Papua is one of part in Indonesia which is the geology research of that place isn’t developed and limited. It causes the seismotectonic of Papua hasn’t been known. WinITDB was used to determine the dip angle plate which was on the north part of Papua. The determination of angle was done through seismicity’s cross section analysis in the area. To show that seismicity, earthquake history data that ever occurred in the area is needed. The result on the seismicity’s cross section of plane A–A’, was confluence by two plates with angle 150° against horizontal on the depth up to ±68 km. On the seismicity’s cross section of plane B–B’ had angle 135° against horizontal on the ±82 km depth. On the plane C–C’ seismicity’s cross section, was confluence of two plate which located between -1,77°S until -4,97°S subducted until 171 km depth on 1,38°N - 4,97°S. It proved that subduction characteristic in the northern Papua which was Australia continent plate subducted to north, followed by collision and the Pacific plate subduction on New Guinea. It is also confirmed by focus mechanism analysis which showed the earthquake activities are controlled by the not really deep active fault.

Hyper-spectral imaging provides the possibility of describing specific characteristics of materials in air, land and water depending on reflections of each material in a specific zone of the electromagnetic spectrum. Hyper-spectral sensors capture images in continuous and narrow spectral bands in the visible, near-infrared, and mid-infrared spectral regions. These sensors look at objects using a large part of the electromagnetic spectrum. Some objects have unique characteristics in certain electromagnetic spectrums. These spectral signatures, known as "spectral signatures," help to identify materials in images. But the main problem with these sensors is that the images they get in bad weather conditions and in the presence of dust or rain or snow are of very poor quality. Therefore, we go to SAR images, which are able to form a high-resolution image even in bad weather conditions. The method proposed in this paper is to obtain the final elements of hyper-spectral images using the decomposition method into a multilayer negative matrix. The reason for using this method is that, unlike the high-spectral images that form the image in a number of high-traffic zones, we can create the image in 8 different frequencies, so the most important thing is to get all the hidden information at those frequencies. And also, we compare between the RDA, SENMAV, OMP, ISMA and ADMM algorithms.

This paper proposes Pierre Bourdieu's sociological concepts of social field, capital, and habitus to analyze water management in Colombia. By mapping the social dynamics of water management, this study examines the interactions and power relationships among agents, including government agencies, private companies, academic institutions, non-profits, and local communities. The analysis reveals how various forms of capital, such as economic, cultural, social, and symbolic, influence water management practices, policies, and the distribution of power. Integrating agent-based modeling with hydrological simulations provides a more nuanced understanding of how social dynamics influence water management. This interdisciplinary approach helps develop more adaptive and equitable strategies by capturing the complex interactions between human behavior and environmental factors. The research demonstrates that agent-based modeling, informed by Bourdieu's sociological framework, offers valuable insights for policy development in regions facing socio-economic and environmental challenges. The study highlights the need to localize the analysis of the social field to capture regional customs and specific social dynamics. This localized approach ensures that water management strategies are more relevant, context-sensitive, and sustainable. This paper advocates for the wider adoption of agent-based modeling in water management, proposing a methodology that combines the engineering principles of practical problem-solving and adaptive design with an understanding of the social complexities in water management.

Background: The skin prick test (SPT) is used to diagnose sensitization to antigens. This study proposes a deep learning approach to infer wheal dimensions, aiming to reduce dependence on human interpretation. Methods: A dataset of SPT images (n=5844) was used to infer a convolutional neural network for wheal segmentation (ML model). Three methods for inferring wheal dimensions were evaluated: the ML model; the standard protocol (MA1); and approximation of the area as an ellipse using diameters measured by an allergist (MA2). The results were compared with assisted image segmentation (AIS), the most accurate method. Bland-Altman, distribution analyses, and correlation tests were applied to compare the methods. The study also compared the percentage deviation among these methods in determining the area of wheals with regular geometric shapes (n = 150) and with irregular shapes (n=150). Results: The Bland-Altman analysis showed that the difference between methods was not correlated with the absolute area. The ML model achieved a segmentation accuracy of 85.88% and a strong correlation with the AIS method (ρ=0.88), outperforming all other methods. Additionally, MA1 showed significant error (13.44±13.95%) for pseudopods. Conclusions: The ML protocol can potentially automate the reading of SPT, offering greater accuracy than the standard protocol.

The objective of image super-resolution is to reconstruct a high-resolution (HR) image with the prior knowledge from one or several low-resolution (LR) images. However, in the real world, due to the limited complementary information, the performance of both single-frame and multi-frame super-resolution reconstruction degrades rapidly as the magnification increases. In this paper, we propose a novel two-step image super resolution method concatenating multi-frame super-resolution (MFSR) with single-frame super-resolution (SFSR), to progressively upsample images to the desired resolution. The proposed method consisting of an L0-norm constrained reconstruction scheme and an enhanced residual back-projection network, integrating the flexibility of the variational model-based method and the feature learning capacity of the deep learning-based method. To verify the effectiveness of the proposed algorithm, extensive experiments with both simulated and real world sequences were implemented. The experimental results show that the proposed method yields superior performance in both objective and perceptual quality measurements, compared to the baseline super-resolution algorithms in the cascade model. In addition, the experiment indicates that this cascade model can be robustly applied to different SFSR and MFSR methods.

As waterflooding multi-layer reservoirs get into the high-water-cut stage, inter-layer conflicts become increasingly serious, leading to a worsening development effect over time. Production layers regroup is an effective approach for resolving inter-layer conflicts and improving waterflooding efficiency. At the current stage, there are limitations for most of the methods of production layers regroup. This article proposes a smart method for optimizing the layer regroup plan based on genetic algorithm. Comprehensively considering various factors that affect the regroup of layers, based on the combination principle of "smaller intra-group variance and larger inter-group variance of each influencing factor are expected ", genetic algorithm is used to calculate the fitness value of the initial combination schemes, the advantageous schemes with higher fitness values are selected as the basis of the next generation. Then crossover and mutation operations are performed to those advantageous schemes to generate new schemes. Through continuous selection and evolution, until the global optimal solution with the highest fitness value is found, the optimal combination scheme is determined. Comparative analysis with numerical simulation results demonstrates the reliability of this intelligent method, with an increased oil recovery of 4.34% for the sample reservoir. Unlike selecting a preferable plan from a limited number of predefined combination schemes, this method is an automatic optimization to solve the optimal solution of the problem. It improves both efficiency and accuracy as compared to conventional reservoir engineering methods, numerical simulation methods and most of the mathematical methods, thus could provide effective guidance for EOR strategies of waterflooding reservoirs in high-water-cut stage.

During tensile testing of materials, strain measurement is conducted using either contact or non-contact methods. Contact methods offer high accuracy and precision but are limited by the specimen's thickness and dimensions, whereas non-contact methods minimize damage to thin specimens and allow measurements in various environments, though they require longer prep-aration and calculation times. This paper proposes a circular grid marking pattern and a strain prediction algorithm using artificial intelligence (AI), which simplifies the preparation process and allows strain prediction without additional equipment. The circular grid pattern can be ar-ranged in various configurations from 1×5 to 5×7, and a laser marker, which requires minimal time, was used to engrave the pattern on the specimen to shorten the preparation time. The AI model, trained on image-based data, enables strain calculation regardless of the specimen's gauge length and size, and allows measurement of local strain as well as gauge-length strain. The reliability of this concept was verified by applying it to tensile testing.

An arc glow discharge device was used to prepare a helical carbon fiber skeleton with helical carbon fibers hooked to each other by spraying hydrogen and ethanol mixture onto the iron wire substrate through the discharge area, using anhydrous ethanol as carbon source. The various growth modes of carbon fiber during the formation of carbon fiber skeleton were investigated. A ring appearance that indicates a change in the direction of carbon fiber growth is observed. And double helical carbon fiber was constructed from single helical carbon fiber in two ways. A super-large carbon fiber with a diameter of about 13μm was observed, and it is speculated that this super-large carbon fiber is the backbone of the carbon fiber skeleton. The mechanical properties of carbon fiber skeleton are isotropic.

Leakage is important in groundwater cycle research and water resource management, the key is to construct the spatial distribution of aquitard. Influenced by natural and anthropogenic factors, the density of boreholes restricts the accuracy of aquitard structure. This paper explores the K-Nearest Neighbor (KNN) method to construct multi-layer aquitard structure in the hinterland of Songnen Plain, Northeast China, with limited boreholes, and compare it with Inverse Distance Weight (IDW) and Ordinary Kriging (OK) methods to evaluate the leakage. The KNN needs to first identify the eigenvalue-k of each layer, which is used to enhance the trainset to obtain the testset with a larger amount of sample data enhanced, and to make a prediction to obtain the 3-dimensional structure of aquitard. KNN is more accurate than the IDW and OK. The aquitrad structure obtained by the KNN is different from the IDW and OK, the thickness difference is 3.53%-54.00%, the area difference is 2.28%-23.91%, and the difference in leakage can be up to 24.51%. KNN also has a high degree of identification of aquitard edges, which can help the prevention of groundwater pollution. The results provide guidance for water balance analysis, borehole engineering design, water resources management and exploitation.

This study investigates anomaly detection of IoT device traffic using Convolutional Neural Networks (CNN) and Variational Autoencoders (VAE) to enhance the detection capability of security threats in IoT environments. A series of hardware configurations, software environments, and hyperparameters were utilized to optimize the training and testing processes of the models. The CNN model demonstrates robust classification performance, achieving an accuracy rate of 95.85% on the test dataset, effectively distinguishing between different types of IoT device traffic. Meanwhile, the VAE model exhibits proficient anomaly detection capabilities by effectively capturing abnormal patterns in the data using reconstruction loss and KL divergence. The combined use of CNN and VAE models offers a comprehensive solution to cybersecurity challenges in IoT environments. Future research directions include exploring diverse IoT traffic data, practical deployment for validation, and further optimization of model structures and parameters to improve performance and applicability.

The issue of sufficient nutrition and appropriate distribution in school lunch programs presents a significant challenge that must be addressed. Many schools struggle to provide food that meets all of their students’ nutritional needs. Additionally, inconsistencies in nutritional information and administrative difficulties often hinder the efficient operation of these programs. Developing technology to better manage school lunch programs is critical to addressing these issues. The goal of this project is to create a web application that ensures the fair distribution of nutritional information while also increasing the efficiency of lunch program administration. The methodology used in this research is Agile. Agile approaches are employed throughout the development process, allowing for rapid iteration and responsiveness to user feedback. The end result is a web tool called Nourishify, designed to streamline the management and dissemination of nutritional information. Implementing Nourishify led to substantial improvements in access to nutrition information and operational efficiency, making it an innovative solution for school lunch programs. This project demonstrates that integrating technology can significantly enhance the administration and transparency of nutrition programs, ultimately benefiting students' health and well-being. Moreover, Nourishify’s user-friendly interface and real-time data capabilities ensure that all stakeholders, including parents, administrators, and nutritionists, can easily collaborate and access crucial information.

