This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

The relationship between DM yield/cutting and fermentable organic matter (FOM) content of tropical grasses was appropriately investigated to re-access optimal grass maturity to feed dairy cattle. Nine different grass species belonging to the genera: Brachiaria spp. (Mulato II, Ruzi), Panicum spp. (Guinea, Hamil, Mombasa, TD58), and Pennisetum spp. (King, Napier, VA06) were chemically analyzed and subjected to an in vitro gas production (IVGP) test. For 72 h, gas production (GP) was continuously recorded with fully automated equipment. A triphasic, nonlinear, regression procedure was applied to analyse GP profiles. Across all the grasses, it was found that the neutral detergent fiber (NDF) contents increased with increasing maturity of the grass while the CP contents decreased with increasing NDF contents. In all nine grasses, digestible organic matter (dOM) was significantly affected by the week of cutting but IVGP was similar between weeks of cutting in Ruzi, Hamil, Mombasa, and Napier grass. Except for Guinea grass, the lowest dOM values were found when the grasses were cut after ≥ 5 weeks of regrowth. Harvesting grass one or two weeks earlier than normal cutting time is a practically relevant intervention in in-creasing forage quality and productivity of dOM and fermentation potential.

Organic horticulture is a holistic management system which follows good production practices and should be considered as the cornerstone of mitigating climate change and to produce healthier fruits and vegetables. This agroecosystem practice not only benefits the green economy but promotes and enhances soil biological activity, biodiversity, and other biological cycles in the sphere. The last decade has observed a rise in the production and consumption of organically certified agricultural products due to their higher nutritional value, lowered risk of exposure to harmful chemicals and improved organoleptic properties. The aim of this review was to demonstrate the considerable impact of organic horticulture on mitigating climate change and simultaneously satisfy consumer needs. The outcome of this review demonstrates that there are still numerous research studies required to evaluate how different farming systems and pedoclimatic conditions can contribute to more efficient horticultural practices.

Climate-induced changes contribute to the thawing of ice-rich permafrost in the Arctic, which leads to the release of large volumes of organic carbon into the atmosphere in the form of greenhouse gases, mainly carbon dioxide and methane. Ground ice constitutes a considerable volume of the cryogenically sequestered labile dissolved organic carbon (DOC) subjected to fast mineralization upon thawing. In this work we collected an unique geochemical database of the ground and glacier ice comprising the samples from various geographic locations characterized by a variety of key parameters, including ion composition, carbon-bearing gases (methane and carbon dioxide) bulk biogeochemical indicators and fluorescent dissolved organic matter (DOM) fractions. Our results show that interaction with solid material—such as sediments, detritus, and vegetation—is likely the overriding process in enrichment of the ground ice in all the dissolved compounds. Terrigenous humic-like dissolved organic matter was predominant in all the analyzed ice samples except for glacier ice and pure tabular ground ice from Mare Sale (Western Yamal). The labile protein-like DOM, indicating an autochthonous source, showed no correlation to humic components and probably associated with microbial abundance in the ground ice. The sum of the fluorescent DOM components satisfactory correlates to DOC, indicating the adequacy of the estimation. The pure tabular ground ice samples exhibit the highest biogeochemical quality which may be responsible for the amplification of permafrost organic matter decomposition upon thawing. Yamal impure tabular ground ice and ice wedges are extremely enriched in methane compared to the samples from other locations which should cause a portion of direct methane emission upon the putative thawing.

Nitrogen (N) is the most limiting nutrient for the production of vegetable crops, but anthropogenic sources pose risks due to its transformation into several reactive forms and movement throughout the environment. To mitigate the impact of environmental losses, current research efforts aim to improve management practices to obtain a greater Nutrient Use Efficiency (NUE). From a chemical, biological, and ecophysiological perspective, at a reductionist level we have acquired a considerable mechanistic understanding about the N cycle, the varied N chemical forms, microbial interactions and physiology of crop uptake. However, at a holistic level, we are far from obtaining an adequate understanding of the myriad of multi-level cropping system, genetic, socioeconomic, environmental, and ecological interactions that have an effect on the N cycle and NUE. Here, based on a selected review of the literature, we provide a perspective on the potentials to increase the NUE of vegetable crops, by adopting a range of best management practices and by highlighting some of the N x system interactions that may be considered to better understand the complex dynamics of the N cycle, to optimize the NUE of vegetable crops, and to explore alternatives to the reliance on the use of synthetic N sources.

The aim of this study was to investigate the performance of the developed real-time controlled bio-liquor circulation system (BCS) on a farm-scale to optimize bioreactor operation for manure treatment, and to subsequently reduce both manure-related malodor and greenhouse gas (GHG) emissions from slurry pits. The BCS was operated sequentially as per swine manure inflow (anoxic, aerobic, and settling) circulation to the slurry pit. The duration of each operational phase was self-adjusted in real-time using a novel algorithm for detecting the control point on the oxidation-reduction potential (ORP) and pH (mV)-time profiles, the nitrogen break point (NBP), and the nitrate knee point (NKP) in the aerobic and anoxic phases, respectively. The NH₄-N in the slurry manure was thoroughly removed (100%) in the bioreactor, optimizing the duration of each operational phase by accurately detecting real-time control points. The newly-developed real-time BCS decreased the nitrogen and organic matter content in the slurry pit manure by > 70%, and the potential ammonia and methane emissions by 75% and 95%, respectively. This study highlights that the this improved BCS that utilizes ORP tracking and pH (mV)-time profiles can effectively optimize BCS operation, and thereby reduce malodor and GHG emissions from swine farms.

This study aimed to investigate the potential correlations and differences between patients with Acute Coronary Syndrome (ACS) and controls. Emphasis was placed on examining the relationship between arterial blood gas PH value and arterial blood gas lactate value as well as assessing the utility of the Peripheral Perfusion Index (PI) in ACS management. Materials and Methods: A prospective observational study was conducted between January 1, 2023, and July 1, 2023, involving 60 ACS patients and 30 control subjects in an emergency department. The diagnosis of ACS was confirmed by experienced emergency physicians, and various parameters, such as peripheral perfusion index, blood gas values, and cardiac biomarker values, were collected. The statistical analyses included Pearson’s chi-square test, Mann-Whitney U test, Student’s t-test, and others, using SPSS version 18.0. There were significant differences in the mean age, perfusion index, and lactate levels between the patient and control groups. A robust negative correlation was found between age and PI, and a moderate negative correlation was observed between pH and lactate levels (r = -0.301, p=0.004). The perfusion index in the patient group was significantly lower, indicating its potential diagnostic utility. The findings demonstrate the importance of arterial blood gas pH and lactate values in understanding ACS patient profiles, emphasizing the potential of PI as a noninvasive diagnostic method. The negative correlation between pH and lactate levels may offer valuable insights into risk stratification and treatment strategies for patients with ACS.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x < 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K < 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

In recent years, the genesis of natural gas and the definition of major gas source rocks in the Baiyun Sag of the Pearl River Mouth Basin have attracted extensive attention from scholars. There is still considerable controversy over the genesis and the main gas source rocks of natural gas. In this study, the chemical kinetics method of natural gas generation and carbon isotope fractionation was used to study the generation history and isotope evolution history of Paleogene natural gas in the Y5 well area located on the north slope of Baiyun Sag. And other geochemical discriminant methods were applied simultaneously to determine the type and source rocks of natural gas. The results show that the natural gas in the Y5 well area on the northern slope of Baiyun Sag is mainly kerogen degradation gas, mixed with a small amount of oil cracking gas. The mixture of kerogen degradation gas and a small amount of crude oil cracking gas caused the inversion of the carbon isotope sequence of ethane and propane. The natural gas in the Y5 well area mainly comes from delta–shallow lacustrine facies source rock. The high–quality reservoirs in the shallower strata accumulate natural gas generated in the early stage, and the tight reservoirs in the deeper strata mainly accumulate natural gas generated in the late stage.

The paper presents the results of geological interpretation of the set of geophysical data with substantiation of geological-geophysical and structural geological criteria of oil and gas potential of the sedimentary cover deep levels and the upper part of the consolidated basement in the central West Siberian oil and gas basin. Gravity, magnetic and seismic data are used. The character of manifestation of the regional Pai-Khoi–Altai strike-slip zone covering an area up to 200 km wide is shown. The study provides a basis for assuming a spatial genetic relationship between the conditions for localizing hydrocarbon traps and the extensional and strike-slip and thrust structures of the zone that form so-called "flower structures". The substantiated structural geological criteria were applied to solve the problem of pattern recognition with training, highlighting the environments favourable for localization of hydrocarbon fields.

