Modeling the reaction time required for the removal of chemical oxygen demand (COD) from wastewater is important because can be an indicator of harmful pollutants that may pose risks to human health.. Here, we evaluate the use of an inverse artificial neural network (ANNi) to optimize the removal of COD from aqueous herbicide solutions using sonophotocatalysis as the treatment process.. This algorithm takes the operating conditions as input and estimates the optimal reaction time to reach the required effluent COD. This model was validated by comparison with both experimental measurements and simulated analysis, resulting in low error (0.5%), high Pearson correlation (R2 = 0.9956), and short computing time (less than one minute). The results for the proposed methodology (ANNi-GAs) were efficient and attractive in a reasonable way providing a satisfactory picture of the relationships between the optimal input parameters. Such parameters control the degradation process of herbicides online and can be used to predict the behavior of COD removal, thus taking actions to reduce the impact of aqueous treatment with alazine and gesaprim herbicides on aquatic, soil biota, and human health. Therefore, this technique constitutes a promising framework for predicting the environmental impact of herbicides within a tolerable degree of error.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

This study addresses the prediction of recurring failures in water supply networks, a complex and costly task, but essential for the effective maintenance of these vital infrastructures. Using historical failure data provided by Companhia de Água e Esgotos da Paraíba (CAGEPA), the research focuses on predicting the time until the next failure at specific points in the network. The authors divided the failures into two categories: Occurrences of New Faults (ONF) and Recurrences of Faults (RF). To make the predictions, they used predictive models based on Machine Learning, more specifically on MLP (Multi Layer Perceptron) neural networks. The study revealed that, by analyzing data from past failures and considering factors such as altitude, number of failures on the same street and days between failures, it is possible to achieve an accuracy greater than 80% in predicting failures within a 90-day interval. This demonstrates the feasibility of using fault history to predict future water supply outages with significant accuracy. These forecasts allow water utilities to plan and optimize their maintenance, minimizing inconvenience and losses. The article contributes to the field of water infrastructure management by suggesting that the data-driven approach can be applied in other cities or in networks of different types, such as energy or communication networks. The conclusions highlight the importance of data collection and analysis in preventing failures and optimizing water utilities’ resources.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

In the moist environment of soil-water-air, there is a problem of low accuracy in monitoring Volatile Organic Compounds (VOCs) using a Photoionization Detector (PID). This paper analyzes the reasons for the low accuracy of the traditional Support Vector Machine (SVM) regression method. To address the issue, the PID signal is subjected to feature extraction and Principal Component Analysis (PCA) to reduce the data dimensionality. Moreover, the optimal SVM parameters are selected using a Genetic Algorithm (GA), and a combined approach of SVM regression with PCA and GA is utilized for PID signal regression analysis. And the effectiveness of the method is validated through extensive experiments and simulations. Furthermore, the influence of the sample quantity on the regression accuracy is analyzed, enabling accurate monitoring of VOCs concentration in a moist environment.

Aquatic ecosystems are often subject to degradation due to various environmental stressors. The accumulation of an organic sediment layer causes shallowing, algal blooms, and hypertrophy in water reservoirs. The processes of overgrowth and shallowing lead to a reduction in the ecosystem services provided by the reservoir as well as may potentially cause the disappearance of the water body. To address these challenges and restore the ecological balance of water reservoirs, effective and sustainable revitalisation methods are essential. In recent years, biotechnological approaches, particularly utilizing microbiological interventions, have emerged as promising strategies for water reservoir revitalization. Microorganisms, with their remarkable ability to degrade pollutants and enhance nutrient cycling, offer great potential in remediating environmental issues in a natural and eco-friendly manner. The article presents the results of a study of 34 Polish reservoirs subjected to reclamation with microbial biopreparations from 2014 to 2023. The results of changes in bottom sediment reduction, water transparency, dissolved oxygen concentration, and water turbidity are presented. Reduction of and morphological changes in the fraction of soft organic sediments, an improvement in the oxygen profile of the bottom and surface water layers, and an increase of water transparency were observed after the reclamation with the use of biopreparations.

: With the increase in demand for non-dairy starter cultures and probiotic bacteria as carriers, the use of legumes (also called pulses) as an alternative has gained momentum. In this study, we investigated the diversity of bacterial communities in samples of pigeon pea (Cajanus cajan L. Millsp.) soaked in water for 12 h and 24 h. We soaked 500 g of pigeon pea in sterile distilled water at room temperature (± 25 °C) for 12 h and 24 h; 10 mL of the soaking water was then collected to measure the bacterial diversity using a metataxonomic analysis. The V1–V9 regions on the 16S ribosomal RNA gene were amplified using 27F and 1492R primers under specific polymerase chain reaction conditions for the bacterial identification. Genomic DNA (130 ng) was sequenced on a R9.4 flow cell by Oxford Nanopore Technologies using a GridION sequencer. Library preparations were initiated using a Native Barcoding Kit 24 V14 (SQK-NBD114.24). Primary data were acquired using MinKNOW version 22.05.7. A total of 13 bacterial families and 89 genera were identified in the pigeon pea sample soaked for 12 h; 26 families and 90 genera were identified in the pigeon pea sample soaked for 24 h. Among the bacterial families identified, the five predominant families in both samples were Enterobacteriaceae, Erwiniaceae, Yersiniaceae, Pectobacteriaceae, and Lactobacillaceae. According to the relative abundance of the identified bacterial genera, the following nine genera were predominant in both samples: Enterobacter, Klebsiella, Citrobacter, Pantoea, Kosakonia, Pseudoenterobacter, Pluralibacter, Leclercia, and Kluyvera. At a genus level, a slight increase in the abundance of Klebsiella, Kosakonia, and Pluralibacter and a slight decrease in the abundance of Citrobacter were observed after prolonged incubation from 12 h to 24 h. The values of five diversity indices revealed that the sample soaked in water for 24 h had a richer bacterial abundance and diversity than the 12 h sample. Shannon and Simpson values revealed a higher bacterial diversity in the sample collected at 24 h than the sample collected at 12 h. Species observations and abundance-based coverage estimator (ACE) values demonstrated that the sample collected at 24 h harbored a higher bacterial richness than the sample collected at 12 h. These findings indicated that the bacterial diversity in the pigeon pea samples increased with the soaking time. The bacterial communities during the soaking of the pigeon pea samples were dominated by the Enterobacteriaceae family and Enterobacter genus. The presence of bacterial genera such as Lacticaseibacillus, Lentilactobacillus, and Secundilactobacillus was notable because of their importance as starter cultures for fermented plant-based milk products, including pigeon pea beverages for lactose-intolerant individuals or individuals with malnutrition.

The plant water status is crucial for growth and production, but the current climate change scenario makes it challenging to match the water plant demand. Blueberry is an economically important crop and plays an acknowledged role in human health due to its antioxidant compounds. This research aimed to determine whether exogenous methyl jasmonate application improves the antioxidant defense mechanisms for protecting the photosynthetic performance in blueberry plants under the stress condition of water deficit. A greenhouse experiment was carried out under a 16-h light period; 20ºC; and 60-80% relative humidity for 2 weeks before treatment application of methyl jasmonate (MeJA) to blueberry plants (Vaccinium corymbosum, Brigitta cultivar). The following treatments were maintained for 7-days: (i) 80% field capacity (NoWD); (ii) 80% field capacity plus MeJA application (NoWD + MeJA); (iii) 20% field capacity (WD); and (iv) 20% field capacity plus MeJA application (WD + MeJA). The MeJA was sprayed as an aqueous solution of 10 µM MeJA (Sigma-Aldrich) over the plant's foliar system. At the end of the assay; blueberry leaves were analyzed for the relative water content; specific leaf area; lipid peroxidation; total antioxidant activity; total phenols; total anthocyanins; anthocyanidin compounds and photosynthetic performance. Brigitta cultivar showed a significant decrease in the oxidative stress at leaf levels; with an increase in antioxidant activity; phenolic compounds; total anthocyanins; delphinidin; petunidin; antheraxanthin; zeaxanthin; and an improvement in photosynthetic performance parameters. Blueberry Brigitta cultivar was shown to be susceptible to WD decreased mainly photosynthesis. However; the MeJA application on leaves induced metabolic changes; through an increase of antioxidant strategy within the plant to counteract the negative effects of WD; protecting the photosynthetic apparatus; which allows the Brigitta cultivar to withstand the period of WD.

Conical emission is a typical nonlinear phenomenon that occurs when the femtosecond laser pulses interact with transparent media. In this work, the conical emission induced by two kinds of typical vortex beams (i.e., Laguerre-Gaussian (LG) and Bessel-Gaussian (BG) beams) in water is experimentally studied. By recording the light spots of different wavelengths on the screen, the characteristics of the conical emission induced by femtosecond vortex beams are studied. It is found that the spots of the supercontinuum induced by the two kinds of vortex beams differ greatly from each other: The spots of the supercontinuum induced by the BG beam are a set of concentric rings like a rainbow with a white center, while the whit light spot in the case of the LG beam are a circular white disk, which is different from the commonly observed white light spots. By measuring the maximum divergence angle, it is observed that the divergence angle increases with the decrease of the wavelength, while the TC merely affects the divergence angle, which is explained from the formation mechanism of conical emission in terms of self-phase modulation. We hope this work can be helpful to the understanding of interaction between the intense laser pulses and matters.

Veterinary antibiotics (VAs) have been indiscriminately used in animal feed for the past five decades to increase and ensure profits with negligible environmental considerations. The VAs amoxicillin (AMX), chlortetracycline (CTC), and oxytetracycline (OTC), which can be unintentionally introduced by irrigation water during rice cultivation, were evaluated for their phytotoxic effects, absorption-translocation into plants, and soil residues using a randomized complete block design. It was found that exposure to VAs can severely affect the photosynthetic pathway of rice plants. The uptake and translocation of VAs by rice plants varied significantly. CTC and OTC translocated more easily than AMX, a member of the β-lactam class, which accumulated at the lowest concentration compared to CTC and OTC across all treatments. Rice yield was about 4.3 - 5.7% lower in the experimental plots that received fifty-fold the background levels of VAs compared to the control. The findings indicate that these widely used veterinary antibiotics can hamper crop production, leave residues in the soil, and constitute a risk to human health if introduced into the agro-ecosystem unintentionally.

Despite the popularity of infant swimming programs, no evidence exists to determine whether they influence infants’ judgements and behavior when confronted with bodies of water. In the current study we examined whether the total number of swimming sessions an infant had participated in predicted whether they avoided a body of water they could enter via an edge (n = 101 infants) or a slope (n = 77 infants). An initial regression analysis revealed no association between the number of sessions and avoidance of the water via either type of entry. However, a secondary analysis of infants who had participated in fewer or more than 10 sessions revealed a significant interaction between number of sessions and type of entry into the water. Infants who participated in more than 10 sessions were more likely to avoid the water if they could access it via an edge but significantly more likely to enter the water if they could access it via a slope. Because we tested the two groups of infants in different countries, further research is warranted to determine if cultural differences in child rearing practices or variations in the content and/or teaching of the swimming programs might explain these intriguing findings.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

Growing water shortages for large regions of the arid regions of the world, are likely to become more recurrent as climate change impacts grow. Countries across the world are facing water security difficulties that stem from population growth, urbanization, and rapid industrialization. The use of behavioral nudges methods implemented to encourage a socially desired behavior at a low to zero cost, has been an effective method at reducing water consumption in places where they have been deployed. For example, studies in California USA, Barcelona Spain, and Australia indicate that adoption of nudges give significant positive results in water consumption reduction. We describe some of the barriers that make it difficult to implement behavioral nudges to address the water crises in Sub-Saharan Africa (SSA). We investigate the literature available in Sub-Saharan Africa and discover that the application of behavioral nudges has been sparingly used for reasons that are not obvious at first glance. Second, we find that the potential impediments to the use of behavioral nudges in SSA to be awareness, inadequate access to science and technology, political systems that are poorly suited for implementing nudging, abundance of multiple ethnic groups that speak different languages, along with other barriers that could challenge implementation of behavioral nudges. In light of those barriers, we present a conceptual model with a potential to address these barriers to behavioral nudging a workable solution in SSA.

