This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Low Emission Zone (LEZ) is an important mechanism to limit the negative environmental impact of traffic pollution in an urban area. Car traffic in the zone is strictly regulated to meet certain technical and environmental criteria. Such solutions of urban environment protection are gaining popularity, especially in European conurbations. Nowadays there are above 300 zones in Europe, mostly established in Italy and Germany. So far there are no LEZs in Eastern and Central European countries. However, the Warsaw authorities are just discussing launching of a LEZ in the city in 2024. According to the ongoing project, the zone is to be launched gradually, in five phases between 2024 and 2032, with the traffic criteria being tightened accordingly. The progressive emission reductions of the predominant pollutants in LEZ in consecutive phases were estimated on the basis of the Real Driving Emissions (RDE) test, carried out in 2020 by the ICCT. The gradually reduced emissions of NOx and PM were subsequently utilized as the input dataset for the regional CALPUFF model predictions, to calculate concentrations of these main traffic-induced pollutants within the LEZ area. The direct effect of the zone activation is reduction of air pollution in the urban center, which is mostly exposed to the pollution risk due to heavy traffic. Computer simulations reveal that implementation of the zone in the case of Warsaw will result in a quite significant reduction of NOx concentrations within the LEZ, such that its mean concentration in the zone becomes comparable to the rest of the conurbation. However, it will bring only a slight reduction of PM2.5 concentrations. This situation is due to the long-standing dominance of coal combustion in the Polish economy, which also applies to the urban municipal sector. As a consequence, particulate matter emissions of this sector are clearly predominant over the road traffic contribution. Balance can be achieved once the ongoing de-carbonization of the national economy has been completed.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

The assessment of an organization/product's environmental footprint is based on the protocols developed by the Joint Research Centre of the European Union, which take into account 16 impact categories. Among the categories covered are toxicity to freshwater ecosystems and to humans. Standard protocols use only chemical parameters as input data, preventing the true impact of entire complex mixtures, such as emissions discharged into the environment, from being determined. Biological assays allow us to bridge this gap: in the current study, assays were used to determine baseline toxicity towards aquatic organisms (green algae, luminescent bacteria, and crustaceans) as well as specific toxicity (mutagenicity and carcinogenicity). Expected impacts were compared using two approaches (standard and bioassay-centered results obtained are not always in line and, in general, the traditional method underestimates impacts). This demonstrates the importance of these assays and suggests that they be used in LCA (Life Cycle Assessment) protocols as well.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

Magnetorheological elastomers (MREs) are a type of smart material that can change their mechanical properties in response to external magnetic fields. These unique properties make them ideal for various applications, including vibration control, noise reduction, and shock absorption. This paper presents an approach for modeling the impact behavior of MREs. The proposed model uses a combination of exponential functions arranged in a multi-layer Preisach model to capture the nonlinear behavior of MREs under impact loads. The model is trained using particle swarm optimization (PSO) and validated using experimental data from drop impact tests conducted on MRE samples under various magnetic field strengths. The results demonstrate that the proposed model can accurately predict the impact behavior of MREs, making it a useful tool for designing MRE-based devices that require precise control of their impact response. The model's response closely matches the experimental data, with a maximum prediction error of 10% or less. Furthermore, the interpolated model's response shows good agreement with the experimental data, with a maximum percentage error of less than 8.5%.

The construction industry is responsible for 40 to 45% of primary energy consumption in Europe alone. Therefore, it is essential to find new materials with a lower environmental impact in order to attain sustainable housing. This study aims to determine and compare the environmental impact of two clay samples forming a basis for the manufacture of traditional brick, a standard material in building construction; traditional red clay brick and a brick based on clay mixed with a biological ingredient. The samples of fired clay were manufactured at the laboratory scale, the results being valid exclusively as indicators for the extrapolation of the analysis to other studies. The results of the environmental impact of these formulations have been examined through an evaluation of life-cycle analysis (LCA), observing that the incorporation of biological pore forming agents led to a decrease of around 15 to 20% of all impact categories studied. Thus, the suitability of using biological-based additives in clay bricks was confirmed both for their constructive characteristics (lighter material) and increased energy efficiency (better thermal insulation) considering the environmental point of view.

Artificial intelligence (AI) has emerged as a transformative force in retail operations, promising significant advancements in efficiency, customer engagement, and competitive positioning. This research explores the integration of AI in retail, focusing on its potential benefits, challenges, and future trends. Through a comprehensive analysis, the study identifies key motivations for AI adoption, such as enhancing operational efficiency, optimizing inventory management, and personalizing customer interactions. Retailers are increasingly leveraging AI to streamline processes and gain insights into consumer behavior, which allows for more strategic decision-making and improved customer experiences. However, the implementation of AI is not without its obstacles. High costs, the need for specialized skills, and concerns about data privacy and ethical use of AI present substantial challenges. The impact of AI on employment, including job displacement and the necessity for reskilling, is also a critical consideration. Future trends suggest that AI will continue to drive innovation in retail, with developments in AI-powered analytics, autonomous retail solutions, and sustainability initiatives shaping the industry’s future. The study highlights the importance of addressing these challenges and ethical considerations to fully realize the potential of AI in retail. The findings emphasize the need for retailers to adopt a strategic approach to AI integration, balancing innovation with responsible practices to achieve long-term success. Overall, this research provides valuable insights into the evolving role of AI in retail and offers a foundation for understanding the complexities and opportunities associated with its adoption.

Even though, graphene family materials (GFMs) hold great promise for various applications, there are still significant knowledge gaps in ecotoxicology and environmental risk assessment associated with their potential environmental impacts. Here, we provide a critical perspective on published ecotoxicity studies of GFMs based on a meticulous bibliometric research. Analysis of the available data revealed that to date, ecotoxicity studies with GFMs have been carried out predominantly using freshwater species (82%), while their effects on marine or terrestrial or-ganisms are understudied. Three groups of organisms were found dominating ecotoxicological research: fish (39%), algae (20%) and arthropoda (20%) predominantly applying small, planktonic crustaceans. It was also revealed that despite their widespread detection in different environ-mental compartments the potential impacts of GFMs in complex test systems with hierarchical trophic organisation or in trophic transfer studies are significantly under-represented. One of the main causes was identified as the difficulties in the physicochemical characterisation of GFMs in complex terrestrial test systems or in aquatic micro- and mesocosm studies containing a sediment phase. The lack of tools for adequate characterisation of GFMs in these complex test systems may discourage researchers from conducting experiments under environmentally relevant test condi-tions. However, in the coming years, fundamental research about these complex test systems will con-tinue to better understand the mechanism behind GFMs toxicity affecting organisms in different environmental compartments and to ensure their safe and sustainable use in the future.

The spectra currently emerging from modern ground- and space-based astronomical instruments are of exceptionally high quality and resolution. To meaningfully analyse these spectra researchers utilise complex modelling codes to replicate the observations. The main inputs to these codes are atomic data such as excitation and photoionisation cross sections as well as radiative transition probabilities, energy levels and line strengths. In this publication the current capabilities of the numerical methods and computer packages used in the generation of these data are discussed. Particular emphasis is given to Fe-peak species and the heavy systems of tungsten and molybdenum. Some of the results presented to highlight certain issues and/or advances have already been published in the literature, while other sections present, for the first time, new recently evaluated atomic data.

This study investigates the impact of the economic downturn induced by the COVID-19 pandemic on nutritional health disparities among women. The research aimed to understand how economic challenges have influenced dietary choices, access to nutritious food, and overall nutritional well-being in different socioeconomic groups of women.Utilizing a mixed-methods approach, the study combined quantitative data from national health and economic databases with qualitative insights from interviews conducted with a diverse group of women. The quantitative analysis focused on trends in nutritional health indicators and economic variables pre- and post-pandemic. Simultaneously, the qualitative component explored personal experiences and perceptions related to nutrition and economic hardships during the pandemic.The findings revealed a significant correlation between the economic downturn and worsening nutritional health among women, especially in low-income and marginalized communities. Women in these groups reported reduced access to healthy food options, increased reliance on less nutritious food due to budget constraints, and a general decline in dietary quality. This decline was less pronounced in higher-income groups, highlighting a clear disparity.Moreover, the study observed that the pandemic exacerbated pre-existing nutritional inequalities, with vulnerable groups experiencing a more pronounced impact. The research also noted that community support systems and public health interventions played a crucial role in mitigating some of these effects.In conclusion, the COVID-19 pandemic has not only posed a direct health challenge but has also indirectly affected women's nutritional health through economic strain. The study underscores the need for targeted nutritional support and economic policies that prioritize the health of women, particularly those from socioeconomically disadvantaged backgrounds.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient?Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001).Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient? Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001). Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

Due to remarkable socioeconomic development, an increasing number of karst rocky desertification areas have been severely affected by human activities in southern China. Effectively analyzing human activities in karst rocky desertification areas is a critical prerequisite for managing and restoring areas with tremendous negative impacts from desertification. At present, a timely and accurate way of quantifying the spatiotemporal variations of human activities in karst rocky desertification areas is still lacking. In this communication, we attempted to quantify human activities from the corrected NPP-VIIRS nighttime light data from 2012 to 2018 based on statistical analysis. The results show that a significant increase of night lights could be clearly identified during the study period. The total nighttime lights (TL) related to severe karst rocky desertification (S) were particularly concentrated in Guizhou and Yunnan. The nighttime light intensity (LI) related to the S areas in Chongqing were the strongest due to its rapid socioeconomic development. The annual growth rate of nighttime lights (GL) has been slow or even negative in Guangdong because of its various karst rocky desertification restoration programs. This communication could provide an effective approach for quantifying human activities and provide useful information about where prompt attention is required for policy-making on the restoration of the karst rocky desertification areas.

This paper aims at addressing the exploitation of solid-state carriers for hydrogen storage, with attention paid both to the technical aspects, through a wide review of the available integrated systems, and to the social aspects, through a preliminary overview of the connected impacts from a gender perspective. As for the technical perspective, carriers to be used for solid-state hydrogen storage for various applications can be classified into two classes: metal and complex hydrides. Related crystal structures and corresponding hydrogen sorption properties are reviewed and discussed. Fundamentals of thermodynamics of hydrogen sorption evidences the key role of the enthalpy of reaction, which determines the operating conditions (i.e. temperatures and pressures). In addition, it rules the heat to be removed from the tank during hydrogen absorption and to be delivered to the tank during hydrogen desorption. Suitable values for the enthalpy of hydrogen sorption reaction for operating conditions close to ambient (i.e. room temperature and 1-10 bar of hydrogen) are close to 30 kJ·molH2 1. The kinetics of hydrogen sorption reaction is strongly related to the microstructure and to the morphology (i.e. loose powder or pellets) of the carriers. Usually, kinetics of hydrogen sorption reaction is rather fast, and the thermal management of the tank is the rate determining step of the processes. As for the social perspective, various scenarios for the applications in different socio-economic contexts of solid-state hydrogen storage technologies are described. As it occurs with the exploitation of other renewables innovative technologies, a wide consideration of the social factors connected to these processes is needed to assess the extent to which a specific innovation might produce positive or negative impacts in the recipient socio-economic system and to explore the potential role of the social components and dynamics in fostering the diffusion of the innovation itself. Attention has been addressed to the gender perspective, in view of the enhancement of hydrogen-related energy storage systems, intended both in terms of the role of women in triggering the exploitation of hydrogen-based storage as well as to the impact of this innovation in their current conditions, at work and in daily life.

