We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Nobel metal nanohole arrays have been used extensively in chemical and biological systems due to their fascinating optical properties. Gold nanohole arrays (Au NHAs) were prepared as surface plasmon polaritons (SPP) generators for the surface-enhanced sum-frequency generation (SFG) detection of 4-Mercaptobenzonitrile (4-MBN). The angle-resolved reflectance spectra revealed that the Au NHAs have three angle-dependent SPP modes and two non-dispersive localized surface plasmon resonance (LSPR) modes under different structural orientation angles (sample surface orientation). An enhancement factor of ~30 was achieved when the SPP and LSPR modes of the Au NHAs were tuned to match the incident visible (VIS) and output SFG, respectively. This multi-mode matching strategy provided flexible controls and selective spectral windows for surface-enhanced measurements, and was especially useful in nonlinear spectroscopy where more than one light beam involved. The structural orientation- and power-dependent performance demonstrated the potential of plasmonic NHAs in SFG and other nonlinear sensing applications, and provided a promising surface molecular analysis development platform.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

A composite is a material formed from the combination of two or more constituent materials through a non-homogeneous mixture. This research aims to determine the effect of volume fraction and fiber orientation angle of the hybrid polyester-ulin wood powder (Eusideroxylon zwageri)-wire mesh composite on bending strength. The bending test was conducted using ASTM D-790 standard with a three-point bending test method. The composite was made using the hand lay-up method with various compositions of particles and polyester. The results showed that the composition with less ulin wood powder and finer mesh size with a 45° wire mesh angle orientation had the highest bending strength and high deformation capability. The addition of wire mesh did not significantly increase the bending strength but could reduce the effect of decreased deformation capability.

Diabetes mellitus is a chronic metabolic disease that affects over 10.5 percent of the global adult population. Biochemical and hematological parameters such as albumin (ALB) and red cell dis-tribution width (RDW) have been shown to be altered in diabetic patients. This study aims to cor-relate hematological and biochemical parameters with glycated hemoglobin (HbA1c). 777 adult individuals (372 women and 405 men, aged 19-85 years) were divided into three groups: 218 par-ticipants with HbA1c < 5.7% (group A: non diabetic), 226 with HbA1c ≥ 5.7% and < 6.5% (group B: prediabetic) and 333 with HbA1c ≥ 6.4% (group C: diabetic). Biochemical and hematological parameters were compared among the 3 groups. Analysis of variance was performed to deter-mine the correlations of the parameters among groups. ALB and sodium (Na) levels were signifi-cantly decreased in group C compared to groups A (ALB: 3.8 g/dL vs. 4.1 g/dL, p < 0.0001, Na: 138.4 mmol/L vs. 139.3 mmol/L, p < 0.001), and B (ALB: 3.8 g/dL vs. 4.0 g/dL, p < 0.0001, Na: 138.4 mmol/L vs. 139.6 mmol/L, p < 0.0001), while RDW-standard deviation (RDW-SD) and urea were increased in group C compared to group A ( RDW: 45.8 vs. 43.9 fL, p < 0.0001, Urea: 55.6 mg/dL vs. 38.5 mg/dL, p < 0.0001) . Mean platelet volume (MPV) was increased in group C com-pared to group A (9.3 fL vs. 9.1 fL, p < 0.05, respectively). Τhe increase of RDW-SD from group A towards B and C demonstrates the impact of hyperglycemia on red blood cells. RDW may be re-garded as a potential innovative biomarker for improving risk assessment of developing diabetes. These results highlight the potential role of these parameters as an indication for prediabetes that would alert for measurement of HbA1c.

Objectives- The aim of the study is to describe and validate an optical-coherence-tomography (OCT) based method to easily calculate specific volumes, overcoming the inability of current OCT software to automate a volumetric analysis for specific entities in retinal pathologies. Methods- After manual drawing with caliper of the specific entity on linear OCT scans and consequent automated measurement of its area, the following formula was used for volumetric calculation: Volume [mm³] = ∑area [mm²] x OCT-scan distance [mm]. Two independent observers calculated the retinal volume (RV) in eyes with normal foveal profile (NFP) and compared it with the automated measurements performed by the OCT software; as well as the volume of the foveal cavity (FC) or foveoschisis (FS) in eyes with lamellar macular hole (LMH). The measurements were re-acquired after six weeks. Intra- and inter-observer variability and variability with automated RV calculations were analysed. Results- The study included 62 eyes: 30 NFP and 32 LMH eyes. High degree of agreement was determined for inter-observer and intra-observer variability between the two observers or singular observer with Spectralis for RV in NFP eyes; as well as between the two observers for FC/FS volume in LMH eyes. Conclusions- We describe and validate, showing excellent inter- and intra-observer agreement, an easy, reliable and widely applicable method to calculate volumes which can be applied to any entity requiring a specific study in the context of retinal pathologies.

The knowledge of the precise anatomy and dimensions of the pulp chamber in the different teeth allows the odontologist to perform correct diagnosis, as well as treatment planning and moni-toring. The clinical practice has introduced cone-beam computed tomography (CB-CT) as a method to evaluate the morphology and dimensions of the pulp chamber. Nevertheless, micro-computed tomography (micro-CT) is regarded as the gold standard in approaching those topics. Here we have designed an algorithm that takes as input DICOM images from in vivo CB-CT of permanent molars to determine the accuracy CB-CT for evaluation of pulp chamber volume. The values were compared with those from in vivo CB-CT (rough and expert manipulated) and ex vivo micro-CT. The relative errors obtained with the volume calculated by the algorithm vs. the volume measured by micro-CT do not exceed 5.7%; also, no significant differences were found between algorithm volumes vs. manipulated CB-CT volumes while all volumes were different from those obtained with automatic CB-CT software. These data demonstrate that volume algorithm CB-CT based may be a reliable technique for evaluation of the pulp chamber volume in permanent molars and can be useful in the diagnosis of pulp diseases, as well as in the planning and monitoring of their treatments.

Pinus occidentalis, Swartz is the primary timber species in the Dominican Republic (DR). Despite its economic importance, studies conducted on this species are very scarce, making it difficult to estimate current inventory levels. This study aims to enhance the accuracy of estimating total bole volume of P. occidentalis in different ecological zones (EZs) within La Sierra, evaluating and comparing two established volume equations—combined variable and Schumacher-Hall—across nine modeling variants (MVs). An indicator variables analysis determined the necessity of distinct equations for two EZs. Fitting included both linear and nonlinear models. Our comprehensive statistical analysis included goodness-of-fit metrics to evaluate each model variant's performance rigorously. Modeling variant SH02 was most effective in the Dry Ecological Zone, showing superior performance in both fitting and validation phases. Similarly, SH03 emerged as the best fit for the Combined Intermediate and Humid Ecological Zones, achieving the lowest overall ranking sum among tested variants. The SH equation variants SH02 and SH03, provide reliable and precise volume estimations, allowing optimization of forestry management practices for P. occidentalis trees. The SH models outperformed the CV model variants' consistency in parameter estimation. This tailored approach employed ensures more accurate volume predictions, which is crucial for sustainable management and conservation efforts.

Tunnel-interchange connecting sections pose significant safety challenges on mountainous expressways due to their high incidence of accidents. Improving road safety necessitates a comprehensive understanding of driver behavior in such areas. This study explores the influences of road characteristics, signage information volume, and traffic conditions on drivers' car-following and lane-changing behavior in tunnel-interchange diverging areas. Utilizing driving data from 25 subjects of 72 simulated road models, driving performance is assessed using Friedman rank test and multivariate variance analysis. The results highlight the significant influence of both connection distance and signage information load on driving behavior. In tunnel-interchange scenarios, the reduction of velocity increased by 62.61%, and speed variability surged by 61.11%, indicating potential adverse effects on driving stability due to the environmental transitions. Decreased connection distances are associated with reduced lane-changing durations, larger steering angles, and increased failure rates. Furthermore, every two units increase in signage information leads to a 13.16% rise in maximum deceleration and a 5% increase in time headway. Notably, the signage information volume shows a significant interaction with connection distance (F=1.60, P=0.045) for most car-following indicators. Hence, the study recommends a maximum connection distance of 700 m and signage information not exceeding nine units for optimal safety and stability.

The signs and symptoms of Long COVID can be explained by a shortage of blood in the body and a resulting deficient blood flow through nearly all organs. This shortage arose during the acute phase of COVID19 by an increased breakdown of haematocytes, to which the liver responds by reducing the production of plasma, in order to prevent a too large decrease in haematocrit. In order to ensure the perfusion of organs that are directly necessary for survival, the body takes the emergency measure of diverting blood from other organs and tissues. The perfusion of the blood-producing organs is also affected by this distribution measure, which hinders the smooth recovery of the total blood volume. The body is stuck in this vicious circle: a shortage of circulating blood hinders the recovery of blood production. This explains the long duration of Long COVID. My proposed treatment of Long COVID focuses on the recovery of the correct volume of blood in the body of the right composition by the intravenous administration of donor blood products, starting with albumin concentrate. A trial treatment can be performed in any hospital without much additional preparations, and has a lower associated risk for the patient than analysing the total blood. A diagnosis ex juvantibus, by therapeutic response, is therefore preferable. I suspect that we will find a haematocrit value at the high extreme of the reference range, and an albumin value at the low extreme of the reference range in most Long COVID patients before the start of the treatment, because the liver can not keep up with the recovery of the red bone marrow.

In the paper, we develop some numerical schemes including finite difference scheme and finite volume scheme for the fractional Laplacian operator, and apply the resulted numerical schemes to solve some fractional diffusion equations. First, the fractional Laplacian operator can be characterized as the weak singular integral by a integral operator with zero boundary condition. Second, because of the solution of fractional diffusion equation is usually singular near the boundary, we apply finite difference scheme to discrete fractional Laplacian operator and fractional diffusion equation by fractional interpolation function. Moreover, it is find that the differential matrix of the above scheme is symmetric matrix, and strictly row-wise diagonally dominant in special fractional interpolation function. Third, we show finite volume scheme to discrete fractional diffusion equation by fractional interpolation function, and analyze the properties of differential matrix. Finally, the numerical experiments are given, and verify the correctness of theoretical results and the efficiency of the schemes.

