A power amplifiers are crucial components that significantly influence the linearity and energy efficiency of next-generation communication system radio units. A key challenge in designing power amplifiers is managing high Peak-to-Average Power Ratio (PAPR) to achieve both high linearity and energy efficiency during back-off conditions. This paper presents simulation and measurement results for a dynamic load modulation power amplifier based on a ferroelectric tunable matching network. Experimental studies on the power amplifier with the tunable output matching network confirm its performance at 8 dB back-off while varying the control voltage applied to the ferroelectric element. Additionally, a bias modulator to adjust the transistor's load in relation to input power was designed. Measurement studies of the dynamic load modulation power amplifier demonstrated an efficiency of at least 50% at 8 dB back-off and higher 60% at peak power. Furthermore, it was found that the modulator output voltage adjustment function on input power of the bias modulator affects the linearity of the output power. Different bias responses are studied and, as a result, optimal output voltage response is found. The proposed load modulation power amplifier is promising for operation with high PAPR digital signals.

This paper proposes the impact of plug-in electric vehicles integrated into power distribution system based on voltage dependent control. The plug-in electric vehicles was modeled as the static load model in power distribution systems under balanced load condition. The power flow analysis is determined by using the basic parameters of the electrical network. The main point of this study are compare with voltage magnitude profiles, load voltage deviation, and total power losses of the electrical power system. There are investigating the affected from constant power load, constant current load, constant impedance load and plug-in electric vehicles load, respectively. The IEEE 33 bus test system is used to test the proposed method by assigning each load type to a balanced load in steady state and applied the solving methodology based on the bus injection to branch injection matric, branch current to bus voltage matrix, and current injection matrix to solve the power flow problem. The simulation results showed that the plug-in electric vehicles load had the lowest impact compared to other loads. The lowest plug-in values for the electric vehicle loads were 0.062, 119.67 kW and 79.31 kVar for the load voltage deviation, total active power loss and total reactive power loss, respectively. Therefore, this study can be verified that the plug-in electric vehicles load were affected to the lowest of the electrical power system in condition to same sizing and position. So that, in condition to the plug-in electric vehicles load added into the electrical power system with the conventional load type or complex load type could be considered that the affected from the plug-in electric vehicles load in next study.

Background: The prevalence of human T-lymphotropic virus type-1 (HTLV-1) infection is higher in women, and sexual intercourse has been described as an important route of male-to-female transmission. The present study aimed to quantify HTLV-1 proviral load (PVL) in vaginal fluid, and to investigate correlations with PVL in peripheral blood mononuclear cells (PBMC). Methods: HTLV-1-infected women were consecutively recruited at a multidisciplinary center for HTLV patients in Salvador-Brazil. All women underwent gynecological examinations to obtain cervicovaginal fluid and venipuncture for blood collection. PVL, as measured by real-time quantitative polymerase chain reaction (RT-qPCR), was expressed as the number of copies of HTLV-1/106 cells in blood and vaginal fluid samples. Light microscopy was used to assess cervicovaginal cytopathology and vaginal microbiota. Results: In the 56 included women (43 asymptomatic carriers and 13 diagnosed with HTLV-associated myelopathy/tropical spastic paraparesis-HAM/TSP), mean age was 35.9 (SD±7.2) years. PVL was higher in PBMCs [median: 23,264 copies/106 cells (IQR: 7,420 - 64,371)] than in vaginal fluid [451.9 copies/106 cells (IQR: 0 - 2,672)] (p<0.0001). PVL in PBMCs was observed to correlate directly with PVL in vaginal fluid (R=0.32, p=0.01). PVL was undetectable in vaginal fluid samples from 20 women (35.7%), most of whom were asymptomatic (19/20). Cytopathologic analyses revealed no differences between women with detectable or undetectable PVL. Conclusion: HTLV-1 proviral load is detectable in vaginal fluid and correlates directly with proviral load in peripheral blood. This finding suggests that sexual transmission of HTLV-1 from female to male may occur and vertical transmission, particularly in the context of vaginal delivery.

The paper introduces an approach to extract information from measurements and generate new load cycles for electrical energy storage systems. Load cycle analysis is performed using rainflow counting, which helps evaluate data and identify stress factors. Load cycle generation can involve clustering methods, random micro-trip methods, and machine learning techniques. The study utilises the Random Pulse Method (RPM) and presents an improved version called the Gradient Random Pulse Method (gradRPM) that allows control over stress factors such as the gradient of the State of Charge (SOC). Another method called Information Maximizing-Recurrent Conditional Generative Adversarial Network (Info-RCGAN) has been developed, and it utilises a deep learning algorithm for data-driven load profile generation with control over stress factors. The results demonstrate the effectiveness of the gradRPM and Info-RCGAN methods in generating load profiles based on the given parameters. The findings provide valuable insights into designing simulation data or testing data for electrical energy storage applications, aiding in improving and understanding system behaviour and requirements.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

Understanding the shoulder-specific load in handball is important for both prevention and rehabilitation of shoulder injuries. The shoulder-specific load is largely a result of the number and speed of throws. However, it is difficult to quantify number and speed of throws in handball due to limitations in the current technology. Therefore, the purpose of this study was to develop a novel method to estimate throwing speed in handball using a low-cost accelerometer-based device. Nineteen experienced handball players each performed 25 throws of varying types while we measured the acceleration of the wrist using the accelerometer and the throwing speed using 3D motion capture. Using cross-validation, we developed four prediction models using combinations of the logarithm of the peak total acceleration, sex and throwing type as the predictor and the throwing speed as the outcome. We found that all models were well-calibrated (mean calibration of all models: 0.0 m/s, calibration slope range: 0.99-1.00) and precise (R2 = 0.71-0.85, mean absolute error = 1.32-1.82 m/s). We conclude that the developed method appear to provide practitioners and researchers with a feasible and cheap method to estimate throwing speeds in handball.

Non-intrusive load monitoring (NILM) is a core technology for demand response (DR) and energy conservation services. Traditional NILM methods are rarely combined with practical applications, and most studies aim to decompose the whole loads in a household, which leads to low identification accuracy. In this paper, an NILM approach based on multi-feature integrated classification (MFIC) is explored, which combines some non-electrical features such as ON/OFF duration, usage frequency of appliances, and usage period to improve load differentiability. The implementation of MFIC algorithm is consistent with traditional event-based method. The uniqueness of our algorithm is that it designs an event detector based on steady-state segmentation and a linear discriminant classifier group based on multi-feature global similarity. Simulation results using an open-access dataset demonstrate the effectiveness and high accuracy of MFIC algorithm, with the state-of-the-art NILM methods as benchmarks.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

The integration of advanced nuclear technologies like the System-Integrated Modular Advanced Reactor (SMART) into developing power grids presents unique opportunities for grid reliability. This network, connected to geothermal, hydro, solar, and wind power sources, comprises 220kV and 132kV transmission lines feeding 66kV, 33kV, and 11kV distribution lines to various load centers. As Kenya expands electricity access, maintaining grid stability while integrating new technologies becomes crucial for economic growth. While previous research has examined grid stability with renewable integration, the effects of advanced nuclear technologies in developing grids remain understudied. The study employs ETAP 22 simulation software to model three scenarios: a base case, compensator-only operation, and SMART-SMR integration. The analysis includes steady-state stability and reliability metrics such as SAIFI, SAIDI, CAIDI, and EENS. Results demonstrate significant improvements with SMART integration: SAIDI reduced by 2.8% to 5.0433 hours/customer-year, SAIFI improved by 5.1% to 0.0516 interruptions/customer-year, and voltage profiles stabilized between 98.21% and 98.91% of nominal. These findings highlight SMART potential to enhance grid performance in developing power systems, offering insights for policymakers towards achieving more reliable and clean energy infrastructure.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

Upon inbreeding, the architecture of the inbreeding load shifts as selection purges strongly deleterious recessive mutations and drift fixes many milder ones. Most small inbred populations show limited genetic variation while crosses between such populations commonly express pronounced heterosis, confirming fixation. In contrast, purging appears to be limited in that inbred populations often retain substantial inbreeding depression. In addition we have the enigma Darwin noted: purely selfing taxa are unknown. Because both purging and fixation reduce inbreeding depression and load, another mechanism must exist to sustain these. Background selection and the associations that develop among alleles in small inbred populations will shift the architecture of the load potentially creating blocks of recessive mutations linked in repulsion. This would generate pseudo-overdominance that could sustain these “PODs” and inbreeding load. Recombination and crosses between lineages could erode PODs. Crosses between populations fixed for different mutations would generate high pseudo-overdominance, enhancing heterosis and potentially POD formation. New recessive mutations arising within PODs would reinforce overdominance. PODs should generate clear genetic signatures including genomic hotspots of heterozygosity and linkage disequilibrium containing alleles at intermediate frequency generating segregating load. Results from several simulation and empirical studies match these predictions. Further simulations and comparative genomic analyses are needed to rigorously test whether PODs exist in sufficient strength and number to generate persistent inbreeding depression and load in inbred lineages.

