Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

The divination function of China's Yijing has led to its circulation for thousands of years. In our exploration of Yijing's characteristics using big data, we have discovered variations in results between the coin toss method and the ancient yarrow-stalk method of divination, known as "the number for the great expansion method of divination(大衍之数)". The yarrow-stalk method serves as the fundamental method of divination in Yijing and continues to hold significance in studying the essential characteristics of Yijing. Despite the complexity of yarrow calculations, advancements in computer technology and big data have simplified its application. By employing the yarrow-stalk method, we simulated changes in the 64 hexagrams, calculated probabilities and proportions of hexagram alterations, and derived fundamental characteristics and patterns of hexagrams. Additionally, we constructed the spatial representation of lines and hexagrams. Through a binary system rearrangement, we created a 64x64 matrix illustrating hexagram transformations. Subsequently, we generated 100 million random hexagrams and analyzed line and hexagram changes accordingly. Our findings indicate the following:(1) Big data analysis reveals evident asymmetry in the hexagrams obtained through the yarrow-stalk method, with a triangular fractal characteristic forming the background.(2) Each of the 64 hexagrams exhibits a distinct probability distribution when transforming into other hexagrams, which can be categorized into five types.(3)The occurrence probabilities of Laoyang, Laoyin, Shaoyang, and Shaoyin are 18.61%, 6.387%, 31.38%, and 43.62% respectively. The probabilities of Yin and Yang occurrences are nearly equal, each close to 50%. However, the probability of Laoyang is approximately three times higher than that of Laoyin.(4) Visualized and analyzed the characteristics of hexagram changes greater than 100000 times using 3D statistical maps and Sankey diagram.These results demonstrate that the yarrow-stalk method effectively unveils the characteristics and underlying patterns of the 64 hexagrams. This study provides a novel approach for scientifically exploring the internal laws governing the 64 hexagrams in Yijing.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

Scope, time, and cost permanently effects each other and most of Information Technology projects fails due to these three factors. Scope shifting mostly occur due to time and cost. At project start, lack of understanding of project and product scope is focal involvement that leads to unsuccessful projects. Complete software scope definition determines quality of project. Defining the customer requirement and the definite scope of project has key role for implementation of project management. The complications originates when systems are developed from impractical expectations and misunderstanding requirements. These problems are cause of many changes, occurs in system development and leads to poor scope management. Scope creep is one of the momentous prompting parameter on the success of project. The failure in manage scope creep leads for 80 percent of software projects failure. However, using agile approach the impact of scope creep on projects become insignificant. A correctly distinct scope tends us to develop a quality product, within identified plans and decided cost to the stake-holders.

The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete break-down of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit (Q²) and the standard deviation (σ) of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol (N=3386 test molecules) for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol (N=1791) for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol (N=373) for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K (N=2637) for the entropy of fusion and 0.5804 and 32.79 J/mol/K (N=2643) for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules, for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation coefficient R² of 0.6066.

We examine how observations can be used to evaluate an air quality analysis by verifying against passive observations (i.e. cross-validation) that are not used to create the analysis and we compare these verifications to those made against the same set of (active) observations that were used to generate the analysis. The results show that both active and passive observations can be used to evaluate of first moment metrics (e.g. bias) but only passive observations are useful to evaluate second moment metrics such as variance of observed-minus-analysis and correlation between observations and analysis. We derive a set of diagnostics based on passive observation–minus-analysis residuals and we show that the true analysis error variance can be estimated, without relying on any statistical optimality assumption. This diagnostic is used to obtain near optimal analyses that are then used to evaluate the analysis error using several different methods. We compare the estimates according to the method of Hollingsworth Lonnberg, Desroziers, a diagnostic we introduce, and the perceived analysis error computed from the analysis scheme, to conclude that as long as the analysis is optimal, all estimates agrees within a certain error margin. The analysis error variance at passive observation sites is also obtained.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

The introduction of electrical vehicle charging infrastructure including EV charger, renewable energy resource at secondary feeder in distribution system has been increased as one of countermeasure for global environmental issues. However, the Electric Vehicle Charging (EVC) infrastructure may act as the peak load in distribution system, which can adversely impact on the voltage stability when the electric vehicle is quickly charged. Therefore, to keep within the limit capacity of secondary feeder and allowable limit for feeder voltage, this paper proposes a stabilization method by the Energy Storage System (ESS) control strategy at secondary feeder in order to be not violated over than lower and upper limit. Also, this paper presents the estimation method to keep the proper standard value of State of Charge (SOC). From the simulation results, the voltage stabilization operation by ESS should make the feeder voltages of the distribution system(secondary feeder) introduced EVC Infra keep better voltage conditions, also estimation method to keep the proper standard value is confirmed that the SOC of ESS when is the standby condition could be exactly kept within the proper reference range.

The stability properties of the Hill equation are discussed, and especially those of the Mathieu equation that characterize ion motion in electrodynamic traps. The solutions of the Mathieu equation for a trapped ion are characterized by using the Floquet theory and Hill's Method solution, which yields an infinite system of linear and homogeneous equations whose coefficients are recursively determined. Stability is discussed for parameters $a$ and $q$ that are real. Characteristic curves are introduced naturally by the Sturm-Liouville problem for the well known even and odd Mathieu equations $ce_m(z,q)$ and $se_m(z,q)$. We illustrate the stability diagram for a combined (Paul and Penning) trap and represent the frontiers of the stability domains for axial and radial motion. In case of a Paul trap the stable solution corresponds to a superposition of harmonic motions. The problem of evaluating the maximum amplitudes of stable oscillations for the ideal conditions (taken into consideration) is also approached. Anharmonic corrections are discussed within the frame of the perturbation theory, while the frontiers of the modified stability domains are determined as a function of the chosen perturbation parameter. The results apply to 2D and 3D ion traps used for different applications in quantum engineering, among which optical clocks, quantum logic and quantum metrology, but not restricted only to these.

In this paper, we propose an efficient numerical method to solve the diffusive logistic model with a free boundary which is often used to simulate the spreading of the new or invasive species. The boundary movement is tracked by the level-set method, where the Hamilton-Jacobi weighted essentially nonoscillatory (HJ-WENO) scheme is utilized to capture the boundary curve embedded by the Cartesian grids via the embedded boundary method. Then the radial basis function-finite difference (RBF-FD) method is adopted to the spatial discretization and the IMEX scheme is considered for time integration. A variety of numerical examples are carried out to demonstrate the evolution of diffusive logistic model in different initial boundaries.

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

The aim of this paper is to study a semi-functional partial linear regression model (SFPLR) for spatial data with responses missing at random. The estimators are constructed by the kernel method, and some asymptotic properties such as probability convergence rates of the nonparametric component and asymptotic distribution of the parametric and nonparametric components are established under certain conditions. Next, the performances and the superiority of these estimators are presented and examined using a study on simulated data and on real data by carrying out a comparison between our semi-functional partially linear model with MAR estimator (SFPLRM), the semi-functional partially linear model with the full-case estimator (SFPLRC) and the nonparametric functional model estimator with MAR (FNPM). The results show that the proposed estimators outperform existing estimators as the number of random missing data increases.

A formulation of the Density Functional Theory (DFT) is constructed as an application of the method of maximum entropy for an inhomogeneous fluid in thermal equilibrium. The use of entropy as a systematic method to generate optimal approximations is extended from the classical to the quantum domain. This process introduces a family of trial density operators that are parametrized by the particle density. The optimal density operator is that which maximizes the quantum entropy relative to the exact canonical density operator. This approach reproduces the variational principle of DFT and allows a simple proof of the Hohenberg-Kohn theorem at finite temperature. Finally, as an illustration, we discuss the Kohn-Sham approximation scheme at finite temperature

This article presents a novel sustainable business management technique, emphasizing description and estimation over the outdated profit metric. Due to the intricacies and challenges of implementing the 2019 capital management method based on capital valuation (implemented in 2020–2022), a simpler approach became essential. While it is plausible for organizations to implement capital management based on their valuation, undertaking it with no outside help presents a challenge. The new descriptive method is fundamentally distinct in that detailed monetary valuations of capitals are omitted in favor of description and estimation. This paper establishes the groundwork for applying the new approach in several stages and introduces three new management indicators—the overall accomplishment of management goals index (evaluating management efficacy), the capital level index, and the adjustment (compliance) index—replacing the profit metric. Noteworthy advantages include separating the assessment of management outcomes from the organization's condition, including human and social capital into efficiency evaluations, and removing the profit indicator for management purposes, which prevents resource waste and enhances company efficiency and effectiveness.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

Land-use planning review seems relatively lower in publication rate and in coverage of content. This review contributes its part in two dimensions. First, it assesses ability of the popularly growing bibliometric method in tracking the real contribution of publications. Then it summarizes developments in the land use planning literature in three themes - general literature path building, land use planning context, and development of methods. It is observed that bibliometric method rewards information carriage paper more than the original contributors. Key planning context gaps include detachment of the general goal-oriented objective formulations from the basic land use allocation theories and models and certain urban land use optimization objectives even contradict the original though of sustainable city. Key research frontiers include: linking basic land use allocation and utility theories in urban land use planning; shifting the current urban land use planning from spatial optimization to activities into optimizing flow resources to available spatial configurations; evaluating existing built environment for optimality; transferring knowledge from rural land-use planning to urban land use planning. In method development, the key frontier would be advancing the current loosely coupled methods into more integrated systems.