Polarimetric Synthetic Aperture Radar (PolSAR) images with dual polarization modes have great potential to map FSV by excellent penetration capabilities and distinct microwave scattering processes. However, the response of these SAR data to FSV is still uncertain at non-growing season. To further interpret the response of forest FSV to these dual-polarization SAR images, three types of dual polarization SAR images (GF-3, Sentinel-1, and ALOS-2) were initially acquired in coniferous planted forest at non-growing season. Then, sensitivity between FSV and all alternative features extracted from each type of SAR images were analyzed to express the difference of bands and polarization modes in deciduous (Larch) and evergreen (Chinese pine) forests. Finally, mapped FSVs using single and combined dual polarization images were derived by optimal feature sets and four machine learning models, respectively. The combined effects were also analyzed to clarify the response of FSV to dual polarization SAR images with bands and polarization modes at non-growing season. The results demonstrated that the difference of backscattering energy from different sensors is significant in Chinese pine forests, and the difference is gradually reduced in Larch forests. it is also implied that polarization mode is more important than penetration capability in mapping forest FSV in deciduous forest at non-growing season. By comparing the accuracy of mapped FSV using single and combined images, combined images have more capability to improve the accuracy and reliability of mapped FSV. Meanwhile, it is also confirmed that compensation effect with bands and polarization modes not only have great potential to delay the saturation phenomenon, but also have capability to reduce errors caused by over-estimation.

Aim: This study aimed to investigate whether baseline 18F-FDG PET-derived semiquantitative parameters could predict disease-free survival in patients with grade III breast cancer of different molecular subtypes undergoing neoadjuvant chemotherapy (NAC). Materials and Methods: Patients were retrospectively retrieved from the databases of two Italian hospitals (University of Padua and University Hospital of Ferrara). Inclusion criteria were: 1) histologically proven diagnosis of grade III breast cancer; 2) history of NAC; 3) execution of a baseline 18F-FDG PET/CT scan before the start of NAC; 4) adequate follow-up time to compute the 3Y-DFS. For each 18F-FDG-PET/CT scan, the following parameters were calculated in the primary tumor (SUVmax, SUVmean, MTV, TLG) and whole-body (WB_SUVmax, WB_MTV, and WB_TLG). Receiver operating characteristic (ROC) analysis was used for each parameter to assess the prediction capability for 3Y-DFS. DFS differences between groups were assessed using Kaplan-Meier curves and compared by log-rank test. Results: Ninety-five grade III breast cancer patients with different molecular types were retrieved (luminal A: 5; luminal B: 34; luminal B-HER2: 22; HER2-enriched: 7; triple-negative: 27). In the whole group of patients, WB_SUVmax was the best predictor of recurrence (AUC: 0.66; best cut-off: WB_SUVmax>9.43; SS: 96%; SP: 38.1%; p<0.008). Patients with luminal A and Her-2-enriched breast cancer types were excluded from the molecular subgroup analysis due to the small study samples (5 and 7, respectively). In luminal B patients (n=34), WB_MTV (AUC: 0.75; best cut-off: WB_MTV>195.33; SS: 55.56%, SP: 100%; p=0.002) and WB_TLG (AUC: 0.73; best cut-off: WB_TLG>1066.21; SS: 55.56%, SP: 100%; p=0.05) were the best predictors of 3Y-DFS. Patients had a higher probability of DFS in case of a WB_MTV≤195.33 (3429±210 vs. 446±144 days; p<0.001) or WB_TLG≤ 1066.33 (937.35±19 vs. 496±131 days; p<0.001). In luminal B-HER2 patients (n=22), WB_SUVmax was the only predictor of 3Y-DFS (AUC: 0.857; best cut-off: WB_SUVmax>13.12; SS: 100%; SP: 71.43%; p<0.001); patients with WB_SUVmax≤13.12 had a significantly longer DFS (3857 days) than patients with a WB_SUVmax >13.12 (1693±430 days; p<0.004). No parameter resulted significant in the prediction of 3Y-DFS in patients with grade III triple-negative cancer. Conclusion: Volume-based parameters, extracted from baseline 18F-FDG PET, seem to be promising tools in the prediction of recurrence within 3 years in patients with grade III luminal B and luminal B- HER2 breast cancer undergoing NAC. Larger study samples are needed to confirm these preliminary findings.

Background: Natural environment inhalation topography provides useful information for toxicant exposure, risk assessment and cardiopulmonary performance. Commercially available Wearable Respiratory Monitors (WRM), which are currently used to measure a variety of physiological parameters such as heart rate and breathing frequency, can be leveraged to obtain inhalation topography, yet little work has been done. This paper assesses the feasibility of adapting these WRMs for measuring inhalation topography. Methods: Commercially available WRMs were compiled and assessed for the ability to report chest motion, data analysis software features, ambulatory observation capabilities, participant acceptability, purchasing constraints and affordability. Results: The following WRMs were found: LifeShirt, Equivital EQ02 LifeMonitor, Smartex WWS, Hexoskin Smart Garment, Zephyr BioHarness, Nox T3&amp;A1, BioRadio, SleepSense Inductance Band, and ezRIP &amp; zRIP Durabelt. None of the WRMs satisfied all six assessment criteria in a manner enabling them to be used for inhalation topography without modification and development. Conclusion: The results indicate that there are WRMs with core technologies and characteristics that can be built upon for ambulatory inhalation topography measurement in the NE.

The implementation of green roofs as sustainable urban drainage systems provides benefits for stormwater control and the environment and is always more encouraged. In this paper, the estimation of the probability of vegetation survival without irrigation has been proposed as a guide to choose the proper values for the design parameters; in particular the growing medium thickness has been related to the average return interval of the water content at the end of the dry period. Moreover the study represents an improvement of the analytical probabilistic approach since a chain of consecutive rainfall events has been considered, in order to take into account the possibility that the storage capacity is not completely available at the beginning of each event because of the pre-filling from more than one previous rainfall as typically happens for green roofs. Finally, developed equations have been validated by means of their application to two case studies, respectively in northern and southern Italy.

Tornadoes remain an active subject of observational and numerical research due to the damage and fatalities they cause worldwide as well as poor understanding of their behavior, such as what processes result in their genesis and what determines their longevity and morphology. A numerical model executed on a supercomputer run at high resolution can serve as a powerful tool for exploring the rapidly evolving tornado-scale features within a simulated storm, but saving large amounts data for meaningful analysis can result in unacceptably slow model performance, an unwieldy amount of saved data, and saved data spread across millions of files. In this paper, a system for efficiently saving and managing hundreds of terabytes of compressed model output is described in order to support a supercomputer simulation of a tornadic supercell thunderstorm. The challenges of managing a simulation spanning over a quarter trillion grid volumes across the Blue Waters supercomputer are also described. The simulated supercell produces a long-track EF5 tornado, and the near-tornado environment is described during tornadogenesis, where single upward-growing vortex undergoes several vortex mergers before transitioning into a multiple vortex tornado.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

In surgically treated individuals with surgical stomas, the return to sports activity is an indicator of quality of life that reflects their well-being. With the aim of synthesizing the available evidence regarding the return to physical activity and sports practice in individuals with surgical stomas, a scoping review was developed following the methodological approach of the Joanna Briggs Institute and the Preferred Reporting Items for Systematic reviews and Meta-Analyses for Scoping Reviews criteria. Searches were conducted in Medline (PubMed), Scopus, Web of Science, Cinahl, and Lilacs, as well as the meta-search engines TripDatabase and Epistemonikos, using the MeSH terms "exercise", "return to sports", and "surgical stomas"; including studies in Spanish, English, Portuguese, and German, without any limitation on the year of publication. A total of n = 15 studies with different designs were included (n = 2 qualitative; n = 1 cohort; n = 8 cross-sectional; n = 2 case reports; n = 1 case series; and n = 1 Randomized Clinical Trial), which showed variability in the quality of the designs. The studies revealed the complex relationship between physical activity and having surgical stomas, associated with the individuals' characteristics. There is a need to increase the number and rigor of research to understand the phenomenon of return to physical activity and sport, thus providing evidence-based clinical recommendations for sports practice in people with stomas.

Background: Tuberculosis (TB) continues to be a serious public health threat that affects the most vulnerable population. Patients who are LTFU after TB diagnosis still represent one of the biggest challenges to TB control. Method: In this prospective observational study, we aimed to identify and analyse the risk factors associated with LTFU among TB patients who started first-line TB treatment in the Sanatorium Hospital in Luanda. Result: A total of 113 patients with TB were included between August 2018 and September 2019. Seventy-six (67.3%) patients were cured, 27 (23.9%) were LTFU, 5 (4.4%) died, 4 (3.5%) were transferred and 1 (0.9%) presented a treatment failure. After excluding those dead, transferred or who failed to treatment, we observed that severe TB at the time of diagnosis (OR 9.24, 95% CI 2.18-39.04) and food insecurity were significantly associated with LTFU (OR 5.96, 95% CI 1.66-21.41). Conclusion: The findings of our study are of enormous value to understand the reasons for the LTFU of patients with TB and can guide polices and facilitate designing measures to allow better adherence, and therefore, greater treatment success

Breast cancer (BC) affects millions of women; it is the leading cause of death by neoplasia in wom-en worldwide, with at least 500 thousand deaths each year, 70% of which occur in developing countries. Elastography evaluates tissue stiffness, making this a promising non-invasive real-time technique. BI-RADS is recognized as a standard and helpful technique for establishing BC risk. This study aimed to determine, by strain elastography (SE), the fat-to-lesion index (F/L index), sen-sitivity, specificity, and optimal cut-off to diagnose BC. This prospective study included 216 wom-en who underwent SE, ultrasound, mammography, and breast biopsy; according to mammogra-phy, we recruited BI-RADS category 2 (n= 5), category 3 (n=29), category 4 (n= 94), category 5 (n= 71) and category 6 (n=17); after biopsy, 108 women were classified as negative, and 108 were pos-itive for BC. Three expert BC radiologists performed all imaging interpretations and biopsies. Our results show mean values of the F/L index for negative biopsies of 3.70±2.57 and positive biopsies of 18.10±17.01; we developed two models for the prediction of BC, a logistic regression model with an AUC of 0.893 and a neural network with an AUC of 0.902. The Youden index yielded a F/L index cut-off >5.76, with a sensitivity and specificity of 84.26%. Positive Spearman's Rho cor-relation coefficient was observed between the F/L index and BI-RADS, r=.073 (p< 0.001). ANOVA test showed a difference between F/L index vs. molecular subtypes (p=0.002). SE is helpful as a di-agnostic complement to mammography, or in cases where the latter is contraindicated, elas-tography has an adequate predictive capacity and is a fast and minimally invasive procedure.

