To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and >115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

The effect of COVID-19 confinement regulations on air quality in the northwestern Alps is here assessed based on measurements at five valley sites in different environmental contexts. Surface concentrations of nitrogen oxides, ozone, particle matter, together with size, chemical, and optical (light absorption) aerosol properties, complemented by observations along the vertical column are considered. The 2020 concentration anomalies relative to previous years’ average are compared with the output of a machine learning algorithm accounting for weather effects and a chemical transport model, their difference being within 10–20 %. Even in the relatively pristine environment of the Alps, the «lockdown effect» is well discernible, both in the early confinement phase and in late 2020, especially in NOx concentrations (NO decreasing by >80 % and NO2 by >50 %). While ozone shows little variation, secondary aerosols increase due to enhanced transport from the neighbouring Po basin and coarse particles decrease due to missing resuspension by traffic and, in the city, to the shutdown of a steel mill. The NO2 vertical column density decreases by >20 %, whereas the aerosol profile is mainly influenced by large-scale dynamics, except a shallow layer about 500 m thick possibly sensitive to curtailed surface emissions.

This work examines the effects of two problematic trends in diesel passenger car emissions – increasing NO2/NOx ratio by conversion of NO into NO2 in catalysts and a disparity between the emission limit and the actual emissions in everyday driving – on ambient air quality in Prague. NO2 concentrations were measured by 104 membrane-closed Palmes passive samplers at 65 locations in Prague in March-April and September-October of 2019. NO2 concentrations measured by city stations during those periods were comparable with the 2016-2019. The average measured NO2 concentrations at the selected locations, after correcting for the 18.5% positive bias of samplers co-located with a monitoring station, were 36 µg/m3 (range 16-69 µg/m3, median 35.3 µg/m3), with the EU annual limit of 40 µg/m3 exceeded at 32% of locations. The NO2 concentrations have correlated well (R2=0.76) with the 2019 average daily vehicle counts, corrected for additional emissions due to uphill travel and intersections. In addition to expected “hot-spots” at busy intersections in the city center, new ones were identified, i.e. along a six-lane road V Holešovičkách. Comparison of data from six monitoring stations during March 15-April 30, 2020 travel restrictions with the same period in 2016-2019 revealed an overall reduction of NO2 and even a larger reduction of NO. The spatial analysis of data from passive samplers and time analysis of data during the travel restrictions both demonstrate a consistent positive correlation between traffic intensity and NO2 concentrations along/near the travel path. The slow pace of NO2 reductions in Prague suggests that stricter vehicle NOx emission limits, introduced in the last decade or two, have so far failed to sufficiently reduce the ambient NO2 concentrations, and there is no clear sign of remedy of Dieselgate NOx excess emissions.

Monitoring volatile organic compounds (VOCs) places a crucial role in environmental pollutants control and indoor air quality. In this study, a metal-oxide (MOx) sensor detector (used in a commercially available monitor) was employed to delineate the composition of air containing three common VOCs (ethanol, acetone and hexane) under various concentrations. Experiments with a single component and double components were conducted to investigate how the solvents interact with the metal oxide sensor. The experimental results revealed that the affinity between VOC and sensor was in the following order: acetone > ethanol > n-hexane. A mathematical model was developed, based on the experimental findings and data analysis, to convert the output resistance value of the sensor into concentration values, which in turn can be used to calculate a VOC-based air quality index. Empirical equations were established based on inferences of vapor composition versus resistance trends, and on an approach of using original and diluted air samples to generate two sets of resistance data per sample. The calibration of numerous model parameters allowed matching simulated curves to measured data. As such, the predictive mathematical model enabled quantifying not only the total concentration of sensed VOCs, but also estimating the VOC composition. This first attempt to obtain semi-quantitative data from a single MOx sensor, despite remaining selectivity challenges, is aimed at expanding the capability of mobile air pollutants monitoring devices.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

In air quality management, at urban and regional levels, road transport remains the cornerstone of residential, commercial, and industrial activities, and the vehicle exhaust emissions maintain the position of one of the key contributing sources. In Indian cities, big and small, vehicle exhaust emissions and dust from vehicle movement on the roads, contribute to as much as 50% of particulate matter pollution in a year. So, having access to a vehicle exhaust emissions inventory that is reliable and replicable is critical for air quality management and this exercise starts with access to vehicle stock numbers. These numbers are typically obtained from vehicle registration databases, traffic surveys, and other governmental records, and often require time consuming data cleaning protocols before they can used for emissions and pollution baseline analysis. This paper provides a cleaned and open-access vehicle stock database, as registered and in-use fleet, for the period covering 1993 and 2018, for all India and states, along with an estimate of age-mix of the vehicles using survival functions.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

In this work, we investigate the ability of a data assimilation technique and space-borne observations to quantify and monitor changes in nitrogen oxides (NOx) emissions over North-Western Greece for the summers of 2018 and 2019. In this region, four lignite-burning power plants are located. The data assimilation technique, based on the Ensemble Kalman Filter method, is employed to combine space-borne atmospheric observations from the high spatial resolution Sentinel-5 Precursor (S5P) Tropospheric Monitoring Instrument (TROPOMI) and simulations using the LOTOS-EUROS Chemical Transport model. The Copernicus Atmosphere Monitoring Service-Regional European emissions (CAMS-REG, version 4.2) inventory based on year 2015 is used as the a priori in the simulations. Surface measurements of nitrogen dioxide (NO2) from air quality stations operating in the region are compared with the model surface NO2 output using either the a priori (base run) or the a posteriori (assimilated run) NOx emissions. The high biases found between the in situ NO2 measurements and the base run surface NO2 decrease in the assimilated run in most cases. The bias in the station near the largest power plant decreases to 2.0 μg/m3 (2.83 μg/m3) from 10.5 μg/m3 (8.46 μg/m3) in 2019 (2018 respectively). Concerning the estimated annual a posteriori NOx emissions it was found that, for the pixels hosting the two largest power plants, the assimilated run results in emissions decreased by ~40-50% for 2018 compared to 2015, whereas a larger decrease, of ~70% for both power plants, was found for 2019, after assimilating the space-born observations. For the same power plants, the European Pollutant Release and Transfer Register (E-PRTR) reports decreased emissions in 2018 and 2019 compared to 2015 (-35% and -38% in 2018, -62% and -72% in 2019), in good agreement with the estimated emissions. We further compare the a posteriori emissions to the reported energy production of the power plants during the summer of 2018 and 2019. Mean decreases of about -35% and-63% in NOx emissions are estimated for the two larger power plants in summer of 2018 and 2019, respectively, which are supported by similar decreases in the reported energy production of the power plants (~-30% and -70%, respectively).

This work aimed to assess and characterize the air quality in what concerns particulate pollution in urban-industrial environments. The main objectives were to study the spatial variability of the deposition flux of particulate pollution identifying areas with higher deposition, associate the variability with climatological variables and with possible surrounding emitting sources. The method for collecting the deposited particles was based on the standard NF X 43-007. Sampling for particulate pollution took place between April 2015 and February 2016, through seven sampling campaigns. Maps of the spatial dispersion for the particulate pollution were obtained through statistics and geostatistics techniques. Elemental identification by scanning electron microscopy (SEM) was also used but only in two sampling campaigns. The results show that the sampling campaigns that took place during hot and dry periods, 2nd and 3rd, present higher deposition flux: 2.04 g/(m2 x month) and 1.72 g/(m2 x month), respectively. Lower deposition fluxes were registered in the 6th and 7th campaigns: 0.23 g/(m2 x month) and 0.24 g/(m2 x month), respectively. It was also observed a recurrent high deposition at specific sampling points which may be due to both the nearby road traffic and the presence of chimneys. SEM analysis allowed to associate repetitive element deposition, at the same sampling point, to the same emitting source.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Urban air pollution is a critical global environmental issue, necessitating an understanding of the spatiotemporal characteristics and driving factors for effective environmental protection and urban planning. This study introduced an advanced air quality assessment system that integrates environmental, socio-economic, and urban layout factors, addressing gaps in traditional models that often overlook the impact of urban spatial structures. Analyzing air quality data from Beijing's main urban area (2016-2020) alongside multi-source geographic data, the research develops a comprehensive evaluation system, incorporating 14 key driving factors. Employing Geographically Weighted Regression (GWR) and Multi-scale Geographically Weighted Regression (MGWR), the study quantitatively assessed the influence and spatial heterogeneity of these factors. Findings revealed an annual improvement in air quality, with a U-shaped seasonal pattern and significant spatial clustering (Global Moran’s I = 0.922). The MGWR model, in particular, provided a superior fit over GWR, effectively capturing the spatial variability of factors. Variables such as NDVI), economic output (GDP), and humidity space adjustment capability (HSAC) showed significant positive spatial impacts on air quality, while population density (POP), temperature (TEMP), and road density (RD) exhibited negative effects. These insights enhance the understanding of air pollution dynamics and aid in refining urban planning strategies.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Depending on the characteristics of the industrial area, toxicity evaluation of human body, risk assessment and health impact assessment may directly cause cancer due to air pollution. Environmental data collection is from August 2018 to January 31, 2019, and the average, minimum, and maximum values of air pollution data respectively. According to the global data on global trends using the Big Data, high blood pressure is confirmed at 33rd place in the world, and myocardial infarction among the environmental diseases is confirmed to be lower than Korea. Disease that occurred in Jeolla province industrial complex considering the characteristics of our country was identified as representative. Air pollutants are considered to be the causes of allergic diseases in Korea. PM10 was found to be higher than the control area (28.8804348 (㎍ / ㎥), 31.7065217 (㎍ / ㎥) and 32.8532609 (㎍ / ㎥). The mean concentrations of PM2.5 in the middle and high exposure areas were lower than those of the control areas, but the highest in the intermediate exposure areas was 16.5978261 (㎍ / ㎥), 16.1086957 (㎍ / ㎥) and 17.1847826 (㎍ / ㎥) respectively. The relationship between the major variables of environmental exposure in Yeosu was confirmed to be correlated with high blood pressure, chronic obstructive pulmonary disease (COPD), bronchitis, cerebrovascular, diabetes, thyroid disease, sinus infection, anemia and pneumonia.