The background of this work is related to the scheduling of household appliances, taking into account variations in energy costs during the day, due to official Brazilian domestic tariffs: constant and white. The white tariff can reach an average price of around 17\% lower than the constant, but charges twice its value at peak hours. In addition to cost reduction, we propose a methodology to reduce user discomfort due to time shifting of controllable devices, presenting a balanced solution through the analytical analysis of a new method here called tariff space, derived from white tariff posts. To achieve this goal, we explore the geometric properties of the movement of devices through the tariff space (geometric locus of the load), over which we can define a limited region in which the cost of a load under the white tariff will be equal to or less than the constant tariff. As a trial for the efficiency of this new methodology, we collected some benchmarks (such as execution time and memory usage) against a classic multi-objective algorithm (Hierarchical) available in the language portfolio in which the project has been executed (Julia language). As a result, both methodologies achieve similar results, but the one presented in this article shows a significant reduction in processing time and memory usage, which could lead to the future implementation of the solution in a simple, low-cost embedded system like an ARM cortex M.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

This paper reviews non-intrusive load monitoring (NILM) approaches that employ deep neural networks to disaggregate appliances from low frequency data, i.e. data with sampling rates lower than the AC base frequency. We first review the many degrees of freedom of these approaches, what has already been done in literature, and compile the main characteristics of the reviewed publications in an extensive overview table. The second part of the paper discusses selected aspects of the literature and corresponding research gaps. In particular, we do a performance comparison with respect to reported MAE and F$_1$-scores and observe different recurring elements in the best performing approaches, namely data sampling intervals below 10\,s, a large field of view, the usage of GAN losses, multi-task learning, and post-processing. Subsequently, multiple input features, multi-task learning and related research gaps are discussed, the need for comparative studies is highlighted, and finally, missing elements for a successful deployment of NILM approaches based on deep neural networks are pointed out. We conclude the review with an outlook on possible future scenarios.

Load balancing to alleviate network congestion remains a critical challenge in Vehicular Ad-Hoc Networks (VANETs). During route and response scheduling, RSUs risk being overloaded beyond their calculated capacity. Despite recent advancements like RSU-based load transfer, NP-Hard hierarchical geography routing, RSU-based MAC schemes, simplified clustering, and network activity control, a significant gap persists in employing a load-balancing server for effective traffic management. We propose a server-based network congestion handling mechanism (SBNC) in VANETs to bridge this gap. Our approach clusters RSUs within specified ranges and incorporates dedicated load balancing and network scheduler RSUs to manage route selection and request-response scheduling, thereby balancing RSU loads. We introduce three key algorithms: optimal placement of dedicated RSUs, a scheduling policy for packets/data/requests/responses, and a congestion control algorithm for load balancing. Using the VanetMobiSim library of Network Simulator-2 (NS-2), we evaluate our approach based on residual energy consumption, end-to-end delay, packet delivery ratio (PDR), and control packet overhead. Results indicate substantial improvements in load balancing through our proposed server-based approach.

As the most important component of soft robot, the pneumatic actuator can drive robot movement. However, the effect of the actuator pneumatic network geometry on the actuator load capacity is insufficient. In this paper, the finite element analysis method is applied to calculate the load force and stability torque of the pneumatic actuator under a wide range of length and height dimensions of the pneumatic network. The effect of the network size on the structure rigidity, load capacity and deformation of the actuator is analyzed. Based on the calculation results, the effect of network structure size on the deformation and load capacity is analyzed, and the optimal geometric results with the maximum load capacity are obtained. This study provides theoretical guidance for the structural design and optimization of the pneumatic actuator.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

This research presents a novel Customised Load Adaptive Framework (CLAF) for fault classifica-tion in Induction Motors (IMs), utilizing the Machinery Fault Prevention Technology (MFPT) Bearing Dataset. CLAF represents a pioneering approach that extends traditional fault classification methodologies by accounting for load variations and dataset customization. Through a meticulous two-phase process, it unveils load-dependent fault subclasses that have not been readily identified in traditional approaches. Additionally, new classes are created to accommodate the dataset's unique characteristics. Phase 1 involves the exploration of load-dependent patterns in time and frequency domain features using one-way Analysis of Variance (ANOVA) ranking and validation via bagged tree classifiers. In Phase 2, CLAF is applied to identify mild, moderate, and severe load-dependent fault subclasses through optimal Continuous Wavelet Transform (CWT) selection through Wavelet Singular Entropy (WSE) and CWT energy analysis. The results are compelling, with a 96.3% classification accuracy achieved when employing a wide neural network to classify proposed load-dependent fault subclasses. This underscores the practical value of CLAF in en-hancing fault diagnosis in IMs and its future potential in advancing IM condition monitoring.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Feline coronavirus (FeCoV) causes enteric disease in cat worldwide. In general, FeCoV infection is characterized by self- limiting gastroenteritis but not understood changes can give rise to mutants that lead to the development of feline infectious peritonitis (FIP). In cats, FeCoV replicates in the intestines and spreads by fecal-oral transmission and persists in multi-cats households by infec-tion and re-infection by the same or another viral strain. Although current evidence shows that probiotics have promise for enhancing health benefits protecting from viral infection, today there are no studies regarding the use of probiotics in reducing fecal emission of feline coronavirus in naturally infected cats. The aim of the present study was to evaluate the effect of specific mul-ti-strain probiotics on FeCoV viral load in 25 naturally-infected cats. The study population con-sisted of purebred Birmanian cats, of which 14 females and 11 males, aged from1 to 4 years, and positive for FeCov by Real-time PCR on fecal sample. Two microcaps of probiotic formulation containing billion bacteria were administered to all cat once a day for 60 consecutive days. After probiotic administration, clinical conditions and FeCov viral load was assessed by Real-time PCR on fecal samples. All animals did not present alteration in the clinical condition at T1 (after probiotic administration); seventeen out of 25 cats tested negative at the end of the study, while the remaining 8 cats tested positive at the end of the study. The results of the present study suggest that high concentrations of live probiotics supplementation are well-tolerated and may poten-tially reduce the fecal FeCoV viral load.

VHF Data Exchange System (VDES) is considered as an important component of the future maritime communication system by the International Maritime Organization (IMO). On the basis of existing Automatic Identification System (AIS), VDES adds the other two higher capacity subsystems: Application Specific Message (ASM) and VHF Data Exchange (VDE). The Random Access Channel (RACH) of VDE was first introduced in the International Telecommunication Union (ITU) Recommendation M.2092-0. As the slot planning of RACH in VDE is interval, which is significantly different from the continuous slot map for access algorithms in AIS, the existing slot access algorithms cannot meet the requirements of VDE. The simulation results show that the VDE slot map can reduce the normalized throughput of the existing algorithm by 39%. A novel random access algorithm called Adaptive Traffic Load Contention Resolution Diversity Slotted ALOHA (ATL-CRDSA) is proposed in this paper. The algorithm combines the load control strategy and contention resolution scheme to overcome the challenges of the new RACH of VDE. Simulation results show that ATL-CRDSA has remarkable improvement on RACH, and makes RACH very efficient and provides low latency of the packets. The insights gained from this study may be of assistance to the Media Access Control (MAC) layer design for upcoming versions of VDES standard.

We provide a comprehensive framework for forecasting five minute load using Gaussian processes with a positive definite kernel specifically designed for load forecasts. Gaussian processes are probabilistic, enabling us to draw samples from a posterior distribution and provide rigorous uncertainty estimates to complement the point forecast, an important benefit for forecast consumers. As part of the modeling process, we discuss various methods for dimension reduction and explore their use in effectively incorporating weather data to the load forecast. We provide guidance for every step of the modeling process, from model construction through optimization and model combination. We provide results on data from the PJMISO for various periods in 2018. The process is transparent, mathematically motivated, and reproducible. The resulting model provides a probability density of five-minute forecasts for 24 hours.

To satisfy the interests of multiple agents and those of comprehensive indicators such as peak-to-valley differences and load fluctuations occurring on the network side, this paper presents a flexible load demand-side response optimization method that considers the benefits of peak-to-valley smoothing. First, load aggregation modelling of air conditioning and electric vehicles was conducted, and the complementarity of the power consumption behaviour of different types of flexible loads was used to improve the responsiveness of the load aggregator. Second, considering demand-side responses and taking into account the interests of both supply and demand, the load fluctuation and peak-to-valley difference on the network side are reduced, and a flexible load double-layer optimization model incorporating the peak-to-valley smoothing benefit is established. Finally, the effectiveness of the proposed optimization model is verified by using the KKT condition and the big M method to evaluate this two-layer optimization problem as a single-layer optimization problem. Comparative examples demonstrate that the proposed two-layer optimization method can improve the revenue of the distribution network operators and the load aggregators by using the complementary nature of the load response characteristics of electric vehicles and air conditioners. Moreover, the proposed method can effectively reduce the load peak-to-valley difference and load fluctuation of the distribution network by introducing the peak-to-valley smoothing benefit model.

The sustainability of cities often changes as rapid urban developments and population growth affect the carrying capacity. Understanding the dynamics of carrying capacity then becomes crucial for tourist-oriented cities. This study focused on Baguio City, the "Summer Capital of the Philippines," attracting large crowds on holidays and actively promoting various events on non-holidays, thereby having temporal context variations classified as regular days, days with events, and holidays. Using the enhanced urban carrying capacity load number (EUCCLN) model, load number (LN) changes for different temporal contexts are calculated based on spatial indicators grouped into air, traffic, economy, and waste. The city experiences the worst pressures on air quality during holidays with $99.23\%$ districts under very high to critical levels followed by regular and days with events. However, the total LN is balanced by favorable economic conditions with only $9.23\%$ at critical. EUCCLN effectively pinpoints areas experiencing critical states at any time, advocating targeted government monitoring. We demonstrate that Night Time Light, for places with no economic data available, can be used as a proxy to highlight areas requiring improved urban vibrancy. This work suggests that EUCCLN monitoring urban pressures can easily be expanded to nowcasting with real-time data.

