Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

This paper evaluates norms and assesses the level of knowledge in air conditioning project management within the construction industry. A total of 25 questions were distributed to multiple candidates, who were filtered based on pre-established inclusion and exclusion criteria. Thirty-nine candidates were ultimately approved to participate in the survey. The questions were designed to address five hypotheses, with each set of five questions corresponding to one hypothesis. The results were obtained after pre-processing the data using Matlab software. The data was pre-processed using Matlab software, and the results were analyzed using the Delphi method. The analysis revealed that only two hypotheses were approved: No matter whether there are nationalized safety rules or not, the impact of data sciences and smart technologies, including air conditioning management systems, is critical for human life in the building business.

Diatom assemblages in mud volcanoes are quite rare and poorly studied. The finding of a rich diatom flora in the sediments of the Daginsky Mud Volcano (DMV), located in the tidal zone of the Nyisky Bay of the Sea of Okhotsk, is interesting for studying the conditions for the formation of host sediments in the zone of influence of various extreme factors, such as outflows of gases and water-mud mass, thermal springs, and tides, etc. For this purpose, the composition of diatoms and their concentration in DMV sediments were studied, a comparison was made with diatoms of geothermal springs of the Russian Far East associated with volcanic activity, and the stratigraphic distribution of the found extinct diatoms was analyzed, which is important for determining their source and age of mud volcano roots. Diatom assemblages from DMV sediments are mainly characterized by the predominance of Metascolioneis tumida, Paralia sulcata, Odontella aurita, Pinnunavis yarrensis, Petroneis marina, Cocconeis scutellum, and Navicula digitoradiata. They consist of diatoms of different biotopes and extinct species. The diversity and abundance of brackish water and marine species indicates the predominant influence of sea waters on the formation of DMV sediments. The diverse freshwater species were mainly introduced into sediments with river runoff, but it is likely that some of them, cosmopolitan alkaliphilic species, are inhabitants of geothermal springs. The presence of extinct species from the underlying Neogene sediments from where they were carried with gas-water-mud masses, is the most typical for diatom assemblages of the DMV.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal-vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR>TSR>VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology is used to study how the initial residual stress in the blank will cause the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method is applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method is used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters is studied.

Metals are indispensable in the life of all organisms, in fact, their dysregulation causes various disorders caused by an interruption of their homeostasis. Nowadays different transition metals are incorporated into pharmaceutical products as diagnostic and therapeutic agents because of their electronic structure which gives them versatility in terms of tuning molecule properties, differently from organic molecules. Hence the interest in the study of metal-drug complexes from different points of view was born and many approaches were developed for the characterization, activation, delivery and molecular mechanisms clarification. The integration of these different approaches starting from chemoproteomics passing through nanoparticle systems to different activation strategies allows the understanding of the cellular responses of metallic drugs, which can be the basis for the design of new drugs and/or modification of drugs currently in use. This review aims to briefly summarize the recent advances in this area by describing the technological platforms and their possible applications to identify protein targets for discovering the mechanisms of action of metallodrugs, and to improve their efficiency in terms of administration.

Deforestation is an important environmental problem in México and a key promoter of regional climate change through modifying the surface albedo. The objective of this research was to characterize the impact of deforestation and land use changes on surface albedo (α) and climate patterns in the Municipality of Tapalpa, Jalisco, México between the years 2014 and 2021. The main land cover types are coniferous forests (CF), oak and gallery woodlands (OGW), and annual agriculture (AA); which represent more than 88% of the regional territory (1066.03 km2). We used 2014 and 2021 Landsat 8 OLI images with topographic and atmospheric correction, in order to develop an inventory of albedo values for each land cover type in both time scenarios. Albedo images were generated by using the equation proposed by Liang in 2001, which is based on the reflectance of the bands 2, 3, 4, 5, and 7. Differences in albedo values were calculated between the years 2014 and 2021, and those differences were correlated with variations in climate parameters, for which we used climate data derived from the WRF model. In addition, the different land use changes found were classified in terms of triggers for increasing or decreasing surface albedo. Results showed that between 2014 and 2021, at least 38 events of land use change or deforestation occurred, with albedo increments between 1 and 11%, which triggered an average increment of 0.57% of the regional surface albedo in comparison to 2014 scenario. From 2014 to 2021, the albedo for CF, OGW, and AA, increased significantly (p<0.001; Mann-Whitney U Test) by 79, 12, and 9%, respectively. In addition, the regional albedo increment was found to be significant and negatively correlated (p<0.01 Spearman’s coefficient) with relative humidity (RH), maximum temperature (Tmax), minimum temperature (Tmin), and diurnal thermal range (DTR). The decrease in the regional values of relative humidity in 2021, occurred even when in that year the annual precipitation levels were higher than those of 2014, hence, reinforcing the fact of a possible climatic effect of the regional albedo changes. Conversion of CF and OGW into AA, perennial agriculture (PA), or grassland (GR) always yielded an albedo increment, whilst the conversion of AA to irrigation agriculture or PA triggered a decrease in albedo, and finally, the pass from GR or AA to protected agriculture caused albedo increase or decrease, depending on the greenhouse covers materials. Reducing deforestation of CF and OGW, conversion of AA or GR into PA, and selecting adequate greenhouse covers could help to mitigate regional climate change.

The preparation of transition metal salt ammine complexes having oxidizing anions is a great challenge due to the reaction between the ammonia and oxidizing anions during the synthesis of these materials. However, they have an important role in the development of new oxidants in organic chemistry and especially as precursors in the preparation of mixed metal oxides and alloys in controlled temperature thermal decomposition reactions. Therefore, the synthetic procedures to prepare the complexes of transition metal permanganate, pertechnetate, and perrhenate (VIIB group tetraoxometallates) salts with ammonia as ligand or co-ligand have been comprehensively reviewed. The available data about the structure and spectroscopic properties of these compounds, including the hydrogen bonds that act as redox reaction centers under their thermal decomposition are given and evaluated. Their thermal decomposition processes and products have been summarized. The available pieces of information about their role in organic oxidation reactions like the oxidation of benzyl alcohols, and regeneration of oxo-compounds from oximes and phenylhydrazones including the kinetics of these processes have also been collected.