In plants, water flows are the major driving force behind the growth and play a crucial role in the life cycle. To study hydrodynamics, methods based on tracking small particles inside water flows occupy a special place. Due to these tools, it is possible to get information about the dynamics of the spatial distribution of the fluxes characteristics. In this paper, using contrast-enhanced MRI, we have shown that gadolinium chelate, used as an MRI contrast agent, marks the structural characteristics of xylem bundles of maize stem nodes and internodes. Supplementing MRI data, a high-precision visualization of xylem vessels by laser scanning microscopy was used to reveal structural and dimensional characteristics of the stem vascular system. In addition, we proposed the concept of using the prototype "Y-type xylem vascular bundles" as a model of the elementary connection of vessels within the vascular system. A Reynolds number can match the microchannel model with the real xylem vessels.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

Water distribution networks are vital infrastructure, needed for providing consumers with sufficient water of appropriate quality. The cost of construction, operation, and maintenance of such networks is extremely large. The problem of optimization of a water distribution network is governed by the type of water distribution network and the size of pipelines placed in the distribution network. This problem of the optimal diameter allocation of pipes in a distribution network has been heavily researched over the past few decades. This study describes the development of a computer program, ‘Smart Optimization Program for Water Distribution Networks’ (SOP–WDN), which applies Genetic Algorithm to the problem of the least-cost design of water distribution networks. SOP–WDN demonstrates the application of an evolutionary optimization technique, Genetic Algorithm, linked with a hydraulic simulation solver EPANET, for the optimal design of water distribution networks. The developed program was applied to three benchmark water distribution network optimization problems and produced consistently good results. SOP–WDN can be utilized as a tool for guiding engineers during the design and rehabilitation of water distribution pipelines.

Titanium dioxide nanoparticles have risen concerns about their possible toxicity and the European Food Safety Authority recently banned the use of TiO2 nano-additive in food products. Following the intent of relating nanomaterials atomic structure with their toxicity without having to conduct large scale experiments on living organisms, we investigate the aggregation of titanium dioxide nanoparticles using a multi-scale technique: starting from ab initio Density Functional Theory to get an accurate determination of the energetics and electronic structure, we switch to classical Molecular Dynamics simulations to calculate the Potential of Mean Force for the connection of two identical nanoparticles in water; the fitting of the latter by a set of mathematical equations is the key for the upscale. Lastly, we perform Brownian Dynamics simulations where each nanoparticle is a spherical bead. This coarsening strategy allows studying the aggregation of a few thousand nanoparticles. Applying this novel procedure, we find three new molecular descriptors, namely, the aggregation free energy and two numerical parameters used to correct the observed deviation from the aggregation kinetic described by the Smoluchowski theory. Molecular descriptors can be fed into QSAR models to predict the toxicity of a material knowing its physicochemical properties, without having to conduct large scale experiments on living organisms.

The present study was aimed at revealing the influence of the mechanical stress induced by water molecules adsorption on the composition of crystalline phases in the ZrO2–3mol%Y2O3-nanoparticles. Three basic methods have been used to determine the phase transition: neutron diffraction, Raman microspectroscopic scanning, and X-ray diffraction. The fact of phase-structural β → α transformation and the simultaneous presence of two polymorphic structural modifications (β is the phase of the tetragonal syngony and α of monoclinic syngony in nanosized particles (9nm)) under normal physical conditions was established by these methods. Satisfactory consistency was achieved between the results obtained using different techniques.

TiO₂ nanorod as a superior nanostructure has attracted a lot of attention to exert in the photocatalytic and photoelectrocatlytic applications in recent years. Nevertheless, its practical usage is restricted by a number of limitations such as the large band gap energy, the low rate of photo-induced carriers generation and the high rate of charge carriers recombination. Therefore in this study, incorporation of TiO₂ nanorod with WO₃ is proposed as a suitable approach to overcome these defects. In this regard, WO₃-TiO₂ nanorod was constructed by a facile one pot hydrothermal method in two incessant steps and was then employed as a potent photoanode for photoelectrocatalytic hydrogen generation. The morphology, elemental compositions and optical properties were characterized by the FESEM, EDS and DRS analysis, respectively. Furthermore, voltammetry analyses were performed to assay the photoelectrochemical features of WO₃-TiO₂ nanorod. The results confirmed that the incorporation of TiO₂ nanorod with WO₃ not only significantly made the band gap energy narrower (from 3eV to 2eV), but also dramatically intensified the photocurrent density and photoconversion efficiency from 1mA.cm^-2 to 1.8mA.cm^-2 and from 0.3% to 0.45%, respectively. As a consequence of improving optical properties and photoelectrochemical features, WO₃-TiO₂ nanorod could generate 2.43 mmol H₂ during 100 min under UV irradiation, which was 1.71 times more than hydrogen generated over pure TiO₂ nanorod

Cyanobacterial species (blue-green algae) constitute the major part of the phytoplanktonic biomass during the summer in freshwater ponds. The aim of the research work was to study the biodiversity of cyanobacteria among 20 different freshwater ponds of the Pudukkottai district of Tamil Nadu, India. The morphological identification of cyanobacterial species was carried out using a trinocular microscope. The results showed that the maximum number of cyanobacterial species belonged to Oscillatoriaceae, Nostocaceae, Microcystaceae, Scenedesmaceae, and Desmidiaceae families. Among 25 different families of Cyanobacteria about 42 distinct species were identified. These results showed that the freshwater ponds of the Pudukkottai district have an abundance of cyanobacteria species.

Grapefruit and lemon pectin obtained from the respective waste citrus peels via hydrodynamic cavitation in water only are powerful, broad-scope antimicrobial alternatives to antibiotics against Gram-negative and -positive pathogens. Dubbed IntegroPectin, these pectic polymers functionalized with citrus flavonoids and terpenes show superior antimicrobial activity when compared to commercial citrus pectin. Similarly to commercial pectin, lemon IntegroPectin determined ca. 3 log reduction of Staphylococcus aureus cells, while an enhanced activity of commercial citrus pectin was detected in the case of Pseudomonas aeruginosa cells with a minimal bactericidal concentration (MBC) of 15 mg mL-1. Although grapefruit and lemon IntegroPectin share equal MBC in the case of P. aeruginosa cells, grapefruit IntegroPectin shows boosted activity upon exposure of S. aureus cells with a 40 mg mL-1 biopolymer concentration being sufficient to achieve complete killing of the bacterial cells. Insight on the mechanism of action of these biocompatible antimicrobials and their effect on bacterial cells, at the morphological level, were obtained indirectly through Fourier Transform Infrared spectroscopy and directly through scanning electron microscopy. In the era of antimicrobial resistance, these results are of great societal and sanitary relevance as they open new avenues to develop innovative antimicrobials for the treatment of polymicrobial infections unlikely to develop drug resistance.

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

GRACE-derived Terrestrial Water Storage Anomalies (TWSA) continue to be used in an expanding array of studies to analyze numerous processes and phenomena related to terrestrial water storage dynamics, including groundwater depletions, lake storage variations, snow, and glacial mass changes, as well as floods, droughts, among others. So far, however, few studies have investigated how the factors that affect total water storage (e.g., precipitation, runoff, soil moisture, evapotranspiration) interact and combine over space and time to produce the mass variations that GRACE detects. This paper is an attempt to fill that gap and stimulate needed research in this area. Using the Nile River Basin as case study, it explicitly analyzes nine hydroclimatic and anthropogenic processes, as well as their relationship to TWS in different climatic zones in the Nile River Basin. The analytic method employed the trends in both the dependent and independent variables applying two geographically multiple regression (GMR) approaches: (i) an unweighted or ordinary least square regression (OLS) model in which the contributions of all variables to TWS variability are deemed equal at all locations; and (ii) a geographically weighted regression (GWR) which assigns a weight to each variable at different locations based on the occurrence of trend clusters, determined by Moran’s cluster index. In both cases, model efficacy was investigated using standard goodness of fit diagnostics. The OLS showed that trends in five variables (i.e., precipitation, runoff, surface water soil moisture, and population density) significantly (p<0.0001) explain the trends in TWSA for the basin at large. However, the models R2 value is only 0.14. In contrast, the GWR produced R2 values ranging between 0.40 and 0.89, with an average of 0.86 and normally distributed standard residuals. The models retained in the GWR differ by climatic zone. The results showed that all nine variables contribute significantly to the trend in TWS in the Tropical region; population density is an important contributor to TWSA variability in all zones; ET and Population density are the only significant variables in the semiarid zone. This type of information is critical for developing robust statistical models for reconstructing time series of proxy GRACE anomalies that predate the launch of the GRACE mission and for gap-filling between GRACE and GRACE-FO.

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy³⁺) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m²·g^-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N₂ is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m²·g^-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g^-1 and 33.52 mg·g^-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

Recently, the environment is being put under constantly increasing pressure. Globally, water shortage is considered as one of the most serious environmental problems which affect human life and plant wealth. Iraq is highly affected by water deficit in many regions. In particular, Al-Najaf region is selected to be under evaluation for the current and future water resources shortage. This study is based on the collected data for rainfall, evaporation, flow-rate, groundwater, water needed for irrigation, and daily uses for the period between 2000 and 2018. The Artificial Neural Network, normal distribution, and lognormal distribution type III are applied for analyzing the collected data in addition to predict the water shortage for year 2050. Results show a water shortage in years 2002, 2004, 2005, and 2017 only for the selected period. A Simulink model is constructed using Matlab to increase the credibility of the estimated results and gives accurate results for the groundwater and surface water needed. Where in 2050, it is found that it needs to use the groundwater source by 0.024 x 10⁹ m³ to support the surface water source which is represented by the Euphrates River. The study shows the extent of inefficient management of water resources in Al-Najaf region.

