of selecting an unclassified sweet potato size contract. On the other hand, enhancing perceived behavioral control factors and behavioral intention factors for professional farmers and brokers is apt to have a relatively high probability of selecting those types involving the highest amount or the best price to obtain the best deal.

This paper aims to provide the smart grid research community with an open and accessible general mathematical framework to develop and implement optimal flexibility mechanisms in large-scale network applications. The motivation of this paper is twofold. On the one hand, flexibility mechanisms are currently a hot topic of research, which is aimed to mitigate variation and uncertainty of electricity demand and supply in decentralised grids with a high aggregated share of renewables. On the other hand, a large part of such related research is performed by heuristic methods, which are generally inefficient (such methods do not guarantee optimality) and difficult to extrapolate for different use cases. Alternatively, this paper presents an MPC-based (Model Predictive Control) framework explicitly including a generic flexibility mechanism which is easy to particularise to specific strategies such as Demand Response, Flexible Production and Energy Efficiency Services. The proposed framework is benchmarked with other non-optimal control configurations to better show the advantages it provides. The work of this paper is completed by the implementation of a generic use case which aims to further clarify the use of the framework and thus, to ease its adoption by other researchers in their specific flexibility mechanisms applications.

Financial Payment has evolved into mobile payment for easy access and convenience. Despite the benefits of mobile payment, the adoption rate is unsatisfactory worldwide. Therefore, understanding the customer's adoption intention factors is essential for both researchers and practitioners. This study examines mobile payment intention and actual use by adapting the integrated framework, which combines the Mobile Technology Acceptance Model and the Theory of Planned Behaviour with additional new constructs found to be related. The new model consists of 12 variables moderated by the individual's experience and is examined via a structured PLS equation mixed-mode methodology. Knowing mobile payment influence will shape the industry strategic decision and socially contribute to transforming society into a cashless society. This paper provides an opportunity to prove the relationship between technology variables and human behaviour concerning mobile payment adoption. In contrast, this study novelty adopted an integrated model that combines MTAM with the TPB.

In bioprocess engineering the Qualtiy by Design (QbD) initiative encourages the use of models to define design spaces. However, clear guides on how models for QbD are validated are still missing. In this review we provide a comprehensive overview about validation methods, mathematical approaches and metrics currently applied in bioprocess modeling. The methods cover analytics for data used for modeling, model training and selection, measures for predictiveness and model uncertainties. We point out general issues in model validation and calibration for different types of models and put this into context of existing health authority recommendations. This review provides the start-point for developing a guidance for model validation approaches. There is no one-fits-all approach but this review shall help to identify the best fitting validation method or combination of methods for the specific task and type of bioprocess models that is developed.

The new Post Accelerating Data and Knowledge Online Society, or ‘Padkos’ requires a new model of decision making. This introductory paper proposes a model where decision making and learning are a single symbiotic process, incorporating man and machine, as well as the AADD (ánthrōpos, apparatus, decider, doctrina) diamond model of individual and organizational decision-making and learning processes. The learning is incorporated by using a newly proposed quadruple loop learning model. This model allows for controlled changes of identity, the process of creating and the sense making of new mental models and assumption, and reflections. The model also incorporates the recently proposed model of quantum decision-making, where time collapse of the opted past and the anticipated future (explicitly including its time horizon) into the present play a key role in the process, leveraging decision-making and learning by human as well as Artificial Intelligence (AI) and Machine Learning (ML) algorithms. The paper closes with conclusions.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

The famous singlet correlations of a composite quantum system consisting of two spatially separated components exhibit notable features of two kinds. The first kind consists of striking certainty relations: perfect correlation and perfect anti-correlation in certain settings. The second kind consists of a number of symmetries, in particular, invariance under rotation, as well as invariance under exchange of components, parity, or chirality. In this note, I investigate the class of correlation functions that can be generated by classical composite physical systems when we restrict attention to systems which reproduce the certainty relations exactly, and for which the rotational invariance of the correlation function is the manifestation of rotational invariance of the underlying classical physics. I call such correlation functions classical EPR-B correlations. It turns out that the other three (binary) symmetries can then be obtained "for free": they are exhibited by the correlation function, and can be imposed on the underlying physics by adding an underlying randomisation level. We end up with a simple probabilistic description of all possible classical EPR-B correlations in terms of a "spinning coloured disk" model, and a research programme: describe these functions in a concise analytic way.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

This study aims at highlighting and illustrating innovative actions for achieving and/or improving accurate medical coding within a DRG system. Already grouped DRG cases recorded in the first DRG implementation year in the region of Crete were examined. A sample of 130,000, from a total of 200,000, cases were analyzed and audited, through a process consisting of three stages: i) Digitalization, ii) Auditor training, and iii) Control &amp; consultation. The results indicated that a significant proportion of DRG coding, with a length of stay exceeding one day, were reclassified into different DRG categories. This was not primarily due to errors in the selection of the principal diagnosis, but resulted from coding errors, including omission of secondary diagnoses coding, medical procedures that should have been included and utilization of less specific codes. The findings indicate that medical coding control, consulting services and the adoption of targeted actions can be instrumental for proper implementation of the DRG coding system, and for ensuring transparent allocation of resources within hospitals. Ultimately, this shortens the coding learning curve, from four years typically reported in the international literature, to a more efficient duration of two years, leading to rational and documented clinical and financial management of hospitals.

Nuʻupia Ponds, a traditional Hawaiian fishpond system, are located at Marine Corps Base Hawaii (MCBH) and part of the Nuʻupia Ponds Wildlife Management Area, a wetland refuge for native, endangered, and protected birds and Hawaiian green sea turtles, as well as many native fish species. Currently, there is uncertainty regarding the ecological status and condition of the fishponds following prior modification of wetland habitats in and around the ponds. This study examines circulation dynamics and characterizes water exchange, pond volume, and residence time across the full tidal spectrum at Nuʻupia fishponds. Our results indicate a general west to east gradient in current flow; with higher flushing rates and lower residence times of fishponds in the western ponds of the Nu’upia system compared to the eastern ponds. We further found low flushing rates at several sites causing limited water exchange with Kāne’ohe Bay, as well as within Nu’upia Pond system. Sufficient water circulation plays a fundamental role in maintaining a healthy balance of fishpond flora and fauna and preserve ecosystem health. The results from this study provide a baseline of current physical water circulation dynamics and implications for ecosystem health, as well as inform science-based conservation and management strategies moving forward.

Stroke causes disability and significantly affects patient quality of life. Post-stroke rehabilitation of upper limb function is crucial, as it affects daily activities and individual autonomy. Traditional rehabilitation methods often require frequent visits to specialized centers, which can be costly and challenging. This study investigated the effectiveness of a home-based self-training device, "Kenko Yusuri," in improving upper limb function in patients with chronic stroke. This multicenter prospective intervention study used a quasi-randomized controlled trial design. Ninety-three outpatients from five hospitals in Japan were enrolled and assigned to either the intervention group who used the "Kenko Yusuri" device or the control group who underwent conventional rehabilitation. All patients received botulinum toxin type A (BoNT-A) injections to treat upper limb spasticity. The primary outcome measure was the Fugl-Meyer Assessment (FMA) of upper-extremity motor function. Secondary outcomes included the modified Ashworth scale (MAS) score, range of motion (ROM), and chronic pain assessments. The intervention group demonstrated significantly greater improvements in FMA total scores than the control group. Patients with moderate paralysis experienced the greatest benefits from the intervention. There were no significant between-group differences in MAS scores or ROM measurements. Pain and wrist ROM showed improvement in the intervention group. Home-based training with a shaking device significantly improved upper limb function in patients with moderate chronic post-stroke paralysis. This approach aligns with the principles of use-dependent plasticity and offers a feasible and cost-effective alternative to traditional rehabilitation methods.

