Interleaved power factor correction (PFC) is widely used circuit topology due to good efficiency and power density for single-switch boost PFC. As the differential mode (DM) electromagnetic interference (EMI) noise magnitude depends upon the input current ripple, this research details a comprehensive study of DM EMI filter design for interleaved boost PFC with the aim of minimizing the component size. It is also demonstrated that the different numbers of interleaved stages and switching frequency influence the filter attenuation requirement and, thus, the EMI filter size. First, an analytical model is derived on the basis of the Norton equivalent circuit model for the differential mode noises of interleaved boost PFC within the frequency range of 9-500 kHz. The derived model can help identify the optimal phase shifting among the interleaved boost converters in order to minimize the considered differential mode noises at the filter design frequency. So, a novel phase-shift method is developed to get a minimized attenuation required by a filter in Band B. Further, a volume optimization of the required DM filter was introduced based on the calculated filter attenuation and volumetric component parameters. Based on the obtained results, unconventional and conventional phase shifts have demonstrated a good performance in decreasing the EMI filter volume in Band B and Band A, respectively. A 2-kW interleaved PFC case study is presented to verify the theoretical analyses and the impact of phase-shifting on EMI filter size.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

Despite the successes earned in cataloguing and finding the role of the most of molecular components in living matter, the “biochemical and molecular” perspective, popular in biology, medicine and genetics, is unable to give account for crucial topics as the faculty of living systems to “feel”, to “perceive” what a given stimulus implies (means, indeed) for their survival. Condensed matter physics too, if bounded to a local, short-range, and perturbative approach, fails dramatically. This is also due to the role commonly assigned to water – actually the main constituent of living matter – deemed for long time to be merely chemical (as “solvent” or a reactant/product). Nonetheless, today many evidences show how living matter can be right conceived as a super-structured coherent water-based matrix, suggesting that the characterization of bio(electro)chemical and physical processes undertaken at molecular level in living matter, would let us unable to answer a question like this: what allows an amoeba, moreover without any neurons, to “know” to get closer to a nutrient or escape away from a toxin? I propose that to pursue such a fundamental inquiry it’s necessary an essentially relational approach, that is: to consider the living being at its grounding as the outcome of a physical history of relationships where symmetry-breakings, dissipation and coherence yield the emergence of the living state of matter, conceivable only as a time-dependent open process, and not as a portraited “body”. The effective tools to build up such an approach may be retrieved in far-from-equilibrium thermodynamics (TD), symmetry-breakings and gauge-fields theory, science of complexity, within the framework of a Quantum Field Theory. Indeed, within a field-view of matter, and of water especially, as it has been developed by a Quantum Electrodynamic (QED) description of condensed matter, it’s possible to give account for a physical basis too such an epistemologically elusive, though crucial, feature of living systems (i.e.: perception and meaning). The emerging landscape allows some important meditations about adaptation, evolution, ecodynamics, and about different conceptions of complexity and “information” in living realm. Furthermore, some neuroscientific themes like consciousness, qualia and their links to artificial intelligence could be supplied with due insights.

Complex dynamical fluctuations, from molecular noise within cells, collective intelligence, brain dynamics or computer traffic have been shown to display noisy behaviour consistent with a critical state between order and disorder. Living close to the critical point can have a number of adaptive advantages and it has been conjectured that evolution could select (and even tend to) these critical states. One way of approaching such state is by means of so-called self-organized criticality (SOC) where the system poises itself close to the critical point. Is this the case of living cells? It is difficult to test this idea given the enormous dimensionality associated with gene and metabolic webs. In this paper, we present an alternative approach: to engineer synthetic gene networks displaying SOC behaviour. This is achieved by exploiting the presence of a saturation (congestion) phenomenon of the ClpXP protein degradation machinery in E. coli cells. Using a feedback design that detects and then reduces ClpXP congestion, a {\em critical motif} is built from a two-gene network system, where SOC can be successfully implemented. Both deterministic and stochastic models are used, consistently supporting the presence of criticality in intracellular traffic. The potential implications for both cellular dynamics and designed intracellular noise are discussed.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

In the application of classical nucleation theory (CNT) and all other theoretical models of crystallization of liquids and glasses it is always assumed that nucleation proceeds only after the supercooled liquid or the glass have completed structural relaxation processes towards the metastable equilibrium state. Only employing such assumption, the thermodynamic driving force of crystallization and the surface tension can be determined in the way it is commonly performed. The present paper is devoted to the theoretical treatment of a different situation when nucleation proceeds concomitantly with structural relaxation. To treat the nucleation kinetics theoretically for such cases, we need adequate expressions for the thermodynamic driving force and the surface tension accounting for the contributions caused by the deviation of the supercooled liquid from metastable equilibrium. In the present paper, such relations are derived. They are expressed via deviations of structural order parameters from their equilibrium values. Relaxation processes result in changes of the structural order parameters with time. As a consequence, the thermodynamic driving force and surface tension, and basic characteristics of crystal nucleation, such as the work of critical cluster formation and the steady-state nucleation rate, also become time-dependent. We show that this scenario may be realized in the vicinity and below the glass transition temperature, and it may occur only if diffusion (controlling nucleation) and viscosity (controlling the alpha-relaxation process) in the liquid decouple. Analytical estimates are illustrated and confirmed by numerical computations for a model system. The theory is successfully applied to the interpretation of experimental data. Several further consequences of this newly developed theoretical treatment are discussed in detail. In line with our previous investigations, we reconfirm that only when the characteristic times of structural relaxation are of similar order of magnitude or longer than the characteristic times of crystal nucleation, elastic stresses evolving in nucleation may significantly affect this process. Completing the analysis of elastic stress effects, for the first time expressions are derived for the dependence of the surface tension of critical crystallites on elastic stresses. As the result, a comprehensive theoretical description of crystal nucleation accounting appropriately for the effects of deviations of the liquid from the metastable states and of relaxation on crystal nucleation of glass-forming liquids, including the effect of simultaneous stress evolution and stress relaxation on nucleation, is now available. As one if its applications, this theoretical treatment provides a new tool for the explanation of the low-temperature anomaly in nucleation in silicate and polymer glasses (the so-called \breakdown" of CNT at temperatures below the temperature of the maximum steady-state nucleation rate). We show that this anomaly results from much more complex features of crystal nucleation in glasses caused by deviations from metastable equilibrium (resulting in changes of the thermodynamic driving force, the surface tension, and the work of critical cluster formation, in the necessity to account of structural relaxation and stress effects) than assumed so far.

In this paper, we found new classes of exact models to the Einstein-Maxwell system of equations which describe the internal structure of a compact star made of strange matter considering the equation of state proposed by Rocha, Bernardo, de Avellar and Horvath in 2019. It has been assumed that this matter is composed of equal number of up, down and strange quarks and a small amount of electrons required to reaching the charge neutrality. If this hypothesis is correct, the neutron stars could be strange stars or hybrid stars with a thin crust of nuclei where the temperatures and pressures are capable of converting hadronic matter into this new stable phase of quarks. We have chosen a particular form of gravitational potential Z(x) that depends on an adjustable parameter related to degree of anisotropy of the models and the new solutions can be written in terms of elementary and polynomial functions. The obtained models satisfy all physical features expected in a realistic star and the expressions for mass, density and stellar radius are comparable with the experimental results.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

