Accurate channel estimation is of utmost importance for massive MIMO systems to provide significant improvements in spectral and energy efficiency. In this work, we present a study on the distribution of a simple but yet effective and practical channel estimator for multi-cell massive MIMO systems suffering from pilot-contamination. The proposed channel estimator performs well under moderate to aggressive pilot contamination scenarios without previous knowledge of the inter-cell large-scale channel coefficients and noise power, asymptotically approximating the performance of the linear MMSE estimator as the number of antennas increases. We prove that the distribution of the proposed channel estimator can be accurately approximated by the circularly-symmetric complex normal distribution, when the number of antennas, M, deployed at the base station is greater than 10.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

In the oil palm industry, stands age is an important parameter to monitor the sustainability of cultivation, to develop the growth yield model, to identify the disease or stressed area, and to estimate the carbon storage capacity. This research is focused to estimate and distinguish oil palm stands age based on crown/ canopy density obtained using Forest Canopy Density (FCD) model derived from four indices as follows; Advanced Vegetation Index, Bare Soil Index, Shadow Index, and Thermal Index. FCD model employs multi temporal image analysis resulting four classes of oil palm stands age categorized as seed with FCD value of 29–56% (0 years), young with FCD value of 56–63% (1–9 years), teen with FCD value of 63–80% (10–15 years), and mature with FCD value of >80% (>15 years). Minimum canopy density value is 29% even in the zero years old indicates incomplete land clearance or the type of seed planted in the land.

With quick improvement in the field of network, everything becomes online. Remote user authentication is a mechanism in which remote server verify the correctness of user over common or public channel. Remote user authentication can be Single server authentication or Multi server authentication. The disadvantage of single server authentication is that the user needs to recall user id and password for each service, he/she need to utilize, however it can overcome by Multi-server authentication in which user needs to register himself with Registration Center (RC) for the first run through and after that onwards he can utilize each service (which are given by servers, associated with RC) by recollecting only one user id and password. In this paper, we analyze Chen's authentication scheme (based on multi server authentication) and show that this scheme is vulnerable to password guessing attack, replay attack, RC spoofing attack, session key verification attack and perfect forward secrecy attack. In this Paper, we propose a biometric based remote user authentication scheme in multi-server environment. Proposed scheme is more secure and efficient as compared to chen's scheme\cite{23}.

UAS-based multi-spectral imagery is becoming increasingly popular for the improved monitoring and managing of various horticultural crops. However, for UAS data to be used as an industry standard for assessing tree structure and condition as well as production parameters, it is imperative that the appropriate data collection and pre-processing protocols are established to enable multi-temporal comparison. There are several UAS-based radiometric correction methods commonly used for precision agricultural purposes. However, their relative accuracies have not been assessed for data acquired in complex horticultural environments. This study assessed the variations in estimated surface reflectance values of different radiometric corrections applied to multi-spectral UAS imagery acquired in both avocado and banana orchards. We found that inaccurate calibration panel measurements, inaccurate signal-to-reflectance conversion, and high variation in geometry between illumination, surface, and sensor viewing produced significant radiometric variations in at-surface reflectance estimates. Potential solutions to address these limitations included appropriate panel deployment, site-specific sensor calibration, and appropriate BRDF correction. Future UAS based horticultural crop monitoring can benefit from the proposed solutions to radiometric corrections to ensure they are using comparable image-based maps of multi-temporal biophysical properties.

There is an ongoing global pandemic of human respiratory syncytial virus (RSV) infection that results in substantial annual morbidity and mortality. In Australia, RSV is the major cause of acute lower respiratory tract infections (ALRI). Nevertheless, little is known about the extent and origins of genetic diversity of RSV in Australia, nor the factors that shape this diversity. We conducted a genome-scale analysis of RSV infections in New South Wales (NSW). RSV genomes were successfully sequenced for 144 specimens collected between 2010-2016. Of these, 64 belonged to the RSVA and 80 to the RSVB subtype. Phylogenetic analysis revealed a wide diversity of RSV lineages within NSW and that both subtypes evolved rapidly in a strongly clock-like manner, with mean rates of approximately 6-8 x 10^-4 nucleotide substitutions per site per year. There was only weak evidence for geographic clustering of sequences, indicative of fluid patterns of transmission within the infected population, and no evidence of any clustering by patient age such that viruses in the same lineages circulate through the entire host population. Importantly, we show that both subtypes circulated concurrently in NSW with multiple introductions into the Australian population in each year, and only limited evidence for multi-year persistence.

We describe a multi-resolution approach for audio classification and illustrate its application to the open data set for environmental sound classification. The proposed approach utilizes a multi-resolution based ensemble consisting of targeted feature extraction of approximation (coarse scale) and detail (fine scale) portions of the signal under the action of multiple transforms. This is paired with an automatic machine learning engine for algorithm and parameter selection and the LSTM algorithm, capable of mapping several sequences of features to a predicted class membership probability distribution. Initial results show an improvement in multi-class classification accuracy.

Recent analyses of cosmic microwave background surveys have revealed hints that there may be a non-trivial running of the running of the spectral index. If future experiments were to confirm these hints, it would prove a powerful discriminator of inflationary models, ruling out simple single field models. We discuss how isocurvature perturbations in multi-field models can be invoked to generate large runnings in a non-standard hierarchy, and find that a minimal model capable of practically realising this would be a two-field model with a non-canonical kinetic structure. We also consider alternative scenarios such as variable speed of light models and canonical quantum gravity effects and their implications for runnings of the spectral index.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

The airport ground handling service (AGHS) equipment vendor selection (AGHSEVS) problem is critical for ramp work safety management, because AGHS equipment malfunctions affect airport ramp work safety. Appropriate vendor selection can prevent aircraft damage and delays in airlines schedules, and ensure reliable and high-quality ground handling service. The AGHSEVS problem is a time-consuming and complex process that requires professional knowledge and experience to make judgments. Specifically, AGHSEVS is a multi-criteria decision-making (MCDM) problem. Previous research has seldom integrated MCDM methods with linear and goal programming to solve the AGHSEVS problem. The objective of this study was to develop a new system evaluation model for AGHSEVS by considering both qualitative and quantitative methods. We test the proposed approach on an AGHS company in Taiwan.

Smart agriculture is a new way of farming that uses advanced technology. It makes a significant contribution to improving the efficiency and productivity of farming practices. Systems that use drones to monitor pests and spray pesticides greatly reduce the burden on farmers. In addition, remote sensing technology facilitates the monitoring of crop growth conditions and the early detection of diseases and pests. However, the high cost of equipment to communicate sensor data is preventing farmers from adopting sensing systems. As a result, many studies have been conducted to make the sensing system available at a low cost. Nevertheless, many farmers have not yet adopted them. Therefore, this paper proposes an agricultural sensor network system using drones and optical camera communication (OCC). The proposed system aims to achieve high-density farm sensing at low cost. The proposed system uses OCC as the communication method for sensor data. Low cost light sources such as LED panels can be used as transmitters. In addition, existing agricultural drones equipped with cameras can be used as receivers. We also propose a trajectory control algorithm for the receiving drone to efficiently collect the sensor data. The proposed system is suitable for deploying sensor networks in areas with underdeveloped infrastructure and radio silence. In this paper, we conducted a preliminary experiment at a leaf mustard farm in Kamitonda-cho, Wakayama to demonstrate the effectiveness of the proposed system using a Mavic 2 Pro drone, launched by DJI Co., Ltd.

In contrast to conventional non-destructive testing (NDT) and non-destructive evaluation (NDE) methodologies, including radiography, ultrasound, and eddy current analysis, the coplanar capacitive sensing technique emerges as a novel and promising avenue within the field. This paper endeavors to elucidate the efficacy of coplanar capacitive sensing, also referred to as capacitive imaging (CI), within the realm of NDT. Leveraging extant scholarly discourse, this review offers a comprehensive and methodical examination of the coplanar capacitive technique, encompassing its fundamental principles, factors influencing sensor efficacy, and diverse applications for defect identification across various NDT domains. Furthermore, this review deliberates on extant challenges and anticipates future trajectories for the technique. The manifold advantages inherent to coplanar capacitive sensing vis-à-vis traditional NDT methodologies not only afford versatility in application but also underscore its potential for pioneering advancements in forthcoming applications.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.

This study aims to provide analyses of the levels of airborne particulate matter (PM) using a two-pronged approach that combines data from in situ Internet of Things (IoT) sensor networks with remotely sensed aerosol optical depth (AOD). Our approach involved setting up a network of custom-designed PM sensors that could be powered by the electrical grid or solar panels. These sensors were strategically placed throughout densely populated areas of North Texas to collect data on PM levels, weather conditions, and other gases from September 2021 to June 2023. The collected data was then used to create models that predict PM concentrations in different size categories, demonstrating high accuracy with correlation coefficients greater than 0.9. This highlights the importance of collecting hyperlocal data with precise geographic and temporal alignment for PM analysis. Furthermore, we expanded our analysis to a national scale by developing machine learning models that estimate hourly PM2.5 levels throughout the continental United States. These models used high-resolution data from the Geostationary Operational Environmental Satellites (GOES-16) Aerosol Optical Depth (AOD) dataset, along with meteorological data from the European Center for Medium-Range Weather Forecasting (ECMWF), AOD reanalysis, and air pollutant information from the MERRA-2 database, covering the period from January 2020 to June 2023. Our models were refined using ground truth data from our IoT sensor network, the OpenAQ network, and the National Environmental Protection Agency (EPA) network, enhancing the accuracy of our remote sensing PM estimates. The findings demonstrate that the combination of AOD data with meteorological analyses and additional data sets can effectively model PM2.5 concentrations, achieving a significant correlation coefficient of 0.849. The reconstructed PM2.5 surfaces created in this study are invaluable for monitoring pollution events and performing detailed PM2.5 analyzes. These results were further validated through real-world observations from two in situ MINTS sensors located in Joppa (South Dallas) and Austin, confirming the effectiveness of our comprehensive approach to PM analysis. The US Environmental Protection Agency (EPA) recently updated the national standard for PM2.5 to 9 μg/m3, a move aimed at significantly reducing air pollution and protecting public health by lowering the allowable concentration of harmful fine particles in the air. Using our analysis approach to reconstruct the fine-time resolution PM2.5 distribution across the entire United States for our study period, we found that the entire nation encountered PM2.5 levels that exceeded 9 μg/m3 for more than 20% of the time of our analysis period, with the eastern United States and California experiencing concentrations exceeding 9 μg/m3 for over 50% of the time, highlighting the importance of regulatory efforts to maintain annual PM2.5 concentrations below 9 μg/m3.