Groundwater habitats in the Dinaric Karst are home to the only known cave-adapted genus of bivalve mollusks, which currently survives as three distinct species with a highly fragmented distribution. Over the past few decades, Congeria populations suffered a steep decline across their range, as a result of human activities. Here, we identify the most pressing issues concerning the current conservation status of Congeria and identify key priorities for its scientific study. The building of dams and other hydrotechnical constructions have led to a significant decrease in the water inputs that used to supply underground systems where Congeria lives, contributing to a reduction of the cave habitats feasible for bivalve settlement. This is relatively well documented in Popovo polje where, as a result of hydrotechnical interventions on Trebisnjica river, water level drop destroyed well over 99 % of Congeria kusceri population in Zira cave and caused their complete disappearance in other caves. Similar factors are likely to have also affected the sister species Congeria jalzici in the Lika region. In addition, the salinization of Neretva river, lack of proper wastewater management, intense agriculture, tourist exploitation, and additional hydrotechnical plans add to the ongoing decline of the quality of Congeria habitats. These threats are expected to least to drastic reductions in population size within the next few decades, and this situation might be further aggravated by the lack of regulations and active measures for Congeria protection, as well by the limited understanding of its biology. Future scientific studies should be aimed at better elucidating microhabitat preference, defining the range of tolerance of environmental parameters, and assessing the size and genetic viability of existing Congeria populations. However, we highlight that these efforts would most certainly require the collaboration of local authorities and the allocation of appropriate financial resources in order to be effective.

Background and objectives Osteoporotic vertebral compression fractures, particularly prevalent among the aging population, constitute a pressing global healthcare challenge. They often are unnoticed until severe pain and disability manifest, making them an underdiagnosed and undertreated condition. Patients who suffer from these fractures not only endure excruciating pain but also face diminished quality of life, impaired mobility, and the risk of respiratory compromise due to altered spinal alignment. The economic repercussions of vertebral compression fractures are substantial. Hospitalization costs, rehabilitation expenses, long-term care, and indirect costs related to lost productivity significantly burden healthcare systems and society at large , offering a promising avenue for enhancing patient outcomes and relieving the healthcare and societal financial strain posed by vertebral compression fractures. Kyphoplasty, a minimally invasive surgical technique, offers rapid pain relief, vertebral height restoration and improved function. Recognizing the importance of early intervention, this manuscript highlights the potential of kyphoplasty in mitigating both clinical and economic consequences. By addressing these fractures more effectively, kyphoplasty may potentially reduce long-term healthcare expenses and indirect costs. Material and Methods 66 randomized patients were divided into 2 treatment groups (kyphoplasty using single balloon and double balloon), analyzing radiographic and clinical parameters during 12 months of follow-up. Results Patients treated with double balloon obtained greater anterior and posterior vertebral height after reduction and a better local vertebral angle. Both groups of patients obtained clinical improvement after treatment (VAS and ODI), with no differences between the groups. Conclusion Patients treated with double balloon kyphoplasty had better radiographic results. This revision manuscript delves into the critical dimensions of these fractures, encompassing demographics, clinical consequences, challenges in diagnosis and management, and their profound economic impact. This manuscript serves to introduce an improved kyphoplasty technique to guide to the multifaceted nature of osteoporotic vertebral compression fractures and their management.

Introduction: Due to COVID-19 pandemic, performance of many program has been declined and Tuberculosis (TB) program is not an exception. TB case detection and notification has been recognized as one of worst hit area. The objective of this study was to explore the TB notification status of India during this pandemic and explore options to mitigate the issue. Methods: A secondary data analysis was performed on open source TB notification database of India. Relevant literature review was done to find out remedies based on the different initiative taken by different states of India. Results: In 2020, total TB notification decreased in all the states in comparison to 2019. The percentage of loss in the country was 34%. Private TB notification also decreased in 2020 in all the states except in Jharkhand. The percentage of loss in private TB notification in the country was 35%. Notification started declining in the month of February 2020 and it was lowest in the month of April-2020. The trend of notification began to improve since May 2020 when the States started taking innovative initiatives like Integrated TB Covid Case Search. Conclusion: Due to the ongoing COVID-19 pandemic the notifications of TB cases declined noticeably which has a serious implication in terms of silent spread within household and community. But the picture can be improved with integrated approach for TB-COVID case finding and management.

Unsupported sleepers or void zones in ballasted tracks are one of the most recent and frequent track failures. The void failures have the property of intensive development that, without timely maintenance measures, can cause the appearance of cost-expensive local instabilities like subgrade damages. The reason of the intensive void development lies in the mechanics of the sleeper and ballast bed interaction. The particularity of the interaction is a dynamic impact that occur due to void closure. Additionally, void zones cause inhomogeneous ballast pressure distribution between the void zone and fully supported neighbour zones. The present paper is devoted studying the mechanism of the sleeper-ballast dynamic impact in the void zone. The results of experimental in-situ measurements of rail deflections showed the significant impact accelerations in the zone even for light-weight slow vehicles. A simple 3-beam numerical model of track and rolling stock interaction has shown the similar to the experimental measurements dynamic interaction. Moreover, the model shows that the sleeper accelerations are more than 3 times higher than the corresponding wheel accelerations and the impact point appear before the wheel enters the impact point. The analysis of ballast loadings shows the specific impact behaviour in combination with the quasistatic part that is different for void and neighbour zones, which are characterised with high ballast pre-stressed conditions. The analysis of void sizes influence demonstrate that the impact loadings, wheel and sleeper maximal accelerations appear at certain void depth after which the values decrease. The ballast quasistatic loading analysis indicates more than twice increase of the ballast loading in neighbour zones for long voids and almost full quasistatic unloading for short length voids. However, the used imitation model cannot explain the nature of the dynamic impact. The mechanism of the void impact is clearly explained by the analytic solution using a simple clamped beam. A simplified analytical expression of the void impact velocity shows that it is linearly related to the wheel speed and loading. The comparison to the numerically simulated impact velocities shows a good agreement and the existence of the void depth with the maximal impact. An estimation of the long-term influences for the cases of normal sleeper loading, high ballast pre-stress and quasistatic loading in the neighbour zones and high impact inside the void are performed.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

Large Language Models (LLMs) have revolutionized the field of Artificial Intelligence with their ability to understand and generate natural language discourse. This has led to the use of LLMs in various creative fields such as music, art, and storytelling, which has sparked a debate on the impact of LLMs on human creativity. This article explores the cyclic effect of LLMs on human creativity, where LLMs can generate an ever-evolving cycle of creative output from both humans and machines. The article also highlights the importance of responsible and ethical use of LLMs, including privacy and copyright issues with the training data used by LLMs. The article emphasizes the need for transparency, data security measures, and AI governance policies to protect user data and ensure the safe use of LLMs. It also calls for the development of educational materials and resources to increase public understanding of LLMs and their ethical implications. The article concludes by highlighting the potential of LLMs as powerful tools for communication and education, but also emphasizes the need for ethical considerations to ensure the responsible and beneficial use of LLMs in society.

A crop-weed simulation model is presented to compare and evaluate Integrated Weed Management (IWM) strategies. Specifically, the model was parameterized for soybean crops in competition with Euphorbia davidii Subils. We used both, weed and crop demographic data surveyed in agronomic fields of the central zone of the Buenos Aires province, Argentina, throughout two crop cycles (2011/2012 and 2013/2014). The proposed model underwent a calibration process and subsequent validation with 70/30 % data split respectively (N=37). Two annual-based and one multiannual-based case studies were simulated to demonstrate the performance of the model. Different IWM strategies were compared under both, operational and tactical planning horizons through the evaluation of different model outcomes (i.e. crop yield, interspecific competition, economic return, and environmental impact). Our case studies results suggest that the inclusion of cultural management practices could reduce weed interspecific competition by 46 to 97 % and weed seed production by 40 to 89%. An increment in both expected crop yield, by 6 to 20%, and annual gross margin, by 44 to 199 US$.ha-1, were obtained in silico for similar levels of environmental impact.

The paper presents a conceptual model of the route of macroplastic debris (5 > mm) through a fluvial system, which can support future works on the overlooked processes of macroplastic storage and remobilization in rivers. We divided the macroplastic route into (1) input, (2) transport, (3) storage, (4) remobilization and (5) output phases. Phase 1 is mainly controlled by humans, phases 2–4 by fluvial processes, and phase 5 by both types of controls. We hypothesize that natural characteristics of fluvial systems and their modification by dam reservoirs and flood embankments construction are key controls on macroplastic storage and remobilization in rivers. The zone of macroplastic storage can be defined as a river floodplain inundated since the beginning of widespread disposal of plastic waste to the environment in the 1960s and remobilization zone as a part of the storage zone influenced by floodwaters and bank erosion. The amount of macroplastic in both zones can be estimated using data on the abundance of surface- and subsurface-stored macroplastic and the lateral and vertical extent of the zones. Our model creates the framework for estimation of how much plastic has accumulated in rivers and will be present in future riverscapes.

Impact load was applied to hardened cement paste (HCP) specimens using a gas gun to investigate microscopic changes in the specimens and develop a better response model of concrete subjected to impact load. Plasma emission was observed at the moment of impact at 420 m/s and the colour of the portion near the impact point turned brighter. This brighter portion was analysed, and it was observed that the pore structure was coarser compared to the other portion; however, the results of thermogravimetry and X-ray diffraction analysis were similar. A possible reason is that the generated heat was instantaneous and the rate of the temperature increase in the HCP decreased due to evaporation of water in the HCP. These results indicate that during impact at a few hundred m/s, porosity increase due to heat effect is more dominant than porosity decrease due to mechanical compaction.

Researchers, journals, and universities want to receive more citations for their scholarly publications. However, a paper citations depend on its quality, visibility and author’s online profile. Research support documents (unpublished papers, white papers, project reports, datasets, software, posters, online resources and teaching materials) can be additional source for increasing the author’s visibility. To enhance research visibility and impact, the full range of scholarly output should be available online on the open access platform. With open access platform, key research findings are made accessible immediately to the scientific community. Therefore, the publicly available research support documents may result in receiving more citations in addition to the published papers. In this paper we conducted a simplified three stages study on the benefits of research support documents publications on open access platform. We also elaborated on approaches of improving your research visibility and impact through these document.

