Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

As urban development increases in density, the space to grow urban trees becomes more constrained. In heavily developed areas, small stature trees can be planted to reduce both above- and below-ground conflicts with infrastructure elements. However, even these species have their limits when placed in extremely confining conditions. In this study, we build on past work to determine the minimum planting widths of small stature urban trees. We found that species, stem diameter, and the height at which stem diameter measurements occurred were all strong predictors of trunk flare diameter (adjusted R² of 0.843). Additionally, we modelled the relationship between planting space and the presence or absence of hardscape conflicts – using the predictions derived from this effort to project the potential cost savings in two United States cities. Study results provide a guideline to create sufficient space for urban trees and minimize infrastructure damage and associated cost savings.

Student-centered teaching practices such as active learning continue to gain momentum in college science education. Many instructors committed to these innovative practices transform their classroom beyond the standard lecture. Nevertheless, widespread implementation of these practices is limited because the learning benefits for students are often attained through increased instructional complexity to which many instructors cannot commit. When co-instructors are teaching the course, the level of commitment to building a student-centered classroom may be even more profound. For these reasons, new tools are needed to help instructors and co-instructors plan, organize, evaluate, and communicate their classroom innovations. Pathway modeling is a tool with potential to fill this gap. Unlike curriculum mapping -- which identifies academic content gaps, redundancies, and misalignments by examining a series of courses within a plan of study – course pathway modeling creates a visual map of a single course and reveals how teaching practices influence short-, mid-, and long-term student learning outcomes. This essay demonstrates how course pathway modeling can help co-instructors better represent the complexity of student-centered teaching practices. We include guides for creating course pathway models and discuss how this approach offers the potential to improve curricular design, course evaluation, student assessment, and communication between co-instructors.

Contact tracing is one of the oldest social network health interventions used to reduce the diffusion of various infectious diseases. However, some infectious diseases like COVID-19 amass at such a great scope that traditional methods of conducting contact tracing (e.g., face-to-face interviews) remain difficult to implement, pointing the need to develop reliable and valid survey approaches. The purpose of this research is to test the effectiveness of three different egocentric survey methods for extracting contact tracing data: (1) a baseline approach, (2) a retrieval cue approach, and (3) a context-based approach. A sample of 397 college students were randomized into one of each condition and were prompted to anonymously provide contacts and populated places visited from the past four days. After controlling for various demographic, social identity, psychological, and physiological variables, participants in the context-based condition were significantly more likely recall more contacts (medium effect size) and places (large effect size) than the other two conditions. Theoretically, the research supports suggestions by field theory that assume network recall can be significantly improved by activating relevant activity foci. Practically, the research contributes to developing innovative social network data collection methods for contract tracing survey instruments.

SARS-CoV-2 (severe acute respiratory syndrome coronavirus 2) is a novel virus of the family Coronaviridae. The virus causes the infectious disease COVID-19. The biology of coronaviruses has been studied for many years. However, bioinformatics tools designed explicitly for SARS-CoV-2 have only recently been developed as a rapid reaction to the need for fast detection, understanding, and treatment of COVID-19. To control the ongoing COVID-19 pandemic, it is of utmost importance to get insight into the evolution and pathogenesis of the virus. In this review, we cover bioinformatics workflows and tools for the routine detection of SARS-CoV-2 infection, the reliable analysis of sequencing data, the tracking of the COVID-19 pandemic and evaluation of containment measures, the study of coronavirus evolution, the discovery of potential drug targets and development of therapeutic strategies. For each tool, we briefly describe its use case and how it advances research specifically for SARS-CoV-2. All tools are freely available online, either through web applications or public code repositories.

The ability to read and quantify nucleic acids such as DNA and RNA using sequencing technologies has revolutionized our understanding of life. With the emergence of synthetic biology, these tools are now being put to work in new ways - enabling de novo biological design. Here, we show how sequencing is supporting the creation of a new wave of biological parts and systems, as well as providing the vast data sets needed for the machine learning of design rules for predictive bioengineering. However, we believe this is only the tip of the iceberg and end by providing an outlook on recent advances that will likely broaden the role of sequencing in synthetic biology and its deployment in real-world environments.

At the time of reception of this article (April 2, 2020), efforts to develop a specific vaccine against SARS-Cov-2, the causative agent of the coronavirus disease 2019 (COVID-19), had just begun trial phase 1, but full validation of this and other current developments is likely to take many more months to reach completion. The ongoing pandemic constitutes a major health burden of world proportions that is also having a devastating impact on whole economies worldwide, the knock-on effects of which could be catastrophic especially in poorer countries. Alternative measures to ameliorate the impact and hamper or minimally slow down disease progression are urgently called for. This review discusses past and currently evolving data on the etiological agent of the current pandemic, SARS-CoV-2, and its host cell receptors with a view to disclosing alternative drugs for palliative or therapeutic approaches. Firstly, SARS-CoV-2 exhibits marked tropism for cells that harbor the membrane-bound metalloprotease angiotensin-converting enzyme 2 (ACE2) at their plasmalemma, predominantly in cells lining the oral cavity, upper respiratory tract, and bronchoalveolar cells, making these epithelial mucosae the most likely viral receptor cell targets and entry routes. Secondly, the crystal structures of several coronavirus spike proteins in complex with their cell host target receptors, and of SARS-Cov-2 in complex with an inhibitor, are now available at atomic resolution through X-ray diffraction and cryo-electron microscopy studies. Thirdly, viral entry of other viruses has been successfully blocked by inhibiting viral endogenous proteases or clathrin/dynamin-dependent endocytosis, the same internalization pathway followed by ACE2 and some viruses. Fourthly, the target cell-surface receptor molecules and SARS-CoV-2 possess other putative sites for drugs potentially modulating receptor activity or virus processing. A multi-pronged pharmacological approach attacking more than one flank of the viral-receptor interactions is worth considering as a front-line strategy.

This paper investigates a range of popular differential evolution (DE) configurations to identify components responsible for emergence of structural bias – a recently identified tendency of algorithms to prefer some regions of search space over others, for reasons unrelated to objective function values. Previous work has explored this tendency for genetic algorithms (GA) and particle swarm optimisation (PSO), finding a relationship between population size and extent of structural bias, hence highlighting potential weaknesses of those algorithms. In current article, we focus on DE, extend the investigation to include consideration of an algorithmic component that is often overlooked – constraint handling mechanism. Towards this end, a wide range of DE configurations was tested here. Results suggest that DE is generally robust to structural bias. Unlike the case with GA and PSO, population size seems to have no influence on DE structural bias. Only one of variants studied – DE/current-to-best/1/bin – shows clear signs of bias, however, we show that this effect is mitigated by a judicious choice of constraint handling technique. These findings contribute towards explaining widespread success of DE variants in algorithm comparison studies; its robustness to structural bias represents the absence of a factor that may confound other algorithms.

A robust guaranteed cost preview repetitive controller is proposed for a class of polytopic uncertain discrete-time systems. In order to improve the tracking performance, the repetitive controller combined with preview compensator is inserted in the forward channel. By using the L-order forward difference operator, an augmented dynamic system is constructed. Then, the guaranteed cost preview repetitive control problem is transformed into the guaranteed cost control problem for the augmented dynamic system. For given performance index, the sufficient condition of asymptotic stability for the closed-loop system is derived by combining parameter-dependent Lyapunov function method with linear matrix inequality (LMI) techniques. By incorporating the controller obtained into the original system, the guaranteed-cost preview repetitive controller is derived. A numerical example is also included to show the effectiveness of the proposed method.

Molecular dynamics(MD) simulations are playing an increasingly important role in structure-based drug discovery (SBDD). Here we review the use of MD for proteins in aqueous solvation, organic/aqueous mixed solvents (MDmix) and with small ligands, to the classic SBDD problems: binding mode and binding free energy predictions. The simulation of proteins in their condensed state reveals the solvent structure and preferential interaction sites (hot spots) on the protein surface. This information is largely transferable across all classes of protein ligands (from water to drugs) and can be used very effectively to understand ligand recognition and improve the predictive capability of well-established methods such as molecular docking. MD simulations for protein and drug or drug-like compounds are now being used but are still computationally expensive and can only be applied to specific cases. On the other hand, MDmix simulations can now be used in SBDD and we will describe the latest developments and implementations. We expect to see an increase in the application of these techniques to a plethora of protein targets to identify new drug candidates with the advent of new tools and faster computers.

Colombia has initiated the process of participating in the environmental projects of the United Nations global agenda for the mitigation of climate change and the protection of biodiversity. Consequently, organizations within the solidarity sector have devised projects with the objective of aligning themselves with regional programs and of promoting leadership in the rural development through solidarity-based environmental initiatives. These include the organizations Canapro Ambiental, Cooperación Verde and Cootregua, which have participated in and accompanied local environmental projects. This study has identified the common elements related to the principles of organizational design proposed by Elinor Ostrom as a result of the adoption of Corporate Social Responsibility (CSR) for the purpose of a sustainable growth. The above findings serve to corroborate the relevance of the principles of organizational design as a qualitative assessment methodology for environmental solidarity initiatives. In particular, the methodology demonstrates the value of supporting the objectives of environmental sustainability and governance in the long term, by means of the strengthening of Corporate Social Responsibility (CSR) for the purposes of the solidarity ecosystem.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

Target detection of defense technology is being rapidly upgraded with modern surveillance technologies. The latest techniques of surveillance are already being implemented for defense applications. Self-protection and hiding from opposing forces are the key principle for protection of special team in defense. Camouflage textiles aims to create confusing objects for target detection of military personnel. These textiles are applied for military protection such as clothing, weapon, vehicle and location hiding nets/tents, etc. The urgent need of camouflage textiles have been formulated with a technical solution and implementation of right camouflage materials for concealment of defense target signature against dry leaves, green leaves, tree bark-woodland combat background; water-marine combat background; sand-desertland combat background; stone-stoneland combat background; snow-snowland combat background; sky combat background and ice-iceland combat background, concrete-concreteland combat background (DGTWSICB) in ultraviolet-visible-infrared (UV-Vis-IR) spectrums. This hypothesis of optical & surveillance engineering has been coalesced for advancement of UV-Vis-IR-DGTWSICB camouflage textiles technology. The principle of camouflage engineering has been approached by broader spectrum probe in UV-Vis-IR rather than Vis ranges only. Furthermore, single formulation of camouflage textiles has been proposed for multidimensional CBs-DGTWSICB. Electromagnetic spectrum, reflection, electron energy, photonic signal and imaging mechanism in UV-Vis-IR have been presented for optical engineering of concealment, detection, recognition and identification of target signature against DGTWSICB. Spectrum relationship of camouflage materials and DGTWSICB materials have been illustrated and compared in UV-Vis-IR spectrums. Camouflage material design, method design & spectral design; adaptive camouflage; techniques for camouflage textile assessment for digital camera and hyperspectral camera imaging; image processing techniques and a hierarchical model have been demonstrated for augmentation of camouflage textiles in UV-Vis-IR illumination. Therefore, anticipated design of camouflage textiles may enhance high-performance innovation for modern surveillance of military protection related to digital camera, hyperspectral camera and radar. This hypothesis includes advance guideline for camouflage textiles design for CBs-DGTWSICB.