Predicting anomalies in manufacturing assembly lines is crucial for reducing time and labor costs and improving processes. For instance, in rocket assembly, premature part failures can lead to significant financial losses and labor inefficiencies. With the abundance of sensor data in the Industry 4.0 era, machine learning (ML) offers potential for early anomaly detection. However, current ML methods for anomaly prediction have limitations, with F1-measure scores of only 50% and 66% for prediction and detection, respectively. This is due to challenges like the rarity of anomalous events, scarcity of high-fidelity simulation data (actual data is expensive), and the complex relationships between anomalies not easily captured by traditional ML approaches. Specifically, these challenges relate to two dimensions of anomaly prediction: predicting when anomalies will occur and understanding the dependencies between them. This paper introduces a new method called Robust and Interpretable 2D Anomaly Prediction (RI2AP) designed to address both dimensions effectively. RI2AP is demonstrated on a rocket assembly simulation, showing up to a 30-point improvement in F1 measure compared to current ML methods. This highlights its potential to enhance automated anomaly prediction in manufacturing. Additionally, RI2AP includes a novel interpretation mechanism inspired by a causal-influence framework, providing domain experts with valuable insights into sensor readings and their impact on predictions. Finally, the RI2AP model is deployed in a real manufacturing setting for assembling rocket parts. Results and insights from this deployment demonstrate the promise of RI2AP for anomaly prediction in manufacturing assembly pipelines.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Modal testing is a common step in aerostructure design, serving to validate the predicted natural frequencies and mode shapes obtained through computational methods. The strategic placement of sensors during testing is crucial to accurately measuring the intended natural frequencies. However, conventional methodologies for sensor placement are often time-consuming and involve iterative processes. This study explores the potential of machine learning techniques to enhance sensor selection methodologies. Three machine learning-based approaches are introduced and assessed, comparing their efficiency with established techniques. The evaluation of these methodologies is conducted using a numerical model of a beam to simulate real-world scenarios. The results offer insights into the efficacy of machine learning in optimizing sensor placement, presenting an innovative perspective on enhancing the efficiency and precision of modal testing procedures in aerostructure design.

The purpose of this study was to investigate the relationship between clinical outcomes and lateral thrust before and after unicompartmental knee arthroplasty (UKA) using inertial measurement sensor units. Eleven knees were evaluated with gait analysis. The varus angular velocity was used to evaluate lateral thrust. The femoro-tibial angle (FTA) and hip-knee-ankle angle (HKA) were used to evaluate lower limb alignment, and Oxford Knee Score (OKS) and Japanese Orthopaedic Association Score (JOA) were used to evaluate clinical outcomes. The mean pre-UKA peak varus velocity was 37.1 ± 9.8°/sec, and that of post-UKA was 28.8 ± 9.1°/sec (p=0.00003). Assuming the definition of lateral thrust is when varus angular velocity is more than 28.1°/sec, 81.8% of patients had lateral thrust preoperatively, but this decreased to 55.6% postoperatively. Both OKS and JOA improved after surgery. In addition, HKA was -7.9° preoperatively and -5.8° postoperatively (p=0.024), and FTA was 181.4° preoperatively and 178.4° postoperatively (p=0.012). There was a positive correlation between postoperative JOA and FTA, indicating that changes in postoperative alignment affected clinical outcomes. This study quantitatively evaluated the disappearance of lateral thrust by UKA, and it found that the stability can be achieved by UKA for unstable knees with lateral thrust.

Recent advances in artificial intelligence combined with behavioral sciences have led to the development of cutting-edge tools for recognizing human emotions based on text, video, audio, and physiological data. However, these data sources are expensive, intrusive, and regulated, unlike plants which have been shown to be sensitive to human steps and sounds. A methodology is proposed to use plants as human emotion detectors. Electrical signals from plants are tracked and labeled based on video data. Labeled data are then used for classification. MLP, biLSTM, MFCC-CNN, MFCC-ResNet, and additionally, Random Forests, 1-Dimensional CNN, and biLSTM without windowing models are set using a grid search algorithm with cross-validation. Finally, best-parameterized models are trained and used with the test set for classification. The performance of this methodology is measured with a case study with 54 participants, who were watching an emotionally charged video, as ground truth their facial emotions were simultaneously measured using face emotion analysis. The Random Forest model shows the best performance, particularly in recognizing high-arousal emotions, achieving an overall weighted accuracy of 55.2% and demonstrating high weighted recall in emotions such as fear 61.0% and happiness 60.4%. The MFCC-ResNet model offers decently balanced results, with Accuracy(MFCC-ResNet)=0.318 and Recall (MFCC-ResNet)=0.324. With the MFCC-ResNet model fear and anger are recognized with 75% and 50% recall respectively. Thus, using plants as an emotion recognition tool seems worth investigating, addressing both cost and privacy concerns.

This project involves the development of Fire Suppression System (FSS) leveraging of Home automation system using Graphical System design (LabVIEW) software and Arduino microcontroller for real-time monitoring and control. The system integrates an Infrared (IR) flame sensor, an MQ2 gas sensor to detect and suppress fire hazards efficiently. The LabVIEW interface facilitates real-time monitoring of sensor data, allowing users to visualize and analyze the environmental conditions. Through this system, fires are automatically subdued, enhancing safety without requiring human intervention. This advances fire safety by swiftly containing threats and minimizing potential damage.

Advances in biomimetic triboelectric nanogenerators (TENGs) have significant implications for electronic skin (e-skin) and human-machine interaction (HMI). Emphasizing the need to mimic complex functionalities of natural systems, particularly human skin, TENGs leverage triboelectricity and electrostatic induction to bridge the gap in traditional electronic devices' responsiveness and adaptability. The exploration begins with an overview of TENGs' operational principles and modes, transitioning into structural and material biomimicry inspired by plant and animal models, proteins, fibers, and hydrogels. Key applications in tactile sensing, motion sensing, and intelligent control within e-skins and HMI systems are highlighted, showcasing TENGs' potential in revolutionizing wearable technologies and robotic systems. This review also addresses the challenges in performance enhancement, scalability, and system integration of TENGs. It points to future research directions, including optimizing energy conversion efficiency, discovering new materials, and employing micro-nanostructuring techniques for enhanced triboelectric charges and energy conversion. The scalability and cost-effectiveness of TENG production, pivotal for mainstream application, are discussed along with the need for versatile integration with various electronic systems. The review underlines the significance of making bioinspired TENGs more accessible and applicable in everyday technology, focusing on compatibility, user comfort, and durability. Conclusively, it underscores the role of bioinspired TENGs in advancing wearable technology and interactive systems, indicating a bright future for these innovations in practical applications.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

Barrier coverage is a fundamental application in wireless sensor networks, which is widely used to protect a region through intruder detection for smart city. In this paper, we study a new branch of barrier coverage, named warning barrier coverage (WBC). Different from the classic barrier coverage, WBC has the inverse protect direction, which protects unexpected visitors by warning them away from the region enclosed by sensor barriers. The WBC holds a promising prospect in many danger keep out applications for smart city. For example, a WBC can enclose the debris area in the sea and alarm any approaching ships in order to avoid their damaging propellers. One special feature of WBC is that the target region is usually dangerous and its boundary is previously unknown. Hence, the scattered mobile nodes need to detect the boundary and form the barrier coverage themselves. It is challenging to form these distributed sensor nodes into a barrier because a node can sense only the local information and there is no global information of the unknown region or other nodes. To this end, we propose a novel solution AutoBar for mobile sensor nodes to automatically form a WBC for smart city. To pursue the high coverage quality, we theoretically derive the optimal distribution pattern of sensor nodes using convex theory. Based on the analysis, we design a fully distributed algorithm that enables nodes to collaboratively move towards the optimal distribution pattern. In addition, AutoBar is able to reorganize the barrier even any node is broken. To validate the feasibility of AutoBar, we develop the prototype of the specialized mobile node, which consists of two kinds of sensors: one for boundary detection and another for visitor detection. Based on the prototype, we conduct extensive real trace driven simulations in various smart city scenarios. Performance results demonstrate that AutoBar outperforms the existing barrier coverage strategies in terms of coverage quality, formation duration, and communication overhead.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

Sensor networks, as a special subtype of wireless networks, consist of sets of wirelessly connected sensor nodes often placed in hard-to-reach environments. Therefore, it is expected that sensor nodes will not be powered from the power grid. Instead, sensor nodes have their own power sources, the replacement of which is often impractical and requires additional costs, so it is necessary to ensure minimum energy consumption. For that reason, the energy efficiency of wireless sensor networks used for monitoring environmental parameters is essential, especially in remote networking scenarios. In this paper, an overview of the latest research progress on wireless sensor networks based on LoRa was provided. Furthermore, the analyses of the energy consumption of sensor nodes used in agriculture to observe environmental parameters were carried out. Optimization methods of energy consumption, in terms of choosing the appropriate data collection processes, as well as the settings of wireless network radio parameters were suggested. In the conducted analyses, special emphasis was placed on choosing the optimal package size. In this paper, it was proven that the adjustment of the transmission speed to the actual size of the packet is important for better energy efficiency of communication.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

Vascular endothelial growth factor (VEGF) is a important biomarker with significant clinical importance. It plays a key role in angiogenesis, would healing, tumor growth, lung development, and in retinal diseases. Hence, detecting and quantifying VEGF is crucial in clinical diagnosis and prognosis of various diseases. In this work, a simple but highly cost-effective platform is developed for VEGF protein detection by using commercially available interdigitated sensors that are modified through surface chemistry tagged with DNA aptamer grafting. The dielectric characteristics between the fingers of sensor is modulated by the negatively charged aptamer-VEGF capture and the impedance is estimated using impedance analyzer. Impedance spectra tests was compared between pristine unmodified, functionalized monolayer surfaces and aptamer-grafted surfaces in order to evaluate the efficacy of VEGF detection. In our results, the sensitivity experiments as conducted had shown the ability of the interdigitated sensor to detect VEGF at a low concentration of 5 pM. The specificity of the functionalized sensor in detecting VEGF is further studied by comparing the impedance to platelet-derived growth factor (PDGF), and the results confirm the specificity of the sensor. Finally, an alternative illustration of impedance spectra is also proposed to improve the data visualization, and such presentation may be potential for intelligent VEGF detection.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