It has been proposed that upregulation of the noradrenergic (NA) system through exposure to novelty might be one of the key components for building cognitive reserve and resilience to neurodegeneration. A personality trait that promotes greater interest in novel experiences is Openness to Experience (OE). Individuals who are high in OE exhibit strong curiosity towards novelty and are more likely to be exposed to novel stimuli throughout the lifespan.Performing voxel-based morphometry analyses, we examined whether OE in 135 healthy young adults was associated with Locus Coeruleus (LC) - the main core of the noradrenergic system. We also investigated whether LC mediates the relationship between OE and a key measure of reserve, I.Q. In comparison with other neuromodulators’ seeds (Dorsal and Median Raphe [DR-MR] -5-HT, Ventral Tegmental Area [VTA] -DA- and Nucleus Basalis of Meynert [NBM] -Ach-), results show that greater LC integrity was related to greater OE and IQ. Additionally, mediation analyses revealed that only LC mediated the relationship between OE and IQ. Furthermore, a Bayesian multiple regression was conducted to model the contribution of both isolated and combined neuromodulator seeds to OE trait express. This approach found that the LC + VTA could account for more variance in OE expression compared to the LC alone. Other weaker but significant associations were observed between DR and OE, between LC + NBM and Conscientiousness and between DR + NBM and Extraversion. These results are together suggestive that OE is primarily underpinned by monoaminergic functioning, and that the LC-NA system plays a central role mediating the interdependence between OE expression and cognition (IQ level). While offering further understanding of the neurobiology of human personality, these findings indicate a pivotal role of LC-NA system integrity in novelty seeking in daily life. This provides a psychobiological account for how OE expression may be beneficial for maintaining the noradrenergic system to facilitate cognitive reserve and resilience to neurodegenerative conditions.

This paper compares the performance of three text-to-speech (TTS) models released from June 2021 to January 2022 in order to establish a baseline for Brazilian Portuguese. Those models were trained using dataset for Brazilian Portuguese. The experimental setup considers tts-portuguese dataset to fine-tune the following TTS models: VITS end-to-end model; glowtts and gradtts acoustic models both using hifi-gan vocoder. Performance metrics are arranged into objective and subjective metrics. As subjective metrics, the naturalness and intelligibility are measured based on the mean opinion score (MOS). Results shows that gradtts+hifigan model achieved naturalness of 4.07 MOS, close to performance of current commercial models.

Background: Vaccinating children against COVID-19 is an essential public health strategy in order to reach herd immunity and prevent illness among children and adults. Parents are facing tremendous stress in relation to the COVID-19 pandemic and the effectiveness of the COVID-19 vaccination program for children. In this study, we aimed to investigate parents’ willingness to vaccinate their children against COVID-19 in North Kivu province (DRC). Methods: A cross-sectional survey between December 01, 2021 to January 20, 2022 in 6 health zones (Goma, Karisimbi, Butembo, Beni, Kamango and Katwa) was conducted in the province of North Kivu. In each health zone, we selected 5 clusters (Health area) using the method of probabilistic selection proportional to population size. In total, 522 parents participated in our study. Results: Overall, 32.8% of parents intended to vaccinate their children. In the multivariate analysis, younger age of parents (aOR : 2.40, CI : [1.50-3.83]), higher level of fear that “a member of my family” could contract COVID-19 (aOR : 2.35, CI : [1.38-4.02]), higher level of perceived vulnerability to COVID-19 within the family (aOR : 1.70, CI : [1.005-2.2881]), higher level of perceived susceptibility to COVID-19 within the family (aOR : 3.07, CI : [1.80-5.23]), and history of vaccination against COVID-19 among parents (aOR : 16.47, CI : [8.39-32.33]), were significantly associated with the intention to have their children or adolescents vaccinated. Conclusion: Willingness of parents to vaccinate their children against the COVID-19 vaccination was low in North Kivu. There is undeniably in this region a need to reinsure the populations about vaccine safety for both children and adults. Public health authorities should also address widespread misinformation about vaccines in a timely manner.

With the COVID-19 pandemic continuing and the resulting economic burden increasingly apparent, the Indonesian government began to prepare a "new normal" phase and make peace with COVID-19. From this new decision arises the question of the readiness of businesses and the industrial sector to resume operations amid COVID-19. This article aims to provide concise and precise information about the preparations that can be made by businesses to operate safely amid COVID-19 based on existing scientific studies and literatures. From the literature visits it can be concluded that transmission and danger of a COVID-19 pandemic can be prevented through: creation of infectious disease prevention and response plan, implementing basic infection prevention measures, policies and procedures for proper identification and isolation of sick people, applying flexibilities in policies, and protections in the workplace.

Here we review and describe a set of research priorities to meet present and future challenges posed to farmed animal production that build on progress, successes and resources from the Functional Annotation of ANimal Genomes (FAANG) project.

South America has become the new epicenter of the coronavirus, especially in Brazil where the disease continues to spread exponentially across the country. This text aims to analyze the psychosocial factors of Covid-19 on back to school strategies in Brazil from a bioecological perspective. At the microsystem level, the population is experiencing different levels of stress and fear; at the mesosystem level, changes in routines, separation from family and friends, and closure of schools; and at the macrosystem level, national guidelines to control the pandemic, institutional standards on a national and international scale. Therefore, the main focus for the success of school return must be in the prevention of contagion and with physical and psychological health, and should not only consider the demands of curricula, financial or administrative management. For this reason, it is paramount that greater female representativeness is increased in decision-making levels of the meso and macrosystem, regarding the resumption of school and academic activities in the pandemic period, since the number of female leaders in decision-making, is still insufficient.

The COVID-19 pandemic has presented the world with increased challenges. The response to this pandemic has led to a sudden disruption of routine medical and elective surgical care. Most hospitals across the globe have had to change the way outpatient clinics are carried out and postpone non-urgent elective surgical procedures. NHS England ceased all elective general surgeries to train and re-deploy their staff to support the increased pressures from COVID-19 in an intensive care setting. However, with a decline of reported cases and deaths, the return to undertaking non-urgent elective services is imminent. In May 2020, Radha and Afzal published the first evidence-based guidelines for the resumption of elective orthopaedic services titled “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic”. The pathway presented is adapted from the “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic” and could potentially be used as a model for other surgical specialities. We present a three-phased return back to urological services. Safe resumption of elective care is possible but needs to be carefully planned.

Most large fibers in central nervous system of vertebrates are decussated. The cause or the evolutionary force of this phenomenon is not convincingly described. Here we show a pattern for this nervous system property that simultaneously is found to a more basic rule in evolution.The idea here is the "function to anatomy" theorem. We claim that functions of physical, biochemical, enzymatic, etc., in lower scale of living organisms "emerge" to anatomy in larger scales. And reversely, the anatomy we see in multicelular organisms are/were functions in microscopic scales.We propose descriptions, predictions, and a probable road map to what this can implicate in biological and medical issues.

In 2014, the outbreak of adenoviral pneumonia occurred in Korean military training center. However, there is limited data on characteristics of fever and its response to antipyretics therapy in immunocompetent adults with adenoviral positive community-acquired pneumonia (CAP). Medical records of patients who were admitted to Armed Forces Chuncheon Hospital for treatment of CAP between January 2014 and December 2016 were retrospectively analyzed. We evaluated demographics, clinico-laboratory findings and radiologic findings at admission were compared between adenovirus positive (Adv) group and adenovirus negative (non-Adv) group. Out of 251 military personnel with CAP during the study periods, 67 were classified into Adv group while 184 were Non-Adv group. Patients with Adv group had a longer duration of fever after admission and symptom onset. Adv group patients had a higher mean temperature at admission and more observed over 40 and 39 to 40℃. Adv group patients had more commonly observed no response to antipyretic treatment and adverse events after antipyretics use. Length of hospital stay had no significant difference between two groups and no patient died in both groups. In our study, Adv positive CAP in patients with immunocompetent military personnel had distinct characteristics of fever and response to antipyretic treatment.

An understanding of the cultural conditions that determine the factors affecting nurses’ intention to leave is important for countries suffering from nurse shortage. Aim: to examine factors influencing intention to leave among female hospital nurses in a large Japanese sample, classified into four generations by age considering economic conditions. Methods: a cross-sectional survey with convenience sampling was conducted. Anonymous self-administered questionnaires were distributed to all nurses in 30 hospitals. To assess intention to leave, basic attributes, life conditions, work characteristics, and factors of psychosocial work environment were addressed. After classifying data into four generations based on age cohorts, we conducted multivariate logistic regression analysis using the completed data (N = 5,074, mean age = 36.24). Results: regardless of generational characteristics influenced by economic conditions, effort and monetary reward were generation-common factors. Over-commitment, social support, and the presence of a role model were generation-common factors in three generations. While having children increased intention to leave in the generation born 1965–1979, having family members in need of caregiving other than children decreased the risk in the generation born in the 1980s. Conclusion: generational countermeasures considering factors of psychosocial work environment and life conditions are needed to avert female nurse turnover.

