Electric road systems (ERS) are a group of technologies that allow powering adequately-equipped road transport vehicles with electricity from the road infrastructure while in motorway traffic. They can be categorised in three technology groups: overhead catenary, ground conductive and ground inductive, depending on the used mode of power transfer. The supplied energy is used for propulsion and for charging the vehicle batteries to be used once the vehicle leaves the electrified road section. Also, another energy source, e.g. diesel, natural gas or hydrogen, can be used while away from ERS. This research investigates the potential impacts of implementing the different ERS technologies on the Rotterdam-Antwerp motorway corridor that links the two largest ports in Europe. The aim is to identify which of the routes between the ports is best suited for implementation of ERS, whether there are substantial differences in economic performance of the different ERS technologies, see what ERS vehicle traffic volumes are required and potentially available for successful implementation, what investment is required to build the system and whether the ERS operator can be profitable, and could transport operators operate their trucks on ERS profitability in this corridor setting. The research shows that that the route between Rotterdam and Antwerp that runs on motorway E19 is the best to be electrified from an economic standpoint. Our calculations show that the traffic on Rotterdam-Antwerp corridor is sufficient for economically justifying ERS infrastructure rollout and operation. For transport operators, that happen to have specific client base, e.g. where they usually serve clients from one of the ports along the electrified route, the construction of ERS on the route can prove to be very lucrative if they adopt the technology early.

With an increasing adoption of Battery Electric Bus (BEB) fleets, developing a reliable charging schedule is vital to a successful migration from their fossil fuel counterparts. In this paper, a Simulated Annealing (SA) implementation is developed for a charge scheduling framework for a fixed-schedule fleet of BEBs that utilizes a proportional battery dynamics model, accounts for multiple charger types, allows partial charging, and further considers the total energy consumed by the schedule as well as peak power use. Two generation mechanisms are implemented for the SA algorithm denoted as the "quick" and "heuristic" implementations, respectively. The model validity is demonstrated by utilizing a set of routes sampled from the Utah Transit Authority (UTA) and comparing the results against two other models: the BPAP and the Qin-Modified. The results presented show that both SA techniques offer a means of generating operationally feasible schedules quickly while minimizing the cost of operation and considering battery health.

Electric vehicles (EVs) play a significant role in reducing carbon emissions. In the US, EVs are mostly owned by multi-vehicle households, and their usage is primarily studied in the context of vehicle miles traveled. This study takes a unique approach by analyzing EV usage through the lens of vehicle choice (between EVs and internal combustion engine vehicles) within multi-vehicle households. A two-step machine-learning framework (clustering and decision trees) is proposed. The framework determines the preferred trip category for EV use and captures the effects of household attributes, driver attributes, built-environment factors, and gas prices on EV use in multi-vehicle households. Results indicate that discretionary trips (accumulated local effect = 0.037) are mostly preferred for EV use. EV preference is more pronounced among households with fewer workers (<2) and lower income levels. These findings are valuable for policymakers and auto manufacturers in targeting specific market segments and promoting EV adoption.

Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

The electrical energy supply relies on the satisfactory operation of insulators. The ultrasound recorded from insulators in different conditions has a time series output, which can be used to classify faulty insulators. The random convolutional kernel transform (Rocket) algorithms use convolutional filters to extract various features from time series data. This paper proposes the combination of Rocket algorithms, machine learning classifiers, and empirical mode decomposition (EMD) methods, such as complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN), empirical wavelet transform (EWT), and variational mode decomposition (VMD). The results show that the EMD methods combined with MiniRocket, significantly improve the accuracy of logistic regression in insulator fault diagnosis. The proposed strategy achieves respectively an accuracy of 0.992 using CEEMDAN, 0.995 with EWT, and 0.980 with VMD. These results highlight the potential of incorporating EMD methods in insulator failure detection models to enhance the safety and dependability of power systems.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

Autonomous vehicles (AV)s will transform transport, but public opinion will play a key role in the decision how widely and quickly, they will be adopted. The purpose of the study presented here, was to investigate community’s views on the transition. As a method for primary data collection on public awareness, attitudes, and readiness to use autonomous cars, survey was conducted in Saudi Arabia. Following that, we have used statistical tools to analyse responses. Our findings indicate that the participants are mainly open to use new technology and had favourable attitude towards transition. Ordinal logistic regression model showed a wide variation in public opinion regarding the expected benefits that may accompany the transition, despite an average high score on this factor. Our findings reveal that awareness of AVs' benefits is more positively correlated to the age of participants. Perceived cost, on one side, and convenience, and safety, on the other side, have substantial impact on opinions. Investigation, presented here, shows how AVs are seen in Saudi Arabia. This can guide the development of AVs and deployment in that region.

Due to nonlinear components in the charging piles of electric vehicles, harmonics and non-stationary signals in the electric vehicle charging load brings voltage and current distortion, seriously affecting the accuracy of the power-related calculation in non-sinusoidal environments. This paper proposed a new approach to calculate the active power and root mean square values from decomposed components using the adaptive chirp mode decomposition (ACMD) method on voltage and current. The advantage of the ACMD-based method is that it correctly provides the power-related quantities of harmonics or non-stationary components for the electric vehicle charging load. The performance of the proposed method was verified using synthetic signals and simulation tests. The experimental results presented better estimations for each quantity defined in IEEE Standard 1459-2010, compared with the discrete wavelet transform approach.

This paper provides a comprehensive overview of recent advancements in autonomous electric vehicle (AEV) within the specified region. It elaborates on the progress and comparative analysis of diverse subsystems, including energy storage, cell balancing for battery systems, vehicle charger layouts, electric vehicle motor mechanisms, and braking systems. Furthermore, this paper showcases several prototype autonomous electric vehicles as conclusive study findings.

This study demonstrates the possibility of growing green walls in normal commercial building environments with lighting designed primarily for aesthetic reasons, rather than the promotion of plant growth. Lighting is a key resource required for the growth and maintenance of robust green walls within interior environments. The study evaluated the appearance and growth of green walls with electric lighting used primarily for aesthetic reasons. Three identical green walls with six different plants were illuminated using three different white LED light sources for a period of five months. Plant health was monitored and documented in terms of growth patterns. One hundred and six subjects appraised the appearance of the walls using questionnaires. Findings of this study indicate that it is indeed possible to grow and maintain green walls in normal commercial building environments with lighting designed for aesthetic reasons. Further, it was observed that the selection of the correct plant species for the green walls is important to ensure plant health.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

The article presents development of the more electric turbofan engine in distributed architecture with a design thrust in the range from 3 to 7.5 and from 7.5 to 30 kN for small and medium-sized unmanned aerial vehicles. The engine subsystems are considered as separate smart modules with a built-in control system, exchanging data via a digital channel with the central engine control and diagnostics unit. The key smart engine units are combined in the following subsystems: starter and turbine generators, oil pumps, actuator of guide vanes, fuel pumps, fuel metering unit, control and diagnostic unit. All pumps and guide vane actuator are electrically driven. Control and monitoring signals are transmitted via a digital bus. Functional and reliability analysis, technical configuration design of each subsystem are presented. Based on analysis of the architecture of distributed control system for gearbox-free more electric engine, different configurations of described subsystems are proposed.

We consider the problem of coordinating the charging of an entire fleet of electric vehicles (EV), using a model-free approach, i.e. purely data-driven reinforcement learning (RL). The objective of the RL-based control is to optimize charging actions, while fulfilling all EV charging constraints (e.g. timely completion of the charging). In particular, we focus on batch-mode learning and adopt fitted Q-iteration (FQI). A core component in FQI is approximating the Q-function using a regression technique, from which the policy is derived. Recently, a dueling neural networks architecture was proposed and shown to lead to better policy evaluation in the presence of many similar-valued actions, as applied in a computer game context. The main research contributions of the current paper are that (i)we develop a dueling neural networks approach for the setting of joint coordination of an entire EV fleet, and (ii)we evaluate its performance and compare it to an all-knowing benchmark and an FQI approach using EXTRA trees regression technique, a popular approach currently discussed in EV related works. We present a case study where RL agents are trained with an epsilon-greedy approach for different objectives, (a)cost minimization, and (b)maximization of self-consumption of local renewable energy sources. Our results indicate that RL agents achieve significant cost reductions (70--80%) compared to a business-as-usual scenario without smart charging. Comparing the dueling neural networks regression to EXTRA trees indicates that for our case study's EV fleet parameters and training scenario, the EXTRA trees-based agents achieve higher performance in terms of both lower costs (or higher self-consumption) and stronger robustness, i.e. less variation among trained agents. This suggests that adopting dueling neural networks in this EV setting is not particularly beneficial as opposed to the Atari game context from where this idea originated.