For many years, energy monitoring at the most disaggregate level has been mainly sought through the idea of Non-Intrusive Load Monitoring (NILM). Nevertheless, a practical application of this concept in the residential sector should address the underlying concerns raised by the technical specifications of case studies. From one side, such an operation must handle common matters related to the essence of any NILM system. Although this aspect has been thoroughly investigated by basic research, it is limited to the properties of public datasets. On the other side, it must deal with specific concerns corresponding to uncommon situations. These circumstances impose further restrictions on existent NILM schemes, however, they have been overlooked due to the lack of pertinent databases to scrutinize. Accordingly, this paper presents applied research on a potential solution to NILM for Quebec residences. It carries out a relevant investigation into the multi-faceted nature of this problem in order to reveal barriers to feasible implementations in the context of Quebec. This work commences with a concise discussion about the NILM idea to highlight its essential requirements for a fruitful practice. Afterward, it provides a comparative statistical analysis to represent the specificity and potential challenges of the case study in accordance with NILM necessities. For this purpose, the examination exploits data from real-world measurement systems in the same and European regions. Subsequently, this study focuses on a load identification exercise by proposing a combinatory approach that utilizes the promise of sub-meter smart technologies to integrate the intrusive aspect of load monitoring with the non-intrusive one. The former is aimed at extracting overall heating demand from the aggregate one by a supervised procedure based on Deep Learning (DL) models while the latter is designed for disaggregating the residual load through an unsupervised process on the basis of clustering techniques. The results demonstrate that geographically-dependent cases create electricity consumption scenarios under which existing NILM methods can be questioned. From a realistic standpoint, this research elaborates on critical remarks to realize viable NILM systems, particularly, in Quebec houses.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

The primary aim of this study was to investigate the variations in cognitive load as self-efficacy gradually increases and examine the potential within-mediating effect of state anxiety between self-efficacy and cognitive load. The experiment manipulated the self-efficacy of 49 adult participants through the false feedback paradigm, employing a within-subject experimental design and using facial expression recognition as the experimental task. The data were analyzed using Hierarchical Linear Modeling. The results revealed that self-efficacy negatively predicted state anxiety and cognitive load, while state anxiety positively predicted cognitive load. Moreover, state anxiety played a complete mediating role at multiple levels in this process.

(1) Background: The purpose of this study was to assess the external load demands in futsal, con-sidering both home and away matches and their outcomes, in order to plan microcycles throughout the season based on the external load of each match. (2) Methods: The external load of 10 players from a First Division team in the Spanish Futsal League was recorded. The total dura-tion of player involvement with the clock stopped was 18.15 ±7.04 minutes. The players' external load was monitored using OLIVER devices. To analyse the influence of the match outcome and location on the external load, a univariate general linear model (GLM) analysis was conducted. (3) Results: There are no differences between the variables, except for accelerations of 2 to 3 m/s² (m) per minute and the number of accelerations of 2 to 3 m/s² per minute. Despite not showing significant differences, there is a trend indicating a higher demand for external loads in away matches as well as in matches won. (4) Conclusions: These findings are important for planning microcycles and providing the appropriate dosage to each player to achieve optimal performance in matches.

Recently, the application of Artificial Intelligence (AI) in many areas of life has allowed raising the efficiency of systems and converting them into smart ones, especially in the field of energy. Integrating AI with power systems allows electrical grids to be smart enough to predict the future load, which is known as Intelligent Load Forecasting (ILF). Hence, suitable decisions for power system planning and operation procedures can be taken accordingly. Moreover, ILF can play a vital role in electrical demand response, which guarantees a reliable transitioning of power systems. This paper introduces a Perfect Load Forecasting Strategy (PLFS) for predicting future load in smart electrical grids based on AI techniques. The proposed PLFS consists of two sequential phases, which are; Data Preprocessing Phase (DPP) and Load Forecasting Phase (LFP). In the former phase, input electrical load dataset is prepared before the actual forecasting takes place through two essential tasks, namely feature selection and outlier rejection. Feature selec-tion is done using Advanced Leopard Seal Optimization (ALSO) as a new natural inspired opti-mization technique, Citation: To be added by editorial staff during production. Academic Editor: Firstname Last-name Received: date Revised: date Accepted: date Published: date Copyright: © 2023 by the authors. Submitted for possible open access publication under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/). While outlier rejection is accomplished through Interquartile Range (IQR) as a measure of statis-tical dispersion. On the other hand, actual load forecasting takes place in LFP using a new pre-dictor called; Weighted K-Nearest Neighbor (WKNN) algorithm. The proposed PLFS has been tested through excessive experiments. Results have shown that PLFS outperforms recent load forecasting techniques as it introduces the maximum prediction accuracy with the minimum root mean square error.

The objective was to compare the failure loads of glass ceramic, and polymer crowns against yttria-partially stabilized zirconia (Y-PSZ) crowns with varying yttria concentrations. Monolithic crowns of zirconia (Cercon XT, Katana UTML, BruxZir Anterior), glass ceramic (Celtra press, IPS e.max press, Lisi press), and polymeric materials (Trilor, Juvora, Pekkton) were fabricated and cemented to epoxy abutments. The total number of specimens was 135 for crowns and 135 for discs (15 specimens per material type and design). A universal testing machine was used to perform compressive loading of all crowns to failure with a steel hemisphere along the longitudinal axis of the abutments. Energy dispersive spectroscopy (EDS) was used to identify the concentration (mol% yttria-partially stabilized zirconia) for each zirconia brand. The data were analyzed using a generalized linear model and regression analysis. The results revealed significant differences (P < .05) in mean failure loads for different crown materials: Trilor (6811 ± 960 N) > Juvora (5215 ± 151 N) > Cercon (4260 ± 520 N) = BruxZir (4186 ± 269 N) = e.max (3981 ± 384 N) > Katana (3195 ± 350 N) = Lisi (3173 ± 234 N) = Pekkton (3105 ± 398 N) > Celtra (2696 ± 393 N). EDS showed that the zirconia materials contained yttria at different concentrations (BruxZir = 5Y-PSZ, Cercon = 4Y-PSZ, Katana = 3Y-PSZ). The yttria concentration had a significant effect on the failure load of the Katana (3Y-PSZ) crowns, which revealed lower failure loads than the Cercon (4Y-PSZ) and BruxZir (5Y-PSZ) crowns. New zirconia materials are provided with different yttria concentrations (3Y-, 4Y-, and 5Y-PSZ). Since a higher yttria concentration increases the translucency, clinicians should be aware that 4-5 wt% yttria-partially stabilized zirconia materials provide comparable or higher mechanical properties than e. max glass ceramic for dental application of crowns.

In view of the floating rectangular aerostatic guideway problem of low load capacity and stiffness, this paper puts forward a kind of closed rectangular aerostatic guideway and its optimized design. Firstly, the analytic calculation formula of a closed rectangular aerostatic guideway was deduced. The use of MATLAB software for the numerical simulation and the parameter influence analyses was carried out in terms of the gas supply pressure on load capacity and stiffness. A simulation model of the rectangular air bearing was also built using the Fluent software, and the model was used for simulation calculations. Secondly, the static performance of the rectangular air bearing was analyzed by analyzing the distribution position and number of orifices on its load capacity and stiffness. On this basis, the response surface optimization design method is used to analyze the variation law of the load capacity and stiffness of the air bearing under different restrictor structural parameters. Finally, the optimal design parameters for the rectangular air bearing are obtained. The simulation results show that the optimized rectangular air bearing designed in this paper has a good load capacity and stiffness of 644.58N and 63.405N N∙μm^(-1).

The purpose of this study was to compare Electromyographic (EMG) with Mechanomyo- 1 graphic (MMG) recordings during isometric conditions, and during a simulated load-lifting task. 2 Twenty-two males (age: 25.5 ± 5.3 years) first performed maximal voluntary contractions (MVC) and 3 submaximal isometric contractions of upper limb muscles at 25%, 50% and 75% MVC. Participants 4 then executed repetitions of a functional activity simulating a load-lifting task above shoulder level, 5 at 25%, 50% and 75% of their maximum activity (based on MVC). The low frequency part of the 6 accelerometer signal (< 5 Hz) was used to segment the 6 phases of the motion. EMG and MMG were 7 both recorded during the entire experimental procedure. Root mean square (RMS) and mean power 8 frequency (MPF) were selected as signal extraction features. During isometric contractions, EMG 9 and MMG exhibited similar repeatability scores. They also shared similar RMS vs force relationship, 10 with RMS increasing to 75% MVC and plateaued to 100%. MPF decreased with increasing force to 11 75% MVC. In dynamic condition, RMSMMG exhibited higher sensitivity to changes in load than 12 RMSEMG. These results confirm the feasibility of MMG measurements to be used during functional 13 activities outside the laboratory. It opens new perspectives for future applications in sports science, 14 ergonomics and human-machine interfaces conception.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

White Spot Syndrome Virus (WSSV) has emerged as one of the most prevalent and lethal viruses globally, and infects both shrimps and crabs in the aquatic environment. This study aimed to investigate the occurrence of WSSV in different ghers of Bangladesh and the virulence of the circulating phylotypes. We collected 360 shrimp (Penaeus monodon) and 120 crab (Scylla sp.) samples from the South-East (Cox’s Bazar) and South-West (Satkhira) coastal regions of Bangladesh. The VP28 gene-specific PCR assays and sequencing revealed statistically significant (p < 0.05, Kruskal Wallis test) differences in the prevalence of WSSV in shrimps and crabs between the study areas (Cox’s Bazar and Satkhira), and over the study periods (2017-2019). The mean Log load of WSSV varied from 8.40 (Cox’s Bazar) to 10.48 (Satkhira) per gram of tissue. The mean values for salinity, dissolved oxygen, temperature and pH were 14.71±0.76 ppt, 3.7±0.1 ppm, 34.11±0.38˚C and 8.23±0.38, respectively in the WSSV-positive ghers. The VP28 gene-based phylogenetic analysis showed an amino-acid substitution (E→G) at 167th position in the isolates from Cox’s Bazar (referred to as phylotype BD2) compared to the globally circulating one (BD1). Shrimp PL artificially challenged with BD1 and BD2 phylotypes with filtrates of tissue containing 0.423 X 109 copies of WSSV per mL resulted a median LT50 value of 73 hrs and 75 hrs, respectively. The in-vivo trial showed higher mean Log WSSV copies (6.47±2.07 per mg tissue) in BD1 challenged shrimp PL compared to BD2 (4.75±0.35 per mg tissue). Crabs infected with BD1 and BD2 showed 100% mortality within 48 hrs and 62 hrs of challenge, respectively with mean Log WSSV copies of 12.06±0.48 and 9.95±0.37 per gram tissue, respectively. Moreover, shrimp antimicrobial peptides (AMPs) penaeidin and lysozyme expression was lower in BD1 challenged group compared to BD2 challenged shrimps. These results collectively demonstrated that relative virulence properties of WSSV based on mortality rate, viral load and expression of host immune genes in artificially infected shrimp PL could be affected by single aa substitution in VP28.