The ordered Ca3TaGa3Si2O14 and disordered La3Ga5SiO14 crystals of the lantangallium silicate family were grown by the Czochralski method. The independent coefficients of thermal expansion of crystals αc and αa were determined by X-ray powder diffraction based on the analysis of X-ray diffraction spectra measured in the temperature range of 25÷1000°C. It is shown that in the temperature range of 25÷800°C the thermal expansion coefficients are linear. At temperatures above 800°C there is a nonlinear character of the thermal expansion coefficients associated with a decrease in the Ga content in the crystal lattice of the lantangallium silicate family crystals.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

This paper focuses on the comparative analysis of lithium-ion batteries (LIB) thermal management with aim to maintain working temperature in the range 15 ℃ – 35 ℃. This is to prevent thermal runaway and high temperature gradients. The proposed approach is to employ the biodiesel, situated inside the diesel/LIB powered hybrid electric vehicle, to supply as fuel and coolant. A 3S2P LIB module is simulated using Ansys-Fluent CFD software tool. The system without a coolant shows that LIB has exceeded the optimum maximum temperature, which leads to shortened life-cycle and poor performance. Four fatty acid methyl ester biodiesels are used as coolants, namely palm, karanja, jatropha, and mahua oils. When compared with conventional methods of cooling, using air and 3M Novec liquid, the palm biodiesel coolant proves to be the best option to maintain LIB temperature within the optimum working range. With the use of palm biodiesel, the system is estimated to lightweight the BTMS by 43%, compared to the case when 3M Novec is used to maintain the same temperature range.

The path towards decarbonization requires a progressive adaptation of all refrigeration systems, but only stationary ones have been intensely studied to improve their environmental performance. However, refrigerated transport is a vital piece of the cold chain, and it must be considered in the green transition. In this paper, we propose a model for a hybrid refrigerated van that includes photovoltaic panels and electric batteries to decrease total greenhouse gas emissions from the engine. Thermal, electrical, and battery sub-models are considered and integrated into the comprehensive hybrid solar-powered refrigerated van model. Different technologies are compared in economic terms, including Lithium and Lead-acid batteries and three different types of photovoltaic panels. The model was validated regarding van fuel consumption, showing a 4% deviation. Single and multiple delivery scenarios are considered to assess the energetic, economic, and environmental benefits. Monthly CO2,e emissions could be reduced to 20% compared to a standard refrigerated van. Despite the environmental benefits provided by this sustainable solution, the payback period is still too long (above 20 years) because of the necessary investment to adapt the vehicle and considering fuel and electricity prices currently.

Artificial roughness applied to the Solar Air Heater (SAH)’s absorber plate is a popular technique to increase its total-thermal efficiency (η_(t-th)). In this paper, the influence of geometrical parameters of V-down ribs attached below the corrugated absorbing plate of SAH on the η_(t-th) has been examined. The impacts of key roughness parameters, including relative pitch p⁄e (6-12), relative height e⁄D (0.019-0.043), angle of attack α (30°-75°), and Re (1000-20000), are examined under real weather conditions. The SAH η_(t-th) roughened by V-down ribs is predicted using an in-house developed conjugate heat transfer numerical model. It has been shown that the maximum SAH η_(t-th) is 78.8%, predicted under steady-state conditions of Re = 20000, solar irradiance G =1000 W/m2, p/e = 8, e/D = 0.043, and angle =60. That is 15.7% more efficient than that of the default smooth surface. Under real weather condition, the η_(t-th) of the roughened SAH with single and double glass covers are 17.7% and 20.1%, respectively, higher than those of smooth SAH.

Calcium dihydrogen phosphate monohydrate [Ca(H2PO4)2·H2O] (a fertilizer) was successfully synthesized by the recrystallization process by using a prepared triple superphosphate (TSP) that derived from oyster shell waste as starting material. This bio-green, eco-friendly process to produce an important fertilizer can promote a sustainable society. The shell-waste-derived TSP was dissolved in distilled water and kept at 30, 50, and 80 °C. Non-soluble powder and TSP solution were obtained. The TSP solution fraction were then dried and the recrystallized products (RCP30, RCP50, and RCP80) were obtained and confirmed as Ca(H2PO4)2·H2O. Whereas the non-soluble products (NSP30, NSP50, and NSP80) were observed as calcium hydrogen phosphate dihydrate (CaHPO4·2H2O). The recrystallized yields of RCP30, RCP50, and RCP80 were found to be 51.0%, 49.6%, and 46.3%, whereas the soluble percentages were 98.72%, 99.16%, and 96.63%, respectively. RCP30 shows different morphological plate sizes, while RCP50 and RCP80 present the coagulate crystal plates. X-ray diffractograms confirm the formation of both the NSP and RCP. The infrared adsorption spectra confirmed the vibrational characteristics of HPO42‒, H2PO4‒ and H2O existed in CaHPO4·2H2O and Ca(H2PO4)2·H2O. Three thermal dehydration steps of Ca(H2PO4)2·H2O (physisorbed water, polycondensation, and re-polycondensation) were observed. Ca(H2PO4)2 and CaH2P2O7 are the thermodecomposed products from the first and second steps, whereas the final product is CaP2O6.

The physicalchemistry properties and crystal structure of were nano-ZrO₂+3mol.%Y₂O₃ determined. The kinetics of the formation of H₂ as a result of the decomposition of H₂O on the surface of nano-ZrO₂+3mol.%Y₂O₃ was studied. Effects of adsorption and desorption process on ZrO₂+3 mol.%Y₂O₃ nanoparticles were studied at different (T=400÷1000⁰C) temperature. The study of H₂ in thermal processes at nano-ZrO₂+3 mol.%Y₂O₃ system increased. Such an increase in H₂ generation in comparison with a pure H₂O as thermal processes had formedactive centers for H₂O decomposition on the surface of the catalyst at the expense of δ-electrons emitted on the surface of nano-ZrO₂+3 mol.%Y₂O₃. This showed that the dimensions of the studied nanoscale particles systems are comparable to the free running distance of energy carriers generated by of nano-ZrO₂+3 mol.%Y₂O₃ as a result of thermal processes. These results are promising for hydrogen generation by waer spliting in near future.

