Efficient thermal management of modern electronics requires the use of thin films with highly anisotropic thermal conductivity. Such films enable the effective dissipation of excess heat along one direction while simultaneously providing thermal insulation along the perpendicular direction. In this study, we investigate the thermal conductivity of bilayer graphene (BLG) sheets using non-equilibrium molecular dynamics, examining both in-plane and cross-plane thermal conductivities. The in-plane thermal conductivity of 10 nm × 10 nm BLG with zigzag and armchair edges at room temperature is found to be around 204 W/m.K and 124 W/m.K, respectively. The in-plane thermal conductivity of BLG increases with sheet length. For all sizes, BLG with a zigzag edge exhibits higher thermal conductivity than that of the armchair edge, with this difference becoming more pronounced as the lengths of the sheets increase. In addition, increasing temperature from 300 K to 600 K decreases the in-plane thermal conductivity of a 10 nm× 10 nm zigzag BLG by about 34%. Similarly, the application of a 12.5% tensile strain induces a 51% reduction in its thermal conductivity compared to the strain-free values. Armchair configurations exhibit similar responses to variations in temperature and strain, but with less sensitivity. Furthermore, the cross-plane thermal conductivity of BLG at 300 K is estimated to be 0.05 W/m·K, significantly lower than the in-plane results by approximately four orders of magnitude. The cross-plane thermal conductance of BLG decreases with increasing temperatures, specifically, at 600 K, its value is almost 16% of that observed at 300 K.

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

In-plane electro-optical switching (IPS) is a natural feature of a conventional planar aligned display cell based on deformed helix ferroelectric liquid crystal effect (DHFLC-effect) with sub-wavelength helix pitch if the tilt angle close to 40 degrees.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

In this letter, a century-old problem is studied; namely, to find a unified analytic description of the non-uniform distribution of mean velocity across the entire domain of turbulent flow for all Reynolds numbers within the framework of the Prandtl mixing length theory. Considering the Prandtl mixing length model, a closed form solution of the mean velocity profile of plane turbulent flow is obtained. The profiles of several useful quantities are given, such as turbulent viscosity, Reynolds turbulent stress, Kolmogorov's scaling law, and energy dissipation density. It is shown that the energy dissipation density at the surface is finite, whereas Landau's energy dissipation density is infinite. The closed form solution reveals that the universality of the turbulent velocity logarithmic profile no longer holds, but the von K\'arm\'an constant is still universal. The closed form solution is validated by both direct numerical simulation and experiments. The studies confirm that the van Driest mixing length theory is suitable for smooth walls, and the Prandtl mixing length theory is suitable for rough walls. Furthermore, a new formulation of the resistance coefficient of turbulent flow in pipes is given in implicit form.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

This paper investigates the classical but yet intriguing question of modeling orthotropic RC floor systems endowed with lightening elements, by means of a uniform orthotropic slab, in order to describe accurately the building response under seismic loads. The simplified method, commonly adopted by engineers, based on the equivalence between the transverse stiffness of the RC elements of the real floor and those of the orthotropic slab is presented. A case study in which this simplified method is used is also provided. Then, an advanced finite elements (FE) based method to determine the elastic properties of the equivalent homogenized orthotropic slab is proposed. Based on the results obtained from the application of this method to a case study, a discussion on the adequacy of the simplified method is also provided.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

Confined masonry (CM) is a construction system which consists of masonry wall panels enclosed by vertical and horizontal reinforced concrete confining elements. The presence of these confining elements distinguishes CM from unreinforced masonry system and makes this technology suitable for construction of structures in regions subjected to intense seismic or wind actions. CM construction has been used in many countries and regions, and has performed well in past earthquakes. The purpose of the paper is to review past research studies related to the seismic in-plane and out-of-plane behaviour of CM structures. The authors have identified the key design and construction parameters which were considered in past research studies and have performed statistical analyses to establish their influence on the seismic performance of CM buildings. For the purpose of this study the authors have compiled databases of previous experimental studies on CM wall specimens which were used for statistical analyses. Finally, the paper discusses research gaps and needs for future research studies which would contribute to the understanding of seismic behaviour and failure mechanisms of CM walls.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

With the increased use of simulation based training using animal models for the education of surgical and anaesthetic techniques, an increased understanding of the anatomy of such models and how they compare to humans is required. The transversus abdominis plane block is a regional anaesthetic technique that requires an understanding of the abdominal wall anatomy along with proficient ultrasound use. The current review aims to compare the anatomy of the abdominal wall across species, particularly focussing on the pertinent differences within the class of mammals, and secondarily, it aims to address the implications of these differences for simulation based training of the transversus abdominis plane block. To achieve this, the PubMed, Web of Science and Google Scholar databases were searched for relevant literature. The mammalian abdominal wall differs in its musculature, vasculature or innervation from that of amphibians, birds or reptiles, however, among species of mammals, the structure of the abdominal wall follows a similar framework. Particular differences among mammals include the additional muscular layer of the panniculus carnosus found in most mammals other than humans, the variable arterial origins and dominant vascular supply of the abdominal wall and the number of thoracolumbar nerves innervating the abdominal wall. When using animal models for simulation based training, the pig is recommended for the transversus abdominis plane block given its closely homologous abdominal wall structure, availability and larger comparative size.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

Victor Vasarely’s (1906-1997) important legacy to the study of human perception is brought to the forefront and discussed. A large part of his impressive work conveys the appearance of striking three-dimensional shapes and structures in a large-scale pictorial plane. Current perception science explains such effects by invoking brain mechanisms for the processing of monocular (2D) depth cues. Here in this study, we illustrate and explain the local effects of 2D color and contrast cues on the perceptual organization in terms of figure-ground assignments, i.e. which local surfaces are likely to be seen as “nearer” or “bigger” in the image plane. Paired configurations are embedded in a larger, structurally ambivalent pictorial context inspired by some of Vasarely’s creations. The figure-ground effects these configurations produce reveal a significant correlation between perceptual solutions for “nearer” and “bigger” when no other monocular depth cues are given in the image. In consistency with previous findings on similar, albeit simpler visual displays, a specific color may compete with luminance contrast in resolving the planar ambiguity of a complex pattern context. Vasarely intuitively understood, and successfully exploited, this kind of subtle context effect in his art, well before empirical investigations had set out to study and explain their genesis in terms of information processing by the visual brain.

As is well known, the main contribution of the FRP strips to the strength of load-bearing walls is an improvement in the in-plane strength. This paper deals with the possibility of applying the FRP strips in way to modify the strengthening mechanism of the FRP reinforcing system, from an in-plane to an out-of-plane strengthening mechanism. In order to achieve this goal, a second reinforcement system – derived from the CAM system (Active Confinement of Masonry) – provides connections between the FRP strips placed on the opposite sides of the wall. This new strengthening technique – called the straps/strips technique – establishes a stiffness constraint that forces the opposing FRP strips to behave like two flanges of an FRP I-beam embedded in the wall. Consequently, the use of FRP strips also improves the flexural strength of the wall. The present paper briefly summarizes the results obtained in previous works with the straps/strips technique and proposes an improvement of this strengthening technique, based on some weak-points emerged in the early experimentations. The paper also shows the results of a further experimental test, performed with the improved straps/strips technique. Finally, the similarity between FRP strips with transversal connection and concrete wythes of a sandwich panel with flexible connectors leads to interpret the behavior of the ideal I-beam in terms of composite action established between the FRP strips. This paves the way for analytical modeling of the straps/strips technique.

