Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

Phialemonium inflatum is a useful fungus known for its ability to mineralise lignin during primary metabolism and decompose polycyclic aromatic hydrocarbons (PAHs). However, no functional genetic analysis techniques have been developed yet for this fungus, specifically in terms of transformation. In this study, we applied an Agrobacterium tumefaciens-mediated transformation (ATMT) system to P. inflatum for functional gene analysis. We generated 3,689 transformants using the binary vector pSK1044, which carried either the hygromycin B phosphotransferase (hph) gene or the enhanced green fluorescent protein (eGFP) gene to label the transformants. Southern blot analysis showed that the probability of a single copy of T-DNA insertion was approximately 50% when the co-cultivation time of fungal spores and Agrobacterium tumefaciens cells was performed at 24–36 h, whereas at 48 h, it was approximately 35.5%. Therefore, when performing gene knockout using ATMT, co-cultivation was reduced to ≤ 36 h. The resulting transformants were mitotically stable, and PCR analysis confirmed gene integration into the transformant genome. Additionally, hph and eGFP gene expressions were confirmed by PCR amplification and fluorescence microscopy. This optimised transformation system will enable functional gene analysis to study genes of interest in P. inflatum.

The Quantum-Cosmos Nexus Theory delves into the intricate web of relationships that tie together fundamental constants, cosmological properties, and the boundaries of our comprehension in the realm of physics. It unveils a profound interconnection between the gravitational constant (G), the speed of light (c), and the parameters of the observable universe. It introduces a unification equation that hints at a connection between the fundamental constants. It also introduces a new constant, , which is similar to the Planck constant but, on a large scale, signifies the ultimate unit of action or energy on a cosmic scale. With this new constant, new units similar to Planck units have been introduced. They are the equivalence of Planck units in the sense that they represent the limits of our current understanding of physics on the largest scale. The theory also shows that most of the fundamental constants of nature, including the gravitational constant (G), the speed of light (c), vacuum permittivity (ε₀) vacuum permeability (u₀), the Boltzmann constant (K_B), and the fine-structure constant (α), can be derived from these new units and Planck units. The first derived equation suggests a potential weakening of the gravitational constant over time, assuming the density remains relatively constant. Although this is a matter of speculation, it has the potential to explain observations related to dark matter. The theory also makes use of the Planck force, defining it as the maximum force on the quantum and cosmic scales. It also emphasizes that the Planck scale is not the ultimate limit and reveals our observational constraints, offering a unique perspective on the universe's fundamental workings. The Quantum-Cosmos Nexus Theory reveals how fundamental constants, cosmic dynamics, and the limits of our understanding converge, opening the door to fresh perspectives on the underlying principles of the universe.

It is universally accepted that Maxwell equations do not remain invariant under the Galilean transformation. This conflicts the principle of relativity which states that the physical law must remain invariant in the mathematical form in all inertial frames of reference. For this reason, the Lorentz transformation is invented, and the Galilean transformation is nowadays superseded by the Lorentz transformation. However, this paper challenges this widely held belief that the Maxwell equations are not invariant under the Galilean transformation. By applying the Galilean transformation to Lienard-Wiechert electromagnetic fields it is mathematically proven that the Maxwell equations indeed remain invariant under the Galilean transformation. In addition, the critical error in Lorentz's proof of Galilean non-invariance of Maxwell equations is pointed out, and it turns out that Lorentz's conclusion that Maxwell equations are not invariant under the Galilean transformation is the result of a mathematical error.

In this study, we demonstrate how the incorporation of appropriate feature engineering together with the selection of a Machine Learning (ML) algorithm that best suits the available dataset, leads to the development of a predictive model for transformation temperatures that can be applied to a wide range of shape memory alloys. We develop a gradient boosting ML surrogate model capable of predicting Martensite Start, Martensite Finish, Austenite Start, and Austenite Finish transformation temperatures with an average accuracy of more than 95% by explicitly taking care of potential distribution changes when modeling different alloy systems. We included heat treatment, rolling, extrusion processing parameters, and alloy system categorical features in the model input features to achieve more accurate and realistic results. In addition, using Shapley values, which are calculated based on the average marginal contribution of features to all possible coalitions, this study was able to gain insights into the governing features and their effect on predicted transformation temperatures, providing a unique opportunity to examine the critical parameters and features in martensite transformation temperatures.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

The aim of the research results presented in the article is to strengthen a better understanding of the processes related to the transformation of hard coal mining in Poland, in particular the preparation of employees and their representatives, as well as employers from transformed areas for the upcoming changes. In this perspective, anticipating future skills against the internal potential of entrepreneurs becomes more and more important. It is a key element that enables entrepreneurs to adapt to changes, create innovative solutions and remain competitive on the market.

The insurance sector has undergone a transformative shift with the emergence of Insurtech, integrating technological innovations into the industry. This review aims to provide a comprehensive overview of the impact of Insurtech on the insurance sector, focusing on the case study of Lemonade. By placing the study in the context of the broader insurance landscape, the review explores the significance and relevance of this transformation. The article analyzes Lemonade's unique business model and its departure from traditional insurance practices. Furthermore, it examines the implications of Lemonade's approach on the industry and the challenges it faces. Through this analysis, the review sheds light on how Insurtech and the transformation of the insurance sector are redefining insurance services and consumer experiences. The future implications of these trends for insurance companies, consumers, and the industry as a whole are also explored. In summary, this review provides valuable insights into the transformative power of Insurtech, emphasizing the importance of technological advancements and innovative approaches in shaping the future of the insurance sector.

Este artigo apresenta o processo de implementação da Hiperautomação no setor público brasileiro, especialmente no âmbito da Procuradoria Geral do Estado de Pernambuco. Devido à atual economia competitiva, a demanda por soluções inteligentes e confiáveis está aumentando. Para atender a essa necessidade, tecnologias inovadoras que abordem a complexidade inerente à transformação digital são desejáveis. Assim, as organizações públicas têm buscado aplicar a automação de processos para atender às necessidades dos cidadãos por um serviço mais eficiente e eficaz. No entanto, podemos observar que a automação pura e direta é apenas parte do processo de transformação. Algumas das razões que explicam a necessidade de ir além da automação de processos e alcançar a hiperautomação é a abundância de dados de várias fontes e tipos. Tudo deve estar dentro dos padrões legais, ressaltando que toda tecnologia deve estar alinhada com transparência e auditabilidade para ser incorporada com segurança. Para a experimentação, foi utilizado o método de pesquisa-ação com a aplicação da Hiperautomação, visando aumentar a arrecadação e a economia do Estado na Procuradoria Geral do Estado de Pernambuco.

Proposed study aims to investigate the digital transformation of Greek small and medium enterprises (SMEs), with a particular focus on their digital maturity and the strategic and organizational factors contributing to digital transformation. The research issue of digital transformation is attracting considerable interest among academics and business practicians since COVID-19 accelerated the procedure of implementing Industry’s 4.0 principles all over global economies. Quantitative research on 147 Greek SMEs revealed most important issues on how these businesses implement digital transformation, factors accelerating or decelerating the process, barriers and expected outcomes. Research enlights how SMEs face the transition to digital business and reveals the factors that can facilitate the whole process. Results can be valuable for stakeholders enabled to digital transformation process from both business and academic point of view, while there exist aspects that can contribute to policy makers / motivation developers in state’s level as well.

This paper examines the transformation of the Ukrainian stock market by analyzing daily returns from the PFTS stock index spanning 1995-2022. Segmented into sub-periods, it tests the hypothesis that the market's efficiency has grown over time. Various data properties, including persistence, volatility, normality, and resistance to anomalies, are explored using different statistical techniques and methods. Volatility, indicated by standard deviation, exhibits a general decreasing trend, suggesting a shift towards a more efficient market. Returns show no significant differences across sub-periods, except for 2005-2007. R/S analysis indicates the decrease of persistence in the market: a trend towards increased efficiency. Normality tests support a normal distribution of daily returns throughout sub-periods. An analysis of anomalies reveals the market's resilience to day-of-the-week effects, with no specific trends observed. The results suggest the absence of serious changes in data properties in the Ukrainian stock market over the time, means evolutionary processes over 25 years can’t be clearly observed. Reforms and changes have had limited impact, justifying continued reform for the market's evolution.

In an era of rapid technological advancement, Egypt stands at the crossroads of digital transformation. Our research delves into the intersection of economy and 5G technology, exploring how these forces can reshape the nation’s economic landscape. By examining the impact on GDP, we aim to guide policymakers, telecom operators, and citizens toward a more connected and prosperous future. Join us on this journey as we unravel the potential of 5G and pave the way for inclusive growth.

The present-day financial system is being influenced by the rapid development of Fintech (financial technologies), which are technologies created to improve and automate traditional forms of finance for businesses and consumers. The topic of Fintech as a financial disruptor is gaining popularity in line with the swift spread of digitalization across the banking industry, whereby this paper contributes to the field by presenting a novel bibliometric analysis of academic literature related to Fintech as a financial disruptor. The analysis is based on metadata extracted from the Scopus database through the VOSviewer and Biblioshiny software. The bibliometric analysis of 363 documents identified the most impactful sources of publication, keywords, authors, and most cited documents on the topic of Fintech as a financial disruptor. As our analysis demonstrates the number of publications on the given topic increases, defining both the interest among academia and potential for future research.

A significant amount of data is available for bench-scale fire assessments. However, there is little surrounding large-scale tests and even less so for bench-to-large scale comparisons. Large-scale tests require more material, time and preparation, making them more expensive than bench-scale assessments. However, large-scale testing is an essential component to bench-scale fire testing. The bench-scale tests must be representative of both large-scale and real fire behaviour to provide an insight into how a material or product will behave in the event of a fire during its end use application. The few existing studies reviewed in this study show more guidance and data is needed, especially on a large-scale. Unfortunately, the data that is presented is done so in an inconsistent manner using various means of presentation, statistical analysis, and modelling that doesn’t show clear comparisons between bench and large scale. Currently, no bench-scale method shows good agreement with large-scale fire behaviour. Overall, there is a need for more large-scale testing and data for direct comparisons to be made.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

The changing of banking customer preferences after Covid-19 pandemic encourages banking transformation. Neobanks emerges as innovation in banking that enter the market to compete with the incumbent banks by offering new digital experience for customer. This paper analyzes the neobanks which transformed from traditional bank, specifically its efficiency after they implement digital transformation. Efficiency is measured by using Stochastic Frontier Analysis (SFA). This study also uses Pooled Mean Group (PMG) of Panel ARDL (Autoregressive Distributed Lagged) to investigate digital transformation as one of determinants neobank’s efficiency, as well as to examine the existence of short-term and long-term relationship between digital transformation and efficiency. The SFA results show that the efficiency of the neobanks increase after they carry out digital transformation. Furthermore, from PMG Panel ARDL, it can be concluded that digital transformation is one of determinant of efficiency and there is longevity relationship between digital transformation and efficiency. In the short run, digital transformation has a significant and negative correlation with efficiency and in the long run, it has a significant positive relationship because initially digital transformation cost for operational and risk management innovation decreases the profit efficiency, but afterwards it increases the profit efficiency.