Logic gates made of pairs of NPN and PNP bipolar transistors, similar to CMOS logic gates, have been proposed and patented long ago but did not find any practical application until now. Other bipolar technologies (TTL, TTL-S, ECL), once the technologies of choice for digital systems, were abandoned and superseded by CMOS. In this paper it is shown that now, when truly com-plementary pairs of bipolar transistors can be made, properly biased bipolar gates similar to CMOS gates are feasible, can be thermally stable and find practical applications.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

Thermodynamics has been the foundation of many models of biological and technological systems. But thermodynamics is static and is misnamed. A more suitable name is thermostatics. Thermostatics does not include time as a variable and so has no velocity, flow or friction. Indeed, as usually formulated, thermostatics does not include boundary conditions. Devices require boundary conditions to define their input and output. They usually involve flow and friction. Thermostatics is an unsuitable foundation for understanding technological and biological devices. A time dependent generalization of thermostatics that might be called thermal dynamics is being developed by Chun Liu and collaborators to avoid these limitations. Electrodynamics is not restricted like thermostatics, but in its classical formulation involves drastic assumptions about polarization and an over-approximated dielectric constant. Once the Maxwell equations are rewritten without a dielectric constant, they are universal and exact. Conservation of total current, including displacement current, is a restatement of the Maxwell equations that leads to dramatic simplifications in the understanding of one dimensional systems, particularly those without branches, like the ion channel proteins of biological membranes and the two terminal devices of electronic systems. The Brownian fluctuations of concentrations and fluxes of ions become the spatially independent total current, because the displacement current acts as an unavoidable low pass filter, a consequence of the Maxwell equations for any material polarization. Electrodynamics and thermal dynamics together form a suitable foundation for models of technological and biological systems.

Research on urban heat mitigation has been growing in recent years with many of the studies focusing on green infrastructure (GI) as a strategy to mitigate the adverse effects of Urban Heat Island (UHI). This paper aims at presenting a review of the range of findings from GI research for urban heat mitigation through a review of scientific articles published during the years 2009-2019. This research includes a review of the different types of GI and its contribution for urban heat mitigation and human thermal comfort. In addition to analyzing different mitigation strategies, numerical simulation tools that are commonly used are also reviewed. It is seen that ENVI-met is one of the modelling tools that is considered as a reliable tool to simulate different mitigation strategies and hence has been widely used in the recent past. Considering its popularity in urban microclimate studies, this article also provides a review of ENVI-met simulation results that were reported in the reviewed papers. It was observed that the majority of the research was conducted on a limited spatial scale and focused on temperature and human thermal comfort.

In this study, differences in the kinetics of thermal-supported hydrolytic degradation of poly(lactic acid) (PLA) sample wet spinning fibres due to material variance in the initial molecular and supramolecular structure were analysed. The investigation was carried out at the microstructural and molecular levels by using readily available methods such as scanning electron microscopy, mass erosion measurement and estimation of intrinsic viscosity. The results show a varying degree of influence of the initial structure on the degradation rate of studied PLA fibres. The experiment shows that hydrolytic degradation at a temperature close to the cold crystallization temperature on a macroscopic level is definitely more rapid for the amorphous material, while on a molecular scale it is similar to a semi-crystalline material. Further, for the adopted degradation temperature of 90 °C, a marginal influence of pH of the degradation medium on the degradation kinetics was also demonstrated

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

Although the majority of mobile phone (MP) users do not attribute adverse effects on health or well-being to MP-emitted radiofrequency (RF) electromagnetic fields (EMFs), the exponential increase in the number of RF devices necessitates continuing research aimed at the objective investigation of such concerns. In this work, we investigate the effects of acute exposure from Long Term Evolution (LTE) MP EMFs on thermal pain threshold in healthy young adults. We use a protocol that was validated in a previous study in a capsaicin-induced hyperalgesia model, and was also successfully used to show that exposure from an RF source mimicking a Universal Mobile Telecommunications System (UMTS) MP led to mildly stronger desensitization to repeated noxious thermal stimulation relative to the sham condition. Using the same experimental design, we did not find any effects of LTE exposure on thermal pain threshold. The present results are in accordance with previous evidence suggesting that effects are likely to be placebo/nocebo effects and are unrelated to the brief acute LTE EMF exposure itself. The fact that this is dissimilar to our previous results on UMTS exposure implies that RF modulations might differentially affect pain perception, and points to the necessity of further research in the topic.

Transparent electrodes (TEs) made of metallic nanowires, such as Ag, Au, Cu, and Ni, have attracted rising attention for several reasons: 1) they can act as a substitute for tin oxide-based TEs such as indium-tin oxide (ITO) and fluorine-doped tin oxide (FTO); 2) various methods exist for fabricating such TEs such as filtration, spraying and meyer bar coating; 3) greater compatibility with different substrates can be achieved due to the variety of fabrication methods; and 4) extra functions in addition to serving as electrodes, such as catalytic abilities, can be obtained due to the metals that compose the TEs. There are a large number of applications for TEs, ranging from electronics and sensors to biomedical devices. This short review is a summary of recent progress, mainly during the past five years, on silver nanowire-based TEs. The focus of the review will be on theory development, mechanical, chemical and thermal stability and optical properties. The many applications of TEs are outside the scope of this review.

Background: Post-operative pain and swelling are frequently observed after sinus lift procedures. The aim of the present study was a clinical evaluation of swelling and pain of two sinus lift different flaps technique measured through visual analogue scale (VAS), verbal rating scale (VRS) and infrared thermal imaging (i.e., thermography). Methods: A randomized controlled trial was conducted in fifteen patients treated for a total of 30 sinus randomly allotted into two groups. In patients of Group I, a triangular flap was performed, while in Group II modified triangular flap without anterior release was performed. Postoperative pain was scored by VAS and inflammation was recorded by VRS at 2, 4, 6 and 14 days. The facial temperature was recorded before and after sinus augmentation, at 2, 4, 6 day intervals for the first week and at 14 day, to check the course of healing. Results: In group I the pain intensity was recorded at 2 days after the surgery with a score of 38.67 ± 6.4 mm. Swelling was higher at 2 and 4 day, and it was absent at day 6. Facial temperature difference before and after the procedure was 3 (4.737 °C ± 0.37). In Group II the pain was lower than in Group I (p < 0,05). Swelling scored 2 on the first and second day, and it was reduced at day 4. After the second day the difference of temperature reduced significantly compared to day of surgery (0.77 °C), at 2 and 4 days no difference was registered. Conclusion: In conclusion based on the outcome of the present study, modified triangular flap can be used with success in sinus augmentation procedures and is to be preferred to trapezoidal flap.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

