This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Percutaneous coronary intervention (PCI) to chronic total occlusion (CTO) is still a subject of debate. The primary goal of revascularization is to provide symptomatic relief and enhancing left ventricular (LV) functions. Global longitudinal strain (GLS) is proven to be more sensitive than ejection fraction (EF), especially for subtle ischemic changes. The purpose of this study was to investigate the improvement in LV GLS after revascularization of symptomatic stable coronary patients with single-vessel CTO, categorized according to their collateral supply grades. 69 patients with successful CTO PCI were grouped according to their collateral supply grades, as well-developed (WD) and poor collateral groups and followed-up for 3 months. Basal characteristics were similar for both groups, except for lower EF (p=0.04) and impaired GLS (p<0.0001) in the poor collateral group. At the end of 3 months follow-up symptomatic relief was similar in both groups (p=0.101). GLS improvement reached statistical significance only for the poor collateral, not for the WD group (p<0.0001 and p=0.054, respectively). EF did not change significantly in both groups. Poorly collateralized CTO lesion may not only result in baseline LV dysfunction, but also appear to carry potential for recovery after revascularization. This may not be the case for WD collaterals.

During tensile testing of materials, strain measurement is conducted using either contact or non-contact methods. Contact methods offer high accuracy and precision but are limited by the specimen's thickness and dimensions, whereas non-contact methods minimize damage to thin specimens and allow measurements in various environments, though they require longer prep-aration and calculation times. This paper proposes a circular grid marking pattern and a strain prediction algorithm using artificial intelligence (AI), which simplifies the preparation process and allows strain prediction without additional equipment. The circular grid pattern can be ar-ranged in various configurations from 1×5 to 5×7, and a laser marker, which requires minimal time, was used to engrave the pattern on the specimen to shorten the preparation time. The AI model, trained on image-based data, enables strain calculation regardless of the specimen's gauge length and size, and allows measurement of local strain as well as gauge-length strain. The reliability of this concept was verified by applying it to tensile testing.

Objective: Subclinical left ventricular disfunction (LVD) is common in asymptomatic patients with type 2 diabetes (T2D). Many patients with diabetes have an impaired diastolic and systolic function. With preserved ejection fraction LV (EFLV), the latter is defined as reduced global longitudinal strain (GLS), detected using the speckle-tracking echocardiography. This study is aimed to define the long-term structural and functional disorders of the LV myocardium in patients with T2D without CVD. Methods: Of the 120 patients with and without T2D of both sexes aged from 45 to 75 years (57.11±7.9 years), included in the study in 2012-2013, only 57 responded to the follow-up study. The patients were divided into two groups: one with T2D (n=29), the other without it, control (n=28). All patients underwent transthoracic two-dimensional echocardiography with assessment of standard indicators of systolic and diastolic cardiac function, as well as GLS. In addition, all participants underwent laboratory diagnostics of carbohydrate metabolism disorders markers, NT-proBNP and CRP. The median follow-up duration was 7.2 [7.0-7.8] years. Results: During the follow-up, a statistically significant increase in the incidence of diastolic dysfunction (DD) in the type 2 diabetes group was found from 53% to 61% (p = 0.004); no significant dynamics were noted in the control group (p = 0.48). The presence of T2D significantly increases the risk of developing DD (p=0.04). The presence of T2D, increased fasting glucose levels, and an increased HOMA index were independent predictors of the development of DD. Impairment of LVEF was not observed in both groups. At the same time, the proportion of patients with reduced GLS (< -18%) increased in the T2D group (p = 0.036). A significant difference in the frequency of decreased GLS depending on T2D was demonstrated. The presence of obesity, an increase in the HOMA index and an increase in CRP levels are independent predictors of impaired GLS. Conclusions: T2D is an independent risk factor for the worsening of subclinical left ventricular dysfunction in asymptomatic patients with T2D without CVD over 7-year follow-up. Diastolic dysfunction is represented by delayed relaxation of the LV myocardium; with preserved LVEF, reduced 2D GLS identifies systolic dysfunction. The tight control of glycemia, lipidemia, blood pressure and body weight is associated with the absence of poor clinical outcomes.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

Background: We aimed to evaluate whether baseline GLS and NT-proBNP and their changes after cardiac resynchronization therapy (CRT) can predict the long-term clinical outcomes and the echocardiographic-based response to CRT (defined by 15% relative reduction in left ventricular end-systolic volume). Methods: We enrolled 143 patients with stable, ischemic heart failure (HF) undergoing CRT-D implantation. NT-proBNP and echocardiogram were obtained before and 6 months after. The patients were followed-up (median: 58 months) for HF-related deaths and/or HF hospitalizations (primary endpoint) or HF-related deaths (secondary endpoint) Results: 84 patients achieved the primary and 53 the secondary endpoint, while 104 patients were considered as CRT-responders and 39 as non-responders. At baseline, event-free patients had higher absolute GLS values (p&lt;0.001) and lower NT-proBNP serum levels (p&lt;0001) than those achieving primary endpoint. A similar pattern was observed in favor of CRT-responders vs non-responders. In Cox regression analysis, lower baseline absolute GLS value (HR=0.77;95%CI, 0.51-1.91; p=0.002), higher baseline NT-proBNP levels (HR=1.55;95%CI, 1.43-2.01;p=0.002) and diabetes (HR=1.27;95%CI, 1.12-1.98;p=0.003) were associated with lower incidence of primary endpoint. Conclusions: In HF patients undergoing CRT-D, baseline GLS and NT-proBNP concentrations may serve as prognostic factors, while they may predict the echocardiographic-based response to CRT.

Fiber-based flexible sensors have promising applications potential in human motion and healthcare monitoring, owing to their merits of lightweight, flexibility, and easy processing. Now, high-performance elastic fiber-based strain sensors with high sensitivity, large working range and excellent durability are in great demand. Herein, we have easily and quickly prepared a highly-sensitive, durable fiber-based strain sensor by dip-coating of highly-stretchable polyurethane (PU) elastic fiber in MXene/ waterborne polyurethane (WPU) dispersion solution. Benefiting from the electrostatic repulsion force between the negatively charged WPU and MXene sheets in the mixed solution, very homogeneous and stable MXene/WPU dispersion was successfully obtained and the interconnected conducting networks were correspondingly formed in coated MXene/WPU shell layer, which makes as-prepared strain sensor exhibit a gauge factor of over 960, a large sensing range of over 90% and detection limit as low as 0.5% strain. As elastic fiber and mixed solution have the same polymer constitute, tight bonding of MXene/WPU conductive composite on PU fibers was achieved, enabling the as-prepared strain sensor endure over 2500 stretching-releasing cycles and thus show good durability. Full-scale human motion detection was also performed by the strain sensor, and a body posture monitoring, analysis, and correction prototype system was developed via embedding the fiber-based strain sensors into sweater, strongly indicating the great application prospect in exercise, sports and healthcare.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

The initiation of micro-cracks in concrete is primarily due to its brittleness, which causes severe impacts on the overall behavior of the concrete. However, incorporating fibers in concrete could significantly improve its mechanical properties. The current study demonstrates the influence of two types of fibers on the mechanical properties of concrete. Nylon Fiber Threads (NFT) and Nylon Fiber Strands (NFS) at a fiber content of 2.5 kg/m³ were incorporated in the concrete mix. Concrete with a compressive strength of 30 MPa and a water-cement ratio of 0.4 was produced to investigate the fresh and mechanical properties of conventional and nylon-fiber reinforced concrete (NFRC). The concrete prims and cylinders were tested for compressive, splitting, and flexural strength using ASTM standards (ASTM C-39, C-496, and D-790, respectively). It was found that NFT-reinforced samples achieved higher mechanical properties of concrete (13.05%) compared to NFS-reinforced samples. Test results showed that incorporation of nylon fibers (NF) in concrete decreased the compressive strength of cylindrical and cubical specimens by 0–10% and 5–15%, respectively. However, it increased the splitting tensile and flexural strengths by 0-15%, and 5-15% respectively. Furthermore, the incorporation of NF in concrete significantly improved the ductility and delayed the crack initiation in concrete.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

Mouse models are frequently used to study Huntington’s disease (HD). Onset and severity of neuronal and behavioral pathologies vary greatly between HD mouse models, which results from different huntingtin expression levels and different CAG repeat length. HD pathology appears to depend also on strain background of mouse models. Thus, behavioral deficits of HD mice are more severe in the FVB than in the C57BL/6 background. Alterations in medium spiny neuron (MSN) morphology and function has been well documented in young YAC128 mice in the FVB background. We here tested the relevance of strain background for mutant huntingtin (mHTT) toxicity on the cellular level by investigating HD pathologies in YAC128 mice in the C57BL/6 background (YAC128/BL6). Morphology, spine density, synapse function and membrane properties were not or only subtly altered in MSNs of 12-month-old YAC128/BL6 mice. Despite the mild cellular phenotype, YAC128/BL6 mice showed deficits in motor performance. More pronounced alterations in MSN function were found in the HdhQ150 mouse model in the C57BL/6 background (HdhQ150/BL6). Consistent with the differences in HD pathology, the number of inclusion bodies was considerably lower in YAC128/BL6 mice than HdhQ150/BL6 mice. This study highlights the relevance of strain background for mHTT toxicity in HD mouse models.