The Randić index of a graph G is the sum of (dG(u)dG(v))−1/2 over all edges uv of G, where dG(u) denotes the degree of vertex u in G. In this paper, we investigate a few graph transformations that decrease Randić index of graph. By applying those transformations, we determine the minimum Randić index on tricyclic graphs, and characterize the corresponding extremal graphs.

the process of rapidly digitalizing and transforming businesses, known as Industry 4.0, was already underway before COVID-19. However, the imposed restrictions during the pandemic significantly amplified the need and motivation for both businesses and consumers to utilize digital tools across all sectors including the sectors of bioeconomy. The agricultural and food production sectors have a predominant role in the bioeconomy of the European Union (EU), followed by wood production. These sectors make significant contributions not only to national economies but also to rural areas. Consequently, the digitalization of businesses within the bioeconomy sector not only transforms the enterprises and value chains themselves but also benefits the rural communities in which these enterprises are situated. This study aims to assess the barriers of the bioeconomy sector and ways to support digital transformation within this sector. The paper analyses bioeconomy in EU and the state of digitalisation in the EU. The empiric analysis is based on the cluster analysis of the digitalisation and R&D indicators of the EU and the AHP analysis that allows determining the digitalisation scenarios in Latvia, Lithuania and Poland carried out by four stake-holder groups - national government; advisory and extension; research and entrepreneurship. The results of the AHP indicate that experts from Lithuania and Poland preferred the scenario that suggested the self-initiative from the entrepreneurs of the sector, but experts from Latvia – prioritization of support for digital transformation using national and EU funding. The AHP results also indicate that the opinions of the national government, consulting, and research experts are more aligned throughout all three countries, but the opinion of entrepreneurs differs from these groups.

Abstract Most Asian countries like South Korea have transformed themselves from poor agrarian nations into one of the fastest-growing industrialized economies in the world. Rural transformation poses great challenges to rural people and areas, but also it also provides great opportunities for sustainable rural development. The evolution of South Korea's rural policies is embedded through the different national institutions with different sectors. Diversification of rural economic opportunities may further extend to the industries for economic development in rural regions alongside efforts to improve living. Examining the rural transformation in South Korea, mainly the rural development with land, agriculture, truism, politic,s and strategy they used that shaped the structure of the rural transformation and its activities over time and Ethiopia takes lessons is the objective of the study. Document analysis is a tool for achieving information. Ethiopia takes lessons from South Korea from the general sector of rural development to the particular agricultural development sector, rural truism development, land reform which is the core asset for the world people, health care reform, and market and trade transformation (indicates that the base for developed country development was trade reform from import to export), rural job employment transformation (which have the multidimensional impact to the development of nation) and rural political transformation are the basic areas of rural transformation in which Ethiopia focused to do. The country can grow with the integrated/ collaborative work of the stakeholders. The government of Ethiopia applying a functional regional strategy to shape the socio-economic and cultural changes of the rural people and working with civil societies and other non-governmental stakeholders must be the primary tasks

Oral squamous cell carcinoma often arises from an oral potentially malignant disorder called oral leukoplakia (OL). With this work we aimed to develop a novel data-driven predictive model based on gene expression profiles to distinguish OL patients who underwent malignant transformation from those who did not. We used the Tree Augmented Naïve (TAN) Bayes classifier to predict the posterior probability of having oral cancer given the data. 86 patients were included with a median follow-up of 7.11 years. Fifty-one patients (51/86; 59%) underwent malignant transformation. We found that 16 genes were predictors of oral cancer in patients with OL and these included SLC7A11, SPINK6, SERPINA12, VIT, ATP1B3, CST6, FLRT2, ELMOD1, AZGP1, RNASE13, DIO2, ECM1, CYP4F11, SYTL4, AKR1C1, and AKR1C3. In conclusion, we showed that Bayesian gene networks are a data-driven approach which could be used also in other predictor models in oncology.

The morphological transformation of an arched ribbon driven by torsion is a scientific problem that is connected with daily life and requires thorough analysis. An arched ribbon can achieve an instantaneous high speed through energy transformation and then return to the original shape of the structure. In this paper, based on the characteristics of the ribbon structure, the dynamic mathematical model of the arched ribbon driven by torsion is established from the Kirchhoff rod equation. The variations of the Euler angle of each point on the center line of the ribbon with the arc coordinate s and the rotation angle of the supports $\phi$ was examined. The relationship between the internal force distribution of each point in the direction of $\hat{d}_{a}$ and the material, cross-sectional properties, and rotation angle of the supports was obtained. We used ABAQUS, a nonlinear finite element analysis tool, to simulate the morphological transformations of the ribbons, verified our theory with simulation results, and reproduced the experimental results of Sano. Furthermore, we redefined the concept of the ``critical flipping point'' of Sano. In this paper, the dimensional analysis method was used to fit the simulation data. The following relationship between the critical width $ w ^{*} $, thickness h, and the radius R of the ribbon with different cross sections was obtained: $w^{*}=A\cdot R\left(h/R\right)^{0.6}$, where A is 3.19 for rectangular cross sections and 3.06 for elliptical cross sections. By analyzing the simulation data, we determined the variation behavior of the out-of-plane deflection of the center point of the ribbon with the radius R, width w, and thickness h. Our research has guiding significance for understanding and designing arched ribbons driven by torsion, and the results can be applied to problems of different scales.

Africanization of education was a major policy option in most countries in Africa upon the attainment of independence. This is because of the perceived negative effects of colonial education. The paper is an empirical sources study which discusses Africanization as an epistemicide and analyses efforts by some African states to Africanize their educational systems. It concludes that while some countries embraced the idea and actually initiated policies to Africanize their educational systems, the general picture indicates that Africanization has not succeeded in most countries due to various challenges. Such challenges are identified and recommendations made which could be significant for the revamping of the policy.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

Context: COVID-19 pandemic and the Lockdown implemented as a measure to contain the virus spread has taken a toll over the psychological well-being of the people especially the young adults, the confinement along with the environment of a highly infectious pandemic around the induvial are put under great stress.Aims: The current study aims to assess the psychological impact and perceived stress due to COVID-19 lockdown in Young Adult population of India.Settings and Design: It is a cross sectional, observational study.Methods and Material: The survey was conducted using Google forms involving snowball sampling technique which obtained 267 responses in total. (IES-R) and (PSS) scales were used for the study.Statistical analysis used: Descriptive analysis were performed on the sociodemographic parameters and the comparison of means were done by Chi-square test in SPSS Statistic 21.0 (IBM SPSS Statistics, New York, United States). Results: The mean IES-R and PSS scores obtained for the population in this study was 25.64±18.95 and 18.27±6.10 respectively. Out of the 267 respondents in total 61.4% (n=164) of them were males. Maximum of the respondents 62.54%(n=167) belonged to the age group of 18-23 with mean age being 23.14± 2.913. 92.5% of the respondents were unmarried and only 26.6% belonged to the rural part of India. Females, younger individuals were found to have higher IES-R and PSS scores. Conclusions: There is significant psychological burden and stress on the young Indian population with females and younger individuals particularly students are the most vulnerable population.

Accurate prediction of the self-propulsion performance is one of the most important factors for energy-efficient design of a ship. In general, the hydrodynamic performance of a full-scale ship could be achieved by model-scale simulation or towing tank test with extrapolations. With the development of CFD methods and computing power, directly predict ship performance with full-scale CFD is an important approach. In this article, a numerical study on the full-scale self-propulsion performance with propeller operating behind ship at model- and full-scale is presented. The study includes numerical simulations using RANS method with double-model and VOF model respectively and scale effect analysis based on overall performance, local flow fields and detailed vortex identification. Verification study on grid convergence is also performed for full-scale simulation with global and local mesh refinements. And a series of sea trail tests were performed to collect reliable data for the validation of CFD predictions. The analysis of scale effect on hull-propeller interaction shows that the difference on hull boundary layer and flow separation is the main source of scale effect on ship wake. And the results of the fluctuations of propeller thrust and torque along with circulation distribution and local flow field show that propeller’s loading is significantly higher for model-scale ship. It is suggested that the difference on vortex evolution and interaction is more pronounced and have larger effects on ship’s powering performance at model-scale than full-scale according to the simulation results. From the study on self-propulsion prediction, it could be concluded that the simplification on free surface treatment does not only affect the wave-making resistance for bare hull but also the propeller performance and propeller induced ship resistance which can produced up to 5% uncertainty to the power prediction. Roughness is another important factor in full-scale simulation because it has up to approximately 7% effect on the delivery power. As a result of validation study, the numerical simulations of full-scale ship self-propulsion shows good agreement with the sea trail data especially for cases that have considered both roughness and free surface effects. This result will largely enhance our confidence to apply full-scale simulation in the prediction of ship’s self-propulsion performance in the future ship designs.

In today’s world face detection is the most important task. Due to the chromosomes disorder sometimes a human face suffers from different abnormalities. For example, one eye is bigger than the other, cliff face, different chin-length, variation of nose length, length or width of lips are different, etc. For computer vision currently this is a challenging task to detect normal and abnormal face and facial parts from an input image. In this research paper a method is proposed that can detect normal or abnormal faces from a frontal input image. This method used Fast Fourier Transformation (FFT) and Discrete Cosine Transformation of frequency domain and spatial domain analysis to detect those faces.

Kim-Kim ([9]) studied some properties of the degenerate gamma and degenerate Laplace transformation and obtained their properties. In this paper, we define modified degenerate gamma and modified degenerate Laplace Transformation and investigate some properties and formulas related to them.

