Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

RM (red mud) was acidified with sulphuric acid and the acidified ARM (acidified red mud) was utilized as an innovative adsorption material for treating antibiotic-contained wastewater. The adsorption conditions, kinetics, isotherms, thermodynamics, and mechanism of ARM for CIP (ciprofloxacin) were investigated. Characterization of the ARM involved techniques such as scanning electron microscopy(SEM), transmission electron microscope(TEM), brunauer- emmett-teller (BET), X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetric analysis (TGA) and NH3-TPD analysis. Adsorption studies were conducted employing response surface methodology (RSM) for experimental design. The results showed that ARM can absorb CIP effectively. The RSM optimal experiment indicated that the most significant model terms influencing adsorption capacity were solution pH, CIP initial concentration and ARM dosage, under which the predicted maximum adsorption capacity achieved 7.30 mg/g. The adsorption kinetics adhered to a pseudo-second-order model, while equilibrium data fitted the Langmuir-Freundlich isotherm, yielding maximum capacity values of 7.35 mg/g. The adsorption process occurred non-spontaneously and absorbed heat, evidenced by ΔG0 values between 2.06 and 0.87 kJ/mol, ΔS0 at 39.41 J/mol/K, and ΔH0 at 13.8 kJ/mol. Analysis using attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) indicated there existed complex reaction between Al-O in ARM and the ester group –COO in CIP. The C=O bond in CIP was likely to undergo a slight electrostatic interaction or be bound to the internal spherical surface of ARM. The findings indicate that ARM is a promising and efficient adsorbent for CIP removal from wastewater.

Statement of problem: Henna has been added to polymethylmethacrylate (PMMA) as a new type of antifungal agent; however, its effect on the latter’s physical properties has not been investigated. Purpose: This study aimed to evaluate the effect of the addition of various henna concentrations on the surface roughness and hardness of PMMA denture base material. Materials and Methods: A total of 99 specimens of rectangular-shaped (10×20×3 mm3) acrylic specimens were prepared from heat-cured acrylic resin. Specimens were divided into one control group without the addition of henna and five test groups, which were prepared by adding Yamani henna powder to acrylic powder at concentrations of 1wt%, 2.5wt%, 5wt%, 7.5wt%, and 10wt%. The polymer was added to the monomer before being mixed, packed, and processed using the conventional water bath method. After processing, specimens were finished and polished, then kept in distilled water for 48+2 h. A profilometer and Vickers hardness tester were used to measure surface roughness and hardness respectively. Statistical data analysis was conducted via SPSS version 20.0 (IBM, USA). Results: The addition of henna at varying concentrations significantly increased surface roughness values (P ≤ 0.01) while decreasing hardness (P ≤ 0.0001). The most favorable addition value was 1% henna between all henna groups. Conclusion: The addition of henna to the acrylic resin may negatively affect the surface properties of PMMA acrylic denture base.

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

Earth’s land surface area is raised from conventionally flat 15 to 64 Gha to account for hilly undulation and soil relief detail. Three main aspects are: topography, rugosity/tortuosity and micro-relief/porosity of vegetation-free ground. Recalibration is arrived at from four approaches: first, direct empirical estimates from the few compiled satellite or LiDAR data with means of +2.5–26% progressively overlain by +94% at cm² scale for soil ruggedness then +108% for mm² micro-relief; second, from digital elevation models with 1.6–2.0 times flat areas; third, by ‘reverse engineering’ global soil bulk densities and carbon reserves requiring x 2–6 land. Finally, a Fermi estimation conveniently sets the World’s new surface area – that exposed to Sun, air and rain – at 100 Gha (with 36 Gha flat ocean). Soil organic carbon (SOC) is thence raised to 8,580 Gt mainly in SOM/humus with its biotic complexity plus roots, VAM-fungi and leaf-litter, that itself = 17,800 Gt. Although four to six times IPCC’s or NASA/NOAA’s calculations of just 1,500–2,300 Gt SOC, this is likely an underestimation. Global biomass and biodiversity are at least doubled (x 2–3.5) and net primary productivity (NPP) similarly increased on land to >270 Gt C yr^-1 due to terrain.

Building a new-type power system is the key core of the green and low-carbon development of energy, the restructuring of the power system will inevitably have a linked impact on the coordinated development of the economy-energy-environment (3E) system. This paper constructs a "Dual-Triangle" theoretical framework consisting of the “Energy Trilemma” and the "Sustainable Development Triangle", by combining historical statistical analysis with scenario predictive analysis, analyzes the historical characteristics of the "Dual Triangle" and future development trends under different scenarios, and studies the coupled interaction relationship of the "Dual-Triangle" to explore the optimal transformation path of the power system that is most beneficial to the coordinated development of the 3E system. The conclusions are as follows: (1) The energy system gradually inclined towards economy and cleanliness from 2010 to 2022, the level of coordinated development of the 3E system fluctuated upwards, and the operation status of the "Dual Triangle" was stable. (2) Positive coupling relationship between "Dual Triangle" of scenario S1 is close, which can be regarded as the preferred path for the reconstruction of the power system. Due to phased development has clear development priorities, scenario S2 will artificially break the balance of the “Energy Trilemma”, which is a development model that dynamically mitigates the challenges of the “Energy Trilemma”.(3)The contradiction between economy and cleanliness is continuously weakened, and security has become the core contradiction of the "Impossible Triangle". The combination of renewable energy and energy storage is the key to resolving this contradiction. This paper conducts an integrated and innovative application of the "Dual-Triangle" theory, and the results provide a case basis for how to achieve the coupled interaction of the "Dual-Triangle", promote high-quality energy development, and support the sustainable development of the economy and society.

Taste signaling is a complex process that is linked to obesity and its associated metabolic syndromes. The sweet taste is mediated through a heterodimeric G protein coupled receptor (GPRC) in a species-specific manner and at multi-tissue specific levels. The sweet receptor recognizes a large number of ligands with structural and functional diversities to modulate different amplitudes of downstream signaling pathway(s). The human sweet-taste receptor has been extremely difficult to study by biophysical methods due to inadequate methods for producing large homogeneous quantities of the taste-receptor protein and a lack of reliable in vitro assays to precisely measure productive ligand binding modes leading to activity upon their interactions with the receptor protein. We report a multimodal high throughput assays to monitor ligand binding, receptor stability and conformational changes to model the molecular interactions between ligand-receptor. We applied saturation transfer difference nuclear magnetic resonance spectroscopy (STD-NMR) complemented by differential scanning calorimetry (DSC), circular dichroism (CD) spectroscopy, and intrinsic fluorescence spectroscopy (IF) to characterize binding interactions. Our method using complementary NMR and biophysical analysis is advantageous to study the mechanism of ligand binding and signaling processes in other GPCRs.

Analysis of the correlation between indices (Normalized Difference Vegetation Index, Normalized Difference Barren Index and Modified Normalized Difference Water Index) and land surface temperature is used to natural resources and environmental studies. This research aimed to analysis of Land Surface Temperature due to dynamics of Different Indices (NDVI, NDBaI and MNDWI) Using Remote Sensing Data in three selected districts (Gida Kiremu, Limu and Amuru), western Ethiopia. From thermal and multispectral bands of landsat imageries (Landsat TM of 1990, landsat ETM+ of 2003 and landsat OLI/TIRS of 2020) Land surface temperature and NDVI, NDBaI and MNDWI were calculated. Correlation analysis was used to indicate relationships between LST with NDVI, NDBaI and MNDWI. The study found that Land Surface Temperature was increased by 5⁰C from 1990 to 2020. Vegetation areas (NDVI) and Water bodies (MNDWI) have strong negative relationship with Land Surface Temperature (R²= 0.99, 0.95) whereas Barren land (NDBaI) has positive relationship with Land Surface Temperature (R²= 0.96). Finally, we recommend the decision makers and environmental analyst to emphasis the importance of vegetation cover and water body to minimize the potential impacts of land surface temperature.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

Trace amines are a separate, independent group of biogenic amines, close in structure to classical monoamine neurotransmitters such as dopamine, serotonin and norepinephrine. G protein-coupled Trace Amine-Associated Receptors (TAAR) are mostly investigated for their involvement in the pathogenesis of neuropsychiatric disorders, but expression of TAAR family receptors is observed also in various populations of cells of the immune system. The review is focused on the basic information on the interaction of trace amines and their receptors with cells of the general immune system of humans and other mammals, as well as on data on TAARs role in the function of individual populations of myeloid and lymphoid cells. With further research on the regulatory role of the trace amine system in the pathogenesis of the immune response and determination of the biological mechanisms for their action it would be possible to develop new methods for treating diseases related to immune system dysfunctions.