Objectives- The aim of the study is to describe and validate an optical-coherence-tomography (OCT) based method to easily calculate specific volumes, overcoming the inability of current OCT software to automate a volumetric analysis for specific entities in retinal pathologies. Methods- After manual drawing with caliper of the specific entity on linear OCT scans and consequent automated measurement of its area, the following formula was used for volumetric calculation: Volume [mm³] = ∑area [mm²] x OCT-scan distance [mm]. Two independent observers calculated the retinal volume (RV) in eyes with normal foveal profile (NFP) and compared it with the automated measurements performed by the OCT software; as well as the volume of the foveal cavity (FC) or foveoschisis (FS) in eyes with lamellar macular hole (LMH). The measurements were re-acquired after six weeks. Intra- and inter-observer variability and variability with automated RV calculations were analysed. Results- The study included 62 eyes: 30 NFP and 32 LMH eyes. High degree of agreement was determined for inter-observer and intra-observer variability between the two observers or singular observer with Spectralis for RV in NFP eyes; as well as between the two observers for FC/FS volume in LMH eyes. Conclusions- We describe and validate, showing excellent inter- and intra-observer agreement, an easy, reliable and widely applicable method to calculate volumes which can be applied to any entity requiring a specific study in the context of retinal pathologies.

To address the challenge of recognizing ship states accurately amidst the complexities of marine environments, this study proposes a novel ship state recognition approach leveraging a graph convolutional neural network (GCNN). Initially, the method extracts canonical and efficient ship motion trajectories from AIS data. Subsequently, a state recognition network tailored for ship motion trajectories is devised and implemented employing graph convolution. Notably, the accuracy of this model is enhanced through the introduction of novel weights and optimization of the Adj parameter. Experimental evaluations conducted on a ship state dataset demonstrate significant performance improvements. Specifically, the proposed recognition network achieves a recognition accuracy of 98.3% for regulated ship trajectories, marking an impressive 8.4% enhancement over traditional convolutional neural networks. This advancement holds promise for enhancing ship state recognition accuracy across diverse maritime applications including maritime supervision, navigation safety, and ship management.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

In this study, the temporal variation in soil salinity dynamics was monitored and analyzed using Electromagnetic Induction (EMI) in an agricultural area in Port Said, Egypt, which is at risk of soil salinization. To assess soil salinity, repeated CMD2 soil apparent electrical conductivity (ECa) measurements were taken and inverted to generate electromagnetic conductivity imaging (EMCI), representing soil electrical conductivity (σ) distribution through time-lapse inversion. This process involved converting EMCI data into salinity cross sections using a site-specific calibration equation that correlates σ with the electrical conductivity of saturated soil paste extract (ECe) for the collected soil samples. The study was performed from August 2021 to April 2023, involving six surveys during two agriculture seasons. The results demonstrated the accurate prediction ability of soil salinity with R2 value of 0.81. The soil salinity cross sections generated on different dates observed changes in the soil salinity distribution. These changes can be attributed to shifts in irrigation water salinity resulting from canal lining, winter rainfall events, and variations in groundwater salinity. This approach is effective for evaluating agricultural management strategies in irrigated areas where it is necessary to continuously track soil salinity to avoid soil fertility degradation and a decrease in agricultural production and farmer’s income.

Aeromagnetic compensation plays a vital role in geomagnetic navigation and has received considerable attention throughout last few decades. Classical aeromagnetic compensation methods based on the Tolles–Lawson (T-L) model are mainly aimed at permanent, induced, and eddy-current magnetic interferences of aircraft platform, which ignores other stray magnetic field interference on the platform including the interferences caused by on-board electronic (OBE) systems. In order to cooperate with TL model, magnetometers are usually required to be installed on the extension rod outside the cabin, which is widely applied to geophysical magnetic survey. In order to ensure safety and reduce the cost of platform modification in geomagnetic navigation, it’s necessary to place magnetometers inside the cabin. It also further exacerbates the magnetic interferences and improves the difficulty of magnetic compensation. In this paper, a modified aeromagnetic compensation method is proposed, and the in-cabin OBE interferences are respectively modelled to be proportional to the currents and their temporal variations of different electronic devices. To ensure that modified model adapts to strong OBE interference in the cabin, a cut-off frequency determination method based on curvature calculation and a feature selection method based on correlation calculation are proposed. The cut-off frequency determination method helps to select passband filter which suitable for in-cabin OBE interference. The feature selection method can help to effectively select current and voltage inputs for modified model. In addition, principal component analysis (PCA) is adopted to reduce multicollinearity which is intensified by the extension of OBE interferences in coefficient-estimating. Experiments on public dataset are conducted to illustrate the effectiveness of the proposed method, and the best compensation result achieved 1.71nT of root mean square error (RMSE).

Vehicular traffic in urban areas continues to be a constant challenge today, due to the continuous population growth and the increase of vehicles in circulation. Vehicular congestion, as a recurrent problem, generates a negative impact on urban mobility and citizens’ quality of life. It is hypothesized that a dynamic clustering method of vehicle trajectory data can provide an accurate and up-to-date representation of real-time traffic behavior. To evaluate this hypothesis, data were collected from three different cities: San Francisco, Rome and Guayaquil. A dynamic clustering algorithm was applied to identify traffic congestion patterns and an indicator was applied to identify and evaluate the congestion conditions of the areas. The results show a high precision and recall in congestion classification compared to a method based on static cells.

The differentiation of ESCs into cardiomyocytes in vitro is an excellent and reliable model system for studying normal cardiomyocyte development in mammals, modeling cardiac diseases, and for use in drug screening. Mouse ESC differentiation still provides relevant biological information about cardiac development. However, the current methods for efficiently differentiating ESCs into cardiomyocytes are limiting. Here, we describe a “WNT Switch” method to efficiently commit mouse ESCs into cardiomyocytes using the small molecule WNT signaling modulators CHIR99021 and XAV939 in vitro. This method significantly improves the yield of beating cardiomyocytes, reduces number of treatments, and is less laborious.

Radiation therapy is employed in treating various cancer types. However, depending on the type and stage of cancer, its benefits can be limited, and it may cause serious side effects that detrimentally affect the quality of life (QOL) for the patient. Preventing the side effects of radiation therapy can enhance the response to cancer treatment and improve the patient’s QOL. Independently, vitamin C and hydrogen have demonstrated potential in reducing the side effects of anticancer drugs and radiation therapy. Furthermore, both have been postulated to possess direct anticancer properties. However, the effects of their combined therapy remain underexplored. This study investigates the hypothesis that combining vitamin C and hydrogen efficiently prevents radiation-induced injuries. Survival rates were investigated in cancer cell lines (MDA-MB231 and GL261) and normal cells (HUVEC) treated with hydrogen, vitamin C and irradiation. Apoptosis was assessed using the FLICA test, and EMT gene expression was elucidated via the qPCR technique. In the normal cell line, the introduction of vitamin C and hydrogen to the culture medium boosted survival rates, exhibiting a radioprotective effect upon irradiation. In contrast, cancer cells showed a decreased survival rate with the introduction of vitamin C and hydrogen, which was further diminished with irradiation. Treated cancer cells showed signs of apoptosis. Caspase activity in viable cells was reduced by the combination treatment with vitamin C and hydrogen. Additionally, glioblastoma cells treated with this combination showed reduced EMT gene expression. This study reveals that a combined therapy of hydrogen and vitamin C offers radioprotective effects on normal cells and exerts direct anticancer effects on cancer cells, while also amplifying the anticancer effects of radiation. Importantly, this combined therapy attenuated the radiation-induced EMT signature in the GL261 murine glioma cell line, suggesting potential in diminishing treatment resistance and tumor invasion.

The accuracy of star position simulation is the key factor affecting the accuracy of ground calibration test of spacecraft attitude measurement system. To solve the impact of nonimaging polarized stray light on the simulation accuracy of star position in the optical engine of the system, the generation mechanism of non-imaging polarized stray light has been investigated, and an optimization method for polarization balance of the optical engine is proposed. The mathematical model of the incident light aperture angle and the ideal polarization parameter of the optical engine thin film is established, and the optimization evaluation function of polarization balance of the optical engine is constructed. An optical engine polarization balance film with the corresponding full-band binomial attenuation is <0.001 and the phase delay is <1°. Experimental results show that the simulation accuracy of the weak starlight simulation system is improved by 1.64 times using polarization balanced optical engine.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

Most of the damage to Vleg cars was caused by material fatigue. The objectives of the fatigue analysis on Xenia 2011 car wheels with the Finite Element Method using Solidworks are: 1) Knowing the fatigue analysis process on car wheels, 2) Knowing the results of the fatigue analysis on car wheels. The research method used is the Finite Element Method (FEM) method; the re-search steps include model data retrieval from the Wheel code, 3D model creation process, static simulation process according to SAE J 328 standard, mesh variations, fatigue simulation, and finally, standardization of results fatigue simulation regarding the SAE J 328 standard. The re-sults of the fatigue analysis on the Xenia 2011 car wheels obtained an age of 1000,000 cycles when compared with the minimum average of SAE J 328 of 600,000 cycles, this product design is clas-sified as a high cycle, which means it will experience a prolonged failure, and this design has a maximum alternating stress value of 627.4702 MPa, a strain of 0.007105, a displacement of 7.148 mm and a SOF of 0.087890 with a load factor used of 2.5, so overall this Xenia car can be loaded with a load of 1775 kg, if it is more than that, then Wheels will experience cracking.

Understanding the dynamic interaction between piles and surrounding soil under vehicular impacts is essential for effectively designing and optimizing soil-embedded vehicle barrier systems. The complex behavior of pile-soil systems under impact loading, attributed to the soil’s nonlinear behavior and large deformation experienced by both components, presents significant simulation challenges. Popular computation techniques, such as the Updated Lagrangian Finite Element Method (UL-FEM), encounter difficulties in scenarios marked by large soil deformation, e.g., impacts involving rigid piles. While mesh-free particle and discrete element methods offer another option, their computational demands for field-scale pile-soil impact simulations are considerable. We introduce the erosion method to bridge this gap by integrating UL-FEM with an erosion algorithm designed for simulating large soil deformations during vehicular impacts. Validation against established physical impact tests confirmed the method’s effectiveness for flexible and rigid pile failure mechanisms. Additionally, this method was used to investigate the effects of soil mesh density, soil domain sizes, and boundary conditions on the dynamic impact response of pile-soil systems. Our findings provide guidelines for optimal soil domain size, mesh density, and boundary conditions. This investigation sets the stage for improved, computationally efficient techniques for the pile-soil impact problem, leading to better pile designs for vehicular impacts.

