Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

One of the most common subgroups of cutaneous T-cell lymphomas is the that of primary cutaneous CD30 positive lymphoproliferative disorders. The group includes lymphomatoid papulosis (LyP) and primary cutaneous anaplastic large cell lymphoma (pcALCL), as well as some borderline cases. Recently, significant progress has been made in understanding the genetics and treatment of these disorders. This review article summarizes the clinical evidence supporting the current treatment options in these diseases. Recent years have seen the introduction of novel agents into clinical practice; most of these target CD30, such as anti-CD30 monoclonal antibodies and conjugated antibodies (brentuximab vedotin), bispecific antibodies and cellular therapies, particularly anti-CD30 CAR-T cells. This paper briefly reviews the biology of CD30 that makes it a good therapeutic target, and describes the anti-CD30 therapies that have emerged to date.

Objectives: Chylothorax is a relatively rare condition of lymphatic fluid accumulation in the thoracic cavity due to a leakage from the thoracic duct or its tributaries. Patients present with dyspnea, malnutrition, and immunosuppression. Treatment can be conservative or surgical, depending on etiology and clinical course. The optimal management algorithm for chylothorax is still controversial. Methods: This is a retrospective study of all patients with chylothorax treated at our Department of Thoracic Surgery during the 10-year period. Results: A total of 14 patients were identified for the study. Nine patients had chylothorax after lung or esophageal cancer surgery. Four patients had chylothorax in advanced lymphoma. One patient had chylothorax after blunt chest trauma. A conservative approach was initiated in most patients (92%), including pleural drainage, nil per mouth, total parenteral nutrition, and somatostatin 0.1 mg bid subcutaneously. Surgical treatment was indicated in patients with thoracic drain production >800 mL per day beyond the fifth day of treatment and those with blunt thoracic trauma. Two patients had thoracic duct ligation via right-sided thoracotomy, and five patients had video-assisted thoracoscopic thoracic duct ligation with the immediate arrest of chylous leakage. Conclusion: Chylothorax should be treated conservatively initially. Surgical treatment should not be delayed in case of failure beyond the fifth day. In our series of patients, a video-assisted thoracoscopic approach for thoracic duct ligation proved to be minimally invasive, highly efficient, and well tolerated by patients and, therefore, should be the preferable route of surgical treatment.

Estimating age at death is essential to establish a biological profile from human skeletal remains in both forensic and archeological settings. Imaging studies of skeletal age changes in adults have described metamorphosis of trabecular bone structure and bone loss in the proximal femur , as well as changes in morphology during different stages of life. This study aims to assess the utility of a digital representation of conventional X-ray films of the proximal femur for the estimation of age at death in a sample of 91 adult individuals (47 females and 44 males) of the Coimbra Identified Skeletal Collection. The proposed approach showed a root mean squared error (RMSE) of 17.32 years (and mean absolute error of 13.47 years) for females and an RMSE of 14.06 years (mean absolute error of 11.08 years) for males. The main advantage of this approach is the consistency in the feature detection and extraction, as X-ray images projected on the femora space will always produce the same set features to be analyzed for age estimation while more traditional methods rely heavily on operator experience which can lead to inconsistent age estimates among experts.

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

This paper uses probability method to evaluate the fire safety performance of prestressed steel-concrete beam bridges based on simulation experimental research. Firstly, fire simulation experimental sample analysis was conducted on actual small box girder bridges to obtain the structural response of prestressed steel-concrete structures under fire, which is in line with engineering practice. Next, construct a reliability analysis model for the fire resistance performance of prestressed steel-concrete beam bridges; Combining reliability theory with finite element method, establish a reliability analysis method for the fire resistance performance of prestressed steel-concrete beam bridges. Subsequently, a safety factor evaluation model for the fire resistance performance of prestressed steel-concrete beam bridges was proposed, and a safety factor evaluation method for the fire resistance performance of prestressed steel-concrete beam bridges based on reliability back analysis was established. Finally, based on the analysis of the structural response after a fire in a specific case of a simply supported to continuous prestressed steel-concrete continuous beam bridge project, a structural resistance sample of the prestressed steel-concrete beam bridge is generated through uniform design method, and statistical analysis is conducted. Subsequently, probability methods are used to evaluate the safety of the prestressed steel-concrete beam bridge after a fire. Through analysis, it can be concluded that the time of fire has a significant impact on the structural performance of prestressed steel-concrete beam bridges, and the randomness of parameters has a significant impact on the safety reserve of prestressed steel-concrete beam bridges after fire. It is necessary to pay attention to it in specific engineering practice and strengthen the monitoring and statistics of structural random characteristics.

Frontotemporal dementia (FTD) is the second most common form of presenile dementia; however, its diagnosis has been poorly investigated. Previous attempts to diagnose FTD using quantitative electroencephalography (qEEG) have yielded inconsistent results in both spectral and functional connectivity analyses. This study aimed to introduce an accurate qEEG marker that could be used to diagnose FTD and other neurological abnormalities. We used open-access electroencephalography data from OpenNeuro to investigate the power ratio between the frontal and temporal lobes in the resting state of 23 patients with FTD and 29 healthy controls. Spectral data were extracted using a Fast Fourier Transform in the delta (1–4 Hz), theta (4–8 Hz), alpha (8–13 Hz), beta (13–32 Hz), and gamma (32–45 Hz) bands. We found that the spectral power ratio between the frontal and temporal lobes is a promising qEEG marker of FTD. Frontal/temporal (F/T) theta/alpha, alpha/theta, al-pha/gamma, and gamma/alpha showed a consistently high discrimination score for the diagnosis of FTD for different parameters and referencing methods. The study findings can serve as reference for future research focused on diagnosing FTD and other neurological anomalies.

Diverse candidate antibodies are needed to successfully identify therapeutic and diagnostic applications. The variable domain of IgNAR (VNAR), a shark single-domain antibody, has attracted attention owing to its favorable physicochemical properties. The phage display method used to screen for optimal VNARs loses sequence diversity because of the bias caused by the differential ease of protein expression in Escherichia coli. Here, we investigated a VNAR selection method that combined panning with various selection pressures and next-generation sequencing (NGS) analyses to obtain additional candidates. We constructed a VNAR phage library from the spleen of the Japanese topeshark (Hemitriakis japanica). Drawing inspiration from the physiological conditions of sharks and physicochemical properties of VNARs, we examined the effects of NaCl and urea concentrations, low temperature, and preheating at the binding step of panning. NGS analysis was performed to select the specifically enriched clones under each panning condition. The identified VNARs exhibited higher reactivity than those obtained by panning without selection pressure. Additionally, they possess physicochemical properties that reflect their respective selection pressures. These results can greatly enhance our understanding of VNAR properties and offer guidance for the screening of high-quality VNAR clones that are present at low frequencies.

Rationale: Chronic Granulomatous Disease (CGD) is a rare primary immunodeficiency. Although most mutations are linked to the X chromosome, therefore affecting males, there are autosomal recessive forms that therefore affect both sexes. Clinically it is characterized by recurrent and severe bacterial and fungal infections, with formation of granulomas, due to the inability of phagocytes to generate reactive oxygen compounds, necessary for the intracellular death of phagocytosed microorganisms. Patient concerns: We reported a 12-year-old boy with pneumonia with pneumatocele of possible staphylococcal etiology at one year of age, bilateral orchitis secondary to Salmonella with hematogenous spread, osteomyelitis due to Salmonella, gastroenteritis due to Salmonella enteritidis, liver abscesses due to Staphycococcus aureus and lymphomatoid papulosis and pyodermititis. Diagnoses: In the biochemical diagnosis, the presence of yellow dye (NBT) and absence of dark bluish black dye (formazan) was evidenced. Regarding the genetic diagnosis, the presence of the mutation in exon 10 of CYBB (OMIM 306400) (Xp21.1) that encodes the gp91phox protein was demonstrated. Interventions and outcomes: Treatment was started with trimethoprim/sulfamethoxazole 400/80 mg every 24 hours via oral, and antifungal prophylaxis with itraconazole 200 mg every 24 hours orally is added, after which he does not present serious bacterial or fungal infections, not being able to administer immunomodulatory treatment with recombinant human Interferon gamma-1b. Lessons: The clinical finding of frequent severe infections associated with granulomas, CGD should be suspected. Treatment of this primary immunodeficiency is trimethoprim/sulfamethoxazole and itraconazole. Importantly, it indicated that the mutation in exon 10 of CYBB (Xp21.1) that encodes the gp91phox might influence the pathogenesis of CGD.

The technical capabilities of modern Industry 4.0 and Industry 5.0 are rather vast and growing exponentially daily. The present-day Industrial Internet of Things (IIoT) combines manifold underlying technologies that require real-time interconnections and communications among heterogeneous devices. Smart cities are established with sophisticated designs and control for seamless Machine-to-Machine (M2M) communication to optimize resources, costs, performances, and energy distribution. All the sensory devices within a building interact to maintain a sustainable climate for residents and intuitively optimize the energy distribution to optimize energy production. However, it encompasses quite a few challenges for devices that lack compatible and interoperable designs. Conventional solutions are restricted to limited domains or rely on engineers to design and deploy translators for each pair of ontologies. This is a costly process in terms of engineering efforts and computational resources. The issue persists that a new device with a different ontology must be integrated into an existing IoT network. We propose a self-learning model that can determine the taxonomy of devices given their ontology meta-data and structural information. The model finds matches between two distinct ontologies using the Natural Language Processing (NLP) approach for learning linguistic contexts. Then, by visualizing the ontology network as a knowledge graph, it is possible to learn the structure of the meta-data and understand the device's message formulation. Finally, it can align entities of both ontology graphs similar in context and structure. Furthermore, the model performs dynamic M2M translation without requiring extra engineering or hardware efforts.

Diffuse optical tomography (DOT) technology enables a differentiation between oxyhemoglobin (HbO) and deoxyhemoglobin (HbR) in the sensory and motor cerebral gyri, resulting in greater sensitivity for cerebral activation compared to functional magnetic resonance imaging (fMRI). Here, we introduce a novel approach where functional regions of interest (ROIs) are created based on the specific signal behavior observed in DOT measurements, in contrast to the conventional use of structural-ROIs obtained from anatomical information. The generation of cerebral activation maps involves using the general linear model (GLM) to compare the outcomes obtained from both the functional and structural ROI approaches. DOT-derived maps are then compared with maps derived from fMRI datasets considered the gold standard for assessing functional brain activity. The results obtained demonstrate the effectiveness of employing functional ROIs to improve the spatial location of functional activations in the sensory and motor cerebral gyri by leveraging the neural synchronization data provided by DOT. Furthermore, this methodology simplifies data processing in animal models, where anatomical differences compared to the human head can pose challenges. By incorporating functional ROIs prior to GLM application, this study offers enhancements to DOT analysis techniques and broadens its applicability in both human and animal models.

In the absence of a holistic view of Landscape Sustainability, credible data and consistent information are needed to help decision making and support adaptive management. However, consolidated tools (system of standards and controls) of assessment exist, but show a complexity of the references on one hand, and are mostly qualitative and environmental indicators based on the other hand. This review article deals with the theme of both environmental and landscape indicators in general, the principles and the fundamental definitions. The main models used, the prerequisites and various fields of application are also taken into consideration. Last but not least, various environmental and landscape indicators are presented and compared.