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

Plants Microbial Fuel Cells (PMFC) is a new technology that generates electricity in a renewable, clean and sustainable way. In spite of these advantages, it still faces limitations in power generation and current density, reaching lower production values than other renewable technologies. Different studies maintain that the high resistivity of the cathode is the main limitation in the generation of energy; therefore, non-metallic materials to obtain a better performance are replacing the metallic electrodes. The implementation of these materials applied to PMFC requires a complex interdisciplinary work. Through three experimental tests using metallic electrodes for the extraction of electrons, this research study shows that the treatment of the substrate with natural materials, the volume plant roots, and substrate temperature and humidity control have a significant influence in the increase of the electric potential and the generated current.

Smart cities and smart technologies have been incorporated into several axes to increase the comfort of life. The connected building's concept was introduced for this reason. However, it was utilized in power management for better organizing, greater buildings management, and monetary savings. Cars technologies and the number of vehicles are also involved; Nowadays, each house has at least one car. Technological evolution helped to make those cars intelligent and connected. In the latest versions, the majority of those cars were equipped with several sensors, several communication protocols and a principal electrical control unit (ECU), especially for the electric vehicle model. This type of architecture was an essential element in a smart city, thus, it helps to manage power and decide when a vehicle needs to be charged. Based on the smart city concept and using possible network communication between buildings and vehicles, EVs can share their own information related to the powerful experience on a specific path. This information can be gathered in a gigantic database and used for managing the power inside these vehicles. In this field, we propose in this paper a new approach for power management inside an electric vehicle based on bi-communication between vehicles and buildings. The proposed approach is founded on two essential parts; the first is related to vehicles’ classification and buildings’ recommendation according to different car positions. Two algorithms, related to the SVC and neural network was employed in this work for implementing the final process. Different possibilities and situations were discussed for this approach. The proposed method was tested and validated using Simulink/Matlab application. The state of charge of the used battery was compared at the end of this work, for two specified cases, for showing the contribution of this approach.

In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

The technologies influencing alternative ways of transportation are augmenting in recent years as the need for transportation is increasing rapidly due to urbanization and motorization. In this paper, a solar powered electric auto-rickshaw (SPEA) is designed and developed for Indian conditions. The developed vehicle is comprehensively analyzed techno-economically for its viability in the Indian market. The performance analysis of SPEA results in an optimal charging rate of 2 kWh per day with an average solar irradiance of 325 W/m2. The discharging characteristics are studied based on different loading conditions. The vehicle achieved a maximum speed of 21.69 km/h with battery discharge rate of 296W at 90kg load and also reached a maximum discharge rate of 540W at 390kg loading with a maximum speed of 12.11 km/h. The environmental analysis of SPEA displayed yearly CO2 emissions of 1,777 kg, 1,987 kg and 1,938 kg using Compressed Natural Gas, Liquefied Petroleum Gas and gasoline engines respectively can be mitigated using SPEA. The results of financial analysis of SPEA were welcoming as the investor gets 24.44% lesser payback duration compared to gasoline run vehicle. Socio-Economic analysis of SPEA discussed its significant advantages and showed 18.73% and 3.9% increase in yearly income over gasoline driven and battery driven vehicles.

In our recent works we reported that physical and chemical characteristics of serum can vary in relation to the psychic activity of an individual depending on whether it is oriented to stress or relaxation. We wandered if these observations could be accompanied by an appreciable modification of the Ph, electric conductivity and Delayed Luminescence of the same serum samples. Our preliminary data may suggest that the serum pH could significantly increase during a Relaxation Response intervention while electric conductivity seems to decrease. Moreover, Delayed Luminescense could vary in the same subject according to the Relaxation Response practice. According to our proof of concept study, we postulate the appearance of a coherent system within the blood samples analyzed after the Relaxation Response. Further researches and some technical development are needed to support our preliminary findings.

Maxwell equation for the electric field has been solved for any medium by suggesting the wavenumber and angular frequency be complex quantities. This accounts for the field decay by interaction with the medium.This expression for the time and special decay of the electric field in a medium is used to construct a new wave function sensitive to the medium physical properties. This new wave function, unlike the conventional one, differentiates between a beam of particles in a vacuum and that enters a medium which is an attenuated due to the scattering effect.Another expression for time decaying electric field was obtained using Newton’s laws for frictional medium. This expression shows that the electric field diminishes due to friction.Fortunately, this time decaying part of the electric field is typical to that derived from Maxwell’s equations. Finally, a new Schrodinger equation sensitive to the medium properties was derived. This equation, fortunately, describes some scattering processes for Protein scattering, scattering of x-rays, opto-acoustic phonons, and Raman scattering for some materials successfully .

In the Neighborhood Area Network (NAN), the Advanced Metering Infrastructure (AMI) enables a bidirectional connection between the Smart Meter (SM) and the Data Concentrator (DC). Sensors, such as smart meter node or Radio Frequency transceiver, play a crucial role in collecting and transmitting data from meters to central unit for advanced monitoring, management, and analysis of energy consumption. Wired and wireless communication technologies can be used to implement the AMI-NAN. This paper delves into a novel approach for optimizing the choice of communication medium, Radio Frequency (RF) or Power-Line Communication (PLC), between the SM and DC in the context of AMI-NAN. The authors methodically select the specific technologies, RF and NB-PLC (Narrow Band Power-Line Communication), and meticulously characterize their attributes. Then, a comparative analysis spanning rural, urban, and industrial settings is conducted to evaluate the proposed method. The overall reliability performance of the AMI-NAN system requires a Packet Error Rate (PER) lower than 10%. To this end, a comprehensive methodology is introduced to assess and enhance the reliability of NB-PLC and RF for AMI-NAN applications. Simulation results demonstrate that wireless communication is the optimal choice for the rural scenario, especially for Signal to Noise Ratio (SNR) lower than 25 dB. However, in urban environments characterized by higher SNR values and moderately dense networks, NB-PLC gains prominence. In denser networks, it outperforms wireless communication, exhibiting a remarkable 10 dB gain for a bit error rate (BER) of 10-3. Moreover, in industrial zones characterized by intricate network topologies and non-linear loads, the powerline channel emerges as the optimal choice for data transmission, affording a gain surpassing 20 dB.

Highly nonlinear characteristics of lithium-ion batteries (LIBs) are significantly influenced by the external and internal temperature of the LIB cell. Moreover, cell temperature beyond the manufacturer’s specified safe operating limit could lead to thermal runaway and even fire hazards and safety concerns to operating personnel. Therefore, accurate information of cell internal and surface temperature of LIB is highly crucial for effective thermal management and proper operation of a battery management system (BMS). Accurate temperature information is also essential to BMS for the accurate estimation of various important states of LIB such as state of charge, state of health and so on. High capacity LIB pack, used in electric vehicles and grid-tied stationary energy storage system essentially consists of thousands of individual LIB cells. Therefore, installing a physical sensor at each cell especially at the cell core is not practically feasible from the solution cost, space and weight point of view. A solution is to develop a suitable estimation strategy which led scholars to propose different temperature estimation schemes aiming to establish a balance among accuracy, adaptability, modelling complexity and computational cost. This article presented an exhaustive review of these estimation strategies covering recent developments, current issues, major challenges, and future research recommendations. The prime intention is to provide a detailed guideline to the researchers and industries towards developing a highly accurate, intelligent, adaptive, easy to implement and compute efficient online temperature estimation strategy applicable to health-conscious fast charging and smart onboard BMS.

Exploring the dynamic behavior of cellular metabolism requires a standard laboratory method that guarantees rapid sampling and extraction of the cellular content. We propose a versatile sampling technique applicable to cells with different cell wall and cell membrane properties. The technique is based on irreversible electroporation with simultaneous quenching and extraction by using a microfluidic device. By application of electric pulses in the millisecond range, permanent lethal pores are formed in the cell membrane of Escherichia coli and Saccharomyces cerevisiae, facilitating the release of the cellular contents; here demonstrated by the measurement of glucose-6-phosphate and the activity of the enzyme glucose-6-phosphate dehydrogenase. The successful application of this device was demonstrated by pulsed electric field treatment in a flow-through configuration of the microfluidic chip in combination with sampling, inactivation, and extraction of the intracellular content in a few seconds. Minimum electric field strengths of 10 kV/cm for E. coli and 7.5 kV/cm for yeast S. cerevisiae were required for successful cell lysis. The results are discussed in the context of applications in industrial biotechnology, where metabolomics analyses are important.