Pharmaceuticals contain biologically active components that can pollute water courses as a result of the excretions from individuals and/or uncontrolled release of residues from chemical plants, and they can pose a hazard to health. Pharmaceutical residues can persist at low concentrations in the environment, and thus may be potentially harmful to aquatic animals and to humans. Controlling and monitoring such residues are therefore a prime interest, for example, a solid-phase extraction uses solid sorbents to purify and preconcentrate the residues prior to their chemical analysis. In the present study, poly (acrylonitrile-co-divinylbenzene-80) sorbents are synthesised by varying the comonomer feed ratios under precipitation polymerisation conditions to deliver a family of porous polymer microspheres. Acrylonitrile confers polar characters onto the sorbents, and the acrylonitrile-derived nitrile groups can be chemically transformed via polymer-analogous reactions into thioamide and sulfonated residues which make the sorbents even more suitable for the capture of polar analytes, including selected pharmaceuticals. The utility of the porous thioamide-sulfonated containing sorbents is demonstrated via the dispersion-solid phase extraction of mefenamic acid from aqueous media; mefenamic acid is an anthranilic acid derivative which is a potent, non-steroidal anti-inflammatory drug which is found in environmental waters at low concentrations.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

Knowing, with reasonable accuracy, the dry matter (DM) content of Hass avocado fruit will help determine when the fruit must be harvested. The reliability of predictive models based on near infrared spectra for DM quantification depends on the ability of the spectra to be representative of the DM gradient within a whole fruit. The aim of this work was to develop a methodology to determine the optimum number of spectra to develop a robust model for DM content quantification. Three spectra were recorded for each zone of the intact fruit: peduncle, equator, and base. Each scanning point was sampled, and the DM content was determined using oven drying. Two-way ANOVA confirmed the DM gradient within the whole fruit. This gradient was observed within spectra using the RMS (root mean square) criterion and PCA. The PLS models showed that at least one spectrum per zone could be enough to construct an efficient and robust model for dry matter quantification.

Downward short-wave (SW) solar radiation is the only essential energy source powering the atmospheric dynamics, ocean dynamics, biochemical processes, etc. on our planet. Clouds are the main factor limiting the SW flux over the land and the Ocean. For the accurate meteorological measurements of the SW flux one needs expensive equipment - pyranometers. For some cases where one does not need golden-standard quality of measurements, we propose estimating incoming SW radiation flux using all-sky optical RGB imagery which is assumed to incapsulate the whole information about the SW flux. We used DASIO all-sky imagery dataset with corresponding SW downward radiation flux measurements registered by an accurate pyranometer. The dataset has been collected in various regions of the World Ocean during several marine campaigns from 2014 to 2022, and it will be updated. We demonstrate the capabilities of several machine learning models in this problem, which are multilinear regression, Random Forests, Gradient Boosting and convolutional neural networks (CNN). We also applied the inverse target frequency (ITF) re-weighting of the training subset and the approach of pre-classification in order to raise the SW flux approximation quality. We found that the CNN is capable of approximating downward SW solar radiation with higher accuracy compared to existing empiric parameterizations. We also found that the ITF reweighting of the training subset increases the approximation quality substantially. The estimates of the SW radiation flux using all-sky imagery may be of particular use in case of the need for the fast radiative budgets assessment of a site.

The fatigue life of welded joints under cyclic loading is a complex process that can be roughly divided into fatigue crack initiation, crack propagation and final fracture. Usually, these phases are evaluated separately. Several methods are available to estimate the extent of the different phases in welded components, such as stress-based fatigue concepts for crack initiation or linear elastic fracture mechanics for crack propagation; however, distinguishing these phases in welded components is a complex procedure and often relies on assumptions such as transition crack sizes. The objective of this study is to investigate the relationship between fatigue crack initiation and propagation in welded joints using artificially notched specimens with welded joints characteristics of different notch acuity (different radii and opening angle). The experiments show that the investigated relationship basically depends on the notch acuity, the load level and the stress ratio.

Essential oils (EOs) have been gaining popularity in the past decades among researchers due to their potential to replace conventional chemicals used in the fight against pests, pathogenic and spoilage microbes and oxidation processes. EOs are complex mixtures with many chemical components the content of which depends on many factors – not just the plant genus, species or subspecies, but also chemotype, locality and climatic conditions, phase of vegetation, method of extraction and others. Due to this fact, there’s still much to study, with antimicrobial effect being one of the key properties of EOs. There are many methods that have been frequently engaged by researchers for in vitro evaluation; however, although the research has been going on for decades, an internationally accepted standard is still missing. Most of methods are based on time-proven standards used for testing of antibiotics. Due to the specific properties of EOs and their components, such as volatility and hydrophobicity, many modifications of these standard procedures have been adopted. The aim of this review is to describe the most common methods and their modifications for testing of antimicrobial properties of EOs and to point out the most controversial variables which can potentially affect results of the assays.

Based on the two-flavors Polyakov quark-meson model, we study the bubble dynamics of a first-order phase transition in chiral phase diagram at high density but low temperature in the framework of the homogeneous thermal nucleation theory. Under the mean-field approximation, after obtaining the effective potential with inclusion of the fermionic vacuum term, we build a geometric approach to probe two possibly existing minima, which can actually tunnel through a bounce interpolated between a metastable vacuum to an adjacent true vacuum. By separating our discussions into a weak first-order hadron quark phase transition and strong ones, the bubble profiles, the surface tension, the typical radius of the bounce and the saddle point action in the presence of a nucleation bubble as a function of temperature are numerically calculated in detail as the chemical potentials are fixed at $\mu=306 \mathrm{MeV}$ and $\mu=310 \mathrm{MeV}$. our results show that the surface tension remains a small value even when the density is very high and phase boundaries for hadron and quark matter should be resized properly according to the saddle point action evaluated on the bounce. It is also noticed that the inclusion of the deconfinement phase transition in term of the Polyakov loop does not change chiral phase transition dramatically for light quarks.

To overcome the time-consuming drawbacks of Computational Fluid Dynamics (CFD) numerical simulations, this paper proposes a hybrid model based on a parallel architecture based on the concept of intelligent aerodynamics, named PA-TLA (Parallel Architecture combining TCN, LSTM, and Attention mechanism). This model utilizes CFD data to drive efficient predictions of aircraft wake evolution at different initial altitudes during the approach phase. Initially, CFD simulations of continuous initial altitudes during the approach phase are used to generate aircraft wake evolution data, which are then validated against real-world LIDAR data to verify their reliability. The PA-TLA model is designed based on a parallel architecture, combining Long Short-Term Memory networks (LSTM), Temporal Convolutional Networks (TCN), and a tensor concatenation module based on the attention mechanism, which ensures computational efficiency while fully leveraging the advantages of each component in a parallel processing framework. The study results show that the PA-TLA model outperforms both the LSTM and TCN models in predicting the three characteristic parameters of aircraft wake: vorticity, circulation, and Q-criterion. Compared to the serially structured TCN-LSTM, PA-TLA achieves an average reduction in mean squared error (MSE) by 6.80%, mean absolute error (MAE) by 7.70%, and root mean square error (RMSE) by 4.47%, with an average increase in the coefficient of determination (R²) by 0.36%, and a 35% improvement in prediction efficiency. Lastly, this study combines numerical simulation and the PA-TLA deep learning architecture to analyze the characteristics of wake evolution during the near-ground phase, providing theoretical value for further reducing aircraft wake intervals and enhancing airport operational efficiency.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Permafrost covers about 23% ~ 25% of the land in the northern hemisphere, mainly in Russia, Canada, Alaska, Northeast and Qinghai Tibet Plateau (QTP) in China. Many engineering especially the transportation has been in the permafrost regions above. Under the action of highways construction and global warming, permafrost under infrastructures is degraded and causes serious damage. Two phases closed thermosyphon (TPCT) is a widely accepted green countermeasure against the problem in permafrost regions. Although it has been applied to prevent permafrost degradation, their application presents significant challenges on account of the stronger endothermic action of asphalt pavement. This paper focused on the thermosyphon technology and application in the permafrost. Moreover, the article highlighted the excellent working performance of the TPCT that improving the stability of the infrastructures and prevent it degrading due its excellent efficiency of heat transfer. The industrial applications of the TPCT were also summarized, along with their limitations. Finally, the results reported in this paper can provide a valuable guidance for the design of the TPCT and construction of the permafrost regions in the future.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Femtoscopy is a unique tool to investigate the space-time geometry of the matter created in ultra-relativistic collisions. If the probability density distribution of hadron emission is parametrized, then the dependence of its parameters on particle momentum, collision energy, and collision geometry can be given. In recent years, several measurements came to light that indicated the adequacy of assuming a Lévy-stable shape for the mentioned distribution. In parallel, several new phenomenological developments appeared, aiding the interpretation of the experimental results, or providing tools for the measurements. In this paper we review and discuss some of these advances, phenomenological and experimental.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