The Colony-Forming Unit (CFU) counting problem remains a complex issue without a universal solution in biomedical and food safety domains. A multitude of sophisticated heuristics and segmentation-driven approaches have been proposed by numerous researchers. Among those, U-Net is the most frequently cited and popular Deep Learning method. The latter approach provides a segmentation output map and requires an additional counting procedure which accounts for unique segmented regions and detected microbial colonies. However, because of pixel-based targets it tends to generate irrelevant artifacts or errant pixels, leading to inaccurate and mixed post-processing results. In response to these challenges, we propose a novel hybrid counting approach, incorporating a multi-loss U-Net reformulation and a post-processing Petri dish localization algorithm. First of all, our unique innovation lies in the multi-loss U-Net reformulation. We introduce an additional loss term at the bottleneck U-Net layer, focusing on delivering an auxiliary signal indicating where to look for distinct CFUs. Second, our novel localization algorithm accurately incorporates an agar plate and its bezel into the CFU counting routines. Finally, our proposition is further enhanced by the integration of a fully automated solution. This comprises a specially designed uniform Petri dish illumination system and a counting web application. The latter application is capable of directly receiving images from the camera, which are subsequently processed, and the segmentation results are sent back to the user. This feature provides an opportunity to correct the CFU counts, offering a feedback loop that contributes to the continued development of the Deep Learning model. Through extensive experimentation, we have found that all probed multi-loss U-Net architectures incorporated in our hybrid approach consistently outperform their single-loss counterparts which utilize exclusively the combination of Tversky and Cross-Entropy training losses at the output U-Net layer. We report further significant improvements by the means of our novel localization algorithm. This reaffirms the effectiveness of our proposed hybrid solution in addressing contemporary challenges of the precise in-vitro CFU counting.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

The abandonment of inland areas has become a major demographical challenge, establishing a condition of local fragility in terms of spatial marginalization. To deal with this issue, a number of policy actions have been released over the time, namely the National Strategy for Inland Areas, established in Italy a decade ago, and more recently the Next Generation EU (NGEU) to foster local economic recovery and employment. In this context, RI.P.R.O.VA.RE., a project funded by the former Italian Ministry of the Environment and Protection of Land and Sea (MATTM), aimed at strengthening the resilience characteristics of communities and territories, focusing on areas falling in the Matese and Ufita in Campania Region and the Medio Agri in Basilicata Region (Southern Italy). Besides the ability to respond to different pressure factors (demographics, economic, geophysical, etc.), the project dealt with seismic, hydraulic and landslide risk conditions in the Matese area, proposing mitigation measures. After presenting the developed methodology, the results obtained for the study area are presented and discussed. The procedure can be applied as supporting tool to enhance the regeneration of inland areas.

Accurate prediction of crop production is essential in effectively managing agricultural countries' food security and economic resilience. This study evaluates the performance of statistical and machine learning-based methods for large-scale crop production forecasting. We predict the quarterly production of 325 crops (including fruits, vegetables, cereals, non-food, and industrial crops) across 83 provinces in the Philippines. Using a comprehensive dataset of 10,949 time series over 13 years, we demonstrate that a global forecasting approach using a state-of-the-art deep learning architecture, the transformer, significantly outperforms traditional local forecasting approaches built on statistical and baseline methods. By leveraging cross-series information, our proposed way is scalable and works well even with time series that are short, sparse, intermittent, or exhibit structural breaks/regime shifts. The results of this study further advance the field of applied forecasting in agricultural production and provide a practical and effective decision-support tool for policymakers that oversee the farm sector on a national scale.

The SARS-CoV-2 virus, causative agent of COVID-19, is known for its genetic diversity. Virus variants of concern (VOCs) as well as variants of interest (VOIs) are classified by the World Health Organization (WHO) according to their potential risk to global health. This study seeks to enhance the identification and classification of such variants by developing a novel bioinformatics criterion centered on the virus's spike protein (SP1), a key player in host cell entry, immune response, and a mutational hotspot. To achieve this, we pioneered a unique phylogenetic algorithm which calculates EIIP-entropy as a distance measure based on the distribution of the Electron-Ion Interaction Potential (EIIP) of amino acids in SP1. This method offers a comprehensive, scalable, and rapid approach to analyze large genomic data sets and predict the impact of specific mutations. This innovative approach provides a robust tool for classifying emergent SARS-CoV-2 variants into potential VOCs or VOIs. It could significantly augment surveillance efforts and understanding of variant characteristics, while also offering potential applicability to the analysis and classification of other emerging viral pathogens and enhancing global readiness against emerging and re-emerging viral pathogens.

Background: Primary lymphedema is a chronic condition caused by a developmental abnormality of the lymphatic system and its malfunction. Different surgical options such as physiologic and excisional procedures have been proposed. The aim of this study was to present a complete algorithm for the treatment of primary lower extremity lymphedema: Primary LYmphedema Multidisciplinary Approach (P-LYMA). Methods: Nineteen patients were treated according to the P-LYMA. Patients underwent pre- and post-operative complex decongestive therapy (CDT). Different physiologic and excisional procedures were performed independently or in combination. The primary outcome was the circumferential reduction rate (CRR). The Lymphedema Quality of Life Score (LeQOLiS), reduction in the number of episodes of cellulitis, length of stay, and complications were recorded. Results: The mean CRR calculated was 72.8±19.6% after twelve months. The episodes of cellulitis per year decreased from a mean of 1.9±0.8 preoperative to 0.4± 0.6 throughtout follow-up. Two patients experienced minor complications. Mean hospitalization time was 5 days. Patients’ quality of life (LeQOLi score) drastically improved from 70.4±11.6 to 24.2 ±13.9 at twelve months post-op. Conclusion: The P-LYMA algorithm allows to maximize surgical results and improve the quality-of life in patients who suffer from primary lymphedema. CDT is mandatory to optimize results.

Despite recent advances in optimizing reliever, controller and maintenance therapy in asthma, a large subgroup of asthmatic patients continues to suffer from severe asthma, affecting their psychosociological status, their quality of life and even their life expectancy. Identifying and recognizing the specific phenotypic and endotypic characteristics in asthma has provided the medical community to drive the development of targeted therapies that are proved to benefit patients in terms of symptom control, exacerbation rate, quality of life and lung function. Adopting a more tailored and targeted approach is proving to be the key factor in reforming severe asthma treatment, minimizing the patients’ burden, as well as the socioeconomical impact worldwide. In this review, we are going to describe the different phenotypes and endotypes of asthma, the currently approved targeted therapies in severe asthma as imprinted in Global Initiative for Asthma (GINA) 2023, as well as other potential pharmacological agents and strategies investigated or currently under investigation for the treatment of severe asthma.

In a limestone quarry mine, fragmentation is a crucial outcome of blasting operations. The optimization of blasting operations greatly benefits from the prediction of rock fragmentation. The main factors that affect fragmentation are rock mass characteristics, blast geometry, and explosive properties. This paper is a step towards the implementation of machine learning and deep learning algorithms for predicting the extent of fragmentation (in percentage) in opencast mining. Various parameters can affect fragmentation. But, in this paper initially, ten parameters (spacing, drill hole diameter, burden, average bench height, powder factor, number of holes, charge per delay, uniaxial compressive strength, specific drilling, and stemming) are collected to train the model. However, due to a weak correlation with rock fragmentation, drill diameter, Average bench height, compressive strength, stemming, and charge per delay are eliminated to reduce model complexity. A total of 219 data sets having five input features i.e., the number of holes, spacing, burden, specific drilling, and powder factor are used to develop the models. To predict rock fragmentation due to blasting in limestone quarry mines, both machine learning models (Random Forest Regression (Bagging), Support Vector Regression, and XG Boost Regression (Boosting)), as well as a deep learning model (Neural Network Regression), are applied to develop a model that can optimize the prediction of fragmentation. The Artificial neural network model optimization showed that the model with architecture 64-32-16-1 can perform well giving MSE (mean squared error) values of 41.32 and 28.59 on training and test data respectively. The R2 value for both training and test is 0.83. Random Forest regression is also performing well compared to SVR and XG boost with the MSE value 12.37 and 9.89 on training and testing data respectively. Here, the R2 value for both sets are 94%. Based on the permutation importance and Shapely plot values, the powder factor has the highest impact, and the burden has the lowest impact on fragmentation.

In real-life scenario, there are many mathematical tools to handle the incomplete and imprecise data. One of them is the fuzzy approach. This article aims to contribute to the literature of fuzzy multi-objective dynamic programming issues involving the fuzzy objective functions. The piecewise quadratic fuzzy numbers characterize these fuzzy parameters. Some basic notions in the problem under the α-pareto optimal solution concept is redefined and analyzed to study the stability of the problem. Furthermore, a technique, named as enhancing decomposition approach, is presented for achieving a subset for the parametric space that contains the sameα-pareto optimal solution. For a better understanding and comprehension of the suggested concept, a numerical example is provided.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

The IDS serves as a security system that maintains constant surveillance over network traffic and host systems in order to identify any security breaches or potentially concerning activities. Recently. the rise in cyber-attacks has driven the necessity for the development of automated and intelligent network intrusion detection systems. These systems are designed to learn the typical patterns of network traffic, allowing them to identify any deviations from normal behaviour, which can be classified as anomalous or malicious. Machine learning methods are widely used to exhibit a satisfactory effectiveness in detecting malicious payloads in the network traffic. While the volume of the data generated from IDS is increasing exponentially results in the emergence of substantial security risks, it highlighted the imperative to strengthen network security. The performance of traditional machine learning methods depends on the dataset and the data balance distribution in it. while most of IDS datasets suffer from unbalancing, this limits the performance of the machine learning method used in the system and results in missed detections and false alarms in the conventional IDSs. To address this issue, this paper presents a new model-based Generative Adversarial Network (GAN) called TDCGAN to enhance the detection rate of less of minor class in the dataset while maintaining efficiency. The proposed model consists of one generator and three discriminators with an election layer at the end of architecture. The UGR’16 data set is used for evaluation purposes. In order to demonstrate the efficacy of our proposed model, various machine learning algorithms have been utilized for comparison. The experimental findings have determined that TDCGAN presents an efficient resolution for addressing imbalanced intrusion detection and surpasses the performance of other oversampling machine learning methods.

We propose an algorithm for generating a panoramic image of a pipe’s inner surface based on inverse perspective mapping (IPM). For efficient crack detection, we used only perspective images of the pipe interior that can be obtained with a single lens camera instead of those taken with a 360-degree camera or a 3D depth camera. Frontal images taken while passing through the pipe were converted to images of the inner surface of the pipe using IPM. We derived a generalized IPM formula that considers the slope of the image plane to correct image distortion caused by the tilt of the plane; this IPM formula was derived based on the vanishing point of the perspective image, which was detected using optical flow techniques. Finally, the multiple transformed images with overlapping areas were combined via image stitching to create a panoramic image of the inner pipe surface. To validate our proposed algorithm, we restored images of pipe inner surface using a 3D pipe model and used these images for crack detection.