In order to realize the accurate measurement of wearable sphygmomanometer, this paper selects the micro electro mechanical system (MEMS) pressure sensor with small size, low cost and high accuracy, and proposes a flexible packaging method combining Parylene and Polydimethylsiloxane (PDMS). The flexible packaging sensor protects the sensor chip while ensuring the comfort of the measured person. It can be worn for a long time, and the encapsulated sensor has good accuracy and sensitivity. At the same time, the encapsulated MEMS pressure sensor was used to collect good pulse signals and extract multiple pulse wave characteristic parameters. A blood pressure measurement method based on the combination of arterial tonometry method and pulse wave parameters method was proposed, and multiple machine learning algorithms were compared and analyzed to select the algorithm model with the smallest error as the optimal regressor. The experimental results show that the blood pressure measurement method combining the arterial tonometry method and the pulse wave parameters method can effectively improve the accuracy of blood pressure measurement. The experimental results demonstrate that the combination of arterial tonometry and pulse wave parameter methods can effectively enhance the accuracy of blood pressure measurement, with the random forest model serving as the optimal regressor. The average deviation between the systolic blood pressure measured by our self-made sphygmomanometer and the commercial sphygmomanometer was 0.86mmHg, with a standard deviation of 4.04mmHg. The average deviation of diastolic blood pressure was 0.63mmHg, with a standard deviation of 5.15mmHg, meeting the AAMI standard for clinical practice.

Precision Agriculture is the ability to handle variations in productivity within a field and maximize financial return, optimize resource utilization and minimize impact of the environment. It is also the process of automated data collection, cloud storage and utilization to build robust decision support system. In case of Ethiopia, due to poor communication infrastructure coverage and absence of the state-of-the-art technology in the agriculture sector, implementing precision farming system is a challenging tasks in the domain area. In this work, we proposed a fusion of multiple sensors using IOT and IIOT infrastructure to collect critical data from farming fields to develop precision farming facility for decision makers. The main purpose was to monitor weather variability, automate irrigation process, extract critical soil properties. In addition, we have used time series data collected from sensor devices to build forecasting model. Fusion of multiple IoT device provide a mechanism in the agriculture area to deal with real-time monitoring of crops. It is cost-effective technology and required low-energy with edge computing sensor device. We employed the Message Queuing Telemetry Transport (MQTT) protocol to connect the Industrial/Internet of Things (I/IoT) to the cloud server. The communication between system user and sensor device has been done via cloud using Node-RED platform, web android APIs. The cloud-based Eco-system allows us to aggregate, visualize, and analyze live streams output from each sensor in real-time manner. Finally, we have built time series forecasting model using records collected by each sensor device. Using the multi-variate time series data-set, we have obtained about 99 forecasting accuracy on some important variables. Finally, we have developed mobile and web-based application for the end-user to monitor the proposed system remotely.

The present work demonstrates the optimization of the ligand structure in the series of bis-phosphine oxide and carbamoylphosphine oxide representatives for efficient coordination of Tb3+ and Eu3+ ions with the formation of the complexes exhibiting high Tb3+- and Eu3+-centered luminescence. The analysis of the stoichiometry and structure of the lanthanide complexes obtained by XRD method reveals the great impact of the bridging group nature between two phosphine oxide moieties on the coordination mode of the ligands with Tb3+ and Eu3+ ions. The bridging imido-group facilitates the deprotonation of imido-bisphosphine oxide ligand followed by the formation of tris-complexes. The spectral and PXRD analysis of the separated colloids indicates that the high stability of the tris-complexes provides their safe conversion into polystyrenesulfonate-stabilized colloids under the solvent exchange method. The red Eu3+-centered luminescence of the tris-complex exhibits the same specificity in the solutions and the colloids. The pronounced luminescent response on the antibiotics ceftriaxone allows to sense the latter in aqueous solutions with the LOD value equal to 0.974 M.

When present in specific amounts in the air, the colorless, odorless, and tasteless gases monoxide and carbon dioxide may either replace oxygen in red blood cells (CO) or increase the respiratory rate causing cardiac arrhythmias (CO2), leading to death. Commercial sensors take around 8 h to detect levels of CO (50 PPM), causing moderate poisoning. SnO2 presents controlled interactions with the atmosphere using conductance and vacancy adjustments to capture electrical properties. However, the selectivity of gas detection by SnO2 can still be improved, thus also increasing the application possibilities. The present study aimed to optimize the sensing of CO and CO2 in SnO2 using palladium functionalization. The vapor-liquid-solid method synthesized a network of SnO2 nanobelts decorated with palladium nanoparticles. The sensitivity of the sensors for CO and CO2 were evaluated, characterizing parameters such as response time, a wide range of CO and CO2 concentrations, and temperature. In the seventh measurement cycle, the sensor response for different concentrations of gases in consecutive cycles showed a sensitivity of up to 125% for CO in 60 s. Furthermore, we observed increased sensor sensitivity with material doping with nanoparticles from 130 ppm to 1360 ppm in 30 seconds to CO. Conclusion: The results provide a better understanding of the sensitivity of SnO2 in palladium-decorated nanoparticles, offering insights for detecting low CO concentrations quickly. The behavior of these doped nanosensors showed us the importance of considering them as a practical possibility for detecting these gases of importance to human health.

Consumer rhythm-monitoring devices, such as the Apple Watch, are becoming more readily available. Irregular pulses can be detected using an optical sensor built into the wearable device. The Apple Watch (Apple Inc., Cupertino, CA, USA) is a class II medical device with pulse rate and electrocardiography (ECG) monitoring capabilities. Here we report a case in which an arrhythmia that was conventionally perceived but undiagnosed was identified as atrial fibrillation by self-acquisition of ECG data using an Apple Watch.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

In this paper, an all-fiber Mach-Zehnder interferometer (MZI) sensor for refractive index (RI) measuring is presented, which is based on Multimode–Single-mode–Multimode (MSM) fiber. The effects of both reducing the radius of the sensing part and the surface plasmon resonance (SPR) on its efficiency are investigated. Increasing the interaction of high-order modes with external media, caused by etching the cladding layer of the single-mode fiber part, significantly improves the sensitivity. Both wavelength and intensity interrogation approaches are employed to study the Multimode–etched Single-mode–Multimode (MESM) fiber sensor. The intensity and the wavelength sensitivities for the RI measurement in the range of 1.428-1.458 are obtained as -2308.92 %/RIU and 1313.14 nm/RIU, respectively. Finally, the MESM-SPR sensor is proposed and characterized. Results exhibit high performance in the RI range of 1.333 to 1.357, in which the sensitivity of 1433 nm/RIU is achieved. The advantages like low cost, high sensitivity, and simple fabrication methods make these sensors promising devices for chemical, food industry, and biosensing applications.

The control of air quality in museums or storages is of fundamental interest for the conservation of historic artifacts. The present work reports an example of application of RFID sensors developed in the European project SensMat and dedicated to this issue. The sensors are based on the varia-tion of property of an RFID tag coupled to a sensitive silver thin film exposed to the environment. As it will be described in the paper, such low cost sensors are interrogated by a commercial reader and provide the environmental corrosivity index and thus the presence of pollutants. The selected case study concerns the monitoring of pollution by H2S in a building dedicated to conservation and restoration of archeological and historical woods. The ability of sensors to map spatially the corrosivity within buildings is highlighted.

It is important to increase the quality of health and medicine. A wearable system for continuous monitoring of the patient is important to overcome this issue. Thus a patient with Arrhythmia due to its low cost and success in saving the life of the patient was the right option for the care partner. In addition, the device will provide a consumer with a smart smartphone application with accurate pulse beat and body temperature data in real time. MAX 30100 and LM35 are primarily used for the detection of human heart and temperature. The performance of these sensors is generated by an arrhythmia algorithm in the esp32 segment.

Wireless Sensor Networks (WSN) is the network of the resource-constrained network which forms the foundation of the Internet of Things (IoT). The Routing Protocol for Low-power and Lossy Networks (RPL) is responsible for generating and managing data routing paths. Nodes implementing RPL uses the mechanics of Objective Function (OF) to select the preferred next-hop node – parent node, and optimal routing path to the destination node. If routing decisions are not efficiently made, this results in increased collision domain, leading to packet losses and packet retransmission which impairs the network operational lifetime. In this study, we present the Contiki Operating System (OS), a state-of-the-art OS for IoTs, ContikiRPL; Contiki variant of RPL. We investigated the performance of RPL with respect to its two OFs; Objective Function Zero (OF0) and the Minimum Rank with Hysteresis Objective Function (MRHOF). The performance of these OFs was evaluated on the following metrics; Packet Delivery Ratio (PDR), Power consumption, and network latency. The result shows that MRHOF outperformed OF0 on all metrics with an overall average PDR of 91.5%, a latency of 44ms, and power consumption of 1.72mW across all nodes. This results in optimal network performance with improved network operational lifetime.

The detection of hormones, pharmaceutical and personal care products (PPCPs), in aqueous complex media as water bodies is an urgent and mandatory matter because of its harmful impact on the environment. This work presents a sensor device which is able to detect trace of the synthetic hormone 17α-ethinylestradiol (EE2), in a range of concentration of 10-15 to 10-9 M in both mineral and tap waters. These types of water were studied due to their different degrees of complexity, which allow to attain a better understanding of EE2’s behavior and response in different media. The sensor body consists of solid supports having interdigitated electrodes without and with a thin film deposited on it, and device response is evaluated through impedance spectroscopy. The thin films were prepared by the layer-by-layer technique from aqueous solutions of polyethylenimine (PEI) and poly(sodium 4-styrenesulfonate) (PSS) polyelectrolytes. Results demonstrated that it is possible to discriminate clearly the different waters used and to detect EE2, obtained from the second principal component (PC2) as a result of the application of principal component analysis method, with a sensitivity of -0.072 ± 0.009 and -0.44 ± 0.03 per decade of concentration, for mineral and tap water, respectively. Detection limits values were found to be of 8.6 fM (2.6 pg/L) and of 7.5 fM (22.2 pg/L) for TW and MW, respectively and are lower than the ones found in literature. Moreover, the achieved constant proportionality between the PC2 values for each EE2 concentration reveals that one can use this methodology to quantify EE2 concentration in unknown aqueous complex matrices.