Up to 56% of patients develop chronic postsurgical pain (CPSP) after coronary artery bypass grafting (CABG). CPSP can affect patients’ moods and decrease daily activities. The primary aim of this study was to investigate CPSP severity in patients following off-pump (OP)-CABG using the Neuropathic Pain Symptom Inventory (NPSI). This was a prospective cohort study conducted in a cardiac surgery department of a teaching hospital. Patients undergoing OP-CABG were enrolled in an erector spinae plane block (ESPB) group (n = 27) or a control (CON) group (n = 24). Before the induction of general anesthesia, ESPB was performed on both sides under ultrasound guidance using 0.375% ropivacaine. The secondary outcomes included cumulative oxycodone consumption, acute pain intensity, mechanical ventilation time, hospital length of stay, and postoperative complications. CPSP intensity was lower in the ESPB group than in the CON group 1, 3, and 6 months postsurgery (p < 0.001). Significant between-group differences were also observed in other outcomes, including postoperative pain severity, opioid consumption, mechanical ventilation time, and hospital length of stay in favor of the ESPB group. Preemptive ESPB appears to decrease the risk of CPSP development in patients undergoing OP-CABG. Reduced acute pain severity and shorter mechanical ventilation times and hospital stays should improve patients’ satisfaction and reduce perioperative complications.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

Weaving is an ancient and effective structural forming technique characterized by the ability to convert two-dimensional ribbons to three-dimensional structures. However, most 3D structures woven from straight ribbons have topological defects. Baek et al. proposed a method to weave smoother continuous 3D surface structures using naturally curved (in-plane) ribbons, obtained a new surface structure with relatively continuous variation of Gaussian curvature, and analyzed its geometric properties. We believe that this new 3D surface structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated a 3D surface structure using naturally curved (in-plane) ribbon weaving, and the results of calculations and experiments show that such structures have better buckling stability than those woven with straight ribbons. It is observed that the number of ribbons influences the buckling behavior of different types of woven structures.

Brain is the most complex organ in the human body and it is divided into two hemispheres - left and right hemispheres. Left hemisphere is responsible for control of right side of our body whereas right hemisphere is responsible for control of left side of our body. Brain image segmentation from different neuroimaging modalities is one of the important parts in clinical diagnostic tools. Neuroimaging based digital imagery generally contain noise, inhomogeneity, aliasing artifacts, and orientational deviations. Therefore, accurate segmentation of brain images is a very difficult task. However, the development of accurate segmentation of brain images is very important and crucial for a correct diagnosis of any brain related diseases. One of the fundamental segmentation tasks is to identify and segment inter-hemispheric fissure/mid-sagittal plane, which separate the two hemispheres of the brain. Moreover, the symmetric/asymmetric analyses of left and right hemispheres of brain structures are important for radiologists to analyze diseases such as Alzheimer's, Autism, Schizophrenia, Lesions and Epilepsy. Therefore, in this paper we have analyzed the existing computational techniques used to find brain symmetric/asymmetric analysis in various neuroimaging techniques (MRI/CT/PET/SPECT), which are utilized for detecting various brain related disorders.

Lack of shock absorption capability of conventional steel bollards causes significant vehicle damage and consequently high repair costs. This research studies a solution to reduce vehicle damage by inserting PLA honeycomb structures. A honeycomb-inserted bollard was designed based on numerical simulations using LS-DYNA, which yielded the bollard designed for actual vehicle-bollard collision experiments. Simulation efforts were focused on calculating the acceleration characteristics when a vehicle collides with steel and honeycomb-inserted bollards. Compared to the simulated steel bollards, 20 MPa yield-strength honeycomb-inserted bollard showed 0.017s delay in the maximum acceleration occurrence time, reduction of the maximum acceleration to 37.4% of that of steel bollards, and 13.1% reduction in the B-pillar maximum acceleration. Actual vehicle-bollard collision experiments, with a gyro-sensor installed at the test vehicle front bumper frame, also proved improved shock absorption characteristics of the honeycomb-inserted bollards. An experiment with honeycomb-inserted bollard showed 0.783s delay in the maximum acceleration occurrence time, a significant delay when compared to steel bollards. The maximum acceleration measured by the gyro-sensor was 0.35m/s2 when the simulation predicted it to be 0.388 m/s2, proving the similarity in the simulations and experiments. Thus, this study of shock absorption characteristics promised reduced damage to vehicles and lower repair cost.

We study the resonant dipole-dipole interaction energy between two uniformly accelerated identical atoms, one excited and the other in the ground state, prepared in a correlated Bell-type state, and interacting with the scalar field or the electromagnetic field nearby a perfectly reflecting plate. We suppose the two atoms moving with the same uniform acceleration, parallel to the plane boundary, and that their separation is constant during the motion. We separate the contributions of vacuum fluctuations and radiation reaction field to the resonance energy shift of the two-atom system, and show that Unruh thermal fluctuations do not affect the resonance interaction, which is exclusively related to the radiation reaction field. However, nonthermal effects of acceleration in the radiation-reaction contribution, beyond the Unruh acceleration-temperature equivalence, affect the resonance interaction energy. By considering specific geometric configurations of the two-atom system relative to the plate, we show that the presence of the mirror significantly modifies the resonance interaction energy between the two accelerated atoms. In particular, we find that new and different features appear with respect to the case of atoms in the free space, related to the presence of the boundary and to the peculiar structure of the quantum electromagnetic field vacuum in the locally inertial frame. Our results suggest the possibility to exploit the resonance interaction between accelerated atoms, as a probe for detecting the elusive effects of atomic acceleration on radiative processes.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

In this paper, we present a new parametric class of optimal fourth-order iterative methods to estimate the solutions of nonlinear equations. After the convergence analysis, we study the stability of this class by using the tools of complex discrete dynamics. This allows us to select those elements of the class with lower dependence on initial estimations. We verify by means of numerical tests that the stable members on quadratic polynomials perform better than the unstable ones, when applied to other non-polynomial functions. We also compare the performance of the best elements of the family with known methods, such as the schemes by Newton or Chun, among others, showing robust and stable behaviour.

Thermal interface material (TIM) that can exist as liquid at the service temperature enables efficient heat transfer across two adjacent surfaces in electronic applications. In this work, the thermal conductivities of different phase regions in the Ga-In system at various compositions and temperatures are measured for the first time. A modified comparative cut bar technique is used for the measurement of the thermal conductivities of In_xGa_1-x (x=0, 0.1, 0.214, 0.3, and 0.9) alloys at 40, 60, 80, and 100^oC that are the temperatures commonly encountered in consumer electronics. The thermal conductivity values for the liquid and semi-liquid (liquid+β) Ga-In alloys are higher than the TIM currently used in consumer electronics. These measured quantities, along with the available experimental data from the literature, served as input for the thermal conductivity parameter optimization using the CALPHAD (CALculation of PHase Diagram) method for the pure elements, solution phase, and two-phase region. A set of self-consistent parameters for the description of the thermal conductivity of the Ga-In system is obtained. There is good agreement between the measured and calculated thermal conductivity values for all the phases. Hence, it can be envisaged that liquid/semi-liquid Ga-In alloys can be considered as a potential TIM in consumer electronics due to its high thermal conductivity.

Powder and SLM additively manufactured parts of X5CrNiCuNb17-4 maraging steel were systematically investigated by electron microscopy to understand the relationship between the properties of the powder grains and the microstructure of the printed parts. We prove that satellites, irregularities and superficial oxidation of powder particles can be transformed into an advantage through the formation of nanoscale (AlMnSiTiCr)-oxides in the matrix during the printing process. The nano-oxides showed extensive stability in terms of size, spherical morphology, chemical composition and crystallographic disorder upon in situ heating up to 950°C in the scanning transmission electron microscope. Their presence thus indicates a potential for oxide-dispersive strengthening of this steel, which may be beneficial for creep resistance at elevated temperatures. The nucleation of copper clusters and their evolution into nanoparticles as well as the precipitation of Ni and Cr particles upon in situ heating have as well been systematically documented.