In the case of vascular plants the process of water loss by leafs and water absorption by the root is well known. There is agreement on the passive nature of long-distance moisture movement in the dead cells of the xylem; however, controversy exists focusing on the long-distance water transport principle. Hales (1726) founded a view of bulk flow based on water suction after experiments with cut twigs. The previous doctrine of long-distance water transport within vessel elements and tracheid of the xylem of intact plants – the relevant cohesion theory in text books – was developed mainly by Boehm (1893), Renner (1911) and Dixon (1914) with plant artefacts. Water movement according to this theory is based on an assumed hydrodynamic bulk fluid flow in xylem in continuous water columns (free of water vapour space), under tension, according to the law of Poiseuille (see e.g. Dixon 1914). Physically hydrodynamics is part of fluid mechanics, as a result Poiseuille’s law is usually valid only for hydrodynamic bulk flow in ideal capillaries (Sutera & Skalak, 1993). Besides the basic requirement for transport, according to cohesion theory, the existence of ideal capillaries is not compatible with either: “Because vessel elements and tracheid do not stand as ideal capillaries. …” (Bresinsky et al. 2008, translated from German). Unlike ideal capillaries, the walls of vessel elements and tracheid interact with the transported water. These walls are able to function as a source or as a sink for the transported water because of interaction with the cell walls. With the interaction, vessel elements and tracheid, part of the xylem, can shrink and swell, unlike ideal capillaries. Because the xylem (in woody plants part of the wood) is inconsistent with the basic law of fluid flow, the equation of mass balance (Zimmermann et al. 2004) and cohesion theory are not strictly followed.Many plant physiologists view the cohesion theory as appropriate, however, this theory remains controver­sial, i.e. by Eisenhut (1988), Laschimke (1990) and Hahn (1993). Nultsch (1996) gives doubts referring to the present doctrine of plant water transport. Zimmermann et al. (2004) reject the cohesion theory and conclude: “... that the arguments of the proponents of the Cohesion Theory are completely misleading” (Zimmermann et al. 2004). Hence cohesion theory can be treated as inapplicable and the question arises: how does water transport in fact function? In the following, it is gone into in more detail. A sorption hypothesis of actual water transport, based on empirical fact, shall be addressed in this paper.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

Semiconductor nanocrystals or quantum dots (QDs), have unique optical and physical properties that make them potential imaging tools in biological and medical applications. However, concerns such as the aqueous dispersivity, toxicity to cells and stability in biological environments may limit the use of QDs in bioapplications. Here, we report an investigation into the cytotoxicity of aqueously dispersed CdSe(S) and CdSe(S)/ZnO core/shell QDs in the presence of human colorectal carcinoma cells (HCT-116) and a human skin fibroblast cell line (WS-1). The cytotoxicity of the precursor solutions used in the synthesis of the CdSe(S) QDs was also determined in the presence of HCT-116 cells and compared to that of the heat-shock protein (Hsp90) inhibitor, 17-AAG. CdSe(S) QDs were found to have a low toxicity at concentrations up to 100 µg/ml, with a decreased cell viability at higher concentrations, indicating a highly dose-dependent response. Meanwhile, CdSe(S)/ZnO core/shell QDs exhibited lower toxicity than uncoated QDs at higher concentrations. Confocal microscopy images of HCT-116 cells after incubation with CdSe(S) and CdSe(S)/ZnO QDs showed that the cells were stable in aqueous concentrations of 100 µg of QDs per ml, with no sign of cell necrosis, confirming the cytotoxicity data. Key words: HCT-116, WS1, water dispersive QDs, aqueous synthesis, cytotoxicity of QDs.

Flushing tap water is often promoted as a simple and low cost approach to reducing water lead exposures. This study evaluated lead reduction when prevailing flush guidelines (30 seconds-2 minutes) are implemented in a city compliant with lead-associated water regulations (New Orleans, LA). Water samples (n=1,497) collected from a convenience sample of 376 residential sites (2015-2017) were analyzed for lead in samples collected: at 1) first draw (n=375), and after incremental flushes of 2) 30-45 seconds (n=375), 3) 2.5-3 minutes (n=373), and 4) 5.5-6 minutes (n=218). There was no significant reduction when compared to the first draw lead level, until the 6 minute flush (p<0.05); but most sites (52%) still had detectable lead (≥1 ppb) after 6 minutes. Older homes (pre-1950) and low occupancy sites had significantly higher WLLs (p<0.05).Each sample type had health-based standard exceedances at over 50% of sites sampled (max: 58 ppb). While flushing is an effective short-term approach to remediate high lead, prevailing flush recommendations are an inconsistently effective exposure prevention measure that can often inadvertently increase exposures. Public health messages should be modified to ensure appropriate application of flushing for specific cities, while acknowledging its short-comings and practical limitations.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

The catastrophic twin earthquakes that struck southern Turkey and northern Syria on February 6 2023, caused massive casualties and extensive damage to infrastructure, with the province of Hatay bearing the brunt of the impact. To investigate the potential of nighttime light (NTL) data for earthquake disaster assessment, we performed an analysis of pre- and post-earthquake NPP-VIIRS and SDGSAT-1 NTL data. The NTL change ratio (NCR) was employed to identify the extent of damage in Hatay Province following the earthquake to assess the impact on affected buildings and populations. NPP-VIIRS daily NTL Time-series data was used to establish an economic recovery framework for earthquake disasters in Hatay Province, assessing regional economic recovery after earthquake. The results revealed a strong correlation between the total reduced NTLs of NPP-VIIRS and SDGSAT-1 and the presence of severely and moderately damaged buildings. Conversely, the correlation with slightly damaged buildings was relatively weaker. Furthermore, the reduced NTLs of NPP-VIIRS provide a more precise identification of all earthquake damage compared to the SDGSAT-1 data, achieving an overall accuracy of 86.21% in earthquake damage identification and a Kappa coefficient of 0.72. In accordance with the earthquake economic recovery framework, as of the end of March 2024, neither the provincial economy nor any of its districts have fully restored to their pre-earthquake levels. The findings offered new and valuable insights into earthquake disaster assessment, assisting decision-makers in accurately assessing the level of disaster risk following an earthquake and efficiently allocating post-earthquake relief funds.

Deep eutectic solvents (DESs) have emerged as viable alternatives to the toxic organic solvents. The most intriguing aspect of these solvents is perhaps the widely varying physicochemical properties emerging from the changes in the constituents that form DESs along with their composition. Based on the constituents, a DES can be hydro-philic/polar or hydrophobic/non-polar rendering vastly varying spectrum of polarity a possibility. DESs formed by mixing urea (U) with hydrated lanthanide salts, lanthanum nitrate hexahydrate (La : U), cerium nitrate hexahydrate (Ce : U), and gadolinium nitrate hexahydrate (Gd : U), respectively, exhibit very high polarity as manifested via probe-reported empirical parameters dipolarity/polarizability (π*). The highest π* of 1.70 exhibited by the DES (Gd : U) in 1 : 2 molar ratio is unprecedented. The π* ranges from 1.50 to 1.70 for these DESs, which is almost the highest reported for any solvent system. The π* decreases with increasing urea in the DES, however, the anomalous trends in H-bond donating acidity (α) and H-bond accepting basicity (β) appear to be due to the hydrated water of the lanthanide salt. The emission band maxima of fluo-rescence probe of “effective” dielectric constant (εeff) of the solubilizing media, py-rene-1-carboxaldehyde (PyCHO), in salt-rich DESs reflect higher cybotactic region di-polarity than even that offered by water. Probe Nile red aggregates readily in these DESs to form non-fluorescent H-aggregates; a characteristic of highly polar solvents. Behavior of probe pyranine also corroborates these outcomes as the (lanthanide salt : urea) DES system supports the formation of deprotonated form of the probe in the excited-state. The (lanthanide salt : urea) DES system offers solubilizing media of exceptionally high polarity, which is bound to expand their application potential.

This research aims to review the educational and research operations of Mahasarakham University and propose development directions for the university to meet sustainable development criteria for ranking as a green university. This involves gathering data and analyzing the results of operations over the past 3 years, then using this analysis to synthesize lessons learned and develop guidelines for sustainable development in the coming years. The study found that the university's policies and strategies implemented following the annual performance evaluation criteria align with the green university assessment criteria for education and research. This has resulted in minor improvements in curriculum for sustainability. However, community service projects for sustainability have increased by 89.10%, while funding for sustainable research and academic publications related to sustainability has decreased. In summary, the projects under the university's development strategy adequately support and drive suitable development activities. Nevertheless, the university must continuously review its operations to adapt to changing contexts, budget constraints, and evolving competition and develop each year sustainably.

Background: Accurate estimation of the spread of SARS-CoV-2 is crucial for guiding public health strategies. Underreporting from PCR-based testing, especially in low- and middle-income countries, often obscures the true extent of exposure and immunity to coronavirus disease 2019 (COVID-19). This study aimed to determine the seroprevalence and antibody levels against SARS-CoV-2 among patients visiting hospital-based sentinel sites in Kenya's Rift Valley region following the Omicron wave. Method: We conducted a cross-sectional study in four hospital-based sentinel sites among patients with acute respiratory infection symptoms. Patients aged six months or older visiting the sites between January 2022 and December 2022, presenting with symptoms of acute respiratory infection, were enrolled. Clinical and sociodemographic data were collected using a structured questionnaire. We used a quantitative ELISA kit to detect IgG antibodies against SARS-CoV-2 S protein in serum samples. Results: Among 557 individuals enrolled in the study, the seroprevalence of SARS-CoV-2 antibodies was 97.8% (n=545). Vaccinated individuals demonstrated significantly higher odds of seropositivity compared to unvaccinated counterparts, with an odds ratio of 3.33 (95% CI: (0.4, 27.87)). While seropositivity remained consistent across age groups, older adults exhibited the highest odds. Site-specific differences in enrolment and vaccination rates highlight potential access-related disparities. Conclusion: Our findings indicate widespread prior exposure to SARS-CoV-2 within the study region, underscoring the significant impact of both natural infection and vaccination efforts in driving SARS-CoV-2 seroprevalence within the Rift Valley region. Despite the underestimation of infections and disparities in vaccination access, this study demonstrates the effectiveness of vaccination for conferring SARS-CoV-2 immunity. Targeted interventions are crucial to address accessibility barriers and vaccine hesitancy, ensuring equitable vaccination coverage.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&amp;E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

The Olympic Games are a sporting event and a catalyst for urban development in the host city. In this study, we utilized remote sensing and GIS techniques to examine the impact of the Olympic infrastructure on the surface temperature of urban areas. Using Landsat Series Collection 2 Tier 1 Level 2 data, cloud computing, and Google Earth Engine (GEE) methods, this study examines the effects of various Olympic Games facility urban planning in different historical moments and location typologies: monocentric, polycentric, peripheric and clustered Olympic ring. The GEE code applies to the Olympic Games from Paris’24 to Munich’72. However, this paper focuses specifically on the representative cases of Paris’24, Tokyo’20, Rio’16, Beijing’08, Sydney’00, Barcelona’92, Seoul’88, and Montreal’76. The study is not only concerned with obtaining absolute Land Surface Temperatures (LST), but rather the relative influence of mega-event infrastructures on mitigating or increasing the urban heat. As such, locally Normalized Land Surface Temperature (NLST) was utilized for this purpose. In some cities (Paris, Tokyo, Beijing, and Barcelona), it is identified that Olympic planning has resulted in the development of green spaces, creating "green spots" that contribute to lower-than-average temperatures. However, it should be noted that there is a significant variation in temperature within intensely built-up areas, such as Olympic villages and the surrounding areas of the Olympic stadium, which can become “hotspots”. Therefore, it is important to acknowledge that different planning typologies of Olympic infrastructure can have varying impacts on city heat islands, with the polycentric and clustered Olympic ring typologies displaying a mitigating effect. This research contributes to a cloud computing method that can be updated for future Olympic Games or adapted for other mega-events and utilizes a widely available remote sensing data source to study a specific urban planning context.

This research aimed to synthesize Polyvinyl fluoride (PVDF) membranes and coat them with Tannic acid (TA) nanoparticles and Polyethylene glycol (PEG) additives so that the membrane's removal efficacy for humic acid (HA) pollutant from agricultural wastewater was investigated. Thus, six membranes with PEG:TA ratios of 0:0, 1:0, 0:1, 1:1, 4:1 and 1:4 were synthesized. Then the membranes' characteristics were identified by FT-IR ATR, FESEM, and AFM analysis, and HA's particle size and zeta potential were also investigated. Based on optimizing effective parameters, the operating pressure of 1.5 bar and HA concentration of 80 ppm were selected as optimal values. The membrane with PEG:TA=4:1, as the optimally modified membrane, had a pure water flux of 446.03 L/m2.h, effluent flux of 72.43 L/m2.h and pollutant removal rate of 86.62% at pH=7 After 60 min had passed. These values for the pristine membrane (PEG:TA=0:0) were 265.64 L/m2.h, 89.39 L/m2.h, and 75.59%, respectively. The results showed that although the effluent flux was lower in the optimized modified membrane than in the pristine membrane, HA removal percentage was increased.