Because of an often complicated and difficult-to-access care system, help-seeking for people with suspected dementia can be stressful. Difficulty in help-seeking may contribute to carer burden, in addition to other known stressors in dementia care. This study examined the relationship between perceived help-seeking difficulty and carer burden, and the barriers contributing to perceived difficulty. We interviewed 110 carers accessing a community-based dementia assessment service for suspected dementia of a family member for their perceived difficulty, delays, and barriers in help-seeking, and carers burden in terms of role strain, self-criticism, and negative emotions. Linear regression models showed that perceived help-seeking difficulty is associated with carer self-criticism, while carer role strain and negative emotions are associated with symptom severity of the person with dementia but not help-seeking difficulty. Inadequate knowledge about symptoms, service accessibility, and affordability together explained more than half of the variance in perceived help-seeking difficulty (Nagelkerke R2 = .56). Public awareness about symptoms, support in navigating service, and financial support may reduce perceived difficulty in help-seeking, which in turn may reduce carer self-criticism during the early course of illness.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

A galvalume corrugated sheet was utilized as formwork for a reinforced concrete beam in flexure. A numerical model was validated to the experimentally obtained data, and further adopted to simulate the behavior of this composite structure under elevated temperatures. The properties and constitutive stress-strain data of the basic materials were obtained from experiments, and superimposed into the finite element model. The study concluded that the load carrying capacity of the member decreased as a direct function on temperature increase, and the cracking moment was very sensitive to the temperature fluctuation. The elevated temperatures also altered the failure mode.

Desmoglein 3 (Dsg3) plays a crucial role in cell-cell adhesion and tissue integrity. Increasing evidence suggests that Dsg3 acts as a regulator of cellular mechanotransduction, but little is known about its direct role in mechanical force transmission. The present study investigated the impact of cyclic strain and substrate stiffness on Dsg3 expression and its role in mechanotransduction in keratinocytes. A direct comparison was made with E-cadherin, a well-characterized mechanosensor. Exposure of oral and skin keratinocytes to equiaxial cyclic strain promoted changes in expression and localization of junction assembly proteins. Knockdown of Dsg3 by siRNA blocked strain-induced junctional remodeling of E-cadherin and Myosin IIa. Importantly, the study demonstrated that Dsg3 regulates the expression and localization of YAP, a mechanosensor and an effector of the Hippo pathway. Furthermore, we showed that Dsg3 forms a complex with phospho-YAP and sequestered it to the plasma membrane, while Dsg3 depletion had an impact on both YAP and phospho-YAP in their response to mechanical forces, increasing the sensitivity of keratinocytes to strain- or substrate rigidity-induced nuclear relocation of YAP and phospho-YAP. PKP1 seemed to be crucial in recruiting the complex containing Dsg3/phospho-YAP to the cell surface since its silencing affected both Dsg3 junctional assembly with concomitant loss of phospho-YAP at cell periphery. Finally, we demonstrated that this Dsg3/YAP pathway has an influence on the expression of YAP1 target genes and cell proliferation. Together, these findings provide evidence of a novel role for Dsg3 in keratinocyte mechanotransduction.

Catechol dioxygenases in microorganisms cleave catechol into cis-cis-muconic acid or 2-hydroxymuconic semialdehyde via the ortho- or meta-pathway, respectively. The aim of the study was to purify, characterize and predict template-based three-dimensional structure of catechol 1,2-dioxygenase (C12O) from indigenous Pseudomonas chlororaphis strain UFB2 (PcUFB2). Preliminary studies showed that PcUFB2 could degrade 40 ppm of 2,4-dichlorophenol (2,4-DCP). The crude cell extract showed 10.34 U/mL of C12O activity with a specific activity of 2.23 U/mg of protein. A 35 kDa protein was purified to 1.5-fold with total yield of 13.02 % by applying anion exchange and gel filtration chromatography. The enzyme was optimally active at pH 7.5 and temperature 30 °C. The Lineweaver-Burk plot showed the v_max and K_m values of 16.67 µM/min and 35.76 µM, respectively. ES-MS spectra of tryptic digested SDS-PAGE band and bioinformatics studies revealed that C12O share 81% homology to homogentisate 1,2-dioxygenase reported in other Pseudomonas chlororaphis strains. Characterization and optimization of C12O activity can assist in understanding the 2,4-DCP metabolic pathway in PcUFB2 and its possible application in bioremediation strategies.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

It is imperative to conduct experimental studies on the seepage behavior of gas-bearing coal under cyclic dynamic loading conditions. This paper focuses on the evolution of coal permeability under the combined effects of dynamic loading, static loading, and gas adsorption. The principal conclusions are as follows. (1) As the frequency and amplitude of dynamic loading increase, the development of pore and fissure structures within the coal body becomes increasingly pronounced during dynamic loading cycles, resulting in a gradual rise in permeability. Notably, as the coal approaches its yielding stage, the permeability can increase by up to 47%. (2) The permeability curve is divided into four regions: the compaction reduction zone, the oscillation zone, the gradual recovery zone, and the abrupt increase zone of failure. Ultimately, in the failure phase, the permeability surges dramatically, potentially reaching 4 to 5 times the initial permeability. (3) When the static load stage is constant, the rate of change in permeability of the coal under dynamic loading decreases with increasing adsorption amount. When the adsorption amount is constant, the rate of change in permeability of the coal under dynamic loading increases with the increase in static load stress stage, with the maximum increase reaching 75.2%. It can be concluded from the rate of change in permeability and the dynamic loading sensitivity coefficient that the permeability of the coal is highly sensitive to cyclic dynamic loading, with increased sensitivity associated with larger static load stages and decreased sensitivity with greater adsorption amounts.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

In patients with heart failure, the evaluation of left ventricular (LV) diastolic function is vital, offering crucial insights into hemodynamic impact and prognostic accuracy. Echocardiography stands as the primary imaging modality for diastolic function assessment, and using it effectively requires a profound understanding of the underlying pathology. This review covers four main topics: first, the fundamental driving forces behind each phase of normal diastolic dynamics, along with the physiological basis of two widely used echocardiographic assessment parameters, E/e' and mitral annulus early diastolic velocity (e'); second, the intricate functional relationship between the left atrium and LV in patients with varying degrees of LV diastolic dysfunction (LVDD); third, the role of stress echocardiography in diagnosing LVDD and the significance of parameter changes in this context; and fourth, the clinical utility of evaluating diastolic function from echocardiography images across diverse cardiovascular care areas.

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

The extrusion-based 3D concrete printing (3DCP) technology allows the fabrication of permanent formwork with intricate shapes, into which fresh concrete is cast to build structural members with complex geometry. This significantly enhances the geometric freedom of concrete structures without the use of expensive temporary formwork. In addition, with proper material choice for the permanent formwork, the load-bearing capacity and durability of the resulting structure can be improved. This paper investigates 3DCP of permanent formwork for reinforced concrete (RC) beam construction. A 3D-printable engineered geopolymer composite (3DP-EGC, or strain-hardening geopolymer composite, 3DP-SHGC) recently developed by the authors was used for fabrication of the permanent formwork. The 3DP-EGC exhibits strain-hardening behaviour under direct tension. Two different printing patterns were used for the soffit of the permanent formwork to investigate the effect of this parameter on the flexural performance of RC beams. A conventionally mould-cast RC beam was also prepared as the control beam for comparison purposes. The results showed that the RC beams constructed using the 3DP-EGC permanent formwork exhibited superior flexural performance to the control beam. Such beams yielded significantly higher cracking load (up to 43%), deflection at ultimate load (up to 60%), ductility index (50%) and absorbed energy (up to 107%) than those of the control beam. The ultimate load was comparable with or slightly higher than that of the control beam. Furthermore, the printing pattern at the soffit of the permanent formwork was found to have a significant influence on the flexural performance of the RC beams.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

Electrochemical-mechanical interactions, in particular pressure-induced ones, have been identified to be a cause for lithium-plating in lithium-ion cells. Mechanically-induced porosity inhomogeneities in the separator layers due to electrode expansion during charging especially lead to cell internal balancing currents and can cause localized plating. To identify cell-format and cell-material dependent mechanical weak spots, a layer-resolved mechanical simulation of different cell types and cell-material combinations is presented in this work. The simulation results show distinctive layer strain patterns for different cell-types that coincide with localized lithium-plating found in post-mortem cells. Additionally, the effects of cell bracing in battery modules is investigated and a method to mitigate the increased layer strain due to bracing counterforces is proposed that also increases cell energy density for hardcase-type automotive cells.