Scale drop disease virus (SDDV), a double-stranded DNA virus in the family Iridoviridae, has been reported widely in southeast Asian countries as a causative agent of scale drop syndrome (SDS) in Asian seabass. SDS have resulted in high mortality and significant economic losses to the aquaculture industry. This study demonstrated the use of metagenomic methods to investigate bacterial and viral communities present in infected fish tissues and recovering a complete genome of the causative agent named SDDV TH7_2019. Characterization of the TH7_2019 genome revealed a genome size of 131 kb with 134 putative ORFs encoding viral proteins potentially associated with host apoptosis manipulation. A comparative genome analysis showed a high degree of amino acid identity across SDDV strains, with variations in number of repeat sequences and mutations within core genes. Phylogenetic analyses indicate a close relationship among SDDV genomes. This research enhances our understanding of the genetic diversity and evolutionary relationship of SDDV, contributing valuable insights for further development of effective control strategies of SDDV.

A naked human eye can perceive objects down to a millimeter length. While lenses and microscopes have overcome this limit, the human mind still lacks perspective when navigating conventional scales (1), especially in the range that are less palpable to naked human eye (2,3). This problem is particularly acute in the context of science communication, where the conventional scale bar units facilitate little comprehension regarding the perception for factorial size differences (3). Here we aim to bridge the gap of scale factors and perspectives using a universal toolkit of objects, which can help comprehend the relative change in length dimensions up to 13 orders of magnitude difference. We further have demonstrated the use of such a universal object toolkit as a length perceptive scale by illustrating and narrating biological phenomena. The meter to picometer ‘length perceptive scale’ proposed here has the potential to cover majority of length scales present in the biological realm, and is analogous to the time compression methods widely used in explaining cosmos timeline (4). Our toolkit can also be calibrated according to the users need in their scientific communication and illustrations, which will aid the readers’ benefit in understanding the length scale perception of illustrated phenomenon.

Location-and-scale transformation of a random variable underpins normal distribution, but it is however fundamentally incorrect for scale estimation such as relative dispersion. In this paper, a parametrized alternative to a normal distribution, called scaloc-normal distribution, is proposed that efficiently works and is fundamentally correct with absolute and relative dispersion estimators. The Monte Carlos simulation experiment was used to generate a total of 600,000 artificial datasets in 600 different simulation scenarios from loc-normal (normal) and scaloc-normal distributions. The absolute and relative dispersion were estimated and compared from the two distributions. The results show that scaloc-normal distribution is a good parametrized alternative to loc-normal distribution, fundamentally correct and efficient with both standard deviation and coefficient of variation. The key statistical advancement from loc-normal to scaloc-normal distribution is its fundamental correctness (i.e., scale-invariant property) with an efficient relative estimator of dispersion (i.e., coefficient of variation). Parametrically, the loc-normal and scaloc-normal distributions are very different, but both have linear transformations.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

Blockchain technology (BCT) has the potential for sustainable development, enhancing business efficiency, reducing costs, and strengthening data security. Despite its potential, adoption among small and medium-sized enterprises (SMEs) is low due to the need for significant changes in technology infrastructure and the challenge of interoperability. A cross-sectional survey was done with 226 Hong Kong SMEs. The PLS-SEM results highlighted favorable transformation conditions as the most critical factor for SMEs considering the adoption of BCT. These conditions address both internal and external readiness for adopting the disruptive strategy. Other contributing factors to BCT adoption include trust in BCT developers, perceived usefulness and ease of use, government support, and perceived security. The research results contributed to the literature on disruptive technology acceptance, adoption, transformation conditions, technology readiness, and SMEs’ technology adoption. Government-supported policies and initiatives can promote BCT adoption, including educational programs, case studies, and resources for readiness. Financial support and regulatory frameworks can further encourage adoption. BCT developers can demonstrate the value of their systems, effectively communicate potential ROI and cost savings, and provide user-friendly interfaces to increase SMEs’ intention to adopt BCT.

Reactions of Co(OAc)24H2O, N‚N'-bis(3-pyridylmethyl)oxalamide (L) and 4,4’-sulfonyldibenzoic acid (H2SDA) afforded four coordination polymers with the same mixed ligands, {[Co(L)(SDA)(H2O)2]·H2O·CH3OH}n, 1, {[Co(L)0.5(SDA)]·2H2O·0.5L}n, 2, {[Co(L)1.5(SDA)(H2O)]·H2O}n, 3, and {[Co2(L)1.5(SDA)2(H2O)2]·4H2O}n, 4, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 are 2D layers, revealing the topologies of sql, 2,6L1, (4,4)Ia and 6L12, respectively, and demonstrating that the metal to ligand ratio, solvent system and reaction temperature are important in determining the structural diversity. Immersion of these complexes into various solvents show that the structural types govern the chemical stabilities of 1 – 4. Reversible structural transformation can be shown for complexes 1 and 2 upon solvent removal and adsorption, while those of 3 and 4 are irreversible.

Various implementations of the Move with Interleaving transform are discussed in this paper, with the transformation itself explained briefly at first. The transform has an expected time complexity of O(n), where n represents the length of the sequence being transformed. The importance of implementation also grows as the sequences become longer. The paper explains three different implementations: the first uses the standard vector, the second employs a lookup table, and the third utilises a dynamic linked list with a pool of released records. The experiments were conducted on 32 greyscale raster images of various contexts and sizes. All three solutions were implemented in both C++ and Java, and then executed on three different platforms: a personal computer running MS Windows and Linux, and a Raspberry Pi 2 with Linux. The implementation based on the dynamic linked list was the fastest, and outperformed the vector-based implementation by more than 1800%. While direct comparisons between results on the Raspberry Pi and those on the modern personal computer may not be straightforward, a consistent pattern prevails: the dynamic linked list implementation outperformed the other two consistently, and the C++ code was faster than the code written in Java. The difference was most evident on the Raspberry Pi.

Mesenchymal stromal cells (MSCs) are a subset of heterogeneous non-hematopoietic fibro-blast-like cells which play important roles in tissue repair, inflammation, and immune modula-tion. MSCs residing in the bone marrow microenvironment (BMME) functionally interact with hematopoietic stem progenitor cells regulating hematopoiesis. However, MSCs have also emerged in the last years as key regulator of tumor microenvironment. Indeed, they are now con-sidered as active players in the pathophysiology of hematologic malignancies rather than passive by-standers in hematopoietic microenvironment. Once the malignant event occurs, the BMME acquires cellular, molecular, and epigenetic abnormalities affecting tumor growth and progres-sion. In this context, MSC behavior is affected by signals coming from cancer cells. Furthermore, it has been showed that stromal cells themselves play a major role in several hematological malig-nancies’ pathogenesis. This bidirectional crosstalk creates a functional tumor niche unit wherein tumor cells acquire a selective advantage over their normal counterpart and are protected from drug treatment. It is therefore of critical importance to unveil the underlying mechanisms which activate a protumor phenotype of MSCs for defining unmasked vulnerabilities of hematological cancer cells which could be pharmacologically exploited to disrupt the tumor/MSCs coupling. The present review will focus on the current knowledge about MSC dysfunction mechanisms in the BMME of hematological cancers, sustaining tumor growth, immune escape, and cancer pro-gression.

The cubic B2 to monoclinic B19’ martensitic transformation in NiTi shape memory alloys proceeds by the nucleation and propagation of habit plane interfaces that remain undistorted and unrotated by the transformation. Due to incompatibility of austenite and martensite lattices in NiTi, the interfaces form between austenite and twinned martensite as described by Phenomenological Theory of Martensite Crystallography (PTMC). This have been assumed also for stress-induced martensitic transformation where, however, interfaces with single martensite variant have been frequently reported. On this account, we propose a different solution of strain compatibile habit planes by considering the effect of elastic deformation of both lattices due to external stress. Using modified PTMC theory, we evaluate the magnitudes and orientations of the critical uniaxial stress in tension and compression for which strain compatible habit plane interfaces with a single variant of martensite can form. The calculated stress is too high, but considering the pre-transformation softening of the C’ elastic constant for the {110}A⟨110⟩A austenite shear mode, the critical stress decreases down to 500 MPa. For such situation, we analyse orientation dependence and tension-compression asymmetry of required C’ softening, and the orientations of strain compatible habit planes that are compared with available experimental results. All calculations, including source code and interactive graphs, are available for download.

Non-rigid registration presents a significant challenge in the domain of point cloud processing. The general objective is to model complex non-rigid deformations between two or more overlapping point clouds. Applications are diverse and span multiple research fields, including registration of topographic data, scene flow estimation, and dynamic shape reconstruction. To provide context, we begin with a general introduction to the topic of point cloud registration, including a categorization of methods. Next, we introduce a general mathematical formulation for point cloud registration and extend it to address non-rigid registration. A detailed discussion and categorization of existing approaches to non-rigid registration follows. We then introduce our own method where the usage of piece-wise tricubic polynomials for modeling non-rigid deformations is proposed. Our method offers several advantages over existing methods. These advantages include easy control of flexibility through a small number of intuitive tuning parameters, a closed-form optimization solution, and an efficient transformation of huge point clouds. We demonstrate our method through multiple examples that cover a broad range of applications, with a focus on remote sensing applications - namely, the registration of Airborne Laser Scanning (ALS), Mobile Laser Scanning (MLS), and Terrestrial Laser Scanning (TLS) point clouds. The implementation of our algorithms is open source and can be found on GitHub.

ABSTRACT Education is the most important instrument in human life because education can increase human dignity. In addition, education can also be a benchmark for human quality and an example of the progress of a nation. The history of education in Indonesia has evolved from the colonial era to the digital era. These developments have influenced government policies in every era. In the 21st century, the development of education in Indonesia is starting to show progress. This is because it is supported by the rapid growth of information and technology. This research article aims to analyze the educational policies carried out by the government from the colonial era to the digital era to be used as evaluation material at this time so that in the future education in Indonesia is even better. To achieve this goal, this research focuses on the question of how is the transformation of education in Indonesia from the colonial era to the digital era? and what is the paradigm of education in Indonesia when viewed from a historical perspective?. The research method used is the Literature Review method from 27 sources in journal articles, websites, and data reports for 2019-2021. The results of this study found that changes in the Indonesian education system from time to time have a positive influence on the progress of the Indonesian nation. The development of education in Indonesia also has an impact on increasing the Human Development Index (HDI). This shows that the quality of Indonesian society is increasing. Based on the results obtained, it is hoped that it can provide information about the transformation of education in Indonesia from the colonial era to the digital era from a historical perspective. This article is suitable as a reference source for education observers in Indonesia to know the history of education and its policies from the colonial era to the digital era and useful for academics to know the history of education in Indonesia. This research has limitations, namely this research is only limited to the development of education in Indonesia from the colonial era to the digital era and the paradigm of education development in Indonesia from a historical perspective.

