The Agricultural Policy/Environmental eXtender (APEX) model is widely used for evaluating agricultural conservation efforts and their effects on soil and water. A key component of APEX application in Korea is simulating water quality impacts of rice paddies because rice agriculture claims the largest cropland area in the country. In this study, a computational module called APEX-Paddy is developed to simulate water quality with considering pertinent paddy management practices such as puddling, flood irrigation management. Data collected at two experimental paddy sites in Korea were used to calibrate and validate the model. Results indicate that APEX-Paddy performs well in predicting runoff discharge rate and nitrogen yield while the original APEX highly overestimates runoff rates and nitrogen yields on large storm events. With APEX-Paddy, simulated and observed flow and mineral nitrogen yield (QN) are found to be highly correlated after calibration (Nash & Sutcliffe Efficiency (NSE) = 0.87 and Percent Bias (PBIAS) = −14.6% for flow; NSE = 0.68 and PBIAS = 2.1% for QN). Consequently, the APEX-Paddy showed a greater accuracy in flow and QN prediction than the original APEX modeling practice using the SCS-CN method.

Drinking water, in addition to the best-known chemical and biological agents, contains radionuclides of both natural and artificial origin, which can contribute significantly to the overall effective dose received by the population. The Italian Decree Law 28/2016, implementing 2013/51/EURATOM Directive, establishes the activities for risk management and the parameter values for different radionuclides activity concentrations. In addition to the institutions involved, annually the National Inspectorate for Nuclear Safety and Radiation Protection (ISIN), publishes the monitoring reports of environmental radioactivity in Italy, including radioactivity in drinking water. The purpose of the study was to integrate ISIN reports with 2018 to 2020 data by collecting measurements performed by institutional laboratories to obtain a more complete information and adding, for the Campania region, some data not yet published. This new updated report was not significantly different from ISIN’s one, meaning that those publications are nevertheless extremely representative of the radioactivity in Italian drinking water. However, the study allowed to obtain a more detailed data also including measurements not considered in ISIN reports, for instance, radon-222 activity concentrations. This may be of great usefulness for all radiation protection stakeholders in order to ensure environmental protection, pollution prevention and the population safety.

Current problem facing researchers globally is microplastics as well as toxic chemical pollution of the ecosystem. Microplastics carry toxic chemicals in the ecosystem.serving as a vector for transport. In this study, a review of the literature has been conducted with the following objectives: (1) to summarise the concentrations of toxic chemicals such heavy metals and hydrophobic organic contaminants sorped on microplastics; (2) to evaluate their spatial distribution regarding adsorbed contaminant (3) to discuss plausible mechanism by which microplastics adsorp or desorp toxic chemicals in the environment; (4) to discuss implications of their occurrence in air, water and soil media; and (5) to discuss the impact of ingested microplastics to human health. Microplastics are ubiquitous environmental contaminant. Concentrations of sorped toxic chemical varied with location which represents a local problem; industrialized areas (especially areas experiencing crude oil related activities or have history of crude oil pollution) have higher concentrations than less industrialized areas. Ingestion of microplastics has been demonstrated in a range of marine and soil organisms as well as edible plants, thus possible contaminating the base of the food-web. Potential health effect to human is by particle localization, chemical toxicity and microbal toxins. We conclude by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

As the increase threat of flood risk and environmental safety due to the urbanization, Sponge city research has been attracting extensive attention both in practical and theoretical research field. To date, there are only scattered studies about Sponge city. Moreover, vary names of Sponge city prevalent in different countries, which leads to disconnection of literature in the same field of Sponge city. In this paper, a thorough systematic literature mining of Sponge city is presented. A literature analysis system is created, which includes literature export from Web of Sciences and systematic analysis via NoteExpress and CiteSpace. Some literature statistical results are derived. Challenges and opportunities for future research are anticipated. Our goals are to promote this promising thought, summarize past research, and identify issues for future research to create impacts on the practice of Sponge city.

This study aimed to compare the effects of adding fermented feed to daily feed on slaughter performance, meat quality, and flavor compounds of cage chickens. Control group (CK) of the Guangxi Partridge chicken received a standard base diet (CK), pellets added with 10% fermented banana peel (Pe-10), 20% fermented banana peel (Pe-20), 10% fermented banana pulp residue (Pu-10) and 20% fermented banana pulp residue (Pu-20). The slaughter performance, meat quality, and flavor compounds in the meat samples of the chicken in these groups were evaluated. The results showed that the chicken in Pe-10, Pe-20, Pu-10, and Pu-20 had pectoral muscle percentages, thigh muscle percentages, and total fatty acids content of chest meat higher than CK. The moisture content, meat color, carcass weight, total net weight, and abdominal fat percentages of the meat samples in these experimental groups were not remarkably different. The flavor compounds in the meat samples of the chicken fed with the two concentrations of fermented banana peel and banana residue were significantly different from those in the control group. When the amount of fermented banana peel added to the daily feed increased from 10% to 20%, the flavor compounds in the chicken samples changed significantly. In conclusion, different proportions of fermented banana peels and dregs in diets can improve slaughter performance and chicken quality and affect its flavors.

Conflict between agricultural water resources and socio-economy development is a global problem. Accurate evaluation of coordinated development of agricultural water resources and socio-economy and risk mitigation is necessary for sustainable development. An evaluation method, including selection of criteria, data collection, determination of weight, evaluation of coordinated development, prediction of parameters, and judgment of coordinated development state, has been proposed to study coordinated development degree. To deal with uncertainties, Monte Carlo method and fuzzy set method were used. The method is demonstrated to solve a real-world evaluation problem in Shanxi Province in the middle of China. Results show that coordinated development degrees were (0.7, 0.8) for most of the cities of Shanxi in 2015, indicating that coordinate development state was intermediate coordinate. To achieve balanced development, more attention should be put on socio-economic development in Taiyuan and Yanquan, and agricultural water resources utilization in Jinzhong, Yuncheng and Xinzhou. The average coordinated development degree is 0.758, and coordinate development state was intermediate coordinate from 2006 to 2015. Coordinated development degree has a trend of decreasing markedly, coordinate development state will be barely coordinated, and agricultural water resources utilization lags behind socio-economic development in 2020. The study demonstrates the practicability of the improved method, by evaluating coordinated development degree under uncertainty and forecasting future risks, which will conduce to promote sustainable development of agricultural water resources and socio-economy.

Oilfield produced water (OPW) is used to boost freshwater sources for crop irrigation in California's agriculturally important Central Valley. OPW is known to contain salts, metals, hydrocarbons, alkylphenols, naturally radioactive materials, biocides, and other compounds from drilling and production processes. Less is known about the potential uptake and accumulation of these compounds in crops and soil irrigated with OPW. In this study 23 potted mandarin orange plants were irrigated 2-3 times weekly (depending on season) with water containing three different concentrations of the known OPW heavy metals barium, chromium, lead, and silver. Seven sets of samples of soil and leaves and all fruits were collected and processed using microwave-assisted digestion (EPA Method 3051A). Processed samples were analyzed using ICP-OES. ANOVA, ANCOVA, and Tukey’s honest significant difference test were used to examine the effects of metal concentrations in the irrigation water, sample number, and number of watering days on the metal concentrations in the soil, leaf, and fruit samples. Accumulation of barium in soil and leaves was strongly positively associated with sample and number of watering days, increasing nearly 2,000-fold. Lead also showed an upward trend, increasing up to 560-fold over baseline level. Chromium showed an increase in the soil that tapered off, but less consistent results in the leaves and fruit. The silver results were more volatile, but also indicated at least some level of accumulation in the tested media. The smallest absolute accumulation was observed for chromium. Concentrations in the fruit were highest in the peel, followed by pith and juice. Accumulation of all heavy metals was generally highest in the soil and plants that received the highest irrigation water concentration. Considering the potential for adverse human health effects associated with ingesting soluble barium contained in food and drinking water, and to a lesser extent chromium and lead, the study signals that it is important to conduct further research into whether OPW contaminants can enter the food chain and pose risks to consumers.

The study presented hereafter shows a new methodology to reveal traces of polyethylene (the most common microplastic particles, known as a structure of C2H4) in a sample of ocean water by the irradiation of a 50 keV, 1 µA electron beam. This is performed by analyzing the photon (produced by the electrons in water ) fluxes and spectra (i.e. fluxes as a function of photon energy) at different types of contaminated water with an adequate device and in particular looking at the peculiar interactions of electrons/photons with the potential abnormal atomic hydrogen (H), oxygen (O), carbon (C), phosphorus (P) compositions present in the water, as a function of living and not living organic organisms with a PO4 group RNA/DNA strands in a cluster configuration through a volumetric cells grid.

Soil moisture plays a crucial role in various hydrological processes and energy partitioning of the global surface. The Soil Moisture Active Passive-Sentinel (SMAP-Sentinel) remote sensing technology has demonstrated a great potential in monitoring soil moisture at a scale greater than 1 km. This capability can be applied to improve weather forecast accuracy, enhance water management for agriculture, and climate-related disasters. Despite the techniques increasing used worldwide, its accuracy still requires field validation in specific regions like Thailand. In this paper, we report on extensive in-situ monitoring of soil moisture (from surface up to 1 m depth) at 10 stations across Thailand spanning the years 2021 to 2023. The aim was to validate SMAP surface soil moisture (SSM) Level 2 product over a period of two years. Using one month averaging approach, the study revealed linear relationships between the two measurement types, with the coefficient of determination (R-squared) varying from 0.13 to 0.58. Notably, areas with more uniform land use and topography such as croplands tended to have a better coefficient of determination. We also conducted detailed soil core characterization, including soil-water retention curves, permeability, porosity, and other physics properties. These soil properties were then used for estimating the correlation constants between SMAP and in-situ soil moistures using multiple linear regression. The results demonstrated R-squared values between 0.933 and 0.847. An upscaling approach of SMAP was proposed which showed a promising results when using 3-month average of all measurements in cropland together. The finding also suggest that the SMAP-Sentinel remote sensing technology exhibits significant potential for accurate soil moisture monitoring in diverse applications. Further validation efforts and research, particularly in terms of root zone depths and area-based assessments, especially in the agricultural sector, can greatly improve the technology’s effectiveness and usefulness in the region.

We describe the direct formation of mixed-phase (1T and 2H) MoS2 layers on Si as a photocathode via atomic layer deposition (ALD) for application in the photoelectrochemical (PEC) reduction of water to hydrogen. Without typical series-metal interfaces between Si and MoS2, our p-Si/SiOx/MoS2 photocathode showed efficient and stable operation in hydrogen evolution reactions (HERs). The resulting performance could be explained by spatially genuine device architectures in three dimensions (that is, laterally homo and vertically heterojunction structures). The ALD-grown MoS2 overlayer with the mixed-phase 1T and 2H homojunction passivates light absorber and surface states and functions as a monolithic structure for effective charge transport within MoS2. It is also beneficial in the operation of p-i-n heterojunctions with inhomogeneous barrier heights due to the presence of mixed-phase cocatalysts. The effective barrier heights reached up to 0.8 eV with optimized MoS2 thicknesses, leading to a 670 mV photovoltage enhancement without employing buried Si p-n junctions. The fast-transient behaviors via light illumination show that the mixed-phase layered chalcogenides can serve as efficient cocatalysts by depinning the Fermi levels at the interfaces. A long-term operation of ~ 70 h was also demonstrated in a 0.5 M H2SO4 solution.

