The aim of work is to derive an explicit expression for a function of vertical mixing induced by wind-waves. To this end, in the Navier-Stokes equations, a current is decomposed into four constituents: the mean flow, the wave-orbital motion, the wave-induced turbulent and the background turbulent currents. This decomposition allows separating the wave-induced Reynolds stress, Rw, from the background one, Rb. To make a statistical closure for Rw, the Prandtl approach for the background turbulent fluctuations is used that results in an implicit expression for the wave-induced vertical mixing function, Bv. Expression for Bv is specified based on the author’s results for the eddy viscosity found earlier in the frame of the three-layer concept for a wavy air–sea interface, used for modelling wind-drift currents [1]. Finally, the explicit parameterization for Bv(a, u*, z) is found as a linear function in both the wave amplitude at depth z, a(z), and the friction velocity in the air, u*. The linear dependence of function Bv(a) on the wave amplitude provides the enhanced vertical mixing induced by wind–waves in comparison with function Bv(a) having the cubic dependence found in [2], as far as the wind-wave amplitude a(z) decays exponentially with depth.

We propose a new technique to prepare statistically-robust benchmarking data for evaluating chemical transport model meteorology and air quality parameters within the urban boundary layer. The approach employs atmospheric class-typing, using nocturnal radon measurements to assign atmospheric mixing classes, and can be applied temporally (across the diurnal cycle), or spatially (to create angular distributions of pollutants as a top-down constraint on emissions inventories). In this study only a short (<1-month) campaign is used, but grouping of the relative mixing classes based on nocturnal mean radon concentrations can be adjusted according to dataset length (i.e., number of days per category), or desired range of within-class variability. Calculating hourly distributions of observed and simulated values across diurnal composites of each class-type helps to: (i) bridge the gap between scales of simulation and observation, (ii) represent the variability associated with spatial and temporal heterogeneity of sources and meteorology without being confused by it, and (iii) provide an objective way to group results over whole diurnal cycles that separates ‘natural complicating factors’ (synoptic non-stationarity, rainfall, mesoscale motions, extreme stability, etc.) from problems related to parameterizations, or between-model differences. We demonstrate the utility of this technique using output from a suite of seven contemporary regional forecast and chemical transport models. Meteorological model skill varied across the diurnal cycle for all models, with an additional dependence on the atmospheric mixing class that varied between models. From an air quality perspective, model skill regarding the duration and magnitude of morning and evening “rush hour” pollution events varied strongly as a function of mixing class. Model skill was typically the lowest when public exposure would have been the highest, which has important implications for assessing potential health risks in new and rapidly evolving urban regions, and also for prioritizing the areas of model improvement for future applications.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize emissions of volatile organic compounds (VOCs); viz. benzene, toluene, ethylbenzene and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa. Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-hour average concentrations (in µg/m³) of benzene, toluene, ethylbenzene, p-xylene and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario, was found to be 1.1 -1.2 and 110-120 folds higher than the US EPA designated risk severity indicator (1E^-6), respectively. All four TEX compounds recorded the Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001– 0.05, with toluene concentrations being the lowest and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Background: Low-income families often depend on fuels such as wood, coal, and animal dung for cooking. Such solid fuels are highly polluting and are a primary source of indoor air pollutants (IAP). We examined the association between solid fuel use (SFU) and acute respiratory infection (ARI) among under-five children in Afghanistan and the extent to which this association varies by socioeconomic status (SES) and gender. Materials and Methods: This is a cross-sectional study based on de-identified data from Afghanistan’s first standard Demographic and Health Survey conducted in 2015. The sample consists of ever-married mothers with under-five children in the household (n=27,565). We used mixed-effect Poisson regression models with robust error variance accounting for clustering to examine the associations between SFU and ARI among under-five children after adjusting for potential confounders. We also investigated potential effect modification by SES and sex. Additional analyses were conducted using an augmented measure of the exposure to IAP accounting for both SFU and the location of cooking/kitchen (High Exposure, Moderate, and No Exposure). Results: Around 70% of households reported SFU, whereas the prevalence of ARI was 17.6%. The prevalence of ARI was higher in children living in households with SFU compared to children living in households with no SFU (adjusted prevalence ratio [aPR]= 1.10; 95%CI: 0.98, 1.23). We did not observe any effect modification by SES or child sex. When using the augmented measure of exposure incorporating the kitchen’s location, children highly exposed to IAP had a higher prevalence of ARI compared to unexposed children (aPR 1.17; 95% CI: 1.03, 1.32). SES modified this association with the strongest associations observed among children from the middle wealth quintile. Conclusion: The findings have significant policy implications and suggest that ARI risk in children may be reduced by ensuring clean cookstove as well as clean fuels and acting on the socio-environmental pathways.

The search for higher energy efficiency of industrial-scale burners to attain low emission especially Nitrogen Oxide (NOx) has demanded experimental studies that are complemented with Computational Fluid Dynamics (CFD) simulations. While there exist numerous emission control techniques, the passive control technique was the main focus of the present review study. Biodiesel fuel crude palm oil (CPO) was found to reduce emission components, particularly carbon components and particulate matter (PM). Biodiesel CPO has the capability to mitigate cavitation inside the injector’s orifice which contributes to damage reduction on the orifice. Moreover, although cavitation can improve spray atomization and produce finer spray droplets, it also causes damage to the orifice of injectors. Orifice characteristics such as orifice’s diameter and pattern can also reduce cavitation inside the orifice. Orifice’s pattern is divided into cylindrical shape orifice and conical shape orifice. The conical orifice is found to reduce the cavitation inside the orifice while cylindrical orifice was indicated as a highly cavitating orifice. Alternatively, as rapid swirling motion is capable to enhance the fuel and air mixing, a new concept of swirling fuel-air premix inside the injector is invented and it is proven to reduce emissions. It was, however, learned that spray characteristics are still playing an important role in the prediction of combustion performance, particularly droplets Sauter Mean Diameter (SMD) which is a worldwide parameter that needs further investigations in order to predict the fineness of spray production and combustion.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

A critical review of recent work on fuel lubricant interactions is undertaken. The work focusses on liquid fuels used in diesel and gasoline vehicles. The amount of fuel that contaminates the lubricant depends on driving conditions, engine design, fuel type and lubricant type. When fuel contaminates a lubricant, the viscosity of the lubricant will change (it will usually decrease), the sump oil level may increase, there may be a tendency for more sludge formation, there may be an impact on friction and wear, and low speed pre-ignition could occur. The increased use of biofuels (particularly biodiesel) may require a reduction in oil drain intervals, and fuel borne additives could contaminate the lubricant. The move to active regeneration of particulate filters by delayed fuel post-injection and the move to hybrid electric vehicles, and vehicles equipped with stop-start systems will lead to increased fuel dilution. This will be of more concern in diesel engines, since significant fuel dilution could still persist at sump oil temperatures in the range 100-150C (whereas in gasoline engines the more volatile gasoline fuel will have substantially evaporated at these temperatures). It is anticipated that more research into fuel lubricant interactions, particularly for diesel engines, will be needed in the near future.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