Microaggressions are subtle verbal and non-verbal slights based on group membership, and they are ubiquitous in the lives of racial minorities, women, and LGBTQ individuals (Sue, 2010). The goal of the current paper is to introduce a role-playing based exercise on effective responses to microaggressions. The workshop draws on the prejudice responding workshops of Plous (2000) and Lawson, et al. (2010) but integrates research-based strategies. The activity was tested in two groups of undergraduate students, and the findings suggested that both groups felt more prepared to deal with microaggressions after participating.

Monochromatic documents claim for much less computer bandwidth for network transmission and storage space than their color or even grayscale equivalent. The binarization of historical documents is far more complex than recent ones as paper aging, color, texture, translucidity, stains, back-to-front interference, kind and color of ink used in handwritting, printing process, digitalization process, etc. are some of the factors that affect binarization. This article presents a new binarization algorithm for historical documents. The new global filter proposed is performed in four steps: filtering the image using a bilateral filter, splitting image into the RGB components, decision-making for each RGB channel based on an adaptive binarization method inspired by Otsu's method with a choice of the threshold level, and classification of the binarized images to decide which of the RGB components best preserved the document information in the foreground. The quantitative and qualitative assessment made with 21 binarization algorithms in three sets of “real world” documents showed very good results.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

A fundamental aspect in the evolution of Time-to-Digital Converters (TDCs) implemented within Field-Programmable Gate Arrays (FPGAs), given the increasing demand for detection channels, is the optimization of resource utilization. This study reviews the principal methodologies employed for implementing low-resource TDCs in FPGAs. It outlines the foundational architectures and interpolation techniques utilized to bolster TDC performances without unduly burdening resource consumption. Low-resource Tapped Delay Line, Vernier Ring Oscillator, and Multi-Phase Shift Counter TDCs, including the use of SerDes, are reviewed. Additionally, novel low-resource architectures are scrutinized, including Counter Gray Oscillator TDCs and interpolation expansions using Voltage-Temperature-Consumption stable IODELAYS. Furthermore, the advantages and limitations of each approach are critically assessed, with particular emphasis on resolution, precision, non-linearities, and, especially, resource utilization. A comprehensive summary table encapsulating existing works on low-resource TDCs is provided, offering a comprehensive overview of the advancements in the field.

Apraxia of speech is a persistent speech motor disorder that affects speech intelligibility. Studies on speech motor disorders with transcranial Direct Current Stimulation (tDCS) have been mostly directed to post-stroke aphasia. Only a few tDCS studies have focused on apraxia of speech or childhood apraxia of speech (CAS), and no study has investigated individuals with CAS and people with trisomy 21 (T21, Down Syndrome). This study examined the effects of tDCS combined with a motor learning task in developmental apraxia of speech co-existing with T21 (ReBEC RBR-5435x9). The accuracy of speech sound production of nonsense words (NSWs) during Rapid Syllable Transition Training (ReST) under 10 sessions of anodal tDCS (1.5 mA, 25 cm) over the Broca’s area with cathode over the contralateral region was compared to 10 sessions of sham-tDCS and 4 control sessions in a 20-year-old male individual with T21 presenting moderate-severe childhood apraxia of speech (CAS). The accuracy for NSWs production progressively improved (gain 40%) under tDCS only (sham-tDCS and control sessions showed <20% gain). A decrease in speech severity from moderate-severe to mild-moderate indicated transfer effects in speech production. The speech accuracy under tDCS was correlated with Wernicke’s area activation (P3 current source density), which in turn, was correlated with the activation of the left supramarginal gyrus and the Sylvian Parietal Temporal Junction. Repetitive bihemispheric tDCS paired with ReST may have facilitated the speech sound acquisition in a young adult with T21 and CAS, possibly by recruiting brain regions required for the phonological working memory.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

The environmental vulnerability diagnosis of a river basin depends on a holistic analysis of its environmental aspects and degradation factors. Based on this diagnosis, the definition of priority areas where interventions for environmental recovery should be carried out is fundamental, since financial and natural resources are limited. In this study, we developed a methodology to assess these fragilities using an Environmental Vulnerability Index (EVI) that combines physical and environmental indicators related to the natural sensitivity of ecosystems and their exposure to anthropogenic factors. The EVI developed was applied to the headwater’s region of the São Francisco River basin, Brazil. The proposed index was based on the AHP multi-criteria analysis and was adapted to include four variables representative of the study area: Land Use Adequacy, Burned Area, Erosion Susceptibility and Quantitative Water Balance. The EVI analysis highlighted that the presence of easily erodible soils, associated with sloping areas and land uses above their capacity, generate the most vulnerable areas in the headwaters of the São Francisco River basin. The results of this study indicate where resources should be applied for environmental preservation in the basin under study, directing the allocation of efforts to areas with lower resilience in maintaining ecosystem services.

Prunus armeniaca L. is the native species of cultivated apricot, which is important information for studying the origin, succession pattern, pest control, sustainable development of biodiversity of economic tree species of the genus Apricot, etc. However, with global climate change and increasingly intense human activities, the survival environment of Prunus armeniaca L. is under serious stress, and exploring the potential survival space of Prunus armeniaca L. is an important way to protect the health and development of Prunus armeniaca L.. Exploring the potential living space of Prunus armeniaca L. is an important way to protect the healthy development of Prunus armeniaca L. The Yili River Valley is a typical distribution area of Prunus armeniaca L. . Exploring the potential distribution suitable area of Prunus armeniaca L. in the Yili River Valley and analyzing its future change trend can provide scientific guidance for the protection, development, and utilization of Prunus armeniaca L.. Based on the Geographic Information System software platform combined with the MaxEnt Model, we simulated the potential distribution areas and the degree of adaptation of Prunus armeniaca L. in the Yili River Valley, and predicted the potential distribution changes of Prunus armeniaca L. in the future under different situations. Based on the above methods, the following results were obtained: (1) The MaxEnt Model simulated the geographic distribution of Prunus armeniaca L. with high accuracy and an AUC value of 0.969, and the area of the currently suitable area for Prunus armeniaca L. in the Yili River Valley was about 10407.77 km2, accounting for about 18.45% of the overall land area of the Yili River Valley; the area of the highly suitable area was about 1380.9 km², accounting for about 13.26%, the area of the medium suitable zone is about 2830.15km², and the area of low suitable zone is about 6196.05km². (2) The maximum increase in the total area of the suitable zone under the future low-radiation forcing scenario is 11.49%, and the minimum increase under the future medium-high forcing scenario is 4.94%. (3) The overall migration was in the southwest direction, with the largest migration angle under the SSP245 scenario and the largest migration distance under the SSP585 scenario. Under the background of future climate change, there is a tendency for the potential habitat of Prunus armeniaca L. in the Yili River Valley to expand from low altitude to high altitude, and altitude is the dominant geographic factor influencing the distribution of Prunus armeniaca L.. By simulating and studying the potential geographic distribution of Prunus armeniaca L. in the Yili River Valley under the background of climate change, we can reveal the response mechanism between the geographic distribution of Prunus armeniaca L. and the natural environment, which can provide scientific guidance and data support for the exploitation and protection of Prunus armeniaca L. in the future.

This research focuses on the use of the HEC-RAS model to estimate flash flood risk. It combines advanced hydraulic modeling techniques and precise data entry. The aim is to contribute knowledge to assess flash flood risk and reduce impacts on communities and infrastructure. The selection of study areas with a history of severe flooding, such as the Lam Saphung Basin, Phrom River Basin, and Lam Chern River Basin Part 1 in Thailand, highlights the importance of thorough flash flood risk assessment. By leveraging the HEC-RAS model, the results of this research inform proactive risk management strategies, improve emergency preparedness and help develop sustainable mitigation measures. The results are important in developing emergency response strategies and overall recovery ability in areas at risk of flash floods. The research combines advanced hydrologic modeling and real-world flash flood data. In addition to the flood condition assessment, the extent of the flood area and associated hazards were assessed using a two-case simulation strategy. The study covers future scenarios related to land use changes and retrospective analysis of past flood events. The results have practical implications for improving emergency response strategies, land use planning, and overall resilience in flash flood-prone areas. The integrated approach emphasizes the research output to providing insights and actionable solutions for communities facing ongoing challenges posed by flash floods.

Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

Abstract: A biomaterial is proposed for closing extensive bone defects in the maxillofacial region. The composition of the biomaterial includes high-molecular chitosan, chondroitin sulfate, hyaluronate, heparin, alginate and inorganic nanostructured hydroxyapatite. The purpose of the study is to demonstrate morphological and histological early signs of reconstruction of a bone cavity of critical size. The studies were carried out on 84 white female rats weighing 200-250 g. The study group consisted of 84 subjects in total, 40 in the experimental group and 44 in the control group. In all animals, three-walled bone defects measuring 0.5 x 04 x 05 cm were applied subperiosteally in the region of the angle of the lower jaw and filled in experimental group using lyophilized gel mass of chitosan-alginate-hydroxyapatite (CH-SA-HA). In control animals, the bone cavities were filled with an auto-blood clot after bone trepanation and bleeding. The observation periods are 3.5.7 days, 2.3.4.6.8 and 10 weeks. The control of bone regeneration was carried out using multiple morphological and histological analyses. Results showed that following implantation the chitosan construct actively replaced early-stage defects with the formation of a full-fledged new bone tissue as compared to the control group. Already, by the 7th day morphological analysis showed that formation of spongy bone tissue could be seen. After 2 weeks there was a pronounced increase in bone volume (P<0.01), and at 6 weeks after surgical intervention the closure of the defect was 70-80%, after 8 weeks - 100% without violation of bone morphology with a high degree of mineralization. Thus, the use of modified chitosan after filling eliminates bone defects of a critical size in the maxillofacial region, reveals early signs of bone regeneration, and serves as a promising material in reconstructive dentistry.

