In this study, we investigated the inhibiting effect of Dioscorea spp leaf extracts on the corrosion of mild steel in selected media using the weight loss method. The mild steel samples were pre-weighed and immersed in NaOH, NaCl and H₂SO₄ solutions respectively containing the leaf extracts, with the control samples immersed in solutions of the media containing no extract. The samples were allowed to stand for 672 hours, with a set of samples from each environment withdrawn at intervals of 168 hours for corrosion characterization. The results obtained from all the environments indicate that the corrosion rate increased as concentrations of Dioscorea spp increased. Results also confirmed that the extract was an effective and excellent inhibitor in the alkaline, salt, and acidic media. Conclusively it was proven that the higher concentration of Dioscorea spp leaf extracts in the media had the best inhibition characteristic on the mild steel in the selected environments. The results show good potential for application in manufacturing industries. The microstructure analysis of the various test coupons in the test media should be carried out to reveal the influence of adding the leaf extracts to the stimulated media on the grain structure distribution of the mild steel.

Activated Corrosion Products (ACPs) formation and deposition pose a critical safety issue for nuclear fusion reactors. The working fluid transports the ACPs towards regions accessible to worker personnel. Predicting ACPs formation deposition and transport is fundamental for source term identification, reduction of radiation exposure assessment, maintenance plan definition, design optimization, and waste management. The code OSCAR-Fusion has been developed by the CEA (France) to evaluate the ACPs generation and transport in closed water-cooled loops for fusion application. This work aims at assessing the impact of water chemistry on the transport, precipitation, and deposition of corrosion products for the EU-DEMO divertor Plasma Facing Unit Primary Heat Transfer System. Sensitivity analyses and uncertainty quantification are needed due to the multi-physics phenomena involved in ACPs formation and transport. The OSCAR-Fusion/RAVEN code coupling developed by the Sapienza University of Rome and ENEA has been used. This work presents the perturbation results of different parameters chosen for a closed water-cooled loop considering a continuous scenario of 1888 days. The aim of this work is to assess the variation of build-up of ACPs, perturbing the alkalizing agent concentration into the coolant and the corrosion and release rates of different materials.

The importance of understanding the corrosion mechanisms of excavated metal artefacts help in determining the physico-chemical parameters of the burial environment and the formation of different corrosion products. These products can be observed and analysed with the help of various techniques that provide information on their morphology, chemical composition and structure. The analysis of ancient coins is extremely challenging in the presence of heavily corroded surfaces; as quantitative information may not exactly concur with its bulk composition. In the case of silver coins, the use of surface information can be used as a guide for bulk composition only. The current study carries out investigation and characterization of selected coins from a large coin hoard excavated from Amheida, Dakhla oasis, Egypt. The study and analysis of the alloy composition and corrosion products was performed using a multi-technique approach which included Light optical microscopes, Scanning Electron microscope (SEM) coupled with energy dispersive spectroscopy (EDS) and X-ray diffraction analysis. Investigation of the coins revealed the presence of a thick active inhomogeneous corrosion crust, while analysis showed that the coins were made from a binary silver copper alloy (billon) while the corrosion crust was rich in chlorides and carbonates, later identified by XRD analysis as Paratacamite, Malachite and Chrysocolla.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

This research evaluates the inhibitory effect of L-amino acids (AAs) with different side chain lengths on Fe surface implementing Monte Carlo (MC) simulation. A quantitative and qualitative description of the adsorption behavior of AAs on the iron surface has been carried out. Calculations have shown that the absolute values of the adsorption energy of L-amino acids increase with side chain prolongation; they are also determined by the presence of heteroatoms. AAs from nonpolar and basic groups have the best adsorption ability to the iron surface, which indicates their highest inhibitory efficiency according to the results of MC simulation.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

Herein, we describe precisely on covalent modification of pure magnesium (Mg) surface and applied to induce in vitro osteogenic differentiation. A new concept, chemical bonding method is proposed for developing stable chemical bonds on Mg surface through serial assembly of bioactive additives including ascorbic acid (AA) and bovine serum albumin (BSA). The coating with such potential materials shows strong integrity to the Mg and could suitable for cell-interface interaction with the host tissue during implantation in bone tissue repair. The physicochemical and electrochemical properties of surface modified Mg assess how these nanoscales layered of biomolecules could demonstrate the significance improvement in chemical stability of coating. The modified Mg-OH-AA-BSA exhibits better anti-corrosion behavior with high corrosion potential (Ecorr ~ ‒ 0.96 V) and low corrosion current density (Icorr ~ 0.2 µA cm-2) as compared to pure Mg (Ecorr ~ ‒1.46 V, Icorr ~ 10.42 µA cm-2). Outer layer of BSA on Mg protects fast degradation rate of Mg which is the consequence of strong chemicals bonds between amine groups on BSA with carboxylic groups on AA. Collectively, the results suggest that surface modified Mg provides strong bio-interface and enhances the proliferation and differentiation of pre-osteoblast (MC3T3-E1) cells through protein-lipid interaction. Owing to this fact, the cost-effective and scalable covalent functionalization of Mg surface inherits biological advantage in orthopedic and dental implants with long term stability.

The acoustic emission (AE) technique was applied to monitor the pitting corrosion of carbon steel in NaHCO₃ + NaCl solutions. The open circuit potential (OCP) measurement and the corrosion morphology in-situ capturing using optical microscope were conducted during AE monitoring. The corrosion micromorphology was characterized with scanning electron microscope (SEM). The propagation behavior and AE features of natural pitting on carbon steel were investigated. After the performing of signal processing including pre-treatment, shape preserving interpolation and denoising for raw AE waveforms, three types of AE signals can be classified in the correlation diagrams of new waveform parameters. Finally, a 2D pattern recognition method was established to calculate the similarity of different continuous AE graphics, which is quite effective to distinguish the localized corrosion from uniform corrosion.

The inhibition impacts of 1,10-Phenanthroline-5,6-diamine (PTDA) on mild steel in 1 M HCl solution were investigated through weight loss method. The inhibition efficiencies of PTDA increase with increase in PTDA concentration at the temperature 303. Weight loss method indicate that PTDA is an excellent inhibitor the inhibition efficiency of 81.5% at the maximum PTDA concentration of 0.5 g/L at the temperature 303K.

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

This study focuses on the increased risk of high heat release and asphyxiation (toxic gas poisoning) in the event of a fire of polyurethane (PU) and MDF-based building materials, which are commonly used in building fires. Among them, polyurethane (PU) building materials are essential for buildings except in Europe and some other countries due to their excellent thermal insulation performance, but problems of short-term heat release and spread of toxic gases in the event of a fire continue to occur. To overcome these problems, researchers are actively working on introducing various flame retardants into building materials. Therefore, in this study, we produced a laboratory-sized (500mm*500mm) plate flame retardant board that can be utilized as a building material with a lower heat release rate and a lower toxicity index by mixing expanded graphite and ceramic binder as flame retardants in a main material based on the cellulose of waste paper by replacing the existing building materials with a hot-press method. According to the ISO-5660-1 test on the heat release rate of the plate flame retardant board, the THR value was 2.9 (MJ/m2) for 10 minutes, showing an effect of reducing the THR value by 36.3 (MJ/m2) compared to the THR value of 39.2 (MJ/m2) of the specimen made using only paper. In addition, the toxicity index of the flame retardant board was checked through the NES 713 test. As a result, the test specimen showed a toxicity index of 0.7, which is 2.4 lower than the toxicity index of 3.1 of MDF, which is utilized as a conventional building material. Based on the results of this study, the cellulose fire retardant board showed the effect of reducing the heat release rate and toxicity index of building materials in a building fire, which reduces the risk of rapid heat spread and smoke toxicity. This has the potential to improve the evacuation time (A-SET) of evacuees in fires. It is also important to show that recycling waste paper and utilizing it as the main material for building materials can be an alternative in terms of sustainable development.