A comprehensive theory is developed for the chiral optical response of two configurations of the N-oscillator Born-Kuhn model (NOBK): the helically stacked and the corner stacked models. In the helical NOBK model, there is always a chiral response regardless of the value of N, whereas in the corner NOBK, only configurations with even N demonstrate a chiral response. Generally, the magnitudes of optical rotatory dispersion (ORD) and circular dichroism (CD) increase with N when the parameters of each oscillator are fixed. In cases of weak coupling, the spectral shapes of ORD and CD remain invariant, while strong coupling significantly alters the spectral shapes. For large damping, the spectral amplitude becomes smaller, and the spectral features become broader. In the presence of small damping, strong coupling introduces degeneracy in the coupled oscillator system, leading to multiple spectral features in both ORD and CD across the entire spectral region. This simple model not only can help in the design of tunable chiral metamaterials but also enhance our understanding of chiro-optical responses in structures with different configurations.

Comparisons of power flows and efficiencies in two structurally quite similar cylindrical series-parallel planetary gear systems (PGSs) were performed in three separate parts of this paper. Each of these single degree of freedom (DoF) systems consists of three different 2KH subsystems connected in series-parallel. The main goal was to prove that apart from complex, structurally and dynamically coupled PGSs, there are also complex and only structurally coupled PGSs, in which the phenomenon of power flow circulation inside closed loops does not occur. Such a half-coupled type of PGS is herein called pseudo-coupled. Therefore, Part I discusses in detail the geometry, kinematics and statics of coupled PGSs in order to determine power flow paths. A comparison of the directions of power flow in both types of PGSs can be made in Part II after determining the power flow paths in the second planetary gear in a similar way. The directions of power flow in both types of PGSs were determined in a relatively simple way, thanks to the distinction between active and passive torques and thus active and passive shafts of individual subsystems. The efficiency comparison made in Part III will show whether power circulation has an influence on the efficiency value, at least in these two types of PGSs.

Production of electricity using hydro-kinetic tidal turbines has many challenges that must to be overcome to ensure reliable, economic and practical solutions. Energy from flowing water is converted by a system comprising: the turbine rotor blades, a gearbox, an electrical generator, control systems, power electronics, export cables, and a connection to the electricity grid. To date these have often been modelled using simulations of independent systems, lacking bi-directional, real-time, coupling. This approach leads to critical effects being missed. Turbulence in the flow, results in large velocity fluctuations around the blades, causing rapid variation in the shaft torque and generator speed, and consequently in the voltage seen by the power electronics and consequently the export power quality. The resulting poor quality power may be unacceptable to the grid. Conversely, grid frequency and voltage changes can also cause the generator speed to change, resulting in changes to the shaft speed and torque and consequently changes to the lift and drag forces acting on the blades. Clearly, fully integrated, bi-directional, models are needed. Here we present two fully coupled models which use different approaches to model the hydrodynamics of rotor blades. The first model uses Blade Element Momentum Theory (BEMT), resulting in an efficient tool for turbine designers. The second model also uses BEMT combines this with an actuator line model of the blades coupled to an unsteady computational fluid dynamics (CFD) simulation. This simulation, implemented in OpenFOAM, uses an energy balance to compute the shaft speed. Both the BEMT and CFD models are coupled to an Open Modellica model of the electro-mechanical system. Both models have been used to simulate the performance of a 1.2m diameter, scale model, of a three bladed horizontal axis tidal turbine tested in the University of Edinburgh FloWave Ocean Energy Research Facility. The turbulent flow around the blades and the mechanical-electrical variables during the stable period of operation are analysed. Time series and tabulated average values of mechanical thrust, power, torque, and rotational speed as well as electrical variables of generator power, electromagnetic torque, voltage and current are presented for the coupled system simulation. The relationship between the mechanical and electrical variables and the results from both tidal turbine approaches are discussed. Our comparison shows that while the BEMT model provides an effective design tool (leading to slightly more conservative designs), the CFD/BEMT simulations provide more accurate predictions of the blade loads which can be especially important in assessing fatigue on the blades (though at an increased computational cost).

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

In this paper, firstly, some questionable formulas and conceptual oversights of previous reduced sigma set unscented transformation (UT) methods are revised through theoretical analysis. Then the revised UT methods based Kalman filters are used in a GPS/INS tightly-coupled system. The Kalman filter flows are the kind of square-root, since the square-root unscented Kalman filters (SRUKFs) can guarantee the stability of the system. By using the reduced sigma set SRUKFs (which contain simplex sigma set square-root unscented Kalman filter (S-SRUKF), spherical simplex sigma set square-root unscented Kalman filter (SS-SRUKF) and minimum sigma set square-root unscented Kalman filter (M-SRUKF)), the computation cost is greatly saved compared with the standard SRUKF, while the accuracy of the GPS/INS tightly-coupled system still maintained. The structure of the GPS/INS tightly-coupled system is in the form of error state, and the time updates of the state and the state covariance of SRUKFs are directly estimated without using UT, thus the computational time is also greatly saved. The pseudo-satellite is introduced to aid the system when the observation information is deficient, for example, when the GPS signal is deficient in the maneuver environment. By using the pseudo-satellite, the optimal performance of the system is guaranteed. Experiment of unmanned aerial vehicle (UAV) showed that the pseudo-satellite aided mechanism worked well.

Bio-surfactants are surface-active molecules which are produced by the wide range of microbes including bacteria, fungi, and yeast. This study was conducted to identify bio-surfactants by Bacillus subtilis combined with use of cheap substrates and industrial wastes (Mustard cake, Whey and Soya cake) which are found locally in Nepal. Bacillus subtilis, one of the most potential bio-surfactants producer; was isolated from soil sample of hydrocarbon contaminated site. Isolates were grown in a Minimal Salt Media (MSM) with 10% (v/v) mustard oil cake, whey and soya cake separately. The presence and potential of surfactant was determined by the oil spreading technique, emulsification index (%E24) and surface tension measurement. It was revealed that the surface tensions of cell free extract were 54.41, 60.02 and 56.64 mN/m for from mustard cake, whey and soya cake respectively as compared to distilled water (72.09) at 25oC. The emulsification index values are was found to be highest in engine oil from the bio-surfactant extracted from mustard cake, soya cake and whey respectively. Similarly, mustard oil showed the lowest value of emulsification index. The highest emulsification activity was shown in mustard oil i.e. 1.13 from the cell free extract from mustard oil and lowest in engine oil i.e., 0.07, by the extract from soya cake medium, when measured in spectrophotometer at 540 nm. In conclusion, strain of Bacillus subtilis was found to be the potential surface active agent producers on the mustard oil cake, which can be useful medium for various environmental, food and industrial processes.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

Unmanned aerial vehicle (UAV) photogrammetry allows the generation of orthophoto and digital surface model (DSM) rasters of a terrain. However, DSMs of water bodies mapped using this technique often reveal distortions in the water surface, thereby impeding the accurate sampling of water surface elevation (WSE) from DSMs. This study investigates the capability of deep neural networks to accommodate the aforementioned perturbations and effectively estimate WSE from photogrammetric rasters. Convolutional neural networks (CNNs) were employed for this purpose. Two regression approaches utilizing CNNs were explored: direct regression employing an encoder and solution based on prediction of the weight mask by an encoder-decoder architecture, subse-quently used to sample values from the photogrammetric DSM. The dataset employed in this study comprises data collected from five case studies of small lowland streams in Poland and Denmark, consisting of 322 DSM and orthophoto raster samples. Each sample corresponds to a 10 by 10 meter area of the stream channel and adjacent land. A grid search was employed to identify the optimal combination of encoder, mask generation architecture, and batch size among multiple candidates. Solutions were evaluated using two cross-validation methods: stratified k-fold cross-validation, where validation subsets maintained the same proportion of samples from all case studies, and leave-one-case-out cross-validation, where the validation dataset originates entirely from a single case study, and the training set consists of samples from other case studies. The proposed solution was compared with existing methods for measuring WSE in small streams using a drone. The results indicate that the solution outperforms previous photogrammetry-based methods and is second only to the radar-based method, which is considered the most accurate method available. The solution is characterized by a high degree of explainability and generalization.

