The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

The functions of annexin A1 (ANXA1) that is expressed on membranes and in cytoplasmic granules have been fully described. Nonetheless, the role of this protein in protecting against DNA damage in the nucleus is still emerging and requires further investigation. Here, we investigated the involvement of ANXA1 in DNA damage response in placental cells. Placenta was collected from ANXA1 knockout mice (AnxA1-/-) and pregnant women with gestational diabetes mellitus (GDM). The placental morphology and ANXA1 expression, which are related to the modulation of cellular response markers in the presence of DNA damage, were analyzed. Total area of AnxA1-/- placenta was smaller because of reduced labyrinth zone, enhanced DNA damage, and impaired base excision repair (BER) enzymes, which resulted in the induction of apoptosis in the labyrinthine and junctional layers. The placentas from pregnant women with GDM showed reduced expression of AnxA1 in the villous compartment, increased DNA damage, apoptosis, and reduction of enzymes involved in the BER pathway. Our translational data provide valuable insights into the possible involvement of ANXA1 in the response of placental cells to oxidative DNA damage and represent advancement in investigations on the mechanisms involved in placental biology.

Abstract: Pomegranate peels are important source of polyphenols with remarkable interest in food, pharmaceutical and cosmetic industry. An improved extraction of total polyphenolic com-pounds (TPC) from pomegranate peels by Solid-State Fermentation (SSF) was achieved. A Box Hunter & Hunter (BHH) followed by Central Composite Design (CCD) were performed to assess the effect of the process variables on TPC release. The statistic designs indicate that the best TPC extraction (234.85 mg GAE/gdm) by means of SSF occurs, at 42°C, 50 % moisture, pH 5.0, mineral solution (g/L): NaNO3 (3.83), KH2PO4 (1.52), MgSO4 (4.66) and KCl (1.52) at 36 h. At the best fer-mentation conditions, TPC (248.78±1.24 mgGAE/gdm) increased 5.96-fold than values previously reported and antioxidant activity [AA] increased 5.81-fold than the value obtained before the SSF optimization. High-valued citric acid, α and β punicalin, α and β punicalagin, punigluconin, gal-loyl-HHDP hexoside and ellagic acid molecules were identified. The increased extraction of TPC by SSF provides a suitable alternative for pomegranate peels valorization through the re-covery of molecules with high added value with potential use in food, pharmacy and cosmetic industries; a diversification in the use of food agroindustry by-products is obtained as approach to the circular economy model through biotechnological processes.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Purpose: This study investigates the impact of different intensity normalization (IN) methods on the overall survival (OS) radiomics models’ performance of MR sequences in primary (pHGG) and recurrent high-grade glioma (rHGG). Methods: MR scans acquired before radiotherapy were retrieved from two independent cohorts (rHGG C1: 197, pHGG C2: 141) from multiple scanners (15, 14). The sequences are T1 weighted (w), contrast-enhanced T1w (T1wce), T2w, and T2w-FLAIR. Sequence-specific significant features (SF) associated with OS, extracted from the tumour volume, were derived after applying 15 different IN methods. Survival analyses were conducted using Cox proportional hazard (CPH) and Poisson regression (POI) models. A ranking score was assigned based on the 10-fold cross-validated (CV) concordance index (C-I), mean square error (MSE), and the Akaike information criterion (AICs), to evaluate the methods’ performance. Results: Scatter plots of the 10-CV C-I and MSE against the AIC showed an impact on the survival predictions between the IN methods and MR sequences (C1/C2 C-I range: 0.62-0.71/0.61-0.72, MSE range: 0.20-0.42/0.13-0.22). White stripe showed stable results for T1wce (C1/C2 C-I: 0.71/0.65, MSE: 0.21/0.14). Combat (0.68/0.62, 0.22/0.15) and histogram matching (HM, 0.67/0.64, 0.22/0.15) showed consistent prediction results for T2w models. They were also the top-performing methods for T1w in C2 (Combat: 0.67, 0.13; HM: 0.67, 0.13), however, only HM achieved high predictions in C1 (0.66, 0.22). After eliminating IN impacted SF using Spearman’s rank-order correlation coefficient, a mean decrease in the C-I and MSE of 0.05 and 0.03 was observed in all four sequences. Conclusion: The IN method impacted the predictive power of survival models. Thus, performance is sequence-dependent.

Evolutionary ecology may be described as explaining ecology through evolution and vice versa, but one may also view it as an integration of the two fields, where one takes the view that ecology and evolution are inseparable, and one can only begin to understand the biology of organisms by synthesizing the two fields. An example of such a synthesis is the biology of high fecundity and the associated concept of sweepstakes reproduction, or skewed individual recruitment success. As an illustration we consider selection at linked sites under various dominance and epistasis mechanisms in a diploid population evolving according to random sweepstakes and experiencing recurrent bottlenecks. Using simulations we give a few examples of the impact of the stated elements on selection. We show that depending on the dominance mechanisms random sweepstakes can shorten the time to fixation (conditional on fixation) of the fit type at all sites. Bottlenecks tend to increase the fixation time, with random sweepstakes counteracting the effects of bottlenecks on the fixation time. Understanding the effect of random sweepstakes, recurrent bottlenecks, dominance mechanisms and epistasis on the fate of selectively advantageous mutations may help with explaining genetic diversity in natural highly fecund populations possibly evolving under sweepstakes reproduction.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

Background: Some patients who have recovered from COVID-19 have experienced a range of persistent symptoms or the appearance of new ones after a SARS-CoV-2 infection. These symptoms can last from weeks to months, impacting everyday functioning to a significant number of patients. Methods: A cross-sectional analysis based on an online, self-reporting questionnaire was conducted in Ecuador from April to July 2022. Participants were invited by social media, radio, and TV to voluntarily participate in our study. A total of 2103 surveys were included in this study. We compared socio-demographic variables and long-term persisting symptoms at low (< 2,500 m) and high altitude (>2,500 m).Results: Overall, 1100 (52.3%) responders claimed to have long-term symptoms after SARS-CoV-2 infection. Most of these symptoms were reported by women (64.0%), the most affected group was young adults (68.5%), and the majority of long-haulers were mestizos (91.6%). We found that high altitude residents were more likely to report persisting symptoms (71.7%) versus those living at lower altitudes (29.3%). The most common symptoms were fatigue or tiredness (8.4%), hair loss (5.1%) and difficulty concentrating (5.0%). The highest proportion of persisting symptoms was observed among those who received an incomplete vaccine scheme.Conclusions: This is the first study describing post-COVID symptoms' persistence in low and high-altitude residents. Our findings demonstrate that women, especially those aging between 20-40, are more likely to describe sequalae associated with post-COVID. We also found that living at a high altitude was associated with earlier onset and longer symptom duration. Finally, we found a greater risk to report long lasting symptoms among women, those with previous comorbidities and those who had a severer acute SARS-CoV-2 infection.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.

This article discusses a transformer-free, high-efficiency DC-DC converter besides renewable energy applications. The traditional buck-boost, classic Zeta, Sepic, and Cuk converter does have the benefits of a simple design, low cost, as well as the capacity to execute voltage step-up and step-down. Conversely, because of the detrimental consequences of the parasitic constraints of the device, the voltage conversion gain of the traditional DC-DC converter is much more restricted and the efficiency is also significantly smaller, whereas this proposed converter does have a higher voltage gain and efficiency because it is used in a single power switch, resulting in reduced switching losses and voltage stress. The said converter's design is very simple, which simplifies the operation control and reduces switching and conduction losses, leading to an efficiency of 97.4 percent. This converter seems to have the same capabilities as the Zeta converter, including continuous desired output current and desired buck-boost operation. Such an article offers the operation principle and steady evaluation, as well as a comparison with other existing high step-up configurations. The proposed converter employs a fuzzy logic controller, which improves the voltage level as well as reduces the time taken to set the voltage output of a conventional PI and ANN controller, especially in comparison to the FLC controller. For deployment, Experimental Result and MATLAB/Simulink has been used, and the modeling results indicate that the proposed controller performance has improved

Biofuels have many environmental and practical benefits as a transportation fuel. They are among the best alternatives to fossil fuels due to their capacity for negative carbon emissions, which is vital for archiving the global ambition of a Net-Zero Economy. However, conventional biofuel production takes place on inland sites and relies on freshwater and edible crops (or land suitable for edible crop production), which has led to the food vs fuel debate. It also suffers technical and economical barriers due to the energy balance and the cost of production compared to fossil fuels. Establishing a coastal integrated marine biorefinery (CIMB) system for the simultaneous production of biofuels, high-value chemicals, and other co-products could be the ultimate solution. The proposed system is based on coastal sites and relies on marine resources including seawater, marine biomass (seaweed) and marine microorganisms (marine yeasts and marine microalgae). The system will not require the use of arable land and freshwater in any part of the production chain and will be linked to offshore renewable energy sources to increase its economic and environmental value. This article aims to introduce the CIMB system as a potential vehicle for addressing global warming and speeding the global effort on climate change mitigation as well as increasing global water, food and energy security. I hope this perspective may serve to draw attention into research funding for this approach.

