Elliptic curve cryptography (ECC) over prime fields relies on scalar point multiplication realized by point addition and point doubling. Point addition and point doubling operations consist of many modular multiplications of large operands (256 bits for example), especially in projective and Jacobian coordinates which eliminate the modular inversion required in affine coordinates for every point addition or point doubling operation. Accelerating modular multiplication is therefore important for high-performance ECC. This paper presents the hardware implementations of modular multiplication algorithms, including 1) Interleaved modular multiplication (IMM), 2) Montgomery modular multiplication (MMM), 3) Shift-sub modular multiplication (SSMM), 4) SSMM with advance preparation (SSMMPRE), and 5) SSMM with CSAs and sign detection (SSMMCSA) algorithms, and evaluates their execution time (the number of clock cycles and clock frequency) and required hardware resources (ALMs and registers). Experimental results show that SSMM is 1.76 times faster than IMM, and SSMMCSA is 3.21 times faster than IMM. We also present the ECC hardware implementations based on the Secp256k1 protocol in affine, projective, and Jacobian coordinates using the IMM, SSMM, SSMMPRE, and SSMMCSA algorithms, and investigate their cost and performance. Our ECC implementations can be applied to the design of hardware security module systems.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

Background: The use of peripherally inserted central catheters and midline catheters is growing due to their potential benefits. These devices can increase patient safety and satisfaction while reducing the use of resources. As a result, many hospitals are establishing vascular access specialist teams staffed by nurses who are trained in the insertion and maintenance of these catheters. Objective: Evaluate ex-ante whether the benefits of replacing peripheral venous catheters, peripherally inserted central catheters and midline catheters with ultrasound-guided peripherally inserted central catheters and midline catheters by a vascular access specialist team outweigh their costs. Methods: Cost-benefit analysis from the perspective of the healthcare provider based on administrative data. The study estimates the reduction in resources used when replacing peripherally inserted central catheters, midline catheters and peripheral venous catheters with ultrasound-guided peripherally inserted central catheters and midlines, as well as the additional resources required for their use. Results: Each ultrasound-guided peripherally inserted central catheter replacing a peripherally inserted central catheter, results in a measurable resource reduction of approximately €31. When 3 peripheral venous catheters are replaced by an ultrasound-guided peripherally inserted central catheter, the saving is €63. Similarly, each ultrasound-guided midline catheter replacing a midline, results in a reduction of €16, while each ultrasound-guided midline catheter replacing 3 peripheral venous catheters results in a reduction of €96. Conclusion: The benefits of replacing peripheral venous catheters, peripherally inserted central catheters and midline catheters by introducing a vascular access specialist team trained in the implantation of ultrasound-guided peripherally inserted central catheters and midline catheters, outweigh its cost mainly because of the decrease in hospital stay due to the lowered risk of healthcare-associated infections. These results motivate the implementation of the service, adding to previous experience suggesting that it is also preferable from the point of view of patient safety and satisfaction.

The sonification of data to communicate information to a user is a relatively new approach that established itself around the 1990s. To date many researchers design their individual sonification from scratch. There are no standards in sonification design and evaluation. But researchers and practitioners have formulated several requirements and established several methods. There is wide consensus that psychoaocustics could play an important role in the sonification design and evaluation phase. But this requires an adaption of psychoacoustic methods to the signal types and the requirements of sonification. In this method paper we present PAMPAS, a PsychoAcoustical Method for the Perceptual Analysis of multidimensional Sonification. A well-defined and well-established, efficient, reliable and replicable Just Noticeable Difference experiment using the Maximum Likelihood Procedure serves as the basis to achieve linearity of parameter mapping during the sonification design stage and to identify and quantify perceptual effects during the sonification evaluation stage, namely the perceptual resolution, hysteresis effects and perceptual interferences. The experiment results are universal scores from a standardized data space and a standardized procedure. These scores can serve to compare multiple sonification designs of a single researcher, or even between different research groups. The method can supplement other sonification design and evaluation methods from a perceptual viewpoint.

The health of the landing gear retraction and extension hydraulic system may be assessed using fuzzy comprehensive evaluation (FCE), however the traditional FCE method depends solely on human assessment by specialists, which is excessively subjective. To address the issue of excessive human subjective variables in the assessment, an improved FCE model based on enhanced risk coefficient is provided, which includes four consideration indexes: failure probability, failure severity, failure detection difficulty, and failure repair difficulty. To reduce subjective human judgment errors entirely due to expert experience, the improved FCE takes into account the likelihood of failure using a statistical method, the severity of failure using a fault simulation analysis based on the LMS Imagine.Lab AMESim simulation platform, and the difficulty of fault detection and repair using the aircraft manufacturer's professional maintenance information. As part of the evaluation model, the range of health assessment values and accompanying treatment methods are included, making it easier to implement on a daily basis in aircraft maintenance. As a final step, the simulation is evaluated and the simulated faults are calculated.

Measuring bias is important as it helps identify flaws in quantitative forecasting methods or judgmental forecasts. It can, therefore, potentially help improve forecasts. Despite this, bias tends to be under-represented in the literature: many studies focus solely on measuring accuracy. Methods for assessing bias in single series are relatively well-known and well-researched, but for datasets containing thousands of observations for multiple series, the methodology for measuring and reporting bias is less obvious. We compare alternative approaches against a number of criteria when rolling-origin point forecasts are available for different forecasting methods and for multiple horizons over multiple series. We focus on relatively simple, yet interpretable and easy-to-implement metrics and visualization tools that are likely to be applicable in practice. To study the statistical properties of alternative measures we use theoretical concepts and simulation experiments based on artificial data with predetermined features. We describe the difference between mean and median bias, describe the connection between metrics for accuracy and bias, provide suitable bias measures depending on the loss function used to optimise forecasts, and suggest which measures for accuracy should be used to accompany bias indicators. We propose several new measures and provide our recommendations on how to evaluate forecast bias across multiple series.

Time-domain spectroscopy (TDS) in the Terahertz (THz) frequency range is gaining in importance in nondestructive testing of dielectric materials. One application is the layer thickness measurement of a coating layer. To determine the thickness from the measurement data, the refractive index of the coating layer must be known in the surveyed frequency range. For perpendicular incidence of the radiation, methods exist to extract the refractive index from the measurement data itself without prior knowledge. This paper extends these methods for non-perpendicular incidence, where the polarization of the radiation becomes important. Furthermore, modifications considering effects of surface roughness of the coating are introduced. The new methods are verified using measurement data of a sample of Inconel steel coated with yttria-stabilized zirconia (YSZ) and with COMSOL simulations of the measurement setup. To validate the thickness measurements, scanning electron microscopy (SEM) images of the layer structure are used. The results show good agreement with an average error of 1% for the simulation data and under 4% for the experimental data compared to reference measurements.

Urethral pain syndrome (UPS) is still a pathology in which the diagnosis is formulated as a "diagnosis of exclusion". The exact pathogenetic mechanisms are not yet fully understood and clear recommendations for the prevention and treatment of UPS are absent. The goal of the study was to assess the condition of the tissues in the female urethra in UPS, by using transvaginal ultrasound (TVUS) and cross-polarization optical tomography (CP OCT). TVUS showed an expansion in the diameter of the internal lumen of the urethra, especially in the proximal region compared with the norm. Compression elastography revealed areas with increased stiffness (presence of fibrosis) in urethral and surrounding tissues. When studied with CP OCT it was shown that with UPS, the structure of the tissues in most cases was changed: trophic alterations in the epithelium (hypertrophy or atrophy) and fibrosis of underlying connective tissue were observed. The proximal fragment of the urethra with UPS underwent changes identical to those of the bladder neck. This paper showed that the introduction of new technology — CP OCT — in conjunction with TVUS will allow verification of structural changes in tissues of the lower urinary tract at the level of their architectonics and will help doctors understand better the basics of the UPS pathogenesis.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

The significance of digital sustainability in donation-based crowdfunding platforms lies in its ability to encourage environmentally aware and socially responsible practices in the sphere of online philanthropy. Fundraising has been revolutionized by the emergence of donation-based crowdfunding platforms. This study explores the various factors influencing individuals' attitudes towards these platforms, particularly focusing on perceived usefulness, ease of use, credibility, and self-efficacy. The study examines how these factors affect donation intentions and electronic word-of-mouth intentions, utilizing data from 326 college students. The findings confirm that perceived usefulness, ease of use, credibility, and self-efficacy play crucial roles in shaping attitudes. Furthermore, these attitudes significantly impact both donation intentions and electronic word-of-mouth intentions. Adjustments to the structural model highlight the interconnectedness of these factors, improving the model's accuracy. The results provide practical guidance for platform administrators, campaign creators, and stakeholders involved in online philanthropy, emphasizing the need for user-friendly designs, trust-building, and fostering user confidence for successful crowdfunding efforts.

Such rapidly changing external conditions as the COVID-19 pandemic and the war in Ukraine, being pure crisis phenomena, not only determine the geopolitical and geoeconomic situation on the global markets, but also cause structural changes in individual countries. Under these conditions, the level of food self-sufficiency becomes particularly important, as it is one of the factors determining the food security of any country. The aim of the research is to assess Ukraine's food self-sufficiency compared to the European Union and Poland. The self-sufficiency ratio (SSR) index was used to assess food self-sufficiency. This is the ratio of the volume of production of the most important products of plant and animal origin to the volume of domestic consumption. Domestic consumption was defined as the volume of domestic production increased by the volume of imports, reduced by the volume of exports and also included changes in domestic stock levels. The surveyed time frame is 2019–2021. The analyzed data were taken from the State Statistics Service of Ukraine, FAOSTAT, USDA and Statistics Poland. A comparative analysis of self-sufficiency for the main agri-food sectors of Ukraine, the EU, and Poland showed significant differences. Taking into account the production potential and food self-sufficiency indicators of Ukraine, Ukraine's possible accession to the EU can be expected to have a major impact on the EU's supply and demand situation, as it may pose a threat to many EU agri-food sectors.

Quinacridone (QA) and 2,9-dimethylquinacridone (DQA) are synthetic substances suitable as a hard, abrasion-resistant, self-organizing gliding layer on ice, snow, and water. For sustainable use, a large number of parameters must be considered to demonstrate that these non-biogenic substances and their by-products and degradation products are harmless to humans and the environment in the quantities released. For this task, available experimental data are used and supplemented for all tautomers by numerous relevant physical, chemical, toxicological and ecotoxicological estimated values based on various Quantitative Structure Activity Relationship (QSAR) methods. On the one hand, the low solubility of QA and DQA leads to stable gliding layers and thus low abrasion and uptake by plants, animals, and humans. On the other hand, the four hydrogen bond forming functional groups per molecule allow nanoparticle decomposition and enzymatic degradation in natural environments. All available data justify a sustainable use of QA and DQA as a gliding layer. The assessment of the toxicological properties is complemented with an investigation of the size and morphology of DQA particles as well as field tests indicating an excellent performance as a gliding layer on snow.