This research presents the Cross-Cultural Intelligent Language Learning System (CILS), a novel approach integrating Artificial Intelligence (AI) into language education to enhance cross-cultural communication. CILS utilizes advanced AI technologies to provide adaptive, personalized learning experiences that cater to the unique linguistic and cultural backgrounds of each learner. By dynamically adjusting content and methodology, CILS significantly improves linguistic proficiency and cultural understanding, essential for effective global interactions. The implementation of CILS in platforms such as Busuu and HelloTalk has demonstrated marked improvements in engagement and communication skills among learners. Empirical studies validate the system's effectiveness in real-world settings, showing enhanced learner performance and increased intercultural competence. Additionally, the Technology Acceptance Model (TAM) applied confirms that the usability and perceived usefulness of AI-driven systems strongly influence learner acceptance and sustained use. This study not only underscores the potential of AI in transforming language education but also highlights the critical role of cultural sensitivity in designing educational technologies.

Analysing the human body by direct observation can lead to misinterpretation of underlying trends, whereas in vitro organ models facilitate their understanding. Likewise, in vitro organ models serve as valuable tools for assessing the toxicity of compounds. However, none of the existing models had the features we considered critical for toxicity assessment, so we developed an in vitro liver model for toxicity assessment. We used four different types of primary liver cells: Hepatic sinusoidal endothelial cells, hepatic stellate cells, Kupffer cells and hepatocytes. We cultured them in different combinations of composition and volume of cell medium, hepatocyte proportion of total cells, and addition of extracellular matrix. We added rifampicin, ibuprofen and 5-fluorouracil to this model and observed the microanatomy and physiology changes for a week with preclinical and clinical instruments. Among the different model configurations, we selected the feature combination of the in vitro model that had similar biomarker values to those measured by the clinical instruments used in clinical diagnostics. When we exposed the selected model configuration to rifampicin, ibuprofen and 5-fluorouracil, the viability of Kupffer cells and liver sinusoidal endothelial cells was significantly lower than in the untreated samples. In contrast, we observed negligible viability of hepatocytes compared to the untreated samples. We have built an in vitro liver model that resembles the liver microenvironment and we have analysed it with clinical instrumentation to facilitate the data translation. In this sense, we have established that Kupffer and LSEC cells are suitable candidates for the search for clinical diagnostic markers of liver function.

Museums are called to respond to contemporary challenges and contribute to the formation of more progressive societies. One of the major challenges of our time is climate change and museums could construct cocreated narratives around climate and implement targeted actions for the audiences through their sensorial and affective experiences. More specifically, Geology and Palaeontology museums are repositories of knowledge on geoheritage and geoconservation, recognized for their scientific, pedagogical, cultural and recreational values. The educational potential of geological and paleontological exhibits could be used in informal education activities regarding the climate emergency. Taking the above into consideration, this study focuses on both the creation and evaluation of an educational program for the Natural History Museum of Arsakeio Campus at Psychicko.

Surfactants are widely used in the synthesis of nanoparticles, as they have a remarkable ability to direct their growth to obtain well-defined shapes and sizes. However, their post-synthesis removal is a challenge, and the methods used often result in morphological changes that defeat the purpose of the initial controlled growth. The cleaning methods could be classified as thermal or non-thermal. In general, the structure of materials can be better preserved by non-thermal treatments. After the removal of surfactants, the highly active surfaces of nanomaterials may undergo structural reconstruction by exposure to a different environment. Thus, ex situ characterization after air exposure may not reflect the effect of the cleaning methods. In situ characterization is required to better understand the impact of various cleaning procedures. Combining X-ray photoelectron spectroscopy, in situ infrared reflection absorption spectroscopy, and environmental transmission electron microscopy measurements with CO probe experiments, we investigated different surfactant-removal methods to produce clean metallic Pt nanoparticles from surfactant-encapsulated ones. Non-thermal plasmas show the best results. It was demonstrated that both UV-ozone treatment and room temperature O2 plasma treatment lead to the formation of Pt oxides on the surface after the removal of the surfactant. These oxides are reduced to metallic Pt during in situ CO probe experiments. On the other hand, when H2 was used for plasma treatment, the Pt0 oxidation state and nanoparticle size distribution were preserved. In addition, H2 plasma treatment can reduce Pt oxides after O2-based treatments, resulting in metallic nanoparticles with clean surfaces. Thermal reduction in hydrogen leads to carbon species emerging onto nanoparticle surfaces after heating and agglomeration of Pt nanoparticles. Particularly, O2-based thermal treatments result in the formation of aggregates consisting of small nanoparticles. These findings provide a better understanding of the various options for surfactant removal from metal nanoparticles and point toward non-thermal plasmas as the best route if the integrity of the nanoparticle needs to be preserved.

This study assesses the impact of globalization on female participation in the labor force (FPLF). The increased globalization in the last several decades has created various economic opportunities for enterprises and individuals worldwide at an unprecedented rate. As a result, it has helped improve the quality of life for many men and women. In this process, the issue of women’s economic participation has been a critical topic for discussion worldwide. In that context, the objective of the paper is to determine if FPLF is influenced by a country’s participation in foreign markets through foreign direct investment (FDI) – a proxy for globalization. The paper uses a panel dataset obtained from the World Bank’s World Development Indicators database for 99 countries from 2001 to 2018. We then use system Generalized Method of Moments (system GMM) to estimate a dynamic panel model with appropriate specification tests. The results show that the positive effects of FDI on FPLF are more robust for low- and middle-income countries than high-income countries. We also find that results may be sensitive to outlier observations. Our results explain the seemingly inconclusive results within existing literatures and suggest that low- and middle-income countries should particularly focus on sectors that generate FDI as they stand to yield the greatest benefits with regards to female economic empowerment.

The cubic B2 to monoclinic B19’ martensitic transformation in NiTi shape memory alloys proceeds by the nucleation and propagation of habit plane interfaces that remain undistorted and unrotated by the transformation. Due to incompatibility of austenite and martensite lattices in NiTi, the interfaces form between austenite and twinned martensite as described by Phenomenological Theory of Martensite Crystallography (PTMC). This have been assumed also for stress-induced martensitic transformation where, however, interfaces with single martensite variant have been frequently reported. On this account, we propose a different solution of strain compatibile habit planes by considering the effect of elastic deformation of both lattices due to external stress. Using modified PTMC theory, we evaluate the magnitudes and orientations of the critical uniaxial stress in tension and compression for which strain compatible habit plane interfaces with a single variant of martensite can form. The calculated stress is too high, but considering the pre-transformation softening of the C’ elastic constant for the {110}A⟨110⟩A austenite shear mode, the critical stress decreases down to 500 MPa. For such situation, we analyse orientation dependence and tension-compression asymmetry of required C’ softening, and the orientations of strain compatible habit planes that are compared with available experimental results. All calculations, including source code and interactive graphs, are available for download.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Lunar grabens are the largest tensional linear structures on the Moon. In this paper, 17 grabens were selected to investigate the dips and displacement-length ratios (γ) of graben-bounding faults. Several topographic profiles were generated from selected grabens to measure their rim elevation, width and depth through SLDEM2015 (+LOLA) data. The differences in rim elevation (∆h) and width (∆W) between two topographic profiles on each graben were calculated, yielding 146 sets of data. We plotted ∆h versus ∆W for each and calculated the dip angle (α) of graben-bounding faults. A dip of 39.9° was obtained using the standard linear regression method. In order to improve accuracy, large error data was removed based on error analysis. The results 49.4° and 52.5° were derived by the standard linear regression and mean methods, respectively. Based on the depth and length of grabens, the γ value of the graben-bounding normal fault is also studied in this paper. The γ value is 3.6×10-3 for lunar normal faults according to the study of grabens and the Rupes Recta normal fault. After obtaining the values of α and γ, the increase in lunar radius caused by the formation of grabens was estimated. We suggest that the lunar radius has increased by around 130 m owing to the formation of grabens. This study could aid in the understanding of normal fault growth and provide important constraints on the thermal evolution of the Moon.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

This is a theoretical and empirical article. In the first part, an original definition of the cross-border market for cultural services has been developed, based on classic market definitions. The structure and conditions of functioning for this market have also been presented. The next part of the article discusses the supply side of the cross-border market of cultural services for the two twin towns: Cieszyn (Poland) and Český Těšín (Czech Republic). Next, based on the surveys conducted, the participation of residents of both towns in the most important cultural events organised by cultural institutions on both sides of the border was examined.