Had magnetic monopoles been ubiquitous as electrons do, we would have probably had a different form of matter, and power plants based on currents of these magnetic charges would have been a familiar scene of modern technology. Magnetic dipoles do exist however, and in principle one could wonder if we can use them to generate magnetic currents. In the present work, we discuss the issue of generating magnetic currents and magnetic thermal currents in electrically-insulating low-dimensional Heisenberg antiferromagnets by invoking the (broken) electricity-magnetism duality symmetry. The ground state of these materials is a spin-liquid state that can be described well via the Jordan-Wigner fermions, which permit an easy definition of the magnetic particle and thermal currents. The spin-liquid states in these antiferromagnets are either gapless or gapped liquids of spinless fermions whose flow defines a current just as the one defined for electrons in a Fermi liquid. The driving force for the magnetic current is a magnetic field with a gradient along the magnetic conductor. The present work is about claiming that what the experiments in spintronics attempt to do is trying to treat the magnetic degrees of freedoms on the same footing as the electronic ones.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Recycling of composite materials has become a very important topic to develop sustainable solutions for the management of waste generated by industries that use composite materials. This paper presents a bibliographical review on the main recycling methods of composite materials such as: mechanical, chemical, thermal and hybrid. In mechanical recycling, the material is crushed or ground, generally using the resulting material as filler, which causes limitations in the applications due to the type of resulting fibers (short, long, non-uniform). On the other hand, chemical recycling breaks down polymers through a chemical reaction and recovers fibers, so in some cases the mechanical properties of the fibers are affected. Thermal recycling uses high temperatures to break down materials, transforming them into energy or reusing them in other products. Finally, hybrid recycling uses two or more processes as a means to recover the material; among the most used methods in this category is the mechanical process combined with the thermal process. This review describes the advantages and disadvantages of each method, as well as the environmental impact. Although each type of recycling offers special characteristics for the material obtained, it is necessary to continue researching and developing technologies for recycling processes that promote recycling and reuse of composite materials in a better way.

Hybrid nanocomposites have emerged as a groundbreaking class of materials in the aerospace industry, offering exceptional mechanical, thermal, and functional properties. These materials, composed of a combination of metallic matrices reinforced with a mixture of nanoscale particles, such as carbon nanotubes (CNTs), graphene, and ceramic nanoparticles (SiC, Al2O3), provide a unique balance of high strength, low weight, and enhanced durability. Recent advances in developing these nanocomposites have focused on optimizing the dispersion and integration of nanoparticles within the matrix to achieve superior material performance. Innovative fabrication techniques have ensured uniform distribution and strong bonding between the matrix and the reinforcements, including advanced powder metallurgy, stir casting, in-situ chemical vapor deposition (CVD), and additive manufacturing. These methods have enabled the production of hybrid nanocomposites with improved mechanical properties, such as increased tensile strength, fracture toughness, wear resistance, and enhanced thermal stability and electrical conductivity. Despite these advancements, challenges remain in preventing nanoparticle agglomeration and ensuring consistent quality and repeatability in large-scale production. Addressing these issues is critical for fully leveraging the potential of hybrid nanocomposites in aerospace applications, where materials are subjected to extreme conditions and rigorous performance standards. Ongoing research is focused on developing novel processing techniques and understanding the underlying mechanisms that govern the behavior of these materials under various operational conditions. This review highlights the recent progress in the design, fabrication, and application of hybrid nanocomposites for aerospace applications. It underscores their potential to revolutionize the industry by providing materials that meet the demanding requirements for lightweight, high-strength, and multifunctional components.

It’s very well known that the world's attention is currently focused on the energy transition. The energy security, in addition to the drive to reduce greenhouse gas emissions in order to limit global warming, and the generalization of the access to energy, have contributed to adoption of the Moroccan Energy Strategy with a strong focus on Renewable Energies (RE). Morocco is notoriously poor in conventional fossil primary energy resources with an energy dependence on the order of 90%. The energy crisis and that resulted from Covid-19 pandemic and the geopolitical conflicts, combined compounded with steady increase in demand have heavily affected the security and the stability of the country's energy situation. The transition to RE, by strongly engaging in the implementation of several solar, wind and hydro energy projects benefiting from the country's excellent solar and wind energy potential, has made the country the leader in RE in Africa. By 2030, the share of RE in the installed capacity is expected to reach 52%. In this work, an overview of the current situation of RE (particularly solar energy) in Morocco is provided, including, the potentials, obstacles and challenges, and future perspectives. Thanks to its high solar potential location, it’s predictable that Morocco effort will be focused on this field: the Erasmus Plus Innomed Project is a virtuous example of international cooperation, aiming at create a Solar Energy Network, in synergy with EU Partners.

The StarDICE experiment strives to establish an instrumental metrology chain with a targeted accuracy of 1 mmag in griz bandpasses to meet the calibration requirements of next-generation cosmological surveys. Atmospheric transmission stands out as a significant source of systematic uncertainty. Specifically, gray extinction induces spurious variations of photometric fluxes. We propose a solution relying on an uncooled long-wave infrared thermal camera to evaluate it. This type of camera can provide real-time insights into atmospheric conditions and detect cirrus clouds. However, achieving accurate measurements with thermal imaging systems necessitates prior calibration due to the influence of temperature-induced effects, which compromise their spatial and temporal precision. Moreover, these systems cannot provide scene radiance values in physical units by default. This study introduces a new calibration process utilizing a tailored forward modeling approach. The method is applied to an uncooled FLIR Tau2 thermal camera. It incorporates sensor, housing, flat-field support, and ambient temperatures, along with raw digital response, as input data. Experimental measurements are conducted inside a climatic chamber, with the camera imaging a thermoregulated blackbody source. Results demonstrate the calibration effectiveness, achieving precise radiance measurements with a temporal pixel root-mean-square error (RMSE) of 0.09 W/m2/srand residual spatial noise of 0.03 W/m2/sr.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

We discuss the consequences of the unique symmetry of the de Sitter spacetime. This symmetry leads to the specific thermodynamic properties of the de Sitter vacuum, which produces the thermal bath for matter. The de Sitter spacetime is invariant under the modified translations, ${\bf r}\rightarrow {\bf r} -e^{Ht}{\bf a}$, where $H$ is the Hubble parameter. For $H\rightarrow 0$, this symmetry corresponds to the conventional invariance of Minkowski spacetime under translations ${\bf r}\rightarrow {\bf r} -{\bf a}$. Due to this symmetry, all the comoving observers at any point of the de Sitter space perceive the de Sitter environment as the thermal bath with temperature $T=H/\pi$, which is twice larger than the Gibbons-Hawking temperature of the cosmological horizon. This temperature does not violate the de Sitter symmetry, and thus does not require the preferred reference frame, as distinct from thermal state of matter, which violates the de Sitter symmetry. This leads to the heat exchange between gravity and matter, and to instability of de Sitter state towards the creation of matter, its further heating, and finally to the decay of the de Sitter state. The temperature $T=H/\pi$ determines different processes in the de Sitter environment, which are not possible in the Minkowski vacuum, such as the process of ionization of an atom in the de Sitter environment. This temperature also determines the local entropy of the de Sitter vacuum state, and this allows us to calculate the total entropy inside the cosmological horizon. The result reproduces the Gibbons-Hawking area law, which is related to the cosmological horizon, $S_{\rm hor}=4\pi KA$, where $K=1/16\pi G$. This supports the holographic properties of the cosmological event horizon. We extend the consideration of the local thermodynamics of the de Sitter state using the $f({\cal R})$ gravity. In this thermodynamics, the Ricci scalar curvature ${\cal R}$ and the effective gravitational coupling, $K$, are thermodynamically conjugate variables. The holographic connection between the bulk entropy of the Hubble volume, and the surface entropy of the cosmological horizon remains the same, but with the gravitational coupling $K=df/d{\cal R}$. Such connection takes place only in the $3+1$ spacetime, where there is the special symmetry due to which the variables $K$ and ${\cal R}$ have the same dimensionality. We also consider the lessons from the de Sitter symmetry for the thermodynamics of black and white holes.

