In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

The modeling of flood-induced bend scour near embankment toes can provide important information for river engineering, embankment safety warnings, and emergency action management. During the rainy seasons, short-term general scour and bend scour are the most common causes for the failure of reinforced concrete embankments in Taiwan. To gain a deeper understanding of the scouring process near levee foundations, this study proposed a straightforward and practical method for bend scour simulation. The proposed simulation method is subdivided into three stages: two-dimensional flow simulation, general scour estimation, and bend scour estimation. A new bend-scour computation equation is proposed and incorporated into a two-dimensional hydraulic finite-volume model for simulating the evolution of bend scour depth around embankment toes. The proposed method is applied to simulate the temporal evolution of bend scouring near the Shuideliaw Embankment on the Cho-Shui River in Taiwan, where serious failure occurred during the June 2012 monsoon. Field data were gathered using the numbered-brick technique at the Shuideliaw Embankment to demonstrate the accuracy of the proposed method. The results of the bend scour simulations compared reasonably well with field measurements, indicating close agreement in terms of water levels and bend scour depths near the Shuideliaw Embankment. The proposed method was found to quickly estimate the maximum short-term general scour and bend scour depths for further enhancement of the safety of the embankment toe.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

The traditional sequent peak algorithm (SPA) was used to assess the reservoir volume (VR) for comparison with deficit volume, DT, (subscript T representing the return period) obtained from the drought magnitude (DM) based method with draft level set at the mean annual flow on 15 rivers across Canada. At an annual scale, the SPA based estimates were found to be larger with an average of nearly 70% compared to DM based estimates. To ramp up DM based estimates to be in parity with SPA based values, the analysis was carried out through the counting and the analytical procedures involving only the annual SHI (standardized hydrological index, i.e. standardized values of annual flows) sequences. It was found that MA2 or MA3 (moving average of 2 or 3 consecutive values) of SHI sequences were required to match the counted values of DT to VR. Further, the inclusion of mean, as well as the variance of the drought intensity in the analytical procedure, with aforesaid smoothing led DT comparable to VR. The distinctive point in the DM based method is that no assumption is necessary such as the reservoir being full at the beginning of the analysis - as is the case with SPA.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Mangrove forests provide a wide range of goods and services that sustain communities around the world. This paper explores utilization patterns of extractable mangrove resources by communities within the proposed Kenya – Tanzania Transboundary Conservation Area (TBCA). Some 152 household surveys and 12 Nominal Group Technique discussions were carried out. At least 16 direct use products were reported to be extracted from the mangroves, with 90% of households found to use mangrove products. Changing patterns of mangrove use in the areas and accessibility point towards unsustainable utilization and promote illegal activities. Overharvesting of mangrove wood products was reported to be the major threat facing the forests. Patterns of mangrove use in the study site reveal a high level of mangrove-dependence by communities for their livelihood. There is a need to address the problems of open access through capacity building and awareness creation, development and implementation of harvest plans as well as introduction of alternative livelihood options to the communities in the area.

This study examined the accumulations and transfer of manganese into 11 wild plants from the mining soils of Gümüşköy, Turkey. The greatest silver resource in Turkey is found in the Gümüsköy mining area, which is situated roughly 25 kilometers to the west of Kütahya. ICP-MS was used to determine the Mn contents in soil and plant samples that were taken from the field. In the research area, the average Mn concentrations in the soil, roots, and shoots of wild plants were 1872, 1076, and 1048 ppm, respectively. Based on their ECS and ECR values, the plants were divided into three groups: the best plants, good plants, and candidate plants. While Glaucium flavum, Carduus nutans, Phlomis sp., Onosma sp., and Verbascum thapsus were selected as the best plants, Cynoglossum officinale, Anchusa arvensis were determined as good plants, and the others (Alyssum saxatile, Centaurea cyanus, Silene compacta, Isatis were determined as candidate plants. According to the current study, all of the best and good plants in the study region had a very high ability to remove Mn. As a result, these plants can be helpful in studies involving phytoremediation or remediation of Mn-polluted soil.

In the present work, a methodology for wind field reconstruction based on the Meteo Particle Model (MPM) from Numerical Weather Prediction (NWP) data is presented. The development of specific wind forecast services is a challenging research topic, in particular for what concerns the availability of accurate local weather forecasts in highly populated areas. Currently, even if NWP Limited Area Models (LAMs) are run at spatial resolution of about 1 km, this level of information is not sufficient for many applications, for example to support drone operation in urban contexts. The coupling of MPM with the NWP Limited Area Model COSMO has been implemented in such a way that the MPM reads the NWP output over a selected area and provides wind values in the generical point considered for the investigation. The numerical results obtained reveal a good behavior of the method in reproducing the general trend of wind speed, as confirmed also by the power spectra analysis. The MPM is able to step over the intrinsic limitations of the NWP model in terms of spatial and temporal resolution even if the MPM inherits the bias that inevitably affects the COSMO output.

Leptospirosis is an important zoonotic disease that is transmitted worldwide through infected small mammals such as rodents. In Malaysia, there is paucity of information on the animal reservoirs that are responsible for leptospirosis transmission, with only few studies focusing on leptospirosis risk in recreational areas. Therefore, in this study, we characterized the species composition and the prevalence of pathogenic Leptospira spp. in non-volant small mammals of Hutan Lipur Sekayu, Terengganu. We performed ten trapping sessions totaling 3,000 trapping efforts between September 2019 and October 2020. Kidney samples from captured individuals were extracted for the PCR detection of pathogenic Leptospira spp. Overall, we captured 45 individuals from 8 species (1.56% successful trapping effort), with 9 individuals testing positive for pathogenic Leptospira, that is 20% (n = 9/45) prevalence rate. Rattus tiomanicus (n = 22) was the most dominant captured species and was found to harbour the highest positive individual with pathogenic Leptospira (44.4%, n = 4/9). Despite the low successful trapping effort in this study, the result shows that the non-volant small mammals of Hutan Lipur Sekayu are capable of maintaining and transmitting pathogenic Leptospira, thus making this recreational area a potential infestation ground for leptospirosis.

The paper comes from the need to search for criteria useful for the valorization of heritage towns, located in rural and/or inland areas of Italy, now affected to depression and depopulation process. To this end, the authors point out how territorial identity can constitute the theoretical foundation to influence the development policies and, in particular, the tourism development for sustainability process It was therefore decided to interview a number of stakeholders who could contribute with their professionalism and expertise to identify possible paths and processes for the enhancement of these areas for tourism development. The methodology was based on be to be interviews with open questions, which allowed to identify a SWOT analysis, offering a guideline for a correct governance of these rural areas for their tourist enhancement, in terms of sustainability of development and tourist attractiveness. The study is an observatory that will monitor the implementation of sustainable tourism enhancement of the borghi, heritage town

The accurate calculation of real contact area between rough surfaces is a key issue in tribology. In this paper, based on the geometrical information of total contact area and the number of contact spots with respect to surface separation, a new method is proposed to determine the relation between real contact area and normal load. The contact of rough surfaces is treated as an accumulation of incremental multi-plateaus indentations with varying average contact radius. Comparisons with direct finite element calculations and some other theoretical predictions demonstrate the efficiency of this approach.

Due to a simple crane limited capacity; there is an urgent need to use high capacity cranes such as tower cranes. However, with regard to their high expense, we have to take into consideration selecting what type of cranes to be utilized which has been discussed by many researchers. In this research, a proposed technique was created to select the suitable type of crane and best place for crane erection, in addition to minimum radius for requested crane in order to minimize cost. To fulfill that target, a computer program is designed to numerate these problems, demonstrating an example explaining how to apply program and the result donated best place.

Recently, environmental degradation has become an international issue due to the extensive economic activities around the globe. This aspect demands the policymakers' and new researchers’ emphasis. Hence, the present article examines the impact of corporate social responsibilities (CSR) to community and environment on the environmental performance (ENP) of the manufacturing industry in China. The article also investigates the mediating role of green innovation and environmental strategy among CSR to community, CSR to environment and ENP of manufacturing industry in China. The article gets the primary data from the selected employees of the manufacturing industry using questionnaires. The article also tests the data's validity and reliability, and association among variables using smart-PLS. The outcomes indicated that CSR to environment has a positive association with ENP. The outcomes also revealed that green innovation and environmental strategy significantly mediate among CSR to community, CSR to environment and ENP. The article guides the policymakers in making policies related to improve ENP using CSR to environment and green innovation.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

We report on a 2D-gap surface plasmon metasurface based composed of a bottom metal layer, middle insulator layer, and top metal nanostructure of gold nanoblocks (nanoantennas). The proposed structure enables us to generate simultaneous multi plasmonic resonances and offers the possibility to tune them, within the near-infrared domain. The simplicity of the metasurface makes it promising for compact optical platforms based on reflection mode operation with potential application in multi-channel biosensors, second-harmonic generation, and multi-wavelength surface-enhanced spectroscopy among other interesting fields

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.