Stroke causes disability and significantly affects patient quality of life. Post-stroke rehabilitation of upper limb function is crucial, as it affects daily activities and individual autonomy. Traditional rehabilitation methods often require frequent visits to specialized centers, which can be costly and challenging. This study investigated the effectiveness of a home-based self-training device, "Kenko Yusuri," in improving upper limb function in patients with chronic stroke. This multicenter prospective intervention study used a quasi-randomized controlled trial design. Ninety-three outpatients from five hospitals in Japan were enrolled and assigned to either the intervention group who used the "Kenko Yusuri" device or the control group who underwent conventional rehabilitation. All patients received botulinum toxin type A (BoNT-A) injections to treat upper limb spasticity. The primary outcome measure was the Fugl-Meyer Assessment (FMA) of upper-extremity motor function. Secondary outcomes included the modified Ashworth scale (MAS) score, range of motion (ROM), and chronic pain assessments. The intervention group demonstrated significantly greater improvements in FMA total scores than the control group. Patients with moderate paralysis experienced the greatest benefits from the intervention. There were no significant between-group differences in MAS scores or ROM measurements. Pain and wrist ROM showed improvement in the intervention group. Home-based training with a shaking device significantly improved upper limb function in patients with moderate chronic post-stroke paralysis. This approach aligns with the principles of use-dependent plasticity and offers a feasible and cost-effective alternative to traditional rehabilitation methods.

This study presents the chemical synthesis, purification, and characterization of a novel non-natural synthetic amino acid. The compound was synthesized in solution, purified, and characterized using NMR spectroscopy, polarimetry, and melting point determination. Dynamic Light 22 Scattering (DLS) analysis demonstrated its ability to form aggregates with an average size of 391 nm, extending to low micrometric sizes. Furthermore, cellular biological assays revealed its ability to enhance fibroblast cell growth, highlighting its potential for tissue regenerative applications. Circular dichroism (CD) spectroscopy showed the ability of the synthetic amino acid to bind serum albumins (using bovine serum albumin (BSA) as a model), and CD deconvolution provided insights into the changes in secondary structures of BSA upon interaction with the amino acid ligand. Additionally, molecular docking using HDOCK software elucidated the most likely binding mode of the ligand inside the BSA structure. We also performed in silico oligomerization of the synthetic compound in order to obtain a model of aggregate to investigate computationally. More in detail, in the dimer formation achieved by molecular self-docking, two distinct poses were observed, corresponding to the lowest and comparable energies, with one pose exhibiting a quasi-coplanar arrangement characterized by a close alignment of two aromatic rings from the synthetic amino acids within the dimer, suggesting the presence of π-π stacking interactions. In contrast, the second pose displayed a non-coplanar configuration, with the aromatic rings oriented in a staggered arrangement, indicating distinct modes of interaction. Both poses were further utilized in the self-docking procedure. Notably, iterative molecular docking of amino acid structures resulted in the formation of higher-order aggregates, with a model of a 512-mer aggregate obtained through self-docking procedures. This model of aggregate presented a cavity capable of hosting therapeutic cargoes and biomolecules, rendering it a potential scaffold for cell adhesion and growth in tissue regenerative applications. Overall, our findings highlight the potential of this synthetic amino acid for tissue regenerative therapeutics and provide valuable insights into its molecular interactions and aggregation behavior.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

Lipophilic oligonucleotide derivatives are a potent approach to the intracellular delivery of nucleic acids. The binding of these derivatives to serum albumin is a major determinant of their fate in the body, as its structure contains several sites of high affinity for hydrophobic compounds. This study focuses on the features of self-association and non-covalent interactions with human serum albumin of novel self-penetrating oligonucleotide derivatives. The study revealed that the introduction of a triazinyl phosphoramidate modification bearing two dodecyl groups at the 3' end region of the oligonucleotide sequence has a negligible effect on its affinity for the complementary sequence. Dynamic light scattering verified that the amphiphilic oligonucleotides under study can self-assemble into micelle-like particles ranging from 8 to 15 nm in size. The oligonucleotides with dodecyl groups form stable complexes with human serum albumin with a dissociation constant of approximately 10-6 M. The oligonucleotide micelles are simultaneously destroyed upon binding to albumin. Using an electrophoretic mobility shift assay and affinity modification, we examined the ability of DNA duplexes containing triazinyl phosphoramidate oligonucleotides to interact with Ku antigen and PARP1, as well as the mutual influence of PARP1 and albumin or Ku antigen and albumin upon interaction with DNA duplexes. These findings, together with the capability of dodecyl-containing derivatives to effectively penetrate different cells, such as HEK293 and T98G, indicate that the oligonucleotides under study can be considered as a platform for the development of therapeutic preparations with a target effect.

Background: Coronavirus disease (COVID-19) has caused one of the worst global pandemics in recent decades. It has disrupted education systems worldwide, leading to a forced shift from traditional face-to-face to blended or fully distanced learning, requiring a higher level of student readiness for self-directed learning (SDL) and a more internal locus of control (LOC). Objective: This study explored the relationship between locus of control and level of readiness for SDL among Saudi nursing students and whether the COVID-19 pandemic has impacted this relation-ship. Methods: a cross-sectional correlational descriptive study was conducted to survey 277 Saudi nursing students enrolled in the bachelor program at one of the reputable universities in Saudi Arabia. An E-questionnaire containing two scales, the Self-Directed Learning Readiness Scale for Nursing Education, and the Locus of Control Scale, was used to collect data in addition to the selected participants’ characteristics. Results: Nursing students had a moderate-to-low level of readiness for SDL (mean = 144.0), and the majority had an external LOC. There was a significant association between the locus of control and level of readiness for self-directed learning (r = 0.19*, p = 0.001), and the internal locus of control was more significantly associated with self-directed learning (r = 0.22*, p = 0.0001) than with external locus of control. Conclusion: The study findings indicate a propensity of respondents towards an external locus of control, whereas most of the respondents’ reported levels of readiness ranged between low and moderate across all dimensions of self-directed learning. This study was not registered.

Conclusion: When applied to the air-abraded Filtek™ Bulk Fill Flowable Restorative composite surface, 10-MDP-containing adhesives perform better than 10-MDP-free adhesives. The binding strength was unaffected by the 10-MDP-containing adhesives' chemical makeup. The bond strength endurance of adhesives containing 10-MDP decreases with age. Keywords: keyword 1; keyword 2; keywords: low-viscosity bulk fill composite, universal adhesives, self-etch adhesive, 10-MDP, aging, bond strength.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

Algal-bacterial granular sludge, a new biological technology, has been widely recognized due to its highly effective pollutant treatment and energy efficiency. This study investigated the effects of environmental concentrations of Cr(VI) (0.5-2.5 mg/L) on the performance of algal-bacterial gran-ular sludge and self-defensive responses after 90 days of cultivation. The results showed that Cr(VI) affected chemical oxygen demand (COD), ammonia-N and phosphate removal with different trends being apparent. A linear decline in COD removal was observed, whereas an initial de-creasing and then increasing ammonia-N and phosphate removal took place. Algal-bacterial granular sludge effectively removed Cr(VI) from wastewater through biological adsorption and reduction, showing the potential to treat Cr(VI)-contaminated wastewater. Cr(VI) affected the community abundance of the algal-bacterial granular sludge, in which Chlorophyceae and cya-nobacteria were vulnerable under Cr(VI)-induced stress. To reduce the toxicity of Cr(VI), over-produced EPS-PN and antioxidant enzymes (MDA, SOD and CAT) acted as self-defensive responses to resist oxidative damage. This study showed that algal-bacterial granular sludge can remove 00.5 mg/L of Cr(VI) without performance loss. It is hoped that this study can provide useful information for improved engineering feasibility of algal-bacterial granular sludge.

DFT-D3 calculations based on structural X-ray diffraction data obtained for 3-oxo-camphorsulfonyl imine (1), camphorsulfonyl chloride (2) and seven camphor sulfonimines (O2SNC10H13NR, L1-L7) from which L2 (R=4-OHC6H4), L4 (R=4-ClC6H4) and L6 (R=3,5-(CH3)2C6H3) are new, provide information into the intra and inter molecular interactions with concomitant elucidation of the supramolecular arrangement of the compounds. The DFT D3 calculations performed in small clusters of 2 or 3 molecular units reproduce the interactions observed by X-ray analyses showing that as a general trend the structural arrangement of the molecules is driven by electronic rather than by packing parameters. In all compounds the self-assembly of 3D structures involves the sulfonyl imine group ( NSO2) either to establish hydrogen bonds, through the oxygen atoms or non-classic oxygen-aliphatic hydrogen or non-bonding interactions (NBI) which also involve the sulfonyl oxygens. Interestingly, the camphor sulfonimine compounds (L2, L3) having protic groups (R=C6H4X: X=OH, L2 or X=NH2, L3) at the aromatic imine substituents (=NR) present an extra π-π stacking which is absent in the other compounds aromatic derivatives. The X-ray analysis shows that all the reported camphor sulfonimine compounds display the E configuration with respect to the imine substituent (R). The study of the redox behavior of the compounds by cyclic voltammetry allows an insight into the solution properties of the compounds and the rationalization of the molecular interactions that stand in the solid and solution states. Camphor sulfonimine compounds (L) display appropriate binding atoms to coordinate transition metals. The herein results show that monodentate coordination through the nitrogen atom of the sulfonimine 5-membered ring to the {Ag(NO3)} metal center is favored. When this imine nitrogen atom is not itself involved in the Organic Framework DFT-D3 calculations shows that the complexation does not affect the non-covalent interactions that are reproduced in the MOF structure.

In swarm-robotics foraging, the purpose of task allocation is to adjust the number of active foraging robots dynamically based on the task demands and changing environment. It is a difficult challenge to generate self-organized foraging behavior in which each robot can adapt to environmental changes. To complete the foraging task efficiently, this paper presents a novel self-organized task allocation strategy known as the dynamic response threshold model (DRTM). To adjust the behavior of the active foraging robots, the proposed DRTM newly introduces the traffic flow density, which can be used to evaluate the robot density. First, the traffic flow density and the amount of obstacle avoidance are used to adjust the threshold which determines the tendency of a robot to respond to a stimulus in the environment. Then, each individual robot uses the threshold and external stimulus to calculate the foraging probability that determines whether or not to go foraging. Simulation and physical experiments are carried out to evaluate the performance of the proposed method. The experimental results show that the DRTM is superior to and more efficient than the adaptive response threshold model (ARTM) in swarm foraging.