Vernacular architecture constitutes a rich source of information and ancestral knowledge that can become a key resource for sustainable development through its passive design strategies, which effectively respond to local climatic and weather conditions using locally sourced materials for the construction of its supporting structure and enveloping elements, as well as spatial organization and the incorporation of a buffer area (patio) that optimize the use of renewable resources. This qualitative study analyzes a traditional housing typology with a central patio located in the Historic Center of Azogues city, Ecuador, to evaluate its interior thermal comfort through in-situ monitoring in the different building spaces. Using the open-source software Open Studio and EnergyPlus, a simulation model was built to assess the annual thermal performance of the house. Field records were used to verify the effectiveness of the strategies that respond to the climatic conditions of the area. The analysis carried out on the passive strategies used in the selected house with regard to natural ventilation, solar protection, and thermal insulation, which depend on various aspects of the building, such as its location, internal space arrangement, design of openings (doors and windows), among others. The thermal simulations reveal that the traditional house located in the Historic Center of Azogues city is well adapted to the local climate, although interior thermal comfort is not entirely satisfactory.

Coaxial rotors can be found in multirotor vehicles for the added thrust compared to independent rotors while keeping similar area footprints but, performance losses should be considered. This experimental study analyzes the effects of varying motor throttle and propeller pitch values in motor-propeller systems with two to four coaxial rotors. The results show that in a two-rotor coaxial system, to lessen the adverse effects of a front rotor’s backwash and to operate at the maximum performance, only the back motor should be operated initially up to 75% duty cycle before using the front motor up to its 75% duty cycle. Additional thrust requirements should be generated from the back rotor and then from the front rotor up to their maximum duty cycles. In two, three, and four-rotor coaxial setups, total thrust output generated is 1.6, 2.1, and 2.5 times the thrust output at system thrust performance of 86%, 76%, and 66%, respectively of that of an isolated rotor. In a four-rotor coaxial setup, maximum system performance is achieved when the propeller pitch values are gradually increased from the first to the last rotor. The gradual increments in propeller pitch values also result in more uniform thrust sharing among rotors.

Fossil fuels and carbon origin resources are affecting our environment. Therefore, alternative energy sources have to be established to co-produce energy along with fossil fuels and carbon origin resources until it is the right time to replace them. Microbial Fuel Cell (MFC) is a promising technology in the field of energy production. Compared to the conventional power sources it is more efficient and not controlled by the Carnot cycle. Its high efficiencies, low noise, and less pollutant output could make it revolutionize in the power generation industry with a shift from centrally located generating stations and long-distance transmission lines to dispersed power generation at load sites. In this review, several characteristics of the MFC technology will be highlighted. First, a brief history of abiotic to biological fuel cells and subsequently, microbial fuel cells is presented. Second, the focus is then shifted to elements responsible for the making MFC working with efficiency. Setup of the MFC system for every element and their assembly is then introduced, followed by an explanation of the working machinery principle. Finally, microbial fuel cell designs and types of main configurations used are presented along with scalability of the technology for the proper application.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

Macrolide antibiotics, effective antimicrobial agents, are intensively used in human and veterinary medicine as well as in agriculture and therefore are found all over the world as environmental pollutants, harming sensitive eco-community organisms and provoking the selection of resistant forms. A novel azithromycin derivative was synthesized and as a rationally designed hapten conjugate ensured group immunorecognition of 6 major macrolide representatives (105-41%), erythromycin, erythromycin ethylsuccinate, clarithromycin, roxithromycin, azithromycin and dirithromycin in competitive immunoassay based on anti-clarithromycin antibodies. The heterologous hapten-based ELISA format simultaneously contributed to a 5-fold increase in sensitivity (ERY IC50 = 0.04 ng/mL). However, for the detection of trace macrolides in environmental samples, an underexploited in immunoassay field strategy was proposed in the present study to significantly improve the detectability of analytes. Unlike most approaches, it does not require special enhancers/amplifiers or additional concentration/extraction procedures, but only involves a larger volume of test samples. Gradual volume increase of samples (from 0.025 to 10 mL) analyzed in direct competitive ELISA, immunobeads, and immunofiltration assay formats based on the same reagents resulted in a significant improvement (more than 50-fold) in assay sensitivity and detection limit up to 5 and 1 pg/mL, respectively. The suitability of the test for detecting macrolide contamination of natural water was confirmed by recovery of macrolides from spiked blank samples (71.7-141.3%). A series of natural water samples from Lake Onega and its influents near Petrozavodsk were analyzed during a 2022-2023 using both the developed immunoassay and HPLC-MS/MS and revealed no macrolide antibiotic contamination.

This study presents structural analysis and optimization for the lightweight design of a buoyant rotor-type permanent magnet (BRPM) generator, which was first presented in Bang (2010), and compares its structural performances to a conventional generator with a spoke arm-type rotor and stator. The main benefit of a BRPM is that it can be realized as a bearing-less drive system, free from the mechanical failure of rotor bearings, by using a buoyant rotor. Also, the deformation of a generator by blade vibration can be effectively suppressed using joint couplings between the blades and the rotor. For the design optimization, the objective is set as the mass of the rotor and the stator, and the maximum deformation of the airgap clearance between the rotor and the stator by external forces is constrained below 10% of the gap width. The commercial software Optistruct is used for the analysis and optimization. In this investigation, the analysis and optimization are conducted for a 10 MW wind turbine generator. However, the proposed methods can be extended to larger generator designs without requiring considerable modification. The mass of the opti-mized 10MW BRPM generator is 160.7 tons (19.3 tons for the rotor and 141.4 tons for the stator) while that of an optimized conventional spoke arm-type generator is obtained as 325.6 tons.

Public transport systems are considered to be a crucial aspect of a sustainable urban development, as they allow more passengers to efficiently travel across an urban area at low environmental and economic costs. Multiple factors can influence the public transport level of service. All take roots in the network structure and the operating regime, i.e. how bus lines are arranged atop the street network and how the service frequency is adjusted to meet urban mobility patterns. This is known as the bus network design problem and has been the subject of several studies. The problem is so challenging that most studies until now resort to strong assumptions such as a static description of the peak hour demand, homogeneous user behavior, and equal trip lengths. Potential effects of different types of user behavior and trip lengths patterns on the user and/or operator cost function have not been investigated whatsoever. Moreover, the existing studies have not considered the effects of the bus network structure on private car users, the level of interactions between the two modes, and the passenger mode choice that depends on the traffic conditions. This paper aims to close this gap and provide a general framework considering multiple trip length patterns, two types of user behavior, and the effects that the bus network structure might have on the traffic performance and passenger mode choice. For modeling different trip length patterns, the proposed approach combines all origin-destination pairs with the same trip length and uses the trip length distribution as an intermediate level of abstraction. As such, it allows to solve the optimal bus network design problem in an analytical way, while considering a more realistic setting including network congestion, mixed traffic, and different mode choice decisions depending on trip lengths and walking preferences. Numerical analysis reveals that both, the user behavior and the trip length patterns, have significant effects on the operator and user cost function. Results show that the probability of choosing any given mode is not constant across the user trip lengths, but follows certain distribution. This distribution is not unique, but varies across the trip length patterns, indicating the importance of modeling the mode choice at the trip length level. Finally, the analysis demonstrates the significance of addressing simplifications made in previous studies.

The article presents a hybrid method for calculating the chemical composition of steel with the required hardness after cooling from the austenitizing temperature. Artificial neural networks and genetic algorithms were used to develop the model. Based on 550 diagrams of continuous cooling transformation (CCT) of structural steels available in the literature, a dataset of experimental data was created. Artificial neural networks were used to develop a hardness model describing the relationship between the chemical composition of the steel, the austenitizing temperature, and the hardness of the steel after cooling. A genetic algorithm was used to identify the chemical composition of the steel with the required hardness. The value of the objective function was calculated using the neural network model. The developed method for identifying the chemical composition was implemented in a computer application. Examples of calculations of mass concentrations of steel elements with the required hardness after cooling from the austenitizing temperature are presented. The model proposed in this study can be a valuable tool to support chemical composition design by reducing the number of experiments and minimizing research costs.

Machining titanium alloy (Ti6Al4V) used in orthopedic implants by conventional metal cutting processes is challenging due to excessive cutting forces, low surface integrity and tool wear. To overcome these difficulties and for ensuring high-quality products, various industries employ wire electrical discharge machining (WEDM) for precise machining of intricate shapes in titanium alloy. The objective is to make WEDM machining parameters as efficient as possible for machining the bio-compatible alloy Ti6Al4V using box-behnken design (BBD) and Non-dominated Sorting Genetic Algorithm II (NSGA II). A quadratic mathematical model is created to represent the productivity and the quality factor (MRR and surface roughness) in terms of varying input parameters, such as pulse active (Ton) time, pulse inactive (Toff) time, peak amplitude (A) current and applied servo (V) voltage. The established regression models and related prediction plots provide a reliable approach for predicting how the process variables affect the two responses viz MRR and SR. The effects of four process variables on both the responses were examined, and the findings revealed that the pulse duration and voltage has a major influence on the rate at which material is removed (MRR) whereas pulse duration influence quality (SR).  The trade-off between MRR and SR, when significant process factors are included emphasizes the need for a reliable multi-objective optimization method. The intelligent metaheuristic optimization method named non-dominated sorting genetic algorithm II (NSGA II) is utilized to provide pareto optimum solutions in order to achieve high material removal rate (MRR) and low surface roughness (SR).