Crop phenotyping data collection is the basis for precision agriculture and smart decisionmaking applications. In this study, a dynamic slicing and reconstruction canopy volume (DR) algorithm is proposed to accurately estimate citrus canopy volume. The algorithm dynamically slices nearby slices based on their proportional area change and density difference, subsequently conducting AS reconstruction and volume calculation for each slice using an iterative mean point spacing as the α-value. Compared with six point cloud-based reconstruction algorithms, the DR approach achieved the best results in removing perforations and lacunae (0.84) and exhibited volumetric consistency (1.53) that closely aligned with the growth pattern of citrus trees. The DR algorithm effectively addresses the challenges of adapting the thickness and number of canopy point cloud slices to the shape and size of the canopy in the ASBS and CHBS algorithms, as well as overcoming inaccuracies and incompleteness in reconstructed canopy models caused by limitations in capturing detailed features using the PCH algorithm. It offers improved adaptive ability, finer volume computations, better noise reduction, and anomaly removal. In conclusion, we recommend selecting appropriate operating environments for each algorithm based on their principles, geometric properties, volumetric values, running time, and linear relationships with one another to guide orchard mechanization and intelligent operation.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

Background: Acute viral gastroenteritis remains a leading cause of health care cost globally, prompting the need for basic diagnostic strategies. Objectives: This study aims to assess the impact of viral gastroenteritis on hemogram and C-reactive protein. Methods: By conducting a retrospective study, three groups of children diagnosed with gastroenteritis (rotavirus positive, adenovirus positive and rota/adenovirus negative group) were compared in terms of hemogram parameters and C- reactive protein. Results: Among 756 children with gastroenteritis, 7.9% of patients were rotavirus positive and 6.5% of them were adenovirus positive. Our findings disclosed a statistically significant association between low lymphocyte (2.2 ± 1.45) and MPV value (7.38 ± 0.4 fL) with rotavirus gastroenteritis. Also, the analysis revealed a high neutrophil/lymphocyte ratio (2.8± 2.1) in rotavirus group. However, our study did not reveal any prominent laboratory marker that serves as a distinctive feature of adenovirus unlike rotavirus. Conclusions: In conclusion our research highlights the potential of decreased mean platelet volume and lymphopenia as diagnostic markers for rotavirus gastroenteritis.

The role of volume hydrogel holographic gratings as optical transducers in sensor devices for point-of-care applications is increasing due to their ability to be functionalized for achieving enhanced selectivity. The first step in the development of these transducers is the optimization of the holographic recording process. The optimization aims at achieving gratings with reproducible diffraction efficiency, which remains stable after reiterative washings, typically required when working with analytes of biological nature or several step tests. The recording process of volume phase transmission gratings within acrylamide/propargyl acrylate hydrogel layers reported in this work was successfully performed and the obtained diffraction gratings were optically characterized. Unslanted volume transmission gratings were recorded in the hydrogel layers and using the optimized conditions, diffraction efficiencies of up to 80% were achieved. Additionally, the recorded gratings demonstrated to be stable in water after multiple washings. The hydrogels, after functionalization with oligonucleotide probes yields specific hybridization response, recognizing the complementary strand as demonstrated by fluorescence. Analyte-sensitive hydrogel layers with holographic structures are a promising candidate for the next generation of in vitro diagnostic tests.

Physical exercise is the greatest stress on the cardiovascular system, not only in humans but also in all vertebrates. Consequently, the cardiovascular response cannot be thought of as having only one "anthropocentric" interpretation. The modulation of cardiac output (Q) in response to exercise in the five major groups of vertebrates exhibits considerable variability. Moreover, the response of the heart rate (HR) and the stroke volume (SV), the fundamental factors that cause the rise in Q, is also highly variable. The difference in the range of HR is difficult to determine in many vertebrates, both at rest and at maximal effort. Additionally, the increase in SV varies among vertebrates. For example, while rainbow trout and leopards increase their SV by increasing end diastolic volume (EDV), humans do so at the expense of both increasing EDV and reducing end systolic volume (ESV). The variation in arterial pressure that arises during exercise varies notably among vertebrates, such as amphibians, whose blood pressure values do not increase as significantly as in mammals. Such differences in cardiovascular response among vertebrates may be linked to their habitat or living environment. This review aims to analyze the cardiovascular response of vertebrates to physical exercise as the most common stressor.

Background. To prospectively evaluate the reliability of a portable optical scanner compared to the water displacement technique for volumetric measurements of the foot and ankle, and to compare the acquisition time associated with these two methods. Methods. Foot volume was measured in 29 healthy volunteers (58 feet, 24 female/5 male) by a 3D scanner (UPOD-S 3D Laser Full-Foot Scanner ®) and by water-displacement volumetry. Measurements were performed on both feet, up to a height of 10 cm above the ground. The acquisition time for each method was evaluated. Kolmogorov-Smirnov test, Lin's Concordance Correlation Coefficient, and a Student’s t-test were performed. Results: Mean foot volume was 869.7+/-165.1cm3 (3D scanner) versus 867.9+/-155.4cm3 (water-displacement volumetry) (p <10-5). Concordance of measurements was 0.93, indicative of a high correlation between the two techniques. Volumes were 47.8 cm3 lower when using the 3D scanner versus water volumetry. After statistically correcting this underestimation, the concordance was improved (0.98, residual bias = -0.03 +/- 35.1 cm3). Mean examination time was 4.2 +/-1.7 min (3D optical scanner) versus 11.1 +/-2.9 min (water volumeter) (p<10-4). Conclusion: Ankle/foot volumetric measurements performed using this portable 3D scanner are reliable and fast, and can be used in clinical practice and research.

Previous studies have mostly examined how sustainable cities try to promote non-motorized travel by creating a walking-friendly environment. Such existing studies provide little research that identifies how the built environment affects pedestrian volume in high-density areas. This paper presents a methodology that combines person correlation analysis, stepwise regression, and principal component analysis for exploring the internal correlation and potential impact of built environment variables. To study this relationship, cross-sectional data in the Melbourne central business district were selected. Pearson’s correlation coefficient confirmed that visible green index and intersection density were not correlated to pedestrian volume. The results from stepwise regression showed that land-use mix degree, public transit stop density, and employment density could be associated with pedestrian volume. Moreover, two principal components were extracted by factor analysis. The result of the first component yielded an internal correlation where land-use and amenities components were positively associated with the pedestrian volume. Component 2 presents parking facilities density, which negatively relates to the pedestrian volume. Based on the results, existing street problems and policy recommendations were put forward to suggest diversifying community service within walking distance, improving the service level of the public transit system, and restricting on-street parking in Melbourne.

The article contains the results of experimental studies for a multi-opening orifice with substitute constriction factor of β = 0.5 (m = 0.25), mounted in a DN50 hydraulic measuring flume. Flow measurements were taken for a progressing turbulent flow within Reynolds numbers (Re = 4700...19500). Based on experimental data, flow characteristics as well as discharge coefficient C characteristics were determined. Relative expanded uncertainty of determining a discharge coefficient C was estimated within the changes of volume flow qv from 0.35 dm3/s to 0.68 dm3/s. The value does not exceed 1.25% within the changes of Reynolds numbers 9800 ≤ Re ≤ 19500.

Titanium’s accelerating usage in global markets is attributable to its distinctive combination of physical and metallurgical properties. The key to best utilizing titanium is to exploit these characteristics, especially as they complement one another in a given application, rather than to just directly substitute titanium for another metal. Titanium alloy are extensively used in aerospace applications such as components in aero-engines and space shuttles, mainly due to their superior strength to weight ratio. For these demanding applications functionality and reliability of components are of great importance. To increase flight safety, higher sensitivity inspections are sought for rotating parts. Increased sensitivity can be applied at the billet stage, the forging stage, or both. Inspection of the forging geometry affords the opportunity to apply the highest sensitivity due to the shorter material paths when compared to those required for billet inspections. Forging inspection is typically performed for titanium (Ti) rotating parts with immersion inspection and fixed-focus, single-element transducers. Increased gain is required with depth because the ultrasonic beam attenuates with distance and diverges beyond the focus position that is placed near the surface. The higher gain that is applied with depth has the effect of increasing the UT noise with depth. The relationships between the UT noise, selection of the examination technique and the smallest detectable defect are presented in this material.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

In this study, a parameter of volume stability was proposed for the first time to design polymorph zirconia ceramics used for special components. A series of heterogeneous polymorph zirconia ceramics with various amounts of monoclinic (M) phase were fabricated by two-step sintering. Samples with about 27%, 31%, and 51% M phase content were selected to study the properties. The thermal shock durability was found to be associated with thermal expansion behavior and noncritical micro cracks, which both based on M phase initial content. In good agreement with experimental results, the correlation of normalized K versus M phase initial content was established. It could provide a repeatable reference to prepare special zirconia components without loss of density.

Hydraulic fracturing in shale gas reservoirs has usually resulted in complex fracture network. The results of micro-seismic monitoring showed that the nature and degree of fracture complexity must be clearly understood to optimize stimulation design and completion strategy. This is often called stimulated reservoir volume (SRV). In the oil & gas industry, stimulated reservoir volume has made the shale gas exploitation and development so successful, so it is a main technique in shale gas development. The successful exploitation and development of shale gas reservoir has mainly relied on some combined technologies such as horizontal drilling, multi-stage completions, innovative fracturing, and fracture mapping to engineer economic completions. Hydraulic fracturing with large volumes of proppant and fracturing fluids will not only create high conductivity primary fractures but also stimulate adjacent natural fractures. Fracture network forming around every hydraulic fracture yields a stimulated reservoir volume. A model of horizontal wells which was based on a shale gas reservoir after volume fracturing in China was established to analyze the effect of related parameters on the production of multi-fractured horizontal wells in this paper. The adsorbed gas in the shale gas reservoir is simulated by dissolved gas in the immobile oil. The key to simulate SRV is to accurately represent the hydraulic fractures and the induced complex natural fracture system. However, current numerical simulation methods, such as dual porosity modeling, discrete modeling, have the following limitations: 1) time-consuming to set up hydraulic and natural fracture system; 2) large computation time required. In this paper, the shape of the stimulated formation is described by an expanding ellipsoid. Simplified stimulated zones with higher permeability were used to model the hydraulic fracture and the induced complex natural fracture system. In other words, each primary fracture has an enhanced zone, namely SRV zone. This method saves much developing fine-grid time and computing time. Compared with the simulation results of fine-grid reference model, it has shown that this simplified model greatly decreases simulation time and provides accurate results. In order to analyze the impacts of related parameters on production, a series of simulation scenarios and corresponding production performance were designed. Optimal design and analyses of fracturing parameters and the formation parameters have been calculated in this model. Simulation results showed that the number of primary fractures, half length, SRV half-width and drop-down have great effects on the post-fracturing production. Formation anisotropies also control the production performance while the conductivity of the primary fractures and SRV permeability do not have much impact on production performance. The complexity of stimulated reservoir volume has strong effect on gas well productivity. Fracture number mainly affects the early time production performance. The increase of SRV width cannot enlarge the drainage area of the multi-fractured horizontal wells, but it can improve the recovery in its own drainage region. Permeability anisotropies have much effect on production rate, especially the late time production rate. The results prove that horizontal well with volume fracturing plays an irreplaceable role in the development of ultra-low permeability shale gas reservoir.