Graphene and borophene are highly attractive two-dimensional materials with outstanding physical properties. In this study we employed a combined atomistic continuum multiscale modeling to explore the effective thermal conductivity of polymers nanocomposites made of PDMS polymer as the matrix and graphene and borophene as nanofillers. We first conduct classical molecular dynamics simulations to investigate the interfacial thermal conductance between graphene/PDMS and borophene/PDMS interfaces. Acquired results confirm that the interfacial thermal conductance between nanosheets and polymer increases from the single-layer to multilayered nanosheets and finally converges. The data provided by the atomistic simulations were then used in the finite element method simulations to evaluate the effective thermal conductivity of polymer nanocomposites at continuum level. We explore the effects of nanofillers type, their volume content, geometry aspect ratio and thickness on the nanocomposites effective thermal conductivity. As a very interesting finding, we show that borophene nanosheets, despite almost two orders of magnitude lower thermal conductivity than graphene, can yield very close enhancement in the effective thermal conductivity in comparison with graphene, particularly for low volume content and small aspect ratios and thicknesses. We conclude that for the polymer-based nanocomposites, significant improvement in the thermal conductivity can be reached by improving the bonding between the fillers and polymer or in another word enhancing the thermal conductance at the interface. By taking into account the high electrical conductivity of borophene, our results suggest borophene nanosheets as promising nanofillers to simultaneously enhance the polymers thermal and electrical conductivity.

Fever control is essential in patients with severe traumatic brain injury (TBI). The efficacy of therapeutic hypothermia (TH) in severe TBI has been investigated over the last few decades; however, in contrast to experimental studies showing benefits, no evidence of efficacy has been demonstrated in clinical practice. In this review, the mechanisms and history of hypothermia were briefly outlined, while the results of major randomized controlled trials (RCTs) and meta-analyses investigating TH for adult TBI are introduced and discussed. The retrieved meta-analyses showed conflicting results, with a limited number of studies indicating benefits of TH. Some studies have shown benefits of long-term TH compared with short-term TH. Although TH is effective at lowering elevated intracranial pressure (ICP), reduced ICP does not lead to favorable outcomes. Low-quality RCTs overestimated the benefits of TH, while high-quality RCTs showed no difference or worse outcomes with TH. RCTs assessing standardized TH quality demonstrated the benefits of TH. As TBI has heterogeneous and complicated pathologies, applying a uniform treatment may not be ideal. A meta-analysis of young patients who underwent early cooling and hematoma removal showed better TH results. TH should not be abandoned, and its optimal should be advocated on an individual basis.

The massive amount of human biological, imaging and clinical data produced by multiple and diverse sources, necessitates integrative modeling approaches able to summarize all this information into answers to specific clinical questions. In this paper, we present a hypermodeling scheme able to combine models of diverse cancer aspects regardless of their underlying method or scale. Describing tissue-scale cancer cell proliferation, biomechanical tumor growth, nutrient transport, genomic-scale aberrant cancer cell metabolism, and cell signaling pathways that regulate the cellular response to therapy, the hypermodel integrates mutation, miRNA expression, imaging, and clinical data. The constituting hypomodels as well as their orchestration and links are described. Two specific cancer types, Wilms tumor (nephroblastoma) and non-small cell lung cancer, are addressed as proof of concept study cases. Personalized simulations over the actual anatomy of a patient have been carried out. The hypermodel has also applied to predict tumor control after radiotherapy and the relationship between tumor proliferative activity and response to neoadjuvant chemotherapy. Our innovative hypermodel holds promise as a digital twin based clinical decision support system and the core of future in silico trial platforms, although additional retrospective adaptation and validation is necessary.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

Urinary tract diseases are common in cats, and often require surgical reconstruction. Here, to explore the possibility of urinary tract reconstruction in cats using in-vivo tissue architecture (iBTA), biosheets fabricated using iBTA technology were implanted into the feline bladder and the regeneration process was histologically evaluated. The biosheets were prepared by embedding molds into the dorsal subcutaneous pouches of six cats for 2 months. A section of the bladder wall was removed, and the biosheets were sutured to the excision site. After 1 and 3 months of implantation, the biosheets were harvested and evaluated histologically. Implantable biosheets were formed with a success rate of 67%. There were no major complications following implantation, including tissue rejection, severe inflammation, or infection. Urinary incontinence was also not observed. Histological evaluation revealed the bladder lumen was almost entirely covered by urothelium after 1 month, with myofibroblast infiltration into the biosheets. After 3 months, the urothelium became multilayered, and mature myocytes and nerve fibers were observed at the implantation site. In conclusion, this study showed that tissue reconstruction using iBTA can be applied to cats, and that biosheets have the potential to be useful in both the structural and functional regeneration of the feline urinary tract.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

Ensuring access to water, sanitation, and hygiene (WASH) facilities, coupled with behavior change education in schools, is fundamental for fostering a conducive learning environment and promoting principles of inclusion, dignity, and equality. This study focuses on 12 primary schools in Anápolis, Brazil, encompassing 4,394 students and 248 teachers. WASH assessments were conducted through a questionnaire, observation of water and sanitation facilities and structures, and microbiological analysis. Over the period 2018 to 2020, the proportion of schools with safely managed drinking water surged from 42% to 92%. However, sanitation conditions in the schools were categorized as a basic level, with hygiene services rated as limited in 92% of the schools due to the absence of soap. While this study reveals that Anápolis schools generally align with WASH guidelines for basic/advanced drinking water services, there is a crucial need for enhancements in both hardware and software facilities to address sanitation and hygiene challenges.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

The economical load dispatch problem is a critical concern in thermal power systems to ensure cost-effective operation. This paper conducts a comparative analysis between the Social Spider Algorithm (SSA) and Particle Swarm Optimization (PSO) for economical load dispatch in a 6-unit thermal power system with the integration of 11,000 plug-in electric vehicles (PEVs). Both SSA and PSO are population-based optimization techniques designed to minimize the overall fuel cost while satisfying the load demand by determining the optimal power output of each unit. SSA emulates the social behavior of spiders, while PSO simulates the collective intelligence of a swarm of particles. Performance evaluation of the algorithms considers power system data, such as unit fuel costs, minimum and maximum loads, and total load demand. The objective is to minimize fuel cost while meeting the load demand. Comparative analysis of SSA and PSO includes convergence speed, solution quality, and computational efficiency. Experimental results indicate that SSA outperforms PSO in achieving a more optimal and economical load dispatch solution for the 6-unit thermal power system. SSA demonstrates faster convergence and provides superior-quality solutions compared to PSO. This paper contributes to the field by highlighting SSA's effectiveness in achieving cost-efficient operation of thermal power systems. The findings suggest that SSA holds promise as an optimization technique for similar power system optimization problems, enhancing overall operational efficiency and reducing costs for thermal power plants.

