Worldwide, different strategies are elaborated in order to ensure optimum conditions for the development and growth of the economic competitiveness, but also for increasing the quality of life and environment protection. All these strategies are closely linked with the development and modernization of the systems for producing energy from clean and renewable sources. In this context, the present paper presents the results of the researches regarding the evaluation of the sustainability of the briquettes production, using the biomass resulted from vine winter pruning as raw material. An analysis of the scientific references indicates that nearly 8 Mt of biomass result from over 7.4 million hectares of vine plantations existent worldwide, biomass that could be valorized through densification in order to produce solid biofuels with a lower calorific value of more than 17 MJ·kg-1. When designing the scientific endeavor, the following aspects were considered: defining the aim and objectives of the research; design of the research algorithm; collection, preparation and conditioning of the biomass; chemical analysis of the briquettes; evaluation of the technological characteristics of the briquettes; evaluation of the energy consumption and energy efficiency for producing the briquettes, taking into account two drying methods (natural and artificial drying). In the meantime, some specific laboratory equipment was design and built for the artificial drying of biomass, evaluation of the mechanical durability, measurement of the energy consumption etc. The analysis of the experimental data has led to the conclusion that the agricultural waste from vine pruning can constitute an important and sustainable source of energy in the form of bri-quettes, which fulfill most of the requirements imposed by the international standards.

Soil quality is a factor which is directly related to the sustainability of agricultural production and can be compromised through the use of inadequate management practices. In this work, soil edaphic respiration and changes in microbial biomass promoted by cover crops in an integrated crop-livestock system (ICLS) were evaluated using soil quality indicators by the respirometry method. The design used was completely randomized in a 3x6 factorial scheme and multivariate principal components analysis (PCA) was performed according to MANOVA. The edaphic respiration was determined based on the respirometry technique. From the results, it was found that edaphic soil respiration was significant in the nine evaluation periods, demonstrating the importance of grass cover on this edaphic respiration arising from the biological activity of microorganisms, which is directly related to the amount of organic carbon in the soil. It was concluded that the use of cover crops contributed to producing organic matter in the soil and consequently greater microbial respiratory activity.

The ubiquitous nature of polymers have led to a widespread demand for sustainable polymers in numerous industrial applications. However, lack of well laid out guidelines, product development pathways and certifications have resulted in a lot of commotions and confusions within the polymer value chain. Herein, a meticulous review is conducted on the topic of polymer sustainability shedding light on the standards, product declarations, biobased-biomass concepts, product carbon footprint etc. It is critical that companies significantly contribute on such sustainability efforts in lieu of market readiness and competitive advantages. Any discussion within the sustainability horizon references a couple of terms/ abbreviations/concepts. In this article, such key terminologies and concepts related to polymer sustainability are reviewed with a holistic outlook on the widespread approaches within the polymer sustainability horizon.

Biomass-derived carbon dots (CDs) are gaining much interest in recent times as it is a sustainable option with abundant availability, low cost, and tunable luminescence. Herein, we report a simple green synthesis method to produce highly fluorescent CDs from Eucalyptus globulus leaves using the one-pot hydrothermal approach. The fabricated CDs exhibit strong blue fluorescence with an excitation and emission maxima of 340 nm and 442 nm respectively. The highest quantum yield (QY) obtained was 60.7%. Due to its promising optical properties and biocompatibility, CDs can be a potential candidate for biosensing applications. Moreover, we employed a life cycle assessment (LCA) cradle-to-gate approach to study the environmental impacts of the synthesis strategy used for the fabrication of CDs. The results point out that citric acid is a main hotspot in CDs synthesis, regarding environmental impacts in most categories. This justifies the introduction of biomass, which reduces the amount of citric acid, thus leading to a more sustainable synthesis strategy for fabricating CDs.

The adoption of sustainable forest management practices emerged as a contemporary imperative for forest biodiversity preservation, functional integrity, and mitigation of climate change. Within the spectrum of these practices, thinning is recognized as an environmentally sustainable strategy. The primary objective of thinning is the equitable redistribution of aboveground growth, diverting resources from younger trees to promote the accelerated development of more valuable specimens compared to unthinned forests. Thinning, while fostering aboveground changes, induces substantial alterations in soil chemical and biochemical properties. This review addresses the often-debated consequences of thinning on soil characteristics, focusing on the intricate interplay involving different thinning intensities and their impact on soil chemical and biochemical parameters. Specifically, the analysis delves into the modulation of organic carbon levels, microbial biomass, and enzymes crucial to the organic matter cycle. Two key aspects are scrutinized: firstly, the influence of thinning intensity and the temporal dimension post-thinning on soil properties; secondly, the comparative impact of thinning intensity versus the time elapsed from the thinning event on soil properties and associated biological processes. The findings underscore pivotal insights: a) temporal dynamics significantly affect soil organic matter across broadleaved (excluding beech), coniferous, and mixed forests, manifesting as early as 2-7 years post-thinning; b) thinning intensity, up to a threshold of 50%, enhances soil quality by augmenting organic carbon content, bolstering microbial communities, and amplifying associated enzyme activities. This review consolidates valuable information for forest managers, providing guidance to optimize natural processes in tandem with achieving specific management objectives. By illuminating the nuanced interactions between thinning practices and soil dynamics, this knowledge equips stakeholders to make informed decisions in the pursuit of sustainable forest management and ecological resilience.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Hydrogen is increasingly recognized as a crucial element in the shift toward sustainable energy systems due to its high energy density and minimal environmental impact. Biomass, a renewable material derived from plants and animals, presents a promising feedstock for hydrogen production, offering both environmental and economic benefits. This paper examines diverse biomass resources for hydrogen production, including agricultural and forest residues, dedicated energy crops, and organic waste. It reviews key technologies for converting biomass to hydrogen, categorized into thermochemical, biochemical, and hybrid processes. Thermochemical methods like gasification and pyrolysis are discussed for their ability to handle varied feedstocks and produce high-purity hydrogen. Biochemical processes, such as anaerobic digestion and dark fermentation, are analyzed for their efficiency and lower operational costs. Hybrid approaches, which integrate multiple technologies, are explored for their potential to enhance system performance. Industrial applications of biomass-derived hydrogen are highlighted, including its use in transportation, power generation, the chemical industry, and heating. Future perspectives emphasize the need for advanced catalysts, process integration, sustainable feedstock sourcing, and supportive policies to drive commercial viability. The paper concludes by highlighting biomass’s significant promise in advancing sustainable energy systems and achieving global energy security and environmental goals.

Puerto Rico's geographic and climatic conditions render it highly susceptible to natural disasters, particularly hurricanes. The devastation caused by Hurricane Maria in 2017 highlighted the fragility of the island's centralized energy infrastructure, which led to prolonged power outages and severe disruptions in essential services. This review explores the potential of biomass energy to enhance resilience in post-disaster scenarios, focusing on Puerto Rico as a case study. Biomass energy, derived from organic materials like agricultural residues, woody biomass, and municipal solid waste, offers a renewable and locally sourced power solution that can be rapidly deployed. Key biomass conversion technologies, including direct combustion, gasification, anaerobic digestion, and pyrolysis, are examined for their applicability and benefits in emergency energy provision. The implementation of biomass-powered microgrids in Puerto Rico, such as those by Casa Pueblo and Arensis, demonstrates the feasibility and effectiveness of decentralized energy systems in disaster recovery. These microgrids provide reliable power to critical infrastructure, reduce dependence on fossil fuels, and support waste management efforts. The review also discusses ongoing research and development in advanced biomass technologies, such as second-generation biofuels, algae-based biomass, and biomass-to-hydrogen conversion, which can further enhance energy efficiency and sustainability. Additionally, the economic, environmental, and social impacts of biomass energy are evaluated, highlighting its role in job creation, waste reduction, emission control, and community resilience. Policy recommendations include streamlining permitting processes, enhancing financial incentives, developing feedstock supply chains, and incorporating biomass into disaster recovery plans. The findings suggest that integrating biomass energy into Puerto Rico’s energy strategy can significantly improve its capacity to respond to and recover from natural disasters, promoting long-term sustainability and resilience.

The status of tropical fisheries is poorly known because the existing methodological choices have variable outcomes and recommendations. Therefore, multiple approaches to estimating sustainability were compared, namely fisheries independent stock biomass and recovery rates, fisheries dependent landed catches, balanced harvest and gear use metrics, and fish length measurements. Unfished biomass recovery time series was established by a 45-year stock recovery relationship from 7 fisheries reserves and compared to catch and length-based estimates of sustainability. The logistic production rates (r = 0.10 ± 0.06 95% CI) and maximum equilibrium total biomass (150 ± 30 tons/km²) indicated a broad range of potential maximum sustainable yields but likely ranging from 1.1 to 3.9 (95% CI; mean = 3.8) tons/km²/year. In contrast, mean annual biomass growth rates in reserves was lower but less variable than surplus production estimates, ranging from 2.1 to 3.5 (mean=2.8 tons/km²/year). Realized catches at landing sites was lower still, ranging from 1.43 to 1.52 (mean=1.48± 0.2 tons/km²/y). Differences were largely attributable to changes in taxonomic composition and an imbalance in the proportionality of production potential versus actual capture rates. Differences in the vulnerability of taxa to fishing and a lack of compensatory increased production among fishing resistant taxa could largely account for the lost potential production. Large proportional losses of catch were measured among snappers, unicorn fish, sweetlips, goatfish, and soldierfish, while smaller proportional gains in the catch were found among resident herbivorous rabbitfish, parrotfish, and groupers. Many of these declining taxa had vulnerable schooling life histories likely to require special habitat and reserve characteristics. Evaluations of sustainability from length measurements found 17 or 7% of total and 12% of caught species had a minimum sufficient sample sizes (>30 individuals, 413 catches, 2299 individuals, and 144 species) to evaluate length and spawning metrics of sustainability. Seven of these species met length-based and 3 meet spawning potential ratio thresholds for sustainability. Consequently, length-based evaluations were unable to evaluate the sustainability of the larger community. Recommendations include a management focus on the recovery of “ghost taxa”, species abundant in the oldest reserve but not contributing to fisheries yields.

Bioenergy with carbon capture and sequestration (BECCS) is one strategy to remove CO2 from the atmosphere. To assess the potential scale and cost of CO2 sequestration from BECCS in the US, this analysis models carbon efficiencies and costs of biomass production, delivery, power generation, and CO2 capture and sequestration in saline formations. The analysis includes two biomass supply scenarios (near-term and long-term), two biomass logistics scenarios (conventional and pelletized), two generation technologies (pulverized combustion and integrated gasification combined cycle), and three cost accounting scenarios (gross cost, net cost after electricity revenues, and net cost after electricity revenues with avoided emissions from conventional power generation). Results show cost Mg-1 CO2 as a function of CO2 sequestered (simulating capture up to 90% of total CO2 sequestration potential) and associated spatial distribution of resources and generation locations for the array of scenario options. Under a near-term scenario using 222 million Mg yr-1 of biomass, up to 196 million Mg CO2 can be sequestered at scenario-average costs ranging from $60 to $158 Mg 1 CO2; under a long-term scenario using 823 million Mg yr-1 of biomass, up to 727 million Mg CO2 yr 1 can be sequestered at scenario-average costs ranging from $32 to $242 Mg-1 CO2. These costs are largely influenced by cost accounting scenario, and the CO2 sequestration potential may be reduced if future competing demand reduces resource availability. Results suggest there are multiple feedstock-logistics-generation pathways toward CO2 drawdown that could be incrementally trialed and monitored for environmental sustainability effects. Interactive visualization of results is available at [final link to be determined].