Product introductions play a pivotal role in the success and competitiveness of manufacturing, particularly in the context of new product development. Low-volume manufacturing companies exhibit distinct characteristics that significantly influence the product introduction process. Notably, the quality of information exchange between product design and production interfaces becomes paramount in this high-mix and low-volume industry. Consequently, there exists a pressing need to explore various methods for adapting and customizing management mechanisms and strategies to align with the unique requirements and characteristics of low-volume manufacturing and its associated product introduction processes. While the need for this knowledge is critical in the context of low-volume manufacturing, a majority of existing studies predominantly focus on the management aspects within high-volume manufacturing. Therefore, the primary aim of this study is to investigate the customization of product introduction management strategies to enhance the quality of information content within the realm of low-volume manufacturing. Drawing upon a longitudinal analysis of new product introductions within a low-volume manufacturing company, this study narratively elucidates how the examined company implemented product introduction management strategies to facilitate the enhancement of information content quality during the product introduction phase. The study presents its findings on management strategies across three key stages: pre-implementation, post-implementation, and subsequent modification and refinement of strategies following the initial round of implementation. By shedding light on these strategies, this study offers a comprehensive understanding of management approaches in the context of low-volume product introduction. As a result, it makes a valuable contribution to the discourse on information management and interface management in the high-mix, low-volume manufacturing literature.

Studying the interaction between the upper ocean and the typhoons is crucial to improve our understanding of heat and momentum exchange between the ocean and the atmosphere. In recent years, the upper ocean responses to typhoons have received considerable attention. The sea surface cooling (SSC) process has been repeatedly discussed. In the present work, case studies were examined on five strong and super typhoons that occurred in 2016—LionRock, 1610; Meranti, 1614; Malakas, 1616; Megi, 1617; and Chaba 1618—to search for more evidence and new features of typhoon’s impact on the sea surface environment. The typhoon monitoring data from the Central Meteorological Observatory, the sea surface temperature (SST) data from satellite microwave and infrared remote sensing, and the sea surface height anomaly (SSHA) data from satellite altimeters were used to analyze in detail: the SSC features caused by typhoons, the relationship between the SSC and the typhoon travelling speed, and the variations in cold and warm eddies during typhoon passage. Results showed that: (1) SSC generally occurred during typhoon passage and the degree of SSC was always determined by the strength and the travelling speed of the typhoon, as well as the initial SST. (2) One day before or on the day of typhoon passage, the SSHA slightly increased due to low surface pressure. After the typhoon passed, the SSHA obviously decreased along with the SSC. The pre-existing positive SSHAs, which always represent warm eddies, decreased or disappeared during typhoon passage, whereas negative SSHAs or cold eddies were enhanced. (3) New cold eddies were generated, especially at the turning points of the typhoon path. The presence of warm eddies is suggested to have a strengthening effect on the typhoons.

Protected and conserved areas are a key area-based strategy to address the biodiversity and climate change crises. Fundamental to understand their performance over time are indicators. The Digital Observatory for Protected Areas (DOPA) was born in 2013 as a set of open access web services and applications to be used to assess, monitor, and report on protected and conserved areas. For over a decade it has delivered over 50 indicators to support policy processes, national and regional governments, and practitioners. DOPA has also developed a versatile and efficient back-end approach that is widely applicable in other area-based conservation contexts. Here, we describe the methods and workflows behind DOPA´s back end and provide examples of policy relevant questions it can answer. We discuss key advantages and limitations of this systematic and replicable approach and explore the use of this back-end architecture to inform progress in area-based conservation targets for the following decades. This approach, embedded in multiple services provided by the Knowledge Centre for Biodiversity of the European Commission (KCBD), can also support the implementation and monitoring of area-based targets of the Kunming Montreal Global Biodiversity Framework at international, regional, and national levels.

This case report utilized the primary data gathered from the extension program of the LORMA College of Medical Laboratory Science at the institution’s adopted locale. Arosip is a secluded, difficult-to-reach mountainous barangay in the municipality of Bacnotan, in the province of La Union, Philippines. The study subjects were forty-one (41) kindergarten to grade three students of Arosip Elementary School. Modified Kato-Katz technique was performed to the submitted stool samples. Among 41 participants, nine were screened positive for the helminthic ova of Ascaris lumbricoides, and Trichuris trichiura – yielding a total of 21.95% prevalence rate. Among those 9 participants, 6 (66.67%) were positive for Ascaris lumbricoides ova, and 3 (33.33%) were co-infected with both Ascaris lumbricoides and Trichuris trichiura ova. The findings were relayed and reported to the local government unit. The team recommends for a more comprehensive screening and monitoring of STH cases in the locale, a continuous stewardship of health programs including mass-deworming for the school children and awareness campaigns, and provision of health resources. Ultimately, interagency collaboration between the Department of Health, Department Education, and Local Government Unit remains highly warranted to satisfy the health inequities experienced by this disadvantaged remote community.

Rural areas are not only faced with the problems of rural depopulation but also with the problem of water supply and water quality which is a basic necessity of life. In light of this, this paper assesses the rural water supply situation and the bacteriological quality of different water sources in the Obokun Local Government Area of Osun State, Nigeria. The safety of the water sources for human consumption and possible occurrence of the water borne diseases in the study area were determined. The study employed descriptive and analytical methods of data analysis to achieve the objectives of the inquiry. Findings showed that the study area suffered from inadequate water supply and poor locations of the sources of water: The study also revealed that the microbiological quality of the water sources used was unsafe, poor and not acceptable for human consumption. In addition, many man- days-hours were wasted in search of water. It is therefore recommended that the government should make the rural water supply and the maintenance of water quality a priority in its policy formulation.

Understanding the contribution of protected areas to pollinating insect conservation is crucial, especially in Haiti because of intense deforestation and environmental degradation. We compared pollinating insect assemblage composition and abundance in two protected areas: the suburban Wynne Farm Ecological Reserve (WFER) and the Urban National Park of Martissant (UNPM). Both sites encompass forest patches, agroforestry, and agricultural crops. Using colored pan-traps, we collected 3722 insects from six Orders, with 68.2% identified to family level due to taxonomic limitations. WFER exhibited significantly higher insect abundance than UNPM, though habitat differences varied between sites. Site, habitat, and their interaction significantly influenced insect composition. Among 118 identified families, only 30.51% were shared between sites. Our data suggest combined protection offers broader and more even insect diversity. We discovered patrimonial lepidopteran and hymenopteran species previously unrecorded in Haiti, emphasizing the importance of protected areas and the need for enhanced entomological expertise.

Coal mining has caused a significant loss of nitrogen content of soil in mining areas. This article studies the effects of organic fertilizer, inorganic fertilizer, and combined application of Pseudomonas fluorescens with the ability of nitrogen fixation on soil nitrogen accumulation and composition in the reclamation area of Tunlan Coal Mine from 2016 to 2022 under the condition of equal nitrogen application, providing scientific basis for microbial fertilization and rapid increase of nitrogen content in the reclaimed soil of mining areas. The results showed that as the reclamation time increased, the nitrogen content and its composition structure of the soil treated with fertilization rapidly evolved towards normal farmland soil. The soil nitrogen content increased the fastest in the treatment of Pseudomonas fluorescens + organic fertilizer (MB), compared with inorganic fertilizer (CF), organic fertilizer (M), and Pseudomonas fluorescens + inorganic fertilizer (CFB) treatments, the treatment of Pseudomonas fluorescens + organic fertilizer (MB) can bring the total nitrogen (TN) content of the soil to normal farmland soil levels 1-3 years earlier. The comprehensive scores of Pseudomonas fluorescens + organic fertilizer (MB) and Pseudomonas fluorescens + inorganic fertilizer (CFB) on the two principal components were increased 1.58 and 0.79 than those of organic fertilizer (M) and inorganic fertilizer (CF) treatments, respectively. This further indicates that the combination of Pseudomonas fluorescens and organic fertilizer has a better effect on improving soil nitrogen accumulation than the combination of Pseudomonas fluorescens and inorganic fertilizer. At the same time, the application of Pseudomonas fluorescens will increase the content of unknown nitrogen (UN) in acid-hydrolysable nitrogen (AHN), and decrease the content of amino acid nitrogen (AAN) and ammonia nitrogen (AN), relatively. However, there was no significant effect on the content of ammonium nitrogen (NH4+-N) and nitrate nitrogen (NO3--N) in soil inorganic nitrogen (SMN). When combined with inorganic fertilizer, the contribution of soil mineralized nitrogen (SMN) to total nitrogen (TN) increased by 14.78%, while when combined with organic fertilizer, the contribution of acid-hydrolysable nitrogen (AHN) to total nitrogen (TN) increased by 44.77%. In summary, the use of Pseudomonas fluorescens is beneficial for nitrogen recovery in the reclaimed soil of coal mining areas. The optimal fertilization method under the experimental conditions is the combination of Pseudomonas fluorescens and organic fertilizer.

This paper evaluated the quality and suitability of surface water in the Vaalharts area, South Africa, for human consumption, drinking, and irrigation purposes. Water quality constituents include water pH, EC, TDS, HCO3-, Cl-, SO4, Mg, Ca, k, Na, NO3, F, Fe, PO4, As, Al, Mn, Cr, Cu, Zn, B, Cd, Hg, Pb, N, Sb, Se, and the biological parameter included E. coli along surface waters as well as canals and dams. Sodium Adsorption Ratio, Sodium Percentage, Permeability Index, Residual Sodium Carbonate, Kelley’s Ratio, Magnesium Hazard, and Potential salinity irrigation water parameters indicated that the majority of the water samples are suitable for irrigation. The water quality index values showed that the majority of the samples are unsuitable for drinking but suitable for irrigation and industrial uses. E. coli in the surface water samples in the study area show unsafe water quality with high and very high risk for human health. Based on the classifying criterion of the Heavy Metal Pollution Index and Heavy Metal Evaluation Index, all the water samples are above the critical limit, therefore, unsuitable for human consumption. The carcinogenic risk (CR) concentrations of As, Cr and Cd were above the target risk.