This article reports on the comparative study of the hot deformation behaviour of virgin (steel A) and rejuvenated heat treatment creep-exhausted (steel B) P91 steels. Hot uniaxial compression tests were conducted on the two steels at the deformation temperature range of 900°C-1050°C and a strain rate range of 0.01-10s-1 to 0.6 strain using Gleeble® 3500 equipment. The results showed that the flow stress largely depends on the deformation conditions. The flow stress for the two steels increased with an increase in strain rate at a given deformation temperature and vice versa. The flow stress-strain curves exhibited a dynamic recovery as the softening mechanism. The material constants determined using Arrhenius constitutive equations were: stress exponent was: steel A (5.76) and steel B (6.67), and the apparent activation energy was: steel A (473.1 kJ mol-1) and steel B (564.5 kJmol-1). From these results, steel A exhibited better workability than steel B. Statistical parameters analyses showed that the flow stress for the two steels had a good correlation between the experimental and predicted data. Pearson’s correlation coefficient (R) was: steel A (0.97) and steel B (0.98). The Average Absolute Relative Error (AARE) values were: 7.62% (steel A) and 6.54% (steel B). The study shows that the Arrhenius equations can effectively describe the flow stress behaviour of P91 steel, and this method is applicable to the industrial metalworking process.

In this paper, in order to provide proper parameters for the preparation of semi-solid billets, the semi-solid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) with X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), scanning transmission electron microscope (STEM). XRD results show that with the increase of temperature, equilibrium θ-Al2Cu gradually dissolved in the matrix. The EDS results of SEM and STEM show that there were coarse θ-Al2Cu phase, ultra-fine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase and atomic clusters in the microstructure. EBSD results show that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), the homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX happened in the semi-solid temperature. In the process of recrystallization, the micro-texture changed from preferred orientation to random orientation. A variety of experimental results show that static recrystallization (SRX) occurred at semi-solid temperature due to the blocking effect of atomic clusters on dislocation slip and the Zener drag effect of fine precipitates on low angle grain boundaries (LAGBs) disappeared with melting at semi-solid temperature.

This paper evaluates an architectural design using an Energy Consumption consideration of Natural Ventilation in a hot dry climate (Khartoum State), at dwellings design applied. Method was used analysis of Autodesk IEVS software natural ventilation and energy consumption simulation. It resulted that to cooling, by natural ventilation in dwelling design used to get indoor temperature at the comfortable level during the summer. The Best-Case Situation of natural ventilation with consider of energy saving Based on the CFD simulation analysis, the performance of internal air velocity is approximately 0.7m/s. The wind velocity starts to slow down towards the rear of the apartment spaces. Approximately 95% of the internal areas have average air velocity between 0.43 m/s to 0.9 m/s. Internal Air flow pattern single floor house plan at Khartoum (Alazhari City); showing the internal air velocity of 0.7m/s near the window opening positions with the wind directions in the details and pressure of the air as worst-case situation, with velocity and temperature of the air with average 22o as a best-case situation. during a year. Architectural design process in the urban area of Alazhari City for dwelling towards to saving energy was applied and determined into an urban planning neighbourhood at Khartoum.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

This paper studied the combined influences of the hot streak and swirl on the cooling performances of the NASA C3X guide vane coated with or without TBCs. The results show that: (1) Even under uniform velocity inlet conditions, the hot streak core can be stretched as it impinges the leading edge which causes higher heat load on the suction side of the forward portion. (2) The swirl significantly affects circumferential and radial migration of the hot streak core in the NGV passage. On the passage inlet plane, positive swirl leads to a hotter tip region on the suction side. In comparison, negative swirl leads to a hotter hub region on the pressure side. (3) Under the influence of swirl, migration of coolant improve the coverage of film cooling close to the midspan, while in the regions close to the hub and tip end-wall, the overall cooling performance decrease simultaneously. (4) In the regions with enough internal cooling, the cooling effectiveness increment is always larger than that in other regions. Besides, the overall cooling effectiveness increment decreases on the region covered by film cooling for the coated vane, especially in the region with negative local heat flux.

One of essential procedure nowadays to analyze a dynamic process in Science and Engineering is Computational modeling. Most of dynamic processes are distributed parameter systems, i.e., systems with state variables depend on the number of independent variables (such as space and time) which are expressed by a set of Partial Differential Equations (PDEs). Lateral method of lines is a method which used for solving PDEs numerically by solving a set of boundary value problems sequentially. The aim is to report the development of PDE toolbox based on SCILAB. This paper provides users with a method that is very easy to understand in the applications related to dynamic process. The method uses a SCILAB template to develop numerical simulations in the new field. In this paper, a model of tropical fruit heat treatment for decimating insect is presented. The illustration will be given to show how the lateral method of line template works to solve the problem.

Cylindrical Fe-6.5wt.% Si bars with 7.5 mm in diameter were successfully fabricated from as cast ingot through three rolling stages within 10 passes: rough rolling at 850–900 °C and 8–10 m/min, medium rolling at 800–850 °C and 10–15 m/min, and finish rolling at 800–850 °C and 12–18 m/min. The evolution of microstructure, texture and ordered structure, and the mechanical property are investigated. The results showed that the grains were refined by the hot bar rolling. Area fractions of the {100}<011> oriented grains and the {011}<100> oriented grains decreased to 0 during the hot bar rolling. Whereas, the {100}<001> component, the {011}<211> component and the {112}<110> component increased, and γ fiber with {111}<110> component was dominant. DO₃ ordered phase were suppressed, and B2 ordered domains were refined after the hot bar rolling. Ductility of the as rolled bar was higher than that of the rotary swaged bar, due to the absence of the DO₃ ordered phase and the fine grains in the rolled bar. Hence, the hot bar rolling technology is an excellent process to fabricate the Fe-6.5wt.% Si bars.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The key question for the understanding of corrosion phenomena of Si3N4-SiC material in Al reduction cell – whether corrosion by gases (and oxidation in particular) opens way for the corrosion by molten cryolite, or corrosion of Si3N4-SiC by cryolite plays its own role in degradation of the material in service. More probably the reactions of silicon carbide and silicon nitride with molten cryolite go after the stage of pre oxidation to silicon dioxide. The corrosion of Si3N4-SiC material in the reduction cell may take place by “gas-solid” reaction and by “liquid-solid” reaction. There are several variants of lab corrosion test for the evaluation of corrosion resistance of Si3N4-SiC material to cryolite. The results of investigation of Si3N4-SiC lab corrosion test give no direct evidence of selective dissolution of specific phase (Si3N4 or SiC, α-Si3N4 or β-Si3N4) in cryolite. The existing variants of lab corrosion testing require clarification.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

it still undergoes corrosion when exposed to corrosive environments. This paper proposes an evaluation method for assessing the corrosion level of SPCC steel specimens using traditional eddy current testing (ECT), along with two different machine learning approaches. The objective is to classify the corroded state of the specimens into two states: a less corroded state (state-1) and a highly corroded state (state-2). Generative and discriminative models were implemented for classification. The generative classifier was based on the Gaussian mixture model (GMM), while the discriminative model was based on the logistic regression model. The models used features based on the absolute maximum of the perturbation magnetic field components at two different frequencies. The performance of the classifiers was evaluated using metrics such as absolute error, accuracy, precision, recall, and F1 score. The results indicate that high classification accuracy can be achieved based on both methods using traditional eddy current testing.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