Material selection for product design is a complex task. Thus, one of the objectives of this work is to analyze, understand and promote the importance of selection of materials to conceive quality products with help of designers' that promote green self-identity in the early stage of the conception of new products. A questionnaire was sent to professional designers and engineers. 38 responses were validated, this being the sample of our study. The aspects that influence the complex selection of materials and the final quality of the products through the design and production process is presented. As a result of the answers carried out with product designers who work in the market, with students who are graduating and with some engineers, a new approach for the selection of materials was developed. Based on a collection of main ideas from traditional and non-traditional methods of material selection, seeking to group the maximum requirements of both methods, inspired by the "Canvas" model on the basic modular methodology, a new model for a project of new product is presented. Our study focuses on the selection of materials, since this aspect is one of the most relevant steps in early stage of the prototyping phase of new products, with a view to reducing CO² from the air in the atmosphere that we all breathe. The classification of materials is complex, due to the diversity of available options. The novelty of this model is that all properties of the newly designed product, such as technical, aesthetic, productive, environmental and other properties, are all grouped in a model, which serves as an innovative support. Thus, the designer has at his disposal a tool that can help him in the selection of the best material for the products he designs. This study intends to make a contribution in the field of material selection, quality and design of new products, promoting a green self-identity for designers in the initial phase of product design. Consequently, all consumers in search of a sustainable planet will profit from it.

This study compares the effects of lecture-based instruction and process-oriented guided inquiry learning (POGIL)-based instruction on the self-efficacy performance of Grade 12 students. A quasi-experimental, pretest-posttest design was adopted to investigate and assess the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes; Knowing, Applying and Reasoning (KAR). Two government high schools in Alain were selected as research sites, one for the boys and one for the girls. The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys), and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a circular motion unit in physics using POGIL-based instruction, while the control group was taught the unit using lecture-based instruction. The study's findings showed statistically significant differences between students of the control group and the treatment group in favour of the latter regarding their science performance, self-efficacy and science-related attitudes. Moreover, positive correlations were found between participants’ performance at the KAR test, self-efficacy and scientific attitudes towards scientific inquiry after the intervention. In conclusion, it is recommended to shift teaching towards POGIL-based instruction due to its positive impact on students’ performance and self-efficacy. It is also suggested to replicate the study to include government and private schools, elementary and high schools, teachers and advisors.

Body Expression (BE) has been defined in the past decades as a discipline within Physical Education (PE) with very particular characteristics and a strong emotional component. In this study, a programme of this discipline was applied to university Physical Activity and Sports Sciences (PASS) students from six consecutive academic years: three prior to and three during the pandemic. A pre-post design was used to determine how the BE programme affected the university students' self-concept (SC). To do so, a questionnaire with a multidimensional approach to this construct was administered, whose dimensions were closely related to the BE programme's characteristics. The results revealed significant improvements in the final SC, compared to the initial SC. Men reported lower SC values than women before the programme implementation, but higher at the end. Therefore, the change was larger in men, so the programme may have had an equalising effect between groups. It was also verified that the pandemic had particularly affected women.

Quantitative differential phase contrast (qDPC) imaging has become an important method of optical measurement and life science research in microscopy because of its high reconstruction resolution and non-invasive, high-contrast and quantitative imaging of biological samples. Despite the continuous development of the principle and algorithm, the frame rate of the existing qDPC algorithm is still much lower than that of camera acquisition, so it is hardly applied to real-time image the fast-moving biological samples. In this paper, based on color-coded multiplexing strategy, a compact real-time quantitative phase imaging system is designed to realize multi-mode imaging. The system employs a programmable LED array to illuminate directly, and the phase reconstruction algorithm is deployed in the graphics processing unit (GPU) of the laptop to accelerate the calculation. The system can achieve high-speed quantitative phase imaging of non-stained biological samples, and the frame rate can reach 60fps. The device has the advantages of compact structure, low cost and portability. Thus, it is suitable for mobile medical applications.

In remote sensing applications, one of the key points is the acquisition, real-time pre-processing and storage of information. Due to the large amount of information present in the form of images or videos, compression of this data is necessary. Compressed sensing (CS) is an efficient technique to meet this challenge. It consists in acquiring a signal, assuming that it can have a sparse representation, using a minimal number of non-adaptive linear measurements. After this CS process, a reconstruction of the original signal must be performed at the receiver. Reconstruction techniques are often unable to preserve the texture of the image and tend to smooth out its details. To overcome this problem, we propose in this work, a CS reconstruction method that combines the total variation regularization and the non-local self-similarity constraint. The optimization of this method is performed by the augmented Lagrangian which avoids the difficult problem of non-linearity and non-differentiability of the regularization terms. The proposed algorithm, called denoising compressed sensing by regularizations terms (DCSR), will not only perform image reconstruction but also denoising. To evaluate the performance of the proposed algorithm, we compare its performance with state-of-the-art methods, such as Nesterov's algorithm, group-based sparse representation and wavelet-based methods, in terms of denoising, and preservation of edges, texture and image details, as well as from the point of view of computational complexity. Our approach allows to gain up to 25% in terms of denoising efficiency, and visual quality using two metrics: PSNR and SSIM.

We reveal the significance of plasmonic nanoparticle’s (NP) shape and its surface morphology en route to an efficient self-assembled plasmonic nanoparticle cluster. A simplified model is simulated in the form of free-space dimer and trimer nanostructures (NPs in shape of sphere, cube, and disk). A ~ 200 % to ~ 125% raise in near field strength (gap mode enhancement) is observed for spherical NPs in comparison with cubical NPs (from 2 nm to 8 nm gap sizes). Full-width three-quarter maximum reveals better broad-spectral optical performance in a range of ~ 100 nm (dimer) and ~ 170 nm (trimer) from spherical NPs as compared to a cube (~ 60 nm for dimer and trimer). These excellent properties for sphere-based nanostructures are merited from its dipole mode characteristics.

In light of the self-simulation hypothesis, a simple form implementation of the principle of efficient language is discussed in a self-referential geometric quasicrystalline state sum model in three dimensions. Emergence is discussed in context of geometric state sum models.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

The notion of hierarchy is a key characteristic of any complex system. This paper explores which notions of hierarchy are being used in the field of management and organization studies. Four distinct types of hierarchy are identified: a ladder of formal decision-making authority, a ladder of achieved status, a self-organized ladder of responsibility, and an ideology-based ladder. A social mechanism-based perspective serves to define and distinguish these four types. Subsequently, the typology is further developed by comparing the four hierarchy types in terms of their tacit/explicitness, (in)transitivity, and behavior- versus cognition-centeredness. This review article contributes to the literature by dissecting the general metaphor of hierarchy into four different constructs and their social mechanisms, which serves to create a typology of the various ways in which complex systems can be characterized as being hierarchical. This typology can inform future research drawing on any type of hierarchy.

Climate change is likely to have a complex effect on the growth of plants, their phenology, plant-pollinator interactions, and reproductive success. Therefore, we tested the impact of three key factors (temperature, water, and nitrogen supply) on traits, pollination, and seed production in Sinapis alba (Brassicaceae). We grew the plants in different combinations of temperature, water, and nitrogen supplementation, measured multiple vegetative and floral traits, and assessed the response of pollinators in the field. We also evaluated the effect of growing conditions on seed set in plants exposed to pollinators and hand-pollinated plants. Our results show that water stress impaired vegetative growth, decreased flower production, reduced visitation by pollinators and seed set, while nitrogen availability played an important role in nectar production. Temperature modulated the effect of water and nitrogen availability on vegetative and floral traits and strongly affected flowering phenology and flower production. We demonstrated that changes in temperature, water, and nitrogen availability induce changes in plant vegetative and floral traits which impact flower visitation and consequently plant reproduction. Climate change, particularly increasing temperature combined with reduced precipitation, thus may impact plant-pollinator interactions with negative consequences for the reproduction of wild plants and insect-pollinated crops.

Since the emergence of the quantified self movement, users aim at health behavior change, but only those who are sufficiently motivated and competent with the tools will succeed. Our literature review shows that theoretical models for quantified self exist but they are too abstract to guide the design of effective user support systems. Here, we propose principles linking theory and implementation to arrive at a hierarchical model for an adaptable and personalized self-quantification system for physical activity support. We show that such a modeling approach should include a multi-factors user model (activity, context, personality, motivation), a hierarchy of multiple time scales (week, day, hour), and a multi-criteria decision analysis (user activity preference, user measured activity, external parameters). This theoretical groundwork, which should facilitate the design of more effective solutions, has now to be validated by further empirical research.

In this article we explore the limiting behavior of the universal prior distribution obtained when applied over multiple meta-level hierarchy of programs and output data of a computational automata model. We were motivated to alleviate the effect of Solomonoff's assumption that all computable functions or hypotheses of the same length are equally likely, by weighing each program in turn by the algorithmic probability of their description number encoding. In the limiting case, the set of all possible program strings of a fixed-length converges to a distribution of self-replicating quines and quine-relays - having the structure of a constructor. We discuss how experimental algorithmic information theory provides insights towards understanding the fundamental metrics proposed in this work and reflect on the significance of these result in digital physics and the constructor theory of life.

Intranasal (i.n.) administration became an alternative strategy to bypass the blood-brain barrier and improve drug bioavailability in the brain. The main goal of this work was to preliminarily study the biodistribution of mixed amphiphilic mucoadhesive nanoparticles made of chitosan-g-poly(methyl methacrylate) and poly(vinyl alcohol)-g-poly(methyl methacrylate) and ionotropically crosslinked with sodium tripolyphosphate in the brain after intravenous (i.v.) and i.n. administration to Hsd:ICR mice. After i.v. administration, the highest nanoparticle accumulation was detected in the liver, among other peripheral organs. After i.n. administration of a 10-times smaller nanoparticle dose, the accumulation of the nanoparticles in off-target organs was much lower than after i.v. injection. In particular, the accumulation of the nanoparticles in the liver was 20 times lower than by i.v. When brains were analyzed separately, intravenously administered nanoparticles accumulated mainly in the “top” brain, reaching a maximum after 1h. Conversely, in i.n. administration, nanoparticles were detected in the “bottom” brain and the head (maximum reached after 2 h) owing to their retention in the nasal mucosa and could serve as a reservoir from which the drug is released and transported to the brain over time. Overall results indicate that i.n. nanoparticles reach similar brain bioavailability, though with a 10-fold smaller dose, and accumulate in off-target organs to a more limited extent and only after redistribution through the systemic circulation. At the same time, both administration routes seem to lead to differential accumulation in brain regions and thus, they could be beneficial in the treatment of different medical conditions.