Personalized cancer vaccines have emerged as a promising avenue for cancer treatment or prevention strategies. This approach targets the specific genetic alterations in individual patient’s tumors, offering a more personalized and effective treatment option. Previous studies have shown that generalized peptide vaccines targeting a limited scope of gene mutations are ineffective, emphasizing the need for personalized approaches. While studies have explored personalized mRNA vaccines, personalized peptide vaccines have not yet been studied in this context. Pancreatic ductal adenocarcinoma (PDAC) remains challenging in oncology, necessitating innovative therapeutic strategies. In this study, we developed a personalized peptide vaccine design methodology, employing RNA sequencing (RNAseq) to identify prevalent gene mutations underlying PDAC development in a specific patient solid tumor tissue. We performed RNAseq analysis for trimming adapters, read alignment, and somatic variant calling. We also developed a Python program, called GeneFinder, which validates the alignment of the RNAseq analysis. The Python program is freely available to download. Using chromosome number and locus data, GeneFinder identifies the target gene along the UCSC hg38 reference set. Based on the gene mutation data, we developed a personalized PDAC cancer vaccine that targets 100 highly prevalent gene mutations in the individual patient. We predicted peptide-MHC binding affinity, immunogenicity, antigenicity, allergenicity, and toxicity for each epitope. Then, we selected the top 50 and 100 epitopes based on our previously published vaccine design methodology. Finally, we generated pMHC-TCR 3D molecular model complex structures which are freely available fo download. The designed personalized cancer vaccine contains epitopes commonly found in PDAC solid tumor tissue. Our personalized vaccine was composed of neoantigens, allowing for a more precise and targeted immune response against cancer cells. Additionally, we identified mutated genes which were also found in the reference study where we obtained the sequencing data, thus validating our vaccine design methodology. This is the first study designing a personalized peptide vaccine using human patient data to identify gene mutations associated with the specific tumor of interest.

Urban air pollution is a significant threat to both the environment and public health. Primarily originating from traffic emissions, particulate matter is identified as the most prevalent and toxic pollutant in cities. In recent years, street vegetation has emerged as a nature-based solution to improve urban air quality. However, to achieve this goal, proper placement of vegetation is crucial. This study critically investigates how different street tree placement strategies affect the local air quality, based on a model calibrated using existing air quality measurements from one of the most polluted streets in Glasgow. We then test the local air quality effects of tree orientation, spacing, shape, porosity, size, species, and wind directions. The findings suggest that trees effectively enhance air quality, particularly when implemented on the leeward side of the street. To achieve optimal effectiveness, the spacing of trees require careful alignment with the aspect ratio, as haphazard planting could lead to unfavorable results. The insights on improving air quality in Glasgow's street canyons, complements the objectives of the ‘Glasgow Avenues Programme’ and can be included in its Low Emission Zones to co-benefit the environment and the wellbeing of the local community.

Artificial intelligence (AI), deep learning (DL) or machine learning (ML) is the ability of computer systems, machines and enginery to work devise procedures like humans. These technologies provide opportunities and possibilities to advance diagnostics and in planning also in the field of human medicine and dentistry. The purpose of this literature review was to ascertain the applicability and significance of AI, as well as to highlight its uses in maxillofacial surgery. The primary inclusion criterion for this publication was an original paper written in English focusing on the use of AI, DL or ML in maxillofacial surgery. The sources of information were PubMed, Scopus and Web of Science, and the queries were made on 31st of December 2023. The search strings used were “artificial intelligence maxillofacial surgery”, “machine learning maxillofacial surgery” and “deep learning maxillofacial surgery”. Following the removal of duplicates, all remaining publications that were returned by the searches and were screened by three independent operators to minimize the risk of bias. The analysis of publications from 1992 to 2023 identified certain records, of which 324 were finally selected. These were calculated according to the year of publication with a continuous increase (excluding 2012 and 2013) of R2 = 0.9295. Generally, in orthognathic dentistry and maxillofacial surgery, artificial intelligence and machine learning have gained popularity over the past few decades. When we included the keywords "planning in maxillofacial surgery" and "planning in orthognathic surgery", the set of published papers significantly increased to the number of 7535 publications. The first publication appeared in 1965, with an increasing trend (excluding 2014-2018), with an R2 value of 0.8642. These tools have been found useful for diagnosis, treatment planning in head and neck surgical oncology, cosmetic and aesthetic surgery, and in oral pathology. In orthognathic surgery, they have been utilised for diagnosis, treatment planning, assessment of treatment needs, cephalometric analyses, and orthognathic surgeries, among other applications. The review confirms that the current use of artificial intelligence and machine learning in maxillofacial surgery is focused mainly on the evaluation of digital diagnostic methods especially radiology, treatment plans and postoperative results. However, as these technologies are integrated in maxillofacial surgery and robotic surgery in head and neck region, it is expected that in the future they will be gradually utilized to plan and comprehensively evaluate the success of maxillofacial surgeries.

As the world attempts to decarbonise the food industry and limit greenhouse gas (GHG) emissions, plant-based meat analogues (PBMAs) have emerged as a sustainable alternative to traditional meat. This study implemented a life cycle assessment (LCA) to rigorously compare the environmental impacts of a beef burger (BB), produced with British beef, against a meat analogue (MA) equivalent with a publicly available recipe. For the LCA, a cradle-to-fork system boundary was utilised, alongside a functional unit of a single 100 g burger patty. Results from the LCA revealed that the BB patty had more than double the total environmental impact than the MA equivalent, as well as possessing a global warming impact that was 62% higher. A simple extrapolation illustrated that if the UK population switched from beef to meat analogue patties, 3 million tonnes of CO2e could be saved annually, corresponding to 0.74% of the country’s yearly territorial GHG emissions. Scenario analyses displayed how the environmental impact of the MA patty remained stable regardless of changes in exportation, ingredient origin or soy protein sourcing. Moreover, sensitivity analysis conducted with an alternative characterisation method corroborated initial findings, whilst uncertainty analysis ensured that nearly all conclusions generated from the original comparison were robust. Future studies should conduct peer-reviewed LCAs on PBMA patties with commercial recipes based on other plant-based proteins, as well as fully understanding any potential health implications of long-term PBMA consumption.

This research study focuses on addressing practical optimization challenges in audio-visual content using advanced computational intelligence methods, with a specific emphasis on privacy-preserving issues. The research will be presented as a proposal and can be conducted based on the provided ideas. Computational intelligence encompasses various approaches, including evolutionary algorithms, learning methods, fuzzy systems, and neural networks, which have become essential tools for tackling complex engineering optimization problems due to computational expenses, dimensional complexities, and interdisciplinary integration. The research objectives include a thorough investigation of optimization challenges in audio-visual content, the delineation of problem characteristics, and the development of relevant methodologies based on these specifications. The main goals of the study, titled "Advanced Computational Intelligence Assisted Less-Expensive Privacy-Preserving Optimization," encompass the development of a metamodel-based learning algorithm integrated with evolutionary computation for privacy-preserving optimization, less-expensive signal watermarking optimization using hybrid metamodeling and evolutionary algorithms, and a closed-loop robust intelligent PID control system applied in real-time dynamic signal watermarking. Additional objectives may be defined as the research progresses and further background review is conducted.