Background: Bioaerosol can represent a danger to the health. During SARS-CoV-2 pandemic, portable devices were used in different environments and considered a valuable prevention tool. This study has evaluated the effectiveness of the air treatment device "AEROK 1.0" in reducing microbial, particulate and pollen airborne contamination indoors, during normal activity. Methods: In an administrative room, airborne microbial contamination was measured using active (DUOSAS 360 and MD8) and passive sampling; a particle counter was used to evaluate particle concentrations; a Hirst-type pollen trap was used to assess airborne pollen and Alternaria spores. Statistical analysis was performed using SPSS 26.0; p values

There are numerous hazards found on the farms. Most of them are ignored, which might cause the farmer to pay later in terms of his ill health, potential injuries or death. The current article discusses some of the common issues such as dust and air quality concerns; environmental (weather) stressors and psychological stressors; noise and hearing protection; and tractor safety and seatbelt use. And finally, the recommendations to overcome the hazards are discussed.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

The World Health Organization estimates that every year air pollution kills seven million people worldwide. As it is expected that climate change will affect future air quality patterns, the full understanding of the links between air pollution and climate change, and how they affect human health, are challenges of future research. In this scope, a methodology to assess the air quality impacts on health was developed. The WRF-CAMx modelling framework was applied for the medium-term future climate (considering the SSP24.5 scenario) and for the recent past (considered as baseline). Following the WHO recommendations, mortality health indicators were used to estimate health impacts of long-term exposures. For that, the Aveiro Region, in Portugal, was considered as a case study. Future climate results indicate the occurrence of higher temperatures, and lower total precipitation. Despite that, improvements in the main pollutants’ concentrations, and consequently in the reduction of the related premature deaths are foreseen, mainly due to the reduction of pollutants emissions imposed by the European legislation for the upcoming years. The applied approach constitutes an added value in this research field, being crucial to anticipate the effects of climate change on air quality and evaluate their impacts on human health.

Urination on carpet and subflooring can develop into persistent and challenging to mitigate odor. Very little or no information is published on how these VOCs change over time when urine is deposited on the carpet covering a plywood-type subflooring. This research has investigated the VOCs emitted from carpet+subflooring (control), carpet+subflooring sprayed with water (control with moisture), and cat urine-contaminated carpet+subflooring (treatment) over time (day 0 and 15). In addition, the effect of popular cleaning products on VOCs emitted and evaluated their efficacy in eliminating those indoor odors over time (day 0 and 15). Carpet-subflooring with all treatments were also contaminated with Micrococcus luteus, nonmotile obligate aerobe commonly found in household dust, to observe the impact of the aerobe on carpet-subflooring VOCs emission. VOCs emitted from carpet+subflooring receiving different treatments were collected from headspace using solid-phase microextraction (SPME). The VOCs were analyzed using a multidimensional gas chromatography-mass spectrometer attached to an olfactometry (GC-MS-O). Many common VOCs were released from the carpet on day one and day fifteen, specifically from urine contamination. Cleaning products were effective in masking several potent odors of cat urine contaminated carpet VOCs on day one but unable to remove the odor appeared on day 15 in most cases.

We examine how observations can be used to evaluate an air quality analysis by verifying against passive observations (i.e. cross-validation) that are not used to create the analysis and we compare these verifications to those made against the same set of (active) observations that were used to generate the analysis. The results show that both active and passive observations can be used to evaluate of first moment metrics (e.g. bias) but only passive observations are useful to evaluate second moment metrics such as variance of observed-minus-analysis and correlation between observations and analysis. We derive a set of diagnostics based on passive observation–minus-analysis residuals and we show that the true analysis error variance can be estimated, without relying on any statistical optimality assumption. This diagnostic is used to obtain near optimal analyses that are then used to evaluate the analysis error using several different methods. We compare the estimates according to the method of Hollingsworth Lonnberg, Desroziers, a diagnostic we introduce, and the perceived analysis error computed from the analysis scheme, to conclude that as long as the analysis is optimal, all estimates agrees within a certain error margin. The analysis error variance at passive observation sites is also obtained.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Abstract: This article explores the intricate relationship between environmental degradation, specifically air pollution, and economic growth in the Sultanate of Oman spanning the period from 1990 to 2022. We employ cointegration and vector error correction models to uncover both short- and long-term dynamics in the association between air pollution and economic growth. Fur-thermore, Granger causality analysis is utilized to investigate the causal links between these crucial variables. This data encompasses factors related to environmental quality and various control variables. The empirical results unveil a sustained long-term cointegration connection between the variables. Additionally, our findings highlight a statistically significant positive impact of economic growth and energy consumption on CO2 emissions. Furthermore, the short-term analysis reveals an annual adjustment of approximately 14.1% in N2O emissions dis-equilibrium. The Granger causality study indicates unidirectional causal relationships involving N2O emissions, economic growth, and CO2 emissions. The implications of these findings for Oman's policy landscape are substantial. To effectively reduce greenhouse gas emissions, it is imperative for Oman to establish robust climate change policies. Additionally, the government can play a pivotal role in encouraging and endorsing the use of renewable energy sources, such as green hydrogen, as a promising alternative to traditional oil and gas resources.

As the haze engulfed the Delhi NCR after Diwali there is a panic in public about its causes and consequences. Here are some facts and figures to know the truth behind the scene. Temperature fell down from 24’C on October 31 to 21’C on November 2 as recorded at UPPCB station at sector-125, Noida which is adjacent to Delhi a very strategic location and can be considered as reference point for Delhi-NCR. The details of the study conducted is given below.

During the construction of buildings, dangerous chemicals such as benzene, formaldehyde and others are used, which accumulate during the operation of the building. High concentrations of these substances can harm human health. In this article, we have analyzed the possible impact of modular green wall systems on improving of the air. During the research, four different modular green wall systems and various plant species were considered. The result showed that a modular green wall system can improve the air quality by removing harmful pollutants from the air in the buildings. Urban design used to be turned greener and more sustainable using the modern technologies of modular green wall systems. This study focuses on the air-cleaning benefits provided by modular green wall systems and their assessment. This research contributes to fill existing literature gaps on the green wall systems on the buildings and biophilic architecture.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

Human exposure to infectious aerosols results a transmission of diseases, such as influenza, tuberculosis, and COVID-19. Most dental procedures generate a significant number of aerosolized particles, increasing transmission risk in dental settings. Since the generation of aerosols in dentistry is unavoidable, many clinics started using intervention strategies such as area-filtration units and extraoral evacuation equipment, especially under the relatively recent constraints of the pandemics. However, the effectiveness of these devices in dental operatories has not been studied. Therefore, the dental personnel's ability to position and operate such instruments efficiently is also limited. To address these challenges, we utilized a real-time sensor network for assessment of aerosol dynamics during dental restoration and cleaning producers with and without intervention. The strategies tested during the procedures were (i) local area high-efficiency particle air (HEPA) filters and (ii) extra-oral suction device (EOSD). The study was conducted at the University of Washington School of Dentistry using a network of thirteen fixed sensors positioned within the operatory and one wearable sensor worn by the dental operator. The sensor network provides time and space-resolved particulate matter (PM) data. Three-dimensional (3D) visualization informs aerosol persistence in the operatory. It was found that area filters did not improve the overall aerosol concentration in dental offices significantly. An average of 16% decrease in PM concentration was observed when EOSD equipment was used during the procedures. The combination of real-time sensors and 3D visualization can provide dental personnel and facility mangers with actionable feedback to effectively assess aerosol transmission in medical settings and develop evidence-based intervention strategies.