Magnesium alloy stents have been extensively studied in the field of biodegradable metal stents due to their exceptional biocompatibility, biodegradability and excellent biomechanical properties. Nevertheless, the specific in vivo service environment causes magnesium alloy stents to degrade rapidly and fail to provide sufficient support for certain time. This paper presents an overview of the development history and protection strategies for magnesium alloy stents. Alloying, optimizing stent structure and preparing protective coating have improved the corrosion resistance of magnesium alloy stents. Based on the corrosion mechanism of magnesium alloy stents, as well as their deformation during use and environmental characteristics, we present some novel solution strategies aiming at reducing the corrosion rate of magnesium alloys and enhancing the comprehensive performance of magnesium alloy stents. These strategies include adapting protective coatings for the deformation of the stents, preparing rapid endothelialization coatings to enhance the service environment of the stent, and constructing coatings with self-healing functions. It is hoped that this review can help to understand the development of magnesium alloy cardiovascular stents and solve the problems related to magnesium alloy stents in clinical applications at the early implantation stage.

The effects of organic metabolites produced by a sulfate-reducing prokaryote (SRP) in seawater on the anode corrosion process of magnesium alloy were analyzed by open circuit potential, electrochemical impedance spectroscopy, polarization curve, and other electrochemical methods, combined with scanning electron microscopy and X-ray diffraction. It was found that the product film produced by magnesium alloy anode corrosion was not dense, and the surface of the magnesium anode substrate was exposed during the corrosion process. The corrosion of magnesium anode matrix was accelerated by the simulation of different organic metabolites including mannose, glucuronic acid, and glucose. Thus, the synergistic effect of various metabolites produced by SRP in the corrosion process of magnesium alloy may be considered in future studies.

Wirobond C is a commercial dental casting alloy suitable for the fabrication of crowns, bridges as well as metal-ceramic restorations. This work aims with the study of the effect of ready-to-use Listerine® and Meridol® mouthwashes and sodium fluoride on corrosion resistance of the CoCrMo dental alloy to electrochemical corrosion in artificial saliva at 37 °C. SEM, EDS, SKP, and microhardness investigations were carried out to characterize the material under study. In vitro corrosion resistance of the CoCrMo alloy was conducted by the open circuit potential method, electrochemical impedance spectroscopy, and anodic polarization curves. The presence of Co 59.8(8) wt.%, Cr 31.5(4) wt.%, and Mo 8.8(6) wt.% was confirmed. The CoCrMo alloy was characterized by Vickers microhardness of 445(31) µHV0.3. Based on EIS data, the capacitive behavior and high corrosion resistance of CoCrMo alloy was revealed. The kinetics of pitting corrosion in the artificial saliva was lower after the modification with NaF and Listerine and Meridol mouthwashes. The potentiodynamic characteristics revealed the passive behavior of CoCrMo alloy in all solutions. Based on the SKP measurements of the CoCrMo alloy after corrosion tests, the effect of artificial saliva modification on electronic properties of Bego Wirobond C dental alloy was found.

Tungsten carbide inserts (TCI) and polycrystalline diamond compact (PCD) cutters used in two types of drill bits for drilling oil and gas wells were evaluated by a pin-on-disc test. The morphology of the worn surface was characterized by scanning electron microscopy (SEM). The behavior of corrosion resistance was evaluated with the electrodynamic polarization technique. The polycrystalline diamond compact cutter has a higher hardness, better corrosion, and wear behavior compared to tungsten carbide.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

On-stream inspections are the most appropriate method for routine inspections during plant operation without going through production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52°C. This study aims to determine the ultrasonic velocity and attenuation with the known material grade, thickness, and temperatures by comparing theory calculation versus experiment with temperatures ranging between 30°C to 250°C on low carbon steel covering most petrochemical equipment material and working conditions. The theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the predicted results of ultrasonic change due to temperature increase and showed a maximum error of 3%. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that require a quick corrosion status determination.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

Selection of efficient corrosion inhibitors requires detailed knowledge regarding interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. Position of functional groups between different isomers is often overlooked but not less important since factors like steric hinderance may significantly affect the adsorption mechanism. In this study we have presented how different dihydroxybenzene isomers interact with aluminium alloy 5754 surface, reducing its corrosion rate in bicarbonate buffer (pH = 11). We have shown the highest inhibition efficiency among tested compounds belongs to catechol at 10 mM concentration, although differences were moderate. Utilization of novel impedance approach to adsorption isotherm determination allowed to confirm that while resorcinol chemisorbs on aluminium surface, catechol and quinol follows ligand exchange model of adsorption. Unlike catechol and quinol, the protection mechanism of resorcinol is bound to interaction with insoluble aluminium corrosion products layer and was only found efficient at concentration of 100 mM (98.7%). The aforementioned studies were confirmed with scanning electron microscopy and x-ray photoelectron spectroscopy analyses. There is a significant increase of the corrosion resistance offered by catechol at 10 mM after 24 h exposure in electrolyte: from 63 to 98%, with only negligible changes in inhibitor efficiency observed for resorcinol at the same time. However, in the case of resorcinol a change in electrolyte color was observed. We have revealed that the differentiating factor is the keto-enol tautomerism. The NMR studies of resorcinol indicate the keto form in structure in presence of NaOH, while the chemical structure of catechol does not change significantly in alkaline environment.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

Medical implants made of biodegradable materials could be of advantage for temporary applications such mechanical support during bone-healing or as vascular stents to keep blood vessels open. After completion of the healing process the implant would disappear, avoiding long-term side effects or the need for surgical removal. Various corrodible metal alloys based on magnesium, iron or zinc have been proposed as sturdier and potentially less inflammatory alternative to degradable organic polymers, in particular for load-bearing applications. Despite the recent introduction of magnesium-based screws the remaining hurdles to routine clinical applications are still challenging, such as limiting mechanical material characteristics or unsuitable corrosion characteristics. Here, salient features and clinical prospects of currently investigated biodegradable implant materials are summarized with a main focus on magnesium alloys. A mechanism of action for the stimulation of bone growth due to the exertion of mechanical force by magnesium corrosion products is discussed. To explain divergent in vitro and in vivo effects of magnesium a novel model for bacterial biofilm infections is proposed which predicts crucial consequences antibacterial implant strategies.