The real-time monitoring of food freshness in refrigerators is of significant importance in detecting potential food spoiling and preventing serious health issues. One method that is commonly reported and has received substantial attention is the discrimination of food freshness by the tracking of volatile molecules. Nevertheless, the ambient environment of low temperature (normally below 4^oC) and high humidity (90% R.H.) as well as poor selectivity in sensing gas species remain the challenge. In this research, an integrated smart gas-tracking device is designed and fabricated. By applying pump voltage on the yttria-stabilized zirconia (YSZ) membrane, the oxygen concentration in the testing chamber can be manually tailored. Due to the working principle of the sensor following the mixed potential behavior, distinct differences in sensitivity and selectivity are observed for the sensor that operated at different oxygen concentrations. Typically, the sensor gives satisfactory selectivity to H₂S, NH₃, and C₂H₅OH at the oxygen concentrations of 10%, 30%, and 40%, respectively. In addition, an acceptable response/recovery rate (within 24 s) is also confirmed. Finally, a refrigerator prototype that includes the smart gas sensor is built, and satisfactory performance in discriminating food freshness status of fresh or semi-fresh is verified for the proposed refrigerator prototype. In conclusion, these aforementioned promising results suggest that the proposed integrated smart gas sensor could be a potential candidate for alarming food spoilage.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Gas turbine power plants have important roles in the global power generation market. The examines thermodynamically the impact of steam injection for a combined cycle including a gas turbine cycle with a two-stage turbine and carbon dioxide recompression. The combined cycle is compared with the simple case without steam injection. Steam injection’s impact is observed on important parameters such as energy efficiency, exergy efficiency, and output power. It is revealed that steam injection reduces exergy destruction in components compared to the simple case. The efficiencies for both cases are obtained. The energy and exergy efficiencies respectively are found to be 30.4% and 29.4% for the simple case, and 35.3% and 34.1% for the case with steam injection. Also, incorporating steam injection reduces emissions of carbon dioxide.

Approximately 2 TCF (Trillion Cubic Feet) of acid gas are projected to be injected into the Surmeh formation. The recommended injection rate is 180 MMSCFD (Million standard cubic feet per day), based on acid gas content and gas in place of the source of injection. The tight nature of the Surmeh formation limits injectivity, with a maximum achievable rate of 7 MMSCFD for permeability of 1 mD (millidarcy). However, higher porosity (12%) and permeability of 100 mD enable more efficient injection without fracturing the formation. This study provides valuable insights into the feasibility of AGI in saline aquifers, emphasizing reservoir characterization, geomechanics, caprock integrity, and rock properties. The findings contribute to the implementation of environmentally sustainable acid gas disposal at offshore reservoirs.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

With the current increase in the demand from animal and agricultural products, management of agrowaste has become critical to avoid greenhouse gas emissions. The present article investigates the applicability of ammonium bicarbonate synthesis via flash distillation to valorize and stabilize several types of anaerobic digestate produced from individual fermentations of amino acids. Prior to the development of the model in Aspen Plus v12, the description of the system aqua-ammonia-carbon dioxide provided by the electrolyte non-random two-liquid property method was validated with empirical data available in the literature. The content of CO₂ in the digestate was found to be responsible of the OH alkalinity (0.4 equivalents of acid/kg digestate), while the partial and total alkalinities (0.8 eq/kg digestate) were essentially derived from the content of NH₃. The most suitable conditions for the flash distillation were 95 ⁰C and 1 bar with the condensation occurring at 25 ⁰C. However, in order to attain the precipitation of NH₄HCO₃ in the distillate, it was necessary to consider digestates with a moisture content of 50 wt.%, since the minimum levels of inorganic nitrogen and inorganic carbon were not attained otherwise. Even under these conditions, few amino acids (i.e. arginine, glycine, and histidine) were able to provide an anaerobic digestate, upon fermentation, that would be suitable for NH₄HCO₃ stabilization. Despite alanine digestate and glutamine digestate presented sufficient concentrations of inorganic nitrogen and inorganic carbon, the NH₄HCO₃-stabilization was not feasible due to the limited volatilization of NH₃. The process of stabilization with a capacity of a tonne of digestate per hour was improved by adding hydrochloric acid or sodium hydroxide at rates 44 kg/h, leading to production of 34 kg NH₄HCO₃/h. The economic viability of this process needs to be investigated considering not only the market value of the isolated inorganic fertilizer but the carbon credits saved, resulting from handling a more stabilized organic manure. Furthermore, given the role of the volatile elements of the biogas as endogenous stripping agents, it is recommended to use a fresh and saturated digestate as feed for the flash distillation.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Recently, there has been increasing attention toward inhaled nanoparticles (NPs) to develop in-halation therapies for diseases associated with the pulmonary system and investigate the toxic ef-fects of hazardous environmental particles on human lung health. Taking advantage of microfluidic technology for cell culture applications, lung-on-a-chip devices with great potential in replicating the lung air-blood barrier (ABB) have opened new research insights in preclinical pathology and therapeutic studies associated with aerosol NPs. Surprisingly, the air interface in such devices, which makes them tremendously unique among the other common liquid-based cellular mi-crosystems and enables exposure of cultivated cells to the drug/toxic aerosols, has been largely disregarded. Accordingly, there exists a significant research gap in the comprehensive under-standing of the NPs’ dynamics in the lung-on-a-chip devices, which is momentous to control the injection of aerosols to the target area and attain a desired physiochemical efficacy. To address this research gap, a numerical parametric study is presented to provide a deep insight into the dynamic behavior of the airborne NPs in a gas-liquid dual-channel lung-on-a-chip device with a porous membrane separating the channels. A finite element multi-physics model is developed to enable a particle tracing investigation simultaneously in both air and medium phases to replicate the in vivo conditions avoiding laborious and costly experimental trials. The results include the impact of fluid flow as well as geometrical properties on the distribution, deposition, and translocation of the NPs with diameters ranging from 10 nm to 900 nm in the lung-on-a-chip. The obtained results strongly suggest the aerosol injection of NPs instead of the aqueous solution for more efficient deposition on the substrate of the air channel and higher translocation to the media channel. The current study proposes to optimize the affecting parameters to control the injection and delivery of aerosol par-ticles into the lung-on-chip device depending on the objectives of biomedical investigations and provides optimized values for some specific cases. Therefore, this study can assist scientists and researchers in complementing their experimental investigation in future preclinical studies on pulmonary pathology associated with inhaled hazardous and toxic environmental particles, as well as therapeutic studies for developing inhalation drug delivery.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Pig behavior is an integral part of health and welfare management, as pigs usually reflect their inner emotions through behavior change. The livestock environment plays a key role in pigs' health and wellbeing. A poor farm environment increases the toxic GHGs, which might deteriorate pigs' health and welfare. In this study a computer-vision-based automatic monitoring and tracking model was proposed to detect short-term pigs' physical activities in a compromised environment. The ventilators of the livestock barn were closed for an hour, three times in a day (07:00-08:00, 13:00-14:00, and 20:00-21:00) to create a compromised environment, which increases the GHGs level significantly. The corresponding pig activities were observed before, during, and after an hour of the treatment. Two widely used object detection models (YOLOv4 and Fast-er R-CNN) were trained and compared their performances in terms of pig localization and posture detection. The YOLOv4, which outperformed the Faster R-CNN model, coupled with a Deep-SORT tracking algorithm to detect and track the pig activities. The results showed that the pigs became more inactive with the increase in GHG concentration, reducing their standing and walking activities. Moreover, the pigs also shortened their sternal-lying posture increasing the lateral lying posture duration at higher GHG concentration. The high detection accuracy (mAP: 98.67%) and tracking accuracy (MOTA: 93.86% and MOTP: 82.41%) signify the models’ efficacy in monitoring and tracking pigs' physical activities non-invasively.

In this work epitaxial Au islands have been grown on epitaxial α-Fe2O3 thin film by pulsed laser deposition on SrTiO3(111) substrate. Both Au and α-Fe2O3 layer show an island-type growth with an average particle size of 40 and 62 nm, respectively. The crystallographic coupling of lattices is confirmed with a rotation of 30º between the in-plane crystallographic axes of α-Fe2O3(0001) structure and those of SrTiO3(111) substrate and between the in-plane crystallographic axes of Au(111) and those of α-Fe2O3(0001) structure. α-Fe2O3 is the only phase of iron oxide identified before and after its functionalization with Au nanoparticles. In addition, its structural character-istics are also preserved after Au deposition, with minor changes at short-range order. The func-tional character of the complex systems as gas sensor has been proven at room temperature. Con-ductance measurements of Au(111)/α-Fe2O3(0001)/ SrTiO3(111) system show that the incorpora-tion of Au islands on top of the α-Fe2O3(0001) layer induces an enhancement of the gas-sensing ac-tivity for CO and CH4 gas in comparison to a bare α-Fe2O3(0001) layer grown on SrTiO3(111).

The frequent incidents of oil spills and other forms of pollution arising from crude oil exploration and exploitation (OEE) in the Niger Delta have caused several investigations on Polycyclic Aromatic Hydrocarbons (PAHs) pollution. This study aimed at developing a comprehensive report on PAH pollution and its human health risks recorded in the Niger Delta. Studies were extracted from Google Scholar, PubMed, and ResearchGate using a defined selection criterion. The quality of each study was assessed using the Newcastle – Ottawa Scale. Thirty-eight studies were selected with the majority reporting on PAH pollution in aquatic environments. Across all the selected studies, the total number of PAHs recorded ranged from 7 to 28 PAH congeners. Also, PAH potential sources reported in the studies were of pyrogenic and petrogenic sources. PAH concentrations recorded in water, sediment, aquatic organisms (fish and shrimp), soil, dust, and crop samples ranged from below detection limit (BDL) to 450 ± 117.9 mg/L, BDL to 1821.5 mg/kg, 0.005 to 1.098 mg/kg, ND to 4154 ± 3461 mg/kg, 165.1 to 1012 mg/kg, and 0.020 to 3.37 mg/kg, respectively. Majority of the selected studies reported PAH levels which were higher than the permissible limits. Incremental Lifetime Cancer Risk (ILCR) assessment of PAHs in samples ranged from low to high via ingestion and dermal routes of exposure to humans. It is recommended that the Federal Government of Nigeria promotes environmentally friendly operations of OEE. Future studies should focus on PAH pollution in farmlands, ambient air and the associated human and ecological health risks.

