If a lubricant contains structures capable of conducting energy, reactions involving zinc dialkyldithiophosphate (ZDDP) may take place both very close to and away from the solid surfaces, with this indicating that ZDDP can be a highly effective anti-wear (AW) additive. The central thesis of this article is that the tribocatalytic effect is observed only when the energy emitted by the solids is transmitted by ordered molecular structures present in the lubricant, e.g., graphene. The friction tests were carried out for 100Cr6 steel balls in a sliding contact with uncoated or a:C-H-coated HS6-5-2C steel discs in the presence of polyalphaolefin 8 (PAO 8) as the lubricant, which was enhanced with graphene and/or ZDDP. There is sufficient evidence of the interactions occurring between ZDDP and graphene and their effects on the tribological performance of the system. It was also found that the higher the concentration of zinc in the wear area, the lower the wear. This was probably due to the energy transfer resulting from the catalytic decomposition of ZDDP molecules. Graphene, playing the role of the catalyst, contributed to that energy transfer.

Laser powder bed fusion (L-PBF) is a type of additive manufacturing technology that processes metal powders into a component. Support structures are an essential part of the L- PBF process as they transfer the laser-induced heat during and shortly after the process to the substrate, sustaining positional accuracy of downward facing surfaces of the component. Since the use of support structures is inevitable, optimized designs for them are crucial in realizing more sustainable production process. In a serial production setup, reducing the lead time and cost of a non-value-added process step like support structure removal is of significance when improving the overall business case and competitiveness.The goal of this study was to verify the applicability of lattice-based support structures for L-PBF. To achieve this, different lattice types as support structures were designed. They were tested, compared and verified for a Siemens gas turbine component. The results showed that the generated lattice-based support structures could be suitable for L-PBF. The supports had to be designed appropriately such that they could preserve the geometry of the part. Furthermore, they had to have a short fabrication time and to be removable easily, preferably without machining or sawing.

The development of high complexity geometry parts is one of the main goals of the additive manufacturing technology. However, the failure of printed structures and the joining of different parts to create complex assemblies represents a real challenge in the research of efficient and sustainability techniques for the permanent assembly of polymers. Laser welding processes have been used as a single step method to join metals until years ago. Nowadays, the growing trend in the use of thermoplastics for additive manufacturing has led to the need to adapt this technique to materials with a very specific nature and more sensitive to thermal effects. Also, the possibility of transmitting the laser beam through transparent polymer layers allows to focus the energy supply on internal sections of the assembled components. In this research, an infrared laser marking system was used to join two different samples of polylactic acid manufactured by fused deposited modeling technology. In order to increase the effectiveness of the bonding process, a transparent and a dark sample have been used as assembly material, focusing the laser beam on the interface area of the two parts. By means of tensile tests, dimensional measurement and the use of optical microscopy techniques, a basis was established that links the supplied energy by laser to the joining performance.

Successive-addition-of-digits-of-a-number(SADN) refers to the process of adding up the digits of an integer number until a single digit is obtained. Concept of SADN has been occasionally identified but seldom employed in extensive mathematical applications. This paper discusses SADN and its properties in terms of addition, subtraction and multiplication. Further, the paper applies the multiplication-property of SADN to understand the distribution of prime numbers. For this purpose the paper introduces three series of numbers -S1, S3 and S5 series- into which all odd numbers can be placed, depending on their SADN and the rationale of such classification. Extending the analysis the paper explains how composite numbers of the S1 and S5 series can be derived. Based on this discussion it concludes that even as the concept of SADN is rather simple in its formulation and appears as an obvious truism but a profound analysis of the properties of SADN in terms of fundamental mathematical functions reveals that SADN holds a noteworthy position in number theory and may have significant implications for unfolding complex mathematical questions like understanding the distribution of prime numbers and Goldbach-problem.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 ml min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of colored beers, soft drinks and candies.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

Bone is a dynamic tissue with the capacity of repair and regeneration in specific conditions. Nevertheless, due to the increased incidence of bone disorders, the need of bone grafts has been growing over the past decades and the development of an ideal bone graft with optimal properties remains a clinical challenge. This review addresses the bone properties (morphology, composition and their repair and regeneration capacity) and puts the main focus on the potential strategies for developing bone repair and regeneration materials. It describes the requirements for designing a suitable scaffold material, types of materials (polymers, ceramics and composites) and techniques to obtain the porous structures (additive manufacturing techniques/robocasting or derived from marine skeletons) for bone tissue engineering applications. The main objective of this review is to gather the knowledge on the materials and methods for the production of scaffolds for bone tissue engineering and highlighting the potential of natural porous structures such as marine skeletons as promising alternative bone graft substitute materials without any further mineralogical changes, or after partial or total transformation into calcium phosphate. The suitability of the marine-derived porous bone graft substitutes for the intended applications will be also discussed.

This study characterizes the microstructure and its associated crystallographic features of bulk maraging steels fabricated by selective laser melting (SLM) combined with a powder bed technique. The fabricated sample exhibited characteristic melt pools in which the regions had locally melted and rapidly solidified. A major part of these melt pools corresponded with the ferrite (alpha) matrix, which exhibited a lath martensite structure with a high density of dislocations. A number of fine retained austenite (gamma) with a <001> orientation along the build direction was often localized around the melt pool boundaries. The orientation relationship of these fine gamma grains with respect to the adjacent alpha grains in the martensite structure was (111) gamma // (011) alpha and [-101] gamma // [-1-11] apha (Kurdjumov–Sachs orientation relationship). Using the obtained results, we inferred the microstructure development of maraging steels during the SLM process. The results depict that new and diverse high-strength materials can be used to develop industrial molds and dies.

Gut bacteria play an important role in several metabolic processes and human diseases, such as obesity and its co-morbidities, like fatty liver disease, insulin resistance/diabetes and cardiovascular events. Among several factors, dietary patterns, probiotics, prebiotics, synbiotics, antimicrobials and non-dietary factors, such as stress, age, exercise and climatic conditions, can dramatically impact the human gut microbiota diversity and equilibrium. However, the effect of minor food constituents, including food additives and trace contaminants, on human gut microbiota has received less attention. Consequently, the present review aimed to provide an objective perspective of the current knowledge regarding the impacts of minor food constituents on human gut microbiota and consequently, on human health.

Minimizing optical losses in resonant cavities is crucial for improving photonic device performance. This study focuses on the development of a simulation tool to analyze scattering losses in Fabry-Pérot interferometers (FPI), offering precise modeling of waveguide dynamics and contributing to accurate loss predictions across various platforms. Optical cavities often suffer from scattering losses due to surface roughness and material defects. Our approach integrates theoretical models and simulations to quantify these losses, utilizing the FPI as a model system. We identified upper and lower reflectivity thresholds, beyond which accurate measurement of losses becomes unreliable. For reflectivity below a certain threshold, measurement errors arise, while excessively high reflectivity can reduce fringe visibility and introduce detector sensitivity issues. Simulations were used to validate the model's ability to predict reflectivity and attenuation in waveguides with varying loss levels. The software’s flexibility to adjust transmission parameters for different cavity configurations enhances its utility for a broad range of photonic systems. Our study offers a novel methodology for optical loss analysis, with practical applications in optimizing photonic devices. By providing a reliable tool for precise loss measurement, this work supports advancements in optical technologies, enabling the design of more efficient, high-performance devices across various applications.