Based on the kinematic approach of the limit analysis and slip-line theories, this paper proposes a new 2D analytical model to evaluate the collapse support pressure to ensure the face stability of a circular tunnel in purely cohesive soils driven by a shield. The normality conditions, the yield criterion and the vertical soil arching effect are considered in the analytical model. Two upper bound solutions corresponding to the ratio of the cover to the diameter (C/D) are derived from considering the mechanisms based on the motion of rigid multi-blocks. Comparisons are made with existing upper and lower bound solutions published in previous articles. The results are close to the solutions of practical engineering. The failure mechanisms proposed in this study provide a better explanation for the failure process in the heading of the tunnel face.

The main inhibitory neurotransmitter in the mammalian brain is 4-aminobutyric acid (GABA). Phthalimide acts as a sodium channel antagonist, one of the finest targets for treating epilepsy is the sodium channel and JNK kinase activity is inhibited to treat epilepsy. a novel compound with multiple targets of action for the treatment of epilepsy also anti-oxidant activity has been designed. The compounds are designed in two series aldehydes and aniline. Docking of all the designed compounds has been done with the suitable protein GABA-AT, sodium channel, JNK protein, and anti-oxidant from protein bank. QSAR was done for constructing many linear regression models. In combination with the developed Docking and QSAR outcomes, ADMET has been performed for the active compounds. The result shows that 11 of the compounds have excellent binding energy in docking with all the receptors and also have good QSAR results and follow the ADMET. The structural understanding of human GABA-AT inhibition was obtained from molecular dynamics simulation studies for compound no. 11 at 5 nanoseconds. Synthesis and pharmacological activity also suggest that the designed compound no.11 be considered the best Novel Compound.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

Human displacement is on the rise globally, and the increase in the burden of tuberculosis (TB) is also attributed to migrations worldwide. A significant number of such displacement occur in regions with considerably higher areas of TB burden. Displacements may delay in TB diagnosis and treatment, which possibly will lead to TB transmission among healthy individuals. In this study, we assessed the association of existing determinants after a protracted internal displacement of people with the delay in TB diagnosis and treatment outcomes. A cross-sectional study was conducted on internally displaced TB patients registered at selected health facilities in three urban districts of Pakistan from March 2019 to February 2020. The univariate and multivariate logistic regression model was used to assess the delay in diagnosis and treatment outcomes. IDPs with delay in initiation of treatment beyond 30 days were at high possibility of unsuccessful TB treatment outcomes (adjusted odds ratio AOR,2.60; 95% CI 1.06-6.40). Analysis of factors that affect health seeker behavior and timely treatment showed a significant association (p<0.05) in-between age group 55-65 years (AOR, 2.66; 95% CI 1.00-7.07), female patients (AOR, 2.42; 95% CI 1.21-4.81), visited non-formal health provider (AOR, 8.81; 95% CI 3.99-19.46), self-medication (AOR, 2.72; 95 % CI 1.37-5.37), poor knowledge of TB (AOR, 11.39; 95% CI 3.31-39.1), and perceived stigma (AOR, 8.81; 95% CI 3.99-19.4). Prolong delay in treatment was associated with unfavorable treatment outcomes among IDPs, more specifically. As migrants and IDPs are more likely to experience an interruption in care due to overall exclusion from social and health care services. Therefore, it is imperative to understand the barriers in providing public health care services, particularly in preventing and treating TB.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

: Cybersecurity has become a critical area in the digital field in recent years. The expansion of networks has revolutionised the way network structures are organised and managed. However, with increased connectivity and the growing complexity of modern networks, the threat of cyber-attacks has become more intense. As technology continues to advance, it brings both opportunities and challenges. One of the major challenges is the need to secure networks and sensitive data from various malicious activities. Traditional networks have evolved to include Software Defined Network (SDN), which offers a more flexible and programmable framework. Researchers should focus on detecting attacks in SDN because SDN networks are becoming more popular and attractive targets for clients due to their programmability and dynamic nature. The centralised controller, known as the backbone of an SDN, becomes a single point of failure and a potential target for attackers if not properly secured. Researchers need to emphasise the detection of attacks in SDN in order to mitigate these risks. By understanding the potential vulnerabilities and attack methods specific to SDN, researchers can develop effective detection approaches and propose countermeasures. This methodology helps protect the network from potential threats and minimises the impact of successful attacks. Therefore, this survey paper provides a review of Intrusion Detection Systems (IDSs) in Software-Defined Networks (SDN) to provide a thorough understanding of SDN security issues.

Oilseed plants of the Brassicaceae plant family are cultivated for food, feed and industrial purposes on large-scale in Europe. This review gives an overview of current market-oriented applications of new genomic techniques (NGTs) in relevant Brassicaceae oilseed crops based on a literature survey. In this respect, changes in oil quality, yield, growth and resistance to biotic and abiotic stress are goals in oilseed rape (B. napus) and camelina (C. sativa). Environmental risk assessment scenarios are developed for specific NGT applications in Brassicaceae oilseed crops with either a changed oil composition or with fitness related traits. In case of a changed oil composition an increase or decrease of polyunsaturated fatty acids (PUFA) demonstrates risks for health and survival of pollinators. In case of fitness related traits other risks were identified, i. e. an increased risk of spread and persistence of NGT plants. Furthermore, there are indications for potential disturbance of interactions with the environment, involving signalling pathways and reaction to stress conditions. It is shown that for a comprehensive risk assessment the technological potential of NGTs, the plants’ biology and the scale of releases have to be considered in combination. Therefore, the release of NGT plants into the environment for agricultural purposes will require risk assessment and monitoring of single traits as well as of combinatorial and long-term cumulative effects. In addition, risk management should develop concepts and measures to control and potentially restrict the scale of releases. This is especially relevant for NGT Brassicaceae in Europe which is a centre of diversity of this plant family.

According to Quantum Mechanics a narrow wave-package of the center of mass of macroscopic objects, due to their heavy mass, remains stable over astronomical times. However Quantum Mechanics allows and energetically even prefers largely smeared out c.m. states that never been seen. Why is this the real state of the world we know? Does it suggest a micro-macro threshold with different theoretical descriptions?

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

The transmission of light is one of the key optical processes in the terrestrial environment (the atmosphere and underlying surfaces). The dependence of light transmittance on the illumination/observation conditions and optical properties of the atmosphere–underlying system can be studied using the integro-differential radiative transfer equation. However, for numerous applications a set of analytical equations is needed to describe the transmitted light intensity and flux. In this paper, we describe various analytical techniques to study light transmittance through light scattering and absorbing media. A physical significance and improved mathematical accuracy of approximations are provided using the analytical models for the diffusion exponent, average cosine of the light field, spherical and plane albedos. The accuracy of various approximations is studied using exact radiative transfer calculations with various scattering phase functions, single-scattering albedos, observational conditions, and optical depths.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

In the world's first pig-to-human cardiac xenotransplant, the elevated levels of porcine cytomeg-alovirus (PCMV) are considered key factors contributing to patient mortality. This has renewed attention to PCMV, a virus widely prevalent in pigs. Currently, there are no effective drugs or vaccines targeting PCMV, and its high detection difficulty poses challenges for prevention and control research. In this study, antiviral small hairpin RNA (shRNA) was selected and inserted into the Rosa26 and miR-17-92 loci of pigs via a CRISPR/Cas9-mediated knock-in strategy. Further in vitro viral challenge experiments demonstrated that these genetically edited pig cells could effec-tively limit PCMV replication. Through this process, we constructed a PCMV-infected cell model, validated partial viral interference sites, enhanced gene knock-in efficiency, performed gene editing at two different gene loci, and ultimately demonstrated that RNA interference (RNAi) technology combined with CRISPR/Cas9 has the potential to generate pig cells with enhanced antiviral infec-tion capabilities. This opens up possibilities for the future production of pig populations with anti-viral functionalities.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

Abstract: The SARS-CoV-2 pandemic has reemphasized the urgent need for broad-spectrum antiviral therapies. We developed a computational workflow using scRNA-Seq data to assess cellular metabolism during viral infection. With this workflow we predicted the capacity of cells to sustain SARS-CoV-2 virion production in patients and found a tissue-wide induction of metabolic pathways that support viral replication. Expanding our analysis to influenza A and dengue viruses, we identified metabolic targets and inhibitors for potential broad-45 spectrum antiviral treatment. These targets were highly enriched for known interaction partners of all analyzed viruses. Indeed, phenformin, an NADH:ubiquinone oxidoreductase inhibitor, suppressed SARS-CoV-2 and dengue virus replication. Atpenin A5, blocking succinate dehydrogenase, inhibited SARS-CoV-2, dengue virus, respiratory syncytial virus, and influenza A with high selectivity indices. In vivo, phenformin showed antiviral activity against SARS-CoV-2 in a Syrian hamster model. Our work establishes host metabolism as druggable for broad-spectrum antiviral strategies, providing invaluable tools for pandemic preparedness.

