Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

Tree nuts confer many health benefits because of their high content of vitamins and antioxidants and they are increasingly consumed in the last the years. Food processing is an important industrial tool to modify allergenic properties of foods, in addition to ensure safety and to enhance organoleptic characteristics. The effect of high pressure, without and with heating, on SDS-PAGE and immunodetection profile of potential allergenic proteins (anti-11S, anti-2S and anti-LTP) of pistachio, cashew, peanut, hazelnut, almond and chestnut was investigated. Processing based on heat and /or pressure and Ultra high pressure (HHP, 300-600 MPa) without heating was applied. After treating the six tree nuts with pressure combined with heat a progressive diminution of proteins with potential allergenic properties was observed. Moreover, some tree nuts proteins (pistachio, cashew and peanut) seemed to be more resistant to technological processing than others (hazelnut and chestnut). Differences among tree nut varieties were found regarding to protein content, SDS and immunoblotting profile. High pressure combined with heating processing markedly reduce tree nut allergenic potential as the pressure and treatment time increases. HHP do not alter hazelnut and almond immunoreactivity

This study explored the effects of a comprehensive health care program (CHCP) on blood pressure, blood glucose, body composition, and depression in older adults living alone. We used a quasi-experimental, two-group, pre-posttest design. The CHCP consisted of open lectures, health counseling, exercise classes, nutrition counseling, and self-help group meetings at a local senior welfare center. Fifty-eight subjects participated in this study, with thirty subjects in the experimental group and twenty-eight subjects in the control group. Data were analyzed using the descriptive statistics, χ²-test, and t-test. Comparisons of the pretest and posttest systolic blood pressure (t = - 2.530, p < .016) and blood glucose (t = 3.089, p < .004) between the experimental and control groups showed significant differences. In both the experimental (t = 3.949, p < .001) and control groups (t = 3.816, p < .002), depression symptoms showed a significant decrease post-test, compared with pre-test. Our findings infer that older adults require physical and psychosocial healthcare and that more efforts must be made to improve the general health and wellbeing of this population group.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

The synthesis of magnetic nanoparticles (MNPs) coated with hydrophilic poly-sodium-acrylate ligands (PSA) was studied to assess PSA-MNP complexes as draw solution (DS) solutes in forward osmosis (FO). For MNP-based DS, the surface modification and the size of the MNPs are two crucial factors to achieve a high osmolality. Superparamagnetic nanoparticles (NP) with functional groups attached may represent the ideal DS where chemical modifications of the NPs can be used in optimizing the DS osmolality and the magnetic properties allows for efficient recovery (DS re-concentration) using an external magnetic field. In this study MNPs with diameters of 4 nm have been prepared by controlled chemical co-precipitation of magnetite phase from aqueous solutions containing suitable salts of Fe2+ and Fe3+ under inert atmosphere and a pure magnetite phase could be verified by X-ray diffraction. Magnetic colloid suspensions containing PSA coated MNPs with three different molar ratios of PSA : MNP = 1:1, 1:2 and 1:3 were prepared and assessed in terms of osmotic pressure, aggregation propensity and magnetization. FTIR confirmed the presence of PSA on coated MNPs and pristine PSA-MNPs with a molar ratio PSA : MNP = 1:1 exhibited an osmotic pressure of 30 bar. Molar ratios of PSA : MNP = 1:2 and 1:3 lead to formation of less stabile magnetic colloid solutions which led to formation of aggregates with larger average hydrodynamic sizes and modest osmotic pressures (5.5 bar and 0.2 bar respectively). After purification with ultrafiltration, the 1:1 nanoparticles exhibited an osmotic pressure of 9 bar with no aggregation and a sufficient magnetization of 25 emu/g to allow for DS regeneration using an external magnetic field. However, it was observed that the amount of PSA molecules attached to the MNPs decreased during DS recycling steps leaving only strong chelate bonded core-shell PSA as coating on the MNPs. This demonstrates the crucial role of MNP coating robustness in designing an efficient MNP-based DS for FO.

Intelligent algorithms are recently used in the optimization process in chemical engineering and application of multiphase flows such as bubbling flow. This overview of modeling can be a great replacement with complex numerical methods or very time-consuming and disruptive measurement experimental process. In this study, we develop the adaptive network-based fuzzy inference system (ANFIS) method for mapping inputs and outputs together and understand the behavior of the fluid flow from other output parameters of the bubble column reactor. Neural cells can fully learn the process in their memory and after the training stage, the fuzzy structure predicts the multiphase flow data. Four inputs such as x coordinate, y coordinate, z coordinate, and air superficial velocity and one output such as pressure gradient are considered in the learning process of the ANFIS method. During the learning process, the different number of the membership function, type of membership functions and the number of inputs are examined to achieve the intelligent algorithm with high accuracy. The results show that as the number of inputs increases the accuracy of the ANFIS method rises up to almost for all cases, while the increment in the number of rules has a effect on the intelligence of artificial algorithm. This finding shows that the density of neural objects or higher input parameters enables the moded for better understanding. We also proposed a new evaluation of data in the bubble column reactor by mapping inputs and outputs and shuffle all parameters together to understand the behaviour of the multiphase flow as a function of either inputs or outputs. This new process of mapping inputs and outputs data provides a framework to fully understand the flow in the fluid domain in a short time of fuzzy structure calculation.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

The aim of this work is to present a design approach of a Shock-Induced Combustion Ramjet (Shcramjet) inlet, and present its optimization in terms of the flow and geometrical parameters. The flow properties of mixed compression type inlet of a Shcramjet are examined using analytical and numerical techniques. The geometries obtained with variations in the wedge angles, length, height and cowl lip positions are used to study the flow characteristics of inlet, identifying bow shock temperature ratio as the optimization parameter. The two-dimensional geometries of two-shock and three-shock inlet models designed analytically for shock-on-lip condition at Mach 12.5 and an altitude of 32.5 km are numerically simulated in OpenFOAM CFD Toolbox. A density based compressible CFD solver based on central upwind schemes of Kurganov and Tadmore is used to solve 2D inviscid Euler equations. The inlet total pressure recovery is expressed as a function of temperature ratios of compression shocks, and is found to have a maxima at a bow shock temperature ratio at the design condition when the bow and external shocks have equal strengths. The effect of considering the flow to be calorically imperfect is studied numerically, and the deviation from the analytical design is presented.

Distant Retrograde Orbits in the Earth-Moon system are gaining in popularity as stable `parking' orbits for various conceptual missions. To investigate the stability of potential Distant Retrograde Orbits, simulations were executed, with propagation running over a thirty-year period. Initial conditions for the vehicle state were limited such that the position and velocity vectors were in the Earth-Moon orbital plane, with the velocity oriented such that it would produce retrograde motion about Moon. The resulting trajectories were investigated for stability against the eccentric relative orbits of Earth and Moon in an environment that also included gravitational perturbations from Sun, Jupiter, and Venus, and the effects of radiation pressure. The results appear to indicate that stability is enhanced for certain resonant states within the Earth-Moon system.

Knee osteoarthritis is a prevalent joint disease affecting millions of individuals globally. While total knee arthroplasty is an effective treatment for advanced stages of KOA, it may not be suitable for earlier stages or younger patients. Supervised exercise therapy has proven to be the first line treatment of preference in tackling pain and disability caused by KOA. However, the high intensities required to induce positive muscle adaptations are not indicated in this population as this is often accompanied by pain, discomfort, and frustration; leaving low load resistance training as the only feasible method of treatment. Recently, the use of blood flow restriction training began to emerge as a substitute for high load resistance training. With BFRT, a cuff is applied around the proximal aspect of the affected limb, causing partial arterial and full venous occlusion, thereby inducing localized hypoxia and accumulation of metabolites, mimicking the effects of high load resistance training, albeit with low loads. Consequently, BFRT might offer a suitable and more effective alternative for KOA patients who are not (yet) eligible for TKA, compared to the traditional exercise therapy. This review aims to summarize the current evidence as regards the application of Blood Flow Restriction in exercise therapy of knee osteoarthritis patients, with particular consideration of the underlying mechanisms and its safety, as well as general guidelines for practical implementation into clinical practice. In doing so, this narrative review aims to create a framework allowing the translation from theory to practice.

Fluidized beds are pivotal in the process industry and chemical engineering, with Computational Fluid Dynamics (CFD) playing a crucial role in their design and optimization. Challenges in CFD modeling stem from the scarcity or inconsistency of experimental data for validation, along with the uncertainties introduced by numerous parameters and assumptions across different CFD codes. This study navigates these complexities by comparing simulation results from the open-source MFIX and OpenFOAM, and the commercial ANSYS FLUENT, against experimental data. Utilizing a Eulerian-Eulerian framework and the kinetic theory of granular flow (KTGF), the investigation focuses on solid-phase properties through the classical drag laws of Gidaspow and Syamlal-O’Brien across varied parameters. Findings indicate that ANSYS Fluent, MFiX, and OpenFOAM can achieve reasonable agreement with experimental benchmarks, each showcasing distinct strengths and weaknesses. The study also emphasizes that both the Syamlal-O’Brien and Gidaspow drag models exhibit reasonable agreement with experimental benchmarks across the examined CFD codes, suggesting a moderated sensitivity to the choice of drag model. Moreover, the analysis were also carried out for 2D and 3D simulations, revealing that the dimensional approach impacts the predictive accuracy to a certain extent, with both models adapting well to the complexities of each simulation environment. The study highlights the significant influence of restitution coefficients on bed expansion due to their effect on particle-particle collisions, with a value of 0.9 deemed optimal for balancing simulation accuracy and computational efficiency. Conversely, the specularity coefficient, impacting particle-wall interactions, exhibits a more subtle effect on bed dynamics. This finding emphasizes the critical role of carefully choosing these coefficients to effectively simulate the nuanced behaviors of fluidized beds.