Revealing the underlying pathomechanisms of neurological and psychiatric disorders, searching for new biomarkers, and developing novel therapeutics all require translational research. In vivo and in vitro disease models have been instrumental in casting light on complex polygenic, multifactorial, and heterogeneous disease mechanisms. In the most recent years, advanced preclinical models have revealed the intriguing interaction of sex/gender and aging with the pathogenesis and clinical manifestations of psychiatric and neurological diseases. However, despite these advancements, there is still a great deal of work to be done to fully comprehend the underlying mechanisms of these diseases and to develop treatments that can significantly improve the lives of those who suffer from them. The current challenge in the field of neurological and psychiatric diseases is to develop disease-modifying, effective treatments for these complex and long-lasting debilitating conditions with a high burden of disease.The first edition of the research topic ‘Emerging Translational Research in Neurological and Psychiatric Diseases: From In Vitro to In Vivo Models’ reinforces translational research playing a critical role in bridging the gap between basic research and clinical applications. Also, it provides a platform for researchers to share their findings and advancements in translational research in this field. This new collection gathers 25 papers offering insights into the latest advancements in translational research and potential new avenues for treatments. These papers cover various topics, including the development of new preclinical models, the use of in vitro and in vivo methods, and the application of qualitative and quantitative research methods.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

Background and Objectives: In recent years, electric scooters have gained widespread popularity as an easy and affordable mode of transport in urban areas worldwide. Simultaneously, trauma centres have observed an increasing number of associated injuries to users. While injury patterns associated with other vehicles are now well-researched, electric scooter-related injuries are a new topic in the literature. Our study aims to investigate the disparities in injury patterns and other critical accident characteristics among bicycle, electric scooter, and scooter riders. Materials and Methods: In this one-year prospective observational study, we examined patients who sustained injuries while riding bicycles, electric scooters, or scooters between April 2021 and March 2022 at Hungary's largest trauma centre in Budapest. During this one-year period, we identified 1938 patients, 1378 cyclists, 370 electric scooters and 190 scooter users. We collected basic demographic information, recorded injury type and severity, time of day the injury occurred, and alcohol intoxication. Results: While 4.6% of cyclists and 5.8% of scooter riders had consumed alcohol, 26.8% of electric scooter riders were intoxicated at the time of their accident. 45.8% of electric scooter-related injuries occurred at night, compared to only 9.2% and 14.1% of bike and scooter-related injuries, respectively. Sober patients were more likely to suffer mild and severe limb injuries (Odds Ratio (OR): 3.85, P = .0001 and OR: 3.26, P = .0001), but less likely to experience mild and severe head injuries (OR: 0.1, P = .0001 and OR: 0.25, P = .0001) than intoxicated patients. Cyclists had significantly fewer cases of severe head trauma than those injured while using electric scooters (OR: 0.34, P = .0166). Conclusions: Severe craniofacial injuries are more common in intoxicated patients and in patients injured using electric scooters.

In this paper, we investigate the behaviour of a relativistic quantum oscillator under the effects of Lorentz symmetry violation determined by a tensor (KF)µναβ out of the Standard Model Extension. We analyze the quantum system under a Coulomb-type radial electric field and a uniform magnetic induced by Lorentz symmetry breaking effects under a Cornell-type potential, and obtain the bound states solution by solving the Klein-Gordon oscillator. We see a quantum effect due to the dependence of the angular frequency of the oscillator on the quantum numbers of the system, and the energy eigenvalues and the wave-function of the oscillator field get modified by the Lorentz symmetry breaking parameters as well as due to the presence of Cornell-type potential.

The potential of metallic lithium to become the anode material for next-generation batteries is hampered by significant challenges, chief among which is dendrite growth during battery charging. These dendritic structures not only impair battery performance but also pose safety risks. Among the non-destructive analytical techniques in battery research, Magnetic Resonance Imaging (MRI) stands out as a promising tool. However, the direct imaging of lithium by 7Li MRI is hindered by its low sensitivity and spatial resolution, making its use for of dendritic growth imaging very difficult. Instead, a recently introduced indirect imaging approach based on 1H MRI of the electrolyte was used in this study. This method was used for sequential 3D imaging to monitor the charging process of lithium metal symmetric cells in three different electrical circuits: single cell, four cells in parallel, four cells in series. The measured sequential images allowed measurement of dendrite growth in each cell using volumetric analysis. The growth results confirmed the theoretical expectation that growth across cells is uneven in a parallel circuit and even in a series circuit. The methods presented in this study can be applied also to many other dendrite-related issues in batteries.

The work aims to improve the battery performance in hybrid electric vehicles (HEVs) by reducing the vehicle speed. We develop a specific protocol for managing battery use and optimizing the energy consumption rate to achieve this goal. The protocol automatically controls the driving operation, avoiding incompatible driving patterns with energy-saving mode and performance improvement. The protocol is submitted to a simulation process to predict the energy rate lowering and battery performance enhancement. The proposed protocol applies to any hybrid electric vehicle type and route conditions since it uses vehicle mass, drag and rolling coefficients, and road slope as variable parameters to determine the minimum energy consumption rate. We run experimental tests to validate the simulation data and the proposed protocol. Furthermore, the protocol applies to variable starting vehicle speeds, from 10 to 50 km/h, corresponding to the current driving patterns, sport, normal, and eco, set up by car manufacturers. A reduction of 10% in vehicle speed in urban and peripheral routes achieves a minimum energy rate, enhancing battery management. Current vehicle speed shows a deviation from optimum management of 18% while applying the vehicle speed reduction limits the deviation to 0.2%. Experimental results show a good agreement with simulation data with 94% accuracy. We tested the protocol for urban and peripheral routes with maximum vehicle speed limits of 60 and 90 km/h.

Efficient processing of end-of-life lithium-ion batteries of electric vehicles is important and a pressing challenge for a circular economy. Regardless of whether the processing strategy is recycling, repurposing or remanufacturing, the first processing step would usually involve disassembly. As battery disassembly is a dangerous task, efforts have been made to robotise it. In this paper, a robotic disassembly platform using four industrial robots is proposed to automate the non-destructive disassembly of a plug-in hybrid electric vehicle battery pack into modules. The work was conducted as a case study to demonstrate the concept of autonomous disassembly of an electric vehicle battery pack. A two-step object localisation method based on visual information is used to overcome positional uncertainties from different sources and is validated by experiments. Also, the unscrewing system is highlighted, and its functions, such as handling untightened fasteners, loosening jammed screws, and changing the nutrunner adapters with square drives, are detailed. Furthermore, the time required for each operation is compared with that taken by human operators. Finally, the limitations of the platform are reported and future research directions are suggested.

In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.

Keywords: Аrtificial neural network, electric drive system, database, stability, training algorithm, technological mechanisms.

Distributed electric propulsion technology has great potential and advantage in the development of drones. In this paper, to study the slipstream effect of distributed propeller, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by genetic algorithm. The analysis results showed that lift of the wing will be larger when the propellers are higher than the wing. When the relative height between the propeller and the wing is zero, the drag is the lowest. The influence of disk diameter on the slipstream is that the larger the diameter is, the higher the lift force and the drag force are. The slipstream effect of the optimized propeller distribution improves the lift-drag ratio of the wing, by 108.5% in the initial lift-drag ratio.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

In this study, the external magnetic field emitted by a wireless power transfer (WPT) system and the internal electric field induced into human body models during recharging operations of a compact electric vehicle (EV) are evaluated. To this aim an ad-hoc formulation for the source modeling is coupled with a commercial software that performs numerical dosimetry. Specifically, two realistic anatomical models both in a driving position and in a standing posture are considered, and the chassis of the EV is modeled either as a currently employed aluminum alloys and as a futuristic carbon fiber composite panel. Aligned and misaligned coil configurations of the WPT system are considered as well. The analysis of the obtained results shows that the ICNIRP reference levels are exceeded in the driving position, especially for the carbon fiber chassis, whereas no exceedance is observed in terms of basic restrictions, at least for the considered scenarios.