The aim of this study was to evaluate the emulsification properties of garlic water-soluble compounds (GWSC) after heat treatment (10 min at 95 °C) or pH adjustments (2.5, 3.5 and 7.8). After the various treatments, the extracts were used as such or filtrated (0.45 µm) and 10% soybean oil-in-water emulsions were prepared using low (0.48%) or high (6.55% wt/wt) extract concentrations. Whereas at low GWSC concentration, both heating or acidifying resulted in the formation of bigger oil droplet sizes (i.e. from d32=0.36 µm using unmodified extract, to d32=7–22 µm µm at pH 2.5 with or without extract filtration), the effects were opposite at the highest GWSC concentration. In the latter, heat treatment clearly reduced the droplet size as observed from the micrographs as well as the degree of creaming, though the occurrence of depletion and/or bridging flocculation was still strong. The acidification of the extract at this high GWSC concentration, significantly reduced the droplet size as observed from the micrographs but a strong flocculation was observed. Removal of protein aggregates, and possibly also saponin micelles from the extract, resulted in an obvious increase in emulsion droplet size. This research brings valuable insights on the study and utilisation of novel natural food emulsifiers from plant sources.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p > 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

The article presents a new method called slide roller burnishing (SRB) for cold working of cylindrical surfaces on machine tools, implemented with a novel multi-functional device. The machined material was chromium–nickel austenitic stainless steel. The deforming element is a toroidal roller whose axis crosses that of the workpiece. As a result, a relative sliding velocity occurs in the contact zone between the roller and the machined surface. The sliding velocity vector is set using the burnishing device. The theoretical background of SRB is presented. When the two axes are parallel, the well-known roller burnishing (RB) method is implemented. Thus, RB is a special case of SRB. Both processes are realized using the multi-functional burnishing device. The RB process was studied experimentally and optimized according to three criteria, based on the relationship between the surface integrity and operating behavio of the respective component, to achieve three processes: smoothing, hardening and mixed burnishing. Using the optimal RB parameters obtained, the dependence of the results of SRB on the crossing angle was investigated and optimized. A comparative analysis was performed between the optimized RB and SRB processes (respectively for their three variants: smoothing, hardening and mixed) based on geometrical and physical–mechanical characteristics of the surface integrity. The main advantage of the SRB is that it provides smaller height roughness parameters and a higher surface microhardness than RB.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

Microencapsulation by atomization can be used to minimize the loss of bioactive compounds, improving the characteristics and applicability of the powdered product. This study evaluates the effect of different encapsulating agents (maltodextrin, gum arabic, and chitosan) and three spray nozzle diameters (1.0, 1.2, and 1.5 mm) on the atomization of guavira (Campomanesia adamantium) pulp with added 6% bocaiuva (Acrocomia aculeata) dehydrated pulp in the green maturation stage. The experiment followed a simplex-centroid mixed design, with carrier agent concentrations and spray nozzle diameters as independent variables and powder yield, solubility, hygroscopicity, and vitamin C content as dependent variables. The results show that gum arabica increased powder yield and vitamin C retention. The addition of maltodextrin resulted in powders with increased solubility and low hygroscopicity. Furthermore, the optimization tool indicated that the best process conditions were achieved with the addition of gum arabic (10.8%) and chitosan (7.2%), resulting in powders with 29.48% yield, 82.96% solubility, 15.90% hygroscopicity and 741.11 mg/100g vitamin C. Furthermore, the 1.0 mm diameter spray nozzle was considered the most suitable for obtaining guavira pulp microparticles with higher ascorbic acid content.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Pollution of urban surface dust with hazardous elements (HEs) is a serious environmental issue due to its toxicity and potential hazardous effects. Surface dust samples were collected from core urban, urban, and suburban gradients in the Urumqi city of the arid NW China, and the concentrations of six HEs, such as arsenic (As), cadmium (Cd), nickel (Ni), lead (Pb), mercury (Hg), and chromium (Cr), were determined. The pollution load index (PLI) and the US EPA health risk assessment model were applied to analyze and compare the pollution levels and potential health risk of HEs in surface dusts in different urbanization gradients. The obtained results indicate that the average concentrations of Hg, Cd, and Ni in surface dust decrease in the order of core urban > urban > suburban, whereas the average concentrations of As, Cr, and Pb decrease in the order of urban > core urban > suburban. The PLI of HEs in surface dust decreased in the order of core urban > urban > suburban. The concentrations of HEs in the core urban and urban gradients are relatively higher than in the suburban gradient. Furthermore, the total non-carcinogenic and carcinogenic risk index of investigated HEs in surface dust decrease in order of urban > core urban > suburban, for both adults and children. In addition, the pollution of surface dust with HEs in all urbanization gradients is more harmful to the children's health than to the adults. Overall, the potential non-carcinogenic and carcinogenic health risks of the investigated HEs, instigated primarily by oral ingestion of surface dust, are found to be within the acceptable range. However, urbanization can effects the accumulation of HEs in surface dust, and Cr is the main non-carcinogenic risk factor, whereas Cd is the main carcinogenic risk factor among the analyzed HEs in surface dust in all urbanization gradients.

The synthesis 2-tert-butyl-4-methylphenol is of great significance because of its widely application in industry, and the development of highly efficient catalyst is necessary to the alkylation of p-cresol and tert-butyl alcohol. Here, an efficient and mild method was established, caprolactam was chosen as hydrogen-bonding acceptor, p-toluenesulfonic acid was employed as hydrogen-bonding donor, and deep eutectic solvent (DES) was prepared to catalyze the alkylation reaction. The structure of the DES catalyst was characterized by 1H NMR spectra, thermogravimetric analysis and fourier transform infrared spectra (FT-IR). In addition, response surface design based on Box-Behnken method was employed to optimize the alkylation reaction process parameters, the study of reaction kinetics was also carried out subsequently. The recycle performance of the catalyst was evaluated by recovery experiments, and a good result was obtained. Comparing with the literature reported, we here provide a mild method to the synthesis of 2-tert-butyl-4-methylphenol.

Mapping and prediction of inundated areas is increasingly important for climate change adaptation and emergency preparedness. Flood forecasting tools and flood risk models have to be compared to observed flooding patterns for training, calibration, validation and benchmarking. At regional to continental scale, satellite earth observation is the established method for surface water extent (SWE) mapping and several operational global-scale data products are available. However, the spatial resolution of satellite-derived SWE maps remains a limiting factor, especially in low-lying areas with complex hydrography, such as Denmark. We collected thermal imagery using an unmanned airborne system (UAS) for three areas in Denmark shortly after major flooding events. We combined the thermal imagery with an airborne lidar-derived high-resolution digital surface model of the country to retrieve high-resolution (40 cm) SWE maps. The resulting SWE maps were compared to low-resolution SWE maps derived from satellite earth observation (EO). We conclude that UAS have significant potential for SWE mapping at intermediate scales, can bridge the scale gap between ground observations and satellite EO and can be used to benchmark and validate SWE mapping products derived from satellite EO as well as models predicting inundation.

Climate and land use changes are two factors affecting the hydrology of watersheds. The greatest effect of climate change is probably the change in the hydrological cycle, thus water availability for human consumption, industry, and power generation. While the change in land use can cause changes in the hydrological components of the basin, such as evapotranspiration, runoff, and groundwater recharge. From these projections, it is necessary to understand the processes involved in climate change and land use and its impact on water systems. In this context, the objective of this study was to simulate climate change scenarios combined with the land use change and to analyze the impacts on the hydrology in the Piracicaba basin. Two periods were selected based on the preliminary result of detection of the abrupt change point of the annual flow series, using Petitt's non-parameter test. The first period selected prior to the occurrence of the point of the change was from 1985 to 2000. The other period after the point of the change was 2001 to 2015. Land use maps of the years 1990 and 2010 were used to represent the two periods. The results showed a good performance of the SWAT model. The NS (Nash-Sutcliffe coefficient) was 0.88 in calibration for both periods. In the validation, the NS was 0.92 and 0.94 for the first and second periods respectively. We then simulate climate and land use changes scenarios and compare them to the current scenario (baseline). The simulation results showed that the hydrological processes in the Piracicaba basin in the period 1985-2015, had more intense responses to land use change than climate.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Increased CO2 emissions and air pollution impact the environment and human health. In this manner, new functionalized polyaminal-based polymers are synthesized via a one-pot polycondensation reaction of melamine with aldehyde monomers 2-bromo-1-naphthaldehyde and 2-hydroxy-1-naphthaldehyde to yield bromine- hydroxyl- functionalized polymer networks PAN-BrNA and PAN-HNA, respectively. The polyaminals porosity parameters were investigated and applied as an adsorbent for CO2 capture. FTIR, solid-state 13C NMR, and X-ray diffraction verified the PANs structure development. A scanning electron microscope and N2 adsorption-desorption methods were utilized to identify the porous properties of the polymers at 77 K. The Brunauer-Emmett-Teller (BET) surface area of PAN-BrNA and PAN-HNA is (16.6990 m2/g) and (716.7568 m2/g), respectively. At 273 K, PAN-BrNA and PAN-HNA can take CO2 gas up to (4.42786 cm3/g) and (47.55 cm3/g), respectively. The findings show that inserting functional groups has a significant impact on surface area and porosity parameters, as well as CO2 uptake.

The controllability and consistency in the fabrication of micro-textures on large-scale remains a challenge for existing production processes. Mask electrolyte jet machining (MEJM) is an alternative to Jet-ECM for controllable and high-throughput surface microfabrication with more consistency of dimensional tolerances. This hybrid configuration combines the high-throughput of masked-ECM and the adjustable flow-field of jet-ECM. In this work, a duckbill jet nozzle was introduced to make MEJM more capable of batch micro-structuring. A multiphysics model was built to simulate the distribution of electrochemical reaction ions, the cur- rent density distribution and the evolution of the shape of the machined cavity. Experimental investigations are presented showing the influence of the machining voltage and nozzle moving speed on the micro cavity. Several 35 ×35 micro cavity arrays with a diameter of 24.92 − 11.73 µm and depth of 15.86 − 7.24 µm are generated on 304 stainless steel.