The construction industry is one of the most fatal industries, so it is important to pay more attention to safety solutions. Even though work-related accidents are known as major waste in construction projects, little attention has been paid so far to incorporating safety into the lean construction framework. In this research, lean construction theory is reviewed through the lens of safety. That being so, the identified challenges in previous research on improving safety in construction projects are categorized and those related to the concept of lean project delivery are introduced. Then, the principles of the lean construction framework are explained and the relevant changes for incorporating safety into the framework are introduced and discussed. It is expected that this hybrid model would further enrich the lean construction framework. The careful attention of project executives to this model may improve the safety situation in construction projects.

Ucuùba fat is fat obtained from a plant found in South America, mainly in Amazonian Brazil. Due to its biocompatibility and bioactivity, the Ucuùba fat was used for production of ketoconazole-loaded nanostructured lipid carriers (NLC) in view of an application for the treatment of onychomycosis and other persistent fungal infections. The development and optimization of the Ucuùba fat based NLC were performed using a Box-Behnken design of experiment. The independent variables were surfactant concentration (% w/v), liquid lipids concentration (% w/v), solid lipids concentration (% w/v), while the outputs of interest were particle size, polydispersity index (PDI) and drug encapsulation efficiency (EE). The Ucuùba fat based NLC were produced and the process optimized determining a predictive mathematical model. Applying the model, two formulations with the pre-required particle size, i.e., 30 and 85 nm, were produced for further evaluation. The optimized formulations were characterized and showed a particle size in agreement to the predicted value, i.e. 33.6 nm and 74.6 nm, respectively. The optimized formulations were also characterized using multiple techniques in order to investigate the solid state of drug and excipients (DSC and XRD), particle morphology (TEM) and interactions between the formulation components (FTIR). Furthermore, particle size and surface charge of the formulations was studied during a one-month stability study and did not evidence any significative modification during storage.

The consistently positive Australian economic environment and stable population increase have led to a higher demand for new houses in recent years. Prefabrication is a promising method to help alleviate the issues related to housing shortage and affordability due to reduced material wastage, construction delays due to weather conditions, unexpected costs, shortage in labour and onsite risks. With the advancements in automation and manufacturing methods such as Design for Manufacturing and Assembly (DfMA), the quality and precision of prefabricated materials is tightly controlled, and the fabrication and assembly period are reduced. However, the full potential of prefabricated construction is yet to be realised in part due to most of developments being focused on its superstructure. A review of the current available options suitable for houses is necessary to understand the present state of the residential footing industry, which will help evaluate the necessary innovations for the growth of the Australian construction industry considering the local reactive soil conditions. This paper presents a summary of existing footing systems and potential prefabricated footing solutions for low-rise residential structures with one storey to two storeys. This paper also reviews the benefits and challenges of designing, manufacturing, transporting, handling and installing of prefabricated footings on site, which have great influence on the acceptance of these innovative footing systems.

The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

Silybum marianum (L.) Gaertn. (aka milk thistle) constitute the almost exclusive source of silymarin, a mixture of different flavonolignans, and is thus considered as a unique model for their extraction. The present research deals with ultrasound-assisted extraction (UAE) of S. marianum flavonolignans and their quantification using LC system. The optimal conditions for UAE were: aqueous EtOH 54.5% (v/v) as solvent, applying an ultrasound frequency of 36.6 kHz during an extraction time of 60 min at 45°C with a liquid to solid ratio of 25:1 ml/g DW. Following optimization, the extraction method was validated according to international standards of the association of analytical communities (AOAC) in order to ensure its precision and accuracy for the quantitation of the individual silymarin components. The efficiency of UAE was compared with maceration protocol of the same duration. The optimized and validated conditions allowed highest extraction yields of flavonolignans in comparison to maceration. The antioxidant capacity of the extracts was confirmed by the CUPRAC assays and inhibition of advanced glycation end products. The skin anti-aging action was also confirmed toward the strong in vitro inhibition capacity of the obtained extract against collagenase and elastase enzymes. The procedure presented here allows a green efficient extraction and quantification of the main flavonolignans from the fruits of S. marianum with attractive antioxidant and anti-aging activities for future cosmetic applications.

Motivation: there is a paradox at the heart of informatics where practical implementation generally fails to understand the socio-technical impact of novel technologies and disruptive innovation when adopted in `real-world’ systems. This phenomenon, termed technological determinism, is manifested in a time-lag between the adoption of novel technologies and an understanding of the underlying theory which develops following research into their adoption. Methods: we consider informatics theory as it relates to: social informatics and how humans’ function in society, the relationship between society and technology, information systems, information systems design, and human-computer interactions. The challenges posed by novel technologies and disruptive innovation are considered as they relate to information systems and information systems design. Open research questions with directions for future research are discussed with an introduction to and our proposed approach to socio-technical information system design. Significance: we conclude that the adoption of disruptive innovation presents both opportunities and threats for all stakeholders in computerised systems. However, determinism is a topic requiring research to generate a suitable level of understanding and technological determinism remains a significant challenge.

This paper proposes a parameter coordination optimization design of Power System Stabilizer (PSS) based on an improved Quasi-Affine Transformation Evolutionary (QUATRE) algorithm to suppress low-frequency oscillation and improve the dynamic stability of power system. To begin, the Simulated Annealing (SA) algorithm randomly updates the globally optimal solution of each QUATRE iteration and matches the inferior solution with a certain probability to escape the local extreme point. This new algorithm is first applied to power system. Second, Since damping ratio is one of the criteria to measure the dynamic stability of power system, this paper sets the objective function according to the principle of maximization of damping coefficient of electromechanical mode, and uses SA-QUATRE to search a group of global optimal PSS parameter combinations to improve the stability margin of the system as much as possible. Finally, the method's rationality and validity were validated by applying it to the simulation examples of IEEE 4-machine 2-area system with different operation states. The comparison with the traditional optimization algorithm shows that the proposed method has more advantages for multi-machine PSS parameter coordination optimization, and can restrain the low-frequency oscillation of power system more effectively and enhance the system stability.

In this paper, a new design of a helium-assisted hybrid drone is proposed for flight time enhancement. As is widely known, most of the drones with a VTOL (vertical take-off and landing) feature have a short operation time, limiting their capability to carry out sustainable operations for the given missions. Thus, with the clear goal of enhancing the flight time, this study aims to develop a hybrid drone system, where a helium balloon is used to provide a lifting force for this purpose. The proposed design for the hybrid drone has several benefits including easiness to manufacture and relatively small size when compared to other types of hybrid drones. Various analyses are conducted for the design of the hybrid drone system including the balloon shape and size, buoyant force, flight time, and connector design. Since stability and performance are one of the most important issues for the new design, the pole location analysis is conducted based on the control theory. This rigorous analysis provides that the proposed hybrid drone design is stable as well as robust against swinging motions. To validate the effectiveness of the proposed design and flight time enhancement, simulations were conducted and experimental results are also provided using the manufactured hybrid drone system. Through the real experiments, it is proved that the hybrid drone can increase the flight time more than 2.5 times while guaranteeing stable motions.

The present work presents and discusses an analysis of the floor types of Villa of Diomedes (Pompeii archaeological park in the Campania region, Italy) both from architectural, archaeological, and structural point of view. In particular, the geometrical structural parameters of different floor types and the rules used by ancient builders to design them are investigated by means of interdisciplinary research. Link between structural-based assumptions, archival sources, geometric survey, in situ visual inspections and the archaeological information make it possible to define the geometrical structural parameters of eleven-barrel vaults, three wooden floors and three sloped wooden roofs (buried and collapsed during the Vesuvius eruption). A specific study of the barrel vaults is presented to investigate the relationships between the main vaults’ structural parameter. Furthermore, a comparison between the vaults’ dimensions obtained from surveys and those produced by the literature formulations from the 15th to the 20th centuries concerning masonry-vault designs is presented and discussed. These analyses carried out in the framework of Villa of Diomedes interdisciplinary project was very useful to interpret the fabrication of the Villa and to make a reconstruction of 3D model as it probably resulted to be the fateful year of 79 A.D.

Three ternary mixtures composed by choline chloride (ChCl), ethylene glycol (EG) and a second hydrogen bond donor (HBD) as ethanol (A), 2-propanol (B), and glycerol (C) were studied in terms of composition related to the band gap energy (BGE). A Design of Experiments (DoE) approach, and in particular a Simple Lattice three-components design, was employed for determining the variation of the BGE upon the composition of each system. UV-VIS analysis and subsequent Tauc plot methodology provided the data requested from the DoE and multivariate statistical analysis revealed a drop of the BGE in correspondence to specific binary compositions for systems A and B. In particular, a BGE of 3.85 eV was registered for the mixtures ChCl/EtOH (1:1), and ChCl/2-propanol (1:1), which represents one of the lowest values ever observed for these systems.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Phthalate esters (PAEs) are a ubiquitous kind of environmental endocrine-disrupting chemicals, causing environmental and health issues. EstJ6 is an effective phthalate-degrading hydrolase, and its mutant with a combination of three non-conservative distal mutations has an improved activity against PAEs with unknown molecular mechanisms. Herein, we attempt to fill the significant gap between distal mutations and the activity of this enzyme using computational approaches. We find mutations result in a redistribution of enzyme’s preexisting conformational states and dynamics changes of key functional regions, especially the lid over the active site. The outward motion of the lid upon mutations should make it easier for substrates or products to enter or exit. Additionally, the stronger substrate binding affinity and conformational rearrangements of catalytic reaction-associated residues in mutant, accompanied by the strengthened communication within the protein, might contribute to the elevated catalytic efficiency. Finally, an attempt has been done to improve the thermostability of EstJ6 upon introducing a distal disulfide bond between residues A23 and A29, and the simulation results are as expected. Together, our work explored the allosteric effects caused by distal mutations, which could provide insights into the rational design of esterases for industrial applications in the future.

Open-plan office (OPO) layouts emerged to allow organizations to adapt to changing workplace demands. We explore the potential for OPOs to provide such adaptive capacity to respond to two contemporary issues for organizations: the chronic challenge of environmental sustainability, and the acute challenges emerging from the great COVID-19 homeworking experiment. We apply a socio-technical systems perspective and green ergonomics principles to investigate the relationship between an OPO environment and the occupants working within it. In doing so, we consider the relevant technical and human factors such as green technology and employee green behavior. We also consider how a green OPO might provide non-carbon benefits such as improving occupant wellbeing and supporting the emergence of a green organizational culture. Our investigation highlights several avenues through which an OPO designed with green ergonomic principles could benefit occupants, the organizations they work for, and the natural environment of which they are a part and on which they depend. We find reason to suspect that green OPOs could play an important role in sustainable development; and offer a research agenda to help determine whether in fact OPOs are another example of how going green is good business.