The co-electrolysis of CO2 and H2O at intermediate temperature is a viable approach for the power-to-gas conversion that deserves for further investigation, considering the need for green energy storage. The commercial solid oxide electrolyser is a promising device, but it is still facing to solve issues concerning the high operating temperatures and the improvement of gas value. In this paper we reported the recent findings of a simple approach that we have amply suggested for solid oxide cells consisting in the addition of a functional layer coated to the fuel electrode of commercial electrochemical cells. This approach simplifies the transition to the next generation of cells manufactured with the most promising materials currently developed and improves the gas value in the outlet stream of cell. Here, the material in use as a coating layer consisted of a Ni-modified La0.6Sr0.4Fe0.8Co0.2O3 which was developed and demonstrated as promising fuel electrode for solid oxide fuel cells. The results discussed in this paper proved the positive role of Ni-modified perovskite as a coating layer for the cathode, since an improvement of about twice was obtained about the quality of gas produced.

In this paper we develop a “general equilibrium” (GE) model for the allocation of exhaustible natural resources to examine the impact of different extraction scenarios on intergenerational economic welfare. We apply a stylized GE model to Israel's natural gas (NG) market to evaluate economic indicators resulting from NG-extraction scenarios: a baseline scenario based on current policy in the NG sector, a conservative scenario based on a lower extraction rate, and an intensive scenario based on faster extraction. We also examine the impact of various resource income-allocation strategies on intergenerational economic welfare through the mechanism of a “sovereign wealth fund” (SWF). The results indicate that a higher NG-extraction rate combined with an appropriate investment strategy for NG profits is preferable from an economic perspective to a conservative rate. Investment of the government take from the NG market in research and development (R&D) of renewable electricity productivity can sustainably increase economic welfare.

Paper discussed the problem of proper process of gas-freeing and ventilation of vessel cargo tank after washing process in aim to the entrance into the tank and its inspection. Correct assessment of atmosphere composition into the cargo tank is a basic condition of safe entrance and work of a crew. It should be done following actions: assessment of flammability hazard, the presence of other toxic gases for human and oxygen concentration. In the aim ship-owner should prepare adequate procedures: before entrance, during work and on emergency situations. On a vessel the assessment performs responsibility (entitled) officer whose decisions are crucial for the safety of prosecuting operations. The one of primary problem is proper (adequate) assessment of oxygen concentration in the air into the tank (enclosed spaces) after the measurement which should be properly interpreted. It concerns basically such situations when the oxygen concentration into the tank after measure leads the value over 22% or below 20.6% of volume (mole) contribution (v/v).

We hypothesized possibility that inline registered reticulorumen pH can be as biomarker of cows reproduction and health status. Aim of this study was to evaluate the relationship of reticulorumen pH with biomarkers from automatic milking system (AMS) and some blood parameters and determinate reticulorumen pH as biomarker of cows reproduction and health status. According to cows reproductive status the cows were classified as belonging to the following four groups: 15-30 d. postpartum; 1-34 d. after insemination; 35 d. after insemination (non-pregnant); 35 d. after insemination (pregnant). According reticulorumen pH assay experimental animals were divided into four classes: 1) pH<6.22 (5.3% of cows), 2) pH - 6.22-6.42 (42.1% of cows), 3) pH - 6.42-6.62 (21.1% of cows), 4) pH >6.62 (10.5% of cows). Rumination time, body weight, milk yield, milk fat – protein ratio, milk lactose, milk somatic cell count (SCC), milk electrical conductivity of all quarters of udder were registered with the help of Lely Astronaut® A3 milking robots. The pH, temperature of the contents of cow reticulorumens and cow activity were measured using specific smaX-tec boluses. Blood gas parameters were analyzed using a blood gas analyzer (EPOC, Canada). We found that pregnant cows has higher reticulorumen pH during insemination time, comparing with non-pregnant. Cows with lower reticulorumen pH has lowest milk fat – protein ratio, and lactose concentration, and highest SCC. Cows with lowest reticulorumen pH has lowest blood pH. With increase reticulorumen pH, increases blood potasium and hematocrit, decreases CO2, saturation and sodium.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

Original and improved version of the Hardy Cross iterative method with related modifications are today widely used for calculation of fluid flow through conduits in loops-like distribution networks of pipes with known node fluid consumptions. Fluid in these networks is usually natural gas for distribution in the municipalities, water in waterworks or hot water in district heating system, air in the case of ventilation systems in buildings or mines, etc. Since, the resistances in these networks depend of flow, problem is not linear like in electrical circuits, and iterative procedure must be used. In both version of the Hardy Cross method, in original and in the improved one, initial results of calculation in iteration procedure is not flow, but rather the correction of flow. Unfortunately, these corrections should be added to or subtracted from a flow calculated in previous iteration according to complicate algebraic rules. After the here presented node-loop method, final results in each of the iterations is flow directly rather than flow correction. In that way complex algebraic scheme for sign of flow correction is avoided, while the final results still remain unchanged. Numbers of required iterations for the same results are comparable with the improved Hardy Cross method.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

In the present work a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based ZIF-8, and ZIF-67 nanocrystals (pure and combined with gold nanoparticles) as sensitive layers has been tested as a non-invasive system to detect and differentiate disease markers, such as acetone, ethanol and ammonia, related with early diagnosis of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous and homogenous sensitive layers. Low concentrations (5 ppm, 10 ppm and 25ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

A growing number of companies in the brewery industry have made commitments to measure and reduce their greenhouse gas (GHG) emissions. However, many brewers, particularly craft brewers with relatively low rates of production, have struggled to meet these commitments. The purpose of this research was to investigate the challenges and benefits of measuring and reducing GHG emissions in the craft brewery industry. The research was conducted in Ontario, Canada, which has seen strong recent growth in the craft brewery industry. A case study and semi-structured interviews among Ontario Craft Brewers were conducted. The case study found that indirect (scope 3 emissions under the WBCSD & WRI GHG Protocol) GHG sources accounted for 46.4% of total GHGs, with major sources from barley agriculture, malted barley transportation, and bottle production. Direct emissions (scope 1) accounted for only 14.9% of GHGs, while scope 2 emissions, comprised mainly of energy consumption, accounted for 38.7% of GHGs. The case study and interviews found that the main challenges in calculating brewery GHGs are secondary data availability, technical knowledge, and finances. The study also found that the main benefits for Ontario breweries to measure their GHGs include sustainability marketing and preserving the environment. The interviews also found a poor understanding of carbon regulation among Ontario Craft Brewers, which is interesting considering that Ontario implemented a provincial cap and trade program in 2017.

Today, two very efficient methods for calculation of flow distribution per branches of a looped gas pipeline are available. Most common is improved Hardy Cross method, while the second one is so-called unified node-loop method. For gas pipeline, gas flow rate through a pipe can be determined using Colebrook equation modified by AGA (American Gas Association) for calculation of friction factor accompanied with Darcy-Weisbach equation for pressure drop and second approach is using Renouard equation adopted for gas pipeline calculation. For the development of Renouard equation for gas pipelines some additional thermodynamic properties are involved in comparisons with Colebrook and Darcy-Weisbach model. These differences will be explained. Both equations, the Colebrook’s (accompanied with Darcy-Weisbach scheme) and Renouard’s will be used for calculation of flow through the pipes of one gas pipeline with eight closed loops which are formed by pipes. Consequently four different cases will be examined because the network is calculated using improved Hardy Cross method and unified node-loop method. Some remarks on optimization in this area of engineering also will be mentioned.

Tributyltin (TBT) is one of the most toxic anthropogenic compounds introduced into the marine environment. Despite its global ban in 2008, TBT is still a problem of great concern due to its high affinity for particulate matter, providing a direct and potentially persistent route of entry into benthic sediments. Bioremediation strategies may constitute an alternative approach to conventional physicochemical methods, benefiting from the microorganism’s potential to metabolize anthropogenic compounds. In this work, a simple, precise and accurate static headspace gas chromatography method was developed to investigate the ability of TBT degrading microbes in sedimentary microcosms over a period of 120 days. The proposed method was validated for linearity, repeatability, accuracy, specificity, limit of detection and limit of quantification. The method was subsequently successfully applied for the detection and quantification of TBT and degrading compounds in sediment samples on day 0, 30, 60, 90 and 120 of the experiment employing the principles of green chemistry. On day 120 the concentration of TBT remaining in the microcosms ranged between 91.91 ng/g wet wt for the least effective microbial inoculant to 52.73 ng/g wet wt for the most effective microbial inoculant from a stating concentration of 100 ng/g wet wt.