Synthetic fuels play an important role in the defossilization of future aviation transport. To reduce the ecological impact of remote airports due to long range transportation of kerosene, a decentralized on-site-production of synthetic paraffinic kerosene is applicable, preferably as near-drop-in fuel or alternatively as blend. One possible solution for such a production of synthetic kerosene is the Power-to-Liquid process. The basic development of a simplified plant layout addressing the specific challenges of a decentralized kerosene production which differ from most current approaches for infrastructural well-connected regions is described. The decisive influence of the Fischer-Tropsch synthesis on the PtL process is shown by means of a steady-state reactor model which was developed in Python and serves as basis for further development of a modular environment able to represent entire process chains. The reactor model is based on reaction kinetics according current literature. The effects of adjustments of the main operation parameters on the reactor behavior are evaluated and the impacts on up- and downstream processes are described. The results prove the governing influence of the Fischer-Tropsch reactor on the PtL process and show its flexibility regarding the desired product fraction output, which makes it an appropriate solution for a decentralized kerosene production.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

The overexploitation of fossil fuels and their negative environmental impact has attracted the attention of researchers worldwide to propose alternatives to produce bioenergy. Microbial fuel cells (MFCs) systems are sustainable biotechnologies that use bacterial activity to break down organic matter while generating bioelectricity. MFCs have bioelectricity from domestic wastewater (DWW), municipal wastewater (MWW), and potato and fruit waste, reducing environmental contamination and decreasing energy consumption and treatment cost. This review focuses on the recent advancements regarding the designs and configurations, the operation mode of MFCs, and their capacity to produce bioelectricity (e.g., 2203 mW/m2) and fuels (i.e., H2: 438.7 mL/g and CH4: 358.7 mL/g, respectively). Besides, this review highlights practical applications, challenges, techno-economic, and life cycle assessments (LCA) of MFCs. Despite MFC's promising biotechnology, great efforts should be made to implement it in real-time and commercialization.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

Computational methods are essential to support and advance nuclear technologies due to the hazards of handling and analysing highly radioactive materials such as spent nuclear fuel (SNF). However, many such methods, including those thatcan predict SNF compositions and decay heat parameters, require expensive, proprietary software, alongside significant programming experience and computational power for utilisation, severely limiting availability of data and hampering research throughput. Although some datasets are available, many are incomplete or only cover certain fuel systems for older reactor types. Research investigating new methods for SNF recycling, for example, requires compositional and decay heat data for fuel systems not covered by extant data, though analogous source data may be available. With this in mind, we have developed a simple, accessible, and flexible method for extrapolation of isotopic, elemental, and decayheat compositions for SNF at discharge and following decay storage before recycling, based on an extant dataset. This semi-empirical method uses physical and mathematical first principles and can be performed using software accessible to all researchers. This provides outputs accurate to within 1% of reference values interpolated within the range of available data for isotopic compositions, with sensible extrapolations at higher burnups beyond those reported, withoverall elemental outputs accurate to within 0.1%of expected totals. In this publication, we present the developmental methodology, some sample data, the present limitations, and options for future development and expansion of functionality.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

The exposure of Mediterranean forests to large wildfires requires mechanisms to prevent and mitigate their negative effects on the territory and ecosystems. Fuel models synthesize the complexity and heterogeneity of forest fuels and allow understanding and modelling of fire behavior. However, it is sometimes challenging to define the fuel type in a structurally heterogeneous forest stand due to the mixture of characteristics from different types and limitations of qualitative field observation and passive and active airborne remote sensing. This can impact the performance of classification models that rely on in situ identification of fuel type as ground-truth, which can lead to a mistaken prediction of fuel types over larger areas in fire prediction models. In this study, a handheld mobile laser scanner (HMLS) system were used to assess its capability to define Prometheus fuel types in 43 forest plots in Aragón (NE Spain). The HMLS system captured the vertical and horizontal distribution of fuel at extremely high resolution to derive high-density three-dimensional point clouds (average: 63,148 points/m2) which were discretized into voxels of 0.05 m3. The total number of voxels in each 5 cm height stratum was calculated to quantify the fuel volume in each stratum, providing the vertical distribution of fuels (m3/m2) for each plot at centimetric scale. Additionally, fuel volume was computed for each Prometheus height stratum (0.60, 2, and 4 m) for each plot. The Prometheus fuel types were satisfactory identified for each plot, which was compared with the fuel type estimated in the field. This led to the modification of the ground-truth in 10 out of the 43 plots, with estimation errors between types 2–3, 5–6, and 6–7. These results demonstrate the ability of HMLS systems to capture fuel heterogeneity at centimetric scales for the definition of fuel types in Mediterranean forests, making them powerful tools for fuel mapping and fire modelling, and ultimately for improving wildfire prevention and forest management.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The disastrous 2017 fire season in Portugal lead to widespread recognition of the need for a paradigm shift in forest and fire management. We focused our study on Alvares, a parish in central Portugal which had 60% of its area burned in 2017, with a large record of historical. We evaluated how different fuel treatment strategies can reduce wildfire hazard in Alvares, through i) a fuel break network with different priorities and ii) random fuel treatments resulting from stand-level management intensification. To assess this, we developed a stochastic fire simulation system (FUNC-SIM) that integrates uncertainties in fuel distribution over the landscape. If the landscape remains unchanged, Alvares will have large burn probabilities in the north, northeast, and center-east areas of the parish that are very often associated with high fire line intensities. The different fuel treatment scenarios decreased burned area between 12.1-31.2%, resulting from 1%-4.6% increases in annual treatment area, and reduced 10%-40% the likelihood of wildfires larger than 5000 ha. On average, simulated burned area decreased 0.22% per each ha treated, and effectiveness decreased with increasing area treated. Overall, both fuel treatment strategies effectively reduced wildfire hazard and should be part of a larger, holistic and integrated plan to reduce the vulnerability of the Alvares parish to wildfires.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

The use of hydrogen fuel cells as a mobile source of electricity might prove to be a keystone in future decarbonization of heavy duty road and marine transport. Due to complex interplay of various physicochemical processes in the fuel cells, further development of these devices will rely on concerted effort of researchers from various fields, e.g. chemistry, physics, electric and mechanical engineering. This results in knowledge gaps which are filled by the information, dispersed in wide range of literature, but rarely covered in a short and condensed form. To address this issue and with the aim of providing a concise and simple explanation of fuel cell operation, we propose a simple educational model of the most relevant processes in the fuel cell, aimed at proper description of causal relations. The derivation of model equations provides an intuitive understanding of electric potentials acting on protons on the microscopic level and relates this knowledge to the common terminology in fuel cell research community, such as catalyst electric overpotential and internal membrane resistance. The results of the model fit well with experimental data, indicating that a simple description, provided in the paper, is sufficient for intuitive understanding of fuel cell operation.