Mucosal vaccines offer several advantages over injectable conventional vaccines, such as adaptive immunity induction, secretory IgA production at the entry site of most pathogens, and needleless vaccinations. Despite their potential, only a few mucosal vaccines are currently used. Developing new effective mucosal vaccines strongly relies on identifying innovative anti-gens, efficient adjuvants, and delivery systems. Several approaches based on phages, bacteria, or nanoparticles have been proposed to deliver antigens to mucosal surfaces. Bacterial spores have also been considered antigen vehicles, and various antigens have been successfully exposed on their surface. Due to their peculiar structure, the spores conjugate the advantages of live microorganisms with synthetic nanoparticles. When mucosally administered, spores expressing anti-gens have been shown to induce antigen-specific, protective immune responses. This review accounts for recent progress in the formulation of spore-based mucosal vaccines, describing the spore's structure, specifically the spore surface, and the diverse approaches developed to improve its efficiency as a vehicle for heterologous antigen presentation.

Abstract Natural disasters such as earthquakes have affected urban historical centers severely. Considering the limitations of the existing methods in conservation and preservation of these sensitive areas, and recent advances in technological devices and techniques such as GIS and 3D printers, this article aims to propose a new methodology utilizing available knowledge and resources. The authors of the present research propose an innovative, technological, and highly accurate method to assess the seismic vulnerability of historical contextures rectifying the existing obstacles and limitations. Through this methodology, the level of trial and error is substantially reduced and the output is stronger, more optimized and more conservative as compared with commonly used methods. Using high tech principles and theoretical foundations (i.e. sustainability principles) this method achieves updated analyses, practical plans, and economic optimization.

The purpose of this study was to model the impact of mentoring on women’s work-life balance. Indeed, this study considered mentoring as a solution to create a work-life balance of women. For this purpose, semi-structured interviews with both mentors and mentees of Tehran Municipality were conducted and the collected data were analyzed using constructivist grounded theory. Findings provided a model of how mentoring affects women's work-life balance. According to this model, role management is the key criterion for balancing work-life of women. In this model, antecedents of role management and the contextual factors affecting role management, the constraints of mentoring in the organization, as well as the consequences of effective mentoring in the organization are described. The findings of this research contribute to the mentoring literature as well as to the role management literature and provide recommendations for organizations and for future research.

Monte Carlo Filtering (MCF) is one of the methods of Experimental Statistical Energy Analysis (E-SEA), which allows the correction of a negative LF (Loss Factor). In this article, a modification of the MCF method, called DESA (Diagonal Extension of the Search Area), is proposed. The technique applies a non-uniform extension of the search area when generating a population of normalized energy matrices. The degree of expansion of the search area is controlled by the Diagonal Penalty Factor (DPF). The authors demonstrated the method's effectiveness on a system that could not be identified in several frequency bands by the classical MCF method. After applying DESA, it was possible to fill in the problematic bands that were missing CLF and DLF values. The paper also proposes a way to minimize the errors introduced by using overly high DPF values.

Rural environment has experienced changes as a result of Covid-19, which encourage the introduction of sustainability in education. However, the representation of rurality in school geography and in the 2030 Agenda are factors that continue to present rurality as a concept opposed to urban spaces. The objective was to investigate the perception that the student has about the rural environment from an instrument and his drawings to understand if the explanation of it allows to introduce elements related to sustainability in educational projects. The quantitative research approach allows analyzing the psychometric properties of an instrument to measure the perception of the rural environment of a sample of 300 fifteen-year-old students from Brazil, Colombia and Spain. Those school knowledges that idealize rurality warn of the pedagogical difficulties to promote the teaching of rurality from sustainability criteria and condition the formation of students from a citizenship committed to social problems. This study is important because it diagnoses the elements that intervene in the teaching of rurality from school geography and provides some suggestions to include sustainability in educational projects.

Background: The COVID-19 pandemic has sped up digital health transformation across the health sectors to enable innovative health service delivery. Such transformation relies on competent managers with the capacity to lead and manage. However, the health system has not adopted a holistic approach in addressing the health management workforce development needs, with many hurdles to overcome. The objectives of this paper are to present the findings of a three-step approach in understanding the current hurdles in developing a health management workforce that can enable and maximise the benefits of digital health transformation, and to explore ways of overcoming such hurdles. Methods: A three-step, systematic approach was undertaken, including an Australian digital health policy documentary analysis, an Australian health service management postgraduate program analysis, and a scoping review of international literatures. Results: The main findings will guide the formulation of strategies in developing a digitally enabled health management workforce in the digital health era. Conclusions: With the ever-changing landscape of digital health, being able to lead and manage in times of system transformation requires a holistic approach to develop the necessary health management workforce capabilities and system-wide capacity. The evidence would support that this can be achieved with the required system, policy, educational and professional organizational enablers, which drive a digital health focused approach across all the healthcare sectors, in a coordinated and contextual manner.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

Following the development and dissemination of new climate-smart agricultural technologies to farmers globally, there has been an increase in the number of socio-economic studies on the adoption of climate-smart integrated pests’ management (CS-IPM) technologies over the years. In this study, we review empirical evidence on adoption determinants of CS-IPM technologies and identify possible science-policy interfaces. Generally, our review shows that socioeconomic and institutional factors are influential in shaping CS-IPM adoption decisions of farmers. More specifically, income was found to positively influence the adoption of CS-IPM technologies while land size owned influences CS-IPM adoption negatively. Registered land tenure (registered secure rights) positively influences CS-IPM technologies’ adoption, implying that efficient land markets that enable competitive and fair distribution and access to land, more so by the vulnerable but efficient smallholder producers do indeed increase the adoption of CS-IPMs technologies. Social capital, achieved via farmers’ organizations is also central in fostering CS-IPM technologies’ adoption, just as markets reforms that minimize market failures regarding access to credit, labor, and agricultural information, which could indirectly hinder farmers’ use of CS-IPM practices. Functional extension systems that improve farmers’ awareness of CS-IPM do also improve CS-IPM technologies’ adoption. However, the adoption of CS-IPM technologies in Ghana and Benin is slow-paced because of factors like lack of access to farm inputs that facilitate uptake of these technologies, lack of credit facilities, and limited extension services among others. Interestingly, our review confirms that CS-IPM technologies do indeed reduce and minimize the intensity of pesticide usage and foster ecosystem (environmental and human) health. Therefore, this review unearths strategic determinants of CS-IPM adoption and makes fundamental guidance around climate-smart innovations transfer and environmental policies that should be prioritized to curb environmental pollution and ensure agricultural ecosystems’ sustainability.

The present is a study of the CFD simulations intended to simulate the emissions of pollutants that are generated after the combustion of proposed alternative aircraft fuels (Hydrogen, Ethanol and Methane) to compare with the emissions generated after the combustion of Kerosene and Benzene in a 2D cylindrical combustion chamber. Given that air traffic is a main contributor to not only 3% of man-made greenhouse effects but also of the generation of smog over heavy air traffic urban areas generating an impact on the air quality and the population of those areas.

This work aims to develop an autonomous system for the unmanned aerial vehicle (UAV) to land on a moving platform such as the automobile or marine vessels, providing a promising solution for a long-endurance flight operation, a large mission coverage range, and a convenient recharging ground station. Different from most state-of-the-art UAV landing frameworks which rely on UAV’s onboard computers and sensors, the proposed system fully depends on the computation unit situated on the ground vehicle/marine vessel to serve as a landing guidance system. Such novel configuration can therefore lighten the burden of the UAV and computation power on the ground vehicle/marine vessel could be enhanced. In particular, we exploit a sensor fusion-based algorithm for the guidance system to perform UAV localization, whilst a control method based upon trajectory optimization is integrated. Indoor and outdoor experiments are conducted and the result shows that a precise autonomous landing on a 43 X 43 cm platform could be performed.

Model understanding is critical in many domains, particularly those involved in high-stakes decisions, i.e., medicine, criminal justice, and autonomous driving. Explainable AI (XAI) methods are essential for working with black-box models such as Convolutional Neural Networks. This paper evaluates the traffic sign classifier of Deep Neural Network (DNN) from the Programmable Systems for Intelligence in Automobiles (PRYSTINE) project for explainability. The results of explanations were further used for the CNN PRYSTINE classifier vague kernels` compression. After all, the precision of the classifier was evaluated in different pruning scenarios. The proposed classifier performance methodology was realised by creating the original traffic sign and traffic light classification and explanation code. First, the status of the kernels of the network was evaluated for explainability. For this task, the post-hoc, local, meaningful perturbation-based forward explainable method was integrated into the model to evaluate each kernel status of the network. This method enabled distinguishing high and low-impact kernels in the CNN. Second, the vague kernels of the classifier of the last layer before the fully connected layer were excluded by withdrawing them from the network. Third, the network's precision was evaluated in different kernel compression levels. It is shown that by using the XAI approach for network kernel compression, the pruning of 5% of kernels leads only to a 1% loss in traffic sign and traffic light classification precision. The proposed methodology is crucial where execution time and processing capacity prevail.

During planetary exploration mission operations, one of the key responsibilities of the instrument teams to determine data viability for subsequent analysis. During the 2019 CanMoon Lunar Sample Return Analogue Mission, the Lead Raman Specialist manually examined each spectra to provide quality assurance/validation. This non-trivial process requires years of experience to complete accurately. With the proven efficacy of Convolutional Neural Networks (CNNs) in classification tasks, and the increased use of automation and control loops on planetary space platforms for navigation and science targeting, an opportunity presents itself to approach this validation problem utilising CNNs. We present the Generalised Raman Validation Network (GRaVN), an neural network focused specifically on extracting the generalised structure of Raman spectra for quality assurance/validation. This work demonstrates the viability of utilising a CNN network in validation activities for Raman spectroscopy. Utilising only two hidden layers, a configuration was developed that provided good levels of accuracy on a manually curated dataset. This indicates that such a system could be useful as part of an autonomous control loop during planetary exploration activities.

The stress testing methodology should be implemented and applied to the entity's overall financial system at least annually, and if the organization operates in a volatile economy, it should be performed at least twice a year. Finally, managers should include regular training and development sessions for relevant employees of their organization to be fully informed and more informed and informed, considering the evolving science, theory and practicality of a discrete range of stress testing mechanisms that can be appropriately applied to overall financial framework and system of multiple financial institutions and banks. In addition, stress testing is essentially a methodology that collects and analyzes certain future macro-prudential and micro-prudential economic drivers and indicators, the primary purpose of which is to assess the future financial and economic well-being, level of growth and status quo of a financial institution, bank, organization, credit institution or economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. with the primary intention of assessing the future financial and economic well-being, level of growth and status quo of a group of financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically targeted and incorporated into a paper that substantially and broadly discussed and summarized the importance of the feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. with the primary intention of assessing the future financial and economic well-being, level of growth and status quo of a group of financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. the level of growth and status quo of the financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. the level of growth and status quo of the financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries.

From gene expression studies to identifying microbes quantitative polymerase chain reaction (qPCR) is widely used in research and medical diagnostics. In transmittable diseases like the Ebola outbreak in West Africa (2014-2016), or the present SARS-CoV2 pandemic qPCR plays a key role in the detection of infected patients. Although the technique itself is decades old with reliable approaches (eg. TaqMan essay) in the diagnosis of pathogens many people showed distrust in it during the SARS-CoV2 outbreak. This came mainly from not understanding or misunderstanding the principles of qPCR. This situation motivated us to design a simple laboratory practical class, in which students have opportunities to understand the underlying principles of qPCR and its advantages in microbiological diagnosis. Moreover, during the exercise, students can develop skills such as handling experimental assays, and the ability to solve problems, discuss their observations. Finally, this activity brings them closer to the clinical practice and they can see the impact of the science on real life. The class is addressed to undergraduate students of biological sciences.