Dentin bonding is a key in restorative dentistry. Herein, we developed self-etching two-bottle adhesive system containing 10-methacryloyloxidecyl dihydrogen phosphate monomer (MDP) and the physical, mechanical, and biocompatible properties were evaluated. The characteristics of MDP were analyzed using nuclear magnetic resonance (NMR). The water sorption and solubility, the shear-bond strengths to dentin and enamel, and cytotoxicity tests were performed. The newly blended experimental group showed the lowest thickness and water sorption and solubility values. The shear bond strength to enamel and dentin were comparable to control groups (the three other products) all test groups showed 60% of cell viability. In this study, the properties of the newly synthesized adhesive are comparable with the others. The fundamental goal of this study is to get the MDP patent released, as it is intended for domestic production. For this purpose, this dentin adhesive was developed and compared with the commercial product.

In our recent works we reported that physical and chemical characteristics of serum can vary in relation to the psychic activity of an individual depending on whether it is oriented to stress or relaxation. We wandered if these observations could be accompanied by an appreciable modification of the Ph, electric conductivity and Delayed Luminescence of the same serum samples. Our preliminary data may suggest that the serum pH could significantly increase during a Relaxation Response intervention while electric conductivity seems to decrease. Moreover, Delayed Luminescense could vary in the same subject according to the Relaxation Response practice. According to our proof of concept study, we postulate the appearance of a coherent system within the blood samples analyzed after the Relaxation Response. Further researches and some technical development are needed to support our preliminary findings.

In the author's opinion, many global problems that face humanity - in the fields of education, medicine, management etc can be tackled more effectively if the cyclic nature of self-reproducing systems – including living beings – is taken into account. Summarizing the main physiological findings of the last decades on "adaptation reactions", one can very roughly say that the way of action which is effective in the sense of productive activity of people happens at the same time to be healthy, and it gives the participants of the process the feeling of happiness. The present paper represents a very short overview of the contemporary concepts of the adaptation reactions based on the fundamental understanding of their cyclic nature due to general properties of self-reproducing systems. One interesting feature of self-reproduction cycles is its first "phase of orientation" which was not discussed in detail in the past but plays a key role in the whole cycle.

Hierarchical honeycomb patterns were manufactured with the breath-figures self-assembly by drop-casting on the silicone-oil lubricated glass substrates. Silicone oil promoted spreading of the polymer solutions. The process was carried out with the industrial grade polystyrene and polystyrene with the molecular weight Mw=35.000. Both of polymers gave rise to the patterns, built from micro- and nano-scaled pores. Ordering of the pores was quantified with the Voronoi tessellations and calculating the Voronoi entropy. Measurement of the apparent contact angles evidenced the Cassie - Baxter wetting regime of the porous films.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

Health of migrant is a widely studied topic. It has been argued that migrant health may deteriorate over time. Though migrants are ‘a hard to reach’ population in survey data, this paper builds on a unique dataset provided by Médecins du Monde from five countries. We study self perceived health (SPH) in connection with socio-economic and demographic factors and length of stay. Results show different results for men and women. Asylum seekers compared to other documented migrants have a worse health. Migrants with better living conditions tend to be in better health. Employment and stable accommodation has a positive effect on SPH. Women from poorer countries have a better physical SPH after 3 months of residing in the host country. This paper contributes widely to knowledge of health of migrants. Contrarily to other evidence, health of migrants tends to improve for some migrants.

2-Hydroxypropyl-β-cyclodextrin (HPβCD) has unique properties to enhance the stability and the solubility of low water-soluble compounds by inclusion complexation. Understanding of the structural properties of HPβCD and its derivatives based on the number of 2-hydroxypropyl (HP) substituents at the a-D-glucopyranose subunits is rather important. In this work, replica exchange molecular dynamics simulations were performed to investigate the conformational changes of single- and double-sided HP-substitution called as 6-HPβCDs and 2,6-HPβCDs, respectively. The results show that glucose subunits in both 6-HPβCDs and 2,6-HPβCDs have lower chance to flip than in βCD. Also, HP groups are occasionally blocking the hydrophobic cavity of HPβCDs, thus hindering the drug inclusion. We found that HPβCDs with high number of HP-substitutions are more likely to be blocked, while HPβCDs with double-sided HP-substitution are even more probable to be blocked. Overall, 6-HPβCDs with three and four HP-substitutions are highlighted as the most suitable structures for guest encapsulation based on our conformational analyses such as structural distortion, radius of gyration, circularity and cavity self-closure of the HPβCDs.

It is shown that structuring at the microlevel is the intrinsic property of water and aqueous solutions. At room conditions water (including "ultrapure" one) and aqueous solutions are dispersed systems in which microcrystals of NaCl, surrounded by a layer of hydrated water (average diameter - 10-15 microns), are "elementary microparticles", which form the basis of the dispersed phase. Possible ways of formation of these microparticles and their evolution in the process of evaporation of unstructured part of water - dispersion medium - are considered. It is shown, in particular, that they are present in the air as aerosol contaminants. When the ionic strength of the solution increases, the water-salt particles coagulate, forming a new phase - coacervates, remaining on the substrate after evaporation of the liquid part of the water. The aggregates of coacervate structures, formed in a liquid medium, are disordered during heating, which can cause a change in a number of physicochemical properties of water at the temperatures of 50°-60°C range that have not been correctly explained in the framework of atomic-molecular concepts.

Nowadays, the research and development of on-chip LiDAR sensors for vehicle collision avoidance is growing very fast. Therefore, the assessment of the reliability in obstacle detection using the information provided by LiDAR sensors has become a key issue to be explored by the scientific community. This paper presents the design and implementation of a self-tuning method in order to maximize the reliability of an Internet-of-Things sensors network and to minimize the number of sensors to localize with the required accuracy obstacles by a detection threshold. In order to achieve this goal, models that predict accuracy (i.e., prediction error) for object localization using data collected by LIDAR sensors are designed and implemented in Webots Automobile 3D simulation tool. The approach is based on combining different techniques. Firstly, point-cloud clustering technique and an error prediction model library composed by a multilayer perceptron neural network with backpropagation, k-nearest neighbors and linear regression are explored. Secondly the above-mentioned techniques for modeling are also combined with a supervised and reinforcement machine learning technique, Q-learning in order to minimize the detection threshold. In addition, a IoT driving assistance simulated scenario with a LiDAR sensor network is designed in order to validate the prediction model and the optimal configuration of the sensor network to guarantee reliability in obstacle localization. The results demonstrate that the self-tuning method is appropriate to increase the reliability of the sensor network whereas minimizing the detection threshold

The proposal that the genetic code was formed on the basis of protein synthesis directed by tRNA dimers is reviewed and updated. The tRNAs paired through the anticodon loops are an indication on the process. Dimers are considered mimics of the ribosomes – structures that hold tRNAs together and facilitate the transferase reaction, and of the translation process – anticodons are at the same time codons for each other. The primitive protein synthesis system gets stabilized when the product peptides are able to bind the producers therewith establishing a self-stimulating production cycle. The chronology of amino acid encoding starts with Glycine and Serine, indicating the metabolic support of the Glycine-Serine C1-assimilation pathway, which is also consistent with evidence on origins of bioenergetics mechanisms. Since it is not possible to reach for substrates simpler than C1 and compounds in the identified pathway are apt for generating the other central metabolic routes, it is considered that protein synthesis is the beginning and center of a succession of sink-effective mechanisms that drive the formation and evolution of the metabolic flow system. Plasticity and diversification of proteins construct the cellular system following the orientation given by the flow and implementing it. Nucleic acid monomers participate in bioenergetics and the polymers are conservative memory systems for the synthesis of proteins. Protoplasmic fission is the final sink-effective mechanism, part of cell reproduction, guaranteeing that proteins don’t accumulate to saturation, which would trigger inhibition.

Background/Objectives: The aim of this study is the operationalization of the International Classification of Functioning, Disability and Health in the rehabilitation care performed at the Institute of Cancer of the State of São Paulo through structuring a goal-oriented tool with relevant categories of evaluation and follow-up for cancer outpatients to be applied by physiatrists, physiotherapists, physical educators, occupational therapists, and psychologists. Methods: A qualitative study based on a literature review and a modified Delphi exercise, Estimate-Talk-Estimate (ETE) technique, was performed with the service’s rehabilitation experts. Consensus was obtained after four rounds under the 80% agreement threshold. Results: Forty categories were identified for neuropsychological evaluation and thirty-three for psychoaffective support, with 12 goals. Thirty-five categories with 13 goals were accounted for physiotherapy. Physical educators identified 18 categories, with 7 goals. Occupational therapists selected 54 categories, with 10 goals. A referral for personal factors was established. Functional Assessment of Cancer Therapy-General (FACT-G) was the quality of life tool chosen to be applied. Conclusions: A set of relevant ICF categories was structured, tailored by a clinically meaningful routine of assessment and follow-up of cancer outpatients based on specialists’ clinical practice and scientific literature. It will contribute for analyzable and more specific and quantifiable institutional health data. Its implementation and future discussion may promote the instrument’s refinement for its use in this population.

BackgroundLiving donor liver transplantation offers comparable long-term results to cadaveric donor transplantation. This study analyzes the selection process of living liver donors at a Western transplant center that utilizes both donation forms. MethodsThis retrospective analysis examined potential living donors, collecting medical data and reasons for refusal, and divided patients by indication and urgency for transplantation. ResultsFrom January 2013 to December 2023, 594 potential living donors were assessed at Jena University Hospital. Of these, 124 living donor transplants were performed. During outpatient evaluation, 357 potential donors were excluded. Subsequently, 238 individuals underwent inpatient assessment, with 100 more being excluded. Main reasons for donor refusal included medical or psychological issues (n=160), disease progression in recipients (n=90), and recipient refusal or donor withdrawal (n=54). The evaluation process showed a trend towards considering more distant relatives and acquaintances as donor candidates with increasing severity of the recipient's disease.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Australia’s mental health system is failing young people. Calls for accountability, strategic long-term policy planning, and regional leadership have been identified as solutions to guide mental health reform. Developing system dynamics models using a participatory approach (participatory systems modelling, PSM) is recognised as a useful method that can support decision-making for strategic reform. This paper reports evaluation findings of a youth mental health PSM process conducted in the Australian Capital Territory (ACT). Baseline and follow-up mixed-methods evaluation data were collected in 2022 across diverse stakeholder groups to investigate the feasibility, value, impact, and sustainability of PSM. Though youth mental health system reform was viewed as desirable and a necessity across all stakeholder groups, shared perceptions of disabling powerless was observed regarding their ability to influence current decision-making processes to improve the youth mental health system. This suggests greater accountability is required to support systemic reform in youth mental health. PSM offers promise in improving transparency and accountability of decision-making for youth mental health as exemplified in the ACT. However, more support and time are required to facilitate transformational change. Future research should investigate empowerment strategies to complement the implementation of findings from dynamic models developed through PSM, as well as the effectiveness of regional youth mental health policy decision-making supported by systems modelling.