Abstract Natural disasters such as earthquakes have affected urban historical centers severely. Considering the limitations of the existing methods in conservation and preservation of these sensitive areas, and recent advances in technological devices and techniques such as GIS and 3D printers, this article aims to propose a new methodology utilizing available knowledge and resources. The authors of the present research propose an innovative, technological, and highly accurate method to assess the seismic vulnerability of historical contextures rectifying the existing obstacles and limitations. Through this methodology, the level of trial and error is substantially reduced and the output is stronger, more optimized and more conservative as compared with commonly used methods. Using high tech principles and theoretical foundations (i.e. sustainability principles) this method achieves updated analyses, practical plans, and economic optimization.

Cardiovascular diseases (CVD´s) continue as the primary cause of death worldwide. During the past couple of years, and with the surge of the COVID-19 pandemic, deaths linked to CVD´s were -slightly overshadowed by those deaths related to COVID-19, albeit during the highest peaks of the pandemic. The present study derived form understanding the correlation between both diseases, from the standpoint of patients already diagnosed with CVD´s (n = 41883) and what comorbidities had the highest influence on overall patient death (n = 3637). Obesity, hypertension, and diabetes are all linked to worsening the outcome of COVID-19 positive patients, hence they were considered when looking at the overview of all CVD positive patients. Our finding showed that 1697 deaths were related to diabetes (p < 0.001), 987 deaths were related to obesity (p < 0.001), and lastly 2499 deaths were attributed to hypertension (p < 0.001) individually. Using logistic regression modeling, we found diabetes (OR: 1.744, p < 0.001) and hypertension (OR: 2.179, p < 0.001) had a high impact on patient deaths. Hence, having a CVD diagnosis, with hypertension and/or diabetes seems to increase the likely-hood of complication leading to death in COVID-19 positive patients.

The latest EU regulation on geographical indications (EU Regulation No. 1151/2012) has intro-duced a set of new tools for the protection and enhancement of food products in rural areas, under the group name of optional quality term (OQT). The Commission Delegated EU Regulation, No. 665/2014, regulated the conditions for the use of the optional quality term «mountain product» (MP), to support the implementation of a mountain value chain. This new tool is aimed at pro-moting local development, maintaining the economic activities in mountain areas and redistrib-uting wealth, whilst, at the same time, promoting the territory. Pecorino and goat cheeses are typ-ical Italian cheeses made usually with whole raw ewe's or raw goat's milk, without starter cul-ture addition. In an attempt to characterize these productions, the aim of this study was to inves-tigate the evolution of enterococci during the production and ripening of Pecorino cheese made in three different farms, located in Umbria, Italy in areas facing natural or other specific constraints as stipulated by Regulation 1305/2013 on support for rural development by the European Agri-cultural Fund for Rural Development (EAFRD). Enterococci are enteric organisms which are commonly isolated from ewe and goat's milk production in Umbria, Italy. Counts of enterococci in raw milk ranged from 1.75 for ovine milk to 3.62 for ewe milk and a marked reduction was observed after thermization especially in ovine milk. Out of 100 isolates, 69 were E. faecium, 23 E. durans, 8 E. faecalis and 2 E. casseliflavus and the distribution of species between farms and be-tween samples showed a prevalence of E. faecium in ovine farms and E. durans in ewes farms, with an equal distribution between samples. High percentages of susceptible isolates were found for amoxicillin/clavulanic acid, ampicillin, chloramphenicol, sulphamethoxazole, sulphameth-oxazole/trimethoprim, ticarcillin, vancomycin. A high prevalence of resistant strains (> 30%) was observed for amikacin, ciprofloxacin, ceftriaxone, kanamycin, tetracycline. A comparison of this results with those of previous works on similar dairy products revealed high levels of resistance to antimicrobials which needs to be addressed.

Abstract: Cancer survivors are at an increased risk for cardiovascular disease (CVD). However, the association between particulate matter (PM) and CVD risk among cancer survivors (alive >5 years since diagnosis) is unclear. We investigated the risk of CVD among 40,899 cancer survivors within the Korean National Health Insurance Service database. Exposure to PM was determined by assessing yearly average PM levels obtained from the Air Korea database from 2008 to 2011. PMs with sizes <2.5 (PM2.5), <10 (PM10), or 2.5-10 (PM2.5-10) μm in diameter were compared, with each PM level exposure further divided into quintiles. Patients were followed up from January 2012 to date of CVD event, death, or December 2017, whichever came earliest. Adjusted hazard ratios (aHRs) and 95% confidence intervals (CIs) for CVD were calculated using Cox proportional hazards regression by PM exposure levels. Compared with cancer survivors in the lowest quintile of PM2.5 exposure, those within the highest quintile had a greater risk for CVD (aHR 1.31, 95% CI 1.07-1.59). Conversely, increasing PM10 and PM2.5-10 levels were not associated with increased CVD risk (p for trend 0.078 and 0.361, respectively). Cancer survivors who reduce PM2.5 exposure may reduce their risk of developing CVD.

We propose a new estimator for creating expansion factors for survey plots in the USDA Forest Inventory and Analysis program. This is a regularized version of the raking estimator widely used in sample surveys. The regularized raking method differs from other predictive modeling methods for integrating survey and ancillary data in that it produces a single set of expansion factors that can have general purpose use to produce small area estimates and wall-to-wall maps of any plot characteristic. This method also differs from other more widely used survey techniques, such of GREG estimation, in that it is guaranteed to produce positive expansion factors. We extend the previous method here to include cross-validation, and provide a comparison to expansion factors between the regularized raking and ridge GREG survey calibration.

Water resources management is one of the most important challenges worldwide because water represents a vital resource for sustaining life and environment. In the aim of sustainable groundwater management, the identification of aquifer recharge areas is a useful tool for water resources protection. In a well-developed karst aquifer, environmental isotopes provide support for identifying aquifer recharge areas, residence time and interconnections between aquifer systems. This study deals the use of environmental isotopes to identify the main recharge area of a karst aquifer in the Upper Valley of Aniene River (Central Italy). The analysis of 18O/16O and 2H/H values and their spatial distribution in the aquifer, make it possible to trace back groundwater recharge areas based on average isotope elevations. The Inverse Hydrogeological Balance Method was used to validate spring recharge elevations obtained by the use of stable isotopes. Areas impacted by direct and rapid rainfall recharge into the study area were delineated, showing groundwater flowpaths from the boundaries to the core of the aquifer. The results of this study demonstrate the contribution that spatial and temporal isotope changes can provide to the identification of groundwater flowpaths in a karst basin, taking into account the hydrogeological setting

The attributes of electroplating as a low-cost, simple, scalable and manufacturable semiconductor deposition technique for the fabrication of large-area and nanotechnology-based device applications are discussed. These strengths of electrodeposition are buttressed experimentally using techniques such as X-ray diffraction, Ultraviolet-visible spectroscopy, Scanning electron microscopy, Atomic force microscopy, Energy-dispersive X-ray spectroscopy and photoelectrochemical cell studies. Based on the structural, morphological, compositional optical, and electronic properties evaluated results, it is evident that electroplating possesses the capabilities of producing high-quality semiconductors usable in producing excellent devices. In this paper, we will describe the progress of electroplating technique mainly for the deposition of semiconductor thin film materials, their treatment processes and fabrication of solar cells.

Background: Coronary artery disease (CAD) remains a significant global health concern, being one of the most important contributors to morbidity and mortality worldwide. Accurate assessment of coronary lesions is crucial for guiding appropriate interventions and optimizing patient outcomes. Patients with acute myocardial infarction represent a population which is rarely selected in studies of intracoronary hemodynamics. Fractional Flow Reserve (FFR) has emerged as a valuable physiological index for evaluating the functional significance of coronary lesions, although the data of intravascular hemodynamic evaluation in patients with acute myocardial infarction is scarce [1-3]. In recent years, advancements in intravascular imaging techniques, such as Optical Coherence Tomography (OCT), have provided detailed insights into coronary anatomy both in acute or elective settings. [4-7]. Methods: This article aims to explore the correlation between different non-culprit vessel OCT-parameters and FFR value in the patients with recent acute myocardial infarction. The study included 114 patients with acute myocardial infarction (ST elevation myocardial infarction and non ST elevation myocardial infarction)for whom primary PCI (percutaneous coronary intervention) was performed for the culprit lesion. The non-culprit vessels with intermediate coronary stenoses (157 lesions) were evaluated in a staged procedure (during the index hospitalization) with OCT, FFR and revascularization was performed accordingly. Minimal luminal area (MLA) and percent luminal area stenosis (PSA) were analyzed in relation with the FFR value. Results: There is good correlation between OCT-derived parameters and FFR values in patients with recent acute myocardial infarction. Minimal luminal area (MLA) and percent luminal stenosis area (PSA) were independent predictors of FFR< 0,80 in multivariate logistic regression analysis. A value of 2,08 mm2 for the MLA and 76,85 % for the PSA have proved to be the best cut-offs for predicting a FFR< 0,80. Conclusions: OCT parameters are valuable additional tools in current angiographic practice, including patients with acute myocardial infarction, with the ability to bring numerous direct imagistic and indirect hemodynamic information.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

Amebiasis is a disease caused by the unicellular parasite Entamoeba histolytica. In most cases, the infection is asymptomatic but when symptomatic, the infection can cause dysentery and invasive extraintestinal complications. In the gut, E.histolytica feeds on bacteria. Increasing evidences support the role of the gut microbiota in the development of the disease. In this review we will discuss the consequences of E.histolytica infection on the gut microbiota. We will also discuss new evidences about the role of the gut microbiota in regulating the resistance of the parasite to oxi-dative stress and its virulence.