We consider mixture experiments in which the proportions of the components must be non-negative and their sum must equal one. Thus, the experimental region for a mixture of components is a simplex. Li and Zhang (2017) made the conjecture that the pseudo component transformation of the lattice points in the simplex has a special property. In this paper, we show that this conjecture is not true in general. Furthermore, we refine this conjecture and prove the refined conjecture.

In this study, we discuss the theoretical studies on the creation of artificial magnetic monopole, and new electromagnetic equations. Employing Lorentz transformation, radial electrostatic fields, and a stationary wave derived from a superconducting loop, we demonstrate the existence of a magnetic monopole whereby the divergence of the magnetic field is not zero. We develop a device wherein a condenser provides electrostatic fields along the radial direction to the superconducting loop and discuss the nodes of the resulting stationary wave along the superconducting loop. We employ the Lorentz transformation with respect to the vector and electrostatic potentials. Then, because the nodes have no three-dimensional vector potential and have zero magnetic field rotation, the conserved energy is converted into new form that is associated with the magnetic field potential to yield the Lorentz transformation. As a result, we derived the relationship between the electric and the magnetic fields. This dependent relationship involves the exchange of the distribution characteristics of the static electric and static magnetic fields, and new electromagnetic equations of both electric and magnetic fields are obtained. We also analyzed the magnetic field from the magnetic monopole whose result assists the theory.

Jakarta belongs to the cities with the highest flood risk in the world. Its flood hazard is driven by land subsidence, soil sealing, changes in river discharge and increasingly sea level rise. As all of these trends are set to continue, Jakarta’s flood hazard is expected to intensify in the future. Designing and implementing risk reduction and adaption measures is therefore of utmost importance. Against the background, the paper draws on a discourse analysis and original empirical household survey data to review and evaluate current adaptation measures and to analyze in how far they describe a path that is transformative from previous risk reduction approaches. The results show that the focus is clearly on engineering solutions, foremost in the Giant Sea Wall project. The project is likely to transform the city’s flood hydrology. However, it cements rather than transforms the current risk management paradigm which gravitates around the goal of controlling flood symptoms, rather than addressing their anthropogenic root causes. The results also show that the planned measures are heavily contested due to concerns about ecological impacts, social costs, distributional justice, public participation and long-term effectiveness. On the outlook, the results therefore suggest that the more the flood hazard will intensify in the future, the deeper a societal debate will be needed about the desired pathway in flood risk reduction and overall development planning – particularly with regards to the accepted level of transformation, such as partial retreat from the most flood-affected areas.

The pursuit of human-centered, sustainable and resilient production is shaping a future-oriented approach to manufacturing processes in the context of Industry 5.0. How can such production be implemented? For this purpose, this article analyses the effects of the developed Dresden Model of Adaptability on the integration of holistic sustainability. The focus is on investigating the promotion of economic, environmental and social sustainability goals in terms of the 17 Sustainable Development Goals as well as analysing strategies to increase resilience to changing environmental conditions. A human-centered perspective is considered. The model proves to be a holistic approach that drives sustainable development of the production system through the comprehensive integration of human, technology, and organisational structures.

The theory of special relativity has reexamined and reconstructed the concepts of space and time, which are indispensable for describing physical laws, consequently instigating a major revolution in physics in general. Although the correctness of the special theory of relativity has been con-firmed by many observations and experiments, it is unclear why the "principle of relativity" and the "principle of the constant speed of light," which form the basis of the idea, are valid. Moreo-ver, although special relativity has advanced our understanding of time, our understanding of the fundamental question, "What is time?" is still limited. The theory of special relativity regards space as a four-dimensional construct consisting of one-dimensional time and three-dimensional space. This paper proposes an alternative framework, wherein real space is uniform and isotropic four-dimensional space, and elementary particles are waves that propagate through this four-dimensional space at a constant speed. This new perspective provides evidence to support two of Einstein’s key principles—the "principle of relativity" and the "principle of the constant speed of light." Furthermore, this model clarifies what time is and why time flows at a constant rate from the past to the future.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

California has experienced a surge in wildfires, prompting research into contributing factors, including weather and climate conditions. This study investigates the complex, multiscale interactions between large-scale climate patterns, such as the Boreal Summer Intraseasonal Oscillation (BSISO), El Niño Southern Oscillation (ENSO), and the Pacific Decadal Oscillation (PDO), and their influence on moisture and temperature fluctuations, and wildfire dynamics in California. The combined impacts of PDO and BSISO on intraseasonal fire weather changes, the interplay between Fire Weather Index (FWI), relative humidity, vapor pressure deficit (VPD), and temperature in assessing wildfire risks, and geographical variations in the relationship between FWI and climatic factors within California are examined. The study employs a multi-pronged approach, analyzing wildfire frequency and burned areas alongside climate patterns and atmospheric conditions. Findings reveal significant variability in wildfire activity across different climate conditions, with heightened risks during specific BSISO phases, La-Niña, and cool PDO. The influence of BSISO varies depending on its interaction with PDO. Temperature, relative humidity, and VPD show strong predictive significance for wildfire risks, with significant relationships between FWI and temperature in elevated regions (correlation, r > 0.7, p ≤ 0.05) and FWI and relative humidity along the Sierra Nevada Mountains (r ≤ -0.7, p ≤ 0.05).

This study is dedicated to understanding and simulating the mechanical properties of concrete, with a specific focus on the mesoscopic scale. Investigating concrete at this level involves examining its composition as a heterogeneous amalgamation comprising mortar, aggregates, and the interfacial transition zone (ITZ). Such an approach provides a detailed examination of the material's behavior and attributes. Numerical models are utilized, leveraging the finite element method (FEM), to examine the behavior of concrete. The study employs MATLAB programming to develop three-dimensional models, subsequently subjected to FEM analysis. Various mesoscopic Representative Volume Elements (RVEs) are formulated, encompassing varied shapes and dimensions. The MATLAB framework generates input files for numerical FEM simulations, replicating compression strength tests. As complexity increases with the inclusion of the ITZ, prismatic RVEs are developed. The proposed mesoscopic model establishes a foundational framework for a numerical simulation methodology tailored to laboratory compression tests. It provides detailed insights into concrete behavior, elucidating deformation, and fracture mechanisms. Although not a complete substitute for experimental methods, these models offer a cost-effective and expeditious alternative, pinpointing vulnerable areas and exploring the implications of additional materials on concrete behavior. Experimental data and virtual tests pave the way for mitigating carbon footprint and improving concrete sustainability.

Scales are widely used in many agricultural applications, ranging from weighing crops at harvest to determine crop yields to regularly weighing animals to determine growth rate. In agricultural research applications, there is a long history of measuring crop water use (evapotranspiration) using a particular type of scale called weighing lysimeters. Typically, weighing lysimeters require very accurate data logging systems that tend to be expensive. Recent developments in open-source technologies, such as micro-controllers and Internet of Things (IoT) platforms, created opportunities for developing effective and affordable ways to monitor crop water use and transmit the data to the Internet in near real-time. Therefore, this study aimed to create an affordable Internet of Things (IoT) scale system to measure crop evapotranspiration. A scale system to monitor crop evapotranspiration was developed consisting of an Arduino-compatible microcontroller with cell phone communication, electronic load cells, an Inter-Integrated Circuit (I2C) multiplexer, and analog-to-digital converters (ADC). The system was powered by a LiPo battery, charged by a small (6 W) solar panel. The IoT scale system was programmed to collect data from the load cells at regular time intervals and send the data to the ThingSpeak.com IoT platform. The system performed successfully during indoor and outdoor experiments conducted in 2023 at the Clemson University Edisto Research and Education Center, Blackville, SC. The results from the experiments showed that the IoT scale system could accurately measure crop evapotranspiration using the weighing lysimeter technique.

A new pterygosomatid mite species, Neopterygosoma robertmertensi sp. n. (Acariformes: Pterygosomatidae) was collected from two specimens of Liolaemus robertmertensi (Liolaemidae) from Argentina. This new species is described based on active stages: adults (female and male) and juveniles (deutonymphs, protonymphs, larvae), and quiescent stages (nymphchrysalis, deutochrysalis and imagochrysalis). The changes in morphological characters during the ontogeny of N. robertmertensi have been analyzed in detail. A difference in larval sex morphology was observed for the first time in the family Pterygosomatidae (female larvae differ from male larvae by the shape and size of the idiosoma and position of the genital area). This new mite species is most similar to N. cyanogasteri but can be distinguished by the presence of different leg chaetotaxy patterns of genua IV and femora IV, four to six genital setae, three to five dorsomedial setae and two to three ventromedial setae. Phylogenetic analysis was conducted based on 120 morphological characters of all Neopterygosoma spp. and four outgroup species using the maximum parsimony approach. The results indicated that this species is nested within mites of the chilensis group of Neopterygosoma associated with host species of the section chiliensis of Liolaemus s. str. An updated diagnosis of the chilensis group of Neopterygosoma and an identification key for all species of this genus has been provided.

Our work uses Iterative Boltzmann Inversion (IBI) to study the coarse-grained interaction between 20 amino acids and the representative carbon nanotube CNT55L3. IBI is a multi-scale simulation method that has attracted the attention of many researchers in recent years. It can effectively modify the coarse-grained model derived from the Potential of Mean Force (PMF). IBI is based on the distribution result obtained by All-Atom molecular dynamics simulation, that is, the target distribution function, the PMF potential energy is extracted, and then the initial potential energy extracted by the PMF is used to perform simulation iterations using IBI. Our research results have gone through more than 100 iterations, and finally, the distribution obtained by coarse-grained molecular simulation (CGMD) can effectively overlap with the results of all-atom molecular dynamics simulation (AAMD). In addition, our work lays the foundation for the study of force fields for the simulation of the coarse-graining of super-large proteins and other important nanoparticles.