This study aimed to compare the flexural strength, surface roughness, and microhardness of a resin for three-dimensional (3D) printing and a conventional composite resin and to evaluate whether the printing orientation influences these properties. To evaluate the flexural resistance, test specimens were produced and divided into four groups: three groups of resins for 3D printing with inclinations of 0°, 45°, and 90°, and one group of conventional composite resin. Forty discs were produced and subjected to a sandpaper-polishing sequence, and the surface roughness was measured using a roughness meter. The Vickers microhardness test was performed at three different points, and the average was obtained. The results were subjected to ANOVA statistical analysis and Tukey's test. There were statistical differences in the flexural strength and microhardness between the conventional resin and the resin used for 3D printing. No statistical difference in surface roughness was observed. The resin for 3D printing exhibited lower flexural strength and microhardness than conventional composite resins. We concluded that the resin for 3D printing had lower flexural strength and hardness than the conventional composite resin but similar surface roughness. The printing orientation did not affect the flexural strength, whereas the hardness increased as the printing angle increased.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

Intrinsically disordered proteins mediate crucial biological functions through their interactions with other proteins. Mutual synergistic folding (MSF) occurs when all interacting proteins are disordered, folding into a stable structure in the course of the complex formation. In these cases, the folding and binding processes occur in parallel, lending the resulting structures uniquely heterogeneous features. Currently there are no dedicated classification approaches that would take into account the particular biological and biophysical properties of MSF complexes. Here we present a scalable clustering-based classification scheme, built on redundancy-filtered features that describe the sequence and structure properties of the complexes, and the role of the interaction, which is directly responsible for structure formation. Using this approach, we define six major types of MSF complexes, corresponding to biologically meaningful groups. Hence, the presented method also shows that differences in binding strength, subcellular localization, and regulation are encoded in the sequence and structural properties of proteins. While current structure classification methods can also handle complex structures, we show that the developed scheme is fundamentally different, and since it takes into account defining features of MSF complexes, it serves as a better representation of structures arising through this specific interaction mode.

In this work, the wetting and evaporation behaviour of non-polar solvent droplets on thin soluble coatings is investigated experimentally. The wetting process on spin coated polymer layers by the solvent is captured using shadowgraphy. Initial spontaneous dynamic wetting as well as later stages of wetting are recorded and evaluated. Furthermore, structures obtained by wetting and subsequent evaporation of solvents on polymer coatings are studied by confocal microscopy. The solubility of the substrate has been varied by using polymers with different molecular masses. We observe that initial spreading dynamics does not depend on the molar mass in the studied range. However, we find a strong influence of the molar mass on the late stage wetting dynamics and on the surface structure after solvent evaporation.

MIPs inspired by antigen-antibody interactions have received substantial interest as a biomimetic artificial receptor system in environmental applications. Herein, we present a molecularly imprinted surface plasmon resonance (SPR) sensor integrated with Au nanoparticles for the identification of bisphenol A (BPA), an endocrine-disrupting chemical. The synthetic wastewater samples were analyzed to ensure the method's reliability and feasibility. Under ideal conditions, the suggested approach performed well in terms of analytical performance to BPA, with a wide linear range of 0.1 to 10 ppb and LOD of 10 ng/L. The sensor results and the Langmuir adsorption model have good agreement. It has also been shown that repeated use of the biosensor can be achieved. According to selectivity studies, BPA adsorbed within the imprinted cavities favorably compared to 4-nitrophenol and phenol. The produced BPA-imprinted SPR sensor provides improved sensitivity based on the signal amplification strategy, unconjugated sensing without the need for labeling, real-time sensing, low sample consumption rates, quantifiable assessment, and very good kinetic rate constant calculation in actual samples. Also, because the produced sensor is reusable with relative standard deviations (RSD)<1.25, indicating the sensor's accuracy, the SPR-based biomimetic BPA sensor is simple to practice and may be an economical option.

Taking a typical forest underlying surface as the research area, this study employed the unmanned aerial vehicle (UAV) photogrammetry to explore more accurate canopy parameters including tree height and canopy radius, which were used to improve the Noah-MP land surface model conducted in Dinghushan Forest Ecosystem Research Station (CN-Din). While the canopy radius was fitted as a Burr distribution, the canopy height of CN-Din forest followed a Weibull distribution. The replacement of the parameters by these observed UAV would result in the Noah-MP model. It was found that the influence on the simulation of the energy fluxes could not be negligible, and the main influence of these canopy parameters was on the latent heat flux which could decrease up to -11% in the midday while increase up to 15% in the nighttime. Additionally, this work indicated that the description of the canopy characteristics for the land surface model should be improved to accurately deliver the heterogeneity for the underlying surface.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

Once on Mars, maintenance and repair will be crucial for humans as supply chains including Earth andMars will be very complex. Consequently, the raw material available on mars must be processed and used. Factors such as the energy available for material production play just as important a role as the quality of the material that can be produced and the quality of its surface. With the aim of developing and technically implementing a process chain that meets the challenge of producing spare parts from oxygen-reduced Mars regolith, this paper addresses the issue of low-energy handling. Expected statistically distributed high roughnesses of sintered regolith analogs are approximated in this work by parameter variation in the PBF-LB/M process. For low-energy handling, a dry-adhesive microstructure is used. Investigations are carried out to determine the extent to which the rough surface resulting from the manufacturing process can be smoothed by deep rolling in such a way that the microstructure adheres and enables samples to be transported. For the investigated AlSi10Mg samples (12 mm x 12 mm x 10 mm), the surface roughness varies in a wide range from Sa 7.7 µm to Sa 64 µm after the additive manufacturing process, pull-off stresses of up to 6.99 N/cm² could be realized after deep rolling. This represents an increase in pull-off stresses by a factor of 392.94 compared to the pull-off stresses before deep rolling, enabling handling of even larger specimens. It is noteworthy that specimens with roughness values that were previously difficult to handle can be treated post-deep rolling, indicating a potential influence of additional variables that describe roughness or ripples and are associated with the adhesion effect of the microstructure of the dry adhesive.

High surface area carbon was obtained from -carrageenan – urea cryogels doped with 1.25 – 5 wt% graphene oxide (GO). Incorporation of GO resulted in multifaceted modification in the textural and chemical properties of the carbon cryogel. The thermal decomposition of GO facilitated the formation of micropores resulted in a substantial increase in the apparent surface area (up to 1780 m2/g). The annealing at 1000 °C removed part of the heteroatoms but left behind a high number of defects. While the volatile thermal degradation products of GO affected the porous texture and the surface chemistry in a complex way, its reduced residue resulted in a gradually increasing electrical conductivity. The influence of GO was studied in oxygen reduction reaction (ORR) and in Li-ion storage application. GO affected the electron transfer mechanism in the ORR tests and challenged the stability of the electrodes. Even if the electrode has been stabilized under oxygen-free conditions, later may undergo destabilization processes during the ORR. The 5 wt% GO doped sample was the most sensitive under oxidative conditions, but finally it exhibited the highest capacitance. In the Li-ion battery tests the coulombic efficiency of all the samples was consistently above 98 %, indicating the great potential of such carbons for efficient Li-ion insertion and reinsertion during the charge – discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25% sample showed an initial discharge capacity of 313 mAh/g, 95.1 % capacity retention and 99.3 % coulombic efficiency after 50 charge – discharge cycles.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

The objective of this study is to evaluate the effects of the 3D point cloud density derived from unmanned aerial vehicle (UAV) photogrammetry and structure from motion (SfM) and multi-view stereopsis (MVS) techniques, the interpolation method for generating a digital terrain model (DTM), and the resolution (grid size) of the derived DTM on the accuracy of estimated heights in small areas, where a very accurate high spatial resolution is required. A UAV-photogrammetry project was carried out on a bare soil of 13 × 13 m with a rotatory wing UAV at 10 m flight altitude (equivalent ground sample distance = 0.4 cm). The 3D point cloud was derived, and five sample replications representing 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50, 60, 70, 80 and 90% of the original cloud were extracted to analyze the effect of cloud density on DTM accuracy. For each of these samples, DTMs were derived using four different interpolation methods (Inverse Distance Weighted (IDW), Multiquadric Radial Basis Function (MRBF), Kriging (KR), and Triangulation with Linear Interpolation (TLI)) and 15 DTM grid size (GS) values (20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0.67, 0.5, and 0.4 cm). Then, 675 DTMs were analyzed. The results showed, for each interpolation method and each density, an optimal GS value (most of the cases equal to 1 cm) for which the Root Mean Square Error (RMSE) is minimum. IDW was the interpolator which yielded best accuracies for all combination of densities and GS. Its RMSE, considering the raw cloud, was 1.054 cm. The RMSE increased 3% when a point cloud with 80% extracted from the raw cloud was used to generate the DTM. When the point cloud included the 40% of the raw cloud, RMSE increased 5%. For densities lower than 15%, RMSE increased exponentially (45% for 1% of raw cloud). The grid size minimizing RMSE for densities of 20% or higher was 1 cm, which represents 2.5 times the ground sample distance of the pictures used for developing the photogrammetry project.