Pollutants accumulate in aquatic habitats as a result of mining activities. Lemna gibba and Lemna minor were used in this study to examine the accumulation capacities of Mo+, Pb+, and Cu++ in the acid fluids of the copper mining. Duckweed family includes water plants like L. minor and L. gibba. These are tiny, delicate, free-floating aquatic plants. Two reactors were assigned to L. gibba and L. minor, respectively. Throughout the course of eight days, these plants and reactor water were gathered every day. The acid mine water's pH, temperature, and electric conductivity were also tested every day. The L. gibba and L. minor were cleaned, dehydrated, and burned in a drying oven for a whole day at 300 oC. ICP-MS (Inductively Coupled Plasma Mass Spectroscopy) was used to determine the Mo+, Pb+, and Cu++ content of the plant and water samples. The concentrations of Mo, Pb, and Cu in the acid mine fluids of the copper mining were 30±4, 260±12, and 15535±322 μg L−1, respectively.in that order. When it came to extracting Mo, Pb, and Cu from the acidic fluids of the copper mining, L. gibba and L. minor performed well and efficiently compared to control samples; they did so 29 and 177 times for Mo, 30 and 109 times for Pb, and 495 and 1150 times for Cu. Considering all these findings, it has been shown that L. gibba and L. minor have the ability to efficiently remove Mo, Pb and Cu in acid mine fluids and can be good rehabilitation plants for polluted waters.

Water is an essential commodity to sustain life. The condition of water in Tiruchirappalli was measured using different Physicochemical parameters like Temperature, pH, TDS, Total Solids, Salinity, Total Hardness, and Electrical Conductivity. Water samples were collected from different places in Tiruchirappalli city, Tamil Nadu. Water samples were examined by different chemical methods. According to the results, Thiruvarambur-1 showed comparatively higher results in the case of every parameter compared to other sampling stations. Obtained results were further interpreted using statistical tools. Considering ECs as a principal component for the regression and correlation analysis with other parameters significant correlation was found. A strong correlation was observed between ECs and TDS, Total Hardness, Turbidity, and Salinity.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

Heavy metals and organic pollutants are ubiquitous environmental pollutants affecting the quality of soil, water and air. Over the past 5 decades, many strategies have been developed for the remediation of polluted water. Strategies involving aquatic plant use are preferable to conventional methods. In this study, an attempt was made to provide a brief review on recent progresses in research and practical applications of phytoremediation for water resources with the following objectives: (1) to discuss the toxicity of toxic chemicals pollution in water to plant, animals and human health (2) to summarise the physicochemical factors affecting removal of toxic chemicals such as heavy metals and organic contaminants in aqueous solutions by aquatic plants; (3) to summarise and compare the removal rates of heavy metals and organic contaminants in aqueous solutions by diverse aquatic plants; and (4) to summarise chemometric models for testing aquatic plant performance. More than 20 aquatic plants specie have been used extensively while duckweed (L. minor), water hyacinth (Eichhornia crassipes), water lettuce (P. stratiotes) are the most common. Overall, chemometrics for performance assessment reported include: Growth rate (GR), Growth rate inhibition (% Inhibition), Metal uptake (MU), translocation/transfer factor (TF), bioconcentration factor (BCF), Percent metal uptake (% MU), Removal capacity (RC) and Tolerance index (TI) while absorption rate have been studied using the sorption kinetics and isotherms models such as pseudo-first-order (PFO), pseudo-second-order (PSO), Freundlich, Langmuir and Temkin. Using modeling and interpretation of adsorption isotherms for performance assessment is particularly good and increases level of accuracy obtained from adsorption processes of contaminant on plant. Conclusion was drawn by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

Ca2+ is a crucial second messenger in plant cells, playing a vital role in various physiological and biochemical processes, including plant growth and development, photosynthesis, and enzyme regulation. Exogenous calcium concentration can have different effects on plant growth. This study aimed to investigate the optimal calcium concentration for the growth of four tree species, namely Pinus tabuliformis, Pinus sylvestris var. mongolica, Populus, and Morus alba seedlings, and whether the optimal calcium concentration varies among different tree species. The study utilized five calcium concentration gradients (0, 100, 200, 400, 800 mg·kg-1) for each species with three repeated treatments. Various growth indexes, photosynthetic parameters, chlorophyll fluorescence parameters, water use efficiency, and antioxidant enzyme activities were assessed to determine each species' calcium concentration requirements. The results showed that exogenous calcium significantly affected the growth and development of each seedling. The growth, biomass, photosynthetic parameters, photosynthetic products, photosynthetic pigments, water use efficiency, and antioxidant enzyme activity all increased initially and then decreased with increasing calcium concentration. Leaf calcium concentration also increased with the exogenous calcium content. Thus, there is an optimal calcium concentration for plant growth, and high or low calcium concentration is not conducive to plant growth. Furthermore, the study found that different tree species have varying optimal calcium concentrations. The optimal calcium concentration for Pinus tabuliformis, Pinus sylvestris var. mongolica, Populus, and Morus alba seedlings was 100, 100, 200, and 400 mg·kg-1, respectively. Finally, the study revealed that broadleaf species require higher calcium concentrations than coniferous species.

The Colorado and Mississippi River Basins are crucial for water supply, agriculture, and ecological stability in the U.S., yet climate change, water management practices, and energy sector demands pose significant challenges to their sustainability. This paper highlights the potential of leveraging the Voluntary Carbon Market (VCM) to address these challenges by creating new revenue streams and incentivizing sustainable water management practices. The paper provides high-level estimates by extrapolating from existing literature. The results suggests that water projects in these basins could generate over 45 million carbon credits annually, potentially attracting around $4.5 billion in investments over the next decade. However, challenges such as high costs, complex regulations, and stakeholder coordination must be addressed. The paper also identifies opportunities for advancing water resiliency projects, including increasing public awareness, engaging corporations, and utilizing innovative financing mechanisms. Recommendations include promoting the VCM-water relationship, encouraging methodology innovation, developing pilot programs, investing in digital monitoring technologies, and conducting localized analysis to optimize carbon credit potential in water management. By integrating carbon markets with water management strategies, the paper suggests significant contributions to global climate goals and enhanced water resilience in these critical regions.

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

The Korean water deer (WD), the dominant wildlife species in South Korea, is classified as vul-nerable on the IUCN Red List. Beside their several unique characteristics, they have a lower in-cidence of tick bites compared to other Cervidae species, particularly roe deer (RD). In natural environments, ticks exhibit questing behavior by waiting on grasses to climb onto host's hair coat. They use sensory organs to detect signals such as body temperature and chemicals from the host's skin, then move to preferred feeding location. Therefore, we conducted a comparative analysis of the skin tissue and hair features of both species to compare the factors leading to lower incidence of tick bites in WD. Notably, WD had significantly larger blood vessels, sebaceous glands, and sweat glands which maintain the barrier functions of the skin (p≤0.004), irregular scale surfaces in hair cuticles, and stiff and 2.83-times thicker primary hair diameter (p<0.001). Each parameters made the ticks difficult to move onto the epidermis of WD. To our knowledge, this is the first report which is focused on the comparative analysis for skin and hair feature in WD and RD. We suggest that these differences may attribute to evade tick bites in WD.

Recently, NOAA has included GNSS (Global Navigation Satellite System) Radio Occultation (RO) data as one of the crucial long-term observables for weather and climate applications. To include more GNSS RO data in the numerical weather prediction system, the NOAA Commercial Weather Data Pilot program (CWDP) started to explore the commercial RO data available on the market. After two rounds of pilot studies, the CDWP decided to award the first Indefinite Delivery Indefinite Quantity (IDIQ) contract to GeoOptics and Spire Incs. in 2020. This study examines the quality of Spire data products for weather and climate applications. Spire RO data are collected from commercial CubeSats through careful comparison with the data from Formosa Satellite Mission 7–Constellation Observing System for Meteorology, Ionosphere, and Climate-2 (COSMIC-2), ERA-5, and high-quality radiosonde data. The results demonstrated that although with lower Signal-Noise-Ratio (SNR) in general, the pattern of the lowest penetration height for Spire is similar to those for COSMIC-2. The Spire and COSMIC-2 penetrate heights are between 0.6 and 0.8 km altitude at the tropical oceans. Although using different GNSS RO receivers, the precision of Spire STRASP receivers is of the same quality as those of COSMIC-2 Global Positioning System - GPS, GALILEO, and GLObal NAvigation Satellite System – GLONASS (TGRS) receivers. The retrieval accuracy from Spire is very compatible with those from COSMIC-2. We validated Spire temperature and water vapor profiles by comparing them with collocated radiosonde data. Generally, over the height region between 8 km and 16.5 km, the Spire temperature profiles match those from RS41 RAOB very well with temperature biases &lt; 0.02 K. Over the height range from 17.8 to 26.4 km, the temperature differences are ~-0.034 K with RS41 RAOB being warmer. We also estimated the error covariance matrix for Spire, COSMIC-2, and KOMPSAT-5. Results showed that the COSMIC-2 estimated error covariance values are slightly more significant over the oceans at the mid-latitudes (45oN-30oN and 30oS-45oS), which may also be owing to COSMIC-2 SNR being lower at those latitudinal zones.

Leakages in the water distribution networks (WDNs) are real problems for utilities and other governmental agencies. Timely leak detection and location identification has been a challenge. In this paper, an integrated approach to geospatial and infrared image processing method was used for robust leak detection. The method combines drops in flow, pressure, and chlorine residuals to determine potential water leakage locations in the WDN using Geographic Information System (GIS) techniques. GIS layers were created from the hourly values of these three parameters for the city of Sharjah provided by Sharjah Electricity, Water and Gas Authority (SEWA). These layers are then analyzed for locations with dropped values of each of the parameters and are overlaid with each other. In the case where there were no overlaying locations between flow and pressure, further water quality analysis was avoided, assuming no potential leak. In the case where there are locations with drops in flow and pressure layers, these overlaying locations are then examined for drops in chlorine values. If overlaying locations are found, then these regions are considered potential leak locations. Once potential leak locations are identified, a specialized remote sensing technique can be used for precise leak location. This study also demonstrated the suitability of using an infrared camera for leak detection in a laboratory-based setup. This paper concludes that the following methodology can help water utility companies in the timely detection of leaks, saving money, time, and effort.

Anthropogenic activity like Industrialization has unleashed vast quantities of organic pollutants, including heavy metals. The hazardous heavy metals can cause cancer, neurocognitive defects and wide-ranging health problems. The pollutants resist environmental degradation and can often accumulate in the environment. Microbial degradation of pollutants is a potentially efficient solution for pollution remediation. Amongst the heavy metals, lead contamination resulting from anthropogenic activity have resulted in tragic consequences since the advent of human civilization, even in 21^st century as demonstrated by the Flint water crisis in the US. Bioremediation of lead from the environment could be attempted by various strategies, including mitigation of human activity that causes it in the first place. Microbiome, specifically bacteria, mediated bioremediation can serve as a potent platform for remediating environmental pollution with heavy metals such as lead. Herein we will review the mechanisms and methods of microbial bioremediation of environmental heavy metals with a focus on lead and highlight the challenges and opportunities.