In bioprocess development, the host and the genetic construct for a new biomanufacturing process are selected in the early developmental stages. This decision, made at the screening scale with very limited information about the performance of the selected cell factory in larger reactors, has a major influence on the performance of the final process. To overcome this, scaledown approaches are essential to run screenings that show the real cell factory performance at industrial like conditions. We present a fully automated robotic facility with 24 parallel mini-bioreactors that is operated by a model based adaptive input design framework for the characterization of clone libraries under scale-down conditions. The cultivation operation strategies are computed and continuously refined based on a macro-kinetic growth model that is continuously re-fitted to the available experimental data. The added value of the approach is demonstrated with 24 parallel fed-batch cultivations in a mini-bioreactor system with eight different Escherichia coli strains in triplicate. The 24 fed-batches ran under the desired conditions generating sufficient information to define the fastest growing strain in an environment with varying glucose concentrations similar to industrial scale bioreactors.

The worldwide outbreak of a novel coronavirus, SARS-CoV-2 has caused a pandemic of respiratory disease. Due to this emergency, researchers around the globe have been investigating the evolution of the genome of SARS-CoV-2 in order to design vaccines. Here I examined the evolution of GC content of SARS-CoV-2 by comparing the genomes of the members of the group Betacoronavirus. The results of this investigation revealed a highly significant positive correlation between the GC contents of betacoronaviruses and their divergence from SARS-CoV-2. The betacoronaviruses that are distantly related to SARS-CoV-2 have much higher GC contents than the latter. Conversely, the closely related ones have low GC contents, which are only slightly higher than that of SARS-CoV-2. This suggests a systematic reduction in the GC content in the SARS-CoV-2 lineage over time. The declining trend in this lineage predicts a much-reduced GC content in the coronaviruses that will descend/evolve from SARS-CoV-2 in the future. Due to the three consecutive outbreaks (MERS-CoV, SARS-CoV and SARS-CoV-2) caused by the members of the SARS-CoV-2, the scientific community is emphasizing the need for universal vaccines that are effective across many strains including those, that will inevitably emerge in the near future. The reduction in GC contents implies an increase in the rate of GC→AT mutations than that the mutational changes in the reverse direction. Therefore, understanding the evolution of base composition and mutational patterns of SARS-CoV-2 could be useful in designing broad-spectrum vaccines that could identify and neutralize the present and future strains of this virus.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Material selection for product design is a complex task. Thus, one of the objectives of this work is to analyze, understand and promote the importance of selection of materials to conceive quality products with help of designers' that promote green self-identity in the early stage of the conception of new products. A questionnaire was sent to professional designers and engineers. 38 responses were validated, this being the sample of our study. The aspects that influence the complex selection of materials and the final quality of the products through the design and production process is presented. As a result of the answers carried out with product designers who work in the market, with students who are graduating and with some engineers, a new approach for the selection of materials was developed. Based on a collection of main ideas from traditional and non-traditional methods of material selection, seeking to group the maximum requirements of both methods, inspired by the "Canvas" model on the basic modular methodology, a new model for a project of new product is presented. Our study focuses on the selection of materials, since this aspect is one of the most relevant steps in early stage of the prototyping phase of new products, with a view to reducing CO² from the air in the atmosphere that we all breathe. The classification of materials is complex, due to the diversity of available options. The novelty of this model is that all properties of the newly designed product, such as technical, aesthetic, productive, environmental and other properties, are all grouped in a model, which serves as an innovative support. Thus, the designer has at his disposal a tool that can help him in the selection of the best material for the products he designs. This study intends to make a contribution in the field of material selection, quality and design of new products, promoting a green self-identity for designers in the initial phase of product design. Consequently, all consumers in search of a sustainable planet will profit from it.

Wearable antennas are increasingly vital in modern healthcare, facilitating continuous monitoring and communication for medical purposes. These antennas are integrated into wearable devices, allowing for the transmission and reception of vital health data, such as heart rate, body temperature, and blood pressure, to medical professionals or monitoring systems in real time. This instantaneous data transmission enables timely interventions, thus improving the quality of healthcare services. This review aims to comprehensively synthesize recent research from reputable databases, focusing on the functionality and effectiveness of wearable antennas in medical applications. The primary objectives of each study were categorized, including antenna design and integration, the performance of medical wearable antenna technology, safety considerations in wearable antenna biomedicine, and the use of antennas in clinical applications and their impact. This synthesis provides valuable insights for researchers and practitioners aiming to develop and deploy wearable antennas in medical settings, ultimately enhancing healthcare delivery and patient outcomes.

Lumbar support exoskeletons with active and passive actuators are currently the cutting-edge technology for preventing back injuries in workers while lifting heavy objects. However, many challenges still exist in both types of exoskeletons, including rigid actuators, risks of human-robot interaction, high battery consumption, bulky design, and limited assistance. In this paper, the design of a compact, lightweight energy storage device combined with rotary series elastic (ES-RSEA) is proposed for use in a lumbar support exoskeleton to increase the level of assistance and exploit the human bioenergy during the two stages of the lifting task. ES takes the responsibility to store and release passive mechanical energy while RSEA provides excellent compliance and prevents injury from the human body's undesired movement. The experimental tests on the spiral spring showed excellent linear characteristics (above 99%) with an actual spring stiffness of 9.96 Nm/rad. The results demonstrate that ES-RSEA can provide maximum torque assistance in the ascent phase with 66.6 Nm while generating nearly 21 Nm of spring torque during descent without turning on the DC motor. Ultimately, the proposed design can maximize the energy storage of human energy, exploit the biomechanics of lifting tasks, and reduce the burden on human effort to perform lifting tasks.

Extreme value analysis (EVA) is well-established to derive hydrometeorological design values for infrastructure that has to withstand extreme events. Since there is evidence of increased extremes with higher hazard potential under climate change, alterations of EVA are introduced for which statistical properties are no longer assumed to be constant but vary over time. In this study, both stationary and non-stationary EVA models are used to derive design life levels (DLLs) of daily precipitation in the pre-alpine Oberland region of Southern Germany, an orographically complex region characterized by heavy precipitation events and climate change. As EVA is fraught with uncertainties, it is crucial to quantify its methodological impacts: two theoretical distributions (i.e., Generalized Extreme Value (GEV) and Generalized Pareto (GP) distribution), four different parameter estimation techniques, (i.e., Maximum Likelihood Estimation (MLE), L-moments, Generalized Maximum Likelihood Estimation (GMLE), and Bayesian estimation method) are compared. Discrepancies due to the parameter estimation methods may reach up to 45 % of the mean absolute value, while differences between stationary and non-stationary models are of the same magnitude (differences in design levels up to 40%). Despite the underlying large methodological uncertainties, there is a robust tendency for increased DLLs in the Oberland region towards the end of this century based on the (non-)stationary models.

Process induced defects during thermoforming are widespread problems in laminate manufacturing. The aim of this study is to describe the effects of holding time and pressure on several properties of the manufactured laminate. A design of experiments is performed, followed by an analysis of variance to examine significant effects. Subsequently, a regression model is created to predict the laminate’s properties, which is also validated. The highest values of tensile strength and elongation at break are found for low settings of holding time and pressure. The fibre volume fraction is not affected by the process parameters. As holding time and pressure increase, significant fibre misalignment takes place, leading to a decrease of the mechanical properties. The regression model corresponds well with the validation and should be extended with further variables in subsequent studies.

Methods for cost calculation of Laser-based Additive Manufacturing (LAM) have evolved over the last two decades. Starting from a rapid prototyping manufacturing method, cost calculation over time included more than single part production for small series or mixed batches. New machine developments nowadays aim at large scale production and introduce modular machine designs that give LAM factory operators more decision freedom on machine configurations and expansibility. To leverage this new possibilities, LAM costing methods must be adapted to calculate and visualize the economic consequences of different module configurations.In this work a modelling architecture of L-PBF machines using virtual modules is presented. Using principles of the industry 4.0 communication standard OPC UA, a virtual machine is set up, parametrized and connected to the AM digital process chain. Two different views on the cost information are used, optimized for different use cases.First, the product view allows detailed analysis of cost allocation to parts in mixed batches and the layered geometry of the part. Second, the machine view tracks utilization of all machine modules, divided into the states idle, active, off and maintenance. The theoretical Overall Equipment Effectiveness (OEE) is calculated on a module basis, enabling economic analysis and optimization of module composition as well as module improvements and new modular machine constellations. This allows focusing research and development on most valuable improvements. By calculating different scenarios like spare part production, mass production or rapid prototyping, the part portfolio to be manufactured can be considered.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

Favipiravir is a broad-spectrum inhibitor of viral RNA-dependent RNA polymerase (RdRp) currently being used to manage COVID-19 in several countries. By acting as a substrate for RdRp, favipiravir gets incorporated into the nascent viral RNA and prevents strand extension. A high mutation rate of SARS-CoV-2 RdRp may facilitate antigenic drift as an answer to the host immune response, thereby generating resistance of virus to favipiravir. Therefore, it is extremely crucial to predict potential mutational sites in the RdRp and the emergence of structural modifications contributing to drug resistance. Here, we used high-throughput interface-based protein design to generate >100,000 designs and identify mutation hotspot residues in the favipiravir-binding site of RdRp. Several mutants had lower binding affinities to favipiravir, out of which hotspot residues with a high propensity to undergo positive selection were identified. The results showed that the designs retained an average of 97 to 98% sequence identity, suggesting that SARS-CoV-2 can develop favipiravir resistance with just a few mutations. Notably, we observed that out of 134 mutations predicted designs, 63 specific mutations were already present in the CoV-GLUE database, thus attaining ~47% correlation match with the clinical sequencing data. The findings improve our understanding of the potential signatures of adaptation in SARS-CoV-2 against favipiravir and management of COVID-19. Furthermore, they can help develop exhaustive strategies for robust antiviral design and discovery.