Due to the intermittency and fluctuation of photovoltaic (PV) output power, a high proportion of grid-connected PV power generation systems has a significant impact on power systems. Accurate PV power forecasting can alleviate the uncertainty of the PV power and is of great significance for the stable operation and scheduling of the power systems. Therefore, in this study, a feature rise-dimensional (FRD) two-layer ensemble learning (TLEL) model for short-term PV power deterministic forecasting and probability forecasting is proposed. First， based on the eXtreme Gradient Boosting (XGBoost), Random Forest (RF), CatBoost, and Long-short-term memory (LSTM) models, a TLEL model is constructed utilizing the ensemble learning algorithm. Meanwhile, the FRD method is introduced to construct the FRD-XGBoost-LSTM (R-XGBL), FRD-RF-LSTM(R-RFL), and FRD- CatBoost - LSTM (R-CatBL) models. Subsequently, the above models are combined to construct the FRD-TLEL model for deterministic forecasting, and perform probability interval forecasting based on quantile regression(QR). Finally, the performance of the proposed model is demonstrated with a real-world dataset. By comparing with other models, the proposed model displays better forecasting accuracy for deterministic forecasting and reliable forecasting intervals for probability forecasting, and good generalization ability in the datasets of different seasons and weather types.

Polo-like kinase 1 (PLK1) plays a pivotal role in cell division regulation and emerges as a promising therapeutic target for cancer treatment. Consequently, the development of small-molecule inhibitors targeting PLK1 has become a focal point in contemporary research. The adenosine triphosphate (ATP)-binding site and the polo-box domain in PLK1 present crucial interaction sites for these inhibitors, aiming to disrupt the protein's function. However, designing potent and selective small-molecule inhibitors can be challenging, requiring a deep understanding of protein-ligand interaction mechanisms at these binding sites. In this context, our study leverages the fragment molecular orbital (FMO) method to explore these site-specific interactions in-depth. Through the FMO approach, we used the FMO method to elucidate the molecular mechanisms of small-molecule drug binding to these sites to design PLK1 inhibitors that are both potent and selective. Our investigation further entailed a comparative analysis of various PLK1 inhibitors, each characterized by distinct structural attributes. This comparison enhanced our understanding of the structure-activity relationships of these inhibitors, underscoring the efficacy of the FMO method in identifying critical binding features and predicting binding modes for small-molecule ligands. Furthermore, Our research spotlighted "hot spot" residues instrumental for selective and robust PLK1 binding. Our findings offer profound insights, priming the rational design of innovative potential PLK1 inhibitors with significant implications for developing anticancer therapeutics.

This article focuses on methods for designing heuristic models within the paradigm of systems theory and in the disciplinary context of intercultural communication. The main question arises from the striking observation that the common language is insufficient to develop knowledge about human communication, especially when many factors of complexity (such as ambiguity, paradoxes, or uncertainty) are involved in the composition of an abstract research object. This epistemological, theoretical, and methodological problematic is one of the main challenges to the scientificity of anthropological theories and concepts on culture. Moreover, these questions lie at the heart of research in intercultural communication. Authors and theorists in the complexity sciences have already stressed the need, in such case, to think in terms of models or semiotic representations, since these tools of thought can mediate much more effectively than unformalized language between the heterogeneous set of perceptions arising from the field of experience, on the one hand, and the philosophical principles that organize speculative thought, on the other. This sets the scene for a reflection on the need to master the theory of heuristic models when it comes to developing scientific knowledge in the field of intercultural communication. In this essay, my first aim is to make explicit the conditions likely to ensure the heuristic value of a model, while my second aim is to clarify the operational function and required level of abstraction of certain terms such as concepts, categories, headings, models, systems, or theories that are among the most commonly used by academics in their descriptive accounts or explanatory hypotheses. To achieve this second objective, I propose to create cognitive meta-categories to identify the three (nominal, cardinal or ordinal) roles of words in the reference grids we use to classify our ideas, and to specify how to use these meta-categories in the construction of our heuristic models. Alongside the theoretical presentation, examples of application are provided, almost all of which are drawn from my own research into the increased cultural vigilance of the majority population in Quebec since the reasonable accommodation crisis in this French-speaking province of Canada. The typology I propose will perhaps help to avoid the confusions regularly committed by authors who attribute only cosmetic functions to words that nevertheless have a highly heuristic value, and who forget to consider the logical leaps of their theoretical thinking in the construction of heuristic models.

The influence of neutrosophy in the previous period is constantly growing in many areas of science and technology. Moreover, various applications of the neutrosophic approach have become more common in recent years. Our goal in this research is to utilize the neutrosophy to improve the performance of the Dai-Liao conjugate gradient (CG) method. Specifically, in this research, we propose and investigate a new neutrosophic logic system to calculate the key parameter t involved in the Dai–Liao CG iterations. Theoretical analysis and numerical experience indicate that the efficiency and robustness of the new rule for determining t. Combining the neutrosophy and the Dai-Liao conjugate gradient method, we propose and explore a new Dai-Liao CG iterations for solving large-scale unconstrained optimization models. The global convergence is established under common assumptions and the backtracking line search. Finally, by conducting numerical experiments, computational evidence demonstrates that the new fuzzy neutrosophic Dai-Liao conjugate gradient method is computationally effective and robust.

The inverse Finite Element Method (iFEM) is a model-based technique to compute the displacement (and then the strain) field of a structure from strain measurements and a geometrical discretization of the same. Different literature works exploit the error between the numerically reconstructed strains and the experimental measurements to perform damage identification in a Structural Health Monitoring framework. However, only damage detection and localization are performed, without attempting a proper damage size estimation. The latter could be based on machine learning techniques, however, an a priori definition of the damage conditions would be required. To overcome these limitations, the present work proposes a new approach in which the damage is systematically introduced in the iFEM model to minimize its discrepancy with respect to the physical structure. This is performed with a maximum likelihood estimation framework, where the most accurate damage scenario is selected among a series of different models. The proposed approach is experimentally verified on an aluminum plate subjected to fatigue crack propagation, which enables the creation of a Digital-Twin of the structure itself. The strain field fed to the iFEM routine is experimentally measured with an Optical Backscatter Reflectometry fiber and the methodology is validated with independent observations of lasers and the Digital Image Correlation.

Detailed flow distributions in vascular systems are the key to identifying hemodynamic risk factors for the development and progression of vascular diseases. Although computational fluid dynamics (CFD) has been widely used in bioengineering research on hemodynamics predictions, not only are high-fidelity CFD simulations time-consuming and computing-expensive, but also not friendly to clinical applications due to the difficulty of comprehensive numerical calculations. Machine learning (ML) algorithums to estimate the flow field in vascular systems based on the angiographic images of the blood flow using existed diagnostic tools are emerging as a new pathway to facilitate the mapping of hemodynamics. In present work, the dye injection in a water flow was simulated as an analogy of the contrast perfusion in blood flow using CFD. In the simulation, the light passes through the flow field and generates projective images, as an analogy of X-ray imaging. The simulations provide both the ground truth velocity field and the projective images of the flow with dye patterns. A rough velocity field was estimated using the optical flow method (OFM) based on projective images. ML algorithums are then trained using the ground truth CFD data and the OFM velocity estimation as the input. Finally, the interpretable (logistic regression) and deep (neural networks, convolutional neural networks, long short term memory) machine learning models are validated by using parallel in vitro experiments on the same flow setup. The validation results showed that the employed ML model significantly reduced the error rate from 53.5% to 2.5% in average for the v-velocity estimation.

This paper focuses on the combination of the method of moments and the wire-grid approximation as an effective computational technique for modeling symmetrical antennas with low computational cost and quite accurate results. The criteria and conditions for the use of wire-grid surface approximation from various sources are presented together with new recommendations for modeling symmetrical antenna structures using the wire-grid approximation. These recommendations are used to calculate the characteristics of biconical and horn antennas at different frequencies. The results obtained using different grid and mesh settings are compared to those obtained analytically. Moreover, the results are compared to those obtained using the finite difference time domain numerical method, as well as the measured ones. All results are shown to be in a good agreement. The used recommendations for building a symmetrical wire-grid of those symmetrical antenna elements provided the most advantageous parameters of the grid and mesh settings and the wire radius, which are able to give a quite accurate results with low computational cost. Additionally, the known equal area rule was modified for a rectangular grid form. The obtained radiation patterns of a conductive plate using both the original rule and the modified one are compared with the electrodynamic analysis results. It is shown that the use of the modified rule is more accurate when using a rectangle grid form.