The study within the current research is focused on theoretical assessment of sustainable aviation fuels (SAF) obtained by blending traditional jet fuels Jet A and different liquids (biodiesel and alcohols) from analytical point of view. Within this paper in-depth analysis ofthe physical-chemical properties of Jet A fuel blended with different biodiesels and alcohols has been performed. Also within the blends Aeroshell 500 oil has been added (5% vol.) for ensuring the lubrication of the turbo engine. The blends consists of: Jet Aaviation fuel + biodieselfrom: palm oil, pork fat, sunflower oil and alcohols: methanol, ethanol and butanol. All the 6 liquids have been blended with Jet A in the following percentages: 10, 20 and 30%. Flash point, kinematic viscosity, density, freezing point, elemental analysis and FTIR analysis have been performed for all the liquids: Aeroshell 500, jet A, jet A + 10, 20, 30% biodiesel from waste palm oil, pork fat and waste sunflower oil, jet A + 10, 20, 30% methanol, ethanol and butanol, biodiesels and alcohols. The obtained results shows the influence of each of the blend’s components on the physical-chemical properties of the blends. Based on the physical-chemical analysis of the blends, conclusions on the behavior of the blends during burning and the gaseous pollutants resulting from the burning process can be drawn.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

The increasing global demand for energy and the pressing challenge of environmental pollution necessitates a paradigm shift towards sustainable energy sources. Hydrogen, a viable renewable energy carrier, has the potential to substantially alleviate these concerns. This review offers a comprehensive exploration of the technologies imperative to the production and operation of fuel cell vehicles (FCVs), ranging from various fuel cell types, hydrogen storage methods, fueling station logistics, batteries in hydrogen vehicles, and the emerging influence of artificial intelligence and quantum computing. An analytical overview of global adoption patterns reveals significant geographical disparities, with the United States and South Korea at the forefront of FCV integration, primarily in the form of passenger cars, followed by buses and trucks. Asia emerges as the region with the highest proportion of FCVs. This paper also delves into the diverse challenges facing FCV implementation, shedding light on the essential role of continued investment in the evolution of sustainable transportation systems. Furthermore, it provides insights into the varying contributions of different companies in the field, demonstrating the collective effort required to advance this promising technology. The comprehensive exploration provided in this review aids in understanding the opportunities, challenges, and potential of hydrogen as an integral player in the future of sustainable transportation. The increasing need for energy carriers and the rise of environmental pollution have driven the exploration of renewable energy sources, with hydrogen being a promising option.

To increase the efficiency of fuel processor and HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) combined system, it is essential to improve the efficiency of a fuel processor. In this research, the fuel processor was simulated by Aspen Hysys® simulator, and effect of the various operating conditions on the total efficiency was investigated. Thermal efficiency of the fuel processor increased as the temperature and S/C (Steam to carbon) ratio increased, and the efficiency was higher at the S/C ratio of 3 than at the S/C of 4 at the reformer temperature of 700 ℃ and higher. Under the selected operating conditions of the fuel processor, recycling of unreacted hydrogen from the anode off gas (AOG) of the HT-PEMFC improve the overall efficiency of the combined fuel processer and HT-PEMFC by a factor of 1.28. Operating conditions where the AOG supplied excessive heat than required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

Fossil fuels and carbon origin resources are affecting our environment. Therefore, alternative energy sources have to be established to co-produce energy along with fossil fuels and carbon origin resources until it is the right time to replace them. Microbial Fuel Cell (MFC) is a promising technology in the field of energy production. Compared to the conventional power sources it is more efficient and not controlled by the Carnot cycle. Its high efficiencies, low noise, and less pollutant output could make it revolutionize in the power generation industry with a shift from centrally located generating stations and long-distance transmission lines to dispersed power generation at load sites. In this review, several characteristics of the MFC technology will be highlighted. First, a brief history of abiotic to biological fuel cells and subsequently, microbial fuel cells is presented. Second, the focus is then shifted to elements responsible for the making MFC working with efficiency. Setup of the MFC system for every element and their assembly is then introduced, followed by an explanation of the working machinery principle. Finally, microbial fuel cell designs and types of main configurations used are presented along with scalability of the technology for the proper application.

Air pollution knows no boundaries, which means for a city or a region to attain clean air standards, must not only look at the emission sources within its own administrative boundary, but also at sources in the immediate vicinity and those originating from long-range transport. And there is a limit to how much area can be explored to evaluate, govern, and manage as designated airsheds for cities and larger regions. This paper discusses the need from an official airshed framework for India’s air quality management, urban airsheds designated for India’s 131 non-attainment cities under the national clean air programme, and proposes climatically and geographically appropriate regional airsheds to support long-term planning. Between 28 states, eight union territories, 36 meteorological sub-regional divisions, and six regional meteorological departments, establishing the proposed 15 regional airsheds for integrated and collaborative air quality management across India is a unique opportunity.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

With growing regulations on ship emissions, specifically carbon dioxide and nitrogen oxides, this study emphasizes the critical need for improving the performance of existing ship diesel engines. Focusing on easily modifiable injection conditions within the fuel system, the research aims to enhance combustion characteristics for operational ships. The study provides a concise analysis of the combustion performance improvements achievable in the field. The study employed a range of calculation conditions, spanning from fuel injection pressures of 20 MPa to 160 MPa, injection timing from 15 degrees before top dead center (BTDC) to 5 degrees after top dead center (ATDC), and spray angles varying between 10 degrees and 50 degrees. A comprehensive analysis was conducted, focusing on fuel distribution behavior, combustion dynamics, carbon monoxide (CO) production and extinction, as well as nitrogen oxide (NO) production. This thorough examination aimed to provide insights into the complex interplay of these factors in order to optimize combustion performance in ship diesel engines. The analysis indicated that substantial unburned fuel occurred at injection pressures below 40 MPa and spray angles less than 20 degrees. This issue was significantly mitigated when injection pressures exceeded 80 MPa or a spray angle of 40 degrees was employed. High flame propagation speeds were observed at injection pressures over 80 MPa and injection timings before BTDC 10. Carbon monoxide emissions were notably low when injection pressures exceeded 80 MPa and a 40-degree spray angle was used. Nitrogen oxide emissions were minimized under conditions of injection pressure below 40 MPa, injection timing after BTDC 5 degrees, and a spray angle between 30 and 40 degrees. The study concludes that the most effective injection conditions for concurrently reducing fuel consumption, minimizing incomplete combustion products, and lowering nitrogen oxide emissions in the target engine are optimal when the injection pressure is set at 80 MPa, the injection timing is positioned at 5 degrees before top dead center (BTDC), and the spray angle is maintained at 40 degrees.

Prescriptions for fuels management are universally applied across forest types in British Columbia, Canada, to reduce fire behaviour potential in the wildland-urban interface. Fuel thinning treatments are assumed to reduce the potential for sustained ignition and crown fire initiation by reducing surface fuel loading. We hypothesized that these prescriptions are not appropriate for the coastal wet forests in the Whistler region of the province. Our study measured the efficacy of fuel thinning treatments in four stands located in the Whistler community forest. We examined several in-stand microclimate variables during snow melt in the spring and at the height of fire danger in late summer, at thinned and unthinned locations paired using GIS- analysis. We found that thinning increased the wildfire risk based on the differences between unthinned and thinned areas in the same forest stand.