This work examines the beneficial role of an unsteady stenosis, operating without the use of any external energy source, as a means for augmenting the flow rate of a valveless pump in a hydraulic loop, including an open tank. In contrast to our previous work that the loop was horizontal, here gravity was taken into account. The stenosis neck cross-sectional area was controlled by the fluid pressure and an opposing force applied externally by a spring of adjustable tension. The pincher compressed and decompressed periodically a part of a flexible tube with frequencies from 5 Hz to 11 Hz and compression ratios Ab from 24% to 65%. The presence of the stenosis increased the net flow rate 19 times for Ab = 24%, and 6.3 times for Ab = 38%, whereas for Ab = 65%, the flow rates were comparable. The volumetric efficiency varied from 30% to 40% under the presence of the stenosis, and from 2% to 20% without the stenosis. The role of the stenosis role was to cause a unidirectional flow, opening during tube compression and closing during decompression. The pressure amplitudes along the flexible tube increased towards the rigid-flexible tube junction (as a result of the wave reflections) which were found to be significantly attenuated by the presence of the stenosis.

Parallax processing and structure preservation has long been important and challenging tasks in image stitching. In this paper, an image stitching method based on sliding camera to eliminate perspective deformation and asymmetric optical flow to solve parallax is proposed. By maintaining the viewpoint of two input images in the mosaic non-overlapping area and creating a virtual camera by interpolation in the overlapping area, the viewpoint is gradually transformed from one to another image view-point so as to complete the smooth transition of the two image viewpoints and reduce perspective deformation. Two coarsely aligned warped images are generated with the help of a global projection plane. After that, the optical flow propagation and gradient descent method are used to quickly calculate the bidirectional asymmetric optical flow between the two warped images, and the optical flow-based method is used to further align the two warped images to reduce parallax. In the image blending, the softmax function and registration error are used to adjust the width of the blending area, further eliminating ghosting and reduce parallax. Finally, the comparative experiments show that our method can effectively eliminate perspective deformation, reduce misalignment, and save running time.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

The main purpose of this study was to design a workplace in the conditions of a digital factory. The goal of this study is to compile a proposal for improving the layout solution in the selected enterprise to reduce material flows between individual workplaces. In addition, the workplace research study uses methods of material flow analysis with the application of visTABLE software support, which serves as a tool for designing production processes. The main result of the study was the reduction of the production time of the beam by 10 minutes and the creation of proposals for solutions for the company. The study helped with the visualization of processes within the digital factory to simplify and clarify processes at the workplace.

Overexpression of human epidermal growth factor receptor 2 (HER2) in breast and gastric cancers is an important target for monoclonal antibody (mAb) therapy. All therapeutic mAbs, including anti-HER2 mAbs, exhibit adverse effects probably due to the recognition of antigens expressed in normal cells. Therefore, tumor-selective or specific mAbs can be beneficial in reducing the adverse effects. In this study, we established a novel cancer-specific anti-HER2 antibody, named H₂Mab-250/H₂CasMab-2 (IgG₁, kappa). H₂Mab-250 reacted with HER2-positive breast cancer BT-474 and SK-BR-3 cells. Importantly, H₂Mab-250 did not react with non-transformed normal epithelial cells (HaCaT and MCF 10A) and immortalized normal epithelial cells in flow cytometry. In contrast, most anti-HER2 mAbs including H₂Mab-119 (IgG₁, kappa) reacted with both cancer and normal epithelial cells. Furthermore, a core-fucose deleted IgG_2a-type H₂Mab-250 (H₂Mab-250-mG_2a-f) could trigger the antibody-dependent cellular cytotoxicity activity to BT-474, but not to HaCaT cells. Furthermore, H₂Mab-250-mG_2a-f exhibited an in vivo antitumor effect against BT-474 xenograft. Immunohistochemical analysis demonstrated that H₂Mab-250 possesses much higher reactivity to the HER2-positive breast cancer tissues compared to H₂Mab-119, and did not react with normal tissues, including heart, breast, stomach, lung, colon, kidney, and esophagus. The epitope mapping demonstrated that the Trp614 of HER2 domain IV mainly contributes to the recognition by H₂Mab-250. H₂Mab-250 could contribute to the development of chimeric antigen receptor-T or antibody-drug conjugates without adverse effects for breast cancer therapy.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

Introduction: The coronary flow reserve (CFR) is a sign of early-stage coronary artery disease (CAD). Plasma atherogenic index (PAI) is related to atherosclerosis and cardiovascular mortality. Therefore, our aim was to determine CFR and PAI in patients with primary hyperparathyroidism (PHPT) and investigate whether PAI can be used in the detection of early-stage CAD. Material and Methods: The sample was comprised of 44 patients with PTHT and 33 healthy volunteers. We defined CFR as the ratio of the hyperemic diastolic peak velocity to the baseline diastolic peak velocity. PAI values were calculated with the formula of log 10 triglyceride (TRG) / high-density lipoprotein (HDL). Result: The comparison of the groups for PAI and CFR demonstrated that PAI levels were significantly higher while CFR levels were significantly lower in the PTHT patients (p<0.01, p=0.01, respectively). The correlation analysis revealed that CFR was negatively correlated with PAI and TRG (PAI- p<0.0001 r=-0.537).The multivariate logistic regression analysis showed that only a high PAI level (OR: 151.6, 95% confidence interval (CI): 4.1-5480, p=0.006) was an independent predictor of reduction in CFR in PHPT patients. Conclusion: Overall, we found an independent correlation between PAI and CFR values. Hence, PAI may be useful in identifying PHPT patients facing a high risk of adverse cardiovascular events and may also allow early diagnosis of subclinical atherosclerosis.

Microstructured optical fibres (MOFs) are a new type of optical fibres that possess a wide range of optical properties and many advantages over common optical fibres. Those are provided by unique structures defined by a pattern of periodic or quasi-periodic arrangement of air holes that run through the fibre length. In recent years, MOFs have opened up new possibilities in the field of optics and photonics, enabling the development of advanced devices and novel optical systems for different applications. The key application areas of PCFs vary from telecommunications and high-power energy transmission to quantum optics and sensing. The stack-and-draw method is a standard manufacturing technique for MOFs, where a preform is first manually created and then drawn in a high-tech furnace into a fibre with the required final dimensions and position of the air holes. Since in the manufacturing process experimenters can control only a few parameters, mathematical models and numerical simulations of the drawing process are highly requested. They not only allow to deepen the understanding of physical phenomena occurring during the drawing process, but they also accurately predict the final cross-section shape and size of the fibre. In this manuscript, we assume thermal equilibrium between the furnace and the fibre and propose a functional form of the fibre temperature distribution. We utilise it with asymptotic mass, momentum, and evolution equations for free surfaces already available in the literature to describe the process of fibre drawing. By doing so, the complex heat exchange problem between the fibre and the furnace need not be solved. The numerical results of the whole asymptotic model overall agree well with experimental data available in the literature, both for the case of annular capillaries and for the case of holey fibres.

Recanalization poses challenge in coil embolization for cerebral aneurysms. Establishing predictive models for post-embolization recanalization is important for clinical decision-making. However, conventional statistical and machine learning (ML) models may overlook critical parameters during the initial selection process. In this study, we automated the identification of significant hemodynamic parameters using a PointNet-based deep neural network (DNN), leveraging their inherent 3D features. Further feature analysis was conducted utilizing saliency mapping, an explainable artificial intelligence (XAI) technique. The study encompassed the analysis of velocity, pressure, and wall shear stress (WSS) in both pre- and post-coiling models derived from computational fluid dynamic (CFD) simulations for 59 aneurysms. Velocity was identified as the most pivotal parameter, supported by the lowest P-value from statistical analysis and the highest area under the curves (AUROC)/precision-recall curves (AUPRC) values from DNN model. Moreover, visual XAI analysis revealed robust injection flow zones with notable impingement points in pre-coiling models, as well as pronounced interplay between flow dynamics and the coiling plane were important 3D features in identifying the recanalized aneurysms. The combination of DNN and XAI was found to be an accurate and explainable approach not only at predicting post-embolization recanalization but also at discovering unknown features in the future.

In the current study, a two-dimensional numerical study is carried out to investigate the performance of a novel Double-chamber Parallel Flexible Valves micropump, which utilized the electrowetting-on-dielectrics (EWOD) effect to drive the microfluid flow. By observing the flow fields, the internal circulations are seen on both the left and right side of the pump. The generation of the backflow is discussed by tracking the movement of the vortices. Only slight flow fluctuation is seen in the micropump. Based on the simulation outcomes, the structural parameters including the width of the inlet/outlet, the width of the pumping channel and the diverging angle in the micropump are analyzed, the influence of these parameters on the pumping volume and the maximum pressure have been discussed. Eventually, a group of optimal parameter combinations is given according to the results to extend the operating potential of the micropump.

Temporal downscaling of gridded geophysical data is essential for improving climate models, weather forecasting, and environmental assessments. However, existing methods often could not accurately capture multi-scale temporal features, affecting their accuracy and reliability. To address this issue, we introduce an Enhanced Residual U-Net architecture for temporal downscaling. The architecture, which incorporates residual blocks, allows for deeper network structures without the risk of overfitting or vanishing gradients, thus capturing more complex temporal dependencies. The U-Net design inherently could capture multi-scale features, making it ideal for simulating various temporal dynamics. Moreover, we implement a flow regularization technique with advection loss to ensure that the model adheres to physical laws governing geophysical fields. Our experimental results across various variables within the ERA5 dataset demonstrate an improvement in downscaling accuracy, outperforming other methods.

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

The flow around thick airfoils at low Reynolds numbers and the possibility of using energy methods to control flowfield, increase lift and reduce drag are considered. For calculations, a series of propulsion airfoils is used, obtained by a combination of solving the inverse problem of aerodynamics and stochastic methods of global optimization. The calculations take into account the transition from the laminar flow regime to the turbulent one, which has a significant effect on the lift and airfoil drag. The applicability of various turbulence models for airfoil modelling at low Reynolds numbers is discussed. The results of numerical simulation make it possible to determine the dependence of the lift coefficient on the angle of attack and the optimal flow rate of air taken from the airfoil surface for each angle of attack. The results of numerical simulation are compared with the data of a physical experiment, and conclusions are drawn about the accuracy of various turbulence models.