Ozone and fine particles (PM_2.5) are the two main air pollutants of concern in the New South Wales Greater Metropolitan Region (NSW GMR) region due to their contribution to poor air quality days in the region. This paper focuses on source contributions to ambient ozone concentrations for different parts of the NSW GMR, based on source emissions across the greater Sydney region. The observation-based Integrated Empirical Rate Model (IER) was applied to delineate the different regions within the GMR based on the photochemical smog profile of each region. Ozone source contribution is then modelled using the CCAM-CTM (Cubic Conformal Atmospheric Model-Chemical Transport Model) modelling system and the latest air emission inventory for the greater Sydney region. Source contributions to ozone varied between regions, and also varied depending on the air quality metric applied (e.g., average or maximum ozone). Biogenic volatile organic compound (VOC) emissions were found to contribute significantly to median and maximum ozone concentration in North West Sydney during summer. After commercial domestic, power station was found to be the next largest anthropogenic source of maximum ozone concentrations in North West Sydney. However, in South West Sydney, beside commercial and domestic sources, on-road vehicles were predicted to be the most significant contributor to maximum ozone levels, followed by biogenic sources and power stations. The results provide information which policy makers can devise various options to control ozone levels in different parts of the NSW Greater Metropolitan Region.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

This study investigates the evolving corporate governance mechanisms within the context of an emerging economy. Addressing a literature gap, we analyse the influence of corporate governance and earnings quality on idiosyncratic risk in an emerging economy. In particular, this research explores the impact of corporate governance practices and earnings quality on idiosyncratic risk. For this purpose, we utilise a sample of 75 non-financial firms listed on the Pakistani equity market over nine years from 2010 to 2018. Employing the generalised method of moments, the findings of our empirical analysis reveal that firms with robust governance mechanisms and higher earnings quality experience minimal idiosyncratic risk. These outcomes provide valuable insights for standard setters, regulatory authorities, policymakers, and other stakeholders, emphasising the importance of governance mechanisms and earnings management in mitigating idiosyncratic return volatility.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

Air pollution is a critical issue impacting urban environments, leading to severe health problems and environmental degradation. This comprehensive review examines the potential of green systems—specifically green walls, active green walls, and urban greenery systems—to mitigate atmospheric pollutants such as particulate matter (PM), volatile organic compounds (VOCs), and carbon dioxide (CO2). By systematically analyzing 44 recent studies, the review highlights the pollutant capture efficiency of various green technologies and plant species in both indoor and outdoor settings. Active green walls, particularly those utilizing plant species such as Chlorophytum comosum and Sansevieria trifasciata, were found to be highly effective, with VOC reduction efficiencies up to 96.34%, PM reductions by 65.42%, and CO2 reduction rates reaching 4.8% under optimal conditions. The review identifies key strengths in current research, including diverse experimental setups and the use of sophisticated measurement techniques, but also notes significant limitations such as variability in experimental conditions and a lack of long-term performance data. The study underscores the importance of proper maintenance to sustain green systems' efficacy and highlights the potential issue of pollutant resuspension, which remains under-researched. Practical implications for urban planning are discussed, advocating for the integration of effective green systems into urban infrastructure to enhance air quality and public health. Recommendations for future research include the need for standardized metrics, long-term studies, economic feasibility analyses, and real-world validation of simulation models to better understand and optimize green systems for urban air pollution mitigation.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

Image fusion is a useful tool for producing a high-resolution multispectral image to be used for land use and land cover mapping. In this study, we use nine pansharpening algorithms namely Color Normalized (CN), Gram-Schmidt (GS), Hyperspherical Color Space (HCS), High Pass Filter (HPF), Nearest-Neighbor Diffusion (NND), Principal Component Analysis (PCA), Resolution Merge (RM), Stationary Wavelet Transform (SWT), and Wavelet Resolution Merge (WRM) to fusion Worldview-3 multispectral Bands and panchromatic band. In spectral and spatial fidelity, several image quality metrics are used to evaluate the performance of pansharpening algorithms. The SWT and PCA algorithms showed better results compared to other pansharpening algorithms while GS and CN algorithms showed the worst results for the original image fusion. The effect of fusion on each band was separately investigated and according to the calculations, we found that the CoastalBlue band and the Blue band showed the best result and the NIR-1 band and NIR-2 band show the worst result for the original image fusion. In the end, we conclude that the choice of fusion method depends on the requirement of remote sensing application.

The key goal of the current study was to determine suitable areas of water pumping for drinking and agricultural harvest in Tabriz aquifer, located in East Azerbaijan province, northwest Iran. In the study area, groundwater is the key foundation of water for drinking and farming requirements. Groundwater compatibility study was conducted by analyzing Electrical conductivity (EC), Total dissolved solids (TDS), Chloride (Cl), Calcium (Ca), Magnesium (Mg), Sodium (Na), Potassium (K), Sulfate (SO4), Total hardness (TH), Bicarbonate (HCO3), pH, carbonate (CO3) and Sodium Adsorption Ratio (SAR) obtained from 39 wells in the period of 2003 to 2014. For this purpose, the Water Quality Index (WQI) and irrigation water quality (IWQ) index were utilized. The WQI index zoning exposed that the groundwater of the study area for drinking purposes is categorized as excellent, good and poor water. Most drinking water harvested for urban and rural areas are in the class of 'excellent water'. The results revealed that about 37 percent (296 km2) of groundwater has high compatibility, and 63 percent of the study area (495 km2) has average compatibility for agricultural purposes. The trend of IWQ and WQI indexes demonstrates that the groundwater is getting worse over the time.

The article "Ensuring Quality Medicine is Not a Single Event but a Combined Effort of a Pharmaceutical Company" explores the multifaceted approach required to maintain high standards in pharmaceutical manufacturing. It emphasizes that quality assurance in medicine production is not an isolated event but a continuous, integrated process involving multiple departments and stages. The article highlights the roles of research and development, rigorous clinical trials, regulatory compliance, and robust manufacturing practices in ensuring the efficacy and safety of medicines. It also discusses the importance of quality control measures, such as stringent testing protocols and regular audits, to detect and mitigate potential issues early. The collaboration between different teams within a pharmaceutical company, including scientists, engineers, and quality assurance professionals, is crucial for sustaining quality throughout the product lifecycle. Moreover, the article addresses the necessity of adhering to global standards and guidelines, such as Good Manufacturing Practices (GMP), to ensure consistency and reliability in drug production. By fostering a culture of continuous improvement and vigilance, pharmaceutical companies can effectively safeguard public health and maintain trust in their products. This holistic approach underscores that delivering quality medicine is an ongoing commitment requiring coordinated efforts across the entire organization.

With an increased interest in applications that require a clean background image, such as video surveillance, object tracking, street view imaging and location-based services on web-based maps, multiple algorithms have been developed to reconstruct a background image from cluttered scenes. Traditionally, statistical measures and existing image quality techniques have been applied for evaluating the quality of the reconstructed background images. Though these quality assessment methods have been widely used in the past, their performance in evaluating the perceived quality of the reconstructed background image has not been verified. In this work, we discuss the shortcomings in existing metrics and propose a full reference Reconstructed Background image Quality Index (RBQI) that combines color and structural information at multiple scales using a probability summation model to predict the perceived quality in the reconstructed background image given a reference image. To compare the performance of the proposed quality index with existing image quality assessment measures, we construct two different datasets consisting of reconstructed background images and corresponding subjective scores. The quality assessment measures are evaluated by correlating their objective scores with human subjective ratings. The correlation results show that the proposed RBQI outperforms all the existing approaches. Additionally, the constructed datasets and the corresponding subjective scores provide a benchmark to evaluate the performance of future metrics that are developed to evaluate the perceived quality of reconstructed background images.

