Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

Intracellular potassium concentrations, [K+], are high in all types of living cells, but the origins of this K+ are unknown. The simplest hypothesis is that life emerged in an environment that was high in K+. One such environment is the spaces between the sheets of the clay mineral, mica. The best mica for life’s origins is the black mica, biotite, because it has a high content of Mg++ and it has iron in various oxidation states. Life also has many of the characteristics of the environment between mica sheets, giving further support for the possibility that mica was the substrate on and within which life emerged.

An area has been designated for demonstrating the utility of marine hydrokinetic turbines in Minas Passage, Bay of Fundy. Marine renewable energy may be useful for the transition from carbon-based energy sources but there is concern for the safety of fish that might encounter turbines. Acoustic receivers that detect signals from acoustically tagged fish that pass through the tidal demonstration area and detection efficiency of tag signals might be used to estimate the likelihood of fish encountering marine hydrokinetic turbines. The method requires that tagged fish passing through the development area will be reliably detected by a receiver array. The present research tests the reliability with which passing tags are detected by suspending tags beneath GPS-tracked drifters. Drifters carrying high residency Innovasea tags that transmitted every 2 seconds were usually detected by the receiver array even in fast currents during spring tides but pulse position modulation tags were inadequate. Sometimes very few high residency tag signals were detected when fast tidal currents swept a drifter through the receiver array, so increasing the transmission interval degrades performance at the tidal energy development area. High residency tags suspended close to the sea surface were slightly less likely to be detected if they passed by during calm conditions. Previously measured detection efficiencies were found to slightly overestimate the chances of a high residency tag carried by a drifter being detected as it passed by a receiver. This works elucidates the effectiveness with which acoustically tagged fish are detected in fast, highly turbulent tidal currents and informs the application of detection efficiency measurements to calculate the probability that fish encounter a marine hydrokinetic turbine.

Here, using the theory of electrical-quantum modelling of the neutron and proton as a three-phase alternating current electrical generator, we will analyse the proton decay and the inverse neutron decay and determine the following subatomic particles, Dproton, Protoniu, Dneutron and Neutroniumd.

Background and Objective: Segmentation of the femur in Dual Energy X-ray (DXA) images poses challenges due to reduced contrast, noise, bone shape variations, and inconsistent X-ray beam penetration. In this study, we investigate the relationship between noise and certain deep learning (DL) techniques for semantic segmentation of the femur to enhance segmentation and bone mineral density (BMD) accuracy by incorporating noise reduction methods into DL models. Methods: Convolutional neural network (CNN) based models were employed to segment femurs in DXA images and evaluate the effects of noise reduction filters on segmentation accuracy and its effect on BMD calculation. Various noise reduction techniques were integrated into DL-based models to enhance image quality before training. We assessed the performance of the fully convolutional neural network (FCNN) in comparison to noise reduction algorithms and manual segmentation methods. Results: Our study demonstrated that FCNN outperformed noise reduction algorithms in enhancing segmentation accuracy and enabling precise calculation of BMD. The FCNN-based segmentation approach achieved a segmentation accuracy of 98.84% and a correlation coefficient of 0.9928 for BMD measurements, indicating its effectiveness in the clinical diagnosis of osteoporosis. Conclusions: In conclusion, integrating noise reduction techniques into DL-based models significantly improves femur segmentation accuracy in DXA images. The FCNN model, in particular, shows promising results in enhancing BMD calculation and clinical diagnosis of osteoporosis. These findings highlight the potential of DL techniques in addressing segmentation challenges and improving diagnostic accuracy in medical imaging.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

Dietary assessment methods recognized as appropriate for the general population are usually applied in a similar manner to athletes, despite knowledge that sport-specific factors can complicate assessment and impact accuracy in unique ways. As dietary assessment methods are used extensively within the field of sports nutrition, there is concern the validity of methodologies have not undergone more rigorous evaluation in this unique population sub-group. The purpose was to systematically review studies comparing two or more methods of dietary assessment, including dietary intake measured against biomarkers or reference measures of energy expenditure, in athletes. Six electronic databases were searched for English-language, full-text articles published from January 1980 until June 2016. The search strategy combined the following keywords: diet, nutrition assessment, athlete and validity; where the following outcomes are reported but not limited to: energy intake, macro and/or micronutrient intake, food intake, nutritional adequacy, diet quality, or nutritional status. Meta-analysis was performed on studies with sufficient methodological similarity, with between-group standardized mean differences (or effect size) and 95 % confidence intervals (CI) calculated. Of the 1624 studies identified, 18 were eligible for inclusion. Studies comparing self-reported energy intake (EI) to energy expenditure assessed via doubly labelled water were grouped for comparison (n=11) and demonstrated mean EI was under-estimated by 19 % (- 2793 ± 1134 kJ/d). Meta-analysis revealed a large pooled effect size of - 1.006 (95% CI: -1.3 to -0.7; p<0.001). The remaining studies (n=7) compared a new dietary tool or instrument to a reference method(s) (e.g. food record, 24-h dietary recall, biomarker) as part of a validation study. This systematic review revealed there are limited robust studies evaluating dietary assessment methods in athletes. Existing literature demonstrates substantial variability between methods, with under and misreporting of intake frequently observed. There is a clear need for careful validation of dietary assessment methods, including emerging technical innovations, among athlete populations.

From June 18 to 19, 2013, the Ésera river in the Pyrenees, Northern Spain, caused widespread damage due to flooding as a result of torrential rains and sustained snowmelt. We estimate the contribution of snow melt to total discharge applying a snow energy balance to the catchment. Precipitation is derived from sparse local measurements and the WRF-ARW model over three nested domains, down to a grid cell size of 2 km. Temperature profiles, precipitation and precipitation gradient are well simulated, although with a possible displacement regarding the observations. Snowpack melting was correctly reproduced and verified in three instrumented sites, and according to satellite images. We found that the hydrological simulations agree well with measured discharge. Snowmelt represented 33% of total runoff during the main flood event and 23% at peak flow. The snow energy balance model indicates that most of the energy for snow melt during the day of maximum precipitation came from turbulent fluxes. This approach forecast correctly peak flow and discharge during normal conditions at least 24h in advance and could give an early warning of the extreme event 2.5 days before.

Deep learning has been applied in many areas that have had a significant impact on applications that improves real-life challenges. The success of deep learning in a wide range of areas is due in part to the use of activation functions, which are particularly effective at solving non-linear problems. Activation functions are a key focus for researchers in artificial intelligence who aim to improve the performance of neural networks. This article provides a comprehensive explanation and comparison of different activation functions, with a focus on the arc tangent and its variations specifically. The paper presents experimental results that show that variations of the arc tangent using irrational numbers such as pi, the golden ratio, and Euler’s number, as well as a self-arctan function, produce promising results. Since we experimented with promising activation functions on two different problems, and datasets, we reached a result that different irrationals work well for different problems. In other words, arctan ϕ gives the best results mostly for multiclass classification and arctan e gives the best results for time series prediction problems. The paper focuses on a multi-class classification problem applied to the Reuters Newswire dataset and a time-series prediction problem on Türkiye energy trade value to show the impacts of activation functions.

After an introductory reminder of safety concerns pertaining to early rechargeable battery technologies, this review discusses current understandings and challenges of sodium-ion batteries. Sodium-ion technology is now being marketed by industrial promoters who are advocating its workable capacity, use of readily accessible and cheaper key cell components. Often claimed to be safer than lithium-ion cells, currently only limited scientific-sound safety assessment of sodium-ion cells has been performed. However, the predicted sodium-ion development roadmap reveals that significant variants of sodium-ion batteries will potentially enter the market in the near future. With recent experiences of lithium-ion battery failures, sodium-ion battery safety management will constitute a key aspect of successful market penetration. As such this review discusses the safety issues of sodium-ion batteries presenting a twofold innovative perspective: i) in terms of comparison with the parent lithium-ion technology making use of the same working principle and similar flammable non-aqueous solvent basis and ii) anticipating the arrival of innovative sub-chemistries at least partially inspired from successive generations of lithium-ion cells. The authors do hope that the analysis provided will assist the concerned stakeholders in the quest for safe marketing of sodium-ion batteries.

Dimethylformamide (DMF), a polar solvent, is commonly used for preparing graphene/epoxy nanocomposites. While commonly previous research has predominantly highlighted the improvement in physio-mechanical properties of these nanocomposites, the effect of DMF on processing and its direct influence on the final characteristics of MXene/epoxy nanocomposites have not been investigated.This unexplored link between DMF dosage, MXene concentrations, and the final composite properties presents an exciting direction for future research. In this study, a fixed dosage of DMF was used with varying MXene concentrations to fabricate the nanocomposites. To assess the reliability of DMF dosage on the characteristics of the fabricated nanocomposites, various evaluation techniques were employed, including dispersion evaluation, mechanical tests, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), electromagnetic interference (EMI) shielding, and surface roughness measurements. The research outcomes revealed that as MXene concentration increased, the characteristics of the MXene/epoxy nanocomposites, improved across the board, indicating their potential for use in energy storage applications.

