In urban areas, deep excavation-induced ground deformation may damage adjacent existing structures and is conventionally evaluated by levelling at installed settlement points. However, a small number of measurements cannot represent the total change in ground deformation adjacent to excavation sites. Furthermore, significant local subsidence may occur in places where settlement points have not been installed and only noticed after an accident. For deep excavation sites located in urban areas, paved pedestrian sidewalks are often located adjacent to sites, and construction activity can cause these paving blocks to displace. This study introduces a method to detect paving block displacement adjacent to deep excavation sites using terrestrial photogrammetry. A digital camera creating point cloud data (PCD) and an acquisition method satisfying the frontal and side overlap requirements were demonstrated. To investigate the displacement detection and measurement capabilities by PCD analysis, an experimental program was conducted, including a PCD comparison containing the uplift, settlement, and horizontal paving block displacement and reference data. The cloud-to-cloud distance computation algorithm was adopted for PCD comparison. Paving block displacement was detected for displacements of 5, 7.5, and 10 mm in the uplift, settlement, and horizontal directions; however, the horizontal displacements were less clear. PCD analysis enabled satisfactory measurements between 0.024 and 0.881 mm for the vertical-displacement cases, but a significant error was observed for the horizontal-displacement cases owing to the cloud-comparison algorithm. The measurement blind spot of limited settlement points was overcome by the proposed method that detected and measured paving block displacement adjacent to excavation sites.

Traditional camera sensors rely on human eyes for observation. However, the human eye 1 is prone to fatigue when observing targets of different sizes for a long time in complex scenes, and 2 human cognition is limited, which often leads to judgment errors and greatly reduces the efficiency. 3 Target recognition technology is an important technology to judge the target category in camera 4 sensor. In order to solve this problem, a small size target detection algorithm for special scenarios was 5 proposed by this paper. Its advantage is that this algorithm not only has higher precision for small 6 size target detection, but also can ensure that the detection accuracy of each size is not lower than the 7 existing algorithm. In this paper, a new down-sampling method was proposed, which could better 8 preserve the context feature information. The feature fusion network was improved to effectively 9 combine shallow information and deep information. A new network structure was proposed to 10 effectively improve the detection accuracy of the model. In terms of accuracy, it is better than: YOLOX, 11 YOLOXR, YOLOv3, scaled YOLOv5, YOLOv7-Tiny and YOLOv8.Three authoritative public data sets 12 were used in this experiment: a) On Visdron data sets (small size targets), DC-YOLOv8 is 2.5% more 13 accurate than YOLOv8. b) On Tinyperson data sets (minimal size targets), DC-YOLOv8 is 1% more 14 accurate than YOLOv8. c) On PASCAL VOC2007 data sets (Normal size target), DC-YOLOv8 is 0.5% 15 more accurate than YOLOv8.

In the field of vision-based robot grasping, effectively leveraging RGB and depth information to accurately determine the position and pose of a target is a critical issue. To address this challenge, we propose a tri-stream cross-modal fusion architecture for 2-DoF visual grasp detection. This architecture facilitates the interaction of RGB and depth bilateral information and is designed to efficiently aggregate multiscale information. Our novel modal interaction module (MIM) with spatial-wise cross-attention algorithm adaptively captures cross-modal feature information. Meanwhile, the channel interaction modules (CIM) further enhance the aggregation of different modal streams. In addition, we efficiently aggregate global multiscale information through a hierarchical structure with skipping connections. To evaluate the performance of our proposed method, we conduct validation experiments on standard public datasets and real robot grasping experiments. We achieve the image-wise detection accuracy of 99.4% and 96.7% on Cornell and Jacquard datasets respectively. The object-wise detection accuracy reaches 97.8% and 94.6% on the same datasets. Furthermore, physical experiments using the 6-DoF Elite robot demonstrate a success rate of 94.5%. These experiments highlight the superior accuracy of our proposed method.

Pulsed thermography is a vital technique in the nondestructive evaluation field. However, its data analysis can be complex and requires skilled experts. Advances in deep learning have yielded exceptional results, including image segmentation. Therefore, many efforts have been made to apply deep learning methods to data processing for nondestructive evaluation. Despite this, there is currently no public Pulsed thermographic dataset available for evaluating various spatial-temporal deep methods of segmenting pulsed thermographic data. This article aims to provide such a dataset and assess the performance of commonly used deep learning-based instance segmentation models on it. Additionally, the impact of the number of frames and data transformations on model performance is examined. The findings suggest that suitable preprocessing methods can effectively reduce the data size without compromising the deep models’ performance.

Machine learning methods have widely been applied to detect anomalies in machine and cutting tool behavior during lathe or milling. However, detecting anomalies in the workpiece itself did not get the same attention by researchers. That is why in this article, the authors present a pub-licly available multivariate time series dataset which was recorded during milling of 16MnCr5. Due to artificially introduced, though realistic anomalies in the workpiece the dataset can be ap-plied for anomaly detection. By using a convolutional autoencoder as a first model good results in detecting the location of the anomalies in the workpiece were achieved. Furthermore, milling tools with two different diameters where used which led to a dataset eligible for transfer learn-ing. The objective of this article is to provide researchers with a real-world time series dataset of the milling process which is suitable for modern machine learning research topics like anomaly detection and transfer learning.

Brain tumors are abnormal cells growth in the brain tissues that can be cancerous, or not. In any case, they could be a very aggressive disease that should be detected as early as possible. Usually, magnetic resonance imaging (MRI) is the main tool commonly adopted by neurologists and radiologists to identify and classify any possible anomalies present in the brain anatomy. In the present work, an automatic unsupervised method called Z2-$\gamma$, based on the use of adaptive finite-elements and suitable pre-processing and post-processing techniques, is introduced. In particular, the proposed methodology is able to automatically classify whether a given MR image represents a healthy or a diseased brain and in this latter case, is able to locate the tumor area.

Indoor scene recognition and semantic information can be helpful for social robots. Recently, in the field of indoor scene recognition, researchers have incorporated object-level information and shown improved performances. This paper demonstrates that scene recognition can be performed solely using object-level information in line with these advances. A state-of-the-art object detection model was trained to detect objects typically found in indoor environments and then used to detect objects in scene data. These predicted objects were then used as features to predict room categories. This paper successfully combines approaches conventionally used in computer vision (YOLO) and Term Frequency-Inverse Document Frequency (TF-IDF). These approaches could be further helpful in the field of embodied research and dynamic scene classification, which we elaborate on.

Pedestrian multi-target tracking technology plays an important role in artificial intelligence, driverless, virtual reality and other fields. The pedestrian multi-target tracking algorithm DeepSORT based on detection is widely used in industry. It mainly tracks multiple pedestrian targets continuously and keeps their ID unchanged. In order to improve the applicability and tracking accuracy of DeepSORT algorithm, this paper improved the IOU distance measurement in the matching process. At the same time, ResNet50 is used as the feature extraction backbone network, and combined with FPN (Feature Pyramid Network), the appearance features of multi-layer pedestrians are fused to improve the tracking accuracy of DeepSORT algorithm. The proposed algorithm is verified on the public data set MOT-16 and it’s tracking accuracy is enhanced to 4.1%.

Stop words are very important for information retrieval and text analysis investigation. This study aimed to automatically analyze and detect stop words in texts in the Uzbek language. Because of the limited availability of methods for automatic search of stop words of texts in Uzbek we analyzed a newly prepared corpus. The Uzbek language belongs to the family of agglutinative languages. As with all agglutinative languages, we can explain that the detection of stop words in Uzbek texts is a more complex process than in inflected languages: In inflected languages, words such as auxiliary words, articles, prepositions can be included in the stop words group. In agglutinative languages, the meanings of such words are hidden in the text. Therefore, it is not appropriate to apply all known methods of stop words detection in inflected languages directly to agglutinative languages. In this work, the “School corpus” which contains 731156 Uzbek words has been investigated. The bigram method of analysis was applied to the corpus. We proposed the collocation method of detecting stop words of the corpus. We proposed the method of automatically detecting stop words of texts in Uzbek. It is shown that the collocation method is 6 times better than the bigram method.

Recently, the use of drones/unmanned aerial vehicles (UAVs) has notably increased due to their broad commercial spread and low cost. The wide diffusion of drones increases the hazards of their misuse in illegitimate actions such as drug smuggling and terrorism. Thus, the surveillance and automated detection of drones are crucial for safeguarding restricted regions or special zones from illegal drone interventions. One of the most challenging issues in drone detection in surveillance videos is the apparent similarity of drones and birds against complex backgrounds. In this work, an automated image-based drone-detection system utilizing an advanced deep-learning-based object-detection method known as you only look once (YOLOv5) is introduced for protecting restricted regions or special zones from unlawful drone interventions. Due to the lack of sufficient data, transfer learning was utilized to pretrain the object-detection method to increase the performance. The experiments showed outstanding results, and an average precision of 94.7% was accomplished.

Scientists and astronomers have attached Scientists and astronomers have attached great importance to the task of discovering new exoplanets, even more so if they are in the habitable zone. To date, more than 4300 exoplanets have been confirmed by NASA, using various discovery techniques, including planetary transits, in addition to the use of various databases provided by space and ground-based telescopes. This article proposes the development of a deep learning system for detecting planetary transits in Kepler Telescope lightcurves. The approach is based on related work from the literature and enhanced to validation with real lightcurves. A CNN classification model is trained from a mixture of real and synthetic data, and validated only with real data and different from those used in the training stage. The best ratio of synthetic data is determined by the perform of an optimisation technique and a sensitivity analysis. The precision, accuracy and true positive rate of the best model obtained are determined and compared with other similar works. The results demonstrate that the use of synthetic data on the training stage can improve the transit detection performance on real light curves.

Liquid biopsy via isolation of circulating tumour cells (CTCs) represents a promising diagnostic tool capable of supplementing state-of-the-art for prostate cancer (PC) prognosis. Unfortunately, most of CTC technologies, such as AdnaTest or Cellsearch, critically rely on the Epithelial-Cell-Adhesion-Molecule (EpCAM) marker, limiting the possibility of detecting stem-like cells (CSCs) and mesenchymal-like cells (EMT-CTCs) that are present during PC progression. In this tontext, dielectrophoresis (DEP) is an epCAM independent, label-free, enrichment system, separating rare cells simply on the basis of their specific electrical properties. As compared to other technollgies, DEP represents a superior technique in terms of running costs, cells yield and specificity, but due to its higher complexity, requires still further technical as well as clinical development. Interestingly, DEP can be improved by the use of microfluid, nanostructured materials and fluoroimaging in order to increase its potential applications. In the context of PC, the utility of DEP can be translated in its capacity to detect CTC in the bloodstream in their epithelial, mesenchymal, or epithelial-mesenchymal phenotypes, which should be taken into account when choosing CTC enrichment and analysis methods for PC prognosis and early diagnosis.

Recently, spam emails have become a significant problem with the expanding usage of the Internet. It is to some extend obvious to filter emails. A spam filter is a system that detects undesired and malicious emails and blocks them from getting into the users' inboxes. Spam filters check emails for something "suspicious" in terms of text, email address, header, attachments, and language. However, we have used different features such as word2vec, word n-grams, character n-grams, and a combination of variable length n-grams for comparative analysis in our proposed approach. Different machine learning models such as support vector machine (SVM), decision tree (DT), logistic regression (LR), and multinomial naïve bayes (MNB) are applied to train the extracted features. We use different evaluation metrics such as precision, recall, f1-score, and accuracy to evaluate the experimental results. Among them, SVM provides 97.6 \% of accuracy, 98.8\% of precision, and 94.9\% of f1-score using a combination of n-gram features.