Wireless Sensor Networks (WSNs) is considered to be a promising research area since it entails sensing capabilities. WSNs are confronted by fabricated explosion injection attacks and in return results into draining of vitality on sensor nodes routing mainly because of increased capabilities in a broad range of applications where sensor nodes use a battery as the power source. In this paper, we reveal and claim a state-of-the-art model to minimize vitality depletion of nodes within the network in return increases network period to more realistic stretch. It is revealed that the main cause is vitality consumption unbalances in different parts of the network direct resulting from having a static sink. More still, the network nodes neighboring the sink insistently partake in progressing data of other nodes to the sink. Consequently, the network nodes are supplementarily subjected to untimely vitality exhaustion. This paper mainly provides a novel movable (mobile) fuzzy logic sink approach and an intelligent system like expect systems that are able to scrutinize network situation, and make the superlative choice for spreading the network period robotically.

A Mild traumatic brain injury (mTBI) or concussion has become a public health problem in the United State. Sports and recreational activities are major sources of concussions; with the most incidents connected to American football. Recently, many companies and research institutions have started studying concussions and introduced some means of protection and some alarming systems of strong jolts. The major detection and protection system currently available on the market is the electronic helmet (e-helmet) composed of measurement devices to record head impact acceleration. The most commonly used devices in e-helmets are accelerometers to measure linear acceleration and gyroscopes for rotational/angular acceleration. Using smart textiles for concussion detection is currently uncommon and limited due to the lack of literature studying their voltage related errors. Actually, there are few works that characterize some voltage-force related errors for such type of sensors but for small impact forces and under bench testing while the behavior of those sensors was not described for higher ranges of applied forces and in field situations. This paper previews some common techniques used in e-helmets for concussion detection and highlights electronic textiles and smart fabric sensors that could be very useful for these applications. It discusses and validates the general behavior of such type of sensors under high impact forces and on field testing instead of bench testing, and also it characterizes the effect of increasing the thickness of the sensing element layer on the sensor. A custom-made pressure sensor was created of some available fabrics to be embedded within the padding of a football helmet to quantify the impacting force to the head. The sensor is mainly composed a Semi Conductive Polymer Composite SCPC layer with modifiable thickness that was modified three times with 0.2, 0.4, and 1.6mm to characterize the general behavior of the sensor due to a high amount of impacts and correlated with the thickness. A pendulum system was built to test the pressure sensors, while a special camera and an open-source video analysis software, Tracker was used to track the pendulum bob. The speed and the acceleration of the pendulum bob were measured, then the impact force was calculated and a voltage-force response was obtained. The results showed that no meaningful improvement occurs by small increase in the thickness but better sensor behavior could be obtained by significant increment to observe any difference. Despite that at a very high impacts, the suggested sensor with Velostat layers is not giving the real voltage readings that reflect the actual applied forces but it gives a helpful information that illustrate the distribution of the force through identification the place of the highest and lowest voltage readings regardless of the exact values of those readings. However, the proposed smart textile pressure sensor could be applicable in future e-helmet designs with additional research-based improvements especially on the structure of the sensing element layer to be able to withstand such high impacts which in turns improves the overall sensor performance and accurately measures pressure in concussion-inducing ranges.

Nodes in wireless sensor networks (WSN) are characterized particularly by their limited power and memory capabilities. Limited memory is an important parameter as it defines the size of the operating system and the processing code. As established previously, energy and memory efficiency is the most important evaluation factors of WSNs as they are directly related to data loss and network lifetime. However, based on our simulation results, memory efficiency determines the selection or abandon of nodes by the botmaster for the propagation of bots in an IoT infrastructure. Consequently, the node’s memory efficiency determined the spread of bots in the network and provides defense actors with an insight of the botmaster behavior for mitigation of the attack. Conventional botnet propagation and mitigation models did not consider the impact of node’s memory efficiency in the IoT platform. To address this gap, we build IoT-SIEF, a novel propagation model with forensic capability that will analyze command and control propagation behavior based on the perspective of the node’s memory efficiency. IoT-SIEF model used to explore the dynamics of propagation using numerical simulation with more than 50% outperform other models in mitigating the number of secondary bots. Consequently, it can serve as a basis for assisting the planning, design, and defense of such networks from the investigator's point of view.

Lung cancer remains the leading cancer killer worldwide. Early diagnosis can effectively increase the patient cure rate but existing diagnostic methods limit early lung cancer diagnosis. Therefore, development of a simple but efficient lung cancer screening method is important to improvement of both the diagnosis rate and the survival rate of lung cancer patients. In this study, ten photosensitive materials with high sensitivity and high specificity were screened accurately to construct a microarray sensor that can rapidly identify six types of lung cancer biomarkers in exhaled breath. Results from hierarchical cluster analysis (HCA), principal component analysis (PCA) and difference maps showed that the classification of the analytes agreed with structure similarity laws. The detection results from parallel experiments and structurally similar analytes, in turn, cluster into a group; the fingerprints of the different analytes have specific response regions. The well-screened sensor chip fabrication workload and cost were both reduced by approximately two thirds, while the microfluidic device sensitivity and stability increased by approximately 1.3 times their corresponding values before optimization. The dual-channel device also offers real-time contrast detection and synchronous parallel detection functions and has potential application prospects for use in extensive screening of high-risk populations for lung cancer.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

Pipelines are widely used for transportation of hydrocarbon fluids over millions of miles over the world. The structures of the pipelines are designed to withstand several environmental loading conditions to ensure safe and reliable distribution from point of production to the shore or distributions deport. However, leaks in pipeline networks are one of the major causes of innumerable losses in pipeline operators and nature. Incidents of pipeline failure can result in serious ecological disasters, human casualties and financial loss. In order to avoid such menace and maintain safe and reliable pipeline infrastructure, substantial research efforts have been devoted to implementing pipeline leak detection and localisation using different approaches. This paper discusses on pipelines leakage detection technologies and summarises the state-of-the-art achievements. Different leakage detection and localisation in pipeline systems are reviewed and their strengths and weaknesses are highlighted. Comparative performance analysis is performed to provide a guide in determining which leak detection method is appropriate for particular operating settings. In addition, research gaps and open issues for development of reliable pipeline leakage detection systems are discussed.

In the Korean construction industry, legal and institutional safety management improvements are continually being pursued. However, there was a 4.5% increase in the number of workers’ deaths at construction sites in 2017 compared to the previous year. Failure to wear safety helmets seems to be one of the major causes of the increase in accidents, and so it is necessary to develop technology to monitor whether or not safety helmets are being used. However, the approaches employed in existing technical studies on this issue have mainly involved the use of chinstrap sensors and have been limited to the problem of whether or not safety helmets are being worn. Meanwhile, improper wearing, such as when the chinstrap and harness fixing of the safety helmet are not properly tightened, has not been monitored. To remedy this shortcoming, a sensing safety helmet with a three-axis accelerometer sensor attached was developed in this study. Experiments were performed in which the sensing data were classified whether the safety helmet was being worn properly, not worn, or worn improperly during construction workers’ activities. The results verified that it is possible to differentiate among wearing status of the proposed safety helmet with a high accuracy of 97.0%

Ziyuan-3 (ZY-3) satellite is the first civilian stereo mapping satellite in China and was designed to achieve the 1: 50000 scale mapping for land and ocean. Rigorous sensor model (RSM) is required to build the relationship between the three-dimensional (3D) object space and two-dimensional (2D) image space of ZY-3 satellite imagery. However, each satellite sensor has its own imaging system with different physical sensor models, which increase the difficulty of geometric integration of multi-source images with different sensor models. Therefore, it is critical to generate generic model， especially rational polynomial coefficients (RPCs) of optical imagery. Recently, relatively a few researches have been conducted on RPCs generation to ZY-3 satellite. This paper proposes an approach to evaluate the performance of RPCs generation from RSM of ZY-3 imagery. Three scenarios experiments with different terrain features (such as ocean, city and grassland) are designed and conducted to comprehensively evaluate the replacement accuracies of this approach and analyze the RPCs fitting error. All the experimental results demonstrate that the proposed method achieved the encouraging accuracy of better than 1.946E-04 pixel in both x-axis direction and y-axis direction, and it indicates that the RPCs is suitable for ZY-3 imagery and can be used as a replacement for the RSM of ZY-3 imagery.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

The increased expression of β4-galactosyltransferase (β4GalT) 4 was closely associated with poor prognosis of colon cancer. Recently, we showed that the expression of the β4GalT4 gene is regulated by the 0.17 kb core promoter region containing one binding site for Specificity protein 1 (Sp1). To develop a novel screening method for anti-colon cancer drugs, two sensor cell lines having the luciferase gene under the control of two β4GalT4 gene promoters that differed in length were established from SW480 human colon cancer cells. The hGT4-0.17-sensor cells possessed the luciferase reporter driven by the 0.17 kb promoter, while the hGT4-0.3-sensor cells possessed the luciferase reporter driven by the 0.3 kb promoter containing one binding site each for colon cancer-related transcription factors including activator protein 2, E2F, caudal-related homeobox transcription factors, and Runt-related transcription factors besides Sp1. Upon treatment with mitogen-activated protein kinase inhibitor U0126, the promoter activities of the hGT4-0.3-sensor cells decreased significantly, while those of the hGT4-0.17-sensor cells unchanged. These results suggest that the responsiveness to U0126 differs between two sensor cell lines due to the different regulation of the luciferase reporters. This study provides the novel screening method for anti-colon cancer drugs by the combination of two sensor cell lines.