The spread of charging infrastructure (CIS) for battery electric vehicles is crucial for coping with the increasing number of electric vehicles. Therefore, the selection of ideal (fast-) charging locations determines acceptance, utilization and, thus, the economic viability of a single site or the whole charging network. The methodology of the Integrated Model Approach STELLA[1] for site identification of CIS uses proven methods of traffic modeling such as the classic four-step traffic modeling in a new context to enable statements regarding the positioning of CIS. Based on different spatial analyzes and characterizations of urban quarters, traffic generated by individuals is calculated using the FGSV approach of 2010. Because only (electric) motorized individual traffic is of importance for CIS, the share of trips is calculated by differentiating the modal split between various transport groups. One approach is to concretize the modal split share of public transport based on analyzes of different criteria and data sets, e.g. the accessibility of stops. The model approach STELLA, which also combines various extensive data (e.g. transport networks and traffic volumes, settlement structures, vehicle characteristics, power supply data and user requirements), is currently developed for a planning area covering the entire territory of the Federal Republic of Germany. [1] STELLA is the acronym for the German term "STandortfindungsmodell für ELektrische LAdeinfrastruktur”.

Heavy Ion Beam Probing (HIBP) diagnostic is a powerful tool for electric field studies in hot dense plasma of modern day toroidal magnetic confinement devices. On the TUMAN-3M to-kamak, the HIBP have been used in regimes with improved plasma confinement to clear up the role of radial electric field in the transition to good confinement regimes. Recently, a moderni-zation of the TUMAN-3M HIBP diagnostics was performed aiming to reconfigure it for a work with a reversed plasma current direction and improvement of overall stability of the diagnostic. The results of first measurements of plasma potential in co-NBI scenario are reported and dis-cussed.

Bus operators around the world are facing the transformation of their fleets from fossil-fuelled to electric buses. Two technologies prevail: Depot charging and opportunity charging at terminal stops. Total cost of ownership (TCO) is an important metric for the decision between the two technologies, however, most TCO studies for electric bus systems rely on generalised route data and simplifying assumptions that may not reflect local conditions. In particular, the need to re-schedule vehicle operations to satisfy electric buses’ range and charging time constraints is commonly disregarded. We present a simulation tool based on discrete-event simulation to determine the vehicle, charging infrastructure, energy and staff demand required to electrify real-world bus networks. These results are then passed to a TCO model. A greedy scheduling algorithm is developed to plan vehicle schedules suitable for electric buses. Scheduling and simulation are coupled with a genetic algorithm to determine cost-optimised charging locations for opportunity charging. A case study is carried out in which we analyse the electrification of a metropolitan bus network consisting of 39 lines with 4748 passenger trips per day. The results generally favour opportunity charging over depot charging in terms of TCO, however, under some circumstances, the technologies are on par. This emphasises the need for detailed analysis of the local bus network in order to make an informed procurement decision.

TThe number of supermarkets offering a grocery delivery has been increasing during the last years. Many studies deduce CO₂ emission savings using this concept. Since the delivery of groceries also consumes energy and produces emissions, break-even points can be calculated, from where the delivery has environmental advantages compared to the customer pickup. In this paper, influences of differing vehicle use on break-even points for savings of energy and CO₂ emissions are analyzed for the case of Haidhausen Süd, a city district of Munich in Germany. Internal combustion engine and electric vehicles are investigated to depict current as well as future trends. After an introduction to the used methodology, the potential to save energy and CO₂ emissions related to the delivery of groceries in the chosen district of Munich is evaluated. Afterwards, influences on the break even points are presented and discussed. As the results show, a delivery of groceries leads to energy and carbon dioxide savings in a wide range of private vehicle use for grocery shopping trips. Nevertheless, if the complete customer vehicle fleet is electrified, the use of delivery vehicles with an internal combustion engine can cause an additional environmental impact at the current modal split for shopping trips in Germany.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The transport sector in Germany causes one-quarter of energy-related greenhouse gas emissions. One potential solution to reduce these emissions is the use of battery electric vehicles. Although a number of life cycle assessments have been conducted for these vehicles, the influence of a transport system wide transition has not been researched sufficiently. Therefore, we developed a method which combines life cycle assessment with an agent-based transport simulation and synthetic electric, diesel and gasoline powered vehicle models. We use the transport simulation to obtain the number of vehicles, their lifetime mileage and road-specific consumption. Subsequently we analyze the product systems’ vehicle production, use phase and End-of-Life. The results are scaled depending on the covered distance, the vehicle weight and the consumption for the whole life cycle. The results indicate that the sole transition of drive trains is insufficient to significantly lower the greenhouse gas emissions. However, sensitivity analyses demonstrate that there is a considerable potential to reduce greenhouse gas emissions with higher shares of renewable energies, a different vehicle distribution and a higher lifetime mileage. The method facilitates the assessment of the ecological impacts of the complete car based transportation in urban agglomerations and is able to analyze different transport sectors.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

Natural time is a new time domain introduced in 2001. The analysis of time series associated with a complex system in natural time may provide useful information and may reveal properties that are usually hidden when studying the system in conventional time. In this new time domain, an entropy has been defined and complexity measures based on this entropy as well as its value under time-reversal have been introduced and found applications in various complex systems. Here, we review these applications in the electric signals that precede rupture, e.g., earthquakes, in the analysis of electrocardiograms, as well as in global atmospheric phenomena like the El Nino/La Nina Southern Oscillation.

In a recent paper, we extended previous studies on solar-terrestrial relationships by investigating the origin of the March 2012 heatwave in northeast USA. In the present study we check the possible relationship of solar activity with the early March 2012 bad weather in northeast Thrace, Greece. To this end, we examined data from various remote sensing instrumentation monitoring the Sun (SDO satellite), the Interplanetary Space (ACE satellite), the Earth’s magnetosphere (Earth based measurements, NOAA-19 satellite), the top of the clouds (TERRA and AQUA satellites) and the near ground atmosphere. Our comparative data analysis suggests that: (i) the winter-like weather (rainfall, fast winds, decreased temperature) in Thrace started on 6 March 2012, on the same day as the heatwave starting in USA, (ii) during the March 2012 winter-like event in Thrace (6-15 March), the ACE satellite recorded enhanced fluxes of solar energetic particles (SEPs), while SOHO and PAMELA recorded solar protons at very high energies (> 500 MeV), (iii) Thrace experienced particularly intense cyclonic circulation, during periods of magnetic storms on 8 - 10 and 12-13 March, which occurred after the arrival at ACE of two interplanetary shock waves, on March 8 and March 11, respectively, (iv) at the beginning of the two above mentioned periods large atmospheric electric fields were recorded, with values ranging between ~-2000V/m - ~1800V/m on 8 March, (v) the winter-like 8-10 March 2012 weather occurred after the detection of the main SEP event related with a coronal mass ejection released in the interplanetary space as a result of intense solar flare activity observed by SDO on 7 March 2012, (vi) the 8-10 March weather was related with a deep drop of ~630C in the cloud top temperature measured by MODIS/TERRA, which favors strong precipitation. Finally, we analyzed data from the electric power network in Thrace (~410N) and we found, for the first time sudden voltage changes of ~3.5kV in the electric grid in Greece, during the decay phase of the March 2012 superstorm. We discuss the winter-like March 2012 event in Thrace in terms of solar cosmic ray influence on the low troposphere mediated by positive NAO. Finally, we infer that the novel finding of the geomagnetic effects on the electric power grid in Thrace may open a new window into space weather applications research.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

Electric propulsion systems have emerged as a disruptive technological approach towards achieving sustainable and climate-neutral aviation. To expand the operational envelope of such propulsion units in terms of altitude and velocity, an enclosing duct and counter-rotating rotors to enhance efficiency can be utilized. In this study, an iterative CFD-based design tool developed for these novel propulsion systems is utilized to design a reference engine. A substantial reduction in discrepancies between initial specifications, subsequent CFD simulations, and experimental investigations compared to conventional design tools relying on empirical formulations can be demonstrated using a classic rotor-stator configuration. This allows the CFD-based tool to be validated for designing scalable counter-rotating fan engines. Furthermore, to facilitate the transferability of research on such propulsion systems, a validated manufacturing process for composite blades is presented. This effort aims to make state-of-the-art technology accessible to smaller research projects, promoting the widespread adoption of electric propulsion technology in the aviation sector.

In this exploratory work, we have examined the impact of an external static electric field on the H2 storage capacity of clathrate hydrates. To this end, we have chosen the 512 clathrate hydrate and examined the encapsulation of 1 - 4 H2 molecules within it. Results suggest that with the help of moderate electric fields (±0.10 to ±0.31V/Å), the encapsulation of 1 H2 molecule within the 512 clathrate hydrate becomes thermodynamically more favorable. In the cases of 4H2@512 and 2H2@512, however, the concerned processes become thermodynamically more favorable only when the field is applied along a specific direction. No favorable outcome could be observed in the case of 3H2@512, irrespective of the direction of the applied field. It appears from the results obtained herein that it might be possible to design a suitable external electric field to facilitate the hydrogen storage capacity of clathrate hydrates at ambient conditions, at least in certain cases.