Evidence-based healthcare integrates the best research evidence with clinical expertise in order to make decisions based on the best practices available. In this context, the task of collecting all the relevant information, a recall oriented task, in order to take the right decision within a reasonable time frame has become an important issue. In this paper, we investigate the problem of building an effective Consumer Health Search (CHS) systems that use query variations to achieve high recall and fulfill the information needs of health consumers. In particular, we study an intent-aware gain metric used to estimate the amount of missing information and make a prediction about the achievable recall for each query reformulation during a search session. We evaluate and propose alternative formulations of this metric using standard test collections of the CLEF 2018 eHealth Evaluation Lab CHS.

As one of the unique destinations in Iran, Abdanan Black Twin Lake attracts many tourists yearly. Among striking features is the presence of minerals, boiling springs, and its beautiful landscape. Human beings are willing to spend money on such natural resources. An economic valuation can be interfered constructively and positively in improving environmental policies. So, quantifying these benefits is of the utmost importance. The paper mainly estimated the tourists' willingness to pay and their recreational value using the contingent valuation method. Random sampling was conducted on 384 people using the two-dimensional double-choice questionnaire in spring 2019. In the Twin Lake Recreational Value Questionnaire, the main questions were devoted to the visitors' willingness to pay, with three bids of 0.07 $, 0.14 $, and 0.22$. Among 384 respondents, 304 (79%) were willing to pay for recreational use of the lake, and 80 respondents (21%) were not. The likelihood, the model's parameters were estimated. The findings indicated the average tourists' willingness to pay for recreational value was estimated at 0.09$ per visit and the recreational value of this lake for each household was estimated at 0.40$. The findings revealed the effect of education, household income, household size and tourists' willingness to pay was significant.

This paper discusses the use of a participatory approach to assess the level of understanding of the Water-Energy-Climate Change nexus in South Africa. The aim is to facilitate the development of well-coordinated, systematic, and holistic strategies for efficient management of the nexus and its implications in the country. The assessment was guided by the broader Integrated Water Resource Management framework, which promotes a participatory approach in the administration of water resources. The paper argues that despite the reasonable level of understanding of WECC, there is still a lack of integrated policy development and planning among key stakeholders. This is exacerbated by limited coordination and consultation among these stakeholders, particularly policymakers. This necessitates the urgent adoption of holistic and systems thinking approaches, and the promotion of collaboration among different stakeholders mandated to manage WECC sectors. Until such approaches are adopted, the WECC nexus will continue to impede the country’s socio-economic development and environmental wellbeing.

The monitoring of surface-water quality followed by water-quality modeling and analysis is essential for generating effective strategies in water-resource management. However, worldwide, particularly in developing countries, water-quality studies are limited due to the lack of a complete and reliable dataset of surface-water-quality variables. In this context, several statistical and machine-learning models were assessed for imputing water-quality data at six monitoring stations located in the Santa Lucía Chico river (Uruguay), a mixed lotic and lentic river system. The challenge of this study is represented by the high percentage of missing data (between 50% and 70%) and the high temporal and spatial variability that characterizes the water-quality variables. The competing algorithms implemented belonged to both univariate and multivariate imputation methods (inverse distance weighting (IDW), Random Forest Regressor (RFR), Ridge (R), Bayesian Ridge (BR), AdaBoost (AB), Hubber Regressor (HR), Support Vector Regressor (SVR), and K-nearest neighbors Regressor (KNNR)). According to the results, more than 76% of the imputation outcomes are considered satisfactory (NSE > 0.45). The imputation performance shows better results at the monitoring stations located inside the reservoir than the ones positioned along the mainstream. IDW was the most chosen model for data imputation.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

Long-term continuous time series of SO2 emissions are considered critical elements of both volcano monitoring and basic research into processes within magmatic systems. One highly successful framework for computing these fluxes involves reconstructing a representative time-averaged SO2 plume from which to estimate the SO2 source flux. Previous methods within this framework have used ancillary wind datasets from reanalysis or numerical weather prediction (NWP) to construct the mean plume and then again as a constrained parameter in the fitting. Additionally, traditional SO2 datasets from ultraviolet (UV) sensors lack altitude information which must be assumed to correctly calibrate the SO2 data and to capture the appropriate NWP wind level which can be a significant source of error. We have made novel modifications to this framework which do not rely on prior knowledge of the winds and therefore do not inherit errors associated with NWP winds. To perform the plume rotation, we modify a rudimentary computer vision algorithm designed for object detection in medical imaging to detect plume-like objects in gridded SO2 data. We then fit a solution to the general time-averaged dispersion of SO2 from a point source. We demonstrate these techniques using SO2 data generated by a newly developed probabilistic layer height and column loading algorithm designed for the Cross-track Infrared Sounder (CrIS), a hyperspectral infrared sensor aboard the Joint Polar Satellite System’s Suomi-NPP and NOAA-20 satellites. This SO2 data source is best suited to flux estimates at high-latitude volcanoes and at low-latitude, but high-altitude volcanoes. Of particular importance, IR SO2 data can fill an important data gap in the UV-based record: estimating SO2 emissions from high-latitude volcanoes through the polar winters when there is insufficient solar backscatter for UV sensors to be used.

In this study, a dynamic mixture copula is used to estimate the marginal expected shortfall in the South African insurance sector. While other studies assumed nonlinear dependence to be static over time, our model capture time-varying nonlinear dependence between institutions and the market. In order to capture time-varying nonlinear dependence, the generalized autoregressive score (GAS) is used to model the dynamic copula parameters. Furthermore, our study implements a ranking that expresses to what degree individual insurers are systemically important in South Africa. We use daily stock return of five South African insurers listed in the Johannesburg Stock Exchange (JSE) from November 13, 2007 to June 15, 2020. We find that Sanlam and Discovery contribute the most to systemic risk, while Santam is found to be the least contributor to the overall systemic risk in the South African insurance sector. Our findings would be of paramount importance for the South African regulators as they would be informed that not only banks are systemically important, but some insurers also are systemically important financial institutions. Hence, stricter regulation of these institutions in the form of higher capital and loss absorbency requirements could be required based on the individual business activities undertaken by the company.

Consumer products contain the chemical substances that threaten human health. The modeling methods and experimental methods have been used to estimate the inhalation exposure concentration by the consumer products. The model and measurement methods have the spatial property problem and time/cost consuming problem, respectively. For solving the problems due to the conventional methodology, this study performed the feasibility of applying CFD for evaluation of inhalation exposure by comparing the experiment results and the zero-dimensional results with CFD results. To calculate the aerosol concentration, the CFD was performed by combined the 3D Reynolds averaged Navier Stoke’s equation and discrete phased model using ANSYS FLUENT. As a result of comparing the three methodologies performed under the same simulation/experimental conditions, we found the zero-dimensional spray model shows approximately 5 times underestimated inhalation exposure concentration when compared with the CFD results and measurement results in near field. Also, the results of the measured concentration of aerosols at five locations and the CFD results at the same location were compared to show the possibility of evaluating inhalation exposure at various locations using CFD instead of experimental method. The CFD results according to measurement positions can predict rationally the measurement results with low error. In conclusion, in the field of exposure science, a guideline for exposure evaluation using CFD was found that complements the shortcomings of the conventional methodology, the zero-dimensional spray model and measurement method.

We investigate the behavior of the partial derivative approach to the change of scale formula and prove relationships among the analytic Wiener integral and the analytic Feynman integral of the partial derivative for the function space integral.

In this paper, we introduce a non-invasive approach for monitoring bridge infrastructure with ground-based interferometric radar. This approach is called the mirror mode, since it utilises the flat surface of the bridge underside as a mirror to reflect the signal to a corner reflector on the ground placed opposite of the radar sensor. For proving the feasibility of this approach, a measurement campaign has been carried out at an exemplary bridge in Karlsruhe (Germany) including a radar sensor in mirror mode, a second radar sensor in the default mode and a laser profile scanner. We investigate the potential of this approach to monitor the bridge displacement in vertical direction and compare the results with the two other sensors. The derived results reveal the potential for monitoring bridge infrastructure. Finally, we propose further research aspects of this approach to analyse its capabilities and limitation in the context of non-invasive infrastructure monitoring.

This paper examines the spatial and temporal distribution of all COVID-19 cases from January to June 2020 against the underlying distribution of population in the United States. It is found that, as time passes, COVID-19 cases become a power law with cut-off, resembling the underlying spatial distribution of populations. The power law implies that many states and counties have a low number of cases, while only a few highly populated states and counties have a high number of cases. To further differentiate patterns between the underlying populations and COVID-19 cases, we derived their inherent hierarchy characterized by the ht-index. We found that the ht-index of COVID-19 cases persistently approaches that of the populations; that is, 5 and 7 at the state and county levels, respectively. Mapping the ht-index of COVID-19 cases against that of populations provides new insights into the development of the pandemic in the United States.

For the generation of representative volume elements a statistical description of the relevant parameters is necessary. These parameters usually describe the geometric structure of a single grain. Commonly, parameters like area, aspect ratio and slope of the grain relative to the rolling direction are applied. However, usually simple distribution functions like log normal or gamma distribution are used. Yet, these do not take the interdependencies between the microstructural parameters into account. To fully describe any metallic microstructure though, these interdependencies between the singular parameters need to be accounted for. To accomplish this representation, a machine learning approach was applied in this study. By implementing a Wasserstein generative adversarial network, the distribution, as well as the interdependencies could accurately be described. A validation scheme was applied to verify the excellent match between microstructure input data and synthetically generated output data.

Cell death resistance is a key feature of tumor cells. One of the main anti-cancer therapies is increasing the susceptibility of cells to death. Cancer cells have developed a capability of tumor immune escape. Hence, restoring the immunogenicity of cancer cells can be suggested as an effective approach against cancer. Accumulating evidence proposes that several anticancer agents provoke the release of danger-associated molecular patterns (DAMPs) that are determinants of immunogenicity and stimulate immunogenic cell death (ICD). It has been suggested that ICD inducers are two different types according to their various activities. Here, we review the well-characterized DAMPs and focus on the different types of ICD inducers and recent combination therapies that can augment the immunogenicity of cancer cells.