Accurate prostate volume estimation is crucial for effective prostate disease management. Ultrasound (US) imaging, particularly transrectal ultrasound, offers a cost-effective and rapid assessment. However, US images often suffer from artifacts and poor contrast, making prostate volume estimation challenging. This review explores recent advancements in deep learning (DL) techniques for automatic prostate segmentation in US images as a primary step for prostate volume estimation. We examine various DL architectures, including traditional U-Net modifications and innovative designs incorporating residual connections, multi-directional image data, and attention mechanisms. Additionally, we discuss pre-processing methods to enhance image quality, the integration of shape information, and strategies to improve the consistency and robustness of DL models. The effectiveness of these techniques is evaluated through metrics such as Dice Similarity Coefficient, Jaccard Index, and Hausdorff Distance. The review highlights the potential of DL in improving prostate volume estimation accuracy and reducing clinical workload, while also identifying areas for future research to enhance model performance and generalizability.

BACKGROUND: It has been shown that obesity and higher body mass index (BMI) are associated with higher recurrence rate of atrial fibrillation (AF) after successful catheter ablation (CA). The same has been proven for left atrial volume index (LAVI). It has also been shown that there is a correlation between LAVI and BMI. However, whether LAVI prognostic impact on AF recurrence is BMI independent, remains unclear. METHODS: We prospectively included 62 patients with paroxysmal AF who were referred to our institution for CA. All patients underwent radiofrequency CA with standard pulmonary veins isolation. Transthoracic 2-D echocardiography was performed one day after CA to obtain standard measures of cardiac function and morphology. Recurrence was defined as documented AF within 6 months of follow-up period. Patients were also instructed to visit outpatient clinic earlier in case of symptoms suggesting AF recurrence. RESULTS: We observed AF recurrence in 27% of patients after 6 months. The mean BMI in our cohort was 29.65 ± 5.08 kg/cm2 and the mean LAVI was 38.04 ±11.38 ml/m2. We further divided patients into 2 groups according to BMI. Even though LAVI was similar in both groups, we found it to be significant predictor of AF recurrence only in obese patients (BMI ≥ 30), but not in the non-obese group (BMI < 30). There was also no significant difference in AF recurrence between both cohorts. The significance of LAVI as AF recurrence predictor in obesity group was also confirmed in multivariate model. CONCLUSION: According to our results LAVI tends to be significant predictor of AF recurrence after successful catheter ablation in obese patients, but not in normal-weight and overweight patients. This would suggest different mechanisms of AF in non-obese patients in comparison to the obese. Further studies are needed in this regard.

The volume of fluid (VOF) method is a popular technique for the direct numerical simulations of flows involving immiscible fluids. A discrete volume fraction field evolving in time represents the interface, in particular, to compute its geometric properties. The height function method (HF) is based on the volume fraction field, and its estimate of the interface curvature converges with second-order accuracy with grid refinement. Data-driven methods have been recently proposed as an alternative to computing the curvature, with particular consideration for a well-balanced input data set generation and symmetry preservation. In the present work, a two-layer feed-forward neural network is trained on an input data set generated from the height function data instead of the volume fraction field. The symmetries for rotations, reflections, and the anti-symmetry for the phase swapping have been considered to reduce the number of input parameters. The neural network, establishing a correlation between curvature and height function values, can efficiently predict the local interface curvature. We compare the trained neural network to the standard Height Function method to assess its performance and robustness.

A novel compressible real gas 1D finite volume thermofluid network modelling methodology is proposed that can be applied in the analysis of supercritical CO₂ (sCO2) power cycles. It is applied to simulate centrifugal compressor performance via a mean line approach that directly solves the mass, energy, and momentum balance equations for the discretized flow channels within the machine along with the associated loss models, component characteristics, and applicable compressible real gas equation of state. This can be integrated seamlessly with the rest of the power cycle components like pipes, valves, heat exchangers, etc., thereby eliminating the need for static performance maps and the associated difficulties to ensure similarity over the whole range of operation. This direct simulation of the internal flows also makes it possible to do integrated cycle design optimization that includes the geometry of the compressors, and to simulate fast transients for dynamic analysis. The methodology was applied to simulate well-documented air and sCO2 centrifugal compressors and compared the generated results with that of conventional thermofluid network incompressible and compressible ideal gas approaches. The results indicate that the proposed compressible real gas approach can capture the stagnation pressure changes and isentropic efficiencies with good accuracy for both cases over the whole range of mass flow rates and shaft rotational speeds. In contrast, the conventional thermofluid network incompressible and compressible ideal gas approaches are only applicable in selected regions of the fluid property regime and suffer from discretization errors and inappropriate treatment of the relationship between stagnation and static pressures. Furthermore, comparative analyses between the newly proposed approach and the traditional mechanical energy balance method are performed, showing that the latter approach needs to be discretized more finely through the compression process to correctly capture the polytropic compression path shape, whereas the former more accurately captures the stagnation pressure changes through the analyzed compressors with only a single increment per compressor component.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

Background: The target volume for post-mastectomy radiation therapy (PMRT) in breast cancer patients with reconstruction has been a subject of debate. This study aimed to assess the radiation dose distribution and treatment outcomes associated with different chest wall (CW) delineation according to ESTRO ACROP guideline for patients underwent implant-based reconstruction. Methods: We conducted a retrospective review of breast cancer patients who underwent mastectomy followed by two-stage implant-based breast reconstruction and adjuvant radiation therapy (RT) between 2007 and 2022. The expanders/implants were positioned retropectorally. The chest wall target volumes were categorized into two groups: the prepectoral group, which excluded the deep lymphatic plexus, and the whole expander group. Results: The study included 26 patients, 15 in prepectoral group and 11 in whole expander group. No significant differences were observed in normal organs exposure between the two groups. There was a trend toward a lower ipsilateral lung mean dose in the prepectoral group (10.2 vs. 11.1 Gy, p=0.06). Both groups exhibited limited instances of reconstruction failure and local recurrence. Conclusions: For patients undergoing two-stage expander-implant retropectoral breast reconstruction and PMRT, our data have provided comparable outcomes and normal organs exposure for those omitting the deep lymphatic plexus.

Development of non-conventional hybrids (NCHs) responds to the demand for the Elotes Occidentales 'EO' race for production of pozole. The effect of: crop cycle (2019, 2020 and 2021) on physical characteristics, flowered grain quality and phytochemical content of two HNC (Pz1 and Pz2) of pozolero maize, as well as the effect of the presence or absence of pedicel, type of pollination (open and controlled, 2019), and progenitor lines (female and male, 2020) on flowered grain quality and content of phytochemical compounds were evaluated. Size, hardness, color, total phenols and anthocyanins in unprocessed grain were determined, and yield, volume and puncture strength in flowered grain. Results were analyzed with a factorial arrangement in a completely randomized design. There were significant differences (p≤0.05) in most of the variables studied by effect of crop cycle and genotype. NCHs had large grains (40 g 100 grains-1), soft endosperm (IF&gt; 60), pink-purple color, and phenol and anthocyanin contents similar to those reported for the 'EO' race. The presence or absence of the pedicel did not affect flowered grain quality. Controlled pollination favored anthocyanin synthesis. The anthocyanin content of NCHs was determined by the female line. Thermal processing reduced anthocyanins by 60%; however, they leached into the flowering broth, so that the pozole made from NCHs improves the nutraceutical value of the pozole, relative to that of pozole made with Cacahuacintle maize.

Syntactic foam has proven to be a good material with a strong structural strength. Understanding filler particle size variation is important in composite material formation especially in syntactic foam because of their numerous applications such as aerospace, marine and structural purposes. In this present work, the effects of particle variation in different sizes (20-24µm, 25-44µm, 45-49µm, and 50-60µm) on the mechanical properties of the syntactic foam composites with focus on flexural strength, modulus, and fracture surfaces were investigated. The particle sizes were varied into five volume fractions (5, 10, 15, 20, and 25vol%). The results shows that highest flexural strength is 89MPa at 5 vol% fraction of 50-60µm particles size variation which is 69% increase than the neat epoxy. This implies that the incorporation of HGM filler volume fraction and size variation has a strong effect on the flexural strength and bending modulus of syntactic foam. The microstructure of the fracture surfaces and the viscoelastic properties was determined and reported accordingly.

In quantum many-body systems, a Hamiltonian is called an ``extensive entropy generator'' if starting from a random product state the entanglement entropy obeys a volume law at long times with overwhelming probability. We prove that (i) any Hamiltonian whose spectrum has non-degenerate gaps is an extensive entropy generator; (ii) in the space of (geometrically) local Hamiltonians, the non-degenerate gap condition is satisfied almost everywhere. Specializing to many-body localized systems, these results imply the observation stated in the title of Bardarson et al. [PRL 109, 017202 (2012)].