Liquid propellants are fast becoming attractive for pulsed plasma thrusters due to their high efficiency and low contamination issues. However, the complete plasma interaction and acceleration processes are still not very clear. Present paper develops a multi-layer numerical model for liquid propellant PPTs. The model proposes a possible acceleration mechanism for liquid fed pulsed plasma thrusters and accurately predicts the propellant utilization capabilities and estimations for the fraction of propellant gas that is completely ionized and accelerated to high exit velocities. Validation of the numerical model and the assumptions on which the model is based on is achieved by comparing the experimental results from two different liquid-fed thrusters developed at the University of Tokyo. Results show 50% of liquid propellant injected is completely ionized and accelerated to high exit velocities (> 50Km/s), whereas, neutral gas contribute to only 7% of the total specific impulse and accelerated to low exit velocity (< 4Km/s). The model shows an accuracy up-to 92%. Optimization methods are briefly discussed to ensure efficient propellant utilization and performance. The model acts as a tool to understand the background physics and to optimize the performance for liquid-fed PPTs.

Based on the geologic conditions of natural gas hydrate (NGH) accumulations in the Shenhu area, northern slope of the South China Sea, this paper used a method of combining reservoir stimulation technique (RST) with depressurization to investigate the conversion efficiency of marine NGH reservoirs in different intrinsic permeability and initial NGH saturation conditions, and analyze the influence of variably-stimulation effect on marine NGH conversion efficiency in different accumulation conditions, provided a reference scheme for improving the NGH conversion efficiency in the Shenhu area. In this work, we performed calculations for the variations in CH4 production rate and cumulative volume of CH4 in different initial NGH saturation, intrinsic permeability and stimulation effect conditions, variance analysis and range analysis methods were used to analyze the significance of these key factors and their interaction, and investigated the sensitivity of stimulation effect on NGH conversion efficiency, respectively. The simulation results showed that stimulation effect have a significant influence on NGH conversion efficiency, and the influence of interaction between these three factors were not obvious. Possibly most important, we clarified an optimum stimulation effect for higher NGH conversion efficiency under different accumulation conditions, especially in low-permeability and high-saturation, which corresponding stimulation effect were different.

Dynamic tribochemical processes for dicationic ionic liquid containing a germinal imidazolium cation head groups bridged by a poly(ethylene glycol) and bis(trifluoromethylsulfonyl)imide anion were studied using time-resolved Mechanically Stimulated Gas Emission Mass-Spectrometry (MSGE-MS). In comparison with similar monocationic imidazolium ionic liquids with short alkylic or long polyether side chains the dicationic ionic liquid had lower coefficient of friction on Ti6Al4V alloy and smoother behaviour. The analysis of volatile decomposition products suggested multiple tribochemical reactions in which both anionic and cationic moieties are involved. Tribochemical degradation of cations was mainly through detachment of the side and bridging chains from the imidazolium head groups. Absence of volatile products containing nitrogen implies that imidazole group remained unchanged. Hydrogen and water desorption were attributed to the reactions of hydrogen fluoride being a product of anion degradation with titanium and titanium oxide.

The Western Balkans region is persistently vulnerable to natural hazards, inadequate infrastructure, and limited institutional capacities, necessitating a collaborative approach to disaster risk management. This paper presents a comprehensive project led by the Scientific-Professional Society for Disaster Risk Management (NSD-URVs) in Belgrade, aiming to establish and strengthen a regional network of experts in disaster risk management. The project focuses on building expertise, facilitating knowledge exchange, promoting expert coordination, and enhancing cross-border collaboration. Key activities include developing a web platform, organising an international conference, and advocating for regional policies that integrate best practices and innovations in disaster risk management. The expected outcomes are the establishment of a cohesive network, enhanced expertise and coordination, and improved preparedness and responsiveness to disasters. By leveraging collective expertise and resources, this initiative aims to fortify the region's resilience against potential disasters. Addressing the identified gaps and implementing the proposed policy recommendations can significantly enhance the region's resilience to natural hazards. Future research should focus on the implementation and impact of these recommendations to ensure continuous improvement in disaster preparedness and response.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

In this work, a numerical study on the loop-terminated Mach-Zehnder interferometer (LT-MZI) structure for CO2 gas sensing application is carried out via the finite element method. The sensing arm is covered with a polyhexamethylene biguanide (PHMB) polymer which is highly receptive to CO2 gas. The refractive index of the host material decreases due to the absorption of the CO2 gas resulting in a shift in the interference pattern of the LT-MZI structure. As a result, a redshift in the wavelength is observed in the transmission spectrum of the device. The sensitivity of the device is estimated at 7.63 pm/ppm, 34.46 pm/ppm and 74.78 pm/ppm for the sensing arm length of 5 µm, 10 µm, and 15 µm, respectively. The sensitivity can be further enhanced, however at the cost of the bigger footprint of the device. Utilizing the innovative sensor design, a comprehensive range of CO2 gas concentrations spanning from 0 to 524 ppm is successfully detected. This compact and highly sensitive device serves as a vital tool for monitoring indoor CO2 levels, fostering a healthier breathing environment for all occupants.

As the world attempts to decarbonise the food industry and limit greenhouse gas (GHG) emissions, plant-based meat analogues (PBMAs) have emerged as a sustainable alternative to traditional meat. This study implemented a life cycle assessment (LCA) to rigorously compare the environmental impacts of a beef burger (BB), produced with British beef, against a meat analogue (MA) equivalent with a publicly available recipe. For the LCA, a cradle-to-fork system boundary was utilised, alongside a functional unit of a single 100 g burger patty. Results from the LCA revealed that the BB patty had more than double the total environmental impact than the MA equivalent, as well as possessing a global warming impact that was 62% higher. A simple extrapolation illustrated that if the UK population switched from beef to meat analogue patties, 3 million tonnes of CO2e could be saved annually, corresponding to 0.74% of the country’s yearly territorial GHG emissions. Scenario analyses displayed how the environmental impact of the MA patty remained stable regardless of changes in exportation, ingredient origin or soy protein sourcing. Moreover, sensitivity analysis conducted with an alternative characterisation method corroborated initial findings, whilst uncertainty analysis ensured that nearly all conclusions generated from the original comparison were robust. Future studies should conduct peer-reviewed LCAs on PBMA patties with commercial recipes based on other plant-based proteins, as well as fully understanding any potential health implications of long-term PBMA consumption.

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

AlphaFold is a groundbreaking Deep Learning tool for protein structure prediction. It achieved remarkable accuracy in modeling the many 3D structures while taking as the input only the known amino acid sequence of proteins in question. Intriguingly though, in the early steps of each individual structure prediction procedure, AlphaFold is not respecting topological barriers that in real proteins result from the reciprocals impermeability of polypeptide chains. This study aims to investigate how this non-respecting of topological barriers affects AlphaFold predictions with respect to the topology of protein chains. We focus on such classes of proteins that during their natural folding form reproducibly the same knot type on their linear polypeptide chain as revealed by their crystallographic analysis. We use partially artificial test constructs in which the mutual non-permeability of polypeptide chains should not permit the formation of such knots during natural protein folding. We find that despite the formal impossibility that the protein folding process could produce such knots, AlphaFold predicts these proteins to be knotted. Our study underscores the necessity for cautious interpretation and further validation of topological features in protein structures predicted by AlphaFold.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and &gt;115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Large ruminant production is associated with high greenhouse gas emissions (GHGe) intensity, with the highest in southeast Asia being Laos at 102.9 CO2eq/kg meat produced, compared with average global meat emissions intensity of 33 CO2eq/kg. As recent studies in Laos identified emissions control molasses blocks (ECBs) achieved abatement of 470kg CO2eq/20kg block consumed, a study was conducted with a supplement mix with reported methane reducing properties, containing plant tannins and citral extract, salt, molasses and water. Groups of housed dairy buffalo (n=7) and pasture-fed grazing beef cows (n=11) were randomly selected, body condition scores estimated (BCS:1-5) and baseline nasa-oral methane eructation measured daily for 2 weeks. All animals were offered 300-400g/day of the mix for a month, with buffalo accessing abundant fresh cut forages whereas the grazing cows accessing rice straw and pasture declining in quality and quantity due to severe drought. The buffalo consumed all of the mix and retained their BCS of 3, whereas the cattle consumed between 200-300g/day of the mix and their BCS declined from 1.5 to 1.0 during the trial. Analysis of data points (buffalo n=309; cattle n=378) found average methane concentration (AMP) per animal of both cohorts increased over the 2 week baseline period, then declined during the supplementation period by 36% in the buffalo and 18% in cattle cohorts.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

The purpose of this work was to evaluate a novel methodology developed by Digital Blood Corporation (DBC) to calculate critical blood values using four non-invasive measured values as input. The values obtained using a point-of-care testing (POCT) device were utilized for comparison and reference. Radial arterial blood was collected for the POCT comparator analysis using the Abbott i-STAT^® device. The non-invasive methodology from DBC requires four parameters to be directly measured: temperature, hemoglobin, pO2, and pCO2. Subsequently, sodium, potassium, chloride, ionized calcium, total carbon dioxide, pH, bicarbonate, and oxygen saturation are calculated using an algorithm. The agreement between the POCT and DBC’s methodology was analyzed using Bland-Altman difference plots. For a second data set, pO2 and pCO2 values collected with the POCT were used as input for DBC’s algorithm to test its robustness. Data from 37 healthy ambulatory individuals, mean age: 42.4 + 13 years; range: 18-64 years, were included in the primary analysis. In the case of the non-invasive gained four input values the greatest variation between POCT and DBC’s approach was observed for pO2 and consequently for algorithm values that depend upon pO2 precision. Replacing transcutaneous pO2 and pCO2 with POCT values demonstrates the principal ability of DBC’s algorithm to predict the additional 8 blood values in sufficient agreement with a standard POCT device in healthy patients. The algorithm developed by DBC appears to be robust in the case of healthy patients but does need the four measured input values with preciseness comparable to a POCT device to give reliable and clinically relevant results. The present study thus serves as a proof of concept to facilitate future study and further development of this methodology into a non-invasive device.

