The impact of nanomaterials on lung fluids or on the plasma membrane of living cells has prompted researchers to examine the interactions between nanoparticles and lipid vesicles. Recent studies have shown that nanoparticle-lipid interaction leads to a broad range of structures including supported lipid bilayers (SLB), particles adsorbed at the surface or internalized inside vesicles, and mixed aggregates. Today, there is a need to have simple protocols that can readily assess the nature of structures obtained from particles and vesicles. Here we apply the method of continuous variation for measuring Job scattering plots and provide analytical expressions for the scattering intensity in various scenarios. The result that emerges from the comparison between modeling and experimental measurements is that electrostatics plays a key role in the association, but it is not sufficient to induce the formation of supported lipid bilayers.

A series of Eu³⁺ doped CaSiO₃/SiO₂ nano-phosphor powder of controlled grain size, crystalline structure, and chemical composition were synthesized using the microemulsion technique. XRD profiles of samples sintered over 600 of suggested phase shift from amorphous powder grain to more ordered polycrystalline powder of triclinic type wollastonite, CaSiO₃, with preferred crystal phase orientation of (112) and tetragonal type cristobalites of SiO₂. The grain size, crystallinity, and chemical composition of the host matrix, activator and sensitizer strongly affected both the absorption and emission bands of these samples. The amplitude of both the orange and red emission bands significantly increased with sintering temperature. The emission band is red-shifted with decreasing grain sizes. These bands displayed good sensitivity to ionic concentration of the Si⁴⁺, Ca²⁺, and Eu³⁺. With increasing Ca²⁺ ion concentration both the intensity of the red photoluminescence (PL) band increased and a concentration quenching observed. Increase in Si⁴⁺ ion concentration led to quenching in PL intensity of both the orange and red bands whereas the amplitude of the blue-band slightly increased. With increasing Eu³⁺ ion concentration the red-band initially increased whereas it started decreasing at higher sample concentration. In the presence of Ca²⁺ ion as a sensitizer, the sample showed a remarkable PL property—including—about 100% photon conversion efficiency and a two-fold increase in excitation and emission photons.

Herein, we evaluated the electrophoretic deposition of nanohydroxyapatite/superhydrophilic multiwalled carbon nanotube composites (nHAp/MWCNT) onto stainless steel biomedical alloys for applications in bone tissue engineering. First, nHAp/MWCNT composites were dispersed into 0.042 mol L⁻¹ of Ca(NO₃)₂·4H₂O + 0.025 mol L⁻¹ NH₄H₂PO₄ electrolytes (pH = 4.8) at two different concentrations. Next, a voltage of −2 V was applied using 316L stainless steel as a working electrode and (0.27 cm²), a high-purity platinum coil wire as the auxiliary electrode, and an Ag/AgCl(3 M) electrode was used as the reference electrode. The nHAp/MWCNT composites were characterized by transmission electron microscopy. The deposited nHAp and nHAp/MWCNT films were characterized by profilometry, scanning electron microscopy, X-Ray diffractometry and Raman spectroscopy. Human osteoblast cells were cultivated with the different materials, and in vitro cytotoxicity was evaluated using lactate dehydrogenase (LDH) assay. The osteogenesis process was evaluated by mRNA levels of the three genes that are directly related to bone repair: Alkaline Phosphatase, Osteopontin and Osteocalcin. We showed that rough, crystalline apatite thin films containing phases of nHAp were successfully deposited onto 316L stainless steel alloys. Also, we noticed that nHAp/MWCNT thin films deposited onto 316L stainless steel alloys upregulated the expression of important genes related to bone mineralization and maturation. Our results strongly support the possibility of this new alternative to modify the surface of metallic biomedical alloys to promote bone tissue regeneration.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

This paper presents a study on developing of a new exoskeleton for ankle joint rehabilitation with three degrees of freedom (3 DOFs). The primary attention is paid to the process of designing and modelling the device aimed at restoring the lost functions of joint mobility. The authors carried out a complex analysis of the functional requirements of the exoskeleton based on the research of potential user’s needs, which allowed them to develop a conceptual model of the proposed de-vice. In this study, a prototype of the exoskeleton is designed using modern additive technolo-gies. A prototype of the proposed device underwent virtual testing in conditions maximally close to the real one, which confirmed its effectiveness and comfort of use. The main results of the work indicate the promising potential of the proposed solution for application in rehabilitation practice, especially for patients with ankle joint injuries and diseases.

In recent years, urbanization and industrialization have significantly increased the levels of outdoor noise pollution, affecting the quality of life in residential areas. In Uzbekistan, rapid development in urban centers has led to heightened concerns about the impact of noise on residents' health and well-being. Noise pollution can result from various sources, including traffic, construction, and industrial activities, causing disturbances and potential health issues such as stress, sleep disorders, and cardiovascular problems. Addressing this issue is crucial for creating a healthier living environment. This article explores effective strategies for mitigating the impact of outdoor noise on residential buildings in Uzbekistan.

Exoskeleton technology has been shown to be useful for individuals with spinal cord injury (SCI), potentially facilitating their recovery of motor function and social reintegration. However, studies on the safety and usability of exoskeletons are limited. This study aimed to design a powered exoskeleton for SCI and evaluate its safety and usability. Ten healthy adults participated in this study. The prototype exoskeleton featured an adjustable frame, computer-controlled hip and knee joint actuators, and a gait-trigger sensor. The experimental actions included walking, standing, and sitting, with and without the prototype. Safety outcomes included adverse events, vital signs, numerical rating scale (NRS) scores for pain, discomfort, and fatigue, and prototype-human body clearance. Usability outcomes included donning and doffing times, subjective ratings, gait speed, stride length, and kinematic parameters of hip and knee joint angles. Safety outcomes showed no serious adverse events, stable vital signs, minimal NRS scores, and acceptable clearance. Usability outcomes showed high efficiency and received positive ratings. Kinematic parameters showed significant positive correlations between normal walking and walking with the prototype for both hip and knee joint angles, confirming its effectiveness in assisting walking. However, further device improvements and gait parameter tuning are necessary for future clinical application.

Photovoltaic shading devices (PVSDs) have the dual function of providing shade and generating electricity, which can reduce building energy consumption and improve indoor daylighting levels. This study adopts a parametric performance design method and establishes a one-click simulation process by using the Grasshopper platform and Ladybugtools. The research focuses on the effect of dynamic PVSDs on daylighting and energy consumption in an office building in Qingdao. Through simulation, the study calculates the monthly energy consumption and useful daylight illuminance (UDI) under different inclination angles and installation heights of PVSDs. And the optimal configuration of PVSDs for each month under three dynamic strategies (rotation, sliding, and hybrid) is determined. Additionally, different control strategies and fixed PVSDs are compared to clarify the impact of various control strategies on daylighting and energy consumption. The findings reveal that, compared to no shading, dynamic PVSDs in rotation strategy (with an installation height of 0 m), sliding strategy (with an inclination angle of 20°), and hybrid strategy can achieve energy savings of 32.13%, 47.22%, and 50.38%, respectively. They can increase the annual average UDI by 1.39%, 2.8%, and 3.1%, respectively.

This article analyzes laws, normative reforms and regulations surrounding the practices and mechanisms of control over the consumption, cultivation and commercialization of cannabis. On the one hand, I investigate regulatory practices that deny rights for the consumption of cannabis classified as recreational. On the other hand, I study regulatory practices that extend rights for the production, consumption and commercialization of cannabis classified as medicinal and industrial. The empirical moment is composed of four stages and methodological tools. First, I conduct an analysis of state policies. Then, I analyze nine laws and codes on cannabis regulation from 1970 to the present. Next, I perform five semi-structured interviews. Finally, I develop two life stories of former people deprived of their liberty for cannabis cultivation and trade. In this way, I trace forms of regulation on multiple demands, knowledge, interests and beliefs. This research focuses on state regulation. Cannabis regulatory regimes are conceived as constructions of political, social and economic truths, meanings and rights. In sum, the answer to the question of how collective demands around cannabis are regulated in Ecuador stipulates that state action reinforces stigmatization and criminalization. In addition, it legitimizes moral entrepreneurs and counter-movements around cannabis.

According to the wide variety of internet of things (IoT) devices within smart environments, many challenges face conventional digital forensic investigation (DFI) in smart environments. Challenges in this environment include heterogeneity, distribution, and massive amounts of data, which exceed digital forensic (DF) investigators’ human capabilities to deal with all of these challenges within a short period of time. Furthermore, it significantly slows down or even incapacitates the conventional DFI process. With the increasing frequency of digital crimes, better and more sophisticated DFI procedures are desperately needed, particularly in such environments. Since machine learning (ML) techniques might be a viable option in certain situations, this paper presents the integration of ML into DF. It also explores the potential further use of ML techniques in DF in smart environments to reduce the hard work of human beings, as well what to expect from future ML applications to the conventional DFI process.