Staphylococcus aureus is a high-priority pathogen causing severe infections with high morbidity and mortality worldwide. Many S. aureus strains are methicillin-resistant (MRSA) or even multi-drug resistant. It is one of the most successful and prominent modern pathogens. An effective fight against S. aureus infections requires novel targets for antimicrobial and antistaphylococcal therapies. Recent advances in whole-genome sequencing and high-throughput techniques facilitate the generation of genome-scale metabolic models (GEMs). Among the multiple applications of GEMs is drug-targeting in pathogens. Hence, comprehensive and predictive metabolic reconstructions of S. aureus could facilitate the identification of novel targets for antimicrobial therapies. This review aims at giving an overview of all available GEMs of multiple S. aureus strains. We downloaded all 114 available GEMs of S. aureus for further analysis. The scope of each model was evaluated, including the number of reactions, metabolites, and genes.Furthermore, all models were quality-controlled using Mᴇᴍᴏᴛᴇ, an open-source application with standardized metabolic tests. Growth capabilities and model similarities were examined. This review should lead as a guide for choosing the appropriate GEM for a given research question. With the information about the availability, the format, and the strengths and potentials of each model, one can either choose an existing model or combine several models to create models with even higher predictive values. This facilitates model-driven discoveries of novel antimicrobial targets to fight multi-drug resistant S. aureus strains.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

To analyze the predictive ability and incremental value of left ventricular longitudinal axis strain (LAS) and late gadolinium enhancement (LGE) using standard cardiovascular magnetic resonance (CMR) imaging for the diagnosis and prognosis of severe aortic stenosis (AS) in patients with an indication for aortic valve replacement. We conducted a prospective study on 128 patients with severe AS and 52 volunteers. The evaluation protocol included standard biochemistry tests, novel biomarkers of myocardial fibrosis, 12-lead electrocardiograms and 24-hour Holter, the 6-minute walk test and extensive echocardiographic and CMR imaging studies. Outcomes were defined as the composite of major cardiovascular events (MACEs). Among AS patients, most (n = 17, 77.2%) of those who exhibited LGE at CMR imaging had MACEs during follow-up. Kaplan-Meier curves for event-free survival showed a significantly higher rate of MACEs in patients with LGE (p < 0.01) and decreased LAS (p < 0.001). In Cox regression analysis, only reduced LAS [hazard ratio 1.33, 95%CI (1.01 to 1.74), p < 0.01] and the presence of LGE [hazard ratio 11.3, 95%CI (1.82 to 70.0), p < 0.01] were independent predictors for MACEs. The predictive value increased if both LGE and reduced LAS were added to LVEF. None of the biomarkers of increased collagen turnover exhibited any predictive value for MACEs. LAS by CMR is an independent predictor of outcomes in patients with AS and provides incremental value beyond the assessment of LVEF and the presence of LGE.

In this paper, the ductile fracture mechanism is discussed. The results of the numerical and experimental analyses are used to estimate of the onset of the crack front growth . It is assumed that the ductile fracture in front of the crack starts at the location along the crack front where the accumulated effective plastic strain reaches a critical value. It is also assumed that the critical effective plastic strain depends on the stress triaxiality and the Lode angle. The experimental programme was performed using five different specimen geometries, three different materials and three different temperatures of +20°C, -20°C and -50°C. Using the experimental data and the results of the finite element computations, the critical effective plastic strains are determined for each material and each temperature. However, before the critical effective plastic strain is determined, a careful calibration of the stress–strain curves was performed after modification of the Bai–Wierzbicki procedure. Finally, by analysing the experimental results recorded during the interrupted fracture tests and scanning microscopy observations, the research hypothesis is verified.

The analysis of the liquefaction potential of the ground is a fundamental characterization in areas with continuous seismic activity, such as Ecuador. Geotechnical liquefaction studies are usually approached from the application of dynamic penetration tests, which pose problems both in their execution and in their evaluation. The proposed research involves analyzing dynamic penetration tests and microtremor geophysical surveys (Horizontal to Vertical Spectral Ratio, HVSR technique) at the base of the San Marcos dam, a reservoir destined for the irrigation water located in Cayambe (Ecuador). Based on the investigations performed at the time of construction of the dam (drilling and geophysical refraction profiles) and the application of 20 microtremor observation stations performed by the HVSR technique, an analysis of the Safety Factor of liquefaction (SFliq) has been conducted, proposed by Youd and Idriss in 2001, and based on the values of the Standard Penetration Test (SPT) applied in granular materials (sands). In addition, the vulnerability index (Kg) proposed by Nakamura in 1989 was analyzed through the HVSR passive seismic records related to the Ground Shear Strain (GSS). The results obtained in the HVSR surveys indicate the presence of a zone of about 100 m length in the central part of the foot of the dam, whose GSS values are identified with a condition of susceptibility to liquefaction. In the same area, the analysis applied from SPT essays in the P-8A drill hole executed in said area also shows a potential susceptibility to liquefaction in earthquake conditions greater than a moment magnitude (Mw) of 4.5, which could occur in the environment, for example, with a new activity condition of the nearby Cayambe volcano or even from an earthquake from the vicinity fractured zone.

Wireless Sensor networks (WSNs) are gaining more and more research interest due to their ability to monitor large areas more or less independent. However, their reliability is an important issue, since their system reliability is influenced from a hardware, a data and an energetic point of view due to different factors like loading conditions, signal attenuation and battery lifetime. Regarding these issues, the positions of sensor nodes have to be chosen correctly to maximize the system reliability, which has to be considered during the development of new products equipped with WSNs. In this paper, an approach to estimate a WSNs system reliability during the development phase based on the analysis of the measurements on the example of strain measurements in finite elements (FE) models is presented. For that, the part under consideration is divided into regions with similar strains by the use of a Region Growing Algorithm (RGA). Afterwards, the WSN’s configuration is analyzed regarding its reliability in accordance to the data paths and measurement redundancy due to the sensor positions in the found measuring regions. This methodology is tested on an exemplary WSN configuration at an aircraft wing box under bending load and was found to work very well regarding the estimation of the hardware perspective on the system reliability. Therefore, the methodology and the developed algorithm show potentials for optimizations in sensor node positions for better reliability results.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Introduction: Carcinoid heart disease is a rare cause of right-sided valvular dysfunction, an important complication in patients with carcinoid syndrome. Objectives: We aim to present our own experience regarding early myocardial dysfunction in patients with carcinoid syndrome. Methods: 64 patients (35-90 year old, 62,5% female, 37,5% male patients) with carcinoid syndrome were evaluated be-tween October 2017 and June 2021. All patients underwent two-dimensional echocardiography with additional tissue Doppler and speckle-tracking techniques. For all patients there were measured urinary level of 5- hydroxyindolacetic acid, serotonin and NT-proBNP values. Results: The following echocardiographic features: global longitudinal strain of both ventricles, mean systolic velocity of the left ventricle, systolic velocity of the free wall of right ventricle, correlated with high values of specific biomarkers: serotonin, and urinary 5-hydroxyindolacetic acid, and also with the presence of hepatic metastases and poorly differentiated tumors. Discussion: In this study we identified several patients with early myocardial dysfunction due to carcinoid syndrome, representing a predictive model of poor prognosis, requiring further investigations. Conclusion: Echocardiographic assessment based on the measurement of systolic velocities, as well as the global longitudinal strain of both ventricles, together with specific biomarkers may contribute to better recognition of carcinoid heart disease in clinical practice, but this needs validation through further studies enrolling larger number of patients.

Thermal fluctuations in two-dimensional (2D) isotropy systems at non zero finite temperatures can destroy the long-range (LR) magnetic order due to Mermin-Wanger theory. Interestingly, the magnetic anisotropy related to spin-orbit coupling (SOC) could stabilize magnetic order in 2D systems. Recently, 2D FexGeTe2 (3≤x≤7) with high curie temperature (TC), as a typical 2D van der Waals metallic ferromagnet, has not only made significant progress in synthetic methods and controlling ferromagnetism (FM), but also actively explored many device applications. In this Review, we introduce six experimental methods, ten ferromagnetic modulation strategies, and three spintronic devices of 2D FexGeTe2 materials. Overall, we have outlined the challenges and potential research directions in this field.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

Since the first description of SARS-CoV-2 in China in 2019, thousands of variants have emerged worldwide. For some of them, the constellation of mutations caused changes in virus biology, pathogenicity, infectivityity and transmissibility resulting in dissemination throughout the world. Gamma variant (P.1) differs from SARS-CoV-2 Wuhan strain (B.1) by 12 amino acids in the Spike (S) protein, and presented mutations related to greater affinity for the receptor angioten-sin-converting enzyme 2 (ACE-2) and/or immune escape. The Gamma variant and subvariants were responsible for the second wave of COVID-19 in the Brazilian city of Manaus, characterized by high mortality and rapid transmission. The ability of variants to induce cytokine production may be closely related to their pathogenicity. Herein we observed that there was no significant difference in the quantity of cytokines among macrophages or neutrophils infected with P.1 and B.1 strains. Also, no significant difference was observed in the absolute number of macrophages and neutrophils infected with these variants. Furthermore, no evidence of SARS-CoV-2 replication was observed in macrophages when infected by the two analyzed variants. Our findings suggest that the difference in the epidemiological outcome observed during the P.1 variant spread when compared to B.1, it is not explained by differences in the quantity of cytokines and absolute number of macrophages or neutrophils. Through bioinformatics analysis of the S protein, we observed that the physicochemical differences between the variants and subvariants of P.1, probably refer to the degree of infectivity, due to the impact caused in the recognition of antibodies and receptor af-finity