In terms of sustainability, there is a pressing need to evaluate agricultural and forestry leafy biomass that has no current economic value or may pose a threat to the environment. In this aspect, leafy biomass, which represents around 5% of the total tree, can be used for purposes that would be more profitable and ecofriendly. To this end, biorefinery of leafy biomass in the way of extracting valuable health compounds such as phenolics would ensure a valuable societal health ingredient besides alleviating waste disposal problem. However, during the biorefinery process, the primary challenges start with ensuring the feedstock to produce phenol rich leaves extract followed by their isolation and commercialization of this leaves extract. This current review aims to detail the types of biomasses, biorefinery approach of leafy biomass towards the phenolic extraction, leaves commercialization followed by the marketing strategy of the application of phenol rich leaves extract. The outcome of this overview will serve researchers and relevant industries in understanding the process for feedstock collection and the suitable sectors to apply leafy biomass derived healthy compounds.

The carbon stocks in the forests originated from the atmosphere and are accumulated in the organic matter of trees and soils. Forests play major roles in providing ecosystem services like climate change mitigation through carbon sequestration and nutrient flow dynamics. Therefore, the major objective of this study was to estimate carbon stocks of Biteyu forest by quantifying the aboveground biomass of trees, belowground carbon, soil carbon, and carbon stocks of litter pool. Systematic sampling technique was employed for vegetation and carbon data collection. The total of 10 line transects were laid along elevational gradients. The transects were 500 m apart and sampling plots were 300 m apart from each other. Each transect has comprised of a minimum of 4 plots to a maximum of six totaling 50 plots representing the forest for the investigation. A square sample plot of 900 m2 was used to collect vegetation data with a DBH ≥ 2.5 cm and a height of 2 m and above. To sample herbaceous vegetation in the forest floor, five smaller subplots of 1 m x 1 m = 1 m2 (four at the corner and one at the centre of the main plot) were established. The disturbance level was also determined using the cattle interference and selective cutting of trees. The appropriate allometric models were applied for both aboveground and belowground biomass estimations. The findings showed that cattle interference affects the forest understory from growing and recruitment. The mean of cattle interference was 4.77±2.12 per ha and the mean of wood stump was 26.67±9.37 per ha. The size class analysis showed that the smallest diameter class (2.5-10 cm) in the forests represented 37.05% of the total stem density. The diameter classes between 10 and 30 cm comprised a stem density of 41.08%. It was estimated that the total carbon stock of Biteyu forest was about 166.67 ± 16.4 ha-1. The carbon stock in AGB and BGB was estimated to be 87.13 ± 11.80 t ha-1 and 22.94 ± 2.84 t ha-1, respectively. Moreover, the contribution of soil and litter carbon pools to the total carbon in the forest ecosystem were 56.37 ± 1.73 and 0.26 ± 0.01 t ha-1 , respectively. From the present study it can be concluded that estimated mean carbon stock of the forest is smaller than that of other similar forests in the dry evergreen montane forest, which was attributed to the higher anthropogenic disturbances. Therefore, the interventions, which reduce the climate change effect, would be very important in the maintenance of forest ecosystem functioning.

This paper presents new above-ground biomass (AGB) and biomass components equations for seventeen forest species in the temperate forests of northwestern Mexico. A data set corresponding to 1336 destructively sampled oak and pine trees was used to fit the models. Generalized method of moments was used to simultaneously fit systems of equations for biomass components and AGB, to ensure additivity. Additionally, the carbon content of each tree component was calculated by the dry combustion method, in a TOC analyser. The fitted equations accounted for on average 91, 83, 84 and 78% of the observed variance in stem wood and stem bark, branch and foliage biomass, respectively, whereas the total AGB equations explained on average 93% of the total observed variance in AGB. The inclusion of h or d²h as additional predictor in the d-only based equations systems slightly improved estimates of stem wood, stem bark and total above-ground biomass, and greatly improved the estimates produced by the branch and foliage biomass equations. The fitted equations were used to estimate AGB stocks at stand level from a database on growing stock from 429 permanent sampling plots. Three machine-learning techniques were used to model the estimated stand level AGB and carbon contents; the selected models were applied to map the AGB and carbon distributions in the study area, which yielded mean values of 129.84 Mg ha^-1 and 63.80 Mg ha^-1, respectively.

Global energy scenario is becoming vital for the sustainable economic development of a region or country. Current changes in energy production, mainly due to scarcity and geopolitical factors, have proven the need for changes in energy mix towards a lower energy dependence. In that sense, a considerable amount of biomass waste is generated in many regions, because of agro-industrial activities, whose management could contribute to energy production. The aim of this work was to study the determination of combustion conditions in a biomass stove by using different raw materials as fuels, such as pine, poplar, and plum tree pellets. For that purpose, power, excess air, and biomass content were optimized, among other parameters, and fumes were analyzed with a Testo 335 analyzer, recording temperatures with temperature probes. As a conclusion, high yields were found for the optimized parameters of the studied biomass (ranging from 91.1 % for poplar pellet to 92.34 % for pine pellet), making these three biomass fuels suitable for combustion in the abovementioned stove. Also, increasing biomass flow by 25 % in the stove contributed to a higher efficiency of the process, especially in the case of plum tree pellets.

Carbon sequestration is associated with plant biomass and soils. The amount of carbon sequestration in the Atewa Range Forest Reserve (ARFR) is affected by varied anthropogenic activities like logging, mining and farming. This study estimate the above and below ground carbon stock and assess human-induced stress impacts on the Highly Stressed Vegetation (HSV), Moderately Stressed Vegetation (MSV), and Non-Stressed Vegetation (NSV) in the ARFR. The above ground biomass of trees was determined using the allometric model of (Henry, et al., 2010) whereas plants root biomass was calculated using Cairns et al. (1997). Soil organic carbon was determined using the Walkley–Black method. We observed that carbon stock was higher in the above-ground than the below-ground component. The MSV, recorded the highest stock of carbon followed by the NSV and the HSV whilst sequestrated carbon stocks was generally high and varied across the three stress levels. Within the forest, the intensity of anthropogenic activities has negatively impacted the amounts of carbon sequestrated at various levels.

Chronic Obstructive Pulmonary Disease (COPD) is a disease characterized by local and systemic inflammation independently of the risk factor; during the exacerbations, such inflammation is accentuated and amplified. A practical inflammatory marker and one with an applicable predictive value in the follow-up has been sought. FeNO has shown an excellent performance in that respect within the context of asthma and has also been studied in tobacco-smoke COPD (COPD-TS). In Biomass-smoke COPD (COPD-BS), this, to our knowledge, has not been evaluated. Objective: To measure FeNO levels in patients with COPD-BS and to compare these with those of patients with stable COPD-TS and in healthy controls. Methods: Transversal, observational, descriptive, comparative, and analytical study. A total of 57 patients, including 23 with COPD-BS, 17 with COPD-TS, and 17 healthy control subjects. The measurement of FeNO was carried out on all of these by means of the on-line chemiluminescence technique; the values were expressed in parts per billion (ppb) for their analysis. Results: It was observed that the FeNO values were similar between COPD-BS and COPD-TS and were significantly different between the healthy and stable COPD (both groups). No correlation was found between pulmonary function and symptoms with FeNO in any of the groups. Conclusions: The level of FeNO in stable COPD is found to be increased in a similar manner in COPD-BS and COPD-TS, with a significant difference on comparing it with that of the healthy subjects.

Herein we report the expansion of the chemical space available from the chitin, accessible via the biogenic N-platforms 3A5AF, M4A2C and di-HAF. The biologically active heteroaromatics furo[3,2-d]pyrimidin-4-one and furo[3,2-d]pyrimidin-4-amine can be selectively accessed from 3A5AF and M4A2C, respectively. The chiral pool synthon di-HAF is a viable substrate for the Achmatowicz rearrangement, providing streamlined access to 2-aminosugars possessing a versatile hydroxymethyl group at C5.

Mining activities could produce a large volume of spoils, waste rocks, and tailings, which are usually deposited at the surface and become sources of metal pollution. Phytostabilization of the mine spoils could limit the spread of these heavy metals. Phytostabilization can be enhanced by using soil amendments like manure-based biochar capable of immobilizing metal(loid)s when combined with plant species that are tolerant of high levels of contaminants while simultaneously improving properties of mine soils. However, the use of manure-based biochar and other organic amendments for mine spoil remediation are still unclear. In this greenhouse study, we evaluated the interactive effect of biochar application and compost on shoots biomass yield (SBY), roots biomass yield (RBY), uptake, and bioconcentration factor (BCF) of Zn and Cd in corn (Zea mays L.) grown in mine soil. Biochar sources (BS) consisted of beef cattle manure (BCM); poultry litter (PL); and lodge pole pine (LPP) were applied at 0, 2.5, and 5.0% (w/w) in combination with different rates (0, 2.5, and 5.0%, w/w) of cattle manure compost (CMC), respectively. Shoots and roots uptake of Cd and Zn were significantly affected by BS, CMC, and the interaction of BS and CMC. Corn plants that received 2.5% PL and 2.5% BCM had the greatest Cd and Zn shoot uptake, respectively. Corn plants with 5% BCM had the greatest Cd and Zn root uptake. When averaged across BS, the greatest BCF for Cd in the shoot of 92.3 was from the application BCM and the least BCF was from the application of PL (72.8). Our results suggest that incorporation of biochar enhanced phytostabilization of Cd and Zn with concentrations of water-soluble Cd and Zn lowest in soils amended with both manure-based biochars while improving biomass productivity of corn. Overall, phytostabilization technique and biochar application have the potential to be combined in the remediation of heavy metals polluted soils.

Stand biomass in boreal forests has attained recognition for its crucial role in carbon cycling. In this study, we examined the effect of stand age on above- and belowground biomass allocation in downy birch (Betula pubescens Ehrh.) in three drained peatland sites in Central Finland. We used allometric equations to estimate individual-tree above-ground biomass and its various components, including stem wood, stem bark, living branches, leaves, and dead branches. The above-ground biomass ranged from 10.5 t ha-1 to 276.0 t ha-1 and foliage biomass from 0.009 t ha-1 to 0.6 t ha-1. We found that stand age had a strong correlation with above-ground biomass, but foliage biomass appeared to peak at the middle-aged (50 years) stand compared to the young (10 years) or mature (80 years) stands. We observed coarse root biomass production of 45, 250, and 110 g m-2 in the 0–50 cm peat layer for young, middle-aged, and mature stands, respectively. Most coarse root biomass occurred in the top 20-cm layer (77%). These findings improve our understanding of how biomass allocation patterns – specifically those in foliar biomass– change over time, and the impact on litter inputs into the soil.

Background: The possibility of nutrient composition design in biomass of invertebrates is studied. The results may be used for gaining the particular nutrient concentration in biomass used for food products or medicine purposes. Methods: Two model species of terrestrial invertebrates, such as the House cricket Acheta domesticus (Linnaeus, 1758) and the earthworm Eisenia fetida (Savigny, 1826), within the variation of feeding substrate, are studied in this paper. Results: It is stated that in crickets and earthworms similar tendencies of B-vitamin content increase occur for those vitamins where their initial level was high. A double dose of the vitamin enrichment of food substrate leads to increasing of vitamin C, fat-soluble vitamins and the major part of B-vitamins content. In a control group of crickets a level of vitamin C was 1.5 times lower than in a control group of earthworms. After the enrichment of feeding substrate, the level of vitamin C in biomass of crickets has not changed, but within the earthworms it has significantly increased. The content of a multiple range of minerals have not changed after a singular dose enrichment, but some microelements, such as Pb and Se, have significantly decreased in earthworms after a double dose enrichment of feeding substrate. The calorific value of crickets is twice higher than the earthworms one and it has not significantly changed after a double dose substrate enrichment. Conclusions: It is revealed that the content of vitamins in the biomass of model species can be controlled within the feeding substrate enrichment.