Ocean wave energy is a significantly well-liked renewable energy source. The Internet of Things (IoT) offers a great opportunity for development of the ocean wave energy research. The IoT technology significantly enhanced the performance of the ocean wave energy converter (WEC). The data obtained from IoT devices reduce the risk of using WEC. However, Integrating IoT devices with the WEC is a daunting task because controlling the WEC needs real-time data. This paper investigated the performance of WEC and estimate the lifetime of the modules. IoT devices integrated with various sensors determine different parameters and conditions of the ocean. The IoT platform is used for wireless voltmeters, wireless AC current meters, wireless voltage detection, wireless resistance sensors, wireless temperature sensor, wireless accelerometer, wireless pressure meters, and wireless water level sensors to determine the real-time condition of the ocean wave. These devices are also proven to be reliable and accurate.

Prosthetics have come a long way since their inception, and recent advancements in materials science have enabled the development of prosthetic devices with improved functionality and comfort. One promising area of research is the use of auxetic metamaterials in prosthetics. Auxetic materials have a negative Poisson's ratio, which means that they expand laterally when stretched, unlike conventional materials, which contract laterally. This unique property allows for the creation of prosthetic devices that can better conform to the contours of the human body and provide a more natural feel. In this review article, we provide an overview of the current state of the art in the development of prosthetics using auxetic metamaterials. We discuss the mechanical properties of these materials, including their negative Poisson's ratio and other properties that make them suitable for use in prosthetic devices. We also explore the limitations that currently exist in implementing these materials in prosthetic devices, including challenges in manufacturing and cost. Despite these challenges, the future prospects for the development of prosthetic devices using auxetic metamaterials are promising. Continued research and development in this field could lead to the creation of more comfortable, functional, and natural-feeling prosthetic devices. Overall, the use of auxetic metamaterials in prosthetics represents a promising area of research with the potential to improve the lives of millions of people around the world who rely on prosthetic devices.

Laser therapy devices (LTDs) operating with near-infrared laser light are increasingly being used in sports medicine. For several reasons the users cannot evaluate whether or not such devices emit laser beams according to the specifications provided by the manufacturer and the settings of the device. In this study the laser beams from two different LTDs that can be used in sports medicine were thoroughly characterized by measuring the emitted power, pulse shapes and lengths, and spatial intensity distributions using professional, high-fidelity laser measurement technology. This was repeated for three units of each LDT independently to distinguish problems of individual units from potential intrinsic instrument design errors. The laser beams from the units of one LTD agreed with the settings at the device, with the measured average power for these units being within 3.3% of the set power. In contrast, the laser beams from the units of the other LTD showed large deviations between the settings and the actual emitted light. This device came with three laser diodes that could be used independently and simultaneously. The average power differed greatly between the units as well as between the laser diodes within each unit. Some laser diodes emitted essentially no light, which could lead to a lack of treatment of patients. Other laser diodes emitted much more power than set at the device (up to 230%) that could result in skin irritations or burnings of patients. These findings indicate a need for better standardization and consistency of therapeutic laser light sources.

In this paper, a system of searching for optimal paths is developed and concreted on a FPGA. It is based on a memristive emulator, used as a delay element, by configuring the test graph as a memristor network. A parallel algorithm is applied to reduce computing time and increase efficiency. The operation of the algorithm in Matlab is checked beforehand and then exported to two different Intel FPGAs: a DE0-Nano board and an Arria 10 GX 220 FPGA. In both cases reliable results are obtained quickly and conveniently, even for the case of a 300x300 nodes maze.

Mobile health devices are emerging applications that could help deliver point-of-care (POC) diagnosis, particularly in settings with limited laboratory infrastructure, such as sub-Saharan Africa (SSA). The advent of coronavirus has resulted in an increased deployment and use of mHealth-linked POC diagnostics in SSA. We performed a systematic review and meta-analysis to evaluate the accuracy of mobile-linked point-of-care diagnostics in SSA. Our systematic review and meta-analysis were guided by the Preferred Reporting Items requirements for Systematic Reviews and Meta-Analysis (PRISMA). We exhaustively searched PubMed, Science Direct, Google Scholar, MEDLINE, and CINAHL with full-text via EBSCOhost databases from mHealth inception to March 2021. The statistical analyses were conducted using OpenMeta-Analyst software. All 11 included studies were considered for the meta-analysis. The included studies focused on malaria infections, Schistosoma haematobium, Schistosoma mansoni, soil-transmitted helminths, and trichuris trichiura. The pooled summary of sensitivity and specificity estimates were moderate compared to the gold reference standard. The overall pooled estimates of sensitivity, specificity, positive likelihood ratio, negative likelihood ratio and diagnostic odds ratio of mobile-linked POC diagnostic devices were as follows: 0.499 (95% CI: 0.458-0.541); 0.535 (95% CI: 0.401-0.663); 0.952 (95% CI: 0.60-1.324); 1.381 (95% CI: 0.391-4.879); and 0.944 (95% CI: 0.579-1.538), respectively. Evidence shows that mobile-linked POC diagnostics' diagnostic accuracy is presently moderate in detecting infections in sub-Saharan Africa. Future research is recommended to evaluate mHealth devices' diagnostics with excellent sensitivities and specificities in diagnosing diseases in this setting.

During prolonged standing, insufficient calf muscle pumping accompanies venous stasis and hypertension in the lower legs, resulting in valve dysfunction, venous wall problems, and subsequent inflammation. Compression therapy, which includes medical compression stockings (MCS) and mechanical intermittent pneumatic compression (IPC), is one of the most effective therapeutic interventions for treating chronic venous diseases. This study aimed to investigate the safety and efficacy of IPC and MCS, and the optimal protocol of compression therapy for chronic venous disease. This crossover trial was conducted for healthy, long standing workers (>8 h daily) with leg edema and pain. Four groups were established for each visit: group A (resting after work without MCS), group B (resting after work with MCS), group C (IPC after work without MCS), and group D (IPC after work with MCS). The primary outcome was the visual analogue scale (VAS) score for leg pain. The secondary outcomes were leg volume (mL), circumference (cm), extracellular fluid/total body fluid (ECF/TBF), and extracellular water/total body water (ECW/TBW) through bioimpedance analysis. Outcomes were assessed before work (T0), after work (T1), and 60 minutes after intervention (T2). We included 39 healthy volunteers, aged 30.03±7.56 years. All four groups had significantly increased leg pain after work (T0-1) but improved 60 minutes after intervention (T1-2), particularly group C (decreased VAS by 1.9). When leg swelling was compared at T0 and T1, groups A and C showed significant increases in leg volume and circumference, indicating significant work-induced edema, whereas groups B and D showed no change or even a decrease. After interventions, leg volume and circumference significantly decreased in groups A and C, although groups B and C did not show significant improvement. The ECF/TBF and ECW/TBW of all groups decreased after interventions. Leg pain and edema after prolonged standing in healthy adults were safely and effectively improved by IPC. Although MCS also reduced leg edema immediately after work, it did not show significant improvement in leg pain at T0-1–and T1-2, nor in swelling at T1-2.

Smartphone has become one of the most revolutionary devices in the history of computing. With various kinds of applications, the scope of smartphone has been significantly broadened in the past few years including almost every aspect in our daily life. However, due to the limited on-board resources such as CPU, storage, network bandwidth and battery power, smartphones and the mobile network serving them bring new challenges that have not been encountered in the traditional computing and networking environments. This dissertation focuses on the research areas of improving the network architecture and enhancing the current applications on smartphones. It mainly investigates the areas in the following two directions for three representative categories of mobile services. - In the first direction, the dissertation aims to develop new communication models for smartphone Ad-Hoc networks to achieve efficient communication in the proximity. It is motivated by the fact that smartphone Ad-Hoc networks can help improve the current location-based services and propel new applications. Moreover, the new communication models provide complementary alternatives to the traditional infrastructure-based wireless networks. - In the second direction, the dissertation focuses on improving the other two categories of services, cloud storage services and real-time video streaming services for mobile devices. In the field of cloud storage, we introduce a cloud-assisted approach to provide a set of advanced file operations, such as encryption, decryption and compression, on smartphones. Furthermore, by utilizing the on-board Near Field Communication(NFC) module, we develop an algorithm to securely share the files between mobile devices. For the services of real-time video streaming, we propose approaches that identify a user’s status by analyzing the accelerometer data and then, dynamically adjust the buffer mechanism to save network bandwidth on smartphones.

Introduction: The SARS-CoV2 pandemic has led to an worldwide shortage of Personal Protection Devices (PPD) for medical and paramedical personnel. Adaptation of commercially available snorkel masks to serve as full face masks has been proposed. Even not formally approved as PPD, they are publicized on social media as suitable for this use. Concerns about actual protection levels and risk of carbon dioxide (CO₂) accumulation while wearing them for extended periods made us perform a systematic testing of various brands, in order to verify whether they are as safe and effective as claimed. Methods: A ‘fit’ test was performed, analogous to gas mask testing. Respiratory safety was evaluated by measuring end-tidal CO₂ and oxygen saturation while wearing the masks in rest and during physical exercise. Masks were tested with 3D adaptors to mount regular bacterial-viral ventilator filters when available, or with snorkel openings covered with N95/FFP2 cloth. Results: Modified masks performed reasonably well on the fit test, comparable to regular N95/FFP2 masks. Not all ventilator filters are equally protective. For all masks, a small initial increase in end-tidal CO₂ was noted, remaining within physiological limits. Masks with specific adaptors (3D printed or provided by the manufacturer) are safer, have more flexibility and reliability than makeshift adaptations. Conclusions: These masks can offer benefit as a substitute for complete protective gear as they are easier to don and remove and offer full-face protection. They may be more comfortable to wear for extended periods. Proper selection of mask size, fit testing, quality of 3D printed parts and choice of filter are important.