Background: Neuromuscular electrical stimulation (NMES) has beneficial effects on physical functions in Multiple Sclerosis (MS) patients. However, the neurophysiological mechanisms underlying these functional improvements are still unclear. This study aims at comparing acute responses in spinal excitability, as measured by soleus Hoffmann reflex (H-reflex), between MS patients and healthy individuals, following three experimental conditions involving the ankle planta flexor muscles: 1) passive NMES (pNMES); 2) NMES superimposed to isometric voluntary contraction (NMES+); and 3) isometric voluntary contraction (ISO). Methods: 20 MS patients (MSp) and 20 healthy individuals as control group (CG) took part in a single experimental session. During each condition, participants performed 15 repetitions of 6 seconds at 20% of maximal voluntary isometric contraction, with 6 seconds of recovery between repetitions. Before and after each condition, H-reflex amplitudes were recorded. Results: In MSp, H-reflex amplitude did not change following any experimental condition (ISO: p = 0.506; pNMES: p = 0.068; NMES+: p = 0.126). In CG, H-reflex amplitude significantly increased following NMES+ (p = 0.01), decreased after pNMES (p = 0.000) and was unaltered following ISO (p = 0.829). Conclusion: the different H-reflex responses between MS and CG might reflect a reduced ability of MS patients in modulating spinal excitability.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

Microgrid is one of the important ways to accommodate distributed PV generation. However, the optimal planning scheme of microgrids is closely related to solar resources, load characteristics, and the key components of microgrid systems. This paper uses HOMER software to conduct collaborative planning for grid-connected PV-storage microgrids with electric vehicles in multiple scenarios. Specifically, we construct a multi-scenario capacity optimization model for PV generation, energy storage, and converters, considering both the cleanliness and economic performance of microgrids. The performance is quantified using indices such as net present cost, levelized cost of electricity, and carbon dioxide emission under multiple scenarios. Finally, we conduct extensive case studies on a business park in Wuhan, China, to compare and discuss the planning performance under multiple scenarios, as well as sensitivity analysis with specific cases.

We calculate energies of shallow donors confined in a rolled-up quantum well in the presence of the electric field by solving numerically the Schrödinger equation in natural curvilinear coordinates. It is found that the curves of density of states (DOS) are very sensitive to the variation of the donor position, the geometry of the spiral and the applied electric field value. Novel results for dependencies of donor’s dipole moment and its polarizability on the electric field strength and its orientation, for different donor positions are presented. Also, we found that anisotropic Stark effect of the first order provides in this structure a dependency of the polarizability on the external electric field in a spike-like shape, giving rise to a sharp variation of the dipole moment.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

Nowadays brushless DC motors (BLDCMs) are becoming indispensable components as the electrification revolution in the mobility industry is happening. Electric kick scooters, so-called e-scooters, are among these micro-mobility vehicles which are powered by these motors. Due to the uncertain and nonlinear features, the controller performance developed for these motors degrades. For these reasons, a chattering-reduced cascaded Sliding Mode Control (SMC) scheme to effectively track reference motor speed in the outer loop by eliminating torque ripples in the inner loop current control was designed. Field-oriented Control (FOC) methodology was used to implement the SMC in the BLDCM. An exponential reaching law algorithm was proposed for sliding surfaces of the inner and outer loop controllers. The suitability and performance of electric scooter-hub motors were analyzed in terms of traction control. A cascaded speed and torque controller produced significantly favorable results representing minimized torque and current ripples, and operation over a wide speed range.

The well-known coupling between the magnetic and electric fields in electromagnetic radiation is revisited in light of the recent introduction of a microscopic theory for the Ørsted magnetic field induction. I argue that, if the Ørsted magnetic field induction does indeed have a microscopic origin rather than the continuum solution offered by the Maxwell-Ampere equation, the "electromagnetic wave"' propagating in vacuum will not have a magnetic component.

This paper is a thorough review of innovative architectures of electro-hydraulic servovalves that exploit actuation systems based on piezo-electric materials. The use of commercially available piezo-electric actuators, namely, piezo-stacks, amplified piezo-stacks, rectangular benders and ring benders, is very promising for the actuation of the main stages and of the pilot stages of servovalves, given the fast response and low weight of piezoelectric materials. The use of these actuators can also allow novel designs to be developed, thus helping manufacturers to overcome the typical drawbacks of commercial servovalves, such as the high complexity and the high internal leakage of the pilot stages of two stage servovalves, as well as the large size and weight of direct drive servovalves. Firstly, the piezoelectric actuators that can be used for driving servovalves are presented in the paper and their characteristics are thoroughly discussed. Then, the main novel architectures present in the literature are explained and compared with the commercial ones, and their performance parameters are discussed to draw conclusions on the prospect that some of these architectures can be used by manufacturers as future designs.

An embryonic version of membrane theory can be date back to the Bernstein's work reported more than a hundred years ago. Such an originally old work has evolved conceptually and mathematically up until today, and it plays a central role in current membrane theory. Goldman-Hodgkin-Katz equation (GHK eq.) is one of the math-based monumental works, which constitutes the present membrane theory. Goldman theoretically derived GHK eq., but its physiological meaning was provided by the two renowned scientists, Hodgkin and Katz. These two employed an assumption that the electric field (EF) across the plasma membrane is constant to validate the GHK eq. physiologically. Proposal of Hodgkin-Huxley model (HH model) is another math-based monumental works developed from the membrane theory and now forms a fundamental part of the current membrane theory. GHK eq. and HH model are quite fundamental central concepts in the current physiology. Despite the broad acceptance of GHK eq. at present time, its prerequisite that the EF within the plasma membrane is constant is hardly believable. Especially when the action potential is generated, it sounds totally nonsense. Furthermore, the existence of constant EF within the plasma membrane is conceptually almost in conflict with the HH model. The authors will discuss those problematic issues the membrane theory inherits.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

An indisputable fact about our planet is that its atmospheric temperature has risen dramatically during the past century. Combustion of fossil fuels and their subsequent greenhouse gas emissions are thought to be the main contributors to recent changes within the Earth’s ecosystem. The transportation sector and electricity generating power plants are each responsible for approximately one-third of these emissions. Shifting towards a cleaner and renewable resources to generate electricity is believed to omit a big portion of polluting substances. Improvements in vehicles’ fuel efficiency and the introduction of alternative fuels besides strategic plans to control travel demand are among the most promising approaches to alleviate emissions from the transportation sector. Recent technology advancements, however, drew much attention to the production and manufacturing of alternative fuel vehicles, electric vehicles in particular. Since these vehicles use electricity as part of or all their powertrain, assessing the amount of emissions they produce is closely tied to the cleanliness of the electricity source. In order for a valid comparison to be made between internal combustion and electric vehicles, hence, a life cycle assessment procedure needs to be followed from production stages to terminal life of vehicles. Involvement of numerous affecting factors during the lifetime of a vehicle on one hand, and the ambiguity in the exact source of electricity used to charge electric vehicles on the other hand bring about more complexities. The latter case is more commonly known as the marginal grid problem, which deals with how a combination of sources used to generate electricity can influence the life cycle emissions. There are also other concerns regarding the growth in fuel-efficient and electric vehicles. Transportation planners argue that new developments in the vehicle industry may attract more people to owning and driving cars. This phenomenon which is better known as a rebound effect not only will result in increased traffic congestion, but it can also outpace the environmental benefits from utilizing electric vehicles. Moreover, since fuel taxes comprise the majority of Highway Trust Funds, alternative ways to compensate for state and federal revenues should be devised. This paper is an attempt to review the existing literature to better elaborate on the role of the transportation sector in controlling climate change threats. More specifically, issues around the use of electric vehicles and how they can contribute to more environmentally friendly communities are discussed.