Our study aims to implement a strategy to reduce the carbon steel corrosion rate in sulfuric acid solution, using an expired drug with adsorption affinity on the metal surface. To investigate the corrosion protection efficiency of an environmental friendly inhibitor, namely neomycin sulfate (NMS), the electrochemical measurements were applied on carbon steel immersed in 1.0 M H₂SO₄ solution with and without NMS. The protective layer formed on the steel surface was studied by atomic force microscopy (AFM). The potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) showed that the presence of the neomycin sulfate in acid solution leads to the decrease in corrosion current density (i_corr) and the increase of polarization resistance (R_p). The mixed mechanism between physical and chemical adsorption of NMS molecules on the steel surface was proposed according to the Langmuir adsorption isotherm. The Atomic Force Microscopy (AFM) indicated that the NMS molecules contributed to a protective layer formation by their adsorption on the steel surface. The AFM parameters such as: root-mean-square roughness (R_q); average roughness (R_a) and maximum peak to valley height (R_p-v) revealed that in the presence of NMS a smoother surface of carbon steel was obtained, compared to the steel surface corroded in sulfuric acid blank solution.

This paper investigates the evolution of microstructures and precipitations of an ultra-low iron alloy 625 subjected to long term aging treatment by scanning electron microscope (SEM) and X-ray diffraction(XRD). Use ASTM G28A acid Fe3(SO4)2 erosion to represent intergranular corrosion weightlessness and corrosive morphology. The result shows that alloy at 750C by aging treatment for 40h, precipitated γ'' phase in the grain boundary. In high density area of γ'' phase, occurs γ'' phase to δ phase degeneration transformation by aging treatment for 200h and the needle-like δ phase becomes more with time prolonged. And γ'' phase degenerated to δ phase completely until treated for 1000h. The sample which has aging treatment tends to have intergranular corrosion and mainly because alloy element spreading leads to dilution area and grain boundary precipitated phase, plus interlaced δ phase’s dissolving, which makes sample grain particle fall off and this results in apparent weightlessness. The weightlessness rate(WLR) is related with precipitated volume score. With aging sensitization time change, can be described by Johnson-Mehl-Avrami equation, i.e.: $WLR=44.32\left[1-\text{exp}\left(-\frac{t}{10.99}\right)\right]+44.62\left[1-\text{exp}\left(-\frac{t}{327.8}\right)\right]+1.267\left(mm/a\right)$

Commercial production of Choromytilus meridionalis (black mussel) and Mytilus galloprovincialis (Mediterranean mussel) contributes to half of the South African marine aquaculture production per year. However, limited ready-to-eat black mussel products are available. The aim of this preliminary study was to investigate the effects of storage (15 days at room temperature) on the total viable counts (TVC), coliforms, proximate composition, and fat oxidation (TBARS) of a small-scale kitchen-based ready-to-eat hot smoked black mussel product preserved with vegetable oil. Three batches of black mussel meat were smoked at 80ºC for 15 minutes. Half of each batch were packaged in sterile glass jars with heated (50ºC) vegetable oil and half without oil. Microbiological analyses were done at days 1, 3, 9 and 15. Proximate composition was determined at day 1 and TBARS at days 1 and 15. Coliforms for all samples throughout the storage period were undetected. TVC plates for mussels stored without oil had no growth at days 1 to 5, however, reached TVC > 5 log10.g-1 at day 15. TVC for mussels with oil increased from 0 at day 1 to > 5 log10.g-1 at day 3 and remained at counts > 5 log10.g-1. There was no significant difference (P > 0.05) in moisture, protein, and ash for mussels stored with oil and those without oil, while significant differences (P < 0.001) in total fat and carbohydrates (10.27 ± 2.10% and 6.80 ± 2.22% with oil, and 5.05 ± 1.49% and 10.59 ± 3.00% without oil) were detected. These differences were due to the presence of additional fats from the vegetable oil. TBARS at day 15 showed no significant difference (P > 0.05) between mussels stored with oil and those without oil. There were no significant differences in TBARS from day 1 to 15 for both oil and without oil. Small-scale kitchen-based smoked black mussels preserved without vegetable oil could be stored for up to 9 days at room temperature.

One of the main factors that influence the fertility of cattle in grazing systems in hot tropical climates is heat stress. The objective of this study was to evaluate the effect of season, breed, hormonal and physiological condition on the quantity and quality of cumulus-oocyte complexes (COCs) and embryos produced in vitro, from Romosinuano (RM) and Tropical Milking (TM) donors. Three ovum pick-up and in vitro fertilization (OPU-IVF) were performed, one per season; hot dry (HD; 10, 10), hot humid (HH; 9, 9) and fresh dry (FD; 7, 10) in RM and LT donors. Serum levels of cortisol, insulin and glucose were measured, in addition to heart rate (HR), respiratory rate (RR) and rectal temperature (RT). Effect of season x genotype interaction (p≤0.05) was observed in all COCs variables and only in cleavage embryos (CLI) (p≤0.05). Body weight (BW) affected all COCs variables (p≤0.01), except unviable (UNV) although affected degenerated embryos (DEG) (p≤0.01) and total blastocysts (BLAST) (p≤0.01). Cow age only affected viable COCs (VIAB) (p ≤ 0.05), code one blastocysts (BC1) and BLAST (p≤0.01). Cortisol affected total COCs (COCsT), VIAB and total matured in vitro (TMIV) (p≤0.01), as well as CLI, BC1 (p≤0.01) and BLAST (p≤0.05). Insulin affected COCsT (p≤0.01), UNV (p≤0.05), denuded oocytes (DE) (p≤0.01), BC1 and code two blastocysts (BC2) (p≤0.01). Glucose affected all COCs variables (p≤0.01), except UNV and all embryo variables except BC2. HR affected COCsT, DE, TMIV (p≤0.01), CLI, BLAST and DEG (p≤0.05). RR affected COCsT, UNV, VIAB, CLI (p≤0.05), BC1, BLAST and DEG (p≤0.01). RT only affected DE, VIAB (p≤0.01) and BLAST (p≤0.05). The seasonal climatic year variation of Veracruz and changes in physiological and hormonal variables have diverse effects on the cumulus-oocyte complexes and embryos produced by RM and TM donors.

In this study, the effect of laser processing (LP) on the thermoelectric (TE) properties of bismuth antimony telluride (BST) alloy pellets is investigated. The stoichiometric alloy used is Bi0.4Sb1.6Te3.0, which was prepared by mechanical alloying techniques (MA) and hot pressed (HP) into pellets under optimal pressing and temperature conditions. An innovative approach to HP was also developed to enhance the yield of BST samples per HP process while maintaining the TE profiles of the samples within a variance of less than 1%. The LP process was executed by employing a metal 3D printer, with a thorough analysis of beam parameters. Notably, the laser power (P) was held constant at 25 W, along with a fixed hatching distance (HD) of 50 μm, while the parameter adjusted was the laser's scanning speed (SS), which spanned from [600 - 1800] mm/s in increments of 200 mm/s. Examination via scanning electron microscopy (SEM) revealed two material states: melted and sintered. The melted state formed the surface crust of "canyon" patterns that were held on the surface of the samples, and which both size and quantity were altered with changes in SS. For thermoelectric characterization, two distinct shapes of LP samples were produced: rectangular (for electrical properties) and disk (for thermal properties). The results demonstrated that the electrical properties are profoundly influenced by SS, with the electrical conductivity peak at SS value of 1600 mm/s, while the Seebeck coefficient reaches a minimum at the same value. Consequently, within the temperature range of interest, a notable 12% increase in electrical conductivity and a 9% decrease in the Seebeck coefficient were observed compared to the non-LP material state. Overall, the ZT value experience an 6.9% decline within the same temperature interval.