Poor therapeutic outcomes have been attributed to inter-individual and interethnic variability in cytochrome P450 (CYP450)-dependent metabolism and altered drug retention associated with P-glycoprotein (P-gp). An individualized pharmacotherapeutic approach would benefit the genetically diverse South African population. The study aim was to develop a validated, targeted, analytical method to quantify seven probe drugs and their metabolites in dried blood spots (DBS) using the Mitra™ volumetric absorptive micro-sampling device for blood collection. An Agilent liquid chromatography (LC) system coupled to a Sciex 4000 QTRAP tandem mass spectrometer (MS) was used for method optimization and validation. Targeted LC-MS/MS methods were validated according to ICH guidelines. The validated LC-MS/MS method met the required bioanalytical standards for specificity, sensitivity, linearity, accuracy, precision, carry-over, and stability. This study successfully validated the use of DBS, collected with the Mitra™ microsampling device, to measure expected probe drug and metabolite concentrations using the “Geneva phenotyping cocktail” for the purpose of simultaneous phenotyping of in vivo CYP450 metabolic activity of the CYP1A2, -2B6, -2C9, -2C19, -2D6, and -3A4 enzymes, and P-gp transport activity. However, statistical analysis using Bland-Altman plots showed that not all analytes exhibited linear distribution pharmacokinetics between DBS and plasma, which influenced the predicted vs real plasma concentrations based on measurements in a DBS matrix. These findings were attributed to the blood-to-plasma concentration ratio, the physicochemical properties and stability of the analytes, and the extraction efficiency of the Mitra™ sampler. More research is required before DBS sampling can be substituted for conventional plasma sampling

Starvation of photoreceptors induced by reduced dysregulated ocular blood flow is proposed as a common pathway for the pathogenesis of retinitis pigmentosa (RP). The current study evaluated the safety and efficacy of ophthalmic nerve stimulation (ONS) as an ocular blood flow neuromodulator, combined with ascorbic acid (AA) as a potent anti-oxidant in the treatment of RP. Additionally, the initial characteristics of rod responders were identified. Forty participants with simple, non-syndromic RP presented with a characteristic triad of RP (the bone spicule pigmentation, attenuation of retinal blood vessels, and waxy optic disc pallor), were en-rolled in a prospective open-label single-armed interventional study. The severity of the disease was clinically graded into six stages. Patients with an established diagnosis of RP; aged ≥ 4 years, with best corrected visual acuity (BCVA) ≥ 20/400 were included. All participants were daily treated with bilateral ONS sessions combined with intravenous administration of AA for two weeks. The primary efficiency endpoint was 6 months’ changes in scotopic vision as measured by a 10-item, 100-point, Low Luminance Questionnaire-10 (LLQ-10). The secondary efficiency points included best corrected visual acuity (BCVA) and contrast sensitivity. Rod responders were defined by ≥ 25 points increment of LLQ-10 score at 6 months after treatment. The results showed that ONS combined with AA treatment significantly improved low luminance vision, BCVA, and contrast sensitivity in patients with RP (p≤ 0.05). At 6-month visit, twenty-four (60%) patients were identified as rod responders and 16 (40%) patients were rod-non-responders. The mean change in LLQ-10 score was (46.35 ±16.81) in rod responders versus (4.9 ± 7.6) in non-responders (p < 0.0001). A clinically significant improvement of BCVA (≥0.2 logMAR) and contrast sensitivity (≥0.3 log unit) were demonstrated in 50% of the right eyes of rod responders. No serious adverse effects were reported and headache in 5 patients (12.5%) was the only en-countered side effect in this study. In conclusion, ocular neuromodulation is a safe therapeutic strategy for RP. It significantly improved night vision, BCVA, and contrast sensitivity. Determinants of rod responders include a shorter duration of night blindness, an earlier stage of the disease, and a relatively thicker ganglion cell layer at baseline. Additionally, two therapeutic scenarios were recognized; an early disease-modifying intervention that restores night vision and reverses the disease process and a late cone rescue intervention that improves/maintains central vision.

Abstract: Pasteurella spp. is a gram-negative bacterium that is part of the oral and upper respira-tory tract microbiota of many animals such as canids and felines. In humans it can produce pa-thology primarily associated with animal bites or scratches. In addition, members of this genus, and especially Pasteurella multocida, may also be involved in systemic infections, mainly in im-munocompromised patients in close contact with pets. The aim of this study is to analyse the prevalence and clinical characteristics of infections caused by Pasteurella spp. as well as the sensitivity profile of these isolates obtained in the Microbiology laboratory of the Hospital Can Misses (Ibiza, Ibiza and Formentera Health Area, ASEF) in the period from January 2013 to December 2018. The group of islands of Ibiza and Formentera is known as the Pitiusas Islands. Retrospective descriptive study in which all Pasteurella spp. isolates were analysed in the Microbiology Laboratory of Hospital Can Misses from 1 January 2013 to 31 De-cember 2018. Bacterial identification was performed by Vitek 2 automated biochemical test panel (bioMérieux, Spain) and antimicrobial susceptibility by E-test or antibiotic discs in Mueller-Hinton blood agar, interpreted based on European Committee on An-timicrobial Susceptibility Testing (EUCAST) standards, 2022 version. Medical records were systematically reviewed by collecting demographic data of infected patients, comorbidities, epidemiological data and clinical features of the infection. A total of 22 isolates of Pasterurella spp. were obtained from 22 different patients, 62.8% female, from three different species: 18 P. multocida, 2 P. canis and 2 P. pneumo-tropica. Most isolates came from soft tissue infection samples: 7 wound exudates and 5 abscess material. The antibiotics tested with the highest sensitivity profile were gen-tamicin and cefepime (100% sensitivity). The species most commonly isolated in our environment is P. multocida. Close contact with companion animals, especially cats and dogs, is the main risk factor for Pasteurella spp. infections, although in many cases such contact cannot be established. So Pasteurella spp. infection should be considered a zoonosis in possible emergency, especially in rural areas such as Pitiusas Islands.

We introduce the notion of p-adic magic contraction on p-adic Hilbert space. We derive p-adic Halmos dilation, p-adic Egervary N-dilation, p-adic von Neumann inequality and p-adic Sz.-Nagy dilation for p-adic magic contraction.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

Ischemia stroke is one of a clinically common cerebrovascular disease. And Inhibition of brain tissue ischemia and reperfusion-induced damage, especially apoptosis, has an irreplaceable protective effect on ischemic nerves, and has special significance for the treatment of patients after treatment. However, the development of neuroprotective drugs still has certain challenges. Radix scrophulariae as a valuable medicine, has been discovered to has neuroprotective effects. Our researches initially proved that Radix scrophulariae aqueous extract (RSAE) exerting a neuroprotective effects on cerebral ischemia and reperfusion (I/R) injury in oxygen glucose deprivation and reperfusion (OGD/R)-induced PC12 cells and middle cerebral artery occlusion/reperfusion (MCAO/R) model mice, were associated with attenuation of infarct volume, brain water content, nitric oxide (NO) and malondialdehyde (MDA), inhibiting I/R-induced damage by reducing the levels of LDH release, improving anti-oxidant capacity by upregulating the SOD, GSH-Px and CAT activity, stabilizing mitochondrial membrane potential, reducing neuronal apoptosis, necrosis and neuronal loss by regulating the expression of anti-apoptotic BCL-2and pro-apoptotic protein Bax, and elucidating downregulate the phosphorylation levels of MAPK pathways. Our findings may elaborate the neuroprotective effects and potential mechanisms of RSAE on focal cerebral I/R injury in mice. Since, Radix scrophulariae, as a potential neuroprotective natural plant, has originally been identified to, our results may offer directions and clues for discovering new active compounds or drugs for treatment of ischemic stroke, which allows us to discover many new natural active chemicals by chemical separation and identification, and provide new insights into therapeutic targets in stroke patients.

Customized wrist splints, particularly for upper extremity orthoses like wrist support braces, are commonly used across numerous clinical scenarios. However, the traditional process for producing personalized wrist splints is largely manual and highly dependent on the expertise of orthopedic specialists. This experience-based approach often leads to suboptimal outcomes, necessitating further refinement of the designs. Recent advancements in Additive Manufacturing (AM) have brought significant innovation to various industries, including orthopedics. This study aims to present a comprehensive methodology that integrates advanced design tools ,like 3D Scanning, with digital manufacturing techniques to produce tailored wrist splints. The produced hand brace aims to offer enhanced mechanical performance and comfort by precisely fitting an individual’s anatomy while minimizing material usage and weight. To achieve optimal design efficiency, the study explores the application of a Topology Optimization (TO) approach for design, while the manufacturing process utilizes Fused Deposition Modeling (FDM), an evolving technology within the Additive Manufacturing (AM) sector.