A data-driven analysis method known as dynamic mode decomposition (DMD) approximates the linear Koopman operator on projected space. In the spirit of Johnson-Lindenstrauss Lemma, we will use random projection to estimate the DMD modes in reduced dimensional space. In practical applications, snapshots are in high dimensional observable space and the DMD operator matrix is massive. Hence, computing DMD with the full spectrum is infeasible, so our main computational goal is estimating the eigenvalue and eigenvectors of the DMD operator in a projected domain. We will generalize the current algorithm to estimate a projected DMD operator. We focus on a powerful and simple random projection algorithm that will reduce the computational and storage cost. While clearly, a random projection simplifies the algorithmic complexity of a detailed optimal projection, as we will show, generally the results can be excellent nonetheless, and quality understood through a well-developed theory of random projections. We will demonstrate that modes can be calculated for a low cost by the projected data with sufficient dimension.

The paper describes the Field Boundary Element Method applied to the fracture analysis of a 2D rectangular plate made of Functionally Graded Material to calculate Mode I Stress Intensity Factor. The object of the Field Boundary Element Method is the transversely isotropic plane plate. Its material presents an exponential variation of the elasticity tensor depending on a scalar function of position, i.e., the elastic tensor results from multiplying a scalar function by a constant taken as a reference. Several examples using a parametric representation of the structural response show the suitability of the method that constitutes a sight of Stress Intensity Factor evaluation of Functionally Graded Materials plane plates even in the case of more complex geometries.

In this paper we perform numerous numerical studies for the problem of low-rank matrix completion. We compare the Bayesian approaches and a recently introduced de-biased estimator which provides a useful way to build confidence intervals of interest. From a theoretical viewpoint, the de-biased estimator comes with a sharp minimax-optimal rate of estimation error whereas the Bayesian approach reaches this rate with an additional logarithmic factor. Our simulation studies show originally interesting results that the de-biased estimator is just as good as the Bayesian estimators. Moreover, Bayesian approaches are much more stable and can outperform the de-biased estimator in the case of small samples. However, we also find that the length of the confidence intervals revealed by the de-biased estimator for an entry is absolutely shorter than the length of the considered credible interval. These suggest further theoretical studies on the estimation error and the concentration for Bayesian methods as they are being quite limited up to present.

Abstract: Polylactic acid (PLA) is brittle in nature with extensive deformation property. For improvement of the end-use quality, it is of significant importance to enhance the producibility of fused deposition modeling (FDM)-printed objects in PLA. The purpose of this investigation is to boost toughness and to reduce the production cost of the FDM-printed tensile test samples with the desired part thickness. To attain the research purpose number of experiments are designed and analyzed by the Response Surface Method (RSM). The statistical analysis is performed to deal with this concern considering layer thickness, infill percentage, and extruder temperature as controlled factors. The tensile test specimens are printed based on the designed experiments, and the tensile strength tests are conducted by SANTAM 150 universal testing machine based on ASTM D638. The honeycomb internal fill pattern is applied for the production of light-weight and high-strength specimens. The area under Force- Extension curve up to fracture is acquired as the toughness of the printed specimens. This study also developed a modeling process using ANN and ANN-GA techniques for developing an accurate estimation for toughness, part thickness, and production cost as dependant variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid ML technique could successfully improve the accuracy of modeling about 7.5, 11.5 and 4.5 % for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. In the other side, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which develops the usability of printed PLA objects. The research is accomplished under the constraints of PLA compatibility with existing fused deposition modeling setup without changing the functional hardware/software of the machine. Although the mechanical properties and dimensional accuracy of PLA have already been studied, there is little literature on the toughness of the printed PLA with honeycomb internal fill pattern.

In recent years, the management of health systems is a main concern of governments and decision makers. Home health care is one of the newest methods of providing services to patients in developed societies that can respond to the individual lifestyle of modern age and the increase of life expectancy. The home health care routing and scheduling problem is a generalized version of the vehicle routing problem, which is extended to a complex problem by adding special features and constraints of health care problems. In this problem, there are multiple stakeholders such as nurses for which an increase of their satisfaction level is very important. In this study, a mathematical model is developed to expand traditional home health care routing and scheduling models to downgrading cost aspects by adding the objective of minimizing the difference between the actual and potential skills of the nurses. Downgrading can lead to a dissatisfaction of the nurses. In addition, skillful nurses have higher salaries and high-level services increase equipment costs and need more expensive trainings and nursing certificates. Therefore, downgrading can enforce hidden huge costs to the managers of a company. To solve the bi-objective model, an -constraint based approach is suggested and the model applicability and its ability to solve the problem in various sizes are discussed. A sensitivity analysis on the Epsilon parameter is conducted to analyze the effect of this parameter on the problem. Finally, some managerial insights are presented to help the managers in this field, and some directions for future studies are mentioned as well.

In this article, the Legendre-Gould Hopper polynomials are combined with Sheffer sequences to introduce certain mixed type special polynomials. Generating functions, differential equations and certain other properties of Legendre-Gould Hopper based Sheffer polynomials are derived. Further, operational and integral representations providing connections between these polynomials and known special polynomials are established. Certain identities and results for some members of these new mixed polynomials are also obtained. Finally, the determinantal definitions of Legendre-Gould Hopper based Sheffer polynomials are also given.

Methods for high-quality DNA extraction and knowledge of sex expression and flowering time are essential for applying genomic-assisted breeding and improve the success with hybridization in Guinea yam. A dioecious or monoecious pattern of flowering and sometimes non-flowering is a common phenomenon within and between the Dioscorea species. The flowering in yam plants raised from botanical seeds often takes an extended period, mostly till the first clonal generation after propagation from the tubers. The prolonged process of testing required to identify plant sex and flowering intensity in yam breeding often poses a challenge to realize reduced breeding cycle and apply genomic selection. This study assessed sample preservation methods for DNA quality during extraction and potential of DNA marker to diagnose plant sex at the early seedling stage in white Guinea yam. The predicted sex at the seedling stage was further validated with the visual score for the sex phenotype at the flowering stage. DNA extracted from leaf samples preserved in liquid nitrogen, silica gel, dry ice, and oven drying methods was similar in quality with a high molecular weight than samples stored in ethanol solution. Yam plant sex diagnosis with the DNA marker (sp16) identified a higher proportion of ZW genotypes (female or monoecious phenotypes) than the ZZ genotypes (male phenotype) in the studied materials with 74% prediction accuracy. The results from this study provided valuable insights on suitable sample preservation methods for quality DNA extraction and the potential of DNA marker sp16 to predict sex in white Guinea yam.

Original and improved version of the Hardy Cross iterative method with related modifications are today widely used for calculation of fluid flow through conduits in loops-like distribution networks of pipes with known node fluid consumptions. Fluid in these networks is usually natural gas for distribution in the municipalities, water in waterworks or hot water in district heating system, air in the case of ventilation systems in buildings or mines, etc. Since, the resistances in these networks depend of flow, problem is not linear like in electrical circuits, and iterative procedure must be used. In both version of the Hardy Cross method, in original and in the improved one, initial results of calculation in iteration procedure is not flow, but rather the correction of flow. Unfortunately, these corrections should be added to or subtracted from a flow calculated in previous iteration according to complicate algebraic rules. After the here presented node-loop method, final results in each of the iterations is flow directly rather than flow correction. In that way complex algebraic scheme for sign of flow correction is avoided, while the final results still remain unchanged. Numbers of required iterations for the same results are comparable with the improved Hardy Cross method.

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

An inverse aeroacoustic problem for a helicopter rotor combined with aerodynamic constraint is proposed based on Ffowcs Williams and Hawkings equation in subsonic. The rotor noise includes thickness noise and loading noise when quadrupole noise is neglected. Thickness noise is related to geometry and motion conditions. Loading noise is related to the pressure on the wall. Therefore, the equation between pressure on the wall and far-field noise can be established, thus the pressure on the wall can be obtained by solving this equation. Since this equation is an ill-posed, the singular value decomposition combined with the regulation method is applied and the aerodynamic constraint is taken into account. The direct noise prediction is verify firstly and then the inverse problem is solved. The reconstruction pressure is compared to the input data. The result is in good agreement with the input value. At the same time, the influence of interference noise is also considered. Under low signal-to-noise ratio, the reconstruction result is also reasonable.

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

Energy transition is a major structural change in the whole social system, and the energy system must be changed globally to replace fossil fuels. Hydropower is one of the largest renewable energy in the world. However the involuntary resettlees due to the construction of hydropower projects are suffering from being far away from their native land, losing the land cultivated for generations and the houses they live in, and losing the social relationship network based on geography and blood ties. Based on the system evaluation theory of reservoir resettlement and referring to relevant research findings, this paper constructs a comprehensive evaluation index framework for assessing the implementation effect of the PostRelocation Support (PReS) policy. The research region is located in Zhijin County, Bijie City, Guizhou Province, China. Accordingly, a combined method of a structural equation model and a fuzzy comprehensive evaluationary model is used in this paper to analyze the implementation of the PReS policy. The results show that the total score of implementing effects of the PReS policy is 4.4, with dramatic significance. The subindex scores of the resettlers’ family income, living conditions, and production conditions; the local economy; and social stability are 4.3, 4.6, 4.4, 4.6, and 4.3, respectively, with dramatic significance. This paper has analyzed and summarized the successful practices of implementing the PReS policy for reservoir resettlers in three dimensions: poverty alleviation, beautiful home construction and accelerating rural revitalization. Research shows that China's rural reservoir resettlers' PReS policy has been more effective in restoring the livelihoods of reservoir resettlers.