Automobile proving ground is important for the research of vehicles which is used for the vehicle dynamics, durability testing, braking testing, etc. However, the roads in automobile proving ground will inevitably be damaged with the extension of the service life. In most previous researches, equipment similar to laser cross-section was used to detect pavement quality, the principle of which was to reflect pavement quality by detecting road surface roughness. This method ignores the elastic deformation of the roads itself when the vehicle is traveling on it and hardly compensate for the amendment. Therefore, this article presents a new method based on force sensor to reduce the impact of elastic deformation such as wheel tyre deformation, pavement deformation, and wheel rim deformation. In which, force sensors mounted on the wheels collect the three-dimensional dynamic load of the wheel.The presented method has been tested with two sets of cobblestone road load data, and the results show that The　incentives imposed by the test vehicle on the target road are 88.3%, 91.0%, and 92.05% of the incentives imposed by the test vehicle on the standard road in three dimensions, respectively. It is clear that the proposed method has strong potential effectiveness to be applied for lose detection of the special road application.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

Current commercially available instruments for monitoring mitochondrial respiration are incapable of single cell measurements. Therefore, we developed a three-electrode, Clark-type biosensor suitable for mitochondrial respirometry in single oocytes and embryos. The biosensor was embedded in a PMMA (polymethyl methacrylate) micro-chamber to allow investigation of single oocytes/embryos immersed in up to 100 µL of respiration buffer. The micro-chamber was completely sealed to avoid oxygen exchange between the inside of the chamber and the atmosphere, while being maintained at a temperature of 38.5 ˚C to preserve cell viability. Using amperometry, the oxygen consumption of cells inside the micro-chamber was measured as a change in output current and converted to femto-mol (fmol) oxygen consumed per second based on calibrations with known buffer oxygen concentrations. The sensor measured basal cell respiration supported by endogenous substrates, respiration associated with proton leak induced by inhibition of the adenosine triphosphate (ATP) synthase (complex V) with oligomycin, and the maximal non-coupled respiratory capacity revealed by Carbonyl cyanide-4-(trifluoromethoxy)phenylhydrazone (FCCP) titration. Some potential applications of this oxygen sensor system include evaluating effects of metabolic therapies on oocyte bioenergetics, and monitoring mitochondrial function throughout oocyte maturation and blastocyst development to predict embryo viability to compliment assisted reproductive technologies

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

We attempted to apply the optoelectronic sensor entitled 'OPT101' in intensive care unit clinics, based on its optoelectronic response characteristics in near-infrared wavelength range and near-infrared spectroscopy principle. The successful novel applications in our lab include early-diagnosis and therapeutic effect tracking of thrombus, noninvasive monitoring of patients' shock severity, and fatigue evaluation. This study also expects further improvements of the detector in noninvasive clinical applications.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

The widespread proliferation of sensor nodes in the era of Internet of Things (IoT) coupled with increasing usage of wireless spectrums especially the ISM band makes it difficult to deploy real-life IoT. Currently, the cognitive radio technology enables sensor nodes communicate with each other through the licensed spectrum bands as well as the free ISM bands. Cognitive radio networks (CRSNs) are considered as a promising solution to the problem of spectrum under utilization and artificial radio spectrum scarcity. The paradigm of dynamic spectrum access allows secondary users (SUs) to utilize wireless spectrum resources which belong to primary users (PUs) with minimal interference to PUs. Due to the dynamic spectrum availability and quality, routing for SUs in multi-hop CRSNs is a challenge. In this paper, we introduce novel routing metrics that estimate both the future spectrum availability and the average transmission time with the consideration of both the global statistical spectrum usage and local instant spectrum resources. In our novel routing metrics, one retransmission is allowed and considered to reduce the probability of rerouting upon PU's arrival. Then, we propose two routing algorithms for multi-hop CRSNs. Finally, we conduct simulations, whose results show that our proposed algorithms lead to a significant performance improvement over the reference algorithm.

The textile industry plays a vital role in the global economy and faces increasing pressures related to sustainability and efficiency. Given the industry's significant environmental impact and the need for improved operational strategies, our review addresses the critical intersection of decision-making methodologies and sustainable practices. Specifically, This review aims to explore the applications of Multi-Criteria Decision-Making (MCDM) techniques within the textile supply chain to enhance operational performance and decision-making processes. Utilizing a systematic literature review method, we analyzed articles from Scopus, Web of Science, and Google Scholar, focusing on those that address MCDM applications in the textile supply chain. The findings reveal a strong emphasis on supplier selection and evaluation as determinants of competitive advantage, with significant trends toward integrating fuzzy set theory and advanced MCDM methodologies to address uncertainties. Additionally, Sustainability emerges as a core theme, emphasizing the necessity for firms to incorporate green practices into decision frameworks. The insights suggest that by adopting innovative analytical techniques, organizations can improve supplier relationships and operational efficiency.

Affective computing has emerged as a prominent technology in recent years, driven by the increasing demand for machines capable of understanding and interpreting emotions. The COVID-19 pandemic has intensified this need by reducing physical interactions and increasing reliance on digital communication, which often involves complex emotional exchanges. To enhance social interactions by identifying and addressing negative emotions, an interactive emotion-perception system based on multi-sensing interfaces and affective computing has been proposed. Integration of gesture, voice, and brainwave sensors is employed to provide users with a rich sensory experience and immersive environment. Design principles and system development processes are derived from the affinity diagram method and prototype development approach. The proposed system was constructed, and experiments were conducted with 60 participants. Interpersonal interaction scenarios were explored to understand emotional transmission mechanisms, aiming to enhance user satisfaction and positive interpersonal experiences. Data were collected through indirect observation and questionnaires, followed by evaluation and statistical analysis. Findings include: (1) The emotion-perception system enhances positive interpersonal interactions by identifying 36 distinct emotions, with overall user emotions being positive but exhibiting notable individual variations; (2) The system effectively stimulates positive emotions and strengthens interpersonal interactions, with affective computing technology fostering enjoyable emotional resonance and high-quality relationships; (3) A positive correlation was observed between semantic analysis and brainwave metrics of relaxation and concentration, showing increased concentration and enhanced positive emotional interactions during message transitions; and (4) The multi-sensing and affective computing technology provides a pleasant and relaxing emotional journey, with interactions shifting from enthusiasm to comfort, demonstrating the system’s capacity for a satisfying and enjoyable experience.

Recently, oriented external electric fields (OEEFs) have earned much attention due to the possibility of tuning the properties of electronic systems. From a theoretical perspective, one can resort to electronic structure calculations to understand how the direction and strength of OEEFs affect the properties of electronic systems. However, for multi-reference (MR) systems, calculations employing the popular Kohn-Sham density functional theory with the traditional semilocal and hybrid exchange-correlation energy functionals can yield erroneous results. Owing to its decent compromise between accuracy and efficiency for MR systems at the nanoscale (i.e., MR nanosystems), in this study, thermally-assisted-occupation density functional theory (TAO-DFT) is adopted to explore the electronic properties of n-acenes (n = 2--10), containing n linearly fused benzene rings, in OEEFs, where the OEEFs of various electric field strengths are applied along the long axes of n-acenes. According to our TAO-DFT calculations, the ground states of n-acenes in OEEFs are singlets for all the cases examined. The effect of OEEFs is shown to be significant on the vertical ionization potentials and vertical electron affinities of ground-state n-acenes with odd-number fused benzene rings. Moreover, the MR character of ground-state n-acenes in OEEFs increases with the increase of the acene length and/or the electric field strength.

This article focuses on the leader-following consensus of fuzzy fractional order singular perturbation multi-agent systems (FOSPMASs) with order in 0,2. By employing the T-S fuzzy modeling approach, a fuzzy FOSPMAS is constructed. Subsequently, a fuzzy observer-based controller is designed and the error system corresponding to each agent is derived. Through a series of equivalent transformations, the error system is decomposed into fuzzy singular fractional order systems (SFOSs). According to the admissibility of SFOSs, the consensus conditions of the fuzzy FOSPMAS are obtained based on linear matrix inequalities (LMIs) without equality constraint. Finally, the effectiveness of the criteria is verified through an RLC circuit model.

This study explores the efficacy of using EEG-based parameters to diagnose bipolar disorder. A synthetic dataset was generated, including both correctly diagnosed and misdiagnosed cases, simulating realistic clinical conditions. EEG features such as theta-alpha mean, beta band mean, and coherence measures were used to train a multi-layer perceptron (MLP) model. The model achieved a validation accuracy of 92%, demonstrating strong potential for EEG-based diagnostics. However, challenges such as standardization of electrode configurations and addressing equipment differences are crucial for broader applicability and validity of the findings in diverse clinical settings.

Proton Exchange Membrane Fuel Cell (PEMFC) is a fast-developing battery technology, and the key to its reliability and lifespan improvement lies in the accurate assessment of durability. However, the degradation mechanism of PEMFC is hard to determine and its internal parameters are highly coupled. Thus, the development of the more accurate life prediction model that meets the actual scenarios is urgent to investigate. To solve this problem, a multi-feature fusion life prediction method based on Temporal Convolutional Network-Gated Recurrent Unit (TCN-GRU) is proposed. A TCN algorithm is used as the prediction base model, and two GRU modules are included to the model to strengthen the model expression ability and improve its predictive accuracy. Two widely recognized datasets and two operating conditions are utilized for model training and prediction, respectively. Comparisons are made with single-feature parameter models in terms of Root Mean Square Error (RMSE) and Determination Coefficient (R2). The results show that the prediction accuracy of the TCN-GRU multi-feature fusion model is higher than that of the single-feature models in terms of stability and anti-interference under both operating conditions. Furthermore, with the increase of input feature parameters, the TCN-GRU model is closer to the real value, which proves once again that the proposed model can meet the accuracy requirements of the life prediction of PEMFC.