The study was performed to get the first insight of distribution of the low field volume magnetic susceptibility (MS) throughout the Zagreb city area, based on in-situ field measurements. Most interesting locations were selected for soil sampling and geochemical content was determined using ICP-OES. A geostatistical approach was applied on MS and geochemical results. Median value of 0.245 x 10-3 SI units is proposed to be used as relevant average MS value in Zagreb area. Mean concentrations of heavy metals in Zagreb soils (in µg/g) are: Pb (36.82), Zn (87.77), Cu (30.84), Cd (0.66), Cr (29.04), Co (11.89) and Ni (28.40), being relatively low in comparison with Croatian legislation and with European and world average. Boxplot analyses showed that 45% of studied elements do not show any anomaly, while the rest of elements mostly show only one weak anomaly and they are located at the same sites as MS anomalies. Statistical analysis found significant correlations between MS and following elements: Cd, Co, Fe, Mn, Na, Pb, Sb and Zn. In-situ MS measurements proved to be an efficient tool for initial screening of large areas in terms of elevated heavy elements concentrations, enabling cheap and fast assessment of state of environment.

The current regeneration mode of public space in the old city of Guangzhou is ineffective, thus necessitating supplementation with a more systematic methodology. The “plug-in design” targets sustainable regeneration while preserving the overall urban texture and context, i.e., has little impact on the spatial qualities of the old city. The ultimate goal is to activate the public space of the old city of Guangzhou point-to-area through the insertion of various plug-ins. In this study, the methodology is applied to Xudi Gaodi Street, the core area of the old city of Guangzhou, to explore its effects on sustainability. The internal public space is isolated and supplied with rigid and flexible plug-ins from multiple dimensions, which not only improves the spatial environment but also injects new urban formats. This work provides a specific solution for regeneration in Guangzhou’s old city while enhancing empirical knowledge of the plug-in design to support urban regeneration theory and further practical development.

Remote sensing (RS) technology has significantly contributed to geological exploration and mineral resource assessment. However, its effective application in vegetated areas encounters various challenges. This paper aims to provide a comprehensive overview of the challenges and opportunities associated with RS-based lithological identification in vegetated regions. The article begins by introducing the sources and processing methods of RS data, which serve as the foundation for subsequent analysis. Moreover, it highlights the techniques and methodologies employed for lithological classification in vegetated areas. Notably, hyperspectral RS and Synthetic Aperture Radar (SAR) have emerged as prominent tools in lithological identification. In addition, this paper addresses the limitations inherent in RS technology, including issues related to vegetation cover and terrain effects, which significantly impact accurate lithological mapping. To propel further advancements in the field, the paper proposes promising avenues for future research and development. These include the integration of multi-source data to enhance classification accuracy and the exploration of novel RS technologies and algorithms. In summary, this paper presents valuable insights and recommendations for advancing the study of RS-based lithological identification in vegetated areas.

The merge areas of freeway work zones include relatively significant safety hazards that have continuously led to urgent safety issues to be solved by the management departments. In order to make up for the cumbersome process of independent identification of rear-end collision and lane change collision on complex road sections, an appropriate identification method of traffic conflicts in the merge area of freeway work zone was explored, this study collected vehicle running tracking data from the merge areas of multiple work zones, using an unmanned aerial vehicle video technique. Based on an inter-frame difference method and the principle of a spatio-temporal context visual tracking algorithm, the vehicles were detected and tracked, and the coordinate data of the vehicles in continuous motion were parsed using MATLAB extension tools. Based on the behavior characteristics of vehicle conflict avoidance, a new identification method for evading severe traffic conflicts is proposed according to the initial velocity, acceleration and accident rate of section traffic. Then, a statistical analysis was performed on the spatial distribution characteristics of the traffic conflicts in typical merge areas. The impacts of the road conditions in work zones, vehicle factors, and traffic flow factors on the traffic conflicts were analyzed. A binomial logistic model was established to identify the main influencing factors. The results show that in the merge area of the freeway work zone, there are serious traffic conflicts between vehicles in the following two situations: (Ⅰ) v∈[7,13.5] m/s and a∈[-3.96,-0.65]m/s2; and (Ⅱ) v∈[13.5,24.3] m/s, and a∈[-3.96,-1.57] m/s2. The probabilities of serious traffic conflicts in the first and last 25 m of the merge area are greater than those in the other sections. The smaller the space between the upstream work zone and the merge area, the greater the probability of serious traffic conflicts between vehicles. When the average vehicle speed is relatively high, the probability of serious conflicts is the highest, i.e., by a multiple of 5.95 from the baseline. Moreover, the probability of serious conflicts between vehicles is higher for larger vehicles, i.e., 4.765 times that for small vehicles. The research results can serve as a reference for freeway management departments to improve the safety levels of merge areas during road work. For example, the probability of serious conflicts can be effectively reduced by setting up reasonable speed limit signs in the work zone, increasing the spacing between work zone and merge area, and appropriately diverting large vehicles.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

In past years, lithium-ion batteries (LIBs) can be found in every aspect of life, and batteries, as energy storage systems (ESSs), need to offer electric vehicles (EVs) more competition to be accepted in markets for automobiles. Thick electrode design could reduce the use of non-active materials in batteries that its energy density would be improved and its cost would be cut. However, thick electrodes are limited by their weak mechanical stability and poor electrochemical performance, these limitations could be classified as the critical cracking thickness (CCT) and the limited penetration depth (LPD). The understanding of the CCT and the LPD have been proposed and the recent works on breaking the CCT and improving the LPD are listed in this article. By comprising these attempts, some thick electrodes could not offer higher mass loading or higher accessible areal capacity that would defeat the purpose.

Conventional methods of crop mapping need ground truth information to train the classifier. Thanks to the frequent acquisition allowed by recent satellite missions (Sentinel 2), we can identify temporal patterns that depend on both phenology and crop management. Some of these patterns are specific to a given crop and thus can be used to map it. Thus, we can substitute ground truth information used in conventional methods with agronomic knowledge. This approach was applied to identify irrigated permanent grasslands (IPG) in the Crau area (Southern France) which play a crucial role in groundwater recharge. The grassland is managed by making three mows during the May-October period which leads to a specific temporal pattern of leaf area index (LAI). The mowing detection algorithm was designed using the temporal LAI signal derived from Sentinel 2 observations. The algorithm includes some filtering to remove noise in the signal that might lead to false mowing detection. A pixel is considered a grassland if the number of detected mows is greater than 1. A data set covering five years (2016-2020) was used. The detection mowing number was done at the pixel level and then results are aggregated at the plot level. A validation data set including 780 plots was used to assess the performances of the classification. We obtained a Kappa index ranging between 0.94-0.99 according to the year. These results were better than other supervised classification methods that include training data sets. The analysis of land-use changes shows that misclassified plots concern grasslands managed less intensively with strong intra-parcel heterogeneity due to irrigation defects or year-round grazing. Time series analysis, therefore, allows us to understand different management practices. Real land-use change in use can be observed, but long time series are needed to confirm the change and remove ambiguities with heterogeneous grasslands.

A healthy park-people relation depends essentially on the fair and sustainable maintenance of rural livelihood. When protected area is designated, rural people may face restrictions of access to land and resource use for multiple ecosystem services. In Wuyishan of China, we analysed the role of traditional tea cultivation during consistent protected area management to find ways to maintain stability of this social-ecological system in the new national park era. We used an intensive social survey to investigate tea’s role, perception of ecosystem services and impacts on tea cultivation from consistent conservation policies. Results showed that tea cultivation brought major household income and associated with multiple culture services. Protected area management affected land use and conservation outcomes were more obvious to farmers than economic and social ones. From the perspective of a social-ecological system, tea cultivation in national should be conservation-compatible activities from which the potentially lost economic value is remedied by ecological and cultural valorisation. To sustain the resilience of the social-ecological system, we proposed a three-scale management framework to regulate biophysical elements at land plot scale, to link production and market at the mountain level, and to secure tenure and encourage community participation at the landscape level.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

Public green and open spaces fulfil various social, ecological, economic, and aesthetic roles, which complement each another, but can also compete with one another. COVID-19 pandemic catalysed multiple societal changes, including citizens’ perception, needs and expectations posed towards urban green spaces. This article discusses the extent to which the temporally and geographically changed patterns of experiencing these natural spaces also influenced users’ perception and behaviour as well as their appreciation of the conservation areas. The study is based upon two surveys carried out in the greater metropolitan region of Vienna, the capital city of Austria. A quantitative survey (representative online panel) among Viennese population (n=1012), as well as qualitive interviews with experts responsible for conservation areas, administrators of federal parks, along with NGOs representatives were carried out in spring and summer 2021. Our study shows the changed use of urban and suburban large green spaces and conservation areas: first, from the perspective of those responsible for the areas as well as the visitors. Both perspectives supplement one another. They highlight also changed perception of urban citizens towards green spaces during COVID-19 pandemic. An increased importance of time spent in nature (68%) and possibility to visit large green areas (67%) was reported by Viennese citizens. Also, higher recognition of green spaces located close to home was observed among 69% of the respondents. Thus, the presented study contributes to the ongoing international discussion on the transition of societal needs and its effects on urban green spaces induced by the pandemic. Presented results deliver solid arguments highlighting the need of urgent transformation towards a more sustainable, resilient and healthy urban space.