In the early stage of new vehicle development, the requirements of maximum performance of the air conditioning (AC) system are obtained through Amesim software simulation, but the calibration control of the AC system is usually carried out in the prototype-build vehicle test stage, and the test time is spanned up to 10 months after spring (autumn), summer and winter, of which up to 2 months are for environment chamber tests. Due to the long calibration cycle of AC control in the road test, which seriously affects the vehicle launch time, virtual calibration technology of air conditioning system is developed to shorten the calibration cycle of AC systems and ensure the quality of vehicles. In the project development stage, the calibration control of the vehicle AC system can be realized to carry out the functional test of the AC system in advance. In that, the grade of maturity for the AC system control can be improved, the on-road calibration test cycle can be shortened, and the development cost can be saved.

The pressing threat of global warming poses significant risks to plant survival, adversely affecting their growth and agricultural productivity. It is crucial to understand how plants react to heat stress at the molecular level to develop crops that can withstand higher temperatures. In our study, we investigated the proteome dynamics of *Arabidopsis thaliana* seedlings under moderate heat stress conditions (30°C) using a combination of 15N-stable isotope labeling and the ProteinTurnover algorithm. This approach allowed us to closely examine the proteomic changes across different cellular compartments. Our findings revealed significant changes in the turnover rates of 571 proteins, with an average increase of 1.4-fold, indicating enhanced protein dynamics under heat stress. Notably, root soluble proteins showed more subtle changes, suggesting tissue-specific responses. We also detected significant turnover variations in proteins involved in redox signaling, stress response, and metabolism, highlighting the complex nature of these adaptive mechanisms. In contrast, proteins related to carbohydrate metabolism and mitochondrial ATP synthesis showed little change, underscoring their stability. This detailed analysis illuminates the proteomic adaptations of *Arabidopsis* seedlings to moderate heat stress, enhancing our understanding of plant thermal resilience and supporting efforts to develop thermotolerant crops.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

Laboratory experiments and investigations into natural phenomena in this research series have unveiled the presence of a gravitational repulsion force that permeates our environment on both microscopic and macroscopic scales, contingent upon the thermal energy present. This paper presents a study exploring novel properties of gravitational forces among gas molecules, employing principles of thermodynamics. A model has been devised based on the interactions between pairs of gas molecules. While traditional models treat gravitational interaction as a singular force, our experimental approach validates it as the composite of two distinct forces: gravitational repulsion and attraction. By utilizing established experimental data on gas thermodynamics, our model demonstrates robust performance both analytically and experimentally. It verifies the coexistence of gravitational repulsion and attraction forces among gas molecules, showcases their Inverse-Cube relationship with distance, and elucidates the direct proportionality of the repulsion force to absolute temperature. This bridges a crucial gap between energy and fundamental forces. The order of magnitudes of gravitational repulsion and attraction forces are found to be considerably large, contrasting with the low values predicted by classical theory, which results from their amalgamation. Recognizing these forces as substantial in magnitude promises unprecedented outcomes and advancements.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

High-methoxyl apple pectin (AP) derived from apple was employed as the main ingredient facilitating rheological modification features for developing dysphagia-friendly fluidized alimentary matrices. Xanthan gum (XG) was also included as a composite counterpart to modify the viscoelastic properties of the thickened system under different thermal processes. The results indicate that AP is extremely sensitive to thermal processing, and the viscosity is greatly depleted under a neutral pH level. Moreover, the inclusion of calcium ions echoed a modification effect on the rheological properties of AP, and both the elastic property and viscosity value are promoted after thermal processing. The modification effect of viscoelastic properties (Gʹ and Gʹʹ) is observed while XG is incorporated into the composite formula. By promoting the XG ratio from 7: 3 to 6: 4 (AP: XG), it triggers the rheological transformation from a liquid-like form to a solid-like state, and the viscosity value shows that the AP-XG composite system exhibits better thermal stability after thermal processing. The ambient modifiers of pH (pH &lt; 4) and calcium chloride concentration (7.5%) with an optimal AP-XG ratio of 7:3 lead to weak-gel-like behavior (Gʹʹ &lt; Gʹ), helping to maintain the texture properties of dysphagia-friendly features similar to those prior to the thermal processing.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

There is an international concern for reducing energy consumption and protecting environment by application of circular economy principles in the construction industry. The thermal resistance of concrete plays a significant role in the energy efficiency of a building, and this can be improved by using concrete products with high thermal resistance. This study analyzes the influence of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30% and 100%. The results show that the replacement of sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing walls pannels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, improving the energy performance of buildings, and reducing the environmental impact of construction wastes.

The Surface Urban Heat Island (UHI) is caused by the difference in temperature between the urban and its surrounding areas. However, in the scientific literature, there is no solid methodology defining urban and non-urban areas, which is essential to estimate the SUHI with greater accuracy. This study uses the official national urban areas limit, to obtain the SUHI more accurately on the nine northeastern Brazilian capitals. The land surface temperature was obtained using the Sentinel 3 satellite data for the years 2019 and 2020. Afterward, the maximum and average SUHI, and the complementary indexes were calculated, such as the Urban Thermal Field Variation Index (UTFVI) and the Thermal Discomfort Index (TDI) for the urban areas and their surrounding areas. The Maximum and Average SUHI, obtained values between 1.85 and 8.25 and -4.92 and 2.59 degree difference, respectively, proving the SUHI existence in the study areas. The UTFVI, with values between 0.010 and 0.040, expresses how bad the eco-environmental spaces of urban are. The TDI, with values between 24.61 and 28.89 ºC, expresses the population’s thermal comfort. Therefore, this study provides a better understanding of the surface UHI pioneeringly for the Brazilian Northeast Region.