Within the research of pressure pipeline inspection methods there is an industry that is constantly growing and becoming more efficient. The purpose of inspection methods on pressure pipelines comes back to the issue of resolving leaks, corrosion, and inability of a pipeline to function (eventually). Evidently, these issues can hurt the environment, the public using the material being carried out by these pressure pipelines such as natural gas or petroleum and can hurt the pockets of pipeline companies that did not react quick enough to their pipeline solely for the reason that they may have not noticed there was an issue with their pressure pipeline. In-line inspection methods are continuously growing and have already made an impact to prevent the catastrophes that occur when a pipeline is not maintained. Technology such as smart pigs, MFLs, and ultrasounds are the future of pressure pipeline inspection. This research paper explains their pros and cons and how they’re overall more efficient and preferred as the primary inspection method for a pipeline. Older, more traditional methods such as aerial inspection, by-foot inspection, hydrostatic pressure testing, and Direct Assessment does not cover every base of inspection like in-line inspection technology does and this research explains why that is and the areas of where in-line inspection technology can be improved and deemed not as useful. This is where trenchless renewal and replacement methods come into play with inspection methods and determining the characteristics of a pipeline that matches with which inspection method and which trenchless method to use. The future of inspection methods for pressure pipelines is attainable and is somewhat already here, this research discusses the new emerging technologies and how designing in-line inspection technology to be cheaper and more versatile with pipeline characteristics can make everyone a winner in the future. A winner as far the environment being safe, neighborhoods near pressure pipelines being safe, companies being able to install in-line inspection technology at a fraction of the cost of today and the efficiency of pipelines by monitoring the characteristics with this new technology.

One of the main challenges in the treatment of industrial wastewater is the removal of oil-in-water emulsions, which are stable and therefore difficult to treat. Bacterial cellulose (BC) has structural characteristics that make it an ideal filtration membrane. The present study investigated the effectiveness of a BC membrane filtration system for the treatment of oily industrial wastewaters. The results demonstrated that BC is highly effective at removing oily contaminants (~99%), reducing the colour and particulate matter of wastewater, as well as eliminating nearly the entire microbiological load (~99%). SEM, MEV, FTIR, XRD, and TGA demonstrated the presence of oil in the interior of the membrane after filtration, characteristic peaks of its chemical composition, and a 40% reduction in crystallinity. TGA revealed an increase from three (pre-filtration) to five (post-filtration) stages of thermal degradation, indicating the retention of the contaminant in the BC. The mechanical tests demonstrated that the membrane has tensile strength of 72.13 ± 8.22 MPa and tolerated elongation of up to 21.11 ± 4.81% prior to tearing. The BC membrane also exhibited excellent flexibility, as it could be folded &gt; 100 times at the same point without exhibiting signs of tearing. The BC surpasses traditional methods, such as activated charcoal and effluent treatment stations, in the removal of emulsified oils. The findings demonstrate that BC is promising for the treatment of industrial wastewaters, which is a field that requires continual technological innovations to mitigate the environmental impacts of the oil industry.

The escalating global demand for clean water has propelled research into sustainable and cost-effective purification methods. Activated carbon (AC) derived from biowaste materials presents an environmentally friendly and economically viable solution for water treatment. This review article provides an extensive overview of the synthesis techniques, characterization methods, and applications of biowaste activated carbon (BAC) for water purification. It discusses the diverse sources of biowaste, such as agricultural residues, food waste, and biomass, and explores various activation methods including physical, chemical, and biological processes. Furthermore, the article examines the adsorption mechanisms, performance factors, regeneration strategies, and emerging trends in BAC synthesis and application. Insights from this review can guide future research endeavors and facilitate the development of sustainable water purification technologies.

This study deals with the preparation of adsorbents from a commercial xerogel by chemically modifying its surface with concentrated mineral acids and alkali metal chlorides, their physicochemical characterization, and their use as adsorbents for gallic acid in aqueous solution. The prepared adsorbents have a high specific surface area (347-563 m2 g-1), better pore development for samples treated with alkali metal chlorides than with mineral acids and are more acidic than the initial xerogel (p.z.c range 2.49-6.87 vs. 7.20). The adsorption properties of the commercial xerogel improved over a wide range of pH and temperature. The experimental results indicate that the adsorption process is thermodynamically favored.

Abstract: Rotavirus (RV) it’s the agent of one of the main causes of severe viral gastroenteritis in the pediatric population, being responsible for a significant portion of deaths related to diarrhea among children under five years. RV are identified as a potential reference pathogen and it is known that the persistence and infectivity of the viral particles can be related to environmental factors. The aim of the study was to identify and correlate the presence of Rotavirus in collective and individual water sources (deep tubular wells, shallow tubular wells, shallow dug wells, springs, surface water, rainwater stored in cisterns and water trucks that were collected from surface water) of rural communities in the state of Goiás, with the seasons in which the collections were made (rainy and dry season). For this, 86 water samples in the dry period and 160 samples in the rainy period were collected. Concentration of water samples, extraction of viral genetic material, cDNA synthesis and molecular tests (qPCR) were performed. When analyzing the presence of RV in the samples in relation to the period studied, RV was found to be more prevalent in the dry season (54.7%) than in the rainy season (20%), showing a strong statistical association with the dry season (p-value < 0.001). The proportion of positive samples in the dry period, considering the type of source, resulted in higher in Shallow dug wells (p-value <0.001), higher in surface waters (p = 0.001) and higher in spring water (p-value = 0.02). The presence of pathogenic microorganisms in water is a public risk problem, enabling the emergence of outbreaks, endemics and epidemics. In the present research, there was an association among the presence of Rotavirus and the dry period of the year, when compared to the rainy period. Describing or identifying the seasonal behavior of pathogens is important for prevention and attention to water treatment and help in the monitoring of the virus in the water sources.

Water microbial contamination is a serious issue that poses a risk to both animal and human health. 120 water samples collected from main water source and drinkers from a poultry farm. Different bacterial pathogens were isolated from water sources. Escherichia (E.) coli, Pseudomonas (P.) aureoginosa, (Salmonella) S. Typhimurim, Aeromonas (A.) hydrophila at different percentages. Variable degree of bacterial resistance to some commercial disinfectants commonly used to disinfect water system (iodine, terminator and H2O2). Nanoparticles were used to control bacteria in water. About the safety investigation for the prepared nanomaterials, the work results demonstrated that zinc oxide (ZnO) nanoparticles (NPs) exhibit the highest safety profile among the manufactured materials. The median fatal dose (LD50) for ZnO NPs was determined to be 3709 mg/kg body weight. In comparison, the LD50 values for zeolites and nanocomposites were 3251 mg/kg and 2658 mg/kg, respectively. Therapeutic dosages were estimated based on the LD50. Zeolite NPs, ZnO NPs and ZnO/zeolite NPs showing promising results in control of those bacteria. It was concluded that the escalating resistance of bacteria to disinfectants have led to a need to find alternative such as nanoparticles that proved promising results in control of pathogens, particularly it showed a safe effect on laboratory animals.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

In recent years, a large-scale afforestation campaign has taken place in Inner Mongolia, China, to control desertification and soil erosion. However, the water consumption associated with large-scale afforestation significantly impacts the water resources in Inner Mongolia, resulting in a substantial ecological risk. This study aimed to evaluate the ecological risk of water resources caused by afforestation in the region. In this study, based on land cover data, Normalized Difference Vegetation Index (NDVI) data, and meteorological data, used trend analysis, water balance equation, and Water resources Security Index (WSI) index to analyze the ecological risks of water resources caused by afforestation in Inner Mongolia from 2000 to 2020. The results show that:(1) The afforestation area in Inner Mongolia was 5.37×104 km2 in 2000-2020; (2) Afforestation in arid and semi-arid areas leads to the reduction of water resources. (3) Afforestation reduces water resources in the study area by 0.76×108m3/year; (4) ~76% of afforestation regions face ecological risks of water resources.

The coastal zone of Bangladesh covers an area of 47,201 square km, 32% of the country, around 35 million people are living coastal zone, where about 15 million are women (Ahmad, 2019). Though the women of this area have a significant contribution in aquaculture, food production and economic growth of Bangladesh, still the health issues of women remain ignored, especially sexual and reproductive health issue. Women and girls experience heightened vulnerabilities to reproductive health problems in coastal areas. In aiming to investigate the prevalence of vaginal problems in coastal area the study has been designed. The study followed retrospective cohort study as a study design and use percentile and regression analysis to draw the result of the study. The study found that 94% of women are experiencing vaginal problems in coastal villages in Bangladesh. This number is about 05 times higher than the non-coastal villages and it also found water use for hygiene practice as a significant role for high rate of vaginal diseases in coastal areas of Bangladesh

Cotton is an important plant since it provides raw materials for various in-dustry bracnhes. Even though cotton is generally tolerant of drought, it is af-fected negatively by long-term drought stress. This experiment was conduct-ed according to a completed randomized plots trial design with 3 replications to determine the upland cotton genotype’s reactions against drought under controlled conditions in the 2022 year. All genotypes were watered with 80 mL-1 of water (100% irrigation, Field capacity) until three true leaves ap-peared. After this period water stress was applied at limited irrigation of 75% (60 mL-1), 50% (40 mL-1), and 25% (20 mL-1) of field capacity. After the trial terminated at 52. Days, the cv. G56, elit line G44, G5, and commercial variety G86 genotype, respectively resulted in the highest Root Length (RL), and the G76 genotype resulted in the lowest RL followed by G41 and G35 elite lines. G1 cultivar showed the highest Root Fresh Weight (RFW), followed by G56, G44, G86, G51, and G88, respectively. The lowest RFW was also obtained in elite lines G76 and G41. The third drought morphological marker, the Num-ber of Lateral Roots (NLRs), was the highest in G44, followed by G86, Cv. G56, elite lines G13 and G5 genotype. The lowest NLRs value was obtained in genotype G47 and G76. The highest RDW means was obtained in elite line G5, followed by Cv. G56, elite line G44, G75 and cv. G90, while the lowes RDW mean obtained in elite line G76, G35, and local varieties G20 and G61. In the SL marker, the highest averages were recorded for genotypes G35, G15, G26, G67, and G56, respectively. In the SFW marker, the highest averages were observed in genotypes G15, G52, G60, G31, and G68, respectively. The lowest SL values were observed in genotypes G91, G72, G32, and G22. Simi-larly, the lowest SFW values were found in genotypes G83, G2, G75, and G91. In another shoot drought marker, Shoot Dry Weight (SDW), the highest val-ues were obtained in genotypes G35, G52, G57, G41, and G60, respectively. Conversely, the lowest SDW values were observed in genotypes G65, G91, G4, G20, and G22. In conclusion, the commercial varieties with high averages in roots, namely G86, G56, G88, and G90, and the genotypes G67, G20, G60, and G57 showing tolerance in shoots, are suggested to be potential parent plants for developing cotton varieties resistant to drought. Using the culti-vars found tolerant in the current study as parents in a drought-tolerant vari-ety development Marker-assisted selection (MAS) plant breeding program will increase the chance of success in reaching the target after genetic diversi-ty analyses are performed. It is highly recommended to continue the plant breeding program with the G44, G30, G19, G1, G5, G75, G35, G15, G52, G29, and G76 genotypes which show high tolerance in both root and shoot sys-tems.

Water deficit greatly affects global crop growth and productivity, particularly in water-limited environments like upland rice cultivation, leading to reduced grain yield. Plants activate various defense mechanisms during water deficit, involving numerous genes and complex metabolic pathways. Exploring orthologous genes, linked to enhanced drought tolerance, can aid functional validation in target species using genomic data from model organisms. Here, we studied the OsCPK5 gene in upland rice, an AtCPK6 ortholog from A. thaliana, by overexpressing it in the BRSMG Curinga cultivar. Transformants were assessed under two conditions: water deficit applied 79 days after seeding, lasting 14 days, followed by 7 days of irrigation at 80% field capacity. Physiological data and samples were collected at R3, R6, and R8 stages. GM plants consistently exhibited higher OsCPK5 gene expression across stages, peaking during grain filling. During this phase, GM plants displayed reduced stomatal conductance, photosynthetic rate, and increased water use efficiency compared to non-GM plants under drought. GM plants also exhibited higher filled grain percentage in both irrigation conditions. Their drought susceptibility index was 0.9 times lower than NGM plants, and they maintained a higher chlorophyll a/b index, indicating sustained photosynthesis. NGM plants under water deficit exhibited more leaf senescence, while OsCPK5-overexpressing plants retained green leaves. Overall, OsCPK5 overexpression induced diverse drought tolerance mechanisms, hinting at potential for future development of more drought-tolerant rice cultivars.