The relative operating characteristic (ROC) curve is a popular diagnostic tool in forecast verification, with the area under the ROC curve (AUC) used as a verification metric measuring the discrimination ability of a forecast. Along with calibration, discrimination is deemed as a fundamental probabilistic forecast attribute. In particular, in ensemble forecast verification, AUC provides a basis for the comparison of potential predictive skill of competing forecasts. While this approach is straightforward when dealing with forecasts of common events (e.g. probability of precipitation), the AUC interpretation can turn out to be oversimplistic or misleading when focusing on rare events (e.g. precipitation exceeding some warning criterion). How should we interpret AUC of ensemble forecasts when focusing on rare events? How can changes in the way probability forecasts are derived from the ensemble forecast affect AUC results? How can we detect a genuine improvement in terms of predictive skill? Based on verification experiments, a critical eye is cast on the AUC interpretation to answer these questions. As well as the traditional trapezoidal approximation and the well-known bi-normal fitting model, we discuss a new approach which embraces the concept of imprecise probabilities and relies on the subdivision of the lowest ensemble probability category.

Disease-related data and information collected by physicians, patients, and researchers seem insignificant at first glance. Still, the same unorganized data contain valuable information that is often hidden. The task of data mining techniques is to extract patterns to classify the data accurately. One of the various Data mining and its methods have been used often to diagnose various diseases. In this study, a machine learning (ML) technique based on distributed computing in the Apache Spark computing space is used to diagnose diabetics or hidden pattern of the illness to detect the disease using a large dataset in real-time. Implementation results of three ML techniques of Decision Tree (DT) technique or Random Forest (RF) or Support Vector Machine (SVM) in the Apache Spark computing environment using the Scala programming language and WEKA show that RF is more efficient and faster to diagnose diabetes in big data.

For public safety and physical security, currently more than a billion closed-circuit television (CCTV) cameras are deployed around the world. Proliferation of artificial intelligence (AI) and machine learning (ML) technologies has gained significant applications including crowd surveillance. The state-of-the-art distance and area estimation algorithms either need multiple cameras or a reference scale as a ground truth. It is an open question to obtain an estimation using a single camera without a scale reference. In this paper, we propose a novel solution called E-SEC, which estimates interpersonal distance between a pair of dynamic human objects, area occupied by a dynamic crowd, and density using a single edge camera. The E-SEC framework comprises edge CCTV cameras responsible for capture a crowd on video frames leveraging a customized YOLOv3 model for human detection. E-SEC contributes an interpersonal distance estimation algorithm vital for monitoring the social distancing of a crowd, and an area estimation algorithm for dynamically determining an area occupied by a crowd with changing size and position. A unified output module generates the crowd size, interpersonal distances, social distancing violations, area, and density per every frame. Experimental results validate the accuracy and efficiency of E-SEC with a range of different video datasets.

The study of the area model of Pinus tabulaeformis forest provides an important reference for improving the management of Pinus tabulaeformis and revealing the growth law of Pinus tabulaeformis. According to the classification method proposed by Munro, stand growth and harvest prediction models are divided into three categories: full stand model, single wood model and diameter distribution model. Based on the fixed sample data of Shangluo Pinus tabulaeformis, the spatial instead of time method is used to process the data, and the weight coefficient of each model in the combined prediction model is calculated by using the optimal weighting method. The single wood model, the whole forest model and the diameter distribution model are combined by the combined prediction method to integrate the fault area prediction of Pinus tabulaeformis forest. The results show that the combined prediction method is more accurate than the single model (single wood model, whole forest model and diameter distribution model). At the same time, the method can improve the compatibility of the forest break area prediction model, ensure the consistency of the forest break area prediction, and provide a new direction for the research of forest resource monitoring and investigation.

Research shows that stress, a common problem in dense cities, can be relieved in the natural environment. As great significance has been attached to the urban environment and public health in the society, this paper aims to study the relation and interaction between the perceived sensory dimension of urban park green space, attention restoration and state empathy. Therefore, we conducted an on-site questionnaire survey in four typical parks in Chengdu in terms of age, sex, daily stress, frequency of access in parks and other basic information of the respondents. The main part consists of perceived dimension, state empathy and attention restoration. The software SPSS24.0 is applied to the test of the validity and reliability of the PSD Scale, and then the important correlation between the perceived sensory dimensions in the parks and visitors' attention restoration is analyzed through multiple linear regression. Finally, the moderation effect of state empathy is tested by PROCESS. The findings show that (1) only seven dimensions in the PSD Scale are effective; (2) Serene and Refuge in the perceived sensory dimensions have significant effect on the restorative components of attention. (3) Except the dimensions of Rich in Species and Refuge, empathy enhanced the moderation effect in the interaction between the other five dimensions the Perceived Restorative Scale(PRS), especially in the interaction between the dimension Social and PRS. However, this study needs to be further explored to provide scientific basis and design strategy guidance for the research on the restoration potential of urban park green space in high-density urban areas.

The coronavirus disease (COVID-19) pandemic is rapidly spreading across the world. In Democratic Republic of Congo (DRC), 11 out of 26 provinces have been affected on 19 June 2020. The purpose of this study was to assess the public views, attitudes and beliefs related to the COVID-19 pandemic among the population of an unaffected city.Methods: This is a descriptive observational study conducted in an unaffected city using a questionnaire. Findings: A total of 769 people participated. The average age was 36 ±14 years. The sex ratio (male: female) was 1.6. The majority of respondents (97%) is aware of the existence of the COVID-19 pandemic, it is well informed about the signs of the disease, its severity and barrier measures, however few of them have adopted the change in habit and behavior in respect of the barrier measures. Lack of water for handwashing is the most common difficulty in complying with barrier measures (71%). The COVID-19 is considered as an artificial virus designed to reduce the world population by 26%, God’s punishment (22%). Only 36% of the participants are in favor of vaccination against COVID-19. Vaccine is, a western conspiracy to spread COVID-19 in Africa (38%), testing it on Africans (35%), sterilize Africans’ people (12%).Conclusions: Cities not yet affected by COVID-19 in DRC are aware of the existence of the disease, but insufficiently prepared to deal with it. It is important to increase awareness on barrier measures, combating false information, and improving regular water supply for regular handwashing.

Introduction: Oral health knowledge, beliefs and attitudes of parents have a direct influence on their child’s oral health maintenance, dietary habits and encourage healthy behaviors. The aim of this study was to assess the knowledge, and attitude of parents with regards to the oral health practice of their children and its associated factors. Methods: A self -administered structured questionnaire was administered to parents or guardians of learners aged 5 to 12 years at a low socio-economic rural primary school in the uGu district, KwaZulu Natal, South Africa to collect demographic variables, knowledge of dental health, use of toothbrush, use of toothpaste, dietary practices and dental visits; practice with respect to dental care and attitudes towards oral health. The questionnaire was translated from English to IsiZulu was used. Bivariate and multivariate logistic regressions were used to assess the association between parent’s sociodemographic factors with their oral health knowledge and practice scores. Results: One hundred and forty four completed survey instruments were received with an eighty percent (118) representation of mothers. Ninety five percent of the parents (136) had a positive attitude towards oral health with 86% (124) of the children brushed their tongue and 89% (128) of the children brushed their teeth happily. The mean knowledge score was 70% with a median of 72%. Children were significantly more likely to brush their tongues (AOR: 3.20 95% CI: 1.06-9.66) and were more likely to be happier when brushing their teeth (AOR: 4.65 95% CI: 1.41-15.38) when the caregivers were their mothers, and when parents had an above average knowledge score (AOR: 1.86 95% CI: 0.72-4.85) and had positive attitudes (AOR: 3.20 95%CI: 0.46-22.00). Conclusion: To reduce the gaps in knowledge, oral health promotion should be integrated into all point of care contact with parents at health facilities, increased community awareness and advertising campaigns as well as a more focused school health oral program that addresses primary prevention, screening and appropriate referrals to health facilities

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

Cocoa is an important commodity crop not only to produce one of the most complex products such as chocolate from the sensory perspective, but one that commonly grows in developing countries close to the tropics. This paper presents novel techniques applied using cover photography and a novel computer application (VitiCanopy) to assess the canopy architecture of cocoa trees in a commercial plantation in Queensland, Australia. From the cocoa trees monitored, pod samples were collected, fermented, dried and grinded to obtain the aroma profile per tree using gas chromatography. The canopy architecture data were used as inputs in an artificial neural network (ANN) algorithm and the aroma profile considering six main aromas as targets. The ANN model rendered high accuracy (R = 0.82; MSE = 0.09) with no overfitting. The model was then applied to a satellite image from the whole cocoa field studied to produce canopy vigor and aroma profile maps up to the tree-by-tree scale. The tool developed could aid significantly the canopy management practices in cocoa trees that have a direct effect on cocoa quality.

A risk of ischemic stroke increases exponentially after menopause. Even a mild-ischemic stroke can result in increased frailty. Frailty is a state of increased vulnerability to adverse outcomes, which subsequently increases risk of cerebrovascular events and severe cognitive decline, particularly after menopause. Several interventions to reduce frailty and subsequent risk of stroke and cognitive decline have been proposed in laboratory animals and patients. One of them is whole body vibration (WBV). WBV recuperates cerebral function and cognitive ability that deteriorates with increased frailty. The goal of the current study is to test the efficacy of WBV in reducing post-ischemic stroke frailty and brain damage in reproductively senescent female rats. Reproductively senescent Sprague–Dawley female rats were exposed to transient middle cerebral artery occlusion (tMCAO) and randomly assigned to either WBV or control groups. Animals placed in the WBV group underwent 30 days of WBV (40 Hz) treatment performed twice daily for 15 min each session, 5 days each week. The motor functions of animals belonging to both groups were tested intermittently and at the end of treatment period. Brains were then harvested for inflammatory markers and histopathological analysis. The results demonstrate a significant reduction in inflammatory markers and infarct volume with significant increases in brain-derived neurotrophic factor and improvement in functional activity after tMCAO in middle-aged female rats that were treated with WBV as compared to the control group. Our results may facilitate a faster translation of the WBV intervention for improved outcome after stroke, particularly among frail women.