Abstract: The article proposes to consider the possibility of connecting the problems of engineering synthesis of frequency control systems for asynchronous electric drives with the basic provisions of the theory of identification of asynchronous electric motors based on the equations of a generalized AC electric machine.The article presents the results of experimental studies of load parrying processes in asynchronous electric drives with vector and scalar controls. These results indicate the absence of fundamental advantages as processes in a drive with vector control. This advantage should have manifested itself in a more efficient formation of the moment and fast transients. It is suggested that the reason for this is in too significant errors, assumptions and simplifications of the equations adopted in the derivation of vector control and which are its theoretical basis. A method is proposed for describing asynchronous electric motors by nonlinear transfer functions, which made it possible to formulate the principle of correction of electric drives and a method for assessing their efficiency.The article shows. that the correction based on the proposed nonlinear transfer functions of the induction motor is much more efficient than the traditional vector control, which was confirmed by detailed experiments and modeling. The results of the most important of which are given in the article. An assumption was made. that the advantage in efficiency is due to a more accurate identification of the dynamics of an asynchronous electric motor with a gear function instead of vector equations.

Nowadays, there are several electric vehicle (EV) on the market, due to the innovation of technology that promotes the new components such as battery, transmission, electric motors. This paper proposes a design approach for the configuration synthesis and simulation of the in-wheel-hub motor transmissions with the six-link mechanisms. The synthesis process shows 6 mechanisms with six members and eight joints, 15 new clutchless motor transmissions and 16 new clutched motor transmissions. A novel motor transmission in the feasibility of the synthesized configurations is selected as an example to analyze the working principle with operation modes and power flow paths. And, this design is modeled for the simulation process that generates the results of operation mode transition and energy regulation.

Electric Vehicles (EVs) are increasing the interdependence of transportation policies and the electricity market. EMMEV (Electricity Market Model with Electric Vehicles) is an experimental agent-based model that analyses how carbon reduction policy in transportation may increase number of Electric Vehicles and how does that would influence on the electricity price. Agents are ESCOs (Energy Service Providers) which can distribute fuels and their objective is to maximize their profit. In this paper, EMMEV is used to analyze the impacts of the LCFS (Low Carbon Fuel Standard), a performance-based policy instrument, on electricity prices and EV sales. The agents in EMMEV/regulated parties in LCFS should meet a certain CI (Carbon Intensity) target for their distributed fuel. In case, they cannot meet the target, they should buy credit to compensate for their shortfall and if they exceed, they can sell their excess. The results, considering the assumptions and limitations of the model, show that the banking strategy of the agents contributing in the LCFS might have negative impact on penetration of EVs, unless there is a regular Credit Clearance to trade credits. It is also shown that the electricity price as result of implementing the LCFS and increasing number of EVs has increased between 2–3 percent depending on banking strategy.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

Geomagnetic induced current (GIC) is a ground end manifestation associated with the space weather perturbations that should be greatly taken into account by the society. Although the GICs implication to the power system is not regular, it can cause large scale of system failure. In equatorial, the power system is considered safe since the most intense of geomagnetic storm happened in high latitude. However, the internal damage due to GICs which finally led to the South African power system failure has totally changed the normal perception. Therefore, a preliminary investigation on the GICs activity in equatorial region is performed to understand the space weather impact to the power system. Time derivative of the horizontal magnetic field component (dB/dt) is done to indicate the GICs activity value based on Faraday’s law. All the reported power failures are compiled to produce the threshold value of dB/dt, which possibly cause the harmful effect to the system. Then, dB/dt analysis is extended to show the pattern of GICs activity in function of magnetic latitude and local time. The results reveal that power network in equatorial region has possibly suffered by GIC. Plus, high number of intense GIC activity in this region occurred during dayside.

A very high parking occupancy can negatively influence the traffic performance of an area by causing very long cruising times. A very low parking occupancy, on the other hand, is inefficient from a space utilization perspective. Thus, this paper proposes a framework to compute the optimal parking occupancy rate over a given time horizon based on a macroscopic traffic and parking model. This rate is set high enough to ensure an efficient usage of the parking infrastructure. However, it should also guarantee a high likelihood of finding parking in order to eliminate the drivers’ time wasted in cruising for parking and the added congestion it causes. The model outputs are based on small data collection efforts and low computational costs, and they can be generated without complex simulation software using a simple numerical solver. Multiple vehicle types are included into our methodology allowing us to generate insights about the optimal parking occupancy with or without differentiated parking (i.e., parking for specific vehicles, such as fuel and electric vehicles). In times of a modal shift towards electric vehicles, cities can use our model to evaluate how much parking supply (with battery charging opportunities) they would like to dedicate to electric vehicles in order to achieve optimal traffic and parking results, and whether a differentiated or semi-differentiated parking policy is desirable. We illustrate our framework in a case study of a central area within the city of Zurich, Switzerland, showing the traffic and parking impacts (e.g., average searching time for parking, total revenue created by parking fees, optimal parking occupancy rate) for different proportions of fuel and electric vehicles in the parking demand and/or supply. Our results confirm that optimal occupancy rates are between and for most realistic scenarios. We then discuss how these rates might change depending on various demand and supply relationships, and according to different parking policies. We show that equal proportions between electric vehicles in the demand and their parking spaces in the supply lead to the best traffic performance in the area. We also provide the tools for cities to analyze their loss in performance if they do not react, e.g., to an increasing demand for electric vehicles over time. Moreover, we illustrate how some of these risks can be mitigated by having more flexible parking policies, e.g., allowing electric vehicles to use parking spaces for fuel vehicles.

We previously reported new superconductivity produced by an electrostatic field and a diffusion current in a semiconductor without refrigeration. In particular, the superconductivity was investigated theoretically and confirmed experimentally. Here, we determine that the derived superconducting quantum state can be reproduced in a capacitor. When circuits are formed with this new-type capacitor and diodes, a magnetic field is applied to the diodes’ depletion layer. The depletion layer is biased because of the conversion from the magnetic-field energy to electric-field energy, resulting in the diodes’ spontaneously emitting a current. Thus, the new-type capacitor is charged using no other energy source. This new phenomenon is described theoretically with assistance of initial experiments.

An effective battery management system (BMS) is indispensable for any lithium-ion battery (LIB) powered systems such as electric vehicles (EVs) and stationary grid-tied energy storage systems. Massive wire harness, scalability issue, physical failure of wiring, and high implementation cost and weight are some of the major issues in conventional wired-BMS. One of the promising solutions researchers have come up with is the wireless BMS (WBMS) architecture. Despite research and development on WBMS got momentum more than a decade ago, it is still in a preliminary stage. Significant further upgradation is still required towards developing an industry-ready WBMS, especially for high-power LIB packs. Therefore, an in-depth survey exclusively on WBMS architectures is presented in this article. The aim is to provide a summary of the existing developments as well as to present an informative guide to the research community for future development by highlighting the issues, emerging trends, and challenges. In-depth analysis of the existing WBMS topologies will not only help the researchers to understand the existing challenges and future research scopes clearly while at the same time enthuse them to focus their research inclination in the domain of WBMS.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

This paper presents a novel real time control strategy on four-wheel independent steering system for electric vehicle with stepper motors using neural networks combined with fuzzy logic. The control of the four wheels is based on a variation of Hopfield Neural Network (VHNN) method, in which the input is the error of each steering motor and the output is processed by a hyperbolic tangent function (HTF) feeding the fuzzy logic controller (FLC), which ultimately drives the stepper motor. The whole system is made up of the four aforementioned blocks where they work in sync and inseparable from each other with the common goal of driving all the steering stepper motors at the same time. Simulation results demonstrate that the proposed control method has strong robustness and practicability under different angles and speeds.

This proposal advocates using energy states as fundamental units for quantum computer programming. Each programming unit is conceptualized as an energy state, manifested as an essence-unit. The essence-unit, defined as the minimal form encapsulating complete uniqueness or specificity, serves as the cornerstone of this paradigm. This approach allows recording various forms of matter on quantum computers in essence-units representing their energy states. Recording energy states is achieved through the creation of four distinct coherent potentials facilitated by quantum dots or crystals. It is crucial to note that these energy states, embodied in essence-units, cannot be subdivided. The study examines the intricate relationship between similarity, fractals, and uniqueness in quantum dot operations, elucidating their profound implications for information transfer efficiency. Normalized entropy quantifies the charge localization in quantum dot impurities in systems exhibiting distortions. Utilizing N-level recording and entropy-fractal dimension equivalence enables this paper to elucidate the potential of quantum dots in reducing transmission time and modeling complex systems. The proposed methodology represents a significant departure from the current state of quantum computing, offering unprecedented potential for overcoming previously intractable challenges.