From a scientific standpoint, both temporal and spatial variables must be examined when developing programs for training various soccer scoring techniques (SSTs), but a review of current literature reveals that existing scientific studies have overlooked this combinatory influence. Consequently, there is no reliable theory on temporal-spatial identification when evaluating scoring opportunities. Quantified by using biomechanical modeling, anthropometry, and SSTs found in FIFA Puskás Award (121 nominated goals between 2009 and 2020), it is found that players’ proprioceptive/effective shooting volume (i.e. players’ attack space) could be sevenfold the currently-practiced shooting volume. The ignorance of some SSTs’ training leads to the underuse of the potential shooting volume. These overlooked SSTs are airborne and/or acrobatic techniques, perceived as high-risk and low-reward. Relying on the talent of an athlete to improvise on the fly can hardly be considered as a viable coaching strategy. Therefore, for developing science-based SST training regimes, groundbreaking studies are needed to: 1) expand the perception of shooting volume, and 2) entrain one-touch-shot techniques (airborne/acrobatic) within this volume, in short, Focusing-on-Time-in-Space. Whence, the new temporal-spatial theory could guide future researches and develop novel training programs. An increase of airborne/acrobatic goals would ultimately further enhance the excitement of the game.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

Nasopharyngeal carcinoma (NPC) has not been thoroughly studied, and the pathogenesis of NPC is unclear. Scientists have neither discovered effective therapies nor achieved a desirable prognosis. Some studies have found that the regulation of intra- and extracellular ion channels hinges directly on cell apoptosis, and treatment with Gambogenic acid (GNA) brings changes to the volume-sensitive outwardly rectifying chloride (VSOR Cl-) current of CNE-2Z cells recorded by the patch clamp method. Nevertheless, rarely have any researchers probed into the relevance between this variation and the anti-tumor mechanism of GNA. This paper is suggested that GNA activates the VSOR Cl- current on the CNE-2Z cell membrane, and the activation of VSOR Cl- currents by GNA in CNE-2Z cells is blocked by the chloride channel blockers DIDS and DCPIB. GNA induces the down-regulation of GRP78 and up-regulation of ATF4 as well as chop proteins, which is evidence for the induction of CNE-2Z cell apoptosis, and this correlates with ER stress. GNA can activate the VSOR Cl- channel and lead to the occurrence of ER stress, thus inducing the apoptosis of CNE-2Z cells and inhibiting the proliferation of CNE-2Z cells.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

Objective: To explore three novel fasting blood glucose (FBG)-based novel indicators, including FBG-to-albumin ratio (FAR), FBG-to-lymphocytes ratio (FLR), and FBG-to-hemoglobin ratio (FHR), in predicting prognosis and detecting metastasis for patients with pancreatic neuroendocrine neoplasms after resection. Materials and methods: A total of 178 pNEN patients underwent surgical resection were included in this study. Receiver operating characteristic (ROC) curves were used to evaluate the diagnosis values of FAR, FLR, and FHR, and the cut-off values were obtained for further analyses. Univariate and multivariate analyses were conducted to determine the independent predictors. The Kaplan-Meier method was used to evaluate the progression-free survival (PFS) and overall survival (OS) of the pNEN patients. Results: The optimal cut-off values of FAR, FLR, and FHR were 0.17, 2.85, and 0.028, respectively. As for PFS, the area under the curve (AUC) was 0.693 for FAR, 0.690 for FLR, and 0.661 for FHR, respectively. The AUC was 0.770, 0.692, and 0.715 accordingly for OS. The groups with lower FAR, FLR, and FHR were significantly associated with prolonged PFS and OS (p < 0.05). In patients with metastasis, the lower FAR group was correlated with significantly longer PFS and OS (p = 0.022 and 0.002, respectively). The FLR was an independent predictor of PFS in pNEN patients, and the FAR was a predictor of OS. FAR was an independent indicator of PFS in patients with metastasis. Conclusion: Preoperative FAR, FLR, and FHR are effective in predicting the prognosis of pNEN patients and detecting the synchronous metastases.

Objective: The current study aimed to delineate the relationship of furin with inflammation while cervical intraepithelial neoplasia progresses to cancer. Study Design:This cross-sectional study included 81 women who required colposcopic examinations. The study groups were formed based on pathological results: Group I included women with cervical intraepithelial neoplasia (CIN) I (n=30); Group II included women with CIN II-III (n=28); and Group III included women with cervical cancer (CC) (n=23). Furin, ki-67, and p16 levels were evaluated based on immunostaining intensity. The inflammatory indices were calculated parallel with the literature from routine blood samples retrieved within one week before the procedure. Results:Furin expression gradually increased from CIN I to CIN II-III and from CIN II-III to CC, respectively (p < .001, p = .005). The NLR, MLR, PLR, and SII were significantly higher in the CC group (p < .001). ROC curve analysis unveiled that NLR, MLR, PLR and SII predicted the presence of CC with a cutoff value of 2.39 for NLR (sensitivity: 91.3%, specificity: 63.8%, AUROC: 0.79, p < .001); a cutoff value of 0.27 for MLR (sensitivity: 78.3%, specificity: 72.4%, AUROC: 0.77, p = .009); a cutoff value of 123 for PLR (sensitivity: 100%, specificity: 41.4%, AUROC: 0.70, p = .04); and a cutoff value of 747 for SII (sensitivity: 69.6%, specificity: 90.7%, AUROC: 0.71, p = .014). Conclusion:Furin expression increased gradually in parallel to the severity of cervical intraepithelial neoplasia. The inflammatory indices were higher in the presence of CC and denoted good discrimination ability for predicting cervical cancer.

The Olympic Games are a sporting event and a catalyst for urban development in the host city. In this study, we utilized remote sensing and GIS techniques to examine the impact of the Olympic infrastructure on the surface temperature of urban areas. Using Landsat Series Collection 2 Tier 1 Level 2 data, cloud computing, and Google Earth Engine (GEE) methods, this study examines the effects of various Olympic Games facility urban planning in different historical moments and location typologies: monocentric, polycentric, peripheric and clustered Olympic ring. The GEE code applies to the Olympic Games from Paris’24 to Munich’72. However, this paper focuses specifically on the representative cases of Paris’24, Tokyo’20, Rio’16, Beijing’08, Sydney’00, Barcelona’92, Seoul’88, and Montreal’76. The study is not only concerned with obtaining absolute Land Surface Temperatures (LST), but rather the relative influence of mega-event infrastructures on mitigating or increasing the urban heat. As such, locally Normalized Land Surface Temperature (NLST) was utilized for this purpose. In some cities (Paris, Tokyo, Beijing, and Barcelona), it is identified that Olympic planning has resulted in the development of green spaces, creating "green spots" that contribute to lower-than-average temperatures. However, it should be noted that there is a significant variation in temperature within intensely built-up areas, such as Olympic villages and the surrounding areas of the Olympic stadium, which can become “hotspots”. Therefore, it is important to acknowledge that different planning typologies of Olympic infrastructure can have varying impacts on city heat islands, with the polycentric and clustered Olympic ring typologies displaying a mitigating effect. This research contributes to a cloud computing method that can be updated for future Olympic Games or adapted for other mega-events and utilizes a widely available remote sensing data source to study a specific urban planning context.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

This review provides a comprehensive analysis of the pelvic plexus and its regulation across various mammalian species, including rats, cats, dogs, and pigs. The pelvic and hypogastric nerves play crucial roles in regulating pelvic functions such as micturition, defecation, and erection. The anatomical organization of these nerves varies, forming either well-defined ganglia or complex plexuses. Despite these variations, the neurons within these structures are consistently regulated by key neurotransmitters—norepinephrine and acetylcholine. These neurons also possess receptors for testosterone and prolactin, particularly in rats, indicating the significant role of these hormones in neuronal function and development. Moreover, neuropeptides such as vasoactive intestinal peptide (VIP), substance P, neuropeptide Y (NPY), somatostatin (SOM), galanin (GAL), and calcitonin gene-related peptide (CGRP) are co-released with neurotransmitters to modulate pelvic functions. This review highlights the complex interplay between neurotransmitters, neuropeptides, and hormones in regulating pelvic physiology and emphasizes the importance of hormonal regulation in maintaining the functionality and health of the pelvic plexus across different species.

In recent years, urbanization and industrialization have significantly increased the levels of outdoor noise pollution, affecting the quality of life in residential areas. In Uzbekistan, rapid development in urban centers has led to heightened concerns about the impact of noise on residents' health and well-being. Noise pollution can result from various sources, including traffic, construction, and industrial activities, causing disturbances and potential health issues such as stress, sleep disorders, and cardiovascular problems. Addressing this issue is crucial for creating a healthier living environment. This article explores effective strategies for mitigating the impact of outdoor noise on residential buildings in Uzbekistan.

As previous study in many countries shown that stroke patient onsets are not distributed randomly, but associate with meteorological factors. However, the relationship between stroke occurence and meteorological factors remain unknown in mountain area in Guizhou China. This paper firstly introduces multi-source fusion data which is integrated by the mountain meteorological factor, geographic mapping elevation information data and stroke population monitoring of Guizhou province. Mainly elaborates from a few aspects, which concludes data collection, data sorting, data extraction, data cleaning and data production in detail. A completed and detailed meteorological stroke data set was successfully established and multi-source data fusion was realized by the use of Gbase and unified data service interface of Guizhou meteorological big data cloud platform. And we report the impact of meteorological variables in Guizhou mountain area climate on stroke. In this study, we performed a statistical fusion data between January 2017 and December 2020 about stroke incidence rate and meteorological factors respectively, for instance, concerning the mean (Mean), maximum (Max), minimum (Min), median (Median), standard deviation (Std) . We calculated stroke rates (date stroke occurence)/(year stroke occurence) and we investigated the distribution of days included in the label. Results: the distribution of the incidence rate basically conforms to the normal distribution with the label Max 0.007399, label Min 0.000204, label Mean 0.002738, label Median 0.002643, label Std 0.00076. We observed a positive significant correlation of stroke incidence rate directly proportional to the daily temperature difference (between 0 and 20 degrees Celsius), as the value of this factor exhibits variation larger, the incidence rate is gradually increasing. And we investigated from the Pearson correlation coefficients that stroke incidence increasing when meteorological factors at low humidity (less than 40% (RH 80%), temperature higher than 31℃); the 24-hour daily temperature difference varies between 6 and 10℃ (6

Globally, rice is one of the most important staple food crops. The most significant metric for evaluating the rice growth and productivity is the Leaf Area Index (LAI), which can be effectively monitored using remote sensing data. Hyperspectral remote sensing provides contiguous bands at narrow wavelengths for mapping LAI at various rice phenological stages and it is functionally related to canopy spectral reflectance. Hyperspectral signatures for different phases of rice crop growth was recorded using Airborne Visible Near-Infrared Imaging Spectrometer - Next Generation (AVIRIS-NG) along with corresponding ground based observations. Ground based hyperspectral canopy spectral reflectance measurements was recorded with FieldSpec 3 Hi-Res spectroradiometer (ASD Inc., USA; spectral range: 350-2500 nm) and LAI data from 132 farmer’s fields in Southern India. Among 29 hyperspectral vegetation indices tested, eight were found promising for mapping rice LAI at various phenological stages. Among all the growth stages, elongation stage was the most accurately estimated using vegetation indices that exhibited significant correlation with the airborne hyperspectral reflectance. The validation of hyperspectral vegetation indices revealed that the best fit model for estimating rice LAI was mND705 (red-edge, blue and NIR bands) at seedling and elongation, SAVI (red and NIR bands) at tillering and WDRVI (red and NIR bands) at booting stage.