The determination of critical ventilation flow rate is significant for the risk control and the standard development during accidental hydrogen leakage in a confined space with hydrogen-related equipment. In this paper, an analytical model for calculating critical ventilation flow rate was proposed through the quantification and constraint solution of ventilation effect and ventilation cost. The experimental method was used to investigate the effects of nozzle diameter and stagnation pressure on diffusion and ventilation for horizontal hydrogen leakage in a cuboid chamber. Ventilations from 30m3/h to 180m3/h were carried out through the rectangular vent. It was shown that the peak concentration of the measuring point is positively correlated with the stagnation pressure and the nozzle diameter. The experimental data are used to verify the analytical model by calculating the effective ventilation time. The study demonstrates that the critical ventilation flow rate can be increased significantly at higher stagnation pressures and larger nozzle diameters. And the discrepancy of critical ventilation flow rates under different nozzle diameters will be enhanced with the increase of stagnation pressure. For the stagnation pressure of 0.4MPa, the critical ventilation flow rate under 4mm nozzle even increases by 52% relative to the 2mm nozzle.

The flow field around a straight chain of multiple slip spherical particles rotating steadily in an incompressible Newtonian fluid about their line of centers is analyzed at low Reynolds numbers. The particles may vary in radius, slip coefficient, and angular velocity, and they are permitted to be unevenly spaced. Through the use of a boundary collocation method, the Stokes equation governing the fluid flow is solved semi-analytically. The interaction effects among the particles are found to be noteworthy under appropriate conditions. For the rotation of two spheres, our collocation results for their hydrodynamic torques are in good agreement with the analytical asymptotic solution in the literature obtained by using a method of twin multipole expansions. For the rotation of three spheres, the particle interaction effect indicates that the existence of the third particle can influence the torques exerted on the other two particles noticeably. The interaction effect is stronger on the smaller or less slippery particles than on the larger or more slippery ones. Torque results for the rotation of chains of many particles visibly show the shielding effect among the particles.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

Estimating peak flow for a catchment is commonly undertaken using the design event method, however this method does not allow for the understanding of uncertainty in the result. This research first presents a simplified method of fragments approach to rainfall disaggregation that ignores the need to consider seasonality, offering a greater diversity in storm patterns within the resulting sub-daily rainfall. By simulating 20 iterations of the disaggregated sub-daily rainfall within a calibrated continuous simulation hydrologic model, we were able to produce multiple long series of stream flow at the outlet of the catchment. With this data, we investigated the use of both the annual maximum and peaks over threshold approaches to flood frequency analysis and found that for a one in 100 year annual exceedance probability peak flow, the peaks over threshold method (333m3/s ±50m3/s) was significantly less uncertain than the annual maximum method (427m3/s ±100m3/s). For the one in 100 year annual exceedance probability, the median peak flow from the peaks over threshold method (333m3/s) produced an outcome comparable to the design event method peak flow (328m3/s), indicating that this research offers an alternative approach to estimating peak flow, with the additional benefit of understanding the uncertainty in the estimation. Finally, the paper highlighted the impact that length and period of streamflow has on peak flow estimation and noted that previous assumptions around the minimum length of gauged streamflow required for flood frequency analysis may not be appropriate in particular catchments.

Living beings are composite thermodynamic systems in non-equilibrium conditions. Within this context, there are a number of thermodynamic potential differences (forces) between them and the surroundings, as well as internally. These forces lead to flows, which, ultimately, are essential to life itself. Living beings are under the pressures of natural selection, thus are biological flows as well. At the same time, the maintenance of homeostatic conditions, the tenet of physiology, demands regulation of these flows by control of variables. However, due to the very nature of these systems, regulation of flows and control of variables become entangled in closed loops. Therefore, the search for adaptation in flows takes a different path than the search for adaptation in morphological traits. Being at the roots of transfer processes, thermodynamic criteria turn out to be as natural physical candidates. Likewise, being at the roots of physiology, control turns out to be as a natural biological candidate in that path. Here we show how to combine entropy generation, with respect to a generalized process, and control of parameters (in such a generalized process) in order to create a criterium of optimal ways to regulate changes in generalized flows.

Polymeric microparticles of polyethyleneglycol-polylactic acid-co-glycolic acid (PEG-PLGA) are widely used as drug carriers for a variety of applications due to their unique characteristics. Herein, we developed a novel method for the synthesis of uniformly sized microparticles via coaxial flow-phase separation. The study evaluated the effect of various process parameters on microparticle size and polydispersity including polymer concentration, stirring rate, surfactant concentration, and the organic/aqueous phase flow rate and volume ratio. The results demonstrated that stirring rate and polymer concentration had the most significant impact on the mean particle size and distribution whereas surfactant concentration had the most substantial impact on the morphology of particles. Several microparticle formulations yielding particle sizes in the range of (5-50 µm), morphology, and concentration were synthesized as a demonstration of the tunability and scalability of this method. Notably, by controlling the process parameters microparticles of less than ~ 7 μm could be made using polymer concentrations varying by an order of magnitude. Finally, we demonstrated the tunability and scalability of this method by showing a 10-fold increase in encapsulation efficiency, a 3-fold increase in drug loading of a model hydrophilic drug, and modified release kinetics in microparticle formulations of comparable sizes but different polymer concentrations.

The paper presents the results of modeling the problem of injecting liquid sulfur dioxide into a porous reservoir initially saturated with methane and ice. The model presented in the paper assumes the formation of three different regions, namely, the near one, saturated with liquid SO2 and its hydrate; the far one, containing methane and ice, and the intermediate one, saturated with methane and water. The effects of various parameters of the porous medium and injected SO2 on the nature of the course of the hydrate formation process have been studied. It is shown that with a decrease in reservoir permeability or injection pressure, the length of the intermediate region decreases, which in the limiting case means the formation of SO2 hydrate in the mode without the formation of an extended region saturated with methane and water. It is shown that such a regime is also typical for the case of high initial injection pressures, as well as low values of the initial reservoir temperature and injection temperature.

Data-Flow and Higher-Order Mutation are white-box testing techniques. To our knowledge, no work has been proposed to compare data flow and higher-order mutation. This paper compares all def-uses data-flow and second-order mutation criteria. This compassion investigates the subsumption relation between these two criteria and evaluates the effectiveness of test data developed for each. To compare the two criteria, a set of test data satisfying each criterion is generated, which is used to explore whether one criterion subsumes the other criterion and assess the effectiveness of the test set that was developed for one methodology in terms of the other. The results showed that the mean mutation coverage ratio of the all du-pairs adequate test cover is 80.9%, and the mean data flow coverage ratio of the 2nd-order mutant adequate test cover is 98.7%. Consequently, 2nd-order mutation “ProbSubsumes” the all du-pairs data flow. The failure detection efficiency of the mutation (98%) is significantly better than the failure detection efficiency of data flow (86%). Consequently, 2nd-order mutation testing is “ProbBetter” than all du-pairs data flow testing. In contrast, the size of the test suite of 2nd-order mutation is more significant than the size of the test suite of all du-pairs.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

We propose an algorithm for generating a panoramic image of a pipe’s inner surface based on inverse perspective mapping (IPM). For efficient crack detection, we used only perspective images of the pipe interior that can be obtained with a single lens camera instead of those taken with a 360-degree camera or a 3D depth camera. Frontal images taken while passing through the pipe were converted to images of the inner surface of the pipe using IPM. We derived a generalized IPM formula that considers the slope of the image plane to correct image distortion caused by the tilt of the plane; this IPM formula was derived based on the vanishing point of the perspective image, which was detected using optical flow techniques. Finally, the multiple transformed images with overlapping areas were combined via image stitching to create a panoramic image of the inner pipe surface. To validate our proposed algorithm, we restored images of pipe inner surface using a 3D pipe model and used these images for crack detection.

Acute pancreatitis (AP) is the most common gastrointestinal disease leading to hospitalizations. The development of AP leads to damage of the pancreatic microcirculation with a cascade of subsequent events resulting, among others, in coagulopathy. Previous research showed that anticoagulants can be an important therapeutic agent. Heparin and acenocoumarol can alleviate the course of AP, as well as accelerate healing and post-inflammatory regeneration of the pancreas. The aim of this study was to check whether warfarin, a drug with more stable effects than acenocoumarol, affects the healing and regeneration of the pancreas in the cerulein-induced AP. AP was evoked in Wistar male rats by intraperitoneal administration of cerulein. The first dose of warfarin (45, 90 or 180 µg/kg/dose) was administered 24 hours after the first dose of cerulein and the doses of warfarin were repeated once a day in subsequent 10 days. The severity of acute pancreatitis was assessed immediately after the last dose of cerulein, as well as 1, 2, 3, 5, and 10 days after AP induction. Treatment with warfarin dose-dependently increased interna-tional normalized ratio (INR) and attenuated the severity of pancreatitis in histological ex-amination and accelerated pancreatic recovery. Those effects were accompanied with a faster reduction in the pancreatitis-evoked increase in serum activity of amylase and lipase, serum concentration of pro-inflammatory interleukin-1β, and plasma level of D-Dimer. In addition, treatment with warfarin decreased pancreatic weight and improved pancreatic blood flow in rats with AP. The therapeutic effect was particularly pronounced after the administration of warfarin at a dose of 90 µg/kg/dose. Conclusion: Administration of warfarin accelerates re-generation of the pancreas and recovery in the course of cerulein-induced mild-edematous acute pancreatitis.