An ion exchange dialysis (IED) is used in the recovery of aluminium from residue. In this papers, the face-centered central composite design (FC-CCD) of the response surface methodology (RSM) and desirability approach is used for experimental design, modelling and process optimization of a counter flow IED system. The feed concentration, feed flowrate, sweep flowrate and sweep concentration are selected as the process variables, with the Al-transport across a Nafion 117 membrane as the target response. A total of 30 experimental runs were conducted with 6 center points. The response obtained was analysed by analysis of variance (ANOVA) and fitted to a second-order polynomial model using multiple regression analysis. The actual R2 and standard deviation of the model are 0.9548 and 0.2932 respectively. The influences of significant variables are plotted on 3D surface and contour plots. The designed variables were numerically optimized by applying the desirability function to achieve the maximum Al-transport. The optimised condition values were found to be feed concentration (1600 ppm), feed flowrate (61.76%), sweep flowrate (37.50%) and sweep concentration (0.75 N) for the 80% target response at 32hrs. Overall, the model can be used to effectively predict Al-recovery using the designed system

Recent advancements in Software Defined Networking (SDN) makes it possible to overcome the management challenges of traditional network by logically centralizing control plane and decoupling it from forwarding plane. Through centralized controllers, SDN can prevent security breach, but it also brings in new threats and vulnerabilities. Central controller can be a single point of failure. Hence, flow-based anomaly detection system in OpenFlow Controller can secure SDN to a great extent. In this paper, we investigated two different approaches of flow-based intrusion detection system in OpenFlow Controller. The first of which is based on machine-learning algorithm where NSL-KDD dataset with feature selection ensures the accuracy of 82% with Random Forest classifier using Gain Ratio feature selection evaluator. In the later phase, the second approach is combined with Gated Recurrent Unit Long Short-Term Memory based intrusion detection model based on Deep Neural Network (DNN) where we applied an appropriate ANOVA F-Test and Recursive Feature Elimination feature selection method to improve the classifier performance and achieved an accuracy of 88%. Substantial experiments with comparative analysis clearly show that, deep learning would be a better choice for intrusion detection in OpenFlow Controller.

Improvements that can be attained in seasonal climate predictions in various parts of Africa using the multimodel supersensemble scheme are presented in this study. The synthetic superensemble (SSE) used follows the approach originally developed at Florida State University (FSU). The technique takes more advantage of the skill in the climate forecast data sets from atmosphere-ocean general circulation models running at many centres worldwide including the WMO global producing centers (GPCs). The module used in this work drew data sets from the Four versions of FSU coupled model system, seven models from the DEMETER project which is the forerun to the current European Ensembles Forecast System, the NCAR Model, and the Predictive Ocean Atmosphere Model for Australia (POAMA), all making a set of 13 individual models. An archive consisting of monthly simulations of precipitation was available over all the 5 regions of Africa, namely Eastern, Central, Northern, Southern, and Western Africa. The results showed that the SSE forecast for precipitation carries a higher skill compared to each of the member models and the ensemble mean. Relative to the ensemble mean (EM), the SSE provides an improvement of 18% in simulation of season cycle of precipitation climatology. In Eastern Africa, during December-February season, a north-south gradient of precipitation prevails between Tropical East Africa and the sector of the region towards Southern Africa. This regional scale climate pattern is a direct influence of the Intertropical Convergence Zone (ITZC) across the African continent during this time of the year. The SSE emerges with superior skill scores such as lowest root mean square error above the EM and the member models, for example in the prediction of spatial location and precipitation magnitudes that characterize the see-saw precipitation pattern in Eastern Africa. In all parts of Africa, and especially Eastern Africa where seasonal precipitation variability is a frequent cause huge human suffering in due to droughts and famine, the multimodel superensemble and its subsequent improvements will always provide a forecast that out weighs the best Atmosphere-Ocean Climate Model.

Carvacrol has long been studied for its natural antifungal potential and food preservative. But the exact mode of its action remained highly complex as a general, but especially for Penicillium digitatum (P. digitatum) largely remained unexplored. Herein, a 1H-NMR-based metabolomic technique was used to investigate the antifungal mechanism of carvacrol. The metabolomic profiling data showed that alanine, aspartate, glutamate and glutathione metabolism were imbalanced in the fungal hyphae. A strong positive correlation was seen between aspartate, glutamate, alanine and glutamine, while negative correlation among glutathione and lactate. These metabolic changes revealed that carvacrol-induced oxidative stress had disturbed the energy production and amino acid metabolism of P. digitatum. Current study will improve the understanding of the metabolic changes posed by plant-based fungicides in order to control citrus fruit green mold caused by P. digitatum. Moreover, the study will provided certain experimental and theoretical basis for the development of novel citrus fruit preservatives.

G protein-coupled receptors (GPCRs) play a key role in many cellular signaling mechanisms, and must select among multiple coupling possibilities in a ligand-specific manner in order to carry out a myriad of functions in diverse cellular contexts. Much has been learned about the molecular mechanisms of ligand-GPCR complexes from Molecular Dynamics (MD) simulations. However, to explore ligand-specific differences in the response of a GPCR to diverse ligands, as is required to understand ligand bias and functional selectivity, necessitates creating very large amounts of data from the needed large-scale simulations. This becomes a Big Data problem for the high dimensionality analysis of the accumulated trajectories. Here we describe a new machine learning (ML) approach to the problem that is based on transforming the analysis of GPCR function-related, ligand-specific differences encoded in the MD simulation trajectories into a representation recognizable by state-of-the-art deep learning object recognition technology. We illustrate this method by applying it to recognize the pharmacological classification of ligands bound to the 5-HT2A and D2 subtypes of class A GPCRs from the serotonin and dopamine families. The ML-based approach is shown to perform the classification task with high accuracy, and we identify the molecular determinants of the classifications in the context of GPCR structure and function. This study builds a framework for the efficient computational analysis of MD Big Data collected for the purpose of understanding ligand-specific GPCR activity.

This paper uses event study analysis to estimate the impact of the Fed’s Quantitative Easing (QE) announcements on the mortgage market during zero lower bound period. A total of 35 QE announcements are identified and their effects are evaluated. The best-fitting IGARCH model with skewed t distribution is used to measure the QE announcement effects on daily changes of the 30-year mortgage rate, the 30-year Treasury rate and the spread between them. Announcements suggesting the start of a new round of QE reduced the mortgage rate tremendously, while the effects of further news diminished. Announcements of an increase in mortgage-backed security purchases decreased the mortgage rate more than the Treasury rate and reduced the credit risk of holding mortgage securities over Treasury securities. The long run effects of QE announcements on the mortgage rate were less than short run effects but persistent. We also find that the previous literature overestimate QE effects on interest rates in general.

In scenarios such as natural disasters and military strike, it is common for unmanned aerial vehicles (UAVs) to form groups to execute reconnaissance and surveillance. To ensure the effectiveness of UAV communications, repeated resource acquisition issues and transmission mechanism design need to be addressed urgently. In this paper, we build an information interaction scenario in a Flying Ad-hoc network (FANET). The data transmission problem with the goal of throughput maximization is modeled as a coalition game framework. Then, a novel mechanism of coalition selection and data transmission based on group-buying is investigated. Since large-scale UAVs will generate high transmission overhead due to the overlapping resource requirements, we propose a resource allocation optimization method based on distributed data content. Comparing existing works, a data transmission and coalition formation mechanism is designed. Then the system model is classified into graph game and coalition formation game. Through the design of the utility function, we prove that both games have stable solutions. We also prove the convergence of the proposed approach with coalition order and Pareto order. Binary log-linear learning based coalition selection algorithm (BLL-CSA) is proposed to explore the stable coalition partition of system model. Simulation results show that the proposed data transmission and coalition formation mechanism can achieve higher data throughput than the other contrast algorithms.

In this work we identify combinations of technological activities that signal the presence local capabilities in a country to successfully export a product. We use country-level patent and trade data to generate a multi-layer network, and we apply maximization of entropy to generate synthetic data to effectively divide signal from noise. We show that in several sectors the signal far exceed the noise. Our exercise provides robust evidence of the presence of synergies between technologies to explain trade performances in specific markets. This can be highly useful for policy makers, to inform industrial and innovation policies.

This paper proposes a procedure for predicting the actual wind speed for flow over complex terrain with CFD. It converts a time-series of wind speed data acquired from field observations into a time-series of actual scalar wind speed by using non-dimensional wind speed parameters which are determined beforehand with the use of CFD output. The accuracy and reproducibility of the prediction procedure were examined by simulating the flow with CFD with the use of high resolution (5 m) surface elevation data for the Noma Wind Park in Kagoshima Prefecture, Japan. The errors of the predicted average monthly wind speeds relative to the observed values were less than approximately 20%.

Axon guidance is a crucial process for growth of the central and peripheral nervous systems. In this study, 3 axon guidance related disorders, namely- Duane Retraction Syndrome (DRS) , Horizontal Gaze Palsy with Progressive Scoliosis (HGPPS) and Congenital fibrosis of the extraocular muscles type 3 (CFEOM3) were studied using various Systems Biology tools to identify the genes and proteins involved with them to get a better idea about the underlying molecular mechanisms including the regulatory mechanisms. Based on the analyses carried out, 7 significant modules have been identified from the PPI network. Five pathways/processes have been found to be significantly associated with DRS, HGPPS and CFEOM3 associated genes. From the PPI network, 3 have been identified as hub proteins- DRD2, UBC and CUL3.

Molenaar’s manifesto on psychology as idiographic science brought the N = 1 times series perspective firmly to the attention of developmental scientists. The rich intraindividual variation in complex developmental processes requires the study of these processes at the level of the individual. Yet, the idiographic approach is all but easy in practical research. One major limitation is the collection of short interval times series of high quality data on developmental processes. In this paper we present a novel measurement approach to this problem. We developed an online practice and monitoring system which is now used by thousands of Dutch primary school children on a daily or weekly basis, providing a new window on cognitive development. We will introduce the origin of this new instrument, called Math Garden, explain its setup, and present and discuss ways to analyze children’s individual developmental pathways.

Through the process of paradigm change (water as a resource towards water as a common), the authors examine, from a theoretic point of view, the water governability proposed by Agenda del Agua Cochabamba (AdA) – Cochabamba Water Agenda – in the Cochabamba Valley (Bolivia), identifying barriers and drivers to the process that could take place. The rise of Evo Morales in Government in 2006 suggested that policy making would somehow take a fundamental turn resulting in more poor environmental-oriented water policies. However, if that was indeed the case, the implementation of these policies remain controversial as strong power asymmetries still exist at a local level that interfere with national policies shaping the political area. The Cochabamba Water Agenda echoes this debate on the political arena and contributes a politically contested water management through a paradigm change envisaging the difficulties through its implementation. The question remains if this “political” solution to paradigm change in water management may reduce water conflicts.

This study examined the use of high dosages of ultraviolet germicidal irradiation (UVGI) (253.7 nm) to deal with various concentrations of air pollutants, such as formaldehyde (HCHO), total volatile organic compounds (TVOC), under various conditions of humidity. We also estimated the emission of ozone as a secondary pollutant of UVGI as treatment. A number of irradiation methods were applied for various durations in field studies to examine the efficiency of removing HCHO, TVOC, bacteria, and fungi. The removal efficiency of air pollutants (HCHO and bacteria) through long-term exposure to UVGI appears to increase with time. The effects on TVOC and fungi concentration were insignificant in the first week; however, improvements were observed in the second week. No differences were observed among the various irradiation methods in this study regarding the removal of HCHO and TVOC; however significant differences were observed in the removal of bacteria and fungi.