Sometimes a pavement deflects only because of seasonal volume change of expansive soils in the pavement subgrade. Engineering practitioners expect an implementable and straightforward analysis method for a geosynthetic-reinforced pavement subjected to the swelling/shrinkage issue of expansive clayey subgrade, in an effort to find the bending moment, shear force and tension force distributions through the reinforced pavement, which are induced from the volumetric changes of subgrade soils. The virtual load method (VLM) was proposed in the past following the Timoshenko beam theory to analyze geosynthetic-reinforced pavement on expansive soils. In the VLM, the unknown virtual distributed load was obtained in the way by applying the inverse theory for the identification of material parameters of the pavement-foundation system. It was seen that the selection of the number of material parameters to obtain virtual load significantly affects the accuracy of the structural properties of the pavement and tensile properties of the geosynthetics if the linear least square method is used. In this paper, a unique numerical scheme was proposed in the hopes of solving the issue. After a forward problem was solved numerically, the Timoshenko beam deflection was taken as a start-up for the inverse problem to back analyze the load applied to the pavement. Solutions from forward/backward examples have explicitly shown the accuracy achieved related to the bending moment in the pavement and tension in the geosynthetic reinforcements. The proposed methodology can be applied for an in-depth understanding of the geosynthetic function for the mitigation of longitudinal cracks on pavements caused by heave/shrinkage of expansive soils.

A theoretical nonlocal thermoelastic model for studying the effects of the thermal conductivity variability on a rotating nanobeam has been described in the present article. The theory of thermal stress is employed using the Euler–Bernoulli beam model and generalized heat conduction with phase lags. It is believed that the thermal conductivity of the current model varies linearly according to temperature. Due to variable harmonic heat, the considered nanobeam excited and was subjected to a time-varying exponential decay load. Using the Laplace transform process, the analytical solutions for displacement, deflection, thermodynamic temperature and bending moment of rotating nanobeams are provided in final forms and a numerical example has been taken to address the problem. A comparison of the stated results was displayed and additionally, the influences of non-local parameters and varying load were analyzed and examined. We also investigate how the linear changes in the temperature of physical properties can influence both the static and dynamic responses to the rotating nanobeam.

Background: The question of whether children are less likely to pass on SARS-CoV-2 is important for planning society’s response to the pandemic. A document available on the Charité hospital website has not been formally published but is frequently referred to as supporting the notion that viral loads are similar in children and adults. Methods: The summary data from this document was extracted and used to produce summary statistics for three age groups: younger children (ages up to 11), older children (ages 12 to 19) and adults (ages 20 and above). Viral loads between the two children’s groups and the adult group were compared using Welch’s t test, which only requires group means and standard deviations and which is robust against moderate departures from normality. Findings: Viral loads were significantly lower than in adults for both younger children (p=0.04) and older children (p=0.04). Overall, viral loads were lower in children than adults (p=0.005). Interpretation: For both younger and older children, on average those with detectable SARS-CoV-2 have significantly lower viral loads than adults. Funding: No funding was received for this analysis.

Background: World Health Organization (WHO) declared that COVID-19 as a pandemic on March 11, 2020. There is sudden need of statistical modeling due to onset of COVID-19 pandemic across the world. But health planning and policy requirements the estimates of disease problem form clinical data. Objective: To predict recovery rate, cases load rate on the basis of cumulative confirmed Novel Corona virus (NCV) cases, recovered cases and deaths form COVID-19 in India. Methods: The reported COVID-19 cases in the country were obtained from website (https://datahub.io/core/covid-19#resource-covid-19_zip/). The cumulative NCV confirmed cases; recovery cases and deaths were used for estimating recovery rate, cases load rate and death rate till date 24 April 2020. Results: A total of 24530 NCV confirmed cases were reported nationwide in India on 24 April 2020. It is found that the recovery rate increased 22% and case load rate decreased 74%. Death rate is found to be very low 3%. The difference of cases load rate and recovery rate (delta) coincide at 50 % then NCV cases expected would be declined. Conclusion: The epidemic in the country was mainly caused by the importation of India. Lockdown as restricting the migration of population and decided to quarantine of population may greatly reduce the risk of continued spread of the epidemic in India. This study predicts that by 20 May 2020, the cases load rate lesser than recovery rate there after COVID-19 patients would be started to reducing.

The aim of this study was to clarify effects of 3-week work-matched high-intensity intermittent cycling training (HIICT) with different cadences on VO2max in university athletes. Eighteen university athletes performed HIICT with either 60 rpm (n = 9) or 120 rpm (n = 9). HIICT consisted of eight sets of 20-s exercise with a 10-s passive rest between each sets. The initial training intensity was set at 135% of VO2 max and was decreased by 5% every two sets. Athletes in both groups performed 9 sessions of HIICT during 3-week. The total work-load and achievement rate of the work load calculated before experiments in each group were used for analysis. VO2max was measured pre and post-training. After 3-week of training, no significant differences in the total work-load and achievement rate of the work load were found between the two groups. VO2max similarly increased in both groups from pre to post training (p = 0.016), with no significant differences between the groups (p = 0.680). These results suggest that cadence during HIICT is not training variable affecting effect of VO2max.

Due to the rapid development and popularity of the Internet, cloud computing has become an indispensable application service. However, how to assign various tasks to the appropriate service nodes is an important issue. Based on the reason above, an efficient scheduling algorithm is necessary to enhance the performance of system. Therefore, a Three-Layer Cloud Dispatching (TLCD) architecture is proposed to enhance the performance of task scheduling. In first layer, the tasks need to be distinguished to different types by their characters. Subsequently, the Cluster Selection Algorithm is proposed to dispatch the task to appropriately service cluster in the secondly layer. Besides, a new scheduling algorithm is proposed to dispatch the task to a suitable server in a server cluster to improve the dispatching efficiency in the thirdly layer. Basically, the TLCD architecture can obtain better task completion time than previous works. Besides, our algorithm and can achieve load-balancing and reliability in cloud computing network.

The Internet of Things (IoT) signifies a revolutionary technological advancement, enhancing various applications through device interconnectivity while introducing significant challenges due to these devices' limited hardware and communication capabilities. To navigate these complexities, the Internet Engineering Task Force (IETF) has tailored the Routing Protocol for Low-Power and Lossy Networks (RPL) to meet the unique demands of IoT environments. However, RPL struggles with traffic congestion and load distribution issues, negatively impacting network performance and reliability. This paper presents a novel enhancement to RPL by integrating learning automata designed to optimize network traffic distribution. This enhanced protocol, the Learning Automata-based Load-Aware RPL (LALARPL), dynamically adjusts routing decisions based on real-time network conditions, achieving more effective load balancing and significantly reducing network congestion. Extensive simulations reveal that this approach outperforms existing methodologies, leading to notable improvements in packet delivery rates, end-to-end delay, and energy efficiency. The findings highlight the potential of our approach to enhance IoT network operations and extend the lifespan of network components. The effectiveness of learning automata in refining routing processes within RPL offers valuable insights that may drive future advancements in IoT networking, aiming for more robust, efficient, and sustainable network architectures.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

Vehicular ad hoc networks (VANET) are a subset of mobile ad hoc networks used to communicate between vehicles and infrastructure. During vehicular congestion communication, nodes compete to acquire channels, causing the channels to become congested. The congestion on the vehicle network results in increased delay and packet loss, resulting in reduced VANET performance. To address this problem, we developed a load-aware and priority adaptive traffic congestion control method in vehicular ad hoc networks (VANETs). The proposed scheme identifies less-congested road segments based on the network's load and reduces traffic congestion by suggesting other routes between nearby roadside units (RSUs). This research aims to improve the efficiency of the vehicular environment by utilizing the movement of vehicles with (RSUs) and sharing the traffic load between them. Simulation results demonstrate the effectiveness of the proposed protocol in reducing congestion and enhancing the overall performance of VANETs. To validate the proposed algorithm, we have implemented and tested the proposed algorithm using Network Simulator 3 (NS3) for Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communication scenarios and computed the performance of the algorithm on different parameters of the network. The simulation result of the proposed load aware and priority adaptive traffic congestion control method in VANET improved the packet delivery ratio, packet lost ratio, and end-to-end delay by 96%, 4.1%, and 1102 milliseconds, when compared to TDCCA value of 92%, 5.7%, and 1154 milliseconds, respectively

(1) Background: Hepatitis B virus (HBV) viral load (VL) is useful in determining treatment eligibility, however, due to high costs associated with the test, hepatitis B e antigen (HBeAg) is recommended as a proxy for HBV VL in resource-limited settings. (2) Methods: We used 299 archived plasma samples with hepatitis B surface antigen (HBsAg), HBeAg, and HBV VL (cut-off of 20,000 IU/mL and 200,000 IU/mL) results from people living with human immunodeficiency virus (PLWH). HBeAg and HBV VL results were analyzed to evaluate the use of HBeAg to determine CHB treatment eligibility and qualification of HBV prevention of mother-to-child transmission (PMTCT) prophylaxis for the first time in Botswana. (3) Results: Approximately 70.8% and 87.5% of participants with HBeAg-positive serology had HBV viral loads ≥20,000 IU/mL and 200,000 IU/mL respectively. Using logistic regression, the odds of having a qualifying HBV VL for CHB treatment and PMTCT prophylaxis were respectively 55.5 and 110.4 times higher in participants with positive HBeAg serology indicating a statistically significant association between HBeAg status and HBV VL. (4) Conclusions: HBeAg detection may not always correlate with high HBV VL, warranting further research focusing on this association, and other biomarkers that correlate better with HBV VL.