Cluster of differentiation 44 (CD44) promotes tumor progression through the recruitment of growth factors, and the acquisition of stemness, invasiveness, and drug resistance. CD44 has multiple isoforms including CD44 standard (CD44s) and CD44 variants (CD44v), which have common and unique functions in tumor development. Therefore, the elucidation of each CD44 isoform’s function in tumor is essential for the establishment of CD44-targeting tumor therapy. We have established various anti-CD44s and anti-CD44v monoclonal antibodies (mAbs) through immunization of CD44v3–10-overexpressed cells. In this study, we established C44Mab-6 (IgG1, kappa), which recognized the CD44 variant 3-encoded region (CD44v3) determined by enzyme-linked immunosorbent assay. C44Mab-6 reacted with CD44v3–10-overexpressed Chinese hamster ovary (CHO)-K1 cells (CHO/CD44v3–10) or some cancer cell lines (COLO205 and HSC-3) by flow cytometry. The apparent KD of C44Mab-6 for CHO/CD44v3–10, COLO205, and HSC-3 was 1.5 × 10−9 M, 6.3 × 10−9 M, and 1.9 × 10−9 M, respectively. C44Mab-6 could detect the CD44v3–10 in western blotting, and stained the formalin-fixed paraffin-embedded tumor sections in immunohistochemistry. These results indicate that C44Mab-6 is useful for detecting CD44v3 in various experiments, and expected for the application of tumor diagnosis and therapy.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

Pancreatic cancer exhibits a poor prognosis due to the lack of early diagnostic biomarkers and the resistance to conventional chemotherapy. CD44 has been known as a cancer stem cell marker, and plays tumor promotion and drug resistance in various cancers. Especially, the splicing variants are overexpressed in many carcinomas, and play essential roles in the cancer stemness, invasiveness or metastasis, and resistance to treatments. Therefore, the understanding of each CD44 variant (CD44v) function and distribution in carcinomas is essential for the establishment of CD44-targeting tumor therapy. In this study, we immunized mice with CD44v3–10-overexpressed Chinese hamster ovary-K1 (CHO) cells, and established various anti-CD44 monoclonal antibodies (mAbs). One of the established clones (C44Mab-3; IgG1, kappa) recognized peptides of the variant 5-encoded region, indicating that C44Mab-3 is a specific mAb for CD44v5. Moreover, C44Mab-3 reacted with CHO/CD44v3–10 cells or pancreatic cancer cell lines (PK-1 and PK-8) by flow cytometry. The apparent KD of C44Mab-3 for CHO/CD44v3–10 and PK-1 was 7.1 × 10−10 M and 1.9 × 10−9 M, respectively. C44Mab-3 could detect the exogenous CD44v3–10 and endogenous CD44v5 in western blotting, and stained the formalin-fixed paraffin-embedded pancreatic cancer cells, but not normal pancreatic epithelial cells in immunohistochemistry. These results indicate that C44Mab-3 is useful for detecting CD44v5 in various applications, and expected for the application of pancreatic cancer diagnosis and therapy.

Introduction: Hemostatic dysfunction during extracorporeal membrane oxygenation (ECMO) due to blood-circuit interaction and the consequences of shear stress by flow rates lead to rapid activation of the coagulation cascade and thrombus formation in the ECMO system and blood vessels. In this study, we aimed to identify the incidence and risk factors for cannula-associated arterial thrombosis (CaAT) post-decannulation. Methods: A retrospective study of patients undergoing arterial cannula removal following ECMO. We evaluated the incidence of CaAT and compared clinical characteristics, pre-ECMO severity, and daily hemostasis parameters in patients with and without CaAT. Multivariate analysis revealed the risk factors for CaAT. Results: Forty-seven patients requiring venoarterial ECMO or hybrid methods were recruited to be screened for thrombosis. The median SOFA score was 11 (8-13). CaAT occurred in 29 patients (61.7%), with thrombosis in the superficial femoral artery accounting for 51.7%. Limb ischemia complications in the group with CaAT was 17.2%. In multivariate analysis, an ECMO flow rate of 100 mL/min was determined to be the independent factor for CaAT with an OR of 0.84 (95% CI, 0.73–0.95, p=0.008). Conclusion: In patients successfully weaned from ECMO, the incidence of CaAT was 61.7%. Our study found that a low-flow rate of ECMO was an independent risk factor for CaAT.

Leishmaniasis is a vector-borne parasitic infection caused by the bite of female Phlebotomine sandflies. World Health Organization (WHO) estimates 100,000 cases to be reported annually on a global scale, moreover, 13 million people were infected between 2010 and 2015 worldwide. Treatment of leishmaniasis by conventional synthetic compounds is met by challenges pertaining to adverse effects which call for the discovery of newer anti-leishmanial molecules. This study was performed to evaluate the effect and modes of action of a sesquiterpene alcoholic molecule Farnesol on Leishmania major, the causative agent of Zoonotic Cutaneous leishmaniasis. The cytotoxic effect of Farnesol against L. major promastigotes, amastigotes and macrophages was assessed by MTT test and counting. The IC50 on promastigotes by Farnesol on L. major was evaluated by flow cytometry. In the findings, Promastigotes were reduced at 167 µM/mL & the mean numbers of L. major amastigotes in macrophages were significantly decreased in exposure to Farnesol at 172 µM/ml. In addition, Farnesol demonstrated no cytotoxicity on macrophages as the IC50 value was 945 µM/ml; it induced significant apoptosis dose-dependent on L. major promastigotes. In silico protein-ligand binding analyses indicated the effect of Farnesol in perturbation of the ergosterol synthesis pathway of Leishmania with attributes suggesting inhibition of Lanosterol-α-demethylase, the terminal enzyme of ergosterol synthesis machinery. Findings from flow cytometry reveal the role of farnesol in apoptosis-induced killing in promastigotes. Farnesol was effective at very lower concentrations when compared to Paromomycin. Further studies are crucial to evaluate the therapeutic potentials of Farnesol alone and in combination with other conventional drugs using clinical settings.

CD44 has been known as a marker of tumor initiating cells, and plays pro-tumorigenic functions in many cancers. The splicing variants play critical roles in malignant progression of cancers by promoting the stemness, cancer cell invasion or metastasis, and resistance to chemo- and radiotherapy. To understand each CD44 variant (CD44v) function is essential to know the property of cancers and establishment of the therapy. However, the function of the variant 4-encoded region has not to be elucidated. Therefore, specific monoclonal antibodies (mAbs) against the variant 4 are indispensable for basic research, tumor diagnosis, and therapy. In this study, we established anti-CD44 variant 4 (CD44v4) monoclonal antibodies (mAbs) by immunizing mice with a peptide containing the variant 4-encoded region. We next performed flow cytometry, western blotting, and immunohistochemistry to characterized them. One of the established clones (C₄₄Mab-108; IgG₁, kappa) reacted with CD44v3-10-overexpressed Chinese hamster ovary-K1 cells (CHO/CD44v3-10). The K_D of C₄₄Mab-108 for CHO/CD44 v3-10 was 3.4 × 10⁻⁷ M. In western blot analysis, C₄₄Mab-108 detected CD44v3-10 in the lysate of CHO/CD44v3-10 cells. Furthermore, C₄₄Mab-108 stained formalin-fixed paraffin-embedded oral squamous carcinoma tissues in immunohistochemistry. These results indicated that C₄₄Mab-108 is useful to detect CD44v4 in various applications.

Background: Current strategies in circulating tumor cell (CTC) isolation in pancreatic cancer heavily rely on the EpCAM and cytokeratin cell status. EpCAM is generally not considered as a good marker given its transitory change during Epithelial to Mesenchymal Transition (EMT) or reverse EMT. There is a need to identify other surface markers to capture the complete repertoire of PDAC CTCs. The primary objective of the study is to characterize alternate surface bi-omarkers to EpCAM on CTCs that express low or negligible levels of surface EpCAM in pancre-atic cancer patients. Methods: Flow cytometry and surface mass spectrometry were used to iden-tify proteins expressed on the surface of PDAC CTCs in culture. CTCs were grown under condi-tions of attachment and in co-culture with naïve neutrophils. Putative biomarkers were then validated in GEMMs and patient samples. Results: Surface proteomic profiling of CTCs identi-fied several novel protein biomarkers. ALCAM was identified as a novel robust marker in GEMM models and in patient samples. Conclusions: We identified several novel surface bi-omarkers on CTCs expressed under differing conditions of culture. ALCAM was validated and identified as a novel alternate surface marker on EpCAMlow CTCs.

A century-old scientific conundrum is solved in this paper. The Prandtl mixing length modelled plane boundary turbulent flow is described by: $\frac{du^+}{d{y^+} }+\kappa^2{y^+} ^2\left( \frac{du^+}{d{y^+} }\right)^2=1$, together with boundary condition $ {y^+} =0:\, u^+=0$. Only an approximate solution to this nonlinear ordinary differential equation (ODE) has been sought so far, however, the exact solution to this ODE has not been obtained. By introducing a transformation, $2\kappa y^+=\sinh \xi$, I successfully find the exact solution of the ODE as follows: $u^+=\frac{1}{\kappa}\ln(2\kappa {y^+} +\sqrt{1+4\kappa^2{y^+} ^2})-\frac{2{y^+} }{1+\sqrt{1+4\kappa^2{y^+} ^2}}$.

The study of a flexible body immersed in a flowing medium is one of best way to find its aerodynamic shape. This Letter revisited the problem first studied by Alben, Shelley and Zhang (Nature 420, 479-481, 2002). The aerodynamic shape of the fibre is found by simpler approach and universal drag scaling laws of the flexible fibre in flowing medium are proposed by using dimensional analysis. The Alben scaling laws is being generalized and confirmed to be universal. Our study show that the Alben number is a measurement of maximum curvature of the fibre forced by dynamic pressure. A complete Maple code is provided for finding aerodynamic shape of the fibre in the flowing medium.

Mechanical properties such as shape, volume and size affect the dynamics of biological systems. Most of the current methodological approaches are inclined to remove the existence of holes and impurities from systems’ description, regarding them as routes toward mechanical failure. On the contrary, we suggest that the occurrence of holes might be of utmost functional importance, allowing reversible transformations of cellular structures. The focus here is on the widespread occurrence of intracytoplasmic holes, that deeply modifies the topology of living cells and provides researchers with novel operational tools to investigate intracellular dynamics. We take as example the prokaryotic gas vesicles, i.e., intracellular cavities filled with gases spreading from the nearby medium. The mechanical and topological cellular properties dictated by intracytoplasmic holes are investigated, focusing on the physical constraints imposed by their very existence. For instance, the presence of gas vesicles breaks the cytoplasmic homogeneity, leading to inhomogeneity in functional activities and modifications in intracellular flows. Also, a topological approach to cytoplasmic holes suggests novel physiological roles for gas vesicles. For example, the gas vesicles’ ability to increase/decrease cellular volumes provides a mechanism that counteracts the detrimental effects of the surface/volume ratio. In conclusion, a structural/methodological approach based on the occurrence of holes testifies once again how the simple biophysical structure alone can dictate the function.