With the great development of intelligent transportation systems (ITS), travel time prediction has attracted the attentions of many researchers and a large number of prediction methods have been developed. However, as an unavoidable topic, the predictability of travel time series is the basic premise for travel time prediction has received less attention than the methodology. Based on the analysis of the complexity of travel time series, this paper defines travel time predictability to express the probability of correct travel time prediction and proposes an entropy-based method to measure the upper bound of travel time predictability. Multiscale entropy is employed to quantify the complexity of travel time series, and the relationships between entropy and the upper bound of travel time predictability are presented. Empirical studies are made with vehicle trajectory data in an express road section. The effectiveness of time scales, tolerance, and series length to entropy and travel time predictability are analysis, and some valuable suggestions about the accuracy of travel time predictability are discussed. Finally, the comparisons between travel time predictability and actual prediction results from two prediction models, ARIMA and BPNN, are conducted. Experimental results demonstrate the validity and reliability of the proposed travel time predictability.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

The self-assembly is an intriguing process of great importance in general soft matter and thus re-ceives an ever-growing scientific interest. Its most trivial example is the entropy-driven crystalli-zation of hard spheres. Past works have established the similarities and differences in the phase behavior of monomers and chains made of hard spheres. In the present work, inspired by the dif-ference in the melting points of the pure components, we study, through Monte Carlo simulations, the phase behavior of athermal mixtures composed of fully flexible polymers and individual monomers of uniform size. We analyze how the relative number fraction and the packing density affect crystallization and the established ordered morphologies. A synergetic effect is observed in the crystallization leading to synchronous crystallization of the two species. Structural analysis of the resulting ordered morphologies shows perfect mixing and thus no phase separation, which could split the system into polymer-rich and monomer-rich domains. Due to the constraints imposed by chain connectivity, the local environment of the individual spheres is systematically more spherical and more symmetric compared to the one of spheres belonging to chains. In general, increasing polymer content leads to reduction of the degree of crystallinity. According to the present findings, relative concentration is another determining factor to control the phase behavior of hard colloidal systems based on polymers.

Using desi-cow waste products like Jeevamrit, natural farming is widespread among farmers for improving soil biology and productivity. Jeevamrit enhances soil chemical and microbiological properties without needing large quantities of farmyard manure (FYM), as a sustainable farming practice with a reduced carbon footprint. Despite its traditional use, Jeevamrit faces criticism due to a lack of scientific evidence. This study investigated the comparative effect of Jeevamrit and chemical fertilizers on the growth and yield of marigold cv. Siracole. In this study mother block of marigold was raised for both summer and winter seasons. The cuttings were harvested from the mother block and then kept for rooting. The rooted cuttings were planted at monthly intervals and evaluated for flowering parameters and compared to those treated with RDF (30:20:20 N, P, and K g/m2). Soil supplied with Jeevamrit enhanced bacteria (26.33%), fungi (18.92%), and actinomycetes (31.21%) populations compared over the recommended dose of fertilizers (RDF) (i.e. N:P: K @ 30:20:20 g m-2). Jeevamrit-treated plants have marketable flower yield per square meter (3.98 %) and shelf life (9.93 %) compared to RDF. The study concludes that Jeevamrit @ 2 liter m-2 is a sustainable and effective alternative to traditional fertilizers for enhancing marigold production in the mid-hills of the Himalayan region, where natural farming is already accepted.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Efficient gene transfer and expression tool is lacking for shrimps and shrimp cells. To solve this, this study has developed a shrimp DNA virus-mediated gene transfer and expression system, consisting of insect Sf9 cells for viral packaging, shrimp viral vector of pUC19-IHHNV-PH-GUS and baculoviral vector of Bacmid or Bacmid-VP28 encoding shrimp WSSV envelope protein VP28. The pUC19-IHHNV-PH-GUS vector was constructed by assembling the genomic DNA of shrimp infectious hypodermal and hematopoietic necrosis virus (IHHNV), which had shortened inverted terminal repeats, into pUC19 backbone, and then an expression cassette of baculoviral polyhedron (PH) promoter-driven GUS reporter gene was inserted immediately downstream of IHHNV for proof-of-concept. It was found that the viral vector of pUC19-IHHNV-PH-GUS could be successfully packaged into IHHNV-like infective virions in the Sf9 cells, and gene transfer efficiency of this system had been evaluated and verified in three systems of Sf9 cells, shrimp hemolymph cells and tissues of infected shrimps, but GUS expression could be detected only in the cases when the viral vector was co-transfected or co-infected with a baculovirus of Bacmid or Bacmid-VP28 due to the Bacmid-dependence of PH promoter. Moreover, the packaging and infection efficiencies could be significantly improved when Bacmid-VP28 was used instead of Bacmid.

Bats are natural hosts for a wide variety of viruses and could therefore be the reservoir, source and spillover for several mammalian viruses, including adenoviruses. We examined faecal samples from 12 bats (five species of the family Vespertilionidae) from central Russia (Moscow Region) and found that two of them (16%) were positive for mastadenoviruses. One of the identified viruses was isolated from faeces of Nyctalis noctule and named BatAdV/MOW15-Nn19. The genome of the BatAdV/MOW15-Nn19 was 37,915 bp in length. Comparative studies have shown significant divergence of the nucleotide sequence of the BatAdV/MOW15-Nn19 genome from European mastadenoviruses, the highest genome sequence similarity was to isolate WA3301 from an Australian bat. Phylogenetic analysis, as well as a comparative analysis of the protein coding genes to homologous available from public database, showed evidence of novel species within Mastadenovirus genus (preliminary named «K»). Analysis of the short part of the DNA polymerase gene of BatAdV/MOW15-Nn19 reveals few NCBI records from Europe with high identity to the new virus, i.e. mastadenoviruses related to the new species are circulating in European bats. The partial genome of another mastadenovirus from Pipistrellus nathusii was identified, it represented bat adenovirus species B, which is widely distributed in European Vespertilionidae bats. New data on the genetic diversity of bat adenoviruses may help to better understand how they evolved in mammals and spread across Europe.

Apple replant disease (ARD) is a complex issue caused by various fungal, oomycetes pathogens and parasites which can differ in their abundance between sites within a geographic region. Knowledge of the specific etiology of ARD at a particular site is required in order to develop commercially viable soil management strategies to combat specific/individual components of the disease. In this study we analyzed the soil from six ARD sites for the presence of fungal, bacterial and oomycetes communities and plant parasitic nematodes. Five fungal, and 17 bacterial classes were differentially represented in the microbiomes from different locations. Mortierellomycetes was the most abundant fungal taxa represented followed by Sordariomycetes. Mortierella exigua a fungal endophyte was the most abundant fungal amplicon sequence variant (ASV) in the core microbiome. Proteobacteria was the most prevalent phylum identified in orchard soils. Several potential phytopathogenic fungi involved in ARD and endophytes including Fusarium oxysporum, F. solani, Nectria ramulariae, Ilyonectria robusta and Nectriaceae were identfied in the orchard soil. Pythium attrantheridium (Globisporangium attrantheridium), P. monospermum and P. ultimum (Globisporangium ultimum) were the most abundant oomycete taxa identified in these soil samples. Six different groups of plant-parasitic nematodes were found across the six orchards soil. Root-lesion nematodes, Pratylenchus spp., which are commonly associated with ARD, were identified in all orchards soil at population densities ranging from 12 to 33/100 cm3 soil. This research contributes valuable understanding of the ARD complex as the apple industry needs alternative approaches to combat the disease.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Environmental chemicals, including PFAS (per- and polyfluoroalkyl substances), pesticides, industrial chemicals, and consumer products, commonly exist as mixtures. These substances are frequently exposed or co-exposed in varying concentrations, leading to potentially hazardous health effects such as cancer in humans. Thus, understanding the dose-dependent toxicity of chemical mixtures is important for assessing health risks. In this context, comprehensive methods for assessing the toxicity and identifying the mechanisms of harmful chemical mixtures are currently lacking. Here, the dose-dependent toxicity assessments of chemical mixtures are performed in three methodologically distinct phases. In the first phase, we evaluated our machine learning method (AI-HNN) and pathophysiology method (CPTM) for predicting toxicity. In the second phase, we integrated AI-HNN and CPTM to establish a comprehensive new approach method (NAM) framework called AI-CPTM, targeted at refining prediction accuracy and providing a comprehensive understanding of toxicity mechanisms. The third phase involved experimental validations of the AI-CPTM predictions. Initially, we developed binary, multiclass classification, and regression models to predict binary, categorical toxicity, and toxic potencies, using nearly a thousand experimental mixtures. This empirical dataset was expanded with virtual mixtures compensating the lack of experimental data and broadening the scope of the dataset. For comparison, we also developed additional machine learning models based on RF, Bagging, AdaBoost, SVR, GB, KR, DT, KN, and Consensus methods. The models achieved overall accuracies of over 80% with AUC values exceeding 90%. The regression models achieved an R2 >0.88. In the second phase, we innovatively integrated HNN-derived toxicity predictions with Z-scores from CPTM, resulting method called AI-CPTM. In the final phase, we demonstrated the superior performance of AI-CPTM through rigorous literature and statistical performance validations. Additionally, the predictive capability of AI-CPTM, including for PFAS mixtures and their interaction effects, was demonstrated by experimental validations using dose-response zebrafish embryo toxicity assays. Overall, the AI-CPTM approach significantly improves upon the limitations of standalone models and has shown extensive enrichments in the identification of toxic chemicals and mixtures. Further experimental studies involving human cell models, patient-derived xenografts, and investigations into the toxicity of multiple mixtures are currently underway.

This study aims to demonstrate the possibility of incorporating a natural antioxidant biomolecule, into polymeric porous scaffolds. To this end, Poly-L-Lactic Acid (PLLA) scaffolds were produced using the Thermally Induced Phase Separation (TIPS) technique and additivated with different amounts of Rosmarinic Acid (RA). The scaffolds, with a diameter of 4 mm and a thickness of 2 mm, were characterized with a multi-analytical approach. Specifically, Scanning Electron Mi-croscopy analyses demonstrated the presence of an interconnected porous network, character-ized by a layer of RA at the level of the pore’s surfaces. Moreover, the presence of RA biomole-cules increased the hydrophilic nature of the sample, as evidenced by the decrease in contact angle with water from 128° to 76°. This approach is cost-effective, and it could be customized with different biomolecules, offering the possibility of producing porous polymeric structures con-taining antioxidant molecules. These scaffolds meet the requirements of tissue engineering and could be offered a potential solution to reduce inflammation associated with scaffold implantation thus improving tissue regeneration.

Climate change is one of the most concerning global issues and has the potential to influence every aspect of human life. Like different components of society, it can impose significant adverse impacts on pavement infrastructure. Although several research efforts have focused on studying the effects of climate change on natural and built systems, its impact on pavement performance has not been studied extensively. Due to the weather effect the lifetime of pavement is getting lower on the other hand maintenance cost is getting higher and higher. The data has been collected from LTTP website and as a site The State of Texas has been considered. The primary objective of this project is to quantify the effect of temperature as well as precipitation changes on pavement response and performance prediction using the ARIMA model and develop a logistic regression model to analyze the forecast data.