Interferometry is used in magnetic fusion devices to measure the line-1 averaged electron density. It is based on detecting changes in the refractive index of electromagnetic waves traveling through a plasma. The adequate frequency of these electromagnetic waves depends on several limitations. First the maximum expected peak electronic density must be lower than the cutoff density for that frequency. This means that the waves can still propagate through the plasma when the maximum density is reached. In this sense, IR interferometers operating in the infrared región are themost suitable. With such low wavelengths, mechanical vibrations become an important issue and a complementary interferometer to cancel these vibrations must be used. These arrangements are called two color interferometers. In this paper some measurements that were obtained from the TJ-II double color IR FPGA-based processing system that were never published before are shown and analyzed. The line-averaged electron density is computed in real time (100 μs).

Despite multiple classical outcomes arising from the quantum Rayleigh conversions of photons underlying the propagation of optical waves through dielectric media and the ensuing light-matter interactions, this quantum process has been largely ignored. Several of its outcomes are considered in this article from a physical perspective, e.g., inter-quadrature coupling of photons, phase-dependent amplification in optical directional couplers and related polarization rotation, phase-shifting of weak signals in the optically linear regime, location-dependent coupling coefficient for refractive index gratings, etc. A correct identification of these effects will enable useful design and operation of integrated photonic functional devices.

Electrostatic endothelial cell seeding has evolved as an exceptional technique to improve the efficiency of cell seeding in terms of frequency of attached cells and the amount of cell adhesion for the treatment of vascular diseases. In the recent times, both untreated and superhydrophilic thin film nitinol (TFN) have exhibited strong prospect as substrates for creation of small-diameter endovascular grafts due to their hallmark properties of superelasticity, ultra low-profile character, grown hemocompatible oxide layer with the presence of a uniform endothelial layer on the surface. The purpose of the current study is to understand the effects of endothelial cell seeding parameters (i.e., applied voltage, incubation time, substrate chemistry and cell suspension solution) to investigate the cell seeding phenomenon and to improve the cell adhesion and growth on the TFN surface under electrostatic transplantation. Both parallel plate and cylindrical capacitor models were used along with the Taguchi Design of Experiment (DOE) methods to design in vitro test parameters. A novel in vitro system for cylindrical capacitor model was created using a micro flow pump, micro incubation system, and silicone tubings. The augmented endothelialization on thin film nitinol was developed to determine the effect of cell seeding and deployed in a 6 Fr intravascular catheter setup. Cell viability along with morphology and proliferation of adhered cells were evaluated using fluorescent and scanning electron microscopy. Our results demonstrated that the maximum number of cells attached on STFN in the catheter was observed in 5V with the 2 hr exposure of in the cell culture medium (CCM) solution. The condition showed 5V voltage with 0.68×10-6 µC electrostatic charge and 5.11 V·mm-1 electric field. Our findings have first demonstrated that the electrostatic endothelialization on the superhydrophilic thin film nitinol endograft within the catheter prior to the endovascular procedure could enhance the biocompatibility for low-profile endovascular applications.

The introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology is based on the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In such cases, the fact that the material design methods are based on fundamental scientific principles and have been proven in laboratories and through Accelerated Pavement Testing (APT), may be of little influence. However, the general acceptance of new disruptive technologies, e.g. telecommunications and Information Technologies (IT), have been based on the considerable advantages it presented. The same principles are applicable to the general acceptance and use of NME stabilisation/enhancement of materials in the road construction industry. This article is aimed at the practical cost-effective demonstration of the general application of the use of nanos-silane modified emulsions in the construction of the highest order roads, i.e. inter-city multi-lane highways, lower order roads (including Low-Volume-Roads (LVR)) and even local accesses to farms and in villages/townships. The implementation of NME technologies is directly associated with ease of use, time and cost savings and the addressing and reduction of risks applicable to the use thereof.

The physical properties of nano-fertilizers (NFs) are important in determining their performance, efficacy, and environmental interactions. Nano-fertilizers, due to their small size and high surface area-to-volume ratio, enhance plant metabolic reactions, resulting in higher crop yields. The properties of nano-fertilizers depend on the synthesis methods used. The nanoparticle's nutrient use efficiency (NUE) varies among plant species. This review aims to analyze the relationship between the physical properties of NF and their influence on crop performance and nutrient uptake efficiency. The review focuses on the physical properties of NFs, specifically their size, shape, crystalline, and agglomeration. This review found that smaller particle-sized nanoparticles exhibit higher nutrient use efficiency than larger particles. Nano-fertilizer-coated additives gradually release nutrients, reducing the need for frequent application and addressing limitations associated with chemical fertilizer utilization. The shapes of nano-fertilizers have varying effects on the overall performance of plants. The crystalline structure of nanoparticles promotes a slow release of nutrients. Amorphous nano-fertilizers improve the NUE and, ultimately, crop yield. Agglomeration results in nanoparticles losing their nanoscale size, accumulating on the outer surface, and becoming unavailable to plants. Understanding the physical properties of nano-fertilizers is crucial for optimizing their performance in agricultural applications.

The refractive index of a liquid serves as a fundamental parameter reflecting its composition, thereby enabling the determination of component concentrations in various fields such as chemical research, food industry, and environmental monitoring. Traditional methods for refractive index (RI) measurement rely on light deflection angles at interfaces between the liquid and a material of known refractive index. In this paper, the authors present a new differential refractometer for highly sensitive measurement of RI differences between two liquid samples. Using a configuration with two cells equipped with flat parallel plates as measuring elements, the instrument facilitates accurate analysis. Namely, the sensor signals from both the solution and the solvent cuvette are generated simultaneously with one laser pulse, reducing the possible fluctuations of the laser radiation intensity. Our evaluation shows the high sensitivity of RI measurements (< 7 · 106), so this differential refractometer can be proposed not only as a high-sensitivity sensing tool that can be used for mobile detection of nanoparticles in solution samples, but also to determine the level of environmental nano-pollution using water (including rain, snow) samples from various natural as well as industrial sources, thus helping to solve some important environmental problems.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

Anthocyanins (ACNs) have attracted considerable attention for their potential to modulate the immune system. Research has revealed their antioxidant and anti-inflammatory properties, which play a crucial role in immune regulation by influencing key immune cells such as lymphocytes, macrophages, and dendritic cells. Moreover, ACNs contribute to maintaining a balance between proinflammatory and anti-inflammatory cytokines, thus promoting immune health. Beyond their direct effects on immune cells, ACNs significantly impact gut health and the microbiota, essential factors in immune regulation. Emerging evidence suggests that they positively influence the composition of the gut microbiome that enhance the immunomodulatory effects of ACNs. Furthermore, these compounds synergize with other bioactive substances, such as vitamins and minerals, further enhancing their potential as immune-supporting dietary supplements. However, detailed clinical studies must fully validate these findings and determine safe dosages for different populations. Incorporating these natural compounds into functional foods or supplements can revolutionize the management of immune-related conditions. Personalized nutrition and healthcare strategies can be developed to enhance overall well-being and immune resilience by fully understanding the mechanisms underlying their actions. Recent advancements in delivery methods have focused on improving the bioavailability and effectiveness of ACNs, providing promising avenues for future applications.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

In order to effectively utilize red mud, an aluminum industrial waste, the stabilized soil material was developed using nano-SiO2 synergistically modified red mud, and the strength characteristics of the stabilized soil were analyzed to clarify the feasibility of such stabilized soil serves as a road base material. Through different combination schemes, the effects of different nano-SiO2 and cement contents on the strength of the stabilized materials were explored. The test results show that: in the synergistic modification of nano-SiO2 and cement, nano-SiO2 can significantly improve the early unconfined compressive strength of red mud-based stabilized soil; in the synergistic modification of nano-SiO2, gypsum and cement, the 7-d unconfined compressive strength of red mud-based stabilized soil is greater than 2 MPa, which meets the strength requirements of road base materials and shows the superiority of synergism. The nominal stress-strain curves are divided into five stages: compressed and compacted stage, elastic deformation stage, plastic deformation stage, damage deformation stage and residual deformation stage. The macroscopic compressive damage pattern of the specimens shows that the modified red mud-based stabilized soil mostly exhibits brittle damage.

In order to effectively utilize red mud and reduce its occupation of land resources as well as its impact on the environment, experiments were conducted to develop stabilized soil materials using nano-SiO2 synergistically modified red mud and to investigate the curing mechanism of stabilized soil. The unconfined compressive strength, microscopic morphology and curing mechanism of the red mud-based stabilized soil materials with different amounts of modified materials were investigated. The test results show that after 7-days curing, the unconfined compressive strength of red mud-based stabilized soil meets the compressive strength requirement of road base material when nano-SiO2, gypsum and cement are synergistically modified. In such case, the soil structure has the lowest fracture rate and the best structural compactness when the amount of nano-SiO2 is 1%; It is found that the needle-like and columnar calcium alumina in the modified red mud-based stabilized soil increases, and the binding energy of hydration product ions in the modified material is improved; The chemical curing mechanism of modified red mud-based stabilized soil includes hydration reaction, volcanic ash reaction, promotion effect of nano-SiO2, and enhancement effect of gypsum. On this base, a model of early start hydration process of red mud-based stabilized soil promoted by nano-SiO2 is established.