A complete model was developed to simulate the behavior of a circular clamped axisymmetric fluid-coupled Piezoelectric Micromachined Ultrasonic Transducer (PMUT). Combining Finite Difference and Boundary Element Matrix (FD-BEM), this model is based on the discretization of the partial differential equation used to translate the mechanical behavior of a PMUT. In the model, both the axial and the transverse displacements are preserved in the equation of motion and used to properly define the neutral line position. To introduce fluid coupling, a Green’s function dedicated to axisymmetric circular radiating sources is employed. The resolution of the behavioral equations is used to establish the equivalent electroacoustic circuit of a PMUT that preserves the average particular velocity, the mechanical power, and the acoustic power. Particular consideration is given to verifying the validity of certain assumptions that are usually made across various steps of previously reported analytical models. In this framework, the advantages of the membrane discretization performed in the FD-BEM model are highlighted through accurate simulations of the first vibration mode and especially the cutoff frequency that many other models do not predict. This high cutoff frequency corresponds to cases where the spatial average velocity of the plate is null and is of great importance for PMUT design because it defines the upper limit above which the device is considered to be mechanically blocked. These modeling results are compared with electrical and dynamic membrane displacement measurements of AlN-based PMUTs in air and fluid. This complete PMUT model using the FD-BEM approach is shown to be very efficient in terms of computation time and accuracy.

The unsupervised domain-adaptive vehicle reidentification approach aims to transfer knowledge from a labeled source domain to an unlabeled target domain, however there are knowledge differences between the target domain and the source domain. To reduce domain differences, existing unsupervised domain-adaptive rerecognition methods generally require access to the source domain data to assist in re-training the target domain model. But for security reasons, in many cases, data between different domains cannot communicate. To this end, this paper proposes an unsupervised domain-adaptive vehicle re-identification method based on source-free knowledge transfer. First, by constructing a passive domain knowledge migration module, the target domain is consistent with the source domain model output to train a generator to generate the "source-like samples". Then, it can effectively reduce the model knowledge difference and improve the model generalization performance. According to the experiment and testing of VeRi776 and VehicleID, two mainstream public data sets in this field, the rank-k and mAP indexes obtained are both improved, and are suitable for object re-recognition tasks without source data.

Due to the high computational burden and the high nonlinearity of the responses, crashworthiness optimizations are notoriously hard-to-solve challenges. Among various approaches, methods like the Successive Response Surface Method (SRSM) have stood out for their efficiency in enhancing baseline designs within a few iterations. However, these methods have limitations that restrict their application. Their minimum iterative resampling required is often computationally prohibitive. Furthermore, surrogate models are conventionally constructed using Polynomial Response Surface (PRS), a method that is poorly versatile, prone to overfitting, and incapable of quantifying uncertainty. Furthermore, the lack of continuity between successive response surfaces results in suboptimal predictions. This paper introduces the Multi-Fidelity Successive Response Surface (MF-SRS), a Gaussian process-based method, which leverages a nonlinear multi-fidelity approach for more accurate and efficient predictions compared to SRSM. After initial testing on synthetic problems, this method is applied to a real-world crashworthiness task: optimizing a bumper crossmember and crash box system. Results, benchmarked against SRSM and the Gaussian Process Successive Response Surface (GP-SRS) – a single-fidelity Gaussian process-driven extension of SRSM, show that MF-SRS offers distinct advantages. Specifically, it improves upon the specific energy absorbed optimum value achieved by SRSM by 14.1 %, revealing its potential for future applications.

The capability of extracting information and analyze it into a common format is essential for performing predictions, comparing projects through cost benchmarking, and for having a deeper understanding of the project costs. However, the lack of standardization and the manual inclusion of the data makes this process very time-consuming, unreliable, and inefficient. To tackle this problem, a novel approach with a big impact is presented combining the benefits of data mining, statistics, and machine learning to extract and analyze the information related to railway costs infrastructure data. To validate the suggested approach, data from 23 real historical projects from the client network rail was extracted, allowing their costs to be comparable. Finally, some machine learning and data analytics methods were implemented to identify the most relevant factors allowing for costs benchmarking. The presented method proves the benefits of data extraction being able to gather, analyze and benchmark each project in an efficient manner, and deeply understand the relationships and the relevant factors that matter in infrastructure costs.

Most existing data synthesis methods are designed to tackle problems such as dataset imbalance, data anonymization and insufficient sample size. There is a lack of effective synthesis methods for the limited number of datasets which contain a large of features and unknown noise to expand the size of the dataset. We propose a data synthesis method, named Adaptive Subspace Interpolation for Sample Optimization (ASISO). The idea is to divide the original feature space into several subspaces with an equal number of samples, and then perform interpolation for the samples in the adjacent subspaces. This method can adaptively adjust the size of the dataset containing unknown noise, and the expanded data typically contain minimal error with actual. Moreover, it adjusts the structure of the samples, which can significantly reduce the proportion of samples with large errors. In addition, the hyperparameters of this method have an intuitive explanation and usually require little calibration. Experimental results on artificial data and benchmark data sets demonstrate that ASISO is a robust and stable method to optimize samples.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Spectrum distribution is a classical licensed spectrum accessing method in mobile communication networks. The licensed idle spectrum resources are authorized and distributed from spectrum owners to mobile users. However, the exponential growth of user capacity brings excessive load pressure on the traditional centralized network architecture. As lack of sufficient supervision and penalty measures, dishonest behaviors of spectrum owners and spectrum users will lead to the unfair status in the distribution process. As a result, the honest participants’ interest will be harmed. As an important supporting infrastructure of Internet of things technology, 6G cannot completely follow the existing spectrum distribution method. Towards 6G network spectrum distribution, an blockchain based licensed spectrum fair distribution method is proposed. A lightweight consensus mechanism named as proof of trust (PoT) is applied to reduce computational power consumption and consensus time overhead. We deploy the method on the Ethereum test chain, theoretical analysis and experimental results demonstrate the fairness, effectiveness and security of the method.

Purpose: Social responsibility has been accepted as a core value of nursing profession, particularly in the area of health disparity, but it seems to be difficult to understand for what is meant by social responsibility. The purpose of this study was to explore ways to define the concept of social responsibility of nursing in order to understand the meaning of social responsibility in the field of nursing profession. Methods: The concept analysis process by Walker and Avant was used to clarify the meaning of social responsibility of nursing. Results: Defining attributes of social responsibility of nursing included praxis, as approach to strategizing for social and structural change of inequity, care for an oppressed group which is under social suffering caused by the privilege and power, and action for health policy change in social and political unequal contexts. The antecedents of social responsibility of nursing included reflectivities in identifying personal characteristics, taking seriously the perspective of other vulnerable population, recognizing social environmental status quo (‘fair or unfair’), developing competences in ethical and moral reasoning with social issues. Consequences of social responsibility of nursing were achieving social justice, as equal access to basic human health need in societal level, equal access to effective nursing practice delivery system and development of health promotion policy for world health administrative practices (“health for all”) in nursing. Conclusion: This study provides a guidance to direct future studies through the procedure of identifying conceptual attributes in the context of social responsibility of nursing. Future studies are suggested to develop instruments for social responsibility as well as development of educational programs to promote social responsibility competences in nursing students and nurses.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

Wireless sensor networks are usually applied in hostile areas where nodes are easy to be moni-tored and captured by adversary. Key distribution is an essential primitive to provide most of security mechanism. However, the characteristic of limited resources of sensors restricts the direct use of conventional key distribution schemes. In this paper, a complete security key distribution scheme based on asymmetric cryptography technology is proposed in both static and mobile scenarios. Mutual authentication is guaranteed using challenge-response mechanism. The per-formance evaluation and security analysis show that the proposed scheme with low complexity not only provides better security for wireless sensor networks, but also reduces storage overhead and key exposure risks.

To solve the problem that the common long-tailed classification method does not use the semantic features of the original label text of the image, and the difference between the classification accuracy of most classes and minority classes is large, the long-tailed image classification method based on enhanced contrast visual language trains the head class and tail class samples separately, uses text image to pre-train the information, and uses enhanced momentum contrast loss function and RandAugment enhancement to improve the learning of tail class samples. On the ImageNet-LT long-tailed dataset, the enhanced contrastive visual-language based long-tailed image classification method has improved all class accuracy, tail class accuracy, middle class accuracy, and F1 values by 3.4%, 7.6%, 3.5%, and 11.2%, respectively, compared to the BALLAD method. The difference in accuracy between the head class and tail class is reduced by 1.6% compared to the BALLAD method. The results of three comparative experiments indicate that the long-tailed image classification method based on enhanced contrastive visual-language has improved the performance of tail classes and reduced the accuracy difference between majority and minority classes.

Dicarbonyls are electrophiles able to generate the so-called advanced glycation end-products (AGEs). Human exposure occurs via ingestion (e.g., food), inhalation (e.g., electronic cigarettes) and dysregulation of endogenous metabolic pathways (e.g., glycolysis). Biological systems can prevent AGEs formation via enzymatic and nonenzymatic reactions. However, the continuous exposure to dicarbonyls may cause the depletion of endogenous substrates and the beginning of AGEs accumulation (i.e., carbonylation). Since this process has been associated with multiple disorders, several studies advocated the use of dicarbonyl binders as food preservatives or as drugs aimed at mitigating carbonylation damages. As reported for other toxicants (e.g., HNE, acrolein), the screening of selective and potent binders can be performed by measuring the residual amount of a selected dicarbonyl substrate, upon its incubation with candidate binders. Unfortunately, naturally occurring dicarbonyls are poorly responsive to many detectors (e.g., UV or MS). For this reason, most of the screening methods that have been reported to date relies on indirect quantification upon derivatization. However, this strategy can potentially lead to inaccurate results since the tested compounds can affect the derivatization yield. Therefore, we herein reported the use of benzylglyoxal (BGO) as a convenient, UV responsive, dicarboyl surrogate. By using BGO as a substrate, we setup an easy and cheap chromatographic assay for the direct measurement of the binding activity towards dicarbonyls, without derivatization. The method was qualified by assessing the binding ability of some known dicarbonyl binders, obtaining results consistent with literature.