This comprehensive article explores Massive MIMO (M-MIMO) design and its associated concepts, focusing on the seamless integration requirements for Beyond 5G (B5G) and 6G networks. Addressing critical aspects such as RF chain reduction, pilot contamination, Cell-Free MIMO, and security considerations, the article delves into the intricacies of M-MIMO in the evolving landscape of B5G. Moreover, the emerging MIMO concepts in this article include AI-enabled M-MIMO three-dimensional beamforming, reconfigurable intelligent surfaces, visible light communication, and THz spectrum utilization. This review highlights challenges and open research issues, including Narrow Aperture Antenna Nodes, Plasmonic Antenna Arrays, Integrated Sensing with M-MIMO, and the application of Federated Learning in M-MIMO systems. By examining these cutting-edge developments, the article aims to contribute to advancing knowledge in the field and inspire future research directions in the exciting realm of B5G and 6G networks.

Sharing confidential information is a critical concern in today’s world. Secret sharing schemes facilitate the sharing of secrets in a way that ensures only authorized participants (shareholders) can access the secret using their allocated shares. Hierarchical secret sharing schemes (HSSSs) build upon Shamir’s scheme by organizing participants into different levels based on priority. Within HSSS, participants at each level can reconstruct the secret if a specified number, denoted as the threshold value (t), or more of them are present. Each level has a predetermined threshold value. If the number of participants falls below the threshold at any level, higher-level participants must be involved in reconstructing the secret at lower levels. Our paper proposes schemes that implement hierarchical access structures and enable the sharing of multiple secrets. Additionally, our proposed scheme includes share verification. We have analyzed potential attacks and demonstrated the scheme’s resistance against them. Through security analysis and comparison with existing schemes, we highlight the novelty and superiority of our proposed approach, contributing to advancements in secure information sharing practices.

With the development of deep learning, several Graph Neural Networks (GNN)-based approaches have been utilized for text classification. However, GNNs encounter challenges in capturing contextual text information within a document sequence. To address this, a novel text classification model RB-GAT is proposed by combining RoBERTa-BiGRU embedding and a multi-head Graph ATtention Network (GAT). First, the pre-trained RoBERTa model is exploited to learn word and text embeddings in different contexts. Second, the Bidirectional Gated Recurrent Unit (BiGRU) is employed to capture long-term dependencies and bidirectional sentence information from the text context. Next, the multi-head graph attention network is applied to analyze this information, which serves as a node feature for the document. Finally, the classification results are generated through a Softmax layer. Experimental results on three benchmark datasets demonstrate that our method can achieve an accuracy of 71.48%, 98.45%, and 80.32% on Ohsumed, R8, and MR, which is superior to the existing nine text classification approaches.

ABSTRACT Lubricants play a crucial role in reducing friction and wear between surfaces in relative motion. Engine oil, as a lubricant, is specifically designed to minimize friction and wear between the moving parts of different equipment and machinery. Engine oil blending serves the purpose of adjusting the variety of lubricants available to meet specific performance requirements. Through blending, it is possible to tailor the characteristics of the lubricating oil, such as viscosity, stability, and additive content, to optimize its effectiveness in reducing friction, protecting engine components, and enhancing overall equipment performance. By customizing lubricant formulations through blending, manufacturers can address the diverse lubrication needs of modern engines and machinery, ensuring smooth operation, longevity, and efficiency.To enhance the quality of the lubricant and achieve the desired high-performance multi-grade engine oil, a systematic approach was followed. The process began with testing the specific gravity of the oil using a hydrometer and thermometer to ensure accurate measurements. Subsequently, 5 liters of base oil were carefully measured and poured into a stainless steel reactor pot to serve as the blending vessel. Following this, 1 liter of paraffin oil (100N) was added to the base oil to introduce specific properties to the blend. To further optimize the formulation, 0.42 kg (7% of the total blend) of additives, including a selection of specific performance-enhancing compounds, was incorporated. These additives, such as Aspen, Tackifier, and other essential components like anti-wear, corrosion inhibitors, detergents, dispersants, and antioxidants, were meticulously measured and added to the mix. Through this precise blending process, the goal was to craft a high-quality multi-grade engine oil that meets the stringent performance requirements for various operating conditions and equipment types. After the melted Aspen and dissolved tackifier were added to the mixture, thorough stirring was carried out to ensure uniform distribution until a homogeneous blend was achieved. The mixture was then exposed to heat to facilitate the reaction between the base oil and additives, reaching a temperature of 70°C for optimal blending. Subsequently, 0.5 kg of viscosity index improver was introduced into the mixture and stirred continuously for a period of 5 minutes to ensure proper integration. Following this step, 5 grams of dye were carefully added to the mixture, and stirring was continued to evenly disperse the coloring agent throughout the blend. This meticulous process aimed to ensure that all components were effectively incorporated, facilitating the production of a high-quality, customized multi-grade engine oil with enhanced performance characteristics and optimal lubricating properties. After subjecting the mixture to a temperature of 70°C, the heat source was removed, allowing the product to gradually cool down to room temperature, which was estimated to be around 30°C. Following this cooling process, the product underwent a filtration step to remove any residual impurities present in the mixture. A sample of the purified product was then extracted for further analysis. Quality control tests were meticulously carried out on the sample to ensure that the product met the rigorous standards set by the Standard Organization of Nigeria (SON). The results obtained from the quality control tests were highly promising, indicating that the product indeed complied with the stringent specifications outlined by the regulatory body. This adherence to quality standards is essential in ensuring the product's reliability and performance in various applications. The successful outcome of the quality control test underscores the meticulous attention to detail and commitment to excellence in the production process. The rigorous quality control procedures implemented in the analysis of the product highlight the commitment to upholding high standards of quality and safety in the manufacturing process. By consistently meeting and exceeding industry regulations and standards, the product not only demonstrates its reliability but also reflects a dedication to customer satisfaction and product excellence. The adherence to the SON standards showcases a commitment to producing top-quality products that meet the needs and expectations of consumers and industry stakeholders alike.

The multi-objective optimization design of hydraulic climbing mechanism (the core mechanism of gantry crane) was realized by using the method of combining central composite design (CCD), Kriging and multi-objective genetic algorithm (MOGA). Firstly, the hydraulic climbing mechanism model was established and the appropriate design variables were selected. The mass, maximum deformation and maximum equivalent stress of the hydraulic climbing mechanism was taken as the optimization objectives. Through the comparative analysis of the parameters of wedge block, anchor block, anchor plate、baffle, the parameters that have the greatest impact on the optimization objectives are selected as geometric constraints. Then, according to the results of experimental design, Kriging model was used to establish the response surface optimization model of objective function. Finally, the optimal results were obtained by using MOGA method. The experimental results show that the optimization strategy is reliable, and the mass of the optimized model is reduced by 10.28%. While meeting the actual production requirements, the lightweight design of the hydraulic climbing mechanism is realized, which saves the design cost and improves the material utilization rate.

This paper focuses on improving the tracking accuracy for servo systems and increasing the contouring performance of precision machining. The dynamic friction during precision machining is analyzed using the LuGre model. The dynamic and static parameters in the friction model are efficiently and accurately identified using the improved Drosophila Swarm Algorithm based on cross-mutation. The friction tracking error can be deduced by the friction state space and an expression is derived. To compensate for the tracking error caused by friction, a feedforward compensation control is designed to avoid signal lag in traditional friction controllers. Furthermore, the factors of multi-axis parameter mismatching that impact the machining profile accuracy are analyzed for multi-axis control. An adaptive cross-coupled control-based pre-compensation strategy of contour error is designed to reduce both the tracking error and the contour error. The effectiveness of the proposed method is validated through several experiments, which demonstrate a remarkable improvement in tracking performance and contour accuracy.

The sustainable development and operation of mining enterprises as major sources of economic growth in many countries is determined by both a balance of economic, environmental, and social objectives and the resources required to achieve these objectives. Transportation is one of the main resources at open pits. It accounts for up to 70% of open pit operating expenses. Various parameters of transportation means should be coordinated both with the parameters of the open pit and meet the conditions of its operation. The problem of selecting a dump truck model in the paper is solved using a universal system of selection criteria developed using an original methodology. The two-level system of criteria includes all currently known selection criteria. The peculiarity of the methodology is the use of the multi-criteria FUCOM method for ranking the criteria. In addition, it is proposed to differentiate the criteria evaluations according to the experts' competence levels. Sets of criteria for evaluation by experts of different levels are proposed. The obtained criterion ranks are recommended to be used by managers of mining enterprises to choose a dump truck model. The presented methodology is suitable for the development of new systems of criteria, considering significant changes in operating conditions or the emergence of factors not considered in this study. Evaluation of all models of dump trucks on the market using the developed system of criteria is envisaged by the authors in a future study.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

This article deals with the queueing-inventory system, composed of c junior servers, a senior server, two finite waiting halls, and an infinite orbit. On occasion, junior servers encounter challenges during customer service. In these instances, they approach the senior server for guidance in resolving the issue. Suppose the senior server is engaged with another junior server. The approaching junior servers await their turn in a finite waiting area with a capacity of c for consultation. Concerning this, we study the performance of junior servers approaching the senior server in the retrial queueing-inventory model with the two finite waiting halls dedicated to the primary customers and the junior servers for consultation. We formulate a level-dependent QBD process and solve its steady-state probability vector using Neuts and Rao’s truncation method. The stability condition of the system is derived, and the R matrix is computed. Optimum total cost has been obtained, and sensitivity analyses, which include expected total cost, waiting time of customers in waiting hall and orbit, number of busy servers, and fraction of successful retrial rate of the model, are done numerically.

Remote distributed generation control and demand response is nowadays a basic need, especially for the Distributed Network Operators (DNOs). The integration of Renewable Energy Sources (RES) with stochastic production characteristics into the grid in conjunction with the newly appeared stochastic demand consumers (i.e., electric vehicles) hardens the ef-forts of the DNOs to keep the grid’s operation within safe limits and prevent cascading black-outs while staying in compliance with the SAIDI and SAIFI indices during maintenance and re-pair operations. Taking also under consideration the aging of the existing grid infrastructure, making it year by year more prone to failure, it is yet of great significance for the DNOs to have access to real-time feedback from grid’s infrastructure, fast, with low-cost upgrade interventions, easily deployed on the field and with fast response potential, in order to be able to perform real-time grid management (RTGM). In this article, we describe the architecture, development and deployment of a hybrid real-time control system of distributed generation (DG) units, which has the potential to be applied easily to DNO’s substations, RES plants and consumers (i.e. electric vehicles’ charging stations), that combines a low-cost minimum intervention into the electricity grid and its components and eliminates all communication interoperability problems between the different vendors’ installed electrical equipment.