High-density olive groves, despite their interesting production potential, have several limitations, also due to the high fruit load and the irrigation requirements.The study aimed to evaluate the effects of fruit load and deficit irrigation on oil yield and fruit quality, and on olive chemical composition in a high-density olive grove (cv Sikitita). Our main hypothesis was that the primary metabolism, as influenced by crop load and stress, could modify the accumulation of different phenolic classes.Different fruit loads were generated through flower thinning (66%, 50%, 33%, 0%) and two deficit irrigation treatments (-60%, -75%) were compared to the well-watered control (920 m3/ha).Thinning treatments had a limited effect on oil yield, on the other hand, deficit irrigation caused considerably less oil accumulation in the fruit on all sampling dates.Thinning 66% and deficit irrigation 75% were considered with the control for untargeted metabolomic analysis, considering three sampling dates. 233 different phenolic compounds were annotated. Multivariate HCA results indicated the impact of harvest time on the phenolic profile of olive fruits, yielding two separate clusters grouping t1 and t2 together and apart from t3. Regarding agronomic techniques, they played a differential role in the phenolic profile (supervised OPLS – DA). Fruit load mostly affected flavonoid glycosides. In contrast, the phenolic response to deficit irrigation is more heterogeneous, with phenolic acids (35%), flavonoids (25%), LMW, and other phenols (25%).

The chicken poultry business is becoming a crucial sector for our nation's sustainable food supply. To increase the health of chickens in coops and maybe increase the output of chicken meat and eggs, several innovations and inventions have been developed. Therefore, the creation of an automated chicken feeding device might be highly beneficial for the expansion of the poultry sector. This equipment may take the role of a worker in the chicken feeding process, solving the industry's labor shortage and introducing a semi-automatic procedure. The main processor of the automated chicken feeding system is a Raspberry Pi 3 Model B+. The machine consists of five main components: a Raspberry Pi with an amplifier that makes noise to draw the attention of free-range chickens, a Raspberry Pi with a pi camera that counts and detects the chickens, a Raspberry Pi with a servomotor that moves the food from storage to a container, a Raspberry Pi with a load cell that controls the number of feeds to avoid waste on foods, and a Raspberry Pi with a temperature sensor that monitors the food's freshness. This enhances the coop's atmosphere while lowering labor costs, conserving food, and ensuring that the chickens are fed on time. It also regulates the temperature sensor to ensure that the chicken food is fresh and prevents food from becoming polluted by insects and chicken excrement.

The ultimate aim of dynamic load balancing in cloud computing systems is to maximise the efficiency with which resources are utilised and workloads are distributed. Given that load balancing is a multi-objective process and that response time is a priority, the Harris hawk optimisation (HHO) algorithm was developed as a unique solution for dynamic load balancing. Based on burden distribution and resource utilisation, the HHO algorithm is responsible for dynamically assigning workloads to virtual machines (VMs). Through iterative interactions and position updates, the hawks investigate the solution space, determine the optimal method for dividing the work, and adapt to the ever-changing conditions of the workload. The HHO algorithm has been demonstrated to be effective and efficient in the management of dynamic load balancing via a series of experimental evaluations and comparisons with other load-balancing approaches. These discoveries have led to quicker response times and more efficient resource utilisation. Utilising the collaborative search behaviour of hawks, this technique provides a solution that is both practicable and effective for addressing load balancing concerns in dynamic scenarios.

This work discusses the relationship between foreign direct investment (FDI) and pollution in Spain using an autoregressive distributed lag regression model (ARDL) from 1961 to 2018. The authors apply the theoretical context of pollution haven/halo and conclude that FDI in Spain does not contribute to the transfer of green technologies for cleaner production, despite being included within the European environmental regulatory framework. The authors also verify the adequacy of the environmental Kuznets curve (EKC) and the Load Capacity Curve hypothesis (LCC) in the Spanish environmental context and find that income per capita has a positive effect on environmental sustainability and quality. In this sense, the further development of an efficient renewable energy infrastructure could efficiently drive to a better standards all pollution indexes in Spain, including nuclear energy production, contributing the emissions neutrality aimed by the EU by 2050.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Regarding the high efficiency of metaheuristic techniques in energy performance analysis, this paper scrutinizes and compares five novel optimizers, namely biogeography-based optimization (BBO), invasive weed optimization (IWO), social spider algorithm (SOSA), shuffled frog leaping algorithm (SFLA), and harmony search algorithm (HSA) for the early prediction of cooling load in residential buildings. The algorithms are coupled with a multi-layer perceptron (MLP) to adjust the neural parameters that connect the CL with the influential factors. The complexity of the models is optimized by means of a trial-and-error effort, and it was shown that the BBO and IWO need more crowded spaces for fulfilling the optimization. The results revealed that the internal parameters (i.e., biases and weights) suggested by the BBO generate the most reliable MLP for both analyzing and generalizing the CL pattern (with nearly 93 and 92% correlations, respectively). Followed by this, the IWO emerged as the second powerful optimizer with mean absolute errors of 1.8632 and 1.9110 in the training and testing phases. Therefore, the BBO-MLP and IWO-MLP can be reliably used for accurate analysis of the CL in future projects.

Heavy load carrying of water, firewood, and sand/stones is a ubiquitous activity for women living in developing countries. Although the intra-abdominal pressure associated with heavy load carrying is hypothesized to increase the risk of pelvic organ prolapse (POP) among women, relevant epidemiologic data are lacking. We conducted a comparative study involving two exploratory cross-sectional studies among convenience samples of women carrying heavy loads, with different characteristics: (1) as part of their activities for daily living, in Shinyanga region, Tanzania; and (2) working as sand miners in Pokhara, Nepal. Women were categorized has having “low” or “high” load-carrying exposures based on the measured weights of the loads being carried at the time of the survey, as well as on self-reported duration and frequency of load carrying. A summary score for lower abdominal discomfort suggestive of POP was generated using questions from the Pelvic Organ Prolapse Distress Inventory (POPDI-6). Women with higher load carrying exposures had on average higher discomfort scores in both Tanzania (adjusted prevalence difference (PDa)=3.7; 95% CI: -3.8-11.3; p=0.33) and Nepal (PDa=9.3; 95% CI: -4.9-23.6; p=0.18). We identified trends suggestive of an association between increasing heavy load carrying exposures and symptoms of lower abdominal discomfort. Our findings underscore the need for larger epidemiologic studies of the potential adverse reproductive health effects of heavy load carrying activities on women in developing countries.

Reinforced concrete (RC) columns are often placed under confinement to increase their strength and ductility. Carbon fiber reinforced polymer (CFRP) materials have recently been recognized as favorable confinement systems. At present, a number of national standards and codes dedicated to the design of concrete components strengthened with CFRP in general and CFRP confinement in particular are available. These sets of rules provide design equations for confined reinforced concrete columns with circular and rectangular cross sections. Most of the standards and codes exhibit significant differences, including the used predictive models limitations, observed effects, and covered loading conditions. In this paper, five international standards and design guidelines are introduced and discussed. The purpose is to present a constructive and critical assessment of the state-of-the-art design methodologies available for CFRP confined RC columns and to discuss effects not previously considered properly. Therefore, some recent research efforts and findings from the Leipzig University of Applied Sciences are also introduced. The obtained data is used for a comparative study of the guideline predictive equations. Furthermore, it is shown that some new findings concerning the rupture strength and the maximum strength plus accompanying axial strain of a CFRP confined column are suitable to improve the current guidelines.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

The aim of this study was to analyze the effects of the playing position (backs vs. pivots vs. wings) and the player role (starter vs. non-starter) on internal match-load and well-being status of female handball players after official matches. Fourteen female handball players from the Spanish 2^nd Division were monitored during a half-season (13 matches, n = 102 individual observations) using rate of perceived exertion (match-RPE) and the Hooper questionnaire in MD+1 and MD+2. Differences between playing positions and player role were determined by Kruskal-Wallis and Mann-Whitney U test, respectively. Furthermore, epsilon-squared (ε²) and Cohen's d (ES) were calculated and interpreted using Hopkins' categorization criteria. The results reveal that backs registered moderately more match-RPE compared to pivots (p < 0.05, ES = 0.84). In contrast, wings experienced the highest values of fatigue and muscle soreness in MD+1 and MD+2 compared to all other playing positions (p < 0.05, ES = 0.66-0.93). Also, wings reported moderately more Hooper index in MD+1 and MD+2 than backs (p < 0.01, ES = 0.73-0.77). Furthermore, starters reported higher absolute values of match-RPE, fatigue, muscle soreness and Hooper index in MD+1 compared to non-starters (p < 0.05, ES = 0.25-0.29). However, no differences were found in MD+2. Therefore, handball coaches and practitioners should consider the internal match-load and the well-being status of the players to implement different training stimulus (e.g., recovery or compensatory strategies) in MD+1 according to playing positions and player role to equalize the total weekly load of the players.