The mechanism of vapor-gas deposition of vinyltrimethoxysilane (VS) and ethylene glycol (EG) from azeotropic solutions is investigated, which allows to reduce the evaporation temperature of the components of working mixtures. The need for such studies is associated with the development of a new direction in the technology of vapor-gas deposition of polymer coatings. Methods have been developed for monitoring the chemical composition of working solutions in evaporators using optical spectroscopy, which allow calculating the partial pressures of vapor phase components. Based on these studies, compositions of working solutions are proposed that allow to equalize the partial pressures of the components of working mixtures with a large difference in boiling point. A new method of vapor-gas deposition of non-volatile powder inhibitors on metals is proposed. Chemical compositions of siloxane coatings were determined using XPS and mechanisms of interaction of VS with polymerization promoters ethylene glycol and 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP) were proposed.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Applying of blood biopolymers to regulate the phase composition is promising in designing the hydroxyapatite-based hybrid biomaterials with controllable resorbability. Hybrid materials based on hydroxyapatite and platelet-poor plasma (PPP) were formed in conditions of chemical precipi-tation at pH 11, [Ca2+] / [PO43–] ratio 1.67, PPP volume fraction of 6–24%, maturing time of 4–9 days. Mineral component of the materials was represented as 53% hydroxyapatite / 47% amor-phous calcium phosphate after 4 days of maturation, and 100% hydroxyapatite after 9 days of maturation. Varying PPP content from 6% to 24% provided forming of materials with rather de-fined content of amorphous calcium phosphate and biopolymer component, having desired mor-phology ranging from typical apatitic conglomerates to hybrid apatite-biopolymer fibers. Co-precipitated hybrid materials based on hydroxyapatite and PPP are promising for bone regen-eration in osteoplastic and maxillofacial applications.

Magnetic nanoparticles (MNPs) have attracted a great interest in nanomedical research. MNPs exhibit many important properties, particularly, magnetic hyperthermia for selective killing of cancer cells is one of them. In hyperthermia treatment, MNPs act as nano-heaters when they are under the influence of an alternating magnetic field (AMF). In this work, micromagnetic simulations have been used to investigate the magnetization dynamics of a single-domain nanoparticle of magnetite in an external AMF. Special attention is paid to the circumstances dealing with a dynamic phase transition (DPT). Besides, we focus on the influence of the orientation of the magnetic easy-axis of the MNP on the dynamic magnetic properties. For amplitudes of the external AMF above certain critical value, the system is not able to follow the magnetic field and it is found in a dynamically ordered phase; whereas for larger amplitudes, the state corresponds to a dynamically disordered phase and the magnetization follows the external AMF. Our results suggest that the way how the order-disorder DPT takes place, and both the metastable lifetime as well as the specific loss power (SLP), are strongly dependent on the interplay between the orientation of the magnetic easy-axis and the amplitude of the external AMF.

The analogy between the theory of phase transitions in simple fluids and vehicular traffic flow has long been suspected, promising a new level of understanding of urban congestion by standing on one of the firmer foundations in physics. The obstacle has been the interpretation of the thermal energy of the gas-particle system, which remains unknown. This paper proposes the flow of cars through the network as a viable interpretation, where the fundamental diagram for traffic flow would be analogous to the coexistence curve in gas-liquid phase transitions. Thanks to the power-law form of the coexistence curve, it was possible to formalize that the resulting network traffic model belongs to the Kardar-Parisi-Zhang universality class. The scaling relationships arising in this universality class are found to be consistent with West's scaling theory for cities. It is shown that congestion costs (delays + fuel consumption) scale superlinearly with city population, possibly and worryingly more so than predicted by West's theory. Implications for sustainability and resiliency are discussed.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

From the formalism of the thermodynamics of irreversible processes and the theory of complex systems, characterization of longevity and aging and its relationship with the emergence and evolution of cancer was carried out. It was found that: 1. The rate of entropy production can be used as an index of robustness, plasticity, the aggressiveness of cancer, and as a measure of biological age; 2. The aging process, as well as the evolution of cancer, goes through what we have called “biological phase transition”; 3. The process of metastasis, which occurs through epithelial-mesenchymal transition (EMT), appears as a phase transition far from thermodynamic equilibrium and exhibits Shilnikov chaos-like dynamic behavior. This dynamic guarantees the robustness of the process and, in turn, its unpredictability; 4. It was shown that as the ferroptosis process is strengthened, the complexity of the dynamics associated with the emergence and evolution of cancer decreases. The theoretical framework developed contributes to a better understanding of the biophysical-chemical phenomena of longevity and aging and their relationship with cancer.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

In the context of all-digital radar systems, phase-modulated continuous wave (PMCW) based on pseudorandom binary sequences (PRBSs) appears a prominent candidate modulation scheme for applications such as autonomous driving. Among the reasons for that are its simplified transmitter architecture and lower linearity requirements, e.g., compared to orthogonal-frequency division multiplexing radars, as well as its high velocity unambiguity and multiple-input multiple-output operation capability that are characteristic of digital radars. For appropriate operation of a PMCW radar, choosing a PRBS whose periodic autocorrelation function (PACF) has low sidelobes and high robustness to Doppler shifts is paramount. In this sense, this article performs an analysis of Doppler shift tolerance of the PACFs of typically adopted PRBSs in PMCW radar systems supported by simulation and measurement results. To accurately measure the Doppler-shift-induced degradation of PACFs, peak power loss ratio (PPLR), peak sidelobe level ratio (PSLR), and integrated-sidelobe level ratio (ISLR) were used as metrics. Furthermore, to account for effects on targets whose ranges are not multiples of the range resolution, oversampled PACFs are analyzed.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD &lt; 2%) and core size (%RSD &lt; 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

How does the human neurophysiological system self-organize to achieve optimal phase relationships among joints and limbs, such as in the composite rhythms of butterfly and front crawl swimming, drumming, or dancing? We conducted a systematic review of literature relating to CNS control of phase among joint/limbs in continuous rhythmic activities. SCOPUS and Web of Science were searched using keywords ‘Phase AND Rhythm AND Coordination’. This yielded 998 matches from which 23 papers were extracted for inclusion based on screening criteria. The empirical evidence arising from in-vivo, fictive, in-vitro, and modelling of neural control in humans, other species, and robots indicates that the control of movement is facilitated and simplified by innervating muscle synergies by way of spinal central pattern generators (CPGs). These typically behave like oscillators enabling stable repetition across cycles of movements. This approach provides a foundation to guide the design of empirical research in human swimming and other limb independent activities. For example, future research could be conducted to explore whether the two-layer CPG model proposed by Saltiel et al [1] to explain locomotion in cats might also explain the complex relationships among the cyclical motions in human swimming.

We investigate a notable class of states peculiar to a bosonic binary mixture featuring repulsive intraspecies and attractive interspecies couplings. We evidence that, for small values of the hopping amplitudes, one can access particular regimes marked by the fact that the interwell boson transfer occurs in a jerky fashion. This property is shown to be responsible for the emergence of a staircase-like structure in the phase diagram and to strongly resemble the mechanism of the superfluid-Mott insulator transition. Under certain conditions, in fact, we show that it is possible to interpret the interspecies attraction as an effective chemical potential and the supermixed soliton as an effective particle reservoir. Our investigation is developed both within a fully quantum approach based on the analysis of several quantum indicators and by means of a simple analytical approximation scheme capable of capturing the essential features of this ultraquantum effect.