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

This paper applied the space-time generalized finite difference scheme for solving the nonlinear dispersive shallow water waves as the modified Camassa−Holm equation, modified Degasperis-Procesi equation, Fornberg-Whitham equation, and its modified form. The proposed meshless numerical scheme was composed of the space-time generalized finite difference method, the two-step Newton-Raphson method, and the time-marching method. The space-time approach can treat the temporal derivative as one of the spatial derivatives. This numerical technique enables all the partial derivatives in the governing equation can be discretized by a spatial discretization method, and the mixed derivative can efficiently deal with using the proposed meshless numerical scheme. The space-time generalized finite difference method is advanced from the Taylor series expansion and the moving-least square method. The numerical discretization process is only related to functional data and weighting coefficients on the central node and its nearby nodes. Thus, the matrix system composed of nonlinear algebraic equations will be a sparse matrix and can be efficiently solved by the two-step Newton-Raphson method. Furthermore, the time-marching method was utilized to proceed with the space-time domain along the time axis. In this paper, several numerical examples were tested to verify the capability of the proposed space-time generalized finite difference scheme.

The Suter curves for Wh and Wm characteristics of collected and the first time presented Four-quadrant (4Q) diagrams of 11 radial pump-turbine models with different specific speeds (nq=24.34, nq=24.8, nq=27, nq=28.6, nq=38, nq=41.6, nq=41.9, nq=43.83, nq=50, nq=56, and nq=64.04) are given in the paper, as well as the Suter curves for 2 pump models (nq=25, and nq=41.8) which were already published in the literature. These 11+2 curves were analyzed to establish a certain universal law of behavior in dependence on the specific speed. For the determination of existing laws in behavior, the fitting procedure using the Regression and Spline methods was used. The paper presents a research plan and structures that include: data collection of four-quadrant diagrams for models of pump-turbines and pumps with different specific speeds (nq), the procedure of recalculation of Four-quadrant diagrams of the models into Suter curves for Wh and Wm characteristics, the definition of the optimal point for the pump and turbine operating mode in pump-turbine models for different specific speeds, and developing numerical models in the MATLAB program to obtain the Universal Equation for the Wh and Wm characteristics. The scientific contribution of this paper is the firstly published original mathematical curve named Universal Equation for the Wh and Wm characteristics for radial pumps and pump-turbines. Application of the equation has been demonstrated at the pumping station where two radial pumps are installed. The calculation of transient processes was performed using the numerical model developed by the authors in the mathematical program MATLAB. Comparison of the transition process results has been made for the two cases - when input data in the numerical model have been firstly used with the values of Suter curves for Wh and Wm characteristics obtained by recalculation from the Four-quadrant operating characteristics (Q11, n11, M11) of model’s specific speed, and then secondly with the values of the Suter curves for Wh and Wm characteristics obtained from the Universal Equation.

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

Due to the ongoing global warming on the Earth, permafrost degradation has been extensively taking place, which poses a substantial threat to civil and industrial facilities and infrastructure elements, as well as to the utilization of natural resources in the Arctic and high-latitude regions. In order to prevent the negative consequences of permafrost thawing under the foundations of constructions, various geophysical techniques for monitoring permafrost have been proposed and applied so far: temperature, electrical, seismic and many others. At the same time, non-stationary electromagnetic methods seem to have significant potential and a number of important practical advantages. We propose a cross-borehole exploration system for the highest localization of target objects in the cryolithozone. A novel mathematical apparatus for three-dimensional modeling of transient electromagnetic (TEM) signals by the vector finite element method has been developed. The original combination of the latter, the Sumudu integral transform and artificial neural networks makes it possible to examine spatially heterogeneous objects of the cryolithozone with a high contrast of geoelectric parameters, significantly reducing computational costs. We have studied the sensitivity of the TEM signals to the boundary between thawed and frozen rocks depending on the inter-borehole distance and spatial orientations of the transmitters and receivers. Numerical simulation results of the TEM monitoring of industrial facilities located on permafrost are considered. The formation of a talik has been shown to significantly manifest itself in the measured electromagnetic responses, which enables timely prevention of industrial disasters and environmental catastrophes.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

The streptavidin and biotin interaction is one of the strongest non-covalent interactions in nature. As a result, this non-covalent interaction has been of great interest when it comes to biochemical assays, diagnosis of diseases, and cell-targeted drug delivery. Past research has proven that biotin-streptavidin is useful in biosensor development to improve the detection of a system when conjugated to nanoparticles. This study aims to prove that streptavidin-coated nanoparticles can be conjugated with biotinylated antibodies using the primary-secondary method to non-invasively detect adenocarcinoma in-vitro. While the use of nanoparticles is not uncommon to the diagnostics area of scientific research, the technique this research aims to investigate is a non-invasive one, utilizing the primary-secondary method. Specifically, the increased stability of fluorophores when bound to antibodies as opposed to nanoparticles directly can be indicative of the particles conjugated through the primary-secondary method’s ability to specifically bind to overexpressed transferrin receptors in the A549 cell line. In this paper, streptavidin-coated nanoparticles were conjugated with biotinylated anti-transferrin receptor antibodies and AlexaFluor-488 secondary antibodies were used to enable fluorescence-based detection. The efficiency of these particles were observed quantitatively through a plate reader and qualitatively through a fluorescence microscope. I demonstrated that these nanoparticles are able to specifically bind to the target proteins in this study. These findings contribute to the field of nanoparticle diagnostics and can be extended to different diseases caused by overexpression of proteins in the future. While this was conducted in-vitro, conjugates can be prepared to detect cancer in-vivo and can be tested with magnetic relaxometry in the future.

Due to the increase in the emission of greenhouse gases, the hydrologic cycle is being altered on the daily basis. This has affected the variations in relations of intensity, duration, and frequency of rainfall events. Intensity Duration Frequency (IDF) curves describe the relationship between rainfall intensity, rainfall duration and return period. IDF curves are one of the most often applied implements in water resource engineering, in areas such as for operating, planning and designing of water resource projects, or for numerous engineering projects aimed at controlling floods. In particular, IDF curves for precipitation answer problems of improper drainage systems or conditions and extreme characters of precipitation which are the main cause of floods in Nyabugogo catchment. This study aims to establish Rainfall IDF empirical equations, curves and hydrological discharge (predicted peak rate of runoff (Qlogy)) equations for eight Districts that will be used for designing an appropriate and sustainable hydraulic structures for controlling flood to reduce potential loss of human and aquatic life, degradation of water, air and soil quality and property damage and economic lessen caused by flood in Nyabugogo catchment. However Goodness of Fit tests revealed that Gumbel’s Extreme-Value Distribution method appears to have the most appropriate fit compared with Pearson type III distribution for validating the Intensity-Duration-Frequency curves and equations through the use of daily annual for each meteorological station. The findings of the study show that the intensity of rainfall increases with a decrease in rainfall duration. Additionally, a rainfall of every known duration will have a higher intensity if its return period is high, while the predicted peak rate of runoff (Qlogy) increases also with an increase in the intensity of rainfall.

The inverse finite element method (iFEM) is a novel method for reconstructing the full-field displacement of structures by discrete measurement strain. In practical engineering applications, the accuracy of iFEM is reduced due to the positional offset of strain sensors during installation, and errors in structural installation. Therefore, coarse and fine two-stage calibration (CFTSC) method is proposed to enhance the accuracy of the reconstruction of structures. Firstly, the coarse calibration is based on a single-objective particle swarm optimization algorithm to optimize the displacement-strain transformation matrix related to the sensor position. Secondly, as selecting different training data can affect the training effect of self-constructed fuzzy networks, this paper proposes to screen the appropriate training data based on residual analysis. Finally, the experiments of the wing integrated antenna structure verify the efficient of the method on the reconstruction accuracy of the structural body displacement field.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

This work presents the results of a comprehensive physico-chemical and biological study of hu-mic substances samples – an extract of humic and fulvic acids. The performed loss on drying test showed a 22 times different dry matter content between EHS and FA. The morphology and dis-tribution of particles in the dry residue of the samples assessed using the methods of optical and digital microscopy demonstrated differences in the qualitative features of the microstructures of their surfaces and granulometries. Shimadzu X-ray fluorescence spectrometry revealed Si (8.1 and 1.7%), P (33.5 and 2.7%), S (4.3 and 59.5%), K (1.35 and 2.5%), Ca (10.9 and 3.2%), Mn (0.27 and 0.06%), Fe (11 and 0.05%), Cu (0.16 and 0.45%), Zn (0.06 and 0.02%) in the dry residues of the EHS and FA samples, respectively. A high intensity of the X-ray fluorescence signal for Fe atoms in the EHS sample was demonstrated. The FT-IR spectra for EHS and FA are characterized by simi-lar vibration frequencies that are characteristic of the chromone derivatives (1-benzopyran-4-one). The UV absorption spectrum is characterized by max = 281 nm for FA. The EHS solution showed a fluorescence maximum at em = 560 nm at ex = 280 nm. Using the DLS method, nanoparticles of 1 nm and 200 nm were detected in EHS and FA diluted solutions, which are likely to condition the biochemical and physical properties of humic acids. Using the Spiro-tox-test method, the absence of the toxic effect of humic acids on the cell model of ciliates Sp. am-bigua was established. When the cell model was incubated in a solution of a toxicant of the fluo-roquinolone group, a decrease in toxicity was demonstrated when diluted with the EHS solu-tion. The results of the study of the antiviral activity of EHS and FA showed that the study ob-jects in the culture of Vero-E6 cells, in doses non-toxic to cells, suppress the reproduction of the SARS-CoV-2 virus both in the study of the virucidal effect and in the study of the antiviral activ-ity according to the therapeutic and prophylactic model scheme of injection. The results obtained suggest that standardized drugs based on humic acids may open up new perspectives in their biomedical application as antiviral drugs.