This study proposes a redesign of asymmetric single-chamber microbial fuel cells (a-SCMFC) with the goal of optimizing energy production. The new approach is based on the introduction of an Intermediate Microfluidic Septum (IMS) as a relatively simple and inexpensive method to opti-mize both electrolyte flow and species transfer inside the devices. SCMFCs with the novel IMS, operated with sodium acetate as the carbon source, demonstrate to enhance the energy recovery (Erec) factor, defined as the ratio between the energy yield and the inner volume of electrolyte. In standard operative conditions, cells with IMS exhibit Erec value of (37±1) J/m3, with respect to (3.0±0.3) J/m3 of control cells. Furthermore, changing sodium acetate concentration the Erec values change accordingly. By monitoring the activity of a-SCMFCs for over one-year, beneficial impact of the IMS on both the initial inoculation phase and the long-term stability of electrical perfor-mance were observed. These improvements suggest the effectiveness of IMS to allow the de-velopment of efficient biofilms, likely due to the reduction in oxygen diffusion towards the anode. Electrochemical characterizations confirm that the presence of the IMS impacts the diffusion processes inside the electrolytic chamber, supporting the hypothesis of a beneficial effect on oxygen diffusion.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Background: Bioaerosol can represent a danger to the health. During SARS-CoV-2 pandemic, portable devices were used in different environments and considered a valuable prevention tool. This study has evaluated the effectiveness of the air treatment device “AEROK 1.0” in reducing microbial, particulate and pollen airborne contamination indoors, during normal activity. Methods: In an administrative room, airborne microbial contamination was measured using active (DUOSAS 360 and MD8) and passive sampling; a particle counter was used to evaluate particle concentrations; a Hirst-type pollen trap was used to assess airborne pollen and Alternaria spores. Statistical analysis was performed using SPSS 26.0; p values <0.05 were considered statistically significant. Results: The airborne bacterial contamination assessed by the two different samplers decreased by 55.54% and 69.13%, respectively. The airborne bacterial contamination assessed by passive sampling decreased by 44.16%. For fungi, the reduction was 38.7% by active sampling. Airborne particles (diameters ≥ 1.0, 2.0 μm) and the ratio of indoor/outdoor concentrations of total pollen and Alternaria spp spores significantly decreased. Conclusions: The results highlight the effectiveness of AEROK 1.0 in reducing airborne contamination. The approach carried out represents a contribution to the definition of a standardized model for evaluating the effectiveness of this type of devices.

A review of desiccant dehumidification technologies for improving air-quality has been presented, especially focusing on alternatives for air conditioning systems for minimizing the Sick Building Syndrome. The principles and types of desiccant wheels, as well as the existing selection software for these types of equipment, were reviewed and comparatively evaluated. The study focuses on the Brazilian context, therefore, information about air condition systems and laws of this country were evaluated. Possible applications of desiccant wheels are also analyzed, such as their integration into cooling cycles and the sensible heat wheel. Finally, several commercial desiccant wheel selection software were evaluated, which are useful in many situations. Nevertheless, it was evidenced that the available softwares are not capable of performing an operation analysis for only a specific period. Therefore, it is essential to create computational tools to select desiccant wheels, considering the data from the different Brazilian regions for a year.

The fuel cell particularly the Proton Exchange Membrane Fuel Cell (PEMFC) is a new energy technology that plays a critical role in achieving market viability. The PEMFC has high power density, zero CO₂ emissions, and high conversion efficiency. However, with uniform distribution of fuel in PEMFC, we can improve the performance and reduce the cost. The PEMFC will be more efficient and effective in terms of renewable energy as a byproduct only water. Metal foam is used as an alternative for the channels in PEMFC. The model of PEMFC was established by using the ANSYS Fluent 3D Model. Then we proposed four configurations of PEMFC. The outcome demonstrates that Case IV provided outstanding performance if it is compared with the other three cases. In terms of power density, Case IV provided a high power density that is double that of Case I. The porosity of metal foam was investigated. The 0.6 porosity value is found as the optimal value. The uniform distribution of the fuel can be achieved at this value which leads to the outstanding current density.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

In Nigeria, the adoption of sustainable biomass for energy generation is on the rise. One crucial factor that affects the efficiency of Biomass utilization is the moisture content. This study investigates the economic impact of moisture at different stages of the wood biomass distribution chain, considering the entire chain. The methodology employed includes a comprehensive literature review, interviews, and economic calculations. By analyzing these factors, this research aims to provide valuable insights into the economics of moisture in wood biomass, contributing to the sustainable development of the Biomass energy sector in Nigeria. Based on the outcomes of this investigation, it has been discovered that the costs associated with moisture content in Nigeria amount to approximately ₦500,000,00 (Five Hundred Thousand Naira only). Utilizing wood Biomass with a moisture content of 32% weight, as opposed to 18% weight, has proven to be more costly. Transportation contributes to a significant portion of this increase, while the reduction in burning efficiency accounts for the remaining half. To further elaborate on these findings, it is crucial to understand that the transportation costs are impacted by the additional weight and volume of biomass with higher moisture content. This necessitates the use of more fuel and resources during transportation, resulting in increased expenses. Additionally, the decreased burning efficiency associated with higher moisture content poses a challenge. It leads to reduced energy output and increased fuel consumption, ultimately impacting the overall economic viability of wood biomass as an energy source. By identifying these factors, this study aims to provide insights into the economic implications of moisture content in the wood biomass distribution chain in Nigeria. These findings can serve as a basis for developing strategies to optimize the use of biomass, reduce costs, and enhance the sustainability of the energy generation process. One of the most convenient and cost-effective solutions to reduce transportation expenses and improve combustion efficiency is through planned air drying of wood biomass. Large-scale power plants typically prefer utilizing wood biomass that has undergone air drying, resulting in a moisture content ranging from 18% to 36% by weight. By implementing planned air-drying techniques, the moisture content of wood biomass can be significantly reduced, thereby decreasing transportation costs. As the biomass becomes lighter and less bulky, transportation requirements are optimized, leading to enhanced efficiency and reduced expenses. Moreover, air-dried wood biomass offers improved combustion characteristics. The reduced moisture content allows for better heat transfer during the combustion process, resulting in higher energy output and increased fuel efficiency. This not only improves the overall economics of utilizing wood biomass but also contributes to a more sustainable and environmentally friendly energy generation system. The application of planned air drying in the wood biomass distribution chain in Nigeria can serve as a practical solution to address the economic challenges associated with moisture content. By adopting this approach, stakeholders can maximize the potential of wood biomass as a renewable energy resource while minimizing costs and promoting sustainable practices.

Accurate fuel mapping plays a crucial role in fire detection and management strategies. This paper presents a method for discriminating between wildfire fuel types by exploiting together remote sensing data and Convolutional Neural Networks (CNN). Specially, a CNN-based classification approach that leverages Sentinel-2 imagery is exploited to accurately classify fuel types into seven preliminary main classes (conifers, broadleaf, shrubs, grass, bare soil, urban areas, and water bodies) with an high accuracy of 0.99$\%$. To further refine the fuel mapping results, subclasses were generated from the seven principals by using biomass and bioclimatic maps. These additional maps provide complementary information about vegetation density and climatic conditions, respectively. By incorporating this information, we align our fuel type classification with the widely used Scott/Burgan fuel classification system. This refinement step allows for a more detailed and comprehensive assessment of fuel types, enhancing the accuracy and effectiveness of fire management efforts, which can be utilized by fire management agencies, policymakers, and researchers for improved fire behavior prediction and mitigation practices. The proposed approach presents a valuable tool for enhancing fire management, contributing to more effective wildfire prevention and mitigation efforts.