Since decades, oxybutynin hydrochloride is prescribed to improve bladder control in cases of incontinence and excessive urination frequency. This review summarizes synthetic methods enabling preparation of the racemic drug and, in a detailed manner, preparation of (S)-2-cyclohexyl-2-hydroxy-2-phenylacetic acid, a key intermediate in the synthesis of (S)-oxybutynin. Mode of action and metabolism are briefly commented in order to explain the main adverse effects associated with its use and to justify the evolution observed in the diverse commercial formulations. Repositioning opportunities are discussed in terms of clinical trials for the management of hyperhidrosis, hot flashes, and obstructive sleep apnea.

Cancer is considered nowadays one of the main causes of human death worldwide, being characterized by an alteration of the oxidative metabolism. Many natural compounds with anti-tumor attributes have been described, many of them from plant origin. Among them, capsaicin, which is the molecule responsible for the pungency in hot pepper fruits, has been reported to show antioxidant, anti-inflammatory and analgesic activities, as well as anti-proliferative properties against cancer. Thus, in this work the potential anti-proliferative activity of pepper (Capsicum annuum L.) fruits from diverse varieties with different capsaicin content (California < Piquillo < Padrón < Alegría riojana) against several tumor cell lines (lung, melanoma, hepatoma, colon, breast, pancreas, and prostate) has been investigated. The results showed that the capsaicin content in pepper fruits did not correspond with their anti-proliferative activity against tumor cell lines. By contrast, the greatest activity was promoted by the pepper tissues which contained the lowest capsaicin amount. This indicates that other compounds different from capsaicin have this anti-tumor potentiality in pepper fruits. Based on this, green fruits from the variety Alegría riojana, which has negligible capsaicin levels, was used to study the effect on the oxidative and redox metabolism of tumor cell lines from liver (Hep-G2) and pancreas (MIA PaCa-2). Different parameters from both lines treated with pepper fruit crude extracts were determined including, among others, protein nitration and protein S-nitrosation (two post-translational modifications (PTMs) promoted by nitric oxide), the antioxidant capacity, as well as the activity of the antioxidant enzymes superoxide dismutase (SOD), catalase, and glutathione peroxidase (GPX). Besides, the activity of the NADPH-generating enzymes glucose-6-phosphate dehydrogenase (G6PDH), 6-phosphogluconate dehydrogenase (6PGDH), and NADP-isocitrate dehydrogenase (NADP-ICDH) was followed. Our data revealed that the treatment of both cell lines with pepper fruit extracts altered their antioxidant capacity, enhanced the catalase activity, and considerably reduced the activity of the NADPH-generating enzymes. As a consequence, less H2O2 and NADPH seem to be available to cells, thus avoiding cell proliferation and possibly triggering cell death in both cell lines.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

In the present study Aprepitant (APT) ternary solid dispersions (SDs) were developed and evaluated for the first time. Specifically, ternary SDs of APT with Poloxamer 188 and Soluplus^® (SOL) were prepared via melt mixing and compared to binary APT/Poloxamer 188 and APT/SOL SDs. Initially, combined thermo-gravimetric and hot-stage polarized light microscopy studies indicated that all tested compounds were thermally stable up to 280 °C, while Poloxamer 188 acted as a plasticizer to SOL by significantly reducing the temperature required to fully solubilize the API during SD preparation. Differential scanning calorimetry combined with wide angle X-ray diffraction studies showed that crystalline API was dispersed in both binary and ternary SDs, while Fourier transformation-infrared spectroscopy studies revealed no molecular interactions among the components. Scanning electron microscopy combined with EDAX element analysis showed that the API was dispersed in nano-scale within the polymer matrices, while increasing APT content led to increasing API nano-crystals within the SDs. Finally, dissolution studies showed that the prepared formulations enhanced dissolution of Aprepitant and its mechanism analysis was further studied. A mathematical model was also investigated to evaluate the drug release mechanism

The flow behavior of Fe-6.5wt.%Si alloys during hot compression was investigated at temperatures 650–950 °C and strain rates 0.01–10 s^-1. The results showed that the flow stress depended distinctly on the deformation temperatures and strain rates. The flow stress and work hardening rate increased with the decrease of temperature and the increase of strain rate. The activation energy under all the deformation conditions was calculated to be 410 kJ/mol. The constitutive equation with hyperbolic sine function and Zener–Hollomon parameter was developed. The peak stress, critical stress, and steady-state stress could be represented as σ=A+Bln(Z/A). Dynamic recrystallization occurred under the deformation conditions where the values of Z were lower than 10²⁰. Processing maps were established to optimize the processing parameters. The power dissipation efficiency decreased in the high temperature and low strain rate region, increased in the high temperature and high strain rate region, and remained unchanged in other regions with the increase of true strain. Furthermore, the unstable area expanded. The true strain of 0.7 was the optimum reduction according to the processing map. Based on the analysis of surface quality, microstructures, and ordered structures, the optimized processing parameters for the Fe-6.5wt.%Si alloys were the temperature and strain rate of higher than 900 °C and 0.01–10 s^-1, respectively, or 800–900 °C and lower than 0.4 s^-1, respectively.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

This research aims to explore the use of sodium benzoate C6H5-COOH as corrosion inhibitor added to the mixing water of concrete, and test the mechanical performances of five types of concretes over several time periods, 7, 28, 56 and 90 days, in the absence and in the presence of limestone fillers. Hence the results confirm the increase in this resistance over time. Through this, tests were carried out cement paste after addition of sodium benzoate and limestone fillers, we see clearly that the start and the and setting time of cement shift out considerably which indicates that sodium benzoate aims to delay start and end setting time of cement. In addition, Abrams cone slump tests on concrete in the fresh state were carried out in order to see the influence of the addition of sodium benzoate and tests on the cement consistencies in the absence and presence of superplasticizing adjuvant “ORAFLOW THM 17200” which has the main role of improving the workability and quality of the concrete while comparing with ordinary concrete.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Modern engineering faces challenges in ensuring technical standards for service, durability, and sustainability. Political, administrative, and budgetary factors, coupled with climate change, pose tasks to structural integrity, affecting industries and economies. Marine infrastructures represent a strategic asset of the country as it handles a large part of the economic exchanges. This article analyzes five essential factors that play a fundamental role in the performance analysis of coastal structures: Chloride-induced corrosion, degradation models, maintenance strategies, monitoring, and climate change. Starting with reinforcement corrosion, considered as the main cause of distress, particularly in coastal zones for the long-term behavior of structures. Additional pressure from the influences of climate change is becoming evident and extreme, leading to reduction in capacity. To guarantee the lifespan, degradation models contribute by estimating the long-term performance of the asset as a strategic piece to the development of effective maintenance solutions. Additionally, quantifying the condition of the structure from monitoring data, plays a crucial part that provides information on the current situation of the structure. Finally, this review summarizes the challenges associated with the maintenance of aging marine structures considering aspects such as corrosion, monitoring, and the future challenges this area will face due to climate change.