Background: Developing an efficient and standardized method to isolate and characterize adipose-derived stem cells (ASCs) from the stromal vascular fraction (SVF) of the adipose tissue for clinical application represents one of the major challenges in cell therapy and tissue engineering. Methods: In this study, we proposed an innovative, non-enzymatic protocol to collect clinically useful ASCs within freshly isolated SVF from adipose tissue by centrifugation of the infranatant portion of lipoaspirate and to determine the characteristic cytofluorimetric pattern, prior to in vitro culture. Results: The SVF yielded a mean of 73,32 \pm\ 10,89% cell viability evaluated with CALCEINA-FITC, i.e. cell-permeant dye. The ASCs were positive for PC7-labeled mAb anti-CD34 and negative for both PE-labeled mAb anti-CD31 and APC-labeled mAb anti-CD45. The frequency of ASCs estimated according to the panel of cell surface markers used was 51,06%\ \pm 5,26% versus the unstained ASCs subpopulation that was 0,74%\pm0,84% (P<0.0001). The ASCs events/\muL were 1602,13/\muL \pm 731,87/\muL. Conclusion: Our findings suggested that ASCs found in freshly isolated adipose SVF obtained by centrifugation of lipoaspirate can be immunophenotypically identified with a basic panel of cell surface markers. These findings aimed to provide standardization and contribute to reducing the inconsistency on reported cell surface antigens of ASC derived from the existing literature.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

Every firm is devoted to polishing and fine-tuning its maintenance strategy. More exactly, when we develop robust and efficient preventive and conditional maintenance approaches, our objective is to combine performance and robustness to increase maintenance decision-making. This, in turn, leads to a reduction in system failures and a subsequent drop in related expenses. This impulse drives the origin of this essay: to provide fresh criteria that allow us to improve and optimize maintenance techniques. Furthermore, our study has been realistically utilized via the deployment of condition-based maintenance (CBM) techniques, which are commonly regarded as a critical lever that allows firms to gain a competitive advantage in the context of the fourth industrial revolution. Combining both perfect and imperfect maintenance actions into CBM strategies appears to be an effective technique to obtain high economic performance and robustness in the maintenance strategies of the companies. Following this idea, we propose and optimize in this paper a set of criteria enabling the combined assessment of the mean economic performance and the resilience of various kinds of maintenance techniques. The advantage of the proposed criterion is that it adapts to different types of maintenance strategies and provides access to a simple and relevant evaluation model. Thanks to this new criterion, we will be able to choose the better maintenance strategies that have more performance and robustness between these strategies for a system with more or less stable behavior. The Monte Carlo Method is incorporated into the comparative assessment of maintenance methods, adding a layer to the evaluation of the performance and robustness of each adaptation in decision-making.

Synchronous homopolar machines (SHM) with excitation winding on the stator have attracted the attention of researchers for many decades due to their high reliability. They are used in a variety of applications such as aircraft and railway generators and traction motors. At the same time, the three-dimensional structure of their magnetic circuit makes the problem of their analysis and optimization challenging. This problem becomes even more complicated when considering an SHM with hybrid excitation, with ferrite magnets in the rotor slots. The article proposes a mathematical procedure for optimizing a synchronous homopolar generator with hybrid excitation based on the single-criterion Nelder-Mead method and two-dimensional finite element analysis (FEA). The use of the Nelder-Mead method compared to multicriteria methods and 2D FEA compared to 3D FEA makes possible to significantly reduce the computational burden. As a result of optimization, the power loss and torque ripples of the generator are significantly reduced. The article also compares the characteristics of synchronous homopolar generators with and without ferrite magnets.

For bounded unit interval, we propose a new Kumaraswamy generalized (G) family of distributions from a new generator which could be an alternate to the Kumaraswamy-G family proposed earlier by Cordeiro and de-Castro in 2011. This new generator can also be used to develop alternate G-classes such as beta-G, McDonald-G, Topp-Leone-G, Marshall-Olkin-G and Transmuted-G for bounded unit interval. Some mathematical properties of this new family are obtained and maximum likelihood method is used for estimating the family parameters. We investigate the properties of one special model called a new Kumaraswamy-Weibull (NKwW) distribution. Parameter estimation is dealt and maximum likelihood estimators are assessed through simulation study. Two real life data sets are analyzed to illustrate the importance and flexibility of this distribution. In fact, this model outperforms some generalized Weibull models such as the Kumaraswamy-Weibull, McDonald-Weibull, beta-Weibull, exponentiated-generalized Weibull, gamma-Weibull, odd log-logistic-Weibull, Marshall-Olkin-Weibull, transmuted-Weibull, exponentiated-Weibull and Weibull distributions when applied to these data sets. The bivariate extension of the family is proposed and the estimation of parameters is given. The usefulness of the bivariate NKwW model is illustrated empirically by means of a real-life data set.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

Mechanical engineering plays an important role in the design and manufacture of medical devices, implants, prostheses, and other medical equipment, where the machining of bio-compatible materials have a special place. There are a lot of different conventional and non-conventional types of machining of biocompatible materials. One of the most frequently used methods is milling. The first part of this paper considers the optimization of machining parameters for minimizing surface roughness in milling biocompatible alloy Ti-6Al-4V. With four factors (cutting speed, feed rate, depth of cut, and cooling/lubricating method), each having three levels, the full factorial design implies 81 experiments have to be carried out. Using the Taguchi method, the experiment number was reduced from 81 to 27 runs through an orthogonal design. According to the analysis of variance (ANOVA), the most significant parameter for surface roughness is feed rate. In the second part possibilities of different ML techniques to create a predictive model for average surface roughness using previously created small dataset are explored. Several ML technologies and techniques that can deal successfully with small dataset were explored. The best results show commonly used machine learning algorithm Random Forest that is widely used in regression problems.

In this study, a numerical simulation of fluid flow through railway ballast in the time domain is presented, providing a model for unsteady-state flow. It is demonstrated that the position of the free surface with respect to time can also be used to solve the steady flow case. The effect of ballast fouling is included in the model to capture the realistic behavior of railway ballast, which is critical to understanding the impact of flooding. A thorough comparison with a range of previous studies, including theoretical and experimental approaches, is made and very close agreement is obtained. The significant impact of ballast fouling on fluid flow and its potential consequences for railway infrastructure are highlighted by the simulation. Valuable insights into the behavior of water flow through porous media and its relevance to railway ballast management are offered by this study.

In this work the close relation between vorticity and micro-rotation in micropolar flows in Rn (n = 2 or 3) is identified and used to explain the faster decay by t^(-1/2) of the angular velocity of the micro-rotation of fluid particles, as well as establishing its optimality. For this purpose important upper and lower bounds for Leray solutions in homogeneous Sobolev spaces are derived, using the monotonicity approach recently introduced by the authors for dissipative systems in general. Several related results of interest are also given along the discussion.

Image segmentation is a new challenge prob- lem in medical application. The use of medical imaging has become an integral part of research, as it allows us to see inside the human body without surgical intervention. Many researcher have studied brain segmentation. One stage method is used to segment the brain tissues. In this paper, we proposed the multi-stage generative ad- versarial network to solve the problem of information loss in the one-stage. We utilize the coarse-to-fine to improve brain segmentation using multi-stage generative adversar- ial networks (GAN). In the first stage, our model generated a coarse outline for (i) background and (ii) brain tissues. Then, in the second stage, the model generated outline for (i) white matter (WM), (ii) gray matter (GM) and (iii) cerebrospinal fluid (CSF). A good result can be achieved by fusing the coarse outline and refine outline. We conclude that our model is more efficient and accu- rate in practice for both infant and adult brain segmenta- tion. Moreover, we observe that multi-stage model is faster than prior models. To be more specific, the main goal of multi-stage model is to see the performance of the model in a few shot learning case where a few labeled data are available. For medical image, this proposed model can work in a wide range of image segmentation where the convolution neural networks and one-stage methods have failed.