Zero-emission trucks for regional and long haul missions are an option for fossil-free freight. The viability of such powertrains and system solutions was studied conceptually in project ESCALATE for trucks with GVW of 40 tonnes and beyond through various prime mover combinations. The study covers battery and fuel cell power sources with different degrees of battery electric as well as H2 and fuel cell operation. As a design basis, two different missions with a single-charge/H2 refill were analysed. The first mission was the VECTO long haul profile repeated up to 750 km, whereas the second was a real 520 km on-road mission in Finland. Based on the simulated energy consumption on the driving cycle, on-board energy demand was estimated, and the initial single-charge operational scenarios were analysed with five different power source topologies. The traction motors of the tractor were dimensioned so that a secondary mission of GVW up to 76 tons on a shorter route can be operated. Based on the powertrain and vehicle model, various infrastructure options for charging and H2 refuelling strategy as well as various operative scenarios with indicative total cost of ownership (TCO) were analysed.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

This research work studies the characteristics of wear and wear resistance of composite powder coatings, deposited by high-velocity oxygen fuel, which contain composite mixtures Ni-Cr-B-Si having different chromium concentrations – 9.9%; 13.2%; 14%; 16% and 20% , at one and the same size of the particles and the same content of the remaining elements. The coating of 20% Cr does not contain B and Si. Out of each powder, composite coatings have been prepared without any preliminary thermal treatment of the substrate and with preliminary thermal treatment of the substrate up to 650оС. The coatings have been tested under identical conditions of dry friction over a surface of solid firmly attached abrasive particles using the tribological testing device „Pin-on-disk“. Results have been obtained and the dependences of the hardness, mass wear, intensity of the wearing process, absolute and relative wear resistance on the Cr concentration under identical conditions of friction. It has been found out that for all the coatings the preliminary thermal treatment of the substrate leads to a decrease in the wear intensity. Upon increasing Cr concentration the wear intensity diminishes and it reaches minimal values at 16% Cr. In the case of coatings having 20% Cr concentration, the wear intensity is increased, which is due to the absence of the components B and Si in the composite mixture, whereupon no inter-metallic structures are formed having high hardness and wear resistance. The obtained results have no analogues in the current literature and they have not been published by the authors.

Firebrands are an important agent of wildfire spread and structure fire ignitions at the wildland urban interface. Bark flake morphology has been highlighted as an important, yet poorly characterized factor in firebrand generation, transport, deposition, and ignition of unburned material. Using pine species where bark flakes are the documented source of embers, we conducted experiments to investigate how bark structure changes in response to diurnal drying. Over a 3-day period in a longleaf pine (Pinus palustris Mill.) stand in Florida, we recorded changes in temperature, moisture content and structure of bark across different facing aspects of mature pine trees to examine the effects of varying solar exposure on bark moisture. We further compared results to bark drying in a pitch pine (Pinus rigida Mill.) plantation in New Jersey. Under all conditions, bark peeled and lifted away from the tree trunk over the study periods. Tree bole aspect and the time of day interacted to significantly affect bark peeling. General temperature increases and moisture content decreases were significantly different between east and west aspects in pitch pine, and with time of day and aspect in longleaf pine. These results illustrate that bark moisture and flakiness is highly dynamic on short time scales, driven largely by solar exposure. These diurnal changes likely influence the probability of firebrand production during fire events via controls on moisture (ignition) and peeling (lofting).

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

The article considers the issues of ensuring operational performance and environmental sustainability of marine diesel engines by using biodiesel fuel. The research was conducted on 5S60ME-C8 MAN-B&W Diesel Group and 6DL-16 Daihatsu Diesel marine diesel engines, which were operated using RMG380 petroleum fuel and B10 and B30 biodiesel fuels. The efficiency of biofuel usage was assessed based on environmental (reduced nitrogen oxide concentration in exhaust gases) and economic (increased specific effective fuel consumption) criteria. It was found out that the use of B10 and B30 biofuels provides reduction of nitrogen oxides concentration in exhaust gases by 14.71–25.13 %, but at the same time increases specific effective fuel consumption by 1.55–6.01 %. Optimum fuel injection advance angles were determined that ensure the best thermal energy, economic and environmental performance of diesel engines. The optimum angle of biofuel supply advance is determined experimentally and should correspond to the limits recommended by the diesel engine operating instructions. It has been proven experimentally that the use of biofuel increases the environmental sustainability of marine diesel engines by 13.75–29.42 %. It increases the diesel engines environmental safety in case of emergency situations, as well as accidental and short-term emissions of exhaust gases with an increased content of nitrogen oxides into the atmosphere - phenomena that are possible in starting modes of diesel engine operation, as well as in modes of sudden load changes. It is the increase in the environmental friendliness of marine diesel engines in the case of using biofuel that is the most positive criterion and contributes to the intensity of biofuel use in power plants of sea vessels.

Plastics have become an indispensable part of modern life today. The global production of plastics has gone up to 299million tones in 2013, which is believed to be increasing in the near future. The utilization of plastics and its final disposal pose a tremendous negative significance impacts on the environment. The aim of this study was to investigate the thermal and catalytic pyrolysis for production of fuel oil from the polyethene plastic wastes. Catalysts used in the experiment were acid activated clay mineral and aluminum chlorides on activated carbon. The clay mineral was activated by refluxing it with 6M Sulphuric acid for 3hours. The experiment was conducted in three different phases: the first phase of the experiment was done without a catalyst where 88mL oil was obtained at a maximum temperature of 39 and heating rates of 12.5, reaction time of 4hours. The second phase involves the use of acid activated clay mineral where 100mL of oil was obtained and heating rates of 12.5 and reaction time of 3hours 30minutes. The third phase was done using aluminium chlorides on activated carbon and 105ml oil was obtained at a maximum temperature of 400 and heating rates of 15.5 reaction time of 3hours 10minutes. From the results, catalytic pyrolysis is more efficient than purely thermal pyrolysis and homogenous catalysis (aluminum chlorides) shows a better result than solid acid catalyst (activated clay minerals) hence saving the energy needed for pyrolysis and making the process more economically feasible.

Real data obtained from ship in operation are processed and analyzed in this paper. The intention was to provide software which would predict ship’s fuel consumption in some future time instant. It is showed that it is possible to develop such software based on numeric fitting of known data. In order to check how well the prediction of future fuel consumption is, we used only the first half of data for obtaining prediction curve. The second part of data was used to compare different prediction curves goodness. Hence, the presented research used actually a “real future data” and forecasted future data, which are used to numerically evaluate goodness of prediction. The research is of interest for companies logistics, to provide adequate fuel for fleet when and where actually needed. It is concluded that there are several prediction functions which satisfy used statistical quality measures.

A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV) coefficient, which expresses the Fuel Consumption (FC) saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT) vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects). The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

Air pollution, particularly fine particulate matter (PM2.5), poses a significant threat to public health, especially in rapidly urbanizing areas like Lagos State. Despite the severity of the issue, there is a lack of comprehensive data on PM2.5 levels and the Air Quality Index (AQI) in Lagos. This study leverages data from AirQo, an innovative air quality monitoring network using low-cost sensors, to provide a detailed assessment of PM2.5 concentrations and AQI across eight locations in Lagos State, Nigeria. This approach offers real-time, continuous monitoring, filling a critical data gap in the region's air quality management efforts. This study uses AirQo data to assess the concentration levels and spatial distribution of PM2.5 and AQI across the selected eight locations. Data on PM2.5 concentrations were obtained from AirQo sensors deployed across the eight strategic locations in Lagos. The spatial distribution of PM2.5 levels and AQI were analyzed, and the results were compared with national and international air quality standards. The findings revealed that PM2.5 levels (minimum – 6.28 µg/m3 (Ikeja) and maximum - 204.68 µg/m3 (Banana Island) in many areas of Lagos exceed annual WHO and national air quality guidelines, indicating significant health risks. The spatial analysis identified pollution hotspots, particularly in densely populated and industrial regions. The data suggested vehicular emissions and industrial activities as major contributors to high PM2.5 levels. This study underscores the severe air quality issues in Lagos State, emphasizing the need for immediate and targeted interventions to mitigate PM2.5 pollution. The use of AirQo sensors proved effective in providing accurate and timely data for air quality assessment. It is recommended that Lagos State implements stricter emission controls, promotes cleaner technologies, and enhances public transportation systems to reduce traffic-related pollution. Additionally, expanding the air quality monitoring network and incorporating more environmental data will provide a more comprehensive understanding of air pollution impacts, thereby facilitating better policy and public health decisions.