Reservoir in the Central Structural Zone of the Xihu Sag is the Huagang Formation, dominated by natural gas reservoirs, and the reservoir in the Western Slope Zone is the Pinghu Formation, dominated by light oil and wet gas. In this paper, the Gas Drive Water Displacement- Magnetic Resonance Imaging (GWD-MRI) experiments are used to simulate the charging characteristics of the sandstone migration layer. The centrifugal- Magnetic Resonance (Cen-NMR) experiments simulate the short-term fast trap charging process, and the Semi-Permeable Baffle (SPB) charging experiment simulates the slow trap accumulation process. Studies have shown that there is a start-up pressure for the migration layer charging, and the start-up pressure of the core with a permeability of 0.3mD is about 0.6MPa. Experimental simulations have confirmed that there is a front zone with changed water saturation, with a width of about 1-1.5cm. The migration layer charging mainly has two actions, drive effect and carry effect. The drive effect reduces the water saturation to 70%-80%, and the carry effect can still reduce the water saturation by 5%-10%. The water saturation of rapid charging is mainly affected by the petro-physical. The porosity is high, the water saturation is low. The water saturation decreased significantly with the increase of centrifugal force when the centrifugal force is smaller. If the centrifugal force is greater than 0.8 MPa, the water saturation decreases slowly. The water saturation of the trap slowly charging is basically maintained at 40%-50%, which matches the water saturation of the airtight coring from 40%-55%, the petro-physical do not affect the final water saturation.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

The total lipid and protein content of the invasive caprellid amphipod Caprella scaura, from the biofouling communities of fish farm cages in the Pagasitikos Gulf were analyzed and compared among seasons. Proteins were the most abundant component (48.5 – 49.3%). Lipid content was relatively lower, with a wider range (6.7 – 34%) and showed a distinct seasonal fluctuation with high values in the winter population and a gradual decrease in spring and summer, with the lowest values in Autumn. Composition of the fatty acids profile was consistent among the seasons, with palmitic (16:0), Oleic (18:1n-9), Eicosapentanoic (20:5n-3)(EPA) and Docosahexanoic acid (22:6n-3 )(DHA) being the most abundant fatty acids. The presence of high levels of EPA and DHA fatty acids makes the species a potential candidate for use of these organisms in aquaculture.

Transplant of human cancer cells into zebrafish larvae has emerged as a useful methodology in cancer research. Zebrafish have very low husbandry costs, are amenable to large-scale drug screening, and are unmatched for optical clarity in live animal imaging. However, there is currently no consensus on the ideal methods for xenograft of human cancer cells into zebrafish. Here, we have examined the effects of transplant site and housing temperature on both zebrafish larvae and human cancer cells using survival analyses, metabolomic approaches, and in vivo imaging. Our data show that while zebrafish larvae can adapt to the ideal conditions for mammalian cells, human cancer cells are highly sensitive to both temperature change and transplant site. Human cells housed in slightly cooler than physiologic temperatures had a significantly altered metabolism that resulted in changes in growth, survival, and response to chemotherapy. Cancer cells xenografted into the yolk of the larvae also had reduced proliferation and drug response compared to those xenografted into the soma, in part due to the differences in metabolites available at these sites. In total, temperature and transplant site can have profound effects on xenografted cells. Standardization of zebrafish xenograft methods will enhance data reproducibility between individual laboratories.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

Monitoring volatile organic compounds (VOCs) places a crucial role in environmental pollutants control and indoor air quality. In this study, a metal-oxide (MOx) sensor detector (used in a commercially available monitor) was employed to delineate the composition of air containing three common VOCs (ethanol, acetone and hexane) under various concentrations. Experiments with a single component and double components were conducted to investigate how the solvents interact with the metal oxide sensor. The experimental results revealed that the affinity between VOC and sensor was in the following order: acetone > ethanol > n-hexane. A mathematical model was developed, based on the experimental findings and data analysis, to convert the output resistance value of the sensor into concentration values, which in turn can be used to calculate a VOC-based air quality index. Empirical equations were established based on inferences of vapor composition versus resistance trends, and on an approach of using original and diluted air samples to generate two sets of resistance data per sample. The calibration of numerous model parameters allowed matching simulated curves to measured data. As such, the predictive mathematical model enabled quantifying not only the total concentration of sensed VOCs, but also estimating the VOC composition. This first attempt to obtain semi-quantitative data from a single MOx sensor, despite remaining selectivity challenges, is aimed at expanding the capability of mobile air pollutants monitoring devices.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Effectively avoiding gas accident is vital to the security of mineral manufacture, and the coal mine gas accident is often caused by gas concentration overrun. The prediction accuracy of gas emission quantity in coal mine is the key to solve this problem. To maintain concentration of gas in a secure range，grey theory and neural network model increasingly diffusely used in forecasting gas emission quantity in coal mine critically. Nevertheless, the limitation of the grey neural network model is that researchers merely bonded the conventional neural network and grey theory. To enhance accuracy of prediction, a modified grey GM(1,1) and RBF neural network model is proposed combined amended grey GM(1,1) model and RBF neural network model. Then the proposed model was put into simulation experiment which is built based on Matlab software. Ultimately, conclusion of the simulation experiment verified that the modified grey GM(1,1) and RBF neural network model not only boosts the precision of prediction, but also restricts relative error in a minimum range. This showed that the modified grey GM(1,1) and RBF neural network model achieves effectiveness in precision of prediction much better than grey GM(1,1) model and RBF neural network model.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

Environmental assessment is a concept that has been designed to facilitate the present generation to meet their needs without compromising the ability of future generations to meet their own needs as well. Thus, this concept has drawn significant attention from various scholars, researchers and industrial practitioners around the world over the past three decades. Life Cycle Environmental Assessment (LCEA) is a widely metric used to assess the potential ecological impacts, which can be caused by electricity generating supply systems or by other systems than power production plants. However, the current LCEA model is biased and ineffective. Because, its omits factors that are increasingly contributing to the ecological degradation. This study has identified the omitted factors through a critical analysis of a set of previous journal articles conducted in the energy sector. In light of this, this study has developed a novel LCEA framework addressing those blind spots. The framework developed in this study is holistic in nature including all the life cycle stages of a power supply system such as Extraction of the Raw Material (ERM), Transport of Raw Material (TRM), Conversion of Raw into Electricity (CRE), and Transmission and Distribution of Electricity (TDE) to the end users. The novel developed LCEA model has been tested and applied to nine power generation plants such as coal, gas, nuclear, biomass, geothermal, hydro, solar thermal, wind onshore and wind offshore. The results have demonstrated that of conventional technologies including coal, gas, and nuclear, coal energy generating source has got the highest life cycle greenhouse gas Grid Emission Factor (GEF) of 2866 kg CO2e/MWh, followed by gas with 728 kg CO2e/MWh, and nuclear has got the least GEF of 35 kg CO2e/MWh. Whereas of renewable energy sources biomass has got the highest GEF of 1508 kg CO2e/MWh, followed by solar thermal with 46.6 kg CO2e/MWh, hydro 39 kg CO2e/MWh, wind offshore 25.25 kg CO2e/MWh, wind onshore 10.1 kg CO2e/MWh, and geothermal closes the ranking with 6.23 kg CO2e/MWh.

We propose a wave-like design on the surface of cathode channels (wave form cathode channels) to improve oxidant delivery to gas diffusion layers (GDLs) [1-2]. We performed experiments using PEMFCs combined with wave form surface design on cathodes. We varied the factors of the distance between wave-bumps (the Adhesive distance, AD), and the size of the wave-bumps (the Expansion ratio, ER). The ADs are 3, 4, and 5 times the size of the half-circle bump’s radius, and the ERs are 1/1.5, 1/2, and 1/3 times the channel’s height. We evaluated the performances of the fuel cells, and compared the current-voltage (I-V) relations. For comparison, we prepared PEMFCs with conventional flat-surfaced oxygen channels. Our aim in this work is to identify fuel cell operation by modifying the surface design of channels, and ultimately to find the optimal design of cathode channels that will maximize fuel cell performance.

Currently, for the serious air pollution and global warming effect caused by the substance released from the present vehicle, it is expected that the regulatory requirements for the emission will become more stringent. A new concept of the combustion technology that can reduce the NOx and PM related to combustion is urgently needed. To cope with such social demands, many developed countries are efforts to develop the environment friendly vehicle engine at the national lever in order to satisfy with strengthening emission control. As a main combustion technology among new combustion technology for the new generation engine, the homogenous charge compression engine (HCCI) is expanding its application range by employing multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. In this paper, a multi-injection method in order to apply the HCCI combustion method without mainly altering engine specifications and practicality by referring to the results of the HCCI engine was investigated. Applied with forced charging, exhaust gas recirculation (EGR) and compression ratio change, it was evaluated to the possibility of securing optimum fuel economy and emission reduction in the IMEP 0.8 MPa range.