Image segmentation and classification still represent an active area of research since no universal solution can be identified. Established segmentation algorithms like thresholding are problem specific, treat well the easy cases and mostly relied on single parameter i.e intensity. Machine learning approaches offer alternatives where predefined features are combined into different classifiers. On the other hand, the outcome of machine learning is only as good as the underlying feature space. Differential geometry can substantially improve the outcome of machine learning since it can enrich the underlying feature space with new geometrical objects, called invariants. In this way, the geometrical features form a high-dimensional feature space for each pixel, where original objects can be resolved. Alternatives based on the geometry of the image scale-invariant interest points have been exploited successfully in the field of computer vision. Here, we integrate geometrical feature extraction based on signal processing, machine learning, and input relying on domain knowledge. The approach is exemplified on the ISBI 2012 image segmentation challenge data set. As a second application, we demonstrate powerful image classification functionality based on the same principles, which was applied to the HeLa and HEp-2 data sets. Obtained results demonstrate that feature space enrichment properly balanced with feature selection functionality can achieve performance comparable to deep learning approaches.

We are using information from a paper deriving a Lorentz-violating energy-momentum relation entailing an exact mo_mentum cutof as stated by G. Salesi . Salesi in his work allegedly defines Pre Planckian physics, whereas we restrict our given application to GW generation and DE formation in the first 10^-39s to 10^-33s or so seconds in the early universe. This procedure is inacted due to an earlier work whereas referees exhibited puzzlement as to the physical mechanism for release of Gravitons in the very early universe. The calculation is meant to be complementary to work done in the Book “Dark Energy” by M. Li, X-D. Li, and Y. Wang, and also a calculation for Black hole destruction as outlined by Karen Freeze, et. al. The GW generation will be when there is sufficient early universe density so as to break apart Relic Black holes but we claim that this destruction is directly linked to a Lorentz violating energy-momentum G. Salesi derived, which we adopt, with a mass m added in the G. Salesi energy momentum results proportional to a tiny graviton mass, times the number of gravitons in the first 10^-43 seconds

With continued technological innovation in the fields of mixed reality (MR), wearable-type MR devices, such as helmets, have been released and are frequently used in various fields, such as entertainment, training, and education. However, because each product has different parts and specifications in terms of the design and manufacturing process, users feel that the virtual objects overlaying real environments in MR are visualized differently depending on the scale and color used by the MR device. In this paper, we compare the effect of scale and color parameters on users’ perception in using different types of MR devices to improve MR experience. We conducted two experiments (scale and color), and our experimental study showed that the subjects who participated in the scale perception experiment clearly tended to underestimate virtual objects, compared with real objects, and overestimate color in MR environments. [MM1]Please confirm meaning.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

The range of rating instruments in depression measurement and the depth of their analytical relevance constitutes a major development in this psychiatric and psychotherapeutic field of mental health. Though the competition is acute amongst these various instruments, the results for the public have been outstandingly positive. A depression rating scale is essentially a psychiatric measuring instrument utilized in the identification and ranking of depression severity within the patient. The scale provides the practitioner, psychiatrist or psychotherapist, with sufficient information to assess the severity of the depression plotted on the scale. Not used as a “diagnostic tool” itself, nevertheless, the depression rating scale does function as an effective device for designating and assigning a behavioral score which may, then, be used in establishing the severity of depression of value in the designation of a diagnosis and treatment formula. In this paper, we will take a close look at the leading depression rating scales and briefly summarize their scope of assessment value in rating depression.

Organisational performance is a major concern for any company wishing to remain competitive in today's market. This is why many companies have begun to integrate digital technologies into their management systems. The aim of this article is to determine the contribution of digitisation to organisational performance management, through observations and analysis of a single case study of a company that has adopted a digital transformation project. It emerged that digital transformation makes a significant contribution to organisational performance management. However, this transformation requires significant support and adaptation of skills and organisational structures.

The risk of malignant transformation of induced pluripotent stem cells (iPSC)-derived cells in response to DNA damage is a potential concern as the tumor suppressor genes TP53 and CDKN2A are transiently inactivated during reprogramming. Here, we evaluated the integrity of cellular senescence pathways and DNA double-strand break (DSB) repair in iPSC-derived human fibroblasts (i-HF) compared to their parental skin fibroblasts (HF). Using a variety of functional assays, we show that the capacity of i-HF to enter senescence and repair DSB is not compromised after damage induced by ionizing radiation (IR) or overexpression of H-RASV12. Still, i-HF lines are transcriptionally different from their parental lines, showing enhanced metabolic activity and higher expression of p53-related effector genes. As a result, i-HF lines generally exhibit increased sensitivity to various stresses, have an elevated senescence-associated secretory phenotype (SASP) and cannot be immortalized unless p53 expression is knocked down. In conclusion, while our results suggest that i-HF are not at a greater risk of transformation, their overall hyperactivation of senescence pathways may impede their function as a cell therapy product.

High-resolution wave measurements at intermediate water depth are required to improve coastal impact modeling. Specifically, such data sets are desired to calibrate and validate models, and broaden the insight on the boundary conditions that force models. Here, we present a wave data set collected in the North Sea at three stations in intermediate water depth (6-14~m) during the 2021/2022 storm season as part of the RealDune/REFLEX experiments. Continuous measurements of synchronized surface elevation, velocity and pressure were recorded at 2-4~Hz by Acoustic Doppler Profilers and an Acoustic Doppler Velocimeter for a 5~month duration. Time series were quality-controlled, directional-frequency energy spectra were calculated, and common bulk parameters were derived. Measured wave conditions vary from calm to energetic with 0.1-5.0~m sea-swell wave height, 5-16~s mean wave period and W-NNW direction. Nine storms, i.e. wave height beyond 2.5~m for at least six hours, were recorded including the triple storms Dudley, Eunice and Franklin. This unique data set can be used to investigate wave transformation, wave nonlinearity and wave directionality for higher and lower frequencies (e.g. sea-swell and infragravity waves) to compare with theoretical and empirical descriptions. Furthermore, the data can serve to force, calibrate and validate models during storm conditions.

A rapid synthesis of chiral sulfoxide-functionalized meta-terphenyl derivatives by a 2,5-[C4+C2] ring transformation reaction of pyrylium salts with in-situ generated enantio-merically pure .alpha.-sulfinylacetaldehydes is described. This synthetic method demonstrates for the first time the use of .alpha.-sulfinylacetaldehydes in a reaction sequence initiated by nu-cleophilic attack of pyrylium salts by .alpha.-sulfinylcarbanions to generate chiral aromatic systems. The method presented shows broad applicability starting with various methyl sulfoxides and a number of functionalized pyrylium salts, furnishing meta-terphenyls with complex substitution patterns from readily accessible starting compounds.

The integration of automation and process optimization within the context of AI-powered digital transformation has emerged as a pivotal strategy for organizations aiming to enhance efficiency, foster innovation, and competitiveness. This paper is devoted to present innovative contribution by providing a comprehensive structured roadmap that outlines the foundational principles necessary for the successful integration of automation and optimizing processes within the con-text of emerging AI technologies. The paper introduce a cohesive framework consisting of es-sential key pillars: Data-Driven Insights, Seamless Automation, Adaptive Learning and Contin-uous Improvement, Human-Centric Collaboration, Ethical and Responsible AI, Strategic Align-ment, Scalability, and Innovation. These pillars function as guiding principles to navigate the in-tricate landscape of automation-driven initiatives within AI-powered digital transformation. By embracing these pillars, organizations can embark on a transformative journey that maximizes the potential of automation, fosters innovation, and positions them as leaders in the ever-evolving landscape of AI-driven business operations.

Image encryption based on chaotic maps is an important way to ensure the secure communication of digital multimedia on the Internet. To improve the encryption performance and security of image encryption systems, a new image encryption algorithm is proposed by employing a compound chaotic map and random cyclic shift. Firstly, an improved Hybrid chaotic system is designed by coupling Logistic, ICMIC, Tent, and Chebyshev maps (HLITC). Comparison tests with previous chaotic maps in terms of chaotic trajectory, Lyapunov exponent, and Kolmogorov entropy illustrate the new hybrid chaotic map has better chaotic performance. Then the proposed HLITC chaotic system is used to develop a new chaotic image encryption scheme with the double cyclic shift. The improved HLITC chaotic system is performed to generate key sequences used in the image scrambling and diffusion stage. The spiral transformation controlled by chaotic sequence is used to scramble the pixels of the plaintext image, while the XOR operation based on a chaotic map is used for pixel diffusion. Extensive experiments of statistical analysis, key sensitivity, and keyspace analysis are conducted. Experimental results show the proposed encryption scheme has good robustness against brute force attacks, statistical attacks, and differential attacks, and is more effective than many existing chaotic image encryption algorithms.

At present, countries around the world adopt digital strategy, so that enterprises apply digital technology, digital supply chain, blockchain, and a series of digital measures to enhance their competitiveness. By analyzing the relationship between digital transformation of manufacturing export enterprises, and their business performance and export performance, this paper focused on the current situation and existing problems of digital transformation of manufacturing export enterprises in China. Based on the Resource Based View theory and Trade theory, the impact of digital transformation of enterprises performance, proposing hypotheses, and building regression models were explored. With the samples of 1007 listed companies in Shanghai and Shenzhen Stock markets from 2012 to 2019, the regression analysis, intermediate effect test, robustness test, stage lag, and heterogeneity analysis were conducted. The results shew that: (1) Listed manufacturing export enterprises carried out digital transformation, which had a significantly positive effect on enterprise performance; (2) It was found that digital transformation could improve enterprise performance by reducing costs, improving R&D intensity and improving human resources etc. (3) According to the fractal analysis, non-state-owned enterprises had more positive effects on enterprise performance, and digital transformation of manufacturing export enterprises in developed areas had a more significant impact on enterprise performance. Finally, according to the empirical results, relevant suggestions for digital transformation were provided.

This study investigates the multifaceted aspects of 21st century teaching and identifies gaps in current educational practices. The researcher employed a qualitative approach, utilizing interviews, observations, and document analysis. Grounded in a theoretical framework emphasizing student-centered pedagogy, technology integration, and innovative instructional strategies, the study involved a diverse sample of 30 participants, including teachers, students, and administrators. Rigorous measures were implemented to ensure validity and reliability, such as researcher triangulation and member checking. The findings revealed significant gaps in areas such as student engagement, digital literacy, and pedagogical innovation. These findings are discussed in relation to existing literature, highlighting the implications for educational practice and the urgent need for educational transformation. The study's limitations include the small sample size and its focus on a specific educational context. Future research should explore the identified gaps using different methodologies and extend the investigation to other educational settings. The study contributes to the growing body of knowledge on 21st century teaching, providing valuable insights for educators, policymakers, and researchers aiming to promote effective and transformative teaching practices in the modern era.