The thermal conductivity of the products of the interaction of molten core with concrete was derived using number theory. A formula has been found that describes the thermal conductivity of ZrO₂, ZrSiO₄, (U,Zr)SiO₄ and UO₂ over a wide temperature range. Formula is expressed in terms of the atomic numbers of elements, their valencies, the crystal structure of substances, and the thermal conductivities of individual chemical elements of the corium.

A formula for the turbulent Prandtl number is derived in terms of local variables available from two-equations turbulence models. The derivation is a direct consequence of the expected square additivity of the molecular and turbulent parameters defining the effective viscosity and the effective conductivity. The formula does not degenerate and leads to a Kays like formulation if approximated. Its utility and its limitation are discussed.

Minimal rotating thermodynamic systems are addressed. Particle m placed into the rotating symmetrical double-well potential (bowl), providing binary logical system is considered. The condition providing the transfer of the particle from one frictionless half-well to another, and in this way possibility to record 1 bit of information is derived. The procedure of recording turns out to be irreversible; it is impossible to return the particle to its initial state under rotation about the same axis. The same rotating double-well system exerted to the thermal noise is considered. Minimal rotating thermal engine built of the rotating chamber, movable partition and the particle confined within the chamber is treated. Rotation of the system displaces the partition; thus, enabling erasing of one bit information. Erasing of 1 bit of information is due to the inertia (centrifugal force) acting on the partition. Isothermal expansion of the “minimal gas” expectedly gives rise to the Landauer bound. Compression of the “gas” with the rotation around the same axis is impossible and demands the additional axis of rotation. The interrelation between the possibility of recording/erasing information and the symmetry of the system is considered.

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Is it possible to quantify in General Relativity, GR, the entropy generated by supermassive black holes, BHs, during its evaporation time, since the intrinsic Hawking radiation in the infinity that, although insignificant, is important in the effects on the thermal quantum atmosphere?The purpose was to develop a formula that allows us to measure the entropy generated during the evaporation time of different types of BHs of: i. remnant BH of the binary black holes’ merger, BBH: GW150914, GW151226 and LTV151012 detected by the Laser Interferometer Gravitational-Wave Observatory (LIGO), and ii. Schwarzschild, Reissner-Nordström, Kerr and Kerr-Newman, and thus quantify in GR the “insignificant” quantum effects involved, in order to contribute to the validity of the generalized second law (GSL) that directly links the laws of black hole mechanics to the ordinary laws of thermodynamics, as a starting point for unifying quantum effects with GR. This formula could have some relationship with the detection of the shadow’s image of the event horizon of a BH.This formula was developed in dimensional analysis, using the constants of nature and the possible evaporation time of a black hole, to quantify the entropy generated during that time. The energy-stress tensor was calculated with the 4 metrics to obtain the material content and apply the proposed formula.The entropy of the evaporation time of BHs proved to be insignificant, its temperature is barely above absolute zero, however, the calculation of this type of entropy allows us to argue about the importance of the quantum effects of Hawking radiation mentioned by authors who have studied the quantum effects with arguments that are fundamentally based on the presence of the surrounding thermal atmosphere of the black hole.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.

Thermal variations affect tri-trophic interactions involving plants, herbivores, and parasitoids, causing a mismatch between their phenological cycles. In the current environmental context of climate change, climatic factors can undergo profound and sudden changes, such as sudden hot or cold snaps. Here we show that episodes of short but sustained low temperatures have increased, mainly in the month of May, in the last two decades. We subjected galls induced by Asian chestnut gall wasp (ACGW) Dryocosmus kuriphilus to cold stress to assess if and how the pest and its parasitoids were affected. Over the course of two years seasonal parasitism, parasitism rates, the relative abundance of each parasitoid species, and mortality of ACGW were calculated. We found that the cold treatment affected both pest and parasitoids, resulting in a reduction in emerging ACGWs and differing ratios of species within the parasitoid community. The striking example was the change in the relative frequency of three species of Eupelmus spp. and of Mesopolobus tibialis, which doubled in thermally-stressed galls in all chestnut fields. The thermal effects on the development of the host and the direct effects of cold temperatures on the surface of galls (i.e., humidity or hardness of the galls) warrant further research in this direction.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

Equiatomic CuZr alloy undergoes a martensitic transformation from the B2 parent phase to martensitic phases (P21/m and Cm) below 150 °C. We clarified the effect of the thermal cycling on the morphology and crystallography of martensite in equiatomic CuZr alloy using a transmission electron microscopy. The 10th cycled specimens consisted of different multiple structures at the maximum temperature of DSC measurement: 400 °C and 500°C, respectively. At the maximum temperature 400 °C of DSC measurement, it is composed of the fine plate-like variants, and a lamellar eutectoid structure consisting of Cu10Zr7 and CuZr2 phases on the martensitic variant. Concerning the maximum temperature 500 °C of DSC measurement, it is observed the martensitic structure and the lamellar structure in which the martensitic phase was completely eutectoid transformed. The formation of this lamellar eutectoid structure due to thermal cycling leads to the shift of forward and reverse transformation peaks to low and high temperature side. In addition, new forward and reverse transformation peaks indicating a new transformation appeared by thermal cycling, and the peaks remained around -20 °C. This new martensitic transformation behavior is also discussed.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

Coal combustion in thermal power plants releases ash. Ash is reported to cause different adverse health hazards in humans and other organisms. Owing to the presence of radionuclides, it is also considered as a potential radiation hazard. In this study, based on the surface radiation measurements and relevant ancillary data, expected radiation risk zones were identified with regard to the human population residing near the Thermal Power Plant. With population density as the risk determining criteria, about 20% of the study area was at ‘High’ risk and another 20% of the study area was at ‘Low’ risk zone. The remaining 60% was under medium risk zone. Based on the findings remedial measures which may be adopted have been suggested.

In this work we have investigated the role of various additives (emulsifier, anti-dripping agent) and formulation procedure (pre- dispersion of solid additives in polyol via milling) which influence the flame retardancy of 6,6′-[ethan-1,2-diylbis(azandiyl)]bis(6H-dibenzo[c,e][1,2]oxaphosphin-6-oxid) (EDA-DOPO) containing flexible polyurethane foams. For comparison, the flame retardancy of two additional structurally analogues bridged 9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) based compounds i.e. ethanolamine-DOPO (ETA-DOPO) and ethylene glycol-DOPO (EG-DOPO) were also evaluated together with EDA-DOPO in flexible PU foams of various formulations. The flame retardancy of three bridged-DOPO compounds depends on the type of PU formulation. For certain PU formulation containing EDA-DOPO, lower fire performance was observed. Addition of emulsifier and polytetrafluoroethylene (PTFE) to these PU formulations influenced positively the flame retardancy of EDA-DOPO/PU foams. In addition, dispersion of EDA-DOPO and PTFE via milling in polyol improved the flame retardancy of the PU foams. Mechanistic studies performed using pyrolysis combustion flow calorimetry (PCFC) and its coupling to FTIR showed no difference in the combustion efficiency of the bridged-DOPO compounds in PU foams. From these PCFC experiments we can conclude that these bridged-DOPO compounds and their decomposition products may work primarily in the gas phase as flame inhibitors. Physiochemical behavior of additives in PU formulation responsible for the improvement in the flame retardancy of PU foams was further investigated by studying the dripping behavior of the PU foams in UL 94 HB test. A high-speed camera was used to study the dripping behavior in the UL 94 HB test and results indicate a considerable reduction of a total number of melt drips and flaming drips for the flame retardant formulations. This reduction in melt drips and flaming drips during the UL 94 HB tests help PU foams achieve higher fire classification.