The Qinghai-Tibetan Plateau area (QTPA) features a unique environment that has witnessed the selective breeding of diverse breeds of domestic livestock, exhibiting remarkable adaptability. Nevertheless, Anaplasma spp., Rickettsia spp., Coxiella spp., and Borrelia spp. represent tick-borne bacterial pathogens that pose a global threat and have substantial impacts on both human and animal health, as well as on the economy of animal husbandry within the Qinghai-Tibetan plateau area. In this study, a total of 428 samples were systematically collected from 20 distinct areas within the Qinghai plateau. The samples included 62 ticks and 366 blood samples obtained from diverse animal species, to detect the presence of Anaplasma spp., Rickettsia spp., Coxiella spp., and Borrelia spp. The prevalence of infection in this study was determined as follows: Anaplasma bovis accounted for 16.4% (70/428), A. capra for 4.7% (20/428), A. ovis for 5.8% (25/428), Borrelia burgdorferi sensu lato for 6.3% (27/428), Coxiella burnetii for 0.7% (3/428), and Rickettsia spp. for 0.5% (2/428). Notably, no cases of A. marginale and A. phagocytophilum infections were observed in this study. The findings revealed an elevated presence of these pathogens in Tibetan sheep and goats, with no infections detected in yaks, Bactrian camels, donkeys, and horses. To the best of our knowledge, this study represents the first investigation of tick-borne bacterial pathogens infecting goats, cattle, horses, and donkeys within the Qinghai plateau of the Qinghai-Tibetan Plateau Area. Consequently, our findings contribute valuable insights into the distribution and genetic diversity of Anaplasma spp., Rickettsia spp., Coxiella spp., and Borrelia spp. within China.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

In Ethiopia, land degradation in the form of gully development and soil nutrient depletion is a very serious issue. The goal of this study is to determine how different types of land management practices and slope positions affect particular soil physico-chemical characteristics in the Agamssa watershed. Using systematic sampling techniques, soil samples were taken using a sampling quadrat (15 * 15 m) that was placed 50 m apart from one another. A total of 54 quadrats were planted at three slope positions: upper (>15%), middle (10–15%), and foot (3–10%) slope respectively. 18 composite soil samples were then. A two-way ANOVA was used to analyze the data, and the Least Significant Difference (LSD) test was used to separate the means at p ≤ 0.05. According to the study's findings, the value of most soil physical and chemical characteristics was higher in closed area than on open grazing land, as well as at foot slope position compared to middle and upper slope positions. The higher mean value (7.3 ppm) was recorded at the foot slope, while the lower mean value (4.9 ppm) was found at the upper slope position. The exchangeable cations such as Mg+2, K+, and Na+ were significantly (p≤ 0.01) affected by the main effect of land-use types. The higher mean values of Mg+2 (9.70 mq/100g), K+ (0.38 mq/100 g), and Na+ (0.035 mq/100 g) were found at area closure, whereas the lower mean values of Mg+2 (7.33 mq/100g), K+ (0.30 mq/100 g), and Na+ (0.027 mq/100g) were recorded at open grazing land. It was able to conclude this study that area closure enhances the physical and chemical qualities of soil and recovers woody plant species. Therefore, converting open grazing land into a closure area is advised.

In the context of the rural revitalization strategy, it is urgent to accurately grasp the spatial differentiation characteristics and influencing factors of rural settlements in underdeveloped arid inland river basins. Taking the Shiyang River Basin as an example, the rural settlements from 2000 to 2019 were obtained by visual interpretation using satellite remote sensing data and official statistical data. Following the logical of "state characteristics - evolutionary patterns - influence factors - layout optimization", the average nearest index, gravity-center migration model, spatial statistical analysis and other methods were used combine with GIS. The spatiotemporal pattern evolution characteristics of rural settlements in the past 20 years have been analyzed. The results revealed the following: 1) The distribution pattern of rural settlements in the study area is sheet-like and strip-shaped. The projects in the southeast are mostly distributed in a patchy pattern with high density, while the characteristics in the west and north are exactly opposite. The objects in the south are distributed in the alluvial area of rivers, while settlements in the north are located in the oasis area. 2) From 2000 to 2019, the scale of rural settlements in the Shiyang River Basin, where simultaneous occurrence of new-built and disappearing phenomena, shows an expansion trend that fast firstly and then slow. Spatially, rural settlements in the basin show a trend of clustering towards the southwest. 3) The distribution characteristics of rural settlements are close to water and roads, greatly influenced by urban-rural integration and ecological migration. The results will provide scientific basis for accelerating the modernization of rural areas, and the construction of new rural areas according to local conditions.

Delayed atomic layer deposition (ALD) of ZnO, i.e., area selective (AS)-ALD, was successfully achieved on silicon wafers (Si/SiO2) terminated with tris(dimethylamino)methylsilane (TDMAMS). This resist molecule was deposited in a home-built, near atmospheric pressure, flow-through , gas-phase reactor. TDMAMS has been shown to react with Si/SiO2 in a single cycle/reaction and to drastically reduce the number of silanols that remain at the surface. ZnO was deposited in a commercial ALD system using dimethylzinc (DMZ) as the zinc precursor and H2O as the coreactant. Deposition of TDMAMS was confirmed by spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), and wetting. ALD of ZnO, including its selectivity on TDMAMS – terminated Si/SiO2 (Si/SiO2/TDMAMS), was confirmed by in situ ellipsometry, ex situ SE, XPS, and/or high sensitivity – low energy ion scattering (HS-LEIS). The thermal stability of the TDMAMS resist layer, which is an important parameter for AS-ALD, was investigated by heating Si/SiO2/TDMAMS in air and nitrogen at 330 ºC. ALD of ZnO takes place more readily on Si/SiO2/TDMAMS heated in the air than in N2, suggesting greater damage to the surface heated in the air. To better understand the in situ ALD of ZnO, the data were also plotted as the normalized growth per cycle and to show the selectivity. Even one, short pulse of TDMAMS effectively passivates Si/SiO2. TDMAMS can be an effective small molecule inhibitor of ALD of ZnO on Si/SiO2 surfaces.

The sinking of cavities in urban areas is a very important geological risk to which many towns in Puglia are exposed. The study, mapping, geological and speleological description, classification and cataloging of forms and types of cavities is of fundamental importance for each urban center because it is linked to past local anthropic and natural processes, unique to each site. All this could lead to an enhancement of existing underground cavities in urban areas through conservation and continuous monitoring. Unfortunately in many cases these underground cavities have been used as landfills and subsequently abandoned. One of these cavities at the end of March 2007 collapsed in the inhabited center of Gallipoli causing damage to the structures and fortunately not to human lives. In the area relating to the collapsed cavity, a series of geophysical investigations were undertaken with the use of ground penetrating radar methodology in an attempt to delimit the area of collapse and understand the possible types of interventions for restoring the area. In the same area the measures were repeated 16 years later (December 2022) due to another collapse. The results show a much more widespread danger situation.

Our research is in the tangent space of a point on a 4-dimensional Riemannian manifold. Besides the positive definite metric, the manifold is endowed with a tensor structure of type (1,1), whose fourth power is minus the identity. Both structures are compatible and they define an indefinite metric on the manifold. With the help of the indefinite metric we determine a circle in different 2-planes in the tangent space on the manifold, we also calculate the length and area of the circle. On a smooth closed curve such as a circle, we define a vector force field. Further, we obtain the circulation done by the vector force field along the curve, as well as the flux of the curl of this vector force field across the curve. Finally, we find a relation between these two values, which is an analogue of the well known Green’s formula in the Euclidean space.

The Roman economy of the Iberian Peninsula has habitually been characterised in terms of prestige goods and economic activities such as trade, mining and metallurgy. The analysis of plant-based foods –less prestigious but more essential in everyday life– has commonly been marginalised in state-of-the-art reviews. The O Areal saltworks is exceptional in terms of the large number of organic materials it preserves, and the excellent state of that preservation. After its abandonment (end of the 3rd/4th century AD), the saltworks was briefly used as a dumping ground for the surrounding area. The site's archaeobotanical remains, preserved under anoxic, waterlogged conditions, consist of the building materials used at the saltworks, tools and other artefacts, organic objects employed in activities such as fishing, and refuse. The assemblage suggests a wide diversity of species to have been introduced into northwestern Iberia during the Roman Period, including the mulberry, peach, fig, plum, grapevine, and melon. The notable presence of other edible fruit species that normally grew wild during this period, such as chestnut, walnut, stone pine, and cherry trees, might be related to the start of their cultivation.

Evaluation of the effectiveness of protected areas is critical for forest conservation policies and priorities. To evaluate their effectiveness, we used 30-m resolution forest cover change data between 1990 and 2010 for ~4,000 protected areas and analyzed the relationships of the effectiveness of protected areas with socio-economic variables. Our results show that protected areas in the Tropics avoided 83,500 ± 21,200 km2 of deforestation during the 2000s. Brazil’s protected areas have the largest amount of avoided deforestation of 50,000 km2. We also show the amount of international aid received by tropical countries compared to the effectiveness of protected areas. International aid had major benefits in Latin America led by Brazil while tropical Asian countries used the resource ineffectively. Our results demonstrate that protected areas have been relatively more efficient in countries where deforestation pressures were increasing, and governance and forest change monitoring capacity are important factors for enhancing the efficacy of international aid.