Background: Patients with severe chronic kidney disease (CKD G4-G5) often have chronically elevated high-sensitivity cardiac troponin T (hs-cTnT) values above the 99th percentile of the upper reference limit. In these patients, optimal cutoff levels for diagnosing non-ST-elevation acute cor-onary syndrome (NSTE-ACS) requiring revascularization remain undefined. Methods: Of 11,912 patients undergoing coronary angiography from 2012 to 2017 for suspected NSTE-ACS, 325 (3%) had severe CKD. Of these, 290 with available serial hs-cTnT measurements were included and 300 matched patients with normal renal function were selected as a control cohort. Results: Diagnostic performance for patients with severe CKD was high at presentation and similar to that of the control population (AUC, 95% CI: 0.81, 0.75-0.87 versus 0.85, 0.80-0.89, p=0.68) and the ROC-derived cutoff value at presentation was 4 times higher compared to the conventional 99th percentile. Combining the ROC-derived cutoff levels for hs-cTnT at presentation and absolute 3-hour changes, sensitivity increased to 98%, PPV and NPV improved up to 93% and 86%, re-spectively. (4) Conclusions: In patients with severe CKD and suspected ACS the diagnostic accu-racy of hs-cTnT for the diagnosis of NSTE-ACS requiring revascularization is improved by using higher assay specific cutoff levels combined with early absolute changes.

Growth benefits of high speed rail (HSR) for enterprises are not automatic, but require a buoyant local economy and a robust strategy. Against above background, main objectives of ex-ante case study have been to investigate local socio-economic and spatial impacts of proposed HSR project around Ahmedabad station area on Mumbai-Ahmedabad HSR corridor, analyze the opportunities and challenges of HSR development and draw policy implications. Qualitative research methodology has been used to elicit the perceptions and perspectives of randomly selected 43 small, medium and large enterprises. Data has been analyzed using descriptive statistics. The study reveals that HSR induced greater human interaction will activate local economy, improve business efficiency and generate employment. Frequent travels on business trips can influence enterprises decision to settle near HSR station for easy access and likely to promote realty development. The proposed HSR project should be developed in synergy with urban dynamics of cities in transition and metropolitan service cities. Poor public transport connectivity is likely to be a major challenge in improving HSR accessibility and enhancing overall impacts of HSR, which can be improved by developing an integrated urban transport system, for which cooperation of all stakeholders and coherence with firms’ strategies is essential.

This paper presents two designs of high-efficiency polarizer reflectarray antennas able to generate a collimated beam in dual-circular polarization using a linearly polarized feed, with application to high-gain antennas for data transmission links from a Cubesat. First, an 18 cm x 18 cm polarizer reflectarray operating in the 17.2 - 22.7 GHz band has been designed, fabricated and tested. The measurements of the prototype show an aperture efficiency of 52.7% for right-handed circular polarization (RHCP) and 57.3% for left-handed circular polarization (LHCP), both values higher than those previously reported in related works. Then, a dual-band polarizer reflectarray is presented for the first time, which operates in dual-CP in the frequency bands of 20 and 30 GHz. The proposed antenna technology enables a reduction of the complexity and cost of the feed chain to operate in dual-CP, as a linear-to-circular polarizer is no longer required. This property, combined with the lightweight, flat profile and low fabrication cost of printed reflectarrays, makes the proposed antennas good candidates for Cubesat applications.

This review highlights normal and tumor tissue vasculature, immunological changes, and phenotypic alterations (VIP model) as fundamental in abscopal interaction. In the stereotactic body radiotherapy (SBRT) and immunotherapy era, we are moving toward “immunological radiation planning,” i.e., radiation scheduling with abscopal effect as a vital endpoint as well. Towards this end, this manuscript presents specific diagrammatic tumor models to optimize the outcome of abscopal response in SBRT, based on the principle of the four R’s - Repair, Redistribution, Repopulation, and Reoxygenation of radiotherapy. The article highlights the importance of restricting the dose of SBRT to < 10 Gy per fraction, appropriate use of dose painting, and concomitant/delayed SBRT boost potential. Current literature indicates that immunotherapy should not precede but follow SBRT within seven days. Included is the review of integrating “cyclical” antiangiogenics, immune adjuvants/immune-metabolites as abscopal effect enhancers with SBRT. The importance of proton, carbon-ion SBRT is dealt with briefly. Proposed six fundamental requirements for augmentation of the abscopal cascade are listed. The existing exploratory results need to develop a definitive strategy amidst complex interactions in SBRT, immunotherapy, immune-adjuvants, & abscopal effects. We now have enough literature evidence to convert “abscopal by chance” to “abscopal by design” by harmonized combinatorial approach.

In the last decade, readily available electronic devices have created unprecedented opportunities for teens to access a wide variety of information and media – both positive and negative – on the internet. Despite the increasing number of initiatives taking place worldwide intended to assess and mitigate the online risks encountered by children and adolescents, there is still a need for a better understanding of how adolescents use the internet and what consequences they may face. We conducted a cross sectional online survey of a convenience sample of 733 8th and 9th grade students in Utah. The survey contained eight questions regarding students’ exposure to three types of online risk scenarios: content risk, contact risk, and commercial risk. Independent variables included students’ online behaviors, use of social media and private messaging apps, and adult supervision of online activities. Logistic and negative binomial regression models indicated that female gender, social media use, and chatting with strangers were associated with exposure to multiple unsafe online scenarios. Our results provide critical information to practitioners involved in the development of educational initiatives by building a profile of potentially risky online behaviors and allow them to tailor their initiatives to meet the needs of more vulnerable populations.

In view of the preparation for a post-LHC collider, the high-energy physics (HEP) community started from 2010 to discuss various options, including the use of HTS for very high field dipoles. Therefore, a small program was set in Europe aiming at exploring the possibility of using HTS for accelerator quality magnets. Based on various EU funded programs, though at modest levels, has enabled the European community of accelerator magnets to start getting experience in HTS and addressing a few issues. The program was based on use of REBCO tapes to form 10 kA Roebel cables, to be used to wind small dipoles of 30-40 mm aperture in the 5 T range. The dipoles are designed to be later inserted in a background dipole field (in Nb3Sn), to reach eventually a field level in the 16-20 T range, beyond the reach of LTS. The program is currently underway: more than 1 km tape of high performance (Je &gt; 500 A/mm2 at 20 T, 4.2 K has been manufactured and characterized, various 30 m long Roebel cables have been assembled and validated up to 13 kA, a few dipoles have been wound and tested, reaching at present 4.5 T in stand-alone (while a dipole made from race track coils with no-bore exceeded 5 T using stacked tape cable) and a test in a background field is being organized.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

At different heat treatment temperatures, the hardness and flexural strength of M2 high-speed steel selective laser melting (SLM) parts show mixed trends. When the heat treatment temperature is 260°C, the hardness and flexural strength of the M2 high-speed steel SLM part are decreased, but the hardness difference between the upper and lower surfaces of the M2 high-speed steel SLM part is also reduced. When the heat treatment temperature is 560°C, the hardness and flexural strength of the M2 high-speed steel SLM part are almost close to that of the original M2 high-speed steel SLM part, and the performance gradient in the sample is improved, and the overall structure is uniform. When the subsequent heat treatment temperature is 860 °C, the hardness of the SLM parts reaches a minimum, with an average value of 24 HRC. However, the flexural strength exceeds that of the original SLM parts. Moreover, the microstructure of the sample is uniform, which significantly improves the anisotropy of performance.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

The paper provides information on significant contamination of real laboratory water with hydrophilic microimpurities. This fact suggests that researchers are practically dealing with microdispersed systems. However, this fact is usually neglected in the discussions of the causes of the anomalous properties of water. We will show that, when exposed to various factors of physical nature, water demonstrates reactions of the same type, namely, increased pH and electrical conductivity, reduced redox potential and viscosity, and enhanced bioavailability. Each exposure is accompanied by the destruction of aggregates of the dispersed phase and its transition to a fine-dispersed state. The relationship between this phenomenon and the change in the physicochemical properties of water is discussed.

The origin and significance of the tonalite–trondhjemite–granodiorite (TTG) units and the familiar metabasite xenoliths they host in the Yangtze Craton, China, remain controversial, and resolving these issues is important if we are to understand the evolution of the early Yangtze Craton. We focused on biotite–tremolite schist xenoliths in the Archean TTG units of the Kongling high-grade metamorphic terrane, and U–Pb dating of their zircons yielded ²⁰⁷Pb/²⁰⁶Pb ages of ca. 3.00 Ga, which provides a minimum age for the formation of the pre-metamorphic basic igneous rock. The host TTGs and late intrusive granitic dikes yield three groups of upper intercept ages at 2.87–2.88, 2.91–2.94, and 3.07 Ga, and a concordant age at 2.94 Ga, which suggest that the Yangtze continental nucleus underwent three important metamorphic–magmatic events in the Mesoarchean at ca. 3.00, 2.94, and 2.87 Ga. The biotite–tremolite schists have high ratios of K₂O/Na₂O and high contents of CaO, Cr, and Ni, thus showing the characteristics of high-K calc-alkaline island-arc volcanic rocks (basalt–andesite) that form by the partial melting of subducted oceanic crust. The data also provide further proof that a Mesoarchean metamorphic basement exists in the Yangtze Plate. Derivation of the magmatic protoliths of the biotite–tremolite schist enclaves from an oceanic crust during slab subduction, and the presence of these xenoliths within the TTG suite, indicate the existence of the initiation of plate tectonics during the Mesoarchean (≤2.94 Ga).