Distracted driving is the leading cause of accidents, the cause of these distractions may include drowsiness, using cell phone, smoking a cigarette, etc. The proposed paper aims at monitoring the attentiveness of the driver and alerting the driver when his/her alertness goes below a certain threshold. It uses image processing using OpenCV (Computer Vision) and You Look Only Once (YOLO) algorithm to detect the eyes and object respectively and sounds an alarm when the driver is either drowsy or using his cell phone or smoking a cigarette.

Formaldehyde (HCHO) is harmful to human health and an adequate assessment of its concentrations, both in outdoor and indoor environments, is necessary in the effort of risk mitigation. In this research, ground indoor and outdoor HCHO measurements have been integrated with the analysis of tropospheric total columns obtained by satellite surveys to assess the concentrations of HCHO in a number of environments, exploiting the proximity of a World Meteorological Organization – Global Atmosphere Watch (WMO/GAW) observation site in Calabria, Southern Italy to a National Institute for Insurance against Accidents at Work (INAIL) department in the municipality of Lamezia Terme. Meteorological parameters gathered at the WMO station have also been used to provide additional data and test new correlations. Using statistical significance tests, the study demonstrates the presence of a correlation between indoor and outdoor HCHO concentrations, thus showing that an exchange between indoor and outdoor formaldehyde does occur. Rooms located in the building where indoor measurements took place have also demonstrated degrees of susceptibility to HCHO exposure which are correlated with the orientation of prevailing wind corridors in the area. The new findings constitute an unprecedented characterization of HCHO hazards in Calabria and provide regulators with new tools on how to mitigate formaldehyde-related risks.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The coronavirus disease (COVID-19) pandemic caused by spreading rapidly a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has imposed a unique situation for the humanity. Sao Paulo has reported 124,105 confirmed cases of COVID-19 and 5,623 deaths up to June 14th, being considered the epicenter of the pandemic in Brazil and in South America. Due to the measures for social distancing, there was a drop in the air pollution concentration in Sao Paulo. Starting on March 16th, 2020, we broke 90 days of social distancing into 13 weeks and compared to an equivalent period in 2019. We investigated the air quality improvement during the quarantine period and compared the associated avoided deaths to COVID-19 burden deaths. Nitrogen dioxide (NO₂) was the best indicator of air quality in the analyzed weeks, since its reduction reached 58 %. Our study showed that the 5,623 deaths occurred during the analyzed weeks of quarantine represents an economic health loss of US$ 10.5 billion. In opposite, we observed a significant air quality improvement due to pollutants concentrations’ reductions during the analyzed weeks. Considering PM₁₀, PM_2.5 and NO₂, the decrease of concentration levels respectively avoided 78, 337 and 387 premature deaths and prevented up to US$ 1.5 billion on health costs. These results highlight the importance of continuing to enforce existing air pollution regulations and measures to protect human health both during and after COVID-19 pandemic.

The last decade has seen a significant growth in low-cost air quality monitoring systems (LCAQMS) adoption, mostly driven by the spatial density limitations of traditional regulatory grade networks which restrict their effectiveness in several settings. The EU's regulatory framework advise for deploying one air quality monitoring unit per roughly 170,000 people or 15 square kilometers which is insufficient for capturing high spatio-temporal variance in complex urban scenarios. Often these settings are characterized by distributed emissions in small roads subjected to intense cars traffic, house heating driven emissions and frequently subjected to canyon effects. The Air Heritage project in Portici, funded by the EU's Urban Innovative Actions (UIA) program, addressed these challenges by integrating low-cost sensors with traditional monitoring systems and engaging the community in pervasive measurement strategies. The project highlights the importance of individualized sensor calibration and frequent recalibrations to maintain accuracy. It also showcases the benefits of citizen science approaches, IoT infrastructures, AI components, and geostatistical sensor fusion algorithms for mobile and opportunistic air quality measurements. This paper reports on the lessons learned and experiences from the Air Heritage project, aiming to guide future implementations in similar contexts. By sharing these insights along with the gathered datalake, we aim to inform stakeholders, including researchers, public authorities, and citizens, about effective strategies for deploying and utilizing LCAQMS to enhance air quality monitoring and public awareness.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &amp;0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

We investigated the influence of the fuel change, from pure hydrogen to hydrogen-ammonia mixture at different percentage, on the electrochemical behaviour of 50 mm in diameter Solid Oxide Fuel Cells (SOFC) with sputtered thin buffer layers of Gd doped Ceria, varying the working temperatures from 800°C to 650°C. The results show that the performances of the cells are not affected by the fuel change for the high working temperatures (800°C and 750°C). As an example, a power density value of 802 mW∙cm-2 at 1 A∙cm-2 is found when directly feeding the cell with 8 Nml∙min-1cm-2 of ammonia and with an equivalent flowrate of 12 Nml∙min-1cm-2 of H2. These power density output values are comparable to those obtained in industrial State of Art (SoA) SOFC cells with screen printed buffer layers fed with higher hydrogen flowrates, thanks to the improved electrochemical performances obtained in the case of cells with sputtered thin buffer layers of Gd doped Ceria. At lower working temperatures (700°C and 650°C), slight changes in the electrochemical behaviour of the cells are observed. Nevertheless, also in this temperature range, we obtain an output current density value of 0.54 A∙cm-2 in pure ammonia flowrate of 12 Nml min-1cm-2, at 800 mV and 700°C, equal to the value observed in SoA button cells with industrial screen printed GDC barrier layer fuelled with 16 Nml∙min-1cm-2 of H2. These results pave the way towards the use of innovative SOFC structures with sputtered thin buffer layers fuelled by ammonia.

Alternative fuels have the potential to reduce exhaust emissions in the transportation sector. In this study, the effects of oxygenated fuels on the performance and emissions of a gasoline single-cylinder spark-ignition engine have been investigated experimentally. Experiments were conducted using a DIDACTA-T85 testbed under full load conditions and variable engine speed. Performance tests were performed by measuring the brake torque, brake power, brake mean effective pressure (BMEP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE). The tested fuel blends were G0, E10, A10, and M10. G0 represented the base fuel and pure gasoline. E10, A10, and M10 were represented by a 10% volume of ethanol, acetone, and methanol in gasoline respectively. Results showed that M10 produced better engine performance in terms of brake torque, brake power, and BMEP, while E10 performed better results in terms of BSFC and BTE. A10 gave the lowest value in NOx emission at all engine speeds. On the other hand, it increased the NOX emission for E10 and M10 blends. This study showed that oxygenated fuel blends significantly reduced carbon monoxide emission at all engine speeds whereas carbon dioxide emission was higher at the highest engine speed.