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

This study aims to optimize the subway platform passenger flow guidance method using Anylogic simulation software. The objective of the study is to minimize overcrowding within subway carriages, enhance transportation capacity, and augment service levels by guiding passengers on the platform to board trains in a distributed manner. The study achieves a balanced flow of passengers in each carriage by taking into consideration the number of passengers in each carriage, the number of passengers at the station, and the expected number of passengers disembarking from the trains. The standard deviation of balance is used to optimize the subway platform passenger flow guidance method. We simulated Guangzhou Metro Zhujiang New Town Line 5 platform to compare different guidance methods and evaluate their effects on the uneven distribution of passengers with passenger flows ranging from 120K to 600K people per day. Our results show that guidance method 2, relative to manual guidance, improves by 38.5% under a daily passenger flow of 240K people on Zhujiang New Town Line 5. Guidance method 3 improves by 25.7% relative to guidance method 2 and by 54.4% relative to manual guidance.

We consider a class of density-driven flow problems. We are particularly interested in the problem of the salinization of coastal aquifers. We consider the Henry saltwater intrusion problem with uncertain porosity, permeability, and recharge parameters as a test case. The reason for the presence of uncertainties is the lack of knowledge, inaccurate measurements, and inability to measure parameters at each spatial or time location. This problem is nonlinear and time-dependent. The solution is the salt mass fraction, which is uncertain and changes in time. Uncertainties in porosity, permeability, recharge, and mass fraction are modeled using random fields. This work investigates the applicability of the well-known multilevel Monte Carlo (MLMC) method for such problems. The MLMC method can reduce the total computational and storage costs. Moreover, the MLMC method runs multiple scenarios on different spatial and time meshes and then estimates the mean value of the mass fraction. The parallelization is performed in both the physical space and stochastic space. To solve every deterministic scenario, we run the parallel multigrid solver ug4 in a black-box fashion. We use the solution obtained from the quasi-Monte Carlo method as a reference solution.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

There is a considerable amount of research in online social networks, most of which focuses on the structural analysis of social graphs. The interpersonal relationships of social networks, especially friend circle, can solve the cold start and sparsity problems, and through the relationship between social networks can effectively recommend users' favorite items (items), such as music , videos, brands/products, preferred tags, location, services, etc. User relationships in social networks are diverse and there are many different perspectives on different social networks. Associations among users can form multi-layered composite networks, and multi-layered social networks present new challenges and opportunities. Different relationships can influence users' preferences to different degrees, which in turn affects their behavior. Therefore, fusing multiple social networks is an effective way to improve recommendation. Although some studies have started to address multiple social network recommendations, simple linear superposition cannot reflect the coupling and nonlinear association between multiple social networks. In this paper, we propose a graph neural network recommendation model under social relationships based on this background. We first propose to compute the 2nd order collaborative signals and their intensities directly from the neighboring matrix for updating the node embedding of the graph convolution layer. Secondly by embedding historical evaluations, various social networks constituting different dimensions, the attention integration of user preferences by different social networks is achieved, and its effectiveness and scalability are demonstrated in theoretical derivation and experimental validation. The theoretical derivation and experimental validation demonstrate its effectiveness and scalability.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

Since financial institutions faced to fatal scenario like subprime mortgage crisis and COVID-19, the factor-based asset allocation methodology is noticed. Asset-only approach which make to consider restrictive risk volatility as individual assets had limitation of macro factor risk. For instance, an institution which allocated assets by asset-only approach cannot deal with the inflation crisis. We review the problem of the traditional modern portfolio approach that is used by Korean financial institutions. For reasonable investment of institution, we notice improved factor-based allocation approach. The first result of this paper is that Mean-variance approach as considered only return of asset recorded lower performance than multi factor-based portfolio in macro factor crisis. Second, we notice allocation model which can minimize probability passing the liability risk exposed macro factors to investment risk exposed macro factors. There are three steps in multi-macro factor-based asset allocation approach: discovering macro factors and mapping asset classes to individual macro factor. Second, define liability account and mapping as considering income and pay out of institution. Third, minimize correlation of fac-tor-based asset risk with liability volatility. Furthermore, using covariance return of assets to allocate makes Pareto improvement and supports to break Home-bias problems.

The sonification of data to communicate information to a user is a relatively new approach that established itself around the 1990s. To date many researchers design their individual sonification from scratch. There are no standards in sonification design and evaluation. But researchers and practitioners have formulated several requirements and established several methods. There is wide consensus that psychoaocustics could play an important role in the sonification design and evaluation phase. But this requires an adaption of psychoacoustic methods to the signal types and the requirements of sonification. In this method paper we present PAMPAS, a PsychoAcoustical Method for the Perceptual Analysis of multidimensional Sonification. A well-defined and well-established, efficient, reliable and replicable Just Noticeable Difference experiment using the Maximum Likelihood Procedure serves as the basis to achieve linearity of parameter mapping during the sonification design stage and to identify and quantify perceptual effects during the sonification evaluation stage, namely the perceptual resolution, hysteresis effects and perceptual interferences. The experiment results are universal scores from a standardized data space and a standardized procedure. These scores can serve to compare multiple sonification designs of a single researcher, or even between different research groups. The method can supplement other sonification design and evaluation methods from a perceptual viewpoint.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

Toxicologically relevant levels of the psychoactive ∆9-tetrahydocannabinol (∆9-THC) as well as high levels of non-psychoactive cannabinoids potentially occur in CBD (cannabidiol) oils. For consumer protection in the fast-growing CBD oil market, facile and rapid quantitative methods to determine the cannabinoid content are crucial. However, the current standard method, i.e., liquid chromatography combined with tandem mass spectrometry (HPLC-MS/MS), requires a time-consuming multistep sample preparation. In this study, a quantitative nuclear magnetic resonance spectroscopy (qNMR) method for screening cannabinoids in CBD oils was developed. Contrary to the HPLC-MS/MS method, this qNMR features a facile sample preparation, i.e., only diluting the CBD oil in deuterochloroform. Pulse length-based concentration determination (PULCON) enables a direct quantification using an external standard. The signal intensities of the cannabinoids were enhanced during the NMR spectra acquisition by means of multiple suppression of the triglycerides which are a major component of the CBD oil matrix. The validation confirmed linearity for CBD, cannabinol (CBN), ∆9-THC and ∆8-THC in hemp seed oil with sufficient recoveries and precision for screening. Comparing the qNMR results to HPLC-MS/MS data for 46 commercial CBD oils verified the qNMR accuracy for ∆9-THC and CBD but with higher limits of detection. The developed qNMR method paves the way for increasing the sample throughput as a complementary screening before HPLC-MS/MS.

Multi-criteria decision-making (MCDM) methods and techniques have been applied to many real-world problems in different fields of engineering science and technology. The evaluation based on distance from average solution (EDAS) method is a new and efficient MCDM method. The aim of this study is to propose a modification to address two exceptional cases in which the EDAS method fails to solve an MCDM problem.

Wi-Fi based localization has become one of the most practical methods for mobile users in location-based services. However, due to the interference of multipath and high-dimensional sparseness of fingerprint data, the localization system based on received signal strength (RSS) is hard to obtain high accuracy. In this paper, we propose a novel indoor positioning method, named JLGBMLoc (Joint denoising auto-encoder with LightGBM Localization). Firstly, because the noise and outliers may influence the dimensionality reduction on high-dimensional sparseness fingerprint data, we propose a novel feature extraction algorithm, named joint denoising auto-encoder (JDAE), which reconstructs the sparseness fingerprint data for a better feature representation and restores the fingerprint data. Then, the LightGBM is introduced to the Wi-Fi localization by scattering the processed fingerprint data to histogram, and dividing the decision tree under leaf-wise algorithm with depth limitation. At last, we evaluated the proposed JLGBMLoc on UJIIndoorLoc dataset and Tampere dataset, experimental results show that the proposed model increases the positioning accuracy dramatically comparing with other existing methods.

This paper has experimentally measured volcanic tufa electrical conductance. The calculations are carried out in accordance with the potential of cyclic voltammetry in a constant state. The cyclic voltammograms nanoelectrode platinum prepared electrochemically were examined in the range -0.2 to 1.2 V vs. AgCl [Cl^-]:1.0 M in the presence and absence of volcanic tuff in the aqueous solution of 1.0 M HCl. The cyclic voltammetry studies show that the Nano platinum film suffers degradation when the potential exceeds +0.85 V, and below this potential, it is quite stable. The redox reaction of the electrode is reversible. The nanoparticle platinum synthesized at low temperature and high acid concentration exhibits higher electronic conductivities. It has been observed that, relative to area under the peak aggregate tests, the use of volcanic concrete was showing a large increase in electrical conductivity. It was shown that with cyclic voltammetry, three well-defined anode peak could be achieved at a power of 0.0, 0.4 and 0.6 V versus Ag/AgCl.

One of the biggest challenges in characterizing 2-D image topographies is finding a low-dimensional parameter set that can succinctly describe, not so much image patterns themselves, but the nature of these patterns. The 2-D Cluster Variation Method (CVM), introduced by Kikuchi in 1951, can characterize very local image pattern distributions using configuration variables, identifying nearest-neighbor, next-nearest-neighbor, and triplet configurations. Using the 2-D CVM, we can characterize 2-D topographies using just two parameters; the activation enthalpy and the interaction enthalpy. Initial investigations with two different representative topographies (``scale-free-like'' and ``rich club-like'') produce interesting results when brought to a CVM free energy minimum. Additional phase space investigations, where one of these two parameters has been set to zero, identify useful parameter ranges. Careful comparison of the analytically-predicted configuration variables versus those obtained when performing computational free energy minimization on a 2-D grid show that the computational results differ significantly from the analytic solution. The 2-D CVM can potentially function as a secondary free energy minimization within the hidden layer of a neural network, providing a basis for extending node activations over time and allowing temporal correlation of patterns.

Product Design is getting nowadays new challenges on developing new products, since the industry is in a rush to introduce products into the marketplace, where customers demand products faster, cheaper, and free of failures. In the meantime, global companies are always trying to improve their Product Design process to get advantages over their competitors using proven tools like FEMA and mixing methodologies like Fuzzy theories with FMEA. Even today using all this tools and combination of methodologies there is a gap to address and it is required a robust risk analysis solving current issues in the electronic industry. This document aims to reveal a novel integrated method, where Failure Mode and Effect Analysis, Pythagorean Fuzzy Sets and Dimensional Analysis are cohesive into a model that minimize the uncertainty of the ranking and prioritization over the Failure Mode and Effect Analysis execution, helping to identify risks within an accurate grade over possible failures in the Product Design process. A real practical example is used to show the proposed method, where it is identified a robust methodology integration and solid and results using a sensitivity analysis.