Bifunctional catalysts consisting of mono- or bimetallic nanoparticles (NPs) and zeolite supports received considerable attention due to excellent catalytic properties in numerous reactions including direct and indirect biomass processing. Here, we discuss major approaches to the preparation of NPs in zeolites, concentrating on methods allowing the best interplay (synergy) between metal and acid sites which is normally achieved for small NPs well-distributed through zeolite. We focus on modification of zeolites to provide structural integrity and controlled acidity which can be accomplished by incorporation of certain metal ions or elements. The other modification avenue is the adjustment of the zeolite morphology including creation of numerous defects for the NP entrapment and designed porosity. In this review we also provide examples of synergy between metal and acid sites and emphasize that without density functional theory calculations many assumptions about interactions between active sites stay unvalidated. Finally, we describe the most interesting examples of direct and indirect biomass (waste) processing for the last five years.

For the effective utilization of rice husk, organosolv fractionation was investigated to separate three main components (glucan, xylose, and lignin) with low acid concentration. Reaction temperatures of 170–190 °C, ethanol concentrations of 50–70% (v/v), and sulfuric acid concentrations of 0–0.7% (w/v) were investigated, with the reaction time and liquid-to-solid ratio kept constant at 60 min and 10, respectively. The fractionation conditions for the efficient separation into the three components of rice husk were determined to be 180 °C, 60% (v/v) of ethanol, and 0.25% (w/v) of sulfuric acid. Under these fractionation conditions, 86.8% of the xylan and 77.5% of the lignin were removed from the rice husk, and xylose and lignin were obtained from the liquid in 67.6% and 49.8% yields, respectively. The glucan digestibility of the fractionated rice husk was 85.2% with an enzyme loading of 15 FPU (filter paper unit) of cellulase per g-glucan.

A E. Crassipes is considered a problem in different aquatic ecosystems, due to its abundance could become a solution to design and build economic and efficient treatment plants, and especially for the production of biofuels such as bioethanol. The objective of this research is to design and implement a sustainable development process between phytoremediation and bioethanol production with E. crassipes, evaluating the incidence of chromium adhered to the biomass of this plant in the production of bioethanol. Materials and methods: A system was installed to evaluate the phytoremediation with E crassipes with water loaded with chromium, determining the effectiveness of this plant to remove this heavy metal even if it is alive in a body of water. After this process, we proceeded to bring the biomass loaded with chromium to bioreactors to evaluate the production of bioethanol, assessing three types of biomass, one without chromium adhered and the other two with chromium adhered to its plant structure. There was an impact of the ethanol production of the E crassipes due to the presence of chromium, but this production can be taken into account for the assembly of an integral system of phytoremediation and bioethanol production, making the most of this biomass.

This research demonstrates the optimization and production of biochar from barley husk (BH), corn cob (CC), and Agave salmiana leaves (AL) via pyrolysis in a muffle furnace. Taguchi experimental design (L9) was applied to conduct the experiments at different levels by altering four operating parameters. Carbonization temperature (300–500 ºC), carbonization time (30–90 min), precursor mass (2–5 g) and N₂ flow rate (100–200 cc/min) were the variables examined in this study. The effect of the parameters on the biochar yield was investigated, and the important parameters were identified employing analysis of variance (ANOVA). The optimum conditions for maximum biochar yield were: carbonization temperature of 400 ºC, carbonization time of 30 min, precursor mass of 2 g, and N₂ flow rate of 150 cc/min. The biochars produced under optimum conditions was characterized physically and chemically. Biochar yields of 19.75% for corn cob (CCB), 32.88% for barley husk (BHB), and 31.14% for agave leaves (ALB) were obtained.

Variable retention harvesting (VRH) was designed for timber purposes and biodiversity conservation in natural forests. This system was globally tested, but few studies are related to soil microbial components. The objective was to evaluate different retention types (aggregated and dispersed retention) considering different years-after-harvesting (6, 9, 16 YAH) on soil microbial community attributes compared with unmanaged primary forests (PF) in Nothofagus pumilio forests of Tierra del Fuego (Argentina). We also evaluated the influence of climate, soil and understory vegetation. Results showed that aggregated retention increased microbial biomass carbon (MBC), microbial biomass nitrogen (MBN) and soil basal respiration (SBR) compared to dispersed retention, but with similar values than PF. However, harvested areas decreased MBC:MBN values compared with PF. We found an overall decreasing of microbial biomass and activity in 9 YAH stands, with a positive recovery at 16 YAH. Soil pH, mean annual temperature and understory vegetation cover showed a positive relationship with MBC, MBN, and SBR. The recovery after 16 YAH reaching to a different microbial community. Therefore, maintenance of retention components in managed stands for longer periods is needed. Our results highlight some advantages of VRH as a tool for conservation of forest-dwelling soil microorganisms (microbial biomass and activity).

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

Forests play an important role in reducing greenhouse gases in the atmosphere, thereby mitigating the impact of climate change. Estimating the accumulated biomass in a forest ecosystem is important for assessing the productivity and sustainability of the forest. Allometric models for above ground biomass (AGB) are linear regression equations based on the relationships between biomass and diameter at breast height (DBH), tree height (H), and/or wood density. This study estimates AGB in the Colo-I-Suva Forest Park by applying the allometry of Chave et al (2005) and the diameter: height ratio derived from Payton & Weaver (2011) for height estimation in a plot of 20

Biobutanol is becoming more relevant as a promising alternative biofuel, primarily due to its advantageous characteristics. These include a higher energy content and density compared to traditional biofuels, as well as its ability to mix effectively with gasoline, further enhancing its viability as a potential replacement. A viable strategy for attaining carbon neutrality, reducing reliance on fossil fuels, and utilizing sustainable and renewable resources is the use of biomass to produce biobutanol. Lignocellulosic materials have gained widespread recognition as highly suitable feedstocks for the synthesis of butanol, together with various value-added byproducts. The successful generation of biobutanol hinges on three crucial factors: effective feedstock pretreatment, the choice of fermentation techniques, and the subsequent enhancement of the produced butanol. While biobutanol holds promise as an alternative biofuel, it is important to acknowledge certain drawbacks associated with its production and utilization. One significant limitation is the relatively high cost of production compared to other biofuels, additionally, the current reliance on lignocellulosic feedstocks necessitates significant advancements in pretreatment and bioconversion technologies to enhance overall process efficiency. Furthermore, the limited availability of biobutanol-compatible infrastructure, such as distribution and storage systems, poses a barrier to its widespread adoption. Addressing these drawbacks is crucial for maximizing the potential benefits of biobutanol as a sustainable fuel source. This document presents an extensive review encompassing the historical development of biobutanol production and explores emerging trends in the field.

Biomass can be converted into energy/fuel by different techniques, such as pyrolysis, gasification, and others. In the case of pyrolysis, biomass can be converted into a crude bio-oil around 50-75% yield. However, the direct use of this crude bio-oil is impractical due to its high content of oxygenated compounds, which provide inferior properties compared to those of fossil-derived bio-oil, such as petroleum. Consequently, bio-oil needs to be upgraded by physical processes (filtration, emulsification, among others) and/or chemical processes (esterification, cracking, HDO, among others). In contrast, HDO can effectively increase the calorific value and improve the acidity and viscosity of bio-oils through reaction pathways such as cracking, decarbonylation, decarboxylation, hydrocracking, hydrodeoxygenation and hydrogenation where catalysts play a crucial role. This article first focuses on the general aspects of biomass, subsequent bio-oil production, its properties, and the various methods of upgrading pyrolytic bio-oil to improve its calorific value, pH, viscosity, degree of deoxygenation (DOD), and other attributes. Secondly, particular emphasis is placed on the process of converting model molecules and bio-oil via HDO using catalysts based on nickel and nickel combined with other active elements. Through these phases, readers can gain a deeper understanding of the HDO process and the reaction mechanisms involved. Finally, the different equipment used to obtain an improved HDO product from bio-oil is discussed, providing valuable insights for the practical application of this reaction in pyrolysis bio-oil production.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Welcome to the world of bioethanol revolution, in response to the soaring global energy demand, the production of bioethanol has taken center stage, captivating the attention of governments, academia, and the private sector alike. Over the years, research in this field has witnessed exponential growth, paving the way for sustainable energy production. Ethanol, the front-runner in renewable energy, can be derived from a plethora of sources. In this abstract, we will explore the exciting advancements and emerging trends in the production of bioethanol, shedding light on the promising future of sustainable energy. Bioethanol production presents a cost-effective solution by utilizing the abundance of agricultural resources. These resources serve as the foundation for producing bioethanol from various biomass sources. In this context, we evaluate the raw materials used, including sucrose-based, starchy-based, and perennial grasses. By exploring these options, we can gain a comprehensive understanding of the diverse range of agricultural feedstocks that contribute to the production of bioethanol, this paper delves into the multiple processes involved in the production of bioethanol from agricultural base biomass, unveiling a range of possibilities for harnessing renewable energy. The key steps that were thoroughly examined include pretreatment, which encompasses both physical and chemical methods, hydrolysis, direct fermentation, and saccharification. These steps serve as crucial components in the overall bioethanol production process from agricultural base biomass. By understanding and optimizing each of these stages, we can unlock the full potential of sustainable energy generation. The paper goes beyond exploring the production processes and delves into the different generations of bioethanol, each with its unique components. Additionally, it provides a comprehensive overview of the composition of agricultural and forest residues, shedding light on their potential as valuable resources for bioethanol production. Moreover, it highlights the significance of the agricultural sector in Nigeria's economy, emphasizing the importance of energy for enhancing productivity and efficiency. The integration of bioethanol as an energy source has the potential to propel this sector forward, fostering sustainable development and contributing to the overall growth of the Nigerian economy. By harnessing the power of bioethanol, Nigeria can tap into its energy potential, promoting energy utilization and creating a positive impact on various industries.

In Nigeria, the adoption of sustainable biomass for energy generation is on the rise. One crucial factor that affects the efficiency of Biomass utilization is the moisture content. This study investigates the economic impact of moisture at different stages of the wood biomass distribution chain, considering the entire chain. The methodology employed includes a comprehensive literature review, interviews, and economic calculations. By analyzing these factors, this research aims to provide valuable insights into the economics of moisture in wood biomass, contributing to the sustainable development of the Biomass energy sector in Nigeria. Based on the outcomes of this investigation, it has been discovered that the costs associated with moisture content in Nigeria amount to approximately ₦500,000,00 (Five Hundred Thousand Naira only). Utilizing wood Biomass with a moisture content of 32% weight, as opposed to 18% weight, has proven to be more costly. Transportation contributes to a significant portion of this increase, while the reduction in burning efficiency accounts for the remaining half. To further elaborate on these findings, it is crucial to understand that the transportation costs are impacted by the additional weight and volume of biomass with higher moisture content. This necessitates the use of more fuel and resources during transportation, resulting in increased expenses. Additionally, the decreased burning efficiency associated with higher moisture content poses a challenge. It leads to reduced energy output and increased fuel consumption, ultimately impacting the overall economic viability of wood biomass as an energy source. By identifying these factors, this study aims to provide insights into the economic implications of moisture content in the wood biomass distribution chain in Nigeria. These findings can serve as a basis for developing strategies to optimize the use of biomass, reduce costs, and enhance the sustainability of the energy generation process. One of the most convenient and cost-effective solutions to reduce transportation expenses and improve combustion efficiency is through planned air drying of wood biomass. Large-scale power plants typically prefer utilizing wood biomass that has undergone air drying, resulting in a moisture content ranging from 18% to 36% by weight. By implementing planned air-drying techniques, the moisture content of wood biomass can be significantly reduced, thereby decreasing transportation costs. As the biomass becomes lighter and less bulky, transportation requirements are optimized, leading to enhanced efficiency and reduced expenses. Moreover, air-dried wood biomass offers improved combustion characteristics. The reduced moisture content allows for better heat transfer during the combustion process, resulting in higher energy output and increased fuel efficiency. This not only improves the overall economics of utilizing wood biomass but also contributes to a more sustainable and environmentally friendly energy generation system. The application of planned air drying in the wood biomass distribution chain in Nigeria can serve as a practical solution to address the economic challenges associated with moisture content. By adopting this approach, stakeholders can maximize the potential of wood biomass as a renewable energy resource while minimizing costs and promoting sustainable practices.