The results from laboratory tests and field tests, available in the open literature for over ten years, despite the announcement of high efficiency translating into increased energy efficiency and such significant ecological advantages, have not so far resulted in widespread use of fuel performance catalysts (FPC) on a global scale. Wishing to explain why the above situation occurred and to verify the operation of catalytic additives for fuels; this article presents the results of research on the effect of using catalytic additives for fuel in a brand new diesel engine. The article contains an analysis of the results of exhaust gas emission tests from the Doosan MD196TI engine. During the tests, the engine was fueled with a typical diesel fuel and the same fuel with the a catalyst additive. The catalyst was added to the liquid fuel in the form of a commercially available product distributed by ProOne company under the name FMAX. The research was carried out in the form of a test, much more developed than the approval test on a stationary braking station in accordance with the requirements of ISO 8178. The article is concluded with a comparative analysis of exhaust gas emission results illustrating the effects of a catalyst in the form of reduction of solid particles, carbon monoxide, hydrocarbons and a slight increase in nitrogen oxide emissions. In addition, the effect of the catalyst depends on the product of thermal (brake) efficiency of the engine and the calorific value (CV) of the fuel used.

Durability and performance of electrochemical energy converters such as fuel cells and electrolysers are not only dependent on the properties and the quality of the used materials. They strongly depend on operation conditions. Variations in external parameters, such as flow, pressure, temperature and, obviously, load can lead to significant local changes of current density, even local transients. The segmented cell technology was developed with the purpose to gain insight into local operation conditions in electrochemical cells, during operation. The operando measurement of the local current density and temperature distribution allows effective improvement of operation conditions, mitigation of potentially critical events and assessment of the performance of new materials. The segmented cell, which can replace a regular bipolar plate in the current state of the technology, can be used as monitoring tool and for targeted developments. This article gives an overview over the development and applications for proton exchange membrane fuel cell of this technology, such as water management or fault recognition. Recent advancements towards locally resolved monitoring of humidity and to current distributions in electrolysers are outlined.

Due to low working temperature, high energy density and low pollution, proton exchange fuel cells have been investigated under different operating conditions in different applications. Using platinum catalysts in methanol fuel cells leads to increasing the cost of this kind of fuel cell which is considered as a barrier to the commercialism of this technology. For this reason, a lot of efforts have been made to reduce the loading of the catalyst required on different supports. In this study, carbon black (CB) and carbon nanotubes (CNT) have been used as catalyst supports of the fuel cell as well as using the double-metal combination of platinum-ruthenium (PtRu) as anode electrode catalyst and platinum (Pt) as cathode electrode catalyst. The performance of these two types of electro-catalyst in the oxidation reaction of methanol has been compared based on electrochemical tests. Results showed that the carbon nanotubes increase the performance of the micro-fuel cell by 37% at maximum power density, compared to the carbon black. Based on thee-electrode tests of chronoamperometry and voltammetry, it was found that the oxidation onset potential of methanol for CNT has been around 20% less than CB, leading to the kinetic improvement of the oxidation reaction. The current density of methanol oxidation reaction increased up to 62% in CNT sample compared to CB supported one, therefore the active electrochemical surface area of the catalyst has been increased up to 90% by using CNT compared to CB which shows the significant rise of the electrocatalytic activity in CNT supported catalyst. Moreover, the resistance of the CNT supported sample to poisonous intermediate species has been found 3% more than CB supported one. According to the chronoamperometry test results, it was concluded that the performance and sustainability of the CNT electro-catalyst show remarkable improvement compared to CB electro-catalyst in the long term.

Kampala is the capital city of Uganda. Over the years the population growth in the city has more than doubled, and this has increased the demand for energy. However, electricity and gas are not only limited in supply but are also expensive for the majority of the households hence the use of charcoal remains the main source of energy. There is little known about the energy situation in big cities of Africa, and Kampala is not an exception. Therefore, we examine the urban nexus amidst energy poverty, vulnerability, and resilience with a focus on; the role of charcoal in the urban Nexus in Kampala Uganda. Literature review and content analysis of scientific materials such as journal articles and reports were done. Charcoal fuel in Kampala and surrounding urban areas does not only facilitate cooking meals and boing water for over 95% of households but also a source of livelihood for many women in the nexus. This process impacts not only on energy use but also the entire water, energy, and food system in the urban nexus. Even though charcoal fuel doubles as a source of household income, it is greatly responsible for most deforestation. Furthermore, charcoal production also accounts for prolonged droughts hence impacting on water and food supply in the nation. Therefore, we propose subsidizing alternatives such as gas and electricity to reduce the complete reliance on charcoal.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

Abstract: This article explores the intricate relationship between environmental degradation, specifically air pollution, and economic growth in the Sultanate of Oman spanning the period from 1990 to 2022. We employ cointegration and vector error correction models to uncover both short- and long-term dynamics in the association between air pollution and economic growth. Fur-thermore, Granger causality analysis is utilized to investigate the causal links between these crucial variables. This data encompasses factors related to environmental quality and various control variables. The empirical results unveil a sustained long-term cointegration connection between the variables. Additionally, our findings highlight a statistically significant positive impact of economic growth and energy consumption on CO2 emissions. Furthermore, the short-term analysis reveals an annual adjustment of approximately 14.1% in N2O emissions dis-equilibrium. The Granger causality study indicates unidirectional causal relationships involving N2O emissions, economic growth, and CO2 emissions. The implications of these findings for Oman's policy landscape are substantial. To effectively reduce greenhouse gas emissions, it is imperative for Oman to establish robust climate change policies. Additionally, the government can play a pivotal role in encouraging and endorsing the use of renewable energy sources, such as green hydrogen, as a promising alternative to traditional oil and gas resources.

As the haze engulfed the Delhi NCR after Diwali there is a panic in public about its causes and consequences. Here are some facts and figures to know the truth behind the scene. Temperature fell down from 24’C on October 31 to 21’C on November 2 as recorded at UPPCB station at sector-125, Noida which is adjacent to Delhi a very strategic location and can be considered as reference point for Delhi-NCR. The details of the study conducted is given below.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

The term Air Quality (AQ) pertains to the standard of air, which has a direct impact on the health and well-being of individuals. It is crucial to maintain high Air Quality (AQ), for better health and productivity. Though most of people spend more time indoors nowadays, it is not to be overlooked that the pollutant concentration in indoor air is directly linked to the outdoor air quality. Due to the changes in occupancy patterns, outdated maintenance of ventilation systems, and structural flaws in buildings, the indoor air is significantly polluted; pollutants emitted outdoors enter indoor air through open windows, ventilation systems and infiltration. In this paper, we have proposed a new technique, DTMCPM (discrete-time Markov chain (DTMC) model for the analysis and forecasting of AQ, using the power method). Specialized sensors and equipment to measure different pollutants, such as particulate matter, ozone, nitrogen dioxide, sulfur dioxide, benzene and toluene, are used to collect data by the Institute of Pakistan Air Quality Monitor in various cities; the data is converted to US EPA standard for all pollutant species. This data is used to calculate the transition matrix, steady-state values and mean return rate for the analysis of IAQ. The calculated and actual return rates have been compared and the proposed model is found to have a low average prediction error of 2.356%.