Chemical and mechanical properties of plasma-assisted nitrided (PAN), TiN cathodic arc coated, and PAN with TiN coated samples were thoroughly evaluated on tool steel samples of 1.2379. The evaluation involved SEM, nano-indentation, profilometer, micro scratch, and corrosion tests. The results revealed that PAN treatment alters the roughness of the surface, while it has minimal impact on the coefficient of friction. However, it increases the substrate's hardness, making it twice as hard and three times more resilient against scratch tests, along with improved corrosion resistance. TiN-coated samples are four times harder than untreated ones, but they exhibit a higher elastic modulus (E), leading to a lower H/E index. The most promising results were obtained with PAN+TiN treatment, combining high hardness (H) with lower E, resulting in a high H/E index, a crucial criterion for wear resistance. These samples also demonstrated superior scratch hardness and corrosion resistance, despite being thinner and rougher.

This paper investigates the effect of shot peening on the strength and corrosion properties of EN AW 6082-T651 aluminium alloy. Surface roughness, microhardness, residual stresses and corrosion performance were investigated and compared with the untreated aluminium alloy. Cracks and delaminations in the surface layer can only be seen on the treated specimens at a working pressure of 4 bar and 8 bar, while no such effect was observed at a working pressure of 1.6 bar. The effect of dislocation densification was confirmed by the microhardness measurement of the hardened layer, where microhardness increased by up to 23 % compared to the untreated aluminium alloy. Shot peening also results in a deeper layer with higher compressive residual stresses compared to untreated specimens. With higher working pressure, surface roughness increases, which can promote localized pitting corrosion. However, all treated specimens improve the corrosion resistance and have a lower degree of anodic dissolution. The current density of the shot peened specimen with the lowest surface roughness was more than twice lower than that of the untreated specimen.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

The control of air quality in museums or storages is of fundamental interest for the conservation of historic artifacts. The present work reports an example of application of RFID sensors developed in the European project SensMat and dedicated to this issue. The sensors are based on the varia-tion of property of an RFID tag coupled to a sensitive silver thin film exposed to the environment. As it will be described in the paper, such low cost sensors are interrogated by a commercial reader and provide the environmental corrosivity index and thus the presence of pollutants. The selected case study concerns the monitoring of pollution by H2S in a building dedicated to conservation and restoration of archeological and historical woods. The ability of sensors to map spatially the corrosivity within buildings is highlighted.

Background: Nowadays investigations in the field of dental implants engineering are focused on bioactivity and osseointegration properties.Objective: In this study, the oxide-covered titanium was functionalized by vitamin D3 molecules via a simple self-assembly method with the aim to design more corrosion resistant and at the same time more bioactive surface.Methods: Surface properties of the D3-coated titanium were examined by scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurements, while a long-term corrosion stability during immersion in an artificial saliva solution was investigated in situ by electrochemical impedance spectroscopy.Results: Results of all techniques confirmed a successful formation of the D3 vitamin layer on the oxide-covered titanium. Besides very good corrosion resistivity (~5 MΩcm² ) the D3-modified titanium surface induced spontaneous formation of biocompatible bone-like calcium phosphates (CaP).Conclusion: Observed in vitro CaP-forming ability as a result of D3-modified titanium/artificial saliva interactions could serve as a promising predictor of in vivo bioactivity of implant materials.

The present work shows a novel physical-mathematical model to estimate the average corrosion resistance index from the crystallographic texture in API 5L steels. The crystallographic texture of the studied steels was measured by means of the X-ray diffraction technique. The model, based on the symmetric spherical surface harmonics for a BCC structure, is capable of describing the anisotropy surface of anodic dissolution resistance of the crystal and establishing a straightforward relationship between crystallographic texture, surface roughness, and metal corrosion behavior. The predictions of the average corrosion resistance index made from the crystallographic texture were in good agreement with those obtained from potentiodynamic polarization curves for the investigated steels. This agreement validates the capacity of this model and opens the possibility of applying it as a novel criterion for the material selection and design stages in order to combat metal corrosion problems.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

Artificial intelligence methods, especially artificial neural networks (ANNs), have increasingly been utilized for the mathematical description of physical phenomena in (metallic) material processing. Traditional methods often fall short in explaining the complex, real-world data ob-served in production. While ANN models, typically functioning as "black boxes," improve pro-duction efficiency, a deeper understanding of the phenomena, akin to that provided by explicit mathematical formulas, could enhance this efficiency further. This article proposes a general framework that leverages (CAE) ANNs to explain predicted results alongside their graphical presentation, marking a significant improvement over previous approaches and those relied on expert assessments. Unlike existing Explainable AI (XAI) methods, the proposed framework mimics the standard scientific methodology, utilizing minimal parameters for the mathematical representation of physical phenomena and their derivatives. Additionally, it analyzes the relia-bility and accuracy of the predictions using well-known statistical metrics, transitioning from deterministic to probabilistic descriptions for better handling of real-world phenomena. The proposed approach addresses both aleatory and epistemic uncertainties inherent in the data. The concept is demonstrated through the hot extrusion of aluminum alloy 6082, where CAE ANN models and predicts key parameters, and ChatGPT explains the results, enabling researchers and/or engineers to better understand the phenomena and outcomes obtained by ANNs.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Hypertension (HTN) is the foremost contributor to cardiovascular diseases (CVD), which remain a leading cause of death. However, adherence to the properly prescribed dosage form is critical and challenging for patients with chronic diseases such as HTN to prevent illness progression and death. The study’s objective was to develop AMB-loaded subcutaneous implants to reduce the frequency of administration, thus improving patient compliance during HTN management. AMB subcutaneous implants were prepared using continuous hot melt extrusion technology using PCL and PLGA with dimensions of 7.5 cm (length) by 2 mm (diameter). The implants were characterized for thermal characteristics, drug-excipient incompatibilities, surface morphology, fracturability, in vitro release, and stability studies. DSC showed that the drug was in the crystalline state in the fabricated implants. Scanning Electron Microscopy (SEM) revealed a smooth surface. The lead formulation presented good drug content, showed an extended drug release profile over 30 days, and followed zero-order release kinetics with a mean dissolution time of 15 days. The formulation was stable over 30 days in accelerated stability conditions (the last time point was tested, 40℃/75% RH), and the release profile was similar to the initial drug release profile. The lead formulation showed good fracturability during textural analysis. Therefore, the hot melt extruded implants could be an alternative management strategy for conventional amlodipine besylate (AMB) formulation.