Wood and plants are made of fibers which contain, in addition to cellulose, lignin and hemicelluloses. Xylan and galactoglucomannan are the dominant secondary cell wall hemicelluloses. Besides fibers’ traditional use in textile and paper industries, the fibers are important materials for the biorefinery industry and for developing biocomposites. In the former context, renewable lignocellulosic biomass is used as feedstock to sustainably produce fuels, chemicals, and polymers. On the other hand, in relation to composites, cellulose fibers which are anisotropic play an important reinforcing role in fiber-matrix interactions. However, for these and other applications, structural analysis of the fibers is important and among many analytical techniques used, Raman spectroscopy is one of the methods. However, given the structural similarity between hemicelluloses and cellulose, many of their Raman contributions overlap. While the wavenumber positions corresponding to the Raman contributions of cellulose, hemicelluloses, and lignin are known, extent to which overlapping features of hemicellulose modify the spectrum of cellulose is not yet fully understood. The present investigation focuses on this aspect by using xylan as one of the hemicelluloses. As a model system, samples with various mass ratios of microcrystalline cellulose (cotton) and xylan (birch wood) were prepared and analyzed by FT-Raman spectroscopy. The findings were then applied to interpret Raman spectra of selected xylan containing delignified plant fibers. It is hoped that insights gained would lead to better interpretation of the spectra of natural and treated plant materials.

Currently, in a context of biorefinery and bioeconomy, lignocellulosic biomass is increasingly used to produce biofuels, biochemicals and value-added products. Microwaves and ultrasounds are emerging techniques that enable efficient and environmentally more sustainable routes in the transformation of lignocellulosic biomass. This review is divided into four parts. In Part I, the theoretical foundations of microwaves and ultrasounds are revisited. Dielectric constants for biomass, factors that influence pre-treatment, are some of the subjects addressed. In Part II, the effects that these technologies have on lignocellulosic biomass (on the size and surface area of the particle; on the content of lignin, hemicellulose and cellulose; on the crystallinity index of cellulose; on the effect of solubilization of organic matter; on hydrolysis and reduction of sugars) are analyzed. In Part III, emphasis is given on how microwaves and ultrasounds can contribute to the achievement of value-added products. In this context, several examples of liquefactions and extractions are presented. Part IV describes examples of sonocatalysis of lignocellulosic biomass to obtain value-added products such as for instancethe production of furfural, which is significantly reduced by ultrasound.

Calicotome villosa is a eurioic legume with broad distribution in the south of Europe. It can grow in almost any type of soils as well as in humid and dry and nutrient deficient ecosystems. The broad distribution and eurioic nature of C. villosa may be attributed to its ability to establish symbiotic associations with plant growth promoting (PGP) bacteria housed in the nodules and rootless. This study examined legume-microbe symbiosis of C. villosa growing in two contrasted locations, hill top with high sun irradiance and drought; and a valley bottom, with low level or radiation and sufficient soil humidity for plant growth. Calicotome villosa adult plants established symbiotic in-teractions with bacteria in six genera, Pseudomonas, Stenotrophomonas, Bacillus, Paenibacillus, Brevicacterium and Rhizobium as well as one uncultured bacteria. Plants growing in the hill top had associated lower bacterial richness than those grown at the valley bottom. All strains were drought tolerant and produced siderophores, IAA, HCN and NH3 that stimulated plant performance in both, C. villosa plants and other four legumes commonly present in the understory of the shrubs communities The legumes’ capacity to selectively host symbiotic bacteria that enhance plant survival in harsh conditions partly accounts for the diverse partnerships between C. villosa plants and their symbionts, ultimately explaining the wide distribution of this plant species.

Disposing pollutants into water sources has posed risks to human health and the environment, and biosorption has emerged as an eco-friendly, cost-effective, and green alternative for wastewater treatment. This work shows banana peel powder (BPP) biosorbents for efficient sorption of methylene blue (MB), atrazine, and glyphosate pollutants. The biosorbent highlights several surface chemical functional groups and morphology containing agglomerated microsized particles and microporous structures. BPP showed 66% elimination of MB in 60 min, with an adsorption capacity (qe) of ~33 mg g-1, where a combination of film diffusion and chemisorption governed the sorption process. Besides, the biosorbent removed 91% and 97% of atrazine and glyphosate pesticides after 120 min, with qe of 3.26 and 3.02 mg g-1, respectively. The glyphosate and atrazine uptake best followed the Elovich and pseudo-first-order kinetic, respectively, revealing different sorption mechanisms. Our results suggest that BPP are low-cost biomaterials for green and environmentally friendly wastewater treatment.

Research Highlights: (1) Reed canary grass (RCG) is analysed in Sweden compared to willow and poplar for 2001-2020 (2) Each crop presents a different land-use and climatic profile (3) Average yield records of reed canary grass are similar to willow and poplar (4) There are divergences between trial-based and commercial yields (5) Existing LUC patterns suggest meadow>RCG and RCG>cereal (6) RCG land area is very sensitive to policy incentives. Background and objectives: RCG is an alternative crop for biomass-to-energy due to high yield and frost tolerance. We assess the cultivation in Sweden by using an extensive compilation of data, with emphasis on the extension of the cultivation, areas planted, climatic profile, land use patterns and yield levels. Material and methods: All RCG plantations are analysed for 2001-2020. A geostatistical analysis is performed to characterize where is cultivated and the land uses associated. Climatic, productivity and yield profiles are compared to willow and poplar plantations, from experiments and from commercial plantations. Results: The results show that the cultivation of reed canary grass expanded after 2005, with a maximum of 800 ha in 2009 to then decrease to the current levels of about 550 ha. It is mainly grown in colder climatic areas, with lower agricultural productivity than willow and poplar. Mean yields from trials are 6 odt ha-1 yr-1; commercial yields are 3.5 odt ha-1 yr-1. RCG replace meadow land and is replaced by cereals, when abandoned. Conclusions: Reed canary grass is an interesting alternative, growing on colder areas but on similar yield levels than other energy crops. The cultivation is more sensitive to policy incentives

This study spatially estimates degraded lands in Indonesia that have limited functions for food production, carbon storage, and conservation of biodiversity and native vegetation, and examines their suitability to grow biodiesel species (Calophyllum inophyllum, Pongamia pinnata and Reutealis trisperma) and biomass species (Calliandra calothyrsus and Gliricidia sepium). Results showed that Indonesia has ∼3.5 million ha of degraded lands potentially suitable for these species. With the all-five-species scenario, these lands had the potential to produce 1105 PJ yr⁻¹ of biomass and 3 PJ yr⁻¹ of biodiesel. With the biodiesel-only-species scenario, these lands showed the potential to produce 10 PJ yr⁻¹ of biodiesel. Despite this energy potential, however, the land sizes were too small to support economies of scale for biofuel production. The study findings contribute to identifying lands with limited functions, modeling biofuel-species growth on regional lands and estimating carbon stocks of restored degraded lands in Indonesia.

Carbohydrate composition of lignocellulosic biomass is one of the main factors for production of biofuel from the plant biomass. Various methods like Thermogravimetric analysis (TGA), near infrared spectroscopy (NIR) often used in determination of polysaccharide component of the plant biomass. However, used of such tools is based on the prediction and very costly. This paper discussed about the determination of carbohydrate composition (cellulose, hemicellulose and lignin) using the automatic fibre estimation system. The protocol was developed for the estimation of cellulose, hemicellulose and lignin component of lignocellulosic biomass. This protocol explains a simple method to estimate the polysaccharide component of lignocellulosic biomass. This protocol can be used not only lignocellulosic biomass but also for other hardwood biomass. The advantages and techniques, procedures are presented below.

This study investigated the physical and combustion properties of briquettes produced from agricultural wastes (groundnut shells and corn cobs), wood residues (Anogeissus leiocarpus) and admixtures of the particles at 15%, 20% and 25% starch levels (binder). A 6 x 3 factorial experiments in a Completely Randomized Design (CRD) was adopted for the study. The briquettes produced were analyzed for density, volatile matter, ash content, fixed carbon and specific heat of combustion. The result revealed that the density ranged from 0.44g/cm³ to 0.53g/cm³, while briquettes produced from groundnut shells had the highest (0.53g/cm³) significant mean density. Mean volatile matter and ash content of the briquettes ranged from 24.35% to 34.95% and 3.37% to 4.91%. A. leiocarpus and corn cobs particles had the lowest and highest ash content respectively. The briquette fixed carbon and specific heat of combustion ranged from 61.68% to 68.97% and 7362kca/kg to 8222kca/kg respectively. Briquette produced from A. leiocarpus particles had the highest specific heat of combustion. In general, briquettes produced from A. leiocarpus particles and admixture of groundnut shell and A. leiocarpus particles at 25% starch level had better quality in terms of density and combustion properties and thus suitable as environmentally friendly alternative energy source.

The case for demand-driven research and development has received important considerations among governments, donors and programme implementing partners in development planning and implementation. Addressing demand is believed to be a bottom-top approach for designing and responding to development priorities and is good for achieving development outcomes. In this paper, we discuss the concept and application of demand driven research for development (DDRD) in Africa. We use evidence of six projects implemented under the BiomassWeb Project in Africa. We focus on parameters on level of engagement of stakeholders - whose demand is being articulated, the processes for demand articulation, capacity building and implementation processes, innovativeness of the project, reporting and sustainability of the project. We find that the nature of the institutions involved in articulation and implementation of demand-driven research and development projects and their partnerships influence the impact and reporting of demand-driven projects.

At the time of tillage, properties of the soil change, thereby changing the conditions of crop development and ultimately their productivity and quality. The effect of non-inversion tillage or no till on faba bean development is stills not widely investigated. For this reason, investigations of tillage systems from deep and shallow ploughing, chiselling, disking to no tillage were tested in Vytautas Magnus University, Agriculture Academy, Lithuania. The results showed that different tillage methods had less influence on faba bean development than meteorological conditions during the growing seasons. Soil chiselling generally showed better faba bean canopy development rates than other treatments. Faba bean roots developed somewhat better in not tilled plots. Vegetative conditions had a significant influence on faba bean development indicators. The effects of vegetative conditions during all four years of the experimentation were significantly different from each other. This shows that, due to rapid climate change, the conditions of each vegetative season become unique and require precise attention.

The effects of reaction temperature, reaction time, heating rate, nitrogen flow rate and catalyst quality on the oil yield and oxygen content in the oil were investigated by using the single factor principle. Too high and too low reaction temperature, nitrogen flow rate, heating rate and reaction time have improved the yield of bio-oil, but the oxygen content in bio-oil is higher. The reduction of catalytic dose is beneficial to the increase of oil yield but not conducive to the increase of aromatic compound content. The optimal reaction conditions were observed as reaction temperature of 500℃, nitrogen flow rate of 110 mL/min, heating rate of 20℃/min, reaction time of 15min, mass ratio of catalyst to coconut coat powder was 1, and the oil yield was 4.97%, aquatic yield was 35.80%, and solid yield was 30.78%. The gas yield was 28.45%, the oxygen content was 10.3%, and the aromatic compound content was 89.7%.The analysis of catalytic cracking mechanism shows that most of the oxygen-containing compounds in the bio-oil are generated into water and aromatic compounds by catalytic cracking reaction at high temperature, thus removing oxygen.