The link between the world of communication and the world of racing is provided by telemetry systems in electric racing cars. These systems send real-time data about the vehicle’s behavior and systems to enable informed decisions during the race. The aim of this research was to integrate telemetry into the battery bank of a racing electric vehicle to find the optimal values of current and voltage that optimize the charging process, thus improving the vehicle’s performance in competition using Response Surface Analysis. Particularly, the telemetry system consisted of an Arduino Mega, a digital wattmeter, and temperature sensors, all installed in the vehicle. Once the telemetry data was obtained, a response surface design was adapted with current, voltage, and temperature as factors, varying from low to high values, with the objective function being to minimize the battery’s charging time. Applying the response surface methodology and the steepest descent algorithm, it was found that all factors significantly affect the charging time, with the minimum charge time being 6961 seconds, obtained with a current of 2.4 amps and voltages of 50.5 volts and 43.6 volts.

China’s leading development of a complete battery value chain for Electric Vehicles (EV) is restructuring the global automotive sector. The competitive advantage of China's EV battery industry lies on its firms’ core competency and political economic geography. Based on first-hand empirical material and data obtained from years of fieldwork in an EV battery cluster in South China, this paper identifies what the Chinese EV battery industry’s core competency is and details how it is built up from below. The current core competency of Chinese battery firms is their mass manufacturing capability to supply lithium-ion batteries vehicle manufacturers (OEMs) with stable and consistent quality as well as competitive prices. This competency is acquired by firms through technological learning at workshop level while taking use of their experiences accumulated in mass production of batteries for consumer electronics sectors. Furthermore, the rapid learning and accumulation of knowledge on battery manufacturing at large scale is also facilitated by the industrial cluster environment where firms are embedded. Supported and promoted by local government policies, Chinese EV battery clusters are composed of firms from different segments of a complete battery value chain. The findings illuminate the likely strategic strengths, weaknesses, and futures of the Chinese EV battery industry in global competition.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

This paper focuses on the impact that urban traffic has on the environment. The study characterizes the global effect of GHG emissions, including the ecologic evaluation and the characterization, normalization, and evaluation factor. The work makes a detailed survey of the different modes of driving and their influence on engine performance as one of the principal causes of gas emissions during the combustion process. The article analyzes six types of vehicles equipped with different engine configurations: diesel and gasoline, GLP and GNC, hybrid electric, and plug-in hybrid electric. Simulation of the driving mode under various operational conditions for every type of engine results in energy consumption, thus, in GHG emissions, carbon dioxide and monoxide, nitrogen oxides, and Sulphur dioxide. The study concludes that a reduction in vehicle speed, thus in the engine revolutions, has positive effects on engine combustion and gasses emissions, which is reduced by 27.5%. The study also concludes that the limitation in driving mode, avoiding sharp and sudden acceleration, may reduce up to 45% of GHG emissions. The changes applied in the driving mode improve the air quality in the urban environment, reducing the content of GHG from 39% to 61%.

Glycerol has found its applications as a heat-transfer fluid in heat exchangers, and as a compo-nent of functional solutions in biosensor analysis. Flowing non-aqueous fluids are known to be able to induce electromagnetic fields due to triboelectric effect. These triboelectrically generated electromagnetic fields can affect biological macromolecules. Horseradish peroxidase (HRP) is widely employed as a convenient model object for studying how external electric, magnetic, and electromagnetic fields affect enzymes. Herein, we have studied whether the flow of glycerol in a ground-shielded cylindrical coil affects the HRP enzyme incubated at a 2 cm distance near the coil’s side. Atomic force microscopy (AFM) has been employed in order to study the effect of glycerol flow on HRP at the nanoscale. Increased aggregation of HRP on mica has been observed after the incubation of the enzyme near the coil. Moreover, the enzymatic activity of HRP has also been affected. The results reported can find their application in biotechnology, food technology and life sciences application, considering the development of triboelectric generators, en-zyme-based biosensors and bioreactors with surface-immobilized enzymes. Our data can also be of interest for scientists studying triboelectric phenomena.

Lithium-ion batteries serve as the primary sources of power for electric vehicles (EVs) and hybrid electric vehicles (HEVs). For vehicle applications, battery management systems (BMSs) are nec-essary to protect lithium-ion batteries from overheating and to ensure optimum vehicle perfor-mance. Our approach to developing a BMS was based on recent advances in the application of phase field models for lithium-ion batteries. In particular, our reduced-order model (ROM) uti-lized a dataset generated from the COMSOL® Multiphysics simulation of the Cahn–Hilliard equation for a single particle of a lithium iron phosphate (LiFePO4) cathode: an example of using a reduced-order model (ROM) based on a single-particle model (SPM). The main innovation of our ROM is that the SPM is fully coupled to a heat transfer model at the battery cell level. We utilized principal component analysis to identify a lower-order model that could reproduce the battery’s voltage and temperature response for ambient temperatures ranging from 253 to 298 K and for discharge rates ranging from 1 C to 20.5 C. The reduced-order dataset was then fitted to the ex-perimental data for an A123 Systems 26650 2.3 Ah cylindrical battery using deep neural network (DNN) regression.

A block-diagonal fuzzy neural network for short-term load forecasting is proposed. DBD-FELF consists of fuzzy rules with consequent parts that are neural networks with internal recurrence. These networks have a hidden layer which consists of pairs of neurons with feedback connections between them. The overall fuzzy model partitions the input space in partially overlapping fuzzy regions, where the recurrent neural networks of the respective rules operate. The partition of the input space and determination of the fuzzy rule base is performed by use of Fuzzy C-Means clustering algorithm and the RENNCOM constrained optimization method is applied for consequent parameter tuning. The electric load time-series of the Greek power system is examined, and hourly-based forecasting for the whole year is performed. The performance of DBD-FELF is tested via extensive experimental analysis and the results are promising, since an average percentage error of 1.18% is attained, along with an average yearly absolute error of 76.2 MW. Moreover, DBD-FELF is compared with Deep Learning, fuzzy and neurofuzzy rivals, such that its particular attributes are highlighted.

Ion-exchange membranes (IEMs) are widely used in desalination, waste water treatment, food, energy production and other applications. There is a strong demand for cost-effective IEMs characterized by high selective transport of ions of a certain sign of charge. In this paper, we simulate the experimental results of V. Sarapulova et al. (IJMS 2021) on the modification of an inexpensive anion-exchange membrane (CJMA-7, Hefei Chemjoy Polymer Materials Co. Ltd., China) with a perfluorosulfonated ionomer (PFSI). The modification was made in several stages including keeping the membrane at a low temperature, applying a PFSI solution on its surface, and subsequent drying it at an elevated temperature. We apply the known microheterogeneous model with some new amendments to simulate each stage of the membrane modification. It has been shown that the PFSI film formed on the membrane-substrate does not affect significantly its properties due to the small thickness of the film (4 m) and similar properties of the film and substrate. The main effect is caused by the fact that PFSI material “clogs” the macropores of the CJMA-7 membrane, thereby blocking the transport of coions through the membrane. In this case, the membrane microporous gel phase, which has a high selectivity to counterions, remains the primary pathway for both counterions and coions. Due to the above modification of the CJMA-7 membrane, the coion (Na+) transport number in the membrane equilibrated with 1 M NaCl solution decreased from 0.11 to 0.03. Thus, the modified membrane becomes comparable in its transport characteristics with more expensive IEMs available on the market.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

In this work, we investigate the behaviour of relativistic quantum oscillator under the effects of Lorentz symmetry violation determined by a tensor $(K_F)_{\mu\nu\alpha\beta}$ out of the Standard Model Extension. We analyze this relativistic system under an inverse radial electric field and a constant magnetic field induced by Lorentz symmetry violation. We see that the presence of Lorentz symmetry breaking terms modified the energy spectrum of the system, and a quantum effect arise due to the dependence of the linear charge density on the quantum numbers of the system

In this work, we investigate the behaviour of a relativistic scalar particle in the background of the Lorentz symmetry violation determined by a tensor (KF)µναβ out of the Standard Model Extension. A linear electric field and a uniform magnetic can be induced by the violation of the Lorentz symmetry breaking effects, and analyze the behaviour of the scalar particle. We see that the analytical solution to the KG-equation can be achieved, and a quantum effect characterized by the dependence of the magnetic field on the quantum numbers is observed

We investigate a scalar particle under Lorentz symmetry breaking effects determined by a tensor out of the Standard Model Extension (SME) in the presence of a Cornell-type potential by modifying the mass term M → M +S in the KG-equation. The field configuration is such that a Coulomb-type radial electric field and a constant magnetic field can be induced by Lorentz symmetry violation, and analyze the behaviour of a scalar particle. One can see that the bound states solution to the KG-equation under the consider effects can be achieved, and a quantum effect characterized by the dependence of charge density distribution parameter on the quantum numbers of the system is observed.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