Time evolution operators of a strongly ionizing medium are calculated by a time-dependent unitary transformation (TDUT) method. The TDUT method has been employed in quantum mechanical system composed of discrete states. This method is especially helpful for solving molecular rotational dynamics in quasi-adiabatic regimes because the strict unitary nature of the propagation operator allows us to set the temporal step size large; a tight limitation on the temporal step size ($\delta t <<1$) can be circumvented by the strict unitary nature. On the other hand, in a strongly ionizing system where the Hamiltonian is not Hermitian, the same approach cannot be directly applied because it is demanding to define a set of field-dressed eigenstates. In this study, the TDUT method was applied to the ionizing regime using the Kramers-Henneberger frame, in which the strong-field-dressed discrete eigenstates are given by the field-free discrete eigenstates in a moving frame. Although the present work verifies the method for a one-dimensional atom as a prototype, the method can be applied to three-dimensional atoms, and molecules exposed to strong laser fields.

Working capital management requires a careful attention by the corporate managers because it plays an important role in corporate stability. Social belongingness of managers induced them to learn from their society, colleagues and from overall industrial movement. They also learn from their peers which have more strategical efficiency. In line with these arguments, the objective of current study is to explores the peer influence on corporate working capital management practices. To making analysis, ten-years data (2009-2018) of non-financial publicly listed firms at PSX were collected and the cash conversion cycle (CCC) uses as a proxy variable of working capital management (WCM). To estimate the regression, an econometric technique named the Generalized Method of Moments (GMM) was used. The empirical findings suggest the significant impact of peer WCM on corporate WCM. It also suggests the significant impact of other variables that determine the WCM. This study recommends social learning policy to corporate managers. They can learn from their peers to manage the working capital. Most previous studies discuss the peer influence on investment decisions, corporate cash holding and financing policy, etc., but no study explores such a relationship specifically in the Pakistani non-financial sector data set.

For the problem of poor accuracy of the existing multi-rate simulation methods, this paper proposes a multi rate real-time simulation method based on the Norton equivalent, compared with multi-rate simulation method based on the ideal source equivalent. After the Norton equivalence of the fast subsystem and the slow subsystem, they are obtained simultaneously at the junction nodes. In order to reduce the amount of simulation calculation, the Norton equivalent circuit is obtained by incremental calculation. The data interface between the fast subsystem and the slow subsystem is realized by extrapolation method. For ensuring the real-time performance of the simulation, the method that the slow subsystem calculates ahead of the fast subsystem is given for the slow subsystem with a large amount of calculation. Finally, the AC/DC hybrid power system was simulated on the real-time simulation platform (FRTDS), and the simulation results were compared with the single-rate simulation, which verified the correctness and accuracy of the method.

A new model for risk assessment of urban rainstorm disasters, based on information diffusion method and variable fuzzy sets (IDM-VFS) was proposed. In addition, an integrated index system of urban rainstorm risk was established. In the proposed model, IDM was employed to calculate the classification standards of urban rainstorm risk levels, then the VFS was adopted to assess the dangerousness, sensitivity, vulnerability and comprehensive risk of urban rainstorm disasters. In the present study, the urban rainstorm risk of Jiangsu province was evaluated with the proposed model. The results show that Wuxi, Changzhou, Nanjing and Suzhou have higher dangerousness, due to sustained rainfall and strong rainfall intensity in short duration; Wuxi, Changzhou and Nanjing have higher sensitivity because of lower disaster resistance ability; and Wuxi and Suzhou have higher vulnerability because these cities have higher potential losses in face of urban rainstorm disasters. The comprehensive risk zoning map of urban rainstorm shows apparent regional characteristics: the northwestern cities have lower risk than the southern cities. Moreover, most cities of the Jiangsu province are of the moderate urban rainstorm risk level. The results are consistent with the actual situation of Jiangsu province, and the study can provide some decision-making references for the urban rainstorm management.

In this paper, a local meshless method (LMM) based on radial basis functions (RBFs) is utilized for the numerical solution of various types of PDEs, due to the flexibility with respect to geometry and high order of convergence rate. In case of global meshless methods, the two major deficiencies are the computational cost and the optimum value of shape parameter. Therefore, research is currently focus towards localized radial basis function approximations, as the local meshless method is proposed here. The local meshless procedures is used for spatial discretization whereas for temporal discretization different time integrators are employed. The proposed local meshless method is testified in terms of efficiency, accuracy and ease of implementation using regular and irregular domains.

In this paper, we work with a diffusion-perturbed risk model comprising a surplus generating process and an investment return process. The investment return process is of standard Black-Scholes type, that is, it comprises a single risk-free asset that earns interest at a constant rate and a single risky asset whose price process is modelled by a geometric Brownian motion. Additionally, the company is allowed to purchase noncheap proportional reinsurance priced via the expected value principle. Using the Hamilton-Jacobi-Bellman approach, we derive a second-order Volterra integrodifferential equation which we transform into a linear Volterra integral equation of the second kind. We proceed to solve this integral equation numerically using the block-by-block method for the optimal reinsurance retention level that minimizes the ultimate ruin probability. The numerical results based on light- and heavy-tailed distributions show that proportional reinsurance and investments play a vital role in enhancing the survival of insurance companies. But the ruin probability exhibits sensitivity to the volatility of the stock price.

In this paper, we study the third order semilocal convergence of the Newton-like method for finding the approximate solution of nonlinear operator equations in the setting of Banach spaces. First, we discuss the convergence analysis under ω-continuity condition, which is weaker than the Lipschitz and Hölder continuity conditions. Second, we apply our approach to solve Fredholm integral equations, where the first derivative of involved operator not necessarily satisfy the Hölder and Lipschitz continuity conditions. Finally, we also prove that the R-order of the method is 2p + 1 for any p $\in$ (0,1].

Satellite-based remote sensing technologies are utilized extensively to investigate urban thermal environments under rapid urban expansion. Current MODIS data is, however, unable to adequately represent the spatially detailed information because of its relatively coarser spatial resolution, while Landsat data can’t explore temporally the refined analysis due to the low temporal resolution. In order to resolve this situation, we used MODIS and Landsat data to generate “Landsat-like” data by using the flexible spatiotemporal data fusion method (FSDAF), and then studied spatiotemporal variation of land surface temperature (LST) and its driving factors. The results showed that 1) The estimated “Landsat-like” data have high precision; 2) By comparing 2013 and 2016 datasets, LST increases ranging from 1.8°C to 4°C were measurable in areas where the impervious surface area (ISA) increased, while LST decreases ranging from -3.52°C to -0.70°C were detected in areas where ISA decreased; 3) LST has a strongly negative relationship with the Normalized Difference Vegetation Index (NDVI), and a strongly positive relationship with Normalized Difference Built Index (NDBI) in summer; and 4) LST is well correlated with Building density (BD), in a complex conic mode, and LST may increase by 0.460°C to 0.786°C when BD increases by 0.1. Our findings can provide information useful for mitigating undesirable thermal conditions and for long-term urban thermal environmental management.

This study examines the evolution of the two-factor authentication method and its adaptability to the online education system. Two-factor authentication is a security measure used especially in areas where information such as banking is valuable. Parallel to technological developments, it has developed as much as daily. It aims to take security one step forward because it is composed of two phases. Today, banking, IOT devices, public transport tickets and many other areas are used. Two-factor authentication methods against security attacks in the field of information are also being updated. In recent years, new technologies such as biometric (iris pattern, retinal pattern, etc.) or behavioral biometry (location tracking, walking information, touch speed etc.) were studied. Instead of physically studying somewhere like going to a course in modern society, online trainings become more advantageous. Most of these online trainings are given certificates such as participation certificate, success certificate, etc. The main problem here is whether the person who is being certified is true. In the study conducted in line with these details, there is a proposal for the application of the Mimic Control Method with Sound Intensity (MCMSI) method for on-line training by examining the two-factor authentication techniques up to the day.

The land subsidence occurring in goafs after coal mining is a protracted process. The accurate prediction of long-term land subsidence in goafs relies heavily on the availability of long-term monitoring data. However, the scarcity of continuous long-term land subsidence monitoring data subsequent to the cessation of mining significantly hinders the accurate prediction of long-term land subsidence in goafs. To address this challenge, this study proposes an innovative method based on Interferometric Synthetic Aperture Radar (InSAR) for predicting long-term land subsidence of goafs following coal mining. The proposed method employs a concatenation approach that integrates multiple short-term monitoring data from different coal faces, each with distinct cessation times, into a cohesive and uniform long-term sequence by normalizing the subsidence rates. The method was verified using actual monitoring data from the Yangquan No.2 mine in Shanxi Province, China. Initially, coal faces with same shapes but varying cessation times were selected for analysis. Using InSAR monitoring data collected between June and December of 2016, the average subsidence rate corresponding to the duration after coal mining cessation of each coal face was back-calculated. Subsequently, a function relating subsidence rate to the duration after coal mining cessation was fitted to the data. Finally, the relationship between cumulative subsidence and the duration after coal mining cessation was derived by integrating the function. The results indicated that the relationship between subsidence rate and duration after coal mining cessation followed an exponential function for a given coal face, whereas the relationship between cumulative subsidence and duration after coal mining cessation conformed to the Knothe time function. Notably, after the cessation of coal mining, significant land subsidence persisted in the goaf of the Yangquan No.2 mine for a duration ranging from 5 to 10 years. The cumulative subsidence curve along the long axis of the coal face ultimately exhibited an inclined W-shape. The proposed method enables the quantitative prediction of residual land subsidence in goafs, even in cases where continuous long-term monitoring data are insufficient, thus providing valuable guidance for construction decisions above the goaf.