The research focuses on the production of particleboards from the biomass of energetic willow (Salix viminalis L.) and energetic poplar (Populus spp.), aiming to explore their feasibility as sustainable materials for various applications. Energetic willow and energetic poplar are known for their rapid growth and suitability for energy production. They present an intriguing alternative as raw materials with added value for particleboard manufacturing. The study investigates the selected mechanical and physical properties of the produced particleboards, considering parameters such as density profile, bending strength, modulus of elasticity, water absorption, thickness swelling, and screw withdrawal resistance. During the research, the results were also compared between different mass shares of willow and poplar particles in the particleboards. The findings underscore the promising potential of willow and poplar-based particleboards as eco-friendly alternatives in the construction and furniture industries, contributing to resource efficiency and carbon emission reduction efforts.

The Brazilian Pantanal region suffers intensely from biomass burning during the dry season. Large quantities of gases and particles are emitted into the atmosphere during this period, with serious implications for fauna and flora. Understanding the dynamics of these emissions is es-sential for mitigating the ecosystem, its functioning, and possible anthropogenic disturbances. In this sense, this study analyzed emissions over the north of the Brazilian Pantanal during the 2022 drought. Measurements of concentration of fine particulate matter (PM2.5), Black carbon (BC), and elemental concentration (25 chemical elements) were determined by gravimetry, reflectance analysis, and X-ray fluorescence, respectively, for samples collected between August and Octo-ber 2022. The average concentrations of PM2.5 and BC had their values increased by approxi-mately 4 and 2.5 times, respectively, when compared to the averages from a decade ago. The maximum concentrations found are close to values typical of the southern Amazon region, a re-gion with high rates of deforestation and changes in land use. The elemental analysis showed large changes in concentrations, mainly associated with biomass burning emission (BB) and soil resuspension. Furthermore, analyses of lead (Pb) concentrations showed strong anthropization at the study site.

AbstraIncorporating knowledge of indigenous forage legumes or associated nutritional attributes in cultivated pastures has the potential to improve grazing conditions, rangeland conditions, and cattle productivity. Climate change and other site-specific factors such as land sizes and other grazing management practices play a significant role in food security, job creation, and environmental health. Several research results have reported that the utilization of forage legumes in most farming systems has proved to increase herbage yield and soil fertility. The major aim of this review is to elucidate the potential benefits of intercropping indigenous forage legumes such as cowpea (Vigna unguiculacta L.Walp) and Dolichols (Lablab purpureaus) intercropped with Chloris gayana, this is to assesses the principal advantages, productivity, and overall performance of forage legumes grown in conjunction with grasses. Moreover, this review seeks to provide insights into the optimal management practices for intercropping forage legumes with grasses. The promising feature of intercropping South African pastoral systems must target the ability of forage legumes in terms of performance and utilization of agro-symbiotic relationships of N2 fixation symbiotic relationship in pastures. Moreover, this review aims also to address this knowledge gap by assessing the effects of defoliation frequency on the biomass production of selected forage legumes when intercropped with Chloris gayana in different growing seasons. By examining how varying defoliation frequencies influence biomass production, this review aimed to provide practical recommendations for optimizing forage management practices and promoting sustainable forage production systems. Through this investigation, we can gain insights into the complex dynamics between the defoliation frequency, intercropping systems, and biomass production.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

The utilization of lignocellulosic biomass as an alternative energy source presents a promising opportunity to achieve a future energy system that is clean and free from CO2 emissions. To realize this potential, it is crucial to develop effective techniques for converting biomass and organic solid waste into secondary energy sources. Among the available options, hydrogen production stands out due to its numerous advantages, including its cleanliness, versatility in conversion and utilization technologies, high energy efficiency, and dense energy content per unit weight. This article offers a comprehensive overview of different conversion pathways and important technologies for generating hydrogen from biomass and organic solid waste. It specifically focuses on the thermochemical conversion process, which shows promise as an economically viable approach. While certain thermochemical conversion processes are still in the developmental phase, utilizing organic biomass for hydrogen production is widely recommended due to its ability to yield higher amounts of end products and its compatibility with existing facilities. However, it should be noted that this method necessitates a substantial amount of energy due to its endothermic nature. The article also explores alternative hydrogen conversion technologies and their potential for utilizing organic biomass as a feedstock, while addressing the challenges and limitations associated with these methods.

In the context of climate change, the need for stakeholders to contribute to achieving SDG2 is no longer in doubt especially in sub-Saharan Africa. In this study of the landscape within 10 km of the Donomadé model farm, southeastern Togo, we sought to assess vegetation health in ecosystems and agrosystems, including their capacity to produce biomass for agroecological practices. Sentinel-2 sensor data from 2015, 2017, 2020, and 2022 were preprocessed and used to calculate normalized vegetation fire ratio index (NBR), vegetation fire severity index (dNBR), and CASA-SEBAL models. From these different analyses, it was found that vegetation stress increased across the landscape depending on the year of the time series. We estimated that 9952.215 ha, 10,397.43 ha, and 9854.90 ha were highly stressed in 2015, 2017, and 2020, respectively. Analysis of the level of interannual severity revealed the existence of highly photosynthetic areas which had experienced stress. These areas, which were likely to have been subjected to agricultural practices, were estimated to be 8704.871 ha (dNBR2017–2015), 8253.17 ha (dNBR2020–2017), and 7513.93 ha (dNBR2022–2020). In 2022, the total available biomass estimated by remote sensing for was 3,741,715 ± 119.26 kgC/ha/y. The annual average was 3401.55 ± 119.26 kgC/ha/y. In contrast, the total area of healthy vegetation was estimated to be 4594.43 ha, 4301.30 ha, and 4320.85 ha, in 2015, 2017, and 2022, respectively. The acceptance threshold of the net primary productivity (NPP) of the study area was 96%. The coefficient of skewness (0.81 ± 0.073) indicated a mosaic landscape. Productive and functional ecosystem components were present, but these were highly dispersed. These findings suggest a great opportunity to promote agroecological practices. Mulching may be an excellent technique for enhancing overall ecosystem services as targeted by the SDGs, by means of reconversion of plant biomass consumed by vegetation fires or slash-and-burn agricultural practices.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

Due to pollution and environmental deterioration, man needed to find other alternatives as energy sources, including biomass. (1) Background: The present research was conducted to evaluate the sugarcane cutting residue; this type of biomass has no use and can be burned to obtain energy. (2) Methods: Through the elaboration of pellets and, in turn, reduce the environmental impact of flora and fauna in crops, for the characterization, the raw material was subjected for the first time to physical treatment such as cleaning, drying, grinding, and sieving so that have the optimal characteristics to be used in the pelleting stage. Then a proximal analysis was conducted based on the ASTM -3172-89 Standard and the determination of the calorific value using the ASTM D-240 Standard. Likewise, the pellets were analyzed in their final stage. This method analyzes the parameters of moisture content, volatile material, ashes, and fixed carbon. (3) Results: It was obtained as a result that for the raw material, the % H=3.543, %MV=86.53, %Cz=6.939, %Cf= 2.987 and Pc= 15.702 KJ/Kg; and for the elaboration of the pellets it was carried out using the mixing proportion, 53% SAR with 47% binder, this was determined using the proximal analysis and the determination of the calorific value, from which the results of % H=5,768 were obtained., %MV=82.313, %Cz=6.376, %Cf= 5.543 and Pc= 15.635 KJ/Kg. (4) Conclusions: In other words, sugarcane cutting residues meet the physicochemical properties to be used as raw material in producing solid biofuel.

NH4Cl is one of the nitrogen sources for microalgal cultivation. However, excessive amounts of NH4Cl affects microalgal physiology and biomass contents. In this study, the effects of ammonium on microalgal growth and TAG content in the green microalga (Chlamydomonas reinhardtii) was investigated. Microalgal growth and TAG content under photoautotrophic conditions were found to be unchanged with 17 mM of ammonium, while this compound interfered with microalgal growth and induced TAG content under mixotrophic conditions with acetate supplementation. This suggested that ammonium could induce TAG production when acetate occurred in microalgal cultivation. Further, the effects of two different concentrations of NH4Cl (17 mM and 60 mM) on the cells under mixotrophic conditions were investigated. The results showed that both concentrations reduced microalgal growth, but induced total lipid and TAG content, especially after a 4-day cultivation. The oxygen evolution and Fv/Fm ratio showed that both concentrations completely inhibited the oxygen evolution on Day 4. The 60 mM NH4Cl reduced the Fv/Fm ratio from 0.7 to 0.48 indicating that ammonium supplementation directly affects the microalgae photosynthesis performance. A total of 1782 proteins were successfully identified using proteomics analysis. Among them, there were nine overexpressed proteins and four proteins were underexpressed. Using the protein–ligand interaction analysis, nitrogen metabolism is involved under NH4Cl conditions. This information can provide biochemical knowledge for microalgae development for sustainable energy usage.

The introduction of organic and inorganic substances to the environment is a result of human activities such as agriculture, domestic and industrial wastewater which leads to pollution. Treatment processes of these wastewaters are being conducted globally to eliminate easily settled materials and recover nutrients in an attempt to release clear and apparently clean effluent into natural waters. Lack of removing inorganic nitrogen and phosphorus nutrients is the greatest cause of eutrophication in water bodies which inhibits the life of other organisms as well as pose a threat to human life and loss of the economy. Different technologies have been applied and are being developed to recover nutrients as well as heavy metals from wastewater to meet the permissible limits before discharging effluents. Wastewater treatment using microalgae offers an opportunity to provide tertiary bio-treatment and production of valuable biomass. Microalgae use the available inorganic nitrogen and phosphorus for their growth which are then harvested for various uses. Additionally, they have the ability to remove heavy metals and some toxic compounds. The main specific microalgae species in this study is the Chlorella sorokiniana with the Aequorea victoria jellyfish This paper reviews some of the wastewater treatment processes and focus on the use of microalgae and some of the shortcomings of the technologies and how they can be improved to achieve maximum nutrient recovery economically with low energy demand.

In this research, the feasibility of using bottom ashes generated by the combustion of biomass (olive pruning and pine pruning) as a source of aluminosilicates (OPBA) has been studied, replacing the metakaolin precursor (MK) in different proportions (0, 25, 50, 75 and 100 wt. % substitution) for the synthesis of geopolymers. As alkaline activator an 8 M NaOH solution and a Na2SiO3 have been used. The geopolymers were cured 24 hours in a climatic chamber at 60 ° C in a water-saturated atmosphere, subsequently demoulded and cured at room temperature for 28 days. The results indicated that the incorporation of OPBA waste, which have 19.7 wt. % of Ca, modifies the characteristics of the products formed after alkaline activation. In general terms, the incorporation of increasing amounts of calcium-rich ashes results in geopolymers with higher bulk density. The compressive strength increases with the addition of up to 50 wt. % of OPBA with respect to the control geopolymers, contributing the composition of the residue to the acquisition of a better behaviour mechanical. The results indicate the potential use of these OPBA waste as raw material to produce unconventional cements with 28-day curing strengths greater than 10 MPa, and thermal conductivities less than 0.35 W/mK.