The World Health Organization’s Health Economic Assessment Tool (HEAT) for walking and cycling is a user-friendly web-based tool to assess health impacts of active travel. HEAT, developed over 10 years ago, has been used by researchers, planners and policymakers alike in appraisals of walking and cycling policies of both national and more local scales. HEAT has undergone regular upgrades adopting the latest scientific evidence. This article presents the most recent upgrades of the tool. Health impacts of walking and/or cycling in a specified population are quantified in terms of premature deaths avoided (or caused). In addition to the calculation of benefits from physical activity, HEAT was recently expanded to include assessments of the burden associated with air pollution exposure and crash risks while walking or cycling. Further, impacts on carbon emissions from mode shift to active travel modes can now be assessed. Monetization of impacts using Value of Statistical Life and Social Costs of Carbon now uses country-specific values. As active travel inherently results in often substantial health benefits as well as not always negligible risks, assessments of active travel behaviour or policies are incomplete without considering health implications. The recent developments of HEAT make it easier than ever to obtain ballpark estimates of health impacts and carbon emissions related to walking and cycling.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Precision farming is transforming how antibiotics get used on farms. It fights the overuse that creates superbugs and harms nature. Farmers now have high-tech tools to use antibiotics ultra-precisely. Drones, AI, and advanced watering equipment help them pinpoint only sick plants and animals needing treatment. This shields crops while avoiding environmental damage. More careful antibiotic use makes livestock healthier and boosts harvests too. And it prevents resistant germs, where antibiotics stop working altogether. The approach helps farms in multiple ways, using fewer resources for even better results. There are some growing pains, like high costs for small farms. And questions around data privacy also cause concern. But overcoming these hurdles could help precision farming spread far and wide. This technology promises safer, greener, and more productive agriculture. Targeted use of antibiotics protects both crops and people from drug-proof germs. And nature benefits when less medicine spreads into soil and water. The future looks bright for farming with precision.

The work presents a Structural Health Monitoring (SHM) electronic system with real-time ac-quisition and processing for the determination of impact location in laminates. The novelty of this work is the quantitative evaluation of impact location errors using the Lamb wave guided mode S0, captured and processed in real-time by up to eight piezoelectric sensors. The differential time of arrival is used to minimize an error function for the position estimation. The impact energy is correlated to the amplitudes of the antisymmetric (A0 ) mode and the electronic design is de-scribed to avoid saturation for signal acquisition. The same electronic is designed to acquire symmetric (S0 ) low level signals by adequate gain, bandwidth and signal to noise ration. Such signals propagate into a 1.4mm thick aluminum laminate at the group velocity of 5150m/s with frequency frequency components above 270kHz and can be discriminated from the A0 mode to calculate accurately the differential arrival time. The results show that the error is not improved better than S0 wavelength in impact localization by using six out of eight sensors connected to the electronic system.

Shear thickening fluids (STF) are a class of fluids whose viscosity significantly rises under external loads. The research on these fluids has been advancing in recent years regarding prospective practical applications, including developing impact-absorbing composites. Following the green agendas governments and legislators advocate, this study investigates the combination of STF and other sustainable materials. Cork is a naturally occurring cellular material with a negative carbon footprint and superior energy absorption properties. With varying concentrations of STF material, cork agglomerates were formed. Notably, the analysed blends are homogeneous, contrasting with previous literary works. A series of experiments were conducted in quasi-static and dynamic conditions to determine the various mechanical responses. STF appears to influence the mechanical behaviour of cork agglomerates by providing softer deceleration rates and dispersing more energy through disaggregation mechanisms.

A high intensity Catch, Neuter, Vaccinate and Return (CNVR) intervention was used over 5 years to manage the free-roaming dog population of Greater Bangkok, using nearly 300,000 CNVR operations across cover 6 Provinces. An evaluation used multiple methods to assess the impact of this intervention, including clinic data, an observational street survey, an online attitude survey and reported cases of dog rabies confirmed with laboratory testing. The evaluation found evidence of a reduction in free-roaming dog density over time (24.7% reduction over 5 years), a reduction in dog rabies cases (average reduction of 5.7% rabies cases per month) and an improvement in dog-human relationships (a 39% increase per year in free-roaming dogs with visible signs of ownership or care, and a perception of less trouble with free-roaming dogs in districts benefiting from CNVR). The CNVR intervention appears to have been effective at managing the current free-roaming dog population and minimizing one future source of free-roaming dogs by limiting breeding of dogs accessible on the streets. However, there is evidence that other sources of free-roaming dogs exist, presumed to be predominately abandoned or lost owned dogs that were previously inaccessible to the CNVR intervention because they were ordinarily confined or living outside the project area. Hence a fully effective dog population management will require further interventions targeting owned dogs in addition to this CNVR effort.

A discharge mixing zone (DMZ) is a defined geographical area or volume of water in the receiving environment of a discharge where initial dilution of the effluent occurs and where exceedance of water quality criteria may be permitted. DMZs are essential to inform determination of discharge consent conditions and an important element of risk management frameworks to reduce any effects of the discharges on the environment and human health. In this review, we describe the principles and technical application of DMZs. We present an overview of the physical processes that govern the dispersion and dilution of wastewater discharges and the fate of contaminants in coastal environments and define key criteria for determining the size of DMZs. We summarize DMZ requirements in international legislation and guidance and exemplify their application to different types of discharges by means of case studies. The selected case studies illustrate different modelling tools for defining DMZs and different monitoring approaches to assess their effectiveness in achieving ecological and human health objectives.

Urbanization degrades natural habitats and creates new urban ecosystems, like domestic gardens. The plant composition of these gardens varies with socio-economic factors and urban planning levels. However, the diversity and impact of introduced species are often poorly assessed, causing potential ecological imbalances, particularly in Lubumbashi (DR Congo). The objective was to analyze the spatial structure, plant diversity, propagation strategies, and ecological functions of domestic gardens. Three distinct neighborhoods were selected: planned, unplanned and residential neighborhood. 20 avenues (with 5 plots per avenue) were chosen to represent the diversity within each neighborhood, and stratified random sampling of plots was conducted to analyze gardening practices. Gardens were classified into types, and their vegetation was evaluated based on species origin and ecological impact. The analysis of domestic gardens in Lubumbashi reveals significant variations across different neighborhood types. Residential neighborhoods exhibit larger average garden sizes (315.1 m²), higher species richness (22 species), and larger plot sizes (1032 m²) compared to unplanned and planned neighborhoods, where garden areas and species richness are notably lower. Rectangular gardens dominate in unplanned areas, while planned neighborhoods feature more intentional landscaping elements, such as flowerbeds and hedges. The use of gardens for food production is prominent in planned areas (40.7%), whereas residential neighborhoods prioritize ornamentation (51.4%). The study identifies 232 species across 68 families, with a predominance of exotic species (80%) in all neighborhoods, particularly in unplanned areas (82.25%). The data reveals that Mangifera indica and Persea americana are abundant in all neighborhoods, illustrating their adaptability to different urban contexts. Herbaceous species are most common, followed by woody plants, with vines being sparse. Species dispersal is primarily driven by human activities (anthropochory), accounting for over 85% in all neighborhoods. These findings highlight the strong human influence on the composition and structure of domestic gardens in Lubumbashi, emphasizing the dominance of exotic species and the importance of anthropogenic factors in shaping urban green spaces. Urban policies should incorporate strategies to minimize the negative impacts of exotic species on native flora.

This study presents a comprehensive examination of the transformative potential of Islamic finance in advancing sustainable development goals (SDGs). It underscores the unique position of Islamic finance, with its ethical and moral foundations, to contribute significantly to environmental sustainability, social equity, and economic development. The paper highlights innovative financial instruments like Zakat, Waqf, and green Sukuk, which not only align with but also actively promote SDGs. Through a multidisciplinary approach, it advocates for a paradigm shift towards integrating sustainability into the core of financial systems. The analysis includes challenges in harmonizing Human Development Indexes (HDIs) with Ecological Footprints (EFs), proposing strategies for sustainable development, ecological conservation, and educational reforms. This study is pivotal for policymakers, financial institutions, and educators, providing a roadmap for leveraging Islamic finance towards achieving a balanced, sustainable, and inclusive global economy.

Heavy metal pollution poses a significant threat to global populations, particularly impacting human health. Developing countries, characterized by chemical engineering and mining industrial activities, often contribute to diverse heavy metal contaminants. Consumption of water contaminated with heavy metals, prevalent in such regions, can lead to severe health risks, including gastric cancer. Addressing the urgent issue of heavy metal pollution, this paper employs a bibliographic approach to explore the latest literature on heavy metal pollution. The study discusses recent research findings and potential methods for the treatment and mitigation of heavy metal pollution, emphasizing the pressing need for effective solutions to safeguard public health.

The Impact Chain framework for risk assessment has proven to be a robust and effective It is very useful to set up the conceptual framework associated to a given risk and allows accommodating naturally the different components that shape that However, the operationalization of the impact chain may not be straightforward, in particular due to the inherent uncertainties associated to the selected indicators and the assigned In this paper, we introduce an extension to the Impact Chain framework that allows to consider uncertainties in the different components of the risk In the framework of the UNCHAIN project, a web-based tool has been developed to ease the task of implementing that The tool has been applied to a case study on the loss of tourist attractiveness due to heat stress conditions on the Balearic island, Spain, to illustrate how uncertainties in different components of the impact chain can affect the robustness of the final risk Also, the tool provides an estimate of the sensitivity of the final risk to each component, which can be used to guide risk mitigation Finally, a proposal for the validation of the risk assessment is presented.

In this study, we first present a time-fractional L$\hat{e}$vy diffusion equation of the exponential option pricing models of European option pricing and the risk-neutral parameter. Then, we modify a particular L$\hat{e}$vy-time fractional diffusion equation of European-style options. Introduce a more general model from the models based on the L$\hat{e}$vy-time fractional diffusion equation and review some recent findings regarding of the Europe option pricing of risk-neutral free.

Background: This research examines how market knowledge and artificial intelligence (AI) interact in different market designs such as business-to-business (B2B) settings while taking emerging technologies and the changing digitalization landscape into account. Objective: The main goal is to understand how AI affects market knowledge in different market designs such as business-to-business (B2B) contexts, taking into account language barriers, practical difficulties, and the revolutionary effects on decision-making and customer interactions. Result: They underscore the transformative potential of artificial intelligence (AI) by highlighting how it shapes market knowledge, encourages customized approaches, and improves marketing efficacy in the business-to-business (B2B) space. Conclusion: In order to create a path for responsible AI integration in B2B marketing, the study concludes with recommendations for standardized terminology related to AI, practical insights into implementation challenges, and ethical issues.