This paper discusses approaches to the numerical integration of the coupled nonlinear Schrödinger equations system in case of few-mode wave propagation. The wave propagation assumes the propagation of up to nine modes of light in an optical fiber. In this case, the light propagation is described by the non-linear coupled Schrödinger equation system, where propagation of each mode is described by own Schrödinger equation with other modes interactions. In this case, the non-linear coupled Schrödinger equation system solving becomes increasingly complex, because each mode affects the propagation of other modes. The suggested solution is based on the direct numerical integration approach, which is based on a finite-difference integration scheme. The well-known explicit finite-difference integration scheme approach fails, due to the non-stability of the computing scheme. Due to this fact, the combined explicit/implicit finite-difference integration scheme, based on the implicit Crank–Nicolson finite-difference scheme, is used. It allows ensuring the stability of the computing scheme. Moreover, this approach allows separating the whole equation system on the independent equation system for each wave mode at each integration step. Additionally, the algorithm of numerical solution refining at each step and the integration method with automatic integration step selection are used. The suggested approach has performance gains (or resolutions) up to three or more orders of magnitude in comparison with the split-step Fourier method due to the fact that there is no need to produce direct and inverse Fourier transforms at each integration step. The main advantage of the proposed method is the ability to calculate the propagation of an arbitrary number of modes in the fiber.

We present a cost- and time-efficient method for the controlled preparation of single phase La(IO3)3 nanoparticles via a simple soft-chemical route which takes a matter of hours, thereby providing an alternative to the common hydrothermal method which takes days. Nanoparticles of pure α-La(IO3)3 and pure δ-La(IO3)3 were synthesised via the new method depending on the source of iodate ions, thereby demonstrating the versatility of the synthesis route. The crystal structure, nanoparticle size-dispersal and chemical composition were characterised via angle- and energy-dispersive powder X-ray diffraction, scanning electron microscopy and Fourier-transform infrared spectroscopy.

Increased chronic glucose is associated with pandemic diseases. To date, there is not a practical, as well as accurate sample for reflecting that level. We measured earwax glucose in 37 controls. They provided standard serum samples, Glycated Haemoglobin (HbA1c) and earwax samples on two time-points, one month a part. The specimens measured baseline fasting glucose, a follow-up postprandial glucose level and a between sample chronic glucose, calculated using the average level on the two occasions. The baseline earwax sample was obtained using a clinical method and the follow-up using a novel self-sampling earwax device. The earwax analytic time was significantly faster using the novel device in comparison to the clinical use of the syringe. Earwax accurately reflected glucose at both assessments with stronger correlations than HbA1c. Follow-up postprandial concentrations were more significant than their respective fasting baseline concentrations, reflecting differences in fasting and postprandial glycaemia and more efficient standardisation at follow up. Earwax demonstrated to be more predictable than HbA1c in reflecting systemic fasting, postprandial and long-term glucose levels and immune by confounders. Earwax glucose was approximately 60% more predictable than HbA1c in reflecting glycaemia over a month. The self-sampling device provided a sample that might accurately reflect chronic glycaemia.

The zero velocity update(ZUPT) algorithm is the core of a foot-mounted pedestrian navigation system. The zero velocity detection method is the premise and guarantee of the effective application of the ZUPT algorithm. To make ZUPT work properly, it is necessary to detect zero velocity intervals correctly. The detection accuracy of the existing zero velocity detection methods is easy to be affected by users and environment. A novel zero velocity detection method based on the plantar pressure is proposed in this paper, which has higher detection accuracy and better environmental adaptability. First, the paper analyzes the motion characteristics of foot during walking. Second, the inherent relationship between the plantar pressure and the gait change during walking is studied based on the pressure sensor. Then, the model of the zero velocity detection method using the plantar pressure is established. Finally, the indoor and outdoor multi-scene experiments show that this method not only has a high detection accuracy, but also has good adaptability to users and walking environment.

In many developed countries, mental health disorders have become problematic, and the economic loss due to treatment costs and interference with work is immeasurable. Therefore, we developed a method to assess individuals’ mental health using emotional components contained in their voice. We propose two indices of mental health: vitality, a short-term index, and mental activity, a long-term index capturing the trends in vitality. To evaluate our method, we used the voices of healthy individuals (n = 14) and patients with major depression (n = 30). The patients were also assessed by specialists using the Hamilton Rating Scale for Depression (HAM-D). A significant negative correlation existed between the vitality extracted from the voices and HAM-D scores (r = -0.33, p &lt; .05). We could discriminate the voice data of healthy individuals and patients having depression with a high accuracy using the vitality (p = .0085, area under the curve = 0.76). Further, we developed a method to estimate stress through emotion instead of analyzing stress directly from voice data. By daily monitoring of vitality using smartphones, we can encourage hospital visits for people before they become depressed or during the early stages of depression, to prevent adverse consequences of depression.

In the present work, a novel conductive liquids method of study has been proposed. It is based on the phenomenon of radiofrequency anisotropy of electrolyte solution discovered by us. It arises in response to mechanical or acoustic excitation of the solution. We have observed the phenomenon during the development of an RF polarimetric contactless cardiograph. The electric field vector of the transmitted 433.82 MHz signal rotated after its transition through the pericardial region. That rotation depends on the change of blood acceleration when passing through the chambers of the heart and large vessels. It has also been revealed that rotation occurs after RF wave passage through the physiological saline (0.9% NaCl) subjected to any mechanical excitation inside it like a jet appearing or soundwave passing. No significant difference was detected experimentally between NaCl and KCl solutions behavior. It means that the mechanism of hydrodynamic separation of ions is apparently not suitable to explain the phenomenon. The response we have registered resembles the magnetization process of spin glasses. From the nature of the observed response, we have concluded that a fundamentally new physical effect is discovered. It may provide wide opportunities for remote measurement of the electrolyte solution parameters with polarized radio-frequency signals.

Transcriptionally controlled tumor protein (TCTP) is a highly conserved protein performing a large number of cellular functions by binding with various partner proteins. The importance of its roles in many diseases requires an assay method to find regulatory compounds. However, the molecular characteristics of TCTP made it difficult to search for chemicals interacting with it. In this study, a tryptophan-based assay method was designed and Y151W mutant TCTP was constructed to search binding chemicals. Since there is no tryptophan in the native sequence of TCTP, the incorporation of tryptophan in the Y151W mutant was very effective to establish the method. A flavonoid library was employed to the assay with the method. With the native and Y151W mutant TCTPs, three flavonoids such as morin, myricetin and isobavachalcone have been found to interact with TCTP. Combined with native gel electrophoresis, the binding region of isobavachalcone was suggested to be the flexible loop of TCTP. This approach can be easily applicable to find binding compounds of proteins with similar molecular characteristics of TCTP.

In the recent years, intelligent data-driven faultdiagnosis methods on gearboxes have been successfully developedand popularly applied in the industries. Currently, most ofthe machine learning techniques require that the training andtesting data are from the same distribution. However, thisassumption is difficult to be met in the real industries, sincethe gearbox operating conditions usually change in practice,which results in significant data distribution gap and diagnosticperformance deteriorations in applying the learned knowledgeon the new conditions. This paper proposes a deep learning-based domain adaptation method to address this issue. Theraw current signals are directly used as the model inputs fordiagnostics, which are easy to collect in the real industries andfacilitate practical applications. The maximum mean discrepancymetric is introduced to the deep neural network, the optimizationof which guarantees the extraction of generalized machineryhealth condition features across different operating conditions.The experiments on a real-world gearbox condition monitoringdataset validate the effectiveness of the proposed method, whichoffers a promising tool for cross-domain diagnosis in the realindustries.

A fast calculation method for the full parallax high-resolution hologram is proposed based on the elemental light field image (EI) rendering. A 3D object located near the holographic plane is firstly rendered as multiple EIs with a pinhole array. Each EI is interpolated and multiplied by a divergent sphere wave and interfered with a reference wave to form a hogel. Parallel acceleration is used to calculate the high-resolution hologram because calculation of each hogel is independent. A high-resolution hologram with the resolution of 20,0000×20,0000 pixels is calculated only within 8 minutes. Full parallax high-resolution 3D displays are realized by optical reconstructions.

Although the Slicing Method (SM) is effective for calculating the volume of point cloud objects (PCOs), it is restricted in terms of applicability and practicability because of a certain contingency and directional defects. The Co-Opposite-Direction Slicing Method (CODSM) proposed in this paper is an improved method for calculating PCO volume by increasing parallel (co-opposite-direction) observation and considering the two-way mean as the result. This method takes full advantage of the mutual offsetting of random errors and the compensation of systematic directional errors, which can effectively overcome (or mitigate) the effect of random errors and reduce the effect of systematic errors in SM. In this paper, two typical objects, a cone model and a stone lion base, are the examples for calculating PCO volume using CODSM. The results show that CODSM has all the inherent advantages of SM and effectively weakens the volatility of random errors and the directionality of systematic errors from SM. Therefore, CODSM is a robust configuration upgrade of SM.

In the case that ship operators may not be aware of the potential risks of environmental factors in situation of high causation probability during the initial stage of the geometric probability analysis process, it is likely that higher-grade collision accident measures will not be taken. However, if any risks is told to the ship operators, more effective and intentional measures can be taken in time. Moreover, if the causation probability corresponding to environmental factors is no less than the risk early warning critical value calculated based on historical collision accident data, there would be a high-risk level that a collision may occur. A new method is put forward based on quantitative analysis of environmental factors and previous collision statistics to provide early warning of any accident risk, and a risk early-warning critical value (REWCV) can be obtained based on this simple but highly operational and practical method. A case study of Three Gorges Reservoir in China indicates that the range of environmental factors where the probability of collision accident grows rapidly is consistent with environmental limits defined by Chinese maritime standards. In addition, the relationship between the risk early-warning critical value and the number of previous collision accident is also clarified.