Search for periodic signals from blazars has become widely discussed topic in recent years. This is because periodic signals bear imprints of the processes occurring near the innermost regions of blazars which are mostly inaccessible to our direct view. Such signals provide insights into various aspect of blazar studies including disk-jet connection, magnetic field configuration and, more importantly, strong gravity near the supermassive black holes and release of gravitational waves from the binary supermassvie black hole systems. In this work, we report detection of a periodic signal in the radio light curves of the blazar J1043+2408 spanning ~10.5 years. We performed multiple methods of time series analysis, namely, epoch folding, Lomb-Scargle periodogram, and discrete auto-correlation function. All three methods consistently reveal a repeating signal with a periodicity of ~563 days. To robustly account for the red-noise processes usually dominant in the blazar variability and other possible artifacts, a large number of Monte Carlo simulations were performed. This allowed us to estimate a high significance (99.9% local and 99.4% global) against possible spurious detection. As possible explanations, we discuss a number of scenarios including binary supermassive black hole system, Lense-Thirring precession, and jet swing and precession.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

In this paper, we will use the maximum likelihood estimation (MLE) and the Bayes methods to perform estimation procedures for the reliability of stress-strength ℜ=P[X>Y] based on independent adaptive progressive censored samples that were taken from the Chen distributions. An approximate confidence interval of ℜ is constructed using a variety of classical techniques, such as the normal approximation of the MLE, the normal approximation of the log-transformed MLE, and the percentile bootstrap (Boot-p) procedure. The Bayesian estimation of ℜ is obtained based on the balanced loss function, which comes in two versions here, the symmetric balanced squared error (BSE) loss function and the asymmetric balanced linear exponential (BLINEX) loss function. When estimating ℜ using the Bayesian approach, all the unknown parameters of the Chen distributions are assumed to be independently distributed and to have informative gamma priors. Further, a mixture of Gibbs sampling algorithm and Metropolis-Hastings algorithm is used to compute the Bayes estimate of ℜ and the associated highest posterior density credible interval. In the end, simulation research are used to assess the general overall performance of the proposed estimators and a real data set is provided to exemplify the theoretical results.

We introduce a novel stochastically correlated two-factor (i.e., bivariate) diffusion process under the square-root format, for which we obtained, analytically, the corresponding solutions for the conditional moment generating functions and conditional characteristic functions. Such solutions recover verbatim those of the uncorrelated case. We believe that the The aforementioned model encompasses a range of processes similar to that produced by a bivariate square-root process in which entries are correlated in the standard way, i.e., via a constant correlation coefficient. Note that, for the latter, closed-form solutions for the conditional characteristic functions are not available. We focus on the financial scenario of obtaining closed-form expressions for the exact price of a zero-coupon bond and Asian option prices via a Fourier cosine series method.

Recent advancements have revolutionized interplanetary spacecraft missions by combining low-thrust propulsion systems with planetary Gravity-Assist (GA) maneuvers. This study investigates/improved a novel dual-step efficient-robust homotopy algorithm, grounded in indirect optimal control principles, to analyze fuel-optimal bang-bang control problems. The methodology integrates efficient techniques, including the homotopic method, compatible normalization, and improved switching function detection, aimed at enhancing optimal convergence in solving low-thrust gravity-assist spacecraft missions. To illustrate practical application, an Earth-to-Jupiter interplanetary scenario utilizing Mars-GA is examined. Results demonstrate the algorithm's superior efficacy in achieving fuel efficiency, robust convergence, and remarkable accuracy compared to existing solutions.

The rate constants of elementary processes in the atom-diatom system O(³P)+H₂(v), including the processes of vibrational relaxation and dissociation, were studied using the quasi-classical trajectory method. All calculations were carried out along the ground potential energy surface (PES) ³A′′ that was approximated by a neural network. Approximation data were obtained using ab initio quantum chemistry methods at the extended multi-configuration quasi-degenerate second-order perturbation theory XMCQDPT2 in a basis set limit. The calculated cross sections of the reaction channels are in good agreement with the literature data. A complete set of state-to-state rate constants was obtained for the metathesis reaction, the dissociation and VT relaxation of the H₂ molecule upon collision with an O atom. According to this data Arrhenius approximations over a wide temperature range were obtained for the thermal rate constants of considered processes. Data obtained on the dissociation constants and VT relaxation of vibrationally excited H₂ molecules can be used in constructing kinetic models describing the oxidation of hydrogen at high temperatures or highly nonequilibrium conditions.

The nine plateau lake watersheds in Yunnan are important ecological security barriers for southwest China, and the prevention and control of landslides are important considerations in the management of these watersheds. Taking Dianchi Lake watershed as a typical study area, this paper puts forward an improved comprehensive process of landslide susceptibility evalua-tion, and discusses the model’s sensitivity regarding susceptibility to landslides. The compre-hensive process is based on the weight of evidence method (WoE) and integrates many analyti-cal techniques, such as cross-validation, multi-quantile cumulative Student’s comprehensive weight analysis, independence tests, step-by-step modeling, ROC analysis and ROC-based sus-ceptibility zoning. This paper established fourteen models, with high accuracy and validity AUC, reaching 0.83-0.87 and 0.85-0.88, respectively. Moreover, according to the susceptibility zoning map compiled using the optimal model, 80% of landslides can be predicted in the very high and high susceptibility zones, which only account for 19.58% of the study area. Finally, the strategies for geological disaster prevention and ecological restoration deployment were put forward, providing great guiding significance for deeply understanding the landslide susceptibility of lake watersheds (Dianchi Lake) in Yunnan Plateau and guiding the planning and deployment of landslide prevention and mitigation activities and ecological restoration in the watershed.

Coastal inundation is recently requiring a significant attention worldwide. The increasing frequency and intensity of extreme events (sea storms, tsunami waves) are highly stressing the coastal envi-ronments, e.g. endangering a large number of residential areas, ecosystems, tourist facilities, and also leading to potential environmental risks. Predicting such events and the generated coastal flooding is thus of paramount importance and can be reached by exploiting the potential of different tools, like remote sensors and numerical modeling. To this aim, a combination is possible between marine radars and wave-resolving propagation models. While instruments like X-band radars are able at precisely reconstructing both wave field and bathymetry within a coastal area that is some kilometers offshore, wave-resolving Boussinesq-type models can reproduce the wave propagation in the nearshore and the consequent coastal flooding. The present work illustrates the reconstruc-tion of coastal data (wave field and seabed depth) conducted using radar signals and a specifically suited data processing, named “Local Method”, and the use of such coastal data to run numerical simulations of wave propagation (using the FUNWAVE-TVD solver) aimed at reproducing coastal inundation over different scenarios. Such scenarios are built using two different European beaches, i.e. Senigallia (Italy) and Oostende (Belgium), and three different directional spreading values, to evaluate the performances in case of either long- or short-crested waves. The overall validation of the methodology, in terms of maximum inundation, shows good performances, especially in case of short-crested wind waves. Furthermore, the application on the Oostende beach demonstrates that the present methodology might work only using open-access tools, i.e. an easy investigation of the coastal inundation and a potential low-cost integration into early warning systems.

The purpose of this study is to apply the convergence-confinement method (CCM) based on the assumption of hydrostatic stress to the surrounding rock excavated in a circular tunnel whose rock mass characteristics meet the requirements of the non-linear Hoek-Brown failure criterion. Based on a consistent and rigorous method of theoretical analysis, a closed-form analytical solution for the stress/displacement of the ground reaction induced by the advancing excavation of the tunnel, especially in the elastic and plastic regions, is derived and investigated under the condition of an isotropic stress state. By taking the value of a confinement loss as an explicit analysis process in an incremental manner, not only is the computationally executable analytical solution achieved, but it can also be performed using a simple spreadsheet. The validity of the analytical solution implemented by the incremental procedure was examined with published data to study the effect of nonlinear failure criteria on the ground reaction curve; in particular the mechanical behavior at the intrados of the tunnel, and the distribution of stress/displacement on the cross-section of the tunnel. A comparison between the published results and the solution proposed in this study, which interprets the closed-form by the incremental procedure, shows consistent and favorable trends.