Cable-supported façades represent a novel approach in the design and technology of double skin façades (DSF). This type of systems not only offer flexibility in terms of exterior finishes, but also regulates the access of solar radiation, thereby transforming the appearance of the building in response to varying daylight conditions. However, the structural performance of these façades under wind, impact and seismic loads remains an active area of research. The study is a groundbreaking work that experimentally evaluates the wind and seismic behaviour of these type of façades. The methodology used for the evaluation of flexible masonry facades includes laboratory tests analysing the individual capacity of the connections and materials of the system under standardized and non-standardized procedures. A full-scale experimental sub-assembly specimen of a representative module of the façade is also subjected to uniformly distributed pressures of wind load tests as well as hard body and soft body impact tests. The setup considered the border conditions, tension loads, and actual materials. Furthermore, the earthquake assessment includes tests of full-scale specimens subjected to these demands. Research findings allowed the refinement and redesign of the system's components granting the validation of the DSF used as a case study.

In the face of 21st-century environmental challenges, including climate change, migration pressures, and waste disposal issues, certain healthcare sectors, notably dentistry, pose a significant global environmental footprint with concerns about carbon emissions and waste production. This scoping review delves into the paradox that healthcare, while dedicated to safeguarding health, inadvertently contributes to environmental degradation through waste accumulation and disposal. The analysis of relevant pertinent literature emphasizes the imperative for an environmentally sustainable approach to dental waste measurement, disposal methods, and comprehensive education for stakeholders. Aligned with the World Conference on Sustainable Development and the United Nations' 2030 Agenda, the study adhered to PRISMA-ScR scoping review guidelines and Institute of Medicine's recommendations. The study utilized Medline/PubMed and international organization websites for data retrieval, employing Boolean operator queries in Medline. A systematic literature analysis identified six cross-sectional studies (2004-2018) highlighting variations in dental waste composition due to the lack of standardized identification methods. This heterogeneity underscores the need for a proposed research model, emphasizing comprehensive methodologies and healthcare staff training in waste management. The study advocates for environmentally conscious dental practices, contributing to broader sustainable healthcare goals through sharing of a research protocol for dental solid waste management.

Crop digital twin is redefining traditional farming practices, offering unprecedented opportunities for real-time monitoring, predictive and simulation analysis, and optimization. This research embarks on an exploration of the synergy between precision agriculture, crop modeling, and regression algorithms to create a digital twin for augmenting farmers the concentration and composition prediction-based crop nutrient recovery. This captures the holistic representation of crop characteristics, considering the intricate relationships between environmental factors, nutrient concentrations, and crop compositions. However, the complexity arising from diverse soil and environmental conditions makes nutrient content analysis expensive and time-consuming. This paper presents the result of a predictive digital twin case study that employs six regression algorithms namely Elastic Net, Polynomial, Stepwise, Ridge, Lasso, and Linear Regression to predict rice nutrient content efficiently, particularly considering the coexistence and composition of multiple nutrients. Our research findings highlight the superiority of the Polynomial Regression model in predicting nutrient content, with a specific focus on accurate nitrogen percentage prediction. This insight can be used for nutrient recovery intervention by knowing the precise amount of nutrient to be added into the crop medium. The adoption of the Polynomial Regression model offers a valuable tool for nutrient management practices in the crop digital twin, potentially resulting in higher-quality rice production and a reduced environmental impact. The proposed method can be replicable in other low-resourced crop digital twin system.

As a rapidly growing coastal megacity, Shanghai is continuously threatened with land subsidence issues since 1920s. Land subsidence was controlled in 1960s, however in 1990s, unconscious and dangerous urban underground space (UUS) exploration and tunneling development are causing further land subsidence. It is imperative to study previous relations towards future adaptive and resilient scenario modelling and planning. There are multiple cause-effect factors determined in the urban built environment of Shanghai megacity. This paper presents the current evidence based on the relations of the multifactor of the spectrum. Methods consist of understanding the cause-effect relations and spatiotemporal from the crucial period of 1960-2020. Data are collected secondarily from multiple open sourced databases. The results determine Shanghai are highly influenced by the UUS development induced-subsidence, tunneling leakage and weak spatial modelling. Spatiotemporal pattern has shown a mixed positive-negative impact: population, land subsidence is growing in parallel distribution (positive) with tunneling leakage, construction of tunneling, metro system, UUS development, building price, reconstruction area, GDP growth, land price, arable land decrease and further tunnel settlement in Urban City Centre, Pudong New Area, Minhang, Baoshan and Songjiang districts. These results are useful for further adaptive and resilient scenario modelling and spatial planning.

In the last decades farm animals kept in confined and mechanically ventilated livestock buildings are increasingly confronted with heat stress (HS) due to global warming. These adverse conditions cause a depression of animal health and welfare and a reduction of the performance up to an increase of the mortality. To facilitate sound management decisions, livestock farmers need relevant arguments, which quantify the expected economic risk and the corresponding uncertainty. The economic risk was determined for the pig fattening sector based on the probability of HS and the calculated decrease in the gross margin. The model calculation for confined livestock buildings showed, that HS indices calculated by easily available meteorological parameters can be used for assessment quantification of indoor HS, which is so far difficult to determine. These weather-related HS indices can be applied not only for an economic risk assessment but also for a weather-index based insurance for livestock farms. Based on the temporal trend between 1981 and 2017, a simple model was derived to assess the likelihood of HS for 2020 and 2030. Due to global warming, the return period for a 90-percentile HS index is reduced from 10 years in 2020 to 3-4 years in 2030. The economic impact of HS on livestock farms was calculated by the relationship between an HS index based on the temperature-humidity index (THI) and the reduction of the gross margin. From the likelihood of the HS and this economic impact function, the probability of the economic risk could be determined. The reduction of the gross margin for a 10 year return period was determined for 1980 with 0.27 € per year and animal place and increased by the 20-fold to 5.13 € per year and animal place in 2030.

We present an updated design process for adapting and integrating existing cyber risk assessment approaches for impact assessment for the risk from IoT to the digital economy. The new design process includes a set of changes to the original standards (e.g. NIST) that are adapted for the IoT cyber risk in this paper. This paper also presents a new framework for impact assessment of IoT cyber risk, specific for the digital economy.

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging material seem to be promising due to their low weight, structure and production price. Based on the review, the linear low-density polyethylene material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a Constitutive material model to be used in future design by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of the linear low-density polyethylene under static and dynamic loading. The quasi-static measurement is realized in two perpendicular principal directions and is supplemented by a test measurement in the 45 degrees direction, i.e. exactly between the principal directions. The quasi-static stress-strain curves are analyzed as an initial step for dynamic strain rate dependent material behavior. The dynamic response is tested in the drop tower using a spherical impactor hitting the flat material multi-layered specimen at two different energy levels. The strain rate dependent material model is identified by optimizing the static material response obtained in the dynamic experiments. The material model is validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

The sustainability of cities often changes as rapid urban developments and population growth affect the carrying capacity. Understanding the dynamics of carrying capacity then becomes crucial for tourist-oriented cities. This study focused on Baguio City, the "Summer Capital of the Philippines," attracting large crowds on holidays and actively promoting various events on non-holidays, thereby having temporal context variations classified as regular days, days with events, and holidays. Using the enhanced urban carrying capacity load number (EUCCLN) model, load number (LN) changes for different temporal contexts are calculated based on spatial indicators grouped into air, traffic, economy, and waste. The city experiences the worst pressures on air quality during holidays with $99.23\%$ districts under very high to critical levels followed by regular and days with events. However, the total LN is balanced by favorable economic conditions with only $9.23\%$ at critical. EUCCLN effectively pinpoints areas experiencing critical states at any time, advocating targeted government monitoring. We demonstrate that Night Time Light, for places with no economic data available, can be used as a proxy to highlight areas requiring improved urban vibrancy. This work suggests that EUCCLN monitoring urban pressures can easily be expanded to nowcasting with real-time data.

Construction project management and cost management is a difficult process that affects the overall success of construction projects. The success of a construction project can be assessed according to key performance indicators (KPIs). Cost savings and cost optimization over the life of a construction project is one of these KPIs. Cost management is largely performed through intelligent information technology in the construction industry. Information systems and information technologies have seen an increase in use in the management of construction projects. The same goes for cost management. Several studies mentioned in the paper point to this increase in use in recent years also in the management of costs at various stages. Many studies point to the use of information technology and software applications in the field of cost management. Still, to a large extent, there are no surveys focused on the analysis of the impact and impact factor of information technology on cost savings or cost optimization in various phases of construction projects. The research discusses the issue of the impact of information technology on cost management in various phases of a construction project. The main goal of the research is to analyze the influence of information technology factors on cost savings and optimization in individual phases of a construction project. Several statistical methods were used in the research. The resulting model of information technology impact factor was created based on data processing and the use of the AHP method.

Objectives: The study aimed to uncover the percentages of battered women in Jordan, its causes, forms, and relationship to several social factors. Methodology: The study was conducted on a random, targeted sample of (1308) women based on social sample survey method and electronic questionnaire tool for data collection, the Descriptive statistical method and chi-square test were used to examine statistically significant differences. Results: The study found that the percentage of battered women reached 17.1% during Corona pandemic in 2020, and the increase in men's violence against women during this period of was in large and medium degrees according to the sample. Husbands were the most practicing violence against their wives at 37.5%, followed by fathers against daughters at 28.6%, and brothers against sisters at 26.8%. The causes of male violence are due to social factors represented by male domination culture, interference by family and relatives, and economic factors represented by the high cost of living, low household income and poverty. The most common forms of violence are verbal, physical, and psychological. The study found that women in southern Jordan, who are poorer and less educated, and who live in a large family, are the most abused. The study recommended activating family and community service and reform offices, solving problems of deteriorating economic situation and individual poverty, and enlightening community awareness of the dangers of domestic violence.

Methods to handle uncertainty in economic evaluation have gained much attention in the literature and the cost-effectiveness acceptability curve (CEAC) is the most widely used method to summarize and present uncertainty associated with program costs and effects in cost-effectiveness analysis. Some researchers have emphasized the limitations of the CEAC for informing decision and policy makers as the CEAC is insensitive to radial shifts of the joint distribution of incremental costs and effects in the North-East and South-West quadrants of the cost-effective plane (CEP). Furthermore, it has been pointed out that the CEAC does not incorporate risk-aversion in valuing uncertain costs and effects. In the present article we show that the cost-effectiveness affordability curve (CEAFC) captures both dimensions of the joint distribution of incremental costs and effects on the CEP and is therefore sensitive to radial shifts of the joint distribution on the CEP. Furthermore, the CEAFC also informs about the budget impact of a new intervention as it estimates the joint probability an intervention is both affordable and cost-effective. Moreover, we show that the cost-effectiveness risk-aversion curve (CERAC) allows to incorporate risk-aversion into the analysis and can therefore be used to inform decision-makers who are risk-averse. We use data from a published cost-effectiveness model of palbociclib in addition to letrozole versus letrozole alone for the treatment of oestrogen-receptor positive, HER-2 negative, advanced breast cancer to demonstrate the differences between CEAC, CEAFC and CERAC and show how these can jointly be used to inform decision and policy makers.