In recent years, graphene has received so much attention because of its superlative properties and its potential to revolutionize electronics especially in VLSI. This study analyzes the effect of single event upset (SEU) in SRAM cell which employs metal-oxide semiconductor type graphene nano-ribbon field effect transistor (MOS-GNRFET) and compares the results respectively with another SRAM cell designed in PTM 10nm FinFET node. Our simulation show there is a change in data stored in the SRAM after heavy ion strike. However, it recovers from radiation effects after 0.46 ns for GNRFET and 0.51 ns for FinFET. Since the degradation observed in Q and Qb of GNRFET SRAM are 2.7X and 2.16X as compared to PTM nano-MOSFET, we can conclude that GNRFET is less robust to single effect upset. In addition, the stability of SRAM can be improved by increasing the supply voltage VDD.

Lipid nanoparticles have an interesting part of drug delivery system. In this study, the modification of the convention nano-lipid based soybean lecithin was demonstrated. Ginger oil derived Zingiber officinale was used along with lecithin, cholesterol and span 80 to fabricate nano-lipid (GL nano-lipid) using thin-film method. Through TEM and confocal microscope, GL nano-lipid exposes the liposome- like morphology. The average size of the resultant nanoparticles was 249.1nm with monodistribution (PDI= 0.021). The ζ-potential of GL nano-lipid was negative as similar to as prepared nano-lipid based lecithin. GL nano-lipid express the highly stable over 60 days of storage at room temperature in term of size, ζ-potential. A shift of pH value from alkaline to acid was detected in lecithin nano-lipid, while with the incorporation of ginger oil, pH value of nano-lipid dispersion was around 7.0. Furthermore, due to the rich of shogaol-6 and other active compounds in ginger oil, the GL nano-lipid is endowed with intrinsic antibacterial feature. In addition, the sulforhodamine B (SRB) assay and live/dead imaging revealed the excellent biocompatibility of GL nano-lipid. Notably, GL nano-lipid was capable to carry the hydrophobic agents as curcumin and perform a pH-dependent release profile. A subsequent characterization are a suitable potential for drug delivery system.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

This paper presents an overview of the principal structural and dynamics characteristics of reverse micelles (RMs) in order to highlight their structural flexibility and versatility, along with the possibility to modulate their parameters in a controlled-manner. The multifunctionality in a large range of different scientific fields is exemplified in two distinct directions: a theoretical model for mimicry of biological microenvironment and practical application in the field of nanotechnology and nano-based sensors. RMs represents a convenient experimental approach that limits the drawbacks of the conventionally biological studies in vitro, while the particular structure confers them the status of simplified mimics of cells by reproducing a complex supramolecular organization in an artificial system. The biological relevance of RMs is discussed in some particular cases referring to the confinement and crowding environment, molecular dynamics of water and cell membrane structure. The use of RMs in different range of applications seems to be more promising due to their structural and compositional flexibility, a high efficiency and selectivity being achieved. The advance in nanotechnology is based on developing new methods of nanomaterials synthesis and deposition. This review highlighting the advantages of using RMs in synthesis of nanoparticles with specific properties and in nano (bio)sensors design.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Cardiopulmonary resuscitation (CPR) is a widely practiced lifesaving skill. Conventional CPR is based on manual chest compressions and delivering mouth-to-mouth breaths. There has been advancement in biomedical technology over the last few decades which has led to the introduction of new techniques and devices in CPR as well. In light of these advancements, we propose SMEAR (Standard, Mechanical, ECMO Assisted, Augmented virtual and Remote) classification system to provide structured overview from traditional to novel methods and devices. The standard or Manual CPR, widely practiced by the general public during out-of-hospital cardiac arrests, combines active chest compressions with or without mouth breathing. However, to enhance CPR’s efficacy, various mechanical devices have been developed, encompassing Active Chest Compression, Passive Decompression, and those integrated with Automated External Defibrillators. Feedback sensor-equipped devices, include the Metronome, Accelerometer, Barometer, and Triaxial Field Induction. Mechanical devices, classified by their compression mechanisms, can be isolated – like the Piston-driven, Load-distributing, and Active Compression-Decompression (ACD) – or combined, as in ACD-ITV (Impedance Threshold Device), ACD-IAC (Interposed Abdominal Compression), and ACD-ITV-EECP (Enhanced External Counter Pulsation). Beyond mechanics, Extracorporeal CPR offers veno-arterial Extracorporeal Membrane Oxygenation in refractory cardiac arrest and can improve outcomes. Augmented Virtual Reality usage in training and provision of CPR is at the early stages. It has the potential of expanded usage in training public to provide high-quality CPR. A provider can be remotely guided step by step via telephone or smartphone applications, ensuring continuous support until professional assistance arrives.

In high-risk railway construction, personal protective equipment monitoring is critical but challenging due to small and frequently obstructed targets. We propose YOLO-EA, an innovative model that enhances safety measure detection by integrating ECA into its backbone's convolutional layers, improving discernment of minuscule objects like hardhats. YOLO-EA further refines target recognition under occlusion by replacing GIoU with EIoU loss. YOLO-EA's effectiveness was empirically substantiated using a dataset derived from real-world railway construction site surveillance footage. It outperforms YOLOv5, achieving 98.9% precision and 94.7% recall, up 2.5% and 0.5% respectively, while maintaining real-time performance at 70.774 fps. This highly efficient and precise YOLO-EA holds great promise for practical application in intricate construction scenarios, enforcing stringent safety compliance during complex railway construction projects.

Background: The use of wearable devices has burgeoned over the past decade, including wearables for infants and young children. Typically, such devices assess a single modality, and few have undergone scientific validation. To address this gap, we developed an infant wearable platform, LittleBeats™, that integrates electrocardiogram (ECG), motion, and audio sensors on a single printed circuit board to permit daylong remote assessments of infants and caregivers in home environments. Objective: Complementing our prior reports focused on LittleBeats™ data collected among infants and children in the home context, our main objective here is to present a technical validation of each sensor modality against established laboratory protocols and gold-standard equipment. Materials and Methods: We conducted five studies, including assessments of (a) interbeat interval (IBI) data obtained from the LittleBeats™ ECG sensor versus the gold-standard BIOPAC among adults (Study 1, N=16) and infants (Study 2, N=5), (b) performance of automated activity recognition (upright vs. walk vs. glide vs. squat ) among adults using accelerometer data obtained from LittleBeats™ versus Google Pixel 1 smartphone (Study 3, N=12), and (c) performance of speech emotion recognition (SER; Study 4, N=8) and automatic speech recognition (ASR; Study 5, N =12) algorithms among adult samples using audio data from LittleBeats™ versus smartphone. Results: Results for IBI data obtained from the LittleBeats™ ECG sensor indicate acceptable mean absolute percent error (MAPE) rates for both the adults (MAPE = 5.29% to 5.97%; Study 1) and infants (MAPE =0.96% to 1.66%; Study 2) across low- and high-challenge sessions, as well as expected patterns of change in respiratory sinus arrythmia (RSA) across sessions. For activity recognition (Study 3), LittleBeats™ data showed good to excellent performance (Accuracy = 89%, F1-score=88%; Cohen’s kappa =.79), although the smartphone outperformed LittleBeats™ by less than 4%. Finally, performance on the SER applied to LittleBeats™ versus smartphone audio data (Study 4) indicated comparable performance, with a matched-pairs test indicating no significant difference in error rates (p=.26). On the ASR task (Study 5), the best performing algorithm yielded relatively low word error rates, although LittleBeats™ (4.16%) versus smartphone (2.73%) error rates are somewhat higher. Discussion: Taken together, results from these controlled laboratory studies conducted predominantly with adults indicate that the LittleBeats™ sensors yield data quality that is largely comparable to those obtained from gold-standard devices and protocols that have been used extensively in prior research. The advantages of the LittleBeats™ platform is the (a) integration of multiple sensors into one platform that was (b) designed specifically for use with infants and young children. Leveraging data from the multiple modalities and fine-tuning postprocessing steps to further increase data quality, combined with assessing data quality among infants and young children in their natural environments, will be key next steps in this research program.