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

This work intends to present a study on relations between a Lie algebra called dispersion operators algebra, linear canonical transformation and a phase space representation of quantum mechanics that we have introduced and studied in previous works. The paper begins with a brief recall of our previous works followed by the description of the dispersion operators algebra which is performed in the framework of the phase space representation. Then, linear canonical transformations are introduced and linked with this algebra. A multidimensional generalization of the obtained results is given.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

Thunderstorm electrification has been studied for hundreds of years. Several mechanisms have been proposed to elucidate the electrification, including convective charging, inductive precipitation charging, and ice crystal-graupel collision charging. Field observations and model studies have demonstrated the vital roles that graupel and ice crystals play in the electrification, but the mechanism of the collision charging is still unclear. The fundamental essence of relative growth rate theory used for explaining the tripole charge structure in thunderclouds also needs a further exploration. We analyze the processes of ice crystal-graupel collision charging from charge migration inside hydrometeors to charge separation between two hydrometeors. The driving effects of temperature gradient and chemical potential gradient in charge migration are clarified, as well as the applicability of the relative growth rate theory, thermoelectric effect and surface tension gradient in different humidities. Based on the understanding from these electrification mechanisms, we propose that the essence of charge separation is driven by non-thermal equilibrium, and future studies on thunderstorm electrification should focus on the dynamical non-thermal equilibrium of cloud particles.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Bimetallic colloidal CoPt nanoalloys, with a very low platinum content, were successfully synthesized following a modified polyol approach. Powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis, and Transmission Electron Microscopy studies were performed to estimate the crystal structure, morphology and surface functionalization of the colloids respectively, while the room temperature magnetic properties were measured using Vibrating Sample Magnetometer. The particles exhibit excellent uniformity, with a narrow size distribution, and display strong room temperature hysteretic ferromagnetic behavior even in the as-made form. Upon annealing at elevated temperatures, progressive formation and co-existence of exchange coupled both chemically ordered and disordered phases, significantly enhance the room temperature coercivity.

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being utilized for growing different cell types in vitro, their pH and its effect, together with the crosslinking ions, of those formulations are still infrequently assessed. In this work we studied how these elements can affect hydrogel stability and printability and influence U2OS and NIH/3T3 cell viability and metabolism on the resulting 3D prints. In this context, 6% alginate + 2% gelatin hydrogels were prepared with 0.1 M MES buffer with pH 5.5, 6.5, 7.0 or 8.0, printed by extrusion-based 3D printing, and crosslinked immediately after printing with either CaCl2 or BaCl2. Our results showed that both the buffer pH and the crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of the prints. Moreover, the buffer pH influenced the printability of the hydrogel in air, but when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. Besides, Ba2+ increased cell death of NIH/3T3 cells while had no effect on the U2OS cell viability. The pH of the buffer also caused an important impact on the cell behaviour. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5. Whereas, NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference on cell arrangement of the U2OS cells growing on prints prepared from hydrogels with acidic buffer in comparison to cells growing on those prepared using neutral or basic buffer. These results show that both pH and crosslinking ion influence hydrogel strength and cell behaviour.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Abstract: Self-regulated Learning has become one of educational psychology's most critical research areas. Contemporary research indicates that student creativity is crucial to the success of arts education. However, there is limited research on creativity in arts education in Self-regulated Learning. Therefore, this study aims to define the creativity characteristics that determine the quality of students’ work. This study implemented a creative competition in painting and composition for first-year undergraduates. It evaluated the characteristics of creativity during the three main phases of the task: planning, execution, and completion. We discovered through semi-open questionnaires (n=178)，and using the content analysis method. According to the competition results, the students with the highest scores in Flow, Inspiration, and Idea Generation in the Performance phase had the best quality work. In the Forethought phase, Analogical Thinking and Idea Generation worked best for most students, while in the Performance phase, Flow Sense, Idea Generation, and Idea Manipulation worked best.Data on creativity characteristics at different work phases and final quality might adequately guide and organize educational procedures. These findings can serve as a theoretical foundation for quantifying the creativity phase in Self-regulated Learning and offer arts educators a reference for creativity instruction.

An exact solution for the Nagel-Schreckenberg model for v_max = 1 is known since the 90s, yet for v_max > 1 it remains an open question. It is conjectured here that this general solution can be generated from the basic solution (for v_max = 1) by a linear coordinate transformation, the shear mapping, which requires no additional parameters in the deterministic case, and two additional parameters otherwise. The proposed solutions show remarkable agreement with existing numerical solutions, except in the congested regime where the Monte Carlo data shows more concavity than the more linear congested branches predicted by the theory. More research is needed to investigate this bias.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

Abstract: This study reviewed aspects of the biology of two members of the glucosinolate family, namely sinigrin and glucoraphanin and their anti-tumour and anti-microbial properties. Sinigrin and glucoraphanin are converted by the β-sulphoglucosidase myrosinase or the gut microbiota into their bioactive forms, allyl isothiocyanate (AITC) and sulphoraphanin (SFN) which constitute part of a sophisticated defence system plants developed over several hundred million years of evolution to protect them from parasitic attack from aphids, ticks, bacteria or nematodes. Delivery of these components from consumption of cruciferous vegetables rich in the glucosinolates also delivers many other members of the glucosinolate family so the dietary AITCs and SFN do not act in isolation. In-vitro experiments with purified AITC and SFN have demonstrated their therapeutic utility as antimicrobials against a range of clinically important bacteria and fungi. AITC and SFN are as potent as Vancomycin in the treatment of bacteria listed by the World Health Organisation as antibiotic-resistant "priority pathogens" and also act as anti- cancer agents through the induction of phase II antioxidant enzymes which inactivate potential carcinogens. Glucosinolates may be useful in the treatment of biofilms formed on medical implants and catheters by problematic pathogenic bacteria such as Pseudomonas aeruginosa and Staphylococcus aureus and are potent antimicrobials against a range of clinically important bacteria and fungi. The glucosinolates have also been applied in the prevention of bacterial and fungal spoilage of food products in advanced atmospheric packaging technology which improves the shelf-life of these products.

Printed electronic devices are attracting significant interest due to their versatility and low cost; however, quality control during manufacturing is a significant challenge, preventing the widespread adoption of this promising technology. We show that terahertz (THz) radiation can be used for the in situ inspection of printed electronic devices, as confirmed through a comparison with conventional electrical conductivity methods. Our in situ method consists of printing a simple test pattern exhibiting a distinct signature in the THz range that enables the precise characterization of {the static} electrical conductivities of the printed ink. We demonstrate that contactless dual-wavelength THz spectroscopy analysis, which requires only a single THz measurement, is more precise and repeatable than the conventional four-point probe conductivity measurement method. Our results open the door to a simple strategy for performing contactless quality control in real time of printed electronic devices at any stage of its production line.