This study assesses the impact of militarization, industrialization, technological innovation, and energy consumption on CO2 emissions in NATO countries, divided into "traditional" (Group 1) and "new member" states (Group 2), using data from 1985 to 2019. It identifies heterogeneity in effects and dependencies between the groups. Employing Pedroni and Kao panel cointegration tests, a long-term equilibrium relationship among the variables is confirmed. The analysis, using panel ARDL and GMM methods, reveals distinct outcomes for each group. In Group 1, military spending and energy consumption significantly increase CO2 emissions, while industrialization and technological innovation reduce them. Conversely, in Group 2, technological innovation and energy consumption raise emissions, whereas military spending and industrialization decrease them. The findings suggest Group 1 should strategize military expenditure and energy consumption to cut emissions, whereas Group 2 should focus on eco-friendly technology and efficient energy use to achieve environmental sustainability.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

We study the coupling of two topologcal subsystems in distinct topological states, and show that it leads to a precursor behavior of the topological phase transition in the overall system. This behavior is solely determined by the symmetry classes of the subsystem Hamiltonians and coupling terms, and is marked by the persistent existence of subgap states within the bulk energy gap. By investigating the critical current of Josephson junctions involving topological superconductors, we also illustrate that such subgap states play crucial roles in physical properties of nanoscale devices or materials.

As the global demand for renewable energy continues to rise, biogas technology has emerged as a promising solution for sustainable energy generation. This review article presents the advantages of biogas technologies and extensively discusses the main principles of biogas production in the methane fermentation process. In this respect, the main parameters of the process, which require monitoring and are at the same time decisive for its course and efficiency are described, the principles of substrate selection are discussed and the necessity and advantages of the use of organic waste according to the model of a circular economy and the concept of sustainable development, are indicated. The part on biogas production is summarised with an explanation of the necessity to treat and purify biogas, taking into account the share of methane extracted. A special place in this paper is devoted to the design, construction, functioning and operation of biogas plants, based on both scientific and practical aspects. In conclusion of this chapter, the economic aspects and profitability of operating biogas plants are discussed, taking into account, in a theoretical balance sheet – in addition to investment and operating costs and the availability and cost of raw materials – the possibilities of producing and using electricity and heat, as well as environmental and social benefits. The article concludes with a discussion of opportunities and barriers to the development of biogas plants, pointing to: financial issues, access to feedstock, political regulations, public awareness and the geopolitical situation as key factors issues related to biogas plants – in different regions of the world.

High-performance insulation and airtight building envelopes are the two most important factors to optimize the building energy efficiency and thermal performance. However, thermal performance of building envelopes can be significantly affected by thermal bridging. Thermal bridges can take place at different locations of the building envelope, causing added transmission losses, increasing heat flow, lower inner surface temperatures. Thermal bridges are regarded in all national regulations for new buildings of all states of European Union (EU) but there are no specifications assessing balconies to wall junctions and the impact on the building thermal performance is not well regulated. In this paper, balcony to wall thermal bridge assessment using infrared thermography is highlighted. The originality is that, infrared thermography, has been applied to a real living latest building in the north east of France showing that there is noncompliance in the national regulations as some exigencies are not met. Thermography of thermal break windows and window doors has also revealed air leakage. The goal, is to illustrate that thermal imaging is a means of quality assurance to new building specifications and should include a clause specifying quality assurance procedure for balconies junction in national building regulations for all states if the EU.

Portugal, in line with the European Union, is aiming for carbon neutrality by 2050 (Net 1 Zero), which implies a transition to sustainable energy sources. Climate change is all too evident, extreme weather periods are occurring in a cyclical manner, with greater brevity to such an extent that the grid operator must deal with production scenarios where it can no longer rely on hydroelectric production given the recurring drought situation. This situation increases dependence on thermal production using natural gas and imports. This has significant economic implications. Portugal has exploited its onshore wind potential, reaching an installed capacity of 5.671 MW by 2022. However, the expansion of onshore wind energy is limited to reinforcing existing infrastructure. To overcome these challenges, it is necessary to expand the exploitation of offshore wind potential that is already underway. This article proposes the location of offshore wind production platforms along the Portuguese coast. This allows for an analysis of offshore production and its optimization according to the minimum cost per MWh in the face of extreme scenarios, i.e., in periods of extreme drought where hydroelectric production capacity is practically non-existent. The model is fed by using market price indications and the amount of energy needed for the following day. Using forecast data, the model adapts offshore wind production for the following day according to the minimization of the average market price. The results of the simulations allow us to conclude that despite the high cost of offshore technology (in deep waters), in extreme climate scenarios, it enables cost reduction and a clear decrease in imports.

This paper presents a parametric study of the multistorey hydro-powered pump, known as "Bunyip," which has demonstrated significant potential in contributing to rural regions. The study aims to understand the underlying physics of the system and enhance its hydraulic performance. A transient three-dimensional model using the commercial Computational Fluid Dynamics (CFD) tool Ansys-Fluent is utilized to gain insights into the fundamental flow mechanics, operational efficiency, standard capacity, and relative delivery. The investigation involves an initial assessment of performance for three Bunyip devices based on manufacturing data. Parametric analysis is conducted, and a parametric dataset is generated through meticulous application and numerical modelling. The CFD results are validated against experimental data. Three design configurations are considered, and 58 sets of varied input parameters are examined. The best design configuration is evaluated against five cases of conventional hydro-power pump systems. The results indicate that a smaller diameter of the pressure chamber and a higher supply head lead to higher pressure, achieving a target head of 3 m with 15% efficiency and a flowrate of 11.82 l/min.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.

Daniel Yergin’s “The New Map: Energy, Climate, and the Clash of Nations” is a remarkable and groundbreaking work that addresses the ever-changing global energy landscape and its profound geopolitical implications. In this modest book review, we aim to offer a fresh perspective by re-examining the core issues from the standpoint of political geography. The aim of this article is twofold: to enrich the existing literature on political geography and to provide valuable insights to students of geography to broaden their knowledge in this field.

In this work, we compiled our research on lanthanide-based luminescent materials, prepared down-shifter layers, and studied their effect on photovoltaic (PV) mini-modules. The compounds we have prepared (C1-C17), with formulas [Eu2(phen)2(bz)6] (C1), [Eu2(bphen)2(bz)6] (C2), [Eu(tta)3bphen] (C3), [Eu(bta)3pyz-phen] (C4), [Eu(tta)3pyz-phen] (C5), [Eu(bta)3me-phen] (C6), [Er(bta)3me-phen] (C7), [Yb(bta)3me-phen] (C8), [Gd(bta)3me-phen] (C9), [Yb(bta)3pyz-phen] (C10), [Er(tta)3pyz-phen] (C11), [Eu2(bz)4(tta)2(phen)2] (C12), [Gd2(bz)4(tta)2(phen)2] (C13), [EuTb(bz)4(tta)2(phen)2] (C14), [EuGd(bz)4(tta)2(phen)2] (C15), [Eu1.2Gd0.8(bz)4(tta)2(phen)2] (C16) and [Eu1.6Gd0.4(bz)4(tta)2(phen)2] (C17), can be grouped into three families based on their composition: Series C1–6 were synthesized using Eu3+ ions and phenanthroline derivatives as the neutral ligands, and fluorinated β-diketonates as the anionic ligands. Complexes C7–11 were prepared with ligands similar to those of compounds C1–6 but were synthesized with Er3+, Yb3+, or Gd3+ ions. Series C12–17 exhibit the general formula [M1M2(bz)4(tta)2(phen)2], where M1 and M2 can be Eu3+, Gd3+, or Tb3+ ions, and the ligands are benzoate (bz–), 2-thenoyltrifluoroacetone (tta–) and 1,10–phenanthroline (phen). All compounds were characterized using X-ray techniques, and their photoluminescent properties were studied. We then examined their impact on the EQE (External Quantum Efficiency) of PV mini-modules and their durability in a climate chamber when embedded in PMMA and EVA films. This review emphasizes the methodology employed and the key findings, including enhanced mini-module efficiency. Additionally, we present promising results on the application of compound C6 in a bifacial solar cell.

We derive a quantum speed limit for unitary evolution for the case of mixed quantum states using the stronger uncertainty relation for mixed quantum states. This bound can be optimized over different choices of Hermitian operators for a better bound. We illustrate this with some examples and show its better performance with respect to three existing bounds for mixed quantum states.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

Much evidence suggests a correlation between degeneration and mitochondrial impairment. Typical cases of degeneration can also be observed in physiological phenomena (aging) as well as in neurological neurodegenerative diseases and cancer. All these pathologies have as a common denominator the dyshomeostasis of mitochondrial bioenergy. Even neurodegenerative diseases show a bioenergetics imbalance in their pathogenesis or progression. Huntington's chorea and Parkinson's disease are both neurodegenerative diseases, but while Huntington's disease is a genetic, and progressive disease with early manifestation and severe penetrance, Parkinson's disease is a pathology with a multifactorial aspect. Indeed, there are different types of Parkinson/Parkinsonism. Many forms are early onset diseases linked to gene mutation, others can appear in young adults and senescent only post-injury, and a final group is idiopathic. Huntington's was defined as a hyperkinetic disorder, while Parkinson's is a hypokinetic disorder; but in the middle, there are a lot of similarities as well as neuronal excitability, the loss of striatal function, psychiatric comorbidity, etc. In the review, we would embrace the theories that both diseases start and develop in light of mitochondrial dysfunction. These dysfunctions act on energy metabolism and reduce the vitality of neurons in many different brain areas.