The bay is a space barrier for the development of island-type cities and a high-quality waterfront landscape resource. This study takes Xiamen a typical island city in China as an example. First, It use the method of satellite telemetry technology combined with GIS software and spatial syntax, respectively, from the material space level and social space level, to summarize the rapid urbanization process of this city since 1990-2018, focusing on the construction process of three large-scale waterfront park systems in the transition period of inter-island development in it, and comparing the similarities and differences of their spatial forms. Further, from the choice of the axis model and the integrated analysis results, we discuss the spatial efficiency changes. The construction of the three major bay waterfront park systems in this city reflects a huge change in development pattern from lagging construction, synchronous planning, to advanced layout, providing a continuous and variable spatial form for the development of the bay region and improving space efficiency, which one of the important ways to develop and transform island-type cities. We hope to provide the reference for the development including sustainable development of other island cities around the world

Sentinel-2 provides the opportunity to map the snow cover at unprecedented spatial and temporal resolution at global scale. Here we calibrate and evaluate a simple empirical function to estimate the fractional snow cover (FSC) in open terrain using the normalized difference snow index (NDSI) from 20 m resolution Sentinel-2 images. The NDSI is computed from flat surface reflectances after masking cloud and snow-free areas. The NDSI-FSC function is calibrated using Pléiades very high resolution images and evaluated using independent datasets including SPOT 6/7 satellite images, time lapse camera photographs, terrestrial lidar scans and crowd-sourced in situ measurements. The calibration results show that the FSC can be represented with a sigmoid-shaped function 0.5×tanh(a×NDSI+b)+0.5 where a = 2.65 and b = -1.42 yielding a root mean square error of 25%. Similar RMSE are obtained with different evaluation datasets with a high topographic variability. With this function, we estimate that the confidence interval on the FSC retrievals is 38% at the 95% confidence level.

Understanding the distribution in drought and floods plays an important role in disaster risk management. The present study aims to explore the trends in the standardized precipitation index and extreme precipitation days in China, as well as to estimate the economic losses they cause. We found that in the Northeast China, northern of North China and northeast of Northwest China were severely affected by drought disasters (average damaged areas were 6.44 million hectares) and the most severe drought trend was located in West China. However, in the north of East China and Central China, the northeastern of the Southwest China was severely affected by flood disasters (average damaged areas were 3.97 million hectares) and the extreme precipitation trend is increasing in the northeastern of the Southwest China. In the Yangtze River basin, there were increasing trends in terms of drought and extreme precipitation, especially in the northeastern of the Southwest China, where accompanied by severe disaster losses. By combining the trends in drought and extreme precipitation days with the distribution of damaged areas, we found that the increasing trend in droughts shifted gradually from north to south, especially in the Southwest China, and the increasing trend in extreme precipitation gradually shifted from south to north.

The urban mangrove of the Vitória Bay, Espírito Santo, Southern Brazil suffers from anthropogenic impacts, which interfere in the foliar spectral response of its species. Identifying the spectral behavior of these species and creating regression models to indirectly obtain structure data like the Leaf Area Index (LAI) are powerful environmental monitoring tools. In this study, LAI was obtained in 32 plots distributed in four stations. In situ LAI regression analysis with the SAVI resulted in significant positive relationships (r² = 0.58). Forest variability regarding the degree of maturity and structural heterogeneity and LAI influenced the adjustment of vegetation indices (VIs). The highest regression values were obtained for the homogeneous field data, represented by R. mangle plots, which also had higher LAI values. The same field data were correlated with SAVI of a RapidEye image for comparison purposes. The results showed that, images obtained by a UAV have higher spatial resolution than the Rapideye image, and therefore had a greater influence of the background. Another point is that the statistical analysis of the field data with the IVs obtained from the RapidEye image did not present high regression coefficient (r² = 0.7), suggesting that the use of VIs applied to the study of urban mangroves needs to be better evaluated, observing the factors that influence the leaf spectral response.

The main objective of this work is to investigate the temporal variation of PM10 concentrations within the urban area of Athens during the years 2001-2015. For this purpose, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) is recorded for a 15-year period (2001-2015) in two different monitoring stations located in the urban area of Athens. The results show a totally different behavior of PM10 concentrations between the Athens city center and the suburban areas. It seems that in the city center the main sources of PM10 are traffic and heating systems especially during the cold period of the year. Furthermore, in the city center a significant seasonal variation was found with high concentrations during the cold period of the year and lower concentrations during the warm period of the year. Moreover, it was found that during the weekends, there is a decrease in PM10 concentrations probably due to the fact that majority of people do not use their vehicles. Finally, for both locations a significant temporal decreasing trend of the mean annual PM10 concentrations was found which indicates that during the last years, there have been improvements towards a better air quality.

(1) Background: Little research has been done on professionals' perceptions of institutions and governments during epidemics. We aim to create a profile of physicians who feel they can raise public health issues with relevant institutions during a pandemic. (2) Methods: A total of 1285 Romanian physicians completed an online survey as part of a larger study. We used binary logistic regression to profile physicians who felt able to raise public health issues with relevant institutions; (3) Results: Five predictors could differentiate between respondents who tended to agree with the trust statement and those who tended to disagree: feeling safe at work during the pandemic, considering the financial incentive worth the risk, receiving training on the use of protective equipment, having the same values as colleagues, and enjoying work as much as before the pandemic; (4) Conclusions: Physicians who trust the system to raise public health issues with the appropriate institutions feel they share the same values as their colleagues, say they were trained in the use of protective equipment used during the pandemic, felt they were safe at work during the pandemic, enjoyed their work as much as before the pandemic, and felt the financial bonus justified the risk.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Fire-tolerant eucalypt forests of south eastern Australia are assumed to fully recover from even the most intense fires but surprisingly very few studies have quantitatively assessed that recovery. Accurate assessment of horizontal and vertical attributes of tree crowns after fire is essential to understand the fire’s legacy effects on tree growth and on forest structure. In this study, we quantitatively assessed individual tree crowns 8.5 years after a 2009 wildfire that burnt extensive areas of eucalypt forest in temperate Australia. We used airborne lidar data validated with field measurements to estimate multiple metrics that quantified the cover, density, and vertical distribution of individual-tree crowns in 51 plots of 0.05 ha in fire-tolerant eucalypt forest across four wildfire severity types (unburnt, low, moderate, high). Significant differences in the field-assessed mean height of fire scarring as a proportion of tree height, and in the proportions of trees with epicormic (stem) resprouts were consistent with the gradation in fire severity. Linear mixed-effects models indicated persistent effects of both moderate- and high-severity wildfire on tree crown architecture. Trees at high-severity sites had significantly less crown projection area and live crown width as a proportion of total crown width than those at unburnt and low-severity sites. Significant differences in lidar-based metrics (crown cover, evenness, leaf area density profiles) indicated that tree crowns at moderate- and high-severity sites were comparatively narrow and more evenly distributed down the tree stem. These conical-shaped crowns contrasted sharply with the rounded crowns of trees at unburnt and low-severity sites, and likely influenced both tree productivity and the accuracy of biomass allometric equations for nearly a decade after the fire. Our data provide a clear example of the utility of airborne lidar data for quantifying the impacts of disturbances at the scale of individual trees. Quantified effects of contrasting fire severities on the structure of resprouter tree crowns provide a strong basis for interpreting post-fire patterns in forest canopies and vegetation profiles in lidar and other remotely-sensed data at larger scales.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

The increase in the emission of greenhouse gases (GHG) is one of the most important world problems. Decreasing of GHG emission is a big challenge in the future. Transportation sector uses a significant part of petroleum production in the world and it leads to an increase in the emission of GHG. The result of this issue is that population of the world befoul environment of transportation system automatically. Electric Vehicles (EV) have a potentiality to solve a big part of the GHG emission and energy efficiency issues such as stability and reality of energy. The energy actors and their research team determine some targets for 2050; hence, they hope to decrease the world temperature to 6 °C in the best and 2 °C in the normal condition. Fulfillment of these scenarios needs suitable grid infrastructure but in most of the countries, the grid does not have a suitable background to apply those scenarios. In this paper, some problems about energy scenarios, energy storage systems, grid infrastructure and communication systems in supply and demand side of the grid and its solutions have been investigated.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

Sustaining learners’ motivation to keep learning has been concerned for over 60 years in education and SLA. Most research focusing on Japanese university students has contributed lots of theoretical and practical developments, but research focusing on motivations of non-traditional adult learners and those under 18-year-old to learn Chinese is still little even though previous research findings have proved age is one of the key variables influencing learning besides nationalities and Chinese language levels. In order to find an effective treatment for sustainable Chinese language learning in Japan, this study utilized a survey method to analyze the types of Japanese learners’ motivation to learn Chinese via analysis of a moment structures (AMOS), and to compare the differences of the motivation via one-way ANOVA. This study revealed that Japanese learners’ motivation to learn Chinese consists of eight common types, which are “instrumental motivation”, “personal orientation”, “identified regulation”, “Chinese cultural productions”, “integrating into Chinese community”, “external regulation”, “social responsibility”, and “Chinese for academic purposes”. Also, there are similarities and differences existing in the eight motivation types among the Japanese children, adolescents, (non-) traditional adult learners of Chinese as a foreign language (CFL). The findings contribute the understanding of motivation types and differences among the four aged Japanese learners to teachers of teaching Chinese to speakers of other languages (TCSOL), and to future research further exploring how differently aged Japanese learners can have and use a higher motivation as a main drive to learn Chinese language as a lifelong business.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

Here, our data provide the first evidence for the existence of a previously unknown receptive system formed by novel DNA- and RNA-based receptors in eukaryotes. This system, named the TR-system, is capable of recognizing and generating a response to different environmental factors and has been shown to orchestrate major vital functions of fungi, mammalian cells, and plants.Recently, we discovered the existence of a similar regulatory system in prokaryotes. These DNA- and RNA-based receptors are localized outside of the membrane forming a type of a network around cells that respond to a variety of chemical, biological, and physical factors and enabled the TR-system to regulate major aspects of eukaryotic cell life as follows: growth, including reproduction and development of multicellular structures; sensitivity to temperature, geomagnetic field, UV, light, and hormones; interaction with viruses; gene expression, recognition and utilization of nutrients. The TR-system was also implicated in cell memory formation and was determined to be responsible for its maintenance and the forgetting of preceding events. This system is the most distant receptive and regulatory system of the cell that regulates interactions with the outer environment and governs the functions of other receptor-mediated signaling pathways.