Multi-cancer early detection (MCED) tests are being developed, but little is known about patient receptivity to their use for cancer screening. The current study assessed patient interest in such testing. Our team conducted a prospective, observational study among primary care patients in a large, urban health system. They were asked to complete a telephone survey that briefly described a new blood test in development to identify multiple types of cancer, but was not currently recommended or covered by insurance. The survey included items to assess respondent background characteristics, perceptions about MCED testing, and interest in having such an MCED test. We also used multivariable analyses to identify factors associated with patient interest in test use. In 2023, we surveyed 159 (32%) of 500 identified patients. Among respondents, 125 (79%) reported a high level of interest in having an MCED test. Interest was not associated with personal background characteristics, but was positively associated with the following expectations: testing would be recommended for cancer screening, be convenient, and be effective in finding early-stage disease (OR=11.70, 95% CI: 4.02, 34.04, p < 0.001). Research is needed to assess patient interest and actual uptake when detailed information on testing is presented in routine care.

The benefits of multi-robot systems are substantial, bringing gains in efficiency, quality, and cost, and are useful in a wide range of environments from warehouse automation, to agriculture, and even extend in part to entertainment. In multi-robot system research, the main focus is on ensuring efficient coordination in the operation of the robots, both in task allocation and navigation. However, much of this research seldom strays from theoretical bounds; there are many reasons for this, with the most prominent and impactful being resource limitations. This is especially true for research in areas such as multi-robot path planning (MRPP) and navigation coordination. This is a large issue in practice as many approaches are not designed with meaningful real-world implications in mind and are not scalable to large multi-robot systems. This survey aims to look into the coordination and path-planning issues and challenges faced when working with multi-robot systems, especially those using a prioritised planning approach and identify key areas which are not well-explored and the scope of applying existing MRPP approaches to real-world settings.

Building facade design plays an essential role in enhancing energy efficiency and reducing environmental impact in high-performance building design. Balancing the conflicts among various building facade design parameters to satisfy different optimization objectives constitutes a highly complex optimization problem. The rapidly increasing number of studies demonstrates a significant interest in implementing multi-objective optimization methods to tackle building facade optimization problems. This study conducts a systematic review of optimization methods for building facade optimization (BFO). The optimization objectives and design variables are categorized based on their characteristics. The efficiency and effectiveness of optimization algorithms in addressing BFO problems are compared. Building optimization techniques and tools are showcased, along with their functions and limitations. Key findings highlight the robust feasibility and effectiveness of optimization algorithms, methods, and techniques in resolving a diverse range of BFO challenges. The limitations, challenges, and future potential of these methods are summarized and proposed.

Autophagy is an evolutionarily conserved mechanism for degrading and recycling different cellular components in both normal development and stress conditions. Our recent research demonstrated that autophagy-mediated compartmental cytoplasmic deletion is essential for pollen germination. However, how autophagy regulates pollen germination to ensure its fertility remains largely unknown. Here, we applied multi-omic analyses to investigate the downstream pathways of autophagy in the process of pollen germination. Although ATG2 and ATG5 play similar roles in regulating pollen germination, high-throughput transcriptomic analysis reveals that silencing ATG5 has greater impact on the transcriptome than silencing ATG2. Cross-comparisons of transcriptome and proteome analysis reveal that gene expression at mRNA level and protein level are differentially affected by autophagy. Furthermore, high-throughput metabolomics analysis demonstrates that pathways related amino acid metabolism and aminoacyl-tRNA biosynthesis can be affected by both ATG2 and ATG5 silencing. Collectively, our multi-omic analyses reveal a central role of autophagy in cellular metabolism, which is critical for the initiation of pollen germination and the guarantee of pollen fertility.

The protein extract of Ulva australis hydrolyzed with alcalase and flavourzyme investigated multi-functional properties, including total antioxidant capacity (TAC), collagenase inhibitory and antibacterial activities. The #5 fraction (SP5) and #7 fraction (SP7) of U. australis hydrolysate from cation-exchange chromatography showed significantly high TAC, collagenase inhibitory and antibacterial effects against Propionibacterium acnes, and only Q3 fraction from anion-exchange chromatography showed high multi-functional activities. The eight peptides among 42 peptides identified by MALDI-TOF/MS and Q-TOF/MS/MS were selected from the results to screen molecular docking on target proteins, and were synthesized. Thr-Gly-Thr-Trp (TGTW) showed ABTS [2,2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)] radical scavenging activity. Effect TAC as Trolox equivalence was dependent on the concentration of TGTW. The Asn-Arg-Asp-Tyr (NRDY) and Arg-Asp-Arg-Phe (RDRF) possessing collagenase inhibitory activity increased according to the increase of concentration and the IC50 values of them were 0.95 mM and 0.84 mM, respectively. Peptides, RDRF and His-Ala-Val-Tyr (HAVY) showed anti-P. acnes effects with IC50 values of 8.57 mM and 13.23 mM, respectively. These results suggest that the U. australis hydrolysate could be a resource for the application of effective nutraceuticals and cosmetics.

As an important means of controlling the spread of cities, large-scale urban green belts have been widely used in the planning and construction of green space systems in various mega-size cities around the world. In previous studies, there has been more research on the overall isolation effect of green belts, while there has been less research on changes in their internal structure. There have been more perspectives on the land-use change (LUC) caused by urban expansion, and less systematic research on the dual driving factors of LUC. In this paper, we constructed a multi-dimensional index system to measure the "contraction-expansion" mechanism of land use in the overlapping vegetation areas of large green belts under the dual influence of urban expansion and urban greening, from the perspectives of quantity, space, and connectivity during different construction periods. Taking the boundary of two green belts in Beijing as an example, we hope to provide scientific support for the construction and ecological protection of Beijing's green belts.

Nowadays, cyber-physical systems (CPSs) are composed of more and more agents and the demand for designers to develop ever larger multi-agent systems is a fact. When the number of agents increases, several challenges related to control or communication problems arise due to the lack of scalability of existing solutions. It is important to develop tools that allow control strategies evaluation of large-scale systems. In this paper, it is considered that a CPS is a heterogeneous robot multi-agent system that cooperatively performs a formation task through a wireless network. The goal of this research is to evaluate the system's performance when the number of agents increases. To this end, two different mixed reality frameworks developed with the open-source tools Gazebo and Webots are used. These frameworks enable combining both real and virtual agents in a realistic scenario allowing scalability experiences. They also reduce the costs required when a significant number of robots operate in a real environment, as experiences can be conducted with a few real robots and a higher number of virtual robots by mimicking the real ones. Currently, the frameworks include several types of robots being the aerial robot Crazyflie 2.1 and differential mobile robots Khepera IV those used in this work. To illustrate the usage and performance of the frameworks, an event-based control strategy for rigid formations varying the number of agents is analyzed. The agents should achieve a formation defined by a set of desired Euclidean distances to their neighbors. To compare the scalability of the system in the two different tools, the following metrics have been used: formation error, CPU usage percentage, and the ratio between the real-time and the simulation time. The results show the feasibility of using Robot Operating System (ROS) 2 in distributed architectures for multi-agent systems in mixed reality experiences regardless of the number of agents and their nature. However, the two tools under study present different behaviors when the number of virtual agents grows in some of the parameters, and such discrepancies are analyzed.

Memristor has attracted a lot of interest due to its high processing speed, low power consumption and high integration ability, which is critical for electronic systems and memory-centric computing. However, the memristor programming circuit and strategy are still inflexible and complex, since the signal generator/collector and stimulate pulse must be carefully matched and designed based on memristor intrinsic characteristics without reconfigurable. Here, a simple and effective circuit only consists a parallel reference-resistor-and-NMOS is designed to program memristor with a more than 99% memristance precision. And the amplitude and width of stimulate pulse are fixed to ±4V and 5ms, respectively. In order to cope with the device variation, such as ±10% tolerance of transition voltage, an optimized programming strategy was proposed and demonstrated great robustness. Additionally, a set of reference resistors and NMOSs have been added to facilitate multi-level memristance operation without requiring any changes to the circuit structure. This program circuit was also employed to program memristor crossbar remains 99% precision. In the end, a memristor-based convolutional neural network which controlled by our optimized programming circuit was used for image recognition, and 89.36% accuracy can be achieved even under 15.8% memristance tolerance. This novel circuit demonstrates a simple and flexible strategy in memristor programming, providing a new way to control memristor crossbar for practical application.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

The link of fracture analysis of large ships is an essential part of the structural safety of ships. However, the finite element analysis of large structure according to the traditional method not only has high requirements on the computer, but also the influence of the mesh encryption at special locations makes further requirements on the accuracy of the ship. In this paper, based on the extended finite element method (XFEM) and the multi-point constraint method (MPC), the dynamic crack expansion process of the rectangular plate containing cracks under the multi-scale model is comparatively studied by using ABAQUS simulation software Finally, the applicability of the method is verified by applying the multi-scale model of ship nodes. The results show that the computational effort of the multi-scale model is significantly reduced with the same accuracy and allowable error, which proves the accuracy and efficiency of the method.

According to the Global Report on Internal Displacement (GRID, 2022), the number of displaced people worldwide at the end of 2021 was 59.1 million, with 53.2 million of them being the result of conflicts and violence, and 5.9 million caused by climate-related disasters. Furthermore, the In-ternational Organization for Migration (IOM) predicts that the climate crisis will be solely re-sponsible for one billion migrants by 2050. In this context, the research examines the issue of coastal multi-risk arising from a combination of heavy rainfall, river's overflow, and sea-level rise phenomena, analysing it through the disciplinary perspective of urban planning. Specifically, the study focuses on the need to upgrade the Local Urban Plan from a climate-proof perspective by defining a method aimed at updating the territory's cognitive framework through the preparation of a multi-risk map (which considers different time horizons), as well as the prescriptive apparatus of the Plan through the definition of a toolkit of site-specific design actions oriented towards urban adaptation. The proposed methodology is verified on the case study of Isola Sacra, Fiumicino (Italy), and it is intended to be applicable to other territorial contexts. The research aims to outline guidelines for updating urban planning tools from a climate-proof perspective to promote long-term resilient urban development in risk-prone areas.