In the upgrading of biomass pyrolysis vapors to hydrocarbons, dehydration accomplishes a primary objective of removing oxygen and acidic zeolites represent promising catalysts for dehydration reaction. Here, we utilize density functional theory calculations to estimate adsorption energetics and intrinsic kinetics of alcohol dehydration over H-ZSM-5, H-BEA, and H-AEL zeolites. ONIOM calculations of adsorption energies were observed to be inconsistent when benchmarked against QM/Hartree-Fock and periodic boundary condition calculations. However, reaction coordinate calculations of adsorbed species and transition states were consistent across all levels considered. Comparison of ethanol, iso-propanol (IPA), and tert-amyl alcohol (TAA) over these three zeolites allowed for a detailed examination of how confinement impacts reaction mechanisms and kinetics. TAA, seen to proceed via a carbocationic mechanism, was found to have the lowest activation barrier, followed by IPA and then ethanol, both of which dehydrate via a concerted mechanism. Barriers in H-BEA were consistently found to be lower than in H-ZSM-5 and H-AEL, attributed to late transition states and either elevated strain or inaccurately estimating long-range electrostatic interactions in H-AEL, respectively. Molecular dynamics simulations revealed that the diffusivity of these three alcohols in H-ZSM-5 are significantly overestimated by Knudsen diffusion, which will complicate experimental efforts to develop a kinetic model for catalytic fast pyrolysis.

Common buckwheat (Fagopyrum esculentum Moench) is an annual spring-emerging crop that is classified among dicotyledons, yet due to the manner of its cultivation, use, and chemical composition of seeds. The use of buckwheat straw for energy purposes, for example, for the production of second generation bioethanol might enable its wider application and increase the cost-effectiveness of tillage. In this study, we examined the usability of buckwheat straw for the production of bioethanol. We pretreated the raw material with using ionic liquids and subsequently performed enzymatic hydrolysis and alcoholic fermentation. The obtained chemometric data was analyzed using the Partial Least Squares (PLS) regression model. PLS regression in combination with the spectral analysis within near-infrared (NIR) spectrum allowed for the rapid determination of amount of cellulose in the raw material and also provided information on the changes taking place in its structure. According to our results, we obtained good results for the combination of 1-ethyl-3-methylimidazolium acetate as the ionic liquid and Cellic CTec2 and the enzymatic preparation for the pretreatment of buckwheat straw. The highest concentration of glucose following 72 hours of enzymatic hydrolysis was found to be around 5.5 g/dm3. The highest concentration of ethanol (3.31 g/dm3) was obtained with the combination of 1-butyl-3-methylimidazolium acetate for the pretreatment and the cellulase from Trichoderma reesei for enzymatic hydrolysis. In summary, the efficiency of the fermentation process is strictly associated with the pool of available fermenting sugars, and it depends on the type of ionic liquid used during the pretreatment and on the enzymatic preparation. It is possible to obtain bioethanol from buckwheat straw using ionic liquid for the pretreatment of the raw material prior to the enzymatic hydrolysis and alcoholic fermentation of the material.

This review analyzes the synthesis and characterization of biomass-derived carbons for adsorption of emerging contaminants from water. The study begins with the definition and different types of emerging contaminants more often founded in water streams and the different technologies available for their removal including adsorption. It also describes the biomass sources that could be used for the synthesis of biochars and activated carbons. The characterization of the adsorbents and the different approaches that could be employed for the study of the adsorption processes are also detailed. Finally, the work reviews in detail some studies of the literature focused on the adsorption of emerging contaminants on biochars and activated carbons synthesized from biomass precursors.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Assessing the economic supply of biomass in a geospatial context while accounting for risk from natural disasters was studied. Risk levels were estimated from a component of factors which included: population density, road density, federal ownership, U.S. Environmental Protection Agency ecoregions, and Presidential Disaster Declarations. The Presidential Disaster Declarations included risks due to: coastal storm, drought, fire, flood, freezing, hurricane, mud land slide, severe ices, severe storms, snow, tornado, and tropical storm. Presidential Disaster Declarations included summaries based on a short-term time period from 2000-2011, and on a long-term time period from 1964-2011. Risk categories were developed as a function of the number of disaster declarations, agricultural-to-forest land ratio, average road density, and average population density. A significant contribution of the research was the allocation of spatially explicit data using GIS technology at the 5-digit zip code tabulation area. The average area for 5-digit ZCTAs in the Eastern U.S. study region was approximately 169 kilometers². Long-term risk (1964-2011) from disaster declarations had a greater impact on the economic availability of biomass supply relative to short-term declarations (2000-2011). The greatest risk to biomass supply came from population density relative to the other risk factors studies. Of the 25,044 total ZCTAs, 12,256 ZCTAs were in locations that did not include population density ≥ 150/km², road density ≥ 14 km/km², federal ownership, and US Environmental Protection Agency Level III ecoregions. Of the remaining 12,256 ZCTAs, 26.8% were considered to be moderate-to-high risk based on short-term declarations (2000-2011) and 29.4% were considered to be moderate-to-high risk based on long-term declarations (1964-2011). Lower risk locations for procuring biomass supply for both short-term and long-term declarations, across all risk factors, were in southern Georgia, South Carolina, and Texas.

Malaysia generates significant quantities of Oil Palm Wastes (OPW) which can be potentially valorised into sustainable bioenergy as envisaged by the National Biomass Strategy (NBS-2020). Despite significant investments, policy directives and government support, the valorisation of OPW into bioenergy has remained low exacerbating waste management challenges. Therefore, the strategies and impediments to the rapid bioenergy development and bioelectricity generation from OPW require practical assessment. Therefore, this paper examines the level of development and diffusion of the biomass innovation system in Malaysia based on the Functions of Innovations Systems (FIS) approach developed by Dutch and Swedish researchers. Furthermore, the key factors hindering biomass energy technologies implementation in Malaysia and potential solutions were identified, highlighted and examined. Based on the FIS analysis the functions; entrepreneurial activities, knowledge development, and resources mobilization functions are well established in the Malaysian biomass innovation system (BIS). However, the functions of guidance of search; creation of legitimacy; knowledge diffusion and market formation are underdeveloped resulting in the low penetration of bioenergy in Malaysia. Other factors include; fossil fuel subsidies, numerous or conflicting energy policies and weak collaboration between academia and the industry. The outlined challenges can be addressed by revising fuel subsidies, Feed-in tariffs, RETs implementation, roles of supervisory agencies, and bureaucratic procedures for access to funds for research and development of bioenergy in Malaysia.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

The assessment of biomass carbon stocks was conducted at plot scale as a sample to estimate for all vegetation areas by using destructive sampling and or allometric equation method. Remote sensing is one of the techniques can be used to estimate and mapping biomass carbon stock for the entire areas. The objectives of the study are the identification and determine the range of electromagnetic wave of Landsat 8 satellite data that most suitable for assessing and mapping biomass carbon stock distribution. This research analyses exponential regression equation between spectral radiance values (Lλi) for with biomass measurement results on the field to find the best correlation based on the coefficient of determination value (R2). It also analyses the relationship between field biomass and NDVI value (Normal Differences Vegetation Index) from satellite data. The study area consists of 54.9% bush (Bs), 24.5% scrub (Sc), 16.8% secondary forest (Sf), while the rest (3.8%) is a water body. The with average biomass carbon stock value 4.11 tons.ha-1, 64.43 tons.ha-1, and 85.36 tons.ha-1, for strata Sc, Bs, and Sf respectively. Spectral radiance of SWIR (Shortwave Infra-Red) band 6 is determined as a spectral characteristic that can be used to estimating carbon stock with following the equation Y= 12657(EXP(-0.642(Lλband6)) with r2 = 0.75. Correlation NDVI and field biomass showed the low r2 value (0.08), so in this study, NDVI cannot be used to estimate the biomass carbon stock.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Historical forest management practices in the southwestern US have left forests prone to high intensity, stand-replacement fires. Effective management to reduce the cost and impact of forest-fire management and allow fires to burn freely without negative impact depends on detailed knowledge of stand composition, in particular, above-ground biomass (AGB). Lidar-based modeling techniques provide opportunities to reduce costs and increase ability of managers to monitor AGB and other forest metrics. Using Bayesian Model Averaging (BMA), we develop a regionally applicable lidar-based statistical model for Ponderosa pine and mixed conifer forest systems of the southwestern USA, using previously collected field data. The selected regional model includes a mid and low canopy height metric, a canopy cover, and height distribution term. It explains 72% of the variability in field estimates of AGB, and the RMSE of the two independent validation data sets are 23.25 and 32.82 Mg/ha. The regional model developed is structured in accordance with previously described models fit to local data, and performs equivalently to models designed for smaller scale application. Developing regional models for broad scale application provides a cost-effective, robust approach for managers to monitor and plan adaptively at the landscape scale.

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

We live in the world that is completely entangled on energy and thus, Humankind can no longer do without it, power. With electricity being the main form of energy today, this has increased the complexity of our life today. In Uganda, electricity generation is mainly through hydropower which put the country in the bottleneck of over dependence on one source of energy. Yet, there are many energy systems out there that country can diversify its electricity generation. Therefore, the need to understand, the level of development and utilization of various energy systems has been the underlying question for this present study. Comprehensive literature survey was conducted from the electronic databases including ScienceDirect, Wiley, Sage, Scopus, Taylor & Francis, and Google Scholar. The publications in form of reports, conference papers, working papers, discussion papers, journal articles, book sections and textbooks were considered in this study. In total, 11 energy systems including human and animal energy, solid biomass (firewood), hydropower, wind, geothermal, solar, nuclear, peat, coal, petroleum, and non-solid biomass (methanol, hydrogen, ethanol, biodiesel, and biogas) are described. The current and the future development and utilization of these energy systems has been described. The challenges with their development and utilization were elaborated and the solution the challenges were presented. The hydropower with River Nile being the main river for large hydropower plant construction is the dominance energy system in Uganda. Nuclear energy will be the salvation for the country’s electric energy supply in the near future. Therefore, Uganda needs to bet big on nuclear energy.

Developed within the scope of a collaborative R&DT project, a 1 kW pilot unit aimed to perform the recovery of previously liquefied biomass from lignocellulosic forest resi-dues, later used as a carbon source in a co-electrolysis process, intended for the pro-duction of synthesis gas (H2, CO, CO2), also known as syngas. The syngas will be trans-formed into other value-added products, namely synthetic biofuels such as methane, methanol or biodiesel. This paper presents the results of the research currently being carried out at ISEL with the objective of further advancing development on the pilot unit by the execution of optimization tests with and without the addition of two dif-ferent biomass types.

Azolla is a substitute compost that has the potential to enhance nutrient cycling in agricultural systems for sustainable development. In this study, four experiments were conducted to compare the Department of Agriculture (DOA, Thailand)'s methodology for determining the suitable type and rate of animal manure and the optimal light intensity for the growth and yield of Azolla (Azolla microphylla). The results revealed that applying 100% pig manure gave the highest yield of Azolla compared to the other manure. However, there was no discernible difference in yield across the various doses (20.16, 30.16, and 40.16 gN m-2) of pig manure treatments, for which the minimal pig manure dosage of 20.16 gN m-2 was chosen. For further experimentation in the optimal light in-tensity, the 40% shading gave the highest yield of Azolla compared to no shading or 20 and 60% shading. When compared with the DOA Thailand methodology (1.27 kg m-2 of cow manure and covered with a size 32 mesh net), the findings indicated that the modified method (20.16 gN m-2 of pig manure + 40% shading) gave a 16% greater Azolla yield than that under the DOA Thailand methodology.

Biomass fuel pellets exhibit variations in quality due to differences in feedstock sources. Moni-toring processing parameters is crucial for converting biomass into high-quality energetic pellets. This study examined the effects of selected parameters on the properties of cocoa pod husk pellets produced using a modified pelleting machine. The pellets were produced by varying the com-pression ratio (0.8, 1.0, 1.2), moisture content (10, 15, 20%) and binder quantity (0, 2.5, 5 wt%). A Box-Behnken design was employed to structure the experiment. The pellets were analyzed for density, proximate composition (moisture, volatile matter, fixed carbon, and ash contents), and higher heating value to assess their quality. The results were subjected to ANOVA at a 95% con-fidence level. The cocoa pod husk pellets had a bulk density of 0.28-0.41 g/cm³, moisture content of 13.22-19.30% (db), volatile matter of 48.61-57.83%, fixed carbon of 21.25-23.10%, ash content of 3.49-12.99%, and higher heating values of 18.28-19.30 MJ/kg. Significant differences were observed at the 95% confidence level (p≤0.05). Compression ratio, binder quantity and moisture content were found to affect the physicochemical properties of the pellets.