Anomaly detection and segmentation aim at distinguishing abnormal images from normal images and further localizing the anomalous regions. Feature reconstruction based method has become one of the mainstream methods for this task. This kind of method has two assumptions: (1) The features extracted by neural network is a good representation of the image. (2) The autoencoder solely trained on the features of normal images cannot reconstruct the features of anomalous regions well. But these two assumptions are hard to meet. In this paper, we propose a new anomaly segmentation method based on feature reconstruction. Our approach mainly consists of two parts: (1) We use a pretrained vision transformer (ViT) to extract the features of the input image. (2) We design a self-attention autoencoder to reconstruct the features. We regard that the self-attention operation which has a global receptive field is beneficial to the methods based on feature reconstruction both in feature extraction and reconstruction. The experiments show that our method outperforms the state-of-the-art approaches for anomaly segmentation on the MVTec dataset. It is both effective and time-efficient.

Identifying cracks in the incipient state is essential to prevent the failure of engineering structures. Detection methods relying on the analysis of the changes in modal parameters are widely used because of the advantages they present. In our previous research, we have found that eigenfrequencies were capable of indicating the position and depth of damage when sufficient vibration modes were considered. The damage indicator we developed was based on the relative frequency shifts (RFS). To calculate the RFSs for various positions and depths of a crack, we established a mathematical relation that involved the squared modal curvatures in the healthy state and the deflection of the healthy and damaged beam under dead mass, respectively. In this study, we propose to calculate the RFS for beams with several cracks by applying the superposition principle. We demonstrate that this is possible if the cracks are far enough from each other. In fact, if the cracks are close to each other, the superposition method does not work and we distinguish two cases: (i) when the cracks affect the same beam face, the frequency drop is less than the sum of the individual frequency drops, and (ii) on the contrary, cracks on opposite sides cause a decrease in frequency, which is greater than the sum of the frequency drop due to individual damage. When the RFS curves are known, crack assessment becomes an optimization problem, the cost function being the distance between the measured RFSs and all possible RFSs for several vibration modes. Thus, the RFS constitutes a benchmark that characterizes damage using only the eigenfrequencies. We can accurately locate multiple cracks and estimate their severity trough experiments and thus prove the reliability of the proposed method.

In microwave imaging it is often of interest to inspect electrically large spatial regions. In these cases, data must be collected over a great deal of measurement points which entails long measurement time and/or costly, and often unfeasible, measurement configurations. In order to counteract such drawbacks, we have recently introduced a microwave imaging algorithm which looks for the scattering targets in terms of equivalent surface currents supported over a given reference plane. While this method is suited to detect shallowly buried targets, it allows to independently process each frequency data, hence the source and the receivers do not need to be synchronized. Moreover, spatial data can be reduced at large extent, without incurring in aliasing artefacts, by properly combining single-frequency reconstructions. In this paper, we validate such an approach by experimental measurements. In particular, the experimental test site consists of a sand box in open air where metallic plate targets are shallowly buried (few cm) under the air/soil interface. The investigated region is illuminated by a fixed transmitting horn antenna whereas the scattered field is collected over a planar measurement aperture at a fixed height from the air-sand interface. The transmitter and the receiver share only the working frequency information. Experimental results confirm the feasibility of the method.

This paper proposes a neural network which fuses the data received from a camera system on a gantry, to detect moving objects and calculate relative position and velocity of the vehicles traveling on a freeway, this information is used to estimate the traffic flow. To estimate the traffic flow at both microscopic and macroscopic view, this paper used YOLO v4 and DeepSORT for vehicle detection and tracking, then counting the number of vehicles pass through the freeway by drawing virtual lines and hot zones, also counting the velocity of each vehicles. The information is then pass to the traffic control center, in order to monitoring and control traffic flow on freeways, and analyzing freeway conditions.

The study aimed to identify different molds that grow on various food surfaces. As a result, we conducted a case study for the detection of mold on food surfaces based on the “you only look once (YOLO) v5” principle. In this context, a dataset of 2050 food images with mold growing on their surfaces was created. The dataset was trained using the pre-trained YOLOv5 algorithm. In comparison to YOLOv3 and YOLOv4, this current YOLOv5 model had better precision, recall, and average precision (AP), which were 98.10%, 100%, and 99.60%, respectively. The YOLOv5 algorithm was used for the first time in this study to detect mold on food surfaces. In conclusion, the proposed model successfully recognizes any kind of mold present on the food surface. Using YOLOv5, we are currently conducting research to identify the specific species of the detected mold.

There is a crucial need for advancement in the online educational system due to the unexpected, forced migration of classroom activities to a fully remote format, due to the coronavirus pandemic. Not only this, but online education is the future, and its infrastructure needs to be improved for an effective teaching-learning process. One of the major concerns with the current video call-based online classroom system is student engagement analysis. Teachers are often concerned about whether the students can perceive the teachings in a novel format. Such analysis was involuntarily done in the offline mode, however, is difficult in an online environment. This research presents an autonomous system for analyzing the students' engagement in the class by detecting the emotions exhibited by the students. This is done by capturing the video feed of the students and passing the detected faces to an emotion detection mode. The emotion detection model in the proposed architecture was designed by finetuning VGG16 pre-trained image classifier model. Lastly, the average student engagement index is calculated. We received considerable performance setting reliability of the use of the proposed system in real-time giving a future scope to this research.

Cancer is one of the health concerns in modern societies. The application of nanotechnology in medical sciences has created new possibilities for the diagnosis, imaging and the treatment of tumors in humans. The present article reviews the application of marine-based gold nanoparticles in diagnosing and treating cancer. The main data were collected from research article on the application of different marine-based gold nanoparticles in detecting and imaging cancer cells as well as in drug delivery system in treatment of cancer. Chitosan is the most used marine natural compound used to fabricate gold nanocomposites and the most reported application of this type of nano-composites is related to drug delivery system. Despite the excellent anticancer potential of different marine natural products, less studies have been conducted on the use of their compositions with gold nanoparticles in cancer therapy than other materials. Moreover, most reports available in this filed are related to their application as a drug delivery system not anticancer drug. In general, there are still challenges and limitations to the use of nanoparticles in medicine, it is hoped that in the near future nanoparticles will create a dramatic revolution not only in oncology but also in medicine.

Hateful and abusive speech presents a major challenge for all online social media platforms. Recent advances in Natural Language Processing and Natural Language Understanding allow more accurate detection of hate speech in textual streams. This study presents a multimodal approach to hate speech detection by combining Computer Vision and Natural Language processing models for abusive context detection. Our study focuses on Twitter messages and, more specifically, on hateful, xenophobic and racist speech in Greek aimed at refugees and migrants. In our approach we combine transfer learning and fine-tuning of Bidirectional Encoder Representations from Transformers (BERT) and Residual Neural Networks (Resnet). Our contribution includes the development of a new dataset for hate speech classification, consisting of tweet ids, along with the code to obtain their visual appearance, as they would have been rendered in a web browser. We have also released a pre-trained Language Model trained on Greek tweets, which has been used in our experiments. We report a consistently high level of accuracy (accuracy score=0.970, f1-score=0.947 in our best model) in racist and xenophobic speech detection.

There are numerous challenges involved in the diagnosis and treatment of lung cancer. Globally, majority of people suffers from cancerous disease involving throat cancer, lung cancer, stomach cancer, cancerous brain tumor. Among these the most common ones is the lung cancer or lung carcinoma. The leading cause of the lung cancer is the smoking. Around 80% to 90% of deaths are caused due to Non-small cell lung cancer (NSCLC). The inadequate diagnostic techniques and low chances for the survival of lung cancer patients results from the lack of an early prognosis and incompetency in traditional therapies. However, such challenges involved in the prognosis and treatment of lung cancer are on decline with the progression in magnetic nanoparticle (MNP) technology. Many break-through discoveries and inventions have been made in the field of cancer therapy by using magnetic nanoparticles. The implication of nanotechnology has led to the recent advancement in nanomedicine field. This has encouraged the improvement in different therapeutic and diagnosis strategies employing nanotechnology. The generation of immense technological benefits for nanoparticles systems has been accredited to its remarkable nanoscale physico-chemical properties. This in turns provides the early detection of lung cancer and active drugs delivery for an improved theranostics strategy. The present review provides a general idea of the current progression in the therapeutic and prognosis purpose of magnetic nanoparticles. Further, we disclose the development in the lung cancer theranostics by functionalization of magnetic nanoparticles. The established importance of magnetic nanoparticles in the theranostics centers for lung cancer has been revealed in this paper. The challenges existing in the theranostics of lung cancer are addressed through the functioning of magnetic nanoparticles in the process.

Sarcasm is a linguistic expression often used to communicate the opposite of what is said, usually something that is very unpleasant with an intention to insult or ridicule. Inherent ambiguity in sarcastic expressions, make sarcasm detection very difficult. In this work, we focus on detecting sarcasm in textual conversations from various social networking platforms and online media. To this end, we develop an interpretable deep learning model using multi-head self-attention and gated recurrent units. Multi-head self-attention module aids in identifying crucial sarcastic cue-words from the input, and the recurrent units learn long-range dependencies between these cue-words to better classify the input text. We show the effectiveness of our approach by achieving state-of-the-art results on multiple datasets from social networking platforms and online media. Models trained using our proposed approach are easily interpretable and enable identifying sarcastic cues in the input text which contribute to the final classification score. We visualize the learned attention weights on few sample input texts to showcase the effectiveness and interpretability of our model.

Identifying dust aerosols from passive satellite images is of great interest for many applications. In this study, we developed 5 different machine-learning (ML) and deep-learning (DL) based algorithms, including Logistic Regression, K Nearest Neighbor, Random Forest (RF), Feed Forward Neural Network (FFNN), and Convolutional Neural Network (CNN), to identify dust aerosols in the daytime satellite images from the Visible Infrared Imaging Radiometer Suite (VIIRS) under cloud-free conditions on a global scale. In order to train the ML and DL algorithms, we collocated the state-of-the-art dust detection product from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) with the VIIRS observations along the CALIOP track. The 16 VIIRS M-band observations with the center wavelength ranging from deep blue to thermal infrared, together with solar-viewing geometries and pixel time and locations, are used as the predictor variables. Four different sets of training input data are constructed based on different combinations of VIIRS pixel and predictor variables. The validation and comparison results based on the collocated CALIOP data indicates that the FFNN method based on all available predictor variables is the best performing one among all methods. It has an averaged dust detection accuracy of about 81 %, 89 % and 85 % over land, ocean and whole globe, respectively, compared with collocated CALIOP. When applied to off-track VIIRS pixels, the FFNN method retrieves geographical distributions of dust that are in good agreement with on-track results as well as CALIOP statistics. For further evaluation, we compared our results based on the ML and DL algorithms to NOAA’s Aerosol Detection Product (ADP) , which is a product that classifies dust, smoke and ash using physical-based methods. The comparison reveals both similarity and differences. Overall, this study demonstrates the great potential of ML and DL methods for dust detection and proves that these methods can be trained on the CALIOP track and then applied to the whole granule of VIIRS granule.