We report fabrication of crystalline microresonators of high quality (Q) factors with a controllable wedge angle on lithium niobate on insulator (LNOI). Our technique relies on femtosecond laser assisted chemo-mechanical polish which allows us to achieve ultrahigh surface smoothness as critically demanded by high Q microresonator applications. We show that by refining the polish parameters, Q factors as high as 4.7 × 10⁷ can be obtained and the wedge angle of the LNOI can be continuously tuned from 9° to 51°.

As metabolomics is widely used in the study of disease mechanisms, more and more studies have found that metabolites play an important role in the occurrence of diseases. The aim of this study is to investigate the effects and mechanisms of quercetin in high-fat-sucrose diet (HFD)-induced nonalcoholic fatty liver disease (NAFLD) development using nontargeted metabolomics. A rat model of NAFLD was established by feeding with a HFD for 30 and 50 days. Results indicated quercetin exhibited hepatoprotective activity in HFD-induced NAFLD rats in 30 days by regulating fatty acids related metabolites (adrenic acid, etc.), inflammation related metabolites (arachidonic acid, etc.), oxidative stress related metabolites (2-hydroxybutyric acid) and other differential metabolites (citric acid, etc.). However, quercetin couldn’t improve NAFLD in 50 days maybe it couldn’t reverse the inflammation condition induced by long-term high-fat diet. These data indicate that dietary quercetin may be beneficial to NAFLD at early stages. Furthermore, combining metabolomics and experimental approaches opens up avenues of effects and mechanisms of drugs for complex diseases.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

It was demonstrated during the past decade that ultra-short intense laser pulse tightly focused deep inside a transparent dielectric generates the energy density in excess of several MJ/cm$^3$. Such energy concentration with extremely high heating and quenching rates leads to unusual solid-plasma-solid transformation paths overcoming kinetic barriers to formation of previously unknown high-pressure material phases, which are preserved in the surrounding pristine crystal. These results were obtained with the pulse of Gaussian shape in space and in time. Recently it was shown that the Bessel-shaped pulse could transform much larger amount of a material and allegedly create even higher energy density than that was achieved with the Gaussian (GB) pulses. Here we present a succinct review of previous results and discuss the possible routes for achieving higher energy density employing the Bessel beams (BB) and take advantage of its unique properties.

Wildland fires are responsible for large socio-economic impacts. Fires affect the environment, damage structures, threaten lives, cause health issues, and involve large suppression costs. These impacts can be mitigated via accurate fire spread forecast to inform the incident management team. We show that a fire forecast system based on a numerical weather prediction (NWP) model coupled with a wildland fire behavior model can provide this forecast. This is illustrated with the Chimney Tops II wildland fire responsible for large socio-economic impacts. The system is run at high horizontal resolution (111 m) over the region affected by the fire to provide a fine representation of the terrain and fuel heterogeneities and explicitly resolve atmospheric turbulence. Our findings suggest that one can use the high spatial resolution winds, fire spread and smoke forecast to minimize the adverse impacts of wildland fires.

Human factors are the most relevant issues contributing to adverse events in obstetrics. Specific training of Crisis Resource Management (CRM) skills (i.e., problem solving and team management, resource allocation, awareness of environment, and dynamic decision-making) are now widespread and are often based on High Fidelity Simulation. In order to be used as a guideline in simulated scenarios, they need to be translated into specific and observable behavioral markers. To this purpose, we developed a set of observable behaviors related to the main elements of CRM in the delivery room. The observational tool was then adopted in a two-days seminar on obstetric hemorrhage where teams working in obstetric wards of six Italian hospitals took part to simulations. The tool was used as guide for the Io and as a peer-to-peer feedback. It was then rated for its usefulness in facilitating the reflection upon one’s own behavior, its ease of use, and its usefulness for the peer-to-peer feedback. The ratings were highly positive, around 4 in a 5-point scale. The CRM observational tool is therefore a useful, quick and easy solution to facilitate the debriefing, the peer-to-peer feedback and, most of all, the transfer of safe behavior from simulation to everyday practice.

Background: Studies employing next-generation sequencing (NGS) show that the oral fungal community (mycobiome) is far more complex than hitherto thought. However, the role of the oral mycobiome in health and disease, including oral carcinogenesis, has not been explored. Objective: To characterize the mycobiome associated with oral squamous cell carcinoma (OSCC). Methods: Tissue biopsies [cases: 25 OSCC; controls: 27 intra-oral fibro-epithelial polyp (FEP)] were collected from oral and maxillofacial units in Sri Lanka. Total DNA was extracted and subjected to sequencing of the fungal ITS2 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a BLASTN-algorithm with UNITE’s named species sequences as reference. Downstream analyses were performed using QIIME and LEfSe. Results: 364 species representing 160 genera and 2 phyla (Ascomycota and Basidiomycota) were identified, with Candida and Malassezia making up 48% and 11% of the average mycobiome, respectively. However, only 5 species and 4 genera were detected in ≥50% of the samples. The species richness and diversity were significantly lower in OSCC. At the genus level, Candida, Hannaella and Gibberella were overrepresented in OSCC while Alternaria and Trametes were more abundant in FEP. Species-wise, C. albicans, C. etchellsii and Hannaella luteola-like species were enriched in OSCC while Malassezia restricta, Aspergillus tamarii, Alternaria alternate, Cladosporium halotolerans, and Hanseniaspora uvarum-like species were the most significantly abundant in FEP. Conclusions: A dysbiotic mycobiome dominated by C. albicans was found in association with OSCC. Whether this dysbiosis plays a role in oral carcinogenesis warrants further investigation.

Studies on the possible association between bacteria and oral squamous cell carcinoma (OSCC) remain inconclusive, largely due to methodological variations/limitations. The objective of this study was to characterize the species composition as well as functional attributes of the bacteriome associated with OSCC. DNA obtained from 20 fresh OSCC biopsies (cases) and 20 deep-epithelium swabs (matched control subjects) were sequenced for the V1-V3 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a prioritized BLASTN-algorithm. Downstream analyses were performed using QIIME, PICRUSt, and LEfSe. Fusobacterium nucleatum subsp. polymorphum was the most significantly overrepresented species in the tumors followed by Pseudomonas aeruginosa and Campylobacter sp. Oral taxon 44, while Streptococcus mitis, Rothia mucilaginosa and Haemophilus parainfluenzae were the most significantly abundant in the controls. Functionally, genes involved in bacterial mobility, flagellar assembly, bacterial chemotaxis and LPS synthesis were enriched in the tumors while those responsible for DNA repair and combination, purine metabolism, phenylalanine, tyrosine and tryptophan biosynthesis, ribosome biogenesis and glycolysis/gluconeogenesis were significantly associated with the controls. This is the first epidemiological evidence for association of F. nucleatum and P. aeruginosa with OSCC. Functionally, an “inflammatory bacteriome” is enriched in OSSC.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

Originally developed to image the shadow region of the central black hole in Sagittarius A* and in the nearby galaxy M87, the Event Horizon Telescope (EHT) provides deep, very high angular resolution data on other AGN sources too. The challenges of working with EHT data have spurred the development of new image reconstruction algorithms. This work briefly reviews the status of the EHT and its utility for observing AGN sources, with emphasis on novel imaging techniques that offer the promise of better reconstructions at 1.3 mm and other wavelengths.

There is an increasing need for compact low-cost NMR apparatus that can be used on the laboratory bench and in the field. There are four main usage variants of usage: a) Time-Domain apparatus, particularly for physical measurements; b) Frequency Domain apparatus, particularly for chemical analysis, c) NMR Cryoporometry apparatus for measuring pore-size distributions, and d) MRI apparatus for imaging. For all of these, variable temperature capability may be vital. We have developed compact low-cost apparatus targeted at these applications. We discuss a hand-held size NMR spectrometer, and three different holdable NMR magnets, with sufficiently large internal bores for the Lab-Tools compact Peltier thermo-electric cooled variable-temperature probes. Currently the NMR Spectrometer is very suitable for a), NMR time-domain relaxation and c), NMR Cryoporometry. With a suitable high-homogeneity magnet it is also appropriate for simple use b), spectral analysis, or, with a suitable gradient set, use d), MRI. Together, the NMR Spectrometer, one of the NMR variable-temperature probes, and any of these NMR magnets make an excellent NMR Cryoporometers, as demonstrated by this paper, and previously published research. Equally, they make versatile general-purpose variable-temperature NMR systems for materials-science.