Growth environment greatly alters many facets of pathogen physiology, including pathogenesis and antimicrobial tolerance. The importance of host-mimicking environments for attaining an accurate picture of pathogen behaviour is widely recognised. Whilst this recognition has translated into the extensive development of artificial cystic fibrosis (CF) sputum medium, attempts to mimic the growth environment in other respiratory disease states have been completely neglected. The composition of the airway surface liquid (ASL) in different pulmonary diseases is far less well characterised than CF sputum, making it very difficult for researchers to model these infection environments. In this review we discuss the components of human ASL, how different lung pathologies affect ASL composition, and how different pathogens interact with these components. This will provide researchers interested in mimicking different respiratory environments with the information necessary to design a host-mimicking medium, allowing for better understanding of how to treat pathogens causing infection in these environments.

Purpose: The objective of the study was to qualitatively assess micro-gap dimensions, connecting fitting surface profile and bacterial leakage of machined and cast high gold alloy UCLA abutments, with or without electrodeposited gold coatings attached to external hexagon implants. Materials and methods: 16 plastic UCLA (PUCLA) and 5 machined cast-to UCLA (GUCLA) abutments were cast with a high gold content alloy. 10 were electrolytically gold plated (8 - PUCLA, 2 - GUCLA). All abutments were attached to implants giving 21 implant-abutment combinations (IACs). External perimeter micro-gaps measured with SEM under different illumination and magnification conditions were averaged over three regions. The IACs were examined for E.coli leakage following an initial sterility test. Disassembled combinations were examined with SEM and surface profiles qualitatively assessed. Results: External micro-gap measurements did not reflect the variable connecting surface profiles but average values < 3.5 μm were observed for all IACs. Bacterial transfer was observed in 3 of 5 PUCLA plated and 2 of 5 PUCLA non-plated IACs. No transfer occurred in the 3 GUCLA non-plated or 2 GUCLA plated IACs. Abutment connecting surfaces, both Au plated and not Au plated, showed plastic deformation (smearing) in variable mosaic patterns across the micro-gap. External micro-gap dimensions although not truly reflective of surface connecting profiles averaged < 3.5 μm measured under shadow eliminating silhouette illumination for both cast and pre-machined external hexagon abutments with and without Au plating. Conclusions: Micro-gap dimensions < 5 μm were obtained with both high noble metal cast and pre-machined external hexagon abutments with and without Au electrodeposited on the abutment connecting surface. Regions of intimate contact due to plastic deformation (smearing) of these surfaces was observed. A continuous smeared region around the circumference of the surfaces can provide an effective barrier to egress of E.coli bacteria from the internal regions of the implant under static loading.

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

In this article, a method for the moisture mapping of the soil surface of agrophytocenosis was proposed using neural network based on synchronized radar and multispectral optoelectronic data of Sentinel-1,2. To verify the developed method, data from two experimental plots were used. These plots were located two on irrigated soybean crops. The first of them was located on the right bank (1st plot) and the second one on the left bank (2nd plot) of the down part of Volga River. Two experimental soil moisture geo-datasets were done by measurements and geo-referencing points using gravimetric method (1st plot) and with proximal sensing method (2nd plot) using Soil Moisture Sensor ML3-KIT (THETAKIT, Delta). The soil moisture retrieval algorithm was based on the use of a neural network to predict reflection coefficient of an electromagnetic wave from the soil surface, followed by inversion into soil moisture using a dielectric model that takes into account the soil texture. The input parameter of the neural network was the ratio of the microwave radar vegetation index (calculated on the basis of Sentinel-1 data) to the index (calculated on the basis of data of multispectral optoelectronic channels 8 and 11 of Sentinel-2). Such way calculated index reveals showed a significantly greater dependence on soil moisture than on vegetation height that was been used in previous studies. The retrieved values of soil moisture were compared with the soil moisture measured in-situ. The proposed method with a determination coefficient of 0.44-0.65 and a standard deviation of 2.4%-4.2% for the 1st plot as well as with and of the same metrics for the 2nd allows predicting the soil moisture of both a test plots covered by soybean plants, relative to soil moisture measured in-situ. The conducted research created the scientific basis for a new technology for remote sensing the moisture content of the soil surface of agrophytocenosis as an element of the precision farming system and agroecology.

Ganoderic Acid (GA), a major bioactive compound isolated from an oriental medicinal mushroom, i.e. Ganoderma tsugae, has traditionally been found to have significant medicinal properties. As a result of GA's poor solubility in water, formulation poses several challenges. Additionally, the traditional method of administering it via alcohol always results in unfavorable patient side effects. In order to overcome these problems, Ganoderma Tsugae extracts obtained by ethanol extraction were encapsulated in nanodispersions by ultrasonic cavitation and solvent evaporation to maximise bioavailability. Resultant nanodispersions contained Ganoderic acid in a hydrophobic core with a mean particle size of no more than 200 nm and a very narrow particle distribution. An analysis of the interactions between the control variables and the process optimisation was conducted using the Response Surface Methodology (RSM). Based on the results of the experiment, it was found that the particle size of nanodispersions was influenced by the Hydrophilic-Lipophilic Balance (HLB) number and the evaporation temperature. Moreover, the physical stability of micellar systems is generally determined by the organic phase within them. Regarding formulation stability, the zeta average of the nanodispersions remained virtually unchanged in solutions with different pH levels and short-term storage (14 days) at room temperature. Overall, it has been demonstrated that Ganoderic acid nanodispersions can be efficiently generated by combining ultrasound cavitation and solvent evaporation.

The problems of formation and propagation of surface seismic waves in vertically layered and horizontally inhomogeneous media are studied. A mathematical model has been developed for the propagation of surface seismic waves in an inhomogeneous medium based on the use of the fundamental principles of wave dynamics and Fourier transforms. The existence of various types of groups of these waves is proved, and their main properties are studied. It has been established that the reflection coefficients of different groups of a dispersive wave on models of half-spaces (a layered, inhomogeneous medium) with a sharp velocity differentiation are characterized by the same dependence on the angle of incidence as in the absence of dispersion. In the region of the critical angle, which depends on the period of the incident wave, a local decrease in the intensity of wave reflection is observed, which is associated with the origin of the head dispersive wave. It has been found that the reflection coefficients of Rayleigh waves from low-velocity layers, thin (d / λ2 = 0.205) and thick (d / λ2 = 0.82) are approximately 0.2 ± 0.04 and practically do not change with increasing angle of incidence. On the basis of theoretical studies, it was revealed that reflected surface waves carry information both about the elastic properties of the reflecting medium and about the dimensions of the reflecting horizontal inhomogeneity. An experimental dispersion curve of the group velocity of Rayleigh waves on the Central Asia-Caucasus path has been obtained. The seismic stress state of the "subgrade-base" system was studied. Based on the analysis of the results of numerical experiments, it has been established that in order to obtain a complete picture of the seismically stressed state of the subgrade, it is necessary to take into account the contribution to it of each component of the accelerogram of a real earthquake.

The depletion and environmental problems associated with fossil fuels have encouraged us to look for alternative feedstock that do not compromise food security and the environment. Sorghum is a fast-growing crop that can be harvested twice a year and produces both food and straw that can be utilized in the production of bio-based fuels. In this study, the production of bioethanol and the effects of fermentation parameters on ethanol yield are presented. A sequential pretreatment method was employed, using dilute sulfuric acid (1%) at 125 °C in the first stage and dilute sodium hydroxide (1.25 %) at 90 °C in the second stage. The residues left after the sequential pretreatment stage were hydrolyzed using acid hydrolysis. The sugar concentration of the hydrolysates was determined using the phenol sulfuric acid method, and three hydrolysates having sugar levels of 30.42 g/L, 31.79 g/L, and 32.9875 g/L were selected for fermentation. The ethanol yield was determined after 72 hours of fermentation at 30 °C with varying inoculum sizes (5%, 10%, and 15%) and pH (4.5, 5, and 5.5). With a maximum ethanol yield of 0.617 mL/g (48.742%) produced at a sugar content of 32.9875 g/L, pH of 5, and inoculum size of 15%, statistical analysis showed that all three independent parameters affected ethanol yield. According to these findings, while raising sugar content, inoculum amount, and pH all initially result in higher ethanol yields, doing so further reduces yield. So, in order to increase ethanol yield, fermentation conditions must be carefully managed while producing ethanol from sequential acidic-alkaline pretreated sorghum straw. The strategy followed by using sequential acidic-alkaline pretreatment of sorghum straw provides prospects for efficient and effective production of biofuels from alternative feedstock.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.

Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

The present study aimed at investigating the influence of the concentration of sodium silicate and sodium hexametaphosphate on the dispersion of an aqueous kaolinitic clay slurry regarding further use for the tape casting process. The zeta potential of the kaolinitic clay slurry matched the requirements for tape casting. The addition of magnesite in the kaolinitic slurries tended to increase the zeta potential towards the required limit values. Despite, the further addition of surfactants allowed improving the zeta potential in agreement with the tape casting conditions. Accordingly, the rheological behavior, under continuous and oscillatory flow conditions, of various mixtures of magnesite and a kaolinitic clay was studied. Regarding the pH and the zeta potential measurements, the E–F attraction prevailed at low pH value, and F–F or E–E attraction was predominant at high pH value. All slurries exhibited a shear thinning behavior, which was well-correlated by Herschel–Bulkley model. It appeared that the best stability for the kaolinitic clay slurries was obtained while using 0.4 mass% and 1.2 mass% of sodium hexametaphosphate and sodium silicate respectively. An increase in the magnesite concentration above 6 mass% led to a complex behavior with low cohesion energy due to the occurrence of soluble complexes.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

The detection of microplastics (MPs) in drinking water has emerged as a critical environmental concern, with significant implications for public health. However, the variability in identification methods across studies has made it difficult to compare results, underscoring the urgent need for standardized protocols. This study presents a comprehensive meta-analysis and practical ap-proach to standardizing Fourier Transform Infrared Spectroscopy (FTIR)-based methodologies for detecting MPs in drinking water. By systematically reviewing studies from 2019 to 2023, this research identifies the most effective techniques for MP quantification, with an emphasis on the use of 0.45 μm cellulose nitrate filters and Nile red staining for fluorescence detection. The me-ta-analysis demonstrates consistent results across studies, supported by statistical analysis con-firming the reproducibility and reliability of the methodologies employed. Experimental findings highlight that the cellulose nitrate filter offers superior microplastic retention with low back-ground fluorescence, making it ideal for FTIR analysis. Moreover, the Nile red spray method is recommended for its efficiency and uniformity in staining, and random counting proves to be a rapid and reliable quantification technique. This study advocates for the adoption of standard-ized protocols, particularly in filter selection and staining methods, to ensure accurate and com-parable MP detection. The findings contribute valuable insights for optimizing water treatment processes and provide a solid foundation for future research and regulatory frameworks aimed at mitigating microplastic contamination in water resources.