3D Printing /Additive manufacturing holds a promising future in healthcare as it aids in visualizing things and making 3D objects which is very important in different areas of medicine. The concept of one size fits all has failed the quality of care delivered by us in healthcare which demands customised needs for patient care to create 3D printed tissues, make personalized prosthetics, implants and physical models of the human body. The materials used for printing models and other healthcare devices for medical education, patient needs, and prototyping are increasing. The application of different materials for use in healthcare is not studied. New materials are also available for the various applications in healthcare industry. This experimental study was conducted to review the nine distinct 3D printing filament materials like PETG, PA, ABS, PLA, HIPS, PMMA, Ceramic, Carbon Fiber, and (PLA + Metal Composite) with the help of a 3D printed physical model of T-12 thoracic vertebrae using all the abovementioned materials. The evaluation of materials was based on diverse mechanical properties, applications across medical fields, performance metrics, costs, accuracy, and quality. The assessment This study also focuses on comparison of mechanical properties such as tensile strength, compressive strength of the abovementioned materials with human bone. The study also reviews the 3D printing process and explores its utilization in biomedical applications. The Insights about the application of various materials holds a promising future for development of newer materials for healthcare industry.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Sub-micro dislocation cellular structures formed during rapid solidification break the strength-ductility trade-off in laser powder bed fusion (LPBF)-processed 316L stainless steel through high-density dislocations and segregated elements or precipitates at the cellular boundaries. The high-density dislocation entangled at the cellular boundary accommodates solidification strains among the cellular structures and cooling stresses through elastoplastic deformation. Columnar grains with cellular structures typically form along the direction of thermal flux. However, the ultra-low misorientations between the adjacent cellular structures and their interactions with the cellular boundary formation remain unclear. In this study, we revealed the ultra-low misorientations between the cellular structures in LPBF-processed 316L stainless steel using conventional electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), and transmission electron microscopy (TEM). The conventional EBSD and TKD analysis results could provide the misorientation angles smaller than 2° while the resolution mainly depends on the specimen quality and scanning step size, and so on. TEM technique with higher spatial resolution provides accurate information between adjacent dislocation cells with misorientation angles smaller than 1°. This study presents that TEM method is the better and more precise analysis method of the misorientation measurement of the cellular structures and provides insights into measuring the small misorientation angles between adjacent dislocation cells and nanograins in nanostructured-metals and alloys with ultrafine-grained microstructures.

CubeSats, known for their compact size and cost-effectiveness, have gained significant popularity. However, their limited size imposes restrictions on optical aperture and, consequently, Ground Resolution Distance in Earth Observation missions. To overcome this limitation, the concept of deployable optical payloads with segmented primary mirrors which can unfold like petals has emerged, enabling larger synthetic apertures and enhanced spatial resolution. This study explores the potential benefits of leveraging Additive Manufacturing (AM) and Topology Optimization (TO) in the realm of ultra-precision machining, specifically single point diamond machining. The goal is to reduce fixture weight while improving stiffness to minimize deformations caused by rotational and cutting forces which compromise optical performance. Through Finite Element Analysis, this research compares conventionally machined fixtures with those produced using AM and TO techniques. The results reveal that concept designs created through TO can achieve a remarkable 68% reduction in weight. This reduction makes the assembly, including the machining fixture and 12U deployable segments, manageable by a single operator without the need for specialized lifting equipment. Moreover, these innovative designs lead to substantial reductions of up to 86% and 51% in deformation induced by rotational and cutting forces, respectively.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

There is an intense need to optimize agrivoltaic systems. This article describes the invention of a new testing system: the parametric open source cold-frame agrivoltaic system (POSCAS). POSCAS is an adapted gardening cold-frame used in cold climates as it acts as a small greenhouse for agricultural production. POSCAS is designed to test partially transparent solar photovoltaic (PV) modules targeting the agrivoltaic market. It can both function as a traditional cold frame, but it can also be automated to function as a full-service greenhouse. The integrated PV module roof can be used to power the controls or it can be attached to a microinverter to produce power. POSCAS can be placed in an experimental array for testing, agricultural and power production. It can be easily adapted for any type of partially transparent PV module. An array of POSCAS systems al-lows for testing agrivoltaic impacts from the percent transparency of the modules by varying the thickness of a thin film PV material or the density of silicon-based cells, and various forms of optical enhancement, anti-reflection coatings and solar light spectral shifting materials in the back sheet. All agrivoltaic variables can be customized to identify ideal PV designs for a given agricultural crop.

The effectiveness of forest resources depends on the comprehensiveness and rationality of their consumption and processing into finished products. This article discusses a problem of utilising solid fir wood greenery residues generated during the industrial production of essential oils. Bioconversion is considered to be the most promising utilization method. The objective of this research was to study the chemical composition of bioconversion products of fir wood greenery-based substrates. The РР-3.2 strain of Pleurotus pulmonarius (Fr.) Quél was used as a biodestructor. In the process of bioconversion, the contents of polysaccharides and lignin substances is reduced to 38 and 28 % respectively. Up to 20 % of protein accumulates in bioconversion products of fir wood greenery. The amount of nucleic acids is not more than 1.5 g per 1 kg, the contents of heavy metals, such as mercury, cadmium, arsenic, lead, do not exceed maximum permissible concentration standards. The substrate weight loss reaches 15 %. When fallen leaves and post-extraction poplar bud residues are added to the substrate, the substrate-destroying activity of fungi rises, as well as the protein content increases by 3 %. The digestibility of products as a result of bioconversion increases 1.6–2.8 times depending on the substrate composition. The obtained data enable to recommend post-fermented substrates based on fir wood greenery and balsam poplar biomass for use as a protein feed additive.

In this work, the manufacture of thin walls with sharp corners has been optimized by adjusting the limits of a 3-axis cartesian kinematics through data recorded and analyzed off-line, such as axis speed, acceleration and the positioning of the X and Y axes. The study was carried out with two powder materials (SS316L and IN718) using the directed energy deposition process with laser. 1 mm thick walls were obtained with only one bead per layer and straight/sharp corners at 90º. After adjusting the in-position parameter G502 for positioning precision on the FAGOR 8070 CNC system, it has been possible to obtain walls with minimal accumulation of material in the corner, and with practically constant layer thickness and height, with a radii of internal curvature between 0.11 and 0.24 mm for two different precision configuration. The best results have been obtained by identifying the correct balance between the decrease in programmed speed and the precision in the positioning to reach the point defined as wall corner, with speed reductions of 29% for a programmed speed of 20 mm/s and 61% for a speed of 40 mm/s. The walls show minimal defects such as residual porosities, and the microstructure is adequate.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The thermal stabilizers, lubricant, and plasticizers are three crucial additives for processing poly (vinyl chloride) (PVC). In this study, a new mannitol stearate ester-based aluminum alkoxides (MSE-Al) was designed and synthesized as a novel additive for PVC. The thermal stability and processing performance of PVC stabilized by MSE-Al were evaluated by Congo red test, conductivity measurement, thermal aging test, ultravioletevisible (UV-vis) spectroscopy test, and torque rheometer test. Results showed that the addition of MSE-Al can not only markedly improve the long-term thermal stability of PVC, but also greatly accelerate the plasticizing and decrease the balance torque which demonstrated that MSE-Al possesses the lubricating property. Thus, MSE-Al was demonstrated to be able to provide tri-functional additive roles, e.g., thermal stabilizer, plasticizer, and lubricant. The test results for the thermal stability of PVC indicated that the initial whiteness of PVC stabilized with MSE-Al was not good enough, thus the synergistic effect of MSE-Al with zinc stearates (ZnSt₂) on the thermal stability of PVC was also investigated. The results showed that there exhibited an appreciable synergistic effect between MSE-Al and ZnSt₂. The thermal stabilization mechanism and synergism effect of MSE-Al with ZnSt₂ were then discussed.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

This work explores an additive-manufacturing-enabled combination-of-function approach for design of modular products. AM technologies allow the design and manufacturing of nearly free-form geometry, which can be used to create more complex, multi-function or multi-feature parts. The approach presented here replaces sub-assemblies within a modular product or system with more complex single parts that are designed and manufactured using AM technologies. This approach can increase the reliability of systems and products by reducing the number of interfaces, as well as allowing the optimization of the more complex parts during the design. The smaller part count and the ability of users to replace or upgrade the system or product parts on-demand should reduce user risk, life-cycle costs, and prevent obsolescence for the user of many systems. This study presents a detailed review on the current state-of-the-art in modular product design in order to demonstrate the place, need and usefulness of this AM-enabled method for systems and products that could benefit from it. A detailed case study is developed and presented to demonstrate the concepts.

Selective laser melting (SLM) is one of the widely used techniques in metallic additive manufacturing, in which high-density laser powder is utilized to selectively melting layers of powders to create geometrically complex parts. Temperature distribution and molten pool geometry directly determine the balling effect, and concentrated balling phenomenon significantly deteriorates surface integrity and mechanical properties of the part. Finite element models have been developed to predict temperature distribution and molten pool geometry, but they were computationally expensive. In this paper, the three-dimensional temperature distributions are predicted by analytical models using point moving heat source and semi-ellipsoidal moving source respectively. The molten pool dimensions under various process conditions are obtained from the three-dimensional temperature predictions and experimentally validated. Ti-6Al-4V alloy is chosen for the investigation. Good agreements between the predictions and the measurements are observed. The presented models are also suitable for other metallic materials in the SLM process.

Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimum material and, many times, with process time reduction. Besides, as the additive and subtractive operations are carried out in the same machine, without moving the part, dead times are reduced and higher accuracies are achieved. However, it is not clear whether the direct material deposition after the machining operation is possible or intermediate cleaning stages are required because of the possible presence of residual cutting fluids. Therefore, different LMD tests are performed on a part impregnated with cutting fluid, both directly and after the removal of the coolant by techniques such as laser vaporizing and air blasting. The present work studies the influence of the cutting fluid in the LMD process and the quality of the resulting part. Resulting porosity is evaluated and it is concluded that if the part surface is not properly clean after the machining operation, deficient clad quality can be obtained in the subsequent laser additive operation.

The present paper discusses an elliptic equation with Steklov boundary conditions and $(p(x),q(x))$-Laplacian. Using mountain pass theorem together with Ekeland's variational principle, we prove, under appropriate conditions on the functions involved, that the problem admits at least two solutions.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

In this study, we obtained results for the computation of eigen-pairs, singular value decomposition, pseudo-inverse, and the least square problem for elliptic quaternion matrices. Moreover, we established algorithms based on these results and provided illustrative numerical experiments to substantiate the accuracy of our conclusions. In the experiments, it was observed that the p-value in the algebra of elliptic quaternions and elliptic numbers directly affects the performance of the problem under consideration. Selecting the optimal p-value for problem-solving and the elliptic behavior of many physical systems make this number system advantageous in applied sciences.

Using assembly theory, we investigate the assembly pathways of binary strings of length N formed by joining bits present in the assembly pool and the strings that entered the pool as a result of previous joining operations. We show that the string assembly index is bounded from below by the shortest addition chain for N, and we conjecture about the form of the upper bound. We define the degree of causation for the minimum assembly index and show that for certain N it features regularities that can be used to determine a shortest addition chain. We show that a string with the smallest assembly index for N can be assembled by a binary program of length equal to this index if the length of this string is expressible as a product of Fibonacci numbers. We conjecture that there is no binary program that has a length shorter than the length of the string having the largest assembly index for N that could assemble this string. The results confirm that four Planck areas provide a minimum information capacity that corresponds to a minimum thermodynamic (Bekenstein-Hawking) entropy. Knowing that the problem of determining the assembly index is at least NP-complete, we conjecture that this problem is NP-complete, while the problem of creating the string so that it would have a predetermined largest assembly index is NP-hard. The proof of this conjecture would imply P ≠ NP, since every computable problem and every computable solution can be encoded as a finite binary string.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Inhibition of quorum sensing (QS)-dependent biofilm formation and virulence is extensively investigated as a novel approach to combat bacterial pathogens by impeding their ability to cause antibiotic-tolerant diseases. Such strategies are considered a promising alternative to conventional antibacterial therapy since interrupting the central cell-to-cell communication system imposes less selective pressure on the target pathogen. In this study, novel hybrid compounds composed of anthranilic acids substituted with halogens at different positions of the phenyl ring, and 4-(2-aminoethyl/4-aminobuthyl)amino-7-chloroquinoline linked via 1,3,4-oxadiazole were synthesized using standard procedures. Their anti-QS activities were evaluated using Chromobacterium violaceum ATCC31532 (anti-biofilm and bactericidal activities) and Pseudomonas aeruginosa PAO1 (anti-biofilm/-virulence activities). The results showed that compounds 15–19 and 23 inhibited the production of violacein, the QS-inducible pigment, in C. violaceum to a similar extent as the model QS inhibitor - quercetin (83.5–90%). Compound 15 exhibited the strongest effect on P. aeruginosa in the anti-biofilm screening, reducing its ability to form biofilm by almost 50%, while compounds 16 and 19 were able to reduce the biofilm formation by approximately 30%. However, compound 23 did not demonstrate significant anti-biofilm activity and only inhibited pyocyanin production in P. aeruginosa. In conclusion, this study suggests that 1,3,4-oxadiazoles 15, 16, and 19 are the most promising compounds for future research as novel QS inhibitors against Gram-negative bacteria equipped with different QS signaling pathways.

A simple and sensitive liquid chromatography-tandem mass spectrometry (LC– MS/MS) method has been developed for the simultaneous determination of atorvastatin (ATOR), ezetimibe (EZM) and their three metabolites including o-hydroxyl atorvastatin (o-OH ATOR), p-hydroxyl atorvastatin (p-OH ATOR), and ezetimibe-glucuronide (EZM-G) in human plasma using benzyl paraben (BP) as internal standard (IS). The analytes and IS were ionized using ESI positive ion mode (ATOR, o-OH ATOR, and p-OH ATOR), ESI negative ion mode (EZM, EZM-G, and BP), and operated in multiple reaction monitoring (MRM) mode. They were next extracted by salting-out assisted liquid–liquid extraction with acetonitrile, and then analyzed by liquid chromatography on a reversed-phase chromatographic column (50 mm × 4.6 mm; 3.5 µm), using a mixture of ac-etonitrile and an acetic acid solution (0.5%) as the mobile phase, showing high extraction effi-ciency (>70%), and a minimized matrix effect. The method was satisfactorily validated, and showed excellent linearity over wide concentration ranges of 0.06–15 ng/mL, 0.6–150 ng/mL, 0.4–100 ng/mL, 0.12–30 ng/mL, and 0.05–3 ng/mL for EZM, EZM-G, ATOR, o-OH ATOR, and p-OH ATOR, respectively.

BackgroundIt is unclear what underpins the large global variations in the prevalence of fluoroquinolone resistance in gram-negative bacteria. We tested the hypothesis that different intensities in the use of quinolones for food-animals plays a role. MethodsWe used Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in human infections with Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa was correlated with the use of quinolones for food producing animals. Linear regression was used to assess the relative contributions of country-level quinolone consumption for food-animals and humans on fluoroquinolone resistance in these 4 species. ResultsThe prevalence of fluoroquinolone resistance in each species was positively associated with quinolone use for food-producing animals (E. coli [ρ=0.55; P<0.001], K. pneumoniae [ρ=0.58; P<0.001]; A. baumanii [ρ=0.54; P=0.004]; P. aeruginosa [ρ=0.48; P=0.008]). Linear regression revealed that both quinolone consumption in humans and food animals were independently associated with fluoroquinolone resistance in E. coli and A. baumanii. ConclusionsReducing quinolone use in food-producing animals may help retard the spread of fluoroquinolone resistance in various gram negative bacterial species.

In this paper, the notion of θ∗-weak contraction is introduced, which is utilized to prove some fixed point results. These results are helpful to give a positive response to certain open question raised by Kannan [Amer. Math. Monthly 76:1969] and Rhoades [Contemp. Math. 72:1988] on the existence of contractive definition which does not force the mapping to be continuous at the fixed point. Some illustrative examples are also given to support our results. As applications of our result, we investigate the existence and uniqueness of a solution of non-linear matrix equations and integral equations of Volterra type as well.

Different contact materials along with optimization of the deposition techniques expand the possibilities to obtain high performance room temperature CdTe-based X/γ-ray detectors. The heterostructures with ohmic (MoOx) and Schottky (MoOx, TiOx, TiN, and In) contacts, created by DC reactive magnetron sputtering and vacuum thermal evaporation, as well as In/CdTe/Au diodes with a p-n junction, formed by laser-induced doping, were developed and investigated. Depending on the pre-treatment of the surface of semi-insulating p-CdTe crystals, deposition of a MoOx film formed an ohmic or Schottky contact. Based on the calculations and IV characteristics of the fabricated Mo-MoOx/р-CdTe/MoOx-Mo, In/CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo Schottky-diode detectors, the current transport processes were described in the models of the carrier generation-recombination within the space-charge region (SCR) at low bias voltages, and space-charge limited current at higher voltages, respectively. The energies of generation–recombination centers, density of trapping centers, and carrier lifetimes were determined. A sharp increase in the reverse current in the Mo-MoOx/р-CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo heterostructures at high bias was discussed in frames of the Poole–Frenkel emission model. Nanosecond laser irradiation of the In electrode, pre-deposited on the p-CdTe crystals, resulted in an increase in the voltage range, corresponding to the carrier generation-recombination in the SCR, in the IV characteristics of the In/CdTe/Au diodes. Such In/CdTe/Au p-n junction diodes demonstrated high energy resolutions (7%@59.5 keV, 4%@122 keV, and 1.6%@662 keV).