This paper reveals the physical properties of Jeffery nanofluid flow past a moving plate embedded in porous medium under the existence of radiation and thermal diffusion. The analysis is carried out in three cases of moving plate, namely stationary plate λ = 0, forth-moving plate λ = 1, back-moving plate λ = −1. Finite difference method is applied to solve the governing equations of the flow and pointed out the variations in velocity, temperature and concentration with the use of graphical presentations. The impact of several parameters on local skin friction, Nusselt number and Sherwood number is also noticed and discussed. Enhancement of velocity is observed under the impact of Jeffery parameter for the cases of stationary plate and back-moving plate, whereas reverse nature is found in the case of forth-moving plate. The velocity enhances as the values of porosity parameter increases for the case of stationary plate and forth-moving plate but a reverse nature is noticed in the case of back-moving plate.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

In the present study, the performance of a 70 L photobioreactor, operating outdoors, was investigated using a purple bacterial strain as Rhodopseudomonas sp. S16-VOGS3 for producing poly-3-hydroxybutyrate (PHB). The novel photobioreactor was equipped with 5L-shaped rows; the bottom of every row was placed in a stainless-steel tank containing water with controlled temperature. The photofermentation trials were carried out under fed-batch mode and under a semi-continuous regimen using lactic acid as carbon source. The effect of the irradiance and the C/N ratio on the PHB accumulation was investigated, in order to evaluate the optimal bacterial growth. The results showed the feasibility of the prototype photobioreactor for the production of PHB by Rhodopseudomonas sp. S16-VOGS3 under the natural light/dark cycle. During the fed-batch growth (144 h long), the cumulative PHB increased quickly reaching the maximum value of 377 mg/L and decreased to 255 mg/L during the semi-continuous regimen (336 h long).

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

The surface thermodynamic properties of polymers and copolymers modified by supramolecular structures are very used in several industrial processes, such as selective adsorption, paints, coatings, colloids, and adhesion applications. Background: Inverse gas chromatography at infinite dilution was proved to be the best technique to determine the surface properties of solid surfaces by studying the adsorption of some model polar and non-polar organic molecules adsorbed on solid surfaces by varying the temperature. Methods: The retention volume of adsorbed solvents is a precious parameter to obtain the London dispersive and polar free energies and the London dispersive surface energy of styrene–divinylbenzene copolymer modified by supramolecular structure of melamine using the Hamieh thermal model and our new methodology consisting in the separation of the two polar and dispersive free energy of interaction. This led to the determination of the polar acid and base surface energy, and the Lewis’s acid-base constants of the various solid materials. Results: all surface energetic properties of styrene–divinylbenzene copolymer modified by melamine at different percentages were determined as a function of temperature, following our new methodology. Conclusions: It was observed that the styrene–divinylbenzene copolymer exhibited the highest London dispersive surface energy which decreased when the melamine percentage increased. All materials presented higher Lewis’s basicity and this Lewis’s basicity increased with the percentage of melamine.

This work aims to evaluate the by-products obtained by thermal and catalytic pyroly-sis of the fraction (organic matter and paper) of municipal solid waste (MSW), in dif-ferent socioeconomic regions, through the yields of reaction products (bio-oil, bio-char, H2O and gas), acid value and chemical composition of bio-oils, and characteriza-tion of biochar, on a laboratory scale. The organic matter and paper segregated from the gravimetric composition of the total waste sample were subjected to drying, crushing and sieving pre-treatment. The experiments were carried out at 450 °C and 1.0 atmosphere, and at 400 °C and 475 °C and 1.0 atmosphere, using 10.0% (by mass) of the basic catalyst Ca(OH)2, in discontinuous mode. The bio-oil was characterized by acidity value and the chemical functions present in the bio-oil identified by FT-IR, NMR and composition by GC-MS. The biochar was characterized by SEM/EDS and XRD. The bio-oil yield increased with the addition of catalyst and the pyrolysis tem-perature. For catalytic pyrolysis, bio-char and gas yields increased slightly with Ca(OH)2 content, while bio-oil and H2O phase remained constant. GC-MS of the liquid reaction products identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil decreased with the addition of the basic catalyst in the process. The concentration of hydrocarbons in the bio-oil appeared with the addition of the catalyst in the catalyt-ic pyrolysis process as catalytic deoxygenation of fatty acid molecules occurs, through decarboxylation/decarbonylation, producing aliphatic and aromatic hydrocarbons, in-troducing the basic catalyst into the thermal process.

Acrostichum aureum is a halophytic pantropical invasive fern growing in mangroves and swamps. Its association with arbuscular mycorrhizal fungi (AMF) has been reported in Asia. AMF and their symbiosis (AM) commonly colonise the absorption organs of terrestrial plants worldwide. Fur-thermore, AMF/AM are well known for their capacity to bioaccumulate toxic elements and to alleviate biotic and abiotic stress (e.g. salinity stress) in their hosts. However, how AMF are in-volved in the halophytism of A. aureum, and the structures where NaCl accumulates remains unknown. This study shows that A. aureum forms AM in Neotropical thermal margins of natural ponds, NaCl accumulation occurs inside AMF vesicles, and CaSO4 precipitates in colonised roots. Therefore, AM would be contributing to the halophytic nature of this fern, allowing it to thrive in saline and thermal environments by capturing NaCl from fern tissues, compartmentalizing it inside its vesicles and precipitating CaSO4.