Early detection of stress can prevent us from suffering from a long-term illness such as depression and anxiety. This article presents a scoping review of stress detection based on electrodermal activity (EDA) and machine learning (ML). From an initial set of 395 articles searched in six scientific databases, 58 were finally selected according to various criteria established. The scoping review has made it possible to analyse all the steps to which the EDA signals are subjected: acquisition, preprocessing, processing and feature extraction. Finally, all the ML techniques applied to the features of this signal have been studied for stress detection. It has been found that support vector machines and artificial neural networks stand out within the supervised learning methods given their high performance values. On the contrary, it has been evidenced that unsupervised learning is not very common in the detection of stress through EDA. This scoping review concludes that the use of EDA for the detection of arousal variation (and stress detection) is widely spread, with very good results in its prediction with the ML methods found during this review.

The zero velocity update(ZUPT) algorithm is the core of a foot-mounted pedestrian navigation system. The zero velocity detection method is the premise and guarantee of the effective application of the ZUPT algorithm. To make ZUPT work properly, it is necessary to detect zero velocity intervals correctly. The detection accuracy of the existing zero velocity detection methods is easy to be affected by users and environment. A novel zero velocity detection method based on the plantar pressure is proposed in this paper, which has higher detection accuracy and better environmental adaptability. First, the paper analyzes the motion characteristics of foot during walking. Second, the inherent relationship between the plantar pressure and the gait change during walking is studied based on the pressure sensor. Then, the model of the zero velocity detection method using the plantar pressure is established. Finally, the indoor and outdoor multi-scene experiments show that this method not only has a high detection accuracy, but also has good adaptability to users and walking environment.

The article’s goal is to overview challenges and problems on the way from the state of the art CUDA accelerated neural networks code to multi-GPU code. For this purpose, the authors describe the journey of porting the existing in the GitHub, fully-featured CUDA accelerated Darknet engine to OpenCL. The article presents lessons learned and the techniques that were put in place to make this port happen. There are few other implementations on the GitHub that leverage the OpenCL standard, and a few have tried to port Darknet as well. Darknet is a well known convolutional neural network (CNN) framework. The authors of this article investigated all aspects of the porting and achieved the fully-featured Darknet engine on OpenCL. The effort was focused not only on the classification with the use of YOLO1, YOLO2, and YOLO3 CNN models. They also covered other aspects, such as training neural networks, and benchmarks to look for the weak points in the implementation. The GPU computing code substantially improves Darknet computing time compared to the standard CPU version by using underused hardware in existing systems. If the system is OpenCL-based, then it is practically hardware independent. In this article, the authors report comparisons of the computation and training performance compared to the existing CUDA-based Darknet engine in the various computers, including single board computers, and, different CNN use-cases. The authors found that the OpenCL version could perform as fast as the CUDA version in the compute aspect, but it is slower in memory transfer between RAM (CPU memory) and VRAM (GPU memory). It depends on the quality of OpenCL implementation only. Moreover, loosening hardware requirements by the OpenCL Darknet can boost applications of DNN, especially in the energy-sensitive applications of Artificial Intelligence (AI) and Machine Learning (ML).

In the past years, various intelligent machine learning and deep learning algorithms have been developed and widely applied for gearbox fault detection and diagnosis. However, the real-time application of these intelligent algorithms has been limited, mainly due to the fact that the model developed using data from one machine or one operating condition has serious diagnosis performance degradation when applied to another machine or the same machine with a different operating condition. The reason for poor model generalization is the distribution discrepancy between the training and testing data. This paper proposes to address this issue using a deep learning based cross domain adaptation approach for gearbox fault diagnosis. Labelled data from training dataset and unlabeled data from testing dataset is used to achieve the cross-domain adaptation task. A deep convolutional neural network (CNN) is used as the main architecture. Maximum mean discrepancy is used as a measure to minimize the distribution distance between the labelled training data and unlabeled testing data. The study proposes to reduce the discrepancy between the two domains in multiple layers of the designed CNN to adapt the learned representations from the training data to be applied in the testing data. The proposed approach is evaluated using experimental data from a gearbox under significant speed variation and multiple health conditions. An appropriate benchmarking with both traditional machine learning methods and other domain adaptation methods demonstrates the superiority of the proposed method.

In attempting to predict the further course of the novel coronavirus (COVID-19) pandemic caused by SARS-CoV-2, mathematical models of different types are frequently employed and calibrated to reported case numbers. Among the major challenges in interpreting these data is the uncertainty about the amount of undetected infections, or conversely: the detection ratio. As a result, some models include assumptions about the percentage of detected cases among total infections while others completely neglect undetected cases. Here, we illustrate how model projections about case and fatality numbers vary significantly under varying assumptions on the detection ratio. Uncertainties in model predictions can be significantly reduced by representative testing, both for antibodies and active virus RNA, to uncover past and current infections that have gone undetected thus far.

Many people can take photos with smartphones and easily post photos via SNS (Social Network Services). This has caused a social problem that unintended appearance in photos may threaten the privacy of photographed persons. For this issue, numerous studies have already been introduced to prevent the unintended appearance in photos from the photographer’s side, but only a few methods tackled this from the photographed person's side. Therefore, we considered calling attention to a situation that a photo-taking behavior by a photographer can be automatically detected by using a wearable camera worn by a photographed person. In this paper, we propose an approach to detect photo-taking behaviors in video data taken from the wearable camera, analyzing specific human skeleton information. OpenPose is utilized to obtain the human’s skeleton information and the time-series data are analyzed. In addition, we compare two similar behaviors which are photo-taking behaviors and net-surfing behaviors. These video data are distinguished by DP matching and cross-validation. Finally, it is concluded that the detection accuracy of photo-taking behaviors is about 92.5%, which is satisfactory enough for this research purpose.

An experimental ultra wideband ground penetrating radar based on Golay complementary sequences is proposed to locate underground pipes. Golay complementary sequences with the code length of 1024 and frequency of 1 GHz are used as the probe signals. Two-dimensional image of the buried pipes is achieved by correlation method and back projection algorithm. The experimental results show that both the plastic pipe and metallic pipe can be located with a range resolution of 10 cm. Furthermore, as the Golay complementary sequences are a pair of complementary sequences, the sum of their correlation function yields twice the value of the peak at the target position and zero elsewhere. Thus, compared with the stepped frequency signal radar or chaotic signal radar, the Golay-based radar can significantly improve the signal noise ratio and has capability of deep detection.

Road surface monitoring more specifically crack detection on the surface of the road pavement is a complicated task which is found vital due to critical nature of roads as elements of transportation infrastructure. Cracks on the road pavement is detectable using remotely sensed imagery or car mounted platforms. UAV’s are also considered as useful tools for acquiring reliable information about the pavement of the road. In This paper, an automatic method for crack detection on the road pavement is proposed using acquired videos from UAV platform. Selecting key frames and generating Ortho-image, violating non road regions in the scene are removed. Then through an edge based approach hypothesis crack elements are extracted. Afterwards, through SVM based classification true cracks are detected. Developing the proposed method, the generated results show 75% accuracy in crack detection while less than 10% of cracks are omitted.

Counterfeiting electronic components is a serious problem for the security and reliability of any electronic systems. Unfortunately, the number of counterfeit components has increased considerably after the introduction of horizontal semiconductor supply chain. In this paper, we propose a new method for detecting recycled Flash memory, a major target of the counterfeiters due to its ubiquitous usage. Proposed method is based on measurement of change in Flash array characteristics (such as erase time, program time, fail bit count, etc.) with its usage. We find that erase time is the best metric to distinguish a used Flash chip from a fresh one for the following reasons: (1) erase time shows minimal variation among different fresh memory blocks/chip and (2) erase time increases significantly with usage. We verify our method for a wide range of commercial off the shelf Flash chips from several vendors, technology nodes, storage density and storage type (single-bit per cell and multi-bit per cell). The minimum detectable chip usage varies from 0.05% to 3.0% of its total lifetime depending on the exact details of the chip.

The Operational Remote Sensing (ORS) program leverages Landsat and MODIS data to detect forest disturbances across the conterminous United States (CONUS). The ORS program was initiated in 2014 as a collaboration between the US Department of Agriculture Forest Service Geospatial Technology and Applications Center (GTAC) and the Forest Health Assessment and Applied Sciences Team (FHAAST). The goal of the ORS program is to supplement the Insect and Disease Survey (IDS) and MODIS Real-Time Forest Disturbance (RTFD) programs with imagery-derived forest disturbance data that can be used to augment traditional IDS data. We developed three algorithms and produced ORS forest change products using both Landsat and MODIS data. These were assessed over Southern New England and the Rio Grande National Forest. Reference data were acquired using TimeSync to conduct an independent accuracy assessment of IDS, RTFD, and ORS products. Overall accuracy for all products ranged from 77.64% to 93.51% (kappa 0.09–0.59) in the Southern New England study area and 59.57% to 79.57% (kappa 0.09–0.45) in the Rio Grande National Forest study area. In general, ORS products met or exceeded the overall accuracy and kappa of IDS and RTFD products. This demonstrates the current implementation of ORS is sufficient to provide data to augment IDS data.

Pollution caused by copper is one of the key factors of environment contamination. As one of heavy metals, copper is hard to decompose in nature, the biological enrichment of which may lead to severe damage to health. Cu²⁺ detection, thus, possesses a bright application prospect both in environment protection and in human health. In this paper, a dual-functional fluorescence-magnetic composite nano-platform has been designed to sensitively detect, meanwhile capture and remove Cu²⁺ in the solution of water and ethanol (1:1, v/v). The core-shell structure nanoparticle synthesized by using Fe₃O₄ as core and SiO₂ as shell, is covalently bonded with rhodamine derivatives on the silica layer to construct the nano-platform. The emission is increased upon the addition of Cu²⁺, showing fluorescence turn on effect for the detection, and the limit of detection which was as low as 1.68 nM. Meanwhile, Cu²⁺ ions are captured by the coordination with rhodamine derivatives, and can be removable with the help of magnetic field.

Breast cancer is the most common malignancies in women and the second leading cause of cancer death in women. Triple negative breast cancer (TNBC) subtype is a breast cancer subset without ER, PR and HER2 expression, limiting treatment options and presenting a poorer survival rate. Thus, we investigated whether HDACi would be used as potential anti-cancer therapy on breast cancer cells. In this study, we found TNBC and HER2-enrich breast cancers are extremely sensitive to Panobinostat, Belinostat of HDACi via experiments of cell viability assay, apoptotic marker identification and flow cytometry measurement. On the other hand, we developed a bioluminescence based live cell non-invasive apoptosis detection sensor (IADS) detection system to evaluate the quantitative and kinetic analyses of apoptotic cell death by HDAC treatment on breast cancer cells. In addition, the use of HDACi may also be accompanied with chemotherapeutic agent such as doxorubicin to synergic drug sensitivity on TNBC cell (MDA-MB-231), but not in breast normal epithelia cells (MCF-10A), providing therapeutic benefits against breast tumor in clinic.

Natural events such as floods, fires, tsunamis, earthquakes and others have nowadays caused serious damage to human beings and nature. The precise detection of these natural events and especially the earthquake has nowadays become the focus of many computer and geoscientific researchers. Computer science and machine learning algorithms have revolutionized early detection and prediction of these events. Hence, a fuzzy method has been initially used in this article to enhance the authenticity of data based on application of effective variables and then combination of neural network algorithms of the MLP perceptron and radial network of RBF in form of a collective learning system in order to more accurately identify seismic events on a small scale. It was observed after simulating the proposed method that the proposed method has significantly improved based on actual error and root-mean-square error (RMSE) criteria compared to basic methods.