Wastewater-Based Epidemiology (WBE) is currently used to monitor not only the spread of the pandemic virus SARS-CoV-2 but also for other viruses in endemic conditions, particularly in the absence of syndromic surveillance. Continuous monitoring of sewage requires high costs and significant time investment, highlighting the need for standardized methods and structured monitoring strategies. In this context, we conducted weekly wastewater monitoring in northwestern Italy, targeting Human Adenovirus (HAdV), Norovirus Genogroup II (NoVggII), Enterovirus (EV), and SARS-CoV-2. Samples collected at the entrance of treatment plants were concentrated using PEG/NaCl precipitation and viral nucleic acids were extracted and detected by real-time (RT-)qPCR. NoVggII resulted the most identified target (84.4%), followed by HAdV, SARS-CoV-2, and EV. Only HAdV and EV exhibited seasonal peaks in spring and summer. SARS-CoV-2 results compared with data previously collected in the same study area (February 2021 to September 2021) revealed a shift from an epidemic to a pandemic status, likely due to the evolution of variants. In conclusion, WBE, using standardized methods and an efficient monitoring strategy, proves valuable for virus surveillance in pandemic and epidemic scenarios, enabling the identification of temporal-local distribution patterns that are useful for making informed public health decision.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

Machine learning has become more prevalent as a tool used for biogeochemical analysis in agricultural management. However, a common drawback of machine learning models is the lack of interpretability, as they are black boxes that provide little insight into agricultural management. To overcome this limitation, we compared three tree-based models (decision tree, random forest, and gradient boosting) to explain soil organic matter content through Shapley additive explanations (SHAP). Here, we used nationwide data on field crops, soil, terrain, and climate across South Korea (n = 9,584). Using the SHAP method, we identified common primary controls of the models, for example, regions with precipitation levels above 1400 mm and exchangeable potassium levels exceeding 1 cmol+ kg-1, which favor enhanced organic matter in the soil. Different models identified different impacts of nutrients on the organic matter level in the soil. The SHAP method is practical for assessing whether different machine learning models yield consistent findings in addressing these inquiries. Increasing the explainability of these models means determining essential variables related to soil organic matter management and understanding their associations for specific instances.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn &gt;30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

There is a great need to develop research-based models for supporting collaboration between educational institutions. Collaboration models are needed, for example, to assist the transition from lower educational level to higher education or from higher education to work life. In this research, collaboration was conducted through a joint upper-secondary school and university course that addressed global challenges by using a project-based learning approach. There is a shortage of research exploring students’ perceptions of collaboration. Therefore, the main purpose of this qualitative case study is to explore the relevance of the joint course for students and university students. The research was guided by the following research question: What kind of relevance did the students experience in the joint project-based learning course? The data was gathered using questionnaires, interviews, and reflective study reports. The data was analyzed via theory-based content analysis where research-oriented relevance model was used as the analysis framework. The analysis framework enabled categorizing experienced relevance on individual, vocational and societal dimensions. Altogether, the analysis produced 7 relevance categories for upper-secondary students and 9 for university students. According to the analysis, upper-secondary school students felt that the course offered the most on an individual relevance dimension whereas university students experienced the vocational relevance dimension most diverse. As the main conclusion, this research produced new insights on the experienced relevance of upper-secondary level and higher education cooperation from the students’ point of view. The acquired knowledge can be useful for everyone developing new cross-institutional cooperation models.

In the paper we present a new test for comparison of the means of multivariate samples with unknown distributions. The test is based on the comparison of the distributions of the distances between the samples’ elements and their means using univariate two-sample Kolmogorov-Smirnov test. The activity of the suggested method is illustrated by numerical analysis of the real-world and simulated data.

The prevalent use of synthetic chemical rodenticides (both 1st or 2nd generation anticoagulants and acute rodenticides) is the primary method for managing rodents in sub-Saharan Africa. However, this practice poses substantial health and environmental risks and often fails to yield significant, sustainable reductions in rodent pest populations. In this paper, the second one of a two-part series, we advocate for a more responsible and sustainable approach to rodent management in urban and agricultural settings in sub-Saharan Africa. We propose a shift towards environmentally friendly rodent management strategies, specifically emphasizing the adoption of Ecologically-Based Rodent Management (EBRM) as a viable alternative to synthetic chemical rodenticides. EBRM relies on a comprehensive understanding of pest rodent biology, ecology, and behavior, along with the implementation of a range of community-based interventions. These actions are designed to ensure the consistent reduction of rodent pest populations to economically and hygienically acceptable levels. By embracing EBRM, we not only anticipate a reduction in the social impacts of pest rodents in a cost-effective manner but also a significant decrease in the risks posed by rodents and synthetic chemical rodenticides to human health and the environment. This paradigm shift towards EBRM promises a more sustainable and responsible approach to rodent management in sub-Saharan Africa.

A bridged 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative (PN-DOPO) in combination with aluminum phosphates coated sepiolite (Sep@AlPO4) was used to improve the flame retardancy, thermal stability and mechanical properties of poly (ethylene oxide) (PEO)/poly (butylene adipate-co-terephthalate) (PBAT) blends. The synergistic effects of PN-DOPO and Sep@AlPO4 on the fire resistance, thermal decomposition behavior and mechanical properties of PEO/PBAT composites were investigated systematically. The results indicated that 5 wt % Sep@AlPO4 combined with 10 wt% PN-DOPO into PEO/PBAT achieved a V-1 rating in UL-94 test and the LOI value increased to 23.7%, meanwhile, the peak-heat release rate (p-HRR), av-HRR and total heat release (THR) values of PEO/PBAT/PN10%/Sep5% composites decreased by 35.6%, 11.0% and 23.0% compared with those of PEO/PBAT, respectively. The thermogravimetric analysis (TGA) results confirmed that PN-DOPO/Sep@AlPO4 could enhance the initial thermal stability and char yield of PEO/PBAT matrix, and TGA/Fourier transform infrared spectrometry (TGA-FTIR) results revealed that the composites exhibited the absorption peaks of phosphorous-containing groups and an increase in gas-phase volatiles during the thermal decomposition process. The digital photographs and morphological structures of char residues demonstrated that PN-DOPO and Sep@AlPO4 mixtures benefited to the formation of a more continuous and dense carbon layer on the composites surface during combustion. Rheological behavior revealed that a higher storage modulus, loss modulus and complex viscosity of PEO/PBAT/PN-DOPO/Sep@AlPO4 composites could also promote the cross-linking structure during burning. Furthermore, the PEO/PBAT/PN-DOPO/Sep@AlPO4 composites exhibited excellent mechanical properties in terms of elongation at break and flexural performance than the PEO/PBAT system. All the results demonstrated that PEO/PBAT system modified by the combination of PN-DOPO and Sep@AlPO4 not only exhibited excellent synergistic effect on the flame retardance, but also had good improvement on thermal stability and mechanical properties, indicating the potential application in areas requiring fire safety.

Persistent human papillomavirus (HPV) infection is responsible for practically all cervical and a high proportion of anogenital and oropharyngeal cancers. Therapeutic HPV vaccines in clinical development show great promise in improving outcomes for patients who mount an anti-HPV T cell response, but far from all patients elicit a sufficient immunological response. This witnesses a translational gap between animal models and human patients. Here, we investigated the potential of a new assay consisting of co-culturing vaccine-transduced dendritic cells (DCs) with syngeneic healthy human peripheral blood mononuclear cells (PBMCs) to mimic a human in vivo immunization. This new promising human ex vivo PBMC assay was evaluated using an innovative therapeutic adenovirus (Adv)-based HPV vaccine encoding the E1, E2, E6, and E7 HPV16 genes. This new method allowed us to show that vaccine-transduced DCs yielded functional effector T cells and unveiled information on immunohierarchy showing E1-specific T cell immunodominance over time. We suggest that this assay can be a valuable translational tool to complement the known animal models, not only for HPV therapeutic vaccines, and supports the use of E1 as an immunotherapeutic target. Nevertheless, the findings reported here need to be validated in a larger number of donors, and preferably in patient samples.