In recent years, excessive heat in the urban texture has become the main problem in the humid and calm wind city of Babolsar with high density, especially in high-rise areas. Therefore, in order to create comfort in this region, it is necessary to establish and continue the wind circulation in space with an environmentally compatible and optimal configuration. The study applies combination of literature, field measurement, experimental validation of CFD simulation output, and comparative analysis. After field measurement and validation of FLOW-3D simulation software (V11.2.2), the relationship between these parameters (height, the width of passages, enclosure between buildings, and buildings' orientation) will be studied which affects the wind’s velocity and direction. The factors of the buildings' orientation and enclosure based on the passages' width have opposite reactions in the direction of the prevailing wind especially from perpendicular side. In this study, two effective factors are on wind velocity: 1- The orientation of the buildings towards the wind flow by creating permeability 2- Reducing the enclosure by increasing the width of the passage's perpendicular to the wind flow (w '= 3w, E' = 0.33E). According to the theoretical and practical study, first, the creation of permeability in the body of the block and the separation of buildings instead of aggregation has been studied, and then reducing the confinement of streets perpendicular to the wind flow has been discussed as effective solutions to improve the wind velocity and circulation between the urban environment.

Systemic sclerosis is an autoimmune disease characterized by organ fibrosis and vasculopathy. Almost all patients suffer from Raynaud’s phenomenon (RP). Currently, several imaging techniques are available; nailfold video capillaroscopy (NVC) is the most widely available, but flow quantification is not possible with NVC. Novel imaging techniques are of interest in this population. We performed a single-center feasibility study using Micro Vascular Imaging (MVI) as a novel imaging technique for flow quantification of small fingertip vessels. We compared a group of 20 healthy controls (HCs) with 20 Systemic Sclerosis (SSc) patients. In HCs, flow measurements assessed with MVI were statistically significantly higher in individual fingers and combined for all fingers (p&lt;0.0001). As a cut-off value to discriminate HCs from SSc, a peak systolic (PS) flow velocity of &lt;6.9 cm/s and an end-diastolic (ED) flow velocity of &lt;2.68 cm/s was determined. Test characteristics for PS flow velocity showed moderate sensitivity (0.69, 95% CI 0.58-0.78) but high specificity (0.88, 95% CI 0.79-0.93). Similar test characteristics for ED flow velocity were obtained. The optimal cut-off point was estimated at &lt;2.68 cm/s, sensitivity was moderate (0.65, 95% CI 0.53-0.75), specificity was 0.80 (95% CI 0.70-0.87). Here, we present the first study on the use of MVI to assess blood flow in the fingertips with high specificity in SSc patients. Future studies need to investigate correlations with the risk for organ complications, such as digital ulcers or pulmonary arterial hypertension.

Fluid flow and chemokine gradients play a large part in not only regulating homeostatic processes in the brain, but also in pathologic conditions by directing cell migration. Tumor cells in particular are superior at invading into the brain resulting in tumor recurrence. One mechanism that governs cellular invasion is autologous chemotaxis, whereby pericellular chemokine gradients form due to interstitial fluid flow (IFF) leading cells to migrate up the gradient. Glioma cells have been shown to specifically use CXCL12 to increase their invasion under heightened interstitial flow. Computational modeling of this gradient offers better insight into the extent of its development around single cells, yet very few conditions have been modelled. In this paper, a computational model is developed to investigate how a CXCL12 gradient may form around a tumor cell and what conditions are necessary to affect its formation. Through finite element analysis using COMSOL and coupled convection-diffusion/mass transport equations, we show that velocity (IFF magnitude) has the largest parametric effect on gradient formation, multidirectional fluid flow causes gradient formation in the direction of the resultant which is governed by IFF magnitude, common treatments and flow patterns have a spatiotemporal effect on pericellular gradients, exogenous background concentrations can abrogate the autologous effect depending on how close the cell is to the source, that there is a minimal distance away from the tumor border required for a single cell to establish an autologous gradient, and finally that the development of a gradient formation is highly dependent on specific cell morphology.

The use of convolutional neural networks (CNNs) in image classification has become the standard method of approaching computer vision problems. Here we apply pre-trained networks to classify images of non-breaking, plunging and spilling breaking waves. The CNNs are used as basic feature extractors and a classifier is then trained on top of these networks. The dynamic nature of breaking waves is exploited by using image sequences to gain extra information and improve the classification results. We also see improved classification performance in using pre-computed image features such as the optical flow between image pairs. The inclusion of the dynamic information improves the classification between breaking wave classes. We also provide corrections to the methodology from the article from which the data originates to achieve a more accurate assessment of performance.

Self-organized criticality (SOC) is a celebrated paradigm from the 90’s for understanding dynamical systems naturally driven to its critical point, where the power-law dynamics taking place make predictions practically impossible, such as in stock prices, earthquakes, pandemics and many other problems in science related to phase transitions. Shortly thereafter, it was realized that traffic flow might be in the SOC category, implying that conventional traffic management strategies seeking to maximize the local flows can become detrimental. This paper shows that the Kinematic Wave model with triangular fundamental diagram, and many other related traffic models, indeed exhibit SOC, thanks in part to the fractal nature of traffic exposed here on the one hand, and our need to get to our destinations as soon as possible, on the other hand. Important implications for congestion management of traffic near the critical region are discussed, such as: (i) Jam sizes obey a power-law distribution with exponent 1/2, implying that both its mean and variance become ill-defined and therefore impossible to estimate. (ii) Traffic in the critical region is chaotic in the sense that predictions becomes extremely sensitive to initial conditions. (iii) However, aggregate measures of performance such as delays and average speeds are not heavy tailed, and can be characterized exactly by different scalings of the Airy distribution, (iv) Traffic state time-space “heat maps” are self-affine fractals where the basic unit is a triangle, in the shape of the fundamental diagram, containing 3 traffic states: voids, capacity and jams. This fractal nature of traffic flow calls for analysis methods currently not used in our field.

Yam (Dioscorea spp.) is a monocotyledonous herbaceous vine plant grown in the tropics and subtropics. It is a multi-species plant with varied intra- and interspecific ploidy levels. Of the 600 species, 11 are cultivated staple supporting the livelihood of over 300 million people. The paucity of information on ploidy and the genomic constitution is a significant challenge to the crop’s genetic improvement through crossbreeding. The objective of this study was to investigate the ploidy levels of 236 accessions across six cultivated and two wild species using chromosome counting, flow cytometry and genotyping-based ploidy determination methods. Results obtained from chromosome counting and genotyping-based ploidy determination were in agreement. In majority of the accessions, chromosome counting and flow cytometry were congruent, allowing future rapid screening of ploidy levels using flow cytometry. Among cultivated accessions, 168 (71%) were diploid, 50 (21%) were triploid, and 12 (5%) were tetraploid. Two wild species included in the study were diploids. Resolution of ploidy level in yams offers opportunities for implementing successful breeding programmes through intra- and inter-specific hybridization.

Understanding how the deformed bed topography induced by near-bank vegetation impacts the hydrodynamics is significant for understanding the maintenance condition of bed morphology and further fluvial evolution. This issue has rarely been addressed by current studies. This study with a 2D hydro-morphological model investigates the hydrodynamics over flat and deformed beds with a near-bank vegetation patch. By varying the patch density, the generalized results show that the hydrodynamics for the deformed bed differs a lot from those for the flat bed. It is found that deformed bed topography leads to an apparent decrease in longitudinal velocity and bed shear stress in the open region and longitudinal surface gradient for the entire vegetated reach. However, the transverse flow motion and transverse surface gradient in the region of the leading edge and trailing edge is enhanced or maintained, suggesting the strengthening of secondary flows. Interestingly, the deformed bed topography tends to alleviate the turbulent effect caused by the junction-interface horizontal coherent vortices, indicating that the turbulence-induced flow mixing is highly inhibited by the deformed bed. Alternatively, the enhanced secondary flows might provide compensation for the flow mixing for the deformed bed, confirmed by a faster recovery of the redistributed water discharge for the vegetated and open regions to the normal value (50%). The interior flow adjustment through the patch for the deformed bed requires a shorter distance, which links the vegetative drag length with a logarithmic relation. The tilting bed topographic effect in the open region to accelerate the flow may account for the faster flow adjustment.

Climate change plays a pivotal role in the hydrology of tributaries in the upper Blue Nile basin. This study was designed to reveal the extent to which climate change impacts on stream flow of the Gumara watershed under the Representative Concentration Pathway (RCP) climate change scenario. The study considered the RCP 2.6, RCP 4.5 and RCP 8.5 scenarios using the second generation Canadian Earth System Model (CanESM2). The Statistical Downscaling Model (SDSM) was used for calibration and projection of future climatic data of the study area. Soil and Water Assessment Tool (SWAT) model was used for simulation of the future stream flow of the watershed. Result showed that the average temperature will be increasing by 0.84oC, 2.6oC and 4.1oC in the end of this century under RCP 2.6, RCP 4.5 and RCP 8.5 scenarios respectively. The change in monthly rainfall amount showed a fluctuating trend in all scenarios but the overall annual rainfall amount is projected to increase by 8.6%, 5.2% and 7.3% in RCP 2.6, RCP 4.5, and RCP 8.5 respectively. Overall, this study revealed that, due to climate change, the stream flow of the watershed is found to be increasing by 4.06%, 3.26%, and 3.67% under RCP 2.6, RCP 4.5 and RCP 8.5 scenarios respectively.

The purpose of this paper is to simulate a two-dimensional Rayleigh-Taylor instability problem using the classical method of Finite Element analysis of a multiphase model using ANSYS FLUENT 19.2. The governing equations consist of a system of coupled nonlinear partial differential equations for conservation of mass, momentum and phase transport equations. The study focuses on the transient state simulation of Rayleigh Taylor waves and subsequent turbulent mixing in the two phases incorporated in the model. The Rayleigh Taylor instability is an instability of an interface between two fluids of different densities which occurs when the lighter fluid is pushing the heavier fluid in a gravitational field. The problem was governed by the Navier-Stokes and Cahn-Hilliard equations in a primitive variable formulation. The Cahn- Hilliard equations were used to capture the interface between two fluids systems. The objective of this article is to perform grid dependency test on Rayleigh Taylor Instability for 2 different mesh size and compare the results for the variation in Atwood Number. The results were validated with the observations from previous published literatures.