The digital era offers many opportunities to the wind energy industry and research community. Digitalisation is one of the key drivers for reducing costs and risks over the whole wind energy project life cycle. One of the largest challenges in successfully implementing digitalisation is the lack of data sharing and collaboration between organisations in the sector. In order to overcome this challenge, a new collaboration method called WeDoWind was developed in recent work. The main innovation of this method is the way it creates tangible incentives to motivate and empower different types of people from all over the world to actually share data and knowledge in practice. In this present paper, the challenges related to comparing and evaluating different SCADA data based wind turbine fault detection models are investigated by carrying out a new case study, the "WinJi Gearbox Fault Detection Challenge", based on the WeDoWind Method. Six new solutions were submitted to the challenge, and a comparison and evaluation of the results show that, in general, some of the approaches (Particle Swarm Optimisation algorithm for constructing health indicators, performance monitoring using Deep Neural Networks, Combined Ward Hierarchical Clustering and Novelty Detection with Local Outlier Factor and Time-to-failure prediction using Random Forest Regression) appear to have a high potential to reach the goals of the Challenge. However, there are a number of concrete things that would have to have been done by the Challenge providers and the Challenge moderators in order to ensure success. This includes enabling access to more details of the different failure types, access to multiple data sets from more wind turbines experiencing gearbox failure, provision of a model or rule relating fault detection times or a remaining useful lifetime to the estimated costs for repairs, replacements and inspections, provision of a clear strategy for training and test periods in advance, as well as provision of a pre-defined template or requirements for the results. These learning outcomes are used directly to define a set of best practice data sharing guidelines for wind turbine fault detection model evaluation. They can be used by the sector in order to improve model evaluation and data sharing in the future.

Much evidence suggests a correlation between degeneration and mitochondrial impairment. Typical cases of degeneration can also be observed in physiological phenomena (aging) as well as in neurological neurodegenerative diseases and cancer. All these pathologies have as a common denominator the dyshomeostasis of mitochondrial bioenergy. Even neurodegenerative diseases show a bioenergetics imbalance in their pathogenesis or progression. Huntington's chorea and Parkinson's disease are both neurodegenerative diseases, but while Huntington's disease is a genetic, and progressive disease with early manifestation and severe penetrance, Parkinson's disease is a pathology with a multifactorial aspect. Indeed, there are different types of Parkinson/Parkinsonism. Many forms are early onset diseases linked to gene mutation, others can appear in young adults and senescent only post-injury, and a final group is idiopathic. Huntington's was defined as a hyperkinetic disorder, while Parkinson's is a hypokinetic disorder; but in the middle, there are a lot of similarities as well as neuronal excitability, the loss of striatal function, psychiatric comorbidity, etc. In the review, we would embrace the theories that both diseases start and develop in light of mitochondrial dysfunction. These dysfunctions act on energy metabolism and reduce the vitality of neurons in many different brain areas.

Luminophores featuring thermally activated delayed fluorescence (TADF luminophores) are the workhorse of the third- and fourth-generation OLEDs. While these compounds had usually been used as dopants embedded in the host, non-doped TADF OLEDs have recently shown significant progress as well reaching the performance comparable to the host-dopant ones. For efficient operation of the non-doped OLEDs, charge transport in neat films and single crystals of TADF luminophores is important; however, this issue was nearly unexplored theoretically. In the current study, we calculated charge mobilities in four TADF single crystals, which have different molecular packing motifs. Specifically, in one of them both donor and acceptor moieties form uniform π-stacks, while in the others donors (acceptors) show alternating lateral shifts along the stacks; the difference in molecular packing results in the difference of transfer integral between the molecules. Reorganization energies differ as well up to four times for the studied crystals. As a result, charge mobilities vary from 0.001 to ~0.3 cm2/(V∙s), the largest being predicted for the crystal of the luminophore consisting of rigid donor and acceptor. We anticipate that the results obtained can be useful for the design of TADF luminophores for non-doped OLEDs, OLETs and other organic light-emitting devices.

Global temperature rise due to hydrocarbon gases emission that are produced by generating the electrical power has a great attention by the researchers to reduce it till zero emission is successfully achieved. Sustainable energy source such as solar energy, wind, hydro-energy and sea wave energy are focal areas to replace the fossil fuel by clean energy. In this article, daylight is used to minimize the power consumption that required for indoor lighting using electric roller blind. Smart controller is designed to adjust the position of the roller blind stepper motor, and hence, adjust the roller blind opening, based on the preset light intensity, to achieve precise utilization of daylight inside the room. If the desired Lux is not achieved for any reason, the smart controller adjusts the LED circuit current to boost the light intensity to achieve precisely the desired Lux. Comprehensive test cases using MATLAB-Simulink is carried out to verify the performance of the proposed smart controller. Techno-economic analysis is introduced to evaluate the benefits of installing the controller. Summary and recommendation are given at the end.

Estimating evapotranspiration at field scale is a major component of sustainable water management. Due to the difficulty to assess some major unknowns of the water cycle at that scale, including irrigation amounts, evapotranspiration is often computed as the residual of the instantaneous surface energy budget. One of the Surface Energy Bal-ance components with the largest uncertainties in their quantification over bare soils and sparse vegetation areas is the ground heat flux (G). Over the last decades, the es-timation of G with RS data has been mainly achieved with empirical equations, on the basis of the G and net radiation (Rn) ratio, G/Rn. G/Rn empirical equations generally require vegetation data (Type I empirical equations), in combination with surface tem-perature (Ts) and albedo (Type II empirical equations). In this article we aim to evalu-ate the estimation of G with RS. For the first time, we compare eight G/Rn empirical equations against two types of machine learning (ML) methods: an ensemble ML type, the Random Forest (RF), and the Neural Networks (NN). The comparison of each method is evaluated over dense dataset, including a wide range of climate and land covers, with data of Eddy-Covariance towers extended along the mid-latitude area that encompass the European and African continent. Our results have shown evidence that the driver of G in bare soils and sparse vegetation areas (Fraction of Vegetation, Fv <= 0.25) is Ts, instead of vegetation greenness indexes. On the other hand, the estimation of G with Rn, Ts or Fv decreases at dense vegetation areas (Fv >= 0.50). There are not significant differences between the most accurate type I and II empirical equations. For bare soils and sparse vegetation areas the empirical equation that better estimates G is E8, which combines the Leaf Area Index (LAI) and Ts. In dense vegetation areas (Fv >= 0.25), an exponential empirical equation based on Fv (E4), shows the best performance. However, ML better estimates G than the empirical equations, independently of the Fv ranges. A RF model with Rn, LAI and Ts as predictor variables shows the best accuracy and performance metrics, outperforming the NN model.

Each year in March, adherents of the Bahá’í faith abstain from eating and drinking from sunrise to sunset for 19 days. Thus, Bahá’í fasting (BF) can be considered as a form of daytime dry fasting. We tested if BF decreases energy expenditure after a meal and improves anthropometric measures, and systemic and tissue-level metabolic parameters. This was a self-controlled cohort study with 11 healthy men. We measured anthropometric parameters, metabolic markers in venous blood, and pre- and postprandial energy metabolism at systemic (indirect calorimetry) and tissue (adipose tissue and skeletal muscle microdialysis) level, both before and during BF. During BF, we found reduced body weight, body mass index, body fat and blood glucose. Postprandial increase in energy expenditure was lower, diet-induced thermogenesis tended to be lower. In adipose tissue, perfusion, glucose supply and lipolysis were increased. In skeletal muscle, tissue perfusion did not change. Glucose supply and lipolysis were decreased. Glucose oxidation was increased, indicating an improved insulin sensitivity. BF may be a promising approach to losing weight and improving metabolism and health. However, outside the context of religiously-motivated fasting, skipping a meal rather in the evening (dinner cancelling) might be recommended, as metabolism appears to be reduced in the evening.

Driven by the proliferation of DC energy sources and DC end-use devices (e.g., photovoltaics, battery storage, solid-state lighting, and consumer electronics), DC power distribution in buildings has recently emerged as a path to improved efficiency, resilience, and cost savings in the transitioning building sector. Despite these important benefits, there are several technological and market barriers impeding the development of DC distribution, which have kept this technology at the demonstration phase. This paper identifies specific end-use cases for which DC distribution in buildings is viable today. We evaluate their technology and market readiness, as well as their efficiency, cost, and resiliency benefits while addressing implementation barriers. The paper starts with a technology review, followed by a comprehensive market assessment, in which we analyze DC distribution field deployments and their end-use characteristics. We also conduct a survey of DC power and building professionals through on-site visits and phone interviews and summarize lessons learned and recommendations. In addition, the paper includes a novel efficiency analysis, in which we quantify energy savings from DC distribution for different end-use categories. Based on our findings, we present specific adoption pathways for DC in buildings that can be implemented today, and for each pathway we identify challenges and offer recommendations for the research and building community.

Hubble expansion may be considered as a velocity per photon travel time rather than as velocity or redshift per distance. Dimensionally, this is an acceleration and will have an associated curvature of space under general relativity. This paper explores this theoretical curvature as an extension to the spacetime manifold of general relativity, generating a modified solution with three additional non-zero Christoffel symbols, and a reformulated Ricci tensor and curvature. The observational consequences of this reformulation were compared with the ΛCDM model for luminosity distance using the extensive type Ia supernovae (SNe Ia) data with redshift corrected to the CMB, and for angular diameter distance with the recent baryonic acoustic oscillation (BAO) data. For the SNe Ia data, the modified GR and ΛCDM models differed by −0.15+0.11μB mag. over zcmb=0.01−1.3, with overall weighted RMS errors of ±0.136μB mag for modified GR and ±0.151μB mag for ΛCDM espectively. The BAO measures spanned a range z=0.106−2.36, with weighted RMS errors of ±0.034 Mpc with H0=67.6±0.25 for the modified GR model, and ±0.085 Mpc with H0=70.0±0.25 for the ΛCDM model. The derived GR metric for this new solution describes both the SNe Ia and the BAO observations with comparable accuracy to ΛCDM without requiring the inclusion of dark matter or w’-corrected dark energy.