Analyzing the impacts of urban landscape patterns on the thermal environment has become one of the key research areas in addressing urban heat islands (UHI) and improving the living environment. A case study was carried out in Fuzhou, Fujian Province of China, to quantify the spatial patterns of urban landscape and land surface temperature (LST) in different development areas. The contribution of the thermal environment and the factors influencing the heterogeneity of LST were analyzed and discussed. In this study, bi-temporal Landsat imagery was selected to calculate LST, percent impervious surface area (ISA), and fractional vegetation cover (FVC). The urban area was further divided into three concentric urban zones, ranging from the city center to the urban periphery, based on urban development densities. The spatial pattern of LST and its variance were analyzed and compared between different zones and different dates. The thermal environment contribution of different zones was also quantified to indicate the change in urban landscape pattern resulting from urban expansion in different zones. Furthermore, Geodetector was used to explore the single factors and interaction factors controlling the spatial patterns of LST in each zone. The results showed that (ⅰ) Urban expansion primarily increased in zone 2 and zone 3, and the areal proportion of high and sub-high LST areas increased from 56.11% and 21.08% to 62.03% and 32.49% in zone 2 and zone 3, respectively, from 2004 to 2021; (ⅱ) The heat effect contribution of zones 2 and 3 reached from 75.16% in 2004 to 89.40% in 2021, indicating that the increase of ISA with >LSTmean was more pronounced in zone 3 and zone 2 during the period; (ⅲ) The driving factors of LST spatial distribution were regionally different because of the different landscape patterns, and the explanatory power for the heterogeneity of LST in zone 1 was weaker than that in zone 2 and zone 3 in the study area; (ⅳ) The interaction of different factors had a higher explanatory power on the spatial distribution of LST than a single factor in each zone because the distributions of land cover types are heterogeneous in urban area. The results of the study can be used to improve urban planning for urban ecology and UHI mitigation.

While the simple model of the total atmospheric carbon sink effect as a linear function of concentration has provided excellent prediction results, several problems remained to be investigated and solved. The most obvious open issue is the correct treatment of land use change emssions. It turns out that the model improves by mostly neglecting them after 1959. This effectively implies that land use change emissions have been constant and small since then. The key investigation starts with the observation, that the total carbon sink has a short term component which be explained by temperature changes commonly known as El Nin˜o. The apparent paradox is analysed and explained, why contrary to the short term changes no temperature caused trend can be detected in the model, despite the fact that several contributing processes exhibit temperature dependency. The result of this analysis leads to the model extension, where the total effect of sinks and natural emissions are a linear function of concentration and temperature. This model not only explains current measurements but also paleo climate from ice-core time series.

Transition metal complexes have historically played a pivotal role in creating vibrant pigments utilized across artistic mediums such as ceramics, paintings, and glass mosaics. Despite their extensive historical use, our understanding of the mechanisms governing transition metal complex behavior has predominantly emerged in recent times, leaving numerous aspects of this process ripe for exploration. These complexes exhibit striking color variations under diverse conditions when employed in pigment formulations. This review utilizes a bottom-up scientific approach, spanning from microscopic to macroscopic scales, to unravel the molecular origins of the colors generated by transition metal complexes in pigments and ceramic glazes. Advanced spectroscopy techniques and computational chemistry play pivotal roles in this endeavor, highlighting the significance of understanding and utilizing analytical data effectively, with careful consideration of each technique's specific application. Furthermore, the review investigates the influence of processing conditions on color variations, providing valuable insights for artists and manufacturers aiming to enhance the precision and quality of their creations while mitigating environmental impact.

Recent satellite measurements of glacier mass balance show mountain glaciers all over the world had generally negative mass balances in the first decades of the 21st century. Mean summer temperatures all over the world rose from 1961-90 to 1991-2020, implying increasingly negative mass balances. We study archived annual balances for 38 Northern Hemisphere glaciers to assess changes within in the 19612020 period. We use a modified doublemass curve to visualize mass balance changes occurring around 1990. Mean balances 196190 were already small negative for many of the studied glaciers and became even more negative in 19912020 for glaciers in the Alps, at high latitudes and in western North America. The largest mass balance changes are for some glaciers in the Alps. We are unable to explain the lack of change in mean balance for one glacier in High Mountain Asia. We find complex changes for eight glaciers in Scandinavia, even including one glacier with positive balance. We explain these changes by visualizing deviations of winter and summer balances from their respective 1961-90 mean values. High winter balances in the 1990s for Scandinavia partly obscured the emerging trend of increasingly negative summer balances, which we expect to continue in the future.

India ranks among the top ten nations in the world for grape production. Fungal pathogens inflict damage to crop plants in turn making cultivators bear huge economical losses. With an output of 1.21 million tons (about 2% of 57.40 million tons produced globally). 1.2% of the nation’s total fruit cropland is covered by grapes. But due to fungal diseases the effect of the yield produced ranges from 5-80% depending on the severity of diseases which will affect the yield of grape vineyard. In precision agriculture, new sensing technologies and artificial intelligence could be used to automatically identify grapevine and disease pest symptoms. Traditional manual disease-monitoring methods are inefficient, labor-intensive, and ineffective. Timely effective and precise evaluation of grape diseases is admitted as a critical step in the field management. In this paper, we are explaining about different optical sensing methods applied for RGB, Multispectral and Thermal cameras. Section-wise we will be describing environmental set up for image-aquation, data-preprocessing, different modelling methods, evaluation matrix, result, and reviewer’s comment.

Accurate climate data at fine spatial resolution are essential for scientific research and the development and planning of crucial social systems, such as energy and agriculture. Among them, sea surface temperature plays a critical role as the associated El Niño-Southern Oscillation (ENSO) is considered a significant signal of global interannual climate system. In this paper, we propose an implicit neural representation-based interpolation method with temporal information (T_INRI) to reconstruct climate data of high spatial resolution, with sea surface temperature as the research object. Traditional deep learning models for generating high-resolution climate data are only applicable to fixed resolution enhancement scales. In contrast, the proposed T_INRI method is not limited to the enhancement scale provided during the training process and its results indicate that it can enhance low-resolution input by arbitrary scale. Additionally, we discuss the impact of temporal information on the generation of high-resolution climate data, specifically, which month the low-resolution sea surface temperature data is from. Our experimental results indicate that T_INRI is advantageous over traditional interpolation methods under different enhancement scales, and the temporal information can improve T_INRI performance for a different calendar month. We also examined the potential capability of T_INRI in recovering missing grid value. These results demonstrate that the proposed T_INRI is a promising method for generating high-resolution climate data and has significant implications for climate research and related applications.

Upper mesophilic temperature acclimation of halophilic, hydrogen-producing bacteria from salt fields was investigated in this study, along with the changes in microbial abundance during an-aerobic digestion (AD) process. Genomic approaches such as PCR-denaturing gradient gel elec-trophoresis (DGGE) and next-generation sequencing (NGS) were performed to profile the mi-crobial communities. During AD, there was a significant abundance of Halanaerobacter lacunarum at 48°C followed by the increase in hydrogen yield, signifying potential contribution from the halophile in the hydrogen production. A decrease in the dominance of H. lacunarum and Halan-aerobium fermentans at 42°C, likely due to an increase in other bacterial species, was noted but their dominance significantly increased at temperatures of 45°C and 48°C. This investigation provides valuable insights in highlighting the potential of Halanaerobium sp. and the other halo-philic bacteria to adapt under upper mesophilic temperature conditions and synthesizing hy-drogen. The findings in the present study also underscore the importance of optimizing temper-ature and pH conditions to maximize hydrogen yield during high-salt anaerobic digestion.

Climate change is expected to result in rising temperatures, leading to increased occurrences of extreme weather events like heat waves and cold spells. Urban planning responses are crucial for improving the adaptive capacity of cities and communities in dealing with significant temperature variations across seasons. This study aims to investigate the relationship between urban temperature fluctuations and urban morphology throughout the four seasons. Through quadrant and statistical analyses, the study identifies built-environment factors that contribute to moderate seasonal land surface temperatures (LST). The research focuses on Seoul, South Korea as a case study and calculates seasonal LST values at both the grid level (100m×100m) and street-block level, incorporating factors such as vegetation density, land use patterns, albedo, two- and three-dimensional building forms, and gravity indices for natural reserves. The quadrant analysis reveals spatial segregation between areas demonstrating high LST adaptability (cooler summers and warmer winters) and those displaying LST vulnerability (hotter summers and colder winters), with significant differences in vegetation and building forms. The spatial regression analysis demonstrates that higher vegetation density and proximity to water bodies play key roles in moderating LST, leading to cooler summers and warmer winters. Building characteristics have an invariant impact on LST across all seasons, where horizontal expansion contributes to higher LST, while vertical expansion reduces LST. These findings are consistent for both grid- and block-level analyses. The study emphasizes the flexible role of the natural environment in moderating temperatures.