The cyclic load applied to civil and mining structures can lead to a reduction of the materials’ strength, different from that which would occur with a monotonous load. Numerous cases can be found where the decay of the rock parameters subjected to this type of stress leads to progressive or sudden collapse: among them, tunnel walls, pillars and slabs in mining operations, roads with a heavy vehicle transit, abutments of bridges and dams can be quoted. The topic can therefore be fundamental for a correct structural design, to avoid problems during the life of the structure. However, given the heterogeneity of the rock materials and the difficulty of their characterization under this aspect, an unequivocal analysis is hardly achievable. Then, the discussion initially develops through a general historical review of the concept of fatigue, with a synthetic collection of case histories. The laboratory tests on rock samples are then examined and the most important results obtained are discussed. Finally, a comparison between different types of tests is proposed. The experimental data are expressed through the Wӧhler diagram. The goal is to fill the lack of design codes or standards in the field of cyclic stresses applied to rock materials, the understanding of its effect being of great interest in order to apply suitable parameters in the design phase.

A study on the selection of hyperelastic constitutive model for polymeric materials is performed using a hybrid experimental-computational approach. Bis-GMA polymer is used as a case study of hyperelastic material to describe the polymer characteristics by determining its Poisson’s ratio and its valid range of the hyperelastic stress-strain curves. These two parameters are then used to determine the hyperelastic constitutive model by using the hybrid approach. Several uniaxial compression tests along with their finite element simulations are implemented in a systematic way, to identify the polymer behavior under the compressive loading conditions. Nano-indentation experiments are conducted to verify the hyperelastic behavior of the polymer. The experimental and computational evidences confirm that the Poisson’s ratio of Bis-GMA is 0.40 and the appropriate hyperelastic constitutive model for this polymer is of a second order polynomial. It is shown that, the results can be used to determine the true stress-strain curve of hyperelastic materials.

Equal-Channel Angular Pressing (ECAP) is a method used to introduce severe plastic deformation into a metallic billet without changing its geometry. In special cases strain localization occurs and a pattern consisting of regions with high and low deformation (so-called shear and matrix bands) can emerge. This paper studies this phenomenon numerically adopting two-dimensional finite element simulations of one ECAP pass. The mechanical behavior of aluminum is modeled using phenomenological plasticity theory with isotropic or kinematic hardening. The effects of the two different strain hardening types are investigated numerically by systematic parameter studies: While isotropic hardening only causes minor fluctuations in the plastic strain fields, a material with high initial hardening rate and sufficient strain hardening capacity can exhibit pronounced localized deformation after ECAP. The corresponding finite element simulation results show a regular pattern of shear and matrix bands. This result is confirmed experimentally by ECAP-processing of AA6060 material in a severely cold worked condition, where microstructural analysis also reveals the formation of shear and matrix bands. Excellent agreement is found between the experimental and numerical results in terms of shear and matrix band width and length scale. The simulations provide additional insights regarding the evolution of the strain and stress states in shear and matrix bands.

Instrumental production is a crucial component of industrial and innovative development in the metalworking industry, where the drilling process plays a key role. Traditional twist drills with conventional cutting-edge designs, including a transverse edge, face several issues during drilling, such as difficult chip evacuation and high friction between the tool and the workpiece. These phenomena, in turn, lead to a deterioration in the quality of machined holes and a reduction in tool life. Existing methods of drill geometry modification only partially address these problems by reducing axial forces and increasing tool durability, but they do not provide a comprehensive improvement of the drilling process overall. The aim of this study is to develop and examine a new drill design—a double-point twist drill without a transverse edge, which ensures favorable cutting conditions, reduces tool wear, and increases tool durability during the drilling process. In the course of the study, experimental samples of the double-point drill were manufactured at the machine-building company LLP «Format Mach Company» (Pavlodar). For the experimental tests, a setup was developed that included the ZET 058 strain gauge system and Kistler piezoelectric force sensors. This combination allowed for a detailed investigation of cutting forces in a dynamic mode and recorded the loads acting on the tool in various directions, contributing to an objective evaluation of its performance. The experimental results showed that the double-point drill without a transverse edge significantly improves the drilling process by reducing axial and radial cutting forces, which helps to reduce tool wear and increase drill durability. This confirms the feasibility of applying this drill design to enhance the quality of hole machining and the efficiency of production processes in the metalworking industry. An increase in the durability of the new tool - a double-point twist drill without a transverse edge - was established at 2.2 times.

In the presented work, on the example of thin-walled specimens made by selective laser melting technology from AlSi10Mg subjected to preliminary heat treatment, it is shown that there is a critical point of transition from the elastic-plastic region of the engineering stress-strain diagram to the yield and fracture stresses. It was found that the critical point has a strong statistically significant correlation (0.83 by Spearman and 0.93 by Pearson) with the strain hardening coeffi-cient calculated in the section from yield strength to fracture strength. A regression equation linking the critical transition point to the strain hardening coefficient was obtained. It is shown that with increasing plasticity of thin-walled samples obtained by selective laser melting of AlSi10Mg leads to a change in the type of stress distribution in the elastic-plastic region (the Weibull distribution changes to a normal distribution) and the contribution of the probability density of stress distribution described by the Cauchy distribution with a mode near the fracture stress to the full probability density of fracture increases.

Rock materials failures are accompanied by the co-existence of various failure mechanisms, in-cluding rock fracturing, shearing, and compaction yield. These mechanisms manifest macro-scopically as multiple failure modes and nonlinear strength characteristics related to stress levels. Considering the limitations of current rock mechanics strength theories, which are primarily derived from single failure mechanisms, this study evaluates the applicability of alternative strength theories. Based on the extensional-strain criterion and the PMC (Paul-Mohr-Coulomb) model, a piecewise linear strength model was proposed that is suitable for analyzing multiple failure mechanisms in rocks and revealing the intrinsic mechanisms of multi-mechanism rock material failure. A multiple failure mechanism strength model in the form of inequalities was proposed, using the generalized shear stress, mean stress, and stress Lode angle as parameters. Strength tests conducted on sandstone and granite rock material samples under different stress conditions revealed distinct piecewise linear strength characteristics for both rock types, vali-dating the rationality and applicability of the multiple failure mechanism model. The findings construct a multi-mechanism failure model for rocks, providing enhanced predictive capabilities and aiding in the prevention of rock structural failures.

The manuscript presents a novel approach to designing and fabricating a stretchable patch antenna designed for strain sensing and wireless communication of sensing data at the same time. The challenge lies in combining flexible and stretchable textile materials with different physical mor-phologies, which can hinder adhesion among multiple layers when stacked up, resisting the overall stretchability of the antenna. The proposed antenna design overcomes this challenge by incorpo-rating a lattice hinge pattern in the non-stretchable conductive e-textile, transforming it into a stretchable structure. The innovative design includes the longitudinal cuts inserted in both the patch and the ground plane of the antenna, allowing it to stretch along in the perpendicular direction. Implementing the lattice hinge pattern over the conductive layers of the proposed patch antenna in combination with a 2 mm thick Polydimethylsiloxane (PDMS) substrate achieves a maximum of 25% stretchability compared to its counterpart antenna without lattice hinge design. The stretchable textile antenna resonates around a frequency of 2.45 GHz and exhibits a linear resonant frequency shift when strained up to 25%. This characteristic makes it suitable for use as a strain sensor. Ad-ditionally, the lattice hinge design enhances the conformability and flexibility of the antenna compared to a solid patch antenna. The realized antenna gains in the E and H-plane were measured as 2.21 dBi and 2.34 dBi, respectively. Overall, the presented design offers a simple and effective solution for fabricating a stretchable textile patch antenna for normal use or as a sensing element, opening up possibilities for applications in communication and sensing fields.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Creep deformation behaviour in single phase γ-TiAl alloy has been an extensively studied topic since the late 1970s. A lot of literatures have reported creep behaviour of γ-TiAl alloys, manufactured using different processing techniques [1]–[7]. The present discussion revisits the original work on understanding the tensile creep deformation behaviour of wrought single-phase γ-TiAl alloy by Hayes et al. [8] and is aimed to develop an understanding of steady state creep, through strain vs strain rate and strain vs ln(strain rate) plots. Besides, it also attempts to study the variation of stress exponent with temperature between 760-900⁰C and also, to determine activation energies using the two most common approaches, namely: Zener-Hollomon (Z-H) [9] and Sherby-Dorn (S-D, temperature compensated time approach) [10] for stress levels of 69 and 103.4 MPa between 760-900⁰C.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Corrugated cardboard is an ecological material, mainly because, in addition to virgin cellulose fibers also the fibers recovered during recycling process are used in its production. However, the use of recycled fibers causes slight deterioration of the mechanical properties of the corrugated board. In addition, converting processes such as printing, die-cutting, lamination, etc. cause micro-damage in the corrugated cardboard layers. In this work, the focus is precisely on the crushing of corrugated cardboard. A series of laboratory experiments were conducted, in which the different types of single-walled corrugated cardboards were pressed in a fully controlled manner to check the impact of the crush on the basic material parameters. The amount of crushing (with a precision of 10 micrometers) was controlled by a precise FEMat device, for crushing the corrugated board in the range from 10 to 70 % of its original thickness. In this study, the influence of crushing on bending, twisting and shear stiffness as well as a residual thickness and edge crush resistance of corrugated board was investigated. Then, a procedure based on a numerical homogenization, taking into account a partial delamination in the corrugated layers to determine the degraded material stiffness was proposed. Finally, using the empirical-numerical method, a simplified calculation model of corrugated cardboard was derived, which satisfactorily reflects the experimental results.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Detection of human movement requires lightweight, flexible systems to detect mechanical parameters (like strain and pressure) not interfering with user activity, and that he/she can wear comfortably. In this work we address such multifaceted challenge with the development of smart garments for lower limb motion detection, like a textile kneepad and anklet in which soft sensors and readout electronics are embedded for detecting movement of the specific joint. Stretchable capacitive sensors with a three-electrode configuration are built combining conductive textiles and elastomeric layers, and distributed at knee and ankle. They show an excellent behavior in the ~30% strain range, hence the correlation between their responses and the optically tracked Euler angles is allowed for basic lower limb movements. Bending during knee flexion/extension is detected, and it is discriminated from any external contact by implementing in real time a low computational algorithm. The smart anklet is designed to address joint motion detection in and off the sagittal plane. In this work, ankle dorsi/plantar flexion, adduction/abduction, and rotation are retrieved. Both smart garments show a high accuracy in movement detection, with a RMSE less than 4° in the worst case.