In the present study, Electrocoagulated Metal Hydroxide Sludge (EMHS) was analyzed as adsorbent material to remove both fluoride ion (F-) and arsenic V (As(V)) from aqueous effluents. This material was generated during an electrocoagulation process using Aluminum anode. It was characterized by using specific surface areas and the surface morphology was studied by scanning electron microscopy (SEM). Adsorbent fixed-beds are generally studied to remove different class of contaminants. EMHS was evaluated using a continuous flow rate column test with an experimental design. The effect of initial concentration of F- (2.5–10 mg L⁻¹) and the Empty Bed Contact Time (EBCT (0.4–0.8 min)) was studied following a central composite design methodology. The experimented parameters had a significant influence on saturation time, breakthrough volume, and breakthrough time. A response surface analysis was a tool for analyzing the adsorption study, showing interactions that are complicated to identify by others methods. The results, here reported, revealed that EMHS is an efficient and promising adsorbent material in order to remove F- and As(V) from water contaminated by these pollutants.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

This study was conducted to investigate heavy metal contamination and potential health risk of ground water of selected municipal solid waste (MSW) disposal sites of Khyber Pakhtunkhwa (KP) Pakistan. For this purpose a total of 30 composite samples of both surface and ground water were collected from dumpsites of Abbottabad, Bannu and Peshawar. The collected samples were analyzed for physico-chemical parameters and heavy metals by following standard methods. Results indicated that pH values were found within the acceptable limits specified by national environmental quality standards (NEQS) and world health organization (WHO). Mean concentrations of heavy metals were within NEQS and WHO limits, except for Ni which exceeded the NEQS and WHO limit of 0.02 mg/L in all samples, Similarly, Mn exceeded the limit set by NEQS and WHO (0.5 mg/L) in the ground water samples collected from Bannu dumpsite. The multivariate analysis indicated that the heavy metal contamination of the groundwater of the selected dumpsites was anthropogenic. The pollution index (PI) values (PI≥100) of Mn and Ni indicated very high pollution at individual levels while collectively based on heavy metals pollution index (HPI) values (HPI ≥ 200) the ground water of all the selected dumpsites were found highly polluted. Whereas, the hazard index (HI) values (HI ≥ 5) suggested adverse health effects. It was concluded that the ground water of all the dumpsites was highly polluted with heavy metals particularly Ni and Mn thus, posing a high health risk.

Land surface albedo determines the splitting of downwelling solar radiation into components which are either reflected back to the atmosphere or absorbed by the surface. Land surface albedo is an important variable for the climate community and therefore was defined by the Global Climate Observing System (GCOS) as an Essential Climate Variable (ECV). Within the scope of the Satellite Application Facility for Land Surface Analysis (LSA SAF) of EUMETSAT, a near-real time (NRT) daily albedo product was developed in the last decade from observations provided by the SEVIRI instrument on board the geostationary satellites of the Meteosat Second Generation (MSG) series. In this study we present a new collection of albedo satellite products based on the same satellite data. The MSG Ten-day ALbedo (MTAL) product incorporates MSG observations over 31 days with a frequency of NRT production of 10 days. The MTAL collection is more dedicated to climate analysis studies compared to the daily albedo that was initially designed for the weather prediction community. For this reason, a homogeneous reprocessing of MTAL was done in 2018 to generate a Climate Data Record (CDR). The resulting product is called MTAL-R and has been made available to the community in addition to the NRT version of the MTAL product which has been available for several years. The retrieval algorithm behind the MTAL products comprises three distinct modules: one for atmospheric correction, one for daily inversion of a semi-empirical model of the bidirectional reflectance distribution function, and one for monthly composition that also determines surface albedo values. In this study the MTAL-R CDR is compared to ground surface measurements and concomitant albedo products collected by sensors on-board polar-orbiting satellites (SPOT-VGT and MODIS). We show that MTAL-R meets the quality requirements if MODIS or SPOT-VGT are considered as reference. This work leads to 14 years of production of geostationary land surface albedo products with a guaranteed continuity in the LSA SAF for the future years with the forthcoming third generation of European geostationary satellites.

G-protein coupled estrogen receptor (GPER) was described to exerts several cardioprotective effects. However, the exact mechanism involved in cardiac protection remains unclear. The aim of this study is to investigate the role of GPER activation on excitation-contraction coupling (ECC), and the possibility that such effect participates in cardioprotection. Cardiac myocytes of male Wistar rats were isolated with digestive buffer and loaded with Fura-2-AM for measurement of intracellular calcium transients (CaT). Sarcomere shortening (SS) and L-type calcium current (ICaL) were also registered. Confocal technique was used to measure nitric oxide (NO) production in cells loaded with DAF-FM-diacetate. Cardiac myocytes exposed to E2 (10 nM), or G-1 (1 µM) for fifteen minutes decreased CaT, SS and ICaL. These effects were prevented using G-36 (antagonist of GPER, 1 µM), L-Name (NO synthase inhibitor, 100 nM), or wortmannin (phosphoinositide-3-kinase inhibitor, 100 nM). Moreover, G1 increased NO production, and this effect was abolished in the presence of wortmannin. We concluded that the selective activation of GPER with E2 or G1 in isolated cardiac myocytes of male rats induced a negative inotropic effect due to the reduction of ICaL and the decrease in CaT. Finally, the pathway that we proposed to be implicated in these effects is PI3K-NOS-NO.

In order to enhance the gain of antenna suitable for the airplane mounted platform, a conformal tightly coupled antenna array is investigated in this paper. Especially, three-dimensional (3-D) inkjet printing technique is used to implement the conformal property. The printing of antenna substrate and radiation layer is implemented by combining the fused deposition modelling and microdroplet injection molding technologies based on the existing 3-D printer. Here, through a unique combination of 3-D and 2-D inkjet printing of dielectric material and metallic ink, respectively, we demonstrate a monolithically integrated to a nonplanar antenna for the first time. Antenna measurements show that the complete characterization of this new process in terms of minimum feature sizes and achievable conductivities. This antenna configuration offers a high-gain performance with low-cost and rapid fabrication technique by using 3-D printing. The voltage standing wave ratio and radiation patterns are tested after adding the newly designed feed structure. Results shown the design process much efficient. Both antenna element and the array with good properties, which are in very good agreement with the specially mounted platform.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Coalescence of nanowires and other three-dimensional structures into continuous film is desirable for growing low dislocation density III-nitride and III-V materials on lattice-mismatched substrates, and interesting from the fundamental viewpoint. Here, we develop a growth model for vertical nanowires which, under rather general assumptions on the solid-like coalescence process within the Kolmogorov crystallization theory, results in a morphological diagram for the asymptotic coverage of a substrate surface. The coverage is presented as a function of two variables, the material collection efficiency on the top nanowire facet a, and the normalized surface diffusion flux of adatoms from the NW sidewalls b. The full coalescence of nanowires is possible only when a=1 regardless of b. At a&gt;1, which is usual for vapor-liquid-solid growth with a catalyst droplet, nanowires can only partly merge but never coalesce into continuous film. These results can be used for predicting and controlling the degree of surface coverage by nanowires and three-dimensional islands by tuning the surface density, droplet size, adatoms diffusivity, and geometry of the initial structures in the vapor-liquid-solid, selective area or self-induced growth processes in different epitaxy techniques.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

Wetting of deformable substrates has gained significant interest over the past decade due to its extensive applications and uses. This interest has developed due to technological advances which are able to capture interfacial behavior taking place when a liquid droplet is placed on a deformable substrate. Researchers have developed different theories to explain processes taking place in the process of wetting of deformable/soft substrates. For the scope of this review, we will consider the fluid to be Newtonian, partially wetting, and surface forces are incorporated with the help of disjoining/conjoining pressure acting in the vicinity of the apparent, three-phase contact line. The following subjects are briefly reviewed: (i) Equilibrium of droplets on soft substrates. It is shown that properties of the disjoining/conjoining pressure isotherm and properties of the deformable substrate determine both the shape of the liquid droplet and deformation of the substrate; (ii) Equilibrium conditions of droplets on deformable substrates. It is shown that for a droplet to be at equilibrium on a deformable substrate under consideration, Jacobi’s sufficient condition is satisfied; (iii) Hysteresis of contact angle of sessile droplets on deformable substrates. It is shown that as the elasticity of the deformable substrate is increased, both advancing and receding contact angles are reduced.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

This study explores wind energy resources in different locations through the Gulf of Oman and also their future variability due climate change impacts. In this regard, EC-EARTH near-surface wind outputs obtained from CORDEX-MENA simulations are used for historical and future projection of the energy. The ERA5 wind data are employed to assess the suitability of the climate model. Moreover, the ERA5 wave data over the study area are applied to compute sea surface roughness as an important variable for converting near-surface wind speeds to those of wind speed at turbine hub height. Considering the power distribution, bathymetry and distance from the coats, some spots as tentative energy hotspots to provide a detailed assessment of directional and temporal variability and also to investigate climate change impact studies. RCP8.5 is a common climatic scenario is used to project and extract future variation of the energy in the selected sites. The results of this study demonstrate that the selected locations have a suitable potential for wind power turbine plans and constructions.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