As a novel concept in technology and communication world, “Internet of Things (IoT)” has been emerged. In such modern technology, the capability to transmit data through data communication networks (such as Internet or Intranet) is provided for each organism (e.g. human being, animals, things, and so forth). Due to the limited hardware and communication operational capability as well as small dimensions, IoT undergoes quite a few challenges. Such inherent challenges not only cause fundamental restrictions in the efficiency of aggregation, transmission, and communication between nodes; but they also degrade routing performance. To cope with the reduced availability time and unstable communications among nodes, data aggregation and transmission approaches in such networks are designed more intelligently. In this paper, a distributed method is proposed to set child balance among nodes. In this method, the height of the network graph is increased through restricting the degree; and network congestion is reduced as a result. Besides, a dynamic data aggregation approach -named as LA-RPL- is proposed for RPL networks. More specifically, each node is equipped with learning automata in order to perform data aggregation and transmissions. Simulation results demonstrate that the proposed approach outperforms previously suggested based approaches in terms of energy consumption, network control overhead, and packet loss rate.

In this paper, we introduce some basic idea of Variational iteration method for short (VIM) to solve the Volterra’s integro-differential equations. The VIM is used to solve effectively, easily, and accurately a large class of non-linear problems with approximations which converge rapidly to accurate solutions. For linear problems, it’s exact solution can be obtained by only one iteration step due to the fact that the Lagrange multiplier can be exactly identified. It is to be noted that the Lagrange multiplier reduces the iteration on integral operator and also minimizes the computational time. The method requires no transformation or linearization of any forms. Two numerical examples are presented to show the effectiveness and efficiency of the method. Also, we compare the result with the result from Homotopy perturbation method (HPM). Finally, we investigate the absolute difference between variational iteration method and homotopy perturbation method and draw the graph of difference function by using Mathematica.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.

Infiltration based stormwater best management practices bring considerable economic, social and ecological benefits. Controlling stormwater quantity and quality are primarily important to prevent urban flooding and minimizing loads of pollutants to the receiving waters. However, there have been growing concerns about how the traditional design approach contributes to the failure of infiltration based BMP’s that have caused flooding, ponding, prolonged movement of surface water, and frequent clogging, etc. Many of these problems were due to the fact that the current design approaches of stormwater BMP’s only focus on surface hydrology and give little or no attention to the underline subsoil permeability rate and other constraints during the design and sizing process. As a result, we are exhibiting many newly constructed infiltration based BMP’s are failing to function well. This paper presents and demonstrates a new paradigm shift in designing infiltration-based stormwater BMP’s by combining subsurface hydrology and undelaying native soil constraints to establish acceptable criteria for sizing infiltration based BMPs.

The creation of hydrophobic, antifreeze and self-cleaning coatings is currently being pursued by many industrial sectors. The potential applications include the production of liquid and gas separators and filters, new materials, optical and microelectronic devices, and textiles and clothing. These coatings will also have wide application in the construction and automobile industries, shipping, and energy and agricultural sectors. The article proposes a simple approach to the creation of superhydrophobic and antifreeze coatings, by applying powder from multi-walled carbon nanotubes (MW-CNTs) to the sample surface. This method enables combination of the necessary factors: low surface energy, micro–nano-roughness and hierarchical multi-scale. The authors investigated the dependence of the wetting angle of such a surface on the time, type and degree of functionalization. The electrophysical properties of modified MW-CNTs were studied over wide frequency and temperature ranges. This method of obtaining hydrophobic coatings differs from currently available methods in that it is simpler to prepare, is of lower cost and has less environmental impact. The proposed approach can be used to create superhydrophobic coatings that have the additional function of removing static charge and therefore reducing surface heating, and which can be used in the field of energetics for protection against the freezing of wind turbine blades and aircraft surfaces.

DGJ (Daftardar-Gejii-Jafaris) method is used to obtain numerical solution of the third order fractional differential equation. Providing the DGJ method converges, the approximate solution is a good and effective numerical result which is close to the exact solution or the exact solution. For this,the examples of the explaning the method are presented. The proposed method is implemented for the approximation solution of the third order nonlinear fractional partial differential equations. The method was shown to be unsuitable and inconsistent for an example of a nonlinear fractional partial differential equation depend on initial-boundary value conditions. The fact that these numerical results are not consistent can be explained by the fact that the method is not convergent.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

Crowd counting is of significant importance for numerous applications, e.g., urban security, intelligent surveillance and crowd management. Existing crowd counting methods typically require specialized hardware deployment and strict operating conditions, thereby hindering their widespread deployment. To acquire a more effective crowd counting approach, a device-free counting method based on Channel Status Information (CSI) is proposed, which could mitigate environment noise through wavelet transform and extract the amplitude or phase covariance matrix as the feature vector. Moreover, both the spatial diversity and frequency diversity are leveraged to improve detection robustness. The accuracy of the proposed CSI-based method is compared with a renowned crowd counting one, i.e., Electronic Frog Eye: Counting Crowd Using WiFi (FCC). The experimental results reveal an accuracy improvement of 30% over FCC.

Counterfeiting electronic components is a serious problem for the security and reliability of any electronic systems. Unfortunately, the number of counterfeit components has increased considerably after the introduction of horizontal semiconductor supply chain. In this paper, we propose a new method for detecting recycled Flash memory, a major target of the counterfeiters due to its ubiquitous usage. Proposed method is based on measurement of change in Flash array characteristics (such as erase time, program time, fail bit count, etc.) with its usage. We find that erase time is the best metric to distinguish a used Flash chip from a fresh one for the following reasons: (1) erase time shows minimal variation among different fresh memory blocks/chip and (2) erase time increases significantly with usage. We verify our method for a wide range of commercial off the shelf Flash chips from several vendors, technology nodes, storage density and storage type (single-bit per cell and multi-bit per cell). The minimum detectable chip usage varies from 0.05% to 3.0% of its total lifetime depending on the exact details of the chip.

We propose a new Mamdani fuzzy rule-based system in which the fuzzy sets in the antecedents and consequents are assigned in a discrete set of points and approximated by using the extended inverse fuzzy transforms, whose components are calculated by verifying that the dataset is sufficiently dense with respect to the uniform fuzzy partition. We test our system in the problem of spatial analysis consisting in the evaluation of the liveability of residential housings in all the municipalities of the district of Naples (Italy). Comparisons are done with the results obtained by using trapezoidal fuzzy numbers in the fuzzy rules.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

Sensitivity to weather conditions, and specially to clouds, is a severe limiting factor to the use of optical remote sensing for Earth monitoring applications. A possible alternative, is to resort to weather-insensitive synthetic aperture radar (SAR) images. However, in many real-world applications, critical decisions are made based on some informative spectral features, such as water, vegetation or soil indices, which cannot be extracted from SAR images. In the absence of optical sources, these data must be estimated. The current practice is to perform linear interpolation between data available at temporally close time instants. In this work, we propose to estimate missing spectral features through data fusion and deep-learning. Several sources of information are taken into account - optical sequences, SAR sequences, DEM - so as to exploit both temporal and cross-sensor dependencies. Based on these data, and a tiny cloud-free fraction of the target image, a compact convolutional neural network (CNN) is trained to perform the desired estimation. To validate the proposed approach, we focus on the estimation of the normalized difference vegetation index (NDVI), using coupled Sentinel-1 and Sentinel-2 time-series acquired over an agricultural region of Burkina Faso from May to November 2016. Several fusion schemes are considered, causal and non-causal, single-sensor or joint-sensor, corresponding to different operating conditions. Experimental results are very promising, showing a significant gain over baselines methods according to all performance indicators.

Many of engineering’s problems are about to optimise equations, functions and process models equations which appear on common or even complex science’s cases. Most applied optimisation methods nowadays can only be used on particular cases, so the main objective of this article is to define a computational method that can optimise or even find target values for specified objective functions and variables, by just using computer effort. Chemical plants involve many differential equations and they can be optimised with more facility now. On this paper, there are shown as example, an optimisation for a chemical reactor, which is found the optimal temperature and volumetric flow rate of feed, for the given objective function being the composition of the desired product. Named Domain’s Sweep, it is an algorithm that evaluate given(s) mathematical function(s) and/or equation(s) by varying your(s) independent variable(s) through loops with a given step size and solving it after closing the degrees of freedom, and finally, with some condition statements, store all the optimum values of given or created objective functions with its respective independent variables. In another words, the user create an objective function and this method find the function’s maximum, minimum or a certain chosen target value, even if it does not have an inflection point in the given search interval of the independent variables.

This paper shows a method for pipeline leak detection using a transient-based method with MATLAB® functions. The simulation of a pipeline systems in the time domain are very complex. In the case of the dissipative model, transfer functions are hyperbolic Bessel functions. Simulating a pipeline system in the frequency domain using a dissipative model we could find an approximate transfer function with equal frequency domain response to in order get the pipeline system's time domain response. The method described in this paper can be used to detect, by comparison, to detect a leak in a pipeline system model.

To solve large scale linear equations involved in the Fast Multipole Boundary Element Method (FM-BEM) efficiently, an iterative method named the generalized minimal residual method (GMRES)(m)algorithm with Variable Restart Parameter (VRP-GMRES(m) algorithm) is proposed. By properly changing a variable restart parameter for the GMRES(m) algorithm, the iteration stagnation problem resulting from improper selection of the parameter is resolved efficiently. Based on the framework of the VRP-GMRES(m) algorithm and the relevant properties of generalized inverse matrix, the projection of the error vector r_m+1 on r_m is deduced. The result proves that the proposed algorithm is not only rapidly convergent but also highly accurate. Numerical experiments further show that the new algorithm can significantly improve the computational efficiency and accuracy. Its superiorities will be much more remarkable when it is used to solve larger scale problems. Therefore, it has extensive prospects in the FM-BEM field and other scientific and engineering computing.