The product of ozonolysis, Glycero-(9,10-trioxolane)-trioleate (ozonide of oleic acid triglyceride, [OTOA]), was incorporated into polylactic acid/polycaprolactone (PLA/PCL) blend films in the amount of 1, 5, 10, 20, 30, and 40% w/w. The morphological, mechanical, thermal and antibacterial properties of the biodegradable blend after the OTOA addition were studied. According to DSC and XRD data, the crystallinity degree of PLA/PCL+OTOA films tended to decrease with increase in OTOA content that could be explained by its plasticizing effect. Morphological analysis showed that the structure of the films with the OTOA concentration above 20% drastically changed. Specifically, the interface between the PLA/PCL matrix and OTOA was formed, thereby forming a capsule with the embedded antibacterial agent. The moisture permeability of the resulting PLA/PCL+OTOA films decreased due to the formation of uniformly distributed hydrophobic amorphous zones that prevents water penetration. This architecture affects the tensile characteristics of the films: strength decreases to 5.6 MPa, elastic modulus E by 40%. The behavior of film elasticity is associated with the redistribution of amorphous regions in the matrix. Additionally, PLA/PCL+OTOA films with 20, 30 and 40% of OTOA showed good antibacterial properties on Pseudomonas aeruginosa, Raoultella terrigena (Klebsiella terrigena) and Agrobacterium tumefaciens. Developed PLA/PCL+OTOA films could be used as packaging materials and wound dressings. By variation of the OTOA content, it is possible to tailor the physical-chemical and antibacterial properties of the developed films for various applications.

Since sensor-based perception systems are used in autonomous vehicle applications, validating such systems is imperative to guarantee the robustness of the systems before they are being put to use. In this study, a comprehensive corruption-related simulation-based robustness verification and enhancement process for sensor-based perception systems is proposed. Firstly, we present a methodology and scenario-based corruption generation tools for creating diverse simulated test scenarios that can analogously represent real-world traffic environments, especially considering corruption types related to safety concern. Then, an effective corruption similarity filtering algorithm is proposed to remove corruption types with high similarity and identify the representative corruption types to represent all considered corruption types. As a result, we can generate efficient corruption-related robustness test scenarios with less testing time and good scenario coverage. Subsequently, we perform the vulnerability analysis of object detection models to identify model weaknesses and construct an effective training dataset for model vulnerability enhancement. This enhances the tolerance of object detection models to weather and noise-related corruptions, ultimately improving the robustness of the perception system. We employ case studies to demonstrate the feasibility and effectiveness of the proposed robustness verification and enhancement procedures. Additionally, we explore the impact of different "similarity overlap threshold" parameter settings on scenario coverage, effectiveness, scenario complexity (size of training and testing datasets), and time costs.

Background: Patients’ effective hand hygiene helps to reduce healthcare-associated infections, prevents the spread of nosocomial infections and communicable diseases, such as COVID-19. This study aimed to describe effective hand hygiene decisions based on the Health Action Process Ap-proach (HAPA) and whether this pattern is invariant for mental health. Methods: Data were collected cross-sectionally from patients who had previously been admitted to a hospital (N=279; study 1) and longitudinally from psychosomatic rehabilitation patients (N=1,073; study 2). The fit of the HAPA framework and changes in hand hygiene decisions regarding com-pliance, as well as social-cognitive variables of the HAPA, and mental health status were examined. Results: The trimmed HAPA framework fitted the data well (χ2=27.1, df=12, p<.01, CMIN/df=2.26, CFI=.97, RMSEA=.08). According to multi-group structural equation modeling, the HAPA model with hand hygiene behavior were found to be invariant with regard to mental health. Conclusion: The trimmed HAPA framework revealed to be a generic framework in explaining so-cial-cognitive processes relating to hand hygiene decisions. Helping individuals to perform hand hygiene recommendation requires intention formation and bridging the intention-behavior gap. This can be done by promoting planning and self-efficacy. All processes appear generic to partic-ipants with and without mental health challenges.

In this paper we introduce the concept of Nano Beta Closure, Nano Beta Interior and study the relationship between them also study some of their properties. Based on these notions we introduced the topological Approach to Decision Making and Its Application in the Medical Field" which describes the use of topological methods in decision-making, specifically through the utilization of nano beta closure and nano beta interior. These mathematical tools are applied in the medical field to improve diagnostic accuracy and aid in treatment planning. The authors demonstrate the effectiveness of this approach through a case study on the diagnosis of Chronic Kidney. The results show that the topological approach using nano beta closure and nano beta interior provides a reliable and accurate method for medical decision-making. Finally, we introduce a medical application for disease groups patients of with chronic kidney. To identify the main causative agent of kidney disease. where using this approach, the medical team can identify the specific areas of the kidney that are affected by the infection, as well as the extent of damage and any potential complications. This information is used to create an individualized treatment strategy that is customized to meet the specific requirements of the patient. and medical history. We write an algorithm that can be a helpful tool for doctors to utilize in diagnosing infection disease Chronic Kidney infections. By utilizing this approach, clinicians can provide accurate diagnoses, develop effective treatment plans, and ultimately improve patient outcomes. finally, we show that fractals hold significant importance in future nano topological generation of the human factor. Their unique properties and self-similar patterns offer insights into the complex organization of biological systems and provide a foundation for designing advanced Nanosystems.

In this paper, we propose a novel approach to utilize silicon nanowires as high-sensitivity pH sensors. Our approach works based on fixing the current bias of silicon nanowires Ion Sensitive Field Effect Transistors (ISFETs) and monitor the resulting drain voltage as the sensing signal. By fine tuning the injected current levels, we can optimize the sensing conditions according to different sensor requirements. This method proves to be highly suitable for real-time and continuous measurements of biomarkers in human biofluids. To validate our approach, we conducted experiments, with real human sera samples to simulate the composition of human interstitial fluid (ISF), using both the conventional top-gate approach and the optimized constant current method . We successfully demonstrated pH sensing within the physiopathological range of 6.5 to 8, achieving an exceptional level of accuracy in this complex matrix. Specifically, we obtained a maximum error as low as 0.92\% (equivalent to 0.07 pH unit) using the constant-current method at the optimal current levels (1.71\% for top-gate). Moreover, by utilizing different pools of human sera with varying total protein content, we demonstrated that the protein content among patients does not impact the sensors' performance in pH sensing. Furthermore, we tested real-human ISF samples collected from volunteers. The obtained accuracy in this scenario was also outstanding, with an error as low as 0.015 pH unit using the constant-current method and 0.178 pH unit in traditional top-gate configuration.

The objective of this study was to apply simulation and computational intelligence techniques using artificial intelligence and genetic algorithm for economic and environmental optimization of the reverse network (manufacturers, waste managers and recyclers in São Paulo, Brazil) of waste electrical and electronic equipment (WEEE) to promote circular economy. For the economic evaluation, the reduction of: fuel, drivers, insurance, depreciation, maintenance and charges was considered and for the environmental evaluation, the environmental impact was measured in the abiotic, biotic, water, land, air and greenhouse gases compartments. It is concluded that the optimized structure of the WEEE reverse chain for São Paulo, Brazil reduced the number of collections, making the most of the cubage. It also generated economic and environmental gains, contributing to the strategic actions of the circular economy. Thus, the proposed simulation allows replication in organizational practice, mainly to meet the 2030 agenda on reducing the carbon footprint generated in transport in large cities. Thus, this study can guide companies on structuring the reverse WEEE chain in São Paulo, Brazil for economic and environmental optimization, a relevant aspect considering the exponential generation of WEEE, requiring the implementation of the national solid waste policy, and subsequently the signature of the electronics sector agreement in São Paulo.

The ultimate aim of dynamic load balancing in cloud computing systems is to maximise the efficiency with which resources are utilised and workloads are distributed. Given that load balancing is a multi-objective process and that response time is a priority, the Harris hawk optimisation (HHO) algorithm was developed as a unique solution for dynamic load balancing. Based on burden distribution and resource utilisation, the HHO algorithm is responsible for dynamically assigning workloads to virtual machines (VMs). Through iterative interactions and position updates, the hawks investigate the solution space, determine the optimal method for dividing the work, and adapt to the ever-changing conditions of the workload. The HHO algorithm has been demonstrated to be effective and efficient in the management of dynamic load balancing via a series of experimental evaluations and comparisons with other load-balancing approaches. These discoveries have led to quicker response times and more efficient resource utilisation. Utilising the collaborative search behaviour of hawks, this technique provides a solution that is both practicable and effective for addressing load balancing concerns in dynamic scenarios.

Life is supported by metabolism, a vital physiological activity. It guarantees enough energy available to power every cellular activity. The primary cellular substrate, glucose, is where the majority of the energy needed by the cell to support all other life activities and the growth of living creatures is derived. The quality of life is greatly impacted by any disease or flaw that alters the metabolism of glucose. There is no known cure for the metabolic illness known as diabetes. As diabetes is so varied, the only effective treatments would be based on precision medicine and a molecular strategy. This review covers a wide range of topics, including the ability to recognize the various forms of diabetes, the anthropogenic and genetic influence of the cause of diabetes, the severity of the various forms of diabetes, its potential existential risk, the disease burden, and clinical methods for diagnosing them. The most recent research goes on to recommend ways to ameliorate the disease, including diet-based management, biotherapies, and other individual lifestyle choices. Futuristic therapy using molecular biology approach was suggested. Recent research found a direct correlation between an individual's lifestyle and the rate of gene mutation in diabetes. There is an existential risk associated with the sickness as the rate of the spread of the disease among population globally is faster than the world's population growth rate. It is possible to think of diabetes as a silent pandemic.

Marine macroalgae have garnered significant attention in the field of cosmeceutical research due to their rich abundance of bioactive compounds. These compounds offer remarkable skin benefits without inducing any adverse effects on human health, such as cytotoxicity, reproductive toxicity, genotoxicity, mutagenicity, or carcinogenicity. Among the various bioactive compounds found in brown algae, phenolic compounds exhibit diverse chemical structures and are present in high concentrations. In addition to phenolic compounds, brown algae also contain terpenoids, bro-mophenols, mycosporine amino acids (MAAs), and flavonoids, with the well-studied poly-phenol compound, phlorotannin, being particularly prominent. Marine macroalgae further possess an array of pigments derived from their natural pigmentation, including chlorophylls, carotenoids (such as fucoxanthin and β-carotene), phycobiliproteins (such as phycoerythrin and phycocyanin), and melanin. These pigments have been extensively investigated for their potential cos-meceutical applications. The phenolic compounds and pigments derived from marine macroalgae have been thoroughly studied for their beneficial effects on the skin, including skin whitening, moisturizing, photoprotection, anti-aging, anti-wrinkle, anti-melanogenic, and anti-oxidant properties. This comprehensive review aims to explore the extraction, characterization, and skin cosmetic effects of phenolic compounds and pigments derived from marine macroalgae, as documented in the existing literature, thereby enhancing our understanding of their therapeutic potential.

Effortful control (EC) describes individual differences in self-regulation, with a strong attentional basis. Moreover, during early childhood EC has a central role on children’s socio-emotional adjustment and academic achievement. The aim of the current study was to predict the development of EC at 36 months of age from early attentional and environmental measures taken in infancy using a machine learning approach. A sample of 75 infants participated in a longitudinal study running different waves of data collection at 6, 9 and 36 months of age. Attentional tasks were administered at 6 months of age and two additional measures were collected at 9 months of age. Parents reported household environment variables during wave 1, and their child’s EC at 36 months. A machine -learning algorithm was implemented to identify children with low EC scores at 36 months of age. An “attention only” model showed greater predictive sensitivity than the “environmental only” model. However, a model including both attentional and environmental variables was able to classify the groups (Low-EC vs Average-to-High EC) with 100% accuracy. Sensitivity analyses indicate that socio-economic variables together with attention control processes at 6-months, and self-restraint capacity at 9-months, are the most important predictors of EC. Results suggest a foundational role of executive attention processes in the development of EC in complex interaction with household environment and provide a new tool to identify early markers of socio-emotional regulation development.