A distinction is made between data rescue (i.e., copying, digitizing and archiving) and data recovery that implies deciphering, interpreting and transforming early instrumental readings and their metadata to obtain high-quality datasets in modern units. This requires a multidisciplinary approach that includes: palaeography and knowledge of Latin and other languages to read the handwritten logs and additional documents; history of science to interpret the original text, data e metadata within the cultural frame of the 17th, 18th and early 19th century; physics and technology to recognize bias of early instruments or calibrations, or to correct for observational bias; astronomy to calculate and transform the original time in canonical hours that started from twilight. The liquid-in-glass thermometer was invented in 1641 and the earliest temperature records started in 1654. Since then, different types of thermometers were invented, based on the thermal expansion of air or selected thermometric liquids with deviation from linearity. Reference points, thermometric scales, calibration methodologies were not comparable, and not always adequately described. Thermometers had various locations and exposures, e.g., indoor, outdoor, on windows, gardens or roofs, facing different directions. Readings were made only one or a few times a day, not necessarily respecting a precise time schedule: this bias is analysed for the most popular combinations of reading times. The time was based on sundials and local Sun, but the hours were counted starting from twilight. In 1789-90 Italy changed system and all cities counted hours from their lower culmination (i.e., local midnight), so that every city had its local time; in 1866, all the Italian cities followed the local time of Rome; in 1893, the whole Italy adopted the present-day system, based on the Coordinated Universal Time and the time zones. In 1873, when the International Meteorological Committee (IMO) was founded, later transformed in World Meteorological Organization (WMO), a standardization of instruments and observational protocols was established, and all data became fully comparable. In the early instrumental period, from 1654 to 1873, the comparison, correction and homogenization of records is quite difficult, mainly because of the scarcity or even absence of metadata. This paper deals about this confused situation, discussing the main problems, but also the methodologies to recognize missing metadata, distinguish indoor from outdoor readings; correct and transform early datasets in unknown or arbitrary units into modern units; finally, in which cases it is possible to reach the quality level required by WMO. The focus is to explain the methodology needed to recover early instrumental records, i.e., the operations that should be performed to interpret, correct, and transform the original raw data into a high-quality dataset of temperature, usable for climate studies.

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

The availability of sufficient amounts of form I of benzocaine has led to the investigation of its phase relationships with the other two existing forms II and III using adiabatic calorimetry, powder X-ray diffraction, and high-pressure differential thermal analysis. The latter two forms were known to have an enantiotropic phase relationship with form III stable at low-temperature and high-pressure, while form II is stable at room temperature. Using adiabatic calorimetry data, it can be concluded, that form I is the stable low-temperature, high-pressure form, which also happens to be stable at room temperature; however, form II, due to its persistence at room temperature, is still the most convenient polymorph to use in formulations. Form III presents a case of overall monotropy and does not possess any stability domain in the pressure-temperature phase diagram. Heat capacity data for benzocaine have been obtained by adiabatic calorimetry from 11 K up to 369 K above its melting point, which can be used to compare to results from in-silico crystal structure prediction.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

Residual stresses in fiber metal laminates (FML) inevitably develop during the manufacturing process. The main contributor to these stresses is the difference in the coefficients of thermal expansion (CTE) between fibers and metal in combination with high process temperatures. To quantify these stresses, the use of specimens with an asymmetric layup is an easily adaptable method. The curvature that develops after the manufacturing of flat laminates with an asymmetrical layer stack is a measure of the level of residual stresses evolving during cure. However, the accuracy of the curvature evaluation is highly dependent on specimen design and other influencing parameters. In this work a large set of FML specimens is investigated to identify relevant influencing parameters and derive conclusions about specimen design and evaluation techniques. For certain layups and process parameters, there is a good correlation between the curvature and the stress-free temperature, which is further covered by analytical solutions for bimetals. This correlation is the basis to transfer curvature into a stress-free temperature that can consequently be used for the quantification of residual stress levels in more complex FMLs. The transfer is validated by in-situ strain measurements during cure using a strain gage technique. Based on the results, the application of asymmetric specimens for residual stress characterization in more complex laminates is presented in the form of a workflow.

This study examined the association between pressure injuries and complexity of abdominal temperature measured in residents of a nursing facility. The temperature served as a proxy measure for skin thermoregulation. Refined multiscale sample entropy and bubble entropy were used to measure the complexity of the temperature time series measured over two days at 1-minute intervals. Robust summary measures were derived for the multiscale entropies and used in predictive models for pressure injuries that were built with adaptive lasso regression and neural networks. Both types of entropies were lower in the group of participants with pressure injuries (n=11) relative to the group of non-injured participants (n=15). This was generally true at the longer temporal scales, with the effect peaking at scale τ=23 minutes. Predictive models for pressure injury on the basis of refined multiscale sample entropy and bubble entropy yielded 92% accuracy, outperforming predictions based on any single measure of entropy. Combining entropy measures with a widely used risk assessment score led to the best prediction accuracy. Complexity of abdominal temperature series could therefore serve as an indicator of risk of pressure injury.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

The present paper proposes a fractal analysis of the Covid-19 dynamics in 45 European countries. We introduce a new idea of using the box-counting dimension of the epidemiologic curves as a means of classifying the Covid-19 pandemic in the countries taken into consideration. The classification can be a useful tool in deciding upon the quality and accuracy of the data available. We also investigated the reproduction rate, which proves to have significant fractal features, thus enabling another perspective on this epidemic characteristic. Moreover, we studied the correlation between two meteorological parameters: global radiation and daily mean temperature and two Covid-19 indicators: daily new cases and reproduction rate. The fractal dimension differences between the analysed time series graphs could represent a preliminary analysis criterion, increasing research efficiency. Daily global radiation was found to be stronger linked with Covid-19 new cases than air temperature (with a greater correlation coefficient -0.386, as compared with -0.318), and consequently it is recommended as the first-choice meteorological variable for prediction models.

Mushrooms have long rich history in folk medicine, traditional and functional foods due to high content of dietary myco-nutrients. Currently, there is increased interest in finding appropriate food-grade green ex-traction systems capable of extracting these bioactive compounds from dietary mushrooms for applica-tions in various food, pharmacological or nutraceutical formulations. Herein, we evaluated a modified Swiss water process (SWP) method using alkaline and acidic pH at low and high temperature under pressurized conditions as a suitable green food grade solvent to obtained extracts enriched with my-co-nutrients (dietary phenolics, total antioxidants (TAA), vitamins, and minerals) from Chaga. Ultra-high performance liquid chromatography coupled to high resolution accurate mass tandem mass spectrometry (UHPLC-HRAMS-MS/MS) was used to assess the phenolic compounds and vitamin levels in the extracts, while inductively coupled plasma mass spectrometry (ICP-MS) was used to determine the mineral con-tents. Over twenty phenolic compounds were quantitatively evaluated in the extracts and the highest total phenolic content and antioxidant activity was observed at pH11.5 at 100°C. The most abundant phenolic compounds present in Chaga extracts included phenolic acids such as protocatechuic acid 4-glucoside (0.7-1.08µg/mL), syringic acid (0.62-1.18µg/mL), and myricetin (0.68-1.3µg/mL). Vitamins are being reported for the first time in Chaga. pH 2.5 at 100°C treatment shows superior effects in extracting the B vitamins whereas pH 2.5 at 60 and 100°C treatments were outstanding for extraction of total fat-soluble vitamins. Vitamin E content was the highest for the fat-soluble vitamins in the Chaga extract under acidic pH (2.5) and high temp. (100°C) and ranges between 50 to 175 µg/100g Chaga. Antioxidant minerals ranged from 85.94 µg/g (pH7 at 100°C) to 113.86 µg/g DW (pH2.5 at 100°C). High temperature 100°C and a pH of 2.5 or 9.5. The treatment of pH11.5 at 100°C was the most useful for recovering phenolics and antioxidants from Chaga including several phenolic compounds reported for the first time in Chaga. SWP is being proposed herein for the first time as a novel, green food-grade solvent system for the extraction of myco-nutrients from Chaga and have potential applications as a suitable approach to extract nutrients from other matrices. Chaga extracts enriched with bioactive myconutrients and antioxidants may be suitable for further use or applications in the food and nutraceutical industries.

The combined effects of global warming and increasing urban heat islands (UHIs) on air temperature and heat stress in cities are notable physical and mental health implications for citizens. With research having shown the effective role of urban green spaces in decreasing urban heat, this study investigated the cooling effect of a large urban park on thermal comfort outside the park area, from psychological and physiological perspectives. The studied park is located in the center of Madrid and adjacent to UHI. The study was performed by conducting field measurements and a survey with questionnaires. The measurements made on six summer days (with two-week intervals) showed that the park’s cooling effect could decrease the air temperature by 2.4-2.8°C right up to the edge of the heat island (600m), and decrease the physiological equivalent temperature (PET) by about 3.9°C. By decreasing air temperature and PET, this park was also shown to increase the perceived thermal comfort (PTC) of the citizens from the psychological perspective in the defined area of effect. This perceived thermal comfort was found to have a significant inverse relationship with PET (P-value <0.05). The examination of cognitive maps drawn by citizens showed that out of the 145 respondents, 68.3% marked the park as the area that they perceive as having the greatest thermal comfort, and prefer as the place to spend time enjoying thermal comfort, irrespective of its distance from their location.