Life cycle assessment (LCA) is being included formally in EcoDesign regulations. Especially product carbon footprint will be mandatory in Europe. However, life cycle impact assessment including global warming potential (GWP) in LCA is hampered by several challenges. One of these is lack of water vapor characterization indexes for GWP. A life cycle inventory profile for air transport fuel including water vapor emissions is evaluated with state-of-the-art practice, i.e. EF Method and ILCD 2011 Midpoint+ and neglecting water vapors high altitude GWP compared to carbon dioxide. Then the characterization factor in GWP100 for water vapor and alternate normalization for particulates are introduced. The results are compared. The main findings are that the EF method and ILCD both generate rather realistic results for Particulate Matter and Respiratory Inorganics mid-point indicators, respectively, but the amount of premature deaths should be better allocated to different specific emissions, and that water vapor may dominate the GWP100 result over the usual carbon dioxide. LCIA mid-points need measurable and understandable bases. The common knowledge of water vapor’s GWP100 should not be neglected in LCIA for air transport and beyond where relevant.

The storm of November 12th-13th, 2019 provoked the displacements of boulders in a central Mediterranean rocky coast; with reference to a selected area, prone to the boulder production and geomorphologically monitored for years, a field-oriented study approach was applied for the phenomenon, by collating data concerning pre-storm locations and kinematics of these boulders. The number of displaced boulders is 11, that is, in terms of morphological imprint of a specific storm, one of the major study cases for the Mediterranean. In addition, based on widely used hydrodynamic equations, the minimum wave height required to displace the boulders is assessed. The values conform with the expected values for the wave climate dominating during the causative meteorological event and give a measure of the energy of the storm slamming the coast. Boulder dislodgements usually have plays a key role in determining the rate of the coastal recession, likely also in the investigated area. In view of an adverse climate evolution with a possible increase of energy and frequency of severe storms, the results deriving from the study of this morphodynamics should be considered for the hazard assessment and coastal management.

In this paper we present an understanding of cyber risks in the Internet of Things (IoT), we explain why it is important to understand what IoT cyber risks are and how we can use risk assessment and risk management approaches to deal with these challenges. We introduce the most effective ways of doing Risk assessment and Risk Management of IoT risk. As part of our research, we also developed methodologies to assess and manage risk in this emerging environment. This paper will take you through our research and we will explain: what we mean by the IoT; what we mean by risk and risk in the IoT; why risk assessment and risk management are important; the IoT risk management for incident response and recovery; what open questions on IoT risk assessment and risk management remain.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Energy transition is a major structural change in the whole social system, and the energy system must be changed globally to replace fossil fuels. Hydropower is one of the largest renewable energy in the world. However the involuntary resettlees due to the construction of hydropower projects are suffering from being far away from their native land, losing the land cultivated for generations and the houses they live in, and losing the social relationship network based on geography and blood ties. Based on the system evaluation theory of reservoir resettlement and referring to relevant research findings, this paper constructs a comprehensive evaluation index framework for assessing the implementation effect of the PostRelocation Support (PReS) policy. The research region is located in Zhijin County, Bijie City, Guizhou Province, China. Accordingly, a combined method of a structural equation model and a fuzzy comprehensive evaluationary model is used in this paper to analyze the implementation of the PReS policy. The results show that the total score of implementing effects of the PReS policy is 4.4, with dramatic significance. The subindex scores of the resettlers’ family income, living conditions, and production conditions; the local economy; and social stability are 4.3, 4.6, 4.4, 4.6, and 4.3, respectively, with dramatic significance. This paper has analyzed and summarized the successful practices of implementing the PReS policy for reservoir resettlers in three dimensions: poverty alleviation, beautiful home construction and accelerating rural revitalization. Research shows that China's rural reservoir resettlers' PReS policy has been more effective in restoring the livelihoods of reservoir resettlers.

Economic risks for livestock production are caused by volatile commodities and market conditions, but also by environmental drivers like increasing uncertainties due to weather anomalies and global warming. These risks impact the gross margin of farmers and can stimulated investment decisions. For confined pig and poultry production, farmers can reduce the environmental impact by implementing specific adaptation measures to reduce heat stress. A simulation model driven by meteorological data was used to calculate heat stress impact as a projection for 2030. For a business-as-usual livestock building, the indoor climate for several adaptation measures was calculated. The weather-related value-at risk quantified the economic risks caused by global warming and the stochastic component of the weather. The results show that only energy-saving adaptation measures to reduce the inlet air temperature are appropriate to reduce the economic risk to the level of the year 1980. The efficiency of other adaptation measures to reduce heat stress is distinctly lower. The results in this study can support the decision making of farmers concerning adaptation management and investments. It can inform agricultural policy design as well as technological development.

The World Health Organization estimates that every year air pollution kills seven million people worldwide. As it is expected that climate change will affect future air quality patterns, the full understanding of the links between air pollution and climate change, and how they affect human health, are challenges of future research. In this scope, a methodology to assess the air quality impacts on health was developed. The WRF-CAMx modelling framework was applied for the medium-term future climate (considering the SSP24.5 scenario) and for the recent past (considered as baseline). Following the WHO recommendations, mortality health indicators were used to estimate health impacts of long-term exposures. For that, the Aveiro Region, in Portugal, was considered as a case study. Future climate results indicate the occurrence of higher temperatures, and lower total precipitation. Despite that, improvements in the main pollutants’ concentrations, and consequently in the reduction of the related premature deaths are foreseen, mainly due to the reduction of pollutants emissions imposed by the European legislation for the upcoming years. The applied approach constitutes an added value in this research field, being crucial to anticipate the effects of climate change on air quality and evaluate their impacts on human health.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

Post-industrial recycling (PIR) and post-consumer recycling (PCR) are measures to sustain re-sources by improving materials’ circularity and sustainability. Currently, circularity is mostly measured as the degree of reutilization of a material from 0 to 100 % at product or company lev-el. This lacks in assessing the resources’ usage over multiple product life cycles. Therefore, we propose to assess circularity as (i) the frequency resources are used in products (effective circu-larity eC) and (ii) a vehicle to reduce virgin resource use and environmental impacts (environ-mentally efficient circularity eeC). Besides, to compare the environmental impacts of using recy-cled materials from PIR or PCR, we analyse their impact reduction potential (IRP) indicating the environmental benefits of recycling in relation to virgin material put onto the market. We demonstrate the suggested indicators for a case study material: polypropylene. For this polymer type, the eC ranges between 0.93 and 9.08 uses of the resource on average depending on collec-tion, sorting, and recycling rates. Likewise, the eeC ranges between 0.31 and 1.50 uses per kg of CO2 equivalents emitted. PCR has a higher IRP regarding climate change impacts than PIR in all analysed scenarios. The results reveal the relevance of PCR and PIR beyond the product life cycle.

Background: A large percentage of deaths in an epidemic or pandemic can be due to overshoot of population (herd) immunity, either from the initial peak or from planned or unplanned exit from lockdown or social distancing conditions. Objectives: We study partial unlock or reopening interaction with seasonal effects in a managed epidemic to quantify overshoot effects on small and large unlock steps and discover robust strategies for reducing overshoot. Methods: We simulate partial unlock of social distancing for epidemics over a range of replication factor, immunity duration and seasonality factor for strategies targeting immunity thresholds using overshoot optimization. Results: Seasonality change must be taken into account as one of the steps in an easing sequence, and a two step unlock, including seasonal effects, minimizes overshoot and deaths. It may cause undershoot, which causes rebounds and assists survival of the pathogen. Conclusions: Partial easing levels, even low levels for economic relief while waiting on a vaccine, have population immunity thresholds based on the reduced replication rates and may experience overshoot as well. We further find a two step strategy remains highly sensitive to variations in case ratio, replication factor, seasonality and timing. We demonstrate a three or more step strategy is more robust, and conclude that the best possible approach minimizes deaths under a range of likely actual conditions which include public response.

Agriculture and farming worldwide are responsible for numerous environmental threats, including degradation of land and water resources depletion. Underlining the dynamic interaction between bio-physical and socio-economic drivers is the key towards a more sustainable land and water management. With regard to a highly developed agricultural area in southern Italy, multi-regression models were developed to interpret the observed inter-annual variability of cropped land. Main drivers related to Common Agricultural Policy support, product market prices, crop yield and irrigation water availability were investigated. The adopted models revealed the different weighs of each driver. The findings reported the role that direct payments played in supporting the extension of irrigated crops, such as processing tomato. Likewise, the models pointed to decoupled payment scheme as the most important driver of change in the crop pattern over the last years.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

The inherited ‘EIA’ process at Brexit is based on a ‘Project’ period from Inception tothe start of construction works. The ‘Incompleteness’ of the process covers andidentifies stages that will impact on the environmental cycle: construction period,operational life, de-commissioning and a return to acceptable environmental footprint.A master environment structure-plan framework is required to commence with theupgrading of the complete ‘EIA’ process, embracing separate limbs for the UK’spriority environmental targets for climate change, and other major adverse effectswhich result in serious ‘harm’ to the UK environment. The identification of the processfor ‘incompleteness’ requires effective sustainability, and inclusion of effectivemanagement tools, for the essential ‘monitoring/control/recording’ proceduresthroughout the project life and the natural environmental cycle. This will allow theopportunity for a new approach to a structured ‘Suite of EIAR Directives’, to enable a‘EIAR’ regime that ‘will remain fit and proper for UK purpose’.

Cotton is the most ubiquitous and profitable fiber with diverse industrial and domestic applications. Grown in over 100 countries, it has a global market value of about $40 billion and employs over 350 million people from fields to textile mills, contributing about 7% of total labor-force recruitment in developing economies. Cotton has an indeterminate growth habit and an extensive tap root system affected by soil physicochemical and environmental conditions. There is a consensus among experts that conventional cotton cultivation still has a long way to attain sustainability, which is essential if cotton will maintain its competitive edge over other natural and synthetic fibers like hemp, polyesters, and rayon. Despite several efforts already committed to growing cotton sustainably, sustainability has eluded cotton cultivation globally because of the intense farm inputs (freshwater, pesticides, and heavy-duty equipment) needs, especially in developing economies. Some of the technological advancements towards achieving the goal of sustainable cotton cultivation include the development of new varieties, improved irrigation and mulching and precision agriculture techniques, application of remote sensing and Unmanned Aerial Systems (UAS) combined with image processing, and the introduction of autonomous and multi-purpose robotic platforms for growing and harvesting cotton. This review attempts to evaluate the successes already achieved by stakeholders in moving cotton towards sustainable production and identify areas where efforts are still needed to reach sustainable production and improved profitability goals for cotton with projections for future research directions.