This paper considers the problem of quantifying the quality of a model selection problem for a graphical model. The model selection problem often uses a distance measure such as the Kulback-Leibler (KL) distance to quantify the quality of the approximation between the original distribution and the model distribution. We extend this work by formulating the problem as a detection problem between the original distribution and the model distribution. In particular, we focus on the covariance selection problem by Dempster, [1], and consider the cases where the distributions are Gaussian distributions. Previous work showed that if the approximation model is a tree, that the optimal tree that minimizes the KL divergence can be found by using the Chow-Liu algorithm [2]. While the algorithm minimizes the KL divergence it does not minimize other measures such as other divergences and the area under the curve (AUC). These measures all depend on the eigenvalues of the correlation approximation measure (CAM). We find expressions for KL divergence, log-likelihood ratio, and AUC as a function of the CAM. Easily computable upper and lower bounds are also found for the AUC. The paper concludes by computing these measures for real and synthetic simulation data.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Eastern boundary upwelling systems feature strong zonal gradients of physical and biological ocean properties between cool, productive coastal oceans and warm, oligotrophic subtropical gyres. Zonal currents and jets (striations) are therefore likely to contribute to the transport of water properties between coastal and open oceanic regions. Multi-sensor satellite data are used to characterize the signatures of striations in sea surface temperature (SST), salinity (SSS), and chlorophyll-a (Chl-a) in subtropical eastern North/South Pacific (ENP/ESP) upwelling systems. In the ENP, tracers exhibit striated patterns extending up to ~2500 km offshore. Striations in SST and SSS are highly correlated with quasi-zonal jets, suggesting that these jets contribute to SST/SSS mesoscale patterns via zonal advection. Chl-a striations are collocated with sea surface height (SSH) bands, a possible result of mesoscale eddy trains trapping nutrients and forming striated signals. In the ESP, striations are only found in SST and coincide with SSH bands, consistently with quasi-zonal jets located outside major zonal tracer gradients. An interplay between large-scale SST/SSS advection by the quasi-zonal jets, mesoscale SST/SSS advection by the large-scale meridional flow and eddy advection may explain the persistent ENP hydrographic striations. These results underline the importance of quasi-zonal jets for surface tracer structuring at the mesoscale.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

The migration from MATLAB to Python (M-to-PY) has gained significant traction in recent computational research. While MATLAB has long served as a linchpin in myriad scientific endeavors, there's an emerging trend to rejuvenate these projects using Python's extensive AI tools and libraries. This study presents a semi-automated process for M-to-PY conversion, using a detailed case study of an image skeletonization project comprising fifteen MATLAB files and a 1404-image dataset. Skeletonization is foundational for ongoing 3D motion detection research using AI transformers, predominantly developed in Python. The utilization of ChatGPT-4, acting as an AI co-programmer, is pivotal in this conversion. By leveraging the public OpenAI API, we developed an M-to-PY converter prototype, evaluated its efficacy using test cases from the Bard bot, and subsequently employed the converted code in an AI application. The dual contributions encompass a well-tested M-to-PY converter and a Skeleton App capable of sketching and skeletonizing any given image, enriching the AI toolset. This study accentuates how AI resources, like ChatGPT-4, can simplify code transitions, opening doors for innovative AI implementations using primarily MATLAB-coded scientific research.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

The world has been highly impacted by the COVID-19 as the virus has spread to all continents – about 200 countries in total. The latest update claims about 4,000,000 confirmed cases and about 300,000 confirmed deaths owing to the COVID-19 pandemic. This probably makes the COVID-19 as the most dangerous contagious disease in the era 2000s. Apart from massive publications on this topic, there is no available qualitative analysis that describes the dynamic spreads of the COVID-19 and its impacts on healthcare and the economy. Through the system archetypes analysis, this paper explains that the dynamic spread of the COVID-19 consists of the limits to growth and the success to successful structures. The limits to growth elucidates that more symptomatic and asymptomatic patients owing to infected droplets may be bounded by self-healing and isolated treatments. The success to successful structure explains that once the COVID-19 affects the economy through the lockdown, there will be a limited fund to support the government aids and the aggregate demand. In overall, this paper gives readers simplified holistic insights into understanding the dynamic spread of the COVID-19.

Background Telomere shortening is related to aging and unfavourable health outcomes. Obesity and metabolic diseases are important factors for accelerating aging. This study aimed to find out the association between obesity, metabolic disease, and telomere length in metabolically healthy adults. Methods 237 adults were enrolled with written consents at a health promotion centre of a tertiary hospital from February 2014 to March 2015. After excluding 99 subjects who met the exclusion criterion, a total of 130 metabolically healthy subjects were selected for final analysis. The subjects were divided into quartile groups according to the telomere lengths of their oral mucosal cells. Results The subjects consisted of 66 (50.8%) males with a mean age of 58.59 years. The body mass index (BMI, kg/m2) increased significantly along with the quartile groups (Q1, 23.00; Q2, 23.96; Q3, 23.70; Q4, 25.20; P-for trend=0.008). Waist circumference (WC, P-for trend=0.022), waist-to-hip ratio (WHR, P-for trend=0.005), and waist-to-height ratio (WHtR, P=0.001) also increased along with the quartile groups. Obesity prevalence (BMI ≥25 kg/m2), abdominal obesity (WC ≥90 cm for men, ≥85 cm for women), WHR 〉1.0 for men or 〉0.85 for women, and WHtR ≥0.5 increased significantly as the telomere length increased (P-for trend <0.05). After adjusting for covariates, the ORs for each obesity markers increased as the telomere length increased (P-for trend <0.05); and the ORs of WHtR were especially meaningful (Q1, 1.00; Q2, 2.53; Q3, 2.97; Q4, 7.81; P-for trend = 0.001). There were no significant trends for metabolic syndrome and its components along with the prevalence of fatty liver disease. Conclusion Obesity markers and telomere length had significant positive correlation despite the established theory. The obesity paradox may exist in metabolically healthy adults with regard to telomere length, However, further studies with larger sample sizes for the association between obesity and telomere length are needed.

Nuʻupia Ponds, a traditional Hawaiian fishpond system, are located at Marine Corps Base Hawaii (MCBH) and part of the Nuʻupia Ponds Wildlife Management Area, a wetland refuge for native, endangered, and protected birds and Hawaiian green sea turtles, as well as many native fish species. Currently, there is uncertainty regarding the ecological status and condition of the fishponds following prior modification of wetland habitats in and around the ponds. This study examines circulation dynamics and characterizes water exchange, pond volume, and residence time across the full tidal spectrum at Nuʻupia fishponds. Our results indicate a general west to east gradient in current flow; with higher flushing rates and lower residence times of fishponds in the western ponds of the Nu’upia system compared to the eastern ponds. We further found low flushing rates at several sites causing limited water exchange with Kāne’ohe Bay, as well as within Nu’upia Pond system. Sufficient water circulation plays a fundamental role in maintaining a healthy balance of fishpond flora and fauna and preserve ecosystem health. The results from this study provide a baseline of current physical water circulation dynamics and implications for ecosystem health, as well as inform science-based conservation and management strategies moving forward.

Keywords: pelvic ultrasound, follicle number per ovary, FNPO, ovarian volume, PCOM, upper normal limits, referral population

This paper proposes a new method for network screening on rural low-volume roads. These roads are important as they provide critical access to agricultural land and tourist attractions. Most low-volume roads belong to the lowest functional class (local rural roads) and thus are built to lower design standards. The conventional hot spot network screening techniques may not be appropriate for low-volume roads due to the sporadic nature of crashes occurring on these roads. Contrarily sophisticated network screening approaches require extensive roadway and traffic data that are often unavailable to local agencies for lack of resources, and/or lack of technical expertise. This research attempts to address these obstacles in low-volume roads network screening which aims to identify candidate sites for safety improvements. The research used an extensive low-volume road sample from the state of Oregon and the Empirical Bayes expected number of crashes in developing the proposed models for network screening. The proposed models do not require exact measurement of roadway geometric features as all geometric variables were classified into categories that are easy to compile by local agencies. Further, the method could be used with and without traffic data, without compromising the effectiveness of the network screening process.

In the field of computational fluid dynamics (CFD) for rotorcraft, two significant challenges are resolving the complex vortex structures in rotor wakes, and representing the moving rotor blades in the ambient airflow. This study addresses the first challenge by using a third-order unstructured finite volume solver, which, compared to its second-order counterpart, has substantially lower dissipation. Consequently, even relatively coarse meshes are capable of resolving small vortices. With this background flow field solver, the second challenge is addressed by modeling each rotor as an Actuator Disk Model (ADM), or describing individual rotor blades as actuator lines, designated as the Actuator Line Model (ALM). Both of these models are equipped with an improved correction for aerodynamic losses at blade tips, which is thoroughly presented in the methodology section. The numerical experiments section centers on analyzing errors linked to various sampling approaches. Additionally, the article discusses comparisons between vortex theory and ALM, specifically regarding calculations for fixed-wing aircraft. Furthermore, high-order precision and parallel efficiency are exemplified in scenarios encompassing rotors engaged in both hovering and forward flight rotors. The results in this paper demonstrate that the combination of the ALM/ADM with the improved tip loss correction and the third-order finite volume solver presents a new way of developing efficient tools for the aerodynamic analysis of helicopter rotors.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p&lt;.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p&lt;.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p&lt;,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