Arabidopsis contains eight different h-type thioredoxins (Trx) being distributed in different cell organelles. Although Trx h2 is deemed to be localized in mitochondria, its subcellular localization and function remains a matter of debate. Here, Trx h2 localization and function were investigated using cell fractionation studies and reverse genetics. Differential centrifugation and immunodetection showed the Trx h2 protein to be distributed to the microsomal fraction rather than to mitochondrial preparations. To analyze whether Trx h2 has different roles than mitochondrial Trxs, Arabidopsis mutants lacking Trx h2 were compared with mutants deficient in mitochondrial Trx o1 and double mutants with joint deficiencies in both Trxs. Under constant medium light, trxh2 grew as the wild type, while trxo1 and trxo1h2 mutants showed impaired growth. This was accompanied by differences in the metabolite profiles. The trxo1 and trxo1h2 mutants clustered differently from the wild type during the night, revealing a decrease in ascorbate and glutathione redox states. In fluctuating light intensities, genotypic differences in growth rates were attenuated. Compared to the wild type, the fluctuating-light induced decrease in the NADPH/NADP ratio was diminished in the mutants, with the trxo1h2 double mutant showing the strongest effect. This was accompanied by an increase in the photosynthetic efficiency of the trxo1h2 mutant, specifically in the high light phases of fluctuating light. Conclusively, these results support the view that Trxs o1 and h2 are localized in different subcellular compartments, and have different effects on ascorbate and glutathione redox states and growth in medium light, but cooperatively affect NADP(H) redox state and photosynthetic efficiency in fluctuating light.

Transforming growth factor beta (TGF-β) is a determinant for inflammation and fibrosis in cardiac and skeletal muscle in Chagas disease. To determine its regulatory mechanisms, we investigated the response of T. cruzi-infected cardiomyocytes (CM), cardiac fibroblasts (CF) and L6E9 skeletal myoblasts to TGF-β. Cultures of CM, CF and L6E9 were infected with T. cruzi (Y strain) and treated with TGF-β (1–10 ng/mL, 1h or 48 h). Fibronectin (FN) distribution was analyzed by immunofluorescence and Western blot (WB). Phosphorylated SMAD2 (PS2), phospho-p38 (p-p38), and phospho-c-Jun (p-c-Jun) signaling were evaluated by WB. CF and L6E9 showed an increase in FN from 1 ng/mL of TGF-β, while CM displayed FN modulation only after 10 ng/mL treatment. CF and L6E9 showed higher PS2 levels than CM, while p38 is less stimulated in CF than CM and L6E9. After T. cruzi infection, localized FN disorganization was observed in infected CF and L6E9. T. cruzi induced an increase in FN in CF cultures, mainly in uninfected cells. Infected CF cultures treated with TGF-β showed a reduction in PS2 and an increase in p-p38 and p-c-Jun levels. Our data suggest that p38 and c-Jun pathways may be participating in the fibrosis regulatory process mediated by TGF-β after T. cruzi infection.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this paper, we study the p-adic integral representation on Z_p of q-Bernoulli numbers arising from two variable q-Bernstein polynomials and investigate some properties for the q-Bernoulli numbers. In addition, we give some new identities of q-Bernoulli numbers.

In the present paper, we introduce (p, q)-extension of Apostol type Frobenius-Euler polynomials and numbers and investigate some basic identities and properties for these polynomials and numbers, including addition theorems, difference equations, derivative properties, recurrence relations and so on. Then, we provide integral representations, explicit formulas and relations for these polynomials and numbers. Moreover, we discover (p, q)-extensions of Carlitz's result [L. Carlitz, Mat. Mag., 32 (1959), 247–260] and Srivastava and Pintér addition theorems in [H. M. Srivastava, A. Pinter, Appl. Math. Lett., 17 (2004), 375–380].

Using polymethylmethacrylate (PMMA) bone cement is widespread in orthopedic surgeries for implant fixation and as a carrier for antibiotic delivery to prevent and treat infections. This review comprehensively evaluates in vitro studies investigating the antibiotic elution profiles and mechanical properties of PMMA bone cement. We explore the kinetics of antibiotic release, factors influencing elution efficiency, and the impact of various antibiotics on the mechanical properties of PMMA composites. At the same time, we examine how the inclusion of antibiotics affects the mechanical integrity of PMMA, including parameters such as compressive strength, tensile strength, and fatigue resistance. Through a detailed analysis of these studies, this review aims to provide insights into optimizing PMMA bone cement formulations for enhanced therapeutic efficacy and structural performance.

In metal additive manufacturing (AM), precise temperature field prediction is crucial for process monitoring, automation, control, and optimization. Traditional methods, primarily offline and data-driven, struggle with adapting to real-time changes and new process scenarios, which limits their applicability for effective AM process control. To address these challenges, this paper introduces the first physics-informed (PI) online learning framework specifically designed for temperature prediction in metal AM. Utilizing a physics-informed neural network (PINN), this framework integrates a neural network architecture with physics-informed inputs and loss functions. Pretrained on a known process to establish a baseline, the PINN transitions to an online learning phase, dynamically updating its weights in response to new, unseen data. This adaptation allows the model to continuously refine its predictions in real-time. By integrating physics-informed components, the PINN leverages prior knowledge about the manufacturing processes, enabling rapid adjustments to process parameters, geometries, deposition patterns, and materials. Empirical results confirm the robust performance of this PI online learning framework in accurately predicting temperature fields for unseen processes across various conditions. It notably surpasses traditional data-driven models, especially in critical areas like the Heat Affected Zone (HAZ) and melt pool. The PINN’s use of physical laws and prior knowledge not only provides a significant advantage over conventional models but also ensures more accurate predictions under diverse conditions. Furthermore, our analysis of key hyper-parameters—learning rate and batch size of the online learning phase—highlights their roles in optimizing the learning process and enhancing the framework’s overall effectiveness. This approach demonstrates significant potential to improve the online control and optimization of metal AM processes.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

In recent years, there has been a wave of research on complex networks. The purpose of this paper is to study the graph theoretic mathematical properties of random cyclooctatetraene chain. We obtain the explicit analytical expressions for the variances of the Gutman index, Schultz index, multiplicative degree-Kirchhoff index and additive degree-Kirchhoff index of a random cyclooctatetraene chain with $n$ octagons, which plays a crucial role in the research and application of topological indices.

The osseointegration process in and around additively manufactured (AM) lattice structures of a new titanium alloy, Ti–19Nb–14Zr, was evaluated. Three different implants, including lattices with increasing high sidewalls gradually closing them, were designed, manufactured and implanted in the tibia and metatarsal bone of two sheep for twelve weeks. After removal, they were characterized with X-ray computed tomography (XCT). The 3D XCT images were segmented using machine learning. The bone-interface implant (BII) and bone-implant contact (BIC) were studied. The results show that, since AM naturally leads to high roughness surface finish, the wettability of the implant is increased. The new alloy possesses an increased affinity to the bone enhancing the quality of osseointegration. The lattice provides crevices, in which the biological tissue can jump in and cling. The combination of these factors is pushing ossification beyond its natural limits. Therefore, the quality and speed of the ossification and osseointegration in and around these Ti–19Nb–14Zr AM laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

During submerged laser peening using a pulsed laser, a bubble that behaves like cavitation is generated after laser ablation (LA). The bubble is referred to as laser cavitation (LC). The amplitude of the shock-wave in LA water is larger than that of LC; however, the impact passing through the target metal during LC is larger than that of LA. Thus, submerged laser peening is referred to as “laser cavitation peening”, as the peening method using the cavitation impact is known as “cavitation peening”. The impact induced by a hemispherical bubble is more aggressive than that of a spherical bubble with a microjet. Laser cavitation peening can improve the fatigue strength of metallic materials by producing work-hardening and the introduction of compressive residual stress. Three-dimensional additive manufactured metals (3D metals) such as titanium alloy are attractive materials for aviation components and medical implants; however, the fatigue strength of as-built components is nearly half that of bulk metals, and this is an obstacle for the applications of 3D metals. In the present study, published research papers were reviewed to identify the key factors of laser cavitation peening, with additional visualization of LC and data. Then, improvements in the fatigue strength of metallic materials, including 3D metals produced by laser cavitation peening, were summarized.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