New modi ed Hayward metric of magnetically charged non-singular black hole spacetime in the framework of nonlinear electrodynamics is constructed. When the fundamental length introduced, characterising quantum gravity effects, vanishes one comes to the general relativity coupled with the Bronnikov model of nonlinear electrodynamics. The metric can have one (an extreme) horizon, two horizons of black holes, or no horizons corresponding to the particle-like solution. Corrections to the Reissner-Nordström solution are found as the radius approaches to in nity. As r -> 0 the metric has a de Sitter core showing the absence of singularities. The asymptotic of the Ricci and Kretschmann scalars are obtained and they are nite everywhere. The thermodynamics of black holes, by calculating the Hawking temperature and the heat capacity, is studied. It is demonstrated that phase transitions take place when the Hawking temperature possesses the maximum. Black holes are thermodynamically stable at some range of parameters.

This article presents a new theory on redshift of light from celestial bodies. Lately it has been found that the Hubble constant calculated from different methods discord so much that calls arise for new physics to explain. Also, in addition to many unsolved puzzles like dark matter and source of expansion force, we shall show in this article that the current theory of redshift implies a few hidden, unreasonale assumptions. By assuming photon has temperature and its thermal energy is fully converted to wave energy, this article shows that photon can have a new redshift called Temperature Redshift, which not only is more significant for remote stars or galaxies, but also better fits the observational data, including those used in Hubble constant calculation. As such, if true, this new theory not only adds to our new understanding of photons, but may totally change our current understanding of the Universe, i.e., the Big Bang theory.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Single-confinement housing can pose welfare risks to domestic horses. This study investigated horses’ stress responses when confined to single stalls in different stable designs in a tropical savanna region to address a literature gap. In total, 23 horses were assigned to a stable with a central corridor and solid external walls (A) (N = 8), a stable with one side corridor and solid external walls (B) (N = 6) or a stable with a central corridor and no solid external walls (C) (N = 9). Air velocity, relative humidity, air temperature and noxious gases were measured inside the stables, and the heart rate and HRV of the horses were also determined. The relative humidity was lower in stable C than in stable A (p &lt; 0.05), while the air temperature was higher in stable C than in stable B (p &lt; 0.05) during the day. The airflow and ammonia levels were higher in stable C than in stables B and A (p &lt; 0.01–0.0001). Overall, horses’ HRV in stable A was lower than in those in stables B and C (p &lt; 0.05-0.01). Horses in stable A tended to experience more stress than those in other stables.

We have investigated the influence of the relative proportions of glass formers in a series of lithium alumino-borosilicate glasses with respect to electrical conductivity () and glass transition temperature (Tg) as functions of glass structure, as determined by Raman spectroscopy. The ternary lithium alumino-borate glass exhibits the highest  and lowest Tg among all the compositions of the glass series, 30Li2O•3Al2O3• (67-x) B2O3•xSiO2. However, as B2O3 is replaced by SiO2, a shallow minimum in  as well as a shallow maximum in Tg are observed near x = 27, where the Raman spectra indicate isolated diborate/tetraborate/orthoborate groups are being progressively replaced by danburite/reedmergnerite-like borosilicate network units. Overall, as the glasses become silica-rich,  is minimized, while Tg is maximized. In general, these findings show correlations among Tg, (sensitive to network polymerization),  (proportional to ionic mobility), and the different borate and silicate glass structural units as determined by Raman spectroscopy. X-ray diffraction analyses demonstrate the absence of appreciable crystallinity in the glasses investigated. However, scanning electron microscopy (SEM) images of HF-etched samples showed that glasses, and especially the borate-rich compositions comprise two distinct glassy phases. The isolated phase is 25-100 nm in diameter, dispersed evenly in a glassy matrix.

In this experiment, the fermented pineapple residue (FPR) was replaced with 0% (CON), 25% (T25) and 50% (T50) in the diet based on silage royal grass roxb for 30 days in the fattened fatten bulls to evaluate the effect of FPR on growth performance, serum indicators and rumen characteristics.Thirty Simmental calves were selected and divided into three groups according to a completely random design.The temperature and humidity of the cowshed shall be measured every day.Rectal temperature and blood of cattle were measured, and blood and immune markers were measured.The results showed that the rectal temperature decreased significantly when adding 25% fermented pineapple residue (P&lt;0.05), and the rectal temperature decreased significantly when adding 50% fermented pineapple residue (P&lt;0.01).The content of T4 and TC in serum of cattle in T50 group was significantly lower than that in the control group (P&lt;0.01), and the content of T3 was significantly higher than that in the control group (P&lt;0.05), and the content of CR was significantly lower than that in the control group (P&lt;0.01). Fermented pineapple residue can indeed improve the oxidative (heat) stress resistance of finishing cattle. In the correlation experiment, bacterial genera such as Succinniclassicum, Melainabacteria, Lachnospiraceae, and Fibrobacteres all showed significant or extremely significant correlations with heat stress-related indicators.

The study used ERA5 reanalysis SST dataset re-gridded to a common grid of 0.25° X 0.25° spatial resolution (latitude × longitude) for the historic (1940–2014) and projected (2015–2100). The SST simulation under the SSP5-8.5 scenarios was carried out with output from 8 General Circulation Models (GCMs). The bias-corrected dataset was developed using Empirical Quantile Mapping EQM for the historical (1940-2015) and the future (2030-2100) while the CMIP6 model simulation was evaluated against the ERA5 monthly rainfall observed data for monthly and annual sea surface temperatures (SST) over the Gulf of Guinea. ). The CMIP6 models simulation for SST projection from 2030-20100 based on SSPS 8.5 SST is projected to increase by 4.61o (31oC) in 2030 to 35oC in 20100 in the coastal GOG and 2.6oC in the Western GOG (Sahel). The correlation coefficient (r) was used to evaluate the performance of the CMIP6 models and the analysis showed ACCESS 0.1,CAMS CSM 0.2, CAN ESM 0.3, CMCC, 0.3 and MCM, 0.4 indicating that all models performed well in capturing the climatological pattern of the SST. The.CMIP6 bias corrected model simulations showed increased SST warming over the GOG will be higher in the Far period end than the Near-term climate. The study affirmed that the CMIP6 projections can be used for multiple assessments related to climate and hydrological impact studies and for the development of mitigation measures under a warming climate

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

Land Surface Temperature (LST) estimation has been studied for several purposes, while the optimal method of estimating the LST has not been criticized yet. This research explores the optimum method in Land Surface Temperature (LST) estimation using LANDSAT-8 imagery data. Four different LST retrieval approaches, the Radiative Transfer Equation-based method (RTE), the Improved Mono-Window method (IMW), the Generalized Single-Channel method (GSC), and the Split-Window algorithm (SW), were calculated to present the LSTs over Buriram Town Municipality, Thailand. The calculated LSTs from these four methods were compared with the ground-based temperature data, taken on the same date and time of the employed LANDSAT-8 images. For this reason, the optimum method of the LST calculation was justified by considering the lowest normalized root means square error (NRMSE) values. As a result, the SW algorithm presents an optimum method in LST estimation. Regarding the SW, this algorithm requires not only the atmospheric profiles during satellite acquisition but also the retrieval of several coefficients. Besides, the LST retrieval method based on the SW algorithm is sensitive to water vapor content and coefficients. Although the SW algorithm is an optimum method explored in this study, it is emphasized that the adjustable values of coefficient response to the atmospheric state may be recommended. With these conditions, the SW algorithm can generate the land-surface temperature over the mixed land-use and land cover on the LANDSAT-8 images.

The classical approach to non-linear regression in physics, is to take a mathematical model describing the functional dependence of the dependent variable from a set of independent variables, and then, using non-linear fitting algorithms, extract the parameters used in the modeling. Particularly challenging are real systems, characterised by several additional influencing factors related to specific components, like electronics or optical parts. In such cases, to make the model reproduce the data, empirically determined terms are built-in the models to compensate for the impossibility of modeling things that are, by construction, impossible to model. A new approach to solve this issue is to use neural networks, particularly feed-forward architectures with a sufficient number of hidden layers and an appropriate number of output neurons, each responsible for predicting the desired variables. Unfortunately, feed-forward neural networks (FFNNs) usually perform less efficiently when applied to multi-dimensional regression problems, that is when they are required to predict simultaneously multiple variables that depend from the input dataset in fundamentally different ways. To address this problem, we propose multi-task learning (MTL) architectures. These are characterized by multiple branches of task-specific layers, which have as input the output of a common set of layers. To demonstrate the power of this approach for multi-dimensional regression, the method is applied to luminescence sensing. Here the MTL architecture allows predicting multiple parameters, the oxygen concentration and the temperature, from a single set of measurements.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.