The high-resolution bistatic lidar developed at the Physikalisch-Technische Bundesanstalt (PTB) aims to overcome the limitations of conventional monostatic lidar technology which is widely used for wind velocity measurements in wind energy and meteorology applications. Due to the large measurement volume of a combined optical transmitter and receiver tilting in multiple directions, monostatic lidar generally has poor spatial and temporal resolution. It also exhibits large measurement uncertainty when operated in inhomogeneous flow, for instance, over complex terrain. In contrast, PTB’s bistatic lidar uses three dedicated receivers arranged around a central transmitter, resulting in an exceptionally small measurement volume. The coherent detection and modulation schemes used allow the detection of backscattered, Doppler shifted light down to the scale of single aerosols, realising the simultaneous measurement of all three wind velocity components. This paper outlines design details and the theory of operation of PTB’s bistatic lidar and provides an overview of selected comparative measurements. The results of these measurements have shown that the measurement uncertainty of PTB’s bistatic lidar is well within the measurement uncertainty of traditional cup anemometers, while being fully independent of its site and traceable to the SI units. This allows its use as a transfer standard for the calibration of other remote sensing devices. Overall, PTB’s bistatic lidar shows great potential to universally improve the capability and accuracy of wind velocity measurements, such as for the investigation of highly dynamic flow processes upstream and in the wake of wind turbines.

Smart air filters are beneficial to provide highly efficient particle removal, treat multiple contaminants simultaneously and conserve energy during air filtration processes. Herein, a type of self-supporting smart air filter (SSSAF) was fabricated by sandwiching the VOC-responsive PZT/PVDF electrospun membrane with two metal mesh electrodes. Besides the high filtration efficiency for sub-micron particles, the SSSAF showed good responses to pressure drop in the range of 0 to 500 Pa via the electroactivity of PZT/PVDF membrane. In addition, the SSSAF achieved VOC sensing function via the swelling properties of PZT/PVDF membrane in organic vapors, demonstrated by its signal to 50 to 200 ppm ethanol gases. The SSSAF based nanogenerator was employed to harvest wind energy, which was further applied to inhibit bacterial growth without the need of additional power input. The results provide new insight into development of all-in-one smart air filters.

: The significance of heating load (HL) accurate approximation is the primary motivation of this research to distinguish the most efficient predictive model among several neural-metaheuristic models. The proposed models are through synthesizing multi-layer perceptron network (MLP) with ant lion optimization (ALO), biogeography-based optimization (BBO), dragonfly algorithm (DA), evolutionary strategy (ES), invasive weed optimization (IWO), and league champion optimization (LCA) hybrid algorithms. Each ensemble is optimized in terms of the operating population. Accordingly, the ALO-MLP, BBO-MLP, DA-MLP, ES-MLP, IWO-MLP, and LCA-MLP presented their best performance for population sizes of 350, 400, 200, 500, 50, and 300, respectively. The comparison was carried out by implementing a ranking system. Based on the obtained overall scores (OSs), the BBO (OS = 36) featured as the most capable optimization technique, followed by ALO (OS = 27) and ES (OS = 20). Due to the efficient performance of these algorithms, the corresponding MLPs can be promising substitutes for traditional methods used for HL analysis.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

A run-of-the-mill remote sensor arrange comprises numerous vitality compelled sensor hubs that are arbitrarily sent is the sensor field. Vitality is one of the most significant parts of planning an information dispersal convention for applications, for example, war zone checking, living space observing, and so on. We present EGDD, an Energy-effective Grid-based Data Dissemination plot for arbitrarily conveyed remote sensor systems. The proposed conspire is vitality effective for dealing with both sink and source portability. EGDD depends on a virtual framework-based foundation for information scattering from various versatile sources to different portable sinks. The virtual lattice of square size is built by the main source showing up in the sensor field dependent on the remaining vitality of the sensor hubs. Moreover, we proposed an askew sending calculation for inquiry and information sending which guarantees that just a single spread hub advances the question and information at once. In EGDD, substitute scattering hubs are chosen ahead of time during the lattice development procedure and the least limit vitality level is characterized for spread hubs. When the vitality of a dispersal hub arrives at the base edge esteem, it is supplanted by another spread hub. The reenactment results show that the proposed EGDD conspire is more vitality proficient when contrasted with other information scattering conventions.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

We have used the varying physical constant approach to resolve the flatness problem in cosmology. Friedmann equations are modified to include variability of speed of light, gravitational constant, cosmological constant and the curvature constant. The continuity equation obtained with such modifications includes scale factor dependent cosmological term as well as the curvature term along with the standard energy-momentum term. The result is that as the scale factor tends to zero (i.e. as the big-bang is approached) the universe becomes strongly curved rather than flatter and flatter in the standard cosmology. We have used the supernovae 1a redshift versus distance modulus data to determine the curvature variation parameter of the new model, which yields a better fit to the data than the standard ΛCDM model. The universe is found to be open type with radius of curvature R_c = 1.64 (1+z)^-3.3 c₀/H₀, where z is the redshift, c₀ is the current speed of light and H₀ is the Hubble constant.

The purpose of this paper is to find a quantum formulation of entropic gravity, incorporating the bijective theory. In a first part, we will describe the basis of the bijective theory. In a second part, we will incorporate the stress energy quantum tensor defined in the linear approximation of the Einstein’s equation in its quantum version to entropy. In the third part, we will integrate the bijective theory with the newly created relativistic quantum entropy. This will lead us four part where we will formalize quantum entropic gravity.

In this article it is shown how Milgrom’s acceleration constant is related with the Ω_Λ, Ω_m and Ω_B values of the matter distribution within observable universe as defined in the Standard Model of Cosmology, established by the Planck Collaboration Group. The result is a two-parameter model for the observable universe. The two parameters are the age of the universe and Milgrom’s acceleration constant. It is shown that these are sufficient to calculate the amounts of matter and dark energy in the universe, as well as the contributions of dark matter and baryonic matter in the matter part. The numerical results are in agreement with those of the Lamda-CDM model.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

The increased focus on sustainability in response to climate changes has given rise to many new initiatives to meet the rise in building load demand. The concept of distributed energy resources (DER) and optimal control of supply to meet power demands in buildings have resulted in growing interest to adopt microgrids for a precinct or a university campus. In this paper, a model for an actual physical microgrid has been constructed in OPAL-RT for real-time simulation studies. The load demands for SIT@NYP campus and its weather data are collected to serve as input to run on the digital twin model of DERs of the microgrid. The dynamic response of the microgrid model in response to fluctuations in power generation due to intermittent solar PV generation and load demands are examined via real-time simulation studies and compared with the response of the physical assets. It is observed that the simulation results match closely to the performance of the actual physical asset. As such, the developed microgrid model offers plug-and-play capability which will allow power providers to better plan for on-site deployment of renewable energy sources and energy storage to match the expected building energy demand.

Diamond-like carbon (DLC) films have a promising tribological application in green precision manufacturing, but their toughness represents a serious issue in the way of their application perspective. The film thickness is on the micrometer scale and makes conventional methods unsuitable for its toughness characterization. The absence of an accepted method for characterizing the DLC toughness has hindered the related research on the development of toughening methods and understanding the mechanism. This work intends to explore a relatively simple and acceptable characterization method to measure the film toughness. Moreover, toughening mechanisms of DLC films are proposed during the characterization to reveal the toughening mechanism. The toughness can be fully characterized through combining impact toughness and scratch toughness. The impact toughness can be obtained by observing the size of the indentation and the crack state around the indentation in the impact experiment. The scratch toughness could be assessed by combining the scratch morphology and Crack Propagation Resistance (CPRS). The improvement of film toughness should be carried out from two aspects: preventing microcrack initiation and suppressing crack propagation. Appropriate doping of non-carbide metal particles can effectively improve the toughness of the film, and there are seven main factors affecting the toughening of the film. Five toughening mechanisms of non-carbide metals from film preparation to test stage are revealed during the investigation of the change patterns.

We discuss the neutron skins of 48Ca and 208Pb. We review and critically examine modern predictions and empirical constraints, with special attention to the dierent interpretations of the ndings from the PREX-II experiment and the recently reported value of the neutron skin in 48Ca extracted from the CREX experiment. We argue that, in the spirit of the ab initio philosophy, the path to understanding the behavior of dense neutron-rich matter must not circumvent fundamental nuclear forces. Based only on that argument, a thick neutron skin in 208Pb is highly unlikely.

The relationship of the animal with its environment has been of longstanding interest in philosophy and science. Here I provide a brief introduction to concepts that place an emphasis on mutualism as the basis of organism - environment interaction, in contrast to the long standing view that the environment exerts an instrumental role in shaping the organism. Two influential theories have been von Uexküll’s theory of umwelt and Gibson’s theory of affordances. The former envisioned the animal as immersed in its surroundings (umwelt) to form a functional unit. In a similar manner, the latter theory describes a unity between 1) environmental information that provides the animal with opportunities for action (affordances) and 2) the ability of the animal to perceive and engage with those affordances. These views have influenced more recent ecological models of the organism as the functional unit of biology and have also influenced models of immune function. In ecological models, agency is seen as the ability of the organism to predict and control its engagement with the environment in order to maintain its integrity. The predominant contemporary model of neural function in which perception and action are understood to operate through Bayes-like active inference complements the concept of agency as proposed by the mutualism models. However, it is suggested that rather than a constant mutualism, encounters between organism and environment range over a dynamic spectrum from dualism to mutualism. It is also suggested that along this spectrum, agency emerges when the balance of instrumentality shifts from the environment to the organism, and that the balance of this relationship can further progress towards a felicitous mutualism. Meaning emerges between environmental information and an agent as opportunity for action. Implications for opportunities to foster agency in animals within our care is noted.