With the engineering system becoming more and more complex, the uncertainty factors have a more and more profound influence on the reliability and security of the engineering system. In recent years, Reliability-Based Design Optimization (RBDO) has been studied extensively in complex engineering system design. The research on reliability optimization design considering stochastic uncertainty has been comprehensive and widely used. However, the reliability optimization design considering mixed uncertainty has the disadvantages of large computation and imprecise convergence. This study proposes an RBDO method based on Particle Swarm Optimization (PSO) and Simulated Annealing (SA) to overcome this challenge. In the method, PSO is used to solve the most probable point, while SA has excellent global optimization capability to acquire the global optimal solution. Finally, three examples are given to illustrate the advantages of the proposed method.

Empowering teachers with Critical Thinking and understanding of sustainability is vital for guiding students’ informed decisions and actions in today’s world. Higher education needs innovative, student-centered methods like case-based teaching in order to promote Critical Thinking and the principles of Education for Sustainable Development. The aim of the study was to explore and evaluate pre-service teachers' Critical Thinking when engaged with case studies in a practicum preparation course centered on Education for Sustainable Development. Nine undergraduate students in Teacher Education participated in the study and answered four case studies. The case studies’ responses were analyzed through a bottom-up content analysis revealing eight higher-order categories. While approaching the case studies, student-teachers followed thinking processes similar to the processes proposed by the iterative models of Critical Thinking as perceived by Garrison (1991) and/or Brookfield (1987). Nevertheless, in some cases, pre-service teachers’ disengagement was evident. The rubric assessment highlighted that the responses fell under three profiles, namely the “Deficient Critical Thinker”, the “Emerging Critical Thinker” and the “Competent Critical Thinker”. The findings emphasize the need for targeted and individualized teaching interventions in teacher higher education programs aiming at Education for Sustainable Development complying with the learning needs of student-teachers’ Critical Thinking profiles.

A clinical simulation web-based program, known as FIRST2ACT (Feedback Incorporating Review and Simulation Techniques to Act on Clinical Trends) is designed to increase the efficacy of cli-nicians’ actions in the recognition and immediate response to a patient’s deterioration. This study, which was nested in a larger mixed method project, used ten focus groups (n=65) of graduate, enrolled, registered nurses, Associate Nurse Unit Managers, and general manag-ers/educators/coordinators from four different institutions to investigate whether nurses felt their practice was influenced by participating in either a face-to-face or web-based simulation educa-tional programme about patient deterioration. Results indicate individuals who were less ‘tech-savvy’ appreciated the flexibility of web-based learning, which increased their confidence. Face-to-face students appreciated self-reflection through performance evaluation. While face-to-face simulations were unable to completely duplicate symptoms, they did show nurses' adaptability. Both interventions enhanced clinical practice by improving documentation and re-plies while also boosting confidence and competence. Web learners initially experienced tech-related anxiety, which gradually subsided, demonstrating healthcare professionals' resilience to new learning approaches. Overall, the study highlighted the advantages and challenges of web-based and face-to-face education in clinical practice, emphasising the importance of adapta-bility and reflective learning for healthcare professionals. Further exploration of specific topics is required to improve practice, encourage knowledge sharing among colleagues, and improve early detection of patient deterioration.

Cellular organisms possess intricate DNA damage repair and tolerance pathways to manage various DNA lesions arising from endogenous or exogenous sources. Dysregulation of these pathways is associated with cancer development and progression. Synthetic lethality (SL), a promising cancer therapy concept, involves exploiting the simultaneous functional loss of two genes for selective cell death. PARP inhibitors (PARPis) have demonstrated success in BRCA-deficient tumors. Cisplatin (CPT), a widely used chemotherapy agent, forms DNA adducts and crosslinks, rendering it effective against various cancers but less so for prostate cancer (PCa) due to resistance and toxicity. Here, we explore the therapeutic potential of TLK1, a kinase upregulated in androgen-insensitive PCa cells, as a target for enhancing CPT-based therapy. TLK1 phosphorylates key homologous recombination repair (HRR) proteins RAD54L and RAD54B, critical for HRR alongside RAD51. The combination of CPT with TLK1 inhibitor J54 exhibits SL in androgen-insensitive PCa cells. The formation of double-strand break intermediates during inter-strand crosslink processing necessitates HRR for effective repair. Therefore, targeting TLK1 with J54 enhances the SL of CPT by impeding HRR, leading to increased sensitivity in PCa cells. These findings suggest a promising approach for improving CPT-based therapies in PCa, particularly in androgen-insensitive cases. By elucidating the role of TLK1 in CPT resistance, this study provides valuable insights into potential therapeutic targets to overcome PCa resistance to CPT chemotherapy. Further investigations into TLK1 inhibition in combination with other DNA-damaging agents may pave the way for more effective and targeted treatments for PCa and other cancers that exhibit resistance to traditional chemotherapy agents.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

We assessed the use of Evidence-Based Practice (EBP) among pharmacists working in community pharmacies in France, and the factors linked to this practice. During 3 months in 2018 an online survey was sent to over 7,000 active pharmacists, and posted on pharmacist social media sites. The 40-item questionnaire described four clinical cases reflecting typical situations (conventional med-icine and Complementary and Alternative Medicine) encountered daily by community pharma-cists. Multiple-choice responses were proposed and scored according to whether they reflected EBP. A high total score indicated behavior in line with EBP. Univariate and multivariate analyses were used to evaluate factors that might explain adherence to EPB (pharmacy’s characteristics, the pharmacist’s status, mode of continuing education and sources of information). 595 pharmacists completed the questionnaire. The majority relied on pharmaceutical industry and other biased and/or non-evidence-based sources, particularly concerning information on homeopathic products. The consultation of independent reviews, health agency recommendations, and peer-reviewed scientific journals, was associated with evidence-based decisions. In contrast, reliance on phar-maceutical industry documents, personal experience and informal handbooks was linked to lower EBP scores. The level of EBP use by French community pharmacists needs to be improved to ensure that good quality scientifically-based advice is given to customers.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

Abstract: Filipendula ulmaria, commonly known as meadowsweet, is a wild herbaceous flowering plant widely distributed in Europe. A range of salicylic acid derivatives and flavonol glycosides have been previously associated with the antirheumatic and diuretic properties of F. ulmaria. In the present work, an hydroalcoholic extract of F. ulmaria aerial parts was extensively profiled using an efficient NMR-based dereplication strategy. The approach involves fractionation of the crude extract by centrifugal partition chromatography (CPC), ¹³C NMR analysis of the fractions, 2D-cluster mapping of the whole NMR dataset and finally, structure elucidation using a natural metabolite database, validated by 2D NMR data interpretation and liquid chromatography coupled to mass spectrometry. The chemodiversity of the aerial parts was quite broad, with 28 compounds unambiguously identified, belonging to various biosynthetic classes. The F.ulmaria extract and CPC fractions were screened for their potential to improve skin epidermal barrier function and also skin renewal properties using in vitro assays performed on Normal Human Epidermal Keratinocytes. Fractions containing quercetin, kaempferol glycosides, ursolic acid, pomolic acid, naringenin, β-sitosterol, and tellimagrandins I and II were found to be responsible for the up-regulation of genes related to skin barrier function, epidermal renewal and stress responses. This research is significant as it could provide a natural solution for improving hydration and skin renewal properties.