The convective hot air drying technology can cause physicochemical, nutritional, and organoleptic losses in mango (Mangifera indica). Therefore, mango dehydration technologies were compared through a Systematic Literature Review to identify the effects on mango’s physicochemical, nutritional, and organoleptic properties. The bibliographic and theoretical results were analyzed. Of the 76 resulting articles, it was found that the countries with authors who participated most in the scientific production were those related to mango production or importation. Furthermore, the freeze-drying technology allows operating at lower temperatures than convective hot air drying, contributing to the preservation of ascorbic acid, among other compounds. The refractance window has the shortest operation time to obtain moisture values between 10 and 20%. The dehydrated samples using the refractance window are smooth, homogeneous, non-porous, and comparable to the color obtained with freeze-drying, which is acceptable for industrial applications.

A study is made of the progressive ‘decoherence’ of cosmic ray extensive air shower particle detector signals in small air showers through measurements of coincidence rates for pairs of detectors versus the detector separation. Measurements are made both when only the two separated detectors themselves trigger in coincidence, and when that coincidence trigger also requires the detection of a local air shower by a small external air shower array. The addition of the explicit air shower trigger ensures that the latter data correspond to showers of a larger particle size, and triggering by very localised shower cores is then unlikely. When including a shower trigger, the decoherence results appear substantially different in form. The coincidence rate between two detectors only can be approximated by a power law variation with separation distance. When triggering involves an air shower array, the variation becomes close to an exponential form with characteristic exponent distances varying systematically with increasing detector and air shower size thresholds. A result is that one can see that small air showers will exhibit clear non-Poissonian density fluctuations near their cores out to distances of ~5m, or at shower energies below ~0.05 PeV. These ideas can be helpful in understanding the statistical properties of signals when using large detectors in air shower arrays.

Fungi are ubiquitous and metabolically versatile. Their dispersion has important scientific, environmental, health, and economic implications. They can be dispersed through the air by the aerosolization of near surfaces or transported from distant sources. Here, we tested the contribution of local (scale of meters) versus regional (kilometers) sources by analyzing airborne fungal community by ITS sequencing around a copper mine in the North of Chile. The mine was the regional source, whereas soil and vegetal detritus were the local sources at each point. The airborne community was highly homogeneous in ca. 2,000 km2, impeding the detection of regional or local contributions. Ascomycota was the dominant phylum in the three communities. Soil and vegetal detritus communities had lower alpha-diversity, but some taxa had abundance patterns related to the distance to the mine and altitude. On the contrary, the air was compositionally even and unrelated to environmental or spatial factors, except for altitude. The presence of plant pathogens in the air suggests that other distant sources contribute to this region's airborne fungal community and reinforces the complexity of tracking the sources of air microbial communities in a real world where several natural and human activities coexist.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: describe briefly the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article, it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

Nowadays, determining the socioeconomic factors' influence on environmental quality is a crucial issue for policymakers. We aim to explore the impact of socioeconomic factors i.e., ethnic conflicts inform ethnic fragmentation, institutions quality effectiveness, and energy consumption on environmental quality by testing the various hypotheses (Pollution Halo Hypothesis, IPAT, and EKC) in 40 selected Asian countries throughout 1993-2019. We also use a set of control variables which are gross domestic product per capita, foreign direct investment inflows, and population growth to determine their impact on environmental quality. We use the Panel Quintile Regression Method of 0.25, 0.5, and 0.75 to analyze the results. We find ethnic conflict negatively affects the environmental quality at all quantiles. The institution's variables regulatory quality and rule of law negatively influence the environmental quality. Our result supports Porter's hypothesis because the effect of direct foreign investment on the amount of CO2 emissions is negative and significant at 0.25, 0.5, and 0.75 quantiles which states that foreign direct investment in the host country supports environmental quality. Furthermore, our results support the IPAT hypothesis in selected Asian countries.

The success of a software product depends on several factors. Given that different organizations and institutions use software products, the need to have a quality and desirable software according to the goals and needs of the organization makes measuring the quality of software products an important issue for most organizations and institutions. To be sure of having the right software. It is necessary to use a standard quality model to examine the features and sub-features for a detailed and principled study in the quality discussion. In this study, the quality of Word software was measured. Considering the importance of software quality and to have a good and usable software in terms of quality and measuring the quality of software during the study, experts and skilled in this field were used and the impact of each factor and quality characteristics. It was applied at different levels according to their opinion to make the result of measuring the quality of Word software more accurate and closer to reality. In this research, the quality of the software product is measured based on the fuzzy inference system in ISO standard. According to the results obtained in this study, it is understood that quality is a continuous and hierarchical concept and the quality of each part of the software at any stage of production can lead to high quality products.

A global approach towards quality management highlights the need for constructing a new body of knowledge that views the field of global quality from a systems perspective. Based on the results of field experiments, and in light of the need to develop new global quality management terminology, the current article presents several key concepts in this field, with emphasis on a systems-oriented rationale and perspective. As such, the article is an important stage in building this body of knowledge, and towards the conceptualization of key variables used in global quality management, from a systems approach that interacts with the fields of international management and strategic management.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

The article discusses determinants of living environment in Central and Eastern Europe. As an example, the city of Radzionkow was chosen, with 16 thousand inhabitants, located in the Silesia agglomeration in southern Poland, in the area where hard coal has been mined for almost two hundred years, which largely serves as a source of heating for houses and flats. 360 buildings in 6 groups of 60 buildings were examined in the selected city, which allowed to distinguish 3 different areas in terms of the quality of the living environment depending on the technical condition of buildings, the method of heating and location. To a large extent, determinants are the existing spatial and geophysical conditions of a given location. Many research and reports on the living environment do not take into account the factors mentioned, focusing only on the statistical data of pollution, excluding spatial factors. In the research presented, the author, taking into account location variables, shows differences in the measurements of air pollution in relation to the designated location zones depending on the morphological structure of the building, the degree of its modernization and the types of heating used in buildings.

Background: Recent studies suggest an association between long-term air pollution, diet, and health outcomes, but there are limited studies on how short-term air pollution affects dyslipidemia in particular. We aimed to investigate this association with modified fruit and vegetable consumption.Methods: The Cardiovascular Disease Association Study (CAVAS) included 8,779 participants between 2007 and 2016. Particulate matter (PM_2.5) and nitrogen dioxide (NO₂) levels were estimated using community multiscale air quality models. Short-term air pollution exposure was defined as a moving average over a lag time from “lag 1 days” to “lag 14 days.” Fruit and vegetable intake was categorized into 'total vegetables (TV),’ 'non-salted vegetables (NSV),' 'salted vegetables (SV),' 'fruits (F),' 'non-salted vegetables + fruits (NSVF),' and 'total vegetables + fruits (TVF).' Dyslipidemia was defined by total cholesterol ≥240 mg/dl, LDL cholesterol ≥160 mg/dl, HDL cholesterol <40 mg/dl, serum triglycerides ≥200 mg/dl, or physician-reported dyslipidemia.Results: Higher short-term PM_2.5 concentrations were associated with an increased risk of dyslipidemia (odds ratio (OR) = 1.012, 95% CI: 1.003, 1.020 for a lag of 14 days). High PM_2.5 groups (≥23.3 μg/m³) with a higher TV intake (≥186.1 g/day) were associated with a decreased risk of dyslipidemia (OR = 0.88, 95% CI: 0.78, 0.99). Additionally, high PM_2.5 groups (≥23.3 μg/m³) with a higher intake of SV (≥110.6 g/day) were associated with a decreased risk of dyslipidemia (OR = 0.86, 95% CI: 0.76, 0.97). Conclusion: Our study suggests that vegetable consumption is an important dietary factor for attenuating risk of dyslipidemia associated with short-term air pollution exposure.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

The outbreak of the COVID-19 pandemic has raised concerns about potential environmental factors that could influence the spread and severity of the SARS-CoV-2 virus. Atmospheric pollution, particularly particulate matter (PM), has been suggested as a contributing factor to viral infections and respiratory complications. This two-year observational study aimed to investigate the relation between air pollution and the spread of COVID-19, focusing on PM2.5. Unlike previous studies limited to specific cities or countries, inevitable to use temporal data. Our research analyzed data from various states across the United States, considering both spatial and temporal correlation. The analysis considered the number and geographic distribution of COVID-19 cases along with daily PM2.5 exposure levels, accounting for monthly average PM2.5 exposure, from March 2020 to December 2021. The observed conflicting results of the temporal and spatial correlation present challenges for researchers in understanding the true nature of the relationship between PM2.5 air pollution and COVID-19 cases. The correlation between various factors, such as population density, PM2.5, temperature, and wind speed, and COVID-19 refers to an association or statistical relationship, not causation. Moreover, the intricate interplay of these variables makes it difficult to establish a clear cause-and-effect relationship.