Human serum albumin (HSA) is the ultimate, homeostatic determinant of fluid volume (FV) in all compartments of the body. The ability to change the pressure and flow of nutrient medium to cellular structures selectively has clinical significance in almost all areas of clinical medicine. We have shown that present fluid therapy (FT) using either colloid or saline dilutes nutrients. HSA binds and delivers nutrients, a lack of HSA binding causes Albumin Binding Disease (ABD) changing both colloidal pressure and nutrients leading to symptoms of sepsis. A reduction in HSA binding can be through lack of HSA or external ligands taking up binding sites on HSA. Many diseases cause ABD when immunoglobulins, infectious particles and by products bind to HSA including COVID-19 and other bacterial diseases like streptococcus as well as metabolic and cardiac disease due to incorrect pressure and nutrients. To raise HSA binding potential and remove vulnerabilities to these diseases we propose raising HSA. We show how present methods of fluid therapy (FT) are inefficient in that control of both pressure and nutrients forms initial equilibrium in the liver. HSA production and binding to nutrients is maintained at a level by the pressure in hepatocytes with the pancreatic and adrenal hormones moderating. Glucose and Ke-tone production are critical in the management of HSA binding and control of blood, colloidal pressure, and health of cells. Ketones provide a distinct mechanism of liver to lungs-heart metabolism during hypoglycaemia and activity. This known chain of nutrition becomes critical during disease like acute respiratory distress syndrome (ARDS) when ketones may be overproduced. HSA must therefore be infused into the liver to raise HSA levels safely. We investigated the control of HSA as a product of the actions of pressure in hepatocytes and changes in pancreatic and adrenal hormones. We found that in addition to pressure during glucose abundancy HSA is re-leased with ketones on administration of insulin and consider that this mechanism retains HSA moderation. HSA can therefore be increased by increasing insulin in the presence of glucose in the correct amounts. We suggest a protocol to increase FV, blood, lymph volume by infusion of HSA, insulin, and glucose direct to the liver so that the level of HSA stabilises. We suggest this will raise all other nutrients in the new FV, blood, lymph culminating in the creation of new blood cells. We propose that in a clinical situation maintaining this protocol will alleviate the symptoms of ABD and decrease the likelihood of serious illness and death.

Background: Evaluating muscle mass and function among stroke patients is important. However, evaluating muscle volume and function is not easy due to the disturbance of consciousness and paresis. Temporal muscle thickness (TMT) has been introduced as a novel surrogate marker for muscle mass, function, and nutritional status. We herein performed a narrative literature review on temporal muscle and stroke to understand the current meaning of the TMT in the clinical stroke practice. Methods: The search was performed in PubMed, last updated in October 2021. Report on temporal muscle morphomics and stroke-related diseases or clinical entities were collected. Results: Four studies reported on TMT and subarachnoid hemorrhage, 2 intracerebral hemorrhage, 2 ischemic stroke, 2 standard TMT values, and 2 nutritional status. TMT was reported as a prognostic factor for several diseases, surrogate markers for skeletal muscle mass, and an indicator of nutritional status. Computed tomography, magnetic resonance imaging, and ultrasonography were used to measure TMT. Conclusions: TMT is gradually used as a prognostic factor of stroke or surrogate marker for skeletal muscle mass and nutritional status. Establishing standard methods to measure TMT and large prospective studies to investigate the further relationship between TMT and diseases are needed.

In 2019, Chinese government implemented the first round of National Centralized Drug Procurement (NCDP) pilot (so-called "4+7" policy) in mainland China, achieved a prominent price reduction of 52% on average for 25 bidding winning products. Under cross-price elasticity theory, the price behavior of pharmaceutical enterprises for policy-related drugs might change. This study used drug purchasing data from the Centralized Drug Procurement Survey in Shenzhen 2019, and applied single-group Interruption Time Series (ITS) design to examine the impact of "4+7" policy on the drug price index (DPI) of policy-related drugs. The ITS analysis showed that the DPI of winning (-0.183 per month, p&lt;0.0001) and non-winning (-0.034 per month, p=0.046) products significantly decreased after the implementation of "4+7" policy. No significant difference was found for the immediate change of DPI for alternative drugs (p=0.537), while a significant decrease in change trend was detected in the post-"4+7" policy period (-0.003 per month, p=0.014). The DPI of the overall policy-related drugs significantly decreased (-0.261 per month, p&lt;0.0001) after "4+7" policy. These findings indicate that the price behavior of pharmaceutical enterprises changed under NCDP policy, while the price linkage effect is still limited. It is necessary to further expand the scope of centralized purchased drugs and strengthen the monitoring of related drugs regarding price change and consumption structure.

This work examines the effects of two problematic trends in diesel passenger car emissions – increasing NO2/NOx ratio by conversion of NO into NO2 in catalysts and a disparity between the emission limit and the actual emissions in everyday driving – on ambient air quality in Prague. NO2 concentrations were measured by 104 membrane-closed Palmes passive samplers at 65 locations in Prague in March-April and September-October of 2019. NO2 concentrations measured by city stations during those periods were comparable with the 2016-2019. The average measured NO2 concentrations at the selected locations, after correcting for the 18.5% positive bias of samplers co-located with a monitoring station, were 36 µg/m3 (range 16-69 µg/m3, median 35.3 µg/m3), with the EU annual limit of 40 µg/m3 exceeded at 32% of locations. The NO2 concentrations have correlated well (R2=0.76) with the 2019 average daily vehicle counts, corrected for additional emissions due to uphill travel and intersections. In addition to expected “hot-spots” at busy intersections in the city center, new ones were identified, i.e. along a six-lane road V Holešovičkách. Comparison of data from six monitoring stations during March 15-April 30, 2020 travel restrictions with the same period in 2016-2019 revealed an overall reduction of NO2 and even a larger reduction of NO. The spatial analysis of data from passive samplers and time analysis of data during the travel restrictions both demonstrate a consistent positive correlation between traffic intensity and NO2 concentrations along/near the travel path. The slow pace of NO2 reductions in Prague suggests that stricter vehicle NOx emission limits, introduced in the last decade or two, have so far failed to sufficiently reduce the ambient NO2 concentrations, and there is no clear sign of remedy of Dieselgate NOx excess emissions.

In thermal friction drilling (TFD) operations, the geometrical dimensions of bushing shape, height and wall thickness are the most vital consequences, due to increasing the connecting length and strength. In this paper, AA7075-T651 aluminum alloys with 2, 4, 6, 8, and 10 mm in thicknesses were drilled with TFD process in order to investigate the density, the volume ratio, and height and wall thickness of the bushings. The experiments were conducted at constant spindle speed and feed rate conditions by using HSS conical tools of 5, 10, 15, and 20 mm in diameters. It was experimentally found that the bushing height and the wall thickness were tendency of increase linearly with increasing both material thickness and tool diameter. The effect of tool diameter was found to have much of influence on the measured values than the thickness of the drilled material. The density of the bushing was changed inconsiderably. Approximately 70-75 % percentages of the evacuated material composed the bushing shape, in TFD operations.

Bistatic radar experiments have been used to study surface characteristics of extra-terrestrial bodies in the Solar System, including the Moon, Venus, Mars, and Titan. This paper proposes a 3D model to characterize the scattered field of a Gaussian rough surface on an extra-terrestrial body for an orbital bistatic radar configuration. Specifically, this model will investigate how the variability of surface roughness impacts the spectral broadening of the received signal using physical optics approximations and ray tracing on a surface model using a facet approach with Gaussian properties. A linear relationship between spectral broadening of the signal and surface roughness was found. This relationship is in line with results obtained by commonly used analytical models for bistatic radar on planetary surfaces.

Solar energy is one of the most important renewable energy sources for many settings, such as households, solar-powered vehicles, power grid support, etc. However, the amount of solar energy produced is directly proportional to the surface area of the solar panel exposed to the sun rays, and so the challenges arise for the space required to install solar panels in order to get maximum area coverage of sun radiation energy absorption in constricted spaces such as vehicles powered by solar, small residential apartments, etc. The challenge with solar energy is that once a plate is installed, the space under it or above it cannot be used for another solar panel installation. This is due to the fact that the shadow cast by the above solar panel or structure prevents sun rays from reaching the below solar panel. The introduction of flexible solar panels that can take on any shape has given us the opportunity to explore the possibility of maximising solar plate surface area using surface manifold techniques. In this optimisation study, the constraint is that we have a space with fixed dimensions of length, width, and height, and the objective is to maximise the surface area of the panel within the given space dimensions to maximise solar energy absorption. Thus, this paper then proposes curving the panel surface and/or protruding the surfaces of the panel using the concept of a topology surface manifold to maximise the surface area: Protruding panel surface with shapes such as pyramidal, cone, hemisphere, sinusoidal wavy curve, etc. are analysed to check if the panel surface increases at all. The geometrical design result shows that the panel surface can increase by more than 20%. Although this paper only presents concept work and details of experimental design are yet to be performed, it should also be noted that curving surfaces have drawbacks, such as some protruding parts of solar panels when the plate is tilted, not facing the sun directly, which may cast shadows on parts of the solar panel, causing hindrance.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Coalescence of nanowires and other three-dimensional structures into continuous film is desirable for growing low dislocation density III-nitride and III-V materials on lattice-mismatched substrates, and interesting from the fundamental viewpoint. Here, we develop a growth model for vertical nanowires which, under rather general assumptions on the solid-like coalescence process within the Kolmogorov crystallization theory, results in a morphological diagram for the asymptotic coverage of a substrate surface. The coverage is presented as a function of two variables, the material collection efficiency on the top nanowire facet a, and the normalized surface diffusion flux of adatoms from the NW sidewalls b. The full coalescence of nanowires is possible only when a=1 regardless of b. At a&gt;1, which is usual for vapor-liquid-solid growth with a catalyst droplet, nanowires can only partly merge but never coalesce into continuous film. These results can be used for predicting and controlling the degree of surface coverage by nanowires and three-dimensional islands by tuning the surface density, droplet size, adatoms diffusivity, and geometry of the initial structures in the vapor-liquid-solid, selective area or self-induced growth processes in different epitaxy techniques.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.