The Self-Forming Dynamic Membrane BioReactor (SFD MBR) is a cost-effective alternative to conventional MBR, where the synthetic membrane is replaced by the “cake layer”, an accumulation of the biological suspension over a surface of inert low-cost support, caused by a suction force. Under optimized conditions, the cake layer reveals easy to remove and quick to form again, resulting a “dynamic membrane”. The permeate of SFD MBR has chemo-physical characteristics comparable to those of conventional MBR. In this paper, two nylon meshes with a pore-size of 20 and 50 µm respectively were tested in a bench scale SFD MBR where a periodic air mass load (AML) was supplied tangential to the filtration surface to maintain filtration effectiveness. The SFD MBR equipped with the 20 µm nylon mesh coupled to 5 min of AML every 4 hours showed the best performance both ensuring a permeate with turbidity values always below 3 NTU and revealing no critical fouling. A benchmark test, conducted in the same experimental time, with identical operating conditions, and the only difference of a suction break (relaxation) instead of the AML. This latter test produced a permeate of very good quality, but it needed frequent mesh cleanings, showing that a periodic AML coupled with the use of a 20 µm mesh can be a good strategy for long term operation of SFD MBR.

Abstract: Considering the significance of postural balance in shooting ability, and consequently soldiers’ occupational performance and survivability, it is of importance to promote the use of balance training programs to improve shooters' efficiency. This study explored how a balance training program affects shooting performance. Twenty participants were divided into two equal groups. They all performed 60 shots in a shooting simulator while standing. The participants went through this process twice, before and after a 4-week balance training program. The shoot-ing was done under four different conditions: without load on a stable surface, with load on a stable surface, without load on an unstable surface, and with load on an unstable surface. The training program had a significant impact on the experimental group, improving their balance by 76 ± 9% (p < 0.01). Additionally, in the experimental group, shooting score increased by 47% and the % center of gravity by 20% (p < 0.01). The stability of the shots, measured by holding time in the target, doubled from 2.2 to 4.5 seconds (p < 0.01). These improvements were more pronounced when participants had a load and/or were on an unstable surface. In conclusion, a balance training program can be beneficial for improving shooting performance.

With a software-defined network (SDN), the control plane is separated from the data plane, allowing the control of network flows to be easy and dynamic at the same time. While the controller, which is equipped with various control applications, is capable of analyzing a large amount of data, it may become overburdened when it is faced with a large volume of traffic. The intrusion detection system (IDS) is an example of control applications that can be used to detect intrusions. It is recommended to deploy instances of the IDS across the data plane. This will improve the processing power and detection rate and as a result reduce the load on the controller at the same time. While there is no doubt that an IDS would be beneficial for improving detection rates, installing one at each switch in the data plane would be costly. To address this issue, this paper proposes the deployment of IDS chains across the data plane. The controller directs incoming traffic via alternative paths, including the IDS chain, which increases the detection rate while avoiding overloading. In order to improve transmission efficiency, our study proposes a method of balancing the distribution of flows and assigning them to specific IDS chains. This approach minimizes the cost of flow grouping through the use of a new incoming traffic grouping technique. Our method is tested and evaluated through the use of a test bed and trace-based simulation, and has been proven to effectively reduce delays and hop counts across various traffic scenarios.

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

A thermal load dispatch problem minimizes the number of objectives viz operating cost and emission of gaseous pollutants together while allocating the power demand among the committed generating units subject to physical and technological system constraints. A stochastic thermal load dispatch problem is undertaken while taking into consideration, the uncertainties, errors in data measurements and nature of load demand which is random. Owing to uncertain load demand, variance due to mismatch of power demand termed as risk, is considered as another conflicting objective to be minimized. Generally multiobjective problems generate a set of non-inferior solutions are generated and supplied to a decision maker to select the best solution from the set of non-inferior solutions. This paper proposes opposition-based greedy heuristic search (OGHS) method to generate a set of non-inferior solutions. Opposition-based learning is applied to generate initial population to select good candidates. Migration to maintain diversity in the set of feasible solutions is also based on opposition-based learning. Mutation strategy is implemented by perturbing the genes heuristically in parallel and better one solution is sought for each member. Feasible solutions are achieved heuristically by modifying the generation-schedules in such a manner that violation of operating generation limits are avoided. The OGHS method is simple to implement and provides global solutions derived from the randomness of the population generated without tuning of parameters. Decision maker exploits fuzzy membership functions to decide the final decision. Validity of the method has been demonstrated by analysing systems in different scenarios consisting of six generators and forty generators.

Novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants of concern (VOC) are constantly threatening global public health. With no end date, the pandemic still persists with the emergence of novel variants that threaten the effectiveness of diagnostic tests and vaccines. Mutations in the Spike surface protein of the virus are regularly observed in the new variants, potentializing the emergence of novel viruses with different tropism from the current ones, which may change the severity and symptoms of the disease. Growing evidence has shown that mutations are being selected in favor of variants that are more capable of evading the action of neutralizing antibodies. In this context, the most important factor guiding the evolution of SARS-CoV-2 is its interaction with the host’s immune system. Thus, as current vaccines cannot block the transmission of the virus, measures complementary to vaccination, such as the use of masks, hand hygiene, and keeping environments ventilated remain essential to delay the emergence of new variants. Importantly, in addition to the involvement of the immune system in the evolution of the virus, we highlight several chemical parameters that influence the molecular interactions between viruses and host cells during invasion and are also critical tools making novel variants more transmissible. In this review, we dissect the impacts of the Spike mutations on biological parameters such as (1) increase of Spike binding affinity to hACE2; (2) bound time for the receptor to be cleaved by the proteases; (3) how mutations associate with increase of RBD up-conformation state in the Spike ectodomain; (4) expansion of uncleaved Spike protein in the virion particles; (5) increment of Spike concentration per virion particles; and (6) evasion of the immune system. These factors play key roles in the fast spreading of SARS-CoV-2 variants of concern, including the Omicron.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

: The significance of heating load (HL) accurate approximation is the primary motivation of this research to distinguish the most efficient predictive model among several neural-metaheuristic models. The proposed models are through synthesizing multi-layer perceptron network (MLP) with ant lion optimization (ALO), biogeography-based optimization (BBO), dragonfly algorithm (DA), evolutionary strategy (ES), invasive weed optimization (IWO), and league champion optimization (LCA) hybrid algorithms. Each ensemble is optimized in terms of the operating population. Accordingly, the ALO-MLP, BBO-MLP, DA-MLP, ES-MLP, IWO-MLP, and LCA-MLP presented their best performance for population sizes of 350, 400, 200, 500, 50, and 300, respectively. The comparison was carried out by implementing a ranking system. Based on the obtained overall scores (OSs), the BBO (OS = 36) featured as the most capable optimization technique, followed by ALO (OS = 27) and ES (OS = 20). Due to the efficient performance of these algorithms, the corresponding MLPs can be promising substitutes for traditional methods used for HL analysis.

Early prediction of thermal loads plays an essential role in analyzing energy-efficient buildings' energy performance. On the other hand, stochastic algorithms have recently shown high proficiency in dealing with this issue. These are the reasons that this work is dedicated to evaluating an innovative hybrid method for predicting the cooling load (CL) in buildings with residential usage. The proposed model is a combination of artificial neural networks and stochastic fractal search (SFS-ANN). Two benchmark algorithms, namely the grasshopper optimization algorithm (GOA) and firefly algorithm (FA), are also considered to be compared with the SFS. The non-linear effect of eight independent factors on the CL is analyzed using each model's optimal structure. Evaluation of the results outlined that all three metaheuristic algorithms (with more than 90 % correlation) can adequately optimize the ANN. In this regard, this tool's prediction error declined by nearly 23, 18, and 36 % by applying the GOA, FA, and SFS techniques. Also, all used accuracy criteria indicated the superiority of the SFS over the benchmark schemes. Therefore, it is inferred that utilizing the SFS along with ANN provides a reliable hybrid model for the early prediction of CL.

Dynamic visualizations have been developed to exchange information that transforms over time across a broad range of professional and academic contexts. However, these visual tools may impose substantial demands on the learner’s cognitive resources that are very limited in current knowledge. Cognitive load theory has been used to improve learning from dynamic visualizations by providing certain design techniques to manage learner cognitive load without adding any oral/written explanations. This systematic review examined a series of experimental studies assessing the roles of these design techniques in learning tactical scenes of play through dynamic visualizations. Electronic databases PubMed and Google Scholar were used to search relevant articles. Eleven studies were eventually included for the systematic review based on the eligibility criteria. The present review revealed that adapting design techniques to the level of learners’ expertise, type of depicted knowledge, and level of content complexity is a crucial part of effective learning.