Maize, a crop of international relevance, frequently undergoes xylem embolism due to water shortage, negatively impacting growth, yield, and quality. Consequently, a refined comprehension of xylem embolism is vital for enhancing maize cultivation. Notwithstanding extensive research and the generation of analytical models for embolism mechanisms, prevalent models often disregard crop-specific hydraulic processes and the formation of embolisms via air bubbles in the xylem conduit. In this research, we present an inventive model applying pipe cavitation parameters to discern water potential and bubble formation in maize leaf xylem. The model integrates pivotal physiological traits of maize—leaf count, leaf vein count, and average leaf radius—demonstrating robust correlations. Furthermore, we constructed a percentage conductivity loss (PLC) curve based on pre-dawn leaf water potential and compared it with our model, offering interval data to observe embolisation events triggered by air bubbles. Utilizing experimental data, our novel cavitation-parameters based model effectively corresponds with observed bubble phenomena and appropriately characterizes water transport in plant xylem conduits. This method enabled us to observe the transition from bubble occurrence to cavitation embolism microscopically, which aligned with the embolism intervals provided by the model. This procedure reveals potential trends in bubble-induced embolism and deepens our knowledge of microscopic plant hydraulics and crop embolism. This work establishes a basis for understanding the generation of bubble embolisms in maize, assists in evaluating maize plant water status for efficient water supply management throughout the growth cycle, and contributes towards potential water management strategies for maize.

Polymer electrolyte membrane water electrolyser suffers mainly from slow kinetics regarding oxygen evolution reaction (OER). Noble metal oxides, like IrO2, RuO2, are generally more active for OER than metal electrodes, exhibiting low anodic overpotentials and high catalytic activity. However, issues like electrocatalyst stability under continuous operation and cost minimization through reduction of the catalyst loading are of great importance for the research community. In the present study, unsupported IrO2 of various particle sizes (different calcination temperatures) were evaluated for the OER and as anode electrodes for PEM water electrolyzers [1]. The elec-trocatalysts were synthesized by the modified Adams method [2][3] and the effect of calcination temperature on the properties of IrO2 electrocatalysts is investigated. Physicochemical charac-terization was conducted using X-ray Diffraction, BET, High-Resolution TEM and XPS analyses. For the electrochemical performance of synthesized electrocatalysts in the OER, cyclic voltammetry and linear sweep voltammetry were conducted in a typical 3-cell electrode configuration, using glassy carbon as working electrode, where the synthesized electrocatalysts were casted on, in 0.5 M H2SO4 solution. The materials, as anode PEM water electrolysis electrodes, were further evaluated in a typical electrolytic cell using Nafion®115 membrane as electrolyte and Pt/C as cathode elec-trocatalyst. The IrO2 electrocatalyst calcined at 400°C shows high crystallinity with 1.24 nm particle size, high specific surface area (185 m2 g-1) and a high OER activity of 177 mA cm-2 at 1.8 V as anode electrocatalyst for PEM water electrolyzer.

The gradual decline of the Aral Sea’s water level over the past five decades poses a huge environmental problem in the heart of Central Asia. Uzbekistan, once blessed with abundant water resources, now struggles with water scarcity in certain regions. While global environmental issues contribute to some degree to this dilemma, irrigation mismanagement plays a central role. This study focuses on the widespread problem of irrigation mismanagement in Uzbekistan and specifically addresses the rural district of Oltinsoy in the southern province of Surkhandarya. The main objective of this research project is to propose effective measures that can alleviate the pressing problem of water scarcity in the region while emphasizing the urgent need for well-executed projects and careful maintenance to ensure long-term sustainability at the local level. It is important to note that this study does not include an examination of the impact of global warming on the decline of water resources in Uzbekistan.

Aquifer water is the key staple to develop successful sustainable agricultural activity in newly reclaimed areas in Egypt. Monitoring irrigation water quality is necessary for a proper planning of this exhaustible resources. This work aims to evaluate the groundwater quality in the western newly reclaimed areas of Beni-Suef governorate. Fifty aquifer water sample were collected from wells scattered in the arid western Beni-Suef fringes during May of 2022. Water chemical analyses were conducted to estimate the parameters of Irrigation Water Quality Index (IWQI) namely the Electrical Conductivity (EC), Sodium (Na+), Chloride (Cl-), Bicarbonate (HCO3-) and the Adjusted percentage of Absorbed Sodium (SARo). The Inverse Distance Weighted (IDW) technique used to map the spatial distribution of aquifer water chemical characteristics and IWQI. The results showed that EC values were high in the south of the study area and decreased at its north and east borders. The results showed that the average of dissolved cations and anions were 236.4, 102, 77.5, 106.2, 309.6, 148.1 and 113 meq/l for Ca2+, Mg2+, Na+, K+, SO42-, HCO3-, and Cl-, respectively. Regarding to IWQI, its' values ranged from 28 to 81. Two-thirds of the study area classified as having moderate limitations for sustainable irrigation purposes. Furthermore, one-thirds of the area classified as having high restrictions.

Coagulation is the most sensitive step in drinking water treatment. Underdosing may not yield the required water quality, whereas overdosing may result in higher costs and excess sludge. Traditionally, the coagulant dosage is set based on bath experiments performed manually. Therefore, this test does not allow real-time dosing control, and its accuracy is subject to operator experience. Alternatively, solutions based on machine-learning (ML) have been evaluated as a computer-aided alternative. Despite these advances, there is open debate on the most suitable ML method applied to the coagulation process, capable of the most highly accurate prediction. This study addresses this gap, where a comparative analysis between ML methods was performed. As a research hypothesis, a novel data-driven fuzzy inference system (FIS) should provide the best performance due to its ability to deal with uncertainties inherent to complex processes. Although ML methods have been widely investigated, only a few studies report hybrid neuro-fuzzy systems applied to coagulation. Thus, to the best of our knowledge, this is the first study thus far to address the accuracy of this novel data-driven FIS for such application. The novel FIS provided the smallest error (0.86), indicating a promising alternative tool for real-time and highly accurate coagulant dosing in drinking water treatment.

Water distribution networks are vital infrastructure, needed for providing consumers with sufficient water of appropriate quality. The cost of construction, operation, and maintenance of such networks is extremely large. The problem of optimization of a water distribution network is governed by the type of water distribution network and the size of pipelines placed in the distribution network. This problem of the optimal diameter allocation of pipes in a distribution network has been heavily researched over the past few decades. This study describes the development of a computer program, ‘Smart Optimization Program for Water Distribution Networks’ (SOP–WDN), which applies Genetic Algorithm to the problem of the least-cost design of water distribution networks. SOP–WDN demonstrates the application of an evolutionary optimization technique, Genetic Algorithm, linked with a hydraulic simulation solver EPANET, for the optimal design of water distribution networks. The developed program was applied to three benchmark water distribution network optimization problems and produced consistently good results. SOP–WDN can be utilized as a tool for guiding engineers during the design and rehabilitation of water distribution pipelines.

Freshwater pond aquaculture is the prevailing fish culture system worldwide, especially in developing countries. Climate change outcomes and inadequate environmental practices challenge its sustainability. This study applies emergy synthesis to assess the environmental performance of freshwater pond aquaculture in Brazil, aiming to identify and propose practices towards sustainability. As a study model, nine semi-intensive lambari farms operating at three levels of management were evaluated: low (LC), moderate (MC) and high (HC) control. Results showed that the main inputs for LC were services (27-46%), feed (7-39%), and water (15-21%), while for the MC and HC farms, they were feed (35-49% and 17-48%, respectively) and services (33-39% and 26-36%, respectively). All farms required more than 60% of their emergy from purchased inputs, resulting in low emergy sustainability index (ESI = 0.1-0.5). Replacing animal protein and oil on diet composition by vegetal sources, using superficial water instead of springwater, increasing juvenile productivity, and controlling pond fertilization can lead all systems to higher efficiency and resilience, increasing sustainability.

TiO₂ nanorod as a superior nanostructure has attracted a lot of attention to exert in the photocatalytic and photoelectrocatlytic applications in recent years. Nevertheless, its practical usage is restricted by a number of limitations such as the large band gap energy, the low rate of photo-induced carriers generation and the high rate of charge carriers recombination. Therefore in this study, incorporation of TiO₂ nanorod with WO₃ is proposed as a suitable approach to overcome these defects. In this regard, WO₃-TiO₂ nanorod was constructed by a facile one pot hydrothermal method in two incessant steps and was then employed as a potent photoanode for photoelectrocatalytic hydrogen generation. The morphology, elemental compositions and optical properties were characterized by the FESEM, EDS and DRS analysis, respectively. Furthermore, voltammetry analyses were performed to assay the photoelectrochemical features of WO₃-TiO₂ nanorod. The results confirmed that the incorporation of TiO₂ nanorod with WO₃ not only significantly made the band gap energy narrower (from 3eV to 2eV), but also dramatically intensified the photocurrent density and photoconversion efficiency from 1mA.cm^-2 to 1.8mA.cm^-2 and from 0.3% to 0.45%, respectively. As a consequence of improving optical properties and photoelectrochemical features, WO₃-TiO₂ nanorod could generate 2.43 mmol H₂ during 100 min under UV irradiation, which was 1.71 times more than hydrogen generated over pure TiO₂ nanorod

The fabrication and characterisation of photo-anodes based on black-Si (b-Si) are presented using a photo-electrochemical cell in NaOH solution. Black-Si was fabricated by maskless dry plasma etching and was conformally coated by tens-of-nm of TiO2 using atomic layer deposition (ALD) with a top layer of CoO_x cocatalyst deposited by pulsed laser deposition (PLD). Low reflectivity R < % of Black-Si over the entire visible and near-IR (λ < 2 µm) spectral range is favourable in better absorption of light while an increased surface area facilities larger current densities. Photoelectrochemical performance of the heterostructured photoanode is discussed in terms of n-n junction between b-Si and TiO₂.

The “memory of water” experiments suggested the existence of molecular-like effects without molecules. Although no convincing evidence of modifications of water – specific of biologically-active molecules – has been reported up to now, consistent changes of biological systems were nevertheless recorded. We propose an alternate explanation based on classical conditioning of the experimenter. Using a probabilistic model, we describe not only the biological system, but also the experimenter engaged in an elementary dose-response experiment. We assume that during conventional experiments involving genuine biologically-active molecules, the experimenter is involuntarily conditioned to expect a pattern, namely a relationship between descriptions (or “labels”) of experimental conditions and corresponding biological system states. The model predicts that the conditioned experimenter could continue to record the learned pattern even in the absence of the initial cause, namely the biologically-active molecules. The phenomenon is self-sustained because the observation of the expected pattern reinforces the initial conditioning. A necessary requirement is the use of a system submitted to random fluctuations with autocorrelated successive states (no forced return to the initial position). The relationship recorded by the conditioned experimenter is, however, not causal in this model because blind experiments with an “outside” supervisor lead to a loss of correlations (i.e., system states randomly associated to “labels”). In conclusion, this psychophysical model allows explaining the results of “memory of water” experiments without referring to water or another local cause. It could be extended to other scientific fields in biology, medicine and psychology when suspecting an experimenter effect.