The Directive 2014/95, in force in 2017, is the first European step that requires mandatory non-financial information to undertakings (all “public interest entities” with more than 500 employees). The regulation is concerning sustainability information as environmental, social and employee, human rights and anti-corruption and bribery matters and disclosure of diversity policy for board members. The study, in the strand of the regulation of accounting, part of the broader field of research into accounting regulation, contributes to the debate on the quality of regulation, in this specific case referred to sustainability disclosure. The regulation of sustainability matters is studied in literature broadly in a post-implementation phase and at national level. This research, instead, aims to analyse, through the causal chain of regulatory policy, in the ex-ante stage, the quality of the regulation and, at least, the usefulness of the normative pressure. The Oil & Gas sector is chosen as sample of the study, because it is one of the most advanced sectors in sustainability disclosure. The examination of the law, in terms of content requirements (what) and location of information (where), is the basis to apply the disclosure-scoring system, a partial form of content analysis, to the reports of the sample. The findings reveal a good level of completeness of non-financial information, however, there are some areas that have to be improved to reach the requests of the Directive. Results show also the presence of overlap between financial reports and sustainability ones. In conclusion, the regulation is useful to prompt undertakings to reflect on their reporting and so doing improve their sustainability approach.

The aim of this study is to empirically examine the link between foreign direct investment (FDI) and domestic investment (DI) in South Africa over the period of 41 years (1975-2016). Accurately, it attempts to determine whether FDI crowds in or crowds out DI in South Africa. DI is sub-divided into private domestic investment (credit to domestic private sector) and public corporation investment (state owned enterprises). We used the Autoregressive Distributed Lag-Error Correction Model (ARDL-ECM) technique to ascertain long run and short run effects concurrently after establishing that the variables were stationary (using the PP test). The results of the unit root test shows that all variables are integrated of order zero I(0) or integrated of order one I(1), indicating that the series of variables are stationary in the level or first difference form. The findings revealed that variables are cointegrated in the long run. The ARDL model found a negative link between FDI and domestic investment. The result implies that FDI crowds out domestic investment. Moreover, the long run estimate revealed that domestic investment is crowded in by government investment expenditure (GINV). Other findings uncovered that, GDP crowds out private domestic investment while crowding in public corporation investment. Moreover, the long run estimate revealed that domestic investment is crowded in by gross domestic savings (SAV). On the other hand, the real exchange rate (EXCR) crowds out private domestic investment while crowding in public corporation investment. Trade openness (TRA) crowds out domestic investment. Additionally, the short run estimate uncovered that private domestic investment is crowded out by FDI, EXCR, and TRA whereas GINV, GDP and SAV is crowding in private domestic investment. Other findings discovered that, in the short run, public corporation investment is crowded out by FDI, GDP, EXCR and TRA, while GINV and SAV crowd in public corporation investment. The CUSUM confirms that the models are structurally firmness.

The climate change constitutes nowadays an enormous global threat for human health and environmental sustainability. The expanding world population and the increased global needs for food production have an important negative impact upon environment. Diet can link human health with environmental sustainability. Food production systems are closely related to anthropogenic greenhouse gas emissions and the aggravation of climate change, and current western type, animal-based, dietary patterns may lead to adverse environmental footprints. In the present narrative review, we address the interconnection of the Mediterranean diet (MD) with climate change and sustainability. MD is a highly recommended dietary intervention for the prevention and management of various endocrine and cardiometabolic diseases. Beyond its evidence-based, health-promoting effects, it also has beneficial environmental impact, reducing greenhouse gas emissions and enhancing biodiversity, food security and sustainability. Based on the evidence reviewed herein, MD should be incorporated within the framework of a “One Health” model, which involves the improvement not only of human health but also of planetary health and food system sustainability. Our review aims to provide a stimulus for health pro-fessionals to strongly recommend the implementation of MD under the current pressure of climate change, despite all barriers, targeting both human health preservation and the planetary well-being.

A new data processing method based on Machine Learning (ML) algorithms has been developed and tested in clinical environments during COVID-19 trials at the Medical University of South Carolina (MUSC). Breath samples have been collected in 2020–2021 from 100 participants using gas chromatography combined with ion mobility spectrometry (GC-IMS, G.A.S. mbH). Polymerase chain reaction (PCR) tests combined with clinical diagnostics were used as a reference method. Once the ML training-testing cycle is completed, the diagnostics of a single data set may be completed in as little as a few seconds. A convincing difference in the Volatile Organic Compounds (VOS) breath biomarker signature with COVID-19 positive and negative participants has been found. This approach is a generic method that can be applied to data sets collected with other types of hardware, e.g., different settings of GC, GC-MS, GC-GC, or other methods providing high information density in 2-dimensional data sets.

Onions are known not only for their culinary importance but also for their nutritional and health-promoting properties. Both properties are closely linked to its content of organosulfur compounds, which account for up to 5% of the dry weight of an onion. Given the importance of these compounds, suitable analytical methods are required for their study. Two techniques should be highlighted in this context: gas chromatography coupled to mass spectrometry (GC-MS), and liquid chromatography coupled to mass spectrometry (LC-MS). In this study, eight different onion varieties were analyzed using two distinct analytical techniques: direct thermal desorption–gas chromatography-mass spectrometry (DTD-GC-MS) and high-resolution mass spectrometry (HRMS) on an LC-ESI-QqTOF instrument. Each method identified 18 different organosulfur compounds, with LC-HRMS targeting non-volatile compounds, such as cysteine sulfoxides, and GC-MS targeting volatiles, such as disulfides and trisulfides. The results obtained were studied using Pearson correlations and principal component analysis. No precise correlation was found between the initial organosulfur compounds in onions and their hydrolysates. Consequently, although GC is one of the most employed techniques in the scientific literature, the use of LC-HRMS or a combination of both techniques may offer a more comprehensive and accurate description of the metabolomic profile of onions.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

This study evaluated gas mixtures of carbon dioxide (CO2) associated with nitrogen (N2) as al-ternatives to the use of CO2 in two phases to improve the welfare of broiler chickens at slaugh-ter. Broilers were exposed to one of three treatments: 40C90C (1st phase: <40% CO2 for 2 min; 2nd phase: >90% CO2 and <2% O2 for 2 min, n=92), 40C60N (40% CO2, 60% N2 and <2% O2 for 4 min, n=79), or 20C80N (20% CO2, 80% N2 and <2% O2 for 4 min, n=72). The time to onset of loss of consciousness (LOC) and death was assessed by brain activity (EEG) and behaviour. Behaviour also allowed characterisation of the aversive response to the treatments. Exposure to 40C60N and 20C80N induced LOC faster (19 s [14 – 30 s] and 21 s [16 – 37 s], respectively) but also with less inter-individual variability compared to 40C90C (53 s [26 – 156 s], P < 0.001) and birds took less time to die (40C60N: 64 s [43 – 108 s]; 20C80N: 70 s [45 – 88 s]; 40C90C: 177 s [89 – 212 s], P < 0.001). The 40C90C birds not only experienced more aversion during induction to LOC but are at risk of remaining conscious when the CO2 concentration is increased in the 2nd phase. From an animal welfare point of view, 40C60N provided the highest welfare, followed by 20C80N and 40C90C.

When attempting to quantify future harms caused by carbon emissions and to set appropriate energy policies, it has been argued that the most important metric is the number of human deaths caused by climate change. Several studies have attempted to overcome the uncertainties associated with such forecasting. In this article, approaches to estimating future human deaths tolls from climate change are compared and synthesized, and implications for energy policy are considered. Several studies are consistent with the “1000-ton rule,” according to which a future person is killed every time 1000 tons of fossil carbon are burned (order-of-magnitude estimate). If warming reaches or exceeds 2°C this century, mainly richer humans will be responsible for killing roughly 1 billion mainly poorer humans through anthropogenic global warming. Such mass manslaughter is clearly unacceptable. On this basis, relatively aggressive energy policies are summarized that would enable immediate and substantive decreases to carbon emissions. The limitations to such calculations are outlined and future work is recommended to accelerate the decarbonization of the global economy while minimizing the number of sacrificed human lives.

Low pasture biomass production and fodder scarcity are among the major challenges affecting productivity of dairy cattle farms in Sri Lanka. As a potential solution to this, two Napier hybrid cultivars CO-5 and Sampoorna were recently introduced and a field experiment was conducted to evaluate their growth, dry matter production and nutritional composition during May to September 2020. Plant measurements and samples were collected at five harvest intervals (4, 6, 8, 10 and 12 weeks after planting), with the plant samples subjected to biomass and nutritional assessments. The number of tillers and leaf length differed (P=0.01) between the two cultivars at 4 weeks harvesting interval (HI) whilst number of leaves differed at 12 HI respectively. Dry matter yield increased (P=0.16) almost linearly whilst crude protein declined exponentially with CO-5 greater than Sampoorna (P=0.057; 9.3% vs 8.7%), with increasing harvesting intervals respectively. In-vitro Organic Matter Digestibility and In-vitro Metabolizable Energy contents were similar across weeks 4, 6 and 8 but then decreased. This study demonstrates that higher dry matter yields (12.54 t/ha) can be obtained by harvesting both cultivars at 12 HI, but from a nutritional perspective harvesting at 6 HI during Yala season of the year would be optimum for farmers.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

The emergence of the COVID-19 pandemic has propelled the use of alcohol-based hand sanitizers to the fore as a SARS-CoV-2 control measure. To be effective these products must comply with relevant quality parameters such as alcohol concentration, methanol limits and purity. The current study was designed to determine the quality of alcohol-based hand sanitizer products in the Nairobi metropolitan area. For this purpose, 74 commercially marketed samples were collected and subjected to analysis by gas chromatography. Only three samples (4.1%) complied with the regulatory specifications for alcohol content, methanol limits and pH. Five samples (6.8%) complied with the specification for alcohol content but did not meet methanol or pH limits. A total of 44 (59.5%) samples had methanol levels that exceeded threshold limits. Eleven samples (14.9%) were found with methanol substitution (i.e., methanol, instead of ethanol or isopropanol, was the main alcohol component). The results show that users of alcohol-based hand sanitizers are being exposed to substandard and falsified products which in addition to being non-efficacious pose harm due to unacceptable levels of toxic impurities. Regular, routine post-market surveillance is needed to prevent such products from reaching the market.