Microalgae cultivation for biotechnological purposes is an expanding field. Their cultivation is usually performed on a liquid culture medium and require the presence of an energy source. Culture media are water-salt solutions containing nitrogen, sulfur, phosphate sources, with trace of transition metals. Light source supplies energy through photosynthesis process, resulting in metabolic reactions and cell growth. Thanks to the huge number of existing species and their diversity, it is possible to exploit alternative water sources with chemical and physical properties far from the commonly used freshwater media. Among these, oilfield or formation waters (AFW) are saline wastewater produced during oil drilling. They represent over 95 % of the total fluids collected from gas and oil wells during fuel extraction. This study exploits the adaptation capability of a Galdieria sulphuraria strain in different salinity conditions to build up a more feasible microalgae-based platform. Batch cultivation of G. sulphuraria was evaluated in a range from 0 to 20 g/L NaCl in terms of growth rate, metabolite content, photophysiology, and intracellular redox state. Moreover, the same strain has been tested for artificial formation water growth in semicontinuous cultivation mode. In these condition, NaCl preadaptation effect has been assessed too. Results clearly demonstrate that biomass composition is influenced from medium salinity. Strains preadapted in 0 to 20 g/L range of NaCl salinity show almost same cell growth profile and a slightly different ratio between lipids, carbohydrates, and proteins. Pigments content and photophysiology point out that variations of osmotic pressure and ionic strength in medium affect Photosystem II (PSII). Regulation of light harvesting is necessary to trigger metabolism shift toward synthesis of metabolites required in the adaptation process.

The Latin American Giant Observatory (LAGO) is a ground-based extended cosmic rays observatory designed to study transient astrophysical events, the role of the atmosphere on the formation of secondary particles, and space-weather-related phenomena. With the use of a network of Water Cherenkov Detectors, LAGO measures the secondary particle flux, a consequence of the interaction of astroparticles impinging on the Earth with the atmosphere. These interactions yield a flux of secondary particles that can be grouped into three distinct basic constituents: the electromagnetic, muonic, and hadronic components. In this work we extend our previous research by using detailed simulations of the expected atmospheric response to the primary flux and the corresponding response of our WCDs to atmospheric radiation. After implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD, we have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout LAGO distributed detection network and other astroparticles observatories for semi-automated, onboard and real-time data analysis. When a particle enters a Water Cherenkov Detector (WCD), it generates a measurable signal characterized by unique features correlating to the particle’s type and the detector’s specific response. The resulting charge histograms from these signals provide valuable insights into the flux of primary astroparticles and their key characteristics. However, this data is insufficient to effectively distinguish between the contributions of different secondary particles. This research extends our previous investigations, wherein we implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD. We have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. This methodology facilitates the differentiation among particle types and utilizes the detector’s nuanced response to each particle type, thus pinpointing the principal contributors within each group. In this work, we utilize OPTICS to analyze simulated data, further validating the proposed method. We created a simulated dataset by combining the outputs of the ARTI and MEIGA frameworks. This dataset simulates the expected WCD signals produced by the flux of secondary particles during one day at the LAGO site in Bariloche, Argentina, situated at 865 meters above sea level. To achieve this, real-time magnetospheric and local atmospheric conditions for February and March of 2012 were analyzed, and the resultant atmospheric secondary-particle flux was integrated into a specific MEIGA application featuring a comprehensive Geant4 model of the WCD at this LAGO location. The output from MEIGA was modified for effective integration into our machine learning pipeline. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard and real-time data analysis. Our analysis demonstrates that OPTICS can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard data analysis.

The creation of protonated water nanoclusters from amorphous water-ice under laboratory conditions suggests the possible ejection of such nanoclusters from ubiquitous amorphous water-ice-covered cosmic dust to interstellar space. The quantum properties of these quintessential water entities introduce a tantalizing prospect that bridges the origins of dark matter, dark energy, and life in the universe. The quantum-entangled diffuse Rydberg electronic states inherent to cosmic water nanoclusters make them plausible candidates for baryonic dark matter. Moreover, they exhibit the capacity to absorb, through the microscopic dynamical Casimir effect, virtual photons originating from zero-point-energy vacuum fluctuations occurring above the water-nanocluster vibrational frequency cutoff. This selective interaction leaves only vacuum fluctuations below these frequencies with gravitational significance, cancelling the vacuum-energy catastrophe and yielding a shared genesis for dark matter and dark energy. Moreover, this theory extends its implications to the origins of life itself, proposing that RNA protocells on Earth and habitable exoplanets may have emerged from the interactions between cosmic water nanoclusters and prebiotic organic molecules, thus yielding an anthropic narrative. Collectively, these findings coalesce into a cosmological framework depicting a cyclic universe, with cosmic water nanoclusters constituting a quintessence scalar field, instead of adhering to the multiverse concept based on cosmic inflation theory. Recent observations of CMB birefringence support this quintessence.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

The aim of article is to design a calm water resistance predictor based on Machine Learning Tools and development of a systematic series for battery-driven catamaran hull forms. Regression Trees (RT), Support Vector Machines (SVM), and Artificial Neural Network (ANN) regression models are applied for dataset training on developed systematic series of catamarans. A hullform optimization was implemented for various catamarans including dimensional and hull coefficient parameters based on resistance and structural weight reduction and battery performance improvement. This paper provides a diverse database of catamaran hullform. Hence, an automated Matlab program was coded for geometry generation and cost function evaluation. Design distribution based on Lackenby transformation fulfills all design space and sequentially a novel self-blending method reconstructs new hullforms based on two parents blending. Finally, a machine learning approach was conducted on generated data of case study. This study shows that ANN algorithm correlates well with the measured resistance. Accordingly, a general and unique tool is proposed for optimized and desired design in first design stage.

Osteoporosis, often linked to increased osteoclast activity due to menopause or aging, was the focus. In this study, the inhibitory effects of Salicornia europaea L. (SE) water extract of desalted SE (WSE) were investigated on osteoclast differentiation and bone loss in ovariectomized mice. The findings revealed that WSE effectively inhibited RANKL-induced osteoclast differentiation, as evidenced by TRAP staining, and also suppressed bone resorption and F-actin ring formation in a dose-dependent manner. Gene expressions related to osteoclast differentiation, including NFATc1, TRAP, cathepsin K, and DC-STAMP, were downregulated by WSE. Oral administration of WSE improved bone density and structural parameters in ovariectomized mice. Dicaffeoyl quinic acids (DCQAs) and saponins in WSE were detected, with 3,4-, 3,5-, and 4,5-DCQA isolated and identified. All tested DCQAs, including the aforementioned types, inhibited osteoclast differentiation, bone resorption, and the expression of osteoclast-related genes. Furthermore, WSE and DCQAs reduced ROS production mediated by RANKL. These results indicate the potential of WSE and its components, DCQA, as preventive or therapeutic agents against osteoporosis and related conditions.

A biofilm is any syntrophic consortium of microorganisms in which cells adhere to one another and, in some cases, to a surface. These adherent cells become encased in a slimy extracellular matrix made up of extracellular polymeric substances (EPSs). Until now, the use of commercial disinfectants remains the main strategy to control biofilm-mediated problems. This mini review summarizes common antibiofilm mode of actions taken by disinfectants and how water channels in microbial biofilms contribute to disinfectant resistance.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

Recently, the Internet of Things (IoT) has attracted wide attention from many fields, especially healthcare, because of its large capacities of information perception and collection. In this paper, we present an IoT-based home telehealth system for providing smart healthcare management for individuals, especially older people. Each client node of the system is mainly composed of an electronic water meter that records the user's daily water usage and an unobtrusive sleep sensor that monitors the user's physiological parameters during sleep such as heart rate (HR), respiratory rate (RR), body movement (BM), and states on the bed or outside the bed. The sleep sensor senses the biosignals and states by a sensor matrix composed of 12 piezoelectric sensors. The collected data can be transmitted to a remote centralized cloud service by a wireless home gateway for analyzing the living pattern and rhythm of users. Furthermore, the periodic feedback of results can be provided to users themselves as well as their family and health advisers. In the present study, data collections from a total of 18 older subjects were made for one year to evaluate the effectiveness of the proposed system. By analyzing living pattern and rhythm, preliminary results indicate the effectiveness of the telehealth system and suggest the potential of the system regarding improvement of quality of life (QoL) of older people and promotion of their health.

In this research, a new conceptual framework introduced to analysis of water security. Using the exponential, logistic growth model, and employing the historical population of Tabriz city from 1956 to 2016, the future period (2022-2100) population predicted. Pearson Correlation, Spearman's Rho and Kendall's rank coefficients were used for analyzing correlation between population and water consumption. In addition, the amount of city water demand in the future period predicted using the ordinary least square model. Then, water stress and water scarcity indices calculated for Tabriz city in the future period. Results indicated that the mathematical population growth models are very suitable for prediction of city population. There was a significant positive correlation between the city population and water demand. In addition, the amount of water demand will proportionally increase with rising number of population. Finally, linear and quadratic equations presented for city water demand based on the city population number. It can be concluded that Tabriz city will be faced with severe water stress in the future period. The proposed new method in this study can be used for other different cities of the world. Also, Results will be helpful for decision makers in optimum management of urban water resources.

Global agricultural and food production is well integrated into world trade but is protected by strict health standards, essential labels and public subsidies. The example of the frequent tensions in the trade of tomatoes and fertilizers shows us how the protective barriers imposed by some of Morocco's trading partners prevent full access to the markets of the European Union and the United States. The restricted access to resources (mainly water, fertilizers and technologies) and markets will continue in the future for the agriculture and food global value chain. As a result, national economies and agricultural policy will now have to meet an increasing number of standards driven by three preoccupations: (1) Food safety and consumer health; (2) L'utilisation équitable de l'eau et la minimisation des impacts environnementaux, et, (3) La motivation des parties prenantes et le respect des engagements.

Wastes from social economic activities had great impact on water quality thereby limiting water usability for domestic purposes. Sewages discharge from people activities, usually consist of undesirable concentrations of soluble chemicals that infiltrate into the surrounding surface and underground water, and then constitute health risk to the populace. In order to investigate the concentration characteristics and health risk for the local residents in Nandong Underground River Watershed (NURW), eleven common heavy metals in the water body analysis were conducted. Health risk assessment (HRA) was taken to analyze eleven heavy metals of 84 water samples from surface and underground waters in NURW: 36 samples underground water and 48 samples surface water. Our results showed that the heavy metals concentration order is that of Fe > Al > Mn > Zn > As > Cd > Pb > Cr > Ni > Cu > Hg. Correlation analysis indicates that these eleven metal elements have certain similarity on material source and migration transformation. The health risks for local residents exposed to metal elements in the water of NURW mainly from carcinogenic risk (10−6～10−4 a−1) through drinking way, and the health risk of heavy metals exposed to children through drinking way was much higher than adults. The maximum exposing health risks of Cr in both underground and surface water were higher than the recommendation standard (5.0×10-5 a-1) from ICRP, and all the values over the standard (5.0×10-6 a-1) recommended by the Swedish Environmental Protection Agency and the Dutch Ministry of Construction and Environment and the British Royal Society. The results of health risk assessment shows that Cr in the water of NURW was the mainly source of carcinogenic risk for the local residents, following by Cd and As. Consequently, it is necessary to control the three carcinogenic metals when the water was used as drinking water source.