Background and Objectives: Elders’ needs are rarely examined beforehand, and thus, although technology-based tools can enhance self-management, acceptability rates are still low. This study aimed to examine and compare self-reported needs, priorities, and preferences of elders with heart failure (HF), diabetes mellitus (DM), and chronic obstructive pulmonary disease (COPD) toward technology use to enhance self-management. Materials and Methods: A convenience sample of 473 participants over 60s (60.5% females), diagnosed with HF (N=156), DM (N=164), or COPD (N=153) was recruited. They were administered a questionnaire about the usefulness of technology in general and in specific areas of disease management. Results: Most participants (84.7%) admitted that technology is needed for better disease management. This was equally recognized across the three groups both for the overall and specific areas of disease management (in order of priority: ‘Information’, ‘Communication with Physicians &amp; Caregivers’, and ‘Quality of Life &amp; Wellbeing’). Sociodemographic differences were found. Cell phones and PCs were the devices of preference. The four common features prioritized by all three groups were related to ‘information about disease management’ (i.e., monitoring symptoms, reminders for medication intake, management and prevention of complications), whereas the fifth one was related to ‘communication with physicians and caregivers (i.e., in case of abnormal or critical signs). The top disease-specific feature was also monitoring systems (of respiratory rate or blood sugar or blood pressure, oxygen), whereas other disease-specific features followed (i.e., maintaining normal weight for HF patients, adjusting insulin dose for DM patients, and training on breathing exercises for COPD patients). Conclusions: Elders in these three samples seem receptive to technology in disease management. mHealth tools, incorporating both common and disease-specific features and addressing different chronic patients, and being personalized at the same time, could be cost-saving and useful adjuncts in routine clinical care to improve self-management.

Wildlife tourism and wildlife trade may appear juxtaposed, but are two, potentially aligning, income generators that could benefit conservation in developing countries. Utilising data sets collated from Madagascar’s Ministère du Tourisme and CITES respectively for the period 2007 to 2018, this study estimated levels of income from wildlife tourism and wildlife trade for Madagascar. Between 2007-2018, tourism reported yearly incomes ranging from a low of US $1.4 million up to a high of US $15.7 million. However, it was unclear what percentage of this figure flowed to benefit local communities. Alternatively, using reported networks for the live wildlife trade, the estimated economic value reaching collectors and/or intermediaries on Madagascar was US $72,299.80 for the period 2007 to 2018. Both revenue generators operated within different geographical areas, with tourism opportunities presenting themselves to communities adjacent NPs, while wildlife trade networks were not restricted to NPs and operated sporadically across Madagascar. Hence, the economic benefits reached different Malagasy participants across the country. The management of both activities needs great care to ensure that environmental impacts and sustainability are core measures on any such activities. Whilst this study shines light on economic values and novel perspectives regarding these two trade types, it also highlighted knowledge gaps. Thus, indicating where much greater research attentions was required to allow better understanding of the specific benefits and risks from engaging with both trade types for local Malagasy people and their environments.

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

Animal research has always been crucial for various medical and scientific breakthroughs, providing information on disease mechanisms, genetic predisposition to diseases, and pharmacological treatment. However, the use of animals in medical research is a source of great controversy and ongoing debate in modern science. To ensure a high level of bioethics, new guidelines have been adopted to replace animal testing wherever possible, reduce the number of animals per experiment, and refine procedures to minimize stress and pain. Supporting these guidelines, this article proposes a novel approach for unobtrusive, continuous, and automated monitoring of the respiratory rate of laboratory rats. It uses the cyclical expansion and contraction of the rats’ thorax/abdominal region to determine this physiological parameter. In contrast to previous work, the focus is on unconstrained animals, which requires the algorithms to be especially robust to motion artifacts. To test the feasibility of the proposed approach, video material of multiple rats was recorded and evaluated. High agreement was obtained between RGB-imaging and the reference method (respiratory rate derived from electrocardiography), which was reflected in a relative error of 5.46%. The current work shows that camera-based technologies are promising and relevant alternatives for monitoring the respiratory rate of unconstrained rats, contributing to the development of new alternatives for continuous and objective assessment of animal welfare and hereby guiding the way to modern and bioethical research.

Linear programming formulations of forest ecosystem management (FEM) problems proposed in the 60s have been adapted and improved upon over the years. Generating management alternatives for forest management planning is a key step in building these models. Global forests are diverse, and a variety of models have been developed to simulate management alternatives. Climate change has made forest management calculations even more complex, requiring flexibility, diverse parameters, models, and methods. Despite this complexity, consistent concepts can be applied in developing management alternatives for forest management planning. This work describes iGen, a flexible forest prescription generator that applies the AI technique Rule-Based System (AI-RBS). iGen projects the state and associated inputs and outputs for a set of management units using rules from its knowledge base. An Inference Engine uses the rules to simulate a set of prescriptions in a tree-like graph structure. Without needing IT specialists, forest managers can describe the potential development of their forest through variables, rules, formulas, functions, and procedures. A key feature of iGen is that it is not limited to, adapted to, or focused on any specific region, landscape, forest condition, projection method, or yield function. Instead, it aims to maximize generality, enabling it to address a broad range of FEM problems. This article introduces iGen, explaining its concepts, structure, and algorithms through two FEM problems: natural regeneration with shelterwood harvests and plantation/coppice. For data and iGen source programs, visit github.com/…/iGen.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

Water hyacinth (Eichhornia crassipes) is a potential accumulator of water pollutants in aquatic ecosystems, and its presence in water systems can affect water quality. This study used different field measurements and laboratory tests of Lake Water to determine the impact of water hyacinth phytoremediation capacity. A total of eight sampling stations used for the two lakes; Lake Koka and Lake Ziway. Sampling stations were selected from sites infested with water hyacinth (low, medium and high) and non-water hyacinth aquatic plants during wet and dry seasons to compare the effects of plants on water quality in the two lakes. All the sampled stations had various human interventions. The water samples were tested for the selected physico-chemical properties namely phosphate, nitrate, pH, electrical conductivity (EC), Biological oxygen demand (BOD5), temperature, and heavy metals (Chromium (Cr), Lead (Pb), Cadmium (Cd), Zinc (Zn), and Copper (Cu). These water quality variables were compared by means of ANOVA. Despite the COD of Lake Ziway, this study found no significant (p &gt; 0.05) variation in the concentrations of Cu, EC, pH and temperature between wet and dry seasons in either lake. Variations in Zn concentration and other physico-chemical parameters (EC, BOD, COD, nitrate, phosphate) between low, medium and high levels of water hyacinth were significant in both lakes (p&lt;0.05). Water hyacinth has shown significant phytoremediation nature during wet and dry seasons. The lowest average heavy metal, phosphate, and nitrate concentrations; and significant pH and temperature variations were observed in Lakes Koka and Lake Ziway, among water hyacinth and other grass-infested sites.

Nowadays, the European Union and the governments of the different countries have focused on the development of the Sustainable Development Goals (SDG) and the 2030 agenda, something that has been translated into education itself. Video Games, Gamification, and Game Based Learning have become different strategies and tools to enhance the learning process and some of the growing approaches used by teachers to develop sustainable education in the classrooms. This research aims to analyze the characteristics to promote sustainability in education using games and technology, specifically its learning benefits for Higher Education. A systematic review of the literature was conducted following the PRISMA methodology. At first, 2025 documents were found which, after the filtering phases, the number of articles has been reduced to nine, which subsequently were analyzed in depth. The results indicated that among the benefits of the use of games mediated by technologies are the following: it favors education for sustainability and it promotes the educational inclusion and the work of various social skills such as collaborative and cooperative work. Also, showed an increase of the number of publications between 2019 and 2023, reflecting the growing interest in the topic. However, there are some research gap in this field.