The menopausal transition often accompanies distressing manifestations, including vasomotor symptoms, sleep disruptions, and depressive syndrome. Omega-3 fatty acids have emerged as a potential intervention to alleviate these symptoms. This review aimed to comprehensively assess the impact of omega-3 supplementation on vasomotor symptoms, sleep quality, and depression among postmenopausal women. We conducted a systematic search focusing on randomized control trials across the Cochrane Library, Web of Science, PubMed, CINAHL, EMBASE, and SCOPUS databases from inception to August 2023. Among the initial pool of 163 studies, 9 studies met the inclusion criteria and were incorporated into this review. Four studies suggested potential benefits of omega-3 intake for improving hot flashes and night sweats. Sleep quality outcomes displayed heterogeneity across the studies. Incorporating diverse scales such as the Hamilton Depression Rating Scale-21, the Patient Health Questionnaire depression scale, and Generalized Anxiety Disorder-7 for depression outcomes, the review found inconclusive evidence on omega-3's impact on depression. Overall, the combined analysis of these studies did not provide substantial evidence to support the efficacy of omega-3 fatty acids in improving vasomotor symptoms, sleep quality, and depression. Further well-designed RCTs with larger participant groups are crucial to validate and generalize these results.

Objectives: The present study was conducted to evaluate the indicators of the aging-friendly using GIS software in the eight districts of Ahwaz, southwest Iran in 2022. Materials and methods: this descriptive-analytical study was conducted on 317 older adults by stratified random sampling method. Data collection tools were demographic characteristics and aging-friendly city indicators. GIS methods were used for the spatial analysis and SPSS version 28 software was used to analyze descriptive statistics. Results: The mean age of the participants was 66.21±6.99 years. Most of the participants in this study were male (53.9%), illiterate (34.7%), married (84.9%) and residents of district 7 (22.1%). The findings of the present study showed that all 8 districts follow spatial autocorrelation and cluster pattern in all components of the aging-friendly city (urban open spaces, intra-urban transportation system, public and religious places and buildings, safety and ease of traffic, social participation and communication, social respect, culture-recreation, health and treatment). Conclusion: According to the results, the city of Ahwaz is far from the ideal level among the components of an aging-friendly city; therefore, provincial and city officials should pay more attention to these indicators and take more effective steps to increase their quality.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

This paper presents a novel approach of welding thick steel plates that offers time and energy savings compared with conventional techniques. The combination of gas metal arc welding (GMAW) and hot-wire technology simplifies the joint configuration and enhances the process tolerance. In this study, a square butt joint was prepared with as-cut edges and a thickness of 15 mm. The relationship between the welding current and the deposition rate of solo GMAW showed limitations and low process tolerance. Increasing the welding current led to a larger deposited volume with unnecessary weld penetration. An independent deposition volume due to hot-wire insertion was used to improve process tolerance. This approach provided an additional volume without increasing the welding current and reduced unnecessary penetration. With optimized parameters, full-penetration single-pass welding was achieved. Compared with the formation of a typical single-v butt joint at a similar welding speed of 30 cm/min, the proposed process reduced the minimum arc time and power consumption by approximately 83% and 62%, respectively. Moreover, a single pass at a travel speed of 60 cm/min was achieved with approximately 91% and 81% less arc time and power consumption, respectively. In summary, the combined process simplifies the joint configuration, enables full-penetration single-pass welding, and reduces time and energy requirements.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

. In today’s world, cyber attack is one of the major issues concerning the organizations that deal with technologies like cloud computing, big data, IoT etc. In the area of cyber security, intrusion detection system (IDS) plays a crucial role to identify suspicious activities in the network traffic. Over the past few years, a lot of research has been done in this area but in the current scenario, network attacks are diversifying in both volume and variety. In this regard, this research article proposes a novel IDS where a combination of information gain and decision tree algorithm has been used for the purpose of dimension reduction and classification. For experimental purpose the NSL-KDD dataset has been used. Initially out of 41 features present in the dataset only 5 high information gain valued features are selected for classification purpose. The applicability of the selected features are evaluated through various machine learning based algorithms. The experimental result shows that the decision tree based algorithm records highest recognition accuracy among all the classifiers. Based on the initial classification result a novel methodology based on decision tree has been further developed which is capable of identifying multiple attacks by analyzing the packets of various transactions in real time.

This short note proposes a national Geographic Information System (GIS) - based health infrastructure to deal with epidemics and pandemics. Currently, there is no pan-India health infrastructure available that can compile, update, and report the spread of epidemic diseases. It not only curtails the opportunity of finding the real-time data on the spatial distribution of a disease but prevents one to inquire into the causes of the disease through epidemiological analysis. The proposed infrastructure in this study is a pan-India one and can broadly be divided into two parts, hotspot mapping and accessibility to services. In the first part, hospitals are proposed to act as nodes of data collection, sending data to a national GIS portal. This portal shall have the capabilities of plotting the data using map rendering services such as Google and Bing Maps. This way, hotspots can be visualized in no time, benefitting the government and common citizenry alike. The second part deals with the accessibility of citizenry to a wide range of services, i.e., healthcare services, grocery outlets, emergency services, baby food, and many other essential services of the day to day life. In order to implement this, we propose that the government need to enforce a mandatory submission of locational coordinates of all Goods and Services Tax (GST) enrolled service providers. Once the coordinates are submitted, the government can effectively control the opening and closing of services and inform the citizenry at the same time. The proposed infrastructure is going to help deal with the extraordinary situations during epidemic and pandemics similar to what the world is currently facing in the form of Corona Virus Disease 2019 (COVID-19). Furthermore, the infrastructure can be scaled up or down as per the spread of a disease. The health-GIS platform proposed in this concept paper, shall help India in controlling and managing the epidemic more efficiently.

Hot deformation at elevated temperature is essential to densify the particle reinforced Aluminum matrix composites (AMCs) and improve their performance. However, hot deformation behavior of the AMCs is sensitive to the variation of hot processing parameters. In this paper, optimal processing parameters of the dual-scale SiCp/A356 composites was determined to explore the control strategy of the microstructure. Hot compression tests were conducted at the temperature ranging from 460 to 520℃ under strain rates from 0.01 to 5 s−1. Constitutive equation and processing maps were presented to determine the hot processing parameters. Microstructure evolution of the dual-scale SiCp/A356 composites was analyzed. The strain rate of 0.62 ~ 5s-1 and deformation temperature of 495 ~ 518℃ is suitable for the hot processing. The number of DRX grains in the “safe” domains is larger and the dislocation density is lower compared to those of instability domains. DRX particles mainly occurred around SiC particles. The presence of SiC particles can promote effectively the DRX nucleation, which result in that the dynamic softening mechanism of the dual-scale SiCp/A356 composites is dominated DRX.