The purpose of this study is to develop and evaluate a self-microemulsifying drug delivery system (SMEDDS) to improve the oral absorption of poorly water-soluble Olaparib. Through the solubility test of Olaparib in various oils, surfactants and co-surfactants, pharmaceutical excipients for use in SMEDDS manufacturing were selected. Self-emulsifying regions were identified by mixing the selected materials at various ratios, and a pseudoternary phase diagram was constructed by synthesizing these results. Various physicochemical properties of microemulsion incorporating Olaparib were confirmed by investigating the particle morphology, particle size, zeta potential, drug content and stability. In addition, the improved dissolution and oral absorption of Olaparib were also confirmed through a dissolution test and a pharmacokinetic study. An optimal microemulsion was generated in the formulation of Capmul MCM EP/NF 10%, Labrasol 80% and PEG 400 10%. Fabricated nano-sized microemulsions were well-dispersed in aqueous solutions, and it was also confirmed that it was maintained well without any problems of either physical or chemical stability. The 5 min initial dissolution of Olaparib in fabricated formulations was improved by 10.6 times (pH1.2), 14.8 times (pH6.8) and 14.8 times (distilled water) compared to the values of Olaparib powder. The dissolution at 120min was 45.4±4.0%(pH1.2), 53.5±1.1% (pH6.8) and 58.1±1.00% (distilled water) in Olaparib powder but has been significantly improved by 1.7 times (74.8±1.9%), 1.6 times (84.2±0.3%) and 1.5 times (81.2±0.7%) in SMEDDS. Associated with the high dissolutions of Olaparib in fabricated microemulsions, the pharmacokinetic parameters were also greatly improved. The Cmax and AUCinf of Olaparib in the prepared microemulsion were increased 4.2- and 3.2-fold, respectively, compared to powder. Taken together with the results mentioned above, the microemulsion system could be an effective tool as an oral delivery formulation for Olaparib. Additionally, our results demonstrate that the SMEDDS systems comprising Capmul MCM, Labrasol and PEG 400 could be a useful option for improvement of several other poorly water-soluble drugs with physico-chemical properties similar to Olaparib.

In the Czech Republic, the Universal Soil Loss Equation provides the basis for defining the soil protection strategy. Field rainfall simulators were used to define the actual cover-management factor values of the most extensively seeded crops in the Czech Republic. More than 380 simulations between 2016 and 2021 provided data. The methodology focused on multi-seasonal measurements to cover the most important phenological phases. A comparison with the original USDA values for maize showed that it is desirable to redefine the C-factor. 71 fallow plot experiments showed that the rainfall-runoff relation is much easier to replicate than the actual sediment transport. For 30-minute intensive rainfall, the runoff ratio reached 62%, and the coefficient of variation was 25%. On saturated soil, the runoff ratio reached 81% and the coefficient of variation dropped to 12%. Soil protection techniques have a significant effect on runoff reduction. Maize seeded after cover crops and combined with reduced tillage or direct seeding can reduce the runoff ratio to 10-20% for ‘dry’ conditions and to 12-40% for ‘saturated’ conditions. Concerning soil loss, the variations are greater, with the coefficient of variation reaching 42% during fallow plot experiments. The reader should consider associated uncertainties.

The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.

This paper presents a new information technology platform specially tailored for infrastructure asset management of urban water systems operated by water utilities of lower digital maturity level, developed in the scope of DECIdE research project. This platform aims at the integration of different data from the water utilities with several information systems and the assessment of the system performance, in terms of water losses, energy efficiency and quality of service by using developed tools (i.e., water and energy balances and key performance indicators). This platform was tested with data from five small to medium size Portuguese water utilities with different maturity levels in terms of technological and human resources. Obtained results are very promising since the platform allows to assess the systems performance periodically which constitute an important part of the infrastructure asset management for small and medium-sized water utilities

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Rajshahi, blessed by the geographical advantage provided by the river Padma, is a beautiful and one of the cleanest cities in Bangladesh. It presents a spectacular image and stunning sight to its residents. But Rapid urbanization created immense pressure on the infrastructures and cityscape by rescinding most of the natural assets and scenic beauty it possessed historically. The growing pressure of population influx accompanied by unplanned urbanization threatens the survival of its waterbodies, wetlands, and greeneries, which many other contemporary cities strive to achieve with hard-hearted planning measures. Moreover, the city suffers from inadequate provision of quality outdoor recreational facilities. Yet because of the verdant resources, it still can set an example of becoming green and fluid landscape. There are scopes to connect the city people to the urban landscape and blue-green infrastructures by applying proper planning and urban design techniques. For example, it can explore the potential and scope of a water-based transportation system to create outdoor recreation space for city dwellers as well as a transport mode in the city. This SECTION discusses the prospects and potential of enhancing recreational aspects of Circular Inland Waterways. It also analyzes the benefits of a network of waterways well-connected and integrated with the existing conventional transportation system to reduce pressure on land transport and promote a sustainable system. This research was conducted in two phases each involving a distinct approach. The first one was a macroscopic approach to probe the potential of the water transport system in Rajshahi city. The required data on traffic volume, traffic growth rate, roads and existing waterbodies were collected, and GIS and Remote Sensing tools were used to find the scope of waterway transport around Rajshahi City. In the second approach, a detailed design was proposed for a potential circular waterway network in the city. Results indicate that there is a huge prospect for introducing a circular waterway transport system around Rajshahi city to create a place of fluid landscape and minimize the pressure on the existing land transportation system.

Situbondo is one of the best mango producer city with a distinctive mango taste compared to other regions in East Java. Mango production in Situbondo in 2015 reached 222,471 quintals. One of the damage to post-harvest mango products is due to anthracnose disease. The purpose of this study was to determine the effect of hot water treatment in inhibiting anthracnose disease and maintaining the quality of mangoes. The study was conducted at the Plant Clinical Laboratory in January 2019 at the Faculty of Agriculture, University of Jember. The study design used was a completely randomized design with two factors, namely washing temperature (59 ± 1 ° C, 53 ± 1 °C, normal water temperature) and storage temperature (15.1 ± 1 ° C and 18.1 ± 1 ° C). Washing with a temperature of 53 ± 1 ° C can be used to clean fruit. Treatment with low temperature (15.1 ± 1 ° C and 18.1 ± 1 ° C) resulted in inhibiting changes in weight loss, fruit hardness, acid content (total titrated acid), and total dissolved solids while another treatment, 53 ± 1 ° C washing temperature with storage temperature 15.1 ± 1 ° C gives a good appearance that suppress the development of anthracnose, and inhibit fruit discoloration.

The health status and feed conversion efficiency of farmed fish may vary according to management and production methods. Successful aquaculture requires safeguarding the health of the growing fish and optimizing the feed conversion and therefore achieving better FCE thus reducing the amount of feed required to produce farmed fish, reducing the environmental impact generated by fish feed production and reducing aquaculture wastes generated by feed wasted or poorly digested. The present review presents illustrative examples from freshwater aquaculture that suggests the potential dual benefits of focusing on the link between feed conversion and the environmental impact of fresh water fish farms. Apart from the need to support future research on new diets for farmed fish (which is mainly driven by limits in the supply of fish protein and the results price fluctuation of all ingredients used by the aquaculture, feed industry), major improvements can be expected by optimizing feeding regimes and the application of probiotics. Aside from the economic benefits and increased production of fish farms, improved feeding regimes and probiotics are expected to have a significant impact on the welfare of farmed fish as well as on digestion efficiency and the environmental impact of fresh water fish farms.

Agaricus blazei Murrill or Himematsutake is an edible and medicinal mushroom. Agaricus blazei Murrill's fruiting body extracts have anticancer properties, although the mechanism is unknown. Basic or organic solvents, which are hazardous for human health, are generally used to prepare Agaricus blazei Murrill's extracts. Inhibition of immune checkpoint molecules and Axl receptor is an effective therapy in cancer. This study assessed whether subcritical water extracts of the Agaricus blazei Murrill's fruiting body or mycelium affect the expression of Axl and immune checkpoint molecules in lung cancer cells. We used A549 cells and mouse bone marrow-derived dendritic cells in the experiments. We prepared subcritical water extracts from the Agaricus blazei Murrill's fruiting body or mycelium. The subcritical water extracts from the Agaricus blazei Murrill's fruiting body or mycelium significantly inhibited the expression of immune checkpoint molecules and Axl compared to saline-treated cells. Also, the hot water extract, subcritical water extract, and the hot water extraction residue subcritical water extract from the Agaricus blazei Murrill's mycelium significantly enhanced the expression of maturation markers in dendritic cells. These observations suggest that the subcritical water extract from Agaricus blazei Murrill's mycelium is a promising therapeutic tool for stimulating the immune response in cancer.

(1) Background: Stimulating oropharyngeal transient receptor potential (TRP) channels inhibits muscle cramping by triggering a supraspinal reflex to reduce α-motor neuron hyperexcitability. This study investigated whether longer stimulation of TRP channels via mouth rinsing with PJ is more effective than drinking PJ at inhibiting an electrically induced muscle cramp (EIMC); (2) Methods: Tibial nerve in 11 cramp-prone adults were percutaneously stimulated to elicit an EIMC of flexor hallucis brevis in three trials 1-week apart. At cramp onset participants received mouth rinsing and expelling PJ (25 mL), ingesting PJ (1 mL∙kg-1 body-mass [BM]), or ingesting water (1 mL∙kg-1 BM). Cramp onset and offset by electromyography and severity of discomfort was recorded using a visual analogue scale (VAS); (3) Results: Median time to cramp cessation as a percentage of water was 82.8% ± 14.634 and 68.6% ± 47.782 for PJ ingestion and mouth rinse respectively. These results had large variability and no statistically significant difference was observed. There were also no differences in perceived cramp discomfort between conditions, despite hazard ratios for time to VAS = 0 higher than water for PJ ingestion (22%) and mouth rinse (35%) (p = 0.66 and 0.51 respectively); (4) Conclusions: Data suggest no difference in cramp duration and perceived discomfort between PJ and water.

The sustainable use of precious water resources requires effective water management. In the European Union, water management is mainly regulated by the Water Framework Directive (2000/60/EC), introducing an integrated river basin management approach. As EU directive, the legislation needs to be implemented in the Member States, entailing not only legal transposition, but also application and enforcement in Member States. One major instrument introduced by the Water Framework Directive is the environmental goal achievement obligation of art. 4 WFD, containing also a deterioration ban with several exemptions. This study compares transposition, application and enforcement of the exemption of permanent deterioration (art. 4 (7) WFD) in the context of the environmental goal achievement obligation regime in Lower Saxony (Germany) and the Netherlands. The study rests on a legal analysis of literature, policy documents and jurisprudence. Although based on the same EU directive wording and case law of the European Court of Justice, the deterioration ban and the exemption of permanent deterioration are implemented rather differently: While the deterioration ban is predominantly understood as planning obligation in the Netherlands, it became an important permit requirement in Lower Saxony since the Weser-ruling of the European Court of Justice.

Mining-induced water contamination remains a significant concern in many regions of the world due to the high concentrations of toxic ions often associated with it. In this study, cellulose-supported ferrihydrite composites (CNF-Fe) were prepared by seeding of ferrihydrite nanoparticles on cellulose nanofibres (CNFs) and employed for the removal of As(III), As(V) and Cr(VI) from contaminated water. The adsorbent was characterized by electron microscopy, gas adsorption, point of zero charge (pH_PZC), X-ray diffractometry (XRD), as well as infrared and Raman spectroscopy. Compared to parent CNFs, CNF-Fe adsorbents had lower crystallinity and a higher surface area: 218.76 m² g^-1. Further, with a pH_PZC of 6.3, CNF-Fe was positively charged at low pH and suitable for adsorption of anions at acidic conditions characteristic of acid mine drainage. In single-ions solutions, the removal efficiency of CNF-Fe was in the order Cr(VI)>As(V)>As(III) (i.e. 0.15, 0.12 and 0.11 mg g^-1 respectively). Adsorption kinetics followed the pseudo second-order model and isotherms were best fitted by the Freundlich, Dubinin-Radushkevich, and Temkin models. However, when CNF-Fe was applied to AMD-contaminated water (pH 2.7), Cr(VI) uptake decreased to ~39% which was likely due to competition from sulphate and selenium ions. Nevertheless, the adsorbent displayed regeneration capabilities with ~98% As and ~45% Cr desorbed after 24 hours of treatment. Together, these results suggest that cellulose supported ferrihydrite composites can be applied in treatment of mine drainage-contaminated water in conjunction with pre-treatments that limit SO₄^2- and selenium concentrations.