This paper discusses a possible approach to validate the Goldbach conjucture which states that all even numbers can be expressed as a summation of two prime numbers. For this purpose the paper begins with the concept of successive-addition-of-digits-of-an-integer-number (SADN) and its properties in terms of basic algebraic functions like addition, multiplication and subtraction. This concept of SADN forms the basis for classifying all odd numbers into 3 series- the S1, S3 and S5 series- which comprise of odd numbers of SADN(7,4,1), SADN(3,9,6) and SADN(5,2,8) respectively and follow a cyclical order. The S1 and S5 series are of interest in the analysis since they include both prime and composite numbers while the S3 series exclusively consists of composite numbers. Furthermore, the multiplicative property of SADN shows why composites on the S1 series are derived as products of intra-series elements of the S1 and S5 series while composites on the S5 series are derived as products of inter-series elements of the S1 and S5 series. The role of SADN is also important in determining the relevant series for identifying the combination of primes for a given even number since it shows why such combinations for even numbers of SADN(1,4,7) will be found on the S5 series while those for even numbers of SADN(2,5,8) will lie on the S1 series and both the series have a role to play in identifying the prime number combinations for even numbers with SADN(3,6,9). Thereafter, the analysis moves to calculating the total number of acceptable combinations for a given even number that would include combinations in the nature of two composites (c1+c2), one prime and one composite (p+c) and two primes (p1+p2). A cyclical pattern followed by even numbers is also discussed in this context. Identifying the c1+c2 and p+c combinations and thereafter subtracting them from the total number of combinations will yield the number of p1+p2 combinations. For this purpose the paper discusses a general method to calculate the number of composites on the S1 and S5 series for a given number and provides a detailed method for deriving the number of c1+c2 combinations. The paper presents this analysis as a proof to validate the Goldbach conjecture. Since even numbers can be of SADN 1 to 9 and the relation between nTc (i.e. total number of acceptable combinations) and nc(i.e. number of composites) for all even numbers can either be of nTc > nc or nTc ≤ nc, the paper shows that the Goldbach conjecture is true for both these categories of even numbers. In this manner this analysis is totally inclusive of all even numbers in general terms and since the analysis of every even number is common in methodology but unique in compilation, apart from being totally inclusive, it is also mutually exclusive in nature. This proves that the Goldbach conjecture which states that all even numbers can be expressed as atleast one combination of two prime numbers holds true for all even numbers, across all categories possible. Additionally this approach proves that the identification of p1+p2 combinations which would validate the Goldbach conjecture lies in the identification of c1+c2 combinations.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

HDPE (high-density polyethene) plastic waste is stronger, harder, and more resistant to high temperatures than other plastics. Using it as an additive in a concrete mixture is one solution to reduce this type of waste. We examined how HDPE-type plastics can be used as an additive material in the manufacture of concrete to improve its hardness, tensile strength and compressive strength. Using 156 samples, we aimed to identify the effect of HDPE plastic fibres on concrete of three qualities; B0, f'c10 MPa (low quality), and f'c25 MPa (medium and high quality). We added four compositions (2.5%, 5%, 10% and 20% by weight of cement) of HDPE plastic fibre to each quality of cement, with HDPE plastic fibre sizes of 1 x 1 cm, 0.5 x 2 cm or 0.25 x 4 cm. We found that the addition of 5% HDPE plastic fibre with a 0.5 x 2 cm cross-sectional shape to the f'c10 MPa concrete gives the best result, with increased tensile and compressive strength of the concrete.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Laser metal deposition with wire (LMD-w) is a developing additive manufacturing (AM) technology that has a high deposition material rate and efficiency, and is suitable for fabrication of large aerospace components. However, control of material properties, geometry, and residual stresses is needed before LMD-w technology can be widely adopted for the construction of critical structural components. In this study, we investigated the effect of interlayer cooling time, clamp constraints, and tool path strategy on part distortion and residual stresses in large-scale laser additive manufactured Ti-6Al-4V components using finite element method (FEM). The simulations were validated with the temperature and the distortion measurements obtained from a real LMD-w process. We found that a shorter interlayer cooling time, full clamping constraints on the build plates, and a bidirectional tool path with 180⁰ rotation minimized part distortion and residual stresses and resulted in symmetric stress distribution.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

Soil water balance (SWB) in woody crops is sometimes difficult to estimate with one-dimensional models because these crops do not completely cover the soil and usually have a deep root system, particularly when cropped under rainfed conditions in a Mediterranean climate. In this study, the actual crop evapotranspiration (ETc act) is estimated with the soil water balance model SIMDualKc which uses the dual-Kc approach (relating the fraction of soil cover with the crop coefficients) to improve the estimation of the water requirements of a rainfed vineyard, using data from a deep soil profile. The actual basal crop coefficient (Kcb act) obtained using the SIMDualKc model was compared with the Kcb act estimated using the A&amp;P approach, which is a simplified approach based on measurements of the fraction of ground cover and crop height. Spectral vegetation indices derived from Landsat-5 satellite data were used to determine the fraction of ground cover (fc VI) and thus, the density coefficient (Kd). The SIMDualKc model was calibrated using soil water content (SWC) measurements down to a depth of 1.85 meters, which significantly improved the conditions for using a SWB estimation model. The test of the model was performed using a different SWC dataset. A good agreement between simulated and field measured SWC was observed for both data sets along the crop season, with RMSE&lt;12.0 mm, NRMSE &lt;13%. The calibrated Kcb values were 0.15, 0.60 and 0.52 for the initial, mid-season, and end season, respectively. The ratio between actual (ETc act) and crop evapotranspiration (ETc) was quite low between veraison and maturity (mid-season), corresponding to 36%, indicating that the rainfall was not sufficient to satisfy the vineyards water requirements. Spectral vegetation indices used to compute fc VI were unable to fully track the plants’ conditions when water stress. However, ingestion of data from remote sensing showed promising results that could be used to support decisions making in irrigation scheduling. Further studies on the use of the A&amp;P approach using remote sensing data are required.

Photovoltaic materials convert light into electrical voltages. So far, most research in the field are focused on how to refine/improve the existing or standard photovoltaic cells to yield more efficient electricity, to reduce weight, to make more flexible shape, or to minimize costs under standard and uniform sunlight illuminations. In this project, we explore and demonstrate a hypothesis that non-uniform light illumination photovoltages can also be generated due to photo doping induced mobile charge carrier density gradient between light and dark areas in either p-type or n-type photo doping semiconductors. The term non-uniform light illumination was coined to refer to subjecting our photo sensing thin film devices to areas of high and low intensities of light illumination simultaneously, with an intention of creating a charge density gradient and therefore a voltage. Specifically, a polymeric composite thin film composed of P3HT (p-type photo doping semiconductor) and PCBM (photo doping electron acceptor and trap) at varying p-doping levels were studied. We observed that the fabricated photovoltaic cells with about 80% PCBM doped P3HT thin film devices exhibited 0.5-1.2 volts photovoltages under non-uniform light illuminations.

Background. ADHD is a neurodevelopmental disorder that is accompanied by executive deficits. Objectives. To obtain evidence of the usefulness of the BRIEF-P and to analyse the possible ceiling and floor effect of its scores in the assessment of executive function in preschoolers with signs compatible with a possible diagnosis of ADHD. Methods. Seven articles were selected from 2538 potentially eligible articles from different databases. We included studies assessing samples of individuals with symptoms compatible with ADHD, with age range 2-6 years, published in English or Spanish, during the period 2012-2022. References published in: Science Direct, NCBI (PubMed), ProQuest Education Journals in the last decade. Risk of bias was assessed using the QUADAS-2 questionnaire. The main variables were: age and executive functioning. Conclusions. Executive deficits in early-life individuals with ADHD-compatible symptoms are more extensive than deficits in working memory. BRIEF-P is an instrument that facilitates obtaining a sensitive and discriminative executive profile. It should be used in combination with other neuropsychological performance tests, finding a floor effect in tests associated with warm executive functions and a ceiling effect in cold executive functions. This requires using a variety of tests to assess executive performance in preschoolers with symptoms compatible with ADHD and designing intervention proposals in line with them...

Neuroinflammation is considered to be a significant component in a range of neuropathologies. Unfortunately, whilst its role is well recognized, the options for therapeutic intervention are limited. As such, there is a need to identify novel targets in order to increase treatment options. Given its role as both a neurotransmitter and an immune modulator, substance P and its NK1 receptor have been widely studied as a potential therapeutic target. There is evidence that NK1 receptor antagonists may exert beneficial effects in a range of conditions, including traumatic brain injury and stroke. Blocking the NK1 receptor has been shown to reduce blood-brain barrier dysfunction, reduce cerebral oedema, and reduce the levels of pro-inflammatory cytokines. These actions are associated with improved survival and functional outcomes. The NK1 receptor has also been shown to be involved in the inflammatory reaction to CNS infection, and hence antagonist may have some benefit in reducing infection-driven inflammation. However, the NK1 receptor may also play a role in the host immune response to infection, and so here, the potential beneficial and detrimental effects need to be carefully balanced. As such, the purpose of this review is to provide a summary of the involvement of substance P in acute inflammation, particularly in the context of traumatic brain injury and stroke.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

It is unclear how important it is to reduce fluoroquinolone consumption in the general population to prevent the spread of fluoroquinolone resistance in Neisseria gonorrhoeae (bystander selection). Methods We assessed bystander selection by using Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in N. gonorrhoeae was correlated with the prevalence of fluoroquinolone resistance in four other gram-negative species - Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa. Results Fluoroquinolone resistance in N. gonorrhoeae was positively associated with homologous resistance in all 4 species - A. baumanii. (ρ=0.61, P=0.0003, E. coli (ρ=0.67, P<0.0001), K. pneumoniae (ρ=0.52, P=0.0004) and P. aeruginosa (ρ=0.40, P=0.0206). Positive associations were also found between the national prevalence of fluoroquinolone resistance and fluoroquinolone consumption in the general population in the preceding year for 4 of the 5 species. Conclusions Gonococcal fluoroquinolone resistance can be productively viewed as being part of a syndemic of fluoroquinolone resistance. Strengthening antimicrobial stewardship programs may help retard the spread of fluoroquinolone resistance in N. gonorrhoeae.