Smartphones, smartwatches, fitness trackers, and ad-hoc wearable devices are being increasingly used to monitor human activities. Data acquired by the hosted sensors are usually processed by machine-learning-based algorithms to classify human activities. The success of those algorithms mostly depends on the availability of training (labeled) data that, if made publicly available, would allow researchers to make objective comparisons between techniques. Nowadays, publicly available data sets are few, often contain samples from subjects with too similar characteristics, and very often lack of specific information so that is not possible to select subsets of samples according to specific criteria. In this article, we present a new smartphone accelerometer dataset designed for activity recognition. The dataset includes 11,771 activities performed by 30 subjects of ages ranging from 18 to 60 years. Activities are divided in 17 fine grained classes grouped in two coarse grained classes: 9 types of activities of daily living (ADL) and 8 types of falls. The dataset has been stored to include all the information useful to select samples according to different criteria, such as the type of ADL performed, the age, the gender, and so on. Finally, the dataset has been benchmarked with two different classifiers and with different configurations. The best results are achieved with k-NN classifying ADLs only, considering personalization, and with both windows of 51 and 151 samples.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

Cyber security has recently received enormous attention in today’s security concerns, due to the popularity of the Internet-of-Things (IoT), the tremendous growth of computer networks, and the huge number of relevant applications. Thus, detecting various cyber-attacks or anomalies in a network and building an effective intrusion detection system that performs an essential role in today’s security is becoming more important. Artificial intelligence, particularly machine learning techniques, can be used for building such a data-driven intelligent intrusion detection system. In order to achieve this goal, in this paper, we present an Intrusion Detection Tree (“IntruDTree”) machine-learning-based security model that first takes into account the ranking of security features according to their importance and then build a tree-based generalized intrusion detection model based on the selected important features. This model is not only effective in terms of prediction accuracy for unseen test cases but also minimizes the computational complexity of the model by reducing the feature dimensions. Finally, the effectiveness of our IntruDTree model was examined by conducting experiments on cybersecurity datasets and computing the precision, recall, fscore, accuracy, and ROC values to evaluate. We also compare the outcome results of IntruDTree model with several traditional popular machine learning methods such as the naive Bayes classifier, logistic regression, support vector machines, and k-nearest neighbor, to analyze the effectiveness of the resulting security model.

In emergency situations, ensuring standardized Cardiopulmonary Resuscitation (CPR) actions is crucial. However, current Automated External Defibrillators (AEDs) lack methods to determine whether CPR actions are performed correctly, leading to inconsistent CPR quality. To address this issue, we introduce a novel method called Deep Learning-based CPR Action Standardization (DLCAS). This method involves three parts. First, it detects correct posture using OpenPose to recognize skeletal points. Second, it identifies a marker wristband with our CPR-Detection algorithm and measures compression depth, count and frequency using a depth algorithm. Finally, we optimize the algorithm for edge devices to enhance real-time processing speed. Extensive experiments on our custom dataset have shown that the CPR-Detection algorithm achieves a mAP0.5 of 97.04%, while reducing parameters to 0.20M and FLOPs to 132.15K. In a complete CPR operation procedure, the depth measurement solution achieves an accuracy of 90% with a margin of error less than 1 cm, while the count and frequency measurements achieve 98% accuracy with a margin of error less than 2 counts. Our method meets the real-time requirements in medical scenarios, and the processing speed on edge devices have increased from 8fps to 25fps.

Railway transportation is one of the main modes of long-distance coal transportation, and it is inevitable to cause environmental pollution during the transportation process. In order to improve the environment along the railway and increase the utilization rate of coal resources, this paper proposes a detection algorithm for scattered coal solidification layer during transportation based on the YOLO v8 model, and designs an intelligent recognition model suitable for coal solidification layer detection devices by combining fluorescence detection methods. Through experimental analysis, the model meets the requirements of practical detection and plays a crucial role in environmental protection, with strong practical application value.

This study introduces a novel algorithm tailored for the precise detection of lower outliers in univariate datasets, particularly suited for scenarios with a single cluster. The approach leverages a combination of transformative techniques and advanced filtration methods to efficiently segregate anomalies from normal values. Notably, the algorithm emphasizes high precision, ensuring minimal false positives, and requires only a few parameters for configuration. Its unsupervised nature enables robust anomaly filtering without the need for extensive manual intervention. To validate its efficacy, the algorithm is rigorously tested using real-world data obtained from photovoltaic (PV) module strings with similar DC capacities, containing various anomalies. Results demonstrate the algorithm's capability to accurately identify lower outliers while maintaining computational efficiency and reliability in practical applications.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

Camouflage evaluation typically involves human visual search and detection experiments that are time-consuming and expensive. Hence, there is a need for models that compute camouflage effectiveness from digital imagery. Convolutional neural networks are a powerful tool for automatic object detection and recognition. We investigated whether such a network (YOLO) can also provide a measure of camouflage effectiveness that is related to human perception. To this end, human performance measures of camouflage effectiveness such as detection time and target conspicuity were obtained in observer experiments and compared with the performance of the (standard, i.e. pre-trained) YOLO-V4-tiny algorithm. YOLO provides the probability that a detected object is correctly classified, and this is adopted as our measure of camouflage effectiveness. We compared the YOLO-predicted classification probability for a person in camouflage clothing moving through rural and urban scenes to human detection performance. Overall, camouflage effectiveness predicted by YOLO correlates with human observer performance. At close distances, YOLO’s classification performance appears sensitive to high-contrast shape-breaking elements of a camouflage pattern. This suggests that YOLO may be adapted to assess camouflage effectiveness for a wide range of applications, such as evaluating or optimizing one’s signature and predicting optimal hiding locations in a given environment. Further research is required to fully establish YOLO’s limitations and applicability for this purpose.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

The growing shift toward Internet of Things (IoT)-based solutions expands the attack surface of systems by connecting an extensive network of heterogeneous devices and technologies. The heterogeneity of IoT devices and the scale of the network often make conventional security measures impractical. Therefore, recent research efforts have focused on machine learning (ML)-based device-agnostic IoT security solutions. However, most proposed solutions have focused solely on detecting malicious traffic in IoT networks. While this is important, further information about the attack is needed to provide a comprehensive defense before, during, and after the incident. To address this gap, we proposed an anomaly-based intrusion detection model that detects malicious traffic and identifies the attack category and subcategory with high accuracy, recall, precision, and F1-score. The proposed intrusion detection model is an ensemble model that integrates multiple ML models to produce more robust and reliable detections. For evaluation, we performed three sets of experiments: (1) a binary classification to detect malicious traffic; (2) a multi-class classification to detect the attack category; and (3) a multi-class classification to detect the attack subcategory. In the experiments, our model achieved an accuracy, recall, precision, and F1-score of 100% for the binary detection; a precision, recall, and F1-score of 99% and an accuracy of 100% for the multi-class category classification; and an accuracy, recall, precision, and F1-score of 88% for the multi-class subcategory classification. These results suggest that the proposed model can reliably detect anomalies in IoT devices.

Achieving effective control over microbial contamination necessitates the precise and concurrent identification of numerous pathogens. In this research, we have devised a remarkably sensitive duplex droplet digital PCR (dddPCR) reaction system to simultaneously detect Pseudomonas aeruginosa (P. aeruginosa) and Pseudomonas fragi (P. fragi). Employing comparative genomics, we identified four genes of P. fragi. By specific analysis, RS22680 gene was selected as the detection target of P. fragi and LasR gene was chosed as P. aeruginosa, which were applied to construct a dddPCR reaction. In terms of specificity, sensitivity and anti-interference ability, the constructed dddPCR detection system was verified and analyzed. The assay showed excellent sensitivity and applicability, as evidenced by a limit of detection of 100 CFU/mL. When the concentration of natural background bacteria in milk or fresh meat was 100 times that of the target detection bacteria, the method was still capable of completing the absolute quantification. In the simulation of actual sample contamination, P. aeruginosa could be detected after 3 h of enrichment culture, and P. fragi could be detected after 6 h. The established ddPCR detection system exhibits exceptional performance, serving as a foundation for the simultaneous detection of various pathogenic bacteria in food products.

The Distributed eLearning Center (DeLC) is a portal, providing extensive support in the day-to-day work when it comes to e-learning content – it helps students and teachers organize their learning materials, fill the gaps in knowledge (for students) and educational approaches (for teachers), organize and conduct exams, and overall, with providing proactive and personalized e-learning environment. The scope of DeLC as a project involves many extensions, covering the aspects of learning, teaching, exams, and collecting statistical information. Such extension is an agent-oriented environment, which enriches the functionalities with intelligent components, that are reactive and proactive, referred to as agents or assistants. This paper is focused on presenting the latest step in the evolution of FraudDetector software agent, which started with base functionality for fraud detection, and now it aims at usage of AI to accomplish its tasks, taking advantage not only from its knowledgebase, but from a much larger one, used by ChatGPT – through integration with it, which is the main contribution of this research, although the real results from production environment are still pending. In this process, agent’s architecture should stay open for collaboration with another external AI provider if necessary, trying to decouple the components, responsible for integration. As of now, the experiments show that involving ChatGPT in FraudDetector’s functionality enriches it and the agent’s precision could be improved this way.

Detecting the presence of explosives is important to protect human lives in military conflicts and peacetime. Gas-phase detection of explosives can make use of the change of material properties, which can be sensitive to environmental conditions such as temperature and humidity. This paper describes a remote-controlled automatic shutter method for environmental impact assessment of photoluminescence (PL) sensors under near-open conditions. Utilizing the remote-sensing method, we obtained environmental effects without being exposed to sensing vapor molecules, and explained how PL intensity was influenced by the temperature, humidity, and exposure time. We also developed a theoretical model including the effect of exciton diffusion for PL quenching, which worked well under limited molecular diffusions. Incomplete recovery of PL intensity, or degradation effect, was considered as an additional factor in the model.

In response to the growing challenges in drone security and airspace management, this study introduces an advanced drone classifier, capable of detecting and categorizing Unmanned Aerial Vehicles (UAVs) based on acoustic signatures. Utilizing a comprehensive database of drone sounds across EU-defined classes (C0 to C3), this research leverages machine learning (ML) techniques for effective UAV identification. The study primarily focuses on the impact of data augmentation methods—pitch shifting, time delays, harmonic distortion, and ambient noise integration—on classifier performance. These techniques aim to mimic real-world acoustic variations, thus enhancing the classifier's robustness and practical applicability. Results indicate that moderate levels of augmentation significantly improve classification accuracy. However, excessive application of these methods can negatively affect performance. The study concludes that sophisticated acoustic data augmentation can substantially enhance ML-driven drone detection, providing a versatile and efficient tool for managing drone-related security risks. This research contributes to UAV detection technology, presenting a model that not only identifies but also categorizes drones, underscoring its potential for diverse operational environments.

In mobile robotics, laser scanners have a wide spectrum of indoor and outdoor applications, both in structured and unstructured environments, due its accuracy and precision. Most works that use this sensor have their own data representation and their own case-specific modeling strategies, and no common formalism is adopted. To address this issue, this manuscript presents an analytical approach for identification and localization of objects using a 2D LiDARs Our main contribution lies in formally defining laser sensor measurements and their representation, the identification of objects, their main properties and their location in a scene. We validate our proposal with experiments in generic semi-structured environments common in autonomous navigation, and we demonstrate its feasibility on multiple object detection and identification, following strictly its analytical representation. Finally, our proposal further encourages and facilitates the design, modeling and implementation of other applications that use laser scanners as a distance sensor.