The meshless Petrov-Galerkin (MLPG) method is developed to analyse 2-D problems for flexoelectricity and thermoelectricity. Both problems are multiphysical and scale dependent. The size-effect is considered by the strain- and electric field-gradients in the flexoelecricity and higher-grade heat flux in the thermoelectricity. The variational principle is applied to de-rive the governing equations considered constitutive equations. The order of derivatives in governing equations is higher than in equations obtained from classical theory. The coupled governing partial differential equations (PDE) are satisfied in a local weak-form on small fic-titious subdomains with a simple test function. Physical fields are approximated by the mov-ing least-squares (MLS) scheme. Applying the spatial approximations in local integral equa-tions a system of algebraic is obtained for the nodal unknowns.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

Liquid propellants are fast becoming attractive for pulsed plasma thrusters due to their high efficiency and low contamination issues. However, the complete plasma interaction and acceleration processes are still not very clear. Present paper develops a multi-layer numerical model for liquid propellant PPTs. The model proposes a possible acceleration mechanism for liquid fed pulsed plasma thrusters and accurately predicts the propellant utilization capabilities and estimations for the fraction of propellant gas that is completely ionized and accelerated to high exit velocities. Validation of the numerical model and the assumptions on which the model is based on is achieved by comparing the experimental results from two different liquid-fed thrusters developed at the University of Tokyo. Results show 50% of liquid propellant injected is completely ionized and accelerated to high exit velocities (> 50Km/s), whereas, neutral gas contribute to only 7% of the total specific impulse and accelerated to low exit velocity (< 4Km/s). The model shows an accuracy up-to 92%. Optimization methods are briefly discussed to ensure efficient propellant utilization and performance. The model acts as a tool to understand the background physics and to optimize the performance for liquid-fed PPTs.

This paper is a mini literature review about electromagnetic field’s effects on cells, tissues and new treatment modalities. We have reviewed a papers which have been published in high quality journals in the last 5 years as two authors. This review’s aim is to be a resource for experimental studies about electricity’s effects on cell biology and pathophysiology. As a result of this literature review, we found that especially extremely low electric frequency and intermediate frequency fields have very important pathophysiological effects. We have mentioned four important expressions on this subject; electroporation, electrofusion, electrochemotherapy, gene electrotransference. Two different new treatment approaches have been developed by use of these two important electrical waves. First is tumor treating fields and the other is pulsed electric fields. Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma multiforme and malign melanoma.Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma and melanoma.

Background: biophysical stimulation therapy, and in particular Pulsed Electromagnetic Fields (PEMFs) and capacitively coupled electric fields (CCEFs) has significantly increased in the last twenty years. For this, it is necessary to have clear information regarding the efficacy, the therapeutic indication and the expected objectives. Methods: we conducted a narrative review taking into consideration different types of studies with different areas of application. The objective was to take into consideration and analyze the different fields of use and the relevant information present in the literature. Results: There is unanimous opinion regarding the usefulness of applying biophysical therapy on the bone compartment both in terms of the tissue healing process and the symptoms associated with this situation. Differently, but no less importantly, in the joint compartment positive opinions were observed mainly on the inflammatory and catabolic process, however, at present,we did not report evidence regarding cartilaginous tissue regeneration. Conclusion: the effectiveness of PEMFs and CCEFs on the bone healing process in the Orthopedic and Traumatology fields is consolidated evidence in the literature. We have also found positive results on symptoms and patient compliance with rehabilitation therapies. Therefore, notable application can be envisaged in the fields of Prosthetic Surgery and Sports Medicine.

With firm commitment to energy labelling, it is not a question of if but only of when the European Union will introduce an energy label for electric cars. To support such policy efforts, we conducted a scoping analysis of energy consumption and efficiency trade-offs for 342 electric car models sold in Europe. The results suggest that certified and real-world energy consumption average 19 ± 4 kWh/100 km and 21 ± 4 kWh/100 km, translating into drive ranges of 440 ± 120 km and 380 ± 110 km, respectively. Energy consumption is correlated with vehicle mass, frontal area, and battery capacity, but less so with rated power and vehicle price. Each 100 kg of vehicle mass and 0.1 m2 of frontal area tend to increase energy consumption by 0.20 ± 0.06 kWh/100 km and 0.72 ± 0.05 kWh/100 km. Raising battery capacity by 10 kWh increases vehicle mass by 145 kg, energy consumption by 0.6 kWh/100 km, and drive range by 45 km. Efficient vehicles are available at any price but drive range has a cost. Our findings point to considerable efficiency trade-offs that could be tapped by a dedicated energy label. We propose several options for categorizing vehicles on an efficiency scale from A to G, with and without additional utility parameters. Our analysis provides rationale for energy labelling of electric cars in Europe and could inspire similar analyses for other vehicle categories such as e-scooters, lightweight three- and four-wheelers, e-busses, e-trucks, and electric non-road machinery.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

The purpose of this research is to present a thorough evaluation of the energy management system, which consists of hybrid energy storage systems, and its control algorithms, which may be used in electric vehicles. This paper outlines the characteristics of electric vehicles, research methods, analysis of the hybrid energy storage system architecture, converter topology, and energy management techniques. The strength and co-occurrence of keywords over the past ten years are shown in this study using a systematic research framework for performing a literature review and using keyword analysis techniques. The study reveals a pattern of recently and frequently used terms in works of literature. Consequently, their suitability, benefits, and drawbacks are assessed. In this study, the hybrid energy storage system and converter circuit architecture are evaluated and rated. Non-isolate DC-DC converter converter connected to SC is a suitable configuration for the hybrid converter because it is simple to build, reliable, and has minimal loss/weight/cost, which improves vehicle performance. In terms of the application of control strategies, it is shown that deterministic and fuzzy rule-based control techniques are successfully assessed using real-scale vehicle experiments and selected for manufacturing. On the other hand, real-time optimization-based energy management techniques have been effectively shown in lab-scale tests and may be used in a future real-scale vehicle.

Controlling the selectivity of detonation initiation reaction of explosive is a Holy Grail, and it seems to be an “idiot's daydream”, by strengthening external electric field, to reduce the explosive sensitivity. The effects of external electric fields on the initiation reactions in NH2NO2∙∙∙NH3, a model system of the nitroamine explosive with alkaline additive, were investigated at the MP2/6-311++G(2d,p) and CCSD/6-311++G(2d,p) level. The concerted effect in the intermolecular hydrogen exchange is characterized by an index of the imaginary vibrations. Due to the weakened concerted effects by the electric field along the −x-direction opposite to the “reaction axis”, the dominant reaction changes from the hydrogen exchange to 1,3-intramolecular hydrogen transference with the increase of the field strengths. Furthermore, the stronger the field strengths, the higher the barrier heights become, indicating the lower sensitivities. Therefore, by strengthening the field strength and adjusting the orientation between the field and “reaction axis”, not only can the reaction selectivity be controlled, but also the sensitivity can be reduced, in particular under a super-strong field. Thus, a traditional concept, which the explosive is dangerous under the super-strong external electric field, is broken theoretically. Compared to the neutral medium, the low sensitivity of the explosive with alkaline can be achieved under the stronger field. Employing atoms in molecules, reduced density gradient and surface electrostatic potentials, the origin of the reaction selectivity and sensitivity change is revealed. This work provides a new idea to the technical improvement for adding the external electric field into the explosive system.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

Recent advance in electric propulsion systems have demonstrated that these engines can be used for for long-duration interplanetary voyages. Constant specific impulse engine described as a thrust-limited engine is an example of this type of engine, processing the ability to operate at a constant level of impulse. The determination of minimum-fuel, planar heliocentric Earth-to-Mars low-thrust trajectories of spacecraft using a constant specific impulse is discussed considering the first-order necessary conditions derived from Lawden’s primer vector theory. The minimum-fuel low-thrust Earth-to-Mars optimization problem is then solved in two-dimensional, heliocentric frame using both indirect and direct methods. In the indirect method, two-point-boundary-value problems are derived to solve boundary value problems for ordinary differential equations. In the direct method, a general-purpose optimal control software called GPOPS-II is adopted to solve these optimal control problems. Numerical examples using two different optimization methods are presented to demonstrate the characteristics of minimum-fuel planar low-thrust trajectories with on-off-on thrust sequences at three chosen flight times and available maximum powers. The results are useful for broad trajectory search in the preliminary phase of mission designs.