In Nitrate Vulnerable Zones (NVZ) site-specific techniques are needed to match N availability with durum wheat (Triticum turgidum subsp. durum Desf.) requirements. Enhanced-efficiency fertilizers (EEF) can improve efficient N supply and reduce leaching, thus contributing to sustainable agriculture. To study the effects of rates, sources and timings of nitrogen application, two-year field experiments were carried out at two Mediterranean NVZs of Central Italy (Pisa and Arezzo). The trial compared: i) two N rates: one based on the crop N requirements (NO), the other on the Action Programmes’ prescriptions of the two NVZ (NAP); ii) three N sources (urea, methylene urea (MU), and nitrification inhibitor (NI) 3,4-Dimethylpyrazole phosphate (DMPP); and two top-dressing timings (1st tiller visible and 1st node detectable). Grain yield and yield components were determined, together with N uptake. Results showed that: i) grain and biomass production were reduced with NAP at both locations; ii) urea performed better than slow-release fertilizers; iii) the best application time varied depending on N source and location: at Pisa enhanced-efficiency fertilizers achieved higher yields when applied earliest, while for urea the contrary was true; at Arezzo different N fertilizers showed similar performances between the two application timings. Different behaviors of top-dressing fertilizers at the two localities could be related to the diverse patterns of temperatures and rainfall. Therefore, optimal fertilization strategies vary according to environmental conditions.

Climate change causes weather extremes to rise in frequency and severity, which could have detrimental effects on human life, property and livelihood activity. There is significant uncertainty about the influences of anthropogenic climate change on the occurrence and severity of small-scale, sudden onset weather phenomena such as hailstorms and subsequent loss and damage. Yet, several studies indicate that there is an apparent stable connection between hailstorm activity and hailstorm damage. Severe hailstorm events are observed in Bangladesh in recent years, which are, in fact, rapid-onset disasters but low exposure in terms of giving government response and media consideration. Hence this study examines potential impacts and management strategies for loss and damage resulting from hailstorm events among smallholder farmers in Kurigram District's Phulbari Upazila of Bangladesh. Firstly, the direct and long term economic and non-economic loss and damage caused by the hailstorm on human well-beings and livelihoods were assessed. Then, the study evaluated the current adaptation, coping, management and response strategies at the institutional and community level in the context of such extreme events. Finally, a regulatory framework and implementation approaches had suggested achieving the country's resilience against disaster and climate change-induced loss and damage. Participatory Vulnerability Analysis, Key Informant Interviews and Sample Surveys accumulated the primary data for the study. In addition, secondary data were collected through analysis of literature, published and unpublished scientific articles and media reports, etc. This research outcome will help countries develop a guideline to address climate change and disaster-related loss and damage.

The electronic cigarette or e-cigarette is the new alternative method to deliver nicotine. In 2007, the United States introduced vaping devices on the market. Due to their attractive taste and lack of adverse effects, these vaping devices have gained popularity among youth and adults. However, there has been increasing evidence that vaping can cause severe lung injury, and these devices release toxic chemicals into the body. E-cigarettes are recognized as a global threat to public health. Nicotine, the most prevalent chemical in vaping devices, is associated with neurological problems and cognitive decline. Long-term use of e-cigarettes can cause adverse health problems, including respiratory illnesses, asthma, bronchitis, and lung inflammation. In 2019, the Centers for Disease Control and Prevention (CDC) officially declared vaping-associated illness EVALI (e-cigarette or Vaping Product Associated Lung Injury). The US Surgeon General published an alarm in December 2016 that e-cigarette consumption among adolescents and teens in the US is a "major public health concern" and that more young people are now vaping than smoking traditional cigarettes and cigars. Since its commercial introduction in 2003, modern electronic cigarettes (or E-cigarette s) have become increasingly popular with smokers, non-smokers, and those who used to smoke who have switched to them. With such a rise in consumption, people are becoming more aware of the irritating, harmful, and perhaps cancer-causing effects on the lungs. (Chadi et al., 2019; Dinardo & Rome, 2019; Lyzwinski et al., 2022; Marrocco et al., 2022; O’Callaghan et al., 2022)

In the era of digital information consumption, YouTube has emerged as a prominent platform for disseminating knowledge across various domains. One such area that has gathered significant attention is teeth whitening, with a plethora of videos offering insights into professional proce-dures, home remedies, and personal experiences. This study delves into the vast landscape of teeth whitening content on YouTube, meticulously categorizing videos into professional and amateur domains. The aim is to critically analyze the information presented, considering its accuracy, re-liability, and potential impact on public perceptions and oral health choices. A total of 100 videos in Greek (n1= 73) and in English (n2= 27) were studied. The analysis was based on views, likes, publication year, duration, presence of background music, and the presence of a description. The completion date of the search was October 7, 2023. Professional videos predominantly present whitening as a painless, conservative, and economical procedure, emphasizing safety measures. Bleaching mechanisms involving hydrogen peroxide and carbamide are explored, with various application techniques discussed, including whitening strips, splints, and in-office procedures. Contradictory findings on the efficacy of home versus in-office treatments are highlighted. In-ternal and external discoloration factors are delineated, with contraindications specified. Amateur videos, garnering greater public appeal, present personal experiences, product promotions, and homemade remedies, reflecting a concerning trend of misinformation. The analysis incorporates viewer engagement metrics, emphasizing the impact of non-professional content. As social media platforms play an increasingly influential role in shaping healthcare narratives, understanding the nuances of dental discourse on YouTube becomes crucial for both practitioners and the public. This exploration encompasses a spectrum of topics, ranging from the chemical intricacies of bleaching agents to the societal dynamics influencing viewer preferences. By unraveling the complexities of online dental information, this study seeks to contribute valuable insights to the evolving land-scape of oral health education in the digital age. Future research should adopt a multi-platform approach and explore the dynamic interaction between content creators and viewers for a more holistic comprehension of online dental information.

The metaverse, a virtual world comprising a collective virtual shared space where users interact with one another through avatars and computer-generated objects, aims to closely mimic our real world by integrating elements of Artificial Intelligence (AI), immersive reality, advanced connectivity, and Web3. As metaverse technologies gain momentum across multiple sectors, including animal farming, their potential for addressing complex challenges such as climate change and sustainability in precision food production systems becomes increasingly apparent. However, it is crucial to consider the ethical implications and the role of sensor data and livestock behavior analysis in developing metaverse technologies for modern animal farming, given the sensitive and controversial nature of animal welfare. Failure to address these ethical considerations and harness the power of sensor data and behavior analysis could lead to a lack of credibility and insensitivity towards adopting metaverse technologies in the animal farming sector. It is essential to ensure that the development of metaverse technologies does not prioritize technology over animal welfare, ethics, socio-economic implications, and the potential for data-driven insights. Addressing diversity and equity in the context of animal farming and the metaverse is crucial to avoid perpetuating existing inequalities during the implementation of metaverse technologies. This groundbreaking paper ventures into unexplored territory, shedding light on the untapped potential of the metaverse for modern animal farming. While research on this topic is still in its infancy, we embark on a journey of visionary speculation, presenting a compelling technology forecast that envisions the extraordinary possibilities awaiting us in the future. By delving into the metaverse's transformative capabilities, we provide a glimpse into a world where animal farming transcends its traditional limitations and embraces a new era of efficiency, sustainability, and ethical practices.

African swine fever (ASF) is a notifiable viral disease of domestic and wild suids. Despite intensive re-search efforts, the pathogenesis of the disease is still far from being understood. Analysis of biomarkers in different body fluids may supplement traditional pathogenesis studies. As reliable protocols are often es-tablished in laboratories with lower biosafety, reliable inactivation of samples is crucial. The objective of this study was to find a procedure that inactivates the virus while preserving the biomarkers for down-stream analyses. To this means, three different inactivation protocols were employed, namely Tergitol-type NP-40 (NP-40) and polyoxyethylene-p-t-octylphenol (Triton X-100), respectively, and one with 95 °C heating. It could be demonstrated that all samples treated with 0.5% (v/v) concentration of both deter-gents showed absence of virus infectivity. The same was true for heated samples. However, heated serum was not suitable for analyses. Next, the treatment impact on biomarker readouts was assessed. While all protocols had an impact on the detection of biomarkers, correlation was retained. Especially NP-40 could be the desired detergent for more accurate measurements while achieving efficient virus inactivation. Based on these studies, samples can be reliably inactivated for most biomarker analyses and thus broader interdisciplinary cooperation is possible.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Several factors impact the durability of concrete bridge decks, including traffic loads, fatigue, temperature changes, environmental stress, and maintenance activities. Detecting problems such as corrosion, delamination, or concrete degradation early on can lower maintenance costs. Nondestructive evaluation (NDE) techniques can detect these issues at early stages. Each NDE method, meanwhile, has limitations that reduce the accuracy of the assessment. In this study, multiple NDE technologies were combined with machine learning algorithms to improve the interpretation of half-cell potential (HCP) and electrical resistivity (ER) measurements. A parametric study was performed to analyze the influence of five parameters on HCP and ER measurements, such as degree of saturation, corrosion length, delamination depth, concrete cover, and moisture condition of delamination. The results were obtained through finite element simulations and used to build two machine learning algorithms, a classification algorithm and a regression algorithm, based on the Random Forest methodology. The algorithms were tested using data collected from a bridge deck in the BEAST® facility. Both machine learning algorithms were effective in improving the interpretation of ER and HCP measurements using data from multiple NDE technologies.

The A.C.Q.U.A. (Advisable Conscious Quality Use from Assisi) project, promoted by the Climate and Energy and Heritage Design courses of the Planet Life Design Master Program, addresses the theme of the recovery and regeneration of ancient wash-houses in the context of energy, environmental sustainability and innovation, a way of understanding cultural heritage in the wider sense of heritage community through the active participation of all the actors involved: universities, institutions, businesses, students and citizens. The proposal, tested in the municipalities of Assisi and Ruviano (ITALY), involves the creation of a "Community Wash House", a new way of carrying out the usual domestic act of washing clothes in the open air, next to the places where this rite was traditionally performed, in technologically innovative constructions that use renewable energy sources and encourage a reduction in household consumption of water and energy. This project is part of the training of professionals in the new inter-university course that combines knowledge of the tools of technical and scientific design with historical and cultural perspectives in a perspective of sustainable redevelopment of existing structures in the area and the use of alternative energy sources with low climate impact, calculated using the statistics of the Copernicus CDS.