This research experiments with a sustainability assessment based on the Sustainable Development Goals (SDGs) of Agenda 2030 through a process of their territorialisation and implementation. This process enables the development of a Spatial Decision Support System (SDSS) that can be integrated with strategic environmental assessments in urban planning. The assessment takes place on the transversality of the sustainability concept by trying to consider together the three dimensions (environmental, social and economic) into a single assessment through the Spatial Sustainability Assessment Model (SSAM) by integrating Geographic Information Systems (GIS) and multi-criteria analyses. Economic development, social equity, and ecological integrity represent three common visions for rethinking peri-urban edges.

The research presents the Methodology of Improving the Accuracy in Text Classification in Light of Modelling the Latent Semantic Relations (LSR). The aim of this Methodology is to find the ways of eliminating the Limitations of Discriminant and Probabilistic methods for LSR revealing and customizing the Text Classification Process to the more accurate recognition of the text tonality. This aim should be achieved by using the knowledge about the text’s Hierarchical Semantic Context in the form of Corpora-based Hierarchical Sentiment Dictionary. The main scientific contribution of this research is the following set of approaches to improve the qualitative characteristics of Text Classification process: combination of the Discriminant and Probabilistic methods allowing to decrease the influences of the Limitations of these methods on the LSR revealing process; considering each document as a complex structure allowing to estimate documents integrally by separated classification of topically completed textual component (paragraphs); taking into account the features of Argumentative type of documents (Reviews) allowing to use the author’s subjective evaluation of text tonality for development the Text Classification methodology. Tonality, expressed by the Review’s author, has a significant, but not critical, effect on the qualitative indicators of Sentiment Recognition.

Current theories of autoimmunity are diverse, sometimes contradictory, and suffer from incompleteness. Although substantial evidence exists that adaptive and innate immunity, sex, genetic predisposition, and the microbiome all play essential roles in autoimmune disease etiologies and pathogenesis, and that antigen processing is altered during disease induction, no existing theory integrates all of these factors through a single, coherent mechanism. In an attempt to focus the field on the need to elucidate such an integrative mechanism, I propose one possibility here that, if nothing else, helps to identify the nature of the problems that need to be addressed. My theory is that autoimmune diseases are induced by normal immunological responses to unique pairs of complementary antigens, at least one of which is a molecular mimic of a host target. Each antigen in the complementary pair induces a complementary immune response (T or B cell); although each immune response is idiotypic in origin, the antigenic complementarity results in what appears to be an idiotype-anti-idiotype relationship between the responses. Additionally, because of the antigenic complementarity, each immune response mimics one of antigens, abrogating the distinction between self and non-self. If at least one of the antigens mimics a host antigen, then the resulting immunological civil war spreads to a host tissue. Complementary antigens also alter antigen processing so that antigens that would normally be proteolytically digested are presented by the major histocompatibility complex (MHC) to T and B cell receptors inducing a cross-reactive immune response. The resulting civil war is supported by the innate immune system due to the complementarity of the initiating antigens.. Complementary antigens stimulate synergistic toll-like receptors (TLR) and/or nucleotide-binding oligomerization receptors (NOD) resulting in up-regulation of cytokine production and further stimulation of the adaptive immune response. Because the immune responses (e.g., antibodies) mimic the initiating antigens, this synergistic activation of innate immunity becomes chronic. Additionally, TLR and NOD function are highly sensitive to sex hormones, some becoming up-regulated and some down-regulated in the presence of either testosterone or estrogens. This sensitivity explains how sex modifies susceptibility to autoimmune diseases. Genetic mutations in TLR, NOD and MHC further alter antigen presentation and the degree to which antigens stimulate an immune response explaining how genetics also modifies susceptibility. Finally, sex hormones also alter the host microbiome, which in turn modulates autoimmune disease risk by shaping the immunological nature of self and by mediating susceptibility to microbial infection. Moreover, it appears that the microbiome camouflages itself from the immune system by mimicking the host antigenic repertoire; the mimicry between the antigens of the microbiome and the host results in selective attacks on microbiome constituents concomitant with any autoimmune attack on host tissues. This antigenic complementarity theory thereby integrates all major elements known to affect, or be affected by, autoimmune diseases and provides a set of testable implications.

This study explored the effectiveness of a virtual music therapy program, based on positive psychotherapy principles, for college students during the COVID-19 pandemic. Twenty-four undergraduate students with partial PTSD were initially assigned to either an experimental group or a control group, with 11 participants in each group by the study's end. The experimental group underwent 15 video sessions of the therapy program, completing one session per weekday over three weeks. The program involved worksheets targeting goals aligned with positive psychology, such as positive affect, life meaning, personal strengths, gratitude, hope, and happiness. Activities included writing music autobiographies, creating and analyzing song lyrics, and exploring various music pieces. The effectiveness of the intervention was measured using the 21-item Depression Anxiety Stress Scale and the Korean Version of Positive Psychological Capital (K-PPC) before, immediately after, and three weeks post-program. The experimental group showed significant improvements in stress, anxiety, depression, self-efficacy, resilience, and the K-PPC total score compared to the control group. These improvements were maintained at the three-week follow-up. The findings suggest that positive psychology-based virtual music therapy can significantly enhance the mental health of highly stressed college students, especially during challenging times like the COVID-19 pandemic.

: This study aimed to validate the effects of self-compassion-based forest healing therapy as an intervention for reducing stress and promoting coping resources. Therefore, we investigated the effects of self-compassion-based forest healing therapy on stress, self-compassion, and connectedness to nature. A total of 30 participants were divided into an experimental and control group. Two sessions of forest healing meditation activities were held at the Forest of Healing every two weeks between October and November 2023. As a repeated measures experiment, data were collected before the intervention, after the first intervention, and after the second intervention. Perceived stress, positive and negative affect, and salivary cortisol were measured to assess physiological and psychological stress in participants. Connectedness to nature and self-compassion were measured to evaluate stress-coping resources. The results showed that the forest healing program had significant positive effects on stress and emotional states in the experimental group after the intervention. Further, there was a significant incremental effect on connectedness to nature and self-compassion in the experimental group. Therefore, self-compassion meditation-based forest healing therapy is a feasible and efficient approach for facilitating stress management and coping resource building.

A theoretical account of development in mesocortical anatomy is derived from the free energy principle, operating in a neural field with both Hebbian and anti-Hebbian neural plasticity. An elementary structural unit is proposed, in which synaptic connections at mesoscale are arranged in paired patterns with mirror symmetry. Exchanges of synaptic flux in each pattern form coupled spatial eigenmodes, and the line of mirror reflection between the paired patterns operates as a Markov blanket, so that prediction errors in exchanges between the pairs are minimized. The theoretical analysis is then compared to the outcomes from a biological model of cortical neurodevelopment, in which neuron precursors are selected by apoptosis for cell body and synaptic connections maximizing synchrony and also minimizing axonal length. It is shown that this model results in patterns of connection with the anticipated mirror symmetries, at micro-, meso- and inter-arial scales, among lateral connections, and in cortical depth, explaining the spatial organization and functional significance of neuron response preferences, and compatible with features of both columnar and noncolumnar cortex. Multi-way interactions of mirrored representations provide a preliminary anatomically realistic model of cortical information processing.

This article introduces existential wellbeing (EWB) as one of the most ignored but also the most important kind of wellbeing, especially for people who experience life-limiting diseases and need palliative care (Wong & Yu, 2021). This article will not only review the literature regarding the nature and practice of existential wellbeing in palliative care, but also propose a preliminary Existential Wellbeing Scale. EWB is defined as the quality-of-life characterized by living well and dying well in spite of pain, obstacles, and the shadow of death; wellbeing within the context of human suffering can only be fully understood from the perspective of existential positive psychology (EPP), dedicated to the study of sustainable wellbeing based on the foundation of transcending suffering. The basic tenets of EPP are (1) redefining positivity or wellbeing in terms of seeing and being the light in the darkness; (2) focusing on the dialectical process of navigating an adaptive balance; and (3) re-orienting one’s life attitude from egotism to self-transcendence (Wong, 2023a). More specifically, EWB depends on some combination of the following experiences: (1) Prior experience of overcoming adversity; (2) Existential intelligence (Gardner, 2020) in addressing existential concerns; (3) Existential wisdom of the soul (Wong 2022a; Wong, Ho, et al, 2023a) to achieve existential wellbeing and sustainable flourishing; (4) Spiritual wellbeing based on spiritual values such as faith, hope, and love (Wong, 2023); (5) Knowledge of meaning-focused coping (Eisenbeck et al., 2021); and (6) The new paradigm of self-transcendence (Reed & Haugan, 2021; Wong, Arslan et al., 2021; Wong, Ho et al., 2023b) to transcend and transform suffering into wellbeing and triumph.

Matter grows and self-assembles to produce complex structures such as virus capsids, carbon fullerenes, proteins, glasses, etc. Due to its complexity, performing pen-and-paper calculations to explain and describe such assemblies is cumbersome. Many years ago, Richard Kerner presented a pen-and-paper path integral approach to understand self-organized matter. Although successfully addressed many important problems including the yield of fullerene formation, the glass transition temperature of doped chalcogenide glasses, the fraction of boroxol rings in B2O3 glasses, the first theoretical explanation for the empirical recipe of window and Pyrex glass and the understanding of virus capsid self-assembly, still is not the primary choice when tackling similar problems. The reason lies in the fact that it diverges from mainstream approaches based on the energy landscape paradigm and non-equilibrium thermodynamics. In this context, a critical review is presented, demonstrating that the Richard Kerner method is, in fact, a clever way to identify relevant configurations. Its equations are simplified, common physical sense versions to those found in the energy landscape kinetic equations. Subsequently, the utilization of equilibrium Boltzmann factors in the transition Markov chain probabilities is analyzed within the context of local two-level energy landscape models kinetics. This analysis demonstrates that their use remains valid when the local energy barrier between reaction coordinate states is small compared to the thermal energy. This finding places the Richard Kerner model on par with other more sophisticated methods and, hopefully, will promote its adoption as an initial and useful choice for describing the self-agglomeration of matter.

The impact of the COVID-19 pandemic and the quarantine measures on children and adolescents’ hospitalization psychiatric has been poorly studied, especially in Italy, the first European country to adopt social restrictions. To fill this gap, this retrospective study examined changes in admissions to our child and adolescent psychiatry ward from the emergency department during the two COVID-19 quarantine periods in Italy (March to June 2020; October 2020 to January 2021) compared with two reference periods (defined as 12 months prior to the respective quarantine periods). Specifically, we examined data on the number of inpatients and the distribution of psychopathological disorders (i.e., psychosis, mood disorder) and self-injurious behaviors. The results revealed significantly fewer admissions during the first quarantine period relative to the first reference period and, conversely, significantly more admissions during the second quarantine period relative to the second reference period. Of note, the results showed an increased frequency of mood disorders, non-suicidal self-injurious behaviors and suicidal ideation during the quarantine periods, compared to the reference periods. The findings underline the need to focus on the psychopathological profile of children and adolescents with patient-tailored therapeutic interventions and suggest the importance of developing psychological healthcare services for future emergency periods..