In this study, the use of recycled diatomaceous earth as the extraction phase in a the solid phase microextraction (SPME) technique for the determination of polycyclic aromatic hydrocarbons (PAHs) in river water samples, with separation/detection performed by gas chromatography-mass spectrometry (GC-MS), is proposed. The optimized extraction conditions are extraction time 70 min at 80 ºC with no addition of salt. The limits of quantification were close to 0.5 μg L-1 with RSD values lower than 25% (n = 3). The linear working range was 0.5 μg L-1 to 25 μg L-1 for all analytes. The method was applied to samples collected from the Itajaí River (Santa Catarina, Brazil) and the RSD values for repeatability and reproducibility were lower than 15% and 17%, respectively. The efficiency of the recycled diatomaceous earth fiber was compared with that of commercial fibers and good results were obtained, confirming that this is a promising option for use as the extraction phase in SPME.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Molecularly imprinted polymers (MIPs) were synthesized and applied for the selective extraction of oblongifolin C (OC) from fruit extracts of Garcinia yunnanensis Hu. A series of experiments and computational approaches were employed to improve the efficiency of screening for optimal MIP systems in the study. The molar ratio (1:4) was chosen at last based on the comparison of the binding energy of the complexes between the template (OC) and functional monomers using density functional theory (DFT) at the RI-PBE-D3-gCP/def2-TZVP level of theory. The binding characterization and the molecular recognition mechanism of MIPs were further explained using the molecular modeling method and NMR and IR spectra data. The reusability of this approach was demonstrated in over 20 batch rebinding experiments. 140.5 mg of OC (>95% purity) was obtained from the 5 g extracts with 2 g of MIPs with the best binding properties through gradient elution program from 35% to 70% methanol-water solution. At the same time, another structural analog, 46.5 mg of guttiferone K (GK) (>88% purity), was also obtained by the gradient elution procedure. Our results showed that the structural analogs could be separated from the crude extracts by the molecularly imprinted solid-phase extraction (MISPE) using a gradient elution procedure for the first time.

Questions：SAP in mountainous cities of China serve as crucial carriers for species and wild food, constituting potential green infrastructure. These patches should be recognized as locally specific resources. This study investigates the transformation characteristics of the landscape patterns of SAP, along with their elements, across urban-rural gradients, providing foundational support for the planning of conservation and utilization strategies. Location: Yongchuan area of Chongqing in southwest China. Methods: The study investigated urban-rural gradient-based transformation of SAP. A four-direction transect space was selected and divided into uniform sample squares. Fragstats 4.3 calculated the landscape index of SAP, and Spearman correlation coefficients in SPSS were used to evaluate the influence of landform and artificial factors on agroforestry patch transformation. Results: 1) Patch area (PA), Plaque density (PD), and CLUMPY of SAP systematically transform, showing increased SAP areas and higher connectivity with greater distance from the city, resulting in reduced patch fragmentation. However, Edge density (ED) and Largest plaque index (LPI) exhibit irregular transformation patterns. 2) With increased distance from the city, woodland patch area and connectivity increase, leading to decreased fragmentation, dispersal, and lower fractal dimensions. Conversely, Cultivated land follows the opposite trend. garden land patch area, fractal dimension, fragmentation, and dispersal all increase, while connectivity decreases. 3) Landscape pattern transformations of SPA are significantly influenced by artificial factors. Woodland patches are influenced similarly by landform and artificial factors. In contrast, cultivated land and garden land patches are more significantly impacted by artificial factors. Conclusions: SAP exhibit differentiated conservation and utilization measures across urban-rural gradients. Small patches located far from urban centers may benefit from systematic conservation measures to prevent further fragmentation and erosion in peri-urban areas.

This article introduces a new way of using a Fibre Bragg Grating (FBG) sensor for detecting the presence and number of occupants in the monitored space in a Smart Home (SH). CO₂ sensors are used to determine the CO₂ concentration of the monitored rooms in an SH. CO₂ sensors can also be used for occupancy recognition of the monitored spaces in SH. To determine the presence of occupants in the monitored rooms of the SH, the newly devised method of CO₂ prediction, by means of an Artificial Neural Network (ANN) with a Scaled Conjugate Gradient (SCG) algorithm using measurements of typical operational technical quantities (indoor temperature, relative humidity indoor and CO₂ concentration in the SH) is used. The goal of the experiments is to verify the possibility of using the FBG sensor in order to unambiguously detect the number of occupants in the selected room (R104) and, at the same time, to harness the newly proposed method of CO₂ prediction with ANN SCG for recognition of the SH occupancy status and the SH spatial location (rooms R104, R203, and R204) of an occupant. The designed experiments will verify the possibility of using a minimum number of sensors for measuring the non-electric quantities of indoor temperature and indoor relative humidity and the possibility of monitoring the presence of occupants in the SH using CO₂ prediction by means of the ANN SCG method with ANN learning for the data obtained from only one room (R203). The prediction accuracy exceeded 90% in certain experiments. The uniqueness and innovativeness of the described solution lie in the integrated multidisciplinary application of technological procedures (the BACnet technology control SH, FBG sensors) and mathematical methods (ANN prediction with SCG algorithm, the Adaptive Filtration with of LMS algorithm) employed for the recognition of number persons and occupancy recognition of selected monitored rooms of SH.

The Double Random Phase Encoding (DRPE) image encryption method has garnered significant attention in color image processing and optical encryption, thanks to its parallel encryption of R, G, B. However, DRPE-based color image encryption faces two challenges. Firstly, it disregards the correlation of R, G, and B, compromising the encrypted image's robustness. Secondly, DRPE schemes relying on Discrete Fourier Transform (DFT) and Discrete Fractional Fourier Transform (DFRFT) are vulnerable to linear attacks, such as Known Plaintext Attack (KPA) and Chosen Plaintext Attack (CPA). Quantum walk stands out as a remarkable tool for designing modern cryptographic mechanisms, offering resistance to potential attacks from both classical and quantum computers.Therefore, this study presents an optical color image encryption algorithm that combines two-dimensional quantum walk with 24-bit plane permutation, dubbed OCT. This approach employs pseudo-random numbers generated by Two-Dimensional Quantum Walking (TDQW) for phase modulation in DRPE and scrambles the encrypted image's real and imaginary parts using the Generalized Arnold Transform. The 24-bit plane permutation helps reduce correlation of the R, G, B, while the Generalized Arnold Transform bolsters DRPE's resistance to linear attacks. By incorporating TDQW, the key space is significantly expanded. Experimental results validate the effectiveness and security of proposed method.

This study aimed to evaluate the safety and tolerability of STP1, a combination of ibudilast and bumetanide, tailored for the treatment of a specific subgroup of patients with Autism Spectrum Disorder (ASD), namely ASD Phenotype 1 (ASD-Phen1). We conducted a randomized, double-blind, placebo-controlled, parallel-group phase 1b study with two 14-day treatment phases (registered at clinicaltrials.gov as NCT04644003). Nine ASD-Phen1 patients were administered STP1, while three received a placebo. We assessed safety and tolerability, along with electrophysiological markers, such as EEG, Auditory Habituation, and Auditory Chirp Synchronization, to better understand STP1's mechanism of action. Additionally, we used several clinical scales to measure treatment outcomes. The results showed that STP1 was safe and well-tolerated, with electrophysiological markers indicating a significant and dose-related reduction of gamma power in the whole brain and in brain areas associated with executive function and memory. Treatment with STP1 also increased alpha 2 power in frontal and occipital regions and improved habituation and neural synchronization to auditory chirps. Although numerical improvements were observed in several clinical scales, they did not reach statistical significance. Overall, this study suggests that STP1 is safe and well-tolerated in ASD-Phen1 patients and shows indirect target engagement in ASD brain regions of interest.

The cucumber mosaic virus (CMV) 2b protein is a suppressor of plant defenses and a pathogenicity determinant. Amongst the 2b protein’s host targets is the RNA silencing factor Argonaute 1 (AGO1), which it binds to and inhibits. In Arabidopsis thaliana, if 2b-induced inhibition of AGO1 is too efficient it induces reinforcement of antiviral silencing by AGO2, and triggers increased resistance against aphids, CMV’s insect vectors. These effects would be deleterious to CMV replication and transmission, respectively, but are moderated by the CMV 1a protein by sequestering sufficient 2b protein molecules into P-bodies to prevent excessive inhibition of AGO1. Mutant 2b protein variants were generated and red and green fluorescent protein fusions used to investigate subcellular colocalization with AGO1 and the 1a protein, and the effects of mutations on complex formation with the 1a protein and AGO1 were investigated using bimolecular fluorescence complementation and co-immunoprecipitation assays. Although we found that residues 56-60 influenced the 2b protein’s interactions with the 1a protein and AGO1, it appears unlikely that any single residue or sequence domain is solely responsible. In silico predictions of intrinsic disorder within the 2b protein secondary structure were supported by circular dichroism (CD) but not by nuclear magnetic resonance (NMR) spectroscopy. Intrinsic disorder provides a plausible model to explain the 2b protein’s ability to interact with AGO1, the 1a protein and other factors. However, the reasons for the conflicting conclusions provided by CD and NMR must first be resolved.