In today's business world, many companies have realized that consumer feedback evaluations play a crucial part in shaping the company's future activities. The hotel and tourism industries are well-known examples where the user feedback has become crucial. Even though most accommodations want their clients to express their opinions about their services, these reviews are nevertheless carefully reviewed by them. This manual approach is time demanding and error prone, the level of expertise of the individual analyzing the evaluations determines the quality of the manual analysis. This research focuses on the development of a tool-based support system that analyzes text-based customer evaluations and then highlights the maintenance issues identified in the reviews, removing the need to manually evaluate and analyze the customer reviews. The process includes data preparation, sentiment analysis, and a fully trained deep learning model to extract critical insights. Using sentiment analysis techniques after data preprocessing and trained deep learning model, an accuracy of 96% was achieved, and this paper discusses how this technology helps to meet the needs of accommodation management by completing activities efficiently. This might save management time and helps to save money without losing clients, allowing them to enhance their additional sales.

In today's business world, many companies have realized that consumer feedback evaluations play a crucial part in shaping the company's future activities. The hotel and tourism industries are well-known examples where the user feedback has become crucial. Even though most accommodations want their clients to express their opinions about their services, these reviews are nevertheless carefully reviewed by them. This manual approach is time demanding and error prone, the level of expertise of the individual analyzing the evaluations determines the quality of the manual analysis. This research focuses on the development of a tool-based support system that analyzes text-based customer evaluations and then highlights the maintenance issues identified in the reviews, removing the need to manually evaluate and analyze the customer reviews. The process includes data preparation, sentiment analysis, and a fully trained deep learning model to extract critical insights. Using sentiment analysis techniques after data preprocessing and trained deep learning model, an accuracy of 96\% was achieved, and this paper discusses how this technology helps to meet the needs of accommodation management by completing activities efficiently. This might save management time and helps to save money without losing clients, allowing them to enhance their additional sales.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

Artificial intelligence’s rapid advancement has enabled various applications, including intelligent video surveillance systems, assisted living, and human-computer interaction. These applications often require one core task: video-based human action recognition. Research in human video-based human action recognition is vast and ongoing, making it difficult to assess the full scope of available methods and current trends. This survey provides an in-depth exploration of the vision-based human action recognition field, comprehensively offering the available techniques and their evolution, highlighting the cutting-edge ideas driving its development. We also analyze the most used keywords in research papers over the past years to identify trends and predict possible future directions. Hence, this concise survey helps researchers understand the breadth of existing approaches, evaluate current research trends, and stay up-to-date on potential developments.

The threat posed by climate change, the progressive erosion of natural resources, the polluting effects related to private motorization, energy waste, excessive consumption of agricultural and natural soils and their progressive waterproofing and reduction in vegetation cover, with the subsequent environmental degradation, have highlighted the need for a sustainable management of natural resources, in terms of an equitable and ethical development, to build inclusive communities able to adapt to the negative effects of emergency phenomena, through new capacities of economic, cultural and social resilience. This contribution presents the results of the activities conducted in the RivEr/Generation_LAB, a project organized by three CIVIS members (Sapienza University of Rome, Universitè libre de Bruxelles, Universidad Autonoma de Madrid) as a part of the CIVIS Project "RivEr/Generation_LAB. Linking resilience with inclusiveness in the urban built environment of Rome, Brussels, and Madrid", financed into the Hub4 Cities, Territories &amp; Mobilities’ Call for proposals 2021. The project proposes a methodology of intervention in the Flaminio district, in particular on the 'Olympic Village' and its relationship with the Tiber River, in line with the Sustainable Development Goals, the Millennium Ecosystem Assessment and the New European Bauhaus, to establish new relationships between cities and the natural environment, favouring sustainable and inclusive public spaces.

This work considers the task of representation learning on the attributed relational graph (ARG). Both the nodes and edges in an ARG are associated with attributes/features allowing ARGs to encode rich structural information widely observed in real applications. Existing graph neural networks offer limited ability to capture complex interactions within local structural contexts, which hinders them from taking advantage of the expression power of ARGs. We propose Motif Convolution Module (MCM), a new motif-based graph representation learning technique to better utilize local structural information. The ability to handle continuous edge and node features is one of MCM’s advantages over existing motif-based models. MCM builds a motif vocabulary in an unsupervised way and deploys a novel motif convolution operation to extract the local structural context of individual nodes, which is then used to learn higher-level node representations via multilayer perceptron and/or message passing in graph neural networks. When compared with other graph learning approaches to classifying synthetic graphs, our approach is substantially better in capturing structural context. We also demonstrate the performance and explainability advantages of our approach by applying it to several molecular benchmarks.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

Passive and forced drinking harm was prevalent but less recognized in Chinese adolescents. We educated adolescents on such harm to reduce their intention to drink. Students (n=1244) from 7 secondary schools in Hong Kong participated in a video-based health talk on passive and forced drinking harm. Paired t-test was used to assess their change in knowledge of passive and forced drinking, health and social harm of drinking after the health talk. McNemar's chi-squared test and adjusted multivariable logistic regression (AOR) were used to assess their change in intention to drink and intention to quit. Students were less likely to drink (OR 0.29, 95% CI 0.19-0.42) and more likely to quit drinking (OR 3.50, 1.10-14.6) after the health talk. Increased knowledge of passive drinking was associated with less intention to drink (AOR 0.93, 0.90-0.97), increased knowledge of health harm (adjusted b 0.06, 0.05-0.08), and social harm of drinking (adjusted b 0.12, 0.10-0.16). Similar associations were observed in forced drinking (intention to drink: AOR 0.87, 0.79-0.96; health harm: adjusted b 0.16, 0.12-0.19; social harm: adjusted b 0.36, 0.28-0.43). We showed preliminary evidence that the health talk on passive and forced drinking reduced the intention to drink in adolescents.

Coastal areas are highly vulnerable to climate change hazards (e.g., sea-level rise, flooding, coastal erosion), which can lead to significant impacts at the ecosystem and societal level. Interest in Ecosystem-based Adaptation (EbA) is gaining importance due to its potential multiple benefits, including social and environmental aspects, when compared to more traditional approaches such as hard engineering interventions. When assessing EbA strategies, further understanding of the nature-society functions, processes, values, and benefits is needed to increase its application. This study contributes to a better knowledge of EbA by developing a systematic literature review of studies performing socio-economic assessments of climate change adaptation in coastal areas. The analysis of 54 publications revealed that most of the studies assessed adaptation solutions through cost-benefit analysis, followed by multi-criteria analysis, and other techniques. Hybrid adaptation strategies based on different combinations of hard, soft and EbA interventions were considered as potential optimal solutions in a significant part of the assessments. This study suggests the potential co-benefits of EbA in the form of ecosystem services, livelihood diversification or biodiversity conservation, but also stresses the need for further research on this topic, as well as on evaluating how EbA perform in the long-term under climate changing conditions scenarios.