Objectives: To rate the effects of low molecular weight hyaluronic acid (LMWHA) solution and high concentration oxygen (HCO) through a specific medical device (Caress Flow©), compared to topical administration of hyaluronic acid (HA) alone on symptoms of mild and moderate stress and mixed urinary incontinence in women with genitourinary syndrome of menopause (GSM). Methods: A total of 68 postmenopausal women were enrolled (from October 2021 to September 2023). Patients were separated in two groups: one group used therapy with LMWHA solution and HCO combined and the second group used therapy with HA alone. Patient Global Impres-sion of Improvement (PGI-I) as the first outcome was used. As secondary outcomes International Consultation on Incontinence Questionnaire - short form (ICIQ-SF) questionnaire and Internation-al Quality of Life (IQoL) questionnaire were used. Results: Sixty-eight (68) women, 35 (51%) and 33 (49%), were treated with LMWHA solution and HCO combined and HA alone for 10 weeks, respectively. 28 (80%) versus 7 (20%) women reported an improvement (PGI-I score ≤3) of the symptoms in LMWHA solution and HCO com-bined group versus HA alone group. According to the ICIQ-SF, a statistically significant differ-ence was recorded after treatment between the two groups (median, 7 [5-11] vs 10 [8-11]; P = 0.03). According to the IQoL questionnaire, a statistically significantly lower median score was recorded in the LMWHA solution and HCO combined compared with the HA group, before (71 [IQR 55-81] vs 89 [IQR 67-94]; P < 0.01) and after (78 [IQR 65-86] vs 88 [IQR 72-99]; P = 0.04) treatment. Conclusions: LMWHA solution and HCO combined might improve the mild and moderate stress and mixed urinary incontinence in this set of women and that it is superior to HA therapy alone. However, these results need to be confirmed in further studies with a controlled design and a larger population.

Aligning supply chain and marketing functions is crucial for high-tech startups aiming to successfully launch new products in competitive markets. This qualitative research explores the strategies, challenges, benefits, and best practices associated with supply chain and marketing alignment in high-tech startups. Through a detailed analysis of case studies and semi-structured interviews with industry professionals, the study identifies key insights into how startups can effectively integrate these functions to enhance operational efficiency, market responsiveness, customer satisfaction, and risk management. The findings reveal that successful alignment requires the formation of cross-functional teams, leveraging integrated technologies like CRM and ERP systems, establishing regular inter-departmental communication, and developing joint performance metrics. These strategies foster collaboration and ensure that supply chain and marketing efforts are coordinated towards shared goals. However, startups face challenges such as differing departmental objectives, resource constraints, communication barriers, and technological limitations, which hinder effective alignment. Benefits observed from effective alignment include improved operational efficiency through streamlined processes, enhanced market responsiveness to adapt quickly to changing demands, increased customer satisfaction by delivering products that meet market expectations, and better risk management through proactive identification and mitigation of supply chain and market risks. Best practices identified include fostering a culture of collaboration, investing in technology for data integration and transparency, aligning strategic objectives across functions, and continuously monitoring and adjusting alignment strategies. Integration of broader elements such as sustainability, entrepreneurship, emotional intelligence, marketing, and supplier relationship management further enriches the alignment framework. This study contributes to a deeper understanding of how high-tech startups can strategically align their supply chain and marketing functions to achieve competitive advantage and sustainable growth in dynamic market environments.

Gradients of smooth functions with non-independent variables are relevant for exploring complex models and for the optimization of functions subjected to constraints. In this paper, we investigate new and simple approximations and computations of such gradients by making use of independent, central and symmetric variables. Such approximations are well-suited for applications in which the computations of the gradients are too expansive or impossible. The derived upper-bounds of the biases of our approximations do not suffer from the curse of dimensionality for any $2$-smooth function, and theoretically improve the known results. Also, our estimators of such gradients reach the optimal (mean squared error) rate of convergence (i.e., $\mathcal{O}(N^{-1})$) for the same class of functions. Numerical comparisons based on a test case and a high-dimensional PDE model show the efficiency of our approach.

Evaluation of drug permeability using cell monolayers is an important in vitro assay in the process of drug development, to identify compounds with favourable pharmacokinetics that may proceed to in vivo studies. When allowed to differentiate on permeable filters for at least 21 days, monolayers of Caco-2 cells develop morphological and functional properties similar to those of the intestinal epithelium. Permeability through Caco-2 monolayers is thus particularly relevant to assess drug absorption after oral administration. The major drawback of this assay is its very low throughput, with the cell monolayers being used in a single permeability assay. We have previously proposed a protocol to allow the re-use of the Caco-2 monolayer on additional permeability assays during the stable period and shown that cell monolayer integrity is maintained. In this work we evaluate the effect of re-use on the permeability of several reference compounds that permeate through passive pathways and show that the cell monolayers can be re-used twice in additional permeability assays. Preliminary results were also obtained regarding active transport pathways, and a new methodology is proposed to quantify the contribution from passive and active transport. This is a major step towards the full validation of the re-use methodology proposed, which at least triplicates the throughput of this important in vitro assay.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

p-type Ag-N dual acceptor doped ZnO thin films with long electrical stability were deposited by DC magnetron reactive co-sputtering technique. After deposition, the films were annealed at 400 °C for one hour in a nitrogen-controlled atmosphere. The deposited films were amorphous. However, after annealing they crystallize in the typical hexagonal wurtzite structure of ZnO. The Ag-N dual acceptors were incorporated substitutionally in the structure of zinc oxide and achieving that the three samples presented the p-type conductivity in the ZnO. Initial electrical properties showed a low resistivity of from 1 to10^{−3} Ω.cm, Hall mobility of tens cm2/V.s and a hole concentration from 10^{17} to 10^{19} cm^{−3}. The electrical stability analysis reveals that the p-type conductivity of the ZnO:Ag,N films is very stable and does not revert to n-type, even after 36 months of aging. These results reveal the feasibility of using these films for applications in short-wavelength or transparent optoelectronic devices.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

China's economic development has shifted from high speed to high quality. This study constructs an evaluation index for China’s high-quality development utilizing a new development concept. The entropy method and cluster analysis were used to assess the level of high-quality development in China between 2015 and 2021. Kernel density estimation method was employed to explore spatiotemporal dynamics. The results reveal significant differences in the level of economic development among provinces in China; the eastern region is significantly better than the central, northeastern, and western regions. From the perspective of the sub-item evaluation, challenges with uneven, uncoordinated, and insufficient economic development exist in various Chinese provinces.

Background: Systemic lupus erythematosus (SLE) is characterized by inflammation and cardiovascular complications. Our study aimed to investigate subclinical and early indicators of systolic myocardial dysfunction in SLE patients using advanced echocardiographic methods and biomarkers. Methods: In this cross-sectional study, we enrolled 102 SLE patients without known cardiac impairment and 51 healthy controls. Demographics, disease characteristics, laboratory results, disease activity (SLEDAI) and organ damage (SDI) indices were recorded. Left ventricular global longitudinal strain (GLS) and myocardial work indices were assessed by utilizing speckle tracking echocardiography. In addition, high sensitivity C-reactive protein (hsCRP), high sensitivity troponin (hsTn) and N-terminal-pro B-type natriuretic peptide (NT-proBNP) levels were measured in blood samples. Results: In comparison to controls, SLE patients had significantly higher GLS (-19.94±2.71%vs-21.15±1.55%, p&lt;0.001) and global wasted work (GWW) (94±71mmHg%vs71±49 mmHg%, p=0.025). Notably, NT-proBNP and hsTn were threefold and twofold higher in SLE group compared to control group, respectively (p&lt;0.001). Within SLE cohort, patients with at least moderate disease activity (SLEDAI≥4) both biomarkers were significantly elevated than those with low disease activity (SLEDAI&lt;4). Conclusion: Advanced echocardiographic parameters combined with specific biomarkers have a promising role in detecting systolic dysfunction at an early phase in SLE patients, potentially enabling timely interventions to mitigate cardiovascular risk.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

This paper investigates portfolio optimization methodologies and short-term investment strate-gies in the context of the cryptocurrency market, focusing on ten major cryptocurrencies from January 2020 to November 2023. We employ high frequency data and utilize the Kurtosis Mini-mization methodology, alongside other optimization strategies, to construct and evaluate port-folios under different rebalancing frequencies. The empirical analysis reveals that cryptocurren-cies exhibit significant volatility, skewness, and kurtosis, necessitating sophisticated portfolio management techniques. We find that the Kurtosis Minimization methodology consistently outperforms other optimization strategies, delivering optimal returns to investors, particularly in shorter-term investment horizons. We demonstrate the diversification benefits of integrating cryptocurrencies into multi-asset portfolios and emphasize the importance of regular portfolio rebalancing in the volatile cryptocurrency market. Our findings offer insights for portfolio man-agers and investors seeking to optimize their investment outcomes in the cryptocurrency market, highlighting the importance of risk management, diversification, and dynamic portfolio man-agement strategies.