The feeling of beauty is one of the positive human feelings. In architecture and design, it is associated with forms appropriate to their purpose. The usefulness of products to meet needs is also important. They are well received by users. The task of designers is to achieve perfection in their work. The rational design and use of artificial living environments are expressions of concern for natural resources (sustainable environment). These issues are addressed, i.e., by an interdisciplinary initiative of the New European Bauhaus. The aim of the paper is to expand knowledge about beauty and utility. They are important when choosing mass-produced goods. The article uses research methods: interpretive research, analyses, comparisons, logical argumentation, etc. Experimental qualitative research using a checklist was used. The results expand the knowledge on the selected topic and research scope of the research of the paper. The survey can be used to rationally evaluate architecture, interiors, and design facilities. It can be helpful for various aesthetic and functional strategies dedicated to different users. The paper demonstrates the role of beauty and functionality in the built environment. They are analyzed in the context of social and technical conditions, as well as contemporary sustainable design

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

: The silicon single crystals for semiconductor application is usually grown by Czochralski (CZ) method. This paper researches 300mm silicon Czochralski (CZ) crystal growth with CUSP magnetic field for IGBTs substrate application. The different positions of Zero-Gauss plane (ZGP) under CUSP magnetic field are simulated and compared to numerical analysis, investigated melt convection, melt flow velocity near to quartz crucible wall, diffusion boundary layer and effect of initial oxygen concentration in the silicon crystal, and the shape of solid/liquid interface was discussed. The results show that the change of the ZGP of the CMF mainly affects the convection in the melt, which leads to the difference of the thickness of the boundary layer near to the wall of the quartz crucible, and was found to be the key to reduce the oxygen dissolution from the crucible wall and oxygen diffuse into the crystal, along with the differences in the shape of the crystal-melt interface. In addition, we have carried out actual industrial single crystal production under the three configurations. The results show that the experimental data of oxygen content and shape of the crystal-melt interfaces in silicon crystal are consistent with the numerical results.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

The application of space robotic manipulators and heightened autonomy for ios represents a paramount pursuit for leading space agencies, given the substantial threat posed by space debris to operational satellites and forthcoming space endeavors. This work presents a guidance algorithm based on drl to solve for the space manipulator path-planning during the motion synchronization phase with the mission target. The goal is the trajectory generation and control of a spacecraft equipped with a 7-dof robotic manipulator, such that its end effector remains stationary with respect to the target point of capture. The ppo drl algorithm is used to optimize the manipulator’s guidance law, and the autonomous agent generates the desired joints rates of the robotic arm, which are then integrated and passed to a model-based feedback linearization controller. The agent is first trained to optimize its guidance policy and then tested extensively to validate the results against a simulated environment representing the motion synchronization scenario of an ios mission.

Background: Cancer has been one of the most critical health problems during the past decades which require serious consideration, especially in developing countries. Methods: 80 parents of the children with different types of cancers were studied via both questionnaire and person-to-person interview after announcing their informed consent. Results: The highest delay in patients' initial referral was due to the following factors: lack of attention or ignoring the first symptoms, delay in referring to the physician, low economic status and even lack of family support for the patient. In addition, visiting several doctors after the initial diagnosis, uncertainty about the first proposed method, and high cost of treatment can be mentioned as the main causes of delays in the start of treatment. Conclusion: Education plays an important role in identifying the signs of cancer. In addition, proper relationship and cooperation between the health system and physicians as well as provision of adequate information to patients could lead to the long-term cooperation of these patients in continuing their treatment.

This research paper presents an enhanced economic load dispatch (ELD) approach using the Teaching-Learning-Based Optimization (TLBO) algorithm for 10 thermal units, examining the impact of Plug-in Electric Vehicles (PEVs) in different charging scenarios. The TLBO algorithm is utilized to optimize the ELD problem, considering the complexities associated with thermal units. The integration of PEVs in the load dispatch optimization is investigated, and different charging profiles and probability distributions are defined for PEVs in various scenarios, including overall charging profile, off-peak charging, peak charging, and stochastic charging. These tables allow for the modeling and analysis of PEV charging behavior and power requirements within the power system. By incorporating PEVs, additional controllable resources are introduced, enabling more effective load management and grid stability. The comparative analysis showcases the advantages of the TLBO-based ELD model with PEVs, demonstrating the potential of coordinated dispatch strategies leveraging PEV storage and controllability. This paper emphasizes the importance of integrating PEVs into the load dispatch optimization process, utilizing the TLBO algorithm, to achieve economic and reliable power system operation while considering different PEV charging scenarios.

The study was conducted to evaluate the agronomic performance, forage yield, and nutritive values of Desho grass varieties under supplementary irrigation at Dambi Dollo University experimental site, Western Ethiopia. Three Desho grass varieties (Areka /DZF#590, Kindu kosha-1/DZF #591, and Kulumsa /DZF #592) were arranged in randomized complete block design (RCBD) with three replications. The CROPWAT 8.0 model, local climate data, forage data, and soil data were used to determine Desho grass water requirements and irrigation schedules. The agronomic parameters, yield, chemical composition, and in vitro digestibility of the feed samples at standardization cut were determined following the standard procedures. The results showed significant differences (p

An adequate representation of the water infiltration process in the soil allows improving the efficiency in application and the uniformity in surface irrigation. The Green and Ampt model has shown a good representation of the process, and researchers from the United States Department of Agriculture (USDA) determined the values of their parameters for soils of that country, which are shown in tables or through functional relationships and this information is used as reference in several parts of the world, although there is no certainty that they are representative of the soils in Mexico. In this study, the parameters of the Green & Ampt equation were determined and evaluated in some soils of agricultural importance in Mexico. The parameters were obtained in four ways: one of them applied a methodology adapted from Brooks and Corey to quantify the wetting front capillary pressure head and used an permeameter under constant hydraulic head to determine the saturated hydraulic conductivity, and the other three consisted in taking them from three studies reported by the USDA. The values of the parameters suggested in Mexico drastically underestimated the results with relative errors (RE) in a range of -49.0 to -94.0% and the most representative were those obtained with the methodology proposed in this research with RE of -15.0 to 6.0%.