The search for growth and sustainability in any organization largely depends on its ability to carry out digital transformation and agility processes. These processes are essential to adapt to an increasingly changing and competitive business environment, allowing companies to be more efficient and effective in creating an unbreakable bond with their customers. This manuscript addresses the importance of detecting and eliminating anti-patterns in organizational culture for a successful digital and agile transformation. During the early stages of the transformation process, prejudices and paradigms rooted in the organization can become an obstacle to change. The goal of this writing is to offer a practical guide for leaders and teams in organizations seeking successful cultural transformation. Effective strategies are proposed to overcome the challenges faced by organizations during this early stage. In summary, the key steps to be followed in the initial stages of digital transformation with agility are described, including the importance of establishing strong leadership, defining a clear vision and scope of the transformational process, among others. A set of recommendations will be provided to overcome recurring anti-patterns, such as lack of stakeholder participation and commitment, lack of proper planning, and confusion of roles and responsibilities.

First came the digital banks without offices, and then the “fintech” companies that combined technology and finance to achieve greater efficiency and new business models. Later was the turn of transport and logistics, understood as the sector whose economic activities derived from the transport of people and goods, while on the one hand, it has had a new spring thanks to factors such as online sales. Then, perhaps catalyzed by the pandemic scenario, the turn has reached education, where years ago was only a complement of traditional education, now is a central part with multiple modern methodologies. Numerous studies exist about using or implementing these e-learning procedures, but technical analysis is barely found in references. This work aims to analyze the digital transformation of the main sectors of our society, including finances, transport, and education, together with several examples of how technology was helping to fight the pandemic scenario.

Digital transformation of companies is often referred to as a future track and a strategic path towards ensuring the survival and sustainability of companies. In this paper, we aim to outline this transformation process in Tunisian companies and identify its driving factors and finally explain its key success factors. To this end, we examine a sample of 70 companies operating in all economic sectors. The results indicate that such a digital strategy has a significant and a positive effect on the success of digital transformation of companies. Leadership has an effect at a low level of digital maturity. On the other hand, corporate culture does not have a significant effect on digital transformation. These results contribute to explaining this emerging phenomenon by focusing on the driving factors as well as the factors that contribute to its success.

Brain tumors are abnormal cells growth in the brain tissues that can be cancerous, or not. In any case, they could be a very aggressive disease that should be detected as early as possible. Usually, magnetic resonance imaging (MRI) is the main tool commonly adopted by neurologists and radiologists to identify and classify any possible anomalies present in the brain anatomy. In the present work, an automatic unsupervised method called Z2-$\gamma$, based on the use of adaptive finite-elements and suitable pre-processing and post-processing techniques, is introduced. In particular, the proposed methodology is able to automatically classify whether a given MR image represents a healthy or a diseased brain and in this latter case, is able to locate the tumor area.

The new SARS-CoV-2 coronavirus has brought with it an increase in the use of digital platforms and an exponential increase in the number of scientific papers worldwide. The purpose of this study is to show a global overview of the digital transformation from 1975 to the present (2021). The main collection of the Web of Science database was used to retrieve global scientific production on digital transformation. Bibliometric indicators of production, visibility, impact, and collaboration were analyzed to assess research progress on the topic. The results show that digital transformation is a construct of recent development, increasingly relevant and transdisciplinary, with a clear growth after the declaration of the global COVID-19 pandemic.

Seismic imaging is the main technology used for subsurface hydrocarbon prospection. It~provides an image of the subsurface using the same principles as ultrasound medical imaging. As for any data acquired through hydrophones (pressure sensors) and/or geophones (velocity/acceleration sensors), the raw seismic data are heavily contaminated with noise and unwanted reflections that need to be removed before further processing. Therefore, the noise attenuation is done at an early stage and often while acquiring the data. Quality control (QC) is mandatory to give confidence in the denoising process and to ensure that a costly data re-acquisition is not needed. QC is done manually by humans and comprises a major portion of the cost of a typical seismic processing project. It is therefore advantageous to automate this process to improve cost and efficiency. Here, we propose a supervised learning approach to build an automatic QC system. The~QC system is an attribute-based classifier that is trained to classify three types of filtering (mild = under filtering, noise remaining in the data; optimal = good filtering; harsh = over filtering, the signal is distorted). The attributes are computed from the data and represent geophysical and statistical measures of the quality of the filtering. The system is tested on a full-scale survey (9000 km²) to QC the results of the swell noise attenuation process in marine seismic data.

Seismic imaging is the main technology used for subsurface hydrocarbon prospection. It provides an image of the subsurface using the same principles as ultrasound medical imaging. It is based on emitting a sound (pressure) wave through the subsurface and recording the reflected echoes using hydrophones (pressure sensors) and/or geophones (velocity/acceleration sensors). Contrary to medical imaging, which is done in real time, subsurface seismic imaging is an offline process that involves a huge volume of data and needs considerable computing power. The raw seismic data are heavily contaminated with noise and unwanted reflections that need to be removed before further processing. Therefore, the noise attenuation is done at an early stage and often while acquiring the data. Quality control (QC) is mandatory to give confidence in the denoising process and to ensure that a costly data re-acquisition is not needed. QC is done manually by humans and comprises a major portion of the cost of a typical seismic processing project. It is therefore advantageous to automate this process to improve cost and efficiency. Here, we propose a supervised learning approach to build an automatic QC system. The QC system is an attribute-based classifier that is trained to classify three types of filtering (mild = underfiltering, noise remaining in the data; optimal = good filtering; harsh = overfiltering, the signal is distorted). The attributes are computed from the data and represent geophysical and statistical measures of the quality of the filtering. The system is tested on a full-scale survey (9000 km2) to QC the results of the swell noise attenuation process in marine seismic data. The results are encouraging and helped identify localized issues that were difficult for a human to spot.

In personalized healthcare, an ecosystem for the manipulation of reliable and safe private data should be orchestrated. This paper describes a first approach for the generation of fake electrocardiograms (ECGs) based on Generative Adversarial Networks (GANs) with the objective of anonymizing users’ information for privacy issues. This is intended to create valuable data that can be used both, in educational and research areas, while avoiding the risk of a sensitive data leakage. As GANs are mainly exploited on images and video frames, we are proposing general raw data processing after transformation into an image, so it can be managed through a GAN, then decoded back to the original data domain. The feasibility of our transformation and processing hypothesis is primarily demonstrated. Next, from the proposed procedure, main drawbacks for each step in the procedure are addressed for the particular case of ECGs. Hence, a novel research pathway on health data anonymization using GANs is opened and further straightforward developments are expected.

The study sought to gauge the impact of COVID-19 pandemic in unleashing digital transformation in the education sector in South Africa. In order to gauge the impact, the study tracked the rate at which the 4IR tools were used by various institutions during the COVID-19 lockdown. Data were obtained from secondary sources, mainly newspaper articles, magazines and peer-reviewed journals. The findings are that, in South Africa, during the lockdown, a variety of 4IR tools were unleashed from primary education to higher and tertiary education where educational activities switched to remote learning (online learning). These observations point to the fact that South Africa generally has, some pockets of excellence to drive the education sector into the 4IR, which has the potential to increase access. Access to education, particularly at a higher education level, has always been a challenge due to a limited number of spaces available. Much as this pandemic has brought with it massive human suffering across the globe, there is an opportunity to assess successes and failures of deployed technologies, costs associated with them, and scaling these technologies to improve access.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

A field experiment was conducted in Ninghe, Tianjin, China, using 15N isotope method to evaluate the application of organic fertilizer on N distribution patterns of labelled and unlabeled N fertilizer, ammonium sulfate -15N uptake by rice, N use efficiency (NUE), and the fate of (15NH4)2SO4 applied. The experiment included eight treatments: CK-N (control + no-duck), CK-D (control + ducks), CF-N (chemical fertilizer + no-ducks), CF-D (chemical fertilizer + ducks), CM-N (chemical fertilizer + organic fertilizer + no-ducks), CM-D (chemical fertilizer + organic fertilizer + ducks), CD-N (chemical fertilizer 30% off + organic fertilizer + no-ducks), and CD-D (chemical fertilizer 30% off + organic fertilizer + ducks). The results showed that the application of organic fertilizer whether CM or CD significantly increased N and P concentrations over control (CK) and chemical fertilizer (CF). Moreover, no-significant differences were found in 15N fresh grain and husk concentration. Both organs ranged of 14.2-14.4 g kg-1 and 6.2-6.3 g kg-1, respectively. N derived from the fertilizer and soil significantly affected fresh grain compared to fresh husk. However, N uptake and N use efficiency did not show any differences. We concluded that organic fertilizer has a significant influence on rice growth and promote crop productivity.

According to the fact that the low convergence level on the complete elliptic integral of the first kind for the modulus which having values approach to one. In this paper we propose novelty of the complete elliptic integral consists of the new infinite series. We apply the scheme of iteration by substituting the common modulus with own modulus function into the new infinite series. We obtained so many new exact formulas of the complete elliptic integral derived from this method correspond to the number of iteration order. On the other hand, it has been also obtained a lot of new modulus functions rather than common used previously. The calculation results show that the number of significant figures of the new infinite series of the complete elliptic integral of the first kind is increased more and more. It means more fastly convergent would be obtained comparison values with the previous infinite series.

Background: This study assessed the nature of healthcare services offered in the David Umahi Federal University of Health Sciences health clinic and students' disposition to access the facility. Objectives: To assess the knowledge, attitude and practice of students in accessing healthcare services in the David Umahi Federal University of Health Sciences health clinic.Methods: Used cross-sectional design, a structured questionnaire of a five-point Likert scale as a veritable instrument for collecting the data from 50 student respondents. The questionnaire is made up of four key sections comprising student’s demographic parameters, knowledge, attitude and practice of both students and the clinic staff. Data collected was analyzed in a table of descriptive statistics to determine the total, range, mean and median, which were used to ascertain students’ utilization/accessibility disposition, perception of barriers to accessing healthcare service and overall viability of the clinic.Results: The mean value outcome of knowledge of students falls between 3.1 and 3.9, the mean value for attitude of students falls between 2.5 to 3.4 and 4.0, while the practice of students falls between mean values 2.6 and 3.1. Most of these outcomes represent poor or weak weight factor which requires several levels of intervention.Conclusion: This study highlights the overriding importance of the university healthcare clinic in maintaining a healthy study season among students of David Umahi Federal University of Health Sciences and their health-seeking behaviour. This helps to promote health, attract higher intakes and retain them in the institution till graduation.