Shape-shifting polymers usually require not only reversible stimuli-responsive ability, but also strong mechanical properties. A novel shape-shifting photochromic hydrogel system was designed and fabricated through embedding hydrophobic spiropyran (SP) into double polymeric network (DN) by micellar copolymerization. Here, sodium alginate (Alg) and poly acrylate-co-methyl acrylate-co-spiropyran (P(SA-co-MA-co-SPMA)) were employed as the first network and the second network respectively to realize high mechanical strength. After soaked in the CaCl2 solution, the carboxyl groups in the system undergo metal complexation with Ca2+ to enhance the hydrogel. Moreover, after the hydrogel is exposed to UV-light, the closed isomer of spiropyran in the hydrogel network can be converted into an open zwitterionic isomer MC, which is considered to interact with Ca2+ ions. Interestingly, Ca2+ and UV-light responsive programmable shape of the copolymer hydrogel can recover to its original form by immersing in pure water. Since its excellent metal ion and UV-light stimuli-responsive and mechanical properties, the hydrogel has potential applications in the field of soft actuators.

Artistic image completion is fundamental for the preservation and restoration of invaluable art paintings and it has experienced significant progress through the implementation of deep learning methodologies. Despite these advancements, challenges persist, even with sophisticated approaches like Generative Adversarial Networks (GANs), particularly in achieving optimal results for high-resolution paintings. Small-scale texture synthesis and the inference of missing information from distant contexts present persistent issues, leading to distortions in lines and unnatural colors, especially in art paintings with complicated structures and textures. Concurrently, patch-based image synthesis has evolved by incorporating global optimization on the image pyramid to enhance structural coherence and details. However, methods relying on gradient-based synthesis encounter obstacles related to directionality, inconsistency, and the heavy computational burdens associated with solving the Poisson equation in non-integrable gradient fields. This paper introduces a groundbreaking approach, integrating Weighted Similarity-Confidence Laplacian Synthesis, to comprehensively address these challenges and advance the field of artistic image completion. This proposal addresses challenges not only in high-resolution artistic image completion but also makes a significant contribution to the broader field of patch-based synthesis by utilizing the Laplacian pyramid for enhanced edge-aware correspondence search. Experimental result confirms the effectiveness of our approach, offering promising outcomes for the preservation and restoration of art paintings with complicated details and irregular missing regions.

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

The utilization of selective laser melting (SLM) for high entropy alloys (HEAs) holds significant promise in commercial applications, and substantial experimental research efforts have been directed toward this domain. To take advantage of the reported experimental data of SLM manufactured (SLM-ed) HEAs and reduce unnecessary experimentation, this study incorporates machine learning (ML) techniques for the phase and tensile properties prediction of SLM-ed HEAs, thus presenting a novel avenue for accelerating the discovery of new SLM-ed HEAs. Through the adjustment of material descriptors and machine learning models, a model has been developed with an impressive accuracy of 93.8% in distinguishing between face-centered cubic (FCC), body-centered cubic (BCC), and dual-phase (FCC+BCC). Additionally, optimized models have been devised for the prediction of tensile properties, namely ultimate tensile strength (UTS), yield strength (YS), and elongation (δ), achieving noteworthy MAPEs (mean absolute percentage errors) of 10.33%, 8.55%, and 28.48%, respectively. Furthermore, several HEAs were fabricated using SLM, and the experimental outcomes exhibited a favorable alignment with the predicted results. These efforts carry significant implications in advancing the utilization of SLM for HEAs.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Oxidoreductase (OXR) enzymes are in high demand for biocatalytic applications in food industry and cosmetics: glucose oxidase (GOx), cellobiose dehydrogenase (CBDH), bioremediation: horseradish peroxidase (HRP), laccase (LAC), and medicine for biosensors and miniature biofuel cells (GOx, CBDH, LAC, HRP). They can be used in a soluble form and/or within the yeast cell walls expressed as chimeras on the surface of yeast cells (YSD), such as P. pastoris and S. cerevisiae. However, most of the current studies suffer from either low yield for soluble enzyme expression or low enzyme activity when expressed as chimeric proteins using YSD. This is always the case in studies dealing with heterologous expression of oxidoreductase enzymes, since there is requirement not only for multiple OXR genes integrations into the yeast genome (super transformations), and codon optimization, but also very careful design of fermentation media composition, and fermentation conditions during expression due to need for adding transition metals (copper, iron), and metabolic precursors of FAD and heme. Therefore, scientists are still trying to find optimal formula using above mentioned approaches, and most recently also using protein engineering and directed evolution for additional increase in the yield of recombinant enzyme production. In this review article we will cover all the current state of the art technologies and most recent advances in the field that yielded high expression level for some of these enzymes in specially designed expression/fermentation systems. We will also tackle and discuss new possibilities for further increase in fermentation yield by the cutting-edge technologies such are directed evolution, protein and strain engineering, high-throughput screening methods based on in vitro compartmentalization, flow cytometry and microfluidics.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

We present a new penalized method for estimation in sparse logistic regression models with group structure. Group sparsity suggests us to consider the Group Lasso penalty. Being different from penalized log-likelihood estimation, our method can be viewed as a penalized weighted score function method. Under some mild conditions, we provide non-asymptotic oracle inequalities promoting group sparsity of predictors. A modified block coordinate descent algorithm based on a weighted score function is also employed. The net advantage of our algorithm over the existing Group Lasso-type procedures is that the tuning parameter can be pre-specified. The simulations show that this algorithm is considerably faster and more stable than competing methods. Finally, we illustrate our methodology with two real data sets.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Background High Mobility Group Box-1 (HMGB-1) is implicated in the pathogenesis of thrombosis and cancer. In the present study, we aimed to evaluate its potential role as a diagnostic biomarker of portal vein thrombosis (PVT) among patients with hepatocellular carcinoma (HCC). Methods The study population included N=100 prospectively recruited patients with a novel diagnosis of HCC. We compared circulating HMGB-1 levels between 34 healthy controls, HCC patients with PVT (N=22), and HCC patients without PVT (N=78). Results HCC patients without PVT showed significantly higher median HMGB-1 serum levels (8.2 [5.5-13.1] ng/ml) than those observed in the case of HCC with PVT (5.5 [4.4-8.5] ng/ml; p=0.012) and in healthy controls (4.1 [3.1-8.2] ng/ml; p&lt;0.001). Among HCC patients, at univariate analysis, the presence of PVT was associated with higher median age (p=0.036), larger major cancer node diameter (p&lt;0.001), and lower HMGB-1 serum level (p=0.012). At multivariate analysis, the presence of PVT maintained a positive association with major node diameter p=0.001) and an inverse association with serum HMGB-1 levels (p=0.003). Conclusions These findings indicate that serum HMGB-1 bears an inverse association with PVT complicating HCC at the time of diagnosis and suggest that serum HMGB-1 depletion may mark PVT development in cirrhotic patients with HCC.

The semantic segmentation of high-resolution remote sensing images (HR-RSI) is crucial for a wide range of applications, such as precision agriculture, urban planning, natural resource assessment, and ecological monitoring. However, accurately classifying pixels in HR-RSI faces challenges due to densely distributed small objects and scale variations. Existing techniques, including Convolutional Neural Networks (CNNs) and other methods for hierarchical feature extraction and fusion of remote sensing image, often do not achieve the desired accuracy. In this paper, we propose a novel approach called the Hierarchical Rich-scale Fusion Network (HRFNet) to address these challenges. HRFNet utilizes advanced information rating and image partition techniques to extract rich-scale features within image layers. This allows for the adaptive exploration of both local and global contextual information. Moreover, we introduce a structured intra-layer to inter-layer feature aggregation module, which enables the adaptive extraction of fine-grained details and high-level semantic information from multi-layer feature maps in a highly flexible manner. Extensive experimentation has been conducted to validate the effectiveness of our proposed method. Our results demonstrate that HRFNet outperforms existing techniques, achieving state-of-the-art (SOTA) results on benchmark datasets, specifically the ISPRS Potsdam and Vaihingen datasets.

Objectives: To evaluate the relationship between the type of conization, the volume and dimensions of the cone, with the persistence/recurrence of CIN 2-3, presence of affected margins and post-cone HR-HPV positivity. Methods: 227 women treated with LLETZ and histologically confirmed CIN2-3 were evaluated between 1996 and 2006 and followed up until June 2016. Age, type of resection according to IFCPC 2011, volume, cone dimensions, margins were studied. of resection, post-cone high-risk human papillomavirus (HR-HPV) status and viral load. Determinants of HR-HPV positivity were estimated using unconditional logistic regression and time to recurrence was assessed using Kaplan-Meier curves. Results: Persistent/recurrent CIN2-3 was found in 12 cases (5.2%), type 1 conization was performed in 81 patients, with 5 recurrences (6.1%), type 2 in 101 patients, with 6 recurrences (5 .9%) and type 3 resection in 45 women, with 1 recurrence (2.2%). Volume and dimensions were not associated with recurrence. The Log-Rank Test did not show a significant difference between the 3 treatments (p= 0.18). The free margins in type 1 were 37%, in type 2 resection 61% and in type 3 71% (p=0.001). Resection type 1 had 15% HR-HPV post positive cone, type 2 reached 16% and type 3 had 9%, this difference being non-significant (p=0.58). The incidence of recurrence at 36 months in type 1 resection was 0.08%, in type 2 treatment it was 0.04% and in type 3 resection it was 0.0%. Conclusions : Type 3 resection had a higher proportion of free margins and lower post-cone HR-HPV positivity, with a lower incidence of persistence/recurrence.