The research considers creating a network of moss-based biotechnological purification filters in the Smart City concept. The extent of absorption of heavy metals and gases by Sphagnopsida moss under different conditions was investigated. The efficiency of air purification with biotechnological filters was also investigated using the example of the city of Almaty, Republic of Kazakhstan, where an excess of the permissible concentration of harmful substances in the air, according to the WHO air quality guidelines, is recorded throughout the year. Data on the level of pollution recorded by sensors located in the biggest Kazakhstani cities from 06/21/2020 to 06/04/2023 were selected as the basis for calculating the efficiency. In total, there are two hundred twenty sensors in 73 settlements of the Republic of Kazakhstan, with 80 such sensors located in the city of Almaty. Since creating a single biotechnological filter is expensive, the task was to calculate the air purification effect in the case of increasing the number of filters placed in polluted areas. As a result, it is shown that ten filters provide an air purification efficiency of 0.77%, 100 filters 5.72%, and 500 filters 23.11%. A biotechnological filter for air purification based on moss was designed at Astana IT University, considering the climatic features, distribution, and types of pollution in the Republic of Kazakhstan. The obtained results are essential for ensuring compliance with the ISO 37120:2018 standard for environmental comfort in the Republic of Kazakhstan. Additionally, the research findings and the experience of implementing a moss-based biotechnological filter can be applied to designing similar air purification systems in other cities. This is of great importance for the advancement of the field of urban science.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

Rationale: The possible effect of Particulate Matter (PM10 and PM2.5 of diameter 10 and 2.5 µm respectively) levels on Covid-19 mortality is now well established. However, time-evolution of Covid-19 mortality according to PM2.5 levels has been scarcely investigated. Aim: To understand this relationship at the European level for the period 2020 (beginning) - 2022 (end). Methods: 16 representative locations in Europe (81 million people) with heterogeneous levels of PM2.5 (µg.m-3), from low to high. PM2.5 levels were assessed by various methods, and Covid-19 mortality was reported by Johns Hopkins University. Results: The trend of Covid-19 mortality vs. PM2.5 levels varied among locations. Overall, the estimated mean value was of a 40±20% mortality increase per 1 µg.m-3 PM2.5 increase. The stronger the positive gradient of the PM peak, the stronger the positive gradient of the Covid-19 mortality. Exposure to several PM peaks during about a 2-month period was the main contributor to Covid-19 mortality increases. Conclusion: Our data confirm a temporal relation between PM2.5 exposure and Covid-19 mortality, considering a 2-month integration-time for pollution events. Number-concentrations of PM should be used in the future rather than the PM2.5 mass-concentrations (µg.m-3) with the consideration of PM composition to better explain this finding.

Exposure to air pollution have detrimental effects on the elderly, women, people with pre-existing medical conditions, people living in poverty and children. The aim of the study was to investigate the extent of community awareness and knowledge on the health risks associated with exposure to air pollution. A cross-sectional study design was used for the study, using self-administered questionnaires. A simple random sampling technique was used to select 376 respondents. Systematic sampling method was applied to select the households. SPSS version 26 was used to analyze data. Of 376 respondents, 221 were males and 154 females. 113 were aged between 23-47years and 353 were aware that if they don’t protect themselves against polluted air, they may get sick, with age and educational status associated with their awareness (p &lt; 0.05). About 361 knew what air pollution is and 188 think the air they breathe in Annadale is moderate. A total number of 278 said they feel sick/uncomfortable when the quality of air is bad. About 293 knew that people are exposed to air pollution by breathing contaminated air and 237 identified sewage smell as the main cause of air pollution. Respondents who identified internet and television as the main source of information were 199 and 177 respectively. Those who were not aware of actions implemented to reduce air pollution were 180. Based on the results of the study, respondents are aware of the dangers of exposure to polluted air, and it is necessary that air pollution risk communication strategies be implemented to empower residents.

Hot air frying is a new method of frying food, where the use of a small amount of oil is optional but recommended. The objective of this review was to know the state of the art of hot air frying technology, focusing on trends, and thus obtain new ideas for future work in this area of food. In conclusion, the availability of advanced devices will increase the demand for hot air fryers as demonstrated by the trend generating a great economic and social impact. This new technology not only provides health benefits, but also has environmental advantages. In addition, work focusing on food (i.e. tortilla chips, plantain chips, eggs and meats) is recommended, since there are not enough studies on the subject. Currently, research is being conducted on home fryers, so the use of fryers and their impact at the industrial level is a developing area that will require further research.

This document serves as supplemental information to Shapero et al. (2023), which is itself a comment on Nowell et al. (2022). Environmental Health Perspective’s publishing standards for article comments have strict word counts and do not allow the addition of new primary data analyses; therefore, this document provides an additional level of detail and supporting analyses that serve as an important backup to and expansion of Shapero et al. (2023) and that also respond to some comments within the author’s reply to our comments (Holmes and Nowell, 2023). Nowell et al. (2022) evaluated potential PM_2.5 community impacts from sugarcane harvesting. However, their analysis is flawed by erroneous assumptions and misapplied technical approaches, as discussed in Shapero et al. (2023) and as detailed in this supplemental information document. Additionally, the authors ended their analysis with 2018 data, but later data shows no marginal increase in PM_2.5 during sugarcane harvest following 2019 even using the authors’ approach (Holmes and Nowell, 2023). Therefore, the authors’ evaluations have no relevance to current conditions. Nonetheless, even their evaluation and conclusions regarding PM_2.5 concentrations purportedly attributable to sugarcane harvesting prior to 2019 are unsupported and technically unsound as detailed below.

The climate change impacts on some regions of the planet faster and stronger. These areas are known as the hot spots for climate change and Cyprus (Nicosia) in the Mediterranean is one of these spots. This paper aims to analyze the significant changes of atmospheric aerosol characteristics in 2019 and during the extreme event of 25 April 2019. We study the aerosol optical thickness (AOT), Ångström exponent, single scattering albedo, refractive index (imaginary and real parts), size, and vertical distribution of aerosol particles during the event of a high atmospheric aerosol contamination over Nicosia in details. For this purpose, we used the ground-based lidar, observations of the sun-photometer AERONET Nicosia station, satellite products from the Moderate Resolution Imaging Spectroradiometer (MODIS), and back trajectories of air movements calculated using the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT). On 23–25 April, according to lidar and sun-photometer observations, strong aerosol pollution over Nicosia was detected. On April 25, 2019, the AOT value exceeds 1.0 at λ = 440 nm. Analysis of the optical and microphysical characteristics supported that the pollution consists of mainly Saharan dust and partly urban aerosols. This assumption was confirmed by HYSPLIT backward trajectories and MODIS images where air masses containing dust particles came from North Africa and from the Eastern part of Europe.

Air pollution is a serious global issue, responsible for approximately one in every nine deaths each year, ranking it among the greatest environmental hazards to human health. It is of particular concern in urban areas, where elevated pollutant concentrations and potential sufferers converge. Over one half of the world’s population presently lives in urban areas, and the urban population ratio is expected to reach 68% by 2050. Common air pollutants include particulate matter (PM), sulphur dioxide (SO2), ground-level ozone (O3), nitrogen oxide (NOx) and carbon monoxide (CO). While elevated rates of air pollution pose serious health risks for humans, outdoor plants can help reduce the harmful effects of air pollution by filtering and purifying the air around us.In this project Common Ivy, Aster and Miniature Andromeda plants were evaluated for air pollutant mitigation. In this study we developed a vegetation barrier model with the plant located in the middle of the greenhouse box, and air pollutant was sprayed on one side of the plant. Dispersion patterns of sprayed pollutants were tested with and without vegetation barrier. Measurements of carbon dioxide (CO2), Formaldehyde (HCHO), Total Volatile Organic Compounds (TVOC), and Particulate Matter (PM2.5/PM10) were taken before spraying, then at 0 and 30 minutes after spraying, using both monitors.The results show mitigation rates (in 177 ft3 of air after 30 min): for TVOC the minimum reduction is 5 mg/m3; for HCHO, 1 mg/m3; for CO2, 2000 ppm; for PM2.5, 2000 ug/m3; and for PM10 it was 1000 ug/m3.