The analysis focuses on the intensity of energy consumption in the transportation sector, of the oil-rich country, Iran. The study emphasizes the importance of reducing energy consumption in transportation and identifies factors that affect energy efficiency. The research explores the impact of population growth, clean fuels, energy prices, and investment in energy efficiency in the transport sector. Using data from 1979 to 2011, the study estimates a model with the Autoregressive Distributed Lag model and emphasizes the significance of clean and renewable energies in reducing energy intensity. It also discusses the theoretical background, energy intensity factors, production technology, and the role of clean energy sources. The model framework includes variables like energy intensity index, relative energy price, number of cars, investment ratio, and clean energy production. The findings suggest an increasing trend in energy consumption in the transportation sector, highlighting the importance of identifying drivers that affect energy consumption in the sector.

This study investigates the performance and environmental impact of n-butanol blended with Jet-A fuel in turbo-engines, aiming to assess its viability as a sustainable aviation fuel (SAF). The research involves experimental testing of various blends, ranging from low to high concentrations of methanol, to determine their effects on engine performance and emissions. The experimental setup includes comprehensive measurements of engine parameters such as thrust, fuel consumption rates, and exhaust gas temperatures. Emissions of nitrogen oxides (NOx), particulate matter (PM), carbon monoxide (CO), and unburned hydrocarbons (HC) are also analysed to evaluate environmental impacts. Key findings indicate that n-butanol/Jet-A blends can significantly enhance combustion efficiency and reduce emissions compared to conventional Jet-A fuel. Higher n-butanol concentrations lead to improved thermal efficiency and lower NOx and CO emissions. However, PM emissions slightly increase with higher methanol content. The study underscores the potential of n-butanol as a SAF for turbo-engines, highlighting its ability to mitigate environmental impacts while maintaining or improving engine performance. This research supports the feasibility of integrating n-butanol into Jet-A blends for turbo-engine applications, emphasizing its role in achieving more environmentally friendly aviation operations.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

Grill-specific footprints for common fuels/grill types in the USA are estimated from public information and data from a major grill manufacturer. These are a function of both 1) a fuel’s footprint and 2) a grill’s efficiency of cooking. In 2022, grill-specific footprints vary by 9:1. A typical gas grill is highest at 3.6 lb CO2e/grill session, nine times that of a wood-pellet grill, lowest at 0.4 lb. Charcoal briquettes, electricity and super-efficient gas grills come in-between. Pellets are lowest, because they are made from waste wood and their production burden is modest. Electricity has the highest fuel footprint, yet the second-lowest grill-specific footprint, thanks to its high efficiency. Briquettes come in fourth, because their production involves fossil gas, and they contain some fossil coal. Grill efficiency is key for gas (natural gas or propane): a typical gas grill has twice the footprint of a super-efficient one. In 2027, with bio substitution, the super-efficient gas grill would move ahead of pellets. Electricity and charcoal could improve but would still place fifth and sixth. The range of grill-specific footprints could fall to 4.5:1, within a much-lower range, the highest footprint in 2027 almost 60% lower than 2022’s highest.

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

Many contaminant yeast strains able to survive inside fuel ethanol industrial vats show detrimental cell surface phenotypes, such as filamentation, invasive growth, flocculation, biofilm formation and excessive foam production. Previous studies have linked some of these phenotypes to the expression of FLO genes, and the presence of gene length polymorphisms causing the expansion of FLO gene size appears to result in stronger flocculation and biofilm formation phenotypes. We have performed here a molecular analysis of FLO1 and FLO11 gene polymorphisms present in contaminant strains of S. cerevisae from Brazilian fuel ethanol distilleries showing strong foaming phenotypes during fermentation. The size variability of these genes was correlated with cellular hydrophobicity, flocculation and highly foaming phenotypes in these yeast strains. Our results also show that deleting the major activator of FLO genes (the FLO8 gene) from the genome of a contaminant and highly foaming industrial strain avoids problematic foam formation, flocculation, invasive growth and biofilm production by the engineered (flo8∆::BleR / flo8Δ::kanMX) yeast strain. Thus, the characterization of highly foaming yeasts and the influence of FLO8 in this phenotype opens new perspectives for yeast strain engineering and optimization in the sugarcane fuel-ethanol industry.

The purpose of this paper is to evaluate the acceptance and the utilization of GPS/GPRS-based telematics technology in road transport companies registered in Poland. Telematics technologies are essential for management of energy saving and emissions reduction in road transport. It is in line with the European Union policy of sustainable transportation. The evaluation is based on a survey designed and carried out in 2020. The issues concerning the scope of telematics systems utilization as well as the internal and external factors affecting their use are analysed. The methodology is based on Technology Acceptance Model (TAM) and Structural Equation Modelling (SEM). The results are checked for robustness. Based on the results, it can be reasoned that as a result of the COVID19 pandemic, the companies started to use telematics systems more widely than they did before. Furthermore, the companies employing more people recognize the higher usefulness of telematics systems and are motivated to have the systems more than smaller enterprises; however, TAMs estimated separately for small and medium-sized enterprises did not reveal any significant differences in the parameter estimates.

Ammonia produced using renewable hydrogen is being viewed as a promising media for the export of energy from locations rich in renewable energy sources. Solid oxide fuel cells (SOFCs) are efficient devices for converting such exported ammonia back into electricity at the point of use, however investigations on materials and operating regime for direct ammonia fuelled SOFCs are limited. The studies on fuel electrodes tailored specifically for ammonia fuel are limited. In this work, we evaluated the direct ammonia SOFC performance with Silver-Lanthanum Strontium Cobalt Ferrite (Ag-LSCF) composite anode and a novel Palladium (Pd) nanoparticle decorated Silver-Lanthanum Strontium Cobalt Ferrite (Pd-Ag-LSCF) composite anode in the temperature range of 500 °C to 800 °C. It is hypothesized that Palladium nanoparticles in the anode provide hydrogen dissolution and shift the ammonia decomposition reaction towards the right. The cell performance was evaluated with both hydrogen and ammonia as fuels and a clear-cut improvement in the performance was observed with the addition of Pd for both the fuels. The results showed a performance enhancement by 20% and 43% with hydrogen and ammonia fuels respectively from the Pd addition of Ag-LSCF anode. Open circuit voltage (OCV) values of the cells with hydrogen and ammonia fuel recorded over the temperature range of 500 °C to 800 °C indicated the possibility of direct electro-oxidation of ammonia in SOFCs.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

PEM fuel cell is a technology successfully used in the production of energy from hydrogen, allowing the use of hydrogen as an energy vector. It is scalable for stationary and mobile applications. However, the technology demands more research. An important research topic is fault diagnosis and condition monitoring to improve the life and the efficiency and to reduce the operation costs of PEMFC devices. Consequently, there is a need of physical models that let deep analysis. These models must be accurate enough to represent the PEMFC behavior and to allow the identification of different internal signals of a PEM fuel cell. This work presents a PEM fuel cell model that uses the output temperature in a closed loop, so it can represent the thermal and the electrical behavior. The model is used to represent a NEXA Ballard 1.2 kW; therefore it is necessary to fit the coefficients to represent the real behavior. Five optimization algorithms were tested to fit the model, three of them were taken from literature and two were proposed. Finally, the model with the parameters identified was validated with real.