Hydrogeological maps must synthesize the scientific knowledge about the hydraulic features and the hydrogeological behavior of a specific area, and, at the same time, they must meet the expectations of land planners and administrators. Thus, especially in complex interconnected systems, hydrogeological maps can be fully effective when they are purpose-designed. In these contexts, usual graphical approaches in creating hydrogeological maps could result uncomplete and/or ineffective. Therefore, in case of complex systems and/or specific management/protection aims, new and purpose-designed graphical solutions must be applied to enhance the maps effectiveness. In the case study, these solutions show and emphasize all the hydraulic interconnections playing significant roles in recharging the multilayered alluvial aquifer, where the majority of wells have been drilled for drinking/industrial/agricultural purposes, artificial channels are used for agricultural purposes, and the shallow groundwater feeds protected groundwater-dependent-ecosystems. The hydrogeological map was then designed to be the synthesis of three different and hydraulically interconnected main contexts: (i) the main heterogeneous alluvial aquifer (the main target of the purpose-designed map), (ii) the hydrographic basin of a losing river that feeds the main alluvial aquifer, and (iii) those hard-rock aquifers (mainly turbiditic and ophiolitic) whose springs feed the same river.

Regional heat capacity change is calculated from the ratio between the addition or subtraction of heat (ΔQ) with the increase or decrease in temperature (ΔT) region. The purpose of this study is to calculate the regional heat capacity change due to the changes of land cover composition with forest, shrubs, oil palm plantation and bare soil using Landsat-5 TM satellite data on 1994, 2000 and 2010. Total area that used on ​​this study is 12971 ha. In 1994-2000, 4 % of forest area and 2% shrubs were increased, followed by additional of biomass forest 4.01 tons/ha and 2.83 tons/ha for shrubs. The increased of forest area and biomass (tons/ha) caused by forest and shrubs growth processing towards climax that added the canopy volume. So that, the regional heat capacity in 1994 amounted 19384 MJC^o-1 increased to 19929 MJC^o-1 in 2000. Data observation for 2000-2010 showed that forest area decreased by 66% due to forest’s clearing into oil palm plantations (47%), shrubs (8%) and bare soil (11%). But, plant’s biomass continue to increased, i.e 1.48 ton/ha for forest, 2.73 tons/ha for shrubs and 4.63 tons/ha for bare soil. Before 2000, there was no land cover by oil palm plantations, so the increasing rate from this land was the biggest than the three other lands, amounting to 122.29 tons/ha. Decreasing in the percentage of forest area does not cause a decrease in the heat capacity of the region. Intensive maintenance on oil plam plantation such as water management, fertilizer and planting space made it biomass productivity and ability to save the heat is greater than the forest. As the result, in 2010 regional heat capacity increased to 22508 MJC^o-1.

Background: Implant surface topography is a key element in achieving osseointegration. Nanostructured surfaces have shown promising results in accelerating and improving bone healing around dental implants. The main objective of the present clinical and histological study is to compare, at 4 and 6 weeks, (w) bone-to-implant contact in implants having either machined surface (MAC), SLA medium roughness surface or a Nanostructured Calcium-Incorporated sur-face (XPEED®). Methods: 35 mini-implants with 3 different surface treatments (XPEED® (n=16) – SLA (n=13) – Machined (n=6), were placed in the posterior maxilla of 11 patients then, retrieved at either 4 or 6w in a randomized split-mouth study design. Results: The BIC rate measured at 4 and 6w respectively, was: 16.8 % (±5.0) and 29.0 % (±3.1) for MAC surface; 18.5 % (±2.3) and 33.7 % (±3.3) for SLA surface; 22.4 % (±1.3) and 38.6 % (±3.2) for XPEED® surface. In all types of in-vestigated surfaces, the time factor appeared to significantly increase the BIC rate (p < .05). XPEED® surface showed a significantly higher values when compared to both SLA and MAC values at 4w (p < .05). Also, at 6w, both roughened surfaces (SLA and XPEED® ) showed signifi-cantly higher values (p < .05) than turned surface (MAC). Conclusion: Nanostructured Calcium titanate coating is able to enhance bone deposition around implants at early healing stages.

The study of interactions between polyelectrolytes (PE) and surfactants is of great interest for both fundamental and applied research. These mixtures can represent, for example, models of self-assembly and molecular organization in biological systems, but they are also relevant in industrial applications. Amphiphilic block polyelectrolytes represent an interesting class of PE, but their interactions with surfactants have not been extensively explored so far, most studies being restricted to non-associating PE. In this work, interactions between an anionic amphiphilic triblock polyelectrolyte and different types of surfactants bearing respectively negative, positive and no charge, are investigated via surface tension and solution rheology measurements for the first time. It is evidenced that the surfactants have different effects on viscosity and surface tension, depending on their charge type. Micellization of the surfactant is affected by the presence of the polymer in all cases; shear viscosity of polymer solutions decreases in presence of same charge or nonionic surfactants, while the opposite charge surfactant cause precipitation. This study highlights the importance of the charge type, and the role of the associating hydrophobic block in the PE structure, on the solution behavior of the mixtures. Moreover, a possible interaction model is proposed, based on the obtained data.

The detection accuracy of bridge superficial defect using the deep neural network approach decreases significantly under light variation and weak texture condition. To address these issues, an enhanced intelligent detection method based on the YOLOv8 deep neural network is proposed in this study. Firstly, multi-branch coordinate attention (MBCA) is proposed to improve the accuracy of coordinate positioning by introducing a global perception module in coordinate attention mechanism. Furthermore, a deformable convolution based on MBCA is developed to improve the adaptability for complex feature shapes. Lastly, the deformable convolutional network-attention-YOLO (DAC-YOLO) detection algorithm is formed by replacing the deep C2F structure in the YOLOv8 architecture with deformable convolution. A supervised dataset consisting of 4794 bridge surface damage images is employed to verify the proposed method, and results show that it achieves improvements of 2.0% and 3.4% in mAP and R. Meanwhile, the model complexity decreases by 1.2G, increasing the detection speed by 3.5/f·s-1.

Finishing coatings used in the wood-based composites industry play a key role in the final appearance of the finished product. However, the use of such coatings is not only for aesthetic purposes but also to protect the product against surface damage and moisture or minimize the emission of harmful substances. The latter is an extremely important factor in terms of safety for both the manufacturer and the user, which is why the emissivity test is one of the most important tests in the case of finishing coatings. Such a role can be played by carbon-rich materials, such as those remaining from the extraction of birch bark. In this article, an attempt was made to create coatings in the form of a film by combining a biopolymer with suberinic acid residues (SAR). There were two types of biopolymers used – polylactide (PLA) and polycaprolactone (PCL), in various polymer-SAR ratios. SAR as a residue, is a material that bounds CO2 from the atmosphere and creates a possibility of further use. As part of this study, the obtained coatings were tested in terms of resistance to scratch, relative hardness, cold liquids, total volatile organic compounds (TVOC) and formaldehyde emission, surface absorption etc. Differences in the polymers used and the effect of the SAR additive on selected surface properties were demonstrated. The addition of carbon-rich SAR significantly improves the gas barrier properties of the surface finishing materials based on PLA and PCL. The relative hardness and scratch resistance has also increased with raising SAR content. However, the increasing content of SAR filler act as a limiter in the depth of penetration of deposited surface finishing materials onto the wood surface.

Purpose Professional oral hygiene procedures are recommended by dentists, twice a year. BioHPP is a polyetheretherketone polymer used in prosthetic dentistry as a frame material. The aim was to investigate whether routine dental cleaning procedures such as ultrasonic scaling and brushing affect the surface proprieties of prosthetic BioHPP restorations. To evaluate the surface properties of different restorations based on BioHPP (veneered with composite resin and polished) after brushing and ultrasonic scaling exposure. Materials and Methods The 66 BioHPP specimens were divided into three groups (n=22). The first group was the control group, and no further treatment was applied. The specimens in the second group were veneered with composite resin and in the third group the specimens were veneered with composite resin and polished. Each group of samples was divided into 3 subgroups: 0- no treatment, 1-exposed to tooth brushing, 2-exposed to ultrasonic scaling. The surface morphology was investigated by atomic force microscopy (AFM). The structure of samples was analysed using the XRD technique, and the surface wettability was done. Results Control group specimens were significantly rougher compared to other groups (p ≤ 0.05). There was no statistically significant difference in the contact angle of water analyses between the samples. Conclusion: Composite veneered BioHPP showed the highest surface resistance to brushing and ultrasonic scaling.