The present study explored the effects of a Second-generation mindfulness-based intervention known as Flow Meditation (Meditación-Fluir) in the improvement of life habits. A sample of university students (n = 51) in Spain were randomly assigned to a seven-week mindfulness treatment or a waiting list control group. Results showed that compared to the control group, individuals in the mindfulness group demonstrated significant improvements across all outcome measures, including healthy eating habits (balanced diet, intake rate, snacking between meals, decrease in consumption by emotional states negative, increased consumption by negative emotional states, amount of consumption, meal times, consumption of low-fat products), tobacco, alcohol and cannabis consumption, and resting habits. There were differences between males and females in some of these variables and a better effect of the treatment was evident in the females of the experimental group as compared to males. The Flow Meditation program shows promise for fostering healthy life habits, thus decreasing behaviors related to maladaptive eating, tobacco, alcohol and drug consumption, as well as negative resting habits, in university students. This mindfulness program can significantly contribute in the treatment of eating disorders and addictions, wherein negative emotional states and impulsivity are central features of the condition.

In tracking-by-detection paradigm for multi-target tracking, target association is modeled as an optimization problem that is usually solved through network flow formulation. In this paper, we proposed combinatorial optimization formulation and used a bipartite graph matching for associating the targets in the consecutive frames. Usually, the target of interest is represented in a bounding box and track the whole box as a single entity. However, in the case of humans, the body goes through complex articulation and occlusion that severely deteriorate the tracking performance. To partially tackle the problem of occlusion, we argue that tracking the rigid body organ could lead to better tracking performance compared to the whole body tracking. Based on this assumption, we generated the target hypothesis of only the spatial locations of person’s heads in every frame. After the localization of head location, a constant velocity motion model is used for the temporal evolution of the targets in the visual scene. Qualitative results are evaluated on four challenging video surveillance dataset and promising results has been achieved.

Objective: To investigate the effects and mechanisms of different concentrations of CCCP on mitophagy in human peripheral blood regulatory T cells. Methods: Tregs were isolated, identified and then grouped, treating with CCCP at a concentration of 2.5 μM, 5 μM, 10 μM, 20 μM and 40 μM for 24h in an incubator. Flow cytometry detected the reactive oxygen species (ROS), mitochondrial membrane potential (MMP), mitochondrial quality, and fluorescence microscopy observed the co-localization of mitochondria and lysosomes in each group. Results: The purity of CD4⁺CD25⁺Tregs was (93.36 ± 1.87) %. With the increase of CCCP concentration, the level of ROS gradually increased, while the MMP decreased gradually. About the mitochondria and lysosome fusion, the fluorescence intensity of orange (yellow) was the highest when the concentration of CCCP was in the range of 5-10 μM while decreased with the CCCP concentration continually increasing. The mitochondrial quality decreased with the increase of CCCP concentration. However, there was no significant difference between groups C, D and E. The mitochondrial quality of groups F and G were significantly lower than that of group E. Conclusions: With the concentration of CCCP gradually increased, the level of ROS in Treg cells increased, and MMP decreased, which promoted the mitophagy, mitochondrial quality maintains homeostasis; When ROS accumulated, and MMP decreased significantly, the mitophagy was inhibited, and the mitochondrial quality was significantly decreased.

The operation feasibility of small hydropower plants in mountainous sites is subjected to the run-of-river flow which is also depending on a high variability in precipitation and snow cover. Moreover, the management of this kind of systems has to be performed with some particular operation conditions of the plant (e.g. turbine minimum and maximum discharge) but also some environmental flow requirements. In this context, a technological climate service is conceived in tight connection with end users, perfectly answering the needs of the management of small hydropower systems in a pilot area, and providing forecast of river streamflow together with other operation data. This paper presents an overview of the service but also a set of lessons learnt related to features, requirements and considerations to bear in mind from the point of view of climate services developers. In addition, the outcomes give insight into how this kind of services could change the traditional management (normally based on the past experience), providing a probability range of future river flow based on future weather scenarios according to the range of future weather possibilities. This highlights the utility of the co-generation process to implement climate services for water and energy fields but also that seasonal climate forecast could improve the business as usual of this kind of facilities.

A debris flows generation related to a poorly sorted mixture of soil, catchment topography and rainfall characteristic. Runoff of some depth on valley resulting from intensive rainfall can incur the sediments movement of beds or adjacent banks. The fluid flow in channel affected by rainfall parameters combinations, such as duration, intensity, cumulative rainfall, etc., is the key factor for debris movement. In this paper, the rainfall characteristics and occurrence conditions of debris flow in Xiongmao gully on July, 26th, 2016, have been explored, combined with field survey and indoor simulation experiment on the collected critical discharge parameters of debris movement. Further, debris distribution and the critical discharge characteristics have been analysed, by means of investigation on the catchment topography and occurrence cause of the debris flow, analysis of the critical discharge parameters on which the channel debris began to move, and K value clustering analysis method to characterize the rainfall pattern of the studied area, the discharge calculation of debris flow occurring in different rainfall patterns. The results have shown that, for the debris flow occurrence in Xiongmao gully, the debris initiation on the middle reaches of the gully provide the majority of solid particles for the disaster on July, 26th, 2016, and the upstream confluent provided catchment. Based on the relationship obtained from laboratory test, in which the calculated critical discharge was 43.8m3/s, less than the peak discharge (Qc =66.7m3/s), calculated by morphological method. In addition, it has been indicated that the dominated rainfall patterns of the studied area are first-quartile and second-quartile, that is, the rainfall is primarily at earlier or middle to preliminary stage of this time rainfall event. The critical discharge for the occurrence of debris flow on July, 26th was achieved 20a rainfall frequency, the larger runoff volume generated on shorten heavily rainfall. Based on individuality characteristics, such as distributed hydrological analysis, critical discharge and rainfall pattern of debris flow, the forewarning could be more efficient.

In the present paper, a measure of the influence of irregularities of the underlying surface (for instance, the real terrain profile) on the dynamics of air flow is estimated. It is shown that these irregularities significantly perturbing the pressure, density, velocity and temperature of air flow; for perturbed pressure, density, velocity and temperature of air flow the closed formulas in the Fourier integral form are obtained. In addition, in the present paper, it is proved that due to these perturbations, at a certain altitude of the atmosphere some surface of the "sturdy wall" form appears, on which the vertical and horizontal components of the air flow velocity become infinitesimal and infinitely large, respectively.

The paper argues that universal approaches to infiltration and drainage in permeable media that pivot around capillarity and that led to dual porosity, non-equilibrium, or preferential flow need to be replaced by a dual process approach. One process has to account for relatively fast infiltration and drainage based on Newton's shear flow, while the other one is responsible for storage and relatively slow redistribution of soil water by focusing on capillarity. Already Schumacher (1864) postulated two separate processes. However, Buckingham's (1907) and Richards' (1931) apparent universal capillary-based approach to flow and storage of water in soils dominated. The paper introduces the basics of Newton's shear flow in permeable media. It presents experimental support for the four presumptions of (i) sharp wetting shock fronts; (ii) that move with constant velocities; (iii) atmospheric pressure prevails behind the wetting shock front; (iv) laminar flow. It further discusses the scale tolerance of the approach, its relationship to Darcy's (1856) law, and its extension to solute transport.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

Several transgenic rice lines have been developed and are currently under field trials around the world. There are future plans for the commercial release of transgenic rice into the environment. Rice is an autogamous plant and therefore not perceived to be a very high candidate for pollen mediated gene flow to wild and weedy relatives. However, in a tropical environment like Ghana, where sexually compatible wild Oryza species which belongs to the AA genome are present within the ecology of cultivated rice, the possibility of gene flow to wild species cannot be overlooked. There is little evidence on gene flow and its consequences on the wild rice species should they acquire useful genes through gene flow. This review discusses the chances of cultivated to wild rice gene flow in Ghana and the biosafety considerations that should be put in place before the commercial release of genetically modified (GM) rice.

The calculation of power flow in power systems with the presence of harmonics has been properly studied in the scientific literature. However, power flow calculation considering interharmonic components is still an open question. Traditional methods based on the IEEE1459 standard have proven to be valid and accurate only for linear and sinusoidal systems, but have been criticized for non-linear and non-sinusoidal systems because they are not able to explain correctly the current and voltage interactions beyond the active power. This paper proposes the use of a novel mathematical framework called geometric algebra (GA) to study the power flow considering the interaction of current and voltage harmonics and interharmonics. The use of GA enables the precise determination of the direction and magnitude of the total and single active power flow for each component, as well as other power elements related to the non-active power due to cross interaction. Moreover, this paper makes a novel contribution to the definition of interharmonics in geometric algebra space that has not been done before. To test the validity of the method, both linear and non-linear circuits are proposed and solved by applying voltages and currents with harmonic and interharmonic components. The results obtained show that power flow can be analyzed under the prism of the principle of energy conservation (PoCoE) in a way that allows a better understanding of the power spectrum due to the interaction of harmonics and interharmonics of voltage and current.

_{Superconducting foams of YBa$_2$Cu$_3$O$_y$ (YBCO) are proposed as trapped field magnets or supermagnets. The foams with an open-porous structure are light-weight, mechanically strong and can be prepared in large sample sizes. The trapped field distributions were measured using a scanning Hall probe on various sides of an YBCO foam sample after field-cooling in a magnetic field of 0.5 T produced by a square Nd-Fe-B permanent magnet. The maximum trapped field (TF) measured is about 400 G (77 K) at the bottom of the sample. Several details of the TF distribution, the current flow and possible applicatons of such superconducting foam samples in space applications, e.g., as active elements in flux-pinning docking interfaces (FPDI) or as portable strong magnets to collect debris in space, are outlined.}

A method of solution to solve the compressible unsteady 3D Navier-Stokes Equations in cylindrical co-ordinates coupled to the continuity equation in cylindrical coordinates is presented in terms of an additive solution of the three principle directions in the radial, azimuthal and z directions of flow. A dimensionless parameter is introduced whereby in the large limit case a method of solution is sought for in the boundary layer of the tube. A reduction to a single partial differential equation is possible and integral calculus methods are applied for the case of a body force directed to the centre of the tube to obtain an integral form of the Hunter-Saxton equation. Also an extension for a more general body force is shown where in addition there is a rotational force applied.

The main objective was to determine the effect of mobile phone radiation on general health and electrolytes among students who use mobile phones. A questionnaire was designed and applied to 103 healthy and 36 deaf female students to select cases that meeting the inclusion criteria. For assessment of salivary parameters, the participants were classified into three groups. Group I was the control group, which included 17 deaf students. Group II was healthy students who have mobile phone for less than 5 years. Group III was healthy students who have mobile phone for 5 years or more. The results showed that the participants who use mobile phone had several problems in their health including dry mouth, bad odor from mouth, drooling of saliva, as well as ear and eye pain. The participants who use mobile phone complained of headache, anxiety and forgetfulness as compared to deaf participants. The study showed that there was no significant difference between pH and flow rate of saliva in all tested groups. This study has also shown that salivary level of Na+ and K+ were significantly lower in mobile phone users when compared to non users of mobile phone.