The article is devoted to the research of economic cycles and crises, which are studied within the framework of the theory of long waves by N. D. Kondratiev (K-waves) using the mathematical apparatus of fractional calculus. The object of the study is the mathematical model of S.V. Dubovsky 3 and some of its modifications, which describe the dynamics of the economic system, characterizing the interaction between the efficiency of new technologies and the efficiency of capital productivity. Modifications in the model are determined by the following points: the mathematical model takes into account the dependence of the rate of accumulation on capital productivity, there is an external harmonic influence - the influx of investments and new technological solutions, the economic system has heredity, including time-dependent, which leads to a delayed effect - the system’s response to impact. The property of heredity in the mathematical model is taken into account using fractional derivatives of constant and variable orders. Mathematical model S.V. Dubovsky and its modifications are studied numerically using the Adams-Bashforth-Moulton algorithm. Oscillograms and phase trajectories are constructed, and an interpretation of the simulation results is given.

This study aimed to conduct importance-performance analyses (IPAs) based on the perception of Korean middle-school students toward health management awareness during the post-coronavirus disease 2019 (COVID-19) era. Data were collected from 867 Korean middle-school students via online and offline surveys between May and June 2023. A frequency analysis, a reliability analysis, an IPA based on the entire target students, and an IPA depending on sex were carried out with the collected data, and they revealed the following. First, the IPA results regardless of sex indicated that four factors of the mental health were located in the third quadrant with one factor of the same variable in the fourth quadrant. The three factors of the disease management were located in the third quadrant. As for physical activity, two factors were located in the first quadrant, one in the second quadrant, and one in the third quadrant. As for sleep management, two factors were located in the second quadrant, one in the third quadrant, and one in the first quadrant. As for the eating management, two factors were located in the third quadrant, and one in the fourth quadrant. As for the social distancing variable, all four factors were located in the third quadrant. As for the hygiene management, two factors were located in the first quadrant, one in the third quadrant, and one in the fourth quadrant. Furthermore, the IPA results indicated gender differences in regular sports and vigorous movement activities associated with the physical activity. Additionally, a gender difference was observed in regular diet associated with the eating management. This study proposed possible measures for encouraging adolescents to recognize the importance of health and increase their health-related performance during the COVID-19 endemic phase.

We propose a new hierarchy of the vector derivative nonlinear Schr{\"o}dinger equations and consider the simplest multiphase solutions of this hierarchy. The study of the simplest solutions of these equations led to the following results. First, the three-leaf spectral curves $\Gamma=\{(\mu,\lambda)\}$ of the simplest multiphase solutions have a quite simple symmetry. They are invariant with respect to holomorphic involution $\tau$. The type of this involution depends on the genus of the spectral curve. Or the involution has the form $\tau:(\mu,\lambda)\to(\mu,-\lambda)$, or $\tau:(\mu,\lambda)\to(-\mu,-\lambda)$. The presence of symmetry leads to the fact that the dynamics of the solution is determined not by the entire spectral curve $\Gamma$, but by its factor $\Gamma/\tau$, which has a smaller genus. Secondly, it turned out that the dynamics of the two-component vector $\bp=(p_1,p_2)^t$ is determined, first of all, by the dynamics of its length $\abs{\bp}$. Independent equations determine the dependence of the direction of the vector $\bp$ from its length. In cases where the direction of the vector $\bp$ is fixed, the corresponding spectral curve splits into separate components. In conclusion, we note that, as in the case of the Manakov system, the equation of the spectral curve is invariant with respect to the orthogonal transformation of the vector solutions. I.e., the solution can be found from the spectral curve up to the orthogonal transformation. This fact indicates that the spectral curve does not depend on the individual components of the solution, but on their symmetric functions. Thus, the spectral data of multiphase solutions have two symmetries. These symmetries make it difficult to reconstruct signals from their spectral data. The work contains examples illustrating these statements.

Tight junctions (TJ) are cell-cell adhesive structures that define the permeability of barrier-forming epithelia and endothelia. In contrast to this seemingly static function, TJs display a surprisingly high molecular complexity and an unexpected dynamic regulation, which allows the TJs to maintain a barrier in the presence of physiological forces and in response to perturbations. Cell-cell adhesion receptors play key roles during the dynamic regulation of TJs. They connect individual cells within cellular sheets and link sites of cell-cell contacts to the underlying actin cytoskeleton. Recent findings support roles of adhesion receptors in transmitting mechanical forces and promoting phase separation. In this review, we discuss newly discovered functions of cell adhesion receptors localized at the TJs and their role in the regulation of the barrier function.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Using straightforward and cost-effective methods, persimmon leaves were converted into a high-quality powder. This powder was applied as an adsorbent for the removal of Cu(II) and Cd(II) from aqueous solutions. Scanning electron microscopy (SEM) indicated the presence of particles with non-homogeneous sizes and rough texture. Elemental analysis and the EDX technique confirmed the presence of elements such as sulfur, phosphorus, nitrogen, and oxygen. The results of ¹³C nuclear magnetic resonance (¹³C-NMR), obtained through the cross-polarization technique, suggest the presence of groups containing sulfur and oxygen. Infrared spectroscopy (FTIR) indicated the existence of amine and hydroxyl groups. The material was used in solid-phase extraction of Cu(II) and Cd(II) in batch experiments, and its adsorption capacity was evaluated as a function of time, pH, and analyte concentration. Kinetic equilibrium was reached within 5 minutes, and the experimental data were fitted to the pseudo-second-order kinetic model. The optimum pH for adsorption of both metal species was observed to be around 5.0. The adsorption isotherms were adjusted using the modified Langmuir equation, and the maximum amount of metal species extracted from the solution was determined to be 0.213 mmol g^-1 for Cu(II) and 0.215 mmol g^-1 for Cd(II), with high linear correlation coefficients for both metals. The persimmon leaves are typically abundant during the growing season, and since they are seasonal, the Diospyros kaki L.f. tree undergoes the natural process of leaf abscission, ensuring the availability of leaves for application.

In this paper, we consider the one-dimensional Ising model (shortly, 1D-MSIM) having mixed spin-(s,(2t−1)/2) with nearest neighbors and the external magnetic field. We establish the partition function of the model by means of the transfer matrix. Under a null boundary condition, we compute certain thermodynamic quantities for the 1D-MSIM. We find some precise formulas to determine the model’s free energy, entropy, magnetization, and susceptibility. By examining the model’s associated iterative equations, we use the cavity approach to investigate the phase transition problem. We numerically determine the model’s periodicity.