Dysregulation of the Cyclin-dependent kinase 8 (CDK8) activity has been associated to many diseases including the colorectal and breast cancer. As usual in the CDK family, the activity of CDK8 is controlled by a regulatory protein called cyclin C (CycC). But while human CDK family members are generally activated in two steps that is, the binding of the cyclin to CDK and the phosphorylation of a residue in the CDK activation loop, CDK8 does not require the phosphorylation step to be active. Another peculiarity of CDK8 is its ability to be associated to CycC while adopted an inactive form. These specificities raise the question of the role of CycC in the complex CDK8-CycC, which appears to be more complex than for the other members of CDK family. Through MD simulations and binding free energy calculations, we investigated the effect of CycC on the structure and dynamics of CDK8 on the one hand, and the structural molecular basis of the protein-protein interaction between the two partners on the other hand. We found that CycC has a stabilizing effect on CDK8 and identified specific interaction hotspots within its interaction surface compared to other human CDK/Cyc pairs. Targeting these specific interaction hotspots could be a promising approach in terms of specificity, to effectively disrupt the interaction between CDK8. The simulation of the conformational transition from the inactive to the active form of CDK8 suggests that the residue Glu99 of the CycC may assume the role of the missing phosphorylation step in the activation mechanism of CDK8. In a more general view, these results point the importance of keeping the CycC in computational studies when studying the human CDK8 protein in both the active and the inactive form.

Philips Visual Patient Avatar represents an alternative method of patient monitoring that, according to computer-based simulation studies, enhances diagnostic accuracy, confidence and reduces workload. After its clinical integration, we assessed pediatric anesthesia providers' perspectives on this technology. This is a single-center qualitative study, conducted at the University Hospital Zurich using in-depth individual interviews. We aimed to identify the advantages and limitations of Visual Patient Avatar in pediatric anesthesia and to assess children and parents' reactions from caregivers' perspective. Thematic analysis was used to identify the dominant themes. Fourteen members of the institution's pediatric anesthesia team were interviewed. The most prevalent themes were: children's positive reactions towards the Visual Patient Avatar (92.9%) and enhanced speed in problem identification (71.4%). Additionally, 50% of participants reported finding the Visual Patient Avatar useful for diverting children's attention during anesthesia induction, and 50% suggested that its vital sign thresholds should be adaptable for different age groups. The study revealed that the Visual Patient Avatar was recognized as a valuable tool in pediatric anesthesia, enabling prompt identification of underlying issues and receiving positive feedback from both children and parents. The most commonly voiced wish for improvement in the study was the ability to customize the Visual Patient Avatar's thresholds for different age groups.

Exoskeleton robots are a rising technology in industrial contexts to assist humans in onerous applications. Mechanical and control design solutions are intensively investigated to achieve a high performance human-robot collaboration (e.g., transparency, ergonomics, safety, etc.). However, the most of the investigated solutions involve high-cost hardware, complex design solutions and standard actuation. In the presented work, an industrial exoskeleton for lifting and transportation of heavy parts is proposed. A low-cost mechanical design solution is proposed, exploiting compliant actuation at the shoulder joint to increase safety and transparency in human-robot cooperation. A hierarchic model-based controller is then proposed (including the modeling of the compliant actuator) to actively assist the human while executing the task. An inner optimal controller is proposed for trajectory tracking, while an outer fuzzy logic controller is proposed to online deform the task trajectory on the basis of the human’s intention of motion. A gain scheduler is also designed to calculate the optimal control gains on the basis of the performed trajectory. Simulations have been performed in order to validate the performance of the proposed device, showing promising results. The prototype is under realization.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

Temporary pavilions play an important role as experimental fields for architects, designers and engineers, apart from providing exhibition spaces. Novel structural and formal solutions applied in pavilions also can give them unusual appearance that attracts eyesight of spectators. In this article authors explore the possibility of combination of structural novelty, visual attractiveness and low-cost by a design and construction of a temporary pavilion. For that purpose, an innovative structural system and design approach was applied, i.e. membrane structure designed in Rhino and Grasshopper environments with the use of Kiwi!3D IsoGeometric analysis tool. The designed pavilion, named Obverse/Reverse, was built in Opole, Poland, for the occasion of World Architecture Day in July 2019. Design and construction was performed by the authors in cooperation with students’ organisation Humanisation of Urban Environment from the Faculty of Architecture Wroclaw University of Science and Technology. The Rresultant pavilion proved the possibility of obtaining a low-budgets but visually attractive architectural solution with the adaption of parametrical design tools and some scientific background with innovative structural systems.

Visual Patient Avatar ICU is an innovative approach to patient monitoring enhancing the user's situation awareness in intensive care settings. It dynamically displays the patient's current vital signs through changes in color, shape and animation. The technology can also indicate patient-inserted devices, such as arterial lines, central lines and urinary catheters, along with their insertion locations. We conducted an international, multi-center study using a sequential qualitative-quantitative design to evaluate users' perception of Visual Patient Avatar ICU among physicians and nurses. Twenty-five nurses and twenty-five physicians from the ICU participated in the structured interviews. Forty of them completed the online survey. Overall, ICU professionals expressed a positive outlook on Visual Patient Avatar ICU. They described Visual Patient Avatar ICU as a simple and intuitive tool that improved information retention and facilitated problem identification. However, a subset of participants expressed concerns about potential information overload and a sense of incompleteness due to missing exact numerical values. These findings provide valuable insights into user perceptions of Visual Patient Avatar ICU and encourage further technology development before clinical implementation.

Abstract: Intensity of natural and man-made disasters is increasing day by day. Disaster is one of the major threats that affects the sustainable development of tourist attractions. Big data and Internet of Things(IoT) will greatly improve the disaster management. Based on the Big Data and IoT, a tourism attraction disaster management system is designed, divided into several stages namely pre-disaster early warning prevention, disaster mitigation, recovery and reconstruction after disaster and updating disaster planning. Then, the system flow is analysed, as well as the system structure is constructed. Additional, system function and its operation flow are introduced, including disaster warning, disaster relief, disaster assessment, real-time monitoring and supporting disaster planning functions. Finally, an application case is introduced. Research intends to improve tourism area disasters management.

The last decade has witnessed rapid development of immersive virtual reality (IVR) and its application in various contexts. However, its application in supporting real-time virtual collaboration has been quite rare due to technical barriers and the lack of validated design principles. To address this research gap, this study designed and developed an IVR space to enable multi-user synchronous co-located collaboration. An evaluation study (N = 95) was conducted to explore its useful design considerations and the influencing factors for collaboration experience. The IVR space was enabled by the simultaneous localization and mapping (SLAM)-based inside-out tracking technique and was informed by four essential design considerations for promoting effective collaboration in IVR, namely, the role script, learning task, collaboration mechanism, and communication design. The study results revealed that students in general were satisfied with their collaboration experience in IVR, with social presence and collaboration competency as significant predictors of collective efficacy and social experience. Based on both quantitative and qualitative results, this study proposes four validated principles for designing effective IVR spaces to support synchronous co-located collaboration.

This research delves into the integration of green roofs with Building Information Modeling (BIM), a pivotal advancement in sustainable urban construction. Aligning with the United Nations Sustainable Development Goals, particularly Goal 11, the study explores how this integration can address global challenges like climate change and resource depletion. Using the Dynamo Visual Programming Language within Autodesk Revit, the research develops a computational modeling approach for green roofs, focusing on their thermal and structural characteristics under varied environmental conditions. Key findings demonstrate the significant influence of substrate and drainage material combinations on green roofs’ thermal performance, highlighting the need for tailored designs based on climatic conditions. The study also emphasizes the importance of considering structural performance in both dry and saturated conditions for overall building integrity. The research identifies gaps in current practices, such as limited focus on specific green roof materials and reliance on certain software tools, suggesting the need for broader material selection and software adaptability. Future research directions include expanding material selections, exploring diverse environmental conditions, and integrating green roofs with various BIM software platforms. The study's implications extend to stakeholders in the construction industry, offering a framework for architects, urban planners, and policymakers to design and implement green roofs aligned with environmental goals. This work contributes to the field by proposing a novel approach to sustainable construction, integrating ecological design with digital technology, and setting a new benchmark in the integration of green roofs with BIM. By addressing these aspects, the research paves the way for future developments in sustainable urban construction, enhancing the efficiency, sustainability, and resilience of urban communities in line with global sustainability objectives.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

In econometrics and finance, volatility modelling has long been a specialised field for addressing a variety of issues pertaining to the risk and uncertainties of an asset. This study presents a robust framework, through a step-by-step design, that is relevant for effective Monte Carlo simulation (MCS) with empirical verifications to estimate volatility using the Generalized Autoregressive Score (GAS) model. The framework describes an organised approach to the MCS experiment that includes "background (optional), defining the aim, research questions, method of implementation, and summarised conclusion". The method of implementation is a workflow that consists of writing the code, setting the seed, setting the true parameter a priori, data generation process, and performance assessment through meta-statistics. Among the findings, it is experimentally demonstrated in the study that the GAS model with a lower unconditional shape parameter value can generate a dataset that adequately reflects the behaviour of financial time series data, relevant for volatility estimation. This dynamic framework is intended to help interested users on MCS experiments utilising the GAS model for reliable volatility calculations in finance and other areas.

Wild artisanal cultures, such as SCOBY-based membranes (Symbiotic Culture of Bacteria and Yeasts) and water kefir grains (WKG), are complex consortia of microorganisms comprising yeasts, lactic and acetic acid bacteria, with a large strains’ diversity and abundance. The fermented products (FPs) obtained by the microbiome’s contribution can be included into functional products due to their metabiotics (pre-, pro-, post-, and paraprobiotics) as a result of the complex and synergistic association as well as due to the metabolic functionality. In this study, both consortia of SCOBY and WKG were involved in the co-fermentation of a new formulated substrate, that was further analysed aiming at increasing of the postbiotic composition of the FPs. Plackett-Burman (PB) and Response Surface Methodology (RSM) techniques were used for the experimental designs to select and optimize the most important parameters that influence the freeze-dried starter cultures of SCOBY and WKG activity as a multiple inoculum. The tea concentration (1-3%), sugar concentration (5-10%), raisins concentration (3-6%), SCOBY lyophilized culture concentration (0.2-0.5%), WKG lyophilized culture concentration (0.2-0.5%), and fermentation time (5-7 days), were considered the independent variables for mathematical analysis and fermentation conditions’ optimization. The pH, total acidity (TA), antioxidant activity (DPPH), and antimicrobial activity against Escherichia coli ATCC 25922, Bacillus subtilis MIUG B1, Staphylococcus aureus ATCC 25923, and Aspergillus niger MIUG M5 were evaluated as responses. The rich postbiotic bioactive composition of the FP obtained in optimized biotechnological conditions highlighted the usefulness of the artisanal co-cultures, through their symbiotic metabolic interactions for the improvement of bioactive potential.