Background: Human papillomavirus (HPV) is diagnosed in most cervical cancers and is the fourth cause of cancer worldwide. Currently, fourteen HPV types are considered carcinogenic (HPV 16/18/31/33/35/39/45/51/52/56/58/59/66/68) with different oncogenicity. Cervical lesions might be due to HR (high risk)-HPV for what is important to identify new methods to genotype cervical lesions. The main goal was to identify, for the first time, HPV-HR in cervical lesions using Anyplex™ Detection kit in paraffin-embedded tissue. (2) Methods: It was performed a retrospective study in 45 women from Academic Hospital of Cova da Beira (CHUCB). DNA extraction was performed and through Anyplex™ II HPV-HR Detection kit HPV-HR were genotyped. (3) Results: HPV-HR were identified in 38 women; HPV-16 (55,26%), HPV-18/39/56/58/59 (5,26%), HPV-31 (21,05%), HPV-35 (7,89%), HPV-51/6 (2,63%) and HPV-52 (10,53%). (4) Conclusions: Our results reflect that Anyplex™ II HPV-HR Detection kit, designed for HR-HPV genotyping of cervical cancer screening, might be properly used to HR-HPV genotyping in histology. The proposed methodology allows an easy and cheaper technique that should be used as a future cervical risk stratification. It is a strong tool to be implemented in clinical practice in order to detect HR-HPV detection in cervical lesions, contributing to a more accurate diagnosis.

Despite UAV multi-target detection exhibits considerable developmental potential worldwide, it suffers distinct challenges compared with traditional tasks in this field. These challenges include insufficient feature extraction capabilities for small targets, limited capabilities for multi-dimensional feature fusion, as well as constraints on hardware computation parameters. Especially in mission scenarios such as disaster detection, these challenges will be further amplified. Consequently, this paper introduces SSE-YOLO, an innovative YOLO framework algorithm specially designed to address these challenges. To enhance the model's feature extraction capability, we employ the SPDConv module to replace the original Conv in the backbone section, utilizing depth-separable convolution instead of traditional convolution pooling. Concurrently, we eliminate the SPPF module at the bottom and address a new Separate Kernel Attention Pyramid Pooling (SKAPP) module, substantially enhancing the feature fusion capability at the model's core. Moreover, to address the challenge of multi-dimensional feature fusion, we replace the Concat module of the neck and head with E-BiFPN, transmitting feature information from the backbone to the lower network through four CBS blocks, which effectively resolves the issue of lost contextual information in the model. Meanwhile, SSE-YOLO undergoes ablation experiments on the VisDrone2019 dataset to evaluate its effectiveness against alternative methods, and experimental results illustrate the model's exceptional precision in detecting UAV targets. In comparison to models with comparable experimental accuracy, SSE-YOLO requires remarkably fewer parameters. On the VisDrone2019-DET-test-dev dataset, SSE-YOLO enhances mAP by 17.3%, with a 42.5% reduction in the parameter amounts. Therefore, the proposed method effectively tackles the challenge of reconciling low parameters and high accuracy, presenting a novel pathway for deep learning-based UAV multi-target detection.

This study explores the dependence of drone acoustic detection systems performance on distance, using learning machines with different complexities, from simple linear discriminants, to deep neural networks, such as YAMNet, which exploits transfer learning. Other machine learning systems studied are the multilayer perceptron, support vector machines and random forest. These methods have been evaluated with a meticulously selected database that includes a wide variety of drone and interference sounds, previously processed by array signal processing and affected by ambient noise. Two strategies for training learning machines are considered. In the first one, they are trained with unattenuated signals, trying to preserve the information generated by the sound sources, but they are tested considering the attenuation with distance, achieving effective detection at distances up to 200 metres with some methods, especially linear discriminant. In all cases, the existence of interferences that hinder detection is considered. In the second strategy, the systems are trained and tested with attenuated signals as a function of distance. The effective detection range increases up to 300 metres for most methods and up to 500 metres for the YAMNet based detector. In addition, this second approach raises the possibility of developing specialised detectors for each distance range, thus significantly extending the effective detection range. These results underline the promising potential of acoustic detection of drones at various distances, encouraging further exploration in this research area.

Recent theory of tachyon neutrinos, providing an explanation for Dark Matter, leads to two sets of experiments for testing that theory. One predicts an enhanced signal in detection of the Cosmic Neutrino Background. The other compares models of Dark Matter used to fit data on galaxy rotation curves and also gravitational lensing. In addition, an apparent contradiction within the new theory, related to Dark Energy, is identified and addressed.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

With the deterioration of the bridge performance and ever-increasing amount of traffic, the bridge safety is becoming a concern for engineering community. A method that can assess the bridge's condition in real-time is urgently needed. The main factors that hinder the bridge condition assessment are the uncertain operational environments. A new moving principal component analysis (MPCA) based method is developed for structural damage detection of bridges in operational environments in this paper. Two main operational environmental factors: the environmental temperature and traffic loads, are studied in the assessment process to verify the robustness and practicality of the proposed method. The numerical and experimental results show that the proposed method is effective and accurate to assess the bridge condition in operational environments.

The proliferation of ransomware poses a significant threat to global cybersecurity. This study presents a comprehensive review of the methodologies employed in the detection and analysis of ransomware, emphasizing the dichotomy between static and dynamic analysis approaches. It introduces the historical context and the necessity for robust cybersecurity measures, followed by an outline of the methodological framework used to evaluate existing ransomware analysis techniques. The results detail the effectiveness and limitations of various analysis strategies, identifying key features and patterns that aid in the detection and classification of ransomware threats. The study concludes by summarizing the primary achievements, including the identification of gaps in current research and proposing future research directions aimed at enhancing ransomware detection and mitigation strategies. The synthesis provided in this survey offers a consolidated view of the state-of-the-art in ransomware threat analysis and serves as a resource for cybersecurity professionals and researchers.

Wearing gloves while operating machinery in workshops is an essential precaution to prevent mechanical injuries and burns from high temperatures, among other potential hazards. Ensuring workers are properly equipped with gloves, which is a crucial measure in accident prevention. Glove images often occupy a minimal proportion of the frame and are easily obscured by cluttered backgrounds, especially with limited edge computing resources. Consequently, this study proposes a glove detection algorithm called YOLOv8-AFPN-M-C2f based on YOLOv8, offering swifter detection speeds, lower computational demands, and enhanced accuracy for workshop scenarios. This research innovates by substituting the head of YOLOv8 with the AFPN-M-C2f network, amplifying the pathways for feature vector propagation, and mitigating semantic discrepancies between non-adjacent feature layers. Additionally, the introduction of a superficial feature layer enriches surface feature information, augmenting the model's sensitivity to smaller objects. To assess the performance of the YOLOv8-AFPN-M-C2f model, we conducted multiple experiments using a factory glove detection dataset compiled for this study. The results indicate that the enhanced YOLOv8 model surpasses other network models. Compared to the baseline YOLOv8 model, the refined version shows a 2.6% increase in mAP@50%, a 90.1% rise in FPS, and a 13% reduction in the number of parameters. This research contributes an effective solution for the detection of glove adherence.

The airborne and satellite-based synthetic aperture radar enables the acquisition of high-resolution SAR oceanographic images in which even the outlines of ships can be identified. The detection of ship targets from SAR images has a wide range of applications, such as the military, where the dynamic grasp of enemy targets can help improve the early warning capability of naval defence, and the civilian detection of illegal fishing vessels can help improve the level of maritime management. Due to the density of ships in SAR images, the extreme imbalance between foreground and background clutter, and the diversity of target sizes, achieving lightweight and highly accurate multi-scale ship target detection remains a great challenge. To this end, this paper proposes an attention mechanism for multiscale receptive fields convolution block (AMMRF). AMMRF not only makes full use of the location information of the feature map to accurately capture the regions in the feature map that are useful for detection results, but also effectively captures the relationship between the feature map channels, so as to better learn the relationship between the ship and the background. Based on this, a new YOLOv7-based ship target detection method, You Only Look Once SAR Ship Identification (YOLO-SARSI), is proposed, which acquires the abstract semantic information extracted from the high-level convolution while retaining the detailed semantic information extracted from the low-level convolution. Compared to the deep learning detection methods proposed by previous authors, our model is more lightweight, only 18.43M. We examined the effectiveness of our method on two SAR image public datasets: the High-Resolution SAR Images Dataset (HRSID) and the Large-Scale SAR Ship Detection Dataset-v1.0 (LS-SSDD-V1.0). The results show that the average accuracy AP50 of the detection method YOLO-SARSI proposed in this paper on the HRSID and LS-SSDD-V1.0 datasets is 4.9% and 5% higher than that of YOLOv7, respectively.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Multi-cancer early detection (MCED) tests are being developed, but little is known about patient receptivity to their use for cancer screening. The current study assessed patient interest in such testing. Our team conducted a prospective, observational study among primary care patients in a large, urban health system. They were asked to complete a telephone survey that briefly described a new blood test in development to identify multiple types of cancer, but was not currently recommended or covered by insurance. The survey included items to assess respondent background characteristics, perceptions about MCED testing, and interest in having such an MCED test. We also used multivariable analyses to identify factors associated with patient interest in test use. In 2023, we surveyed 159 (32%) of 500 identified patients. Among respondents, 125 (79%) reported a high level of interest in having an MCED test. Interest was not associated with personal background characteristics, but was positively associated with the following expectations: testing would be recommended for cancer screening, be convenient, and be effective in finding early-stage disease (OR=11.70, 95% CI: 4.02, 34.04, p < 0.001). Research is needed to assess patient interest and actual uptake when detailed information on testing is presented in routine care.

An advanced, cost-effective and portable DNA biosensor capable of detecting multiple bacteria simultaneously have been developed. The biosensor consists of a fast and inexpensive potentiostat that controls the applied potential to a screen-printed electrochemical array platform functionalized with MoS2 flakes and bacteria DNA probes, and monitors the current response obtained by the use of à la carte thionine functionalized carbon nanodots (Ty-CDs) as electrochemical indicator of the hybridization event. The design of the potentiostat prioritizes achieving an optimal signal-to-noise ratio and incorporates a user-friendly interface compatible with various devices such as computers, mobile phones and tablets. The device is compact, lightweight, and manufactured at a low cost. The key components of the potentiostat include a data acquisition board capable of analyzing multiple samples simultaneously and a controller board. The results obtained confirm the ability of the developed device to successfully detect specific bacteria DNA sequences, demonstrating the reliability and performance of the developed multiplexing portable biosensor with better sensibility than using a traditional, more complex and laboratory oriented potentiostat.

In forensic acoustics, a possible area of analysis is represented by unwanted sound that 1 is perceived as a source of intrusion or disturbance within a certain auditory context. This context 2 is defined as the "auditory scene" and refers to the set of sounds present in a specific environment. 3 The presence of unwanted sounds in the auditory scene can cause a wide range of negative effects, 4 including disturbance, discomfort, moral or immoral harm, and other types of negative impact on the 5 health and well-being of individuals exposed to noise. In 2022, the technical specification UNI/TS 6 11844:2022 dedicated to the measurement and analysis of intrusive noise was published. The standard 7 introduces the concept of intrusive noise and defines its calculation methods based on environmental 8 measurements. The purposes of this technical specification is to provide an objective support to 9 methods already in used in acoustic disputes, where the assessment of the annoyance of a noise is 10 often a subjective evaluation of the technician. This work delves into the application to some real 11 cases, identifying the potentiality and the limits of the standardized method.