Phenol is added to acetophenone (methyl phenyl ketone) and to six of its halogenated derivatives in a supersonic jet expansion to determine the hydrogen bonding preference of the cold and isolated 1:1 complexes by linear infrared spectroscopy. Halogenation is found to have a pronounced effect on the docking site in this intermolecular ketone balance experiment. The spectra unambiguously decide between competing variants of phenyl group stacking due to their differences in hydrogen bond strength. Structures where the phenyl group interaction strongly distorts the hydrogen bond are more difficult to quantify in the experiment. For unsubstituted acetophenone, phenol clearly prefers the methyl side despite a predicted sub-kJ/mol advantage which is nearly independent of zero point vibrational energy, turning this complex into a challenging benchmark system for electronic structure methods which include long range dispersion interactions in some way.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Parmigiano Reggiano cheese is one of the most appreciated and consumed food worldwide, especially in Italy, for its high content of nutrients and for its taste. However, these characteristics make this product subject to counterfeiting in different forms. In this study, a novel method based on an electronic nose has been developed in order to investigate the potentiality of this tool to distinguish rind percentage in grated Parmigiano Reggiano packages that should be lower than 18%. Different samples in terms of percentage, seasoning and rind working process were considered to tackle the problem at 360°. In parallel, GC-MS technique was used to give a name to the compounds that characterize Parmigiano and to relate them with sensors responses. Data analysis consisted of two stages: multivariate analysis (PLS) and classification made in a hierarchical way with PLS-DA ad ANNs. Results are promising in terms of correct classification of the samples. The classification rate is higher for ANNs than PLS-DA, reaching also 100% values.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Digital federated platforms and data cooperatives for secure, trusted and sovereign data exchange will play a central role in the construction industry of the future. With the help of platforms, cooperatives and their novel value creation, the digital transformation and the degree of organization of the construction value chain can be taken to a new level of collaboration. The goal of this research project was to develop an experimental prototype for a federated innovation data platform along with a suitable exemplary use case. The prototype is to serve the construction industry as a demonstrator for further developments and form the basis for an innovation platform. It exemplifies how an overall concept is concretely implemented along one or more use cases that address high-priority industry pain points. This concept will create a blueprint and a framework for further developments, which will then be further established in the market. The research project illuminates the perspective of various governance innovations to increase industry collaboration, productivity and capital project performance and transparency as well as the overall potential of possible platform business models. However, a comprehensive expert survey revealed that there are considerable obstacles to trust-based data exchange between the key stakeholders in the industry value network. The obstacles to cooperation are predominantly not of a technical nature, but of a competitive, predominantly trust-related nature. To overcome these obstacles and create a pre-competitive space of trust, the authors therefore propose the governance structure of a data cooperative model, which is discussed in detail in this paper.

Water electrolysis provides efficient and cost-effective production of hydrogen from renewable energy. Currently, the oxidation half-cell reaction relies on noble-metal catalysts, impeding widespread application. In order to adopt water electrolyzers as the main hydrogen production systems, it is critical to develop inexpensive and earth-abundant catalysts. This review discusses the proton exchange membrane (PEM) water electrolysis (WE) and the progress in replacing the noble-metal catalysts with earth-abundant ones. Researchers within this field are aiming to improve the efficiency and stability of earth-abundant catalysts (EACs), as well as to discover new ones. The latter is particularly important for the oxygen evolution reaction (OER) under acidic media, where the only stable and efficient catalysts are noble-metal oxides, such as IrO_x and RuO_x. On the other hand, there is significant progress on EACs for the hydrogen evolution reaction (HER) in acidic conditions, but how many of these EACs have been used in PEM WEs and tested under realistic conditions? What is the current status on the development of EACs for the OER? These are the two main questions this review addresses.

Carbon supported nanoparticles of monometallic Ni catalyst and binary Ni-Transition Metal (Ni-TM/C) electrocatalytic composites were synthesized via chemical reduction method, where TM stands for the doping elements Fe, Co, and Cu. The chemical composition, structure and morphology of the Ni-TM/C materials were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDS). The electrochemical properties towards hydrogen oxidation reaction in alkaline medium were studied using the rotating disc electrode and cycling voltammetry methods. A significant role of the TM dopant in the promotion of the hydrogen electrooxidation kinetics of the binary Ni-TM/C materials were revealed. A record-high in exchange current density value of 0.060 mA cm²_Ni was measured for Ni₃Fe₁/C, whereas the monometallic Ni/C counterpart has only shown 0.039 mA cm²_Ni. In order to predict the feasibility of the electrocatalysts for hydrogen chemisorption, density functional theory was applied to calculate the hydrogen binding energy and hydroxide binding energy values for bare Ni and Ni₃TM₁.

The limited information available on the structure of complexes involving transcription factors and cognate DNA response elements represents a major obstacle in the quest to understand their mechanism of action at the molecular level. We implemented a concerted structural proteomics approach, which combined hydrogen-deuterium exchange (HDX), quantitative protein-protein and protein-nucleic acid cross-linking (XL), and homology analysis, to model the structure of the complex between the full-length DNA binding domain (DBD) of FOXO4 and its DNA binding element (DBE). The results confirmed that FOXO4-DBD assumes the characteristic forkhead topology shared by these types of transcription factors, but its binding mode differs significantly from those of other members of the family. The results showed that the binding interaction stabilized regions that were rather flexible and disordered in the unbound form. Surprisingly, the conformational effects were not limited only to the interface between bound components but extended also to distal regions that may be essential to recruiting additional factors to the transcription machinery. In addition to providing valuable new insights into the binding mechanism, this project provided an excellent evaluation of the merits of structural proteomics approaches in the investigation of systems that arematerial not directly amenable to traditional high-resolution techniques.

With the development of salt cavern gas storage construction technology, the construction of large-scale gas storage salt caverns using sediment voids is expected to solve the problem of low effective volume formation rate and poor construction economy of high-impurity salt mines. There are few studies on the long-term operation mechanical behavior of salt cavern gas storage under the influence of sediment accumulation currently. This paper studies the influence of sediment accumulation height, particle gradation, and operating pressure on the stability of salt caverns by constructing a coupling model of sediment particle discontinuous medium and surrounding rock continuous medium. The continuous-discontinuous coupling algorithm is suitable for analyzing the influence of particle accumulation height and particle gradation on the creep shrinkage of salt caverns. The increase of sediment accumulation height slows down the creep shrinkage of the bottom of the salt cavern, strengthens the restraining effect on the surrounding rock of the cavern, and moves the position of the maximum displacement of the surrounding rock to the upper part of the cavern; the sediment particle gradation has little effect on the cavern volume shrinkage rate, and the greater the coarse particle content, the smaller the cavern volume shrinkage rate; the greater the operating pressure, the more conducive to maintaining the stability of the cavern, slowing down the upward movement of the sediment body and increasing the gas storage space in the upper part of the cavern. This research results can provide a reference for evaluating the long-term operation stability of sediment-type high-impurity salt cavern gas storage.

Addressing escalating energy demands and greenhouse gas emissions in the oil and gas industry has driven extensive efforts in carbon capture and utilization (CCU), focusing on power plants and industrial facilities. Utilizing CO2 as a primary feedstock for industrial fuels and petrochemical materials offers a favorable alternative to sequestration, with byproducts substituting traditional chemical feedstocks. This comprehensive review explores the current landscape of CO2 capture technologies, examining opportunities, economic viability, and efficiency challenges. It provides a detailed analysis of various CO2 utilization methods and the combined process of capture and utilization. The review highlights primary obstacles in planning, production, and widespread implementation, emphasizing the need for strategic integration of materials research, process performance, and cost-effectiveness to advance new technologies.

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 stimulates the scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical used by millions of tons in the last 50 years worldwide to drying weeds in cultivated fields, greenhouses, roadsides. Concern has been raised in many quarters about the possible presence in the food chain and the consequent adverse effects on health: both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are here discussed. The great debate that has been generated requires further investigations and field measurements to understand its fate once dispersed in the environment and its concentration in the food chain. Hence the need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in any detail, including cleanup, derivatization, and instrumental conditions to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS but sufficient indications are also given to those laboratories that wish to use the simpler HPLC-FLD, HPLC-UV, GC-NPD or GC-FPD techniques for screening purposes. Concentrations from literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported together with the regulatory status in various parts of the world and the accumulation mechanism. As for the accumulation in cereals, available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration) and that in cold climates the herbicide tends to persist in the soil for a long time.