The advent of graphene opens up the research into two-dimensional (2D) material, which is considered as a revolutionary material in the future. Due to its unique geometric structure, graphene exhibits a series of exotic physical and chemical properties. Besides, single-element-based 2D materials (Xenes) have garnered tremendous interest. At present, 16 kinds of Xenes (silicene, borophene, germanene, phosphorene, tellurene, etc.) have been explored, mainly distributed in the third, fourth, fifth and sixth main groups. The current methods to prepare monolayer or few-layer 2D materials include epitaxy growth, mechanical exfoliation, and liquid phase exfoliation. Although two Xenes (aluminene and indiene) have not been synthesized due to the limitations of synthetic methods or stability of Xenes, other Xenes have been successfully realized by elaborately artificial design and synthesis. Focusing on elemental 2D materials, this review mainly summarizes the recently reported work about tuning the electronic, optical, mechanical, or chemical properties of Xenes via surface modifications achieved by controllable approaches (doping, adsorption, strain, intercalation, phase transition, etc.) to broaden the applications in various fields, including spintronics, electronics, optoelectronics, superconducting, photovoltaics, sensors, catalysis, and biomedicines. These advances in surface modification of Xenes have laid a theoretical and experimental foundation for the development of 2D materials and their practical applications in diverse fields.

Heavy metals are toxic, persistent and non-degradable. After sedimentation and adsorption, they accumulate in water sediments. The aim of this study was to understand the heavy metal pollution of Qinjiang River sediments on the ecological environment and apportioning sources. The mean total concentrations of Mn, Zn, Cr, Cu, and Pb are 3.14, 2.33, 1.39, 5.79, and 1.33 times higher than the background values, respectively, except for the Co, Ni, and Cd, which are lower than the background values; Fe, Co, Ni, Cd, Cr, Cu, and Pb are all primarily in the residual state, while Mn and Zn are primarily in the acid-soluble and oxidizable states, respectively. Igeo, RI, SQGs and RAC together indicate that the pollution status and ecological risk of heavy metals in Qinjiang River sediments are generally moderate; among them, Fe, Co, Ni, Cd, Cr, and Pb are not harmful to the ecological environment of the Qinjiang River. Cu is not readily released because of its higher residual composition, depicting that Cu is less harmful to the ecological environment. Mn and Zn, as the primary pollution factors of the Qinjiang River, are harmful to the ecological environment. This heavy metal pollution in surface sediments of the Qinjiang River primarily comes from manganese and zinc ore mining. Manganese carbonate and its weathered secondary manganese oxide are frequently associated with a significant amount of residual copper and Cd, as a higher pH is suitable for the deposition and enrichment of these heavy metals. Lead-zinc ore and its weathering products form organic compounds with residual Fe, Co, Cr, and Ni, and their content is related to salinity. The risk assessment results of heavy metals in sediments provide an important theoretical basis for the prevention and control of heavy metal pollution in Qinjiang River.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

High frequency knowledge of the spatio-temporal distribution of the Downwelling Surface Shortwave Flux (DSSF) and its diffuse fraction (fd) at the surface is nowadays essential for understanding climate processes at the surface-atmosphere interface, plant photosynthesis and carbon cycle, and for the solar energy sector. The EUMETSAT Satellite Application Facility for Land Surface Analysis operationally delivers estimation of the MDSSFTD (Downwelling Surface Short-wave radiation Fluxes – Total and Diffuse fraction) product with an operational status since the year 2019. The method for the retrieval was presented in the companion paper [40]. The part 2 now focuses on the evaluation of the MDSSFTD algorithm and presents the comparison of the corresponding outputs, i.e. total DSSF and diffuse fraction (fd) components, against in-situ measurements acquired at four BSRN stations over a seven-month period. The validation is performed on an instantaneous basis. We show that the satellite estimates of DSSF and fd meet the target requirements defined by the user community for all-sky (clear and cloudy) conditions. For DSSF, the requirements are 20Wm^-2 for DSSF<200Wm^-2, and 10% for DSSF>=200Wm^-2. The MBE and rMBE compared to the ground measurements are 3.618Wm^-2 and 0.252%, respectively. For fd, the requirements are 0.1 for fd<0.5, and 20% for fd>=0.5. The MBE and rMBE compared to the ground measurements are -0.044 and -17.699%, respectively. The study also provides a separate analysis of the product performances for clear sky and cloudy sky conditions. The importance of representing the cloud-aerosol radiative coupling in the MDSSFTD method is discussed. Finally, it is concluded that the quality of the Aerosol Optical Depth (AOD) forecasts currently available is enough accurate to obtain reliable diffuse solar flux estimates. This quality of AOD forecasts was still a limitation a few years ago.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

In the Mediterranean area, vegetation dynamics and phenology analyzed over a long time can have an important role in highlighting changes in land use and cover as well as the effect of climate change. Over the last 30 years, remote sensing has played an essential role in bringing about these changes thanks to many types of observations and techniques. Satellite images are to be considered an important tool to grasp these dynamics and evaluate them in an inexpensive and multidisciplinary way thanks to Landsat and Sentinel satellite constellations. The integration of these tools holds a dual potential: on one hand, allowing to obtain longer historical series of reflectance data, while on the other hand, making data available with a higher frequency even within a specific timeframe. The study aims to conduct a comprehensive cross-comparison analysis of long-time series pixel values in the Mediterranean regions. For this scope comparisons between Landsat-7 (ETM+), Landsat-8 (OLI), and Sentinel-2 (MSI) satellite sensors were conducted based on surface reflectance products. We evaluated these differences using Ordinary Least Squares (OLS) and Major Axis linear regression (RMA) analysis on points extracted from over 15,000 images across the Mediterranean basin area from 2017 to 2020. Minor but consistent differences were noted, necessitating the formulation of suitable adjustment equations to better align Sentinel-2 reflectance values with those of Landsat-7 or Landsat-8. The results of the analysis are compared with the most used harmonization coefficients proposed in the literature, revealing significant differences. The root mean square deviation, the mean difference and the orthogonal distance regression (ODR) slope show an improvement of the parameters for both models used (OLS and RMA) in this study. The discrepancies in reflectance values lead to corresponding variations in the estimation of biophysical parameters, such as NDVI, showing an increase in the ODR slope of 0.3. Despite differences in spatial, spectral, and temporal characteristics, we demonstrate that integration of these datasets is feasible through the application of band-wise regression corrections for a sensitive and heterogeneous area like those of the Mediterranean basin area.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

The mineralocorticoid hormone aldosterone regulates sodium and potassium homeostasis but also adversely modulates the maladaptive process of cardiac adverse remodeling post-myocardial infarction. Through activation of its mineralocorticoid receptor (MR), a classic steroid hormone receptor/transcription factor, aldosterone promotes inflammation and fibrosis of the heart, the vasculature, and the kidneys. This is why MR antagonists reduce morbidity and mortality of heart disease patients and are part of the mainstay pharmacotherapy of advanced human heart failure. A plethora of animal studies using cell type–specific targeting of the MR gene have established the importance of MR signaling and function in cardiac myocytes, vascular endothelial and smooth muscle cells, renal cells, and macrophages. In terms of its signaling properties, the MR is distinct from nuclear receptors in that it has, in reality, two physiological hormonal agonists: not only aldosterone but also cortisol. In fact, in several tissues, including in the myocardium, cortisol is the primary hormone activating the MR. There is a considerable amount of evidence indicating that the effects of the MR in each tissue expressing it depend on tissue- and ligand-specific engagement of molecular co-regulators that either activate or suppress its transcriptional activity. Identification of these co-regulators for every ligand that interacts with the MR in the heart (and in other tissues) is of utmost importance therapeutically, since it can not only help elucidate fully the pathophysiological ramifications of the cardiac MR`s actions but also help design and develop novel better MR antagonist drugs for heart disease therapy. Among the various proteins the MR interacts with are molecules involved in cardiac G protein-coupled receptor (GPCR) signaling. This results in a significant amount of crosstalk between GPCRs and the MR, which can affect the latter`s activity dramatically in the heart and in other cardiovascular tissues. This review summarizes the current experimental evidence for this GPCR-MR crosstalk in the heart and discusses its pathophysiological implications for cardiac adverse remodeling as well as for heart disease therapy. Novel findings revealing non-conventional roles of GPCR signaling molecules, specifically of GPCR-kinase (GRK)-5, in cardiac MR regulation are also highlighted.

For centuries, humans have relied on natural products to prevent and treat numerous health issues. However, biologically active compounds from natural sources, such as polyphenols, face significant challenges, including low solubility, rapid metabolism, and instability, which hinder their effectiveness. Advances in science and nanotechnology have provided solutions to overcoming these problems through the use of porous silica materials. These materials possess unique properties, such as a high specific surface area, adjustable particle and pore sizes, and a surface that can be easily and selectively modified. In this review, we summarize and discuss findings on how the pore and particle size, structure, and surface modification of silica materials influence the preparation of efficient delivery systems for biologically active polyphenols from natural sources. The available data demonstrate how parameters such as adsorption capacity, release and antioxidant properties, bioavailability, solubility, stability, etc. of the studied delivery systems could be affected by the structural and chemical characteristics of the porous silica carriers.