It is meaningful to monitor and identify the concrete cracks as they will seriously reduce the fatigue life of pavement. In this paper a new method based on distributed long-gauge optic fiber sensing is proposed to implement the crack identification. Firstly, the damage indicator, namely strain curve envelope area ratio (SCEAR), is proposed and calculated with the measured strain in time series when the plane goes across the pavement where the sensors are installed. Then the indicators with different sensors are normalization by the value of the indicator from one referenced sensor where damage normally will not happen. If the crack happens within the sensing gauge of the sensor, the value of damage indicator SCEAR from the sensor will increase. Therefore, the crack will be identified with the change of the damage indicator. The effect of the proposed method is first verified by some simulations of prefabricated pavement as the cracks can be accurately identified by the proposed method. Moreover, the influence from the aircraft, such as taxiing position, aircraft load and aircraft type, is not obvious enough to mislead the identification results. Lastly the static loading tests were implemented with one small-scale model of prefabricated concrete pavement in the lab. From the experimental results the prefabricated cracks inside the pavement slab can be identified accurately with the proposes method as the parameter SCEAR is increased by about 100% at the crack position, while it is only changed by about 3% at the undamaged position.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

The vacuum preloading method effectively strengthens the soft soil foundations with vertical drainage, which will produce a smear effect when laying sand drains. Meanwhile, the seepage of pore water and soil deformation during consolidation exhibits nonlinear characteristics. Therefore, based on Gibson's 1D large strain consolidation theory, this paper developed a more generalized large strain radical consolidation model of sand-drained soft foundations under free strain assumption. In this system, the double logarithmic compression permeability relationships for soft soils with large strain properties, the variation of the radical permeability coefficient in the smear zone, and the effect of the non-Darcy flow were all included. Then, the partial differential control equations were numerically solved by the finite difference method and validated with existing radical consolidation test results and derived analytical solutions. Finally, the influences of relevant model parameters on consolidation are discussed. The analysis shows that the greater the maximum dimensionless vacuum negative pressure P0, the faster the consolidation rate of sand-drained foundations. Meanwhile, the decrease in the negative pressure transfer coefficient k1 will result in a decreasing final settlement amount. Moreover, the consolidation rate of sand-drained foundations is slower considering the non-Darcy flow, but the final settlement is unaffected.

Tick-borne encephalitis virus (TBEV) is one of the most threatening pathogens which affects the human central nervous system (CNS). TBEV circulates widely in Northern Eurasia. According to ECDC the number of TBE cases increase annually. There is no specific treatment for the TBEV infection, thus vaccination is the main preventive measure. Despite the existence of several inactivated vaccines currently being licensed, the development of new TBEV vaccines remains a leading priority in countries endemic to this pathogen. Here we report new recombinant virus made by infectious subgenomic amplicon (ISA) approach using TBEV and yellow fever virus vaccine strain (YF17DD-UN) as a genetic backbone. The recombinant virus is capable of effective replication in mammalian cells and induce TBEV-neutralizing antibodies in mice. Unlike the original vector based on the yellow fever vaccine strain chimeric virus became neuroinvasive in doses of 107-106 PFU and can be used as a model of Flavivirus neuroinvasiveness, neurotropism and neurovirulence. These properties of hybrid structures are the main factors limiting their practical use as vaccines platforms.

Cannabidiol (CBD) is a non-intoxicating compound extracted from Cannabis sativa, showing antidepressant-like effects in different rodent models. However, inconsistent results have been described depending on the species and the strain used to assess depressive-like behaviour. Moreover, only a few studies have investigated the effect of CBD in female rodents. Therefore, we aimed to i) investigate the effects of CBD in two different strains of mice (Swiss and C57BL/6) and in a rat model of depression based on selective breeding (Flinders Sensitive and Resistant Lines, FSL and FRL) subjected to tests predictive of antidepressant-like effects; and ii) investigate the influence of sex in the effects of CBD in both mice and rats. CBD induced an antidepressant-like effect in male Swiss but not in female Swiss or C57BL/6 mice in the tail suspension test (TST). In male FSL rats, CBD produced an antidepressant-like effect one-hour post-injection. However, in female FSL, CBD induced a bimodal effect, increasing the immobility time at one hour and decreasing it at two hours. Ketamine produced an antidepressant-like effect in male and female FSL rats at different doses. In conclusion, strain, sex, and administration time affect CBD's behavioural response to rodents exposed to tests predictive of antidepressant effects.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

An in-depth study of the failure of granular materials, which is known as a mechanism to generate defects, can reveal the facts about the origin of the imperfections such as cracks in the carbon anodes. The initiation and propagation of the cracks in the carbon anode, especially the horizontal cracks below the stub-holes, reduce the anode efficiency during the electrolysis process. In order to avoid the formation of cracks in the carbon anodes, the failure analysis of coke aggregates can be employed to determine the appropriate recipe and operating conditions. In this paper, it will be shown that a particular failure mode can be responsible for the crack generation in the carbon anodes. The second-order work criterion is employed to analyze the failure of the coke aggregate specimens and the relationships between the second-order work, the kinetic energy, and the instability of the granular material are investigated. In addition, the coke aggregates are modeled by exploiting the discrete element method (DEM) to reveal the micro-mechanical behavior of the dry coke aggregates during the compaction process. The optimal number of particles required for the failure analysis in the DEM simulations is determined. The effects of the confining pressure and the strain rate as two important compaction process parameters on the failure are studied. The results reveal that increasing the confining pressure enhances the probability of the diffusing mode of the failure in the specimen. On the other hand, the increase of strain rate augments the chance of the strain localization mode of the failure in the specimen.

The objective of this study is to measure the crack propagation speed in three types of self-compacting concrete reinforced with steel fibers loaded under four different loading rates. Central-notched prismatic beams with two types of fibers (13 mm and 30 mm in length), three fiber volume ratios, 0.51%, 0.77% and 1.23%, were fabricated. Four strain gages were glued on one side of the specimen notch to measure the crack propagation velocity, a fifth one at the notch tip to estimate the strain rates upon the initiation of a cohesive crack and the stress-free crack. A servo-hydraulic testing machine and a drop-weight impact device were employed to conduct three-point bending tests at four loading-point displacement rates, the former to perform tests at 2.2 μm/s, 22 mm/s and the latter for those at 1.77 m/s, 2.66 m/s, respectively. With lower fiber contents, smooth mode-I cracks were formed, the crack speed reached the order of 1 mm/s and 20 m/s. However, crack velocities up to 1417 m/s were obtained for the concrete with high content of fibers under impact loading. This value is fairly close to the theoretically predicted terminal crack velocity of 1600–1700 m/s. Numerical simulations based on cohesive theories of fracture and preliminary results based on the technique of Digital Image Correlation are also presented to complement those obtained from the strain gages. In addition, the toughness indices are calculated under all four loading rates. Strain hardening (softening) behavior accounting from the initiation of the first crack is observed for all three types of concrete at low (high) loading rates. Significant enhancement in the energy absorption capacity is observed with increased fiber content.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

The crack geometry and associated strain field around Berkovich and Vickers indents on silicon have been studied by X-ray diffraction imaging and micro-Raman spectroscopy scanning. The techniques are complementary, the Raman data coming from within a few micrometers of the indentation, whereas the X-ray image probes the strain field at a distance of typically tens of micrometers. For example, Raman data provides an explanation for the central contrast feature in the X-ray images of an indent. Strain relaxation from breakout and high temperature annealing are examined and it is demonstrated that millimeter length cracks, similar to those produced by mechanical damage from misaligned handling tools, can be generated in a controlled fashion by indentation within 75 micrometers of the bevel edge of 200mm diameter wafers.