The megacities´ sewage creates socioeconomic dependence related to water availability in the nearby zones, especially in countries with hydric stress. The present paper studies the water balance progression of realistic scenarios from 2005 to 2050 in the Mezquital Valley, the receptor of Mexico City untreated sewage since 1886, allowing agriculture irrigation in unsustainable conditions. WEAP model calculated the water demand and supply. Validation was performed with outflows data of the Tula River and simulated three scenarios: 1st) Steady-state based on inertial growth rates, 2nd) Transient scenario concerned climate change outcomes, with minor influence in surface water and hydric stress in 2050; 3rd) Transient scenario perturbed with a planned reduction of 36% in the imported wastewater and the start-up of a massive Water Treatment Plant, allowing drip and sprinkler irrigation since 2030. In the 2005-2017 period, 59% of the agriculture depended on the flood irrigation with megacity sewage. The water balance scenarios evaluated the sectorial supply of the ground and superficial water. Drip irrigation would reduce 42% of agriculture demands, but still does not grant the downflow hydroelectric requirements, aggravated by the lack of wastewater supply since 2030. This research alerts about how present policies compromise future Valley demands.

The Safe Drinking Water Act Amendments of 1996 require community water systems in the United States to send consumers Consumer Confidence Reports (CCRs). CCRs contain information on detected contaminants and required educational information about drinking water. The authors of this study developed a survey to evaluate how utilities track consumer feedback, understanding, and the role of the CCR in shaping consumer perceptions about water quality. Responses from this survey indicate it is common for utilities to indirectly track the effectiveness of their CCRs, but few utilities indicated directly evaluating consumer understanding or the effect of CCRs on consumer perceptions.

The emission of mercury (II) from coal combustion and other industrial processes continues to be a concern and have local impact on water resources. The detection of these ions in water with sensitive but rapid testing methods is desirable for environmental screening and fieldwork. Nanoparticles of various chemistries have shown promise for this purpose, as they can be used in simple colorimetric analyses. Silver nanoprisms were chemically synthesized resulting in a blue reagent solution, that transitioned towards yellow and colorless solutions when exposed to Hg²⁺ ions at various concentrations. A rapid galvanic reduction of Hg²⁺ onto the nanoprism surfaces is apparently responsible for a change in shape towards spherical nanoparticles, leading to the change in color. There were no interferences by other metal ions in solution, and pH had minimal effect in the range of 6.5 to 9.8. The silver nanoprism reagent provided a detection limit of approximately 0.5 µM (100 µg/L) for mercury (II), which compares favorably with other nanoparticle-based techniques. Further optimization may reduce this detection limit.

The increasing occurrence of widespread drought phenomena is a global environmental emergency, especially for the effects of ongoing climate change on groundwater availability. Dry years and extreme temperatures are common drivers of current climate impacts all over the world, including, for example, freshwater supply for drinking and agriculture purposes, ecosystems, forestry, health, etc.. In this frame, to ensure temporal water availability in water-stressed areas, a sustainable groundwater management is an increasing challenge. Most of groundwater in the South-East Latium Region, Central Italy, as in the whole Apennine Mountains chain, is stored in karst aquifers. In this area important water resources are present, but even here in the last decades they are affected by groundwater depletion as a consequence of occurring drought events, the upward trend in the globally average temperature and the increasing of anthropogenic activities. Due to the lack of flow rates data of springs in many areas of Italy, the spring response modeling could be a useful tool for supporting a proper water resource management. Several research studies proposed methods based on relationships between spring discharges and rainfall data. The goal of this paper is to propose a model, based on rainfall-discharges cross correlations, in order to assess the spring flow rate patterns of Capodacqua di Spigno Spring, which is the main one in the study area. The results obtained using the developed model has been compared to an existing method that uses the SPI index for the estimation of the minimum annual spring discharge.

In many regions where drinking water supply is intermittent and unreliable, households adapt by storing water in cisterns or rooftop tanks. Both intermittent supply and stored water can be vulnerable to contamination by microorganisms with deleterious health effects. The Guadalajara Metropolitan Area is a rapidly growing urban center with over five million residents where household storage is nearly ubiquitous. This pilot study was conducted in July 2018 to examine the microbiological quality of drinking water in Guadalajara. Samples were tested for free available chlorine residual, total coliform bacteria, and E. coli. A survey on access to water and public perspectives was also conducted. Water exiting rooftop tanks exceeded regulatory limits for total coliform levels in half of the homes studied. Piped water arriving at two homes had total coliform levels that far exceeded regulatory limits. No E. coli were detected in any of the samples. Only 35% of homes had a chlorine residual between the recommended 0.2 and 1.5 mg/L. Many homes reported unpleasant odors and colors. Only 7% of residents drank the piped water. Future studies are needed, especially during April and May when many homes reported a higher disruption to water service.

Development of carbon nanomaterials for adsorption thus removal of organic pollutants from water is a progressive research subject. In this regard, carbon nanomaterials with bifunctionality towards polar and non-polar or even amphiphilic undesired materials is indeed attractive for further study and implementation. Here, we created carbon buckypaper adsorbents comprising amphiphilic (oxygenated amorphous carbon (a-COx)/graphite (G)) nanofilaments that can dynamically adsorb organic biomolecules (i.e. urease enzyme) and thus purify the wastewaters of relevant industries. Given the dynamic conditions of the test, the adsorbent was highly efficient in adsorption of the enzyme (88%) while permeable to water (2382 L.h-1.m-2), thus holds a great promise for further development and upscaling. A subsequent citric acid functionalization declined selectivity of the membrane to urease, implying the biomolecules adsorb mostly via graphitic domains rather than oxidized, polar amorphous carbon ones. The devised platform i.e. the urease functionalized buckypaper is optimally conductive (13 S.cm-1) and can be further employed as a biosensor. Accordingly, water treatment can be linked to biosensing via a nanostructured membrane.

Pollution of sub-surface water reservoirs mainly rivers and streams through contaminated water point sources (CWPS) was studied. The objective was to formulate a discrete time delay mathematical model which describes the dynamics of reservoir pollution using mixing-problem processes that involve single species contaminants such as nitrates, phosphorous and detergents. The concentration of pollutants was expressed as a function of the inflow and outflow rates using the principle for the conservation of mass. Systems of ODEs generated from principles of mixing problems were refined into a system of DDEs so that the concentration of pollutant leaving the reservoir at time would be determined at some earlier instant, for the delay. The formulated model is a mathematical discrete time delay model which would be used to describe the dynamics of sub-surface water reservoir pollution. The results from the validation of the model were analyzed to determine how time delays in the mixing processes affect the rate of particle movement in water reservoirs.

Elastic bodies entering the water might experience Fluid-Structure Interaction phenomena introduced by the mutual interaction between the structural deformation and the fluid motion. Cavity formation, often misleadingly named cavitation, is one of these. This work presents the results of an experimental investigation on the water entry of deformable wedges impacting a quiescent water surface with pure vertical velocity in free fall. The experimental campaign is conducted on flexible wedges parametrically varying the flexural stiffness, deadrise angle, and drop height. It is found that under given experimental conditions cavity pockets forms beneath the wedge. Their generation mechanism is found to be ruled by a differential between structural and fluid velocities, which is introduced by the structural vibrations. Results show that the impact force during water entry of stiff bodies is always opposing gravity, while in case of flexible bodies might temporarily reverse its direction, with the body that is being sucked into the water within the time frame between the cavity formation and its collapse. Severe impacts might also generate a series of cavity generation and collapses.

Degussa P25 is a benchmark form of TiO₂ used worldwide in photocatalysis studies. Currently no such benchmark exists for co-catalysts, which are essential for many photocatalytic reactions. Here, we present the preparation of Pt nanocluster co-catalysts on TiO₂ using an unmodified commercial source and equipment that is commonly available. Transmission electron microscopy reveals that the procedure produces TiO₂ decorated with Pt atom and nanoclusters (1-5 atoms). Optical reflectance and X-ray diffraction measurements show that the procedure does not affect the TiO₂ polymorph or UV-Vis absorbance. Gas phase photocatalytic splitting of heavy water (D₂O) shows that the Pt nanocluster decorated TiO₂ outperforms Pt nanoparticle (produced by photodeposition) decorated TiO₂ in D₂ production. Pt nanoclusters, produced directly from a commercial source, with high co-catalyst activity are prime candidates to be used in benchmark photocatalytic reactions.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

Industrial process control systems commonly exhibit features of time-varying, strong coupling, and strong nonlinearity. Obtaining accurate mathematical models of these nonlinear systems and achieving satisfactory control performance is still a challenging task. In this paper, data-driven modeling techniques and deep learning methods are used to accurately capture a category of smooth nonlinear system’s spatiotemporal features. The operating point of these systems may change over time, and their nonlinear characteristics can be locally linearized. We established the LSTM-CNN-ARX model by utilizing a fusion of long short-term memory (LSTM) network and convolutional neural network (CNN) to fit the coefficients of the state-dependent exogenous variable autoregressive (SD-ARX) model. Compared to other models, the hybrid LSTM-CNN-ARX model is more effective in capturing the nonlinear system’s spatiotemporal characteristics due to its incorporating the strengths of LSTM for learning temporal characteristics and CNN for capturing spatial characteristics. The model-based predictive control (MPC) strategy, namely LSTM-CNN-ARX-MPC, is developed by utilizing the model's local linear and global nonlinear features. The control comparison experiments conducted on a water tank system (WTS) show the effectiveness of the developed models and MPC methods.

Soybean a pulse of considerable nutritional value due to its high protein, fibers and polyunsaturated fatty acid (PUFA) contents, also contains phytoestrogenic compounds that definitely hinder its recommendation for general consumption. Contrarily to ancient times when soybeans were boiled, modern commercial soy-foods can contain up to 150 mg/100g of estrogenic isoflavones. Interestingly, current estimations of isoflavone intake in the literature do not distinguish between the origins of soy-food i.e. home-made or commercial. As a result, the isoflavone exposure in Asian countries may well be over-estimated. This study aims to demonstrate, based on step-by-step monitoring of isoflavones, that traditional and domestic treatments, leveraging isoflavones water-solubility, can indeed significantly reduce their content in soy-foods. Indeed, when compared to commercial foods, the isoflavone contents was found to be 20, 2.6, 4.5 and 9.8 times lower in “home-made” soy-juice, tofu, tempeh and miso, respectively. Additionally, water soaking was found to reduce the isoflavones levels in soy-textured-proteins by more than 70%. Hence, this simple process has the potential to help drastically reduce overall xenoestrogens exposure. This study could serve as a basis for establishing the isoflavones Reference Dose and issuing food safety guidelines.