The beta-galactoside-binding mammalian lectin galectin-1 can bind, via its carbohydrate recognition domain (CRD), various cell surface glycoproteins and has been implicated in a range of cancers. As a consequence of binding to sugar residues on cell surface receptors it has been shown to have a pleiotropic effect across many cell types and mechanisms resulting in immune system modulation and cancer progression. As a result, it has started to become a therapeutic target for both small and large molecules. In previous studies, we have used fluorescence polarisation (FP) assays to determine KD values to screen and triage small molecule glycomimetics that bind to the galectin-1 CRD. In this study surface plasmon resonance (SPR) was used to compare human and mouse galectin-1 affinity measures with FP as SPR has not been applied for compound screening against this galectin. Binding affinities for a selection of mono- and di-saccharides covering a 1,000-fold range correlated well between FP and SPR assay formats for both human and mouse galectin-1. It was shown that slower dissociation drove the increased affinity at human galectin-1 whilst faster association was responsible for the effects at mouse galectin-1. This study demonstrates that SPR is a sound alternative to FP for early drug discovery screening and determining affinity estimates. Consequently, it also allows association and dissociation constants to be measured in a high throughput manner for small molecule galectin-1 inhibitors.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

Validation of satellite sea surface salinity (SSS) products is typically based on comparisons with in-situ measurements at a few meters depth, that are mostly done at a single location and time. The difference in term of spatio-temporal resolution between the in-situ near-surface salinity and the two-dimensional satellite SSS results in a sampling mismatch uncertainty. The Climate Change Initiative (CCI) project has merged SSS from three satellite missions. Using an optimal interpolation, weekly and monthly SSS and their uncertainties are estimated at a 50 km spatial resolution over the global ocean. Over the 2016-2018 period the mean uncertainty on weekly CCI SSS is 0.13, whereas the standard deviation of weekly CCI minus in-situ Argo salinities is 0.24. Using high resolution SSS simulations, we estimate the expected uncertainty due to the CCI versus Argo sampling mismatch. Most of the largest spatial variability of the satellite minus Argo salinity are observed in regions with large mismatch. A quantitative validation is performed by considering the statistical distribution of the CCI minus Argo salinity normalized by the sampling and retrieval uncertainties. This quantity should follow a Gaussian distribution with a standard deviation of 1, if all uncertainty contributions are properly considered. We find that 1) the sampling mismatch can explain most of the observed differences between Argo and CCI data, especially for monthly products and in dynamical regions (river plumes, fronts), 2) overall, the uncertainties are well estimated in CCI version 3, much better compared to CCI version 2. There are a few dynamical regions where discrepancies remain, and where the satellite SSS, their associated uncertainties and the sampling mismatch estimates should be further validated.

Influence of the volute design parameters on the stable operating range and the performance of a centrifugal compressor was investigated experimentally for the following design conditions. The volute casing surface roughness was changed from 0 to 200 µm in five steps and tested. The axial distance between the casing and the diffuser cascades (clearance) was varied in five steps as C/b₂ = 1.2, 2.4%, 3.6%, 4.8%, and 6% relative to the impeller exit width. The radial distance from the impeller blade exit to the diffuser vane inlet in (vaneless space radius) in six steps as C/r₂ = 1.03, 1.05, 1.07, 1.09, 1.11, and 1. 13 relatives to the rotor outlet radius. The volute outlet geometry of a symmetric and tangent with different area ratios from 0.4 to 0.9. Finally, the compressor has been tested experimentally with different pinched vaned diffuser distances relative to the impeller exit width of bp/b2 =1, 0.98, 0.96, 0.94, 0.92, and 0.9. These testes were carried at different compressor operating conditions, and the time variations of the static pressure were recorded using five high-frequency response pressure transducers. A hot-wire anemometer is used to measure the compressor flow rate. The rotating stall and surge at the vaneless zone after the impeller exit can be detected by analyzing the fluctuations of pressure signals and the power spectrum density by using the Fast Fourier Transformation analysis. The experimental results indicated that the compressor with volute casing surface roughness of 100mm gives about 10.9% enhancements in the stable operating and 1% in pressure rise coefficient. The best axial distance between the diffuser vanes and the casing is 2.4% of the impeller blade height and the compressor in this design gives about 12.4% improvements in the stable working range. The compressor with radial vaneless distance of 1.056 gives improvements of about 16.6% in the surge margin, 2% in the pressure recovery and 4% in pressure rise coefficients. The compressor with a pinched diffuser of b/bp of 0.98 gives an improvement of 20.8% in surge point.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

The rock strata movement deformation generated by the mining process of the mine will inevitably lead to surface subsidence and a series of environmental hazards, so it is particularly important to monitor the rock strata movement deformation and surface subsidence in the goaf area. With the development of surface subsidence monitoring technology, InSAR technology has been widely used in the research of surface subsidence in mining areas with the advantages of high precision and wide monitoring. In this paper, by obtaining the image data of 59 Sentinel-1A scenes in the mining area, the obtained PS points were analyzed and processed by ArcGIS difference analysis by PS-InSAR technology, and the surface deformation cloud map and settlement curve of the mining area in various periods were obtained, and the rock strata movement deformation and surface subsidence law of the goaf before treatment and after different treatment methods were studied by influencing factors such as stope layout and mining depth. The results show that the rock strata movement deformation and surface subsidence degree of the goaf under different treatment methods are different due to different influencing factors, and their positions also change dynamically with time. Applying InSAR technology to study rock strata movement deformation and surface subsidence can provide an important basis for mine safety mining, goaf treatment, rock strata movement deformation and surface subsidence monitoring.

Due to the fact that abrasive media can deform flexibly in abrasive flow machining (AFM) making this method easily to polish the complex holes and the curved surface of the hard machining shapes. Although abrasive media dominate the polishing behavior in AFM process, the mechanism of the abrasive media are not easy to understand because of the high viscous gels, therefore, many finishing works need lots of time to design AFM process. Power laws of the abrasive gels is studied here to evaluate the non-Newtonian flow of abrasive gels in complex holes polishing firstly, at the mean time different abrasive gels are utilized to finish the complex holes to follow the results by non-Newtonian flow calculation. Moreover, traditional AFM has difficulty to achieve a uniform roughness of radial distribution in the complex holes polishing because of the non-uniform abrasive forces. So a helical passageway is proposed to create a multiple motion of abrasive medium and to obtain the even surface of the complex holes in AFM process.

Image-guided radiotherapy supported by surface guidance can help track lower lung lesion respiratory motion while reducing a patient’s exposure to ionizing radiation. However, it is not always clear how skin respiratory motion magnitudes and correlations with lung lesion respiratory motion vary between different skin regions of interest (ROI). Four-dimensional Computed Tomography (4DCT) images provide information on both skin and lung respiratory motion and are routinely acquired for the purpose of treatment planning in our institution. Analysis of 4DCT images for 57 patients treated in our institution has been conducted to provide information on respiratory motion magnitudes of nine skin ROIs of the torso, a tracking structure (TS) representing lower lung lobe lesion, as well as respiratory motion correlations between nine ROIs and TS. The effects of gender and adipose tissue volume and distribution on these correlations and magnitudes have been analyzed. Significant differences between ROIs in both respiratory motion magnitudes and correlations to TS have been detected. An overall negative correlation between ROI respiratory magnitudes and the adipose tissue has been detected for ROIs with rib cage support. A weak to moderate negative correlation between adipose tissue volume and ROI-to-TS respiratory correlations has been detected for upper thorax ROIs. Respiratory magnitudes in regions without rib support tended to be larger for men than for women, but no differences in ROI-to-TS correlation between sexes have been detected. Described findings should be considered when choosing skin surrogates for lower lung lesion motion management.

In this article, the research team has systematically developed a method to model the kinematics and dynamics of a 3-wheeled robot subjected to external disturbances and sideways wheel sliding. These models will be used to design control laws that compensate for wheel slippage, model uncertainties, and external disturbances. These are control algorithms developed based on Dynamic Surface Control (DSC). Adaptive trajectory tracking DSC algorithm using fuzzy logic system (AFDSC) and radial neural network (RBFNN) with fuzzy logic system to overcome the disadvantages of DSC and expand the application domain for wheeled Mobile Robots (WMR). However, this Adaptive Fuzzy Neural Network Dynamic Surface Control (AFNNDSC) adaptive controller ensures the closed system is stable and follows the preset trajectory in the presence of wheel slippage model uncertainty and is affected by significant amplitude disturbances. The stability and convergence of the closed-loop system are guaranteed based on the Lyapunov analysis. The AFNNDSC adaptive controller is evaluated by simulation on MATLAB/Simulink software and in a steady state. The maximum position error on the right wheel and left wheel is 0.000572 (m) and 0.000523 (m), and the angular velocity tracking error in the right and left wheels of the control method is 0.000394 (rad/s). The experimental results show the correctness of the theoretical analysis, the effectiveness of the proposed controller, and the possibility of practical application.