In recent years, machine learning (ML) techniques have emerged as an efficient and effective technology within the petroleum industry. This paper focuses on the current application of ML in enhanced oil recovery (EOR) through CO2 injection, which exhibits promising economic and environmental benefits of climate-change mitigation strategy. Our comprehensive review explores the diverse use cases of ML techniques in CO2-EOR, including aspects such as minimum miscible pressure (MMP) prediction, well location optimization, oil production and recovery factor prediction, multi-objective optimization, Pressure-Volume-Temperature (PVT) properties estimation, Water Alternating Gas (WAG) analysis, and CO2-foam EOR, from 101 reviewed papers. In this comprehensive review, we catalog relative information, including the input parameters, objectives, data sources, train/test/validate information, results, evaluation, and rating score for each area based on criteria such as data quality, ML building process, and analysis of results. We also briefly summarized the benefits and limitations of ML methods in petroleum industry applications. Our detailed and extensive study could serve as an invaluable reference for employing ML techniques in the petroleum industry. Based on the review, we found that ML techniques offer great potential in solving problems in the majority of CO2-EOR areas involving prediction and regression. With the generation of massive amounts of data in the everyday oil and gas industry, machine learning techniques can provide efficient and reliable preliminary results for the industry.

Based on the theory that certain geological fault zones surpass the influence of other abiotic and biotic site factors for mound-building red wood ants (Formica rufa group), an area northwest of Tuttlingen with extremely high ant density was systematically surveyed, taking into account official geological maps. Indicators of active fault zones were recorded. These were additionally examined in a model area using a high-resolution digital terrain model (DTM 1-meter). The study area is located in the Swabian Jura at the western edge of the Albstadt shear zone, where recent seismic activity is documented by frequent earthquakes. The earthquakes are considered to be the cause of gas permeability in the strike-slip faults, around which the clustered nesting sites were mapped. More than 2900 nests of the Formica rufa group were mapped and their site conditions analysed in different geomorphological positions. In addition to recording forestry site conditions, a geological classification was carried out, as well as an analysis of soil gases/mofettes in areas with the highest nest densities. The correlation between forestry data and nest sites did not reveal a consistent pattern. In contrast, the relationships with gas-permeable strike-slip faults, though predominantly covered with Quaternary sediments, could be identified through CO₂- and CH₄-rich gas emissions, mofettes, and doline features. The interpretations were complicated due to different mapping ages and signatures of the geological maps. Fortunately, this issue could be analysed and evaluated in a sub-area with mappings from 1936/71 and 1995 regarding presumed or confirmed fault trajectories. New insights were gained regarding the relationships between Formica nest sites, gas-permeable faults, and groundwater levels on narrow mountain ridges with steep relief. Here, the lateral emission of CO₂ depends on the groundwater level and does not occur vertically directly above the fault. C- and H-isotope data of CO₂ and CH₄ do not show a consistent source. While methane is mainly derived from biological production by Archaea in the upper crust and in swamp areas, CO₂ mostly originates from the mantle. The results of the investigations revealed that a multitude of geological and ecological factors must be considered for the interpretation of the occurrences of Formica sites northwest of Tuttlingen. These factors confer a distinct originality to this region, contributing not only to an enhanced understanding of site conditions but also furnishing information regarding environmentally relevant gas emissions.

An approach based on the OpenFOAM library has been developed to solve a high-speed, multicomponent mixture of a reacting, compressible flow. This work presents comprehensive validation of the newly developed solver called compressibleCentralReactingFoam with different supersonic flows, including shocks, expansion waves, and turbulence-combustion interaction. The comparisons of the simulation results with experimental and computational data confirm the fidelity of this solver for problems involving multicomponent high-speed reactive flows. The gas dynamics of turbulence-chemistry interaction are modeled using a partially-stirred reactor formulation and provide promising results to better understand the complex physics involved in supersonic combustors. A time-scale analysis based on local Damköhler numbers reveals different regimes of turbulent combustion. In the core of the jet flow, the Damköhler number is relatively high indicating that the reaction time scale is smaller than the turbulent mixing time scale. This means that the combustion is controlled by turbulent mixing. In the shear layer, where the heat release rate and the scalar dissipation rate have the highest value, the flame is stabilized due to finite rate chemistry with small Damköhler numbers and a high fraction of fine structure. This solver allows three-dimensional gas dynamic simulation of high-speed multicomponent reactive flows relevant to practical combustion applications.

We propose a correspondence between partition functions of ideal gases consisting of both bosons and fermions and algebraic bases of supersymmetric polynomials on the Banach space of absolutely summable two-sides sequences ℓ1(Z0). Such an approach allows us to interpret some combinatorial identities for supersymmetric polynomials from a physical point of view. We consider a relation of equivalence on ℓ1(Z0) induced by the supersymmetric polynomials, and semiring algebraic structures on the quotient set with respect to this relation. The quotient set is a natural model for the set of energy levels of a quantum system. We introduce two different topological semiring structures on this set and discuss their possible physical interpretations.

Nigeria's upstream oil and gas sector is extensively contributing to the economic growth of the country, but the sector is plagued with challenges around corporate social responsibility (CSR) and taxation practices. Petroleum Industry Act (PIA) is introduced to tackle these challenges towards promoting sustainable development in Nigeria. The aim of this study is to explore the PIA’s provisions on CSR and taxation, identify the Act’s implementation challenges and improvement opportunities, propose an integrated framework for monitoring and evaluating the PIA’s impact on CSR and taxation over time, and recommend measures for enhancing PIA’s impact on CSR and taxation support for sustainable development in Nigeria's upstream oil and gas sector. This study adopts the qualitative desk review method to analyze existent literature, reports, and documents regarding PIA’s provisions on CSR and taxation. Findings reveal that the PIA’s provisions greatly emphasize CSR initiatives and taxation transparency in improving responsible ethical business behaviour. An integrated framework for monitoring and evaluating PIA’s impact over time is developed. This study concludes that the PIA's provisions can balance CSR and taxation practices for sustainable development. The study’s recommendations include using the integrated framework as a structured strategy for monitoring and evaluating the PIA’s impact. This study contributes to the discussion on the imperatives of ethical business practices and regulatory frameworks for sustainable development drive in the oil and gas sector.

Blood gas analysis plays a central role in modern medicine. Advances in technology have expanded the range of available parameters and increased the complexity of their interpretation. By applying user-centered design principles, it is possible to reduce the cognitive load associated with interpreting blood gas analysis. In this international, multicenter study, we explored anesthesiologists' perspectives on Visual Blood, a novel visualization technique for presenting blood gas analysis results. We conducted interviews with participants following two computer-based simulation studies: the first utilizing Virtual Reality (VR) (50 participants) and the second without VR (70 participants). Employing the template approach, we identified key themes in the interview responses and formulated six statements, which were rated using Likert scales: from 1 (strongly disagree) to 5 (strongly agree) in an online questionnaire. The most frequently mentioned theme was the positive usability features of Visual Blood. The online survey revealed that participants found Visual Blood to be an intuitive method for interpreting blood gas analysis (median 4, IQR 4-4, p<0.001). Participants noted that minimal training was required to effectively learn how to interpret Visual Blood (median 4, IQR 4-4, p<0.001). However, adjustments are necessary to reduce visual overload (median 4, IQR 2-4, p<0.001). Overall, Visual Blood received a favorable response. The strengths and weaknesses derived from these data will help optimize future versions of Visual Blood to improve the presentation of blood gas analysis results.

In order to harmonize supply and demand of green energy, new future-proof technologies are needed. Here, hydrogen plays a key role. Within the current framework conditions, the production of green hydrogen is not yet economically viable. The use of the oxygen produced and the possible increase in efficiency associated with it mostly remains unconsidered. The aim is to demonstrate that the economic efficiency of a power-to-gas (PtG) project can be increased by using the by-product oxygen. In this research project, a water electrolyser connected to grid is powered to supply hydrogen to a hydrogen refuelling station. By utilising the by-product oxygen from water electrolysis for a wastewater treatment plant (WWTP), it is shown that the net present value (NPV) of the project can be improved by up to 13 % compared to the initial scenario. If a photovoltaic (PV) system is used in addition to grid electricity for higher green hydrogen production, the NPV can be further improved by up to 58 %. The levelized cost of hydrogen (LCOH) is calculated for different scenarios with and without oxygen configuration. A sensitivity analysis is then performed to find important parameters.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

The influence of distant London dispersion forces on the docking preference of alcohols of different size between the two lone electron pairs of the carbonyl group in pinacolone is explored by infrared spectroscopy of the OH stretching fundamental in supersonic jet expansions of 1:1 solvate complexes. Experimentally, no pronounced tendency of the alcohol to switch from the methyl to the bulkier tert-butyl side with increasing size is found. In all cases, methyl docking dominates by at least a factor of two, whereas DFT-optimized structures suggest a very close balance for the larger alcohols, once corrected by CCSD(T) relative electronic energies. Together with inconsistencies when switching from a C4 to a C5 alcohol, this points at deficiencies of the investigated B3LYP and in particular TPSS functionals even after dispersion correction, which cannot be blamed on zero point energy effects. The search for density functionals which describe the harmonic frequency shift, the structural change and the energy difference between the docking isomers of larger alcohols to unsymmetric ketones in a satisfactory way is open.