In recent years, with the rapid development of computer vision technology and the popularization of intelligent hardware, as well as people’s increasing demand for intelligent products for human-computer interaction, visual grounding technology can help machines and humans identify and locate objects, thereby promoting human-computer interaction and intelligent manufacturing. At the same time, human-computer interaction is constantly evolving and improving, becoming increasingly intelligent, humane, and efficient. This paper proposes a new VG model and designs a language verification module that uses language information as the main information to increase the model’s interactivity. Additionally, we propose the combination of visual grounding and human-computer interaction, aiming to explore the research status and development trends of visual grounding and human-computer interaction technology, as well as their application in practical scenarios and optimization directions, to provide references and guidance for relevant researchers and promote the development and application of visual grounding and human-computer interaction technology.

Clinical trials are research studies performed on people that are aimed at evaluating a medical, surgical, or behavioural intervention. It is a primary way that researchers find out if a new treatment, like a new drug or diet, or medical device is safe and effective in people. In this paper blockchain technology is embedded in a digital twin aiming to improve the quality of clinical trials through the boost of data integrity among the quality-related activities, and to promote participants' safety. First, a blockchain-embedded quality-enabled digital twin is proposed and the interactions among the enablers and peers are highlighted. Then, a prototype of the proposed system is developed, and the data of a pilot trial is used to justify the applicability of the system. The results showed that the proposed system is efficient, and hence it is feasible to adopt into a clinical trial. With the successful development of the proposed system, it is promising to provide effective data integration and knowledge management for improving participant safety.

There is a growing recognition of the need to incorporate sustainability considerations early-on in the product development (PD) process (PDP). As part of a case study at an engineering consultancy firm, this paper identifies considerations that influence the integration of sustainable design practices into real-world PD practices. This is informed by the first author getting embedded in the firm as an intern, and closely observing the PD workflow across various projects, conducting interviews and group discussions with a wide range of practitioners, and iteratively designing and testing various potential interventions. From literature and observation, we find that designers and engineers often struggle to identify and apply the right sustainable design methods and tools (SDMTs) to tackle the environmental impacts associated with their products. Through a human-centered design process, we co-created a reusable, modular framework of practices that aids the selection of relevant strategies, based on the environmental hotspots, stage of the PD process, and the client’s sustainability priorities. The paper further presents insights related to the framework’s real-world application and impacts in the firm, based on results of longitudinal engagement with the firm.

This paper addresses the alliance route network design problem considering uncertainty of unit transportation cost. An alliance route network is constructed based on the hub-and-spoke (HS) network , in which airlines can achieve inter-area passenger transport through their international gateways. The design problem is formulated with a robust model containing a set of uncertain cost parameters. The model is established based on the three-subscript model of the HS network. A case study collected from real-world data is used to test the proposed model. The results show that the robust solution can reduce the impact of cost uncertainty.

Interleaved power factor correction (PFC) is widely used circuit topology due to good efficiency and power density for single-switch boost PFC. As the differential mode (DM) electromagnetic interference (EMI) noise magnitude depends upon the input current ripple, this research details a comprehensive study of DM EMI filter design for interleaved boost PFC with the aim of minimizing the component size. It is also demonstrated that the different numbers of interleaved stages and switching frequency influence the filter attenuation requirement and, thus, the EMI filter size. First, an analytical model is derived on the basis of the Norton equivalent circuit model for the differential mode noises of interleaved boost PFC within the frequency range of 9-500 kHz. The derived model can help identify the optimal phase shifting among the interleaved boost converters in order to minimize the considered differential mode noises at the filter design frequency. So, a novel phase-shift method is developed to get a minimized attenuation required by a filter in Band B. Further, a volume optimization of the required DM filter was introduced based on the calculated filter attenuation and volumetric component parameters. Based on the obtained results, unconventional and conventional phase shifts have demonstrated a good performance in decreasing the EMI filter volume in Band B and Band A, respectively. A 2-kW interleaved PFC case study is presented to verify the theoretical analyses and the impact of phase-shifting on EMI filter size.

Enzymes are in high demand for very diverse biotechnological applications. However, natural biocatalysts often need to be engineered for fine-tuning their properties towards the end applications, such as the activity, selectivity, stability to temperature or co-solvents, and solubility. Computational methods are increasingly used in this task, providing predictions that narrow down the space of possible mutations significantly and can enormously reduce the experimental burden. Many computational tools are available as web-based platforms, making them accessible to non-expert users. These platforms are typically user-friendly, contain walk-throughs, and do not require deep expertise and installations. Here we describe some of the most recent outstanding web-tools for enzyme engineering and formulate future perspectives in this field.

Artificial reefs have been deployed in multiple regions of the world for different purposes including habitat restoration and protection, biodiversity and fish stock enhancement, fisheries management and recreation. Artificial reefs can be a valuable tool for ecosystem protection and rehabilitation, helping mitigate the effects of anthropogenic impacts that we face today. However, knowledge on artificial reefs is unevenly distributed worldwide, with some regions having much more quality information available and published (e.g. European Mediterranean Sea area), while others, for instance the North-East Atlantic area, do not. Here, we provide a characterization of purposely built artificial reefs in North-East Atlantic area based on all available literature (i.e. research papers and reports), highlighting the needs and gaps that are vital for establishing future perspectives for artificial reef deployment and research. In the North-East Atlantic area, sixty-one purposely built artificial reefs have been deployed since 1970, mostly between the years 1990-2009, with Spain being the country with the highest number of artificial reefs. The most reported purpose for their deployment is fisheries productivity and habitat/species protection, although, most artificial reefs are multipurpose in order to maximise the benefits of a given financial investment. The majority of artificial reefs were submerged at < 50 m, mainly between 10-20 m of depth. The most used designs were cubic blocks and complex designs made by an array of combined shapes, which mostly consist of concrete (79%). From all the analysed data on artificial reefs, 67% of the cases reported surveys to assess biodiversity after the deployment. However, in 26% of those cases, data was not available. When data was available, only 31% of cases reported long-term biomonitoring surveys (3 years or more). Based upon these findings, we noticed a general lack of scientifically robust data, including records of species and abundance of both fish and invertebrates, as well as macroalgae. Preventing an adequate determination of the best balance between shape, construction material and bio-colonization. Critiques and suggestions are discussed in the light of current available data in order to perform more efficient research, evaluation and functioning of future artificial reefs.

Studies have found critical software malfunctions responsible for some of the worst accidents in recent times. These malfunctions are often only minor defects that snowball into large problems; a few lines of code is all it takes. Complexity, safety, quality, and resilience are among the key attributes defining a software’s operational success. There are many leading factors for complexity, such as increases in the product size, the rate of requirement changes, and the number and type of stakeholders, and failure to manage these issues efficiently always has the same consequence, i.e., massive failure and sometimes technological catastrophe. This work analyzes some of the architecture, design, and implementation guidelines used as detection and mitigation techniques. It also discusses the safety considerations, as considering how the steam industry has handled safety issues could offer some guidance for ensuring safety. Complexity in such systems also causes some of the worst side effects from the quality auditor's perspective. While failures in the software are hard to predict, one of the most significant ways of showing preparedness is practicing software resilience. New mitigation areas, such as the fragility spectrum and failure obviation, and their usage for building a safer system are analyzed. Also discussed are various architecture styles in practice and the dramatic effect human factors can have on the success of the software being developed.

Aiming for the problems emerging in the PWM drive system with long cables, accurate modeling of power cables is the premise to predict and analyze the relevant phenomenon, and a proper filter design is the key solution to these problems. This paper proposes high-frequency cable models to represent the frequency-dependent characteristics, especially for the high-frequency resistance of the cable that is an easily overlooked factor but determines the damping of overvoltage. The proposed models can be used for accurately representing the cable parameters in a wide frequency range, and correctly simulating the differential mode (DM) overvoltage and common mode (CM) current, including the peak value, oscillation frequency and damping of the transient waveform. In addition, improved filter networks are proposed to suppress the DM voltage and CM current, with the merit of low losses, small volume and an excellent ability of suppressing overvoltage. The proposed cable models and the filter design have been validated in a 750W PWM drive system with 200m power cables.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

This paper investigates whether optimisation methods with the population made up of one solution can suffer from structural bias just like their multisolution variants. Following recent results highlighting the importance of choice of strategy for handling solutions generated outside the domain, a selection of single solution methods are considered in conjunction with several such strategies. Obtained results are tested for the presence of structural bias by means of a traditional approach from literature and a newly proposed here statistical approach. These two tests are demonstrated to be not fully consistent. All tested methods are found to be structurally biased with at least one of the tested strategies. Confirming results for multisolution methods, it is such strategy that is shown to control the emergence of structural bias in single solution methods. Some of the tested methods exhibit a kind of structural bias that has not been observed before.

Buildings use 30-40 % of all energy resources and are thus their main consumers in modern society. Moreover, buildings require a vast amount of different raw materials. During the last two decades, several green building certifications have been created in order to consider social, economic and environmental aspects of sustainability of buildings. One of the most famous and widely used of these certifications is Leadership in Energy and Environmental Design (LEED). So far, the use of LEED has concentrated in the US and other developed countries. One reason that restricts the use of this point-based system certification in developing countries is the limited data about its costs. In this study, the extra cost of the certification process will be evaluated besides the changes needed in the design of the building to reach the points required by LEED. At the first stage, the number of points the case study earns in its current format (Scenario 1) were found out, then the cost difference of getting either the Certified (Scenario 2) or Silver (Scenario 3) level LEED certification for the building was studied. It was found that besides some technical considerations, filling the criteria of the Certified and Silver level increases the total costs of construction by 3.4% and 5.9%. Further improvement of the building’s energy efficiency would enable the attainment of a higher-level certification. The results of the study could help to promote the use of green building certifications in Western Asia.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

Several design methods and principles have been presented so far, in order to guide the design of autonomous operations. Putting the required efforts into learning and using the methods for designing autonomous operations is a daunting task. Experiences so far have shown that the use of methods meant to the help the design process are often ignored. One reason could be that the design guidelines are too complex and contain much information often not relevant for the project at hand, and therefore there is no easy way to distinguish what is important from what is not. This is an issue that needs to be solved with our approach. In this article, the Autonomous Job Analysis (AJA) method is presented. The proposed methodology is created in order to guide the design of autonomous operations in maritime systems by breaking them down in to sub-operations in order to reveal challenges, needs and limitations regarding autonomous behavior. The canvas contains the categories of the AJA method on a single page format -the canvas- and each category is supported with questions to be asked during the design procedure, as well as example answers. We will describe the AJA method and the AJA canvas in detail, and present a use case scenario of an autonomous operation in order to show how they can be applied. The particular use-case is the design of an autonomous operation for the detection, inspection and tracking of a waste water plume.