The work is devoted to the study of a MEMS resonator dynamics under the action of phase-locked and automatic gain control loops. Particular attention is directed to the study of the nonlinearity factor of the resonator elastic restoring force. It was found that the determination of control system parameters based on the stability analysis of the operating resonant mode, in the general case, does not provide the required phase adjustment and stabilization of the oscillation amplitude. Stable multifrequency modes of oscillations are found, an analytical study of the mechanisms of their appearance and evolution is carried out under variation of the key parameters of the system. The real regions of the control system stable operation are determined (which do not coincide, as was found, with the regions of stability of the operating resonant mode, due to the presence of hidden attractors in the phase space of the system). A methodology has been developed for identifying such areas of stable operation. A significant complication of the structure of possible motions in the system with an increase in the Q-factor of the resonator is revealed.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

The out-of-equilibrium dynamics of many body systems has recently received a burst of interest, also due to experimental implementations. The dynamics of both observables, such as magnetization and susceptibilities, and quantum information related quantities, such as concurrence and entanglement entropy, have been investigated under different protocols bringing the system out of equilibrium. In this paper we focus on the entanglement entropy dynamics under a sinusoidal drive of the tranverse magnetic field in the 1D quantum Ising model. We find that the area and the volume law of the entanglement entropy coexist under periodic drive for an initial non-critical ground state. Furthermore, starting from a critical ground state, the entanglement entropy exhibits finite size scaling even under such a periodic drive. This critical-like behaviour of the out-of-equilibrium driven state can persist for arbitrarily long time, provided that the entanglement entropy is evaluated on increasingly subsytem sizes, whereas for smaller sizes a volume law holds. Finally, we give an interpretation of the simultaneous occurrence of critical and non-critical behaviour in terms of the propagation of Floquet quasi-particles.

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

The LiCl and LiNO₃ water solutions in the presence of small amounts of 3-helium have been investigated by means of multinuclear resonance spectroscopy. The resulting concentration dependences of the ³He, ^6,7Li⁺, ¹⁴NO₃^¯ and ³⁵Cl^¯ resonance radiofrequencies are reported in the infinite limit. This data along with new theoretical corrections of shielding lithium ions was analyzed by a known NMR relationship method. Consequently, the nuclear magnetic moments of ⁶Li and ⁷Li were established against that of the helium-3 dipole moment: μ(⁶Li)=+0.822046(5)μ_N and μ(⁷Li)=+3.256418(20)μ_N. The new results were shown to be very close to the previously obtained values of the (ABMR) atomic beam magnetic resonance method. This experiment proves that our helium method is well suited for establishing dipole moments from NMR measurements performed in water solutions. This technique is especially valuable when gaseous substances of the needed element are not available. All shielding constants of species present in water solutions are consistent with new nuclear magnetic moments and these taken as a reference. Both techniques – NMR and ABMR – give practically the same results providing that all shielding corrections are properly made.

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

Synthetic Aperture RADAR (SAR) is a radar imaging technique in which the relative motion of the sensor is used to synthesize a very long antenna and obtain high spatial resolution. Standard SAR raw data processing techniques assume uniform motion of the satellite (or aerial vehicle) and a fixed antenna beam pointing sideway orthogonally to the motion path, assumed rectilinear. Despite SAR data processing is a well established imaging technology that has become fundamental in several fields and applications, in this paper a novel approach has been used to exploit coherent illumination, demonstrating the possibility of extracting a large part of the ancillary data information from the raw data itself, to be used in the focusing procedure. In this work an effort has been carried out to try to focus the raw SAR complex data matrix without the knowledge of anyof the parameters needed in standard focusing procedures as Range Doppler (RD) algorithm, ω - K algorithm and Chirp Scaling (CS) algorithm. All the literature references regarding the algorithms needed to obtain a precise image from raw data use such parameters that refer both to the SAR system acquisition geometry and its radiometric specific parameters. In [12], authors introduced a preliminary work dealing with this problem and able to obtain, in the presence of a strong point scatterer in the observed scene, good quality images, if compared to the standard processing techniques. In this work the proposed technique is described and performances parameters are extracted to compare the proposed approach to RD.

This year marks the 20th anniversary of the discovery that proteins with various cellular functions can be temporarily immobilized in the nucleolus, a process known as nucleolar sequestration. This review reflects on the progress made to understand the physiological roles of nucleolar sequestration and the mechanisms involved in protein immobilization. We discuss how nucleolar sequestration consists of a highly choreographed amyloidogenic liquid-to-solid phase transition that converts the nucleolus into Amyloid bodies (A-bodies). The study of solid condensates A-bodies will offer unique perspectives on cellular assembly of membrane-less compartments and provide alternative insights on pathological amyloidogenesis involved in neurological disorders.

Human Face and facial parts are the most significant parts as it reveals a person’s true identity. It plays an important role in various biometric applications like crowd analysis, human tracking, photography, cosmetic surgery, etc. There are many techniques are available to detect a facial image. Among them, skin detection is the most popular one. The aim of this paper is to detect first the person's identity from facial image and finally check any spot present the the detected person. The first step is to detect the maximum skin region based on a combination method of RGB and HSV color space model. Next it is to verify the skin areas of human through machine learning approach. The Aggregated Channel Features (ACF) detector is used to identify the different facial parts like eye pairs, nose, and mouth. Bootstrap aggregation decision tree classifier is applied to classify the person’s identity based on Histogram Oriented Gradient (HOG) features value. The experimental results show that the proposed method gives the average 97% accuracy.

Breast cancer is the most common cause of death for women worldwide. Thus, the ability of artificial intelligence systems to predict and classify breast cancer is very important. In this paper, a hybrid ensemble method classification mechanism is proposed based on a majority voting mechanism. First, the performance of different state-of-the-art machine learning classification algorithms for the Wisconsin Breast Cancer Dataset (WBCD) were evaluated. The three best classifiers were then selected based on their F3 score. F3 score is used to emphasize the importance of false negatives (recall) in breast cancer classification. Then, these three classifiers, simple logistic Regression learning, stochastic gradient descent learning and multilayer perceptron network, are used for ensemble classification using a voting mechanism. We also evaluated the performance of hard and soft voting mechanism. For hard voting, majority-based voting mechanism was used and for soft voting we used average of probabilities, product of probabilities, maximum of probabilities and minimum of probabilities-based voting methods. The hard voting (majority-based voting) mechanism shows better performance with 99.42% as compared to the state-of-the-art algorithm for WBCD.

The draconian regulation required by the inherent instability of cognitive phenomena -- gene expression, immune function, cancer suppression, wound healing, animal consciousness, machine intelligence, network stabilization, institutional cognition, and their many and varied composites -- can be viewed through the lens of the asymptotic limit theorems of both information and control theories. Here, we explore the dynamics and sometimes highly punctuated failures of the regulation of cognition under increasing `noise'. The approach parallels, and indeed generalizes, the Data Rate Theorem of control theory, extending the theorem's requirement of a minimum channel capacity necessary for stabilization of an inherently unstable system. Various models are explored across different basic underlying probability distributions characteristic of the system under study, and across different hierarchical scales, finding the addition of adaptive -- learned -- regulation greatly extends the reach of innate -- e.g., AI-driven or otherwise pre-programmed -- regulation. This work points toward the construction of new statistical tools for the analysis of observational and empirical data across a wide spectrum of inherent pathologies and adversarial challenges afflicting a wide variety of cognitive processes.

Weak interaction processes continue to be hot topics in fundamental physics research. In this paper, we briefly review some recent advances in the theoretical study of beta and double-beta decays that include both the nuclear and atomic part of these processes. On the nuclear side, we present a statistical approach for the computation of the nuclear matrix elements (NME) for neutrinoless double-beta (0νββ). A range of NME values, the most probable value for NME, and the associated theoretical uncertainty are given. Correlations with other related observables are shown as well. On the atomic side, we first briefly review the methods used to get the electrons’ wave functions. Further, we use them for the computation of some relevant kinematic quantities such as Fermi functions, electron spectra and angular correlation between the emitted electrons. Then, we present applications of these calculations to the experimental data analysis related to the search of the Lorentz invariance violation in two-neutrino double-beta (2νββ) decay and description of the decay rates and decay rate ratios for allowed and unique forbidden electron capture (EC) processes.