Dendrobium okinawense is an endangered epiphytic orchid, and there has been no scientific report so far on its propagation. Protocorm is mass of cell, and protocorm-like bodies (PLBs) look alike protocorm produced by vegetative explants in vitro. Regeneration of PLBs is the most efficient technique for the orchids micro-propagation. We used different light emitting diodes (LEDs) for the efficient PLB organogenesis of D. okinawense. PLBs regenartion under green and red LED surpassed respectively 81.1% and 71.6% in numbers, and respectively 80.8% and 57.8% in fresh weight over white fluorescent light. We manipulated the culture media by different concentrations of PCIB and HMI. PLBs organogenesis promoted by low concentration, it increased respectively 35.9% and 19.3% over control by 0.01 mg/L PCIB and 0.01 ml/L HMI in numbers. Green LED and PCIB independently produced mostly similar numbers of new PLBs. Interestingly, culture media with 0.01 mg/L of PCIB further increased 8.5% of the numbers of PLBs under green LED, whereas the culture media with 0.01 mg/L HMI reduced the number of PLBs under green LED. PLBs culture under green LED with very low concentrations of PCIB manipulated culture media can significantly increase their organogenesis of D. okinawense.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

We introduce a new generalized inverse (i.e., generalized EP element) which is a natural generalization of EP and *-DMP elements in a Banach *-algebra. We present polar-like characterizations of generalized EP elements. The necessary and sufficient conditions under which the sum of two generalized EP elements is a generalized EP element are investigated. Finally, the generalized core-EP orders for generalized EP elements are characterized.

This comprehensive review explores the advancements in Orthognathic and Oral Maxillofacial Surgery, focusing on the integration of 3D Printing and Virtual Surgical Planning (VSP). Traditional surgical methods, while effective, come with inherent risks and complications, and can lead to variability in outcomes due to the reliance on the surgeon's skill and experience. The shift towards patient-centric care necessitates personalized surgical methods, which can be achieved through advanced technology. The amalgamation of 3D printing and VSP revolutionizes surgical planning and implementation by providing tactile 3D models for visualization and planning, and accurately designed surgical guides for execution. This convergence of digital planning and physical modeling facilitates a more predictable, personalized, and precise surgical process. However, the adoption of these technologies presents challenges, including the need for extensive software training and the steep learning curve associated with computer-aided design programs. Despite these challenges, the integration of 3D printing and VSP paves the way for advanced patient care in orthognathic and oral maxillofacial surgery.

HIV diagnosis and management have often caused disruptions to the everyday life and imagined futures of people living with HIV, both at individual and social levels. This has been conceptualised, in a rather dystopian way, as ‘biographical disruption’. This paper attempts to re-cast data from interviews with 40 men living with HIV (MLHIV) in Yogyakarta and Belu, Indonesia, in a slightly more positive light. Our analysis uses the concepts of additive and subtractive resilience strategies and we show how, rather than having a purely disrupted biography, participants talked about their experiences of ‘biographical reinvention'. Study participants were recruited using the snowball sampling technique, starting from two HIV clinics in the settings. Data were collected using one-on-one in-depth interviews, and a qualitative framework analysis was used to guide step-by-step data analysis. The findings showed that despite the disruptions in their everyday life (i.e., mental health condition, work, activities, social relationships, etc.) following the HIV diagnosis and management, MLHIV in our study managed to utilise their internal assets or traits (i.e., hope, optimism, resilience) and mobilised external resources (i.e., support from families, friends and healthcare professionals) to cope with the disruptions. An interweaving of these internal assets and external resources enabled them to take on new activities and roles (additive resilience strategies) and give up health compromising behaviours (subtractive resilience strategies). These were effective for most MLHIV in our study not only to cope with the HIV repercussions and improve their physical and mental health conditions, but to think or work on a ‘reinvented’ biography which encompassed resilience, hope and optimism for better health, life and future. The findings indicate the need for HIV interventions and healthcare systems that provide appropriate support for the development and maintenance of internal assets of PLHIV to enable them to cope with the repercussions of HIV and work on a ‘reinvented’ biography.

The performance of a small reconfigurable unmanned aerial vehicle (UAV) is evaluated, 1 combining a multidisciplinary approach in computational analysis of additive manufactured struc- 2 tures, fluid dynamics, and experiments. Reconfigurable UAVs promise cost savings and efficiency 3 without sacrificing performance, while demonstrating versatility to fulfill different military mission 4 profiles. The use of computational fluid dynamics (CFD) in UAV design produces higher accuracy 5 aerodynamic data, which is particularly important for complex aircraft concepts such as blended 6 wing bodies. To address challenges relating to anisotropic materials, the Tsai-Wu failure criterion is 7 applied to structural analysis, using CFD solutions as load inputs. Aerodynamic performance results 8 show the low-speed variant attains an endurance of 1 hour, 48 minutes, whereas for its high-speed 9 counterpart, it is 29 minutes at 66.7% higher cruise speed. Each variant serves different aspects of 10 small UAS deployment in combat, with low-speed envisioned for close surveillance, and high-speed 11 for incursions. Experimental and simulation results suggest room for design iteration, in wing area 12 and geometry adjustments. Structural simulations demonstrated the need for airframe improvements 13 in the low-speed configuration. This paper highlights the potential of reconfigurable UAVs to disrupt 14 the industry, advocating for further research and design improvements.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

Comparison of the influence of conditioning temperature of microspheres made of medical grade poly(L-lactide) (PLLA) and polylactide with 4wt.% of D-lactide content (PLA), on its thermal and structural properties is presented. The microspheres were fabricated by solid-in-oil-in-water method for application in additive manufacturing. The microspheres were annealed below glass transition temperature (Tg), above Tg but below onset of cold crystallization, and at two temperatures selected from the range of cold crystallization corresponding to crystallization of α’ and α form of poly(L-lactide) respectively, i.e., at 40°C, 70°C, 90°C and 120°C, in order to verify the influence of conditioning temperatures on sinterability of microspheres set as sintering window (SW). Based on differential scanning calorimetry measurements SW of microspheres were evaluated with consideration of existence of cold crystallization and reorganization of crystal polymorph. The results indicate that the conditioning temperature influence on availability and range of SW that depending on the D-lactide presence. We postulate the need for an individual approach for polylactide powders in determining the SW as a temperature range free of any thermal events. Moreover, other core powder characteristic, such as residual solvent content, morphology, particle size distribution, powder flowability and thermal conductivity, as a key property for successful laser sintering, are characterized. The microspheres are close to sphere and the size of microspheres are below 100 µm. Residual solvents content decreases with the increase of annealing temperature. The thermal conductivity is 0.073 W/mK and 0.064 W/mK for PLA and PLLA microspheres, respectively, and it depends on the spherical shape of the microspheres. Furthermore, the WAXD studies prove that an increase in the conditioning temperature causes a slight increase in crystallinity degree for PLLA microspheres and clear increase in crystallization for PLA microspheres.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

Recent algorithmic-based research in the stock market has predominantly focused on ultra-high-frequency trading and index estimation. We developed an improved algorithm to address the need for a low-frequency, real-world trading model to build on the existing high hit-ratio and low maximum drawdown. We utilized established price indicators, Stochastic and Williams %R, and introduced a volume factor to increase the model's safety to enhance the model's performance. This improved algorithm demonstrated superior returns while maintaining high hit-ratio and low maximum drawdown. Specifically, we leveraged the existing algorithm to trade using 2X and 3X signals, incorporating volume data, the 52-week average, standard deviation, and other factors. The data set comprised SPY ETF price and volume from 2010 to 2023, covering over 13 years. Our enhanced algorithmic trading model outperformed both the benchmark and previous results, achieving a hit rate of over 90%, a maximum drawdown of less than 1%, an average of 1.5 trades per year, a total return of +519.3%, and an annualized return (AnnR) of +15.1%. The analysis demonstrates that the model's simplicity, ease of application, and comprehensibility can assist investors in making informed investment decisions albeit the past performance does not guarantee future returns.