Within the Active Living and Well-Being Project (RRP3), funded by the Republic of Slovenia and the European Regional Development Fund Investing in Your Future programme, we aim to develop different approaches and prototypes to provide ICT solutions for the family in order to connect its members, communicate, promote quality family time, active life, a health-friendly lifestyle and well-being, and integrate various sensor and user-based data sources into a smart city ecosystem platform. A mixed methodology, combined qualitative and quantitative approaches, was selected to conduct a study. An online survey with a structured questionnaire as well as semi-structured interviews were performed. Through the analysis of the results we tried to establish a family-centred design approach that would be inclusive as much as possible, creating benefits for all generations in order to develop interactive prototypes that would allow us to further test and verify different use-case scenarios.

The purpose of interdisciplinary communication during the early architectural design stage is to achieve the early integration of knowledge in different professional fields, which can help architects to choose correct design development strategies during the early architectural design stage. However, because there is too little information at the early design stage, and design solutions are still rapidly changing and developing, the uncertainties at this stage make it difficult for consultants in other disciplines to provide their views and analysis. In spite of this situation, the emergence of generative modeling is changing design procedures and methods of communication and cooperation for architectural teams, and has brought about a shift in the way architects transmit design information from "what" (declarative information) to "how" (procedural information). Generative modeling is like an aircraft's dashboard: It can provide a basis for interdisciplinary communication, provide interdisciplinary knowledge packages, and bring about a shift in interdisciplinary communication that will reduce the architectural team's communication needs and cost. This study uses a real design case to show the feasibility of generative modeling. Employing generative modeling as a basis, architects can enhance the efficiency of design change and multi-disciplinary communication during the early design stage, integrate specialized knowledge in relevant fields, use this knowledge to formulate design criteria for the next stage, and effectively transmit design decisions. As a consequence, the changes to the cost structure of design revisions and communication between different disciplines has initiated a paradigm shift toward multi-disciplinary communication in architectural design.

Graph coloring is a manifestation of graph partitioning, wherein, a graph is partitioned based on the adjacency of its elements. Partitioning serves potentially as a compartmentalization for any structural problem. Vertex coloring is the heart of the problem which is to find the chromatic number of a graph. The fact that there is no general efficient solution to this problem that may work unequivocally for all graphs opens up the realistic scope for combinatorial optimization algorithms to be invoked. The algorithmic complexity of graph coloring is non-deterministic in polynomial time (NP) and hard. To the best of our knowledge, there is no algorithm as yet that procures an exact solution of the chromatic number comprehensively for any and all graphs within the polynomial (P) time domain. However, several heuristics as well as some approximation algorithms have been attempted to obtain an approximate solution for the same. Here, we present a novel heuristic, namely, the 'trailing path', which returns an approximate solution of the chromatic number within polynomial time, and, with a better accuracy than most existing algorithms. The ‘trailing path’ algorithm is effectively a subtle combination of the search patterns of two existing heuristics (DSATUR and Largest First), and, operates along a trailing path of consecutively connected nodes (and thereby effectively maps to the problem of finding spanning tree(s) of the graph) during the entire course of coloring, where essentially lies both the novelty and the apt of the current approach. The study also suggests that the judicious implementation of randomness is one of the keys towards rendering an improved accuracy in such combinatorial optimization algorithms. Apart from the algorithmic attributes, essential properties of graph partitioning in random and different structured networks have also been surveyed, followed by a comparative study. The study reveals the remarkable stability and absorptive property of chromatic number across a wide array of graphs. Finally, a case study is presented to demonstrate the potential use of graph coloring in protein design – yet another hard problem in structural and evolutionary biology.

In recent years, artificial intelligence technology has widely influenced the field of design, bringing new ideas to efficiently and systematically solve urban renewal design problems. The purpose of this study is to create a stylized generation technology for building facade decoration in historic districts, which will aid in the design and control of district style and form. The goal is to use the technical advantages of conditional generative adversarial network (CGAN) in image generation and style transfer to create a method for independently designing a specific facade decoration style by interpreting image data of historical district facades. The research in this paper is based on the historical district of Putian in Fujian Province, through an experiment of image data acquisition, image processing and screening, model training, image generation, and style matching of the target area. The research found that: (1) CGAN technology can better identify and generate the decorative style of historical districts. It can realize the overall or partial scheme design of the facade; (2) in terms of adaptability, this method can provide a better scheme reference for historical district reconstruction, facade renovation, and renovation design projects. Especially for districts with obvious decorative styles, the visualization effect is better. In addition, it also has certain reference significance for the determination and design of the facade decoration style of a specific historical building; (3) This method can better learn the internal laws of the complex district style and form so as to generate a new design with a clear decoration style attribute. It can be extended to other fields of historical heritage protection to enhance practitioners' stylized control of the heritage environment and improve the efficiency and ability of professional design.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Frailty, an age-related decline in homeostatic reserves, markedly proceeded during the coronavirus disease 2019 pandemic. To continuously assess frailty status, a remote system is urgently required. We aimed to co-design/co-develop an online frailty check (FC) application alongside FC supporters who were facilitators in a pre-existing onsite FC program. The online FC included a screening measurement for sarcopenia and an 11-item questionnaire covering dietary, physical, and social behaviors. Using prototype applications, 55 opinions obtained from 32 FC supporters (median 74.0 years) were categorized and reflected refinement. Regarding the self-efficacy of FC supporters, a significant increase in social positioning was seen after the mock test (P=.031). For FC supporters and participants, the average system usability scale (SUS) score was 70.2±10.3 points, which was “marginally high” for acceptability and “good” for the adjective range. Multiple regression analysis showed that the SUS score was significantly correlated with online-onsite reliability but not online communication, even after adjusting by age, sex, education level, and ICT proficiency (b=0.400, 95% CI: 0.243-1.951, P=.013). Additionally, a significant association between onsite and online FC scores was observed (R=0.670, P=.001). Our online FC application was evaluated to be a valuable tool to practically assess frailty status remotely.

Turbo-roundabouts are one of the most frequently recommended road junction design options when it comes to increasing traffic capacity and traffic safety. This is in particular true of suburban areas, with dominant traffic flow on the main road and moderate traffic flow on the side road. Other intersections handling local traffic and considerably constricting the availability of space are usually located in the vicinity of such intersections. Another factor contributing to less availability of land for construction in these locations is the presence of surrounding residential housing. Then choosing the suitable turbo-roundabout type becomes the main issue. The article presents a case study for the selection of a type of turbo roundabout under the conditions of considerably constricted land availability, based on analyses of provision of swepth path for the chosen design vehicles. The article considers the typical Egg type turbo roundabouts, "flattened" turbo roundabouts and ellipse based roundabouts, with unconventional geometries of the truck apron and central island. For each of the analysed roundabout types setting out methods were described in detail, which enable designers to quickly select a type of roundabout suitable for specific constrained site conditions.

Background: The methods used in low- and middle-income countries (LMICs) household surveys have not changed in four decades; however, LMIC societies have changed substantially and now face unprecedented rates of urbanisation and urbanisation of poverty. This mismatch may result in unintentional exclusion of vulnerable and mobile urban populations. We compare three survey method innovations with standard survey methods in Kathmandu, Dhaka, and Hanoi, and summarize feasibility of our innovative methods in terms of time, cost, skill requirements, and experiences. Methods: We used descriptive statistics and regression techniques to compare respondent characteristics in samples drawn with innovative versus standard survey designs and household definitions, adjusting for sample probability weights and clustering. Feasibility of innovative methods was evaluated using a thematic framework analysis of focus group discussions with survey field staff, and via survey planner budgets. Results: We found that a common household definition excluded single adult (46.9%) and migrant headed households (6.7%), as well as non-married (8.5%), unemployed (10.5%), disabled (9.3%), and studying adults (14.3%). Further, standard two-stage sampling resulted in fewer single adult and non-family households than an innovative area-microcensus design; however, two-stage sampling resulted in more tent and shack dwellers. Our survey innovations provided good value for money and field staff experiences were neutral or positive. Staff recommended streamlining field tools and pairing technical and survey content experts during fieldwork. Conclusions: This evidence of exclusion of vulnerable and mobile urban populations in LMIC household surveys is deeply concerning, and underscores the need to modernize survey methods and practices.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

The threat posed by climate change, the progressive erosion of natural resources, the polluting effects related to private motorization, energy waste, excessive consumption of agricultural and natural soils and their progressive waterproofing and reduction in vegetation cover, with the subsequent environmental degradation, have highlighted the need for a sustainable management of natural resources, in terms of an equitable and ethical development, to build inclusive communities able to adapt to the negative effects of emergency phenomena, through new capacities of economic, cultural and social resilience. This contribution presents the results of the activities conducted in the RivEr/Generation_LAB, a project organized by three CIVIS members (Sapienza University of Rome, Universitè libre de Bruxelles, Universidad Autonoma de Madrid) as a part of the CIVIS Project "RivEr/Generation_LAB. Linking resilience with inclusiveness in the urban built environment of Rome, Brussels, and Madrid", financed into the Hub4 Cities, Territories &amp; Mobilities’ Call for proposals 2021. The project proposes a methodology of intervention in the Flaminio district, in particular on the 'Olympic Village' and its relationship with the Tiber River, in line with the Sustainable Development Goals, the Millennium Ecosystem Assessment and the New European Bauhaus, to establish new relationships between cities and the natural environment, favouring sustainable and inclusive public spaces.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

Ice covering on overhead transmission lines would cause damage to transmission system and long-term power outage. Among various de-icing devices, modular multilevel converter (MMC) based DC de-icer (MMC-DDI) is recognized as a promising solution due to its excellent technical performance. Its principle feasibility has been well studied, but few literature discuss its economy or hardware optimization, thus the designed MMC-DDI for high voltage transmission lines is usually too large and too expensive for engineering applications. To fill this gap, this paper presents a quantitative analysis on the converter characteristics of MMC-DDI, and calculates the minimal converter rating and its influencing factors. It reals that, for a given de-icing requirement, the converter rating varies greatly with its AC-side voltage. Then an optimization configuration is proposed to reduce the converter rating and improve its economy. The proposed configuration is verified in a MMC-DDI for a 500kV transmission line as a case study. The result shows, in the case of outputting same de-icing characteristics, the optimized converter rating is reduced from 151 MVA to 68 MVA, and total cost of MMC-DDI is reduced by 48%. This analysis and conclusion are conductive to the optimized design of multilevel DC de-icer, then to its engineering application.