Coastal marine ecosystems worldwide, like Florida Bay, are increasingly affected by tide alteration and anthropogenic disturbances which affect water quality imbalance leading to algal blooms. Increased bloom persistence is a serious threat due to the long-lasting impact on processes like carbon cycle and services like species presence. However, exploring eco-environmental feedback patterns of algal blooms remains challenging and poorly investigated, also due to the paucity of data. Florida Bay, taken as an epitome, has long experienced algal blooms in its central and western regions, and in 2006 an unprecedented bloom occurred in the eastern habitats. We analyzed the occurrence of blooms from three perspectives: (1) the spatial spreading networks of chlorophyll-a (CHLa) that pinpoints source and unbalanced habitats; (2) the fluctuations of water quality factors pre- and post-bloom outbreaks to in assess environmental impacts of ecological dysbiosis and target prevention and control of algal of blooms; and (3) the biogeochemical-spreading network topological co-evolution to quantify ecosystemic stability and ecological shift likelihood in long-term. Here, we propose Transfer Entropy (TE) to quantify dynamical interactions between spatial areas and biogeochemical factors (ecosystem connectome) underpinning bloom emergence and spreading, as well as environmental effects; the Pareto principle is defined for identifying the salient eco-environmental interactions of CHLa. We quantified the spatial dynamics of algal blooms, and thus obtained areas in need for ecological monitoring and potential bloom control. Results show that algal blooms are increasingly persistent over space with long-term negative effects on water quality factor. A dichotomy is reported between spatial ecological corridors of spreading and biogeochemical networks as well as divergence from the optimal eco-organization: randomization of the former due to nutrients' overload and temperature increase leads to scale-free CHLa spreading and extreme outbreaks a posteriori. Subsequently this increases bloom persistence, turbidity and salinity with potentially strong ecological effects on highly biodiverse and vulnerable areas such as tidal flats and marshes. Algal blooms are important ecosystem regulators of nutrient cycles; however, beyond limit chlorophyll-a outbreaks cause aquatic species mortality due to their effect on water turbidity, nutrient balance (nitrogen and phosphorus in particular), salinity and temperature. Beyond compromising local environmental quality, socio-ecological services are also compromised at large scales, yet ecological assessment models like the one presented are in need of application in subtropical and tropical bays worldwide.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

We enhanced the agro-hydrologic VegET model to include snow accumulation and melt processes and the separation of runoff into surface runoff and deep drainage. Driven by global weather datasets and parameterized by Land Surface Phenology (LSP), the enhanced VegET model was implemented in the cloud to simulate daily soil moisture (SM), actual evapotranspiration (ETa), and runoff (R) for the conterminous United States (CONUS) and the Greater Horn of Africa (GHA). Evaluation of the VegET model with independent data showed satisfactory performance, capturing the temporal variability of SM (Pearson correlation r: 0.22–0.97), snowpack (r: 0.86–0.88), ETa (r: 0.41–0.97), and spatial variability of R (r: 0.81–0.90). Absolute magnitudes showed some biases, indicating the need of calibrating the model for water budget analysis. The seasonal Landscape Water Requirement Satisfaction Index (L-WRSI) for CONUS and GHA showed realistic depictions of drought hazard extent and severity, indicating the usefulness of the L-WRSI for the convergence of evidence toolkit used by the Famine Early Warning System Network to monitor potential food insecurity conditions in different parts of the world. Using projected weather datasets and landcover-based LSP, the VegET model can be used not only for global monitoring of drought conditions, but also for evaluating scenarios on the effect of a changing climate and land cover on agriculture and water resources.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

A quasi-two-dimensional (quasi-2D) modelling approach is introduced to mimic transverse mixing of an inflow into a river from one of its banks, either an industrial outfall or a tributary. The concentrations of determinands in the inflow vary greatly from those in the river, leading to very long mixing lengths in the river downstream of the inflow location. Ideally, a two-dimensional (2D) model would be used on a small scale to capture the mixing of the two flow streams. However, for large-scale applications of several hundreds of kilometres of river length, such an approach demands too many computational resources and too much computational time, especially if the application will at some point require ensemble input from climate-change scenario data. However, a one-dimensional (1D) model with variables varying in the longitudinal flow direction but averaged across the cross-sections is too simple of an approach to capture the lateral mixing between different flow streams within the river. Hence, a quasi-2D method is proposed in which a simplified 1D solver is still applied but the discretisation of the model setup can be carried out in such a way as to enable a 2D representation of the model domain. The quasi-2D model setup also allows secondary channels and side lakes in floodplains to be incorporated into the discretisation. To show proof-of-concept, the approach has been tested on a stretch of the lower Athabasca River in Canada flowing through the oil sands region between Fort McMurray and Fort MacKay. A dye tracer and suspended sediments are the constituents modelled in this test case.

Hydrochemical and geophysical data collected during a hydrological survey in September 2017, reveal patterns of small-scale hydrological connectivity in a small water track catchment, north-European Arctic. Elevated tundra patches underlain by sands were disconnected from the stream and stored precipitation water from previous months. At the catchment surface and in the water track thalweg, some circular hollows, from 0.2 to 0.4 m in diameter, acted as evaporative basins with low d-excess values, from 2 to 4‰. Other hollows were connected to shallow subsurface runoff, yielding d-excess values between 12 and 14‰. ‘Connected’ hollows yielded a 50% higher dissolved organic carbon (DOC) content, 17.5±5.3 mg/L, than the ‘disconnected hollows, 11.8±1.7 mg/L. Permafrost distribution across the landscape is continuous, but highly variable. Open taliks exist under fens and small hummocky depressions, as revealed by electric resistivity tomography surveys. Isotopic evidence supports upward subpermafrost groundwater migration through open taliks under water tracks and fens/bogs/depressions, and its supply to streams via shallow sub-surface compartment. Temporal variability of isotopic composition and DOC in water track and a major river system, the Vorkuta R., evidence the widespread occurrence of the described processes in the large river basin. Water tracks effectively drain the tundra terrain and maintain xeric veg-etation over the elevated inter-track tundra patches.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

During the response of plants to adverse stresses, aquaporin (AQP) plays a prominent role in membrane water transport based on received upstream signals. In addition, they have various physical parts for dealing with environmental stresses. Due to the importance of the AQP gene family, studies have been conducted investigating the function and regulatory system of these genes. However, many of their molecular aspects are still unknown. This study aims to carry out a genomic-wide investigation of the AQP gene family in durum wheat using bioinformatics tools and to investigate the expression patterns of some members in response to salt stress. Our results showed that there are 80 TtAQP genes in durum wheat, which are classified into four main groups based on phylogenetic analysis. Many duplications were observed between the members of the TtAQP gene family, and high diversity in response to post-translational modifications was observed between TtAQP family members. The expression pattern of TtAQP genes disclosed that these genes are primarily upregulated in response to salt stress. Besides, qPCR data revealed that TtAQPs are more induced in delayed responses to salinity stress. Overall, our findings illustrate that TtAQP members are diverse in terms of their structure, regulatory systems and expression levels.

The present study aims to unravel the mechanisms of salicylic acid and rehydration and the physiological benefits in pepper plants grown under water deficit. 3x4 factorial scheme adopted, with three water regimes (irrigated, dry and rehydration) and four SA concentrations, namely: 0 (control), 0.5, 1 and 1.5 mM. Evaluated leaf moisture percentage, leaf water potential, chlorophylls (a and b), carotenoids, stomatal conductance, chlorophyll a fluorescence and H2O2 concentration at different times throughout the day and water conditions (irrigated, dry and rehydration) and SA applications (without the addition of the regulator (0) and with SA addition at concentrations equal to 0.5, 1 and 1.5 mM). Exogenous SA application favored stomatal conductance responses(gs) and modified fluorescence parameters (Fm, Fo, Fm', Fo', Fv/Fm, qP, ETR and NPQ) of sweet pepper plants subjected to drought followed by rehydration. SA concentration of 0.5 mM allowed a more expressive recovery of gs indices, effective quantum yield of photosystem II, with emphasis on excess energy (E) and maximum quantum yield (FV/FM) over time in plants subjected to drought and rehydration. We discovered that the use of SA, especially in association with rehydration, by modulating the variables gs and chlorophyll a fluorescence, prevents damage to membranes and consequently mitigates water deficit in pepper plants.

The phytoplankton community in 66 reservoirs ubicated at the hydrographic basin of the Ebro River (Spain) was analyzed. Samples were collected in the summer season during the period 2010-2015, with the main purpose of evaluate the Trophic State and Ecological Potential according to the Water Framework Directive of the European Union. In this work we presented a representative overview of several consecutive years of the state of the reservoirs and their associated trophic status; methodology was to obtain statistically significant relationships between the phytoplankton community and main physicochemical water quality variables (water transparency, pH, chlorophyll a, total and soluble phosphorus, anoxic zone depth, nitrite, nitrate and ammonium concentrations). We provide data for retrospective comparative of the state of the reservoirs with previous and current studies in order to improve the management of these reservoirs, and to serve as data reference for future works in a context of global change (climate and pollution).

Saudi Arabia consists mainly of desert land. However, it has big and small natural wetlands and artificial wetlands. Most of these wetlands are seen along the Red Sea and the Arabian Gulf coastal regions. Al-Asfar Lake, located in the Eastern Region of Saudi Arabia, is one of the historical landmarks of Al-Ahsa province. The primary lake water source is agricultural drainage water, which some refer to as an artificial lake. This paper mainly aims to reflect shade on the wetlands in Saudi Arabia in general and to show in detail the environmental impacts of Al-Asfar Lake on the ecosystem and biodiversity of the study area. The analytical review of the previous studies conducted in Al-Asfar Lake was adopted in this article. Hence, the impact of the lake on the land-use system, water quality and biodiversity was illustrated as the main outputs of the review analysis. However, the sustainable management of Al-Asfar Lake requires the stakeholders to adopt the wetland ecosystem health concept, which might lead to improving the lake's environmental conditions.

Oil-water separation using special wettability materials has received much attention due to its low energy consumption and high separation efficiency. Herein, a fluorine-free superhydrophobic cotton fabric(PDMS/STA -coated cotton fabric) was successfully prepared by a simple impregnation method using hydroxyl-capped polydimethylsiloxane (PDMS-OH), tetraethoxysilane (TEOS) and stearic acid (STA) as precursors. The Investigation found that the cross-linking reactions between the hydroxyl groups form PDMS-OH, hydrolyzed TEOS made a strong interact of PDMS-OH and cotton fabric. Besides, a suitable roughness surface of coated cotton fabric was established by introducing STA due to its long chain-structure. The contact angle of this composite can reach 158.7°under optical condition due to its low surface energy and desired roughness. The oil/water separation efficiency of PDMS/STA-coated cotton fabric is higher than 90% even after 10 cycles of oil-water separation, the oil flux can reach 11862.42 L m-2 h-1. In addition, PDMS/STA-coated cotton fabric exhibits excellent chemical stability and durability under extreme conditions such as strong acid (HCl, pH=1~2) and alkali (NaOH, pH=13~14), the hydrophobicity of PDMS/STA-coated cotton fabric was decreased to 147° even after 350 cycles of abrasion testing.

Rotary tillage is a main management tillage practices and widely applied in the North China Plain. However, the long term rotary tillage (depth of 20 cm) results in soil compaction and plow pan formation, which reduces water use efficiency and nutrient uptake, and then impedes the yield increase. In this study, a 3-year field experiment was conducted to investigate the influence of different depths of tillage on soil bulk density, field capacity, water use, photosynthetic rate, nutrients and maize yields in the North China Plain. Three depths of tillage (D20, depth of 20 cm; D25, depth of 25 cm; D30, depth of 30 cm) were assessed. D25 and D30 significantly reduced soil bulk density and improved field capacity in 10-20 and 20-30 cm soil layer, compared to D20. Soil water consumption for D25 was significantly higher 10.12% and 6.61% than that for D20 and D30, respectively. Photosynthetic rate for D25 significantly improved than that for D20 and D30. Total nitrogen in 0-20cm soil layer decreased with the depths of tillage. The maize yields for D25 significantly increased by 20.92% and 21.56% compared to that for D20 and D30, respectively. Structural equation models showed that the total effects of tillage, total nitrogen, photosynthesis and soil water consumption on yields were 0.019, -0.628, 0.121, and 0.895 (path coefficients λ), respectively. The results demonstrated that D25 could improve maize yields, water use efficiency, photosynthetic rate by improving soil water consumption. Depth of 25 cm is optimal tillage practice for the maize production in the North China Plain.