Manual handling tasks, both in daily activities and at work, require high dexterity and the ability to move objects of different shapes and sizes. However, musculoskeletal disorders that can arise due to aging, disabilities, overloading, or strenuous work can impact the natural capabilities of the hand with serious repercussions both in working and daily activities. To address this, researchers have been developing and proving the benefits of wrist exoskeleton., This paper, which is the part II of a study on wrist exoskeletons, presents and summarizes wearable wrist exoskeleton devices conceived for use in rehabilitation, assistance, and occupational fields. Exoskeletons considered within the study are those available either in a prototyping phase or on the market. They can support the human wrist by relieving pain or mitigating fatigue while allowing at least one movement. According to the requirements to be met, the majority have been designed active (80%) for higher force/torque transmission, and soft for better kinematic compliance, ergonomics, and safety (13 devices out of 24, more than 50%). Electric motors (11 devices out of 24, almost 50%) and cable transmission (9 devices out of 24, almost 40%) are the most common due to their simplicity, controllability, safety, power-to-weight ratio, and the possibility of remote actuation. As sensing technologies, position and force sensors are widely used in all devices (almost 90%). The control strategy depends mainly on the application domain: for rehabilitation, CPM (Control Passive Motion) is preferred (35% of the devices), while for assistance and occupational purposes AAN (Assistance-As-Needed) is more suitable (38% of the devices). What emerges from this analysis is that while rehabilitation and training are fields in which exoskeletons have been grown more easily and gained some user acceptance (almost 18 devices of which 4 are available on the market), relatively few devices have been designed for occupational aims (6 of which only 2 are available on the market) due to difficulties in meeting the acceptance and needs of users. In this perspective, as a result of the state-of-the-art analysis, the authors propose a conceptual idea of a portable soft wrist exoskeleton for occupational assistance.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

Environmental pollution by noise is one of the most serious health threats nowadays. The impact of noise on the human body depends not only on the sound level but also on its spectral distribution. Reliable measurements of the environmental noise spectrum are often hampered by the very high price of top quality measuring devices. This paper explores the possibility of using much cheaper audio recorders for frequency analysis. Comparative research were performed in laboratory and field conditions, which showed that, with some limitations, these devices can be useful for the needs of environmental noise frequency analysis. This fact gives an opportunity for reduce the cost of noise analysis experimental work.

The prevalence of chronic diseases is dramatically increasing demand for emergency healthcare. Existing systems rely on patients self-identifying symptoms, causing dangerous delays. This study develops an AI and IoT-powered “digital twin” solution to enable continuous real-time monitoring and timely prediction of diverse medical emergencies. A digital twin is a virtual representation of an individual, modeled using multidimensional physiological data from wearable sensors. Machine learning techniques analyze patterns in this data to identify anomalies and predict emergencies like heart attacks or falls. A key contribution is an optimized ensemble algorithm combining gradient boosted trees, neural networks, and other techniques to accurately detect emergency events. Evaluation on a dataset of 9158 samples shows the digital twin identifies key emergencies with over 90% recall, enabling prevention and rapid response. It allows risk stratification and personalized interventions based on early warnings, circumventing over 2 million avoidable emergency room visits annually. This study demonstrates the feasibility of an integrated, predictive, patient-centric emergency response system enabled by digital twin technology.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

Abstract: Fertility tracking of menstrual cycles during perimenopause with a quantitative hormone monitor is a novel undertaking. Women in regular menstrual cycles have been tracking their fertility using different biomarkers since the 1960’s [1]. Presently, there are newer electronic hormonal devices used to track fertility that provide more exact and objective data to help delineate the fertile time frame of a woman’s cycle. These devices measure quantitative levels of estrogen, luteinizing hormone, progesterone, and follicle stimulating hormone, all of which occur at varying levels during the menstrual cycle. As women advance toward menopause, their cycles vary in length and their hormones fluctuate [2]. In this retrospective analysis, forty-two women aged 40 to 50 tracked their cycles over time and eight of the forty-two women used the quantitative hormonal device. With the use of this device, the perimenopausal period has revealed distinct hormonal cycle characteristics unique to this group of women. It is the purpose of this paper to discuss those cycle characteristics during perimenopause that were found with the use of the quantitative hormonal device.

This study aimed to discuss the combined theoretical and experimental results of elastic properties of the tungsten trioxide films supported on Quartz (YX)/45°/10° resonator, as surface acoustic wave (SAW) device. The SAW system with different thicknesses of WO3 thin films were imaged and structurally characterized by X-Ray diffraction, atomic force and transmission electron microscopy. The deposited WO3 films (100 nm, 200 nm and 300 nm) were crystallized in a single monoclinic phase. The acoustoelectric properties of the SAW system were obtained by combining theoretical simulations with experimental measurements. The modeling of the SAW devices has been performed by the finite element and boundary element methods (FEM/BEM). The theoretical and experimental electrical admittances responses obtained at room temperature gave access to elastic constants. The gravimetric effect of the deposited layers is observed by a resonance frequencies shift to lower values with thicknesses film. Moreover, the acoustic losses are affected by the dielectric losses of the WO3 films, while the resonant frequency decreases almost linearly. SAW devices revealed strong displacement fields with low acoustic losses as a function of WO3 thicknesses. For all the deposited layers, the Young's modulus and the Poisson coefficient obtained are respectively of 8 GPa and 0.5.

We report a micro-ring resonator with adiabatic bends, non contact waveguide heaters and small bend radius. The ring has the lowest reported off resonance loss and can support 8 wavelength division multiplexed channels at 200 GHz spacing. We measure 0.49 nm/mW tuning efficiency and 0.085 dB off resonance loss.

Abstract: The biological process of photosynthesis was critical in catalyzing the oxygenation of Earth’s atmosphere 2.5 billion years ago, changing the course of development of life on Earth. Recently, the fields of applied and synthetic photosynthesis have utilized the light-driven protein-pigment supercomplexes central to photosynthesis for the photocatalytic production of fuel and other various valuable products. The reaction center Photosystem I is of particular interest in applied photosynthesis due to its high stability post-purification, non-geopolitical limitation, and its ability to generate the greatest reducing power found in Nature. These remarkable properties have been harnessed for the photocatalytic production of a number of valuable products in the applied photosynthesis research field. These primarily include photocurrents and molecular hydrogen as fuels. The use of artificial reaction centers to generate substrates and reducing equivalents to drive non-photoactive enzymes for valuable product generation has been a long-standing area of interest of the synthetic photosynthesis research field. In this review, we cover advances in these areas and further speculate synthetic and applied photosynthesis as photocatalysts for the generation of valuable products.

With the widespread of embedded sensing capabilities of mobile devices, there has been unprecedented development of context-aware solutions. This allows the proliferation of various intelligent applications such as those for remote health and lifestyle monitoring, intelligent personalized services, etc. However, activity context recognition based on multivariate time series signals obtained from mobile devices in unconstrained conditions is naturally prone to imbalance class problems. This means that recognition models tend to predict classes with the majority number of samples whilst ignoring classes with the least number of samples, resulting in poor generalization. To address this problem, we propose to augment the time series signals from inertia sensors with signals from ambient sensing to train deep convolutional neural networks (DCNN) models. DCNN provides the characteristics that capture local dependency and scale invariance of these combined sensor signals. Consequently, we developed a DCNN model using only inertial sensor signals and then developed another model that combined signals from both inertia and ambient sensors aiming to investigate the class imbalance problem by improving the performance of the recognition model. Evaluation and analysis of the proposed system using data with imbalanced classes show that the system achieved better recognition accuracy when data from inertial sensors are combined with those from ambient sensors such as environment noise level and illumination, with an overall improvement of 5.3% accuracy.

Biofilm-mediated infection is a major cause of bone prosthesis failure. The lack of molecules able to act in biofilms has driven research aimed at identifying new anti-biofilm agents via chemical screens. However, to be able to accommodate a large number of compounds, the testing conditions of these screenings end up being typically far from the clinical scenario. In this study, we assess the potential applicability of three anti-biofilm compounds (based on natural compounds) as part of implanted medical devices by testing them on in vitro systems that more faithfully resemble the clinical scenario. To that end, we used a competition model based on the co-culture of SaOS-2 mammalian cells and Staphylococcus aureus (collection and clinical strains) on a titanium surface. Additionally, we studied whether these derivatives of natural compounds enhance the previously proven protective effect of pre-incubating the titanium surface with SaOS-2 cells. Out of the three tested leads, one showed the highest potential, and can be regarded as a promising agent for incorporation into bone implants. This study emphasizes and demonstrates the importance of using meaningful experimental models, where potential antimicrobials ought to be tested for protection of biomaterials in translational applications.

Commercial sleep devices and mobile-phone applications for scoring sleep are gaining ground. In order to provide reliable information about the quantity and/or quality of sleep, their performance needs to be assessed against the current gold-standard, i.e. polysomnography (PSG; measuring brain, eye and muscle activity). We here assessed some commercially available sleep trackers, namely; a commercial activity tracker: Mi band (Xiaomi, BJ, CHN), a scientific actigraph: Motionwatch 8 (CamNTech, CB, UK), and a much used sleep application: Sleep Cycle (Northcube, GOT, SE). We recorded 27 nights in healthy sleepers using PSG and these devices. Surprisingly, all devices had very poor agreement with the gold standard. Sleep parameter comparisons revealed that specifically the Mi band and the sleep cycle application had difficulties in detecting wake periods which negatively affected the total sleep time and sleep efficiency estimations. However, all 3 devices were good in detecting the most basic parameter, the actual time in bed. In summary, our results suggest that, to-date; available sleep trackers do not provide meaningful sleep analysis but may be interesting for simply tracking times in bed. A much closer interaction with the scientific field seems necessary if reliable information shall be derived from such devices in the future.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

Research on fall and movement detection with wearable devices has witnessed promising growth. However, there are few publicly available datasets, all recorded with smartphones, that prevent authors to evenly compare their new proposals. Here, we present a dataset of falls and activities of daily living (ADL) acquired with a self-developed device composed of two types of accelerometer and one gyroscope. It consists of 19 ADL and 15 fall types performed by 23 young adults, 15 ADL types performed by 14 healthy and independent participants over 62 years old, and data from one participant of 60 years old that performed all ADL and falls. These activities were selected based on a survey and a literature analysis. We test the dataset with widely used feature extraction and a simple to implement threshold based classification, achieving up to 96~\% of accuracy in fall detection. An individual activity analysis demonstrates that most errors coincide in a few number of activities where algorithms could be focused on. Finally, validation tests with elderly people significantly reduced the fall detection performance of the tested features. This validates findings of other authors and encourages to develop new strategies with this new dataset as benchmark.