Purpose: Emotional voice conveys important social cues that demand listeners’ attention and timely processing. This event-related potential study investigated the feasibility of a multi-feature oddball paradigm to examine adult listeners’ neural responses to detecting emotional prosody changes in non-repeating naturally spoken words. Method: Thirty-three adult listeners completed the experiment by passively listening to the words in neutral and three alternating emotions while watching a silent movie. Previous research documented pre-attentive change-detection electrophysiological responses (e.g., MMN, P3a) to emotions carried by fixed syllables or words. Given that the MMN and P3a have also been shown to reflect extraction of abstract regularities over repetitive acoustic patterns, the current study employed a multi-feature oddball paradigm to compare listeners’ MMN and P3a to emotional prosody change from neutral to angry, happy, and sad emotions delivered with hundreds of non-repeating words in a single recording session. Results: Both MMN and P3a were successfully elicited by the emotional prosodic change over the varying linguistic context. Angry prosody elicited the strongest MMN compared to happy and sad prosodies. Happy prosody elicited the strongest P3a in the centro-frontal electrodes, and angry prosody elicited the smallest P3a. Conclusions: The results demonstrated that listeners were able to extract the acoustic patterns for each emotional prosody category over constantly changing spoken words. The findings confirm the feasibility of the multi-feature oddball paradigm in investigating emotional speech processing beyond simple acoustic change detection, which may potentially be applied to pediatric and clinical populations.

Background: The first few minutes after birth are the most dangerous for the survival of an infant. Babies in neonatal intensive care units are either under heated or overheated, and hypothermic infants remain hypothermic or develop a fever. As a result, special attention must be paid to monitoring and maintaining the time of recovery from hypothermia states. Despite numerous studies, only a few have examined the transition from neonatal hypothermia and associated risk factors in depth. Method: A retrospective observational study was conducted to track axillary temperatures taken at the time of neonatal intensive care unit admission, which were then tracked every 30 minutes until the newborn's temperature stabilized. All hypothermic neonates admitted to the neonatal intensive care unit between January 2018 and December 2020 was included in the study. Temperature data were available at birth and within the first three hours of admission for 391 eligible hypothermic neonates. The effect of factors on the transition rate in different states of hypothermia was estimated using a multi-state Markov model. Result: The likelihood of progressing from mild to severe hypothermia was 5%, while the likelihood of progressing to normal was 34%. The average time spent in a severe hypothermia state was 48, 35, and 24 minutes for three different levels of birth weight, and 53, 41, and 31 minutes for low, moderate, and normal Apgar scores, respectively. Furthermore, the mean sojourn time in a severe hypothermia state was 48, 39, and 31 minutes for three different levels of high, normal, and low pulse rate, respectively. Conclusion: For hypothermic survivors within the first three hours of life, very low birth weight, low Apgar, and high pulse rate had the strongest association with hypothermia and took the longest time to improve/recover. As a result, there is an urgent need to train all levels of staff dealing with maintaining the time of recovery from neonatal hypothermia.

In this note we describe a new approach to the option pricing problem by introducing the notion of the safe (and acceptable) for the writer price of an option, in contrast to the fair price used in the Black-Scholes model. Our starting point is that the option pricing problem is closely related with the hedging problem by practical techniques. Recalling that the Black - Scholes model does not give us the price of the option but the initial value of a replicating portfolio we observe easily that has a serious disadvantage because assumes the building of this replicating portfolio continuously in time and this is a disadvantage of any model that assumes such a construction. Here we study the problem from the practical point of view concerning mainly the over the counter market. This approach is not affected by the number of the underlying assets and is particularly useful for incomplete markets. In the usual Black-Scholes or binomial or some other approaches one assumes that one can invest or borrow at the same risk free rate $r>0$ which is not true in general. Even if this is the case one can immediately observes that this risk free rate is not a universal constant but is different among different people or institutions. So, the fair price of an option is not so much fair! Moreover, the two sides are not, in general, equivalent against the risk therefore the notion of a fair price has no meaning at all. We also define a variant of the usual binomial model, by estimating safe upward and downward rates $u,d$, trying to give a cheaper safe or acceptable price for the option.

Short-term changes in shallow bathymetry affect the coastal zone and therefore their monitoring is an essential task in coastal planning projects. This study provides a novel approach for monitoring shallow bathymetry change based on drone multispectral imagery. Particularly we apply a shallow water inversion algorithm on two composite multispectral datasets being acquired five months apart in a small Mediterranean sandy embayment (Chania, Greece). Initially, we perform radiometric corrections using proprietary software and following we combine the bands from standard and multispectral cameras resulting in a six-band composite image suitable for applying the shallow water inversion algorithm. Bathymetry inversion results showed good correlation and low errors (< 0.3m) with sonar measurements collected with an uncrewed surface vehicle (USV). Bathymetry maps and true-color orthomosaics assist in identifying morphobathymetric features representing crescentic bars with rip channel systems. The temporal bathymetry and true-color data reveal important erosional and depositional patterns, which were developed under the impact of winter storms. Furthermore, bathymetric profiles show that the crescentic bar appears to migrate across and along-shore over the 5-months period. Drone-based multispectral imagery proves to be an important and cost-effective tool for shallow seafloor mapping and monitoring when it is combined with shallow water analytical models.

Marketing is the manner of how to make our sales the best in the market, our prices the most accessible, our clients satisfactory, and thus our brand is the largest distributed. This needs sophisticated and advanced understanding of the total network related. Indeed, marketing data may be seen in different forms such as qualitative and quantitative. However, in the literature, it is easily noticed that large bibliography may be collected about qualitative studies, against few studies on the quantitative point of view. This is a major drawback that makes the marketing science still focusing on the design, although the market is strongly depending on quantities such as money and time. Indeed, marketing data may be a time series such as brand sales per specified periods, brand related-prices over specified periods, market shares, ..., etc. The purpose of the present work is to investigate some marketing models based on time series due to brands. We will precisely study the effect of the time scale on the persistence of brands sales in the market and on the forecasting of such a persistence according to the characteristics of the brand and the related market competition or competitors. Our study is acted on a sample of Saudi brands during the period November 22, 2017 to December 30, 2021.

The incidence and prevalence of food allergy (FA) are increasing. While several studies have established the safety and efficacy of early introduction of single allergens in infants for the prevention of FA, the exact dose, frequency, and number of allergens that can be safely introduced to infants particularly in those at high or low risk of atopy are still unclear. This 1-year study evaluated the safety of early introduction of single foods (milk, egg, or peanut), vs. two foods (milk/egg, egg/peanut, milk/peanut), vs. multiple foods (milk/egg/peanut/cashew/almond/shrimp/walnut/wheat/fish/soy at low, medium, or high doses) vs no early introduction in infants between 4-6 months of age. At the end of the study, they were evaluated for plasma biomarkers associated with food reactivity with standardized blood tests. Two to four years after the start of the study, participants were evaluated by standardized food challenges. The serving sizes for the single, double, and low dose mixtures were 300 mg total protein per day. The serving sizes for the medium and high dose mixture was 900 mg and 3000 mg total protein, respectively. Equal parts of each protein were used for double or mixture foods. All infants were breastfed until at least 6 months of age. Results demonstrate that infants at either high or low risk for atopy were able to tolerate early introduction of multiple allergenic foods with no increases in any safety issues, including eczema, FA, or food protein induced enterocolitis. The mixtures of foods at either low, medium, or high doses demonstrated trends for improvement in food challenge reactivity and plasma biomarkers compared to single and double food introductions. The results of this study suggest that early introduction of foods, particularly simultaneous mixtures of many allergenic foods is efficacious for preventing FA and can occur safely.

Autofocus is an essential part of the SAR imaging process. Multi-subaperture autofocus algorithm is a commonly used autofocus algorithm for processing SAR stripmap mode data. The multi-subaperture autofocus algorithm has two main steps, the first is to estimate the phase error gradient within the subaperture, the second is to splice the phase error gradient, that is, to remove the shift amount between the estimated adjacent subapertures’ error gradients. Previous gradient-splicing algorithms assume that the estimation of subaperture error is accurate, but when the estimation of subaperture phase error gradients is not accurate enough, these algorithm performance will be degraded. A new phase error gradient splicing algorithm is proposed in this paper. It roughly estimates the shift amount first, and then finely estimates the shift amount based on the minimum-entropy criterion, which can improve the robustness of splicing especially when the estimation of the phase error gradients of the subaperture is not accurate enough. To speed up the algorithm, a variable-step-size search method is used. Simulation and experimental results show that the algorithm has enough accuracy and still has good performance when other splicing algorithms doesn’t perform well.

Evolutionary convergence provides natural opportunities to investigate how, when, and why novel traits evolve. Many convergent traits are complex, highlighting the importance of explicitly considering convergence at different levels of biological organization, or ‘multi‐level convergent evolution’. To investigate multi‐level convergent evolution, we propose a holistic and hierarchical framework that emphasizes breaking down traits into several functional modules. We begin by identifying long‐standing questions on the origins of complexity and the diverse evolutionary processes underlying phenotypic convergence to discuss how they can be addressed by examining convergent systems. We argue that bioluminescence, a complex trait that evolved dozens of times through either novel mechanisms or conserved toolkits, is particularly well suited for these studies. We present an updated estimate of at least 94 independent origins of bioluminescence across the tree of life, which we calculated by reviewing and summarizing all estimates of independent origins. Then, we use our framework to review the biology, chemistry, and evolution of bioluminescence, and for each biological level identify questions that arise from our systematic review. We focus on luminous organisms that use the shared luciferin substrates coelenterazine or vargulin to produce light because these organisms convergently evolved bioluminescent proteins that use the same luciferins to produce bioluminescence. Evolutionary convergence does not necessarily extend across biological levels, as exemplified by cases of conservation and disparity in biological functions, organs, cells, and molecules associated with bioluminescence systems. Investigating differences across bioluminescent organisms will address fundamental questions on predictability and contingency in convergent evolution. Lastly, we highlight unexplored areas of bioluminescence research and advances in sequencing and chemical techniques useful for developing bioluminescence as a model system for studying multi‐level convergent evolution.