Grinding processes’ stochastic nature poses a challenge in predicting the quality of the resulting surfaces. Post-production measurements for form, surface roughness, and circumferential waviness are commonly performed due to infeasibility in measuring all quality parameters during the grinding operation. Therefore, it is challenging to diagnose the root cause of quality deviations in real-time resulting from variations in the machine’s operating condition. This paper introduces a novel approach to predicting the overall quality of the individual parts. The grinder is equipped with sensors to implement condition-based maintenance and is induced with five frequently occurring failure conditions for the experimental test runs. The crucial quality parameters are measured for the produced parts. Fuzzy c-means (FCM) and Hotelling’s T-squared (T2) have been evaluated to generate quality labels from the multi-variate quality data. Benchmarked random forest regression models are trained using fault diagnosis feature set and quality labels. Quality labels from the T2 statistic of quality parameters are preferred over FCM approach for their repeatability. The model, trained from T2 labels achieves more than 94% accuracy when compared to the measured ring disposition. The predicted overall quality using the sensors’ feature set is compared against the threshold to reach a trustworthy maintenance decision.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

In this work, we have developed a non-ordinary state-based peridynamic model for multiple crack initiation and propagation due to compression-compression fatigue load. In each loading cycle, the fatigue loading is redistributed among the peridynamic solid body, leading to the progressive fatigue damage initiation and propagation in an autonomous fashion. The proposed fatigue model parameters are firstly validated by 3D numerical benchmark tests, and then it is applied to simulate widespread fatigue damage evolution of the aircraft wing corner box. The modified constitutive damage model has been implemented into the peridynamics framework at finite strain. Furthermore, the criterion algorithm from multiple initiation to propagation is discussed. It is shown that the numerical results obtained from peridynamics simulations are in general agreement with those from the experiment data. The comparison of experimental and numerical results indicates that the proposed non-ordinary state-based peridynamics fatigue model has the ability to capture the multiple crack initiation and propagation and other features of the aluminium alloy material.

The acquired immunodeficiency syndrome (AIDS) caused by the human immunodeficiency virus (HIV) continues to be a public health problem. In 2020, 680,000 people died from HIV-related causes, and 1.5 million people were infected. Antiretrovirals are only a way to control HIV infection but not to cure AIDS. As such, effective treatment must be developed to control AIDS. Developing a drug is not an easy task, and there is an enormous amount of work and economic resources invested. For this reason, it is highly convenient to employ computer-aided drug design methods, which can help generate and identify novel molecules. Using the de novo design, new novel molecules can be developed using fragments as building blocks. In this work, we develop a virtual-focused compound library of HIV-1 viral protease inhibitors from natural product fragments. Natural products are characterized by a large diversity of functional groups, many sp3 atoms, and chiral centers. Pseudo-natural products are a combination of natural products fragments that keep the desired structural characteristics from different natural products. An interactive version of chemical space visualization of virtual compounds focused on HIV-1 viral protease inhibitors from natural product fragments is freely available at https://figshare.com/s/ceb58d58e8f5585ce67e.

Telehealth is the delivery of many health care services and technologies to individuals at different geographical areas and is categorized as asynchronously or synchronously. The coronavirus disease 2019 (COVID-19) pandemic has caused major disruptions in health care delivery to breast cancer (BCa) patients and there is increasing demand for telehealth services. Globally, telehealth has become an essential means of communication between patient and health care provider. The application of telehealth to the treatment of BCa patients is evolving and increasingly research has demonstrated its feasibility and effectiveness in improving clinical, psychological and social outcomes. Two areas of telehealth that have significantly grown in the past decade and particularly since the beginning of the COVID-19 pandemic are telerehabilitation and teleoncology. There two technological systems provides opportunities at every stage of the cancer care continuum for BCa patients. We conducted a systematic literature review that examined the use of telehealth services via its various modes of delivery among BCa patients particularly in areas of screening, diagnosis, treatment modalities, as well as satisfaction among patients and health care professionals. The advantages of telehealth models of service and delivery challenges in delivery to patients in remote arears are discussed.

During the COVID-19 outbreak, most university courses have been offered on online platforms. A sudden shift from face-to-face classroom learning to online formats could influence the learning effectiveness of classes. This study aims to investigate differences in the learning effectiveness of online and face-to-face lecture courses. It also explores factors that impact the effectiveness of online instruction. These factors include interactions among learners, interactions between learners and the instructor, the quality of online platforms, learners’ ability to use devices and follow instructions, and learners’ situational challenges. The study participants were 261 university students at King Mongkut’s University of Technology Thonburi in Bangkok, Thailand. All participants were enrolled in at least one lecture course, such as history, humans and the environment, the environment and development, or general philosophy, during the 2019 academic year. A questionnaire was distributed to participants after they completed these courses in May 2020. Paired simple t-test analyses were used to compare the effectiveness of online and face-to-face classes, and a multiple regression analysis was used to identify factors that impact the learning effectiveness of online classes. The results show that online classes are less effective than face-to-face courses. The multiple regression analysis also revealed that the effectiveness of online learning was significantly impacted by learners’ ability to interact with classmates during class, their ability to interact with instructors after the class, the quality of online platforms, and disturbances or distractions in learners’ environments.

In the last five years, European research and innovation programmes have prioritised the development of online catalogues and tools (handbooks, models, etc.) to facilitate the implementation and monitoring of Nature Based Solutions (NBS). However, only a few catalogues and toolkits within European programmes are directly related to mainstreaming of NBS for food production (i.e., edible NBS). Therefore, the main aim of this paper is to present existing NBS tools through the eyes of productive urban landscapes. We reviewed 32 projects related to NBS and 50 tools were identified and characterised. Then, the 6 tools already available, and providing indicators, were further analysed in terms of their format and knowledge domains. Our main conclusion demonstrates that there is a lack of tools capable of supporting users for planning and implementing edible NBS, calculating the food potential of the city and/or of individual edible NBS, including the needed resources for implementation and operation (water, nutrients, energy), and assessing their urban design value, environmental and socio-economic impacts. And when they do exist, there is a resistance to share the models and equations behind the tools to allow other projects to reuse or validate them, fact which is contrary to Open Science principles stood up by many research public agencies.

BODIPY dyes have recently raised attention as potential photosensitizers. In this work, commercial and novel photosensitizers (PSs) based on BODIPY chromophores (haloBODIPYs and orthogonal dimers strategically designed with intense bands in the blue, green or red region of the Visible spectra and high singlet oxygen production) were covalently linked to mesoporous silica nanoparticles (MSNs) further functionalized with PEG and folic acid (FA). MSNs of approximately 50 nm in size with different functional groups were synthesized to allow multiple alternatives of PS-PEG-FA decoration of their external surface. Different combinations varying the type of PS (commercial Rose Bengal, Thionine and Chlorine e6 or custom-made BODIPY-based), the linkage design and the length of PEG are detailed. All the nanosystems were physicochemically characterized (morphology, diameter, size distribution and PS loaded amount) and photophysically studied (absorption capacity, fluorescence efficiency, and singlet oxygen production) in suspension. For the most promising PS-PEG-FA silica nanoplatforms, the biocompatibility in dark conditions and the phototoxicity under suitable irradiation wavelengths (blue, green, or red) at regulated light doses (10-15 J/cm2) were compared with PSs free in solution in HeLa cells in vitro.

The evolution towards Industry 4.0 is driving the need for innovative solutions in the area of network management, considering the complex, dynamic and heterogeneous nature of ICT supply chains. To this end, Intent-Based networking (IBN) which is already proven to evolve how network management is driven today, can be implemented as a solution to facilitate the management of large ICT supply chains. In this paper, we first present a comparison of the main architectural components of typical IBN systems and, then, we study the key engineering requirements when integrating IBN with ICT supply chain network systems while considering AI methods. We also propose a general architecture design that enables intent translation of ICT supply chain specifications into lower level policies, to finally show an example of how the access control is performed in a modelled ICT supply chain system.