The use of New-age (Nano) Modified Emulsions (NME) for the stabilisation of marginal materials for use in the upper-pavement layers of roads have been proven in laboratories, through Accelerated Pavement Tests (APT) and in practice. In addition, material design methods have been developed based on the scientific analysis of granular material mineralogy and the chemical interaction with the binder to design a material compatible NME stabilising agent for naturally available (often marginal) materials. However, the introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology enables the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In practice, few road construction projects are without any problems. The introduction of new-technologies obviously makes it an easy target to blame for any non-related problem that may arise during construction. This article aims to assist in pre-empting, recognising, preventing and resolving material or non-material related construction problems through the correct identification of the cause of the problem and recommending the best, most cost-effective way to correct any deficiencies on site.

Side-chain liquid crystal polymers have been mixed with ferromagnetic particles, and the for-mation of a monodomain in magnetic fields studied. At relatively low concentrations, the presence of ferroparticles substantially speeds up the rate of formation of a monodomain with the magnetic field and at a given concentration of ferrofluid that rate is independent of the magnetic field strength. In this way, rapid formation of a monodomain is possible at magnetic field strengths far lower than required for the liquid crystal polymer alone. This is anticipated to very helpful in the fabrication of devices based on monodomain liquid crystal elastomers. Wide angle x-ray scattering has been used to monitor the formation of the monodomain and small angle x-ray scattering can give some indication of the ferroparticle behaviour. A model is developed to explain the behaviour. The alignment properties of the ferroparticles is related to their ability to form chains under the influence of very low magnetic fields; these chains are of relatively low stability and may become disrupted after long times, high magnetic fields, or high concentrations. In general, the best results for alignment were at volume fractions below 1%, and under these con-ditions there is the potential for producing monodomain samples with improved properties; in particular shape changes with temperature are significantly larger as a result of improved backbone orientation. Experiments involving monodomain formation and director realignment suggest that the presence of ferroparticles results in a modification in the mechanism for alignment development driven by the organisation of the polymer backbone as a consequence of the con-straints offered by the morphology of the chains of ferroparticles.

Bacillus Calmette-Guérin (BCG) immunotherapy has been a cornerstone treatment for non-muscle invasive bladder cancer for decades and still faces challenges, such as severe immune adverse reactions, which reduce its use as a first-line treatment. This review examines BCG therapy’s history, mechanisms, and current status, highlighting how nanotechnology and bioengineering are revitalizing its application. We discuss novel nanocarrier systems aimed at enhancing BCG's efficacy while mitigating specific side effects. These approaches promise improved tumor targeting, better drug loading, and enhanced stimulation of anti-tumor immune responses. Key strategies involve using functional BCG cell wall components and co-delivering BCG with chemotherapeutics to achieve synergistic effects. While most studies remain experimental, this research direction offers hope for overcoming BCG's limitations and advancing bladder cancer immunotherapy. Further elucidation of BCG's mechanisms and rigorous safety evaluations of new delivery systems will be crucial for translating these innovations into clinical practice.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

Soil salinity is seen as a major restriction for crop production, and with water scarcity this problem becomes more complicated. Mulching is crucial to salinity dynamics management by decreasing evaporation with improving the soil’s characteristics. Using chitosan as an eco-friendly biostimulant can enhance plant defense genes during different abiotic stresses. Recently, agricultural research has recognized nanoparticles as a pioneer material due to their distinctive physicochemical features. Therefore, a lysimeter experiment was conducted to investigate the interactive effects of mulching (UNM: un-mulched, WPM: white plastic, RSM: rice straw and SDM: sawdust) and chitosan foliar application (Ch0: control, Ch1: 250 mg chitosan L-1, Ch2: 125 mg nano chitosan L-1, and Ch3: 62.5 mg nano chitosan L-1) on the biochemical soil characteristics and common beans productivity under salt affected soil conditions. Organic mulching (RSM and SDM) treatments significantly improved the soil's organic carbon, available nutrient content, and total count of bacteria. WPM treatment lowered soil EC to 6.63 dS m-1 and increased soil water content to 34.13%. The application of Ch3 caused considerable increases in the plant height, shoot dry weight, root dry weight, grain yield, and nutrient content in the seed. The total fungi count in the soil and Na% in the seed was significantly decreased due to chitosan foliar applications. Moreover, the interactive effect of different mulch materials plus foliar by chitosan applications gave a statistically similar seed yield in both seasons. Overall, this study revealed the potential of the mulching treatments and foliar application of nano chitosan in improved biochemical soil characteristics and common bean productivity under saline soil conditions.

In this paper we introduce the concept of Nano Beta Closure, Nano Beta Interior and study the relationship between them also study some of their properties. Based on these notions we introduced the topological Approach to Decision Making and Its Application in the Medical Field" which describes the use of topological methods in decision-making, specifically through the utilization of nano beta closure and nano beta interior. These mathematical tools are applied in the medical field to improve diagnostic accuracy and aid in treatment planning. The authors demonstrate the effectiveness of this approach through a case study on the diagnosis of Chronic Kidney. The results show that the topological approach using nano beta closure and nano beta interior provides a reliable and accurate method for medical decision-making. Finally, we introduce a medical application for disease groups patients of with chronic kidney. To identify the main causative agent of kidney disease. where using this approach, the medical team can identify the specific areas of the kidney that are affected by the infection, as well as the extent of damage and any potential complications. This information is used to create an individualized treatment strategy that is customized to meet the specific requirements of the patient. and medical history. We write an algorithm that can be a helpful tool for doctors to utilize in diagnosing infection disease Chronic Kidney infections. By utilizing this approach, clinicians can provide accurate diagnoses, develop effective treatment plans, and ultimately improve patient outcomes. finally, we show that fractals hold significant importance in future nano topological generation of the human factor. Their unique properties and self-similar patterns offer insights into the complex organization of biological systems and provide a foundation for designing advanced Nanosystems.

Diabetes mellitus is a cluster of metabolic diseases characterized by hyperglycemia. Since this epidemic growing worldwide, the usage of phototherapeutics to manage diabetes is vital. Coccinia grandis (Aka ivy gourd) belongs to cucumber family is identified as a most effective herb, especially for diabetes and many other disease conditions. Hence, an instant herbal porridge cube incorporating Coccinia grandis leaf powder was produced and sensory acceptability of the porridge was evaluated using trained panelists. The bioactive activity of Coccinia grandis leaf powder showed that 66.77±0.74 mg/g GAE of Total Phenolic Content, 27.65±6.79% of DPPH radical scavenging activity, 5.72% of alpha-amylase inhibition activity and 59.64% of alpha-glucosidase inhibition activity. The effect on postprandial blood sugar levels after consuming the developed porridge was measured using healthy adults and it was observed there was no blood sugar elevation during the 2 hours of time. As a further development, Coccinia grandis leaf extract was nano-encapsulated with food grade Sodium alginate and it was incorporated into the same porridge as a safe delivery method of bioactive compounds. In-vitro digestion assay was conducted and the results show that alpha-amylase inhibition activity for the gastric phase and alpha-glucosidase inhibition activity for the intestinal phase was higher in nano-encapsulated porridge. The study concludes that, consuming nano-encapsulated Coccinia grandis leaf extract with porridge is more beneficial for diabetic patients.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 &amp; N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

The present work is focused on functionalizing Montmorillonite (Mt) with poly dimethyl siloxane (PDMS) to develop a hybrid membrane reactor for the removal of Co (II) and Ni (II) ions from model wastewater samples. The specific surface area of the novel material was found to be 444 m2 /g. X-Ray Diffraction (XRD) and Fourier Transform Infra-Red (FTIR) spectra reveal the formation of exfoliated composite material. The efficiency of this membrane material was determined by subjecting it to continuous filtration experiments. It was able to remove 50% of Co (II) and 75% of Ni (II) ions, respectively, in one cycle of filtration in less than three minutes of operation with a permeate flux rate of 675 L/m2/H and 975 L/m2/H respectively, for both the ions.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