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

Mere similar grades of same excipients manufactured by two different manufacturers often differ significantly that they even have an impact on the variations in final product or dosage form. Solid lipids are one of the most available options as matrix former in sustained drug delivery. Due to their chemical and physical complexity, lipids may exhibit a complex behaviour (i.e. melting crystallization and polymorphism). The aim of this study was to evaluate the physical and chemical properties of two Glyceryl Monostearate (GMS) lipids (Geleol from Gattefosse and Capmul GMS 50K from Abitec Corp. USA) and how these properties may affect during melt granulation process for sustained release applications. Thermal processing was applied on GMS samples to understand the polymorphic nature and suitability as meltable binders. Niacin was used as model drug. A thorough evaluation of GMS samples and sustained release tablets was undertaken using analytical techniques such as differential scanning calorimetry (DSC), X-ray diffraction (XRD). Moreover, melt viscosity study assisted to apprehend the behaviour of GMS samples in hot melt extrusion processing. Surface morphology of the drug and extruded granules examined via SEM and AFM revealed high level of surface interaction and dense structure of drug inside lipid matrix. The DSC and XRD study confirmed that Geleol could not withstand the heat treatment applied during thecontinuous melt granulation processing. The shifting of stable β form to an unstable α form in Geleol was detected. In the contrary case, Capmul GMS 50K was able to withstand the heat treatment supported by the applied analytical techniques. Nonetheless,both GMS samples perform differently in final dosage form. This change in stable β form to an unstable α form affected dissolution profiles at 3 months storage in accelerated condition. This study helped to interpret the complex solid-state behaviour of solid lipid extrudates with different compositions, in order to the simply and outline a suitable formulation strategy for the development of lipid-based oral dosage forms.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

The current scenario of radioactive waste management requires innovative and automated solutions to ensure effectiveness and safety. In response to this need, the PI3SO (Proximity Imaging System for Sort and Segregate Operations) project was proposed. It is a gamma radiation proximity scanner system for radioactive waste with the primary goal of speeding up some aspects of the waste management cycle while reducing direct human operations. The system will provide proximity imaging for hot spot finding and spectral analysis for radiological characterization, enabling semiautomatic recognition, sorting and separation of radioactive waste. The core of the proposed scanning system consists of an array of 128 CsI(Tl) scintillators, 1 cm3 size, coupled with silicon photomultipliers (SiPM), installed on a motorized bridge sliding along a suitable table in order to scan the materials under investigation.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

Forestry workers play a crucial role in implementing forest management programs, but their outdoor work exposes them to rising temperatures caused by global climate change, which poses potential health risks related to heat. This study focuses on Indonesian forestry workers and examines the relationship between their knowledge of heat-related issues, risk perception, and precautionary behavior in dealing with increasing workplace heat exposure. Developing effective precautionary behavior is essential for preventing heat-related health disorders and promoting health protection programs. To facilitate a comprehensive comparison of the three variables, interviews were conducted with two groups of outdoor workers, comprising 210 forestry workers and 215 paddy farmers. The findings indicate that increasing knowledge about heat-related issues promotes precautionary behavior, and risk perception acts as a mediator between knowledge and behavior. Additionally, the study highlights that the emotion of "dread" intensifies perceived risk and predicts positive behavior change. To enhance heat-related knowledge, exploring the potential use of a "fear" tone is important. In conclusion, comprehensive strategies need to be implemented to promote precautionary behavior among vulnerable forestry workers, particularly manual laborers.

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

Background: The new media provides a convenient digital platform to access, use and exchange health information. As a special group of health care, maternal is still of international concern due to their high mortality rate. Improving maternal health as a Millennium Development Goal of the United Nations is an important quest for the health care system. Scientific research provides advice on how to improve maternal health through stringent reasoning and accurate data. However, the dramatic increase of publications, the diversity of themes, and the dispersion of researchers may reduce efficiency. Objective: This study aims to analyze the research progress on maternal health under the global new media environment, exploring the current research hotspots and research frontiers. Methods: A scientometric analysis was carried out by CiteSpace5.7.R1, searching in the core database of Web of Science for articles published in English from 1998 to 2021, and combined topic words such as new media, maternal, and health. In total, 3312 articles have been retrieved, of which 2270 studies have been included for further analysis. Top countries and institutions, potentially high-impact literature, research frontiers, and hotspots were analyzed in this study. Results: The number of publications grew rapidly after 2008, from 29 publications sharply increasing to 472 publications by 2020. Research centers concentrated in Latin America, such as the University of Toronto, the University of California. The work of Larsson M, Lagan BM, Tiedje L, and Helle C had a high potential impact. Most of the research subjects were maternal and newborn babies, and the research frontiers focused on health education and maternal psychological problems. Maternal mental health, maternal and infant nutrition, weight, production technology, and equipment were hotspots. Conclusion: The development of new media has brought a new era for maternal health, characterized by psychological qualities, healthy and reasonable physical conditions, and advanced technology.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Cyber security plays an important role to protect our computer, network, program and data from unauthorized access. Intrusion detection system (IDS) and intrusion prevention system (IPS) are two main categories of cyber security, designed to identify any suspicious activities present in inbound and outbound network packets and restrict the suspicious incident. Deep neural network plays a significant role in the construction of IDS and IPS. This paper highlights a novel IDS using optimized convolution neural network (CNN-IDS). An optimized CNNIDS model is an improvement over CNN which selects the best weighted model by considering the loss in every epoch. All the experiments have been conducted on the well known NSL-KDD dataset. Information gain has been used for dimensionality reduction. The accuracy of the proposed model is evaluated through optimized CNN for both binary and multiclass categories. Finally, a critical comparison has been performed with other general classifiers like J48, Naive Bayes, NB tree, Random forest, Multilayer Perceptron (MLP), Support Vector Machine (SVM), Recurrent Neural Network (RNN) and Convolution Neural Network(CNN). All the experimental results demonstrate that the optimized CNN-IDS model records the best recognition rate with minimum model construction time.

The spike protein of SARS coronavirus (SARS-CoV) attaches the virus to its cellular receptor, angiotensin-converting enzyme 2 (ACE2), which is mediated by the receptor binding domain (RBD) of the spike protein. Recently, an analysis based on decade-long structural studies of SARS was reported to illustrate with atomic-level details receptor recognition by the novel coronavirus from Wuhan, i.e., 2019-nCoV. Here, this article reports a comprehensive set of structural electrostatic analysis of all SARS-CoV spike protein RBD-related structures as of February 13, 2020, aiming at identifying the electrostatic hot spots for SARS-CoV spike protein to be complexed with ACE2 and its neutralizing antibodies. First, this article identified a structural action mechanism of the F26G19 antibody (of SARS-CoV spike protein), where its Asp56 residue binds to the Arg426 of the SARS-CoV spike protein RBD against the formation of the interfacial Arg426-Glu329 salt bridges between ACE2 and the SARS-CoV spike protein RBD. Second, a hypothesis is reported that a pair of electrostatic clips exist at the interface between ACE2 and the SARS-CoV spike protein RBD, including both Arg426-Glu329 and His445-Glu23-Lys447 salt bridges. Last, this article reports a structurally identified interfacial Glu35-Arg479 salt bridge which helps stabilize the complex structure of ACE2 and the SARS-CoV spike protein RBD. Overall, the structurally identified electrostatic hot spots reported here may be useful for the design of SARS-CoV-neutralizing antibodies in future.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

The application possibilities of austenitic stainless steels in high friction, abrasion and sliding wear conditions are limited by their inadequate hardness and tribological characteristics. In order to improve these properties, thermochemical treatment of their surface by plasma nitriding is suitable. This article is focused on corrosion resistance of the conventionally plasma nitrided AISI 304 stainless steel (530 °C, 24 hours) in 0.05 M and 0.5 M sodium chloride solutions at room temperature (20 ± 3 °C), tested by potentiodynamic polarization and electrochemical impedance spectroscopy. The optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy are used for the nitrided layer characterization. The experiment results point to a significant reduction in corrosion resistance after performed plasma nitriding even in a solution with a very low chloride concentration (0.05 mol/L).