Recently, the Portuguese parliament approved the decriminalisation of euthanasia for incurable illnesses. As the experiences of other countries show us, it will be a matter of time before mental disorders are addressed. Studying the phenomenon, particularly in vulnerable groups, in advance is essential for proper law drafting. Therefore, instruments which allow an objective assessment and comparison between groups must be available. This study aims to explore the validation of Faria's Attitude about Euthanasia scale in Portuguese older adult patients with mixed anxiety-depressive disorder. A sample of 114 older adult patients with mixed anxiety-depressive disorder collected by convenience in the Psychiatry Department of Senhora da Oliveira Hospital in Portugal was included. The pre-final version of the scale was tested in a small group with good results. The validity of the internal structure was analysed using exploratory factorial analysis. The internal consistency study verified reliability. For construct validity, we assessed the correlation with other validated scales measuring attitudes toward euthanasia, cognitive performance, personality and empathy. Attitude about euthanasia scale showed good internal consistency. One factor was retained in the principal component analysis. Significant correlations verified construct validity. The results support the scale's usefulness and validity. This study makes available a unique instrument to assess the overall tendency of the attitudes towards euthanasia in European-Portuguese, which can be used, for example, to compare Portuguese with Brazilian older adult psychiatric patients suffering from the same disorder. Furthermore, the adapted scale paves the way for other cross-cultural translations, adaptations, validations, and comparative analyses.

Women's empowerment represents a process in which they are recognized as subjects of rights. Despite advances in women's rights, inequalities persist in various areas. This study aims to validate a psychometric scale of 31 items in seven factors: Participatory Empowerment, Temerity, External Influences, Independence, Social Satisfaction and Equality. The objective is to measure the empowerment of women in the university context. The research was carried out in a transversal and non-experimental manner, with the participants' voluntary collaboration, including the participation of 1,478 university students from four Higher Education Institutions in Zone 4 of Ecuador. The data was analyzed through inferential statistics, including exploratory and confirmatory factor analysis. The results indicated that the instrument for measuring empowerment can be made up of 24 items grouped into six factors, and this model showed a good fit.

The coastal zone, situated at the sensitive interface between land and sea, serves as a pivotal area of extensive human economic activities. As one of China's economic special zones, Xiamen exemplifies the comprehensive trajectory of coastal governance in China. This research adopts an interdisciplinary approach grounded in historical geography and political ecology, employing data collection methods encompassing historical literature, field surveys, and interviews. The research findings indicate that:(1) The year 1994 witnessed the pivotal role played by the United Nations Convention on the Law of the Sea (UNCLOS) in connecting Jimei Peninsula from a local context to the international arena, thus signifying a momentous turning point in the process of scale reconstruction. However, the subsequent implementation of the Coastal Exclusion Policy in 2002 had detrimental consequences, leading to the disintegration of the local scale, the erosion of maritime culture, and the disregard for the livelihood security of displaced coastal populations.(2)The Coastal Exclusion Policy serves as an instrumental tool for implementing scale politics, while its functional realignment has had profound implications for the coastal zone, encompassing economic transformation, ecological degradation, and the marginalization of the socio-cultural fabric that intertwines humans and the coastal environment.

The Principle of Indifference (“PI”: the simplest non-informative prior in Bayesian probability) has been shown to lead to paradoxes since Bertrand (1889). Von Mises (1928) introduced the “Wine/Water Paradox” as a resonant example of a “Bertrand paradox”, and which has been presented as demonstrating that the PI must be rejected. We now resolve these paradoxes by a Maximum Entropy (MaxEnt) treatment of the PI that also includes information provided by Benford’s “Law of Anomalous Numbers” (1938). We show that the PI should be understood to represent a family of informationally-identical MaxEnt solutions; each solution being identified with its own explicitly justified boundary condition. In particular, our solution of the Wine/Water Paradox exploits Benford’s Law to construct a non-uniform distribution representing the universal constraint of scale invariance, which is a physical consequence of the Second Law of Thermodynamics.

Land cover data are important basic data for earth system science and other fields. Multi-source remote sensing images have become the main data source for land cover classification. There are still many uncertainties in the scale effect of image spatial resolution on land cover classification. Since it is difficult to obtain multiple spatial resolution remote sensing images of the same area at the same time, the main current method to study the scale effect of land cover classification is to use the same image resampled to different resolutions, however errors in the resampling process lead to uncertainty in the accuracy of land cover classification. To study the land cover classification scale effect of different spatial resolutions of multi-source remote sensing data, we selected 1 m and 4 m of GF-2, 6 m of SPOT-6, 10 m of Sentinel-2 and 30 m of Landsat-8 multi-sensor data, and explored the scale effect of image spatial resolution on land cover classification from two aspects of mixed image element decomposition and spatial heterogeneity. For the study area, we compared the classification obtained from GF-2, SPOT-6, Sentinel-2, and Landsat-8 images at different spatial resolutions based on GBDT and RF. The results show that (1) GF-2 and SPOT-6 had the best classification results, and the optimal scale based on this classification accuracy was 4–6 m; (2) the optimal scale based on linear decomposition depended on the study area; (3) the optimal scale of land cover was related to spatial heterogeneity, i.e., the more fragmented and complex was the space, the smaller the scale needed; and (4) the resampled images were not sensitive to scale and increase the uncertainty of the classification. These findings have implications for land cover classification and optimal scale selection, scale effects and landscape ecology uncertainty studies.

BACKGROUND. The aims of this study was to compare differences in daytime sleepiness between genders and qualification levels in a cohort university Chinese soccer player under 0 Covid policy restrictions in the urban area of Shanghai. METHODS. 491 questionnaires of Epworth Sleepiness Scales (ESS) were compiled online by males and females Soccer Students (SS), Semi-professional players (SP) and professional players (PP) during the ongoing measures of Shanghai lockdown. ANOVA was performed for players levels and gender. RESULTS. Significant differences were found between the 3 levels and between males and females. PP showed a very low score in the ESS (5,97) well below the threshold of 8, while SS and SP showed an ESS score above the threshold. Female showed higher scores than males. CONCLUSIONS. This study present the first data on sleepiness in Chinese soccer players of different level of qualification in a lockdown condition. Professional players has been less affected by lockdown measures than SS and SP. We can hypothesize the reasons resides in the more ordered lifestyle of PP in comparison to SS and SP, which mitigated the effects of the lockdown. Measures to improve sleep in females’ soccer player should be adopted.

Mass transfer is often the rate determining step for solid-liquid chemical reactions. Decrease of the concentration boundary layer thickness is essential to intensify the chemical reaction. Because the concentration boundary layer exists in the velocity boundary layer, force imposition in the concentration boundary layer by superimposing an electrical current and a magnetic field was proposed. Through, flow can be directly excited in the concentration boundary layer. The previous result indicates that by superimposing a DC current and a gradient magnetic field, the development of the concentration boundary layer was suppressed, because of a macro-scale flow excitation in the whole vessel. And by superimposing the gradient magnetic field with a modulate current, the development of the concentration boundary layer was further suppressed. This is because of the macro-scale flow enhancement and the excitation of a micro-scale flow near the solid-liquid interface. However, the mechanism for the micro-scale flow excitation has not been clarified. To clarify this, a uniform magnetic field was superimposed with the DC current or the modulate current. By this means, only the micro-scale flow was excited near the anode surface. The results found that the non-unform electromagnetic force distribution is the main reason for the micro-scale flow excitation.

The level of technological development of any civilization can be gaged in large part by the amount of energy they produce for their use, but also encompasses that civilization’s stewardship of their home world. Following the Kardashev definition, a Type I civilization is able to store and use all the energy available on its planet. In this study, we develop a model based on Carl Sagan’s K formula and use this model to analyze the consumption and energy supply of the three most important energy sources: fossil fuels (e.g., coal, oil, natural gas, crude, NGL and feedstocks), nuclear energy and renewable energy. We also consider environmental limitations suggested by United Nations Framework Convention on Climate Change, the International Energy Agency, and those specific to our calculations to predict when humanity will reach the level of a Kardashev scale Type I civilization.

Carton detection is an important technique in the automatic logistics system and can be applied to many applications such as the stacking and unstacking of cartons, the unloading of cartons in the containers. However, there is no public large-scale carton dataset for the research community to train and evaluate the carton detection models up to now, which hinders the development of carton detection. In this paper, we present a large-scale carton dataset named Stacked Carton Dataset (SCD) with the goal of advancing the state-of-the-art in carton detection. Images are collected from the Internet and several warehouses, and objects are labeled using per-instance segmentation for precise localization. There are total of 250,000 instance masks from 16,136 images. Naturelly, a suite of benchmarks are established with several popular detectors. In addition, we design a carton detector based on RetinaNet by embedding our proposed Offset Prediction between Classification and Localization module (OPCL) and Boundary Guided Supervision module (BGS). OPCL alleviates the imbalance problem between classification and localization quality which boosts AP by 3.1%∼4.7% on SCD at the model level while BGS guides the detector to pay more attention to boundary information of cartons and decouple repeated carton textures at the task level. To demonstrate the generalization of OPCL to other datasets, we conduct extensive experiments on MS COCO and PASCAL VOC. The improvements of AP on MS COCO and PASCAL VOC are 1.8%∼2.2% and 3.4%∼4.3% respectively. Source dataset is available here.

Scale inhibitors are deployed as preventive and rejuvenation operation in oil and gas industry when production operations are under threat or menace of scale blockage. The application of scale inhibitors is carried out through a method known as squeezing. In general, the squeeze process is governed by inhibitor-rock interaction which is described by adsorption/desorption isotherm. Most reservoirs produce loose sand grains or fine sand which float and flow within the pore spaces along with the squeezed scale inhibitors. Hypothetical reports have shown that not all scale inhibitors pumped into the formation adsorb onto the formation rock. A number of factors (irreversible adsorption, pH changes, competing ions, concentration and temperature) have been considered to affect the adsorption and return profile of these scale inhibitors. This review work examines the performances of most common scale inhibitors used in the oil and gas production activities, theoretical application in reservoirs and how loose fine sand grains affect the adsorption and desorption characteristics of squeezed scale inhibitors. Additionally, presented were overviews of previous reports on fine sand production and migration of fine sands through formation pores in reservoirs.