The variations in socioeconomic status (SES) between different social classes of a population correspond to differences in accessibility to all resources available and able to improve global health. SES can influence global health trajectory for an individual or a community, depending if SES is low or high. Sleep is sensitive to environmental stimuli, as well as living conditions. Plenty of studies linked sleep complaints with mood disorders, allostatic load or circadian disruption; but very few or none investigated deeply what happened earlier to sleep depending of SES. While SES is now known as one of the main determinants for a good health and a good aging, its influence on sleep disorders (SD) is not well understood. SES is a concept, not directly observable but estimated using indicators like income, education, occupational status and area of living. Even if recent evidence suggested that few of SES indicators like occupational status are linked with sleep disturbances, the relation between SES and health in general with sleep as an outcome or a mediator is not well documented. This scoping review synthetized studies which investigated physiological and psychological mechanisms resulting from a low SES and linked them with sleep disturbances as consequences or as mediators. This review also explore a possible role played by sleep in the relation between socioeconomic status and health inequalities.

The aim of this paper is to at first evaluate the influence of three key parameters including weld current, weld time and electrode force on nugget diameter and tensile strength in resistance projection welding. Then, a 2-D axis-symmetric finite element model is developed to simulate the projection welding and predict the nugget diameter. Finally, the FEM results are compared to experimental data to verify the simulation model and simulated results. In the finite element model, the temperature-dependent material properties were taken into account.

Policing duties may inherently be dangerous due to stab, blunt trauma and ballistic threats. The addition of individual light armour vests (ILAVs) has been suggested as a means to protect officers. However, the addition of the extra load of the ILAV may affect officer ability to conduct occupational tasks. The purpose of this study was to determine if wearing any of 3 different ILAVs (ILAV A, ILAV B, & ILAV C) affected occupational task performance when compared to that in normal station wear. A prospective, within-subjects repeated measures design was employed, using a counterbalanced randomization in which each ILAV was worn for an entire day while officers completed a variety of occupationally relevant tasks. These tasks included a victim drag, car exit and 5 meter sprint, step down and marksmanship task. Results showed that performance in each task did not vary between any of the ILAV or normal station wear conditions. There was less variability in the marksmanship task with ILAV B, however. The results suggest that none of the ILAVs used in this study were heavy enough to significantly affect task performance in the assessed tasks when compared to wearing normal station wear.

In this study, the probabilistic exergoeconomic analysis was performed for four industrial gas turbine (GT) units comprising of two (GT16 and GT19) units of 100MW GE engine and two (GT8 and GT12) units of 25MW Hitachi engine at Transcorp Power Limited, Ughelli. These four industrial GT engine units were modelled and simulated using natural gas as fuel. The design point (DP) simulation results of the modelled GT engines were validated with the available DP thermodynamic data from original equipment manufacturer (OEM). This was done before the off-design point (ODP) simulation was carried out which represents the plant operations. The results obtained from exergy analysis at full load operation show that the turbine has the highest exergy efficiency followed by compressor and combustion having the least. For turbines these were 96.13% for GT8 unit, 98.02% for GT12 unit, 96.26% for GT16 unit, and 96.30% for GT19 unit. Moreover, the combustion chamber has the highest exergy destruction efficiency of 55.16% GT8 unit, 56.58% GT12 unit, 43.90% GT16 unit, and 43.30% GT19 unit respectively. The exergy analysis results obtained from the four units show that the combustion chamber (CC) is the most significant exergy destruction with lowest exergy efficiency and highest exergy destruction efficiency of plant components. The exergoeconomic analysis results from four units showed combustion chamber energy destruction cost of 531.08 $/h GT8 unit, 584.53 $/h GT12 unit, 2351.81$/h GT16, and 2315.93$/h GT19 unit. The probabilistic results analysis based on the input parameters distributions evaluated and discussed.

In the context of high energy costs and energy transition, the optimal use of energy resources for industrial consumption is fundamental. This paper presents a decision-making structure for large consumers having flexibility to manage electricity or natural gas consume to satisfy the demands of industrial processes. The proposed modelling energy system structure relates monthly medium and hourly short-term decisions to which these agents are subjected, represented by two connected optimization models. In the medium term, the decision occurs under uncertain conditions of energy and natural-gas market prices, as well as hydropower generation (self-production). The monthly decision is represented by a risk-constrained optimization model. In the short term, hourly optimization considers the operational flexibility of energy and/or natural-gas consumption, subject to the strategy defined in the medium term and mathematically connected by a regret cost function. The model application of a real case of a Brazilian aluminum producer indicates a measured energy cost reduction of U$ 3.98 million over a six-month analysis period.

Monitoring training load, recovery, and wellness in maturation ages is even more relevant than in adulthood, especially during congested schedules. The objective of this study was to quantify and describe the differences in external and internal load, recovery, and perceived wellness in elite under-16 female players during a period of three competitions in seven days, based on their participation during matches. An observational design was used to quantify external load (total distance, high-speed distance, and PlayerLoad), internal load (differential sRPE), as well as recovery and wellness of 18 international under-16 players during a development tournament. The external load pattern of the starting players was undulating, with matches showing the highest internal load values compared to training sessions and non-starters. Non-starters players (whether training or matches) showed similar external load and differential sRPE values throughout the tournament (p&gt;0.05). Starting players experienced higher internal load than non-starters during matches (p&lt;0.037), without differences between training sessions (p&gt;0.05). No changes were seen in wellness or recovery (all p-values &gt;0.05), except for non-starters in session 3 compared to session 7 (p=0.024). Starting players had more weekly total minutes (p=0.018), differential sRPE (breath: p=0.002; leg: p=0.002; cognitive: p=0.003), total distance (p=0.003), and PlayerLoad (p=0.008) than non-starters. Our results indicate differing load patterns between starters and non-starters, which do not affect wellness and recovery differently. Starters accumulate more weekly total load. Coaches can use these findings to guide decisions and load compensations in high competition contexts for young female soccer players.

In a motor-controlled hydraulic cylinder (MCC), the two chambers of the cylinder are directly connected to single or multiple fixed-displacement hydraulic pumps driven by electric servo motors. In contrast to a valve-controlled cylinder, an MCC does not have valve throttling, resulting in an improved system energy efficiency. Among various MCC topologies, the two-motor-two-pump (2M2P) MCC distinguishes itself through several notable advantages, including precise cylinder pressure control and eliminating mode switch oscillations. Nevertheless, there are remaining challenges in fully realizing its operations across four quadrants and establishing an effective load-holding function within these operations. This study bridges this gap by implementing a 2M2P MCC prototype on a laboratory knuckle boom crane, enabling operation across all four quadrants. Experimental results indicate that position tracking errors remain within ±2.5 mm across three cases. Furthermore, smooth intersection of cylinder bore side and rod side pressures is observed during transitions between quadrants. In conclusion, the proposed 2M2P MCC demonstrates seamless operation throughout all quadrants, with the load-holding function smoothly activating and deactivating in all four quadrants.

Background: Previous neuroimaging studies have identified brain regions related to respiratory motor control and perception. However, little is known about the resting-state functional connectivity (FC) associated with respiratory impairment. We aimed to determine the FC involved in mild respiratory impairment without changing the saturation of percutaneous oxygen. Methods: We obtained resting-state functional magnetic resonance imaging data from 36 healthy volunteers during normal respiration and mild respiratory impairment induced by resistive load (effort breathing). ROI-to-ROI and seed-to-voxel analyses were performed using Statistical Parametric Mapping 12 and the CONN toolbox. Results: Compared to normal respiration, effort breathing activated FCs within and between the sensory perceptive area of respiration (the postcentral gyrus, anterior insular cortex (AInsula), and anterior cingulate cortex) and visual cortex (the visual occipital, occipital pole (OP), and occipital fusiform gyrus). Graph theoretical analysis showed strong centrality in the visual cortex. A significant positive correlation was observed between the dyspnoea score (modified Borg scale) and FC between the left AInsula and right OP. Conclusions: These results suggested that the FCs within the respiratory sensory area via the network hub may be neural mechanisms underlying effort breathing and modified Borg scale scores.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Commercial buildings situated in hot and humid tropical climates rely significantly on cooling systems to maintain optimal occupant comfort. A well-accurate day-ahead load profile prediction plays a pivotal role in planning the energy requirements of cooling systems. Despite the pressing need for effective day-ahead cooling load predictions, current methodologies have not fully harnessed the potential of advanced deep-learning techniques. This research paper aims to address this gap by investigating the application of innovative deep learning models in day-ahead hourly cooling load prediction for commercial buildings situated in tropical climates. A range of deep learning techniques, including Deep Neural Network, Convolutional Neural Networks, Recurrent Neural Networks, and Long Short-Term Memory networks are employed to enhance prediction accuracy. Furthermore, these individual deep learning techniques are synergistically integrated to create hybrid models, such as CNN-LSTM and Sequence-to-Sequence models. An extensive comparative analysis is conducted to identify the most effective hybrid model. Sequence-to-sequence model provided better performance compared to the other single and hybrid models. Experiments are conducted to choose the time horizons from the past that can serve as input to the models. Further, the influence of various categories of input parameters on prediction performance has been assessed. Historical cooling load, calendar features and outdoor weather parameters are found in decreasing order of influence on prediction accuracy. This research focuses on buildings located in Singapore and presents a comprehensive case study to validate the proposed models and methodologies.

Against the backdrop of the current carbon peaking and carbon neutrality policies, higher requirements have been put forward for the upgrading and construction of smart grids. Non-intrusive load monitoring (NILM) technology is a key technology for advanced measurement systems at the end of the power grid. It obtains detailed power information of the load, without the need for traditional hardware deployment. The key step to solve this problem is load decomposition and identification. This paper first utilized Long Short Term Memory-Denoising Autoencoder(LSTM-DAE) to decompose the mixed current signal on the household busbar and obtain the current signals of multiple independent loads that constituted the mixed current. Then, the obtained independent current signals were combined with voltage signals to generate multi-cycle colored Voltage-Current(VI) trajectories, which were color-coded according to the background. These colored VI trajectories with background colors formed a feature library. When the CNN network was used for load recognition, considering the influence of hyperparameters on recognition results, the BOA algorithm was used for optimization, and the optimized CNN network was employed for VI trajectory recognition. Finally, the proposed method was validated using the PLAID dataset. Experimental results showed that the proposed method exhibited better performance in load decomposition and identification.