Of course, now we know that quantum mechanics has been a fundamental structure of our world since our universe came into being. However, it has been only a century since the experimental and theoretical discovery of quantum mechanics and its extensions into many implications and applications. In particular, there are implications across many disciplines that most likely will affect education, health, security, etc. Examples are given of the need for starting education as early as possible in schools, the use of nano-robots to deliver drugs targeted to specific molecular sites, to developing new cryptographic systems to safeguard our privacy.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Evaporation studies of water using classical molecular dynamics simulations are largely limited due to its high computational expense. We aim at addressing the computational issues by developing a coarse grain model for evaporation of water on solid surfaces by combining four water molecules into a single bead. Most commonly used mono atomic pair potentials like Lennard Jones, Morse, Mie and three body potential like Stillinger-Weber are optimized using a combination of Genetic algorithm and Nelder-Mead algorithm. Among them, Stillinger-Weber based model shows excellent agreement of density and Enthalpy of vaporization with experimental results for a wide range of temperatures. Further, the new water model is used to simulate contact angle of water and thin film evaporation from surfaces with different wettabilities.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

Aiming at the damage detection and continuous monitoring of high efficiency composite structure, the method of carbon nano sensor embeded in the 3-D braided composite material specimen was put forward and the method of damage location for 3-D braided composite material was described. In this paper, the mechanical and electrical characteristics of carbon nano-fiber were analyzed. Considering the massive data of the health monitoring of composite processing, to ensure that the system has good real-time performance, quaternary matrix Singular Value Decomposition algorithm is proposed to simplify data and improve the efficiency of the algorithm. The existence of injury is determined and the damage location is calculated by comparing with key features of healthy specimen. Experimental results prove the method is feasible and effective.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

The Azores Archipelago is a collection of volcanic islands near northwestern Portugal in the Atlantic Ocean. Because of the importance of accurate environmental monitoring for the advancement of research, transportation and tourism, a LoRaWan Sensor Network was developed to monitor levels of air pollution across these islands. This study presents an approach to the implementation of a blockchain network that is both lightweight and scalable, with the goal of preventing man-in-the-middle attacks on the design of sensor networks.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Background: Peyronie’s disease (PD) represents a challenging urological disease, due to not optimal post-operative surgical outcomes. We aim to evaluate if vacuum erection devices (VED) treatment before pe-nile curvature surgery is able to improve the post-operative surgical outcomes. Methods: All enrolled patients were assigned to the following groups: a) treatment group, VED treatment (3 times per week) starting 3 months before surgery and (3 times per week) one months after surgery and b) control group, VED treatment (3 times per week) one months after surgery. Follow-up urologic visits were scheduled at 3 and 6 months after surgery and the two groups were compared. Results: Thirty-eight patients have been enrolled (median age 67 years, 57-74, IQR), 20 in the treatment group and 18 in the control group. At the follow-up visits, the two groups are different in terms of IIEF-5 (26 vs 24; p=0.02), ‘yes’ to SEP2 and 3 (85% vs 55%; p<0.001, 85% vs 50%; p<0.001, respectively) and PDQ (-16 vs -11; p=0.03). Complete correction of penile curvature was achieved in 36 patients (94.7%). In the treatment group, no hourglass deformity has been reported, while in the control group 1 patient reported a mild hourglass deformity. In the treatment group, we obtained a longer total penile length (median +1.5 cm). The overall satisfaction rate was 98% in the treatment group and 96% in the control group. Conclusions: The VED treatment before penile curvature surgery in patients affected by PD is able to improve the post-operative surgery.

This comprehensive study focused on the standard taxi sign used in Ireland, its impact on drag production, fuel expenses, and CO2 emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately 832 per year and reduce national CO2 emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car.

Many buildings built before the energy performance regulations are in a situation of thermal discomfort and energy inefficiency. The creation of intelligent environments advances towards new opportunities, based on real-time monitoring and on the development of sensors and technologies. Furthermore, the standards for building automation and electronic systems enable interoperability and interconnection between control devices and systems. The application of soft computing has significantly improved the energy efficiency, however, requires prior assessment to design the automation functions. Temperature, humidity, air quality, occupancy and energy consumption are the most common measured parameters, but the relationship with other operational variables such as occupancy or some building states remains as a research challenge. This article presents a methodology to develop the automatization of an existing large public building. The methodology consists of three stages: 1. Assessment and diagnosis to set appropriate actions using EN ISO 52120-1. 2. EN 50090 for open communication networks, and EN ISO 52120-1 to assign the technical building management. 3. System control deploying of low-cost and low-consumption input and output devices. It has been proved that it is possible to effectively automate an obsolete building with a low cost, open source system that can be easily applied in other buildings.

This paper is a review of the current state of IoT-based technologies in the healthcare field for the elderly population. The increasing population of elderly people has led to a greater demand for healthcare services to meet their unique needs. IoT-based technologies have emerged as a promising solution to address this demand. The paper analyses the current trends, challenges, and future opportunities for research in this area. It highlights how IoT-based technologies can be utilized to improve healthcare for older adults, from remote monitoring and telemedicine to fall detection and medication management. The paper also acknowledges that there are still challenges to be addressed, such as data privacy and security, but the potential benefits for older adults outweigh the challenges. The paper also examines the impact of the industrial revolution on the aging population and the corresponding increase in demand for geriatric healthcare. In summary, this paper delves into the current status of IoT-based technologies in geriatric healthcare and its future prospects, with a focus on addressing the needs of the aging population and improving their quality of life.

In the last decades, the automatic recognition and interpretation of brain waves acquired by electroencephalographic (EEG) technologies have undergone remarkable growth, leading to a consequent rapid development of Brain Computer Interfaces (BCIs). EEG-based BCIs are non-invasive systems that allow communication between a human being and an external device interpreting brain activity directly. Thanks to the advances in neurotechnologies, and especially in the field of wearable devices, BCIs are now also employed outside medical and clinical applications. Within this context, this paper proposes a systematic review of EEG-based BCIs, focusing on one of the most promising paradigms based on Motor Imagery (MI) and limiting the analysis to applications that adopt wearable devices. This review aims to evaluate the maturity levels of these systems, both from the technological and computational points of view. The selection of papers has been performed following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA), leading to 84 publications considered in the last ten years (from 2012 to 2022). Besides technological and computational aspects, this review also aims at systematically list experimental paradigms and available datasets in order to identify benchmarks and guidelines for the development of new applications and computational models.

Objective: To evaluate the physical and chemical stability of the antibiotic temocillin at the recommended dose for severe infections and contained in infusion bags or elastomeric devices at different temperatures for its use in Outpatient Parenteral Antimicrobial Therapy (OPAT) programs.Method: Solutions of temocillin 12 g/L diluted in 0.9% sodium chloride were stored at 4ºC ± 2ºC, 25°C ± 2°C, 32°C ± 2°C and 37°C ± 2°C for 72 h both in polypropylene infusion bags and in polyisoprene elastomeric pumps. Physical and chemical stability were evaluated at 12, 24, 30 48 and 72 h after manufacturing. The solutions were considered stable if color, clearness and pH remained unchanged and if the percentage of intact drug was ≥90%. Results: There were no observed changes in color or clarity in any of the refrigerated (4°C) samples or in the samples incubated at 25ºC and 32ºC. At 37ºC, an increase in intensity of yellow color was observed at 30, 48 and 72 h in both infusion bags and elastomeric pumps samples. All samples remained within the pH range 6.84–6.06. At 4ºC, 25ºC and 32°C ± 2°C, temocillin attained the stability criteria of ≥90% of the original concentration for the whole experiment in both devices. At 37ºC, temocillin was stable for 24 h but its concentration dropped below 90% from that time point both in the infusion bags and in the elastomeric pumps.Conclusions: According to the data provided in this stability study, temocillin administrated by continuous infusion would be an appropriate candidate for the treatment of patients that can be discharge to complete therapy in an OPAT program.

Smart devices such as smartphones, smartwatches, etc. are promising platforms that are being used for automatic recognition of human activities. However, it is difficult to accurately monitor complex human activities due to inter-class pattern similarity, which occurs when different human activities exhibit similar signal patterns or characteristics. Current smartphone-based recognition systems depend on the traditional sensors such as accelerometer and gyroscope, which are inbuilt in these devices. Therefore, apart from using information from the traditional sensors, these systems lack contextual information to support automatic activity recognition. In this article, we explore environment contexts such as illumination(light conditions) and noise level to support sensory data obtained from the traditional sensors using a hybrid of Convolutional Neural Networks and Long Short Time Memory(CNN_LSTM) learning models. The models performed sensor fusion by augmenting the low-level sensor signals with rich contextual data to improve recognition and generalisation ability of the proposed solution. Two sets of experiments were performed to validate the proposed solution. The first set of experiments used inertial sensing data whilst the second set of extensive experiments combined inertial signals with contextual information from environment sensing data. Obtained results demonstrate that contextual information such as environment noise level and illumination using hybrid deep learning models achieved better recognition accuracy than the traditional activity recognition models without contextual information.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

(1) Background: The evaluation of ventricular assist devices requires the usage of biocompatible and chemically stable materials. The commonly used polyurethanes are characterized by versatile properties making them well suited for heart prostheses applications but simultaneously they show low stability in biological environment. (2) Methods: An innovative material - copolymer of poly(ethylene-terephthalate) and dimer linoleic acid - with controlled and reproducible physico-mechanical and biological properties was developed for medical applications. Biocompatibility (cytotoxicity, surface thrombogenicity, hemolysis and biodegradation) were evaluated. All results were compared to medical grade polyurethane currently used in the extracorporeal heart prostheses. (3) Results: No cytotoxicity was observed and no significant decrease of cells density as well as no cells growth reduction was noticed. Thrombogenicity analysis showed that the investigated copolymers have the thrombogenicity potential similar to medical grade polyurethane. No hemolysis was observed (the hemolytic index was under 2% according to ASTM 756-00 standard). These new materials revealed excellent chemical stability in simulated body fluid during 180 days ageing. (4) Conclusions: The biodegradation analysis showed no changes in chemical structure, molecular weight distribution, good thermal stability and no changes in surface morphology. Investigated copolymers revealed excellent biocompatibility and great potential as materials for blood contacting devices.