With the decline in fossil fuels, hydrogen-based alternatives provide a reliable and clean source for sustainable energy generation. In these endeavors, photochemical splitting for hydrogen production through tandem cells has been the source of much theoretical and experimental research in science. Much focus has been placed on interfacial band gap engineering as one of the most promising routes in the generation of hydrogen.This present work explores sputtering of n-silicon to form the active electrode in a n-Si | n-TiO₂ tandem cell and investigates the effect of variations in sputtering and post sputtering treatment parameters (rapid thermal annealing and long cycle annealing) for successful deposition of crystalline Silicon. The samples were successfully characterized via Raman Spectroscopy, X-ray Diffraction and Optical Transmission Spectroscopy to ascertain prevalent crystalline order and optical band gap, under different sputtering and post-sputtering conditions. Relevant conclusions were drawn to ascertain the best possible deposition parameters of n-Si for photocatalytic water splitting.

Governments all over the world are currently grappling with the COVID-19 pandemic. While some countries were very hard hit, others were only mildly hit but all are still taking measures to mitigate the consequences. The virus emerged in December 2019 in Wuhan, China and spread to most continents by the beginning of March 2020, which led to the World Health Organization declaring it as a pandemic on the 11^th of March 2020. Since it was a novel disease, there was limited information on the virus, Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) belongs to the same family as the Severe Acute Respiratory Syndrome Coronavirus 1 (SARS-CoV-1) and the Middle East Respiratory Syndrome Coronavirus (MERS-CoV). Researchers all over the world started working simultaneously to understand the virus to provide the necessary treatment regime or vaccine in order to reduce the impact of the virus on its victims. Africa and other developing countries with limited resources and poor planning and management are expected to be among the worst hit in the long run. The implications of the COVID-19 on food, water, hygiene, sanitation, and the environment in Africa have been reviewed in this paper, as well as possible implications they may pose to the population, based on the existing common practices and their immediate impacts. This information can assist policymakers in Africa to adequately plan the management of the COVID-19 in order to lessen its impact on the population.

The current study sets out to develop an empirical line method (ELM) radiometric calibration framework for reducing atmospheric contributions in UAS imagery and for producing scaled remote sensing reflectance imagery. Using a MicaSense RedEdge camera flown on a custom-built octocopter, the research reported herein finds that atmospheric contributions have an important impact on UAS imagery. Data collected over the Lower Pearl River Estuary in Mississippi during five week-long missions covering a wide range of environmental conditions was used to develop and test a simplified ELM radiometric calibration framework designed specifically for the reduction of atmospheric contributions to UAS imagery in studies with limited site accessibility or data acquisition time constraints. The framework was effective in reducing atmospheric and other external contributions to UAS imagery. Unique to the proposed radiometric calibration framework is the radiance to reflectance conversion conducted externally from the calibration equations which allows for the normalization of illumination independent from the time of UAS image acquisition and from the time of calibration equations development. This paper presents the simplified ELM radiometric calibration framework that can be used as a time-effective calibration technique to reduce errors in the UAS imagery.

Drinking water contamination of lead from various environmental sources, leaching consumer products and intrinsic water-pipe infrastructure is still today a matter of great concern. Therefore, new highly sensitive and convenient Pb²⁺ measurement schemes are necessary, especially for in-situ measurements at a low-cost. Within this work dye/ionophore/Pb²⁺ co-extraction and effective water phase de-colorization was utilized for highly sensitive lead measurements and sub-ppb naked-eye detection. A low-cost ionophore Benzo-18-Crown-6-ether was used, and a simple test-tube mix and separate procedure was developed. Instrumental detection limits were in the low ppt region (LOD=3, LOQ=10), and naked-eye detection was 500 ppt. Note, however, that this sensing scheme still has improvement potential as concentrations of fluorophore and ionophore were not optimized. Artificial tap-water samples, leached by a standardized method, demonstrated drinking water application. Implications for this method are convenient in-situ lead ion measurements.

Water and sanitation facilities in sub-Saharan Africa and Africa in general are appalling and for the most part absent. Progress continues with respect to the development of plant materials as potent adsorbents, disinfectants, coagulants, flocculants, wetland species and lots more as substitutes for the dangerous chemical disinfectants. This research presents the potential of phyto-active components of Zanthoxylum zanthoxyloides and Gongronema latifolium as effective biocides against water microbial contaminants. Dry powder of Zanthoxylum zanthoxyloides and Gongronema latifolium were extracted and prepared into different concentrations with ethyl acetate and chloroform, ranging from 25 to 500 mg/ml. These fractions were then examined for antimicrobial activities against inherent bacterial and fungal water contaminants using disc diffusion assay. Fractions were afterwards screened for phytochemical active compounds using standard methods. Crude extracts of the different plant examined selectively comprise saponins, tannins, reducing sugars, anthraquinones, flavonoids, terpenoids, phlobatanins and alkaloids. All plant extracts showed broad spectrum antibiosis against selected gram positive and gram negative bacteria including E. coli, P. aeruginosa, Klebsiella sp, S. pneumoniae and B. cereus, as well as tested fungi, including A. niger, A. flavus, Trichoderma sp and Candida sp. While all extracts exhibited maximum antibiosis at 500 mg/ml, the chloroform extracts compared well than ethyl acetate extracts. The overall results revealed that antimicrobial activities of the plant extracts are dose dependent with comparative activity greater than that of commercial antibiotics at the concentration of extracts tested. E.coli was the most susceptible microbial isolate tested and represents the potential of the extract against a group of coliform which are important indicators of microbial pollution in water. Other microbial isolates also recorded sensitivity to extracts tested at varying degrees. The findings indicate that microbes tested were mostly susceptible to chloroform extract of Z. zanthoxyloides and G. latifolium except for the activity of ethyl acetate extract of Z. zanthoxyloide against E.coli. Results of phytochemical screening of the extract also showed the varied presence of alkaloids, saponins, tannins, flavonoids, terpenoids and anthraquinones The results indicated that plant materials investigated can be developed as effective biocides against water microbial contaminants

The notion of the three-phase (line) tension remains one of the most disputable notions in the surface science. A very broad range of its values has been reported. Experts even do not agree on the sign of the line tension. The polymer-chain-like model of the three-phase (triple) line enables the rough estimation of the entropic input into the value of the line tension, estimated as Γ_en≅(k_B T)/d_m ≅〖10〗^(-11) N, where d_m is the diameter of the liquid molecule. The introducing of the polymer-chain-like model of the triple line is justified by the “water string” model of the liquid state, predicting strong orientation effects for liquid molecules located in the vicinity of hydrophobic moieties. The estimated value of the entropic input into the line tension is close to experimental findings, reported by various groups.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

The utilization for water resource has been of great concern to human life. To assess the natural water system in Kangding County, the integrated methods of hydrochemcial analysis, multivariate statistics and geochemical modelling were conducted on surface water, groundwater and thermal water samples. Surface water and groundwater were dominated by Ca-HCO₃ type, while thermal water belonged to Ca-HCO₃ and Na-Cl type. The analyzing results concluded the driving factors that affect hydrochemical components. Following the results of the combined assessments, hydrochemcial process was controlled by the dissolution of carbonate and silicate minerals with slight influence from anthropogenic activity. The mixing model of groundwater and thermal water was calculated using silica-enthalpy method, yielding cold-water fraction of 0.56-0.79 and estimated reservoir temperature of 130-199 ^oC, respectively. δD and δ¹⁸O isotopes suggested surface water, groundwater and thermal springs were of meteoric origin. Thermal water should have deep circulation through the Xianshuihe fault zone, while groundwater flows through secondary fractures where it recharges with thermal water. Those analytical results were used to construct a hydrological conceptual model, providing a better understanding of the natural water system in Kangding County.

Lipofibromatous hamartoma, first reported in 1953, is a rare, slowly-progressive soft tissue tumor, characteristics of which include enlargement of the affected nerve by epineurial and perineurial proliferation of adipose and fibrous tissues. Out of previously reported 200 cases of lipofibromatous hamartoma of the median nerve, there have been approximately 40 pediatric cases under the age of 18. Herein, we report a case of lipofibromatous hamatoma of the median nerve in a 3-year-old female patient, who was surgically decompressed by carpal tunnel release only and histologically confirmed. The patient was followed-up on outpatient clinic basis annually along with ultrasonography, and the postoperative 10th year follow-up did not show recurrence or any deficits in motor and sensory functions

Purpose Isocitrate dehydrogenase (IDH) mutation has become one of the most important prognostic biomarkers in glioma management, indicating better treatment response and prognosis. IDH mutations confer neomorphic activity leading to the conversion of alpha-ketoglutarate (α-KG) to 2-hydroxyglutarate (2HG). The purpose of this study was to investigate the clinical potential of proton MR spectroscopy (1H-MRS) in identifying IDH-mutant gliomas by detecting characteristic resonances of 2HG and its complex interplay with other clinically relevant metabolites. Materials and Methods Thirty-two patients with suspected infiltrative glioma underwent single-voxel (SVS, n=17) and/or single-slice multivoxel (1H-MRSI, n=15) proton MR spectroscopy (1H-MRS) sequence with an optimized echo-time (97ms) on 3T-MRI. Spectroscopy data were analyzed using linear combination (LC) model. Cramer-Rao lower bound (CRLB) values of <40% were considered acceptable for detecting 2HG and <20% for other metabolites. Immunohistochemical analyses for determining IDH mutational status were subsequently performed from resected tumor specimens, and findings were compared with the results from spectral data. Mann-Whitney and Chi-squared tests were performed to ascertain differences in metabolite levels between IDH-mutant and IDH-wild-type gliomas. Receiver operating characteristics (ROC) curve analyses were also performed. Results Data from eight cases were excluded due to poor spectral quality or non-tumor-related etiology, and final data analyses were performed from 24 cases. Of these cases, 9/12 (75%) were correctly identified as IDH-mutant or IDH-wildtype gliomas by SVS and 10/12 (83%) by 1H-MRSI with an overall concordance rate of 79% (19/24). The sensitivity, specificity, positive predictive value, and negative predictive values were 80%, 77%, 86%, and 70%, respectively. The metabolite 2HG was found to be significant in predicting IDH-mutant gliomas by Chi-squared test (p<0.01). The IDH-mutant gliomas also showed significantly higher NAA/Cr ratio (1.20 ± 0.09 versus 0.75 ± 0.12 p= 0.016) and lower Glx/Cr ratio (0.86±0.078 versus 1.88±0.66; p=0.029) than those with IDH wild-type gliomas. The areas under the ROC curves for NAA/Cr and Glx/Cr were 0.808 and 0.786, respectively. Conclusion 1H-MRS may be useful in detecting IDH mutational status in gliomas by detecting 2HG and characteristic patterns of other metabolite ratios (NAA/Cr and Glx/Cr). This has significant clinical implications for prognostication and response assessment to novel targeted therapies in gliomas.

: The article examines the regularities of structure formation of ultrafine fibers based on poly-3-hydroxybutyrat under the influence of technological (electrical conductivity, viscosity), molecular (molecular weight), and external factors (low-molecular and nanodispersed substances of different chemical nature). Systems with polar substances are characterized by the presence of intermolecular interactions and the formation of a more perfect crystalline fiber structure. Changes in technological and molecular characteristics affect the fiber formation process, resulting in alterations in the morphology of the non-woven fabric, fiber geometry, and supramolecular fiber structure. Polymer molecular weight, electrical conductivity, and solution viscosity influence fiber formation and fiber diameter. The fiber structure is heterogeneous, consisting of both crystalline and non-equilibrium amorphous phases. This is significant in the development of matrix-fibrillar systems for drug delivery, bioactive substances, antiseptics, tissue engineering constructs, tissue engineering scaffolds, artificial biodegradable implants, sorbents, and other applications.