Important first phases in the process of implementing CO2 subsurface and ocean storage projects include selecting of best possible location(s) for CO2 storage, site selection evaluation. Sites must fulfil a number of criteria that boil down to the following basics: they must be able to accept the desired volume of CO2 at the rate at which it is supplied from the CO2 source(s); they must as well be safe and reliable; and must comply with regulatory and other societal requirements. They also must have at least public acceptance and be based on sound financial analysis. Site geology; hydrogeological, pressure, and geothermal regimes; land features; location, climate, and access, etc. can all be refined from these basic criteria. In addition to aiding in site selection, site characterization is essential for other purposes, such as foreseeing the fate and impacts of the injected CO2, and informing subsequent phases of site development, including design, permitting, operation, monitoring, and eventual abandonment. According to data from the IEA, in 2022, emissions from Africa and Asia's emerging markets and developing economies, excluding China's, increased by 4.2%, which is equivalent to 206 million tonnes of CO2 and were higher than those from developed economies. Coal-fired power generation was responsible for more than half of the rise in emissions that were recorded in the region. The difficulty of achieving sustainable socio-economic progress in the developing countries is entwined with the work of reducing CO2 emissions, which is a demanding project for the economy. Organisations from developing countries, such as Bangladesh, Cameroon, India, and Nigeria, have formed partnerships with organisations in other countries for lessons learn and investment within the climate change arena. The basaltic rocks, coal seams, depleted oil and gas reservoirs, soils, deep saline aquifers, and sedimentary basins that developing countries (Bangladesh, Cameroon, India, and Nigeria etc) possesses all contribute to the individual country's significant geological sequestration potential. There are limited or no carbon capture and storage or clean development mechanism projects running in these countries at this time. The site selection and characterization procedure are not complete without an estimate of the storage capacity of a storage location. Estimating storage capacity relies on volumetric estimates because a site must accept the planned volume of CO2 during the active injection period. As more and more applications make use of site characterization, so too does the body of written material on the topic. As the science of CO2 storage develops, regulatory requirements are implemented, field experience grows, and the economics of CO2 capture and storage improve, so too will site selection and characterisation change.

We report recent enhancements of the online atomic database at the Ohio State University, NORAD-Atomic-Data, that provides various parameters for radiative and collisional atomic processes dominant in astrophysical plasma. NORAD stands for Nahar Osu RADiative. The database belongs to the data sources, especially for the latest works, of the international collaborations of the Opacity Project and the Iron Project. The contents of the database are calculated values for energies, oscillator strengths, radiative decay rates, lifetimes, cross sections for photoionization, electron-ion recombination cross sections and recombination rate coefficients. We have recently expanded NORAD-Atomic-Data with several enhancements over those reported earlier. They are as follows. i) We continue to add energy levels, transition parameters, cross sections for atoms and ions with their publications. ii) Recently added radiative atomic data contains significant amount of transition data for photo-absorption spectral features corresponding to x-ray resonance fluorescence effect, prominent wavelength regions of bio-signature elements, such as phosphorus ions, and emission bumps of heavy elements, such as of lanthanides, that may be created in a kilonova event. We are including iii) collisional data for electron-impact-excitation, iv) experimental data for energies and oscillator strengths for line formation, v) experimental cross sections for photoionization that can be applied for benchmarking and other applications, and vi) introduction of a web-based interactive feature to calculate spectral line ratios at various plasma temperature and density diagnostics, starting with our recently published data for P II. We presented summary description of theoretical backgrounds for the computed data in the earlier paper. With introduction of experimental results, we present summary description of measurement of high resolution photoionization cross sections at Advanced Light Source of LBNL synchrotron set-up and briefly discuss other set-ups. These additions should make NORAD-Atomic-Data more versatile for various applications. For brevity, we provide information on the extensions and avoid repetition of data description of the original paper.

Historical analysis of Australian bushfire data spanning 170 years addresses whether the strength of recent fire events has been exacerbated by human-induced climate change. The question of “cause” looks at the characteristics of a wider range of natural hazards. Fire characteristics are compared with earthquake hazard characteristics: (1) energy – termed “magnitude”; (2) severity – termed “intensity”; and (3) resultant damage to people and structures – termed “impact”.Published global, Northern and Southern hemisphere temperature data are shown to vary consistently in phase over 170 years, but vary in amplitude with statistical significance. CO₂ levels north and south of the Equator have tracked quite consistently. Thus, Southern Hemisphere bushfire magnitude and intensity is compared with the Southern Hemisphere climate record, rather than a global data set.28 major bushfires and associated droughts since 1850 show neither apparent drought extent, nor area burned, nor bushfire intensity, correlates with changes in Southern Hemisphere climate. Average rainfall from 1900 shows a wetter, rather than drier trend. Cyclone energy shows no significant trend with climate. Planet-wide “greening”, through CO₂ fertilisation, is an insignificant contributor to bushfire magnitude. Combustion theory shows recorded “global warming” could have had no significant influence on bushfire magnitude or intensity. Any increase in Australian bushfire impact, as judged by lives lost, similarly, shows no correlation with bushfire magnitude, nor indeed, any observed Southern Hemisphere global warming.Thus, bushfire magnitude seems much more likely driven by fuel load and any anomalous bushfire intensity is likely driven by anomalous ground level fuel load. The evidence suggests that any CO₂ emissions reduction will have no impact on future bushfire “severity.

Into the frame of the French TANDEM project (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modelling) Principia has been working on the development and qualification of two in-house CFD software’s: the 2D EOLE-SV (Saint Venant) model for simulation of large scale tsunami propagation from the source up to coastal scale and the 3D EOLE-NS (Navier-Stokes) model dedicated to tsunami coastal impact modelling. This paper presents a large range of test cases carried out into the frame of the project and dedicated to the validation of numerical codes in various tsunami wave conditions. The main aspects of phenomena such as wave generation, propagation and coastal impact are investigated on academic situations. A real case simulation is concerned as well, the devastating 2011 Tohoku event which is compared with in-situ data.

As the increase threat of flood risk and environmental safety due to the urbanization, Sponge city research has been attracting extensive attention both in practical and theoretical research field. To date, there are only scattered studies about Sponge city. Moreover, vary names of Sponge city prevalent in different countries, which leads to disconnection of literature in the same field of Sponge city. In this paper, a thorough systematic literature mining of Sponge city is presented. A literature analysis system is created, which includes literature export from Web of Sciences and systematic analysis via NoteExpress and CiteSpace. Some literature statistical results are derived. Challenges and opportunities for future research are anticipated. Our goals are to promote this promising thought, summarize past research, and identify issues for future research to create impacts on the practice of Sponge city.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.

Posttraumatic stress disorder (PTSD) and/or specific PTSD symptoms may evoke disordered eating and unhealthy lifestyles, resulting in adverse cardiometabolic events (e.g., hypertension and obesity) in certain groups, which may implicate the treatment of this complex condition. The diagnostic criteria of PTSD have lately expanded beyond the three common symptoms (intrusion, avoidance, and hyperarousal). Simultaneously, four-, five-, and six-dimensional structures of the Impact of Event Scale-Revised (IES-R), a popular PTSD measure, seem to be more robust than the original three-dimension structure. Within the context of COVID-19, this instrumental study used a convenience sample of 58 dental healthcare workers (HCWs) from Russia (mean age = 44.1±12.2 years, 82.8% females) to examine the criterion and predictive validity of two IES-R structures: the IES-R3 and the IES-R6 (with the added symptoms of numbing, sleep disturbance, and irritability). The subscales of the two IES-R structures expressed good internal consistency, strong correlations with the PTSD Symptom Scale (PSS), hypertension diagnosis, and high body mass index (BMI). In receiver-operating characteristic (ROC) curve analysis, all IES-R models perfectly predicted the PSS (all area under the curve (AUC) >0.9, p values <0.001). The IES-R, both hyperarousal subscales, and the IES-R3 intrusion subscale significantly predicted high BMI. Both avoidance subscales and the IES-R3 intrusion subscale, not the IES-R, significantly predicted hypertension. In conclusion, both IES-R structures can reliably measure PTSD symptoms. The IES-R, hyperarousal, and intrusion may be credible criterion variables for predicting high BMI within PTSD while the intrusion and avoidance subscales may reflect the cardiovascular consequences associated with PTSD more reliably than the IES-R itself. The IES-R subscales may predict cardiometabolic adversities in PTSD, signifying a need for proper assessment of lifestyle and the application of dietary and exercise interventions in order to lower physical morbidity in PTSD. Replicating the study in larger samples, which comprise different physical and mental conditions from heterogenous cultural contexts is pivotal to validate the results (e.g., in specific groups such as those with confirmed traumatic exposure and comorbid mood dysfunction).

Textile and clothing is one of the most important industrial sectors, not only due to the significant number of jobs generated, but also because it addresses one of the people’s fundamental needs (clothing). It is, however, a sector with a huge environmental impact, all over the world, and also an important social impact, especially in developing countries. Sustainability in the Textile &amp; Clothing value chain is a known issue, concerning both environmental, and economical-social facets of sustainability. One way to improve sustainability in this sector is by measuring the environmental, economic and social impacts of value chain activities and, ultimately, computing an Environmental and Circular score for each batch of textile and clothing product, and an Economical and Social score for each involved firm, reflected in their products. The consumer will then have the opportunity and responsibility for selecting products with the least negative environmental, economical and social impact. This article presents the results of STVgoDigital project - PPS1, developed in Portugal with the aim of implementing the traceability of textile and clothing products, boosting sustainability in this sector, and preparing the ground for the implementation of the circular economy. More exactly, a blockchain-based textile and clothing value-chain traceability platform is presented, for tracing textile product lots and activities, along the value chain, classifying them with a score, which measures their environmental and social impact. The environmental, economic and social impact scores are based on a set of proposed indicators. The results are assessed through the presentation of a case study of a face towel (home textile) and a case study of a T-shirt (clothing).

The goal of this paper is to contribute the perspective of a systems engineer to the effort to fight pandemics. The availability of low latency case data and effectiveness of social distancing suggest there is sufficient control for successful smoothing and targeting almost any desired level of low or high cases and immunity. This control proceeds from spontaneous public reaction to caseloads and news as well as government mediated recommendations and orders. We simulate multi-step and intermittent-with-feedback partial unlock of social distancing for rapidly-spreading moderate-mortality epidemics and pandemics similar to COVID-19. Optimized scenarios reduce total cases and therefore deaths typically 8% and up to 30% by controlling overshoot as groups cross the herd immunity threshold, or lower thresholds to manage medical resources and provide economic relief. We analyze overshoot and provide guidance on how to damp it. However, we find overshoot damping, whether from expert planning or natural public self-isolation, increases the likelihood of transition to an endemic disease. An SIR model is used to evaluate scenarios that are intended to function over a wide variety of parameters. The end result is not a case trajectory prediction, but a prediction of which strategies produce near-optimal results over a wide range of epidemiological and social parameters. Overshoot damping perversely increases the chance a pathogen will transition to an endemic disease, so we briefly describe the undershoot conditions that promote transition to endemic status.