Underwater target detection is widely used in various applications such as underwater search and rescue, underwater environment monitoring, and Marine resources survey. However, the visibility of the underwater environment and the accuracy of target detection can be affected by complex underwater light changes and unpredictable background noise. To address these issues, we propose an improved underwater target detection algorithm based on YOLOv8n. Our algorithm focuses on three aspects. Firstly, we replace the original C2f module with Deformable Convnets v2 to enhance the adaptive ability of the target region in the convolution check feature map and extract the target region's features more accurately. Secondly, we introduce SimAm, a non-parametric attention mechanism, which can deduce and assign three-dimensional attention weights without adding network parameters. Lastly, we optimize the loss function by replacing the CIOU loss function with the Wise-IOU loss function. To conduct our experiments, we create our own dataset of underwater target detection for experimentation. Meanwhile, we also utilized the Pascal VOC dataset to evaluate our approach. The [email protected] and [email protected]:0.95 of the original YOLOv8n algorithm on the underwater target detection were 88.6% and 51.8%, respectively, and the improved algorithm [email protected] and [email protected]:0.95 can reach 91.8% and 55.9%. The original YOLOV8n algorithm was 62.2% and 45.9% [email protected] and [email protected]:0.95 on the Pascal VOC dataset, respectively. The improved YOLOV8n algorithm [email protected] and [email protected]:0.95 were 65.7% and 48.3%, respectively. The floating-point computation volume of the model is reduced by about 6%. The above experimental results prove the effectiveness of our method.

Stemming from the object overlap and undertraining from the few samples, the road dense object detection is confronted with the poor object identification performance and the inability to recognize edge objects. Based on this, one transfer learning-based YOLOv3 approach for identifying dense objects in the road has been proposed. Firstly, Darknet-53 network structure is adopted to obtain pre-trained YOLOv3 model, then the transfer training is introduced as the output layer for the special dataset of 2000 images containing vehicles; in the proposed model, one random function is adapted to intialize and optimize the weights of the transfer training model, which is seperately designed from the pre-trained YOLOv3; and the object detection classifier replaces the fully connected layer, which further improves the detection effect, the reduced size of the network model can further reduce the training and detection time, and can be better applied to actual scenarios. The experimental results demonstrate that the object detection accuracy of the presented approach is 87.75% for the Pascal VOC 2007 dataset, which is superior to the traditional YOLOv3 and the traditional YOLOv2 by 3.05% and 11.15%, respectively. Besides, the test was carried out using UA-DETRAC, a public road vehicle detection dataset, the object detection accuracy of the presented approach reaches 79.23% in detecting images, which is 4.13% better than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the detection accuracy is 1.36% better. Moreover, the detection speed of the proposed YOLOv3 method reaches 31.2 Fps/s in detecting images, which is 7.6 Fps/s faster than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the speed is 4.3 Fps/s faster; the proposed YOLOv3 performs 79.38Bn of floating point operations per second in detecting video, which obviously surpasses the traditional YOLOv3 and the newer object detection algorithm YOLOv5.

This paper proposes a multimodal fusion 3D target detection algorithm based on the attention mechanism to improve the performance of 3D target detection. The algorithm utilizes point cloud data and information from camera. For image feature extraction, the ResNet50+FPN architecture extracts features at four levels. Point cloud feature extraction employs the voxel method and FCN to extract point and voxel features. The fusion of image and point cloud features is achieved through regional point fusion and regional voxel fusion methods. After information fusion, the Coordinate attention mechanism and SimAM attention mechanism extract fusion features at a deep level. The algorithm's performance is evaluated using the DAIR-V2X dataset. The results show that compared to the Part-A2 algorithm, the proposed algorithm improves the mAP value by 7.9% in BEV view and 7.8% in 3D view at IOU=0.5 (cars) and IOU=0.25 (pedestrians and cyclist). At IOU=0.7 (cars) and IOU=0.5 (pedestrians and cyclist), the mAP value of the SECOND algorithm is improved by 5.4% in the BEV view and 4.3% in the 3D view, compared to other comparison algorithms.

Cancer is a common illness with a high mortality. Compared to traditional technologies, biomarkers detection, with low cost and simple operation, has higher sensitivity and faster speed in early screening and prognosis of cancer. Therefore, extensive research has been focused on the development of biosensors and the construction of sensing interfaces. Molybdenum disulfide (MoS2) is a promising two-dimensional (2D) nanomaterial, whose unique adjustable bandgap shows excellent electronic and optical properties in the construction of biosensor interfaces. It not only has the advantages of high catalytic activity and low manufacturing costs, but also can further expand the application of hybrid structures by different functionalization, and is widely used in various biosensors fields. Herein, the application of electrochemical and optical sensing platforms based on MoS2 in the detection of cancer biomarkers was comprehensively reviewed. Firstly, the structure and preparation method of MoS2 were introduced, and its applicable characteristics in the field of biosensors were explored. Secondly, we comprehensively reviewed the recent construction and application of sensing platform based on MoS2 in the field of cancer biomarkers detection in both electrochemical and optical aspects. The prime characteristics and application performances of MoS2 and its composites were emphasized. Additionally, we also involved some other types of biosensors based on MoS2. Finally, we summarized the challenges and development prospects of MoS2 in the application of cancer biomarkers detection, and provided some insights for the application potential of this kind of emerging nano-materials in a broader field.

High-precision inertial sensors or accelerometers can provide us references of free-falling motions in gravitational field in space, and serve as the key payloads for gravity recovery missions. In this work, a systematic method of electrostatic inertial sensor calibrations for gravity recovery satellites is introduced, which is applied to and verified with the Taiji-1 mission. Taiji-1 is the first technology demonstration satellite of the ``Taiji Program in Space'', which, in its final extended phase in 2022, could be viewed as a gravity recovery satellite operating in the high-low satellite-to-satellite tracking mode. Based on the calibration principles, swing maneuvers with time span about 200 s and rolling maneuvers for 19 days were conducted by Taiji-1 in 2022. The inertial sensor's operating parameters including the scale factors, the center of mass offset vector and the intrinsic biased acceleration are precisely re-calibrated and are updated to the Taiji-1 science team. Data from one of the sensitive axis is re-processed with the updated operating parameters, and the performance is found to be slightly improved compared with former results. This approach could be of high reference value for the accelerometer or inertial sensor calibrations of the GFO, the Chinese GRACE-type mission, and the planned Next Generation Gravity Missions. This could also shed some light on the in-orbit calibrations of the ultra-precision inertial sensors for future GW space antennas because of the technological inheritance between these two generations of inertial sensors.

By shifting the focus from aggregate-level analysis to individual-level analysis, we believe that the DAD model can contribute to a more comprehensive understanding of driving behavior. Combing DAD with a conflict identification (CIM) model can potentially enhance the effectiveness of Advanced Driver Assistance Systems (ADAS) in terms of crash evasion capabilities. This paper is part of our research titled Automatic Safety Diagnosis in Connected Vehicle Environment, which received funding from the Southeastern Transportation Research, Innovation, Development, and Education Center.

MicroRNAs (miRNAs) within the exosomes are short non-coding RNAs that are associated with many diseases including cancers and are crucial players in regulating gene expression and regula-tion. Owing to their potential role as emerging biomarkers, efficient isolation, and quantification methods of miRNA from the exosomes in the cell’s supernatant are complicated and challenging. The quantitative PCR method is the gold standard for miRNA identification and estimation. Nucleic acid-based assays are expensive, labour-intensive, and require expertise. In this work, we demon-strated an aptamer-based magnetic separation of the exosomes, and quantification of the miRNA using a fluorescence switching assay. The fluorescence assay relies on the fluorescence of the fluorophore labelled cDNA quenched by carbon nanomaterials coated on magnetic beads (OFF state). When the target miRNA210 is introduced to the system, the cDNA detaches from the quenching surface. As a result, the fluorescence intensity increases (ON state) with increasing miRNA concentration within the dynamic range of 0-100 nM. This method can detect miR210 as low as 5 pM. This method does not exhibit any cross-reactivity with other closely related miRNAs. The method was validated by spiking miRNA with the standard RT-PCR method using SYBR green as a fluorescent probe. This method can be used for the minimally invasive detection of cancer biomarkers in breast cancer patients.

Detection of virus in sample is an actual problem in biotechnology, virology, medicine using biosensor. History of problem dates back to middle of last century and is associated with development of an ion-sensitive solid-state device for neurophysiological measurements. Aim of work is theoretical investigation process of detection antibody+antigen (AB+AG) complexes using SOI-FET biosensor. On example of crystal with ten biosensors, estimates of probability detection AB+AG complexes influenza virus are made. In detection process, following four results are possible: – target complex is present in test sample, and it was correctly detected; – target complex is present in sample, but it was not detected; – target complex is absent in sample, but background particles are mistakenly detected as target complex; – target complex is absent in sample, background particles present in sample and are correctly detected as noise.

Epigenetic alterations are heritable and enduring modifications in gene expression that play a pivotal role in immune evasion. These include alterations to noncoding RNA, DNA methylation, and histone modifications. DNA methylation plays a crucial role in normal cell growth and development but alterations in methylation patterns such as hypermethylation or hypomethylation can enable tumor and viral cells to evade host immune responses. Histone modifications can also inhibit immune responses by promoting the expression of genes involved in suppressing normal immune function. In the case of T-cell lymphoma, adult T-cell Lymphomas (ALT) also undergo immune evasion through the exceptional function of its accessory and regulatory genes. Epigenetic therapies are emerging as a promising adjunct to traditional immunotherapy and chemotherapy regimens. Clinical trials are currently investigating the use of epigenetic therapies in combination with immunotherapies and chemotherapies for more effective treatment of ATL and other cancers. This review highlights epigenetic alterations that are widely found in T cell malignancies.

As we all know, many more dynamic objects appear almost continuously in real world, which are immensely able to impair the performance of the majority of vision-based SLAM systems that are based on the static-world assumption. In order to improve the robustness and accuracy of visual SLAM in the high dynamic environment, a real-time and robust stereo SLAM system for dynamic scenes was proposed. To weaken influences of dynamic content, the moving object detection method was put forward in our visual odometry, then the semantic segmentation network was combined into our stereo SLAM to extract pixel-level contours of dynamic objects. Then influences of dynamic objects were extremely weaken and the performance of our system was increased markedly in dynamic, complex and crowed city spaces. Experiment with both on KITTI Odometry dataset and in a real-life scene, the results show that our method can dramatically decrease the tracking error or drift, improve the robustness and stability of our stereo SLAM in high dynamic outdoor scenarios.

Antibiotic therapy is a cornerstone of modern medicine, yet the development of antibiotic re-sistance threatens to render these therapies ineffective. The gut microbiota, a complex ecosystem of microorganisms residing in the gastrointestinal tract, plays a critical role in modulating anti-biotic efficacy and resistance. This review delves into the intricate relationship between gut mi-crobiota, antibiotic therapy, and resistance, and discusses the potential applications of gut mi-crobiota research in guiding personalized antibiotic therapy and resistance mitigation strategies. Recent advancements in metagenomics, metatranscriptomics, and metabolomics have demon-strated the potential for tailored antibiotic regimens that minimize collateral damage to com-mensal bacteria and reduce the risk of resistance. Adjuvant therapies such as probiotics, prebi-otics, and synbiotics have shown promise in restoring gut microbial balance and mitigating the adverse effects of antibiotic therapy. We address the challenges associated with this emerging field including the need for standardized methodologies, ethical considerations, and interdisci-plinary collaboration. With continued interdisciplinary collaboration and the implementation of standardized methodologies, gut microbiota research can contribute to the global fight against antibiotic resistance and improve patient outcomes.

significant security threats to Ransomware attacks provide serious security hazards to personal and corporate data and information. The owners of computer-based resources suffer serious verification and privacy violations, monetary losses, and reputational damage due to a successful ransomware assault. As a result, it is reported critically, accurately, and swiftly identifying ransomware. Numerous methods have been proposed for ransomware, each with pros and cons. The main objective of this study is to discuss current trends and potential future debates on automated ransomware detection. The document includes an overview of ransomware, a timeline of assaults, and details on their background. It also provides a comprehensive study of existing methods for identifying, avoiding, minimizing, and recovering from ransomware. An analysis of studies between 2017 and 2022 is another advantage of the study. This provides readers with up-to-date knowledge of the most recent developments in ransomware detection. It also highlights advancements in methods for combating ransomware attacks. In conclusion, this study highlights unanswered concerns and potential research challenges in ransomware detection.