This paper formulates the performance evaluation of cloud services as a multicriteria group decision making problem, and presents a fuzzy multicriteria group decision making method for evaluating the performance of cloud services. Interval-valued intuitionistic fuzzy numbers are used to model the inherent subjectiveness and imprecision of the performance evaluation process. An effective algorithm is developed based on the technique for order preference by similarity to ideal solution method and the Choquet integral operator for adequately solving the performance evaluation problem. An example is presented to demonstrate the applicability of the proposed fuzzy multicriteria group decision making method for solving the multicriteria group decision making problem in real world situations.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Background: Approximately 75% of all head and neck cancer patients are treated with radiotherapy (RT). RT to the oral cavity results in acute and late adverse events which can be severe and detrimental to a patient’s quality of life and function. The purpose of this study was to explore associations between RT dose to a defined oral cavity organ at risk (OAR) avoidance structure, provider and patient reported outcomes (PROs), opioid use, and hospitalization. Methods: This was a retrospective analysis of prospectively obtained outcomes using multivariable modeling. The study included 196 patients treated with RT involving the oral cavity for a head and neck tumor. A defined oral cavity OAR avoidance structure was used in all patients for RT treatment planning. Validated PROs were collected prospectively. Opioid use and hospitalization were abstracted electronically from medical records. Results: Multivariable modeling revealed the mean dose to the oral cavity OAR was significantly associated with opioid use (p=0.0082) and hospitalization (p=0.0356) during and within 30 days of completing RT. Conclusion: The findings of this study may be valuable in RT treatment planning for patients with tumors of the head and neck region to reduce the need for opioid use and hospitalization during treatment.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Multicore magnetic nanoparticles of manganese ferrite were prepared using carboxymethyl-dextran and melamine as agglutinating agents. The nanoparticles prepared using melamine exhibit a flower-shape structure, a saturation magnetization of 6.16 emu/g and good capabilities for magnetic hyperthermia. Magnetoliposome-like structures containing the multicore nanoparticles exhibit sizes in the range 250 – 400 nm. A new antitumor thienopyridine derivative was loaded in these nanocarriers with a high encapsulation efficiency of 98% ± 2.6%. Release profiles in absence and presence of an AMF indicate a transport by diffusion, with a maximum compound release of 31% under the AMF. A sustained and controlled drug release in anticipated from the results, pointing to suitable characteristics of the magnetoliposomes for dual cancer therapy (combined magnetic hyperthermia and chemotherapy).

The abundant and renewable resources from fruit byproducts are getting emphasis on their valorization. These byproducts are suspected of possible toxications during cultivation, harvesting, transporting, preservation, or processing. Hence, presenting scientific overviews of the toxicological qualities and detoxification trends of these byproducts is critical to implicating their possible valorization. This review emphasized the toxicological qualities of byproducts from fruits for which the maximum global production occurred in 2022. In this review, heavy metals (As, Cd, Co, Cr, Ni, Pb, and Hg), mycotoxins, toxicant organic compounds, anti-nutritional factors, and pesticide/fungicide residues of the selected fruit byproducts were discussed. Current trends to reduce possible toxicants of these byproducts during their valorization were emphasized. Novel functional foods valorized from these fruit byproducts and future perspectives of detoxification were also focused on in this review.

Scholars in the field of environmental economics have extensively examined the relationship between foreign direct investment (FDI) and economic growth. However, they have often failed to consider the crucial roles played by technological innovation and financial development in determining environmental costs. The rapid economic growth and urbanization witnessed in BRICS countries have led to a substantial increase in energy demands, resulting in significant environmental degradation. This study aims to investigate the impact of financial development (including measures such as broad money, domestic credit to the private sector, FDI, and green technological innovation) on carbon emissions in BRICS countries using data from 2001 to 2023. The results of the study demonstrate a strong cross-sectional dependence among the countries in the panel. The Augmented Mean Group (AMG) estimator reveals a negative and statistically significant long-term relationship between broad money, FDI, green technological innovation, and CO2 emissions. On the other hand, domestic credit to the private sector shows a positive and significant association with carbon emissions. To determine the direction of causality, the study utilizes the Dumitrescu and Hurlin panel causality test. The findings indicate a non-directional long-term causality between financial development and CO2 emissions. However, a unidirectional causality is observed between green technological innovation and carbon emissions. Based on these findings, the study suggests that the development of industries, financial institutions, and technological innovation is crucial for attracting high-quality FDI in BRICS countries. However, it also highlights the significant contribution of these developments to environmental degradation, necessitating urgent policy responses.

Aflatoxin contamination (AC) increases as the severity of drought stress increase in peanut. Identifying drought-tolerant (DT) genotypes with resistance to Aspergillus. flavus in semi-arid tropics may aid in development of peanuts that minimizing aflatoxin contamination. The goal is to identify the DT genotypes and resistant to aflatoxin contamination. The experiments curried out at ICRISAT Sahelian Center on fifty-five genotypes assessed in adjacent intermittent water-stressed (WS) from 60th day after sowing to maturity and well-watered (WW) conditions in a randomized complete block design. The yields and components, incidence of A. flavus colonisation, aflatoxin contamination and the seed coat total pthe olyphenol (SCTPP) were estimated. Water deficit reduced pod yield, seed yield, and haulm yield up to 19.49%, 27.24% and 22.07% respectively and increased the immature pods plant-1, (IMPN) and aflatoxin contamination up to 67.16% and 54.95%. The genotypes ICG 2106, ICG 311, ICG 4684, ICG 4543, and ICG 1415 maintained high yield under WS, less of IMPN and the lowest AC variation between WW and WS. The drought tolerant genotypes showed the relationship with aflatoxin resistance and SCTPP (r2=0.80; r2=0.82) under WW and WS. These findings can be used to select the genotype that combine drought tolerance and minimizing aflatoxin contamination.

COVID-19, caused by SARS-CoV-2, was first identified in China in 2019. The exact origin of the disease remains uncertain, with theories suggesting it may have emerged from animals or accidentally leaked from a research laboratory. If the hypothesis that COVID-19 originated from a research laboratory is accurate, it is crucial to investigate potential pathways for pathogens to escape from biocontainment research animal facilities (BRAFs). We examine key biosafety issues associated with BRAFs, including inadequate decontamination procedures for water and experimental samples, handling high biosafety level pathogens in lower level laboratories, risks of animal bites and sharps injuries, contamination of bedding and enrichment materials, and improper management and transportation of biohazard samples. Additionally, we discuss the role of veterinarians in African research animal facilities and the challenges they encounter in maintaining biocontainment standards. We emphasize the importance of routine monitoring of effluent water to detect possible disease outbreaks. We recommend a thorough investigation of the COVID-19 pandemic to identify potential sources of pathogen release from BRAFs, which could serve as hotspots for future disease outbreaks. Findings from such investigations will inform the development of policies aimed at safeguarding human populations from future pandemics and preventing BRAFs from becoming sources of infectious disease outbreaks.

This paper presents a mathematical modeling approach utilizing a fuzzy modeling framework for fixed wing aircraft systems with the goal of creating a highly desirable mathematical representation for model-based control design applications. The starting point is a mathematical model comprised of fifteen non-linear ordinary differential equations representing the dynamic and kinematic behavior applicable to a wide range of fixed wing aircraft systems. Here the proposed mathematical modeling framework is applied to the AIRBUS A310 model developed by ONERA. The proposed fuzzy modeling framework takes advantage of sector non-linearity techniquesto recast all the non-linear terms from the original model to a set of combined fuzzy rules. The result of this fuzzification is a more suitable mathematical description from the control system design point of view. Therefore, the combination of this fuzzy model and the wide range of control techniques available in the literature for such kind of models will enable us to avoid common control design methods, such as gain scheduling, where stability issues can be extremely challenging.

Cytochrome P450s (CYP450s) are a versatile superfamily of enzymes known to undergo rapid evolution. They have important roles across growth and development pathways in crustaceans, although it is difficult to characterise orthologs between species due to their sequence diversity. Conserved CYP450s enzymes in crustaceans are those associated with ecdysteroidogenesis; synthesising and breaking down the active moult hormone, 20-hydroxyecdysone. The complex life-cycle of the ornate spiny lobster, Panulirus ornatus, relies on moulting in order to grow and develop. Many of these diverse life stages have been analysed to establish a comprehensive transcriptomic database for this species. The transcripts putatively encoding for CYP450s were mapped using transcriptomic analysis and identified across growth and development stages. With the aid phylogeny, 28 transcripts of 42 putative P. ornatus CYP450s were annotated, including the well conserved Halloween genes, which are involved in ecdysteroidogenesis. Expression patterns across the life-stages determined that only a subset of the CYP450s can be detected in each life-stage or tissue. Four Shed transcripts show overlapping expression between metamorphosis and adult tissues, suggesting pleotropic functions of the multiple Shed orthologs within P. ornatus.

Replication protein A (RPA) is a heterotrimeric protein complex and the main single-stranded DNA (ssDNA) binding protein in eukaryotes. RPA has key functions in most of the DNA-associated metabolic pathways and DNA damage signalling. Its high affinity for ssDNA helps to stabilise ssDNA structures and prevents the DNA sequence from nuclease attacks. RPA consists of multiple DNA-binding domains which are oligonucleotide/oligosaccharide-binding (OB)-folds, responsible for DNA binding, and interactions with proteins. These RPA-ssDNA and RPA-protein interactions are crucial for DNA replication, DNA repair, DNA damage signalling, and the conversation of the genetic information of cells. Proteins such as ATR use RPA to locate to regions of DNA damage for DNA damage signalling. Recruitment of nucleases and DNA exchange factors to sites of double strand breaks are also an important RPA function to ensure effective DNA recombination to correct these DNA lesions. Due to its high affinity to ssDNA, RPA’s removal from ssDNA is of central importance to allow these metabolic pathway to proceed and processes to exchange RPA against downstream factors are established in all eukaryotes. These facetted and multi-layered functions of RPA will be discussed in detail in the review. RPA is also a major player in a variety of human diseases, which will be discussed.

Soil sodicity is a major constraint to seedling emergence and crop production, potentially reducing plant growth due to physical and chemical constraints. Examining responses to ion imbalances may assist in the identification of genotypes tolerant to chemical constraints in sodic soils and improve productivity. We evaluated the performance of four wheat (Triticum aestivum. L) genotypes in solutions with five sodium adsorption ratios (SARs) ranging from 0 to 60. For all four genotypes, seedling emergence and shoot dry matter (DM) decreased significantly with increasing SAR. A significant positive correlation was observed between Ca concentration in roots, as well as both root and shoot DM for all genotypes. At SAR values &gt;20, a more tolerant genotype (EGA Gregory), had higher Ca concentrations in root tissues, while a more sensitive genotype (Baxter) exhibited Na-induced Ca deficiency. Thus, selection for genotypes that are able to accumulate Ca in roots in sodic conditions may be a useful trait for selecting genotypes tolerant of soils with high ESP values. However, for soils that restrict plant growth at ESP (SAR) values of 6-10%, it is likely that growth is restricted by physical constraints rather than by a Na-induced Ca deficiency.