Dysregulation of the Cyclin-dependent kinase 8 (CDK8) activity has been associated to many diseases including the colorectal and breast cancer. As usual in the CDK family, the activity of CDK8 is controlled by a regulatory protein called cyclin C (CycC). But while human CDK family members are generally activated in two steps that is, the binding of the cyclin to CDK and the phosphorylation of a residue in the CDK activation loop, CDK8 does not require the phosphorylation step to be active. Another peculiarity of CDK8 is its ability to be associated to CycC while adopted an inactive form. These specificities raise the question of the role of CycC in the complex CDK8-CycC, which appears to be more complex than for the other members of CDK family. Through MD simulations and binding free energy calculations, we investigated the effect of CycC on the structure and dynamics of CDK8 on the one hand, and the structural molecular basis of the protein-protein interaction between the two partners on the other hand. We found that CycC has a stabilizing effect on CDK8 and identified specific interaction hotspots within its interaction surface compared to other human CDK/Cyc pairs. Targeting these specific interaction hotspots could be a promising approach in terms of specificity, to effectively disrupt the interaction between CDK8. The simulation of the conformational transition from the inactive to the active form of CDK8 suggests that the residue Glu99 of the CycC may assume the role of the missing phosphorylation step in the activation mechanism of CDK8. In a more general view, these results point the importance of keeping the CycC in computational studies when studying the human CDK8 protein in both the active and the inactive form.

Designing high-voltage underground transmission lines poses complex challenges in heat management, trench optimization, and determining cable ampacity. This article introduces an innovative proposal that focuses on adjusting the dimensions of the thermal backfill as a primary strategy to enhance ampacity compared to the traditional approach of increasing the cross-sectional area of the cable core. The methodology employs a particle swarm optimization (PSO) technique with adaptive penalization, restart strategies, and parameter self-adaptation implemented in MATLAB. The objective of this approach is to provide more efficient solutions than traditional MATLAB PSO, demonstrating improved convergence and more accurate results with a success probability of 66.1\%. Although traditional PSO is 81\% faster, the proposed PSO stands out for its precision. Additionally, the incorporation of thermal backfill results in an 18.45\% increase in cable ampacity. Variations in the thermal resistivity of the soil, backfill, and ambient temperature are highlighted as sensitive factors affecting ampacity and backfill dimensions. This method is presented as a crucial tool in the early stages of the project and underground installation in operation with maximum ampacity, contributing to the continuous improvement of energy efficiency.

We present a thermodynamic approach in modeling the evolution of the universe based on a theory that space consists of energy quanta, the spaceons. From wave-particle duality, they can be treated as an ideal gas. The model is similar to the Big Bang but without Inflation. It provides an insight into the nature of dark energy and dark matter, and an explanation for the accelerated expansion of the universe. The universe started from an atomic size volume of spaceons at very high temperature and pressure. Upon expansion and cooling, phase transitions occurred resulting in the formation of fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters due to the action of gravity. From the cooling curve of the universe we constructed a thermodynamic phase diagram of cosmic composition, from which we obtained the correlation between dark energy and the energy of space. Using Friedmann’s equations, our model fits well the WMAP data on cosmic composition with an equation of state parameter, w= -0.7. The dominance of dark energy started at 7.25 x 10⁹ years, in good agreement with BOSS measurements. The expansion of space is attributed to a scalar quantum space field. Dark Matter is identified as a plasma form of matter similar to that which existed during the photon epoch, prior to recombination. The thermodynamics of expansion of the universe was adiabatic and decelerating during the first 7 billion years after the Big Bang; it accelerated thereafter. A negative pressure for Dark Energy is required to sustain the latter. This is consistent with the theory of General Relativity and the law of conservation of energy. We propose a mechanism for the acceleration as due to consolidation of matter forming Dark Energy Stars (DES) and other compact objects. The resulting reduction in gravitational potential energy feeds back energy for the expansion. Space will continue to expand and dark energy will undergo phase transition to a Bose-Einstein condensate, a superfluid form of matter. Self-gravitation can cause a bounce and start a new Big Bang. We show how the interplay of gravitational and space forces leads to a cyclic, maybe eternal, universe.

The Universe is treated as an unbound thermodynamic system in which two forces of Nature compete: Attractive gravity loss and repulsive entropic gain. Entropic gain, although not presently considered a force of Nature, is otherwise well known and can be expressed with the gas laws. The Universe at the time of last scattering was all gas. Its instant gain is expressed as gas pressure. When the Gibbs equation is properly applied to this unbound gas, the resulting atomic Hubble parameter is found to be exclusively dependent on baryon density, giving a constant and perpetual two-to-one gain/loss ratio. Instant loss to gravity cannot offset gas pressure in this “thermal equation”. By contrast, the Friedmann equation, a ΛCDM foundation, treats baryon mass as accreted, having little if any entropic gain. These two equations are actually equivalent. Expanding accreted matter at its comoving critical density is herein shown to behave exactly like a freely expanding gas. However, neither equation includes all of today’s Universal kinetic energy, and cannot by themselves fully account for observed stellar movement. The present paper proposes the plausible existence of highly energetic or “suprathermal” free electrons which comprise about half of the intergalactic medium’s kinetic total. It is this suprathermal energy which Λ expresses. The fluid equation, another ΛCDM foundation, eliminates entropic gain from the Gibbs equation. Additionally, rest mass’s Einstein energy E=Mc² is treated as a thermal variable. These two assumptions, isoentropy and energy conflation, led astronomers to populate Λ as they followed the prior art.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

In transient phase of an atmospheric-pressure discharge, the avalanche turns into a streamer discharge with time. Hydrodynamic fluid models are frequently used to describe the formation and propagation of streamers, where charge particle transport is dominated by the creation of space charge. The required electron transport data and rate coefficients for the fluid model are parameterized using the local mean-energy approximation (LMEA) and the local field approximation (LFA). In atmospheric pressure applications, the excited species produced in the electrical discharge determine the subsequent conversion chemistry. We performed the fluid model simulation of streamers in nitrogen gas at atmospheric pressure using three different parametrizations for transport and electron excitation rate data. We present the spatial and temporal development of several macroscopic properties such as electron density and energy, and the electric field during the transient phase. The species production efficiency which is important to understand the efficacy of any application of non-thermal plasmas is also obtained for the three different parametrizations. Our results suggest that at atmospheric pressure all three schemes predicted essentially the same macroscopic properties. Therefore, a lower order method such as LFA which does not require the solution of the energy conservation equation should be adequate to determine the streamer macroscopic properties to inform most plasma-assisted applications of nitrogen containing gases at atmospheric pressure.

Creep deformation behaviour in single phase γ-TiAl alloy has been an extensively studied topic since the late 1970s. A lot of literatures have reported creep behaviour of γ-TiAl alloys, manufactured using different processing techniques [1]–[7]. The present discussion revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase γ-TiAl alloy by Hayes et al. [8] and is aimed to develop an understanding of steady state creep, through strain vs strain rate and strain vs ln(strain rate) plots. Besides, it also attempts to study the variation of stress exponent with temperature between 760-900⁰C and also, to determine activation energies using the two most common approaches, namely: Zener-Hollomon (Z-H) [9] and Sherby-Dorn (S-D, temperature compensated time approach) [10] for stress levels of 69 and 103.4 MPa between 760-900⁰C.

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

Induction machines drive many industrial processes, and their unexpected failure can cause heavy production losses. The analysis of the current spectrum can identify online the characteristic fault signatures at an early stage, avoiding unexpected breakdowns. Nevertheless, frequency domain analysis requires stable working conditions, which is not the case for wind generators, motors driving varying loads, etc. In these cases an analysis in the time-frequency domain -such as a spectrogram- is required for detecting faults signatures. The spectrogram is built using the short frequency Fourier transform, but its resolution depends critically on the time window used to generate it: short windows provide good time resolution, but poor frequency resolution, just the opposite than long windows. Therefore, the window must be adapted at each time to the shape of the expected fault harmonics, by highly skilled maintenance personnel. In this paper, this problem is solved with the design of a new multi-band window, which generates simultaneously many different narrow-band current spectrograms, and combines them into a single, high resolution one, without the need of manual adjustments. The proposed method is validated with the diagnosis of bar breakages during the start-up of a commercial induction motor.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

Relying on the United Arab Emirates (UAE) extract from the cross-national data sample on the environmental affection and cognition of adolescent students, and seemingly unrelated bivariate weighted ordered probit regression modeling, this study adopts a national perspective to investigate the determinants of adolescent students' awareness and expectations about nuclear power technology and nuclear waste in the UAE. Identification of model parameters is achieved through maximum simulated likelihood estimation. The findings show that each level increase in UAE youth's interest in ecosystem services and sustainability raises their awareness of nuclear electrical power and nuclear waste by 13.5%, while reducing by 2.4% their level of optimism towards the technology. Furthermore, we find significant heterogeneity in youth awareness and expectations about nuclear power technology across the seven Emirates. Accounting for all other factors (including interest in ecosystem services), UAE youth awareness about nuclear electrical power technology appears to not significantly influence their expectations about the evolution of this technology for the next 20 years. Given that the UAE first nuclear power plant ``Barakah'' is scheduled to start operations end of 2019 beginning 2020, and the typical long life-span of nuclear wastes, our results provide important insights for developing sustainable nuclear energy policies and establishing a long-term nuclear energy program in the UAE.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

The concept of ecosystem services (ESs) provides a valuable approach to communicate societies' dependence on natural ecosystems, assisting in the evaluation of measures to protect vegetation in watersheds that promote water-related ESs. Vegetation cover and land use are important factors related to the capacity of ecosystems to provide soil loss regulation and sediment retention services, which are highly relevant for sediment management in watersheds draining into reservoirs with multiple water uses. This study aims to assess the relationship between potential changes in land use and land cover and the sediment retention service provided by riparian vegetation in a watershed draining into a hydroelectric reservoir in the Brazilian Cerrado. Sediment load was selected as a physical variable that affects different water uses in reservoirs, with these uses being dependent on the quality or quantity of stored water. Scenarios were analyzed to represent landscape reconfigurations from a baseline condition in order to account for the recovery of riparian vegetation by the agricultural sector, as foreseen in the Brazilian Forest Code. To map and quantify variations in annual sediment retention, the InVEST model was used, which allows estimating an integrated response of the drainage basin to large-scale land use changes over time and space. The results show that for the drainage basin of the Corumbá IV Hydroelectric Power Plant (HPP), the recovery of riparian areas occupied by annual crops has the potential to generate greater benefits to water use in the reservoir. In the studied catchment area, 14% of the total vegetation deficit in riparian areas is occupied by crops, while 86% is occupied by pastures. This highlights the buffering role of riparian vegetation as an effective practice for managing sediment flows originating from sheet erosion in agricultural landscapes. The methodology employed in this study allows for the quantification and mapping of the effects of soil and water conservation measures in river basins. This enables the prioritization of sectoral efforts for the restoration of native vegetation, considering the highest returns in benefits perceived by water users affected by sediment input in reservoirs. The study's results reinforce the importance of conserving vegetation in riparian areas and their surroundings for sediment retention, highlighting the role of these areas as assets in providing water-related ecosystem services.