Disease surveillance is critical to monitor ongoing control activities, detect early outbreaks and to inform intervention priorities and policies. Unfortunately, most data from disease surveillance remain under-utilised to support decision-making in real-time. Using the Brazilian Amazon malaria surveillance data as a case study, we explore unsupervised anomaly detection machine learning techniques to analyse and discover potential anomalies. We found that our models are able to detect early outbreaks, peak of outbreaks as well as change points in the proportion of positive malaria cases. Specifically, the sustained rise in malaria in the Brazilian Amazon in 2016 was flagged by several models. We also found that no single model detects all the anomalies across all health regions. The approaches using Clustering-based local outlier algorithm ranked first before Principal component analysis and Stochastic outlier selection in maximising the number of anomalies detected in local health regions. Because of this, we also provide the minimum number of machine learning models (top-k models) to maximise the number of anomalies detected across different health regions. We discovered that the top-3 models that maximise the coverage of the number and types of anomalies detected across the 13 health regions are: Principal component analysis, Stochastic outlier selection and Multi-covariance determinant. Anomaly detection approaches provide interesting solutions to discover patterns of epidemiological importance when confronted with a large volume of data across space and time. Our exploratory approach can be replicated for other diseases and locations to inform timely interventions and actions toward endemic disease control.

Piroplasmosis, caused by Babesia spp. and Theileria spp., poses significant constraints for livestock production and upgradation in Bangladesh. Besides examining blood smears, few molecular reports are available from some selected areas in the country. Therefore, the actual scenario of piroplasmosis in Bangladesh is deficient. This study aimed to screen the piroplasms in different livestock species by molecular tools. A total of 276 blood samples were collected from cattle, gayals (Bos frontalis) and goats in five geographies of Bangladesh. Thereafter, screening was conducted through a polymerase chain reaction, and species were confirmed by sequencing. The prevalence of Babesia bigemina, B. bovis, B. naoakii, B. ovis, Theileria annulata and T. orientalis was 49.28%, 0.72%, 1.09%, 32.26%, 6.52% and 46.01%, respectively. The highest prevalence (79/109; 72.48%) of co-infections was observed with B. bigemina and T. orientalis. The phylogenetic analyses revealed that the sequences of B. bigemina, B. bovis, B. naoakii, B. ovis and T. annulata were included in one clade in the respective phylogram. In contrast, the sequences of T. orientalis were separated into two clades, corresponding to Type 5 and 7. To the best of our knowledge, this is the first molecular report on piroplasms in gayals and goats in Bangladesh.

The shortwave infrared Ge-Si photodetector will become the core device of the LiDAR optical receiver. In order to meet the urgent demand for photodetectors in the LiDAR field, we have designed and produced a 32×32 pixel Ge-Si photodetector array proposed and developed to meet the performance requirements of the detector array. A dark current detection system for fast scanning and detecting large-scale Ge-Si detector arrays is proposed and developed to achieve rapid detection of dark current in each pixel of the detector. The system was used to validate the main performance indicators of the detector array we designed, achieving rapid discrimination of array performance and rapid localization of damaged pixels. The scanning test results show that the average dark current of the detector array chip we designed is at the nano ampere level, and the proportion of bad points is less than 1%. The consistency of the array chip is high, which can meet the requirements of light detection at the receiving end of the LiDAR. This work laid the foundation for our subsequent development of a LiDAR prototype system.

Background: Despite hearing aids adequately compensate for hearing loss, a substantial proportion of the population leave their hearing difficulties untreated. Even though this is a well-known clinical issue, the optimal approach to address this issue during the hearing rehabilitation process is still unclear. Purpose: The present study aims to characterise behavioural and neurophysiological auditory and cognitive processing skills in experienced hearing aid users versus those with normal hearing, aimed at providing clinicians with the evidence required to adequately manage the expectations of their clients, thus indirectly reinforcing hearing-aid adoption within the adult population with hearing loss. Research design: Behavioural tests included auditory, cognitive, and speech-in-noise tasks; and neurophysiological testing included cortical auditory evoked potentials evoked by a /da/ stimulus presented at 65 dB SPL. The tests were selected based on previous literature supporting specific speech-understanding skills. Study sample: Ten participants (7 female, 21—68 years) with bilateral, mild-moderate to moderately-severe sensorineural hearing loss (HL), and 10 with clinically normal hearing (NH, 8 female, 19—62 years) participated in the study. Data collection and analysis: Behavioural data was analysed using multivariate analysis of variance (MANOVA) and neurophysiological analysis used measurements such as independent t-test, time-frequency analysis and inter-trial phase coherence. Results: The NH and HL groups presented similar scores in all the behavioural tasks. Time-frequency analysis revealed a statistically significantly reduction in alpha (8–12 Hz) synchronisation at the centro-frontal electrodes in the HL group – a brain activity pattern that has been associated with listening effort, inhibition and selective attention. Conclusions and significance: Results support the conclusion that hearing aids are effective in compensating for the audibility of their users, enabling them to perform at similar levels than their normal-hearing peers. However, the reduced alpha synchronisation observed in the HL population indicates that adequate audibility does not extend to improved neural responses. Future studies need to investigate the induced activity in speech understanding paradigms to explore the auditory processing differences at cortical level. The results are only from a small sample size but the findings have the potential to support clinicians in managing adequately the expectations of their clients in regards the benefits of hearing aid technologies.

Intracranial hemorrhage is a serious medical problem that requires rapid and often intensive medical care. Identifying the location and type of any hemorrhage present is a critical step in the treatment of the patient. Diagnosis requires an urgent procedure, and the detection of hemorrhage is a difficult and time-consuming process for human experts. In this paper, we propose methods based on EfficientDet’s deep-learning technology that can be applied to the diagnosis of hemorrhages and thus become a decision-support system. Our proposal is two-fold. On the one hand, the proposed technique classifies slices of computed tomography scans for the presence hemorrhage or its lack, achieving 92.7% accuracy and 0.978 ROC-AUC. On the other hand, our methodology provides visual explanations of the classification chosen using the Grad-CAM methodology.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: describe briefly the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article, it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The paper investigates new robust code constructions based on bent functions and spline–wavelet transformation. Implementation of bent functions in codes construction increases the probability of error detection in the data channel and cryptographic devices. Meanwhile, use of spline–wavelets theory for constructing the codes gives the possibility to increase system security from the actions of an attacker. Presented constructions combines spline–wavelets functions and bent functions. Developed robust codes, compared to existing ones, have a higher parameter of maximum error masking probability. Illustrated codes are ensuring the security of transmitted information. Some of the granted constructions were implemented on FPGA.

Automatic ship detection provides an essential function towards maritime domain awareness for security or economic monitoring purposes. This work presents an approach for training a deep learning ship detector in Sentinel-2 multispectral images with few labeled examples. We design a network architecture for detecting ships with a backbone that can be pre-trained separately. By using Self Supervised Learning, an emerging unsupervised training procedure, we learn good features on Sentinel-2 images, without requiring labeling, to initialize our network’s backbone. The full network is then fine-tuned to learn to detect ships in challenging settings. We evaluated this approach versus pre-training on ImageNet and versus a classical image processing pipeline. We examined the impact of variations in the self-supervised learning step and we show that in the few-shot learning setting self-supervised pre-training achieves better results than ImageNet pre-training. When enough training data is available, our self-supervised approach is as good as ImageNet pre-training. We conclude that a better design of the self-supervised task and bigger non-annotated dataset sizes can lead to surpassing ImageNet pre-training performance without any annotation costs.

Personality is the most critical feature that tells us about an individual. It is the collection of the individual’s thoughts, opinions, emotions and more. Personality detection is an emerging field in research and Deep Learning models have only recently started being developed. There is a need for a larger dataset that is unbiased as the current dataset that is used is in the form of questionnaires that the individuals themselves answer, hence increasing the chance of unconscious bias. We have used the famous stream-of-consciousness essays collated by James Pennbaker and Laura King. We have used the Big Five Model often known as the five-factor model or OCEAN model. Document-level feature extraction has been performed using Google’s word2vec embeddings and Mairesse features. The processed data has been fed into a deep convolutional network and a binary classifier has been used to classify the presence or absence of the personality trait. Hold- out method has been used to evaluate the model, and the F1 score has been used as the performance metric.

We report on an immunofluorescent paper-based assay for the detection of severe acute respiratory symptom coronavirus 2 (SARS-CoV-2) humanized antibody. The paper-based device was fabricated by using lamination technique for easy and optimized handling. Our approach utilises a two-step strategy that involves (i) initial coating of the paper-electrode with recombinant SARS-CoV-2 nucleocapsid antigen to capture the target SARS-CoV-2 specific antibodies, and (ii) subsequent detection of SARS-CoV-2 antibodies using fluorophore-conjugated IgG antibody. The fluorescence readout was observed with fluorescence microscopy. The images were processed and quantified using a MATLAB program. The assay can selectively detect SARS-CoV-2 humanized antibodies spiked in PBS and healthy human serum samples with the relative standard deviation of approximately 6.4% (for n = 3). It has broad dynamic ranges (1 ng to 50 ng/µL in PBS and 5 to 100 ng/µL in human serum samples) for SARS-CoV-2 humanized antibodies with the detection limits of 2 ng/µL (0.025 IU/mL) and 10 ng/µL (0.125 IU/mL) in PBS and human serum samples, respectively. We believe that our assay has the potential to be used as a simple, rapid, and inexpensive paper-based diagnostic device with a portable fluorescent reader to provide point-of-care diagnosis. This assay can be used for rapid examination of a large batch of samples toward clinical screening of SARS-CoV-2 specific antibodies as a confirmed infected active case or to evaluate the immune response to a SARS-CoV-2 vaccine.

As air traffic demand grows, robust, data-driven anomaly detection methods are required to ensure that aviation systems become safer and more efficient. The terminal airspace is identified as the most critical airspace for both individual flight-level and system-level safety and efficiency. As such, developing data-driven anomaly detection methods to analyze terminal airspace operations is paramount. With the expansion of ADS-B technology, open-source flight tracking data has become more readily available to enable larger-scale analyses of aircraft operations. This paper makes a distinction between spatial metrics in ADS-B trajectory data and energy metrics derived from ADS-B trajectory data. Motivated by the limited number of approaches that simultaneously consider both spatial and energy metrics, this paper introduces the concepts of spatial anomalies and energy anomalies. In particular, it proposes a novel, unified framework for detection of spatial and energy anomalies in ADS-B trajectory data (and associated derived metrics). The framework consists of three main parts - a data processing procedure, a spatial anomaly detection method, and an energy anomaly detection method. The framework is demonstrated utilizing four months of ADS-B trajectory data associated with arrivals at San Francisco International Airport, and the relationship between the spatial and energy anomalies in this terminal airspace is explored. The results that stem from the implementation of this framework indicate that if an aircraft is spatially not conforming to an identified set of air traffic flows representing standard spatial operations, then this aircraft is more likely to experience non-conformance to standard operations in its energy metrics. Aviation operators, such as air traffic controllers, may benefit from this observation, as it may factor into decision-making in instances where there is the potential to instruct an aircraft to spatially deviate from standard operations. Additionally, this research revealed underlying differences between trajectories that are spatially nominal yet energy-anomalous and those trajectories that are spatially anomalous and energy-anomalous. Focusing solely on energy anomaly detection does not provide insight into potential spatial-related decisions that may have been made to result in off-nominal energy behavior.