Research on image-inpainting tasks has mainly focused on enhancing performance by augmenting various stages and modules. However, this trend does not consider the increase in the number of model parameters and operational memory, which increases the burden on computational resources. To solve this problem, we propose a Parametric Efficient Image InPainting Network (PEIPNet) for efficient and effective image-inpainting. Unlike other state-of-the-art methods, the proposed model has a one-stage inpainting framework in which depthwise and pointwise convolutions are adopted to reduce the number of parameters and computational costs. To generate semantically appealing results, we selected three unique components: spatially-adaptive denormalization (SPADE), dense dilated convolution module (DDCM), and efficient self-attention (ESA). The SPADE was adopted to conditionally normalize activations according to the mask to distinguish between damaged and undamaged regions. The DDCM was employed at every scale to overcome the gradient-vanishing obstacle and gradually fill-in pixels by capturing global information along the feature maps. The ESA was utilized to obtain clues from unmasked areas by extracting long-range information. In terms of efficiency, our model has the lowest operational memory compared with other state-of-the-art methods. Both qualitative and quantitative experiments demonstrate the generalized inpainting of our method on three public datasets: Paris StreetView, CelebA, and Places2.

Neurodegeneration is becoming one of the leading causes of death worldwide as the population expands and grows older. There is a growing desire to understand the mechanisms behind prion proteins as well as the prion-like proteins that make up neurodegenerative diseases (NDs) including Alzheimer’s Disease (AD). Both amyloid β (Aβ) and hyperphosphorylated tau (p-tau) proteins behave in ways similar to that of the infectious form of the prion protein, PrPSc, such as aggregating, seeding, and replicating under not yet fully understood mechanisms, thus the designation of prion-like. This review aims to highlight the shared mechanisms between prion-like proteins and prion proteins in the structural variations associated with aggregation and disease development. These mechanisms are largely focusing on the dysregulation of protein homeostasis, self-replication, and protein aggregation, and how this knowledge could contribute to diagnoses and treatments for the given NDs.

The vast majority of autonomous driving systems are limited to applications on roads with clear lane markings and are implemented using commercial grade sensing systems coupled with specialized graphic accelerator hardware. This research reviews an alternative approach for autonomously steering vehicles that eliminates the dependency on road markings and specialized hardware. A combination of machine vision, machine learning and artificial intelligence based on popular pre-trained Convolutional Neural Networks (CNN) and Recurrent Neural Networks (RNN) was used to drive a vehicle along roads lacking lane markings (unmarked roads). The team developed and tested this approach on the ACTor (Autonomous Camus TranspORt) vehicle - an autonomous vehicle development and research platform coupled with a low-cost webcam based sensing system and minimal computational resources. The proposed solution was evaluated on real-world roads and varying environmental conditions. It was found that this solution may be used to successfully navigate unmarked roads autonomously with acceptable road following behavior.

Durability of concrete requires a dense microstructure which can be achieved by using self-compacting concrete (SCC). Both calcined clay (CC) and rice husk ash (RHA) are promising supplementary cementitious materials (SCMs) that can partially replace cement, but their use in SCC is critical due to their higher water demand and specific surface area (SSA) compared to cement. Empirical method of SCC design was adopted considering the physical properties of both CC and RHA. The influence of partially substituting cement at 20 vol-% with binary and ternary blends of CC and RHA were investigated. The fresh properties of SCC were investigated using a variety of tests. The time dependent workability was monitored by plunger method and flow resistance determined based on the rheological measurements of SCC. The evolution of the hydrate phases of the binder in SCC was determined by thermogravimetric analysis, while the durability was evaluated by rapid chloride migration test. Cement partial replacement with 20 vol-% CC has no significant effect on SCC fresh, time dependent, compressive strength and durability properties. 20 vol-% RHA on the other hand requires higher dosage of SP to achieve self-compactability and increased the viscosity of SCC. Its workability retention is only up to 30 min after mixing and exhibited higher flow resistance. It consumes more CH and improves compressive strength and chloride resistance of SCC. The ternary blending with CC and RHA yielded better fresh SCC properties compared to the binary blend with RHA, while an improved chloride penetration resistance could be achieved compared to binary CC blend.

The multivariate Gaussian random fields with matrix-based scaling laws are widely used for inference in statistics and many applied areas. In such contexts interests are often in symmetry and in the rates of change of spatial surfaces in any given direction. This article analyzes the almost sure sample function behavior for operator fractional Brownian motion, including multivariate fractional Brownian motion. We obtain the estimations of small ball probability and the strongly locally nondeterministic for operator fractional Brownian motion in any given direction. Applying these estimates we obtain Chung's laws of the iterated logarithm for spatial surfaces of operator fractional Brownian motion. Our results show that the precise rates of change of spatial surfaces are completely determined by the self-similarity exponent.

The ability to self-direct a research program determines graduate degree completion. Yet, research on incompletion of graduate physics programs assume students’ present level of self-direction adequate and neglects to recognize a lack of self-directed learning as key. One theoretical mathematical physicist focused on changing this challenge of physics graduate education by promoting self-directed learning through the type research flow that has been found to bring the greatest satisfaction to researchers with respect to their insights. This he provided through his space, time, open mindedness and theoretical contributions with his students and in collaboration with his colleagues. A self-directed learner himself, David J. Rowe developed methods of mentoring for encouraging physics graduate students to recognize symmetry as valuable in identifying solutions to problems quickly—helping these students take the lead in finding insightful resolutions to complex, multidimensional, mathematical physics uncertainties. How Rowe set about supporting self-directed learning in his graduate physics education interactions will be examined with the use of narrative research to interpret the texts and conversations with the author he made available. His techniques will be presented and recommendations made regarding how Rowe’s work in this regard can be modeled to improve self-direction in STEM graduate education.

Branching patterns are ubiquitous in nature, consequently over the years many researchers have tried to characterize the complexity of their structures. Due to their hierarchical nature and resemblance to fractal trees, they are often thought to have fractal properties, however their non-homogeneity (i.e., lack of strict self-similarity) is often ignored. In this paper we review and examine the use of the box-counting and sandbox methods to estimate the fractal dimensions of branching structures. We highlight the fact that these methods rely on an assumption of self-similarity that is not present in branching structures due to their non-homogeneous nature. Looking at the local slopes of the log-log plots used by these methods reveals the problems caused by the non-homogeneity. Finally, we examine the role of the canopies (endpoints or limit points) of branching structures in the estimation of their fractal dimensions.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

A sustainable solution for crack maintenance in geopolymers is necessary if they are to be the future of modern green construction. This study thus aimed to develop self-healing biogeopolymers that could potentially rival bioconcrete. First, a suitable healing agent was selected from Bacillus subtilis, B. sphaericus, and B. megaterium by directly adding their spores in the geopolymers and subsequently exposing them to a large amount of nutrients for 14 days. SEM-EDX analysis revealed the formation of biominerals for B. subtilis and B. sphaericus. Next, the effect of biochar-immobilization and co-culturing (B. sphaericus and B. thuringiensis) on the healing efficiencies of the geopolymers were tested and optimized by measuring their ultrasonic pulse velocities weekly over a 28-day healing period. The results show that using co-cultured bacteria significantly improved the observed efficiencies, while biochar-immobilization had a weak effect but yielded an optimum response between 0.3-0.4 g/mL. The maximum crack width sealed was 0.65 mm. Through SEM-EDX and FTIR analyses, the biominerals precipitated in the cracks were identified to be mainly CaCO3. Furthermore, image analysis of the XCT scans of some of the healed geopolymers confirmed that their pulse velocities were indeed improving due to the filling of their internal spaces with biominerals. With that, there is potential in developing self-healing biogeopolymers using biochar-immobilized spores of bacterial cultures.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

In recent years, the individualized demand of customers brings small batches and diversification of orders towards enterprises. The application of enabling technologies in factory, such as the Industrial Internet of Things (IIoT) and Cloud Manufacturing (CMfg), enhances the ability of customer requirement automatic elicitation and the manufacturing process control. The job shop scheduling problem with random job arrival time dramatically increases the difficulty in process management. Thus, how to collaboratively schedule the production and logistics resources in the shop floor is very challenging, and it has a fundamental and practical significance of achieving the competitiveness for an enterprise. To address this issue, the real-time model of production and logistics resources is built firstly. Then, the task entropy model is built based on the task information. Finally, the real-time self-adaption collaboration of production and logistics resources is realized. The proposed algorithm is carried out based on a practical case to evaluate its effectiveness. Experimental results show that our proposed algorithm outperforms three existing algorithms.

Background: Parents of preterm infants face major mental health challenges in the Neonatal Intensive Care Unit (NICU). Family-centered music therapy actively integrates and empowers parents in their infant’s care. With the aim to better understand and address parental needs separately from their babies’, a music therapy (MT) self-care group was implemented as part of clinical practice at the hospital Clínica de la Mujer in Bogotá, Colombia. Methods: The group is provided for both parents twice a week in the NICU. Music guided relaxations, breathing techniques, and self-expression are at the center of the MT group sessions. Parents complete a pre/post self-administered Numeric Rating Scale (NRS) including anxiety levels, stress levels, mood and motivation. Results: Parents highly value the MT self-care group at the NICU. On average there is a 37% improvement in anxiety levels, 28% in stress levels, and 12% in mood, restfulness and motivation. Being able to relax, to distract themselves from their worries and having time for themselves are amongst the most frequently mentioned benefits. Conclusions: Addressing parents’ needs separately form their babies’ treatment with culturally sensitive interventions aimed to improve parental mental health, is essential for continuing the development of family-centered music therapy interventions in the NICU.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

This study explores individual and contextual risk factors for the onset of work interfering with private life (WIL) and private life interfering with work (LIW) among self-employed men and women across European countries. It also studies the relationship between interference (LIW and WIL) and wellbeing among self-employed men and women and the effect of macro level risk factors. Data from the fifth round of European Working Conditions Survey was utilized and a sample of self-employed men and women with active businesses was extracted. Applying multilevel regressions, results show that though business characteristics are important for level of WIL, time demand is the most evident risk factor for WIL and LIW. There is a relationship between wellbeing and WIL and LIW respectively, and time demands is the most important factor in this relationship. Gender equality on the labor market did not relate to level of interference, nor did it mediate the relationship between interference and wellbeing. However, the main and most important risk factor for experiencing WIL and LIW and for how interference relate to wellbeing is gender relation processes in work and life, both on individual and contextual level.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

Serious damage caused by floor heave in the coal given chamber of a vertical coal bunker is one of the challenges faced in underground coal mines. Engineering practice shows that it is more difficult to maintain the coal given chamber (CGC) than a roadway. More importantly, repairing the CGC during mining practice will pose major safety risks and reduce production. Based on the case of the serious collapse that occurred in the bearing structure of the CGC at the lower part of the 214# coal bunker in Xiashijie mine, China, this work analysed (i) the main factors influencing floor heave and (ii) the failure mechanism of the load-bearing structure in the CGC using FLAC^2D numerical models and expansion experiment. The analysis results indicate that: the floor heave, caused mainly by mine water, is the basic reason leading to the instability and repeated failure of the CGC in the 214# coal bunker. Then a new coal bunker, without building the CGC, is proposed and put into practice to replace the 214# coal bunker. The FLAC^3D software program is adopted to establish the numerical model of the wall-mounted coal bunker (WMCB), and the stability of the rock surrounding the WMCB is simulated and analysed. The results show that: (1) the rock surrounding the sandstone segment is basically stable. (2) The surrounding rock in the coal seam segment, which moves into the inside of the bunker, is the main zone of deformation for the entire rock mass surrounding the bunker. Then the surrounding rock is controlled effectively by means of high-strength bolt–cable combined supporting technology. According to the geological conditions of the WMCB, the self-bearing system, which includes (i) H-steel beams, (ii) H-steel brackets, and (iii) self-locking anchor cables, is established and serves as a substitute for the CGC to transfer the whole weight of the bunker to stable surrounding rock. The stability of the new coal bunker has been verified by field testing, and the coal mine has gained economic benefit to a value of 158.026174 million RMB over three years. The new WMCB thus made production more effective and can provide helpful references for construction of vertical bunkers under similar geological conditions.