In the context of "dual carbon", with the continuous deepening of the power system reform, the application of high proportion renewable energy is becoming increasingly widespread. All sectors of society have put forward higher requirements for electricity sales packages, which can guide the behavior of power users, promote energy conservation and emission reduction, and finally promote low-carbon operation of the power market economy.Therefore, the requirements of power users and power selling companies for the power selling package are increasing, which puts forward higher requirements to the power selling package recommended by the power selling company . However, the existing recommendation methods are unable to make appropriate recommendations for the users with lack of preference information. Therefore, this paper proposes a two-sided matching decision-making method of electricity sales package based on disappointment theory. First of all, according to the incomplete fuzzy preference relationship provided by the power user and the electricity sales package, the respective priority weight vector is obtained, and then the subjective satisfaction matrix of the power user and the electricity sales package to each other is obtained; Next, the adjusted satisfaction matrix is calculated by adding the influence of the theory of joy and disappointment; Then, based on the adjusted satisfaction matrix, an optimization model aiming at maximizing the total satisfaction of power users and electricity sales packages is established, and the optimal stable matching model of power users and electricity sales packages is obtained; Finally, taking an industrial park in Zhejiang Province as an example, by using the bilateral matching method proposed in this article, the optimal matching schemes for 5 power users and 6 electricity sales packages are obtained, which shows the effectiveness and rationality of the two-sided matching decision-making method of electricity sales package based on the disappointment theory proposed in this paper.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

The cosmological relevance of emptiness—that is, space without bodies—is not yet sufficiently appreciated in natural philosophy. This paper addresses two aspects of cosmic emptiness from the perspective of natural philosophy: the distances to the stars in the closer cosmic environment and the expansion of space as a result of the accelerated expansion of the universe. Both aspects will be discussed from both a historical and a systematic perspective. Emptiness can be interpreted as “coming” in a two-fold sense: Whereas in the past knowledge of emptiness as it were came to human beings, in the future it is coming insofar as its relevance in the cosmos will increase.The longer and more closely emptiness was studied since the beginning of modernity, the larger became the spaces over which it was found to extend. From a systematic perspective, I will show with regard to the closer cosmic environment that the earth may be separated from the perhaps habitable planets of other stars by an emptiness that is inimical to life and cannot be traversed by humans. This assumption is a result of the discussion of the constraints and possibilities of interstellar space travel as defined by the known natural laws and technical means. With the accelerated expansion of the universe, the distances to other galaxies (outside of the so-called local group) are increasing. According to the current standard model of cosmology and assuming that the acceleration will remain constant, in the distant future this expansion will lead first to a substantial change in the epistemic conditions of cosmological knowledge and finally to the completion of the cosmic emptiness and of its relevance, respectively. Imagining the postulated completely empty last state leads human thought to the very limits of what is conceivable.

The paper considers the issues of structural stability, electronic properties, and phonon dispersion of the cubic, tetragonal, and monoclinic phases of ZrO2. It was found that the monoclinic phase of zirconium dioxide is the most stable among the other two phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic values. The smallest negative modes were found for m-ZrO2. An analysis of the electronic properties showed that during the m–t phase transformation of ZrO2, the Fermi level first shifts by 0.125 eV towards higher energies, and then decreases by 0.08 eV in the t–c cross section. The band gap for c-ZrO2, t-ZrO2, and m-ZrO2 is 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35 and 16.15 mol. %Y2O3 on the m-ZrO2 structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO2 and an increase in their defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that not only for pure systems, including those doped with Y2O3, the main contribution to the formation of the conduction band is made by the p-states of electrons. An analysis of the mechanism of water adsorption on the surface of t-ZrO2 (101) and t-YSZ (101) showed that H2O on unstabilized t-ZrO2 (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom.

Nuclear technologies have the potential to play a major role in the transition to a global net-zero society. Their primary advantage is the capability to deliver controllable 24/7 energy on demand. However, as a prerequisite for successful worldwide application, significant innovation will be required to create the nuclear systems of the 21st century, the need of the hour. The pros and cons of nuclear are discussed and analysed at different levels – the societal and public recognition as well as the scientific/engineering and economic level – to assure a demand driven development. Based on the analysis of the different challenges a vision for the nuclear system of the 21st century is synthesised consisting of three pillars – unlimited nuclear energy, zero waste nuclear, and accident free nuclear. These three combined visions are then transformed into dedicated and verifiable missions which are discussed in detail regarding challenges and opportunities. In the following a stepwise approach for the development of such a highly innovative nuclear system is described. Essential steps to assure active risk reduction and the delivery of quick progress are derived as answer to the critique on the currently observed extensive construction time and cost overruns on new nuclear plants. The 4-step process consisting of basic studies, experimental zero power reactor, small scale demonstrator, and industrial demonstrator is described. The 4 steps including sub-steps deliver the pathway to a successful implementation of such a ground breaking new nuclear system. The potential sub-steps are discussed with the view not only onto the scientific development challenges, but also as an approach to reduce the regulatory challenges of a novel nuclear technology.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Vegetation has a significant influence on velocity distribution and turbulent energy in a confluence channel. A laboratory measurement with ADV was used to investigate the flow through a Y-shaped confluence channel partially covered with rigid vegetation on its inner bank. In this study, the flow velocities in cases with and without vegetation were measured by the ADV in a Y-shaped confluence channel. The results clearly show that the existence of non-submerged rigid plants has changed the internal flow structure, that the velocity in the non-vegetated area is greater than in the vegetated area, and that there is a large exchange of mass and momentum between the vegetated and non-vegetated areas. The velocity on both sides is significantly reduced when vegetation is present. In the vicinity of tributaries, due to the presence of vegetation, the high-velocity area moved rapidly to the middle of the non-vegetated area, and the secondary flow phenomenon disappeared. In the mainstream, when vegetation was present, circulation disappeared, and the degree of lateral mixing decreased. The presence of vegetation caused a great change in the internal flow structure and made the flow in non-vegetated areas more intense.

This case report describes evidence of intratubular biomineralization in root canal filled with calcium enriched material after 8 years of clinical maintenance. The schematic findings of dentinal tubules were investigated with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The root canal obturation material was closely adapted to root dentin surface, suggesting the possibility of chemical bonding between the two interfaces. SEM and EDS observation of dentinal tubules showed intratubular biomineralized crystal structures with Ca/P ratio in a range of 1.30–2.12, suggesting bioactive capacity of calcium enriched cement.

Widely used estimates of food-insecure populations are likely to be biased upwards, lacking adjustment for global increases in sedentary behavior in recent decades. We first construct a household model to account for sedentary choices during leisure and work time decisions. The model rationalizes increasing sedentary behavior from the household by accounting for increasing returns to cognitive human capital vs physical capital, alongside increased productivity of more sedentary activities both at work and at home. The household model then informs an empirical model that makes use of our unique international pseudo-panel data on sitting time, which serves as a proxy for sedentarism. We econometrically estimate a transfer function linking sedentarism to widely available covariates, which then are used to make out-of-sample predictions and can be applied to a large set of countries. The estimated sedentary time can be used to adjust the physical activity level reflected in the minimum dietary energy requirement used to determine a cutoff for food insecurity.

Biothermodynamics of viruses is among the youngest, but rapidly developing scientific disciplines. During the COVID-19 pandemic, it has closely followed the results published by molecular biologists. Empirical formulas were published for 50 viruses and thermodynamic properties for multiple viruses and virus variants, including all variants of concern of SARS-CoV-2, SARS-CoV, MERS-COV, Ebola virus, Vaccinia and Monkeypox virus. A review of development of biothermodynamics of viruses during the last several decades and intense development during the last 3 years has been described in this paper.

Multi-gap Resistive Plate Chamber has been attracting increasing attention and has been studied in recent decades because of its good efficiency, high time resolution and relatively low cost. It has become a new standard technology for the Time of Flight system in particle and high energy physics experiments. In this paper, we introduce the operation principle and structure of the MRPC detector and review the applications on the Time of Flight system in several famous experiments, such as STAR, CBM and SoLID. The performances including time resolution and particle identification are discussed in detail. Some recent advances and perspectives with regard to the future development of the next generation MRPC are also outlined.