Abstract: Imaging devices of less than 300,000 pixels are mostly used for sewage conduit exploration due to the petty nature of the survey industry in Korea. P articular ly , devices of less than 100,000 pixels are still widely used, and the environment for image processing is very bitter . Since the sewage conduit image s covered in this study ha ve a very low resolution (240 × 320 = 76,800 pixels), it is very difficult to detect cracks. Because most of the resolution of the sewe r conduit images are very low in Korea, this problem of low resolution was selected as the subject of study. Cracks were detected through a total of six steps of improving the crack in Step 2, finding the optimal threshold value in Step 3, and applying an algorithm to detect cracks in Step 5. Cracks were effectively detected by the optimal parameters in Steps 2 and 3 and the user algorithm in Step 5. Desp ite the very low resolution, the cracked image s showed 96.4% accuracy of detection, and the non cracked image s showed 94.5% accuracy . Moreover, the analysis was excellent in quality , also . It is believed that the findings of this study can be effectively u sed for crack detection with low resolution images.

Biosensors are essential tools which have been traditionally used to monitor environmental pollution, detect the presence of toxic elements and biohazardous bacteria or virus in organic matter and biomolecules for clinical diagnostics. In the last couple of decades, the scientific community has witnessed their widespread application in the fields of military, health care, industrial process control, environmental monitoring, food-quality control, and microbiology. Biosensor technology has greatly evolved from the in vitro studies based on the biosensing ability of organic beings to the highly sophisticated world of nanofabrication enabled miniaturized biosensors. The incorporation of nanotechnology in the vast field of biosensing has led to the development of novel sensors and sensing mechanisms, as well as an increase in the sensitivity and performance of the existing biosensors. Additionally, the nanoscale dimension further assists the development of sensors for rapid and simple detection in vivo as well as the ability to probe single-biomolecules and obtain critical information for their detection and analysis. However, the major drawbacks of this include, but are not limited to potential toxicities associated with the unavoidable release of nanoparticles into the environment, miniaturization induced unreliability, lack of automation, and difficulty of integrating the nanostructured-based biosensors as well as unreliable transduction signals from these devices. Although the field of biosensors is vast, we intend to explore various nanotechnology enabled biosensors as part of this review article and provide a brief description of their fundamental working principles and potential applications.

A dual-platform colorimetric and ratiometric chemosensor, namely 6-(2-hydroxynaphthalen)-N-n-butyl-naphthalimide (HNA), based on Schiff base constructed from N-n-butyl-4-amino-1,8-naphthalimide and 2-hydroxy-1-naphthaldehyde has been designed and fabricated for detecting fluoride anion (F−) in DMSO solution. HNA is a colorimetic and ratiometric probe with superior selectivity and sensitivity. The color changes of HNA from yellow to purple was observed by the naked eyes in the presence of F−. The absorbance in the UV-Vis spectra of HNA was decreasing in 422 nm, while gradually increasing in 583 nm by adding F−. The limit of detection (LOD) of HNA for detecting F− is low to 0.61 μM and the binding model of HNA and F− is in 3:2 stoichiometry. Meanwhile, HNA can be used to detect F− in real samples. Finally, the mechanism of HNA for the detection of F− was investigated. The present work indicated that HNA would be a superior potential chemosensor in monitoring F− selectively and sensitively.

Amplitude modulation (AM) is a characteristic feature of wind farm noise and has the potential to contribute to annoyance and sleep disturbance. This study aimed to develop an AM detection method using a random forest approach. The method was developed and validated on 6,000 10-second samples of wind farm noise manually classified by a scorer via a listening experiment. Comparison between the random forest method and other widely-used methods showed that the proposed method consistently demonstrated superior performance. This study also found that a combination of low-frequency content features and other unique characteristics of wind farm noise play an important role in enhancing AM detection performance. Taken together, these findings support that using machine learning-based detection of AM is well suited and effective for in-depth exploration of large wind farm noise data sets for potential legislative and research purposes.

Malware analysis is fundamental for defending against prevalent cyber security threats, and requires a means to deploy and study behavioural software traits as more sophisticated malware is developed. Traditionally, virtual machines are used to provide an environment that is isolated from production systems so as to not cause any adverse impact on existing infrastructure. Malware developers are fully aware of this and so will often develop evasion techniques to avoid detection within sandbox environments. In this paper, we conduct an investigation of anti-evasion malware triggers for uncovering malware that may attempt to conceal itself when deployed in a traditional sandbox environment. To facilitate our investigation, we developed a tool called MORRIGU that couples together both automated and human-driven analysis for systematic testing of anti-evasion methods using dynamic sandbox reconfiguration techniques. This is further supported by visualisation methods for performing comparative analysis of system activity when malware is deployed under different sandbox configurations. Our study reveals a variety of anti-evasion traits that are shared amongst different malware families, such as sandbox `wear-and-tear', and Reverse Turing Tests (RTT), as well as more sophisticated malware samples that require multiple anti-evasion checks to be deployed. We also perform a comparative study using Cuckoo sandbox to demonstrate the limitations of adopting only automated analysis tools, to justify the exploratory analysis provided by MORRIGU. By adopting a clearer systematic process for uncovering anti-evasion malware triggers, as supported by tools like MORRIGU, this study helps to further the research of evasive malware analysis so that we can better defend against such future attacks.

Paper-based microfluidic analysis devices (μPADs) have attracted attention as a cost-effective platform for point-of-care testing (POCT), food safety, and environmental monitoring. Recently, three-dimensional (3D)-μPADs have been developed to improve the performance of μPADs. For accurate diagnosis of diseases, however, 3D-μPADs need to be developed to simultaneously detect multiple biomarkers. Here, we report a 3D-μPADs platform for the detection of multiple biomarkers that can be analyzed and diagnosed with a smartphone. The 3D-μPADs were fabricated using a 3D digital light processing printer and consisted of a sample reservoir (300 µL) connected to 24 detection zones (of 4 mm in diameter) through 8 microchannels (of 2 mm in width). With the smartphone application, eight different biomarkers related to various diseases were detectable in concentrations ranging from normal to abnormal conditions: glucose (0–20 mmol/L), cholesterol (0–10 mmol/L), albumin (0–7 g/dL), alkaline phosphatase (0–800 U/L), creatinine (0–500 µmol/L), aspartate aminotransferase (0–800 U/L), alanine aminotransferase (0–1000 U/L), and urea nitrogen (0–7.2 mmol/L). These results suggest that 3D-µPADs can be used as a POCT platform for simultaneous detection of multiple biomarkers.

Scattering hyperspectral technology is a nondestructive testing method with many advantages. Here, we propose a method to improve the accuracy of egg freshness, research the influence of incident angles of light source on the accuracy and explain its mechanism. A variety of weak classifiers classify eggs based on the spectra after preprocessing and feature wavelength extraction to obtain three classifiers with the highest accuracy. The three classifiers are used as metamodels of stacking ensemble learning to improve the highest accuracy from 96.25% to 100%. Moreover, the highest accuracy of scattering, reflection, transmission and mixed hyperspectral of eggs are 100.00%, 88.75%, 95.00% and 96.25%, respectively, indicating that the scattering hyperspectral for egg freshness detection is better than that of the others. In addition, the accuracy is inversely proportional to the angle of incidence due that the smaller the incident angle, the camera collects a larger proportion of scattering light, which contains more biochemical parameters of an egg than that of reflection and transmission. These results are very important for improving the accuracy of non-destructive testing and selecting the incident angle of the light source, and have potential applications in online non-destructive testing.

Face recognition is a valuable forensic tool for criminal investigators since it certainly helps in identifying individuals in scenarios of criminal activity like fugitives or child sexual abuse. It is, however, a very challenging task as it must be able to handle low-quality images of real world settings and fulfill real time requirements. Deep learning approaches for face detection have proven to be very successful but they require a large computation power and processing time. In this work, we evaluate the speed-accuracy tradeoff of three popular deep-learning-based face detectors on the WIDER Face and UFDD data sets in several CPUs and GPUs. We also develop a regression model capable to estimate the performance, both in terms of processing time and accuracy. We expect this to become a very useful tool for the end user in forensic laboratories in order to estimate the performance for different face detection options. Experimental results showed that the best speed-accuracy tradeoff is achieved with images resized to 50% of the original size in GPUs and images resized to 25% of the original size in CPUs. Moreover, performance can be estimated using multiple linear regression models with a Mean Absolute Error (MAE) of 0.113 what is very promising for the forensic field.

In tracking-by-detection paradigm for multi-target tracking, target association is modeled as an optimization problem that is usually solved through network flow formulation. In this paper, we proposed combinatorial optimization formulation and used a bipartite graph matching for associating the targets in the consecutive frames. Usually, the target of interest is represented in a bounding box and track the whole box as a single entity. However, in the case of humans, the body goes through complex articulation and occlusion that severely deteriorate the tracking performance. To partially tackle the problem of occlusion, we argue that tracking the rigid body organ could lead to better tracking performance compared to the whole body tracking. Based on this assumption, we generated the target hypothesis of only the spatial locations of person’s heads in every frame. After the localization of head location, a constant velocity motion model is used for the temporal evolution of the targets in the visual scene. Qualitative results are evaluated on four challenging video surveillance dataset and promising results has been achieved.

Auto checkout has received more and more attention in recent years and this system automatically generates a shopping bill by identifying the picture of the products purchased by the customers. However, the system is challenged by the domain adaptation problem, where each image of the training set contains only one commodity, whereas the test set is a collection of multiple commodities. The existing solution to this problem is to resynthesize the training images to enhance the training set. Then the composite images are rendered using CycleGAN to make the image distribution of the training set and the test set more similar. However, we find that the detection boxes given by the ground truth of the common dataset contain a large part of the background area, the area will affect the training process as noise. To solve this problem, we propose a mask data priming method. Specifically, we redo the large scale Retail Product Checkout (RPC) dataset and add segmentation annotation information to each item in the training set image based on the original dataset using pixel-level annotation. Secondly, a new network structure is proposed in which we train the network using joint learning of detectors and counters, and fine-tune the detection network by filtering out suitable images from the test set. Experiments on the RPC dataset have shown that our method yields better results. we used an approach that reached 81.87% compared to 56.68% for the baseline approach which demonstrates that pixel-level information helps to improve the detection results of the network.

There is a new public health crisis threatening the world with the emergence and spread of novel coronavirus (SARS-CoV-2). The outbreak of coronavirus disease 2019 (COVID-19), which originated in Wuhan, China, in December 2019, has been declared a public health emergency of international concern by WHO. Most patients infected with SARS-CoV-2 exhibited symptoms of fever, cough, myalgia, fatigue and shortness of breath. Many infected people may be asymptomatic. It is generally believed that airway exposure to respiratory droplets from an infected patient is the main transmission route of this disease. However, apart from respiratory source, other source specimens like faecal matter and urine could be possible for COVID-19 infectivity. The spreading other routes of the virus has been alarming sign, both for public and health care professionals. Understanding the spreading routes of SARS-CoV-2 is crucial for patient management and defining biosafety strategies for public and health care workers.