We developed a sensor optimized for joint motion monitoring by exploring the effects of stitch pattern, yarn thickness, and NP number on the performance of knitted strain sensors. We conducted stretching experiments with basic weft-knit patterns to select the optimal stitch pattern and analyze its sensitivity and reproducibility. The plain stitch with a conductive yarn located on the reverse side exhibited the highest gauge factor value (143.68) and achieved excellent performance, with a stable change in resistance even after repeated sensing. For in-depth analysis, we developed six sensors using the aforementioned pattern with different combinations of yarn thickness (1-ply, 2-ply) and NP number (12, 13, 14). Based on bending experiments, the GF across all sensors was 60.2–1092, indicating noticeable differences in sensitivity. However, no significant differences were observed in reproducibility, reliability, and responsiveness, confirming that all the sensors are capable of joint motion monitoring. Therefore, the plain-patterned plating stitch structure with conductive yarn on the reverse side is optimal for joint motion monitoring, and the yarn thickness and NP numbers can be adjusted to suit different purposes. This study provides basic data for developing knitted strain sensors and offers insights into how knitting methods impact sensor performance.

Halide perovskite are known by their (1) organic inorganic hybrid and (2) inorganic halide perovskite. Having this in mind, monolithic perovskite/silicon tandem solar cell has already demonstrated extraordinarily high performance in the field of photovoltaic with current efficiency of 29.15%, breaking the efficiency limit for silicon solar cell. Currently, halide perovskites become successful not only in photovoltaic but also in many other related potential optoelectronic applications. Because of this reason, the origin of their multifunctional properties, remarkable energy harvesting and emitting efficiency and the corresponding potential applications in various optoelectronic devices become controversial issues and hot topics of academic research this time. In this review, nano-engineering strategies, microscopic origins and mechanisms are reviewed well to make clarity on what the origin of multifunctional properties such as tunability, ferroelasticity, piezoelectricity, pyroelectricity and thermoelectric properties of halide perovskites. Moreover, the coexistence of multiple properties makes halide provskites possible for synergistic applications and multifunctional perspectives such as emerging energy harvesting, conversion technologies, nano-plasmonic sensing and electromechanical applications, which are now open for the scientific community for further detail investigations. To successfully explore this field, advanced nanometer scale domain characterization tools are highly relevant to understand the microscopic origin of these electrical properties; aid the commercial enterprises and the research institutions. Not only the microscopic origin but also identifying factors and issues affecting the successful understanding and presence or absence of these electrical parameters should be primary task in this review. Finally, the big challenges for operation of halide perovskites owing to temperature, moisture, light, air, etc. induced material degradation and device deteriorations as well as lattice instability, nano scale defects, surface and bulk defects should be considered while dealing with these future research topics.

The impact of systemic vascular resistance (SVR) in hypertrophic (HCM) and amyloid cardio-myopathies has been seldom investigated. We studied pressure-strain loop derived myocardial work (MW) indices and SVR in patients with either sarcomere HCM or wild type transthyretin cardiac amyloidosis (ATTR), presented with heart failure and preserved left ventricular ejection fraction (HFpEF) at the outpatient cardiology units at Messina and Catania University Hospitals (Italy). Patients were in sinus rhythm and needed to have good transthoracic ultrasound imaging quality to undergo transthoracic strain-echocardiography. Other than conventional parameters, SVR and GWI (global work index) were measured. Based on cross-tabulation (a way to assess the ventricular-arterial coupling), the patients were then classified in 4 classes according to the cut-off values suggested by previous studies of 1,440 dyne/s/cm-5 for SVR (Stefadouros et al., 1973) and 1576 mm Hg% for GWI (Olsen et al., 2022). Sixty patients, 30 in each group, aged 61±16 years, 78% males, were studied. HCM were younger than ATTR patients and in a better clinical status (23% HCM vs 77% ATTR were NYHA class 3, p<0.001). Overall, 51 patients (85%) showed high SVR, of whom 21 were HCM (70%) and 30 ATTR (100%) (p<0.005). Both, SVR and GWI were impaired (the poorest class C) in 43% HCM patients (with greater left ventricular concentric hypertrophy) vs 93% of ATTR patients (in advanced NYHA class) (p<0.001). In conclusion, assessing SVR and GWI in HFpEF patients with HCM or ATTR can help clinicians to interpret the pathophysiological and clinical features of such complex diseases.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

Intracranial compliance (ICC) plays a pivotal role in understanding the underlying mechanisms of various brain disorders and is of great clinical importance. Therefore, addressing the challenges in practical application of ICC is crucial for neurosurgeons. This study explored the significance of ICC assessment considering the time-dependency of specific brain disorders through two distinct approaches: short and large time elapsed (TE) in measuring volume or intracranial pressure (ICP) changes in the ICC equation (∆Volume/∆ICP). Variations in ICC values were observed across various ICC assessment methods and different TE values. Notably, the compensatory response of the brain exhibited non-monotonic and variable changes in a large TE for certain brain disorders, diverging from patterns observed in short TE assessments. Furthermore, the recovery behavior of the brain changed under different brain disorders when exposed to short and long TE conditions. These findings emphasized the dynamic nature of ICC and provided valuable insights into the correct practical assessment of ICC by selecting the appropriate TE, as well as considering the differences in strain rates and loading durations on the brain in different brain disorders. These insights also shed light on the reasons why, despite its clinical significance, ICC monitoring has not yet become a standard component of clinical care, unlike ICP monitoring.

The degradation of Proton-exchange membrane fuel cell (PEMFC) gasket materials is crucial in electric vehicles as it can cause hazardous hydrogen fuel leaks, which are usually due to high temperatures, pressures, and hydrogen fuel exposure. Degradation of gasket materials in PEMFC presents a critical concern for electric vehicle safety due to potential hydrogen fuel leaks. This study utilizes finite element analysis (FEA) to assess the suitability of gasket materials for PEMFC applications, focusing on aging and tensile conditions. The dual degradation framework, incorporating contact pressure and von Mises stress, is employed to evaluate Liquid Silicon Rubber (LSR) and Ethylene Propylene Diene Monomer (EPDM) materials. Under aging techniques, the Yeoh model exhibits the least Mean Absolute Percentage Error (MAPE) and computational cost of 0.27 seconds, while the Ogden model records the highest computational cost of 0.89 seconds. In evaluating MAE, Root Mean Square Error (RMSE), and R-squared metrics, LSR and EPDM materials demonstrate respective averages of 0.25%, 0.275%, 0.945%, and 0.815%, 0.685%, 0.77%. Tensile testing (Uniaxial) reveals RMSE and MAE values of 0.30%, 0.40%, and 0.50%, 0.40%, respectively. FEA proves instrumental in identifying suitable gasket materials for PEMFC applications. LSR emerges as the superior choice, demonstrating enhanced FEA modelling performance under aging and tensile conditions. These findings contribute valuable insights to the design and development of improved gasket materials, bolstering the safety and reliability of electric vehicles.

(1) Background: The proportion of fully mechanized harvesting systems in Austria is constantly increasing especially because of the technological development of the machines, which allows them to drive on increasingly steep terrain. This leads to additional challenges and potential hazards for the operators, which may also cause higher stress levels. The purpose of this study is to develop and debate a new set of methodologies for determining time and space resolved psychophysiology data to analyze stressful and non-stressful work situations for harvester and forwarder operators; (2) Methods: we suggest a study protocol to analyze a) tasks performed by the driver, b) environmental factors, like slope gradient, c) the psychophysiological response of experts during these tasks, and d) evaluate the worker´s subjective stress and fatigue before and after a harvest operation. (3) Results: Within this manuscript we present a study protocol based on quantitative and qualitative methods, like time and space resolved psychophysiology, questionnaires, qualitative interviews, as well as video and sensor-based analysis of environmental and machine data. The first results from real measurements of a forwarder driver are presented; (4) Conclusions: This multimodal research protocol serves to explore the relationship between stress, fatigue, and performed tasks. Through our quantitative and qualitative methodology, researchers can improve the health and safety of forest workers at work, improve their productivity and reduce damage to remaining trees.