The COVID-19 pandemic has led to the growth of hybrid and online learning environments and the trend to introduce more technology into the classroom. One such change would be the use of smart synchronous hybrid learning environments (SSHLE), which are settings with both in-person and online students concurrently, and in which technology plays a key role in sensing, analyzing, and reacting throughout the teaching and learning process. These changing environments and the incorporation of new technologies can place a greater orchestration load on participants and a reduction in teacher agency. In this context, the aim of this paper is to analyse the orchestration load and teacher agency in different SSHLEs. The NASA-TLX model was used to measure the orchestration load in several scenarios. Questionnaires and interviews were used to measure teacher agency. The results obtained indicate that the orchestration load of the teacher tends to be high (between 60 and 70 points out of 100 of the NASA-TLX workload), especially when they lack experience in synchronous hybrid learning environments, and the orchestration load of the students tends to have average values (between 50 and 60) in the SSHLEs analysed. Meanwhile, the teacher agency does not appear to be altered but shows potential for improvement.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

In the course of SARS-CoV-2 infection, the 3CL or nsp5 protease plays a pivotal role as the most important viral protease required for the maturation of viral proteins during host infection. Herein, we simulated for 500 ns 3CLproWT, 3CLproH41A, , 3CLproBeta, and 3CLproOmicron, in complex with the substrates nsp 4|5 and nsp 5|6. Our results show that mutations in the 3CLpro present in the SARS-CoV-2 variant of concerns (VOCs) did not lead to significant conformational changes or changes in substrate binding affinities. However, significantly high cleavage rates for the boundary between nsp4 and nsp5 were obtained for 3CLproBeta and 3CLproOmicron and may play a key role in the viral replication and virus fitness gain. Our molecular dynamics data suggest that the cleavage rate of nsp4|5 may be related to the increased amount of viral load observed for these VOCs, releasing more nsp4 than other non-structural proteins. Based on our hydrogen bonding analyses, we also discovered that Gly143 and Glu166 are key residues in substrate recognition, suggesting that these residues may be incorporated as pharmacophoric centers for Beta and Omicron variants in drug design. Our results suggest that Gly143 and Glu166 are essential residues to interact with Gln6 of the different substrates and, therefore, are potential broad-spectrum pharmacophoric centers of SARS-CoV-2 3CLpro.

Lung cancer is the most common cause of cancer deaths worldwide, and lung adenocarcinoma (LUAD) is the most common histological subtype. However, the prognostic and predictive outcomes differ because of the heterogeneity of programmed cell death. The purpose of this work is to investigate and develop a cuproptosis-associated lncRNA-based LUAD prediction marker. We firstly performed bioinformatic analysis of the Cuprotosis database and The Cancer Genome Atlas (TCGA) database to obtain 19 cuprotosis-related gene datasets and transcriptional data for LUAD. Univariate, least absolute shrinkage and selection operator (LASSO), and multivariate Cox regression analysis were utilized to construct cuproptosis-associated lncRNA modes. LUAD patients were thus classified into high-risk and low-risk categories based on prognostic risk values, with a median of It acted as a boundary. Risk models were evaluated and validated using Kaplan-Meier analysis, principal component analysis (PCA), gene set enrichment analysis (GSEA) and nomograms. Utilizing the TCGA-LUAD dataset, we identified seven predicted cuproptosis-associated lncRNAs in tumor microenvironment to create the risk model. 95.54% (214/224) of high-risk category tumor samples included cuproptosis-associated gene alterations, compared to 85.65% (203/237) of low-risk category tumor samples, with TP53 accounting for the bulk of occurrences. According to these findings, risk value was superior to other clinical variables and tumor mutation burden as a predictor of 1-, 3-, and 5-year overall survival (OS). The predictive validity of the cuproptosis-associated lncRNA-based risk model for LUAD is high, and this may have implications for how lung cancer patients are treated individually.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

The tiered laboratory framework for HIV viral load monitoring accommodates a range of HIV viral load testing platforms, with quality assessment critical to ensure quality patient testing. HIV plasma viral load testing is challenged by the instability of viral RNA. An approach using an RNA stabilizing buffer is described for the Xpert® HIV-1 Viral Load (Cepheid) assay and was tested in remote laboratories in South Africa. EDTA-plasma panels with known HIV viral titres were prepared in PrimeStore molecular transport medium for per-module verification and per-instrument external quality assessment. The panels were transported at ambient temperatures to 13 testing laboratories during 2017 and 2018, tested according to standard procedures and uploaded to a web portal for analysis. A total of 275 quality assessment specimens (57 verification panels and two EQA cycles) were tested. All participating laboratories met study verification criteria (n=171 specimens) with an overall concordance correlation coefficient (ρ_c) of 0.997 (95% confidence interval [CI]: 0.996 to 0.998) and a mean bias of -0.019 log cp/mL (95% CI: -0.044 to 0.063). The overall EQA ρ_c (n=104 specimens) was 0.999 (95% CI: 0.998 to 0.999), with a mean bias of 0.03 log cp/mL (95% CI: 0.02 to 0.05). These panels are suitable for use in quality monitoring of Xpert® HIV-1 VL and are applicable to laboratories in remote settings.

The power system vulnerability leads to faults and the severity of the fault may lead to prolonged load-shedding. The power system needs to be configured in extreme failure scenarios for protecting the network from further contingencies and prolonged load-shedding. Distributed generation resources (DGs) can be useful to form intentional islands after faults to maintain the continuity of power supply to loads based on their weightage during faulty periods and to reduce overall load shedding duration. Power system is bound to collapses and secondary collapse in the formed island is possible. This research represents a novel method of impedance based path finding for intentional islanding, which adapts itself with the changes in the demands, DGs outputs or further severities during restoration period. In this adaptive islanding approach, network adjusts itself with the changes in either the load demands or renewable DGs outputs and rearranges the restoration plan by curtailing or adding some of the loads through controllable switches. Further a secondary collapse in the existing island is studied by injecting multiple faults at various positions of the network to validate the system resilience to cope with severities. A short-term load forecasting approach is used to predict changes in load demands and variations in DG outputs during the islanding scheme. During the restoration period, these variations are tracked and the islands are modified accordingly. In order to minimize the overall generation cost by using less fuel, an economical approach is used in the selection of controllable DGs. The proposed approach is formulated as a multi-objective, that incorporates several operational constraints and simulation is carried out using the modified IEEE 69-bus distribution system to assess the efficacy of the proposed model.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

This study examined the effects of incorporating 8 weeks of biweekly upper limb loaded plyometric training (elastic band) into the in-season regimen of handball players. Trial participants were assigned between control (n = 15, age: 18.1±0.5 years, body mass: 73.7±13.9 kg) and experimental (n = 14, age: 17.7±0.3 years, body mass: 76.8±10.7 kg) groups. Measures obtained pre- and post- included a cycle ergometer force-velocity test, ball throwing velocity in three types throw, 1-RM bench press and pull-over, and anthropometric estimates of upper limb muscle volumes. Gains in the experimental group relative to controls included absolute muscle power (W) (Δ23.3%; t-test p<0.01; d=0.083), relative muscle power (W.kg-1) (Δ22.3%; t-test p<0.01; d=0.091), and all 3 types of ball throw (Δ18.6%, t-test p<0.01, d=0.097 on jumping shot; Δ18.6%, t-test p<0.01; d=0.101 on 3-step running throw; and Δ19.1%, t-test p<0.01, d=0.072 on standing throw). Furthermore, a significant improvement by time interactions was observed in both groups on 1-RM bench press and pull-over performance. However, upper limb muscle volumes remained unchanged in both groups. We conclude that adding biweekly elastic band plyometric training to standard training improves measures important to game performance. Accordingly, such exercises can usefully be adopted as a part of handball training.

The growing number of the accessed energy-efficient frequency conversion air conditioners is likely to generate a large number of harmonics on the power grid. The following shortage in the reactive power of peak load may trigger voltage collapse. Hence, this conflicts with people’s expectations for a cozy environment. Concerning the problems mentioned above, an active management scheme is put forward to balance the electricity use and the normal operation of air conditioning systems. To be specific, schemes to suppress the low voltage ride through (LVRT) and harmonic are designed firstly. Then to deaden the adverse effects caused by nonlinear group load running on the grid, and to prevent the unexpected accidents engendered from grid malfunction, the dynamic sensing information obtained by an online monitor is analyzed, which can be seen as an actively supervise mechanism. The combined application of active and passive filtering technology is studied as well. Thirdly, the new energy storage is accessed reliably to cope with peak-cutting or grid breaking emergencies, and the fuzzy control algorithm is researched. Finally, system feasibility is verified by functional modules co-operation simulation, and active management target is achieved under scientific and reasonable state-of-charge (SOC) management strategy.

Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

The variations in socioeconomic status (SES) between different social classes of a population correspond to differences in accessibility to all resources available and able to improve global health. While SES is now known as one of the main determinants for a good health and a good aging, its influence on sleep disorders (SD) is not well understood. SES is a concept, not directly observable but estimated using indicators like income, education, occupational status and area of living. This theoretical review explores some theories linking environment of people with occurrence of SD, with different patterns associated to SES. A model of interaction is proposed to summarize and conceptualizes these interactions and to promote more research on the topic.