The mass composition of Particulate Matter (PM) with an aerodynamic diameter of 2.5 microns (PM2.5) in San Joaquin Valley (SJV) is dominated by ammonium nitrate (NH4NO3) which is a secondary pollutant. The goal of this research was the investigation of the relationship between emissions, meteorology and PM2.5 concentrations in Fresno for the winter season. It was found that the location of sites near emission sources such as freeways compared with residential sites strongly affected measured PM2.5 concentrations. It was found that although long-term trends showed declines in both emissions and PM2.5 concentrations there was substantial variability between the years in the PM2.5/emissions relationship. Much of the yearly variation in the relationship between emissions and PM2.5 concentrations can be attributed to yearly variations in weather, such as atmospheric stability, precipitation frequency and average wind speed. There are moderate correlations between PM2.5 concentrations and temperature differences between nearby surface stations at varying elevations which explains some of the daily and seasonal variation in PM2.5. Occurrence of precipitation was related to low PM¬2.5 although the higher wind speeds and lower atmospheric stability associated with precipitation likely explain some of the low PM2.5 as well as washout of PM.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

The Cosmic-Ray Extremely Distributed Observatory (CREDO) is a project dedicated to global studies of extremely extended cosmic-ray phenomena, the cosmic-ray ensembles (CRE), beyond the capabilities of existing detectors and observatories. Up to date cosmic-ray research has been focused on detecting single air showers, while the search for ensembles of cosmic-rays, which may overspread a significant fraction of the Earth, is a scientific terra incognita. Instead of developing and commissioning a completely new global detector infrastructure, CREDO proposes approaching the global cosmic-ray analysis objectives with all types of available detectors, from professional to pocket size, merged into a worldwide network. With such a network it is possible to search for evidences of correlated cosmic-ray ensembles. One of the observables that can be investigated in CREDO is a number of spatially isolated events collected in a small time window which could shed light on fundamental physics issues. The CREDO mission and strategy requires active engagement of a large number of participants, also non-experts, who will contribute to the project by using common electronic devices (e.g. smartphones). In this note the status and perspectives of the project is presented.

Livestock farming is a major source of greenhouse gas and ammonia emissions. In this study, we estimate methane, nitrous oxide and ammonia emission from livestock sector in the Red River Delta region from 2000 to 2015 and projection to 2030 using IPCC 2006 methodologies with the integration of local emission factors and provincial statistic livestock database. Methane, nitrous oxide and ammonia emissions in 2030 are estimated at 132 kt, 8.3 kt and 34.2 kt, respectively. Total global warming potential is 9.7 MtCO_2eq in 2030, accounts for 33% greenhouse gas emissions from livestock in Vietnam. Pig farming is responsible for half of both greenhouse gases and ammonia emissions in the studied region. Other major livestock for greenhouse gas emission is cattle and for ammonia emission is poultry. Hanoi contributes for the largest emissions in the region in 2015 but will be caught up and surpassed by other provinces in 2030.

Air pollution has become a growing invisible killer in recent years and is major cause of morbidity and mortality globally. India stands 10th among the highly polluted countries with an average PM10 level of 134μg/m3 per year. It is also reported that 99% of India's population comes across air pollution level that exceed the World Health Organization Air Quality Guideline (AQG), PM2.5 permissible levels of 10 μg/m3. Maternal exposure to air pollution has a serious health outcome to the offspring because it can affect embryonic phases of development during the gestation period. Fetus is more prone to air pollution effect during embryonic developmental phases due to oxidative stress as antioxidant mechanisms are lacking at that stage. Any injury during this vulnerable period (embryonic phase) will have long-term impact on offspring health both in early and later in life. Epidemiological studies have revealed that maternal exposure to air pollution increases the risk of developing airways disease in offspring due to impaired lung development in utero. In this review, we discuss cellular mechanisms involved in maternal exposure to air pollution and how it can impact development of airways disease in offspring. Better understanding of these mechanisms in context of maternal exposure to air pollution can offer newer avenue to prevent development of airways disease in offspring.

Abstract: Air-polishing with low abrasiveness powders is fats arising as a valid and mini-invasive instrument for the management of biofilm colonizing dental implants. The reported advantage is the efficient removal of plaque with respect of the titanium integrity. In the present study, we evaluated the in-situ plaque-removal and continual the post-treatment anti-bacterial efficacy of an innovative erythritol/chlorhexidine air-polishing powder and compared it with sodium bicarbonate. Two peri-implantitis-linked biofilm formers strains Staphylococcus aureus and Aggregatibacter actinomycetemcomitans were selected and used to infect titanium disks before and after the air-polishing treatment. Cells number and viability were assayed by colonies forming units (CFUs) count and metabolic-colorimetric (2,3-Bis-(2-Methoxy-4-Nitro-5-Sulfophenyl)-2H-Tetrazolium-5-Carboxanilide) (XTT) assay. Air-polishing performed with either sodium bicarbonate or erythritol/chlorhexidine was effective in reducing bacteria biofilm viability and number onto pre-infected specimens, while erythritol/ chlorhexidine showed a higher post-treatment biofilm re-growth inhibition. Surface analysis via mechanical profilometry failed to show an increase in titanium roughness, regardless of the powder selected.

Estimating the infection risks in indoor environments comprises the assessment of the behavior of virus-laden aerosols, i.e. spreading, mixing, removal by air purifiers etc. A promising experimental approach is based on using non-hazardous surrogate aerosols of similar size, e.g. salt particles, to mimic the virus aerosol behavior. This manuscript addresses the issue how a successful transfer of such experiments can be accomplished. Corresponding experiments in two very different environments, a large community hall and a seminar room, with optional use of air purifiers in various constellations were conducted. While high particle concentrations are advantageous in terms of avoiding influence of background aerosol concentrations, it is shown that appropriate consideration of aggregation and settling are vital to theoretically describe the experimentally determined course of particle concentrations. A corresponding model equation for a well-mixed situation is derived and the required parameters are thoroughly determined in separate experiments independently. It is demonstrated that clean air delivery rates (CADR) of air purifiers determined with this approach may differ substantially from common approaches not explicitly taking into account aggregation.

Background Main treatment modality for spinal meningiomas (SM) is gross total resection (GTR). However, optimal timing of surgery, especially in cases with absent or mild neurological symptoms remains unclear. The aim of this study is to assess the impact of early-stage resection on neurological outcome, quality of life (QoL) and quality of care. The primary objective was a favorable neurological outcome (McCormick scale 1); Methods: We retrospectively analyzed data from patients operated on SM between 2011 and 2021. Patients with mild neurological symptoms preoperatively (McCormick scale 1 and 2) were compared to those with more severe neurological symptoms (McCormick scale 3-5). Disabilities and QoL were assessed according to validated questionnaires (SF36, ODI, NDI). Results: Age, spinal cord edema, thoracic localization, and spinal canal occupancy ratio were associated with more severe neurological symptoms (all p<.05). Patients presented with mild symptoms were associated with favorable neurological outcome (OR: 14.778 (95%CI 3.918-55.746, p<.001), which is associated with shorter hospitalization, better QoL and less disabilities (p<.05). Quality of care was comparable in both cohorts; Conclusions: Early surgical intervention of SM, before the development of severe neurological deficits, should be considered as it is associated with a favorable neurological outcome and quality of life.

Maize silage is produced to alleviate forage shortage on dairy animals, particularly during the dry season. Microorganisms play a significant role in silage fermentation and thus determine the silage quality. Therefore, modulation of microorganisms in silage may help prohibit undesired bacteria and improve silage quality. Hence, this study evaluated the effects of tannin extract as an additive on fermentative quality, aerobic stability and microbial composition of maize silage. Therefore, a mini-silo experiment of maize with five treatments was conducted for 75 days. The results showed that additives modulate silage microorganisms. In addition, tannin extract reduced certain silage bacteria while promoting others. However, this is without affecting the silage’s fermentative quality and aerobic stability. All silage fermented well with a pH below 4.2. Tannin extract improved dry matter recovery of silage while reducing silage weight loss. Furthermore, tannin extract suppressed the establishment of undesired bacteria, such as genera Dysgonomonas, Gluconacetobacter and Clostridium, while promoting desirable bacteria, such as genera Lactobacillus and Weissella, which attributed to silage quality. Therefore, it is concluded that tannins can be strategically used as silage additives to modulate microbial composition of silage and improve silage quality by promoting the dominance of desirable bacteria in silage.