The emergence of "green" materials has been attracting significant attention along the last few years for various applications. Here, we report a rapid, efficient and reproducible microwave-assisted synthesis of graphene quantum dots GQDs of identical features whatever the nature of biomass wastes investigated. The synthesized GQDs were fully characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy and dynamic light scattering. The nanoparticles display narrow size of some nanometers with crystal lattices. Furthermore, the water-soluble particles show excitation-dependent photoluminescence ranging from blue to orange emission wavelength in solution. Interestingly, thin films display white light emission under 325 nm UV-light excitation, while aggregation-induced quenching is usually observed.

Despite the need for a sustainable energy resource, bioenergy gained its spotlight in the 2000s. Sugarcane is a significant crop in terms of sugar and energy capacity, and it can be an alternative energy source to mitigate the effects of climate change. Bioenergy production from sugarcane in Brazil is one of the most efficient. This production lends a centrality to biofuels' importance in confronting the effects of climate change. The present article reviews the Brazilian history of this crop as a biofuel source. We highlight the historical changes related to scientific, technological, industrial, and environmental advances since the beginning of the 20th century. We describe how creating governmental institutes and disseminating scientific knowledge strengthened public policies that led Brazil to occupy leadership positions in producing, distributing, and using bioenergy throughout the country. The compiled data shows the improvement and the new approaches needed in ethanol sugarcane. We developed a bibliometric analysis to evaluate Brazilian science's contribution to this process compared to other countries. Brazil's history of science and investments in sugarcane biofuel development for transportation may be divided into two phases: ethanol-only and flex-fuel cars. A third phase is starting, which is the ethanol-to-hydrogen era.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

Microplastics pollution in sugarcane areas of China is severe, and reducing their ecological risks is critical. This study aims to explore the effects and mechanisms of microplastics combined with or without biochar on sugarcane growth, soil biochemical properties in red soil by a potted experiment. The results showed that compared with control (CK), microplastic alone treatments reduced the dry biomass of sugarcane, soil pH and the nitrogen (N) and phosphorus (P) contents, obviously decreased the observed_OTUs, Chao1 and Shannon indices of soil total bacteria (16S rRNA gene-based bacteria) while increasing them in phoD-harbouring bacteria. Interestingly, microplastics combined with biochar could alleviate the negative effects of microplastic accumulation on sugarcane growth and soil quality. There were significant differences in the bacterial community compositions among different treatments. Compared with CK, all other treatments significantly decreased the relative abundance of Gemmatimonadota while only microplastic combined with biochar treatments significantly increased the abundance of Subgroup_10 for the 16S rRNA gene, and only microplastic alone treatments significantly increased the relative abundance of Streptomyces for the phoD gene. Moreover, the treatments with microplastics combined with biochar increased the relative abundance of Subgroup_10 and Bradyrhizobium while decreased the IMCC26256 and Streptomyces compared with that in the treatment with microplastics alone. Correlation analysis showed that Subgroup_10 and Bradyrhizobium were significantly positively correlated with sugarcane biomass and several soil properties, while IMCC26256 and Streptomyces were just the opposite. Additionally, different treatments also changed the abundance of potential microbial functional genes. Compared to CK, other treatments increased the abundance of aerobic_ammonia_oxidation, denitrification while decreased the abundance of nitrate_respiration, nitrogen_respiration; meanwhile, these four functional genes involved in N cycling processes were obviously higher in treatments with microplastics combined with biochar than in treatments with microplastic alone. In conclusion, microplastics combined with biochar could alleviate the negative effects of microplastic accumulation on sugarcane growth by improve soil nutrients and microbial community structure and function.

With the swift advancement of wearable electronic devices and the electronic textile industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties even after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel materials, processing techniques, and designs for flexible energy storage devices. Among the myriad of materials investigated thus far, biomass-derived architectures have garnered significant attention due to renewability, cost-effectiveness, and abundance in earthly resources. Notably, flexible carbon membrane/ monolithic derived from biomass serve as a particularly promising option for self-supporting electrodes, align seamlessly with the requirements of next-generation electronic devices, and obviate the need for additional costs, unnecessary weight, and the high contact resistance that additive insulating adhesives may entail. This review delves into the comprehensive analysis of biomass feedstocks and methodologies employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of biomass self-supported carbon architectures and the challenges they face is provided.

Recently, the move from cost-tied to open-access data has led to the mushrooming of research in pursuit of algorithms for estimating aboveground grass biomass (AGGB). Nevertheless, a comprehensive synthesis or direction on the milestones archived or an overview of how these models perform is lacking. This study synthesises the research work from decades of experiments in order to point researchers in the direction of what was done, the challenges faced, as well as how the models perform. A pool of findings from 108 remote sensing-based AGGB studies published from 1972 to 2020 show that about 62% of the remote sensing-based algorithms were tested in the Steppe grasslands, mostly in the temperate climate zone. An uneven annual publication yield was observed with approximately 36% of the research output from Asia whereas countries in the global south yielded few publications (<10%). Optical sensors, particularly MODIS, remain a major source of satellite data for AGGB studies, whilst studies in the global south rarely use active sensors such as Sentinel-1. Optical data tend to produce poor regression accuracies that are highly inconsistent across the studies compared to Radar. Vegetation indices, particularly the Normalised Difference Vegetation Index (NDVI), remain a major predictor variable. Predictor variables such as Sward height, Red edge position and Backscatter coefficients produced slightly consistent accuracies. Deciding on the optimal algorithm for estimating AGGB is daunting due to the lack of overlap in the grassland type, location, sensor types, and predictor variables, signalling the need for further studies around the transferability of remote sensing-based AGGB models.

Carotenoids are essential pigments that play a vital role in the photosynthetic process of algae and are important for human health and nutrition. Despite their potential value, algal carotenoids are being neglected by biofuel industries. Recent research is aimed at producing microalgal lipids and carotenoids simultaneously under abiotic stresses. In this study, the effect of different abiotic stress factors such as Nitrogen (N), Potassium (K), Phosphorous (P), Sulphur (S), light intensity, and photoperiod on biomass, lipid, and carotenoids synthesis in Monoraphidium sp. (MP) were explored utilizing a statistical method. In addition, 2, 7-dichlorofluorescein diacetate (DCF-DA) mediated spectrofluorimetry was employed to detect the ele-vation in ROS level. The results revealed that variations in nutrients and light con-ditions are the key factors in the up-regulation of biomolecules lipids and carote-noids in the algae. The carotenoids profiling was done by Ultra Performance Liquid Chromatography Quadrupole Time-of-Flight Mass Spectroscopy (UPLC-Q-ToF-MS). Among consisting carotenoids violaxanthin, astaxanthin, and beta-carotene were enhanced by 1.3 folds, 1.19 folds, 1.08 folds, while lutein was declined by 1.32 folds under stressed condition compared to control. The identified carotenoids are rec-ognized for their importance in the pharmaceutical and nutraceutical industries, highlighting the significant role of MP in these sectors.

The demand for an efficient utilization of abundant biomasses is growing for the production of biogas and valuable bioproducts. Lignocellulose biomass is a cheap and most abundant carbon source for the production of biofuels such as bioethanol, biobutanediol, and other bio-based chemicals. Due to its complex heterogeneity, its hydrolysis gives rise to a mixture of sugars, mainly glucose; a hexose and xylose; a pentose. Glucose is the most abundant carbohydrate monomer. Most microorganisms have evolved the ability to utilize it preferably due to carbon catabolite repression regulatory mechanism at the detriment of the pentoses. Some microbes even lack the ability to utilize them. This has led to the sequential use of these sugars and accompanying reduced productivity due to inadequate utilization of the pentoses. Also, this sequential utilization of the sugars takes time and makes the overall processes economically costly. Since lignocellulose hydrolysates comprise both hexoses and pentoses, the catabolism of these sugar mixtures to biofuels will require an efficient microbial strain capable of simultaneous utilization. The use of CCR negative mutants can achieve this. CCR negative mutants simultaneously utilize pentoses and hexoses, ensuring an improved fermentation efficacy and greater productivity, thus, making the overall bioprocess economically feasible. This article reviewed several approaches employed in creating these mutant microorganisms. A brief insight on carbon catabolite repression and phosphostransferase system were made. It also highlighted the biogas production processes, factors affecting anaerobic digestion, lignocellulosic biomass structure, challenges with their use and solutions to overcoming the challenges.

Seasonal variations in atmospheric ultrafine particulate matter (PM0.1) were monitored in Bangkok, Thailand, from 2016 to 2017. PM0.1 bound organic carbon (OC), and elemental carbon (EC) were collected by a cascade air sampler that can collect PM0.1 and estimated by a thermal-optical carbon analyzer following the IMPROVE-TOR protocol. The annual average PM0.1 in Bangkok was 14.5 ± 4.7 µg/m3, higher than in large Asian cities like Shanghai and Hanoi. Biomass burning from neighboring areas was shown to increase the particle concentration. Apparent risings in carbon species as OC, EC, and OC/EC ratios in the wet and dry seasons were observed, and Char-EC/Soot-EC displayed that the PM0.1 in the Bangkok atmosphere was influenced mainly by the vehicle exhaust, even though the influence of biomass burning was more sensitive during the dry season. The effective carbon ratio (ECR) displays that carbonaceous aerosol is light-absorbing; the dry season increase contributed to climate and air quality. The finding of this work is of great importance to air pollutants control policies in urban areas.

The gasification of sugarcane cutting residues (RAC) is a process that occurs in a gasifier where the transformation of this raw material into a solid-state and a gasifying agent with a moderate calorific value occurs, thanks to the application of heat. And under restricted oxygen levels, we can say that there are several styles of gasifiers for air, steam, oxygen, and hydrogen, all of which have a performance that can be analyzed and categorized by their performance to avoid damage to the environment. (1) The objective of this article is based on the mathematical development using simulation of the gasification of cane cutting residues. (2) In the methodology, the simulation of the gasification and CO₂ capture process was developed from the biomass residues of the sugarcane cutting residues; it was carried out as a transformation of the primary fuel into a gas stream whose main components are CO₂ and H₂, which can be separated relatively easily by their concentrations, available pressures and in some cases, their temperatures; (3) According to the kinetic data obtained, the second-order reaction in the transformation and improvement of the process was identified; applying to the optimization of development in the capture of CO₂, contributing to the reduction of greenhouse gases. (4) The gasification simulation process results in a biomass conversion corresponding to 93% of its feed and the formation of volatiles whose molar fraction corresponds to 37% H₂, 12% CH₄, 37% CO and 12 % CO₂.

Cytochrome P450 (CYPs) is a functionally diversified third-largest gene family that exploded in the plant kingdom. Their role in different organ development has been illustrated by the intervention of phytohormone. Cotton is a model organism for cell differentiation and cell elongation. To decipher the participation of CYPs in different cotton fiber developmental stages, we identified and characterized 2460 CYPs in three diploids and two allotetraploid cottons. Furthermore, In-silico expression and cluster analysis of cotton CYPs was conducted to distinguish the fiber stage-specific clusters that have the determining role in different stages of fiber development. The subgenome expression of two conserved Gossypium hirsutum CYPs, namely, GhCYP78A197 and GhCYP78A198 contributed to fiber initiation at an early stage of fiber development, governed by the co-occurrence of TATA and MYB TFs binding sites. Coexpression network partners of these two GhCYP78A annotated as auxin, kinases, chromatin remodeler, epigenetic regulator and cyclin-related genes that possibly induce the endoreduplication and cell proliferation for fiber cell initiation to define the high yield and biomass.