The dynamics of a spherical particle in an asymmetric serpentine is studied by finite element method (FEM) simulations in a physically unconstrained system. The two-way coupled time dependent solutions illustrate the path of the particle along a curve where a secondary flow (Dean flow) has developed. The simulated conditions were adjusted to match those of an experiment for which particles were focused under inertial focusing conditions. The obtained rotational modes allowed to infer the influence of the local flow around the particle. We propose a new approach to find the decoupled secondary flow contribution employing a quasi-Stokes flow.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

The aerodynamic efficiency of a NACA 0012 AR 4 wing was affected through periodic contours aligned in the flow direction resembling a “wrinkled” texture. Streamwise and cross-stream Particle Image Velocimetry (PIV) were conducted at the University of Dayton Low Speed Wind Tunnel (UD-LSWT) around Reynolds number of 135,000 on the NACA 0012 AR 4 wing with and without surface contours. Wings with 6 contour sections was designed by spline fitting two NACA 0012 airfoil profiles in the spanwise direction. Both 2D (wall-to-wall model) configuration and 3D configuration of the wings were tested to determine the effects of surface contours on the parasite and induced drag of the wing. Streamwise PIV results indicated an increase in momentum deficit in the wake of the mid-contour region due to enhanced boundary layer separation from the upper surface of the mid-contour region. The cross-stream PIV results indicated a decrease in the magnitude of azimuthal velocity, circulation and RMS quantities in the wingtip vortex with the surface contours. The reduction in the wingtip vortex properties indicates that the contours were effective in blocking the spanwise flow feeding into the wingtip vortex on the surface of the wing

On 5-7 April 2018 a landfalling atmospheric river resulted in widespread heavy precipitation in the Sierra Nevada of California and Nevada. Observed snow levels during this event were among the highest snow levels recorded since observations began in 2002 and exceeded 2.75 km for 31 hours in the northern Sierra Nevada and 3.75 km for 12 hours in the southern Sierra Nevada. The anomalously high snow levels and over 80 mm of precipitation caused flooding, debris flows, and wet snow avalanches in the upper elevations of the Sierra Nevada. The origin of this atmospheric river was super typhoon Jelawat, whose moisture remnants were entrained and maintained by an extratropical cyclone in the northeast Pacific. This event was notable due to its April occurrence, as six other typhoon remnants that caused heavy precipitation with high snow levels (mean = 2.92 km) in the northern Sierra Nevada all occurred during October.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

Reducing carbon emissions is a major ways to achieving green development and sustainability for China’s future. This paper elaborates the detailed feature of China's carbon flow for 2013 with the carbon flow chart and gives changing characteristics of China's CO₂ flow from the viewpoint of sector and energy during 2000 and 2013. The results show that (1) during 2000 to 2013, China's CO₂ emissions with the approximately growth portion of 9% annually, while the CO₂ intensity of China diminishes at different rates. (2) The CO₂ emissions from secondary industry are prominent from the perspective of four main sectors accounting for 83.5%. The manufacturing play an important part in the secondary industry with 45%. In which the "smelting and pressing of metal" takes up a large percentage as about 50% in manufacturing. (3) The CO₂ emissions produced by coal consumption is keep dominant in energy-related emissions with a contribution of 65%, while it will decrease in the future. (4) From the aspect of sector, the CO₂ emissions mainly come from the "electricity and heating" sector and the "smelting and pressing of metals" sub-sector. While it is essential and urgent to propose concrete recommendations for CO₂ emissions mitigation. Firstly, the progression of creative technology is inevitable and undeniable. Secondly, the government should make different CO₂ emissions reduction policies among different sectors. For example, the process emission plays an important role in "non-metallic mineral" while in "smelting and manufacturing of metals" it is energy. Thirdly, the country can change the energy structure and promote renewable energy for powering by wind or other low-carbon energy. Besides it, the coke oven gas can be a feasible substitution. Finally, policy maker should be aware of the emissions from residents have been growing in a fast rate. It is effective to involve the public in the activity of energy conservation and carbon emissions reduction such as reducing the times of personal transportation.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

A pump station is a very important flood control facility for mitigating inundation of urban lowland areas. It is not easy to secure a site to increase the capacity of a pump station in an urban area because of various limitations or to maximize the discharge capacity of the pump sump. Adding a facility to improve the pump capacity of a pump station may affect the flow characteristics, such as unexpected increases in the flow velocity and vorticity, and cause severe problems with operating the pump station. To solve those problems, anti-vortex devices (AVDs) have been developed and adopted for appropriate design standards. The Korean design criteria for AVDs are based on experience and foreign standards because not enough data on the AVD are available. In this study, the flow in the sump was numerically simulated at various AVD heights to collect information on improving the design and efficiency of a pump station. Consequently, an appropriate height for the AVD and changes in the flow pattern and vortex in the pump sump were determined and compared with 12 cases of inflow conditions with respect to the vertical location.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Background: A Morel–Lavallée lesion (MLL) is a traumatic, internal closed degloving injury that results from shearing of subcutaneous tissue away from underlying fascia, usually associated with high-velocity trauma. Case presentation: A 52-year-old man was transported to hospital for further follow-up of a superficial femoral artery injury. Examination on admission showed bruising seen around the left thigh. Contrast-enhanced computed tomography of the left thigh revealed hematoma with extravasation from a branch of the left superficial femoral artery, but no apparent aneurysms or femoral fractures. The patient was treated with compression bandages and discharged on hospital day 6. He left hospital able to walk unaided. He subsequently complained of left thigh pain with swelling and visited the hospital several times. He was treated at another outpatient clinic and was diagnosed with MLL. Single-use disposable portable negative pressure wound therapy (NPWT) was applied for about 2 months, achieving a stable wound site. Conclusion: We encountered a case of MLL successfully treated with single-use portable NPWT. This report presents the case of a patient with isolated MLL without fracture in the left thigh, in which the diagnosis was missed on initial admission. Finally, the patient received minor interventions including drainage along with tissue debridement and portable NPWT. We reviewed the relevant literature and summarize the pathogenesis, clinical manifestations, and treatment strategies for MLL. Emergency physicians require an increased understanding of MLL to avoid misdiagnosis and missed diagnosis.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO₂ has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O^2-, ·OH), yet the low specific surface area of crystalline TiO₂ depressed the catalytic performance. Herein, we prepared TiO₂ aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO₂ aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO₂ aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO₂ aerogel for the photocatalytic HCHO decomposition is 2 nm~10 nm. This study provides a theoretical idea for TiO₂ aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO₂ aerogels for green chemistry.

Hazelnut, pistachio and cashew are tree nuts with health benefits but also with allergenic properties being prevalent food allergens in Europe. The allergic characteristics of these tree nuts after processing combining heat, pressure and enzymatic digestion were analyzed through in vitro (Western blot and ELISA) and in vivo test (Prick-Prick). In the analyzed population, the patients sensitized to Cor a 8 (nsLTP) were predominant over those sensitized against hazelnut seed storage proteins (Sprot, Cor a 9 and 14), which displayed higher IgE reactivity. The protease E5 effectively hydrolyzed proteins from hazelnut and pistachio, while E7 was efficient for cashew protein hydrolysis. When combined with pressured heating (autoclave and Controlled Instantaneous Depressurization (DIC)), these proteases notably reduced the allergenic reactivity. The combination of DIC treatment before enzymatic digestion resulted in the most effective methodology to drastically reduce or indeed eliminate the allergenic capacity of tree nuts.

Recent research has specifically targeted the decision-making process of eco-friendly individuals, emphasizing the significance of recycling and its impact on sustainability. Our study extends this inquiry by examining the correlation between recycling participation and pro-environmental behavior among consumers, integrating the concepts of self-efficacy, feelings of pride, and social pressure into our analysis. Utilizing Partial Least Squares-Structural Equation Modeling (PLS-SEM), we aimed to explore the intricate relationships that underpin these behaviors. Results suggest that self-efficacy and feelings of pride significantly influence individuals' recycling behaviors, highlighting the role of psychological and social factors in promoting environmental sustainability. Interestingly, it was concluded that social pressure did not have the expected moderating effect on increasing consumers' feelings of pride and self-efficacy toward recycling activities.This study not only sheds light on the underlying mechanisms that drive pro-environmental actions but also contributes to understanding sustainability promotion through recycling and offers insights for policymakers and environmental advocates to foster environmental responsibility and behavior change.

The right heart catheterisation constitutes the gold standard for pulmonary hypertension (PH) diagnosis. However, echocardiography remains a reliable, non-invasive, inexpensive, convenient, and easily reproducible modality not only for the preliminary screening of PH but also for PH prognosis. The aim of this review is to describe a cluster of echocardiographic parameters for the detection and prognosis of PH and analyse the challenges of echocardiography implementation in patients with suspected or established PH. The most important echocardiographic index is the calculation of pulmonary arterial systolic pressure (PASP) through the tricuspid regurgitation (TR). It has shown high correlation with invasive measurement of pulmonary pressure, but several drawbacks have questioned its accuracy. Besides this, the right ventricular outflow track acceleration time (RVOT-AT) has been proposed for PH diagnosis. A plethora of echocardiographic indices: right atrial area, pericardial effusion, the tricuspid annular plane systolic excursion (TAPSE), the TAPSE/PASP ratio, tricuspid annular systolic velocity (s′) and recently, can reflect the severity and prognosis of PH. Recent advances in echocardiography with 3-dimensional right ventricular (RV) ejection fraction, RV free wall strain and right atrial strain may further assist the prognostication of PH.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

Sorghum-nematode interactions were previously purported to produce chemicals that confer pre-infectional nematode resistance to the infective second-stage juveniles (J2) of the root-knot (Meloidogyne species) nematodes in the rhizosphere, without any contact to J2 bodies. We tested the null hypothesis in four sorghum cultivars with a wide range of pre-infectional nematode resistance relative to the susceptible tomato cultivar. Post a 56-day exposure of Meloidogyne enterolobii, J2 from soil and root samples were subjected to step-wise fixative solutions and then mounted on slides. Length-related and diameter-related morphometrics were measured using an OMAX microscope – equipped with a digital measuring software. The study was conducted over two seasons and the seasonal interactions on morphometrics were not significant. Relative to the tomato cultivar, sorghum treatments generally increased the length-related morphometrics, but decreased the diameter-related variables in both soil J2 and root J2. The null hypothesis was therefore rejected in favour to the assumption that upon exposure of J2 bodies to botanical chemicals in both soil and root samples, with certain morphometrics being adjusted to ameliorate the potential damage of hydrostatic pressure on internal organs of the infective juveniles. In conclusion, in pre-infectional nematode resistance, J2 bridge chemicals in the rhizosphere and enter the root system, where chemicals still have effects on morphometrics of nematodes.