In the area of dental healthcare services, where patients and professionals deal with multiple auditory stimuli, this cross-sectional study reports on the intricate dynamics of sound preferences, noise obstacles, and the profound impact of music on anxiety reduction within dental office set-tings. The sample comprises of 134 dental patients, primarily females (56.7%), with varying age groups, education levels, and therapy durations in the university clinics of the department of Dentistry, National and Kapodistrian University of Athens and four private dental offices at the metropolitan area of Athens, Greece. Notably, 92.5% of the participants report no hearing loss, and 56.7% exhibit some level of noise sensitivity. The study reveals a moderate to good perceived health status (M=3.84, SD=0.95) among participants, with low perceived noise disturbance in university dental clinics. Preferences for instrumental music, foreign pop, and classical music are prominent during waiting times. Potential irritations include impersonal treatment (44%) and staff behavior (41.8%). Music player usage within the settings of the dental clinic involves radios (49.3%) and headphones (41.0%). Correlations and predictors indicate associations between health status, music preferences, and noise disturbances. More specifically, visiting the university dental clinics (β = .300, p = .005) as well as younger age (β = .300, p = .034) were significant predictors of better perceived health status. Clearer perception of external sounds while using the music player (β = .190, p = .039) was a significant predictor of better perceived health status, while poorer health was predicted by the preference of Greek folk songs (β = -.200, p = .030). Also, the use of smartphones for playing music was related to poorer health (β = -.370, p < .001). Following, younger age (β = -.270, p = .015), lower education (β = -.210, p = .035), higher noise sensitivity (β = .190, p = .027), as well as feelings of anxiety and nervousness due to ambient noise from people and machines (β = .510, p = .027) were significant predictors of noise disturbance from machines. Also, visiting private clinics (β = .240, p = .018), preferences of specific playlist (β = .310, p = .012), no music (β = .280, p = .016) and use of smartphones to play music (β = .230, p = .029) were significant predictors of noise disturbance from patients or staff. Finally, the preference of listening to a specific playlist was related to better health status (r = .190, p < .05). Findings aim to optimize eco-soundscapes in dental offices, con-tributing to enhanced patient well-being. The research underscores the potential of music inter-ventions to alleviate dental anxiety and improve the overall dental experience and quality care.

W. L. Edge proved that the internal points of a conic in PG(2,5), together with the collinear triples on the non-secant lines, form the Desargues configuration. M. Saniga showed an intimate connection between Desargues configurations and the generalized quadrangles of order two, GQ(2,2), whose representation has been dubbed “the doily” by Stan Payne in 1973. In this paper we prove that the external points of a conic in PG(2,5), together with the collinear and non-collinear triples on the non-tangent lines, form the generalized quadrangle of order two.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

Current article presents the study of psychological wellbeing of adolescents (n=168, age 15-17) gifted in math, humanities and sports and educated in advanced programs for gifted children. Theoretical framework of this study is eudemonic concept of psychological wellbeing by C. Ryff. Psychological wellbeing is measured with Ryff wellbeing scales in Russian adaptation by L.V. Zhukovskaya and E.G. Troshikhina. The study is aimed at understanding differences in psychological wellbeing of gifted teenagers connected to gender and type of giftedness. The results suggest that general wellbeing score did not differ for adolescents with different types of giftedness or of different genders. Separate components of psychological wellbeing, such as purpose in life and self-acceptance, are influenced by activity connected to the talent. Gender differences are subjected to age-specific trends of personal development in adolescence. Type of giftedness might reinforce these trends.

This study focuses on enhancing controllable fibrin-based hydrogels for tissue engineering, addressing existing weaknesses. By integrating a novel copolymer, we improve the foundation for cell-based angiogenesis with adaptable structural features. Tissue engineering often faces challenges like waste disposal and nutrient supply beyond the 200 µm diffusion limit. Angiogenesis breaks through this limitation, allowing the construction of larger constructs. Our innovative scaffold combination significantly boosts angiogenesis, resulting in longer branches and more capillary network junctions. The copolymer attached to fibrin fibers enables precise adjustment of hydrogel mechanical-dynamic properties for specific applications. Our material proves effective for angiogenesis, even under suppression factors like suramin. In our study, we prepared fibrin-based hydrogels with and without the copolymer PVP12400-co-GMA10mol%. Using a co-culture system of human umbilical vein endothelial cells (HUVEC) and mesenchymal stem cells (MSC), we analyzed angiogenetic behavior on and within the modified hydrogels. Capillary-like structures were reproducibly formed on different surfaces, demonstrating the general feasibility of three-dimensional endothelial cell networks in fibrin-based hydrogels. This highlights the biomaterial's suitability for in vitro pre-vascularization of biohybrid implants.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

In an effort to discover an effective and selective antitumour agent, synthesis and anti-cancer potential of 4-(pyridin-4-yl)-6-(thiophen-2-yl)pyrimidin-2(1H)-one (SK-25), which has been reported earlier by us with significant cytotoxicity towards MiaPaCa-2 malignant cells, with an IC₅₀ value of 1.95 μM and was found to instigate apoptosis. In the present study, the antitumour efficacy of SK-25 was investigated on Ehrlich ascites tumour (solid), Sarcoma 180 (solid) tumour and Ehrlich ascites carcinoma. The compound was found to inhibit tumour development by 94.71% in Ehrlich ascites carcinoma (EAC), 59.06% in Ehrlich tumour (ET, solid) and 45.68% in Sarcoma-180 (solid) at 30 mg/kg dose. Additionally, SK-25 was established to be non-toxic at a maximum tolerated dose of 1000 mg/kg in acute oral toxicity in Swiss-albino mice. Computer-based predictions also show that the compounds could have an interesting DMPK profile. The current study provides insight for further investigation of the antitumour potential of the molecule.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

In this paper, we discuss major issues of mathematics teaching and learning in Nepal. The issues coming from theories such as social and radical constructivism suggest that teachers are not trained to use such approach in teaching mathematics, and there is a lack of teaching aids and materials and technological tools. The issues related to social aspects are gender issues, language issues, social justice issues, and issues related to the achievement gap. The cultural issues are related to the diversity of language and ethnicity. The issues related to political aspects are equity and access, economic status, pedagogical choice, and professional organizations and unions. The issues related to technology include the technological skills, use of technology, and affordance. Finally, we suggest that all the stakeholders should pay attention to resolving these issues by improving the curriculum, training teachers, resourcing the classroom with locally made and new technological tools.

The numerous biological activities of phenothiazine and sulphonamide derivatives, especially their antibacterial qualities, have attracted so much interest. In this study, the synthesis and characterization of phenothiazine-3-sulphonamide derivatives and evaluation their antimicrobial activity against the following pathogenic microorganisms is reported. Two gram-positive bacteria; (Staphylococcus aureus, and Streptococcus pyogenes), two gram-negative bacteria; (Escherichia coli, and Salmonella typhi) as well as one fungus (Aspergillus fumigatus) were used while ciprofloxacin, gentamycin and ketoconazole served as standard drugs. The synthesis of the derivatives was achieved through a base catalyzed the reaction of 4-chloroaniline with 1-naphthylamine to form 1-(naphthalen-1-yl) benzene-1,4-diamine. This intermediate was then treated with sulphur and iodine to yield the phenothiazine derivative while subsequent treatment of the phenothiazine compound with sulphonyl chlorides gave the final products. The synthesized compounds were characterized via proton nuclear magnetic resonance (1HNMR), carbon-13 nuclear magnetic resonance (13C NMR) and Fourier-transform infrared (FTIR) spectroscopic techniques. The minimum inhibitory concentration (MIC) of each compound was then determined using the agar well diffusion method. To predict the binding energies and patterns of the synthesized compounds with target proteins of the above mentioned microorganisms, molecular docking simulations were run using Autodock Vina software (version 4.2). The spectra data of the compounds for FTIR, 1H NMR and 13C NMR (δ) spectral data were consistent with the assigned structures of the synthesized compounds. The binding energies (kcal/mol) for in silico antimicrobial studies were in the range -5.1 to -7.6 kcal/mol. The MIC values were in the range -3.5 to 1.0 mg/L. The results of the in vitro test revealed that the synthesized compounds exhibits promising antimicrobial activity, and showed excellent bactericidal and fungicidal activities. The results obtained showed that the synthesized compounds possess drug-like properties and are good starting materials for drug production.