Background: Malnutrition was associated with worse survival outcomes, impaired quality of life, and deteriorated performance status across various cancer types. We aimed to identify risk factors for malnutrition in patients with epithelial ovarian(EOC) and impact on survival. Methods: In our prospective study, we included the patients with primary and recurrent EOC, tubal or peritoneal cancer conducted. We assessed serum laboratory parameters, body mass index, nutritional risk index, nutritional risk screening score(NRS-2002), and bio-electrical impedance analysis. Results: We recruited a total of 152. Patients >65 years-old, with ascites of >500 ml, or with platinum-resistant EOC showed statistically significant increased risk of malnutrition when evaluated by NRS-2002(p-values = 0.014, 0.001, and 0.007, respectively). An NRS-2002<3 was an independent predictive factor for complete tumor resectability (p=0.009). The patients with NRS-2002≥3 had a median overall survival(OS) of seven months (95% CI=0-24 months), as compared to the patients with NRS-2002<3 where median OS was 46 months(p=0,001). Phase angle(PhAα)≤ 4.5 was the strongest predictor of OS. Conclusion: Malnutrition is an independent predictor of incomplete cytoreduction in study population. It is an independent prognostic factor for poor OS. Preoperative nutritional assessment is an effective tool in identification of high-risk groups within EOC characterized by poor clinical outcome.

The majority of current methods for measuring the angular deflection of a laser beam enable measurement only in one selected plane. However, there are tasks in which measurements of laser beam deflections in 3D are required. In this paper, we present a way of enabling two-axial measurements of the deflection of a beam based on a single-axis sensor. The key idea is to direct a laser beam alternately into one of two arms of a measurement system. In the first arm, the beam is transmitted directly to the angular sensor, while in the second, the beam is directed to the sensor via a special optical element that rotates the plane of the beam deflection; in other words, this element changes the deflection in the horizontal plane into a deflection in the vertical plane, and vice versa. To alternate the path of the beam, a variable phase retarder and a polarising beamsplitter are used. The proposed technique is experimentally verified, and the results confirm its effectiveness.

An overview of the link between nonequilibrium thermodynamics and complexity theory is offered. It is shown how the rate of entropy production can be quantified through the spectrum of the Lyapunov exponents. It was shown how the entropy production per unit of time meets the necessary and sufficient conditions to be a Lyapunov function and constitutes per se an extremal principle. The entropy production fractal dimension conjecture was established. It is shown how the rate of entropy production as a non-extremal criterion represents an alternative way of sensitivity analysis of differential equations. Finally, an extension to biophysical-chemical systems, on the one hand, the use of the dissipation function is shown, as a thermodynamic potential out of equilibrium, in the characterization of biological phase transitions. On the other hand, it was evidenced how the rate of entropy production represents a physical quantity to evaluate the complexity and robustness of cancer.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

in order to enhance the separation performance and to reduce the heat loss of the transmembrane for membrane distillation, the thermal efficiency and hydrophobicity of the membrane distillation should be simultaneously enhanced. In this work, a PVDF/PET hydrophobic/hydrophilic membrane is prepared by non-solvent phase inducing method. Nanosized silica aerogel (SiAG) with high porosity is added to the composite membranes. The modifying effects and operating conditions on permeate flux and thermal efficiency in direct contact membrane distillation (DCMD) are investigated. Furthermore, the latent heat of vaporization and the heat transfer across the membranes are compared for SiAG addition, which indicates that the composite PVDF@SiAG/PET membranes display a great potential for distillation-separation application with high heat efficiency.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

Aim: The main purpose of this feasibility study was to estimate compliance and acceptability rate of a 9-Steps mobile app preparation program. Subsequently, to assess its impact regarding attitudes towards smoking cessation. Methods: The program was only available on versions above iOS 13.3. The ecological study collected user’s data via the app from 04/07/2021 to 28/07/2021. Results: A total of 2331 ecological users completed onboarding; 1926 users (73.9%) completed the step 0 and only 265 users continued in step 1. On average, participants actively engaged with intra-steps activities (85,1%). Most users were highly satisfied at the end of each step. On average 86% found the content of each step comprehensive and relevant. Mann-Whitney tests demonstrated positive changes in attitudes toward smoking cessation on the less confident users: willing (3 to 5, p <.05); confidence (3 to 5, p <.001) and readiness to quit (3 to 5, p <.001). Conclusions: This ecological study corroborates the expected dropout between first use and regular use of health mobile apps. However, engagement and satisfaction rates support the feasibility and acceptability of a 9-step preparation program. Additional research is needed to better understand determinants of regular use of mobile apps and its impact on the target behavior.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

Short chain quinones (SCQs) have been identified as potential drug candidates against mitochondrial dysfunction, which is largely dependent on their reversible redox characteristics of the active quinone core. We recently synthesized a SCQ library of > 148 naphthoquinone derivatives and identified 16 compounds with enhanced cytoprotection compared to the clinically used benzoquinone idebenone. One of the major drawbacks of idebenone is its high metabolic conversion in the liver, which significantly restricts is therapeutic activity. Therefore, this study assessed the metabolic stability of the 16 identified naphthoquinone derivatives 1-16 using hepatocarcinoma cells in combination with an optimized reverse-phase liquid chromatography (RP-LC) method. Most of the derivatives showed significantly better stability than idebenone over 6 hours (p < 0.001). By extending the side-chain of SCQs, increased stability for some compounds was observed. Metabolic conversion from the derivative 3 to 5 and reduced idebenone metabolism in the presence of 5 were also observed. These results highlight the therapeutic potential of naphthoquinone-based SCQs and provide essential insights for future drug design, prodrug therapy and polytherapy, respectively.

The early diagnosis of mastitis represents an essential factor for a prompt detection of the animal for further actions. In fact, if not culled, infected cows must be segregated from the milking herd and milked last, or milked with separate milking units. Besides microbiological analysis, the somatic cell count (SCC) commonly used as predictor of intramammary infection, frequently lead to a misclassification of milk samples. To overcome these limitations, more specific biomarkers are continuously evaluated. Total amino acid content increases significantly in mastitic milk compared to normal one. Bovine mastitis can arise as a result of infection of the mammary gland by Staphylococcus aureus. Multiplication of this bacterium within the mammary gland is required for infection to persist. S. aureus requires branched-chain amino acids (BCAAs: isoleucine, leucine, valine) for protein synthesis, branched-chain fatty acids synthesis and environmental adaptation by responding to their availability via transcriptional regulators. The importance of BCAAs for S. aureus physiology necessitates that it either synthesize them or scavenge them from the environment. Increase of BCAAs in composite milk has been postulated to be linked to mammary infection by S. aureus. In the present work, we demonstrated, by a direct ion-pairing reversed-phase method based on the use of the evaporative light-scattering detector (IP-RP-HPLC-ELSD), applied to 65 composite cow milk samples, a correlation between the concentration of isoleucine and leucine and S. aureus load.

Luminescence-based sensors for measuring oxygen concentration are widely used both in industry and research due to the practical advantages and sensitivity of this type of sensing. The measuring principle is the luminescence quenching by oxygen molecules, which results in a change of the luminescence decay time and intensity. In the standard approach, this change is related to an oxygen concentration using the Stern–Volmer equation. This equation, which in most of the cases is non-linear, is parametrized through device-specific constants. Therefore, to determine these parameters every sensor needs to be precisely calibrated at one or more known concentrations. This work explores an entirely new artificial intelligence approach and demonstrates the feasibility of oxygen sensing through machine learning. The specifically developed neural network learns very efficiently to relate the input quantities to the oxygen concentration. The results show a mean deviation of the predicted from the measured concentration of 0.5 % air, comparable to many commercial and low-cost sensors. Since the network was trained using synthetically generated data, the accuracy of the model predictions is limited by the ability of the generated data to describe the measured data, opening up future possibilities for significant improvement by using a large number of experimental measurements for training. The approach described in this work demonstrates the applicability of artificial intelligence to sensing technology and paves the road for the next generation of sensors.