In Mexico, the evaluations of environmental flows are regulated by the Mexican Norm NMX-AA-159-SCFI-2012 and they warrant the establishment of water reserves for the environment. Yet, the pressure for water use limits the establishment of said reserves. This research aimed to evaluate the changes through time of the variables that serve as a basis for the implementation strategy by the Mexican government. A geographical information system was built with updated variables, the desired conservation status was analyzed, and the potential reserves were estimated based on the reference values for all basins nationwide. The results were examined according to their historical, current, and potential contribution to the conservation of natural protected areas and their connectivity. The outcomes point towards an administrative implementation strategy with positive outcomes despite the growing pressure for water use, with a change rate higher than the one for the creation of new protected areas. Currently, basins with low pressure and high conservation value have the potential to contribute to 86–88% of the goal set by the present administration without affecting water availability. Finally, reserving water in the priority basins would guarantee the legal protection of the flow regime in 48–50% of the hydrographic network in a desired conservation status, 45–49% of wetlands of international importance, and other natural protected areas in 85–89% of the global ecoregions represented in Mexico.

This study investigates the suitability of the timestamp approach algorithm for predicting blood pressure (BP) using wearable and comfortable devices, showcasing its accuracy even with low-frequency sampled signals. Developed within the SINTEC European project, the algorithm utilizes Electrocardiogram (ECG) and Photoplethysmogram (PPG) sensors, demonstrating promising results in both laboratory and hospital settings. The research emphasizes the algorithm’s potential to transform continuous and non-invasive BP monitoring through wearable technology, offering frequent measurements with minimal discomfort. While the study shows promise, further exploration is needed, focusing on optimizing machine learning coefficients for long-term monitoring applications and addressing potential changes over time. Technological improvements, including the implementation of edge computing algorithms, hold the key to enhancing BP accuracy, denoising techniques, and integrating alarm systems for future wearable solutions. This study emphasizes the adaptability of the algorithm for diverse healthcare environments, paving the way for broader applications in convenient and reliable BP monitoring.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Gabapentin (GBP), a GABA analogue, is primarily used as an anticonvulsant to treat partial seizures and neuropathic pain. While a majority of the side effects are associated with the nervous system, emerging evidence suggests a high risk for heart diseases in the patients taking GBP. In the present study, we used a preclinical model of rats to investigate (1) the acute cardiovascular responses to GBP (bolus i.v. injection, 50 mg/kg) and (2) the effects of chronic GBP treatment (i.p. 100 mg/kg/day x 7 days) on cardiovascular function and the myocardial proteome. Under isoflurane-anesthesia, rat blood pressure (BP), heart rate (HR), and left ventricular (LV) hemodynamics were measured using Millar pressure transducers. The LV myocardium and brain cortex were analyzed by proteomics, bioinformatics, and western blot to explore the molecular mechanisms underlying GBP-induced cardiac dysfunction. In experiment (1), we found that i.v. GBP significantly decreased BP, HR, maximal LV pressure, and maximal and minimal dP/dt, whereas it increased IRP-AdP/dt, Tau, systolic, diastolic, and cycle durations (*p < 0.05 and **p < 0.01 vs baseline; n = 4/group). In experiment (2), we found that chronic GBP treatment resulted in hypotension, bradycardia, and LV systolic dysfunction, with no change in plasma norepinephrine. In the myocardium, we identified 109 differentially expressed proteins involved in calcium pathways, cholesterol metabolism, and galactose metabolism. Particularly, we found that calmodulin, a key protein of intracellular calcium signaling, was significantly upregulated by GBP in the heart but not in the brain. In summary, we found that acute and chronic GBP treatments suppressed cardiovascular function in rats, which is attributed to abnormal calcium signaling in cardiomyocytes. These data reveal a novel side effect of GBP independent of the nervous system, providing important translational evidence to suggest that GBP can evoke adverse cardiovascular events by depression of myocardial function.

In this paper we overview all analytical engineering solutions for corrosion problems in pressure vessels delivered over the past 60 years. We briefly detail strengths and weaknesses of existing approaches, thus demonstrating the need for novel uniform corrosion analysis methods for both current and new applications. To complement the review, we also present a new analytical model allowing to estimate the lifetime of pressured elastic vessels with mechanically assisted corrosion. Both internal/external pressure and internal/external corrosion are captured and dissolution driven corrosion is also considered. The readily implemented method improves existing analytical approaches and is shown to be effective for thin and thick shells, as well as various loading and corrosion intensity and geometrical conditions.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

Background: COVID-19 pneumonia caused by SARS-Cov-2 virus induces alveolar collapse and hypoxia that may become severe. The aim of the study is to analyze the effects of chest physiotherapy using a threshold valve in patients with acute respiratory failure due to COVID-19 pneumonia. Methods; Retrospective observational study, in hospitalized patients from March to May 2020. Breathing exercises were performed with a threshold valve of 10 cmH2O. Fraction of inspired oxygen, oxygen saturation, heart rate, respiratory rate and dyspnea were collected before and after the first session and at the end of the 5th day of chest physiotherapy treatment. Results: The final sample included 125 patients. Significant differences (p&lt;0.01) were found in the pre-post intervention SpO2/FiO2 ratio (250±88.4 vs 275.6±97.5, p&lt;0.001), reaching 354.4±110.2 after 5 days of therapy (p&lt;0.001 with respect to baseline). Mean baseline respiratory, heart rate and level of dyspnea measure by the Borg scale did not change during the technique performance. In patient maneuvers with FiO2&gt;0.4, the SaO2/FiO2 ratio increase was higher than in patients with milder severity (46.85 ± 77.69, p&lt;0.01). Conclusions: Chest physiotherapy with a 10 cmH2O threshold valve is a safe and tolerated intervention with short-term improvement in oxygenation in patients with COVID-19 pneumonia.

Background: In recent years, the assessment and guidance of cardiopulmonary resuscitation (CPR) quality using noninvasive and invasive monitoring techniques have been increasingly recommended. In this study, we introduce a new physiological monitoring system that simultaneously measures arterial pressure (AP), venous pressure (VP), and cerebral tissue oxygen saturation (SctO2) during CPR. Methods: This prospective observational study was conducted at a single center (Kagoshima City Hospital). Adult out-of-hospital patients aged ≥18 years with an intravenous femoral arterial line, venous line, and SctO2 monitor were included. We measured femoral arterial pressure (FAP) and femoral venous pressure (FVP) invasively if catheters were immediately inserted into the femoral artery and vein for potential candidates who require interventions such as extracorporeal cardiopulmonary resuscitation but did not receive such interventions as a result. Results: We observed several representative cases that provided the following insights: We presented several cases, including two patients with significant increases in FVP and low SctO2 values, and in both cases, return of spontaneous circulation (ROSC) was not achieved. In contrast, we also presented two cases in which CPR resulted in higher FAP compared to FVP and an upward trend in SctO2 values was observed, and both instances achieved ROSC. Conclusion: We presented a simultaneous physiological monitoring system that can monitor AP, VP, and SctO2 during CPR. Further case accumulations will be necessary to assess the variations in hemodynamic status during CPR and the association between each hemodynamic status and outcomes after cardiac arrest.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

In this paper, we investigated the capacitive effect and the electromagnetic coupling on the measurement chain induced by the gas gun or the powder gun during impact experiments. Reduced bandwidth and noise have been noticed on experimental signals. Rogowski coil measurements have been added on the cables to characterize the electromagnetic coupling. The perturbation currents on the cables have been quantified depending on the configuration. The gauge, the transmission line and the conditioning system have been modeled. The calculations have reproduced the electrical wave arrival time, the transmission line transfer impedance, the conditioning system transfer impedance and it shows the bandwidth limitation. A capacitive effect with the piezoresistive manganin gauge embedded into the sample has been identified depending on the experimental setup.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

Abstract: Background: Non-invasive acquistion of beat-to-beat pulse transit time (PTT) via piezoelectric/piezocapacitive sensors (PES/PCS) may expand perioperative hemodynamic monitoring. This study evaluated the ability for PTT via PES/PCS to correlate with systolic, diastolic, and mean invasive blood pressure (SBPIBP, DBPIBP, and MAPIBP) and to detect SBPIBP fluctuations. Methods: PES/PCS and IBP measurements were performed in 20 patients undergoing abdominal, urological, and cardiac surgery. A Pearson’s correlation analysis (r) between 1/PTT and IBP was performed. The predictive ability of 1/PTT with changes in SBPIBP was determined by area under the curve (reported as AUC, sensitivity, specificity). Results: Significant correlations between 1/PTT and SBPIBP were found for PES (r=0.64) and PCS (r=0.55) (p<0.01), as well as MAPIBP/DBPIBP for PES (r=0.6/0.55) and PCS (r=0.5/0.45) (p<0.05). A 7% decrease in 1/PTTPES predicted a 30% SBPIBP decrease(0.82, 0.76, 0.76), while a 5.6% increase predicted a 30% SBPIBP increase (0.75, 0.7, 0.68). A 6.6% decrease in 1/PTTPCS detected a 30% SBPIBP decrease (0.81, 0.72, 0.8), while a 4.8% 1/PTTPCS increase detected a 30% SBPIBP increase (0.73, 0.64, 0.68). Conclusions: Non-invasive beat-to-beat PTT via PES/PCS demonstrated significant correlations with IBP and detected significant changes in SBPIBP. Thus PES/PCS as a novel sensor technology may augment intraoperative hemodynamic monitoring during major surgery.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.