Many clinical research datasets have a large percentage of missing values that directly impacts their usefulness in yielding high accuracy classifiers when used for training in supervised machine learning. While missing value imputation methods have been shown to work well with smaller percentages of missing values, their ability to impute sparse clinical research data can be problem specific. We previously attempted to learn quantitative guidelines for ordering cardiac magnetic resonance imaging during the evaluation for pediatric cardiomyopathy, but missing data significantly reduced our usable sample size. In this work, we sought to determine if increasing the usable sample size through imputation would allow us to learn better guidelines. We first review several machine learning methods for estimating missing data. Then, we apply four popular methods (mean imputation, decision tree, k-nearest neighbors, and self-organizing maps) to a clinical research dataset of pediatric patients undergoing evaluation for cardiomyopathy. Using Bayesian Rule Learning (BRL) to learn ruleset models, we compared the performance of imputation-augmented models versus unaugmented models. We found that all four imputation-augmented models performed similarly to unaugmented models. While imputation did not improve performance, it did provide evidence for the robustness of our learned models.

As a complementary and alternative medicine in the western countries for decades, traditional Chinese medicine (TCM) has been used for more than 2000 years in China. Because of the characteristics of the philosophical style and the unknown mechanism of action, TCM sometimes has been biasedly described as "fraught with pseudoscience". From the scientific basis of the systems biology, here we promoted a novel medical model called the entropic systems medicine which could be applied to scientize TCM in future. In entropic systems medicine, TCM and Western modern biomedicine target the different variables of the entropic system. For instance, while Western modern biomedicine directly targets the phenotypes and its SOCs of macrostates, TCM differently targets the microstates, entropy and entropic force to generate SOTFs gradually causing the differentiated syndromes to be slowly rearranged. The prerequisites to modernize TCM are the entropic systems biology having been well established so that the variables could be precisely monitored and mathematically calculated.

In this paper, intrusion detection systems are thoroughly investigated utilizing the CSE-CIC-IDS-2018 dataset. The research is divided into three key phases: first, applying Data Cleaning, Exploratory Data Analysis, and Data Normalization techniques (min-max and z-score) for preparing data across distinct classifiers. Second, feature importance is reduced using a combination of Principal Component Analysis (PCA) and Random Forest (RF), with the goal of improving processing speed and decreasing model complexity. This stage comprises a comparison with the entire dataset. Finally, machine learning algorithms (XGBoost, CART, DT, KNN, MLP, RF, LR, and Bayes) are applied to specific features and preprocessing approaches. Surprisingly, the XGBoost, DT, and RF models outperform in both ROC values and CPU runtime. Following evaluation, which includes PCA and RF feature selection, an optimal set is produced.

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

Energy transition is a major structural change in the whole social system, and the energy system must be changed globally to replace fossil fuels. Hydropower is one of the largest renewable energy in the world. However the involuntary resettlees due to the construction of hydropower projects are suffering from being far away from their native land, losing the land cultivated for generations and the houses they live in, and losing the social relationship network based on geography and blood ties. Based on the system evaluation theory of reservoir resettlement and referring to relevant research findings, this paper constructs a comprehensive evaluation index framework for assessing the implementation effect of the PostRelocation Support (PReS) policy. The research region is located in Zhijin County, Bijie City, Guizhou Province, China. Accordingly, a combined method of a structural equation model and a fuzzy comprehensive evaluationary model is used in this paper to analyze the implementation of the PReS policy. The results show that the total score of implementing effects of the PReS policy is 4.4, with dramatic significance. The subindex scores of the resettlers’ family income, living conditions, and production conditions; the local economy; and social stability are 4.3, 4.6, 4.4, 4.6, and 4.3, respectively, with dramatic significance. This paper has analyzed and summarized the successful practices of implementing the PReS policy for reservoir resettlers in three dimensions: poverty alleviation, beautiful home construction and accelerating rural revitalization. Research shows that China's rural reservoir resettlers' PReS policy has been more effective in restoring the livelihoods of reservoir resettlers.

The airline sector is critical in today's globalized society, supporting the efficient movement of people and products worldwide. Airlines are continuously looking for methods to enhance their operational performance to remain competitive in the face of increased competition. This study focuses on the application of Multi-Criteria Decision Making (MCDM) techniques to improve low-cost carrier (LCC) also known or low-cost (budget) airlines' ground operational performance. MCDM techniques have gained considerable attention in recent years to address complex decision problems with multiple conflicting goals. This research aims to bridge this gap by proposing a comprehensive framework that combines MCDM techniques to enhance airline operational strategies to increase performance. The study utilizes qualitative and quantitative data, drawing on previously published materials on MCDM techniques in the aviation sector. It utilizes fuzzy Analytic Hierarchy Process (AHP) and fuzzy Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) methodologies. A case study is conducted to evaluate the ground operational performance of three airline companies based in Türkiye, considering five main criteria and 18 sub-criteria. The findings of this research will contribute to a comprehensive understanding of operational performance in the airline sector. It also highlights the implications and limitations of the research and suggests future research directions.

The article presents a new scalable iterative method for linear programming called the “apex method”. The key feature of this method is constructing a path close to optimal on the surface of the feasible region from a certain starting point to the exact solution of linear programming problem. The optimal path refers to a path of minimum length according to the Euclidean metric. The apex method is based on the predictor-corrector framework and proceeds in two stages: quest (predictor) and target (corrector). The quest stage calculates a rough initial approximation of linear programming problem. The target stage refines the initial approximation with a given precision. The main operation used in the apex method is an operation that calculates the pseudoprojection, which is a generalization of the metric projection to a convex closed set. This operation is used both in the quest stage and in the target stage. A parallel algorithm using a Fejér mapping to compute the pseudoprojection is presented. An analytical estimation of the parallelism degree of this algorithm is obtained. Also, an algorithm implementing the target stage is given. The convergence of this algorithm is proven. An experimental study of the scalability of the apex method on a cluster computing system is described. The results of applying the apex method to solve problems from the Netlib-LP repository are presented.

Prefabricated forms of construction have led to the rapid onsite assembly of buildings however there are still on-site tasks and processes which can be reevaluated and redone specifically in keeping with the principles of prefabrication instead being adapted to fit its purpose. One such process is that of waterproofing between prefabricated panels and modules which come from the factory fully complete façade and all. Conventional means of waterproofing can be used however it results in more work done on site, potential delays and generally requires access from the external face of the building. This paper presents the Modelling, Implementation and Evaluation of purpose developed weatherproof seals specific for Prefabricated Construction. An overview is provided of the entire development process and specific focus is given to the modeling using FEA computer simulations, manufacturing and testing which then resulted in the implementation in a prefabricated panelised building which is used as a case study and the means of further evaluation. These strategies have enabled an efficient and robust prefabricated waterproofing solution specific for this form of construction to be understood and implemented. The resulting case study has successfully verified the time and cost savings when compared to conventional techniques whilst still providing a durable and effective weatherproof seal for prefabricated panelised and modular systems.

Differential Evolution (DE) is an evolutionary algorithm that has become increasingly popular due to its effectiveness and efficiency. However, its adaptation for multi-objective optimization requires further investigation. To address this issue, a novel algorithm called ILSDEMO has been proposed, which incorporates indicator-based selection and local search into a self-adaptive DE. ILSDEMO employs an archive population to store non-dominated solutions, generating an initial population uniformly distributed over the feasible solution space using orthogonal design. Additionally, two variants of DE are used to expedite convergence, while q-Gaussian mutation is utilized to exploit better trial individuals. The k-nearest neighbor rule is used to eliminate crowded solutions, and indicator-based selection is employed to generate a new parent population without diversity preservation. The performance of ILSDEMO was investigated on the test instances from the ZDT series and DTLZ series in terms of the selected indicators. The results suggest that ILSDEMO accurately and evenly approximates the true Pareto front compared to NSGAII, IBEA, and DEMO.

This study considers ways to increase the consumption of sustainable fashion, given the significant environmental and social damages, associated with the industry. A series of experiments were conducted examining the impacts of choice architecture (nudges) under field conditions in collab-oration with one of Israel’s largest shopping centers. The study sought to identify which inter-ventions at the retail level successfully motivate sustainable fashion behavioral change regarding purchases and willingness to pay more, along with agreement with several statements regarding the climate crisis and sustainable fashion. Among the types of nudges examined in this field study were providing information, increasing accessibility to sustainable alternatives and appealing to social identity, in relation to demographics and green self-image. The study found that offering alterna-tives to consumers constitutes the most effective way to “nudge” consumers toward more sus-tainable purchasing behavior. Nonetheless, this does not negate the contribution of providing in-formation and strengthening social norms regarding sustainable fashion. Additionally in all groups, most participants reported that they do not know how to distinguish between sustainable and non-sustainable fashion, nor do they believe that the clothes they purchased were actually sustainable. The findings emphasize the need for policies that will increase the accessibility of sustainable fashion.