The mobile devices caused a constant struggle for the pursuit of data privacy. Nowadays, it appears that the number of mobile devices in the world is increasing. With this increase and technological evolution, thousands of data associated with everyone are generated and stored remotely. Thus, the topic of data privacy is highlighted in several areas. There is a need for control and management of data in circulation inherent to this theme. This article presents an approach of the interaction between the individual and the public environment, where this interaction will determine the access to information. This analysis was based on a data privacy management model in public environments created after reading and analyzing the current technologies. A mobile application based on location via Global Positioning System (GPS) was created to substantiate this model, which it considers the General Data Protection Regulation (GDPR) to control and manage access to the data of each individual.

In this paper, we present a finite element simulation of an adaptive piezoelectric fluid-membrane lens modeled in COMSOL Multiphysics. The simulation couples the piezoelectric effect with the fluid dynamics to model the interaction between piezoelectric forces and fluid forces. Also, the simulation is extended to model the thermal expansion of the fluid. Finally, we compare the simulation and experimental results of the adaptive lens refractive power at different actuation levels and temperatures.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

The work at hand focuses on an adaptive system aimed at improving the soundproof performance of car door seals at specific working regimes (cruise), without interfering with the conventional open-closure operations. The idea addresses the necessity of increasing the seal effectiveness, jeopardized by aerodynamic actions more and more important as the speed increase, generating a pressure difference between the internal and the external filed, in the direction of opening the door. To recover this effect, an expanding mechanism was integrated within the seal cavity, driven by an SMA actuator. The material was activated (heated) by Joule effect; its compactness, intrinsic of smart materials, contributed to arrive to a final system characterized by a high level of integrability (expanding cells). In this paper, the development process is described together with the verification activity, aimed at proving the functionality of the realized device. Starting from the industrial requirements, the most appropriate solution was identified highlighting the working principle and the main design parameters involved. Then, the envisaged system was designed and its executive digital mock up (CAD) was released. Prototyping and laboratory validation showed the reliability of the numerical models and the associated predictions. On this basis, the integration task within the actual reference car was faced. To demonstrate the isolation effect of the proposed system, an experimental campaign was finally organized in an anechoic room, achieving significant results on the concept value.

Structural DNA nanotechnology provides an excellent foundation for diverse nanoscale shapes that can be used in various bioapplications and materials research. From all existing DNA assembly techniques, DNA origami has proven to be the most robust one for creating custom nanoshapes. Since its invention in 2006, building from the bottom up using DNA has drastically advanced, and therefore, more and more complex DNA-based systems have become accessible. So far, vast majority of the demonstrated DNA origami frameworks are static by nature, but interestingly, there also exist dynamic DNA origami devices that are increasingly coming into view. In this review, we discuss DNA origami nanostructures that perform controlled translational or rotational movement triggered by predefined DNA strands, various molecular interactions and/or other external stimuli such as light, pH, temperature and electromagnetic fields. The rapid evolution of such dynamic DNA origami tools will undoubtedly have a significant impact on molecular scale precision measurements, targeted drug delivery and diagnostics, but they can also play a role in development of optical/plasmonic sensors, nanophotonic devices and nanorobotics for numerous different tasks.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

The study of localized surface plasmons (LSPs) in nanoscale structures is an essential step towards identifying optimal plasmonic modes that can facilitate robust optomechanical coupling and deepen our understanding of light-matter interactions at the nanoscale. This paper investigates numerically, using the finite element method, LSPs modes in a design comprising two coupled nano-ridges deposited on a gold layer, with an interposing polymer spacer layer. Such a structure, usually referred to as particles-on-mirror, shows exquisite optical properties at the nanoscale. We first examine the LSPs modes of a single nano-ridge through the analysis of its scattering cross-section in the visible and infrared range. To enhance the plasmonic response, a thin polymer layer is placed at the middle of the ridge, which introduces additional LSPs modes confined within the former. Then, we extend the analysis to the dimer configuration, which exhibits more complex and enhanced plasmonic behavior compared to a single nano-ridge. In particular, the dimer configuration yields LSPs resonances with a quality factor enhancement of approximately threefold relative to single nano-ridge. Furthermore, the presence of the polymer layer within the ridges significantly improves plasmon field localization and quality factor. These findings underscore the potential of nano-ridge-based structures in advancing optomechanical coupling and plasmon-phonon interaction studies, offering valuable insights for the development of high-performance acousto-plasmonic devices. In particular, the proposed device could help significantly improve the design of nano-acousto-optic modulators operating in the visible or in the near infrared, that require enhanced light-photon coupling rate.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

Protein–nanoparticle hybridization can ideally lead to novel biological entities characterized by emerging properties, which can sensibly differ from those of the parent components. Herein, the effect of ionic strength on the biological functions of recombinant, His-tagged spermine oxidase (i.e., SMOX) was studied for the first time. Moreover, SMOX was integrated to colloidal surface active maghemite nanoparticles (SAMNs) by direct self-assembly, leading to a biologically active nano-enzyme (i.e., SAMN@SMOX). The hybrid was subjected to an in-depth chemical-physical characterization highlighting that protein structure was perfectly preserved. The catalytic activity of the nanostructured hybrid (SAMN@SMOX) was assessed by extracting kinetics parameters using spermine as substrate and compared to the soluble enzyme as a function of ionic strength. Results revealed that the catalytic function was dominated by electrostatic interactions and that they were drastically modified upon hybridization with colloidal ɣ-Fe2O3. Noteworthy, the affinity of SMOX toward spermine was significantly higher for the nanohybrid at low salinity. The present study supports the vision of using protein–nanoparticle conjugation as a mean for modulating biological functions.

Significant amount of oil remains in the reservoir after primary and secondary operations and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study new nano polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85% and that of cassava nanoparticles (CSNPs) is 90.53%. Synthesized materials were characterized through particle size distribution (PSA), zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs as found from recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. More incremental recovery (33.46%) has achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This opens the inception for a new technology for polymer flooding that may replace the conventional method that depends on partially hydrolyzed polyacrylamide (HPAM).

We synthesized iron(II)-triazole spin crossover compounds of the type [Fe(atrz)3]X2 and incorporated and deposited them on electrospun polymer nanofibers. In view of possible applications, we chose iron(II)-triazole-complexes that are known to exhibit spin crossover close to ambient temperature. Therefore we used the complexes [Fe(atrz)3]Cl2 and [Fe(atrz)3](2ns)2 (2ns = 2Naphthalenesulfonate) and analyzed them with IR-, UV/Vis and Mossbauer spectroscopy and with a SQUID magnetometer. The synthesized complexes were then in one attempt deposited on fibers of polymethylmethacrylate (PMMA) and in another attempt incorporated into core-shell like PMMA fiber structures. This was done via two different electrospinning methods. Deposition was performed by uniaxial electrospinning and incorporation was performed by coaxial electrospinning. The obtained polymer-complex-composites were then further investitgated by the same methods as the pure complexes as well as by SEM pictures and EDX measurements. The analysis by UV/Vis spectroscopy, Mössbauer spectroscopy and temperature-depended magnetic measurements with the SQUID magnetometer showed that the spin crossover properties were maintained and were not changed after the electrospinning processes and that the complexes were not harmed during the procedure.

The physicalchemistry properties and crystal structure of were nano-ZrO₂+3mol.%Y₂O₃ determined. The kinetics of the formation of H₂ as a result of the decomposition of H₂O on the surface of nano-ZrO₂+3mol.%Y₂O₃ was studied. Effects of adsorption and desorption process on ZrO₂+3 mol.%Y₂O₃ nanoparticles were studied at different (T=400÷1000⁰C) temperature. The study of H₂ in thermal processes at nano-ZrO₂+3 mol.%Y₂O₃ system increased. Such an increase in H₂ generation in comparison with a pure H₂O as thermal processes had formedactive centers for H₂O decomposition on the surface of the catalyst at the expense of δ-electrons emitted on the surface of nano-ZrO₂+3 mol.%Y₂O₃. This showed that the dimensions of the studied nanoscale particles systems are comparable to the free running distance of energy carriers generated by of nano-ZrO₂+3 mol.%Y₂O₃ as a result of thermal processes. These results are promising for hydrogen generation by waer spliting in near future.