Road-embedded inductive power transfer (IPT) systems have the potential to accelerate the electrification of the transportation sector. For these systems to be economically viable however, they need to have a similar durability and lifespan compared to that of asphalt roads. One area that has lacked investigation is thermally induced stresses in a primary IPT pad, which is caused by the increase in temperature of the pad when it is energized and the differing thermal expansion of the materials within. This paper presents an experimental and a finite-element based methodology for investigating the thermal-mechanical behaviour of a ¼-scale double-D pad, which was energized while suspended in air, as well as energized when embedded in pavement. A focus was placed on the measurement and prediction of strains in the magnetic ferrite cores because of their brittleness. Ferrite strains were measured using a combination of resistive strain gauges and non-metallic Fibre Bragg Grating (FBG) sensors. Coupled electromagnetic-thermal-structural simulations were conducted to predict temperature and strains in the system, with temperature-dependent properties obtained through physical testing. At an ambient temperature of 50°C, the temperature in the middle of the copper litz wire coil was predicted to be 100°C in both the suspended and embedded case. There was excellent correlation to experimental results, with a difference of less than 10% for most temperature measurements. When energized, the pad was predicted to experience an upward bow due to its temperature rise, resulting bending strains in the ferrite cores. At an ambient temperature of 50°C, maximum tensile strain in the ferrites of the embedded pad was measured to be 62 microstrain (με), with a root-mean square error that was 18 με across three sensors. The experimental and validated numerical methodology can be applied to full-scale operational IPT pads to analyse and improve their thermal-mechanical performance.

The COVID-19 pandemic was declared in March 2020 and is still ongoing. The course of the epidemic remains uncertain, and mutations in the coronavirus, as well as the emergence of new variants of concern, make it possible that there will be periodic surges in the number of cases. Moreover, it is not clear how quickly and to what extent the effectiveness of vaccination will decline as the virus continues to mutate. One possible solution to combat the rapidly mutating coronavirus is the development of pan-coronavirus vaccines that stimulate the production of antibodies against conserved elements of the virus. Another approach could be the creation of safe vaccine platforms that can be rapidly adapted to deliver new, specific antigens in response to viral mutations. Recombinant probiotic microorganisms that can produce viral antigens by inserting specific viral DNA fragments into their genome show promise as a platform and vector for mucosal vaccine antigen delivery. With a well-established safety profile and the ability to transform into vaccine candidates, probiotic bacteria have significant research potential. The authors of this study have developed a convenient and universal technique for inserting the DNA sequences of pathogenic bacteria and viruses into the gene that encodes the pili protein of the probiotic strain E. faecium L3. The paper presents data on the immunogenic properties of two E. faecium L3 vaccine strains, which produce two different fragments of the coronavirus S1 protein, and provides an assessment of the protective efficacy of these oral vaccines against coronavirus infection in Syrian hamsters.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

This work describes a new transducer prototype for continuous monitoring both in the structural and geotechnical fields. The transducer is synthetically constituted by a wire of optical fiber embedded between two fiber tapes (fiberglass or carbon fiber) and glued by a matrix of polyester resin. The fiber optical wire ends have been connected to a control unit whose detection system is based on Brillouin optical time-domain frequency analysis. Three laboratory tests were carried out to evaluate the sensor's reliability and accuracy. In each experiment, the transducer was applied to a sample of inclinometer casing sets in different configurations and with different constraint conditions. The experimental data collected were compared with theoretical models and with data obtained from the use of different measuring instruments to perform validation and calibration of the transducer at the same time. Several diagrams allow comparing the transducer and highlighting its suitability for monitoring and maintenance of structures. The characteristic of the transducer suggests its use as a mixed system for reinforcing and monitoring, especially in lifetime maintenance of critical infrastructures such as transportation and service networks, and historical heritage.

This study explores the application of numerical analysis and material models to predict ice impact loads on ships and offshore structures operating in polar regions. An explicit finite element analysis (FEA) approach was employed to simulate an ice and steel plate collision experiment conducted in a cold chamber. The pressure and strain history during the ice collision were calculated and compared with the experimental results. Various material model configurations were applied to the FEA to account for the versatile behavior of ice—whether ductile or brittle—its elastic-plastic yield criteria, and its dynamic strain rate dependency. In addition to the standard linear elastic perfectly plastic and linear elastic-plastic relationships, this study incorporated the crushable foam and Drucker-Prager models, based on the specific ice yield criteria. Considering the ice’s strain rate dependency, collision simulations were conducted for each yield criteria model to compute the strain and reaction force of the plate specimens. By comparing the predicted pressures for each material model combination with the pressures from ice collision experiments, our study proposes material models that consider the yielding, damage, and behavioral characteristics of ice. Lastly, our study proposes a combination of ice material properties that can accurately predict collision force.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

Heart transplantation (HT) represents the mainstream therapy of end-stage heart failure for selected patients with a median survival of more than 10 years after surgery and substantial improvement in quality of life. Current guidelines suggest a variety of examinations including invasive (coronary angiography and endomyocardial biopsy (EBM) and non-invasive methods (echocardiography, stress echocardiography, computed tomography, PET and MRI) to monitor HT patients. Guidelines do not specify the timing of echocardiographic evaluations and do not recommend echocardiography as an alternative to serial EMB in rejection monitoring [2]. They still recommend as gold standard coronary angiography to be done 1 year after surgery and every 2 years after. In this review we will discuss the advantages of non-invasive techniques over the invasive ones for an adequate follow-up of HT patients.

Truffles are ascomycete hypogeous fungi belonging to the Tuberaceae family of the Pezizales order that grow in ectomycorrhizal symbiosis with tree roots and are known for their peculiar aromas and flavors. Axenic culture of truffle mycelium is problematic because it is not possible in many cases, and the growth rate is meager when it is possible. This limitation prompts searching and characterizing new strains that can be handled in laboratory conditions for basic and applied studies. In this work, a new strain of Tuber borchii (strain SP1) has been isolated and cultured, and its transcriptome has been analyzed under different in vitro culture conditions. The results show that the best T. borchii SP1 growth was obtained using maltose-enriched cultures made with soft-agar and in static submerged cultures made at 22ºC. The transcriptome analysis of this strain cultured in different media indicated that most of the gene transcription effort is due to a limited number of genes (20% of genes account for 80% of the transcription), that the transcription profile of the central metabolism genes was similar in the different conditions analyzed with a transcription signal detected for around 80% of the annotated genes. The gene expression profile suggests that T. borchii uses a fermentative rather than respiratory metabolism, even in aerobic conditions. Finally, there is a reduced expression of genes belonging to secondary metabolite clusters, whereas there is a significative transcription of those involved in producing volatile aromatic compounds.

We aimed to delineate cardiopulmonary interactions in acute bronchiolitis and to evaluate the capacity of a combined cardiopulmonary ultrasonography to predict the need for respiratory support. This was a prospective observational single-center study that includes infants < 12 month of age admitted to a hospital due to acute bronchiolitis. All the included patients under-went clinical, laboratory and cardiopulmonary ultrasonographic evaluation at the same time point within 24 hours of hospital admission. The existence of significant correlation between car-diac and respiratory parameters was the primary outcome. The association of different cardio-pulmonary variables with the need of respiratory support higher than O2, the length of stay hos-pitalization, the PICU stay, and the duration of respiratory support were a secondary outcome. We enrolled 112 infants (median age 1 (0.5-3) months; 62% males) hospitalized with acute bron-chiolitis. Increased values of the pulmonary variables (BROSJOD score, pCO2 and LUS) showed moderate correlations with NT-proBNP and all echocardiographic parameters indicative of pulmonary hypertension and myocardial dysfunction. Up to 36 (32%) infants required respira-tory support during the hospitalization. This group presented with higher lung ultrasound score (p<0.001), and increased values of Tei index (p<0.001) and pulmonary artery pressures (p<0.001). All the analyzed respiratory and cardiac variables showed moderate to strong correlations with the LOS hospitalization and the time of respiratory support. Lung ultrasound and echocardiog-raphy showed a moderate to strong predictive accuracy for the need of respiratory support in the ROC analysis, with AUC varying from 0.74 to 0.87. Conclusion: Those cases of bronchiolitis with a worse pulmonary status presented with a more impaired cardiac status. Cardiopulmonary ul-trasonography could be a good strategy to easily identify high-risk population for a complicated acute bronchiolitis hospitalization.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

Interference fits are a very common shaft-hub connection due to their low manufacturing cost and excellent technical properties. Plastic Conditioning of this machine element is a new and not very well known method. By exploiting residual stresses and the associated increase in the yield point, these components can absorb operating loads such as rotating bending moments, torsion, temperature changes and centrifugal forces purely elastically and avoid plastic deformation during operation. Compared to conventionally joined interference fits, the load bearing capacity in the elastic range can be increased by almost 200% and a specifically defined additional safety against plastic deformation in the elastic-plastic range can be ensured. This paper examines the effects of Reverse Yielding on the technology of Plastic Conditioning of Interference Fits in Power Transmission Engineering. Based on the Shear Stress Hypothesis (SH), the Plane Stress State (PSS) and the ideal plastic behavior of materials, the stress-mechanical relationships are explained, the influencing parameters are examined and conclusions are drawn for the plastic conditioning process. Taking into account the theoretical knowledge according to the state of the art, modified material behavior assumptions (isotropic hardening) and the Von Mises Yield Criterion (VMYC) are also considered. In addition, the method of plastic conditioning of interference fits is introduced and its basic principles are briefly explained. Along with computational suggestions to avoid Reverse Yielding, open issues requiring further research are identified.