The aim of this work was to investigate a new, simple one-pot combustion synthesis technique for creating sulphur-based CuS/ZnS p-n heterojunction nanocomposite photocatalysts. The study examined the photocatalytic activity and reusability of these nanocomposites in removing rhodamine B (RhB) dye under visible light irradiation. Various methods of characterisation were employed to determine the properties of the materials, including particle morphology, crystalline phases and bandgap energy. The intrinsic reaction parameters, such as catalyst loading, pH level of the solution, and initial pollutant concentration, were varied to establish the optimal photo-degradation conditions. The results showed that a binary CuS/ZnS catalyst with a 10 gL-1 loading, at pH 5, degraded 97% of 5 ppm RhB dye after 270 minutes of visible light irradiation. Addition-ally, this composite catalyst exhibited excellent chemical stability and reusability, achieving 83% RhB dye removal after five recycling runs. Scavenger tests identified the photogenerated holes (h+) and superoxide free radicals (•O2) as the primary reactive species responsible for degradation. This study provides valuable insight into the design of highly efficient nanomaterials for removing organopollutants in wastewater, and a possible reaction mechanism is proposed.

In many practical applications, it is more convenient to characterize the quality of production processes or service operations throughout the count of nonconformities. In the context of SPC, nonconformities are usually assumed to appear according to the binomial probability model. The conventional way for monitoring nonconformities involves Shewhart-type control procedures based on both constant and time-varying sample sizes. In this article, an EWMA scheme is proposed for monitoring the fraction of nonconforming items with time-varying sample sizes. The proposed control chart is referred to as the EWMAG-B and can be easily adapted to work with a constant sample size by fixing it at a needed value. By means of simulation, it was found out that the EWMAG-B chart outperforms the conventional p control chart in Phase II while detecting changes in the process level is wanted.

The thermoelectric generator (TEG) stands out in many energy harvesters due to its simple structure, small size, etc. However, previous studies rarely probe into the influence of TEG internal resistances on extracting maximum power from TEG, and tracking efficiency is limited. By analyzing the relationship between the tracking efficiency and the TEG internal resistances, a time exponential rate perturbation and observation (P&amp;O) technology is proposed to achieve maximum power point tracking (MPPT) for a wide resistance range of TEG. Using the time exponential rate P&amp;O, the MPPT circuit observes the power change by comparing PMOS on-time and perturbs the power by adjusting NMOS on-time exponentially. The MPPT circuit is implemented in a 110nm CMOS process. The tracking efficiency keeps a high level from 98.9 to 99.5%. The applicable range of the TEG resistance is from 1 to 12Ω, which is enhanced at least 2.2 times.

The cellular stress response corresponds to the molecular changes that cell undergoes in response to various environmental stimuli. It induces drastic changes in the regulation of gene expression, at transcriptional and post-transcriptional levels. Actually, translation is strongly affected with a blockade of the classical cap-dependent mechanism, whereas alternative mechanisms are activated to support translation of specific mRNAs. One of the major mechanisms involved in stress-activated translation is the internal ribosome entry site (IRES)-driven initiation. IRESs, first discovered in viral mRNAs, are present in cellular mRNAs coding for master regulators of cell responses, whose expression must be tightly controlled. IRESs allow translation of these mRNAs in response to different stresses, including DNA damage, amino-acid starvation, hypoxia or endoplasmic reticulum stress, as well as to physiological stimuli such as cell differentiation or synapse network formation. Importantly, cellular mRNA IRESs are regulated by IRES trans-acting factor (ITAFs), exerting their action by at least nine different mechanisms. This review presents an update of the reported ITAFs regulating cellular mRNA translation and of the different mechanisms allowing them to control translation initiation in specific conditions. The impact of ITAFs on coordinated expression of mRNA families and consequences in cell physiology and diseases are also highlighted.

P-glycoprotein (P-gp), a membrane-bound transporter, can eliminate xenobiotics by transporting them out of the cells or blood-brain barrier (BBB) at the expense of ATP hydrolysis. Thus, P-gp mediated efflux plays a pivotal role in altering the absorption and disposition of a wide range of substrates. Nevertheless, the mechanism of P-gp substrate efflux is rather complex since it can take place through active transport and passive permeability in addition to multiple P-gp substrate binding sites. A nonlinear quantitative structure-activity relationship (QSAR) model was developed in this study using the novel machine learning-based hierarchical support vector regression (HSVR) scheme to explore the perplexing relationships between descriptors and efflux ratio. The predictions by HSVR were found to be in good agreement with the observed values for the molecules in the training set (n = 50, r² = 0.96, q²_CV = 0.94, RMSE = 0.10, s = 0.10) and test set (n = 13, q² = 0.80–0.87, RMSE = 0.21, s = 0.22). When subjected to a variety of statistical validations, the developed HSVR model consistently met the most stringent criteria. A mock test also asserted the predictivity of HSVR. Consequently, this HSVR model can be adopted to facilitate drug discovery and development.

Predicting heart disease is crucial for early diagnosis and intervention, significantly improving patient outcomes and reducing mortality rates. This study compares various machine learning models, including Logistic Regression, Random Forest, Gradient Boosting, XGBoost, and Long Short-Term Memory (LSTM) networks, using the Cleveland Heart Disease dataset. Comprehensive preprocessing steps were undertaken, such as handling missing values, converting categorical variables to numeric forms, and binarizing the target variable for binary classification. Each model was rigorously evaluated using performance metrics, including accuracy, precision, recall, F1-score, and the area under the receiver operating characteristic curve (AUC-ROC). SHapley Additive exPlanations (SHAP) values were employed to provide insights into feature importance, ensuring model transparency and interpretability. The results indicate that XGBoost outperformed all other models, achieving an accuracy of 90% and an AUC-ROC of 0.94, demonstrating its superior ability to capture complex patterns in the data through advanced optimization techniques and regularization. This study highlights the significant potential of advanced machine learning techniques, particularly ensemble methods like Gradient Boosting and XGBoost, in enhancing heart disease prediction. These models offer higher accuracy and valuable interpretability, making them practical tools for early diagnosis in clinical settings. Future research should focus on integrating these models into healthcare systems and exploring hybrid approaches to further improve predictive performance and clinical applicability.

The manuscript presents the use of three novel technologies for the implementation of wireless green battery-less sensors that can be used in agriculture. The three technologies, namely additive manufacturing, energy harvesting, and wireless power transfer from airborne transmitters carried from UAVs, are considered for smart agriculture applications. Additive manufacturing is exploited for the implementation of both RFID based sensors and passive sensors based on humidity sensitive materials. A number of energy-harvesting systems at UHF and ISM frequencies are presented which are in position to power platforms of wireless sensors, including humidity and temperature IC sensors used as agriculture sensors. Finally, in order to provide the wireless energy to the soil-based sensors with energy harvesting features, wireless power transfer (WPT) from UAV carried transmitters is utilized. The use of these novel technologies can facilitate the extensive use and exploitation of battery-less wireless sensors which are environmentally friendly and thus “green”. Additionally, it can potentially drive precision agriculture in the next era, through the implementation of a vast network of wireless green sensors which can collect and communicate data, to airborne readers so as to support with data the Artificial Intelligence and Machine Learning based, decision making platforms.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

We explore 3D printing modules for self-assembling spacecraft and robots – structure, actuators, electrics. Self-assembly has long been viewed as a highly desirable capability for autonomous construction of large space structures. We review self-assembly in space which focusses on the self-assembly of modules that demonstrate the range of applications. However, self-assembly may be synergised with 3D printing to offer an automated capability from raw material to modules for assembling new spacecraft or habitats. One application of 3D printing is using space debris on-orbit as an in-situ resource - defunct spacecraft may be salvaged as raw material for in-situ construction on demand. The common features of all self-assembling modules are that the modules constitute a structure housing a computer-controlled actuator internally and a reversible latching mechanism externally. We have demonstrated a 3D printed DC electric motor in which the only components that were not 3D printed are the wire coils. We have married our 3D printed motor prototype as an actuated joint between two 3D printed trigon-type panels developed as part of a trigon self-assembling system concept. The trigon concept underlies a modular approach to self-assembling and self-deploying structures. The 3D printed motorised panel system demonstrates that the motor aspect and structural aspects of robotic self-assembling machines are amenable to 3D printing. This has implications for self-assembling systems into modular satellites as a solution to space debris.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.