Sachet water (SW) is a major source of drinking water in most Nigerian homes, thus making it a possible conveyance medium for health risks due to contamination rather than for replenishment of the body. This study collected SW from three busy neighborhoods and investigated for the presence of indicator bacteria – Escherichia coli (E. coli), Total Coliform (TC), Total Heterophilic Bacteria (THB), and Staphylococcus – and some physio-chemical parameters – total dissolved solids (TDS), pH, electrical conductivity (EC), and salinity. Multi-variable and exploratory statistical methods were applied to the results to determine correlations between bacterial contamination levels and perceived brand reputation. Bacteriological test with raw SW samples appeared too numerous to count (TNC) and thus required serial dilutions. After seven dilutions, results obtained revealed that SW brands with good reputation had no TC and E. coli and was statistically significant with groupings of other SW brands (χ2 = 12.28; p < 0.05 and χ2 = 37.96; p < 0.05) respectively. Additionally, SW brands with poor reputation had mean values of TC (19.7X10^8 cfu/ml;14X10^8 cfu/ml1.15X10^8 cfu/ml) and E.coli (18.2X10^8 cfu/ml;38.7X10^8 cfu/ml,32.4X10^8 cfu/ml) exceeding threshold value of zero set by the World Health Organization (WHO). Only one sample from poor reputation brand tested positive for Staphylococcus and was not statistically significant (χ2 =5.2191; p = 0.074). Principal Component Analysis (PCA)/ Factor Analysis (FA) revealed that most of the SW had fecal contamination in an alarming magnitude. Therefore, this study suggests that periodic cleaning of distribution lines, location specific treatment, QC and QA measures should be taken to reduce water security risk for SW consumption in the region.

Resistance spot welding is an established joining process in the production of safety-relevant components in the automotive industry. Therefore, a consecutive process monitoring is essential to meet the high-quality requirements. Artificial neural networks can be used to evaluate the process parameters and signals to ensure the individual spot weld quality. The predictive accuracy of such algorithms depends on the provided training data set and the prediction of untrained data is challenging. The aim of this paper is to investigate the extrapolation capability of the multi-layer perceptron model. That means, that the predictive performance of the model will be tested with data that clearly differs from the training data in terms of material and coating composition. Therefore, three multi-layer perceptron regression models were implemented to predict the nugget diameter from process data. The three models were able to predict the trained datasets very well. The models, which were provided with features from the dynamic resistance curve predicted the new dataset better than the model with only process parameters. This study shows the beneficial influence of the process signals on the predictive accuracy and robustness of artificial neural network algorithms. Especially, when predicting a data set from outside of the training space.

Asphalt binder requires more investigation to be accurately and precisely extracted since it is a significant procedure for quality control quality assurance (QC/QA) and subsequent binder characterization. In this research, the authors provided a hands-on experience with binder extraction to deliver recommendations concerning the sensitive steps that may affect the outcomes (extracted binder content, P_be%). Based on the extraction by the centrifuge method, two mineral matter determination methods (ashing and centrifuge) were addressed. Field cores were investigated with comparing the P_be% to the actual binder content, P_ba%. Analysis of variance (ANOVA) and Tukey Post-Hoc statistical analyses, in addition to linear least square regression analysis, were used to show the significance of difference according to 38 variant cores randomly obtained from the field segments (in-service roads) via the first two weeks from the construction date. Such cores involved reclaimed asphalt pavement (RAP), reclaimed asphalt shingles (RAS), and a wide range of additives. The two extraction methods were compared with concluding that the centrifuge method was highly recommended based on a quantitative evaluation, which delivered the same average P_ba% based on the 38 cores. Furthermore, the centrifuge method provided much saving in the experimental time (almost half the time required for the ashing method). It was found that the ashing outcomes were equal to the centrifuge outcomes with disregarding the ammonium carbonate addition. Thus, it could be recommended to reassess the ammonium carbonate addition as it might excessively compensate for fake minerals that have not been lost by the ignition oven.

: Following the phenomenal growth of and competition among coffee chain retailers, the coffee chain market has expanded substantially thanks to rising income levels, the increasing young population, and rapidly changing lifestyles. Attracting consumers’ attention and enhancing their loyalty behaviors have become very difficult for coffee chain retailers. This study seeks to understand the mechanisms through which emotions and the dedication-constraint model lead to brand loyalty and willingness to pay more to certain coffee chain retailers. Emotions and the dedication-constraint model are major factors in the research, but few studies have combined them to examine the formation of loyalty behaviors. This study synthesizes emotional responses and the dedication-constraint model to develop a theoretical model. Based on the ambivalent view of emotions, it also examines how positive and negative emotions affect the combination of brand loyalty and willingness to pay more to certain coffee chain retailers. Moreover, it identifies the antecedents of affective and calculative commitments in the context of coffee chain retailers. Our findings indicate that loyalty behaviors (dedication- and constraint-based mechanisms from brand loyalty and willingness to pay more to certain coffee chain retailers), emotional responses, and affective and calculative commitments significantly affect brand loyalty directly and indirectly through both positive and negative emotions. Furthermore, service quality, physical environment quality, and price fairness significantly affect affective commitments, while price fairness significantly affects both affective and calculative commitments. Finally, affective and calculative commitments significantly affect willingness to pay more, both directly and indirectly, through positive emotions and affect it directly through negative emotions. The results’ theoretical and managerial implications and possible future research directions are discussed.

One of the challenges of deploying Wireless Sensor Networks (WSN) at large scale is to operate for prolonged periods of time relying on the limited amounts of energy stored in its nodes. Generally, data communication is the main factor of draining energy. Consequently, reducing the amount of transmitted data by the nodes is of great interest. At the same time, reducing data to be transmitted should not decrease the quality of the deduced information. Solving this problematic is what we call in this article "Ensuring the Quality of Information Service (QoIS)". This document provides a state-of-the-art for the QoIS regarding WSNs. At first, we give a quick overview of the Internet of Things (IoT) paradigm and the WSN technologies in order to understand how data is gathered and used in these networks. Also, we introduce a novel concept: QoIS, in contrast with classic QoS. Then, it is expected a summary of criteria that asses the QoIS in WSNs plus some techniques to improve it. In this article, we will focus on data management techniques. These techniques can improve raw data, information and/or knowledge quality in energy-constrained WSNs. Finally, we give some conclusions and a glimpse about our future work.

An increasingly frail population in nursing homes accentuates the need for high quality care at the end of life and better access to palliative care in this context. Implementation of palliative care and its outcomes can be monitored by using quality indicators. Therefore, we developed a quality indicator set for palliative care in nursing homes and a tailored measurement procedure using a mixed-methods design. We developed the instrument in three phases: 1) literature search, 2) interviews with experts and 3) indicator and measurement selection by expert consensus (RAND/UCLA). Second, we pilot tested and evaluated the instrument in nine nursing homes in Flanders, Belgium. After identifying 26 indicators in the literature and expert interviews, 19 of them were selected through expert consensus. Setting-specific themes were advance care planning, autonomy and communication with family. The quantitative and qualitative analyses showed the indicators were measurable, had good preliminary face validity and discriminative power and were considered useful in terms of quality monitoring according to the caregivers. The quality indicators can be used in a large implementation study and process evaluation in order to achieve continuous monitoring of the access to palliative care for all residents in nursing homes.

In addition to the traditional QoS metrics of delay, delay jitter, and packet loss probability (PLP), Quality of Experience (QoE) is now widely accepted as a numerical proxy for actual user experience. The literature has reported many mathematical mappings between QoE and QoS. These QoS parameters are measured by the network providers using sampling. There are some papers studying sampling errors in QoS measurements; however there is no account of propagation of these sampling errors to QoE evaluation. In this paper, we used industrially acquired measurements of PLP and jitter to evaluate the sampling errors and correlation in measurements. Focussing on Video-on-demand (VoD) applications, we use subjective testing and regression to map QoE metrics onto PLP and jitter. The resulting mathematical functions of QoE and theory of error propagation was used to evaluate the propagated error in QoE, and this error was represented as confidence interval. Using the guidelines of UK government for sampling, our results indicate that confidence intervals around estimated QoE in a busy hour can be between MOS=1 to MOS=5 at targeted operating point of QoS parameters. These results are a new perspective on QoE evaluation, and are of great significance to all organisations that need to estimate the QoE VoD applications precisely.