In Data Science we are concerned with the integration of relevant sciences in observed and empirical contexts. This results in the unification of analytical methodologies, and of observed and empirical data contexts. Given the dynamic nature of convergence, described are the origins and many evolutions of the Data Science theme. The following are covered in this article: the rapidly growing post-graduate university course provisioning for Data Science; a preliminary study of employability requirements, and how past eminent work in the social sciences and other areas, certainly mathematics, can be of immediate and direct relevance and benefit for innovative methodology, and for facing and addressing the ethical aspect of Big Data analytics, relating to data aggregation and scale effects. Associated also with Data Science is how direct and indirect outcomes and consequences of Data Science include decision support and policy making, and both qualitative as well as quantitative outcomes. For such reasons, the importance is noted of how Data Science builds collaboratively on other domains, potentially with innovative methodologies and practice. Further sections point towards some of the most major current research issues.

We consider an alternative hypothesis of crater formation -- through an electric discharge machining (EDM) of the celestial bodies' surfaces. The source of the energy and the current itself may lie in the plasma infalling on a celestial body (from an extremely strong solar outburst or a nearby supernova). This mechanism may have been even more important than impact cratering in the early Solar System, with potential implications to the history of the dynamics of the System itself and solar activity in particular. In this light, the conclusion that shocked and metamorphosed minerals found within crater sites are evidence of hypervelocity impacts might be reconsidered. There are ambiguities that remain among sources of mineralogical formations. This study is ongoing with details of investigations supporting a new approach to crater formation not yet exhausted. Apart from mineralogical analysis and theoretical considerations regarding the large scale crater formation, we present a description of experimental studies of EDM acting at low pressures. Experimental results are made with crude setups and could easily be replicated on a larger scale with valuable research potential, as there is a well understood relation between the crater size and the energy needed for its production.

Background: This study addresses the burgeoning impact of Large Language Models (LLMs) such as ChatGPT on the integrity of online examinations and seeks to demonstrate latent and advanced LLM reasoning capabilities. The research devises an iterative self-reflective strategy for invoking critical thinking and higher-order reasoning in LLMs based on multimodal exam questions using visuals and text. Methods: The proposed strategy was demonstrated and evaluated on real exam questions by subject experts and the performance of ChatGPT (GPT-4) with vision was estimated on an additional dataset of 600 text descriptions of multimodal exam questions, focusing on its response to complex, visual, and textual prompts. Results: The results indicate that latent multi-hop reasoning capabilities can be invoked using the proposed self-reflective strategy, which can effectively steer ChatGPT towards correct answers by integrating critical thinking from each modality into the final response. Meanwhile, ChatGPT demonstrated considerable proficiency in being able to answer multimodal exam questions across 12 subjects. Conclusions: This work challenges findings from recent studies which claim that existing LLMs are unable to reason on complex multimodal tasks, and therefore this study underscores the need for enhanced online exam security measures like proctoring software, that can mitigate the potential misuse of AI technologies in educational settings.

Many studies of hypervelocity impact craters have described the characteristics of quartz grains shock-metamorphosed at high pressures of > 10 GPa. In contrast, few studies have investigated shock metamorphism at lower shock pressures. In this study, we test the hypothesis that low-pressure shock metamorphism occurs in near-surface nuclear airbursts and that this process shares essential characteristics with crater-forming impact events. To investigate low-grade shock microstructures, we compared quartz grains from Meteor Crater, a 1.2-km-wide impact crater, to those from near-surface nuclear airbursts at the Alamogordo Bombing Range, New Mexico in 1945 and Kazakhstan in 1949/1953. This investigation utilized a comprehensive analytical suite of high-resolution techniques, including transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD). Meteor Crater and the nuclear test sites all exhibit quartz grains with closely-spaced, sub-micron-wide fractures that appear to have formed at low shock pressures. Significantly, these micro-fractures are closely associated with Dauphiné twins and are filled with amorphous silica (glass), widely considered a classic indicator of shock metamorphism. Thus, this study confirms that glass-filled shock fractures in quartz form during near-surface nuclear airbursts, as well as crater-forming impact events, and by extension, it suggests that they may form in any near-surface cosmic airbursts in which the shockwave is coupled to Earth’s surface. The robust characterization of such events is crucial because of their potential catastrophic effects on the Earth’s environmental and biotic systems.

Many studies of hypervelocity impact craters have described the characteristics of quartz grains shock-metamorphosed at high pressures of >10 GPa, but in contrast, few studies have investigated shock metamorphism at lower shock pressures. In this study, we test the hypothesis that low-pressure shock metamorphism occurs in near-surface nuclear airbursts and that this process shares important characteristics with impact-cratering events. To investigate low-grade shock microstructures, we compared quartz grains from Meteor Crater, a 1.2-km-wide impact crater, to those from near-surface nuclear airbursts at the Alamogordo Bombing Range, New Mexico in 1945 and Kazakhstan in 1949/1953. This investigation utilized a comprehensive analytical suite of high-resolution techniques, including transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD). Meteor Crater and the nuclear test sites all exhibit metamorphosed quartz grains with closely-spaced, sub-micron-wide fractures that appear to have formed at low shock pressures. Importantly, these micro-fractures are closely associated with Dauphiné twins and are filled with amorphous silica (glass), widely considered to be a classic indicator of shock metamorphism. Thus, this study confirms that glass-filled shock fractures in quartz form during near-surface nuclear airbursts, as well as crater-forming impact events, and by extension, it suggests they also may form in near-surface cosmic airbursts.

The Impact of Event Scale-Revised (IES-R) is the most popular measure of post-traumatic stress disorder (PTSD), which has been recently validated in Arabic. This instrumental study aimed to determine optimal cutoff scores of the IES-R and its subscales in Arab samples of psychiatric patients (N = 168, 70.8% females) and healthy adults (N = 992, 62.7% females) from Saudi Arabia during the COVID-19 pandemic as an ongoing collective traumatic event. Based on a cutoff score of 14 of the Depression Anxiety Stress Scale 8-items (DASS-8), receiver operator curve (ROC) analysis revealed two optimal points of 39.5 and 30.5 for the IES-R in the samples (area under the curve (AUC) = 0.86 &amp; 0.91, p values = 0.001, 95% CI: 0.80-0.92 &amp; 0.87 to 0.94, sensitivity = 0.85 &amp; 0.87, specificity = 0.73 &amp; 0.83, Youden index = 0.58 &amp; 0.70, respectively). Different cutoffs were detected for the six subscales of the IES-R, with numbing and avoidance expressing the lowest predictivity for distress. Meanwhile, hyperarousal followed by the irritability expressed stronger predictive capacity for distress than all subscales in both samples. In path analysis, pandemic-related irritability resulted from direct and indirect effects of key PTSD symptoms (intrusion, hyperarousal, and numbing). Irritability contributed to traumatic symptoms of sleep disturbance in both samples while the opposite was not true. The findings suggest usefulness of the IES-R at a score of 30.5 for detecting adults prone to trauma related distress, with higher scores needed for screening in psychiatric patients. Various PTSD symptoms may induce dysphoric mood, which represents a considerable burden that may induce circadian misalignment and more noxious psychiatric problems/ co-morbidities (sleep disturbance) in both healthy and diseased groups.

Many academics are critical of the current publishing system, but it is difficult to create a better alternative. This review relates to the Sciences and Social Sciences, and discusses the primary purpose of academic journals as providing a seal of approval for perceived quality, impact, significance, and importance. The key issues considered include the role of anonymous refereeing, continuous rather than discrete frequency of publications, avoidance of time wasting, and seeking adventure. Here we give recommendations about the organization of journal articles, the roles of associate editors and referees, measuring the time frame for refereeing submitted articles in days and weeks rather than months and years, encouraging open access internet publishing, emphasizing the continuity of publishing online, academic publishing as a continuous dynamic process, and how to improve research after publication. Citations and functions thereof, such as the journal impact factor and h-index, are the benchmark for evaluating the importance and impact of academic journals and published articles. Even in the very top journals, a high proportion of published articles are never cited, not even by the authors themselves. Top journal publications do not guarantee that published articles will make significant contributions, or that they will ever be highly cited. The COVID-19 world should encourage academics worldwide not only to rethink academic teaching, but also to re-evaluate key issues associated with academic journal publishing in the future.

A multitude of factors influence our well-being and health in everyday life. Some of which we are totally aware like a delayed train, car exhausts, or continuous work stress. Other factors influence us on a subconscious level, making them, however, not less important to address. One of these factors is the built environment surrounding us almost every second of our lives. The idea of biophilic design states the importance of natural elements implemented in architectural structures to improve the occupants’ health and well-being. Adding to this field of research, this article targets the impact of biophilic design on positive emotions and productivity by using novel approaches like Facial Emotion Recognition (FER) with Residual Masking Networks, and sentiment detection using Large Language Models. Two separate but related studies were conducted and their results reported here. The first study measured emotions of people when confronted with images of different kinds of architecture, via FER (Facial Emotion Recognition) and also via a user survey. We distinguish between self-stated emotions entered through a survey by study participants, and emotions detected from studying the participants’ faces through AI from our FER (Facial Emotion Recognition) system. We found clear trends for most detected emotions, and significant evidence for self-stated emotions, that architecture implementing biophilic design evokes more positive emotions than one that does not. The second study measures the influence of natural elements on productivity and team-engagement. We found that natural elements do influence productivity and sentiment positively; however, only the change in sentiment was shown to be significant. As our sample size, especially for the second study, was relatively small, future research will apply these ideas in a larger setup to acquire further evidence for the importance of biophilic design for human well-being and health.

Perhaps the greatest challenge in the graft copolymerization of acrylic acid onto starch initiated by Fenton’s is the selectivity of the grafting reaction. Low selectivity means that too much of unwanted homopolymer polyacrylic acid is produced. In this paper, it has been analyzed why with this reaction system, involving a water soluble monomer and indirect initiation, the graft selectivity is such a challenge. Several other grafting reactions, especially with monomers of low water solubility or when direct initiation is applied, show a better grafting performance. A scheme is presented based on reaction engineering principles, that supports an explanation of the observed differences. A more selective activation of starch is a factor, but perhaps even more important is a low monomer to starch ratio at the starting sites of graft reactions. Based on these insights, several methods to improve the graft selectivity are evaluated, with the help of literature data but mostly by experimental explorations in our laboratory. Most promising appears to be a dedicated dosage method, to add monomer in portions over time, tested in a batch reactor with gelatinized cassava starch. This way, both grafting percentage and graft selectivity could be improved. Such could not be realized with the more conventional dosage, which is to add all monomer before the start of the reaction. This can be considered a principal breaktrough. Still, more research and development would be needed to refine the method and to implement the idea also in a continuous reactor at larger scale.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.