The Ultra-Cold Neutron (UCN) source being commissioned at North Carolina State Universityâs PULSTAR reactor is uniquely optimized for UCN production in the former graphite-filled thermal column outside of the reactor pool. The source utilizes a remote moderation design which is particularly well suited to the PULSTAR reactor on account of its large thermal and epithermal neutron leakage from the core face. This large non-equilibrium flux from the core is efficiently transported to the UCN source through the specially designed beam port in order to optimize UCN production at any given reactor power. The increased distance to the source from the core also greatly limits the heat load on the cryogenic system. A MCNP model of this system was developed and is in good agreement with gold foil activation measurements using a mock-up setup as well as with the real UCN source heavy water moderator. These results established a firm baseline for estimates of the cold neutron flux available for UCN production and prove that remote moderation in a thermal column port is a valuable option for future designs of cryogenic UCN sources.

Recent advancements highlight the utilization of vegetable oils as additives in polymeric materials, particularly for replacing conventional plasticizers. Buriti oil (BO), extracted from the Amazon's Mauritia flexuosa palm tree fruit, boasts an impressive profile of vitamins, minerals, proteins, carotenoids, and tocopherol. This study investigates the impact of incorporating buriti oil as a plasticizer in linear low-density polyethylene (LLDPE) matrices. The aim of this research was to evaluate how buriti oil, a bioactive compound, influences the thermal and rheological properties of LLDPE. Compositions of buriti oil\LLDPE were prepared via melt intercalation techniques, and the resulting materials were characterized through Thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), mechanical property testing, and contact angle measurement. The addition of buriti oil was found to act as a processing aid and plasticizer, enhancing the fluidity of LLDPE polymer chains. TGA revealed distinct thermal stabilities for buriti oil/LLDPE under different degradation conditions Notably, buriti oil exhibited an initial weight loss temperature at 402°C, whereas LLDPE at 466.4°C. This indicated a minor reduction in the thermal stability of buriti oil/LLDPE compositions. The thermal stability, as observed through DSC displayed a nuanced response to the oil's incorporation, suggesting a complex interaction between the oil and polymer matrix. Detailed mechanical testing indicated a marked increase in tensile strength and elongation at break, especially at optimal concentrations of buriti oil. SEM analysis showcased a more uniform and less brittle microstructure, correlating with the enhanced mechanical properties. Contact angle measurements revealed a notable shift in surface hydrophobicity, indicating a change in the surface chemistry. This study demonstrates that buriti oil can positively influence the processability and thermal properties of LLDPE contributing to expand its potential applications as an effective plasticizer.

The increasing adoption of distributed recycling via additive manufacturing (DRAM) has facilitated the revalorization of materials derived from waste streams for additive manufacturing. Recycled materials frequently contain impurities and mixed polymers, which can degrade their properties over multiple cycles. This degradation, particularly in rheological properties, limits their applicability in 3D printing. Consequently, there is a critical need for a tool that enables rapid assessment of the flowability of these recycled materials. This study presents the design, development, and manufacturing of an open-source melt flow index (MFI) apparatus. The proposed MFI tool offers a user-friendly and cost-effective solution for evaluating the flow properties of materials from waste streams, thereby enhancing their viability for additive manufacturing applications.

Previous reviews by the authors [1, 2] indicate the continuing development and improvement of thermal protective systems through the introduction of polymer nanocomposites into polymer matrix composites. These materials perform as thermal protective systems for a variety of aerospace applications, such as thermal protection systems (TPS), solid rocket motors (SRM) nozzles, internal insulation of SRM, leading edges of hypersonic vehicles, and missile launch structures. A summary of the most recent, global technical research is presented. Polymeric resin systems continue to emphasize phenolic resins and other materials. New high-temperature organic resins based on phthalonitrile (PN), and polysiloxane are described and extend the increased temperature range of resin matrix systems.

After an introductory reminder of safety concerns pertaining to early rechargeable battery technologies, this review discusses current understandings and challenges of sodium-ion batteries. Sodium-ion technology is now being marketed by industrial promoters who are advocating its workable capacity, use of readily accessible and cheaper key cell components. Often claimed to be safer than lithium-ion cells, currently only limited scientific-sound safety assessment of sodium-ion cells has been performed. However, the predicted sodium-ion development roadmap reveals that significant variants of sodium-ion batteries will potentially enter the market in the near future. With recent experiences of lithium-ion battery failures, sodium-ion battery safety management will constitute a key aspect of successful market penetration. As such this review discusses the safety issues of sodium-ion batteries presenting a twofold innovative perspective: i) in terms of comparison with the parent lithium-ion technology making use of the same working principle and similar flammable non-aqueous solvent basis and ii) anticipating the arrival of innovative sub-chemistries at least partially inspired from successive generations of lithium-ion cells. The authors do hope that the analysis provided will assist the concerned stakeholders in the quest for safe marketing of sodium-ion batteries.

Despite the best efforts in air-purification, airborne infectious diseases do and will continue to spread due to continuous emission of bioaerosols by the host/infected person. To tackle the rapid spread of airborne infectious diseases, a shift in focus from air-purification to bioaerosol disinfection/ decontamination is urgently needed. In this work, we studied a cold plasma ionizer (CPI) and electrostatic precipitator (ESP)-coupled CPI (CPI-ESP) for disinfection and cleaning of bioaerosols. Using porcine respiratory coronavirus (PRCV) and E. coli in a testing chamber, we demonstrated that CPI coupled with ESP is an effective technology for inactivating aerosolized microorganisms and microorganisms spread on surfaces. In addition, we have demonstrated the efficiency of a CPI-ESP coupled device for disinfection of naturally occurring airborne microbials in a few indoor settings (i.e., an living room, a discussion room, a schoolroom and an office) to determine the treatment duration- and human activity-dependent efficacy. To understand the disinfection mechanism, we conduced fluorescence microscopy study to reveal different degree of bacteria cell membrane damage under CPI treatment.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

Metal-organic frameworks (MOFs) have been subject of extensive scientific investigation in the last three decades and, currently, are one of the type of compounds most studied to be potentially applied in a wide range of distinct catalytic processes. Pristine MOF compounds provide several intriguing benefits for catalytic applications, including high interior surface areas and densities of active sites, allowing high catalytic reaction rates per volume, post-synthesis modified with com-plementary catalytic groups, enabling multiple functional groups to catalyze the reaction. Most of large-scale catalytic applications, including those in fuel processing, gas emission reduction and chemical synthesis, nevertheless the pristine MOFs often reveal limited stabilities and opportuni-ties for regeneration at high temperatures. As a result, the real applications of MOFs in these tech-nologies are likely to be constrained, and their controlled thermal modification aiming the prepa-ration of MOF-derivative compounds has been applied to induce crystalline structural changes and increase their structural stability, enhancing its potential applicability in more severe catalytic processes. Recent advances concerning the use of this strategy to boost the catalytic potential of the MOF-derivative compounds are outlined in this short-review article.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.