Almond (Prunus dulcis (Mill.) D.A.Webb) is one of the most important nut crops both in terms of area and production. Over the last decades, an important part of the beneficial actions for health associated with their consumption was attributed to the phenolic compounds, mainly accumulated in almond skin. Interestingly, after cold-pressed oil extraction, most of these antioxidant phenolic compounds are retained in a skin-enriched by-product, so-called almond cold-pressed oil residue. In Morocco, ranked fifth producer in the world, this production generates an important part of this valuable byproduct. In the present study, using a multivariate Box-Behnken design, an ultrasound-assisted extraction (USAE) method of phenolic compounds from Moroccan almond cold-pressed oil residue was developed and validated. Response surface methodology resulted in the optimal extraction conditions: the use of aqueous EtOH 53.0% (v/v) as green solvent, applying an US frequency of 27.0 kHz for an extraction duration of 29.4 min. The present USAE allowed substantial gains in terms of extraction efficiency compared to conventional heat reflux extraction. Applied to 3 different local Beldi genotypes growing at 3 different experimental sites, the optimal USAE conditions led to a total phenolic content of 13.86 mg/g dry weight (DW). HPLC analysis revealed that the main phenolic compounds from this valuable byproduct were: chlorogenic acid followed by protocatechuic acid, p-hydrobenzoic acid and p-coumaric acid. The accumulation of these phenolic compounds appeared to be more dependent on the genetic background than on the environmental impact here represented by the 3 experimental culture sites. Both in vitro cell free and cellular antioxidant assays were performed, and revealed the great potential of these extracts. In particular, correlation analysis evidenced the prominent roles of chlorogenic acid, protocatechuic acid and p-hydrobenzoic acid. To summarize, the USAE method presented here is a quick, green, simple and efficient validated USAE for the possible valorization of antioxidant phenolic compounds from Moroccan almond cold-Pressed oil residues, making it possible to generate extracts with attractive antioxidant activities for future nutraceutical and/or cosmetic applications.

Algorithms, indispensable to understand Artificial Intelligence (AI), are omnipresent in social media but users’ understanding of these computational processes and the way they impact their consumption of information is often limited. There is a need for Media and Information Literacy (MIL) research investigating a) how MIL can support Algorithm Literacy (AL) as a subset of competences, and with what working definition, b) what competences users need in order to evaluate algorithms critically and interact with them effectively, and c) how to design learner-centred interventions that foster increased user understanding of algorithms and better response to disinformation spread by such processes. Based on Crossover project research, this paper looks at four scenarios of use by journalists, developers and MIL experts that mirror users’ daily interactions with social media. The results suggest several steps towards integrating AL within MIL goals, while providing a concrete definition of Algorithm-literacy that is experience-based. The competences and design considerations are organised in a conceptual framework thematically derived from the experimentation. This contribution can support AI developers and MIL educators in their co-design of algorithm-literacy interventions and guide future research on AL as part of a set of nested AI literacies within MIL.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

The acquired immunodeficiency syndrome (AIDS) caused by the human immunodeficiency virus (HIV) continues to be a public health problem. In 2020, 680,000 people died from HIV-related causes, and 1.5 million people were infected. Antiretrovirals are only a way to control HIV infection but not to cure AIDS. As such, effective treatment must be developed to control AIDS. Developing a drug is not an easy task, and there is an enormous amount of work and economic resources invested. For this reason, it is highly convenient to employ computer-aided drug design methods, which can help generate and identify novel molecules. Using the de novo design, new novel molecules can be developed using fragments as building blocks. In this work, we develop a virtual-focused compound library of HIV-1 viral protease inhibitors from natural product fragments. Natural products are characterized by a large diversity of functional groups, many sp3 atoms, and chiral centers. Pseudo-natural products are a combination of natural products fragments that keep the desired structural characteristics from different natural products. An interactive version of chemical space visualization of virtual compounds focused on HIV-1 viral protease inhibitors from natural product fragments is freely available at https://figshare.com/s/ceb58d58e8f5585ce67e.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

This study reports on empirical findings of participatory design workshops for the development of a supportive user experience design system in the automotive. Identifying and addressing this area with traditional research methods is problematic due to the different UX design perspectives that might be conflicting and the related automotive domain limitations. To help resolve this problem, we conducted research with 12 User Experience (UX) designers through individual participatory prototyping activities to gain insights on their explicit, observable, tacit and latent needs. These activities allowed us to explore their motivation to use different technologies; the system's architecture; detailed features of interactivity and describe user needs including Efficiency, Effectiveness, Engagement, Naturalness, Ease of Use, Information retrieval, Self-Image awareness, Politeness, and Flexibility. Our analysis led us to design implications that translate participants' needs into UX design goals, informing practitioners on how to develop relevant systems further.

Renewable energy sources will play a central role in the sustainable energy systems of the future. Scenario analyses of such hypothesized energy systems require sound knowledge of the techno-economic potential of renewable energy technologies. Although there have been various studies concerning the potential of offshore wind energy, higher spatial resolution, as well as the future design concepts of offshore wind turbines, has not yet been addressed in sufficient detail. Here, we aim to overcome this gap by applying a high spatial resolution to the three main aspects of offshore wind potential analysis, namely ocean suitability, the simulation of wind turbines and cost estimation. A set of constraints is determined that reveal the available areas for turbine placement across Europe’s maritime boundaries. Then, turbine designs specific to each location are selected by identifying turbines with the cheapest levelized cost of electricity (LCOE), restricted to capacities, hub heights and rotor diameters of between 3-20 MW, 80-200 m and 80-280 m, respectively. Ocean eligibility and turbine design are then combined to distribute turbines across the available areas. Finally, LCOE trends are calculated from the individual turbine costs, as well as the corresponding capacity factor obtained by hourly simulation with wind speeds from 1980 to 2017. The results of cost-optimal turbine design reveal that the overall potential for offshore wind energy across Europe will constitute nearly 8.6 TW and 40.0 PWh at roughly 7 €_ct kWh^-1 average LCOE by 2050. Averaged design parameters at national level are provided in an appendix.

This paper presents a two-stage hierarchical neural network using image classification and object detection algorithms as key building blocks for a system that automatically detects a potential design right infringement. This neural network is trained to return the Top-N original design right records that highly resemble the input image of a counterfeit. Design rights specify the unique aesthetic characteristics of a product. Due to the rapid change of trends, new design rights are continuously generated. This work proposes an Ensemble Neural Network (ENN), an artificial neural network model that aims to deal with a large amount of counterfeit data and design right records that are frequently added and deleted. At first, we performed image classification and objection detection learning per design right using the existing models with a proven track record of high accuracy. The distributed models form the backbone of the ENN and yield intermediate results aggregated at a master neural network. This master neural network is a deep residual network paired with a fully connected network. This ensemble layer is trained to determine the sub-models that return the best result for a given input image of a product. In the final stage, the ENN model multiples the inferred similarity coefficients to the weighted input vectors produced by the individual sub-models to assess the similarity between the test input image and the existing product design rights to see any sign of violation. Given 84 design rights and the sample product images taken meticulously under various conditions, our ENN model achieved average Top-1 and Top-3 accuracies of 98.409% and 99.460%, respectively. Upon introducing new design rights data, a partial update of the inference model was done an order of magnitude faster than the single model. ENN maintained a high level of accuracy as it scaled out to handle more design rights. Therefore, the ENN model is expected to offer practical help to the inspectors in the field, such as the customs at the border that deal with a swarm of products.

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

Wire-driven hyper-redundant continuum manipulators are gaining more popularity and finding more applications in industry and in minimally invasive surgery. Unlike traditional rigid link manipulators, continuum robots with a flexible backbone structure are able to work in a highly constrained workspace and in an unstructured environment. However, in spite of a possible wide range of reachability, continuum manipulators have some issues related to payload capacity, accuracy and control. Therefore, in this research, we propose a novel hyper-redundant continuum robot with a passive sliding disc mechanism to improve payload capacity and accuracy. To prove the sliding mechanism concept, we demonstrate a comparison analysis with a conventional non-sliding continuum robot arm in a payload test, a bending test and a reachability test. Moreover, with this novel design, we are proposing robot kinematics and kinetic formulation and simulation results to validate the effectiveness of the sliding disc mechanism.

Genetic testing has expanded out of the research laboratory into medical practice and the direct-to-consumer market, and rapid analysis of the resulting genotype data can now have significant impact. We present a method for summarizing personal genotypes as ‘genotype fingerprints’ that meet these needs. Genotype fingerprints can be derived from any single nucleotide polymorphism (SNP)-based assay, and remain comparable as chip designs evolve to higher marker densities. We demonstrate that they support distinguishing types of relationships among closely related individuals and closely related individuals from individuals from the same background population, as well as high-throughput identification of identical genotypes, individuals in known background populations, and de novo separation of subpopulations within a large cohort through extremely rapid comparisons. While fingerprints do not preserve anonymity, they provide a useful degree of privacy by summarizing a genotype in a way that prevents reconstruction of individual marker states. Genotype fingerprints are therefore well-suited as a format for public aggregation of genetic information to support ancestry and relatedness determination without revealing personal health risk status.

Urban Green Space (UGS) has important impacts on human health, but an integrated participatory approach to UGS design for improved residents’ health was lacking to date. The aim of our study was to develop and evaluate such a novel approach to address this gap. The approach was developed following guiding principles from the literature, and tested with groups of children and elderly as participants in two neighborhoods of Maastricht (The Netherlands) with a low score on economic and health indicators. Novel aspects of the approach are the inclusion of both positive and negative health effects, the combination of participant self-assessment and model-based assessment of the health effects of UGS designs, and the use of maps to visualize UGS designs and health effects. The participant-generated UGS designs resulted in a considerable self-assessed increase in use of the UGS for meeting, stress reduction or leisure-based physical activity, as compared to the current situation. The model-assessed positive and negative health effects of the participant-generated UGS designs were limited. The major strength of the developed approach is that it combines active participation of residents in UGS (re)design with assessment of the health effects of these UGS designs. Whereas in other participatory approaches to UGS design it often remains unclear whether the resulting designs represent an improvement in terms of health, our combination of computer model-based assessment and a participatory process produced clear outcomes regarding the health benefits and use of UGS designs.