Ethiopia has decades of experience in implementing land and water management interventions. Nonetheless, there remains persisting challenges to follow an adaptive management (AM) approach in efforts of restoring and transforming agricultural landscapes. This review was carried out to synthesize evidences on the impact on agricultural landscapes following the implementation of land and water management practices and to evaluate the use of AM approaches. We explored how elements of the structures and functions of landscapes have been transformed, and how the components of AM, such as structured decision-making and learning processes, have been applied. Despite numerous environmental and economic benefits of land and water management interventions in Ethiopia, this review revealed gaps in AM approaches. These include: (i) insufficient efforts in relation to evidence based contextualization of interventions, (ii) insufficient efforts in monitoring of bio-physical and socio-economic processes and changes post implementation, (iii) lack of trade-off analyses, and (iv) inadequacy of local community engagement and provision of feedback. Given the many uncertainties we must deal with, efforts to restore and transform agricultural landscapes cannot follow a business-as-usual approach. Future investment, in AM approach, tailored to the needs and context would help to achieve the goals of sustainable agricultural landscape transformation. The success depends on three interdependent pillars of action: the ability to make a robust, co-developed plan of interventions, the ability to continuously monitor changes based on key variables, and to learn from the knowledge generated and apply the learning as implementation evolves.

Both academic literature and global organizations have emphasized the need for responsible water consumption, as stated in the Sustainable Development Goal 12. However, individuals’ water-saving behaviors in their current state are not enough. This situation entails a resistance to change (RC) in consumer habits and a lack of perceived risk of scarcity. The novelty of this study lies in examining the influence of RC (through its emotional, cognitive, and confidence components) and perceived risk on water-saving intention. Interviews (n = 384) were conducted in the southeast Mediterranean area of Spain by interviewers using a paper-and-pencil questionnaire. The results of the structural equation modeling show that the perceived risk and the components of cognitive rigidity and negative emotions exert a direct influence on water-saving habits and an indirect influence on water-saving intention. None of the components of RC directly influence intention, and a lack of confidence in the outcomes of water saving does not influence water-saving habits or water-saving intention. In addition to the results obtained, the novelty of the work lies in the idea that in order to influence the perception of the risk of water scarcity through awareness campaigns, it is better to use an emotional message rather than showing facts or information, because this does not drive water saving behavior.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

The environmental vulnerability diagnosis of a river basin depends on a holistic analysis of its environmental aspects and degradation factors. Based on this diagnosis, the definition of priority areas where interventions for environmental recovery should be carried out is fundamental, since financial and natural resources are limited. In this study, we developed a methodology to assess these fragilities using an Environmental Vulnerability Index (EVI) that combines physical and environmental indicators related to the natural sensitivity of ecosystems and their exposure to anthropogenic factors. The EVI developed was applied to the headwater’s region of the São Francisco River basin, Brazil. The proposed index was based on the AHP multi-criteria analysis and was adapted to include four variables representative of the study area: Land Use Adequacy, Burned Area, Erosion Susceptibility and Quantitative Water Balance. The EVI analysis highlighted that the presence of easily erodible soils, associated with sloping areas and land uses above their capacity, generate the most vulnerable areas in the headwaters of the São Francisco River basin. The results of this study indicate where resources should be applied for environmental preservation in the basin under study, directing the allocation of efforts to areas with lower resilience in maintaining ecosystem services.

The effects of acidic electrolyzed water (AEW) on the microbiological and physicochemical properties of fresh-cut red cabbages were studied. The fresh-cut red cabbages and artificially inoculated red cabbages with Salmonella Typhimurium DT104 were washed with distilled water (DW) and different available chlorine concentration (ACC) of AEW for different times. AEW treatments significantly reduced the populations of native aerobic bacteria, molds and yeasts, and artificially inoculated S. Typhimurium DT104 compared to the DW treated and untreated red cabbage samples. The effectiveness of AEW treatments was greatly enhanced with increasing ACC and treatment times. S. Typhimurium DT104 were not detected in the washing water after the red cabbages treated by AEW. The surface color, pH, and total phenolic contents were did not significantly change when the red cabbages were washed with DW and 100 ppm AEW for 3 min. The anthocyanin contents and antioxidant activities of red cabbage were significantly reduced by 18.5% for cyanidin, 22.1% for pelargonidin, and 11.2% for DPPH radical scavenging activity, the impacts on the nutritional benefits of red cabbage were considered as limited and acceptable. The optimal process condition of AEW for washing red cabbage was 100 ppm for 3 min. In these conditions, most of the native microflora were inactivated, and artificial inoculated S. Typhimurium DT104 on the red cabbage were reduced by 40.2% (3.67 log CFU/g) and with minimal losses of nutrients and antioxidant activity, as well as no requirement of discontinuation treatment on the washing water.

This research focuses on monitoring the spatiotemporal changes of urban surface water in Dhaka City from 1990 to 2021, utilizing satellite imagery and the Google Earth Engine (GEE) platform. Surface water is essential for urban, environmental, and agricultural ecosystems, and its dynamics have significant implications for water resource planning and environmental management. The main objectives of this study are to assess the extent of urban surface water coverage over the last three decades and identify trends of water loss or gain in the study area. The study employs Landsat 5 TM and Landsat 8 OLI/TIRS imagery, integrating GEE with machine learning coding and WRI techniques to extract and analyze surface water data efficiently. Traditional remote sensing methods for dynamic monitoring are time-consuming and cumbersome, but GEE offers a user-friendly and accurate approach, providing easy access to satellite data and cloud-based processing. The results reveal a concerning trend in urban surface water coverage, indicating a significant reduction from 36.23 km² in 1990 to 5.83 km² in 2021, representing a loss of approximately 20 square kilometers or 45 percent of surface water over the last three decades. The decline is attributed to factors such as unplanned urban expansion, rapid real estate development, and increased industrial and economic activities in the study area. The developed algorithms utilizing GEE offer valuable insights into the maximum and minimum extent of surface water, enabling effective surface water planning and management. These findings contribute to sustainable water resource management and environmental preservation in Dhaka City.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

This study inscribes itself in the global discussion on the nurturing of pro-environmental behaviors among young people for a sustainable future. Here we focus on students' interest in Ecosystem Services and Sustainability to explain their awareness and optimism about the environmental issues of air pollution, water shortage and green gas emission in 50 countries around the world. To this end, we use the cross-sectional survey data of the OECD's Program for International Student Assessment (PISA) 2015, along with seemingly unrelated bi-variate weighted ordered Probit modeling with country specific effects. The results show that in addition to factors such as age, gender, immigration status, and economic, social and cultural status, interest in the biosphere is a significant determinant of students' environmental awareness and optimism. In fact, a one level increase in students' interest in ecosystem services and sustainability raises on average their awareness level by 15.3% for the issue of air pollution, 15.7% for the issue of water shortage, and 24.6% for the issue of green gas emission. Although students' interest in the biosphere seems to not have a significant effect on their expectations about the issue of green gas emission, it does however raise their level of optimism by 0.8% for the issue of air pollution, and 0.2% for the issue of water shortage. Furthermore, every one level increase in students' environmental awareness leads to 17.3% more optimism about the issue of air pollution, 15.8% more optimism about the issue of water shortage, and 17.4% more optimism about the issue of green gas emission. Therefore, relying on the Theory of Planned Behavior (TPB), our results imply that governments and policy makers can successfully leverage young people interests in the biosphere to effectively achieve their goals for sustainability.

Urban rivers and waterfronts play a vital role in the ecological, social, and economic fabric of cities, providing not only aesthetic value but also serving as important ecosystems that contribute to the overall well-being of urban environments. However, many urban rivers, including the Beirut River in Lebanon, face challenges such as pollution, neglect, and the loss of recreational and ecological value due to urbanization and industrialization. According to the Lebanese MOE (Ministry of Environment), almost 70% of Lebanese rivers are polluted due to untreated waste management systems and which leads to undrinkable water and possible flooding disasters if not treated. This study addresses the problem of abandoned and degraded spaces along the Beirut River riverside through the application of urban acupuncture, a strategic approach that targets specific points in the urban environment to stimulate positive change and regeneration. The aim of the study is to assess the effectiveness of implementing small-scale ‘sensitive urban points’ known as urban acupuncture as the method for regenerating the Beirut River riverside, with the hypothesis that targeted interventions through Blue Urban Acupuncture or Aqua-puncture- can lead to significant improvements in the ecological, social, and economic aspects of the area that re-connect the people of Beirut with its river. The methodology involves a multidisciplinary approach that integrates urban design, and community engagement, and analysing similar examples of different approaches through creating a comparative table. Data collection includes environmental assessments of water quality, biodiversity, and ecosystem health, as well as social surveys to understand community needs and perceptions. By applying urban acupuncture principles to the Beirut River riverside, this study seeks to demonstrate how strategic interventions can lead to the regeneration of abandoned spaces, improve the overall quality of the urban environment, and create sustainable and inclusive riverside landscapes that benefit both the environment and the community.

This study investigates the impact of water stress on grapevines, specifically examining the role of rootstocks and aquaporins. Two experiments on potted plants were conducted in central Chile during the summer, under conditions of high water demand, involving various rootstock genotypes and combinations of Cabernet Sauvignon (CS) grafted onto rootstocks. Significant differences were observed among plants in terms of stem water potential, stomatal conductance, and growth rate. Notably, the CS/CS combination consistently displayed the slowest growth rate, regardless of the irrigation treatment. The study also analyzed the expression levels of plasma membrane intrinsic proteins (PIPs) and tonoplast intrinsic proteins (TIPs) aquaporins in the leaves of grafted plants. Specifically, VvPIP2;2 aquaporins showed reduced expression after 14 days without irrigation, whereas VvTIP1;1 and VvTIP2;1 expression levels correlated positively with gs responses in grafted plants, suggesting their role in modulating water content in leaves under water stress. TIP aquaporins likely play a significant role in the differential responses of CS plants towards nearly isohydric or anisohydric behaviour. The CS/CS combination exhibited near isohydric behavior, correlating with lower TIP aquaporin expression, while the combination of CS onto 1103P and 101-14 showed higher expression, indicating anisohydric behavior. The findings suggest that grafted plants are more resilient to water stress, supporting the idea that rootstocks can mitigate the effects of water stress on the scion.

Oleogels are of high interest as promising substitutes for trans fats in foods. An emulsion-templated method was used to trap olive oil in the chitosan crosslinked with vanillin matrix. Oil in water emulsions (50:50 w/w) with different chitosan content (0.7 and 0.8% w/w) with constant vanillin/chitosan ratio (1.3) were air-dried at different temperatures (50, 60, 70 and 80ºC) and freeze-dried (-26ºC and 0.1 mbar) to produce oleogels. Only falling-rate periods were determined during air-drying kinetics and were successfully modelled with empirical and diffusional models. At drying temperature of 70ºC the drying kinetics were the fastest. Viscoelasticity of oleogels showed that elastic modulus significantly increased after drying at 60 and 70ºC, and those dried at 50ºC and freeze-dried were weaker. All oleogels showed high oil binding capacity (&gt; 91%), but the highest values (&gt; 97%) were obtained in oleogels with a threshold elastic modulus (50,000 Pa). Oleogels color depended on drying temperature and chitosan content (independent of the drying method). Significant differences were observed between air-dried and freeze-dried oleogels with respect to oxidative stability. Oxidation increased with air drying time regardless of chitosan content. Found results indicated that drying conditions must be carefully selected to produce oleogels with specific features.

Researches are moving to iron and ammonia elimination from ground water. Here, we are using poly acrylic–poly acrylamide hydrogel which grafted with 3-chloroaniline. This copolymer was synthesized by addition polymerization. Effect of agitation time, dosage and adsorbents temperature on the removal process sensitivity has been investigated. The copolymer was described experientially and theoretically. Isothermal, kinetic adsorption models and were discussed. This hydrogel could be regenerated efficiently (98.3%removal of iron and 100% removal of ammonia). Density functional theory DFT method using B3LYP/6-311G(d,p),LANL2DZ level of the theory were managed to investigate stationary states of grafted co-polymer and the complexation energy of the hydrogel with the studied cations. NBO analysis is using DFT to investigate the negative centers on the hydrogel. The complexation energy showed selectively of hydrogel to studied cations.