In this paper, optimum parameters of Tuned Mass Dampers (TMD) are considered to control the responses of 10-story shear building under harmonic loading and 22 set of seismic records of FEMA-P695. The criterion used to obtain the optimum parameters is to select mass ratio, the frequency (tuning) and damping ratio that would result in smallest lateral displacements. State-space equations of motion are presented to compute the structural responses by developing a MATLAB file. A 10-story shear building is presented as a case study to assess the effects of TMDs on the multi-story structures. The results indicate that using TMD can reduce structural responses up to the average 20% under earthquake excitation and up to 90% under harmonic loadings. TMDs are not always effective under any type of ground motion; therefore, being aware of the given location is significant to design TMDs properly.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

In this article, the main building of the former Uto City Hall, which was severely damaged in the 2016 Kumamoto earthquake, is investigated as a case study for the retrofitting of an irregular Reinforced Concrete building using the base-isolation technique. Its peak response is predicted via mode-adaptive bidirectional pushover analysis (MABPA), which was originally proposed by the authors. In the prediction step of MABPA, the peaks of the first and second modal responses are predicted considering the energy balance during a half cycle of the structural response. The numerical analysis results show that the peak relative displacement can be properly predicted by MABPA. The results also show that the performance of the retrofitted building models is satisfactory for the ground motion considered in this study, including the recorded motions in the 2016 Kumamoto earthquake.

In this review we collect some recent achievements in the accurate and efficient solution of the Nonlinear Schrödinger Equation (NLSE), with the preservation of its Hamiltonian structure. This is achieved by using the energy-conserving Runge-Kutta methods named Hamiltonian Boundary Value Methods (HBVMs) after a proper space semi-discretization. The main facts about HBVMs, along with their application for solving the given problem, are here recalled and explained in detail. In particular, their use as spectral methods in time, which allows efficiently solving the problems with spectral space-time accuracy.

The EU’s energy targets are to achieve at least 32% renewables in the energy mix by 2030. Part of the solution is strengthening consumer rights by empowering individuals to generate their own electricity. The study aimed to identify the most suitable energy system for electricity generation of up to 50 kW in the EU residential sector. The Multi-Criteria Decision Analysis was used to compare four systems: proton exchange membrane fuel cell with photovoltaic panels, photovoltaic panels, biomass powered Stirling engine, and solar powered Stirling engine. Based on the results, the most beneficial system for household electricity generation is the Biomass-fueled Stirling engine system due to its affordability, reliability, and low environmental impact. Governments and businesses can use these findings to improve information for the residential sector and enable the transition to renewable energy.

The interaction between spinors and gravity is the most complicated and subtle interaction in the universe, which involves the basic problem to unified quantum theory and general relativity. By means of Clifford Algebra, a unified language and tool to describe the rules of nature, this paper systematically discusses the dynamics and properties of spinor fields in curved space-time, such as the decomposition of the spinor connection, the classical approximation of Dirac equation, the energy momentum tensor of spinors and so on. To split spinor connection into Keller connection $\Upsilon_\mu\in\Lambda^1$ and pseudo-vector potential $\Omega_\mu\in\Lambda^3$ by Clifford algebra not only makes the calculation simpler, but also highlights their different physical meanings. The representation of the new spinor connection is dependent only on the metric, but not on the Dirac matrix. Keller connection only corresponds to geometric calculations, but the potential $\Omega_\mu$ has dynamical effects, which couples with the spin of a spinor and may be the origin of the celestial magnetic field. Only in the new form of connection can we clearly define the classical concepts for the spinor field and then derive its complete classical dynamics, that is, Newton's second law of particles. To study the interaction between space-time and fermion, we need an explicit form of the energy-momentum tensor of spinor fields. However, the energy-momentum tensor is closely related to the tetrad, and the tetrad cannot be uniquely determined by the metric. This uncertainty increases the difficulty of deriving rigorous expression. In this paper, through a specific representation of tetrad, we derive the concrete energy-momentum tensor and its classical approximation. In the derivation of energy-momentum tensor, we obtain a spinor coefficient table $S^{\mu\nu}_{ab}$, which plays an important role in the interaction between spinor and gravity. From this paper we find that, Clifford algebra has irreplaceable advantages in the study of geometry and physics.

Newton's kinetic energy equation delineates the laws of motion for objects travelling at speeds much less than the speed of light, an equation extensively validated at these lower velocities. Any new, more complete formulation of kinetic energy must approximate Newton's kinetic energy equation under these conditions. Einstein's special relativity, utilizing the Lorentz factor, introduces a new perspective on spacetime, adhering to the requirement that the Newtonian kinetic energy equation serves as an approximation at low velocities. In this paper, we identify all factor expressions satisfying the condition that their approximate solutions at low velocities align with Newton's kinetic energy equation. We introduce the Yuyunrui factor, incorporating two real number hyperparameters, $\alpha$ and $\beta$, encompassing all potentially correct factors, with the Lorentz factor as a specific instance where $(\alpha=0$, $\beta=1)$. We classify all potentially correct $(\alpha, \beta)$ combinations into six categories based on their distinct scaling effects and present the corresponding scaling effects. The combinations of $(\alpha, \beta)$ values applicable in the real world are necessarily included within these candidates, with the precise values requiring rigorous experimental validation. This work aims to refine our understanding of special relativity beyond the Lorentz factor.

Phosphorus is required by laying hens for a variety of biological functions. It is usually provided in excess, in a readily digestible inorganic form in diet formulations. However, this does not represent an efficient use of a finite resource and can result in water pollution. Plant bound phosphorus in phytate, is common in commercial poultry diets, and represents an alternate source of phosphorus, however poultry lacks the enzyme to digest it. By adding enzymes to their diets, the availability of this phytate-bound phosphorus can be increased allowing for the reduced inclusion of inorganic P in the diet formulation. Therefore, this study was conducted to examine the effect of a natural enzyme complex that contains phytase and xylanase in layer diets. Novogen Brown Classic layers (n=314) were fed one of two diets: (T1) control diet or (T2) control diet plus a natural mixed-enzyme product with both, phytase and xylanase. Experimental diets were provided for 12 days after which the excreta from each pen were collected for an additional three days to determine total retention and ileal digestibility of phosphorus and gross energy. At the end of the trial the birds were euthanized, and their ileal contents were collected. Productivity parameters were also recorded over the course of the study. The amount of phosphorus detected in the excreta of the control group was significantly higher than the amount detected in the enzyme-supplemented group (P<0.05). Both phosphorus retention and phosphorus ileal digestibility were significantly higher in the enzyme-supplemented birds (P<0.001). Gross energy digestibility was significantly higher in the enzyme-supplemented birds for both the total tract and ileal samples (P<0.001). There were only numerical improvements, not significant, in the layer productivity parameters. This study showed that the enzyme supplement can improve total retention and ileal digestibility of phosphorus and gross energy in older layers.

The energy crisis is currently a major topic in scientific and managerial discussions in the building and construction industry. While employing low-cost strategies for reducing energy usage is beneficial for principals and decision-makers, the primary purpose of this study is to recommend the use of phase change materials (PCM) to improve cooling and heating load management in buildings. In order to accomplish this, the study applies design-builder simulations to a developing country case study. The results indicate that integrating PCM in buildings can reduce energy usage by around 6 percent. Although this value may be lower than other techniques, it is nevertheless important for reaching green building goals in both developed and developing nations. The case study, which takes place in a four-season region, demonstrates the significant potential of the PCM system for both cooling and heating energy management. In addition, the reciprocal performance improvement of PCMs is a remarkable characteristic, especially when contrasted to some conventional systems that focus on a single energy management objective in buildings. Lastly, it should be underlined that the suggested platform is consistent with Sustainable Development Goal 7 (Affordable and Clean Energy Targets).

Atrial Fibrillation (AF) is known as one of the dominant cardiac disease that is associated with severe consequences such as risk of strokes. This cardiac arrhythmia can be efficiently diagnosed using EEG signals. However, AF episodes in EEG records are not always permanent for all subjects. In addition, lengthy subject preparation and ECG recording sessions makes this practice time consuming and not attractive for efficient diagnosis. One attractive solution for this problem will be the use of wearable Internet of Medical Things IoMT devices for EEG recording and AF detection. From another side the use machine learning for efficient diagnosis could provide high accurate diagnosis. However, the deployment of these wireless wearable devices faces the problems of limited processing capabilities and of energy scarcity. In this context, the design of energy efficient accurate on-sensor AF detection scheme using machine learning algorithms still requires a focused research effort. This paper proposes a wearable solution for ECG-based processing scheme for embedded AF detection. The proposed method achieved 100% sensitivity and 94.5% of specificity and accuracy of around 97.4 % for wide range of subjects while showing low energy-consumption. The obtained results show the efficiency of using Logistic Regression algorithm for accurate AF detection and attest about practical feasibility of the proposed approach in wearable IoMT devices.

The Semiconductor and Liquid Assisted Photothermal Effect (SLAPE)” concept was employed for the first time in this study to generate electricity from sunlight. In SLAPE process, a semiconducting material is immersed completely in a stable organic solvent to capture the complete sunlight reaching the earth surface and to turn it into the heat-energy that can be eventually converted into electricity by using Organic Rankine Cycle (ORC) with the help of a heat engine and electric generator. In this investigation, the SLAPE solar panels were fabricated with two top and bottom chambers separated by thin thermally conducting metal sheet (Cu or Al). Multi-crystalline silicon photovoltaic cells (SPVCs) in conjunction with -butyrolactone were employed to capture the sunlight, and a low-boiling point dichloromethane (DCM) solvent was employed as a working fluid to capture the in situ generated heat energy from sunlight. Upon exposure to the natural sunlight, the 21 numbers of SPVCs together with about 2 litres -butyrolactone containing one square meter area SLAPE solar panel has generated about 17 V when integrated with a laboratory model reciprocally moved steam engine and a custom-made electric generator, whereas, a commercial SPVC solar panel with 21 number SPVCs generate a maximum voltage of 11 V. The theoretical background governing the SLAPE solar panels, the necessity for their invention and the proof of concept of SLAPE solar panels have been thoroughly presented and discussed and established in this article.