Coal is an important resource that is closely related to people’s lives and has an irreplaceable role. However, coal mine safety accidents occur from time to time in the process of working underground. To this end, this paper proposes a coal mine environmental safety early warning model to detect abnormalities and ensure worker safety in a timely manner by assessing the underground climate environment. In this paper, the support vector machine (SVM) parameters are optimized using an improved artificial hummingbird algorithm (IAHA), and its safety level is classified by combining various environmental parameters. To address the problems of insufficient global exploration capability and slow convergence of the artificial hummingbird algorithm during iterations, a strategy incorporating Tent chaos mapping and backward learning is used to initialize the population, a Levy flight strategy is introduced to improve the search capability during the guided foraging phase, and then the simplex method is introduced to replace the worst value before the end of each iteration of the algorithm. The IAHA-SVM safety warning model was established using the improved algorithm to classify and predict the safety of the coal mine environment into four classes. Finally, the performance of the IAHA algorithm and the IAHA-SVM model are simulated separately. The simulation results show that the convergence speed and the search accuracy of the IAHA algorithm are improved, and the performance of the IAHA-SVM model has a significant improvement.

Developing new energy is critical to China's green and low-carbon development. And the New Energy Demonstration City Policy (NEDCP) is a vital innovation policy that inspires the development of new energy. Is the NEDCP facilitating green and low-carbon development, if so, how? Employing unbalanced panel data from 2003 to 2017, the impact of NEDCP on green and low-carbon development was studied by using the "difference in difference" (DID) model. We find that this policy can take significantly role. After various robustness tests, our results are still valid. According to the heterogeneity analysis, non-resource and non-old industrial base cities have a greater positive impact from this policy. The mechanism analysis denotes that the positive policy effect works through upgrading the industrial structure and stimulating urban innovation. The substantial empirical evidence presented in this article supports the continued promotion and implementation of new energy demonstration cities.

Serial femtosecond crystallography (SFX) using an X-ray free-electron laser (XFEL) enables determination of room-temperature structures without causing radiation damage. Using an optical pump-probe or mix-and-injection, SFX enables the intermediate state visualization of a molecular reaction. In SFX experiments, serial and stable microcrystal delivery to the X-ray interaction point is vital for reasonable data collection and efficient beam time. The Pohang Accelerator Laboratory X-ray Free Electron Laser (PAL-XFEL) facility established SFX instruments at a nanocrystallography and coherent imaging (NCI) experimental station. Various sample delivery methods, including injection, fixed-target scanning, and hybrid methods, have been developed and applied to collect XFEL diffraction data. Herein, we review the currently available sample delivery methods for SFX at the NCI experimental station at the PAL-XFEL. This article will help PAL-XFEL users access the SFX system for their experiments.

This study presents the B92 Quantum Key Distribution scheme and its optimization and implementation considerations. Simulation software was developed to model and analyze the B92 protocol under varying conditions. Another contribution of this work is investigating how this protocol runs on real quantum computing hardware. New eavesdropping schemes were proposed and modeled.

Cellular redox state is highly dynamic and delicately balanced between constant production of reactive oxygen species (ROS), and neutralization by endogenous antioxidants, such as glutathione. Physiologic ROS levels can function as signal transduction messengers, while high levels of ROS can react with and damage various molecules eliciting cellular toxicity. The redox state is reflective of the cell’s metabolic status and can inform on regulated cell-state transitions or various pathologies including aging and cancer. Therefore, methods that enable reliable, quantitative readout of the cellular redox state are imperative for scientists from multiple fields. Liquid-chromatography mass-spectrometry (LC-MS) based methods to detect small molecules that reflect the redox balance in the cell such as glutathione, NADH and NADPH, have been developed and applied successfully, but because redox metabolites are very labile, these methods are not easily standardized or consolidated. Here we report a robust LC-MS method for the simultaneous detection of several redox-reactive metabolites that is compatible with parallel global metabolic profiling in mammalian cells. We performed a comprehensive comparison between three commercial hydrophilic interaction chromatography (HILIC) columns, and we describe the application of our method in mammalian cells and tissues. The presented method is easily applicable and will enable the study of ROS function and oxidative stress in mammalian cells by researchers from various fields.

Classical k-ratio models, e.g. ZAF and phi(rho z), used in electron probe microanalysis (EPMA) assume a homogeneous or multi-layered material structure, which essentially limits the spatial resolution of EPMA to the size of the interaction volume where characteristic x-rays are produced. We present a new model for characteristic x-ray emission that avoids assumptions on the material structure to not restrict the resolution of EPMA a-priori. Our model bases on the spherical harmonic (PN) approximation of the Boltzmann equation for electron transport in continuous slowing down approximation. PN models have a simple structure, are hierarchical in accuracy and well-suited for efficient adjoint-based gradient computation, which makes our model a promising alternative to classical models in terms of improving the resolution of EPMA in the future. We present results of various test cases including a comparison of the PN model to a minimum entropy moment model as well as Monte-Carlo (MC) trajectory sampling, a comparison of PN-based k-ratios to k-ratios obtained with MC, a comparison with experimental data of electron backscattering yields as well as a comparison of PN and Monte-Carlo based on characteristic X-ray generation in a three-dimensional material probe with fine structures.

The concept of transformative resilience emerges from complex recent literature and represents a way to interpret the potential opportunities to change in vulnerable territories, where a socio-economic change is required. This article extends the perspective of transformative resilience to assessing of the landscape multi-functionality of inland areas, exploring the potentials to identify a network of synergies among the different municipalities able to trigger a process of territorial resilience. A Spatial Decision Support System (SDSS) for multi-functionality landscape assessment aims to support the local actors to understand local resources and multi-functional values of the Partenio Regional Park (PRP) and surrounding municipalities, in the South of Italy, stimulating their cooperation to the management of environmental and cultural sites and the co-design of new strategies of enhancement.

In this work, the problem is considered for eliminating a non-uniform rectilinear smearing of an image by mathematical and computer-based way, for example, a picture of several cars taken with a fixed camera and moving with different speeds. The problem is described by a set of 1-dimensional Fredholm integral equations (IEs) of the first kind of convolution type with a 1-dimensional point spread function (PSF) at uniform smearing and by a set of new 1-dimensional IEs of a general type (not convolution type) with a 2-dimensional PSF at non-uniform smearing. The problem is also described by one 2-dimensional IE of convolution type with a 2-dimensional PSF at uniform smearing and by a new 2-dimensional IE of a general type with a 4-dimensional PSF at non-uniform smearing. The problem for solving Fredholm IE of the first kind is ill-posed (unstable). Therefore, IEs of convolution type are solved by the Fourier transform (FT) method and Tikhonov's regularization (TR), and IEs of general type are solved by the quadrature/cubature and TR methods. Moreover, the magnitude of the image smear Δ is determined by the original “spectral method”, which increases the accuracy of image restoration. It is shown that the use of a set of 1-dimensional IEs is preferable to one 2-dimensional IE in the case of non-uniform smearing. In the inverse problem (image restoration), the Gibbs effect (the effect of false waves) in the image may occur. It can be edge or inner. The edge effect is well suppressed by the proposed technique “diffusing the edges". In the case of an inner effect, it is eliminated with difficulty, but the image smearing itself plays the role of diffusing and suppresses the inner Gibbs effect to a large extent. It is shown (in the presence of impulse noise in an image) that the well-known Tukey median filter can distort the image itself, and the Gonzalez adaptive filter also distorts the image (but to a lesser extent). We propose a modified adaptive filter. A software package was developed in MatLab and illustrative calculations are performed.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

Cogging torque is a pulsating, parasitic and undesired torque ripple intrinsic of the design of a permanent magnet synchronous generator (PMSG), which should be minimized due to its adverse effects: vibration and noise. In addition, as aerodynamic power is low during start-up at low wind speeds in small wind energy systems, the cogging torque must be as low as possible to achieve a low cut-in speed. A novel mitigation technique using compound pre-slotting, based on a combination of magnetic and non-magnetic materials, is investigated. The finite element technique is used to calculate the cogging torque of a real PMSG design for a small wind turbine, with and without using compound pre-slotting. The results show that cogging torque can be reduced by a factor of 48% with this technique, while avoiding the main drawback of the conventional pre-slotting technique: the reduction of induced voltage due to leakage flux between stator teeth. Furthermore, through a combination of pre-slotting and other cogging torque optimization techniques, 84%, cogging torque can be eliminated for a given design.

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

To address the issue of traditional static evaluation models being unable to comprehensively analyse the performance of ultra-supercritical coal-fired units under varying loads, we propose a dynamic comprehensive evaluation model based on the improved Criteria Importance Through Inter-criteria Correlation (CRITIC) method and Entropy Weight Method (EWM). The comprehensive performance evaluation index system of ultra-supercritical coal fired units is constructed by examining the boiler performance, turbine performance, plant power performance, environmental performance, and flexible performance of coal powered units. The CRITIC and EWM methods are used to calculate the weights of the indicators, which are then combined with the static evaluation results. Using a dynamic comprehensive evaluation model, we analysed ultra-supercritical coal-fired units, taking into account time weight. This allowed us to obtain the comprehensive dynamic real-time evaluation value of the units under different loads. The research indicates that the dynamic comprehensive evaluation model, which uses an improved CRITIC and EWM, has significant advantages in improving evaluation accuracy, weight-balanced distribution, and generality. Provides more accurate, reasonable, and reliable evaluation results for practical decision making.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.