The Mouse Grimace Scale (MGS) was developed 10 years ago to assess pain through characterisation of changes in five facial features or action units. The strength of the technique is that it is proposed to be a measure of spontaneous or non-evoked pain. A comprehensive scoping review of the academic literature was performed. The MGS has been employed mainly in evaluation of acute pain, particularly in the pain and neuroscience research fields. There has however been use of the technique in a wide range of fields, and based on limited study it does appear to have utility for pain assessment across a spectrum of animal models. Use of the method does allow detection of pain of a longer duration, up to a month post-initial insult. There has been less use of the technique using real-time methods and this is an area in need of further research.

Small-scale fishers are considered as one of the most vulnerable communities in Bangladesh but very few studies focused on the livelihood sustainability and vulnerabilities of this professional group. A fieldwork in lower Padma and upper Meghna hilsa sanctuaries identifies different livelihood characters and associated vulnerabilities of the fishers. A conceptual framework known as Sustainable Livelihood Approaches (SLA) has been introduced to analyses the qualitative and quantitative data. The insights of the livelihood strategies provide on small-scale fishers and fisheries management have been explained and explored. Fishers are found solely dependent on fishing, economically insolvent and neglected. In addition, some socio-economic abstractions such as low income, credit insolvency, lack of substitute earning flexibility make them more vulnerable. A number of effective suggestions are elicited from fishers’ perceptions, the implementation of which is crucial to ensure livelihood sustainability of the small-scale fishers.

Friction is an important subject for sustainability due to problems associated with energy loss. Recent years, surface micro- and nanostructures have attracted much attention to reduce friction; however, suitable structures are still under consideration. Many functional surfaces are present in nature, such as the friction reduction surfaces of snake skins. In this study, we focused on firebrats, Thermobia domestica, living in narrow spaces such as under bark, so their surface frequently contacts with surrounding surfaces. We speculate that their body surface would be adapted to reduce friction. To investigate the firebrat surface functions, firebrat surfaces were observed by using a field-emission scanning electron microscope (FE-SEM) and a colloidal probe atomic force microscope (AFM), respectively. Results of surface observations by the FE-SEM revealed that firebrats are entirely covered with scales, whose surfaces have micro groove structures. Scale groove periods around the firebrat's head are almost uniform within a scale but vary between scales. AFM friction force measurements revealed that firebrat scale reduces friction by decreasing contact area between scales and a colloidal probe. The heterogeneity of groove periods of the scales suggest that it is difficult to fix the whole body in particular rough surfaces and that lead to be "fail-safe".

Size-based fungal growth studies have limitations. For example, the growth in size stops in closed systems once it reaches the borders and poorly describes the metabolic status, especially in the stationary phase. This might lead mycotoxin studies to unrealistic results. Color change could be a viable alternative as pigments are results of the mold’s metabolic activity. This study aimed to verify the possibility of using gray values and the RGB system to analyze the growth of Fusarium graminearum. It consisted color and area measurement using the ImageJ software for specimens grown in yeast extract agar (YEA). The results suggest the usability of color and gray values as reliable tools to analyze the growth of F. graminearum.

This the term "Bubungan Tinggi" (High Roof) in this study refers to the banjarese traditional house. A significant artifact in South Kalimantan is called Bubungan Tinggi. With its unique typology and anatomy, this particular building has evolved into an iconic structure that symbolizes the collective memory of the Banjarese people. This research aims to showcase the versatility of the Bubungan Tinggi design in modern architecture by exploring different transformation models. By applying various techniques and approaches, the study provides insights into how this traditional Banjarese character can be adapted for new house designs. The Bubungan Tinggi's transformation process reveals characteristics in its fundamental components, which are distinguished by their geometric objects. Experimental design is the methodology employed in this study. This methodology shows that a variety of transformation models may be carried out by introducing and identifying the Bubungan Tinggi, observing objects in case studies, using transformation techniques and their application, and creating transformation models. This research produced a variety of modeling results that illustrated new interpretations of bubungan tinggi's in modern house design. The incorporation of traditional elements like the bubungan tinggi in modern house design can help preserve cultural heritage while also creating unique and innovative architectural solutions.

EIMIs face the challenge of adapting to the Paris Agreement and the European Green Deal to achieve carbon neutrality. This change is being driven by consumer interest in low-carbon products, regulatory requirements from climate agreements and investors prioritizing sustainability. This pressure is pushing companies to go beyond short-term financial gains and integrate sustainability into their business. The growing awareness of the environmental impact of business models (BM) has fueled the development of Sustainable Business Models (SBMs). This study aims to link the discussion on the role of SBMs in the drivers of decarbonization, to improve the understanding of how the drivers can be integrated and enable new BMs for EIMIs. Based on a structured literature review, semi-structured interviews were conducted in the EIMIs. The study identifies BM-components that are influenced by these drivers and require sustainable business model innovation (SBMI). The results show that decarbonization drivers have a significant impact on all BM components. Experts emphasize the importance of collaborative approaches and cooperation throughout the value chain. This research elaborates on the importance of systematic analysis to understand how companies can effectively manage decarbonization drivers and suggests in-depth exploration within BM-research to uncover potential SBM design options.

Adaptation to the impacts of human induced global heating is inevitable. For a socially just and ecological sustainable adjustment to these new circumstances, we need to draw from diverse knowledge systems while, simultaneously, foster a social-ecological transformation. We approach these concerns through the concept of community-based adaptation (CBA) and discuss remedies. Synergies with feminist knowledge systems and indigenous ways of living show the transdisciplinary essence of CBA. By abstracting from its origin and overlapping disciplines, revealing the social metabolism as a common problem, CBA is prone to achieve more equitable and sustainable adjustments. Transdisciplinarity itself and the current related CBA literature point beyond mere adjustments and call for a redesign of the social metabolism, thereby shifting from adaptation to global heating towards adaptation with nature by focusing on social provisioning. An engagement with transformative adaptation and heterodox economics further shows the potential of CBA to serve as an instrument in support of a social-ecological transformation by addressing root causes of vulnerability and by fostering epistemic justice. Reflecting these points back on the epistemological and ontological assumptions of CBA, the viewpoint proposes critical realism as a guiding philosophy of science to move forward.

In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’)  A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite  austenite transformation in the same temperature range.

Time and space are fundamental concepts for characterizing and understanding our world. Despite of continuous curiosity and extensive studies, the nature of time and space remains elusive, and the underlying quantum structure is unclear. Here we propose a molecular model based on energy space decomposition to incorporate time and space synthetically in a unified framework. In the proposed model, the multipole expansion of action mapped to energy modules in scalar, vector, and matrix forms, results in the generators of time, space, and a material framework, cloud. And the invariance of time, space and cloud transformation corresponds to the conservation of energy, momentum, and mass, respectively. The classification of energy modules reveals a periodicity of energy elements, which constructs a hierarchical world in a molecular framework with dynamics represented by energy transformations. Here the role of time and space could switch from each other, and motion is attributed to the coupling of particle with intermediate bosons, corresponding to energy transformations among different energy modules. The application on Bohr model demonstrates that this picture provides a consistent classical interpretation to the foundation of quantum mechanics, and suggests an atomic model for gravitation.

This paper investigates the ion-acoustic wave structures in fluid ions for the Benjamin-Bona-Mahony-Peregrine-Burgers (BBMPB) equation. The various types of wave structures, are extracted including the three-wave hypothesis, breather wave, lump periodic, mixed-type wave, periodic cross-kink, cross-kink rational wave, M-shaped rational wave, M-shaped rational wave solution with one kink wave and M-shaped rational wave with two kink wave solutions. The Hirota bilinear transformation is a powerful tool that allows us to accurately solutions and predict the behavior of these wave structures. Through our analysis, we gain a better understanding of the complex dynamics of ion-acoustic waves and their potential applications in various fields. Moreover, our findings contribute to the ongoing research in plasma physics that utilize ion-acoustic wave phenomena. To show the physical behavior of the solutions, some 3D plots have been performed and their respective contour level, choosing different values of the parameters.

Lasiodiplodia theobromae, as one of the causing agents associated with Chinese hickory trunk cankers, has caused huge economic losses to the Chinese hickory industry due to its extremely strong pathogenicity. Though the biological characteristics of this pathogen and the occurrence pattern of this disease have been reported, few studies have focused on investigating the mechanisms responsible for L. theobromae survival strategies and pathogenicity. The high-quality genome data and the efficient transformation system are the basis for researching above mechanism events. In this study we sequenced and assembled L. theobromae strain LTTK16-3, and established the first protoplasmic preparation method and polyethylene glycol (PEG) -mediated genetic transformation system for L. theobromae. These genetic information and transformation methods established the foundation for the future mechanisms study of L. theobromae and set up the possibility of targeted molecular improvements for Chinese hickory canker control.

Improvement of agronomic traits in crops through gene editing (GE) relies on efficient trans-formation protocols for delivering the CRISPR/Cas9-coded transgenes. Recently, a few embryo-genesis-related genes have been described, the co-delivery of which significantly increases the transformation efficiency with reduced genotype dependency. Here we characterized the trans-genic and GE events in wheat (cv. Fielder) when transformed with the GROWTH-REGULATING FACTOR 4 (GRF4) and its cofactor GRF-INTERACTING FACTOR 1 (GIF1) chimeric gene. Trans-formation efficiency in our experiments ranged from 22% to 68%, and the editing events were faithfully propagated into the following generation. Both low and high copy number integration events were recovered in the T0 population with the various level of integrity of the left and right T-DNA borders. We also generated a population of wheat plants with ten different gRNAs targeting 30 loci in the genome. Comparison of the epigenetic profiles at the target sites and editing efficiency revealed a significant positive correlation between chromatin accessibility and muta-genesis rate. Overall, preliminary screening of the transgene quality and GE events in the T0 population of plants regenerated through the co-delivery of GRF-GIF can allow for the propagation of the best candidates for further phenotypic analysis.