Pollination is the process by which pollen grains are exchanged in plant flowers to allow for fertilisation and production to take place. However, challenges occur when crops are grown under protected structures where there are minimal activities of natural pollination agents such as wind and animals which are responsible for transferring pollen grains from the anther to the stigma. Therefore, the study objective was to determine the effect on hand pollination on the yield of African horned cucumber grown under greenhouse and shade net environment. A factorial experiment with two factors (hand pollinated and non-hand pollinated/control) was conducted under two different growing environments (greenhouse and shade net). African horned cucumber plants were hand self-pollinated in the morning. Pollen were manually transferred with a hand using the new earbud from the male to the female flowers on the same plant (selfing). Results showed that hand pollinated African horned cucumber plants increased total biomass from 0.93 to 2.23 kg under greenhouse environment. Hand pollinated plants increased harvest index from 0.07 to 0.35 under shade net environment. It can thus, be deduced that hand pollination increases African horned cucumber yield in the greenhouse and shade net environments.

The Italian Stone Pine (Pinus pinea L.) is one of the most employed ornamental trees in towns with Mediterranean climates. For example, in the city of Rome, Pinus is the most common genus, with more than 51,000 trees. This study investigates technical and economic features of maintenance operations of Stone Pines and evaluates the productivity and costs of the observed yards. Pruning and felling are the most frequent management operations of trees in towns and this study analyzes the features of these operations carried out in 14 work sites. The operations were carried out either with aerial platforms (19 trees) or ascending the crown by tree-climbing (6 trees). The operations were sampled with time studies (12 trees for pruning and 13 for felling). Work time was measured from the beginning of operations to the transport of the residual biomass to the collection and loading point, using centesimal stopwatches and video recording. The total residual biomass was weighed or assessed. Total observation time amounted to 63.1 hours. The evaluation of the costs of each work site considered the fixed and the variable costs and the costs for the labor force. A Multiple Linear Regression model (statistics: determination coefficient R2: 0.74, adjusted R2: 0.67, p-value < 0.001) which utilizes four regressors easily evaluable before the work, was adopted to predict the gross time of the operations. This paper can contribute to optimize trees maintenance methods in urban sites and to assess the potential residual wood biomass attainable from urban forestry maintenance in the city of Rome.

Agricultural intensification is considered essential for meeting growing demand for food and biomass for energy and material purposes. Intensifying grasslands is a so-far under-represented although promising option, given their large land area and relatively low management levels. This study quantifies the bioenergy potential from intensifying temporary grasslands in Europe and the integral greenhouse gas emission effects in 2030. We first conduct a literature review of intensification options for European grasslands and then apply the environmental impact assessment model MITERRA-Europe to implement the key intensification option of using multi-species grass mixtures. The results show that 853 kha (or 8%) of temporary grassland could be made sustainably available for additional biomass production. This can be translated into a bioethanol potential of 23 PJ/yr and an emission mitigation potential of 5.8 Mt CO2-eq/yr (if conventional grass mixture from surplus temporary grassland is used for energy) or 72 PJ/yr and 4.0 Mt CO2-eq/yr (if surplus temporary grassland is used for grassy energy crops). Although the bioenergy potential is limited, the intensification measure’s key advantage is that it results in a better environmental performance of temporary grasslands. This makes it a key option for sustainably producing bioenergy in areas with high shares of temporary grasslands.

The combination of eco-respectful epoxy compounds with the humins, a by-product of biomass chemical conversion technologies, allow the obtention of materials with high added value. In this work, we propose the chemical connection study of humins with two aliphatic diepoxides through the copolymerization reactions to synthesize sustainable bio-based thermosets. The mechanism insights for the crosslinking between the epoxides and humins was proposed considering the different functionalities of the humins structure. FT-IR spectroscopy, 1 D and 2 D NMR spectroscopy techniques were used to build the proposed mechanism. By these techniques, the principal chain connections and the reactivity of all the components were highlighted in the synthesized networks.

The processing of fossil fuels is the major environmental issue today which should be lessen. Biomass is gaining much interest these days as an alternate to energy generation. Lignocellulosic biomass (cellulose, hemicellulose and lignin) is abundant and has been used for a variety of purposes. Among them, the lignin polymer having phenyl-propanoid subunits linked together through C-C bonds or ether linkages, can produce numerous chemicals. It can be depolymerized by microbial activity together with certain enzymes (laccases and peroxidases). Both acetic acid and formic acid production by certain fungi contribute significantly to lignin depolymerization. Natural organic acids production by fungi has many key roles in nature that are strictly dependent upon organic acid producing fungus type. Fungal enzymatic conversion of lignocellulosic is beneficial over other physiochemical processes. Laccases, the copper containing proteins oxidize a broad spectrum of inorganic as well as organic compounds but most specifically phenolic compounds by radical catalyzed mechanism. Similarly, lignin peroxidases (LiP), the heme containing proteins perform a vital part in oxidizing a wide variety of aromatic compounds with H₂O_2. Lignin depolymerization yields value-added compounds, the important ones are BTX (Benzene, Xylene and Toluene) and phenols as well as certain polymers like polyurethane and carbon fibers. Thus, this review will provide a concept that biological modifications of lignin using acidophilic microbes can generate certain value added and environment friendly chemicals.

The characteristics of biogenic aerosols in urban area were explored by determining the composition, temporal distribution of saccharides in PM_2.5 in Shanghai. The total saccharides showed a wide range of 15.2 ng/m³ to 1752.8 ng/m³, with the averaged concentrations were 169.8 ng/m³，300.5 ng/m³，288.4 ng/m³，688 ng/m³ in spring, summer, autumn, and winter, respectively. The concerned saccharides include anhydrosaccharides (levoglucosan and mannosan), which were higher in cold seasons due to the increased biomass burning, saccharide alcohols (mannitol, arabitol, sorbitol) and monosaccharides (fructose, glucose), which showed more abundant in warm seasons attributed to the biological emissions. By PMF analysis, four emission sources of saccharides were demonstrated, including biomass burning, fungal spores, soil suspension and plant pollens. Resolution of backward trajectory and fire points showed a process of high concentrations of levoglucosan. We found that concentrations of anhydrosaccharides showed relatively stable under different pollution levels while saccharide alcohols exhibited an obvious decrease, indicated that biomass burning was not the core reason of the heavy haze pollution, however, and high level PM_2.5 pollution might inhibit effects of biological activities.

In order to produce bioethanol from yellow poplar sawdust without detoxification, deacetylation (mild alkali treatment) was performed with aqueous ammonia solution. To select the optimal conditions, deacetylation process was carried out using different conditions: NH₄OH loading (2–10% (w/v)) and solid-to-liquid ratio (1:4–10) at 121 °C for 60 min. In order to assess the effectiveness of deacetylation, fractionation of deacetylated yellow poplar sawdust was performed using dilute acid (H₂SO₄, 0.5–2.0% (w/v)), reaction temperature (130–150 °C) and time (10–80 min). The toxicity-reduced hemicellulosic hydrolysates that were obtained through a two-step treatment at optimized conditions were fermented using Pichia stipitis for ethanol production, without any further detoxification. The maximum ethanol production was 4.84 g/L, corresponding to a theoretical ethanol yield of 82.52%, which is comparable to those of intentionally made hydrolyzates as controls.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Products made from petroleum-derived plastic materials are linked to many environmental problems such as greenhouse gas emissions and plastic pollution. It is desirable to manufacture products from environmentally friendly materials instead of petroleum-based plastic materials. Products made from biomass-fungi composite materials are biodegradable and can be utilized for packaging, construction, and furniture. In biomass-fungi composite materials, biomass particles (derived from agricultural wastes) serve as the substrate and the fungal hyphae network binds the biomass particles together. There are many reported studies on 3D printing of biomass-fungi composite materials. However, there are no reported studies on biodegradation of 3D printed samples from biomass-fungi composite materials. In this study, two types of biomass materials were used to prepare printable mixture hemp hurd and beechwood sawdust. The fungi strain used was Trametes versicolor. Extrusion based 3D printing was used to print samples. 3D printed samples were left for five days to allow fungi to grow. The samples were then dried in an oven for 4 hours at 120ºC to kill all the fungi in the samples. The samples were buried in the soil using a mesh bag and kept in an environmental chamber at 25℃ with a relative humidity of 48%. The weight of these samples was measured every week over the period of three months. Both types of samples (prepared from beechwood sawdust and hemp hurd, respectively) showed weight change after three months. Furthermore, the samples made from hemp hurd had more weight change than the samples made from beechwood sawdust. The SEM (scanning electron microscope) micrographs and FTIR (Fourier transform infrared) spectroscopy showed evidence of biodegradation of these samples.

A one-pot, one-step protocol combining hydrogen transfer initiated dehydration (HTID) of 1,3-propanediol (1,3-PDO), catalysed by [Cp*IrCl2(NHC)] (Cp* = pentamethylcyclopentadienyl; NHC = carbene ligand) complexes (1-5H and 1-3F), and self-aldol condensation (SAC) of propanal (2), allowed selective production of aldehyde 2-methyl-pent-2-enal (3), in ionic liquids with high substrate conversion. The Ir(III) pre-catalysts, and the ionic liquids, were recyclable. 3 could also be selectively produced in the presence of water, and in neat 1,3-PDO. The efficient, selective delivery of a value-added chemical from 1,3-PDO, a major product of many whole cell bacterial fermentation processes, shows that the combination of chemo-catalytic processing of the chemical platform via Cp*IrCl2(NHC) - catalysed HTID / SAC with bio-catalysis has the potential to allow direct valorisation of the bio-renewable feedstocks, such as waste glycerol and sugars, into valuable chemicals.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels, salinity 75 produced consistently favorable results in cell count (13.08 x 10³ ± 1.41 x 10³ cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 97.5 ± 0.1 µg/L, chlorophyll b = 123.6 ± 0.3 µg/L), and desalination (9.32 ± 0.47 reduction). Therefore, salinity 75 was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 10³ ± 535.22 cells/mL), with dry biomass weight being statistically different (higher) than the expected (4.21 ± 0.02 g/L) (p<0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 95.4 ± 2.2 µg/L, chlorophyll b = 128.1 ± 5.1 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Nevertheless, the trial highlights D. salina's strong adaptation to various salinity levels. This suggests a promising future in halophyte research, particularly in understanding the mechanisms that prevent salt accumulation in cells and how to overcome this barrier. Additionally, these results suggest that microalgae could be a viable resource in saline-rich environments unsuitable for conventional agriculture, promoting industrial adaptation to adverse conditions.

Ghana Tamale's current waste management system is overwhelmed by the growing waste crisis, necessitating the exploration of Waste-to-Energy technologies as an innovative solution. This study explores challenges and opportunities for integrating Waste-to-Energy (WtE) technologies into Tamale's existing waste management system. Qualitative research identified policy hurdles, financial constraints, social concerns, and institutional weaknesses as key barriers. Conversely, stakeholder collaboration, public education, and capacity building emerged as some success fac-tors. A proposed implementation plan emphasizes feasibility studies, public engagement, pub-lic-private partnerships (PPPs), and technology selection based on waste composition. Addition-ally, a novel framework for WtE integration within a broader Integrated Solid Waste Manage-ment (ISWM) system is presented. This framework incorporates waste sorting, recycling, WtE alternatives, and responsible management of residuals. Validation by key stakeholders con-firmed the framework's potential to improve waste management in Tamale. By overcoming identified challenges and implementing the proposed framework, Tamale can achieve environ-mental sustainability, energy generation, and progress towards UN SDGs 7, 11, and 12. This re-search offers valuable insights for policymakers and paves the way for a cleaner and more sus-tainable future for Tamale, potentially serving as a model for other developing cities.

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..