Seasonal snowpacks, characterized by their snow water equivalent (SWE), play a major role in the hydrological cycle, snow melt contributions to floods and the subsequent availability of water resources downstream. Accurately estimating SWE and understanding its spatial and temporal variations presents a considerable challenge, particularly within mountainous regions characterized by complex terrain and limited observational data. Seeking to enhance the performance of the widely used Soil and Water Assessment Tool (SWAT), we report a new approach characterising snowpack behaviour incorporating both modelled and remotely sensed derived SWE calibration data. We focus on the Chenab River Basin (CRB) a headwater catchment of the Indus Basin, globally significant in terms of human inhabitants and intensifying flood risk due to climate change. We conducted a thorough assessment of five satellite-derived and reanalysis-based precipitation datasets: ERA5-Land, CMORPH, TRMM, APHRODITE, and CPC UPP. This reveals significant levels of uncertainty in global precipitation products when compared to reference data from observed stations as well as in the resulting simulated streamflow from the SWAT model. Subsequently, we expanded the scope of the SWAT model to encompass the spatial and temporal simulation of SWE. This was achieved by incorporating information from remotely sensed and modelled SWE products, manually adjusting snow parameters in R-SWAT for both the main basin and at sub-basin scales. Integrating SWE from reference snow products into the calibration process, alongside streamflow data, substantially enhanced modelling accuracy to simulate SWE compared to the conventional auto-calibration and single-variable approaches reliant solely on streamflow data. This approach results in considerable improvement in SWE predictions and to some extent in streamflow simulation in catchments dominated by snow. This research highlights the potential of remote sensing and modelled SWE parameterisation in the absence of in-situ snowpack data in high-altitude environments. An improved understanding of SWE behaviour is vital for predicting hydrological responses spanning hazards to water resources in the populous downstream regions of the Indus Basin, especially in the face of climate change.

Africa’s water needs are often supported by eutrophic waterbodies dominated by cyanobacteria posing health threats to riparian populations from cyanotoxins, and Lake Victoria is no exception. In two embayments of the lake (Murchison Bay and Napoleon Gulf), cyanobacterial surveys were conducted to characterize the dynamics of cyanotoxins in lake water and water treatment plants. Forty-six cyanobacterial taxa were recorded and out of these 14 were considered potentially toxigenic (i.e., from the genera Dolichospermum, Microcystis, Oscillatoria, Pseudanabaena and Raphidiopsis). A higher concentration (ranging from 5-10 µg MC-LR equiv. L-1) of microcystins (MCs) was detected in Murchison Bay compared to Napoleon Gulf, with a declining gradient from the inshore (max. 15 µg MC-LR equiv. L-1) to the open lake. In Murchison Bay, an increase either in Microcystis sp. biovolume and MC was observed over the last two decades. Despite high cell densities of toxigenic Microcystis and high MC concentrations, the water treatment plant in Murchison Bay efficiently removed the cyanobacterial biomass, intracellular and dissolved MC to below the lifetime guideline value for exposure via drinking water (&lt; 1.0 µg MC-LR equiv. L-1). Thus, the potential health threats stem from the consumption of untreated water and recreational activities, along the shores of the lake embayments. MC concentrations were predicted from Microcystis cell numbers regulated by environmental factors such as solar radiation, wind speed in the N-S direction and turbidity. Thus, an early warning through microscopical counting of Microcystis cell numbers is proposed to better manage health risks from toxigenic cyanobacteria in Lake Victoria.

Uniform water soluble MoS2 quantum dots (WS-MSQDs) are synthesized via a sequential combination of sintering/etching/exfoliation method and solvothermal route. The obtained WS-MSQDs with average size of approximately 3.4 nm exhibit sufficient water solubility and remarkable fluorescence properties. The WS-MSQDs have been utilized as a probe for detection of Fe3+ ions with high selectivity and specificity. Furthermore, the WS-MSQDs exhibit high fluorescence stability under different conditions. Finally, the WS-MSQDs are successfully applied for the fluorescence imaging of Fe3+ in living cells, which exhibited practical potential for biomedical applications.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

Stipa tenacissima (S. tenacissima), or esparto, is a perennial tussock grass that coexists with Pinus halepensis (P. halepensis) in semi-arid mediterranean woodlands. This research was carried out to explore diurnal transpiration at leaf level in esparto grass under different levels of pine-esparto competition and in contrasting environmental conditions of soil water. The measurements were spanned from the summer 2020 to spring 2021. The relationship between transpiration and competence was conducted in open and closed P. halepensis stands and taken into account the type of leave (green, senescent) and the maturity of the esparto grass. We observed a higher control of transpiration in green leaves, and correlations between transpiration and soil water were noted exclusively in this type of leaf. Our results substantiated a significant impact of pine competitors on transpiration of esparto grass, particularly during seasons characterized by high water-demand scenarios: the summer drought period and the commencement of the growing and flowering period (spring). Furthermore, our findings confirmed a greater response to transpiration in mature bushes compared to young ones under severe water stress, denoting higher adaptation to drought as esparto ages. Our results may have important implications for the dynamics and management of these semi-arid mixed woodlands, as well as the planning of reforestation programs aimed at restoring esparto grass steppes.

The construction of 22 dams on the Euphrates has reduced the flow of this river, changed the hydrology and destroyed the ecosystem. In order to understand the effect of extreme management on water, 4 coastal points from the Euphrates catchment area were selected to investigate the dynamics of the water level. Using the Cadmium method, the radius of each point was calculated to be 140 meters to study the NDWI index and satellite monitoring. 546 Landsat 8 OLI/TIRS satellite images from 2013 to 2022 were used. The analysis showed that the water level of the Euphrates in the fourth coordinate is directly related to the data of the first and third coordinates and the dynamics of the water level in the fourth coordinate is 3.6 to 4.2 percent of the first coordinate and another 5.2 to 5.9 percent is affected by the third coordinate. Is. Also, the data from August 2013 to 2022 were analyzed. The results showed that the correlation coefficients of the data related to the first coordinates are related to the third and fourth coordinates. It was proved that fluctuations in the first coordinate led to 27% change in the third coordinate in the months of August. Also, the changes in the first point caused 18-19.8% change in the dynamic level of water in the fourth point, and 22.5% of the changes in the water level in the fourth coordinate were affected by the third point.

Hydrologic studies on rainfall-runoff have been extensively conducted in many regions around the globe to fulfill various desirable needs with a purpose of effective and proper planning and managing water resources for present and future uses, whereas such study is not well drawn much attention to river catchments of Tonle Sap Lake Basin in Cambodia, which may prevail to water insecurity. The Stung Sreng catchment, which is one among them considered to be a significant basin for water resources management in Cambodia, is remarkably increasing under intolerable pressures in water resources development. This study was to apply HEC-HMS (Hydrological Engineering Center-Hydrological Model System) model to predict streamflow of Stung Sangker catchment, located in Tonlesap Lake Basin in Cambodia. The result showed that the calibration was good at monthly basis. The model performance was given by Nash-Sutcliffe Efficiency criteria followed by 0.44 for daily and 0.71 for monthly basis, respectively. Moreover, the Percent Bias (PBIAS) for daily and monthly simulation was 4.13% and 3.56%, indicating a satisfactory model fit. The HEC-HMS conceptual model can be used to simulate flow of Stung Sangke catchment on a continuous time scale particularly monthly basis. The result also indicated that there was a clear seasonal variation in monthly water availability, especially during both wet and dry season.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.

Abstract: Agarose is known to form a homogeneous thermoreversible gel in aqueous medium over a critical polymer concentration. The solid-liquid phase transitions are thermoreversible but depend on the molecular structure of the agarose sample tested. Then, in a first step, the structure was characterised by 1H and 13C NMR in D2O and in DMSO which is a solvent of agarose whatever the temperature. A low yield in methyl substituent on the D-galactose unit was determined. Then, evolution of the 1H NMR spectrum was followed as a function of temperature in increasing and decreasing temperature process from 25 to 80°C. A large thermal hysteresis is obtained and discussed. It helps to interpret rheological behaviour. In fact, NMR signals are related to proton relaxation and especially to proton involved in H-bonds between water and -OH agarose for tightly bound water and agarose/agarose in chain packing. In a second step, water was exchanged against ethanol which is a non solvent of agarose. A stable gel was demonstrated and characterised by rheology to be compared with aqueous behaviour. Bound water playing the role of plasticizer is probably removed and the gel is much stronger (and brittle) in ethanol with a larger thermal stability. It is the first time that such gel is characterised without phase transition when passing from a good-solvent to a non-solvent. This extends the domains of application of agarose.

The Yamuna River in Delhi is a prevalent epitome of the depleted ecosystem that has transformed into a sewage drain due to intense pollution and blooming anthropogenic pressure. As a leading polluter, Delhi contributes to more than 70% of Yamuna's pollution load. Its drains discharge a massive B.O.D. load daily into the river, making it severely polluted, as reflected by the water quality index. The paper uses secondary data to analyze the parameters to determine the water quality of Yamuna at different monitoring sites. It performs correlation analysis to determine the relationship among factors contributing to river water pollution. The results of correlation analysis suggest a highly significant association between parameters COD-BOD, but the association is mild to a minimum among other parameters such as BOD-DO, BOD-pH, COD-DO, COD-pH and DO-pH. Most parameters were observed to be above the hazardous level acceptable for using river water. The analysis of S.T.P.s indicates the need to increase the capacity in terms of treatment, storage, reopening of closed plants and efficient operation to meet the increasing demand for fresh Water. Also, there is a need to create demand for wastewater in different sectors of urban areas like construction, horticulture, industrial coolants, etc.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

In this study, a new approach for estimating volume variations of lakes and reservoirs using water levels from satellite altimetry and surface areas from optical imagery is presented. Both input data sets, namely water level time series and surface area time series, are provided by DGFI-TUM‘s Database of Hydrological Time Series of Inland Waters (DAHITI). The approach is divided into three parts. In the first part, a hypsometry model based on the new modified Strahler approach is computed by combining water levels and surface areas. The hypsometry model describes the dependency between water levels and surface areas of lakes and reservoirs. In the second part, a bathymetry between minimum and maximum surface area is computed. For this purpose, DAHITI land-water masks are stacked using water levels derived from the hypsometry model. Finally, water levels and surface areas are intersected with the bathymetry to estimate a time series of volume variations in relation to the minimum observed surface area. The results are validated with volume time series derived from in-situ water levels in combination with bathymetric surveys. In this study, 28 lakes and reservoirs located in Texas are investigated. The absolute volumes of the investigated lakes and reservoirs vary between 0.099 km³ and 6.448 km³. The correlation coefficients of the resulting volume variation time series with validation data vary between 0.80 and 0.99. Overall, the relative errors with respect to volume variations vary between 2.8% and 14.9% with an average of 8.3% for all 28 investigated lakes and reservoirs. When comparing the resulting RMSE with absolute volumes, the absolute errors vary between 1.5% and 6.4% with an average of 3.1%. This study shows that volume variations can be calculated with a high accuracy which depends essentially on the quality of the used water levels and surface areas. In addition, this study provides a hypsometry model, high-resolution bathymetry and water level time series derived from surface areas based on the hypsometry model. All data sets are publicly available on the Database of Hydrological Time Series of Inland Waters (DAHITI, https://dahiti.dgfi.tum.de).