This study provides a contribution to the research field of 3D printed earthen buildings, focusing, for the first time, on the load-bearing capacity of these structures. The study involves the entire production and testing process of the earthen elements, from design, to the preparation of the mixture and the 3D printing, up to the uniaxial compression test on a wall segment. The results indicate that 3D printed earthen elements have a compressive strength of 2.32 MPa, comparable to that of rammed earth structures. The experimental data also made it possible to draw conclusions on the action of the infill, which seems to have the function of stopping the propagation of cracks. This has a positive effect on the overall behavior of 3D printed earthen elements, since it avoids the onset of dilative behavior in the final stages of the load test and maintains ultimate load values higher than 50% of the maximum load.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

Background. Transcatheter edge-to-edge repair (TEER) is a safe and effective treatment in symptomatic patients with mitral regurgitation (MR). We aimed to investigate the short-term impact of mitral TEER on left ventricular (LV) performance and identify echocardiographic prognostic indicators. Methods. Seventy-eight patients with severe MR (organic and functional etiologies) were included retrospectively. All patients had a baseline and short-term echocardi-ography after TEER and were followed up for the primary composite endpoint (heart failure hos-pitalization and cardiovascular death) over a median period of 13 months. Results. A significant decrease in left ventricular ejection fraction (LVEF), all myocardial work indices (except global wasted work), and left atrial reservoir were observed after TEER. Additionally, there was an im-provement in the pulmonary artery systolic pressure and tricuspid annular plane systolic excur-sion/pulmonary artery systolic pressure (TAPSE/PASP) ratio. 34% of all patients presented the primary composite endpoint. A TAPSE/PASP ratio post-TEER < 0.47 (HR: 4.76, p-value = 0.039), and left atrial reservoir post-TEER < 9.0% (HR: 2.77, p-value = 0.047) were independently associ-ated with the primary endpoint. Conclusions. Echocardiography post-TEER reflects impairment in ventricular performance due to preload reduction and right ventricular to pulmonary artery coupling improvement. Short-term echocardiography after TEER identifies high-risk patients who could benefit from a close clinical follow-up.

Influenza virus strain A/South Africa/3626/2013 (H1N1)pdm09 (SA-WT) is a non-mouse-adapted model strain, which has naturally high pathogenic properties for mice. It has been suggested that the high pathogenicity of this strain for mice could be due to the three strain-specific substitutions in the polymerase complex (Q687R in PB1, N102T in PB2, and E358E/K heterogeneity also in PB2). To evaluate the role of these replacements, SA-WT was passaged five times in mouse lungs, and the genome of the mouse-adapted version of the SA-WT strain (SA-M5) was sequenced. SA-M5 lost E358E/K heterogeneity and retained E358, which is the prevalent amino acid at this position among H1N1pdm09 strains. Besides, in the hemagglutinin of SA-M5, two heterogeneous substitutions (G155G/E and S190S/R) were identified. Both viruses, SA-M5 and SA-WT, were compared for their toxicity, ability to replicate, pathogenicity, and immunogenicity for mice. In mice infected with SA-M5 or SA-WT strains, toxicity, virus titer in pulmonary homogenates, and mouse survival did not differ significantly. Contrarily, an increase in the immunogenicity of SA-M5 compared to SA-WT was observed. This increase could be due to the substitutions G155G/E and S190S/R in the HA of SA-M5. The prospects for using SA-M5 in studying the immunogenicity mechanisms were also discussed.

Conducting computational stress-strain analysis using finite element methods (FEM) is a common approach when dealing with the complex geometries of atherosclerosis, which is a leading cause of global mortality and complex cardiovascular disease. The considerable expense linked to FEM analysis encourages the substitution of FEM with a considerably faster data-driven machine learning (ML) approach. This study investigated the potential of end-to-end deep learning tools as a more effective substitute for FEM in predicting stress-strain fields within 2D cross sections of arterial wall. We first proposed a U-Net based fully convolutional neural network (CNN) to predict the von Mises stress and strain distribution based on the spatial arrangement of calcification within arterial wall cross-sections. Further, we developed a conditional generative adversarial network (cGAN) to enhance, particularly from the perceptual perspective, the prediction accuracy of stress and strain field maps for arterial walls with various calcification quantities and spatial configurations. On top of U-Net and cGAN, we also proposed their ensemble approaches to further improve the prediction accuracy of field maps. Our dataset, consisting of input and output images, was generated by implementing boundary conditions and extracting stress-strain field maps. The trained U-Net models can accurately predict von Mises stress and strain fields, with structural similarity index scores (SSIM) of 0.854 and 0.830 and mean squared errors of 0.017 and 0.018 for stress and strain, respectively, on a reserved test set. Meanwhile, the cGAN models in a combination of ensemble and transfer learning techniques demonstrate high accuracy in predicting von Mises stress and strain fields, as evidenced by SSIM scores of 0.890 for stress and 0.803 for strain. Additionally, mean squared errors of 0.008 for stress and 0.017 for strain further support the model's performance on a designated test set. Overall, this study developed a surrogate model for finite element analysis, which can accurately and efficiently predict stress-strain fields of arterial walls regardless of complex geometries and boundary conditions.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

Insufficient mixing in large-scale bioreactors, provokes gradient zones of substrate, dissolved oxygen, pH and other parameters. E. coli responds to a high glucose, low oxygen feeding zone with the accumulation of mixed acid fermentation products, especially formate, but also with the synthesis of non-canonical amino acids, such as norvaline, norleucine and -methyl-norleucine. These amino acids can be mis-incorporated into recombinant products, which causes a problem for pharmaceutical production whose solution is not trivial. While these effects can also be observed in scale down bioreactor systems, these are challenging to operate. Especially the high-throughput screening of clone libraries is not easy, as fed-batch cultivations would need to be controlled via repeated glucose pulses with simultaneous oxygen limitation, as has been demonstrated in well controlled robotic systems. Here we show that not only glucose pulses in combination with oxygen limitation can provoke the synthesis of these non-canonical branched-chain amino acids, but also that pyruvate pulses produce the same effect. Therefore we combined the enzyme based glucose delivery method Enbase® in a PALL24 mini-bioreactor system and combined repeated pyruvate pulses with simultaneous reduction of the aeration rate. These cultivation conditions, produced an increase in the non-canonical branched chain amino acids norvaline and norleucine in both the intracellular soluble protein and inclusion body fractions with mini-proinsulin as an example product, and this effect was verified in a 15 L stirred tank bioreactor. To our opinion this cultivation strategy is easy to apply for the screening of strain libraries under standard laboratory conditions if no complex robotic and well controlled parallel cultivation devices are available.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

Durability monitoring of insecticide-treated nets (ITNs) containing a pyrethroid in combination with a second active ingredient (AI) must be adapted so that the insecticidal bioefficacy of each AI can be monitored independently. An effective way to do this is to measure rapid knock down of a pyrethroid-susceptible strain of mosquitoes to assess the bioefficacy of the pyrethroid component and to use a pyrethroid-resistant strain to measure the bioefficacy of the second ingredient. To allow robust comparison of results across tests within and between test facilities, and over time, protocols for bioefficacy testing must include either characterisation of the resistant strain, standardisation of the mosquitoes used for bioassays, or a combination of the two. Through a series of virtual meetings, key stakeholders and practitioners explored different approaches to achieving these goals. Via an iterative process we decided on the preferred approach and produced a protocol consisting of characterising mosquitoes used for bioefficacy testing before and after a round of bioassays, for example at each time point in a durability monitoring study. We present the final protocol and justify our approach to establishing a standard methodology for durability monitoring of ITNs containing pyrethroid and a second AI.

Natural products have long played a major role in medicine and science. The garden snail Cornu aspersa is a rich source of biologically active natural substances which might be an important source for new drugs to treat human disease. Based on our previous studies seven fractions containing compounds with Mw &lt;3 kDa, &lt;10 kDa, &lt;20 kDa, &gt;20 kDa, and between 3-5 kDa, 5-10 kDa, and 10-30 kDa were purified from the mucus of C. aspersa and analyzed by tandem mass spectrometry (MALDI-TOF/TOF). Seventeen novel peptides with potential antibacterial activity have been identified by de novo MS/MS sequencing using tandem mass spectrometry. The different fractions were tested for antibacterial activity against Gram─ (Pseudomonas aureofaciens and Escherichia coli) and Gram+ (Brevibacillus laterosporus) bacterial strains as well anaerobic bacterium Clostridium perfringens. These results revealed that the peptide fractions exhibit a predominant antibacterial activity against B. laterosporus, the fraction with Mw 10 – 30 kDa against E. coli, another peptide fraction &lt;20 kDa against P. aureofaciens, and the protein fraction &gt;20 kDa against the bacterial strain C. perfringens. The discovery of new antimicrobial peptides (AMPs) from natural sources is of great importance for public health due to their effective antimicrobial activities and low resistance rates.