Children with history of prematurity are at higher risk of complications, comorbidities and iron deficiency. In this study we assess the prevalence of restless sleep disorder, as well as that of periodic leg movements during sleep (PLMS) in these children. Retrospective chart review of sleep studies in children aged 1-18 years, with history of prematurity. Only diagnostic studies in children without diagnosis of a genetic syndrome or airway surgery or tracheostomy were included. Three groups were compared, children with PLMS index&gt;5, children with restless sleep disorder (RSD), and children with neither elevated PLMS index nor RSD. During the study, 2,577 sleep studies were conducted. Ninety-two studies fit our criteria and were included in analysis. Median birth age was 31 weeks, interquartile range (IQR) 27-34 weeks. Thirty-two (34.8%) children were referred for restless sleep and 55 (59.8%) for snoring; after polysomnography 18% were found to have PLMS index &gt;5/hour, 14% fit the criteria for RSD. There were no statistically significant differences in polysomnographic parameters between the children with RSD, PLMS and the remaining group, except for lower obstructive apnea/hypopnea index (Kruskal-Wallis ANOVA 8.621, p=0.0135) in the RSD group (median 0.7, IQR 0.3-0.9) than in the PLMS (median 1.7, IQR 0.7-3.5), or than in the nonRSD/nonPLMS group (median 2.0, IQR 0.8-4.5). There was elevated frequency of RSD and elevated PLMS in children with history of prematurity that might be linked to the increased risk of iron deficiency in premature infants. These new results add new knowledge on the prevalence of RSD in these children.

The incidence of breast cancer and therefore need for breast reconstruction is expected to increase. The many reconstructive options available and the changing aspects of the field make this a complex area of plastic surgery, requiring knowledge and expertise. Two major types of breast reconstruction can be distinguished: Breast Implants and Autologous Flaps. Both present advantages and disadvantages. Autologous fat grafting is also commonly used. MRI is the modality of choice for evaluating breast reconstruction. Knowledge of the type of reconstruction is preferable to provide the maximum of pertinent information and avoid false positives. Early complications include seroma, hematoma, and infection. Late complications depend on the type of reconstruction. Implant rupture and implant capsular contracture are frequently encountered. Depending on the implant type, specific MRI signs can be depicted. In case of myocutaneous flap, fat necrosis, fibrosis and vascular compromise represent the most common complications. Late cancer recurrence is much less common. Rare reported late complications include breast implant associated large cell anaplastic lymphoma (BIA-ALCL) and, recently described and even rarer, Breast implant-associated squamous cell carcinoma (BIA-SCC). In this review article, the various types of breast reconstruction will be presented, with emphasis on pertinent imaging findings and complications.

The viral nervous necrosis virus (VNNV) is the causative agent of an important disease affecting fish species cultured worldwide. Early and accurate diagnosis is at present the most effective control and prevention tool, and the molecular techniques have been strongly introduced and accepted by official organizations. Among those, real time quantitative polymerase chain reaction (rt-qPCR) is nowadays displacing other molecular techniques. However, another PCR-based technology, the droplet digital PCR (ddPCR), is on the increase. It has many advantages over qPCR, such as higher sensitivity and more reliability of the quantification. Therefore, we decided to design and validate a protocol for diagnosis and quantification of SJ and RG type VNNV, using reverse transcription-ddPCR (RT-ddPCR). We obtained an extremely low limit of detection, 10 to 100-folds lower than with RT-qPCR. Quantification by RT-ddPCR, with a dynamic range of 6.8 – 6.8 x 104 (SJ type) or 1.04 x 101 – 1.04 x 105 (RG) cps/rctn, was more reliable than with RT-qPCR. The procedure was tested and validated in field samples, providing the high clinical sensitivity and negative predictive values. In conclusion, we propose this method to substitute RT-qPCR protocols because it exceeds the expectations of qPCR in the diagnosis and quantification of VNNV.

Depression and anxiety are the most common mental health disorders worldwide. Internet-Delivered Cogni-tive Behaviour Therapy (ICBT) can reduce barriers to care for broad cross sections of the population. How-ever, People of Diverse Ethnocultural Backgrounds (PDEGs) other than White/Caucasian underutilize mental health services and are underrepresented in clinical trials of psychological interventions. To address this research gap, we adapted an evidence-based ICBT program for PDEGs. The current pilot study explores the effectiveness, satisfaction, and engagement in the adapted ICBT by PDEGs (N=41) when benchmarked against a sample of PDEGs (N=134) drawn from a previous non-adapted version of the ICBT program. Inntent-to-treat analyses showed that the adapted ICBT program is effective in reducing anxiety and de-pression symptoms among PDEGs. Large within-group pre-to-post-treatment Cohen’s effect sizes of d = 1.23, 95% CI [0.68, 1.77] and d = 1.24, 95% CI [0.69, 1.79] were found for depression and anxiety, respectively. Further, 81.8% of the PDEGs who received the adapted ICBT program reported high overall satisfaction, 90.9 % reported increased confidence in managing symptoms, and 70.7% of participants completed the ma-jority of the psychoeducational lessons in the ICBT program. No statistically significant differences in clinical outcomes, engagement, and satisfaction were found between the pilot study and benchmark sample. Future directions for ICBT research with PDEGs are described.

Metallo-β-lactamases (MBLs) are a group of Zn(II)-dependent enzymes that pose a major threat to global health. They are linked to an increasing number of multi-drug resistant bacterial pathogens, but no clinically useful inhibitor is yet available. Since β-lactam antibiotics, which are inactivated by MBLs, constitute ~65% of all antibiotics used to treat infections, the search for clinically relevant MBL inhibitors is urgent. Here, derivatives of a 2-amino-1-benzyl-4,5-diphenyl-1H-pyrrole-3-carbonitrile (1a) were synthesised and their inhibitory effects assessed against representatives of each of the three subgroups of MBLs (B1, B2, B3). Several compounds are potent inhibitors of each MBL tested, making them excellent candidates for the development of broad-spectrum drug leads. In particular, compound 5f is highly potent across the MBL subfamilies, with Ki values in the low µM range. Furthermore, this compound also dis-plays synergy in combination with antibiotics such as penicillin G, cefuroxime or meropenem. This molecule thus represents one of the most promising compounds developed yet to combat MBLs.

The development of antimicrobial resistance to conventional antibiotics is a major global health challenge. Infections caused by multidrug-resistant gram-negative bacteria have been named one of the most urgent global health threats. Considerable efforts are devoted to developing new antibiotic drugs and investigating the mechanism of antibiotic resistance. Recently, Anti-Microbial Peptides (AMPs) have emerged as a new platform for the target and design of novel drug resistant anti-microbial agents promising a new therapeutic strategy. AMPs are rapid, potent, possess an unusually broad spectrum of activity, and have shown efficacy as topical agents. Unlike traditional therapeutics that interfere with essential bacterial enzymes, AMPs interact with microbial membranes through electrostatic interactions and physically damage cell integrity. However, naturally occurring AMPs have limited selectivity and modest efficacy. Therefore, recent efforts have focused on the development of synthetic AMP analogs as suitable drug targets. This work explores the development of novel antimicrobial agents which mimic the structure of graft-copolymers and mirror the mode of action of an AMP. Chitosan-graft-polypeptide side chains are synthesized by the ring-opening polymerization of N-carboxyanhydrides of L-lysine and L-leucine initiated from the functional groups of chitosan. The derivatives with random- and block-copolymer side chains are explored as drug targets. These graft copolymer systems exhibit activity against clinically significant pathogens and disrupt biofilm formation. This work highlights the potential of chitosan-graft-polypeptide structures in biomedical applications.

A quark nugget is a hypothetical dark-matter candidate composed of approximately equal numbers of up, down, and strange quarks. Most models of quark nuggets do not include effects of their intrinsic magnetic field. However, Tatsumi used a mathematically tractable approximation of the Standard Model of Particle Physics and found that the cores of magnetar pulsars may be quark-nuggets in a ferromagnetic-liquid state with surface magnetic field Bo = $10^(12±1) T. We have applied that result to quark-nugget dark matter. Previous work addressed the formation and aggregation of magnetized quark nuggets (MQNs) into a broad and magnetically stabilized mass distribution before they could decay and addressed their interaction with normal matter through their magnetopause, losing translational velocity while gaining rotational velocity and radiating electromagnetic energy. The two orders of magnitude uncertainty in Tatsumi’s estimate for Bo precludes the practical design of systematic experiments to detect MQNs through their predicted interaction with matter. In this paper, we examine episodic events consistent with a unique signature of MQNs. If they are indeed caused by MQNs, they constrain the most likely values of Bo = 1.65 × 10^12 T +/- 21% and support the design of definitive tests of the MQN dark-matter hypothesis.

To obtain an accurate and reproducible experimental results in microbial fuel cell (MFC), it is important to know ‘anode maturation biofilm’ to produce a stable and maximum performance. For this purpose, four single chamber MFCs were tested in this study. The linear sweep voltammetry (LSV) polarization tests illustrated that maximum power densities of three MFCs became stable after 9 weeks. Although there were variations afterwards, such variations were negligible. Average maximum power densities from the 9th to the 17th week were 2,990 mW/m2 (MFC-4), 2,983 mW/m2 (MFC-2), 2,368 mW/m2 (MFC-3) and 837 mW/m2 (MFC-1). Polarization resistance shows that MFC-1 had much larger anode resistance (36.6-85.4 Ω) than the other MFCs (1.7-11.6 Ω). Anodic cyclic voltammetry (CV) shows that current production increased over time and MFC-1 had much smaller current production (24.4 mA) than the other MFCs (31.0-34.9 mA) at 17th week. The increased current production indicates anode biofilm became more mature over time, but overall cell performance did not increased accordingly. Possibly due to the bad inoculation, MFC-1 showed the lowest performance. However, its performance was restored to the initial performance and anode resistance was reduced by 47% at 17th week. This study shows that the optimum anode maturation time is 9 weeks and that bioanode performance is a key factor for MFC performance. This study also shows than LSV polarization and CV tests are accurate and non-destructive measurement methods for diagnosing anode performance.

In this study we used a recently developed ex vivo-in vitro model to assess the effect of feeding older adults a casein protein hydrolysate (CPH) compared with non-bioactive non-essential amino acid (NEAA) supplement on Muscle Protein Synthesis (MPS) and Breakdown (MPB). Serum from six healthy older males following overnight fast and 60 min postprandial ingestion of CPH or NEAA (0.33 g.kg^-1 body mass) was used to condition C2C12 myotube media. CPH-fed serum significantly increased MPS compared to fasted serum. In addition, CPH-fed serum induced myotube growth and markedly suppressed atrogin-1, but not MuRF1, expression. Comparatively, no change in MPS, myotube growth and gene expression was observed following NEAA-fed serum treatment. CPH-fed serum from older adults stimulated de novo MPS, suppressed markers of protein breakdown and resulted in myotube growth, indicating a potential role for CPH as a dietary protein source to prevent age-related sarcopenia.