An innovative concrete that incorporates the advantages of self-compacting concrete with geopolymer is called self-compacting geopolymer concrete. The objective of this study was the Manufacturing of M30-grade self-compacting geopolymer concrete by adding industrial materials like fly ash (FA), ultrafine ground granulated blast furnace slag (UFGGBS), and silica fume (SF) as minerals. The disposal of these industrial wastes can be substantially overcome, as they lead to land pollution. The fixed powder content was 500 kg/m³. A mixture of sodium silicate (Na₂SiO₃) and sodium hydroxide (NaOH) created an alkaline solution that activated the cementitious binders. In this study, slump flow, L-box, V Funnel, T50 V Funnel, and J ring tests were carried out to determine the fresh qualities of the concrete. These tests were conducted under the regulations for self-compacting concrete provided by EFNARC (2005). To improve the flexural strength of the SCGC, 1.5 % glass fibre was added. This study illustrates how an artificial neural network (ANN) model can determine the concrete mix proportion. The characteristics of SCGC, both fresh and hardened properties test were investigated for molarities of 8, 10, and 12. The microstructural outcomes were determined using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and X-ray diffraction (XRD).

The prolonged static sitting at the workplace is considered as one of the main risks for development of musculoskeletal disorders (MSDs) and adverse health effects. Factors such as poor posture and extended sitting are perceived to be a reason for conditions such as lumbar hyperlordosis and lower back pain (LBP), even though the scientific explanation of this relationship is still unclear and raises disputes in the scientific community. This publication proposes the low back pain assessment (LBPA) dataset collected through experiment with 100 participants and consisting of photogrammetric images with intentionally placed body markers, calculated postural angles and tags correct and incorrect posture assessed by habilitated rehabilitator, as well as questionnaire-based self-reports regarding the occurrence of LBP and similar symptoms among the participants. Machine learning models trained with this data are employed for recognizing incorrect body postures. Two scenarios have been elaborated for modeling purposes: scenario 1, based on natural body posture tagged as correct and incorrect, and scenario 2, based on incorrect body postures, corrected additionally by the rehabilitator. The achieved accuracies of respectively 75.3% and 85% for both scenarios reveal the potential for future research in enhancing awareness and actively managing posture-related issues that elevate the likelihood of developing lower back pain symptoms.

The aim of this randomized controlled clinical trial was to compare the 2-year clinical performance of resin composite restorations placed at non-caries cervical lesions (NCCL) with one-step self-etch, total-etch, and selective enamel etch & self-etch adhesive techniques. Thirty-two patients received three resin composite restorations each at NCCLs (Tetric EvoCeram/Ivoclar/Vivadent), bonded with a total-etch adhesive agent (ExciTE F/Ivoclar/Vivadent) and a self-etch (AdheSE One F/Ivoclar/Vivadent) without and with selective enamel etching. All restorations were evaluated by two examiners at baseline, 6-, 12-, 18- and 24-months post-operation regarding retention, caries occurrence, marginal adaptation, and marginal staining. A logistic regression analysis with generalized estimating equations was used. After 2 years, the retention rate was 86,8% for total-etch, 92.26% for self-etch, and 93.63% for selective enamel etching & self-etch. No caries were detected during all the restorations. Concerning marginal adaptation, the clinically perfect restorations were 26.9% for the total-etch technique, 16% for self-etch, and 25,9% for selective enamel etch & self-etch. All three adhesive strategies provided restorations with no significant differences in the retention rate and the marginal adaptation, whereas the total etch yielded better performance for marginal staining. All the restorations were assessed as clinically acceptable after 2 years.

Aims: This study aims to evaluate the impact of family-centered empowerment on Jordanian adolescents with type 1 diabetes (T1DM), focusing on their HbA1c levels, self-efficacy, and quality of life (QOL). Background: Poor glycemic management in adolescents with type 1 diabetes increases complications. Improved control is linked to various variables, but few studies focus on Middle Eastern populations. Methods: An experimental study involved 68 adolescents with T1DM visiting Jordanian Royal Medical Services' clinics. Two sets of participants were created: control (n = 34) and intervention (n = 34). Data was collected through face-to-face interviews and medical records. Results: The study found significant differences in self-efficacy scores between the intervention and control groups, with the intervention group experiencing a significant decrease in HbA1c readings and a significant difference in QOL between pre-program and post-program phases. Discussion: Family empowerment can significantly improve the lives of Jordanian teenagers with type 1 diabetes. This strategy leads to improved glycemic management, increased self-efficacy, and improved quality of life. Future treatments and health policies should recognize and value the critical role families play in the care of this population. Conclusion: The study suggests that patients with T1DM should receive continuous care education sessions, including self-care training, to improve their health. Nurses should also incorporate these training into treatment plans and educational programs for adolescents to enhance their QOL.

Abstract: Fetal Alcohol Spectrum Disorder (FASD) is considered a lifelong disability that has been framed by neurobiological descriptions focused on the brain. These are important features but fail to tell the story of living with FASD. By surveying those with FASD, this work expands upon prior survey work which illustrated a multitude of early onset physiological issues occurring at rates much higher than typical of the general population. The current project, again using an anonymous survey methodology, seeks to open up other direct experiences to better understand the complexity of living with FASD. An anonymous online survey was used to gather data on advresity in childhood, schooling, employment, housing and finances, involvement with the criminal justice system as well as relationships and parenting. Results inform how supports can be enhanced and targeted with a goal of improving the quality of life. The survey was developed by adults living with FASD who have served as a long-standing advocacy and educational group influencing policy and practice in the field.

We explore 3D printing modules for self-assembling spacecraft and robots – structure, actuators, electrics. Self-assembly has long been viewed as a highly desirable capability for autonomous construction of large space structures. We review self-assembly in space which focusses on the self-assembly of modules that demonstrate the range of applications. However, self-assembly may be synergised with 3D printing to offer an automated capability from raw material to modules for assembling new spacecraft or habitats. One application of 3D printing is using space debris on-orbit as an in-situ resource - defunct spacecraft may be salvaged as raw material for in-situ construction on demand. The common features of all self-assembling modules are that the modules constitute a structure housing a computer-controlled actuator internally and a reversible latching mechanism externally. We have demonstrated a 3D printed DC electric motor in which the only components that were not 3D printed are the wire coils. We have married our 3D printed motor prototype as an actuated joint between two 3D printed trigon-type panels developed as part of a trigon self-assembling system concept. The trigon concept underlies a modular approach to self-assembling and self-deploying structures. The 3D printed motorised panel system demonstrates that the motor aspect and structural aspects of robotic self-assembling machines are amenable to 3D printing. This has implications for self-assembling systems into modular satellites as a solution to space debris.

With the development of artificial intelligence, the ability of capturing the background characteristics of hyperspectral imagery (HSI) is improved and promising performance in hyperspectral anomaly detection (HAD) tasks is yielded. However, existing methods proposed in recent years still suffer from certain limitations: 1) constraints are lacking in the deep feature learning process in terms of the issue for absence of prior background and anomaly information. 2) hyperspectral anomaly detectors with traditional self-supervised deep learning methods fail to ensure prioritized reconstruction of the background. 3) architectures of fully connected deep network in hyperspectral anomaly detectors lead to low utilization of spatial information and destruction for original spatial relationship of hyperspectral imagery, and disregard spectral correlation between adjacent pixels. 4) hypotheses or assumptions for background and anomaly distributions restrict the performance of many hyperspectral anomaly detectors because the distributions of background land covers are usually complex and not assumable in real-world hyperspectral imagery. With the consideration of above problems, in this paper, we propose a novel fully convolutional auto-encoder based on dual clustering and latent feature adversarial consistency (FCAE-DCAC) for HAD which is carried out in a self-supervised learning-based processing. Firstly, the density-based spatial clustering of applications with noise algorithm and connected component analysis are utilized for successive spectral and spatial clustering to obtain more precise prior background and anomaly information, which facilitates the separation between background and anomaly samples during the training of our method. Subsequently, a novel fully convolutional auto-encoder (FCAE) integrated with spatial-spectral joint attention (SSJA) is proposed to enhance the utilization of spatial information and augment feature expression. In addition, a latent feature adversarial consistency network is proposed to achieve pure background reconstruction with the ability of learning actual background distribution in hyperspectral imagery. Finally, a triplet loss is introduced to enhance the separability between background and anomaly, and the reconstruction residual serves as the anomaly detection result. We evaluate the proposed method on seven groups of real-world hyperspectral datasets, and the experimental results confirmed the effectiveness and superior performance of the proposed method versus nine state-of-the-art methods.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

In an outstanding article published in 2008, Suzuki obtained a nice generalization of the Banach contraction principle from which derived a characterization of metric completeness. Although Suzuki’s theorem has been successfully generalized and extended in several directions and contexts, we here show by means of a simple example that the problem of achieving, in an obvious way, its full extension to the framework of w-distances does not have an emphatic response. Motivated by this fact we introduce the concept of presymmetric w-distance on metric spaces, we give some properties and examples of this new structure and show that it provides a reasonable setting to obtain a real and hardly forced w-distance generalization of Suzuki’s theorem. This is realized in our main result, which is a fixed point theorem that involves presymmetric w-distances and certain contractions of Suzuki-type. We also discuss the relationship between our main result and the well-known w-distance full generalization of the Banach contraction principle, due to Suzuki and Takahashi. Connected to this approach we prove another fixed point result that compare with our main result through some examples. Finally, we state a characterization of metric completeness by using our fixed point results.

In today’s competitive landscape, achieving customer-centricity is paramount for the sustainable growth and success of organisations. This research is dedicated to understanding customer preferences in the context of the Internet of Things (IoT) and employs a two-part modeling ap-proach tailored in this digital era. In the first phase, we leverage the power of the Self-Organizing Map (SOM) algorithm to segment IoT customers based on their connected device usage patterns. This segmentation approach reveals three distinct customer clusters, with the second cluster demonstrating the highest propensity for IoT device adoption and usage. In the second phase, we introduce a robust Decision Tree methodology designed to prioritize various factors influencing customer satisfaction in the IoT ecosystem. We employ the Classification and Regression Tree (CART) technique to analyze 17 key questions that assess the significance of factors impacting IoT device purchase decisions. By aligning these factors with the identified IoT customer clusters, we gain profound insights into customer behaviour and preferences in the rapidly evolving world of connected devices. This comprehensive analysis delves into the factors contributing to customer retention in the IoT space, with a strong emphasis on crafting logical marketing strategies, en-hancing customer satisfaction, and fostering customer loyalty in the digital realm. Our research methodology involves surveys and questionnaires distributed to 207 IoT users, categorizing them into three distinct IoT customer groups. Leveraging analytical statistical methods, regression analysis, and IoT-specific tools and software, this study rigorously evaluate the factors influencing IoT device purchases. Importantly, this approach not only effectively clusters the IoT Customer Relationship Management (IoT-CRM) dataset but also provides valuable visualizations that are essential for understanding the complex dynamics of the IoT customer landscape. Our findings underscore the critical role of logical marketing strategies, customer satisfaction, and customer loyalty in enhancing customer retention in the IoT era. This research makes a significant contri-bution to businesses seeking to optimize their IoT -CRM strategies and capitalize on the oppor-tunities presented by the IoT ecosystem.