Despite a rapid rise in NBS development in recent years, the methods for evaluating NBS still have certain gaps. We propose an approach based on a combination of remote sensing data and meteorological variables to reconstruct the spatio-temporal variation of net ecosystem exchange from eddy-covariance stations. Lagrangian particle dispersion model was used for upscaling of satellite images and flux towers. We trained data-driven models based on kernel methods separately for each selected land cover class. The results suggest that the proposed approach to quantifying carbon exchange on a medium-to-large scale by blending eddy covariance flux data with moderate resolution satellite and weather data provides a set of key advantages over previously deployed methods: (1) scalability, achieved via the validation design based on a separate set of eddy covariance stations; (2) high spatial and temporal resolution due to use of the Landsat imagery; (3) robust and accurate predictions due to improved data quality control, advanced machine learning techniques, and rigorous validation. The machine learning models yielded high cross-validation results. Overall we present here globally scaled technology for the land sector based on high resolution remote sensing imagery, meteorological variables, and direct carbon flux measurements of eddy covariance flux stations.

Precision medicine emphasizes fine-grained diagnostics, taking individual variability into account to enhance treatment effectiveness. Parkinson's Disease (PD) heterogeneity among individuals is a proof that disease subtypes exist, and assigning individuals to subgroups is necessary for a better understanding of disease mechanisms and designing precise treatment approaches. The purpose of this study was to identify PD subtypes using RNA-Seq data in a combined pipeline including unsupervised machine learning, bioinformatics, and network analysis. 210 post mortem brain RNA-Seq samples from PD (n = 115) and Normal Controls (NC, n = 95) were obtained with a systematic data retrieval following PRISMA statements and a fully data-driven clustering pipeline was performed to identify PD subtypes. Bioinformatics and Network analyses were performed to characterize the disease mechanisms of the identified PD subtypes and to identify target genes for drug repurposing. Two PD clusters were identified and 42 DEGs were found (p.adjusted ≤ 0.01). PD clusters had significantly different gene network structures (p &lt; 0.0001) and phenotype-specific disease mechanisms, highlighting the differential involvement of the Wnt/β-catenin pathway regulating adult neurogenesis. NEUROD1 was identified as a key regulator of gene networks and ISX9 and PD98059 were identified as NEUROD1-interacting compounds with disease-modifying potential, reducing the effects of dopaminergic neurodegeneration. This hybrid data analysis approach could enable precision medicine applications by providing insights for the identification and characterization of pathological subtypes. This workflow has proven useful on PD brain RNA-Seq, but its application to other neurodegenerative diseases is encouraged.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

Background/Purpose: Over the last two decades, malaria has remained a major worldwide public health concern, especially in the developing countries leading to high morbidity and mortality among children. Nigeria is the world most burdened malaria endemic nation, contributing more than a quarter of global malaria cases. This study determined the prevalence of malaria among children 6-59 months in Nigeria, and the effects of individual and contextual factors. Methods: The study utilized data from 2018 Nigeria Demographic and Health Survey (NDHS) involving a weighted sample size of 10,185 children who were tested for malaria using rapid diagnostic test (RDT). Given the hierarchical structure of the data set, such that children at level-1 are nested in community at level-2, and nested in states and Federal Capital Territory (FCT) at level-3, multilevel mixed effect logistic regression models were used for the analysis. Results: The proportion of children 6-59 months of age in Nigeria that had malaria fever positive as assessed by RDTs was 35.5% (3,418/10185), (CI: 33.9-37.1). Kebbi State had the highest proportion of children 6-59 months who were malaria positive, 77.6%, (CI: 70.2-83.5), followed by Katsina State, 55.5%, (CI: 47.7-63.1). The Federal Capital Territory (FCT), Abuja had the proportion of 29.6%, (CI: 21.6-39.0), malaria positive children of 6-59 months of age. Children between the age of 48 and 59 months were 2.68 times more likely to have malaria fever than children 6-11 months of age (AOR=2.68, 95% CI: 2.03-3.54). Also, children from the rural area (AOR= 2.12, 95% CI: 1.75-2.57), were more likely to suffer from malaria infection compare with children from urban area. Conclusion: The study identified some individual and contextual predictors of malaria among children in Nigeria. These factors are areas that need to be considered for policy designs and implementations toward control and total elimination of malaria-related morbidity and mortality among children in Nigeria.

.Most of the accident cases at work are caused by unsafe behaviour. Scholars have thus extensively researched factors of safe behavior.Safety leadership is stated as the most effective factor in safety behaviour. Besides, safety knowledge and safety attitudes are also found to influence safety behaviour. The purpose of this paper is to investigate the nature of the relationship between safety leadership, safety knowledge, safety attitude, and safety behavior, which has been found to be limited or rare in previous research.A self-administered questionnaire was applied and was distributed randomly to 140 SME manufacturing workers and they were analysed using the structural equation modelling partial least squares (PLS-SEM). The results prove that safety leadership has a significant effect on safety knowledge, safety attitude, and safety behaviour, with safety knowledge and safety attitude mediating the safety leadership-safety behaviour relationship. Consequently, the results provide a more in-depth view of the relationship between safety leadership and safety knowledge-attitude-behaviour via adapting social-cognitive theory and social learning theory in solving safety issues in SME. This study also provides a starting point for researchers to better understand how effective safety leadership is provided by supervisors in terms of improving worker safety and safety knowledge-attitude-behaviour.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

Inside hippocampal circuits, neuroplasticity events that individual cells may undergo during synaptic transmissions occur in the form of Long Term Potentiation (LTP) and Long Term Depression (LTD). The high density of NMDA receptors expressed on the surface of the dendritic CA1 spines confers to hippocampal CA3-CA1 synapses, the ability to easily undergo NMDA-mediated LTP and LTD, that is essential for some forms of explicit learning in mammals. Providing a comprehensive kinetic model that can be used for running computer simulations of the synaptic transmission process is currently a major challenge. Here, we propose a compartmentalized kinetic model for CA3-CA1 synaptic transmission. Our major goal was to tune our model in order to predict the functional impact caused by disease associated variants of NMDA receptors related to severe cognitive impairment. Indeed, for variants Glu413Gly and Cys461Phe, our model predicts negative shifts in the glutamate affinity and changes in the kinetic behavior, consistent with experimental data. These results pinpoint to the predictive power of this multiscale viewpoint, which aims to integrate the quantitative kinetic description of large interaction networks typical of system biology approaches with a focus on the quality of few, key, molecular interactions typical of structural biology ones.

Background: The Balaruc-les-Bains’ thermal mud was found to be colonized predominantly by microorganisms, with cyanobacteria constituting the primary organism in the microbial biofilm observed on the mud surface. The success of cyanobacteria in colonizing this specific ecological niche can be explained in part by their taxa-specific adaptation capacities, and also the diversity of bioactive natural products that they synthesize. This array of components has physiological and ecological properties that may be exploited for various applications.

The presented study demonstrates the bi-sensor approach suitable for rapid and precise up-to-date mapping of forest canopy gaps for the larger spatial extent. The approach makes use of UAV RGB images on smaller areas for highly precise forest canopy mask creation. Sentinel-2 was used as a scaling platform for transferring information from UAV to a wider spatial extent. The various approaches of the improvement of the predictive performance were examined: (I) the highest R2 of the single satellite index was up to 0.57, (II) the highest R2 using multiple features obtained from the single date, S-2 image was 0.624 and, (III) the highest R2 on the multi-temporal set of S-2 images, was 0.697. Satellite indices such as ARVI, IPVI, NDI45, PSSRa, MCARI, CI, RI, and NDTI were the dominant predictors in most of the ML algorithms. The more complex ML algorithms such as SVM, Random Forest, GBM, XGBoost, and Catboost that provided the best performance on the training set exhibited weaker generalization capabilities. Therefore, a simpler and more robust Elastic Net algorithm was chosen for the final map creation.

This study aims to evaluate a new approach in modeling gully erosion susceptibility based on deep learning neural network (DLNN) model, ensemble Particle swarm optimization (PSO) algorithm with DLNN (PSO-DLNN) and comparing these approaches with common artificial neural network (ANN) and support vector machine (SVM) models in Shiran watershed, Iran. For this purpose, 13 independent variables affecting gully erosion susceptibility in the study area, including altitude, slope, aspect, plan curvature, profile curvature, drainage density, distance from river, land use, soil, lithology, rainfall, , stream power index (SPI), topographic wetness index (TWI), were prepared. Also, 132 gully erosion locations were identified during field visits. Data for modeling were divided into two categories of training (70%) and testing (30%). Receiver operating characteristic (ROC) parameters including sensitivity, specificity, negative predictive value (NPV), positive predictive value (PPV) and area under curve (AUC) were used to evaluate the performance of the models. The results showed that, the AUC values from ROC with considering testing datasets of PSO-DLNN is 0.89 and which is associated with superb accuracy. Rest of the models also associated with optimal accuracy and near about PSO-DLNN model; the AUC values from ROC of DLNN, SVM and ANN for testing datasets are 0.87, 0.85 and 0.84 respectively. The PSO algorithm has updated and optimized the weights of DLNN model, and as a result, the efficiency of this model in predicting gully erosion susceptibility has increased. Therefore, it can be concluded that the use of DLNN model and its ensemble with PSO algorithm can be used as a novel and practical method in predicting the susceptibility of gully erosion that helps planners and managers in managing and reducing the risk of this phenomenon.

In France, veterinarians are allowed to both prescribe and deliver drugs, a questioned situation from the perspective of antimicrobial use (AMU) reduction in order to ovoid AM resistance (AMR). This situation places veterinarians in direct commercial relationships with the pharmaceutical industry. The present study aims to describe contracts between pharmaceutical companies and veterinarians during the period 2008-2014. 382 contracts related to 47 drugs belonging to the 8 main pharmaceutical firms (2,320 observations) in France were collected. The price per unit after rebate (PUR) was calculated for each drug and contract. The descriptive analysis demonstrated a high disparity between the content of contracts and the way in which they are presented. A linear regression was then used to explain the PUR with the explanatory variables, which were the yearly purchase objective, the year, the type of drug and type of rebate. The decrease in PUR for each extra €1,000 objective per drug category was established to be €0.061 per 100 kg body weight (BW) for anticoccidiosis treatments, €0.029 per 100 kg BW for anti-inflammatories, €0.0125 per 100 kg BW, €0.0845 per animal for antiparasitics, and €0.031 per animal for intramammary antimicrobials. Applying agency theory shows that veterinarians can be considered the agents in case of monopolistic or oligopolistic situations of pharmaceutical firms, they are considered the principals otherwise. Policies that focus on maintaining veterinarians as principals may help reach the better societal benefit since this helps them maintain access to veterinary services throughout the region at low public cost while being liable for AMU.