In 2019, Chinese government implemented the first round of National Centralized Drug Procurement (NCDP) pilot (so-called "4+7" policy) in mainland China, achieved a prominent price reduction of 52% on average for 25 bidding winning products. Under cross-price elasticity theory, the price behavior of pharmaceutical enterprises for policy-related drugs might change. This study used drug purchasing data from the Centralized Drug Procurement Survey in Shenzhen 2019, and applied single-group Interruption Time Series (ITS) design to examine the impact of "4+7" policy on the drug price index (DPI) of policy-related drugs. The ITS analysis showed that the DPI of winning (-0.183 per month, p&lt;0.0001) and non-winning (-0.034 per month, p=0.046) products significantly decreased after the implementation of "4+7" policy. No significant difference was found for the immediate change of DPI for alternative drugs (p=0.537), while a significant decrease in change trend was detected in the post-"4+7" policy period (-0.003 per month, p=0.014). The DPI of the overall policy-related drugs significantly decreased (-0.261 per month, p&lt;0.0001) after "4+7" policy. These findings indicate that the price behavior of pharmaceutical enterprises changed under NCDP policy, while the price linkage effect is still limited. It is necessary to further expand the scope of centralized purchased drugs and strengthen the monitoring of related drugs regarding price change and consumption structure.

Estimating the economic risks of climate shocks and climate stressors on spatially heterogeneous cities over time remain highly challenging. The purpose of this paper is to present a practical methodology to assess the economic risks of climate change in developing cities to inform spatially sensitive municipal climate response strategies. Building on a capital-based framework (CBF), spatially disaggregated baseline and future scenario scores for economic wealth and its exposure to climate change are developed for six different classes of capital and across 77 major suburbs in Cape Town, South Africa. Capital-at-risk was calculated by combining relative exposure and capital scores across different scenarios and with population impacted plotted against the major suburbs and the city’s 8 main planning districts. The economic risk assessment presented here provides a generic approach to assist investment planning and the implementation of adaptation options through an enhanced understanding of relative levels of capital endowment vis-à-vis relative levels of exposure to climate-related hazards over time. An informed climate response strategy in spatially heterogeneous cities need to include spatially sensitive estimates on capital-at-risk and populations disproportionally impacted by climate exposure over time. The economic risk assessment approach presented here helps in advancing to such a goal.

Bacterial cellulose (BC) is receiving great attention due to its unique properties such as high purity, water retention capacity, high mechanical strength, and biocompatibility. However, the production of BC has been limited because of high cost and low productivity. In this light, the isolation of new BC producing bacteria and selection of high productive strains became a promising issue. Kombucha tea is a fermented beverage in which the bacteria fraction of the microbial community is composed mostly by strains belonging to the genus Komagataeibacter. In this study Kombucha tea production trials were performed starting from a previous batch, and bacterial isolation was conducted along cultivation time. From the whole microbial pool, 46 isolates were tested for their ability in producing BC. The obtained BC yield ranged from 0.59 g/L, for the isolate K2G36, to 23 g/L for K2G30 used as the reference strain. The genetic intraspecific diversity of the 46 isolates was investigated using two repetitive-sequence-based PCR typing methods, which are the enterobacterial repetitive intergenic consensus (ERIC) elements and the (GTG)5 sequences, respectively. The results obtained using two different approaches revealed the suitability of the fingerprints techniques, showing a discrimination power, calculated as D index, of 0.94 for (GTG)5 rep-PCR and 0.95 for ERIC rep-PCR. In order to improve the sensitivity of the applied method, a combined model from the two genotyping experiments was performed, allowing to discriminate among strains.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

Nature Based Solutions (NBS) are becoming increasingly important in both the EU and individual countries' political agendas, as a sustainable means to reduce the risk posed by hydrometeorological hazards. However, as the use of NBS is increasing, a number of barriers regarding their practical implementation also becomes apparent. A number of review studies have summarized and classified barriers, mainly in urban settings. PHUSICOS is a H2020 Innovation Action to demonstrate the use of NBS in rural and mountain landscapes. Large scale demonstrator case sites with several sub-projects are established in Italy, Norway and in the French and Spanish Pyrenees. The present paper describes the project's NBS measures, and their experienced barriers, some of which have resulted in full cancellation of the planned interventions. Many of the barriers experienced in rural settings have the same root causes as the ones described from urban areas, and the main barrier-creating mechanisms are institutional factors, resistance among stakeholders and technical and economic issues. The key element, however, is lack of knowledge about the ability of NBS to deliver a series of co-benefits in addition to their risk-reducing effects, and that long-term thinking is required to see the effect of many of these co-benefits.

Several studies suggest that COVID-19 may be accompanied by symptoms such as a dry cough, muscle aches, sore throat, and mild to moderate respiratory illness. The symptoms of this disease indicate the fact that COVID-19 causes noticeable negative effects on the lungs. Therefore, considering the health status of the lungs using X-rays and CT scans of the chest can significantly help diagnose COVID-19 infection. Due to the fact that most of the methods that have been proposed to COVID-19 diagnose deal with the lengthy testing time and also might give more false positive and false negative results, this paper aims to review and implement artificial intelligence (AI) image-based diagnosis methods in order to detect coronavirus infection with zero or near to zero false positives and false negatives rates. Besides the already existing AI image-based medical diagnosis method for the other well-known disease, this study aims on finding the most accurate COVID-19 detection method among AI methods such as machine learning (ML) and artificial neural network (ANN), ensemble learning (EL) methods.

COVID-19 has emerged as deadly pandemic worldwide with no vaccine or suitable antiviral drugs to prevent or cure the disease. Because of the time-consuming process to develop new vaccines or antiviral agents, there has been a growing interest in repurposing some existing drugs to combat SARS-CoV-2. Vitamin D is known to be protective against acute respiratory distress syndrome (ARDS), pneumonia and cytokine storm. Recently it has been used as a repurposed drug for the treatment of H5N1 virus-induced lung injury. Circumstantial evidences indicate that people with low level of vitamin D are more susceptible to SARS-CoV-2. Although, vitamin D was suggested to interfere with viral replication, its interaction with any SARS-CoV-2 protein is unexplored yet. Beside this, ivermectin, a well-known anti-parasitic agent, exhibits potent anti-viral activities in vitro against viruses such as HIV-1 and dengue. Very recently, ivermectin has been found to reduce viral load of SARS-CoV-2 in vitro. We have analyzed available structures of SARS-CoV-2 proteins to identify probable binding partner(s) of vitamin D and ivermectin through knowledge-based docking studies and figured out possible implication of their binding in SARS-CoV-2 infection. Our observations suggest that the non-structural protein nsp7 possesses a potential site to house 25-hydroxyvitamin D3 (VDY) or the active form of Vitamin D, calcitrol. Binding of vitamin D with nsp7 likely to hamper the formation of nsp7-nsp8 complex which is required to bind with RNA dependent RNA polymerase (RdRP), nsp12 for optimal function. On the other hand, potential binding site of ivermectin has been identified in the S2 subunit of trimeric spike(S) glycoprotein of SARS-CoV-2. We propose that deeply inserted mode of ivermectin binding at three inter-subunit junctions may restrict large scale conformational changes of S2 helices which is necessary for efficient fusion of viral and host membrane. Our study, therefore, opens up avenues for further investigations to consider vitamin D and ivermectin as potential drugs against SARS-CoV-2.