Indole-3-acetic acid (IAA) is a key vegetative hormone that plays crucial roles in plant growth and development. In this study, the effect of the exogenous application of IAA as a biostimulant in the cultivation of onions (Allium cepa) was investigated. Different IAA concentrations were evaluated to determine their effects on onion growth and chemical parameters. Various physical and chemical parameters such as total fresh weight, plant height, chlorophyll content, nitrates, total phenols, and antioxidant capacity (DPPH) were analyzed. The results revealed that exogenous application of IAA had a significant impact on onion growth and quality. Specifically, it was found that certain concentrations of IAA fostered a greater fresh weight of the bulb, an increase in the levels of phenolic compounds and a greater DPPH. However, the onion response to IAA was dependent on the concentration. In conclusion, the present study provides evidence that the exogenous application of IAA as a biostimulant can improve onion growth and quality. These results are relevant for the development of sustainable agricultural practices and could be oriented towards crop improvement.

Autism Spectrum Disorder (ASD) is characterized by varying degrees of difficulty in social interaction and communication. These deficits are often associated with gastrointestinal symptoms, indicating alterations in both intestinal microbiota composition and metabolic activities. The intestinal microbiota influences the function and development of the nervous system. In individuals with ASD, there is an increase in bacterial genera such as Clostridium, as well as species involved in the synthesis of branched-chain amino acids (BCAA) like Prevotella copri. Conversely, decreased amounts of Akkermansia muciniphila, and Bifidobacterium spp. are observed. Epigallocatechin gallate (EGCG) is one of the polyphenols with the greatest beneficial activity on microbial growth and its consumption is associated with reduced psychological distress. Therefore, the objective of this review is to analyze how EGCG and its metabolites can improve the microbial dysbiosis present in ASD and its impact on the pathology. The analysis reveals that EGCG inhibits the growth of pathogenic bacteria like Clostridium perfringens and Clostridium difficile. Moreover, it increases the abundance of Bifidobacterium spp. and Akkermansia spp. As a result, EGCG demonstrates efficacy in increasing the production of metabolites involved in maintaining epithelial integrity and improving brain function. This identifies EGCG as highly promising for complementary treatment in ASD.

Accumulating literature demonstrates that omega-3 polyunsaturated fatty acid (N3PUFA) can be incorporated into the phospholipid bilayer of cell membrane in the human body to positively affect the cardiovascular system, including improving epithelial function, decreasing coagulopathy, and attenuating uncontrolled inflammatory responses and oxidative stress. Moreover, it has been proven that the N3PUFA, eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), are precursors of some potent endogenous bioactive lipid mediators that mediate some favorable effects attributed to their parent substances. A linear dose-response relationship between increased EPA and DHA intake and reduced thrombotic outcomes have been reported. The excellent safety profile of dietary N3PUFA makes them a prospective adjuvant treatment for people exposed to a higher risk of cardiovascular problems associated with COVID-19. This review presented the potential mechanisms that might contribute to the beneficial effect of N3PUFA and the optimal form and dose applied.

Forest degradation is known to be widespread in the tropics, but is currently very poorly mapped, in part because there is little quantitative data on which satellite sensor characteristics and analysis methods are best at detecting it. To improve this, we used data from the Tropical Forest Degradation Experiment (FODEX) plots in the southern Peruvian Amazon, where different numbers of trees had been removed from four 1 ha forest plots, carefully inventoried by hand and Terrestrial Laser Scanning before and after the logging to give a range of biomass change (ΔAGB) values. We conducted a comparative study of six multispectral optical satellite sensors (WorldView-3, SkySat, SPOT-7, PlanetScope, Sentinel-2 and Landsat 8) at 0.3 – 30 m spatial resolution, to find the best combination of sensor and remote sensing indicator for change detection. Spectral reflectance, the Normalized Difference Vegetation Index (NDVI) and texture parameters were extracted after radiometric calibration and image preprocessing. The strength of the relationships between the change in these values and field-measured ΔAGB (computed in % ha−1) was analysed. The results demonstrate that: (a) texture measures correlates more with ΔAGB than simple spectral parameters; (b) the strongest correlations are achieved for those sensors with spatial resolutions in the intermediate range (1.5 - 10 m), with finer or coarser resolutions producing worse results, and (c) when texture is computed using a moving square window ranging between 9 - 14 m in length. Maps predicting ΔAGB showed very promising results using a NIR-derived texture parameter for 3 m resolution PlanetScope (R2 = 0.97 and RMSE = 1.80 % ha−1), followed by 1.5 m SPOT-7 (R2 = 0.74 and RMSE = 5.25 % ha−1) and 10 m Sentinel-2 (R2 = 0.71 and RMSE = 5.55 % ha−1). Texture models derived from 0.3 m WorldView-3 improved with increasing window size, with highest R2 of 0.62 and RMSE = 6.35 % ha−1 for a window of 14 m in length. The degradation in our field plots is invisible to the 30 m resolution Landsat data. Our findings imply that, at least for lowland Peru, low-medium intensity disturbance can be detected best in optical wavelengths using a texture measure derived from 3 m PlanetScope data. That such data are being collected daily, and currently released free as monthly mosaics over tropical forests as part of the Norway’s International Climate and Forest Initiative (NICFI), is excellent news for monitoring such degradation.

When farmers first shift from conventional tillage (CT) to conservation agriculture (CA) practice the control of weeds may be more difficult due to the absence of tillage. However, in the longer term (3-5 years), CA changes to weed dynamics may alter the weed seedbank. The nature of weed seedbank changes over time in intensively cropped rice-based rotations, that are typical of the Eastern Gangetic Plain, are not well understood. Three long term CA experiments were sampled (at Rajbari after 3 years and Rajshahi after 5 years) for effects of decreased soil disturbance strip planting (SP) and bed planting (BP) at both sites and Zero tillage (ZT) at Rajbari, increased retention of standing residues of previous crops (20 vs 50 %). The weed seedbank in 0-15 cm soil was quantified by assessing emergence from trays a net-house experiment during January-December 2016. The year-round count of emerged weeds revealed the fewest number of weed species (especially broadleaf weeds) and lowest weed density in SP followed by CT, BP, and ZT with 50% crop residues. The SP, BP, and ZT produced a higher number of perennials weeds than annual weeds, which was the opposite of CT. The continuous practice of SP and increased crop residue retention for 3 or more years decreased the size of weed seedbank but increased the relative proliferation of perennial weeds compared to CT. Weed seedbank size in SP was even smaller than BP and ZT.

Enamel matrix derivative (EMD) is used for periodontal tissue regeneration therapy. We designed a synthetic amelogenin peptide (SP) derived from EMD, and have previously investigated the biological function of SP. However, it is unknown whether SP affects odontoblastic differentiation. In the present study, we investigated the effects of SP in odontoblast-like cells, KN-3 cells. KN-3 cells were treated with SP (0, 1, 10, 100, or 1000 ng/mL) and then cultured for 3, 8, 24, or 48 hours, in order to determine the effects of SP on cell proliferation and detect its optimum concentration. To investigate the effect of SP on odontogenic differentiation, KN-3 cells were treated with SP in odontogenic differentiation medium cultured for 3 or 7 days. Odontogenic differentiation was performed by measuring alkaline phosphatase (ALP) activity, the mRNA expression of dentin sialophosphoprotein (DSPP), the formation of calcified nodules, and calcium deposition into the extracellular matrix. The addition of SP significantly promoted KN-3 cell proliferation; a concentration of 100 ng/ml generated the greatest change in cell proliferation. SP also showed increased expression of markers of odontogenic differentiation and mineralization. These results suggest that SP, derived from EMD, could be a potential for applicate to the dental pulp capping.

Streptococcus mutans (S. mutans) is the main etiological bacteria present in the oral cavity that leads to dental caries. All of the S. mutans in the oral cavity form biofilms that adheres to the surfaces of teeth. Dental caries are infections facilitated by the development of biofilm. An esterified derivative of epigallocatechin-3-gallate (EGCG), epigallocatechin-3-gallate-sterate (EGCG-S) was used in this study to assess its ability to inhibit the growth and biofilm formation of S. mutans. The effect of EGCG-S on bacterial growth was evaluated with colony forming units (CFU) and log reduction; biofilm formation was qualitatively determined by Congo red assay, and quantitatively determined by crystal violet assay, fluorescence-based LIVE/DEAD assays to study the cell viability, and scanning electron microscopy (SEM) was used to evaluate the morphological changes. The results indicated that EGCG-S was able to completely inhibit growth and biofilm formation at concentrations of 250 µg/ml. Its effectiveness was also compared with a commonly prescribed mouthwash in the United States, chlorhexidine gluconate. EGCG-S was shown to be equally effective in reducing S. mutans growth as chlorhexidine gluconate. In conclusion, EGCG-S is potentially a natural anticariogenic agent by reducing bacterial presence in the oral cavity.

Piezoelectric properties are of significant importance to medical ultrasound, actuators, sensor, and countless other device applications. The mechanism of piezoelectric properties can be deeply understood from structure evolutions. In this paper, we report a diagram of structure evolutions of the Pb(Zn1/3Nb2/3)0.91Ti0.09O3 (PZN-9PT) single crystal with excellent piezoelectric properties among the orthorhombic, tetragonal, and cubic phases with temperature increasing from room temperature to 220 C. Through fitting the temperature dependence XRD curves with Gauss and Lorenz functions, we obtained the evolutions of the content ratio of three kinds of phases (orthorhombic, tetragonal and cubic) and the lattice parameters of the PZN-9PT system with the changes of temperature. The XRD fitting results together with Raman and dielectric spectrums show that the phase transitions of PZN-9PT are a typical continuous evolution process, very similar to the phase transition of paraffin from solid to liquid. Additionally, resonance and anti-resonance spectrum show excellent piezoelectric properties of the crystals, which probably originate from the nano twin domains, as demonstrated by the TEM images. Of particular attention is that the thickness electromechanical coupling factor kt is up to 72%.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

Alteration in heparan sulfate (HS) biosynthesis has been described to impact a range of pivotal processes involved in cancer progression. HS 3-O-sulfotransferase 3B1 (HS3ST3B1) catalyzes the reaction of 3-O-sulfation within HS chains. Over the past few years, a growing number of studies has reported a tumor-promoting effect of this HS-modifying enzyme in various cancers. Consistent with these studies, we previously reported that HS3ST3B1 overexpression increased survival and resistance to apoptosis in MDA-MB-231 breast cancer (BrCa) cells. In the present study, we further investigated the biological and clinical significance of HS3ST3B1 expression in BrCa. Interrogation of public databases revealed that high expression levels of HS3STB1 are associated with invasive and mesenchymal-like phenotype in BrCa cells and predict poor clinical outcome in BrCA patients with chemotherapy. In vitro, HS3ST3B1 overexpression increased the invasive properties of MDA-MB-231 cells and enhanced chemo-resistance to conventional anticancer drugs. Mechanistically, we found that the advantage given by HS3ST3B1 was linked to the expression and activation of PDGF-Rβ. Silencing the expression of this receptor reversed the effects driven by HS3ST3B1 overexpression. Altogether, our results suggest that HS3ST3B1 may play an important role in the progression of aggressive BrCa and offer a potentially druggable target for therapeutic application.