Groundwater represents a pivotal asset in conserving natural water reservoirs for potable consumption, irrigation, and diverse industrial uses. Nevertheless, human activities intertwined with industry and agriculture contribute significantly to groundwater contamination, highlighting the critical necessity to appraise water quality for safe drinking and effective irrigation. This research primarily focused on employing the Water Quality Index (WQI) to gauge water's appropriateness for these purposes. However, the generation of an accurate WQI can prove time-intensive owing to potential errors in sub-index calculations. In response to this challenge, an artificial intelligence (AI) forecasting model was devised, aiming to streamline the process while mitigating errors. The study collected 422 data samples from Mirpurkash, a city nestled in the province of Sindh, for a comprehensive exploration of the region's WQI attributes. Furthermore, the study probed into unraveling the interdependencies amidst variables in the physiochemical analysis of water. Diverse machine learning classifiers were employed for WQI prediction, with findings revealing that random forest and gradient boosting eclipsed other algorithms, achieving an accuracy rate of 99%. In close pursuit were SVM and XGBoost, registering accuracy scores of approximately 95% and 93%, respectively, while KNN and Decision Trees garnered accuracy rates of 88% and 87%, respectively. In addition to WQI prediction, the study conducted an uncertainty analysis of the models using the R-factor, providing insights into the reliability and consistency of predictions. This dual approach, combining accurate WQI prediction with uncertainty assessment, contributes to a more comprehensive understanding of water quality in Mirpurkash and enhances the reliability of decision-making processes related to groundwater utilization

Study Objectives: To (1) investigate the prevalence of sleep disorder symptoms in caregivers of children with autism spectrum disorder (ASD) and (2) the relationships between caregiver sleep problems and their health-related quality of life and family quality of life. Methods: Descriptive cross-sectional study of caregivers (N=62) of children ages 6 to 11 years old diagnosed with ASD receiving care at a regional autism research and resource center. Measurements and Results: Participants completed the Sleep Habits Questionnaire (SHQ), the Medical Outcomes Study (MOS) SF-12, and the Beach Center Family Quality of Life Scale (FQOL). Caregivers with longer sleep duration reported better mental health and better family quality of life. Caregivers who reported insomnia symptoms, non-restorative sleep, and insufficient sleep were more likely to report poorer mental health than caregivers who did not report these sleep disorder symptoms. Caregivers with obstructive sleep apnea and restless legs syndrome experienced worse physical quality of life. Conclusions: The physical and mental health of the primary caregiver is essential to the support of the child with ASD and to the functioning of the family. The study findings point to the importance of future research and interventions to enhance sleep health in order to improve quality of life for caregivers of children with ASD.

Computer systems are involved in many critical human applications today, so that a small error can lead to serious and dangerous problems. These errors can be from an error in the incorrect design of the user interface to an error in the program code. The success of a software product depends on several factors. Given that different organizations and institutions use software products, the need to have a quality and desirable Software according to the goals and needs of the organization makes measuring the quality of software products. an important issue for most organizations and institutions, To be sure of having the right software. It is necessary to use a standard quality model to examine the features and sub-features for a detailed and principled study in the quality discussion. In this study, the quality of Word software was measured by Adaptive Neural Fuzzy Inference System. In recent years, powerful systems called fuzzy inference systems on The basis of adaptive neural network (ANFIS) has been used in various sciences. Using the power of neural network training and the linguistic advantage of fuzzy systems, these types of systems have been able to realize the advantages of the two in terms of analyzing very powerful complex processes. Considering the importance of software quality and to have a good and usable software in terms of quality and measuring the quality of software during the study. It was applied at different levels to make the result of measuring the quality of Word software more accurate and closer to reality. In this research, the quality of the software product is measured based on the adaptive neural-fuzzy inference system in ISO standard. According to the results obtained in this study, it is understood that quality is a continuous and hierarchical concept and the quality of each part of the software at any stage of production can lead to high quality products.

The tiered laboratory framework for HIV viral load monitoring accommodates a range of HIV viral load testing platforms, with quality assessment critical to ensure quality patient testing. HIV plasma viral load testing is challenged by the instability of viral RNA. An approach using an RNA stabilizing buffer is described for the Xpert® HIV-1 Viral Load (Cepheid) assay and was tested in remote laboratories in South Africa. EDTA-plasma panels with known HIV viral titres were prepared in PrimeStore molecular transport medium for per-module verification and per-instrument external quality assessment. The panels were transported at ambient temperatures to 13 testing laboratories during 2017 and 2018, tested according to standard procedures and uploaded to a web portal for analysis. A total of 275 quality assessment specimens (57 verification panels and two EQA cycles) were tested. All participating laboratories met study verification criteria (n=171 specimens) with an overall concordance correlation coefficient (ρ_c) of 0.997 (95% confidence interval [CI]: 0.996 to 0.998) and a mean bias of -0.019 log cp/mL (95% CI: -0.044 to 0.063). The overall EQA ρ_c (n=104 specimens) was 0.999 (95% CI: 0.998 to 0.999), with a mean bias of 0.03 log cp/mL (95% CI: 0.02 to 0.05). These panels are suitable for use in quality monitoring of Xpert® HIV-1 VL and are applicable to laboratories in remote settings.

Groundwater is a vital resource for human welfare. However, due to various factors, groundwater pollution is one of the main environmental concerns facing. Yet, it is challenging to simulate groundwater quality dynamics due to the insufficient representation of nutrient percolation processes in the soil and Water Assessment Tool model. The objectives of this study were extending the SWAT module to predict groundwater quality. The results proved a linear relationship between observed and calculated groundwater quality considering No3 and TDS with R2, NSE and PBIAS values in the satisfied ranges, albeit underestimation and overestimation were observed due to limited data availability. These results highlight that nitrate and TDS concentrations and variability in groundwater may used as a tool in surface water quality that have to be assumed for designing adaptive management scenarios. Hence, extended SWAT model could be a powerful tool for future regional to global scale modelling of nutrient loads supporting effective surface and groundwater management.

In this article, the quality of water in the reservoirs of Lake Arpi, Lake Yerevan, Akhuryan, Azat, Aparan and Kechut was estimated with usage of the Armenian Water Quality Index. It was established that in the waters of reservoirs the the maximum permissible concentration of copper, vanadium, aluminum, chromium, manganese, iron, NH4+ and NO2- regularly increases. The following computational algorithm was used for determination of the Armenian Water Quality Index values: to determine the number of cases of MPC excess of i-substance or indicator of water –n; to estimate the total amount of cases of the maximum permissible concentration (N) – N = ∑n; to computes log2N, nlog2n and ∑nlog2n; to determine geoecological syntropy (I) and entropy (H): I = ∑ nlog2n/N and H = log2N – I. Then, Geo-Ecological Evolving Organized index index was determined: G = H/I. Further, the total amount multiplicity of MAC exceedances was estimated: (M) - M=∑m and log2M was computed. Finally, Armenian Water Quality Index was obtained: AWQI = G + 0.1log2M. It was established that the Armenian Water Qquality Index showed a linear dependence on the Water Contamination Index, the Specific Combinatory Water Quality Index, the Geo-Ecological Evolving Organized index and an inverse dependence on the Canadian Water Quality Index.

This study examines the potential of UiO-66 and g-C3N4-based composite catalysts for environmental purification and pesticide degradation. By integrating zirconium-based metal-organic framework UiO-66 with graphitic carbon nitride (g-C3N4), a composite with a Z-type heterojunction structure is created, enhancing photocatalytic pesticide degradation and phosphorus recovery. The optimal composite, UiO-66/g-C3N4(UG6:4), shows high efficiency in degrading organophosphorus pesticides like DDVP under visible light. This catalyst's high surface area and porous nature efficiently adsorb and break down persistent soil pollutants, including DDT and DDVP. Featuring robust stability and effective photocatalytic activity, the UiO-66/g-C3N4 composite holds promise for soil remediation and dealing with organic pollutants. Future research will aim to further refine this material’s structure and properties, ensuring its practical application in environmental cleanup.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

DNA extraction for downstream molecular diagnostic applications can be an expensive, time-consuming process. We devised a method to quickly extract genomic DNA from environmental samples based on sodium hydroxide lysis of cells with or without capture by magnetic beads, for subsequent PCR or quantitative PCR. The final DNA extraction method using NaOH is extremely low-cost and can be completed in 10 minutes at room temperature. NaOH extraction was effective for Gram-negative and Gram-positive bacteria in samples from air, soil, sewage, food, laboratory surfaces, and chicken cloacal swabs. The NaOH extraction method was comparable to commercial kits for extraction of DNA from pig fecal samples for 16S amplicon sequencing analyses. We demonstrate that an impinger and portable pump can efficiently capture bacteria in poultry facilities for rapid DNA extraction for quantification of total bacteria and for detection of specific species using qPCR. The air sampling and NaOH extraction procedures are well-suited for routine, high throughput screening, and for metagenomic analyses for specific pathogens, even in resource-limited situations.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.