The power system has rapidly grown and expanded over the past decades and has been experiencing major changes and challenges. The increase in energy demand and the modern advancements in the smart grid, such as solar and wind energies and electric vehicles, have led to complexity and complications for utilities. A further layer of complexity and difficulty was added by the rapid expansion of behind-the-meter (BTM) photovoltaic (PV) systems with various designs and characteristic features. The rapid increase and the invisible solar power (BTM) have led to fluctuations in power grid stability and reliability and to inefficiency. Accurate forecasting of load generation will help to assure optimal planning, minimize the negative effects of the PV systems, and minimize the operational and maintenance costs. The authors propose a solution that uses combinations of K-means clustering with neural network machine learning models, AMI real-world PV load generation, and weather data to forecast the generation load at customer locations to achieve a 2.49% error between actual and predicted generation load.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

The implementation of residential distributed generation (DG) in South America has shown significant growth in the last decade, driven by increased research on photovoltaics and renewable energy sources. Regulatory policies and business models have been crucial in fostering the adoption of DG in the region, with residential self-supply being the most receptive sector for implementing the concept. This article presents a literature review on DG as applied to residential self-supply in South America by comprehensively analyzing documents published between 2013 and 2023, applying the PRISMA methodology. In total, 37 literature resources have been systematically selected and reviewed to contribute to the identification of trends and developments in the field of DG in the residential sector, as well as highlighting areas that require further research and attention from stakeholders, including policymakers, investors, technology providers and consumers in the South American context.

In response to the growing demand for high-strength and high-toughness materials in industries like aerospace and automobiles, there is a need for metal matrix composites (MMCs) that can simultaneously enhance strength and toughness. This paper focuses on the design configurations of MMCs, which include both the configurations resulting from reinforcements and the inherent heterogeneity of the matrix itself. The mechanical properties of MMCs are influenced by factors such as reinforcement content, shape, size, and spatial distribution within the composite architecture. Among them, Aluminum matrix composites (AMCs) are particularly significant in aerospace, electronics, and electric vehicles due to their potential for weight reduction and enhanced performance. However, the challenge lies in the inverse relationship between strength and toughness, hindering the widespread utilization and large-scale development of MMCs. The design configuration of composites plays a critical role in achieving concurrent improvements in strength and toughness. This review explores the advantages of toughness, toughening mechanisms, reinforcement distribution characteristics, and structural parameters in the design of composite architectures. Drawing inspiration from biological composites like bone, the development of synthetic composites with homogeneous structural designs provides insights into attaining exceptional strength and toughness in lightweight engineering structures. Additionally, understanding fracture behavior and toughening mechanisms in heterogeneous nanostructures is vital for advancing the field of metal matrix composites. Summarily, the design of composite architectures holds tremendous potential for tailoring AMCs with outstanding strength and toughness, addressing the requirements of lightweight engineering structures in various industries.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

We present a theoretical modeling of a cylindrical tunable liquid crystal lens based on the modulation of the anchoring energy. This latter can be easily obtained by means of photoaligning techniques. The liquid crystal cell we propose exhibits strong anchoring at the top substrate and an anchoring energy with parabolic profile at the bottom substrate. The model describes the dependence of the focal length on the applied voltage and presents a theoretical study of lens aberrations. The results obtained are of general relevance and can be used to optimize the performances of every kind of liquid crystal lens with parabolic profile.

The free energy principle (FEP) is a mathematical and scientific principle that describes the relationship between the physical behavior of a dynamical system and the interpretation of such behavior as carrying out inference. It blurs the boundary between the ontological mode of the system of interest and the epistemological significance it acquires through its dynamic interaction with the environment. New materialism (or neo-materialism), despite lacking a single definition, refers to a range of emerging perspectives that attempt to dismantle the long-held divisions between ontology, epistemology, and even ethics, with the aim of achieving a comprehensive transformation of naturalized thinking. In this context, new materialism provides powerful tools to reframe some of the conceptual foundations of the FEP. This paper is the first in a series that aims to systematically construct a neo-materialistic perspective for the FEP, exploring its wide-ranging implications. It serves as an introduction to the series, arguing for the justification of deploying new materialism to reframe the FEP and introducing some essential concepts to be utilized in developing a neo-materialistic account of the FEP.

The COVID-19 epidemic and the measures adopted to contain it have had a significant impact on energy patterns throughout the world. The pandemic and movement restrictions led to unpredictable fluctuations in power systems demand and the fuel price for a delayed period. Monkeypox, another viral disease, appeared during the post-COVID period. It is assumed that the outbreak of monkeypox is unlikely due to the implication of preventive measures experienced by COVID-19. At the same time, the probability of an epidemic cannot be blindly overlooked. This paper aims to examine and analyze historical data to look at how much petroleum fuel was used for generating power and how the price of petroleum fuel changed over seven years, from January 2016 to August 2022. This period covers the time before the COVID-19 pandemic, during the pandemic, and after the pandemic. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and Snaïve), Seasonal and Trend decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods have been applied for both fuel consumption and price prediction. The best forecasting method for fuel price and consumption has been identified among these methods. The paper also utilizes the ARIMAX model by incorporating multiple exogenous variables, such as monthly mean temperature, mean fuel price, and mileage of vehicles traveling during a certain period of pandemic lock-down. It will assist in capturing the non-smooth and stochastic pattern of fuel consumption and price due to the pandemic by separating the seasonal influence and thus provide a prediction of the consumption pattern in the event of any future pandemic.

In this work we report recent theoretical calculations of a superconducting island in a strong vortex confinement regime. The obtained results reveal the evolution of superconducting condensate as a function of electron mean-free path (l) with the evolution of an applied magnetic field H0. The results of this study provide an insight about the emergent superconducting properties under such conditions, using the Ginzburg-Landau numerical simulations where spatial variation of thickness d on island, omnipresent in these kind of structures grown on Si (111), is taken into account. These results offer a new route to tailor superconducting circuits by using the controlled bombardment, in order to explore the impact on vortex distribution, phase of order parameter, number of vortices, free energy and the first H1 and second critical field H2.

It is often claimed that Einstein is wrong about quantum mechanics. However, when comparisons are made with respect to theoretical foundations rather than experimental results Einstein’s theories are found to be superior. Although quantum mechanics correctly predicts what it is possible to observe (the emissions) it ignores the other half of natural phenomena, what cannot be observed (the absorptions), thereby violating the conservation laws. By describing only one-half of radiation processes conceptual difficulties such as wave function collapse, infinite paths, and inscrutable mathematics seem to be insoluble mysteries. The deficiencies are corrected by introducing Hamilton’s principle S = ∫ Ldt and applying the methods of quantum field theory to derive relativistic equations of motion. The calculus of variations is used to show that the wave function represents an incomplete equation of motion because it equals twice the allowable action minimum.

We still do not have satisfactory answers about the inflationary and accelerating expansions of the universe, the missing mass problem, and the origins of the four fundamental forces and the quantum phenomena. Here, we introduce a new model of matter and space and a postulate on a constant of motion, and then show that an equation of motion derived from the constant of motion could provide new understandings of the above problems. For example, we show that there is a natural inflation scenario and that the co-moving distance to the closest accelerating supernova is clearly given as $c/(\sqrt{3} H)$ ($\sim$8.1 billion ly). In addition, we show that, in a system including a proton and an electron, the equation of motion has eight acceleration terms, some of which are suspected to be responsible for the four fundamental forces and the galaxy rotation anomaly. From further discussion, we conjecture that in order to understand the gravitational and strong interactions and the quantum phenomena, it is necessary to consider the expansion of the universe. The lensing mass distribution is explained, based on another postulate on a method of representing superposition.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

This paper presents the implementation of a control strategy based on fuzzy logic artificial intelligence (AI) for speed regulation of an electromagnetic frequency regulator (EFR) prototype, aiming to eliminate the dependence on knowledge of physical parameters in the most diverse operating conditions. Speed multiplication is one of the most important steps in power generation wind. Gearboxes are generally used for this purpose. However, they have a reduced lifespan and a high failure rate and are still noise sources. The search for new ways to match the speed (and torque) between the turbine and the generator is an important research area to increase the energy, financial and environmental efficiency of wind systems. The EFR device is an example of an alternative technology that this team of researchers has proposed. It counts the fact of taking advantage of the main advantages of an induction machine with the rotor in a squirrel cage positively. In the first studies, the EFR control strategy consisted of the conventional PID controllers, which has several limitations widely discussed in the literature. This strategy also limits the EFR's performance, considering its entire operating range. The simulation program was developed using the Matlab/Simulink platform, while the experimental results were obtained in the laboratory emulating the EFR-based system. The EFR prototype used has 2 poles, a nominal power of 2.2 kW, and a nominal frequency of 60 Hz. Experimental results were presented to validate the efficiency of the proposed control strategy.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

The classical uncertainty principle inequalities were imposed as a mathematical constraint over the general relativity geodesic equation. In this way, the uncertainty principle was reformulated in terms of the proper space-time length element, Planck length and a geodesic-derived scalar, leading to a geometric expression for the uncertainty principle (GeUP). This re-formulation confirmed the necessity for a minimum length for the space-time line element in the geodesic, dependent on a geodesic-derived scalar which made the expression Lorentz-covariant. In agreement with quantum gravity theories, GeUP required the imposition of a perturbation over the background Minkowski metric unrelated to classical gravity. When applied to the Schwarzschild metric, a geodesic exclusion zone was found around the singularity where uncertainty in space-time diverged to infinity.