In this paper, an iterative procedure to find the solution of a nonlinear structural model is introduced. The model presents different multiplicities where parameters are randomly selected within a solvability region. To achieve this aim, a class of multipoint fixed-point iterative schemes for single roots is modified to find multiple roots, reaching the fourth order of convergence. Complex discrete dynamics techniques are employed to select the members with the most stable performance. The structural problem, as well as some academic problems involving multiple roots, are solved numerically to verify the theoretical analysis, robustness and applicability of the proposed scheme.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

Physics behind collimated highly directional nature of lasers, and factors that keep the seven coloured waves that form white light together during their journey from Sun to Earth, in the face of the natural disruptive forces, is not fully understood. Energy levels were measured, in terms of alterations in induced current and voltage, in beams from a red laser, white LED light and the Sunlight before and during their disruption by diffusers (frosted glass for the lasers) and diffractors (diffraction grating for the white light) using a photovoltaic solar cell panel attached to a digital multimeter. Results show that disruption of the beams results in release of extra energy named as ‘Latent Light Binding’ Energy’. It is hypothesized that the ‘binding’ energy keeps laser waves firmly bound together both end-on and side-on enabling laser beams to travel long distances in collimated manner. Likewise, the 7 coloured waves that constitute white light are kept together, probably side-on, in their journey from the Sun to the Earth. The observation that diffraction of sunbeam is associated with increased power generation provides a new lead to improve harnessing of solar energy, where, currently, the focus is mainly on improving efficiency of photovoltaic cell.

This article explores the relationship between convex functions defined on integers ($\mathbb{Z}$) and their extension to real numbers ($\mathbb{R}$). We introduce key definitions and investigate the hypothesis that there exists a unique convex curve within this family of functions, leading to a proof by contradiction. Our findings highlight the preservation of convexity as functions transition from integers to real numbers.

Infections caused by KPC-producing K. pneumoniae continue to pose a significant clinical challenge due to emerging resistance to new antimicrobials. We investigated the association between two drugs whose roles have been repurposed against multidrug-resistant bacteria: fosfomycin and temocillin. Temocillin exhibits unusual stability against KPC enzymes, while fosfomycin acts as a potent “synergizer”. We conducted in vitro antimicrobial activity studies on 100 clinical isolates of KPC-producing K. pneumoniae using a combination of fosfomycin and temocillin. The results demonstrated synergistic activity in 91% of the isolates. Subsequently, we assessed the effect on Galleria mellonella larvae using 5 different KPC-Kp isolates. The addition of fosfomycin to temocillin increased larvae survival from 73 to 97% (+Δ 32%; isolate 1), from 93 to 100% (+Δ 7%; isolate 2), from 63 to 86% (+Δ 36%; isolate 3), from 63 to 90% (+Δ 42%; isolate 4), and from 93 to 97% (+Δ 4%; isolate 10), respectively. Among the temocillin-resistant KPC-producing K. pneumoniae isolates (24 isolates), the addition of fosfomycin reduced temocillin MIC values below the resistance breakpoint in all isolated except one. Temocillin combined with fosfomycin emerges as a promising combination against KPC-producing K. pneumoniae, warranting further clinical evaluation.

Introduction: The combination of Virtual Screening (VS) techniques with in vivo screening in the zebrafish model is currently being used in tandem for drug development in a faster and more efficient way. Areas covered: We review the different virtual screening techniques, the use of zebrafish as a vertebrate model for drug discovery and the synergy that exists between them. Expert opinion: We highlight the advantages of combining virtual and zebrafish larvae screening for drug discovery. On the one hand, VS is a faster and cheaper tool for searching active compounds and possible candidates for therapy than in vivo screening when processing large compound libraries. On the other hand, zebrafish larvae form a vertebrate model which allows in vivo screening of large amounts of the compounds. Importantly physiology and chemical response are mostly conserved between zebrafish and mammals. The availability of the transgenic and mutant zebrafish lines allows an analysis of a specific phenotype upon treatment along with toxicity, off-target effect, side effects, and dosage. Advantages of VS, in vivo whole animal approach screening, and the screening combinations are also reviewed.

Piceatannol is a naturally occurring polyphenolic compound that is widely found in grapes, blueberries, mushrooms, passion fruit and other edible fruits and vegetables. It has a variety of biological activities and pharmacological effects, including anti-inflammatory, antioxidation, antiaging, antiviral, antitumor, anticancer, antiatherosclerosis, antiparasitic, immunoregulatory, and cardiovascular protection effects. The aim of this study was to investigate the antiherpesvirus effects of piceatannol. Pseudorabies virus (PRV) belongs to the family Herpesviridae. PRV has a wide host range and can cause cytopathic effects (CPEs) in PK-15 cells. Therefore, PRV was used as a model to study the antiherpesvirus effect of piceatannol. In this study, we evaluated the antiviral activity of piceatannol against PRV in vitro and in vivo. The results showed that piceatannol could reatrain PRV multiplication in PK-15 cells in a dose-dependent manner. The 50% inhibitory concentration (IC50) was 0.0307 mg/mL, the IC50 was 0.0307 mg/mL, and the selectivity index (SI, CC50/IC50) was 3.68. The addition of piceatannol at different stages of PRV infection inhibited the viral adsorption and intracellular replication phases of PRV. Piceatannol significantly reduced the expression levels of the IE180, EP0, UL29, UL44, US6 and UL27 genes of PRV within 48 h, significantly reduced the expression levels of the PRV gB and gD proteins, and reduced PRV-induced apoptosis. Molecular docking showed that piceatannol had good binding activity with the PRV gB and gD proteins. The results of animal experiments in vitro indicated that piceatannol could delay the onset of disease, improve the survival rate of the mice (14.3%), reduce the viral load in the brain and kidney of the mice, alleviate the pathological changes in the mouse tissues and organs, and increase the levels of TNF-α, IEN-γ and IL-4 in the serum of the mice. These data indicate that piceatannol has good anti-PRV activity in vitro and in vivo, indicating that it could be a novel antiherpesvirus infection agent in the future.

The food system, the most important driver of planetary transformation, is in a deep crisis. Therefore, seeking a sustainable and socially-fair transition pathway becomes an issue of utmost priority for our own survival. The consideration of food as a commodity, a social construct that played a central role in driving this crisis, remains the uncontested narrative to lead the different transition pathways what seems rather contradictory. By exploring the normative values in the transition landscape, this paper seeks to understand how relevant is the hegemonic narrative of “food as commodity” and its alternative of “food as commons” to determine transition trajectories and food policy beliefs. Applying the Multi-level Perspective framework and developing the ill-studied “agency in transition”, this research enquired food-related professionals that belong to an online community of practice (N=95) on valuation of food dimensions and agency in food transitions to check whether the valuation of food is relevant to explain personal stances in transition. Results suggest the socially-constructed view of food as commodity is positively correlated to the gradual reforming attitude, whereas food as commons is positively correlated to the counter-hegemonic transformers regardless the self-defined position in the transition landscape (regime or niches). At personal level, there are multiple loci of resistance with counter-hegemonic attitudes in varied institutions of the regime and the innovative niches, many of them holding this discourse of food as commons. Conversely, alter-hegemonic attitudes are not positively correlated to this alternative discourse and they may inadvertently or purportedly reinforce the ‘‘neoliberal narrative’’. Food as commons, a different narrative whose rationale is explained in the paper, seems to be a relevant framework that could enrich the multiple transformative constituencies that challenge the industrial food system and therefore facilitate the convergence of movements that reject the commodification of food.